Scribd
Upload
17 views

JSS-6-Training Needs

training needs

Uploaded by

panoy subang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
17 views

JSS-6-Training Needs

training needs

Uploaded by

panoy subang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Trainees Training Requirement

Name : Thomas F. Martin


Qualification: AUTOMOTIVE SERVICING NCII

Module Title/Module of
Gaps Duration (hours)
Instruction

1. Test automotive battery 10hrs

2. Remove and replace


10hrs
batteries.
SERVICING AUTOMOTIVE
3. Service and charge BATTERY
15hrs
batteries.

4. Jump-start vehicle. 5hrs

1. Check Ignition System 6hrs

2. Perform spark test 6hrs

3. Check ignition coil


6hrs
resistance

4. Check ballast resistor 5.5hrs

5. Adjust contact point


SERVICING IGNITION 6hrs
clearance (if any)
SYSTEM
6. Perform ignition wiring
6hrs
installation

7. Perform ignition timing 6hrs

8.Repair non-electronic

ignition system and/or 6hrs

components

1. Test electrical systems TESTING AND REPAIRING 24hrs


WIRING/LIGHTING
2. Repair electrical SYSTEMS 23.5hrs
systems

1. Test system/

components and identify 23.5hrs


faults
SERVICING STARTING
2. Repair starting SYSTEM
24hrs
systems associated

components

1. Test system/

components and identify 23.5hr


faults
SERVICING CHARGING
2. Repair charging SYSTEMS

system associated 24hrs

components

1.Service cooling system 12hrs

2. Service lubricating
12hrs
system SERVICING ENGINE
3. Service fuel system MECHANICAL SYSTEM 11.5hrs

4. Service diesel fuel


12hr
injector

1. Diagnose clutch
7.5hrs
failure/problem

2. Pull-out and mount


8hrs
clutch component parts

3. Overhaul hydraulic
8hrs
clutch mechanism

4. Perform clutch parts


8hrs
failure analysis

5. Set/Adjust clutch SERVICING CLUTCH 8hrs


system components
6. Bleed clutch hydraulic
8hrs
system SYSTEM

1. Inspect drive shaft


7hrs
and joint

2. Dismount differential
7hrs
assembly

3. Overhaul differential 7hrs


SERVICING
4. Mounting differential DIFFERENTIAL AND
7hrs
assembly FRONT/REAR AXLE
5. Overhaul rear/front
7hrs
wheel hub

6. Analyze king pin


5.5hrs
condition

7. Inspect/replace I-beam 7hrs

1. Analyze front end


11.5hrs
geometry failure

2. Service steering
14hrs
system SERVICING MANUAL
STEERING SYSTEM
3. Perform wheel
12hrs
balancing

4.Conduct wheel
12hrs
alignment

1. Pull-out/mount brake
16hrs
system components

2. Disassemble/ SERVICING BRAKE


assemble brake system SYSTEM 16hrs
components

3. Conduct road test 15.5hrs

1. Diagnose suspension SERVICING SUSPENSION 11.5hrs


system failure

2. Dismount/mount

Suspension components 12hrs

parts

3. Disassemble/ SYSTEM
Assemble suspension 12hrs
parts

4. Inspect/replace

Suspension component 12hrs


parts

1. Check clutch fluid and


5.5hrs
lines

2. Inspect brake system 6hrs

3. Inspect/change

transmission/ 6hrs

differential gear oil

4. Inspect/Replace PERFORMING
UNDERCHASSIS 6hrs
Power steering fluid PREVENTIVE
4. Inspect/Replace MAINTENANCE
6hrs
power steering fluid

5. Check/Re-fill automatic
6hrs
transmission fluid

6. Inspect/Bleed air tank 6hrs

7. Check tires and tire


6hrs
pressures

8. Check under chassis


6hrs
body bolts and nuts

1. Diagnose manual OVERHAULING MANUAL 7hrs


Transmission failure

2. Pull-out manual
7hrs
transmission

3. Disassemble manual 12.5hrs

transmission

4. Inspect manual 7hrs


TRANSMISSION
Transmission parts

5. Assemble manual 7hrs

transmission

6. Test manual 7hrs


transmission

7. Road test 5.5hrs


Transmission

You might also like