Product Data Sheet

Edition 13/02/2008
Identification no: Ε.02.03
SikaBond®-T19

SikaBond®-T19
Adhesive for Raised access floors
Product
Description ®
SikaBond -T19 is an elastic, 1-component, polyurethane-based adhesive.
®
Uses SikaBond -T19 is used in the installation of platform and raised access floors for
the fixing of the pedestals.
Platform and screeded cavity floor systems are found in administrative buildings,
hospitals, communications and computer centres, control rooms, laboratories and
clean rooms and are commonly used in refurbishment and office modernisation
schemes.
®
The elastic adhesive SikaBond -T19 absorbs vibration and reduces sound
transmission.
Characteristics / n 1- component
Advantages n Solvent free
n Elastic
n Easy application
n Suitable for bonding of pedestals for raised access floors according to RAL-GZ
941 class 1-3 and for screeded cavity floors
n Tested in conjunction with Sikafloor  2530 W water based, 2-component epoxy
resin floor coating
n Good adhesion without priming on concrete, chipboards, plywood, fibre-
reinforced gypsum and cement boards

Product Data

Form
Colours Natural
Packaging 600 ml sausages (1 box = 20 sausages)

Storage
Storage Conditions / 12 months from date of production if stored in undamaged original sealed
Shelf Life containers, in dry conditions and protected from direct sunlight at temperatures
between +10°C and +25°C.

Technical Data
Chemical Base 1-component PU moisture curing
Density ~ 1.41 kg/l (DIN 53 479)
Skinning- Time ~ 50 minutes (+23°C / 50% r.h.)

Curing Rate ~ 4 mm / 24h (+23°C / 50% r.h.)

1 SikaBond®-T19 1/3
Sag Flow Non sagging
Service Temperature -40°C to +80°C

Mechanical Properties
Horizontal Shear Class 1 to 3 according to RAL-GZ 941 quality control for approx. 2 mm, adhesive
Strength coat thickness, approx. 80 cm2 pedestal area, 50 cm pedestal height
2
Tensile Strength ~ 1.2 N/mm (+23°C / 50% r.h.) (DIN 53 504)
Shore A Hardness ~ 40 (after 28 days) (DIN 53 505)
Elongation at Break > 600% (+23°C / 50% r.h.) (DIN 53 504)

System
Information

Application Details
Consumption Approx. 28 g or 20 ml of adhesive is required for a pedestal area of 80 cm².
Substrate Quality Clean and dry, homogeneous, even, and free from grease, dust and loose particles.
Paint, laitance and other poorly adhering particles must be removed. Any coatings
must be compatible with the adhesive
The pedestal base plates (galvanised, yellow passivated etc.) must be clean, dry
and free from dust, grease and oil.
Substrate Preparation To clean and degrease the pedestal surface, use Colma Cleaner or an equivalent
degreasing agent.

Application
Conditions / Limits
Substrate Temperature > +5°C.
Air Temperature +5°C min. / +35°C max.
Substrate Humidity Dry
Relative Air Humidity Between 30% and 90%

Application
Instructions
Application Method / Use hand- or air-pressure gun.
Tools
Apply SikaBond-T19 to the pedestal base plate or to the substrate. The required
quantity of adhesive depends on the nature of the substrate and the pedestal
surface, which must be fully coated with adhesive. Approx. 28 g or 20 ml of
adhesive is required for a pedestal area of 80 cm². The pedestal is then accurately
positioned on the substrate and pressed firmly into the adhesive so as to ensure a
adhesive layer thickness of approx. 1.0 to 2.0 mm.
Fresh, uncured adhesive remaining on the surface must be removed immediately
® ®
with a clean cloth and if necessary cleaned with Sika Remover-208 or Sika
Handclean towels.
®
Cleaning of Tools Clean all tools and application equipment with Sika Remover-208 immediately
after use. Hardened / cured material can only be removed mechanically.
Potlife (max. open time) ~ 30 minutes
Notes on Application /
Limits For the proper curing of the adhesive sufficient ambient moisture is necessary.
Do not use on PP, PE, Teflon and certain plasticized synthetic materials (carry out
pre-trials or contact our Technical Service).

Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.

Local Restrictions Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.

2 SikaBond®-T19 2/3
Health and Safety For information and advice on the safe handling, storage and disposal of chemical
products, users should refer to the most recent Material Safety Data Sheet
Information containing physical, ecological, toxicological and other safety-related data.

Legal Notes The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sika’s recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any other
advice offered. The user of the product must test the product’s suitability for the
intended application and purpose. Sika reserves the right to change the p roperties
of its products. The proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.

Sika Hellas ABEE Phone +30 210 8160600-5

3 SikaBond®-T19 3/3