CODES - THE BASICS OPERATING INSTRUCTIONS

KL1OOO Vertical
POI-KL1000NC- v3:0813
NC
• The KitLock has five code levels FUNCTIONS C) NETCODE Note: The KitLock has a 10 button Blue LED = Code accepted LOST CODE PROCEDURE PENALTY TIME BATTERY FAILURE OVERRIDE
available: Before programming, select the The NetCode function enables keypad and a # button. Note: The procedure requires the • Entering three incorrect codes The KitLock has been designed so an
i) Master Code most appropriate function for the the lock owner to generate time The # button is hidden beneath the Red LED = Code rejected door to be open: will cause the lock to shutdown external PP3 battery can be placed against
ii) Sub-Master Code application: sensitive codes for locks installed handle when in the locked position. • Remove the rear-fixing bolt and for 10 seconds. the contact points surrounding the Blue
iii) User Code A), B) or C) – See Special remotely. NetCode function is swing the lock over the edge of the and Red LEDs so the lock can be opened
iv) Technician Code Master Code set up activated prior to shipping to CODES The lock has the following code levels: door to reveal the battery compartment. BATTERY POWER to replace the batteries should they fail.
v) NetCode commands. remote site/installation via web • Remove one battery. • The KitLock should provide well
• The KitLock is supplied with two based application. This function is • Press and hold the 1 button, replace in excess of 15,000 openings, of 4 The procedure is as follows:
MASTER CODE TECHNICIAN CODE the battery, the Blue LED will flash
factory set codes: A) PRIVATE USE typically used for issuing codes to The Master Code can: The Technician Code can: seconds each, from 2 x AAA 1.5v cells. • Place the contact points of the PP3
Master Code: 11 33 55 77 Important Note: This is visiting service engineers, delivery twice, release the 1 button. Within battery against the contact points
www.kitlock.com • Open the lock. • Open the lock. three seconds press the 1 button
User Code: 22 44 the default function and is personnel (drop boxes), medium • Change the Master Code. LOW BATTERY surrounding the Blue and Red LEDs.
[email protected] three times. The Blue LED will flash
• Before fitting change the Master already pre-programmed in term locker rental. Generated • Set / Change / Delete the Sub-Master NETCODE • When the battery power is low the • The positive + PP3 terminal against
[email protected] twice and the lock will have reverted
Code and User Code. new locks. This is the most codes can be sent by email or and User Code. The NetCode can: to the factory Master Code 11 33 55 77 • Red LED will flash 3 times before the Red LED contact point and the
KitLock is a Codelocks Limited Brand
• All Master Codes and Sub-Master common function and is used SMS to any email account or • Select between Private and • Open the lock for a particular date, and all other stored settings will the • Blue LED lights, accepting the negative – PP3 terminal against the
CODELOCKS LTD UK Codes are 8 digits long. where the same code will be mobile phone via a password Public Functions. time and duration. be erased. code. Fit new batteries as soon as this Blue LED.
Tel: +44 (0) 1635 239645 happens. The lock will operate for 100 • Enter the Master Code.
• All User Codes are 4 digits long. repeatedly used. protected kitlock.net account. • Activate/deactivate Technician Code.
Fax: +44 (0) 1635 239644
[email protected] • All Technician Codes are • Activate NetCode. A code cannot be programmed times with low battery. • The motor will withdraw the locking pin
Helpline, service & spares 6 digits long. B) PUBLIC USE into more than one level. allowing the lock to be opened.
FREEPHONE 0800 393 405 • All NetCodes are 12 digits long. The user enters their own personal SUB-MASTER CODE •  low
Code rejected • Fit new batteries by removing the
• The lock ‘open’ time is set four-digit code twice, the second battery indication upper fixing bolt and swinging the lock
CODELOCKS INC US The Sub-Master Code can: Programming
Tel: +1 714 979 2900
Fax: +1 714 979 2902
at 4 seconds. time to confirm the correct code.
This locks the lock. The same
• Open the lock. • Code accepted down over the edge of the door.
Refit the lock.
& Operating
[email protected] • Change the Sub-Master. Instructions
Help: 1.877.CODELOCK code is entered once only to open • Set / Change / Delete / the User Code. PROGRAMMING for Netcode
www.codelocks.com the lock before being erased and
To program – the lock must be in
ready for the next new user. This USER CODE the open position with the # button
function is used for short term, The User Code can: visible. Every program command must
multi occupancy applications, • Open the lock. commence by pressing the # button,
e.g. a locker in a leisure centre. • Change the User Code. followed by either the Master Code,
Sub-Master Code or User Code.
 CHANGE THE MASTER CODE CHANGE THE SUB-MASTER CODE SET A) PRIVATE USE SET C) NETCODE CREATE PERSONAL USER CODE
MASTER CODE COMMANDS

SUB-MASTER CODE COMMANDS

SPECIAL MASTER CODE COMMANDS

GENERATE NETCODES

SPECIAL FUNCTIONS
• • •
#Master Code 01 New Master Code New Master Code •• • •
#Sub-Master Code 06 New Sub-Master Code • #Master Code • •• 26 1) CREATE A KITLOCK.NET ACCOUNT A user with a NetCode can create a shorter, more memorable code
• •
Example: #11335577 01 12345678 • ••
12345678 New Sub-Master Code •• • ••
Example: #11335577 26 Step 1: Visit www.kitlock.net which will have the same validity period as the user’s NetCode.
Result: Master Code has been changed to 12345678. • •
Example: #87654321 06 10101010 10101010 • •• Result: The lock will revert back to default A) Private Use Function. Step 2: Create a new account – you will need a valid email address. ##NetCode • • 01 Personal User Code •
Result: Sub-Master Code has been changed to 10101010. Factory set User Code 2244 will now work repeatedly until reprogrammed. If you already have a KitLock.net account, you can skip this step. ••
Personal User Code
Example: ##392100136860 • • 01 6688 • 6688••
SET OR CHANGE THE USER CODE SET OR CHANGE THE USER CODE SET B) PUBLIC USE 2) REGISTER YOUR LOCK Result: The Personal User Code 6688 will open the lock.
• • ••
#Master Code 02 User Code • •
#Sub-Master Code 07 User Code •• #Master Code • •• 24 Step 1: Visit www.kitlock.net [Go to step 3 if already logged in].
• • ••
Example: #11335577 02 9999 Example: #87654321 • •07 6666 •• • ••
Example: #11335577 24 Step 2: Log-in. USE OF A PERSONAL USER CODE
Result: New User Code 9999 now operative. Result: New User Code 6666 now operative. Result: The lock will now remain open until the next user enters their own Step 3: Click Register My Lock. Personal User Code •
personal code into the lock as follows: Step 4: Follow on-screen instructions. Example: 6688 •
DELETE USER CODE Step 1 – Enter 4 digit code • Confirm 4 digit code•• Step 5: Click Save to complete. Result: Lock opens.
DELETE USER CODE #Sub-Master Code 08 • •• Close the locker which will now be locked.
#Master Code 03• •• Example: #87654321 • •• 08 Step 2 – Enter the same 4 digit code •• the lock will now open and remain 3) CREATE A NET CODE MANUAL DELETE OF NETCODE
• ••
Example: #11335577 03 Result: User Code deleted. open until next 4 digit code is entered. Step 1: Click Create NetCode. #Master Code • •11 •• NetCode
Result: User Code deleted. Note: When locked in this mode • LED will flash every 5 seconds to indicate Step 2: Select your lock from the list. • •
Example: #11335577 11 392100136860 ••
the locker is locked. Step 3: Choose a date & time from which the code will be valid. Result: NetCode 392100136860 has been deleted.
Step 4: Choose a length of time for the code to work.
SET OR CHANGE THE SUB-MASTER CODE SET TECHNICIAN CODE The code will be deleted after this period. MANUAL DELETE OF A NETCODE VIA ANOTHER NETCODE

USER CODE COMMANDS

• • •
#Master Code 04 Sub-Master Code Sub-Master Code •• #Master Code • • 99 Technician Code• Technician Code •• Step 5: Enter a note about the code if required. ##NetCode • • 02 Unwanted NetCode ••
• •
Example: #11335577 04 87654321 • ••
87654321 CHANGE THE USER CODE • •
Example: #11335577 99 555555 • 555555 •• Step 6: Click Create to complete. Example: ##471100538860 • •
02 392100136860 ••
Result: Sub-Master Code 87654321 now operative. #User Code • New User Code •New User Code •• Result: The lock is automatically set into B) Public Use Function and allows the Result: NetCode 392100136860 and any related Personal User Code
Example: #2244 • 6688 •6688 •• programmed Technician Code to open the lock WITHOUT the entered single 4) ADDITIONAL KITLOCK.NET FEATURES has been deleted by NetCode 471100538860.
Result: User Code now 6688. use code being erased. Once a NetCode has been created, you can choose to email or SMS the code
DELETE THE SUB-MASTER CODE Note: If lock is opened with a Master Code the User Code will be erased. to any email account or mobile phone*. CHANGE DATE & TIME
• • ••
#Master Code 05 05 * Additional charges apply for SMS delivery. See www.kitlock.net/addons It is recommended to update the date and time once a year or after
• • ••
Example: #11335577 05 05 for details. changing the batteries.
Result: Sub-Master Code deleted. #Master Code • • 12 YYMMDD • HHmm ••
Example: #11335577• • 12 130522 • 11:00••
Result: Lock internal clock updated to 22/05/2013 11:00.