Scribd
Upload
36 views

Assignment 1 Series Parallel

series parallel practice

Uploaded by

NISARG PATEL
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views

Assignment 1 Series Parallel

series parallel practice

Uploaded by

NISARG PATEL
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Department of Electronics & Communication Engineering

(Faculty of Technology, Dharmsinh Desai University, Nadiad)

Academic Year: 2024 - 2025

ASSIGNMENT – 2 [Series and Parallel Tuned Circuit]

Subject : (EC512) Electronics Communication


Class : B. Tech. Sem.V (EC)

Due Date :

Q.1 Select the most appropriate option.

(1) The parallel tuned circuit is tuned at 1 MHz using coil having Q factor of 150,
inductance of 20 mH and series resistance of 20 Ω. Determine the impedance offered
by the circuit at resonance.
(a) 20  (b) 3 k (c) 450 k (d) none of the above
(2) The series tuned circuit exhibit ___________ nature at resonant frequency.
(a) capacitive (b) inductive (c) resistive (d) can’t say
(3) For RF tuned circuit, higher Q factor ensures : (It may have more than one correct
answer)
(a) better selectivity (b) larger bandwidth
(c) narrow frequency response (d) lesser bandwidth
(4) The relative response of tuned circuit is given by _____________, where Q is Quality
factor and y is given by (ω/ω0) – (ω0/ω).
(a) 1/(1+jyQ) (b) r(1+jyQ) (c) r/(1+jyQ) (d) 1+jyQ
(5) Two coils having Quality factor Q1 and Q2 , inductance L1 and L2 , coil resistance
r1 and r2 are connected in series. The overall Q factor in terms of individual Q factor
and individual resistance will be ___________________ , assuming coupling
coefficient is 0.
(a) Q1+Q2 (b) (Q1r1+Q2r2)/(r1+r2)
(c) (Q1+Q2)/2 (d) (Q1r2+Q2r1)/(r1+r2)
(6) For a series tuned circuit at resonance, the voltage across the capacitor will be _____,
where Vin is voltage applied to series tuned circuit and Q is the quality factor of the
circuit.
(a) Q*Vin (b) Vin / Q (c) Vin (d) insufficient data

Q.2 [A] Answer in Brief (Short Questions)

(1) 1 𝐿
Prove that Q-factor 𝑄 = 𝑟 √𝐶
(2) The relative response of the tuned circuits is _______ dB at resonant frequency.
Justify your answer.
(3) In a parallel tuned circuit, Q- factor is also known as ________magnification factor.
Justify your answer.
(4) The series tuned circuit is tuned at f0 using coil having Quality factor of Q, inductance
of L and series resistance of r. Derive the expression to find the value of capacitance.
(5) For the circuit shown in figure below, the series tuned circuit is to be resonated at ____
frequency (f1 or f2), if you want I1 current to flow through RL and don't want I2 current
through RL. Justify your answer.

Q.2 [B] Answer in Brief (Short Questions)

(1) Derive the expression for determining bandwidth of LC series tuned circuit.
(2) In CE amplifier, where we should connect series tuned circuit to obtain highest gain
at resonant frequency and why?
(3) In CE amplifier, where we should connect parallel tuned circuit to obtain highest gain
at resonant frequency and why?

Q.3 Do as Directed (Descriptive Answers, Examples etc)

(1) A parallel tuned circuit has a Q factor of 200 when tuned to resonance at 10 MHz
Determine the dynamic impedance of the circuit.
(2) Determine the -3 dB bandwidth of the tuned circuit, having Q = 100 and fo = 1.3 MHz
(3) Calculate the -3 dB bandwidth for a parallel tuned circuit having resonant frequency
of 1.3 MHz, Q factor of 100 and tuning capacitance of 57 pF. Also determine the L
and dynamic impedance.
(4) A series tuned circuit has a Q of 130 and a tuning capacitance of 250 pF and is resonant
at 450 kHz. Calculate the relative response as a ratio, and in decibels, at a frequency
of 400 kHz.
(5) Given that the resonant frequency of the series tuned circuit, used in series wave trap
circuit, is 2 MHz and the Q-factor is 95, determine the rejection ratio of the unwanted
signal relative to a wanted signal at 2.2 MHz. The load resistance can be assumed
sufficiently high to be ignored.

You might also like