Scribd
Upload
12 views2 pages

11th JEE 2.8.24

Bay

Uploaded by

Rahul Kumar Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
12 views2 pages

11th JEE 2.8.24

Bay

Uploaded by

Rahul Kumar Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

1. In a vernier callipers, one main scale division is x cm (3) (10 ± 0.

001) cm2 (4) (10 ±1) cm2


and n division of the vernier scale coincide with (n -1) 8. The percentage errors in the measurement of a mass
divisions of the main scale. The least count (in cm) of and speed are 2% and 3% respectively. How much will
the callipers is be the maximum error in the estimate of kinetic energy
obtained by measuring mass and speed ?
 n 1  nx (1) 11% (2) 8%
(1)  x (2)
(n  1) (3) 5% (4) 1%
 n 
v
x x 9. The resistance R  where V = 100 ± 5 volts and
(3) (4) i
n (n  1)
i = 10  0.2 amperes. What is the total error in R
2. The circular divisions of shown screw gauge are 50. It
(1) 5 % (2) 7 %
moves 0.5 mm on main scale in one rotation. The
diameter of the ball is 5
(3) 5.2 % (4) %
2
10. The radius of the sphere is (4.3 ± 0.1)cm. The
percentage error in its volume is
0.1 0.1100 2
(1)  100 (2) 3 MLT
(1) 2.25 mm (2) 2.20 mm 4.3 4.3
(3) 1.20 mm (4) 1.25 mm
3. A vernier callipers has 1 mm marks on the main scale. It 1 0.1 100 0.1 100
(3)  (4) 3 
has 20 equal divisions on the Vernier scale which match 3 4.3 4.3
with 16 main scale divisions. For this Vernier callipers , 11. The density of the material of a cube is measured by
the least count is measuring its mass and length of its side. If the
(1) 0.02 mm (2) 0.05 mm maximum errors in the measurement of mass and the
(3) 0.1 mm (4) 0.2 mm length are 3% and 2% respectively. The maximum error
4. Two full turns of the circular scale of a screw gauge in the measurement of density is
cover a distance of 1 mm on its main scale. The total (1) 1 % (2) 5 %
number of divisions on the circular scale is 50. Further, (3) 7 % (4) 9 %
it is found that the screw gauge has a zero error of
-0.03 mm. While measuring the diameter of a thin wire, 12. A physical quantity is represented by X  M a LbT  c
a student notes the main scale reading of 3 mm and the If percentage errors in the measurements of M, L and
number of circular scale divisions in line with the main T are  %,  % and  % respectively, then total,
scale as 35. The diameter of the wire is
percentage error is
(1) 3.32 mm (2) 3.73 mm
(3) 3.67 mm (4) 3.38 mm (1) ( a   b   c )%
5. A screw gauge gives the following reading when used (2) ( a   b   c )%
to measure the diameter of a wire.
Main scale reading : 0 mm (3) ( a   b   c )%
Circular scale reading : 52 divisions (4) 0 %
Given that 1 mm on main scale corresponds to 13. A body travels uniformly a distance of (13.8 ± 0.2) m in
100 divisions of the circular scale. a time (4.0 ± 0.3) s. The velocity of the body within
The diameter of wire from the above data is error limits is
(1) 0.052 cm (2) 0.026 cm (1) (3.45± 0.2) ms-1 (2) (3.45± 0.3) ms-1
(3) 0.005 cm (4) 0.52 cm (3) (3.45±0.4) ms -1
(4) (3.45± 0.5) ms-1
6. The dimensional formula of relative density is 14. A physical quantity A is related to four observables a, b,

(1) ML
3
(2) LT
1 a 2b 3
c and d as follows A 
(3) MLT 2 (4) Dimensionless c d
7. A plate has a length (5 ± 0.1) cm and breadth (2 ± 0.01) The percentage errors of measurement in a, b, c and d
cm. Then the area of the plate is
(1) (10 ± 0.25) cm2 (2) (10 ±0.01) cm2

IIB-PCB EXAM PAGE NO. 2


are 1%, 3%, 2% and 2% respectively. What is the
percentage error in the quantity A?
(1) 12 % (2) 7 %
(3) 5 % (4) 14 %
15. The dimensions of universal gravitational constant are .
(1) M 2 L2T 2 (2) M 1L3T 2
(3) ML1T 2 (4) ML2T 2

IIB-PCB EXAM PAGE NO. 3

You might also like