SINCE

1987

MAKING SENSE (AND USE) OF SOLAR PANEL SPECIFICATIONS

DO IT YOURSELF OR HIRE A PRO?

The Risks & Rewards of DIY Solar-Electric Installation

Plus:
Build a Solar Space Heater Sun-Powered Water Pumping Slash Your Water Waste

Oct & Nov 2011, Issue 145 $5.95 US $5.95 CAN

homepower.com

Continuous Innovation.
Greater Efficiency. Easier Installation.

The YGE-Z Series

For residential and commercial applications where cost savings, installation time and aesthetics matter most.

3108

BooTh

See Yingli Solars new lineup at Solar Power International

AvErAGE CELL

18.5
%

EffICIENCY

The PANDA Series

Our most efficient module series yet, yeilding over 18.5% average cell efficiency.

Yingli Solar, DC Power Systems and Solar Depot.

SOLAR DEPOT

A powerful combination of innovation and distribution.

Learn more at solarnetholdings.com

U.S. Soccer Powered by Yingli Solar

Distributed by:

Im Plugged into AEE Solar

We have been installing systems since 1979. In our line of work, we need reliability. AEE Solar has continually provided us with professional service and great products.
PPC Solar
DAN WEINMAN

See us at SPI in Dallas! Booth #3237

REC Shines in 2010 Photon ModuleTest

kWh/kW

Get Tested Products from a Leading Distributor

When you buy from AEE Solar, you can be con dent you are getting the best products the industry has to o er. With 30 years of solar experience, we know which products deliver the best value for your money.

Plug Your Business into 30 Years of Solar Expertise

Trina Solar First Solar Canadian Solar BP Solar Solar-Fabrik Siliken REC Solarworld Evergreen Solarfun Isofoton Kyocera Sunways Photowa Scho Sharp

Best in test for ve out of 12 months Second highest overall 6.1% more power produced than test average

The Only Wholesale Distributor Youll Ever Need

800-777-6609
www.aeesolar.com [email protected]

Figure at left Ut alissen dignibh esse tem dipsumsan velisse zzriliquis alit lore facidui ver etum zzrillan hendignit, irit augait luptat faccum iliquatue facilit aliquis molore.

Inverters and Photovoltaic String Power Shade-Tolerant Maximum Optimal Point Tracking: Toward Maximum Harvest Efficiency and ROI
December 2010 / White Paper

by Dr. Andrew Swingler

contents column title

october & november 2011 column subtitle

Main Features
48 DIY or pro?
Justine Sanchez, Joe Schwartz & Ian Woofenden Some PV systems lend themselves more easily to DIY installations than others. Heres our guide to help you decide.

58 grid parity
Jay Tyson

On the Web
Facebook Special!
Easily browse and share our content with your Facebook friends. Enjoy special subscription offers, promotional discounts, reader comments, editors notes, and much more: facebook.com/homepower

48

58

Move over, fossil fuelsin many areas of the country, solar electricity is already economically competitive.

66 smarter water
Claire Anderson New technologies and smart strategies to save water.

76 efficient
ventilation
Neil Smith Ensure good indoor air quality with modern heat or energy recovery ventilators.

Follow us on Twitter!
Watch for bite-size article teasers, renewable energy event information, sneak peeks at upcoming coverage, subscription specials, and topical retweets: twitter.com/homepowermag

Share us everywhere!
Share an inspiring Home Power article on Facebook, Twitter, Digg, StumbleUpon, and many other services: homepower.com/articles

96 PV specs

On the Cover
Ashland, Oregon, homeowner and DIYer Jeff Heigle and professional PV installer Seaira Safady of Alternative Energy Systems pose in front of a 10 kW ground-mounted PV array.
Photo: Shawn Schreiner

Rebekah Hren All you need to know to navigate a PV module spec sheet.

Events Calendar
Search, browse, or post RE events: www.homepower.com/events

Article Database
Search and browse more than 2,000 articles in PDF: www.homepower.com/articles

76

Back Issues
Digital edition subscribers have access to the past three years back issues (18) in PDF. Subscribe to or renew the print edition for three years to get our thirdedition digital archive on DVD-ROM 143 back issues in PDF. Many back issues are also still available in print: www.homepower.com/backissues

66
home power 145 october & november 2011

These pages, left to right: Shawn Schreiner; iStockPhoto/alexsl; iStockphoto/Eric Delmar; Soler & Palau USA; SunPumps; Stephen Hren

october & november 2011 column subtitle

column title contents 96 86

37.5 in. 20 in. 20 in.
2

Up Front
8 from the crew
Home Power crew DIY PV: Then & now
STC

Photovoltaics
ations Electrical Specific
r Peak powe max power Voltage at power Current at max open circuit Voltage at at short circuit Current NOCT
2, 25C, 1.5 AM 1,000 W/m 220 watts Pmax 29.8 volts Vmp 7.39 amps Imp 36.8 volts Voc 8 amps Isc

the USA! Theyre Built in Ever Made & voltaic Modules The Best Photo

Company Inc.

General Mechanical &

65.5 in.

1.5 in.

Leads: 40 in.

14 news & notes

Kelly Davidson Battery recycling

r Peak powe max power Voltage at power Current at max open circuit Voltage at circuit nt at short Curre

C, 1.5 AM 2 800 W/m , 472 159 watts Pmax 27 volts Vmp 5.9 amps Imp Voc Isc 34 volts 6.47 amps

39.0 in.

1.5 in.

0.75 in.

Dimensions Area Thickness Weight Cells

65.5 x 39 in. 2 17.7 ft. 1.5 in. 39.6 lbs. 60 monocrystallin 6 x 6 in. e silicon

10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 0 5 10 Isc = 8 Imp = 7.39 Isc = 6.47 Imp = 5.9

STC NOCT
Peak Power = 159 W

Peak Power = 220 W

Cell dimensions Glazing Backsheet n

) Current (amps

15

Voltage

20

25

Vmp = Vmp = 29.8 27 30

Voc = 34 35

Voc = 36.8 40

Encapsulatio Frame

tempered ency, low-iron, High-transpar nt ection treatme glass with antirefl nce polyester high-performa Double-layer, Ethyl vinyl acetate aluminum Black anodized tor Wire, Tyco connec 12 AWG, PV Tyco Solarlok 3 diodes t; 20 modules/palle ft. container 75 lbs./ft.

Connectors Junction box

18 gear
Unirac Quick Mount PV

l Parameters Other Electrica

nce Power tolera Efficiency Temperature coefficients

s Bypass diode llet; Modules/pa tainer Pallets/con Design load speed Maximum wind

28 pallets/40

Percent Cell Module Pmax Voc Vmp Isc

3% 15.5% 13.5% -0.45% per C -0.35% per C

120 mph

+0.05% per C

-0.42% per C

voltage Maximum system fuse rating Maximum series

600 volts 15 amp

Ratings Certifications &

Listing class Fire safety

UL 1703 C

Warranty
power 90% rated power 80% rated hip Workmans

10 years limited 25 years limited 5 years

22 returns
Kelly Davidson Solar in Afghanistan

sorry. ny actually exist nor this compa r this PV module Power Inc. Neithe subsidiary of Home An imaginary

26 solutions
Khanti Munro Pole-mounted microinverters

30 methods
Justine Sanchez Bus bar calculations

34 mailbox
Home Power readers

104
More Features
86 off-grid office
Stephen Hren A small nonprofit meets nearly all of its office energy requirements with renewable technologies.

In Back
122 code corner
Ryan Mayfield 2011 NEC

40 ask the experts

RE industry professionals Renewable energy Q & A

112
Glazing: Baffles: 3/16 in. Lexan Two, 1 x 2 in.; 3 ft. x 6 ft. mix air with weather stripping Damper: Prevents reverse convection when collector is cool.

126 home & heart

Kathleen JarschkeSchultze The rascal rooster

131 advertisers
index

104 solar pumping

Dan Fink
Insulation: 1 3/4 in. fiberglass behind absorber Crosspieces: 1 x 2 in. lumber Backsheet:

132 back page

basics
Erika Weliczko Galvanic corrosion & PV arrays

1/2 in. plywood

The ins and outs of PV-direct water pumping.

112 DIY heating

Frame: 1 x 4 lumber

Stephen Hren
Fan: Draws air from room into collector through 4 in. duct

Air Path: Zigzags up through 1.5 in. gap

Absorber Plate: 0.04 in. aluminum, painted matte black

A step-by-step guide to building your own solar air heating collector.

www.homepower.com

Home Power (ISSN 1050-2416) is published bimonthly from offices in Phoenix, OR 97535. Periodicals postage paid at Ashland, OR, and at additional mailing offices. POSTMASTER: Send address corrections to Home Power, PO Box 520, Ashland, OR 97520.

from the crew

column subtitle first words

DIY PV

Then & Now

Add the New MagWeb to Your Magnum Panel to Monitor Your System From the Web.
Works with all Magnum Inverter/Chargers!

When we launched Home Power magazine in 1987, the modern renewable energy industry was in the early stages of its development, and bore little resemblance to the industry today. In the early 1980s, the cost of solar-electric (PV) system components had just dropped to a level that made them a possibility for remote, off-grid homesteads. Experienced PV designers and installers were few and far between. If you wanted a PV system, you probably installed it yourself. Many early adopters were resourceful and skilled back-to-the-landers who intentionally sought to hone skills for a self-reliant lifestyle beyond the reach of the utility grid. While they got systems up and running to meet their energy needs, many also learned hard lessons along the way. Fortunately, these early lowvoltage systems were fairly forgiving, and homesteaders were willing to take on the responsibility for their systems, challenges and all. About a decade ago, battery-based and batteryless grid-tied PV systems made their entrance into the industrys landscape. Their numbers quickly eclipsed off-grid systems, with an enormous market of grid-connected homes and owners with a wide variety of motivations for purchasing PV systems. As the market developed, some of the early adopters began installing systems professionallythe experience they gained installing their own and neighbors systems offered livelihood opportunities. As the demand grew, mainstream electricians also began to enter the industry. Today, most systems are professionally installeda quick Internet search will uncover multiple PV installation contractors in most areas of the United States. In some respects, modern batteryless systems are simpler than their off-grid predecessors. But the technical, regulatory, and safety issues are more significant. While very few of the original off-grid systems received permits, even in the early stages of the grid-tied market, incentive programs and authorities required permitted, inspected, code-compliant systems, and often required that licensed electricians install them. The demographics of individuals buying PV systems have changed, too. Todays grid-tied PV system owners may be bankers, doctors, teachers, and many others with no construction experience who hire a solar contractor to achieve their solar goals. Both DIY and professionally installed systems are parts of our modern industry, and theres an appropriate place for each. See the article on page 48 for perspectives on whats best for moving your home into its solar future, by doing it yourself or hiring a pro. Joe Schwartz, for the Home Power crew

Think About It...

Nature provides a free lunch, but only if we control our appetites.
William Ruckelshaus, Business Week, June 18, 1990

www.magnumenergy.com

home power 145 october & november 2011

Its that easy.

The Magnum Panel (MP) system from Magnum Energy makes ordering and installing inverters and balance of system equipment easy and convenient.

Easy to install:
With panels pre-wired and all connections front-mounted, including AC and DC breakers, the MP is easy to install, saving labor costs.

Easy to handle your power needs:

Depending on the system, the 60A or 125A bypass breaker and 500A or 1000A DC shunt easily handles your total system power.

Easy to expand:
Start with just one enclosure and one inverter and, depending on your MP Panel model, easily expand to two, three, or four inverters in the future using MPX Extensions. Visit us at Solar Power 2011, Booth #451 to see whats new. Youll get a charge out of it!

Easy to monitor:
Monitor your Magnum inverters and accessories easily on the web with the MagWeb. Using your always on Internet connection, the MagWeb makes live and historical conditions available to you through your web browser.

To learn more about the MP system, the MagWeb, and other Magnum products visit www.magnumenergy.com

contact us
Publishers Executive Editor & CEO Managing Editor Art Director Senior Editors Technical Editors Associate Editor Graphic Artist Building Technology Editor Solar Thermal Editor Transportation Editor Columnists Advertising Manager Advertising Director Chief Information Officer Operations Director Data Manager Customer Service & Fulfillment Joe Schwartz Claire Anderson Ben Root

Home Powerindependently published since 1987

Richard & Karen Perez

Who do you trust

Michael Welch, Ian Woofenden Justine Sanchez Erika Weliczko Kelly Davidson Dave Emrich Rachel Connor Chuck Marken Bradley Berman Kathleen Jarschke-Schultze Ryan Mayfield Connie Said Kim Bowker Rick Germany Scott Russell Doug Puffer Jacie Gray, Shannon Ryan

when the grid goes down?

OutBack Power. Setting the industry standard for reliability since 2001.

Home Power magazine PO Box 520 Ashland, Oregon 97520 USA

homepower.com facebook.com/homepower Subscriptions

To subscribe, renew, change, or inquire about a subscription: 800-707-6585 or 541-512-0201 [email protected] www.homepower.com/subscribe

twitter.com/homepowermag Ask the Experts

To have your technical questions considered for publication, send them to: [email protected]

Letters to the Editor

E-mail your comments and suggestions to us at: [email protected] or write to the address above.

Back Issues
Many of our back issues are available in print and/ or online in Adobe PDF. Our first 131 issues are also compiled on DVD-ROM. More information at: www.homepower.com Order online or by phone: 800-707-6585 or 541-512-0201

Marketing
Promotional opportunities and offers: [email protected]

Advertising
For inquiries and information related to advertising in Home Power or on www.homepower.com: Western States: [email protected] 541-326-5773 Eastern States: [email protected] 541-858-1791 www.homepower.com/advertising

Submissions
For inquiries and information related to editorial submissions, write to us at: [email protected] www.homepower.com/writing

Website
www.homepower.com Send your comments regarding the site to: [email protected]

Phone: (360) 435.6030 www.outbackpower.com

2011 Home Power Inc. All rights reserved. Contents may not be reprinted or otherwise reproduced without written permission. While Home Power magazine strives to publish only safe and accurate content, we assume no responsibility or liability for the use of this information. Interior paper is made from 85%100% recycled material, including 20%30% postconsumer waste.

home power 145 october & november 2011

OutBack Power:

Weve got your back

The new Radian Series is an integrated power appliance that does it all
Sure, our newest inverter/charger is a powerful solution. From the sunniest day to the storm that knocks out the grid for a week or more this system is built to carry the load. At the same time, its as easy to live with as any home appliance. Easy to install. Seamless operation. Hot coffee and cold beerits as simple as that. Revolutionary on-grid/off-grid integrated design 8000 Watts of continuous power, flexible design for systems from 8 to 80kW Easily powers both sensitive electronics and the largest surge loads Simple to design, install, and maintain Back-up power lets you stay off-grid for extended periods High reliability and dual power modules minimize downtime risk

For more information:

Scan with your smartphone for more information. Text scan to 43588 to install ScanLife.

Main Office: 5917 195th Street NE, #7, Arlington, WA 98223 USA Phone: (360) 435.6030 Fax: (360) 435.6019 www.outbackpower.com

as tough as they come

Our solar modules can stand up to a lot of punishment. In fact, they are engineered to be particularly robust and durable. This has not only been proven through the long-term high yields of our clients solar systems, but also through numerous tests. The independent German consumer protection society Stiftung Warentest gave us their top marks; and ko-Test rated us as very good. Call 1-866-411-2536 for more information.
Top Grade

GOOD

Photovoltaic modules aleo S_18

Tested: 13 solar modules Issue 5/2006

very good
Issue 04/2010

news & notes column title

renewable energy in the spotlight column subtitle

Exported Battery Recycling

Eventually, all lead-acid batteries will come to the end of their life and need to be recycled. The questions are: How, where, and by whom?
While the export of used lead-acid batteries (ULABs) from the United States is legal and a fairly common practice, this practice may be contributing to lead contamination and exposures in Mexico and other places around the world. A recent report prepared by San Francisco-based NGO Occupational Knowledge International (OK International) and Mexico City-based NGO Fronteras Comunes found that increasing quantities of ULABs are being exported from the United States to Mexico for recycling, and contributing to increased pollution and worker health hazards. The reports release came on the heels of lead battery and lead recycling plant shutdowns in China following cases of widespread lead poisoning in local communities. As part of a crackdown on 18 polluting industries, the Chinese government aims to shut down 585,500 tons of illegal leadsmelting capacity this year. The findings show that, in 2010, 75% of all ULABs and lead scrap exported by the United States was shipped to lead battery manufacturers and recyclers in Mexico, up from 39% in 2008. According to the report, U.S. International Trade Commission data indicates that approximately 261,000 tons of used lead batteriesequivalent to 12% of all used leadacid batteries generated in the United Stateswere exported to Mexico in 2010. This quantity represents a 112% increase over 2009. But the numbers may be even higher, says Perry Gottesfeld, executive director of OK International. There is no Mexican or U.S. system to track or inspect individual shipments across the border. We have seen international shipments that have had false labeling on them. Containers have been labeled as plastic, when theyre lead batteries. Its definitely possible that shipments slip through customs. A major issue, Gottesfeld says, is that there is no waste manifest system to monitor the ultimate destination of ULABs that enter into Mexico from the United States, and some exports are diverted to unlicensed recycling facilitiesor to other countries. The report cites cases in which authorities in Hong Kong have returned mislabeled, leaking containers of ULABs sent from Pacific Ocean ports in Mexico. Thought Mexico has a number of laws and regulations addressing ULABs, lead pollution, hazardous waste, and recycling practices, the report notes that there are no explicit requirements that monitor employee exposures or remove workers from high-exposure areas. According to the report, the maximum permissible exposure limit for lead in air is 10 times higher in Mexico than in the United States (1.5 vs. 0.15 g/m), and the occupational airborne exposure limit in Mexico is three times higher than in the United States (150 vs. 50 g/m). And, in comparison of similar-sized lead plants in both countries, the researchers found that emissions from plants in Mexico are approximately 20 times higher than those from plants of similar capacity in the United States. OK International and Fronteras Comunes are calling for government intervention under the North American Free Trade Agreement (NAFTA) framework to close unauthorized plants and bring Mexican companies into compliance. Mark Thorsby, executive vice president of Battery Council International (BCI), a Chicago-based trade group, maintains that U.S. manufacturers uphold the same smelting controls in Mexico as in the United States, saying that U.S. manufacturers are not shipping used batteries to Mexico to get around environmental regulations. The main drivers for shipping the batteries south, Thorsby says, are lower labor and operational costs.

Recycling lead in a lead-acid battery recovery facility.

Courtesy The National Institute for Occupational Safety and Health

14

home power 145 october & november 2011

renewable energy in the spotlight column subtitle

news & notes column title

Despite the fact that there is no federal law compelling manufacturers to recycle battery lead, nearly 98% of battery lead is recycled and reused in new batteriesthe highest recycling rate of any raw material in the United States, Thorsby adds. It is estimated that a typical new lead-acid battery contains 60% to 80% recycled lead and plastic. The rising price of virgin (mined) lead in recent years is driving the high recycling rate, says Michael Fraley, a product and process engineer at Crown Battery Manufacturing Company in Fremont, Ohio. It comes down to dollars and cents, Fraley says. As the price of virgin lead has climbed higher and higher, scrap lead has become more and more valuable, motivating manufacturers to be more diligent about collecting used batteries and controlling the costs associated with lead smelting and recycling. Lead prices have teetered around $1.20 per pound in recent months. Scrap lead costs about 70 cents per pound or less, depending on transport, labor, and conversion charges. With each battery holding 20 to 40 pounds of lead, the savings per battery can be substantial, Fraley says. The massive increase in spent lead-acid battery (SLAB) exports to Mexico and the appalling lack of government oversight indicate a disaster waiting to happen, says Diane L. Cullo, director of the U.S. advocacy group SLAB Watchdog. Sending used lead-acid batteries to Mexico for recycling without any regard for the health of workers, the community, or the environment simply because it is cheaper is unconscionable and must stop immediately, she says. More than 12 million people in the developing world are adversely affected by lead contamination from processing lead-acid batteries, according to the Blacksmith Institute, an international nonprofit working to solve pollution problems. If inhaled or ingested, lead can damage the nervous system and cause brain damageespecially in children, whose bodies are still developing. Lead-acid batteries, particularly the common wet cells, also contain electrolyte with significant amounts of sulfuric acida highly corrosive liquid that can burn the skin. In the United States, lead-acid batteries are included under the EPAs Universal Waste laws, which provide collection requirements for certain hazardous wastes including batteries. Currently, battery recycling legislation and mandatory takeback programs exist in 45 states. Moving forward, proposed legislation aims to limit the export of ULABs and create domestic recycling jobs. Rep. Gene Green (D-TX) and Rep. Mike Thompson (DCA) introduced the Responsible Electronics Recycling Act earlier this year. The legislation would prohibit the export of electronic waste, including lead-acid batteries, to countries that are not members of the European Union or the Organization for Economic Cooperation and Development (OECD). The fate of the bill remains uncertain, as it awaits committee review, but major electronics companies have

Behind Recycling
Recycling lead-acid batteries is a fairly straightforward process. A hammer mill pulverizes the whole batteries into smaller pieces. In a vat, the lead sinks to the bottom, and the plastic case pieces float. The plastic is scooped off, washed, and dried, then melted and extruded into pellets to be made into more battery cases. The liquid is drained off and is usually neutralized with the addition of a base, but sometimes can be turned into more electrolyte. The neutralized water is further processed and released into a wastewater treatment plant. After testing, it can be released into the environment. Another way of treating the acid turns it into sodium sulfate, which is used in laundry detergent or glass and textile manufacturing. The lead is melted in a smelting furnace and poured into ingots, where the impurities float to the top and are removed. The lead is then is shipped back to battery manufacturers for making into new batteries.

backed the legislation. The bill also won support from 29 recyclers representing 74 recycling operations in 34 states. Though hailed as a step in the right direction by the Electronics TakeBack Coalition and the Natural Resources Defense Council, the bill would not preclude ULAB exportation to Mexico, which is one of the 34 member countries of the OECD. However, it would stop exports to China, which is not a member of the OECD. If passed, the legislation would fill a much-talkedabout gap in a national e-waste stewardship plan that was released in July by an interagency task forcechaired by the U.S. Environmental Protection Agency, the General Services Administration, and the White House Council on Environmental Quality. The plan, which provides recommendations for the handling of e-waste coming from federal agencies, received mixed reviews from advocacy groups for failing to take a hard line on e-waste exporting and address foreign battery recycling. One high point of the plan is federal support for U.S. ratification of the Basel Convention, an international treaty intended to prohibit the transfer of hazardous waste from developed to less-developed nations. The plan falls short of outlining any concrete steps toward doing so, according to a spokesperson for Basel Action Network, an American watchdog group that has sought to curb the export of toxic electronic waste from the United States. Of the 176 parties of the convention, the United States, Afghanistan, and Haiti are the only countries that have not ratified the treaty since it was brought into force in 1992. The Senate provided its advice and consent for ratification in 1992, but implementing legislation has not been passed. Kelly Davidson

www.homepower.com

15

TrOjanS new IndustrIal lIne

When failure is not an option and reliable power is absolutely essential - youre in Trojan territory. Introducing Trojans industrial line - the newest addition to our lineage of highquality batteries. Specifically engineered to support renewable energy systems with large daily loads that cycle regularly, the industrial line delivers high-capacity power when you need it the most. Exceptionally dependable and powerful, the industrial line delivers 1,500 cycles at 80% depth-of-discharge and unmatched performance in your grid-tied or off-grid PV system. Trojans proprietary deep-cycle technology and over 85 years of battery know how make the industrial line the most reliable battery on the market. Backed by specialized technical support teams and world-class warranty Trojan means reliability.
TYPE
IND9-6V IND13-6V IND17-6V IND23-4V IND29-4V

CAPACITY Amp-Hours (AH) 5-Hr Rate

355 533 711 977 1245

20-Hr Rate
445 673 897 1233 1570

100-Hr Rate
545 820 1090 1500 1910

VOLTAGE
6 VOLT 6 VOLT 6 VOLT 4 VOLT 4 VOLT

Available worldwide. For more information, call (800) 4236569, +1 (562) 2363000 or visit us at TrojanBatteryRE.com Off Grid Grid Tied Backup pOwer rural elecTrificaTiOn induSTrial SmarT Grid

gear column title

cutting-edge equipment & tools column subtitle

Unirac Flat Flashing

Unirac (www.unirac.com) now offers its Flat Flashing for asphalt composition shingle roofs. This flashing solution consists of a 2- by 2-inch compression plate and 8- by 12-inch flashing with preinstalled gasket to seal the lagscrew penetration. Flat Flashing provides the mounting attachment (i.e., L-foot) with a flat surface to sit on, reducing installation time by allowing the flashing, compression plate, and mounting attachment to be installed along with the lag bolt. The flashing is compatible with all Unirac roof mounts: SolarMount, SolarMount I, SunFrame, and tilt-up arrays, and was tested to withstand up to 70 feet of standing water.

Courtesy Unirac

Sp

ec

ial

Great people, great products, great prices

Inverters
3kW - 300kW available Ontario made Dual MPPT PV input Reliable, 97% Efficient Easy to install and use

De

al

er

Pr

ici

ng

6 kW Scirocco
Variable pitch, low RPM MPPT inverter Quiet, highly efficient European made Reliable, affordable

Were here to help you, just give us a call!

US / Canada distributor of Power-One inverters and Eoltec wind turbines 18

home power 145 october & november 2011

www.Solacity.com/hp Call Toll Free 877.787.9748

column title

cutting-edge equipment & tools column subtitle

gear

Quick Mount PV 3 New Mounts

Quick Mount PV (www.quickmountpv.com) recently released three new products: the New Roof Composition Mount, the Universal Tile Mount, and the Low-Slope Mount. The New Roof Composition Mount is designed to be installed by a roofing contractor before the roofing material is installed (see pages 98 & 99 of HP144). It is available in three finishes: aluminum mill, clear anodized, and bronze anodized. The Universal Tile Mount is a similar product for use on existing or new tile roofs. It features two flashings: a subflashing for the roof deck and a top unit for the tile level. The top flashing is malleable and can conform to either curved tile or flat tile. It replaces the companys existing Curved Tile Mount. The Low-Slope Mount can integrate into existing or new singleply membrane and built-up asphalt commercial roofs. All three products utilize the companys new Qbase for roof attachment points. The aluminum-cast base accepts standoffs as tall as 9 inches and provides up to four attachment points to the roofing substrate or structure. Justine Sanchez

Courtesy Quick Mount PV

solar trackers
HORIZONTAL LINEAR AXIS

Get 25% more power from your system with this extremely durable, low-profile horizontal tracker. Not only can it blend into the environment, but its also easy to assemble. The HZLA tracks from 45 to 45 and can mount up to 4 kW per tracker.

More power. More choices. Better engineering.

SEASONAL ADJUSTABLE RAC K

This low-cost alternative to a tracker or fixed ground mount gives you the ability to easily optimize your arrays tilt to compensate for the suns seasonal changes. With up to 4 kW capacity, it is quickly adjustable from flat to 60 by one person using a battery-operated drill.

Solar trackers are never a one-design-fits-all solution. For more than 20 years, Array Technologies has been designing high quality, low maintenance tracking and racking systems for residential, commercial and utility-scale projects. From our popular Wattsun and HZLA single-axis, dual-axis and horizontal linear-axis trackers, to our innovative, low-cost seasonal adjustable racks, we have the perfect solution for your project.

A D I V I S I O N O F A R R AY T E C H N O L O G I E S

wattsun.com

505.881.7567

[email protected]

www.homepower.com

19

/ Battery Charging Systems / Welding Technology / Solar Electronics

L FRONIUS C L . S E E TH E OMMERCIA INTERNATIONAL . GO C OW E R 2327 AT SOL AR P all C / Booth

11 / Dallas / / Oct 1720 20 H

/ Up to 15 power modules using Fronius MIXTM technology achieve great things for the Fronius CL central inverter series. Individual power racks are switched on and off fully automatically depending on the irradiance level. This optimizes capacity utilization and maximizes earnings in any weather. But thats not all: the Fronius CL central inverter series for systems up to several hundred kilowatts also ensures extreme reliability and a long service life. For more information, go to www.fronius-usa.com

returns column title

giving back with renewables column subtitle

Microhydro Brings Light to Remote Afghan Villages

In Panjshir Province, about five hours north of Afghanistans capital city of Kabul, families in the remote village of Daste Riwat now have access to clean, renewable energythanks to a microhydro plant built with support from the U.S. Army Corps of Engineers (USACE). The people here are very happy about the electricity, says Malay Ghalam Galani, the Daste Riwat school religious elder who donated some of his land to accommodate the plant. It has brought brightness into the home, and this is a very good thing. The Daste Riwat plant was installed in January 2009 as part of an USACE project to construct 105 microhydro units in seven of 34 Afghan provincesone plant per village. The 130-kilowatt system was among the largest completed; the average system is about 10 kW. The last unit, in Parwan Province, is still under construction and awaiting additional funding for distribution lines. The project was made possible by the Commanders Emergency Response Program, which enables U.S. military
One of 15 skilled Afghan workers employed by Remote Hydrolight in Afghanistan builds a turbine crossflow at a workshop in Kabul.

commanders in Afghanistan to fund rebuilding and reconstruction projects. Projects like these gain the trust of the Afghan government and promote civil infrastructure improvements that positively impact villagers lives, says U.S. Navy Lieutenant Commander Joel VanEssen, an officer assigned to the USACE as part of the U.S. militarys Afghanistan Pakistan Hands Program, which aims to build partnerships with local communities. Access to microhydro power has eased the villages dependence on kerosene lanterns, diesel generators, and wood-burning stoves, which are health and environmental hazards. Microhydro installer Owen Schumacher, who has lived and worked in Kabul for the past 18 years, completed the initial survey work and presented the idea to USACE back in 2005. I was here when there was no electricity, and I know how depressing it can be, says the South Dakota native, who has been installing and developing microhydro power systems in Afghanistan for 15 years. Schumacher first moved to Afghanistan to work for a solar energy organization, but after a few years, he saw the potential for hydro energy. The high mountains receive snow that slowly melts throughout the year, forming streams and rivers. The many springs that flow down the hillsides make good sources for year-round hydro-power. Most villages are close to a stream or river and already use the water to power traditional stone water mills, so the concept of hydropower is not completely new to them, he says. Since then, Schumacher has developed and tested multiple prototype systemsincluding a high-efficiency cross-flow turbine that was tested at the Waterpower Laboratory of the Norwegian University of Science and Technology. In an effort to grow support for microhydro projects, he also held workshops to train Afghans how to manufacture, install, and repair these systems. In 2006, Schumachers companyRemote HydroLight, a for-profit business that builds community-owned microhydropower plants in remote areas of Afghanistan was chosen by the USACE to share the project contract with Engineering Associates, a microhydro power installation company in Kabul. For the USACE project, Schumacher and his crew of 15 Afghan workers oversaw the installation of 97 units, as well as designed prototypes and trained employees of private shops in Kabul to build the turbines and electrical boxes. All of the components, with the exception of imported alternators, were fabricated locally.

22

home power 145 october & november 2011

Courtesy Master Sgt. Michael OConnor

giving back with renewables column subtitle

column title returns

Buy-in on a project by local elders is vital to the projects success, and village cooperation is key to a plants future, VanEssen says. We ask them for their opinion on where things should be, Schumacher says. By contributing their labor, they feel they own the plant when it is all built, and it is their plant. Once a project was approved, the community was responsible for providing the labor for the installation and transporting all of the equipment to its site, which often meant long hours hauling parts on mules through the mountains on footpaths. When necessary, the community also built new channel or reinforced an existing canal from the nearest water sourcea considerable amount of work that often involved cutting into the hillside and erecting several hundred feet of stone wall. Remote HydroLight provided Afghan workers in the village of Daste Riwat, Panjshir Province, conduct training on installers, who worked side-by-side how to maintain the forebay. with the village laborers. Typically, one installer managed multiple installations in a watershed area, walking between the villages to check on the communities progress and give (such as a hot pot, water heater, or flat-bread cooker), and one instructions as needed. Some smaller systems were installed for all the lights and other regular sockets (for items such as in as little as three weeks, while others took close to a year to lights, televisions, washing machines, and computers). complete, due to discord in the village. To ensure everyone is charged accurately for usage, Most of the plants are sized to provide power for lights meters were installed in each compound. Every two months, and small electronics, such as televisions, radios, and battery the elders have a meter reader who writes down the amount chargers. The average village family needs only about 60 W used and then collects usage fees. The average family pays to 100 W of power for two or three 20-watt fluorescent about $2.70 per month, which is used to pay the village lightbulbs. In most cases, the operator turns on the plant operators and provide for any maintenance expenses, such as from sunset to sunrise because the water is used for irrigation belts or grease. during the daylight hours. Having seen how this project has transformed his village, After a plant is operational, the locals monitor the energy Galani says he would like to see more projects like this that usage, keep the canal clean, and lubricate the turbine bearings benefit his people. regularly. Schumachers crew returns to the site to handle With the USACE project complete, Schumacher and his major problems as necessary. Otherwise, villagers can bring crew have moved on to other microhydro installations in the broken parts to his shop or one of the private shops where his region. They are currently installing four prototype Kaplan trained technicians can repair the equipment. Maintenance turbines in the Nangarhar Province near Jalalabad. and repair costs are covered by nominal monthly usage Right now, it is getting more difficult to work in many fees that are collected: 20 to 30 cents for each light (or the areas of the country due to poor security. The Taliban are equivalenta TV equals three lights) per household. For more organized and have sent cells all over this land, but larger systems, watt-hour meters track each households we will continue to do what we can, he says. The Afghan consumption. people are hard workers and have been very eager to help The Daste Riwat plantwith two 65-kilowatt turbines install our small hydro plants. These types of projects can relies on an 8-foot-wide, 1-mile-long canal off the Panjshir River, flourish in peaceful provinces and bring not only work for the and runs around the clock. The electricity generated is people, but power too. distributed through a mini-grid that feeds the villages 110 Michael OConnor, with Kelly Davidson compounds, which house two or three families each. Each compound is equipped with two fuses: one for a heavy-duty socket in the kitchen for a high-watt appliance
Courtesy Master Sgt. Michael OConnor

www.homepower.com

23

Aim High
Renewable Energy Solutions Renewable Energy Solutions
TM

At Power-One, we aim high so you can too.

TM

You can choose from our wide range of popular Aurora products from small residential string inverters to large commercial central inverters, including the Aurora 5000/6000kW UNO-single phase, 10.0/12.0kW TRIO-three phase and 250/300kW PLUS Central inverters.

Enjoy the maximum returns from your investment.

www.power-one.com

Runs On The Sun

Cirrex Solar

Cirrex Solar Water Heating Systems from A. O. Smith

The Cirrex is more than just a solar water heaterits the ultimate solar thermal solution. High efficiency ratings, long life, and reduced carbon emissions are just a few things that make it an irresistible choice for environmentally conscious homeowners. With utility costs for water heating reduced up to 70%, the Cirrex is a wise choice for everyone. The time has never been better to invest in renewable energy. Demonstrate your own green initiative today with Cirrex.
n

Provides up to 70% of energy needed for water heating directly from the sun 16 solar water heating systemsone, two, or three collector configurations All solar water heating systems are SRCC certified OG-300 Solar Energy Factor (SEF) ratings up to 10.1 Eligible for federal tax credit of 30% of the total installed cost
Scan this code for more info and to view a video about the Cirrex.

n n

www.hotwater.com

solutions column title

ingenuity in renewable energy column subtitle

Pole-Mounted Microinverters
Siting an array can often go well beyond shade mitigation. Accounting for roof size, orientation, and tilt; considering seasonal weather patterns (such as morning fog); meeting aesthetic criteria; avoiding otherwise usable space; and, of course, pleasing the customer are all considerations. An installers lack of attention to the bigger picture can result in poor system performanceand an unsatisfied customer. Thankfully, new products and a little creativity are increasing design flexibility. At the Letendre residence in Middletown Springs, Vermont, it became clear that a unique solution was required. The straw bale homes upper south-facing roof was already occupied by a large solar thermal system used for in-floor radiant heating. A lower south-facing roof was available, but would be subject to excessive snow and ice build-up from the upper roof. The front and back lawns were not considered due to aesthetic concerns and existing land use, i.e., parking, play space for children, etc. The remaining available yard space was a 10- by 20-foot spot west of the home. The space was large enough to accommodate the specified system size on a pole mount, but had another challengeit would incur some partial morning and afternoon shade. The eastern half of the array would be shaded until around 11 a.m. and the lower fourth of the array would be shaded from noon to 2 p.m. during two winter months. On the west side, about one-fourth of the array would be shaded after 4 p.m. The annual solar access for the array is estimated at 80%. Thankfully, microinverter technology could help address this, since

Courtesy Khanti Munro (3)

Overview
Project name: Letendre residence System type: Batteryless grid-tied PV Installer: Khanti Munro, Solarise Services Commissioned: September 2010 State: Vermont; 43.48 latitude Solar resource: 4.61 average daily peak sunhours System capacity: 2.38 kW STC Average annual production: 2,500 AC kWh (estimated) Average annual utility bill offset: 83%

Equipment Specifications
Number of modules: 14 PV modules: Sharp NE-170U1 Module rating: 170 W STC Number of inverters: 14 Inverters: Enphase M190, 240 VAC Rated output: 190 W Array installation: Pole mount, DP&W TPM-14 Array azimuth: True south (194) Tilt angle: Seasonally adjustable

26

home power 145 october & november 2011

ingenuity in renewable energy

solutions

one microinverter is paired with each module. Because each module operates independently, shading effects on one module will not affect the whole string or array. However, microinverters are commonly designed to mount to the slotted rails of roof-mounted PV racks. Custommounting the micros to a pole-mounted array, although not difficult, added to the installation time and created some new challenges. Although the rack manufacturer was not willing to pre-drill the inverter mounting holes, they did confirm that drilling two holes per inverter in the rack would not void the warranty or cause any structural issues. To minimize the aesthetic impact of the array underside, extra time was taken to ensure that the inverters were mounted under the modules in a neat, organized manner. Wire management was also difficult given the long AC inverter cables and the under-array exposure. A combination of wire clips and rubber splicing tape with stainless steel zip-ties were used to organize the cables, and very careful coiling of excess wire on the top sides of rails helped conceal it. Besides meeting the customers siting requirements, the installation provided better airflow around the inverters and modules, helping them operate cooler and more efficiently. With this design, the roof peaks morning shadows and the afternoon tree shadows now only affect a portion of the array as opposed to all of it if we had used a string inverter. Khanti Munro Solarise Services

0, 2011 October 17-2 s, Texas Dalla r: 350 booth numbe

www.homepower.com

27

we sell it, we teach it, we live it

and love it!

Steves family is making renewable do-able, are you?

altE customer Steve and his family have their entire roof covered in thin-film solar electric modules that produce enough electricity to completely charge their new Tesla electric roadster in Londonderry, NH!

Great Gear, Great Prices!

New !

Your Solar Home Solar Air Heaters starting at: $1,208

Kyocera 135 Watt Solar Panel starting at: $363

Air40 Wind Turbine Lifetime Warranty only: $895

Blue Sky MPPT Solar Charge Controllers starting at: $169

Xantrex C40 Solar Charge Controllers only $124

Call us at 800.320.9458 or visit us online at www.altEstore.com

Get an Extra Discount! Mention this code: HP145 when you order today!

AltE Store is the Do-It-Yourselfers supplier of renewable energy gear. We provide you the products, tools, education, expertise and the technical service you need to safely and successfully put together your own system. Join our fun and enthusiastic community of DIYers today!

making renewable do-able for over 10 years!

Call us at 800.320.9458 or 978.562.5858 or visit us online at www.altEstore.com

Some of the brands we proudly represent:

STELLAR
PERFORMANCE
Heliodyne has a broad range of single tank OG-300 Certified systems.

I trust Heliodynes solar hot water products because I can depend on them all to deliver consistent, stellar performance.

Installers are saying great things about us.

Weve been installing solar water heating with Heliodyne for over 34 years. Their GOBI collector is simple to install and delivers reliable, long-term performance. We choose Heliodyne not only because of the exceptional products, but because of their great customer service as well. Heliodyne is one of the few companies I work with that can deliver on both product and service.
Martin Morehouse, Solar Thermal Dept. Manager, Sun Light & Power

CALL 1.888.878.8750 TO FIND OUT MORE, OR GO ONLINE

Heliodyne, Inc. 4910 Seaport Avenue Richmond, CA 94804 T: 1.888.878.8750 or 510.237.9614 F: 510.237.7018 Information & Support: [email protected] Sales Inquiries: [email protected] www.heliodyne.com

EXCELLENCE BY DESIGN

methods

renewable energy tips & tricks

Bus Bar Calculations

Is Your Service Panel Large Enough for Your Inverter?
Grid-tied PV systems supply solar electricity to your home, and the inverters AC output must be connected to the household wiring. This is usually accomplished by connecting the inverter output so that it back-feeds a circuit breaker in your main service panel (called a load-side connection). However, in most cases, the service panel was in place before the PV system was considered, and only the grid input into the home was considered. So when planning your PV system interconnection, make sure your connection does not violate National Electrical Code (NEC) requirements. Backfeeding a circuit breaker with a PV systems output adds a second source feeding the bus bars in your service panel. A service panels bus bars are rated to handle only up to a certain amperage. If the service panel/bus bars are not large enough, then bus bar overheating is possible. The bus bars in the service panel must be adequately protected, and its the supply circuit breakers that limit the overall current on those bus bars. So along with the service panel/bus bar rating, the rating of the grid and inverter circuit breakers must be considered. The NEC stipulates that the sum of the circuit breaker ratings feeding a bus bar can amount to 120% of the bus bar rating, but no higher. For example, if we have a 100amp service panel, the bus bars are rated to handle 100 A. The sum of both of the circuit breakers (from the grid and from the inverter) can be no more than 120 A (100 A 1.2 = 120 A). If we have a 100 A main breaker, then we are left

Load-Side Connection

To Utility Grid

kWh Meter

Main Breaker: 100 A

From PV System: 240 VAC inverter output, 3,840 W (16 A)

Breaker: 20 A

AC Service Entrance: 100 A service, to 120/240 VAC loads

with a maximum inverter output breaker rating of 20 A. Additionally, because in this example we are exceeding the service panels rating, the NEC requires locating the inverters breaker on the opposite end of the service panel from the grids main breaker. This ensures that the current coming in from the grid and the PV system are distributed across the service panel bus bars, rather than concentrated on one area. The inverters output circuit breaker is sized so that the inverters output is no more than 80% of the circuit breakers rating. If our maximum inverter breaker is rated at 20 A, that means that the inverter output is limited to 16 A (20 A 0.8 = 16 A). If the inverter output is 240 VAC, our maximum allowed inverter output is 3,840 watts (240 VAC 16 A). You will not find an inverter rated at this exact value, so you will need to figure out what models will work. For this example, a 3,800 W inverter is appropriate; a 4,000 W model is not. If the service panel is not large enough to accommodate the inverter, there are a few options. We can limit the PV system size, and the breaker, to fit within the limitations of the service panel. We can replace the service panel with a larger-amp unit. We can downsize the main breaker (although a household load analysis should be done to make sure that there wont be nuisance tripping of that breaker during normal conditions). Or we can connect the PV system via a supply-side connection (see Code Corner 135 for more information). Justine Sanchez

30

Courtesy Khanti Munro

home power 145 october & november 2011

Big wave surfer. SolarWorld Authorized Installer.

Work-life balance achieved.

Kohl Christensen, Oahu, Hawaii

I have been traveling to remote locations on surf trips for years and now, after becoming a solar contractor and teaming up with SolarWorld, it feels really good to be able to travel back to these spots and share some of my knowledge... I am glad I can help. Partnering with Americas largest solar panel manufacturer allows Kohl to chase big waves and spread his passion for solar. Find out how becoming a SolarWorld Authorized Installer can help you achieve a work-life balance at

SolarWorld.com.

Want to know the secret to stress-free PV installations?

Choose PV Powered string inverters from Advanced Energy.
As an installer of residential solar energy systems, your business and your reputation depend on getting everything right. So why take a chance on an unproven inverter? With PV Powered string inverters from Advanced Energy, you know youre getting reliable, time-tested, and easy-to-install PV inverter solutions backed by a 10-year warranty and a best-in-class service team. So make the smart choice with PV Powered string inverters. Thats the secret.
www.advanced-energy.com/string [email protected] | 877.312.3832

Advanced Energy, Solaron, and PV Powered are U.S. registered trademarks or service marks of Advanced Energy Industries, Inc.

SI N CE 19 9 8

OV ER 17, 0 0 0 S YS T EMS S O LD

15 0 + Y E AR S CO M B I N ED S O L AR E XPER I EN CE

30MW D ELI V ER ED

Installers, got leads?

NABCEP Certified
PV Installers on Staff

SOLAR PANELS

DESIGN

1,800+ products online Line Drawing Services Engineering Services Installation Support

SCHOTT SOLAR

235 Watt Panel

CANADIAN SOLAR

230 Watt Panel

235 Watt Panel

KYOCERA

Installation Experience from 1kW to 1MW EE-98 & GB-98 Licenses Authors of Complete Idiots Guide to Solar Power for your Home

INVERTERS

EXPERIENCE

ENPHASE

Micro-Inverters

FRONIUS

Inverters

SMA

Inverters

SERVICE
96% of calls answered within 3 rings 95% of orders ship within 48 hours
SATCON

Commercial

PVPOWERED

Commercial

SOLECTRIA

Commercial

10,000 homeowners per month visit our website. Let us direct them to you.
Pictured: 1MW carport in Albuquerque, NM designed and implemented by Affordable Solar

Learn and buy online at , or call:

1.888.736.5792
4840 Pan American Frontage Rd N | Albuquerque, NM 87109

Meet Aaron. Brewmeister. Grid-tie guru. (Knows not to mix the two)
Physicist, beerologist, and walking NEC code reference, Aaron is our go-to guy on grid-tie. Need a formula for a good ale or a knowledgeable person to walk you through a tough technical challenge? Call Aaron.

7am 6pm MST T

| USA

mailbox column title

letters from readers column subtitle

The Beijing city government restricts internal combustion engines for two-wheeled vehicles to 150 cc; three-wheeled vehicles are restricted to 750 cc. These limits, plus the speed of city traffic, make EVs equivalent to gasoline vehicles for hauling. In the center of the city, gas-powered motorcycles, scooters, and mopeds are greatly outnumbered by electric vehicles and even by pedal power. From the look of many of the electrics, this is neither new nor emerging technology in China.
Courtesy Robert Boardman

to scan them and find that the only vehicle with more than two wheels mentioned is an electric skateboard, which is not very practical for a rural commute. I live in rural Michigan, with a 25-mile trip to town, one way, and would like to get a higher fuel economy vehicle, which is difficult given I already drive a Toyota Scion xA. Driving a two-wheeled vehicle on freeways and rural roads frequented by gravel trucks through a Michigan winter is suicidal. While there are a lot of things I will do for my planet, risking my life in that way isnt one of them. I need an affordable, lightweight, but stable and ultra energy-efficient mode of transportation that can keep up with, and even pass, cars and truckseven under slippery conditions. Yet the last time I searched the Web for electric trikes, they all seemed to cost twice what my car does despite being much smaller and with one less wheel. If I had that much cash, Id have gotten a hybrid car instead of my Scion. While I love the efficiency and practicality of my compact hatchback car, what is affordable at $3 per gallon is not at $6 per gallon, and Im trying to think ahead and kick the fossil-fuel habit while we still have a livable planet.

Shortly after I came back from a few weeks in Beijing, China, I received HP144. I was particularly interested in the cover story about electric motorcycles. I estimate that there are hundreds of thousands, probably millions, of electric bicycles, tricycles, mopeds, and motorcycles in the city of Beijing. Two- and three-wheeled vehicles are extremely popular. They are used for commuting and for commercial delivery for everything from small packages to home appliances. They generate no fumes and they do not make noise, except for their horns.

Who is More Developed?

I remind readers that Beijing is the capital of the country with the second largest economy in the worlda large, sprawling city of about 23 million people. It is good to read of the growing market for electric vehicles in North America, but we have a long way to go in this area to catch up with what has been happening in developing countries. Robert Boardman Toronto, Canada

Electric Motorcycles

I was very pleased to see articles on electric motorcycles and PEVs (KickStarted: Electric Motorcycles Gain Traction and Personal Electric Vehicles Get More Personal in HP144), but a bit disappointed

Tired of fighting your distributor?

North Americas Exclusive Distributor of ET Solar.

(916) 679-4044 www.ussolardistributing.com 34

home power 145 october & november 2011

letters from readers column subtitle

column title mailbox

Courtesy Air Photo Service Co. Ltd., Japan

Can the experts cited in the articles offer any leads on affordable trikes that I can look forward to even if they arent here now? Heres toward a clean, lean winter commute that is also good, clean fun! Christina Snyder www.michiganpassivehouse.com Youre absolutely right, Christinathe threewheeled products are, at this point, either rare-collectible or prototypes (like the Corbin Sparrow, the Meyers Duo, or the Zap). Plus, they are fairly expensive. As far as trikes go, Im not sure theres anything available thats not in the prototype or concept stages. The Can Am Spyder gas version is in production, but I know of no plans to go electric. At any rate, none of the three-wheeled vehicles (electric or otherwise) will meet your pricing needs. Im not sure an open vehicle would be the ticket for you anyway, what with the cold winters. I think that looking at a hybrid or an all-electric car is your best bet, and although they are pricey, there are incentives in Michigan that might help you out, which can be found at www.hybridcenter.org. Ted Dillard

The Unraveling of Nuclear Energy

About three decades ago, the Swedes considered the risks of nuclear energy, added up the costs, and did the math. What they found was that the astronomical amounts that the Swedes were paying in subsidies to produce electricity from nuclear energy far exceeded what they were getting out of it. Swedes arent dumb, and voted in a national referendum to shut down and decommission all their nuclear energy reactors by 2010. The Swedish nuclear weapons program had already been terminated when Sweden signed the nuclear nonproliferation treaty in 1968. Sweden now operates three nuclear facilities, with a total of 10 reactors generating about 45% of the countrys total electricity. A narrow two-vote conservative resolution extended the reactors operation without new subsidies or construction. The opposing parties have declared their intention to continue with the shutdown. About a decade ago, Germany arrived at identical conclusions, and the country voted landmark legislation to replace all fossil and nuclear fuels with solar, wind, geothermal, and biomass renewable

Nuclear plants in Fukushima suffered explosions and nuclear fuel meltdowns as a result of the March 2011 earthquake.

energy by 2030. Germany is already producing about 20% of its electricity from renewables, accounting for almost as much as its nuclear energy fraction. Recent reports from Germany indicate that the percentages from renewables may be too conservative, and that the country may have moved ahead much faster than was predicted. The same feed-in-tariff (FIT) laws that were passed in Germany have already been approved by the 24 member nations of the European Union, and are being considered

Just when you thought it couldnt get any better...

S-5! has once again made cutting edge innovations to the industry standards for attaching solar panels using the S-5-PV Kit.
The new stainless steel mounting disk is designed to ensure conductivity with module frames. Now, the S-5-PV Kit provides module-to-module continuity within a string of modules. When the PV Kit is properly installed, ground lugs and copper wire will only be necessary to connect module strings and ground the system. In most cases, that cost savings is sufficient to pay for the entire S-5! clamp/PV Kit setup! The S-5-PV Kit continues to be the easiest, most cost-effective way to install solar panels directly to standing seam metal roofs, remaining the most popular choice worldwide. To find out more, call 888-825-3432 Or visit www.S-5-solar.com/hp Visit us in October at Solar Power International Booth

#5106

UL Listed to 2703, a brand new subject for bonding and mounting! ETL Listed to UL 1703.

www.homepower.com

35

mailbox column title

by some other 40 nations around the planet. Germanys Chancellor Merkel recently announced that her conservative government is moving to phase out nuclear energy by 2022 and accelerate the transition to a clean, low-carbon, non-nuclear energy future largely built on RE and energy efficiency. The U.S., French, and Japanese nuclear programs are not different. These programs exist only at the expense of hundreds of billions in taxpayer subsidies, government loan guarantees, and tax exemptions. And with the U.S. Price-Anderson Act, in case of a nuclear accident, the owner-operator of the nuclear plant is liable to pay damages of up to about $12 billion. Any amount above that becomes public liability. Want it or not, wethe taxpayersfoot the bill and pay the damages, whatever they might be. Corporations pocket the profits, while the cleanup costs and losses are socialized what a deal. One single accident could total upwards of $500 billion, and go up to $1 trillionno one can tell. National and international polls show the publics opposition and that they want the nuclear industries shut down. A recent landslide vote in Italy forced the Berlusconi

letters from readers column subtitle

administration to abandon plans to restart Italys nuclear program. Enter Fukushima: With six nuclear reactor cores packed in close to each other in a single nuclear facility, it is exceedingly clear that if even a single reactor suffers a minor accident, it becomes exponentially complexif not altogether impossibleto maneuver around the plant in any normal way. This puts the other reactors at risk of a series of largely predictable cascading eventsthat is, successive meltdowns. Three of the nuclear reactors were operating when a whopping 9.0 Richter scale earthquake hit just offshore; a series of powerful tidal waves followed shortly thereafter. We now know that the earthquake damaged the cooling systems of the Fukushima plant, and that fuel core meltdowns started before the ensuing tsunami hit Japan. Once cooling stops, temperatures rise very fast within the densely packed nuclear core fuel rods, and whatever cooling water is left rapidly boils and evaporates. The International Atomic Energy Agency (IAEA), a staunch proponent and supporter of nuclear energy, routinely downplayed the

amount of materials damage and loss of life at Chernobyl. A recent peer-reviewed publication originating from Russia puts the cancer death toll between 1986 and 2004 at a whopping 1 million human lives. The recent claim by the IAEA that no one will die in Japan is nothing but another criminal lie. The complete cleanup costs and number of victims, as in Chernobyl, are extremely hard to estimate, and will likely escalate in the $100 billions and, as in Russia, may result in the possible downfall of Japan. Cancer victims due to the fallout of radioactive isotopes will continue for hundreds, thousands, hundreds of thousands of years. The Fukushima disaster is far from over. It is beyond a shadow of any doubt that these are extremely dangerous, difficult, if not completely impossible situations to solve or deal with in physics, engineering, materials science, and chemistry. We do not have the technology to safely handle such high levels of concentrated radiation, temperature, and pressuresnot now, not anytime soon. The melting fuel requires massive cooling that will send vast quantities of radioactive water into the global ocean food chain, local water tables, surrounding soil areas, food crops,

Join our Growing Network of Successful Franchise Partners!

The Benefits are Clear
Established National Brand Proprietary CRM/Proposal Software Comprehensive Training Reduced Barriers to Market Entry Turnkey Solar Business Platform Manufacturer Direct Pricing

Lighthousesolars franchise program has exceeded our expectations. The franchising staff is extremely knowledgeable and professional. Their training program teaches you everything you need to confidently start your business and the amount of ongoing support weve received has allowed us to focus on building our business. Simply put, we see ourselves as partners with some of the best people in the industry. Bill Wallerstein - Lighthousesolar Westchester, NY

Lighthousesolar Franchising Company | Apply online today: www.lighthousesolarfranchising.com

36

home power 145 october & november 2011

letters from readers

mailbox
Xzeres 442SR
Annual Energy Output
Avg. Wind Speed (mph) 8 9 10 11 12 13 14 kWh / Year 5,465 8,190 11,413 15,050 18,992 23,112 27,277

and the global atmosphere for a long time, and a much longer time still to come, for present and future generations. These are nothing short of crimes against the planet and against humanity perpetrated by the dissemination of torrents of unchecked lies and falsehoods that began at the end of WWII. Electricity from nuclear power will be too cheap to meter, so the harp played. It is time to demand an answer from all those who have been perpetrators and accomplices in these crimes: Is this the best you can do, lie? and hold them accountable. (For more info, see www.nirs.org.) Tony Pereira Lamar University, Beaumont, Texas

Third up was a horizontal-axis wind turbine (HAWT), a Skystream. The installer tuned it over the Internet, and weve had no problems. Back to my German VAWTthe inverter is blown out, and the company is out of business and nowhere to be found. Now its just spinning artwork. If you like artwork, go with a VAWT. If you just want work, go with a HAWT. Dr. Richard Henry Mount Sterling, Kentucky

VAWT Blues

My new dental office will have wind power, solar electricity, and solar hot water. First up was a vertical-axis wind turbine (VAWT). It sure looked cool, and with help from my German-speaking patients, we had it imported and put it upmore on this later. Second up was solar electricity400 W of PV modules and Enphase inverters. Weve had no problems, and we plan to add more.

The grid-tied systems with battery backup schematic in PV Systems Simplified (HP144) included an inverter model that is not designed for bidirectional utility-interactive systems. Inverters manufactured by OutBack Power Systems and SMA America (Sunny Island) are more commonly used for this type of system. Is Wind Electricity Right for You? in HP 143 included information about the Xzeres 442SR that is out of date, with corrected manufacturers data in the table. For more info, see www.xzeres.com.

Errata

write to:
[email protected] or Mailbox, c/o Home Power PO Box 520, Ashland, OR 97520 Published letters are edited for content and length. Due to mail volume, we regret that unpublished letters may not receive a reply.

Were all in this together.

Solar, do the next right thing

Wholesale/Retail Distributors
Exceptional Service Low Price Guarantee

888-826-0939
www.thesolarbiz com
www.homepower.com

37

residential solutions 1.8 to 15kw

real world solution:
Size: 5 kW Installer:

Magnani Residence

Solectria Renewables, LLC is the leading U.S. based grid-tied photovoltaic inverter manufacturer for residential, commercial and utility-scale solar installations. Our versatile line of high efficiency products provide power solutions ranging from 1 kW residential systems to multi-megawatt solar farms. Solectria Renewables products are backed by more than 30 years of experience in the power electronic and inverter industries and supported by world class warranties. All of our commercial and utilityscale PV inverters are manufactured in the USA, ARRA compliant, Ontario FIT Content Compliant, and listed to UL 1741/IEEE 1547.

Location: Framingham, MA Products: PVI 5000

We have partnered with and chosen Solectria Renewables residential inverters for various installations since 2005. Their residential inverters are the most efficient and reliable in the grid-tied PV market. Matt arner, President and Certified NABCEP PV Installer, SolarFlair Energy, Inc.

www.solren.com | [email protected] | 978.683.9700

ask the experts

Cooling with Radiant Floor?
My wife and I are planning a new house, and weve decided we want radiant floor heat, since its the most efficient. We have our own well, and it seems to me that if we have water circulating through the floor it could also be used in the summer to cool the house, but Ive never heard of anyone doing that. Will it work? If not, whats the best way to cool the house? Dawn Crawford Rapid City, South Dakota Im not sure that radiant floors are the most efficient type of heating, though they are extremely comfortable in the winter. Most people who have lived with radiant heat in any of its formshot water radiators or baseboard units, radiant wall or ceiling panels, passive solar, and even wood heaterstend to get a contented look when talking about the comfort of their homes in winter. In theory, since a warm floor heats up your feet, you will be comfortably warm at lower air temperatures, so the heating system provides comfort using less fuel than a conventional system. In addition, warm surfaceswalls, windows, ceilings, or floorstend to suck less heat from your body and will provide comfort, even if the air in the room is cooler. That theory makes sense to me, but I havent seen any evidence that homes with radiant floors actually use less energy. If, for instance, you spend much of your time with your feet propped up in the La-ZBoy, Im not sure the warm floor will have a big impact on your bill. Part of the problem is the financial one youve identified. Is there a way to heat with radiant floors and not also have to spend the money for a forced-air cooling system? The idea of circulating cool water through the floor seems to come up a lot, particularly from folks who have their own wells and figure they can circulate 55F water through the slab to pull heat out of the house. The idea sounds good, but is not workable. We know what happens to a cool iced tea glass when set out in a hot, humid room. Water condenses out of the air onto the glass. Similarly, if your strategy worked, your floor would be cool enough to make moisture in the air condense, turning your entire house into a gigantic SlipN Slide. An air conditioner blows hot, humid air over a cold coil, the water condenses on the coil, drains into a pan, and then into the drain or the yard. Turning your entire floor into a huge condensate pan might be fun for the kids, but not so cool for the rest of us. There are other strategies that can work. First, build your house tight and very well-insulated. Install a mechanical ventilation system for fresh air and moisture control. Use as many of the traditional methods of keeping heat out of the house as you canminimize west- and east-facing windows, use properly sized overhangs, use shade trees, or shade the house with porches, particularly on the west and east sides. Once youve reduced the cooling load, you can air-condition the house in several ways without ducted systems. High-efficiency window air conditioners mounted through the wall can be effective, low-cost, and reasonably energy efficient. The biggest problems are proper placement and noise. A mini-split air conditioner or heat pump might work for your situation. It uses an outdoor unit very similar to conventional air conditioners, but instead of a big air handler and duct system, panels are mounted inside various rooms. They look like window-type airconditioning units from the front, are only several inches thick, and can be mounted anywhere, including on interior walls.

renewable energy Q&A

These systems are not cheap, but could be less expensive than installing a whole-house ducted system. Units that provide heating and cooling are available, and when these functions are combined, they are very economical. Mini-splits are quieter than room air conditioners, and being able to install their outlets on interior walls is a big plus. Arnie Katz Printed with permission from www.advancedenergy.org

The outdoor unit of a mini-split air conditioner and heat pump.

40

home power 145 october & november 2011

See us at SPI in Dallas! Booth #3237

SnapNrack rter ports a qua sup dules million mo ng! and counti

Homeowners love our sleek lines.

Youll appreciate the bottom line.

solar electric system. And youll spend less time on the roof, thanks to SnapNracks many design-integrated time and money savers innovations like one-wrench- tsall fasteners, a no-ties wire management system, universal module clamps, and snap-in channel nuts. Contact us today to nd out how we can help you sell more systems with less hassle.

our customers will be delighted by

the clean, nished edges of their

SLEEK. STRONG. FAST.

SnapNrack systems work with all leading PV module brands in pitched roof, metal roof and ground installations.

(805) 540-6999

www.snapnrack.com [email protected]

ask the experts

Understanding PV Output
In full sun, my eight Solarex modules, rated at 120 watts each, are putting out only 536 watts (10 amps x 53.6 volts) in my off-grid battery-based systemwhats up? Kevin Green Anacortes, Washington Your electrical math logic is right onvoltage times amperage equals wattage. In a perfect world, your 960 W-rated array should provide 960 W in full sun. There are several reasons why you arent seeing the full rated output of your PV array. In fact, its relatively rare to see the full rated output. Lets look at the reasons. First of all, your battery bank is probably approaching full and in absorb at that voltage. In this situation, your charge controller is partially turning off the solar-electric array to prevent overcharging the batteries. Modern controllers use pulse-width modulation (PWM) to do this, turning the array output on and off very quickly, and changing the duration of the off and on times to maintain the desired charge rate. If your batteries were at a lower state of charge (SOC) so that your controller was charging at its max, you still would rarely see the rated output of the array. The primary reason for this is the unrealistic rating system we use for modules. All modules are tested in what we call standard test conditions (STC)1,000 watts of light per square meter at 25C. Both of these conditions are unusual for real-world PV arrays. A bright sunny day, with no haze, smog, or anything else to filter or obscure the sun, will produce 1,000 watts per square meter. But to get this much irradiance, the array also has to be perpendicular to the sun. And 25C is 77F. Ask yourself how often a black or dark blue surface in the sunshine will be that coolnot often. Its perhaps counter-intuitive, but when PV modules are hotter, their performance (specifically, their voltage) drops. So in most cases except in winterarrays dont witness 25C conditions. When they do, the sun conditions are often not ideal (because of latitude, angle, weather, etc.). While your charge controller does maximum power point tracking (MPPT), other readers may have non-MPPT controllers, which brings in another reason for less-than-rated performance. Without MPPT, a system is limited by the battery bank voltage. The array voltage will be clamped to just above the battery voltage, so the charging potential above battery voltage will not be available, resulting in lost array power. An MPPT charge controller can turn excess array voltage into usable amperage that the battery bank can absorb. During cool weather and when the batteries are at a low SOC, you will see the array wattage increase. From the photo, I see that your array is tilted to a winter angle. This makes sense because you are off-grid, and winter is the time your system sees its biggest energy challenge. Your arrays rack is adjustable, and you could tilt it flatter in summer and get more production, but many people dont find it worth the trouble, since you generally have more energy than you need during that season. Output losses can also occur due to module soiling. Wash your modules at least once a year with mild soap and water. If youre in a dusty or high-grunge environment, you may need to clean them more often. Then there are potential losses due to PV module production tolerancei.e., depending on the manufacturer production tolerance (%), the actual module output, even under STC, may be less than

renewable energy Q&A

the wattage rating. For example, if your modules have a +/-10% production tolerance, the actual STC wattage can range from 108 to 132 watts. Also, as modules age, they degradean estimate of 1% power loss per year is often quoted. Additionally, voltage drop due to wiring runs is a factor (the loss depends on the wire gauge used) and controller inefficiency can also contribute to system losses. In the end, assuming a completely unshaded array (and on a sunny day with a battery not yet full), Im pretty happy if my array produces 70% to 85% of its rated output. So have no fear, your PV array is likely on track, and all is well. If you want to start a campaign to get PV manufacturers to use a more realistic rating system, I will be on your advisory board! Ian Woofenden Home Power senior editor

PV or SHW?

I was looking forward to having a solar hot water (SHW) system installed at my house until I attended an informational seminar on solar water heating. The salesperson basically told us, invest in PV if youre a small household that practices water conservation and efficiency. His rationale was this: Where my husband and I live in the Pacific Northwest, winters are fairly cloudy and SHW production will be low in those months, stretching out the payback time for the system. With a water-conserving household (low-flow fixtures, water-saving appliances, etc.), he said wed be wasting money on a system that would only be working optimally for us half

42

home power 145 october & november 2011

Courtesy Chuck Marken

ask the experts

renewable energy Q&A

than half the solar resource compared with the summer. This wide seasonal diversity of the resource is not the case in much of the United States, and space-heating options can be viable alternatives in those places. But domestic solar hot water systems are a different story. Theyre used the entire year and, as long as the system is sized to not overproduce significantly in the summer, the economic evaluation in HP127 is still valid for even your region, albeit dated. The best way to address summer overproduction in any system is to configure it as a drainback system. If that isnt possible, there are many methods of controlling antifreeze system summer overproduction described in Overcoming Overheating in HP142. Chuck Marken Home Power solar thermal editor

See PV vs. Solar Water Heating: Simple Solar Payback in HP127, comparing the economics of small SHW and small PV systems. At the time, with prevailing costs, the SHW system appeared to have about a 2.5 to 3:1 advantage in return on investment (ROI) with no incentives and both technologies displacing electricity. This has probably been reduced to perhaps about a 2:1 advantage today due to PV prices continuing to fall. The information you received regarding the seasonal diversity of the solar resource in the Pacific Northwest is accurate. At a tilt equal to latitude, the winter six months come in at an average of a little more than 2 sunhours per day, with the six summer months having just more than 5 average sun-hours. Maybe the PV salesperson was thinking of or passing on information regarding solar thermal space-heating systems; if thats the case, the advice is sound. The utility grid has almost unlimited storage capability for PV systems, while storage tanks have a much smaller storage capacity for SHW systems. In areas with wide differences in the seasonal solar resource, PV has a better ROI than home-heating systems using solar hot water collectors. The SHW home heating equipment will only be used half the year (or less) and at the time when there is less

of the year, and that wed have to figure out what to do with excess hot water produced in the summer months. What do you think? Are we barking up the wrong RE tree, and should we just invest our dollars in expanding the planned PV system to cover our water-heating needs rather than paying for a SHW system? Sandy Wellington via e-mail

write to:
[email protected] Published letters are edited for content and length. Due to mail volume, we regret that unpublished letters may not receive a reply.

Let groSolar

Fatten Up Your Bottom line

Buy Direct from the Manufacturer

groSolar Introduces

Project Procurement Services

Call groSolar Now to Learn How 800.374.4494 ext. 2990

North Americas Premier Solar Distributor Wholesale Solar Products for Professional Installers groSolar.com/HomePower
44
HomePower_OctNov.indd 1

800.374.4494 ext. 2990

8/4/11 9:39 AM

home power 145 october & november 2011

The biggest thing in solar.

(actual size)
Welcome to the next generation of microinverter.
Not just smaller: more powerful, more efficient, and easier to install.

Learn more: enphase.com/next-gen Solar Power International, Booth #2009

Dont want YOUR

PV Investment
to wash away?

Insist on NABCEP Certified

PV Technical Sales Professionals and Installers.
Quality assurance throughout the sales and installation process.

Our PV system was a big investment in the future and I wanted it installed by a professional with national credentials to make sure it was installed properly. The NABCEP Certified installer did just that, and the system is operating flawlessly providing our family now with free renewable power.
Mike Burnetter, Home Owner and Professional Engineer

Find a NABCEP certified professional near you at

www.nabcep.org

SPI in Dallas!
Booth #720

See us at

New from Quick Mount PV...

The Worlds Strongest Solar Mounts

The strength of the QBase enables lowslope roof stando s up to 12 inches with Industrybest shear strength for a non-welded mechanical mount. The New Roof Mount uses a 3.75-inch stando for a low-pro le roof array.
12" 376 lbs.

Quick Mount PV announces new 100% code-compliant, waterproof mounts for low-slope commercial roofs and for new home construction and pitched roof replacement.
The Low Slope Mount is the strongest mount you can buy for mechanically attaching commercial PV systems to TPO, PVC, EPDM, built-up asphalt, and virtually all other nonmetal low-slope roofs.
Low Slope Commercial Mount

9" 579 lbs.

7" 775 lbs.

3.75" 1446 lbs.

The New Roof Composition Mount integrates PV installation smoothly into the work ow between the trades during new home construction or roof replacement.
New Roof Composition Mount

QBase
WHERE THE ROOF MEETS THE LOAD

Also from Quick Mount PV: Classic Comp & Shake Mounts, and our brand new Universal Tile Mount!

The Low Slope and New Roof Comp Mounts are built around the all-aluminum QBase. With four buttresses to support the load, QBase makes these o -the-shelf solar mounts the worlds strongest by far.

Call or visit us online to learn more:

925-687-6686 www.quickmountpv.com [email protected]

or DIYAdvicePRO? Practical for Homeowners

by Justine Sanchez, Joe Schwartz & Ian Woofenden

JEFF: Accomplished Do-It-Yourselfer

SEAIRA: Seasoned Professional

48

home power 145 october & november 2011

DIY reality check

The installation of most residential PV systems is usually better left to the pros, but if you have the right set of skills and expectations, installing your own system can be a realistic goal.

s it common for homeowners to design and install their own solar-electric systems? Should I install my system or hire a licensed professional to do the work? What skills and tools do I need to tackle a home-scale PV project? How much will I save if I install the system myself? We frequently get questions like these from Home Power readers. Rather than defaulting to the obvious answer, it depends, we explore a long list of variables you should thoughtfully consider before tackling the design and installation of your PV system. Owner installation is definitely not for everyone. Like any home improvement project, its important to realistically assess your skills, and weigh the benefits and potential pitfalls. Installing a PV system certainly isnt rocket science, but doing it well and safely requires experience working with electrical systems, some serious research, and plenty of sound advice.

paired to its own small inverter. Microinverter-based arrays operate at 240 VAC rather than at high-voltage DC, making electrical wiring a little safer to work with. Whether you are using microinverters or central inverters, youll still need electrical skills, tools, and savvy, but batteryless gridtied systems are actually quite straightforward, consisting primarily of racks, modules, disconnects, inverter(s), and wiring. A grid-tied battery-based system is another matter. Introducing batteries involves more complication in planning, implementation, and operation. To start, youll need to know how much battery storage you want or require, which means youll need to know your backup load profile and how long a utility outage you want to protect against. Though you can buy some or even most parts of a battery-based power center pre-wired, you will still need to configure and wire your battery bank, tie it and your PV array into your power center, and then connect the system to your backed-up subpanel and the grid. Most will need someone assisting in person or on the phone as you plan and install the system. Operation of a battery-based system is more complex than a batteryless system, and the batteries will require varying levels of maintenance, as well as periodic replacement.

System Scale and Type

First, its important to consider the size of the PV system you want to design and install. Theres a huge difference in the cost and complexity of a 12-volt PV system with a few modules, designed to power some tunes and a couple of lights, compared to a multikilowatt, roof-mounted, gridconnected system operating at up to 600 VDC. The former small system can be a great DIY undertaking for most handy individuals. Unless you are working alongside a willing professional, however, the latter should not be tackled unless you have significant experience working with highvoltage wiring, a firm understanding of the National Electrical Code (NEC), and access to the required safety equipment. System type is also a consideration. Battery-based and batteryless grid-tied solar-electric systems are quite different, and require different levels of preparation and involvement. You need to understand the system type you want to install, and then assess your abilities and interest to determine if you can handle the job. Grid-tied systems can be batteryless or battery-based. Batteryless systems are the most common, and are also the simplest, most cost-effective, and most environmentally friendly. You can find examples of this system type in Home Power, in supplier catalogs, and around your community. Batteryless PV systems can be bought as packages from suppliers and, with the proper support, can be almost colorby-number. These systems can employ one or more central string inverters or microinverters, where each module is

echie Gear T
Batteryless grid-tied PV systems may be the simplest conceptually, but they still require good design, mechanical and electrical skills, adherence to codes, and safety. Are you adequately prepared?

Shawn Schreiner

www.homepower.com

49

Ben Root

DIY reality check

Critical Planning
The Solar Pathfinder (left) and the Solmetric SunEye (right) are professional-quality solar site assessment tools that provide valuable information for your systems design.
Shawn Schreiner

Going off-grid requires a commitment to providing all electricity to all of your loads, all of the time. The design phase is crucialyoull need to understand your load profile, your resource, and the equipment capabilities. While many off-grid systems have been built by DIYers over the history of the RE industry, designing and installing a code-compliant system for a modern off-grid home is not a job to take lightly. All of the system users in the household will need to be involved from the beginning if you want a system that doesnt disappoint.

Designing Your System

There are many steps involved in designing a PV systemdo your homework to make sure you cover all of your bases. Site-specific variables will dictate your systems type, size, and location, and several other variables will dictate the components youll need. Evaluate your situation and goals to specify the system type. First, observe your site closely to make sure theres a good solar window at your proposed array location (ideally from 8 a.m. to 4 p.m., but 9 a.m. to 3 p.m. is acceptable). Sometimes, that open solar window is not on your roof, but in the yard, making a ground-mounted system optimal. Or perhaps you want a 4 kW system, but your shade-free space can only accommodate 2 kW. Then there are the myriad individual equipment requirements with which you will need to be familiar. For example, if you found a good deal on a specific inverter, your sites high and low temperatures and the module specifications will play a role in how many modules you can string in series to connect to that particular inverter. To comply with and pass your electrical inspection, you will need to be aware of all the various NEC requirements that pertain to your installation. Local requirements may also come into play. For example, while many inverters offer integrated DC and AC disconnects, your local authority having jurisdiction (AHJ) may require additional disconnects. In addition to the NEC, local fire codes can affect your

installation. For instance, some mandate 3-foot setbacks on roof-mounted arrays to provide pathways for firefighter access and smoke ventilation. Performance factors also need to be considered. Do you have enough know-how to optimize the systems design? For example, even minimal shading of a PV array during the prime solar hours can significantly reduce your systems output. Also, PV module output declines with increasing temperatures, necessitating a design with good airflow around the modules. The list of considerations goes on and on. Thats why folks seek professional assistanceto ensure that their investment in a PV system isnt undermined by trying to save a few bucks on installation costs.

Buying Equipment
When it comes to buying equipment for your PV system, dont buy cheap! We mean this on two levels. First of all, buy quality equipment. Most of us are accustomed to having reliable grid electricity. If you want to have a reliable solarelectric system, youll need high-quality gear. Find out what suppliers are selling the most of and what installers are buying. Be wary about a new product being sold only from

Buying your equipment from a source that can offer technical support in the design, installation, and troubleshooting phases is worth the extra money.

50

home power 145 october & november 2011

iStockphoto.com/alexsl

DIY reality check

one source. Wait until the pros in the industry start trying it, using it, and praising it before you spend your money. Dont automatically go for the dealer with the lowest cost. Too often, DIYers end up with a low level of support along with a low price. Especially if youre installing your first systemyou will need some hand-holding. Buy your gear from someone who can help you during and after the installation, and expect to pay more to include that level of support and service. Second, if possible, try to buy locally. Being able to develop a relationship with your supplier is priceless. Theres nothing like being face to face when it comes to a clear understanding of design, and when it comes to resolving issues with an order, product, or system. Consider collaborating with a local, professional RE installer, if there is willingness. Buy your components through a local company, giving them their profit margin. Perhaps even hire one of the technical people at the company to review your design before purchase, and again before inspection. This can be a great partnership that will serve your system well. If you do run into problems during design, installation, or operation, youll have someone to turn to who has walked the path before. Dont buy discounted equipment and then go looking for an installer. These folks make their living selling and installing PV systems. They know the ins and outs of the equipment they prefer to install, and they know how to install it. They also need to mark up the equipment to make their living, just like all businesses. Trying to get something for nothing will most often result in hard feelings and poor relationships and not the help youre looking for. If you do find a pro willing to install equipment you already bought, expect to pay top per-hour electrician wagesmost likely eliminating the savings realized on the inexpensive equipment. Most manufacturers are global companies that have little interest or dedicated resources to handle technical questions from homeowners, and this may include warranty claims and issues. So dont expect to call the manufacturer of your inverter for help with string sizing, or get the footing requirements for your ground-mounted array from the mount manufacturer, for example.

DIY PV modules
Thinking about building your own PV modules from scratch? Think again. While this has been done on occasion (especially in developing-world situations), we strongly recommend against it. First of all, you wont be making the PV cells. This is high-tech, clean-room technology, not something youre going to do in your garage. And this is the most expensive and important part of the PV module manufacturing process. You could buy cells and assemble your own modules. We see opportunists advertising plans to do this cheaply, but we suspect that the main benefit is to the plan producers bank accounts. While a handful of companies are promoting DIY module building as a practical alternative, the realities of the actual cost and, more importantly, product safety, are being ignored. Without question, PV system components should be listed to applicable Underwriters Laboratories standards, just like any other electrical product in your home. These standards were developed to ensure the safety of you, your family, and your neighbors. Unlisted components are an accident waiting to happen. PV modules are incredibly long-lasting devices if they are wellconstructed. Most carry 20- to 25-year warranties on energy production and will continue producing electricity for 40 years or more depending on the quality of their construction. Trying to do this yourself will rarely, if ever, result in the durability and longevity you will find in well-manufactured modules. Building PV modules is best left to PV manufacturers.

Tooling Up
You will need a wide range of construction and electrical tools to install your PV system (see Tools of the SolarElectric Trade in HP105). The basic construction tool list for a batteryless, roof-mounted, grid-tied system includes: drills (cordless and AC) with various attachments, including drill bits, hex bits, Phillips bits, and hole saws; a reciprocating saw; socket wrenches; a hammer; a level; and an assortment of screwdrivers and open-end wrenches (the ratcheting kind are great). Required electricians tools include wire strippers, cutters, and crimpers; needle nose and linemans pliers; a hole-punch kit; a conduit bender; and a fish tape. The list grows if you are installing a battery-based system, as you will likely be dealing with constructing a battery box, and needing to cut and connect large battery cables and lugs. If the system is ground- or pole-mounted, you will need equipment for digging trenches and post holes (i.e., shovels and a post-hole digger, or access to a power auger and trencher). Additional tools include a torque wrench to properly tighten wire terminations, and a digital multimeter for verifying voltage and polarity during installation and for ongoing system maintenance. A DC clamp-on amp-meter is also a handy tool for checking the output of individual array strings or circuits. Specific safety equipment is also required (see the Safety, Safety, Safety section). Youll also need access to solar-specific tools for both site analysis and installation. While there are some wide-open solar sites where array shading is not a concern, the majority of sites, especially in residential areas, will have trees and buildingsso shade analysis will be necessary. Shading

www.homepower.com

51

Courtesy Helios Solar Works

DIY reality check

Specialty Tools
While many of the necessary tools are common to the well-equipped homeowner, some specialty PV installation tools are either necessary or a great convenience. The cost of tooling up can negate the savings of doing the work yourself.
Shawn Schreiner

specifics impact component selection and array layout, and can influence the availability of some financial incentives. Excessive shading will have potentially crippling impacts on system output and your return on investment over the PV systems life. Tools such as the Solar Pathfinder ($269) and the Solmetric SunEye ($1,995) are used by the pros to determine shade factor, and/or compare the solar access of different array locations. The price of these shade analysis tools will likely put them out of reach of a homeowner working on a one-time installation. For iPhone users, Solmetric offers the Solmetric iPV app ($29.99). While it is not as accurate or quick as the SunEye, it offers users a simple shade analysis at an inexpensive price. Shade analysis tools have also recently been developed for Android-based smart phones and tablets. If youre not already tooled up for significant home improvement projects, including electrical work, the cost of acquiring all of the necessary equipment could easily offset any savings you may be expecting from installing your own system. If you do have a good selection of tools in the shop, additional purchases may be minor, but should still be considered prior to embarking on a self-installed PV project.

Installation Experience
The skills youll need to install your PV system will depend on the systems complexity. Overall, you will be doing conceptual, mathematical, mechanical, and electrical work. In some respects, the conceptual work may be the hardest. Youll need to understand your energy needs, your solar resource, the equipment available, and how the gear fits

together into a full system. If you blow it here, no amount of mechanical and electrical savvy will rescue you from poor function. Plan to spend much more time studying, planning, and designing than you spend implementing. Professional installers get used to doing the same tasks over and over. You wont already have the benefits of learning from the inevitable mistakes. Those who are used to undertaking major homeimprovement projects will likely be the most prepared to pursue a DIY PV system. When it comes to the mechanical work, youll need to know how to use tools and fasteners properly to make roof- or pole-mount attachments; install roof flashing; secure heavy electrical components to the wall; etc. Battery banks and enclosures require another level of mechanical work, involving security, hazard protection, and dealing with heavy weight. The electrical work is more hazardous and more detailorientedand can be more crucial than the mechanical work. Note that licensed electricians study for years to gain the skills to bend conduit, pull wire, and make secure connectionsall while meeting the strict requirements of the NEC. Consider your skills and experience carefully before jumping in. Having a mentor on the job or nearby may be your wisest decision. Once again, you are only doing this job onceelectricians have the benefit of long experience and training. They have tricks and techniques that make the job go quickly and smoothly. Consider taking a basic wiring class at your local community or technical college, so youll have some practice time on someone elses wire, and another source of mentorship.

52

home power 145 october & november 2011

DIY reality check

Permitting Considerations
The appropriate building permits will have to be obtained and the system will need to pass an inspection. This can be a painful process if you are not used to performing electrical work. Inspectors will be on the lookout for all possible NEC violations, including sloppy work, improperly sized conductors, lack of conductor protection, and improper equipment grounding and labeling (see Residential PV Systems: Common Code Violations in HP141). If your system doesnt pass muster, you will usually be charged a reinspection fee each time the inspector comes out. Professional installers who have been in business for awhile have been through many inspections and have a good handle on what the local AHJ expects. They have the experience and the knowledge to work with inspectors if anything comes up that the inspector may not be familiar with. Homeowners will typically be greeted with a greater level of scrutiny from building inspectors. Additionally, there is a new section in the 2011 NEC, section 690.4(E) stating that PV equipment and systems, and all associated wiring and interconnections, shall be installed only by qualified persons. See Code Corner in this issue for a discussion about what constitutes a qualified person in the eyes of the NEC and your local AHJ.

Education
If you are determined to install your own system, consider getting some training. Coursework and hands-on exercises can walk you through the steps of designing and installing a PV system and allow mistakes to be made in a classroom/lab setting rather than during your home system installation. Several organizations offer on-site and online courses to help you get the basic knowledge you need (see Charting Your Solar Course in HP136).

DIY Savings?
Installation labor costs typically account for 10% to 20% of a systems total cost. Labor costs for a simple 3 kW roof-mounted, batteryless grid-tied PV system might be between $2,000 and $3,500. The exact amount you could save by installing the system yourself will depend on your particular system type, and its size and mounting method. For example, batterybased PV systems are much more complex and require more time to install the extra components (such as the battery box, batteries, battery cabling, charge controllers, battery metering, extra disconnects, and overcurrent protection). Array size will dictate how many module mounts and inverters are required. This, in turn, will determine the time required to install the complete system. The array mounting method will be a major factor. For example, a ground-mounted system (see PV Ground-Mounting in HP144) requires much more prep worksuch as digging footers and conduit trenches, setting posts, and pouring concretecompared to a roof mount.

Kris Sutton

While you can obtain a lot of system design knowledge from online and classroom presentations, when it comes to installation specifics, nothing beats hands-on training. These courses are not short nor inexpensive, and are usually geared toward individuals wanting to become professional installers. Often, folks who want to install their own system are the same people who are pondering a career shift into the PV industry. Training followed by a home installation can be a great progression if youre considering entering the PV industry. The value of living with a PV system, for both homeowners and up-and-coming professionals, is priceless.

Typical PV System* Costs

Inverter 14% PV Rack 10% Taxes & Fees 7% Balance of System 4%

PV Modules 50%

Labor 15%

*For batteryless grid-tied systems

A DIY system may impact your incentive eligibility. While you can still take the 30% federal tax credit, in some cases, you may not qualify for state, local, or utility rebates if you install the system yourself. A self-installer could lose out on thousands of dollars in state and/or utility incentives. To find out what your system will qualify for, research the requirements for the various PV incentive programs in your area (see the Database of State Incentives for Renewables and Efficiency at www.dsireusa.org). For example, Xcel Energys Colorado customers who install their own systems are eligible for the Xcel Energy Solar Rewards program, which currently offers a $1.75 per watt payment (and $0.04 per kWh production incentive) for systems under 10 kW. However, these systems are not eligible for the state

www.homepower.com

53

DIY reality check

The Pro Perspective

Pros bring skills and experience to a project that a onetime installer does not have. The majority of installers have yearssometimes decadesof experience designing and installing systems. They know what works and what doesnt, and understand the subtleties of system design and changes in the National Electrical Code. They have relationships with building inspectors and equipment distributors, and have established peer networks for situations where even they may need advice. Professionals also can provide you with guidance and a streamlined process for navigating the typically complicated processes of applying for, receiving, and maximizing any available financial incentives. They may also offer system financing and leasing options that can minimize or even eliminate your up-front investment. Solar contractors are specialized, but they are no different than any other building or trade professional. They offer products and services that enable the smooth implementation of high-quality systems. That said, keep in mind that the level of experience, support, and professionalism can vary greatly between contractors. If your system will be professionally installed, find someone whose experience you trust, and verify it by checking both customer and business references. Spending some time on the Internet researching customer feedback on potential contractors can be helpful.

buildup, and taking precautions to avoid short-circuiting the batteries during installation or future maintenance. Once the PV installation begins, a whole new set of safety requirements must be considered. (See www.osha.gov/dep/ greenjobs/solar.html for an overview of installation hazards and precautions.) Most modern PV systems operate at dangerously high DC voltages and electrical shock hazards are present during installation. There are many precautions that must be taken to ensure you do not come into contact with these high voltages, like understanding and following safe installation order procedures. For instance, disconnect and inverter wiring should always be attached before the PV array circuits or grid are connected. Have a well thought-out plan for wire management and be on the lookout for array wiring that inadvertently gets pinched between the modules and the mounting structure. This

rebate program (currently set at $1.50/watt) unless they are installed by a contractor listed in the rebate program database. In Oregon, to obtain Oregons Energy Trust rebate, PV systems must be installed by a qualified Energy Trust solar trade ally contractor. Self-installed systems do not qualify. Any money you may be expecting to save by installing your system will be offset if you cant capture all of the available incentives.

Safety, Safety, Safety

When you approach any new activity thats potentially dangerous, it goes without saying that you should proceed slowly, methodically, and with extreme caution. When it comes to PV safety, you need to consider both design safety and installation safety. During the design, many critical safety aspects must be considered. For example, array fastening systems and hardware must ensure a secure rack-to-roof attachment. Nothing will bring your efforts to a crashing halt like modules being torn off the roof during a heavy wind storm. System wiring and overcurrent protection devices must be appropriately specified to prevent fire hazards. Conduit size, the number of conductors running in a conduit, and the installation method should always meet NEC requirements. Appropriate ground-fault protection is a requirement for PV systems mounted on dwellings and for some poleand ground-mounted systems as well. Batteries introduce additional safety considerations, since huge amounts of stored energy are present. They also require dealing with sulphuric acid, ventilating flammable hydrogen gas to avoid

Dangerous Situations

Topher Donahue

54

home power 145 october & november 2011

Shawn Schreiner

Electrocution from high-voltage DC electricity and falls from roofs are two of the hazards of PV system installation. For DIYers and professionals alike, safety must come first.

DIY reality check

can damage the insulation and potentially lead to ground-faults and arcing once the system is connected. Never underestimate the importance of suitable personal protective equipmentcutting corners here could have lifelong impacts for you and your family. Basic safety equipment like eye protection, ear protection, and respiratory protection should be used when needed. High-voltage electricians gloves and glove protectors should always be worn when working on live high-voltage DC circuits. Installing a roofmounted system poses potentially lethal fall hazards. While many homeowners may be comfortable working on the roof unprotected, that doesnt mean that its sensible. Fallprotection equipment, including harnesses, safety lines, and proper anchoring systems, should be used. Even if youre installing your system at ground level, ground-mounted systems often necessitate working with power augers and trenchers, which both pose operation hazards.

Advice for Successful DIY

Do your homework. Study Home Power articles, books, websites, manufacturer literature, etc. Take courses and workshops. Find others who have installed their own PV systems and study their designs, successes, and failures. Build a quality team. Find the expertise you need to support your DIY effort. Your equipment supplier will be a key part of this team. You also may lean on industry consultants, teachers, colleagues, friends, neighbors, and solar groups. Take your time. Tackling a one-time project is risky, and its more dangerous if youre in a hurry. The many DIY projects weve done have taught us that mistakes on slower and longer projects allow time for learning. Mistakes on quickly planned and implemented projects tend to multiply, because you dont have time to reflect on them, correct them while they are small, and learn from them. Document. Keep track of your design, the component specs and warranties, and installation progress and details. This will set you up for any troubleshooting needed, and will also give you information and expertise to share with others who may be interested in copying your success.

To DIY or Not to DIY

Over the last 20 years, PV installations have shifted from primarily owner-installed systems to professionally installed ones (see From the Crew in this issue). Should you install your own solar-electric system? To recap, the answer depends on the scale and type of system that will meet your needs; your understanding of system sizing and component selection; your skill level; and the range of construction and safety tools and equipment you have. A primary driver in the decision is also the potential impact that self-installation may have on any available financial incentives. If you decide to design and install your own system, be sure that you properly assess your abilities and have realistic expectations of the benefits and potential pitfalls of doing so. PV systems typically require a significant financial investment and youll want your system to function not only reliably, but also optimally over its more than 20-year service life. In many cases, the amount of savings youll reap by installing your own system will be minor. If you consider the value of time youll spend on the project, including up-front research and system design, as well as time spent wrenching, you may very well end up spending more time than you can afford. So why would someone install their own system? Whats the bottom line? The answer is probably similar to reasons for tackling any major home improvement projectfor the fun of doing it and the sense of accomplishment. And those are two powerful reasons in and of themselves.

Access
Justine Sanchez ([email protected]) is technical editor at Home Power, a Solar Energy International instructor, a NABCEP-certified PV installer, and is certified by ISPQ as a PV Affiliated Master Trainer. Joe Schwartz ([email protected]) is the editor of Home Power and SolarPro magazines. He began his career in RE as a PV, wind, and microhydro system installer in 1997. Ian Woofenden ([email protected]) bought his first solar-electric module in 1984. Early projects were DIY, with more recent ones implemented by professionalsall effectively turning solar energy into electricity. The more you understand about your PV systems design and operation, the better, whether you choose to go it alone, enlist the help of a pro at some level, or sit back and let the masters take care of things.
Shawn Schreiner

www.homepower.com

55

Power when You Need It!

w w w . s u n x t e n d e r . c o m

Just Released! Higher Capacity Group 31 Batteries

PVX-1180T | 12 Volt 118 Ah @ 24 hour rate

PVX-1290T | 12 Volt 129 Ah @ 24 hour rate

PVX-2560T | 6 Volt 256 Ah @ 24 hour rate

PVX-7680T | 2 Volt 768 Ah @ 24 hour rate

Sun Xtender Shines Long Service & Float Life

Sun Xtender Batteries are manufactured with the same design used in Concorde Battery Corporations premium quality aircraft batteries installed by aircraft manufacturers and adopted by military air forces worldwide. For both grid tied and off grid systems, Sun Xtender batteries are non-spillable and maintenance free. Constructed with valve regulated lead acid (VRLA) absorbed glass mat (AGM) technology, water replenishment and electrolyte checks are never required. Copper alloy terminals provide improved low resistance electrical connections and are more environmentally friendly than industry standard lead terminals.

NEW! AGM DEEP CYCLE POWER

PVX-1180T (12V), PVX-1290T (12V), PVX-2560T (6V) and PVX-7680T (2V) are higher capacity options in the Group 31 size, developed for more flexibility when designing configurations and planning battery bank layout. Thicker plates than the industry standard for excellent cycling capability, better float life and extended battery life. Proprietary PolyGuard microporous polyethylene separator around the positive plate and AGM to protect against shorts. Robust over the partition intercell connections are fusion welded for increased strength and lower resistance, in contrast to commonly used spot welds that are often a weak point and source of resistance. Durable battery cases and covers are made of a thick walled polypropylene for excellent impact resistance at extreme low temperatures and bulge resistance at high temperatures. Sun Xtender batteries are crafted for quality in the U.S.A. and ship Hazmat exempt.

A division of ConCorde BAttery CorporAtion

2009 San Bernardino Rd, West Covina, CA 91790 USA | 626-813-1234 | ISO 9001 + AS9100

Nature provides us with the gift of energy through the sun, but unfortunately, natures wrath may not be all that friendly to your PV system under stressful conditions. Snow, wind, extreme heat or cold, and seismic activities can wreak havoc on underengineered, underdesigned and insufficiently tested racking structures. Only UNIRAC solar structures have been engineered and third-party tested to withstand the harshest of elements and events for a long and enduring service life. Complies with IBC, IRC, ASCE-7-05, ADM, AISI, AISC, NEC and UL. For the highest level of engineering and construction with the lowest cost of ownership in the business, Unirac is the 24/365 solution for performance in and out of the sun. A HILTI GROUP COMPANY Visit unirac.com for more information.
R

Not just for sunny days.

www.unirac.com

SOLAR/GRID PARITY
HAS IT ARRIVED ?
by Jay Tyson
rid paritythe point at which solar electricity, without financial incentives, will cost the same as conventional electricity from your utilitys electric gridhas been the dream of the solar community for decades. Among many efforts to speed that up is the U.S. Department of Energys SunShot Initiative, which has a goal of reducing the cost of solar electric systems by about 75%to a little more than $1 per wattby 2020. This would make solar energy less expensive than grid energy in almost every U.S. market. However, unlike President Kennedys Moonshot program, which reached its goal the moment Neil Armstrong first set foot on the surface of the moon, the SunShot goal of grid parity will be achieved at different times depending on your location, roof orientation, the local cost of electricity, and several other factors. Indeed, it may have already arrived in some locations.

In some markets, solar-produced electricity, made right on your rooftop, is cost-competitive with utility-generated electricity.
iStockPhoto/DHuss

Determining Parity
If you know all of the details of a particular site and solar design, determining the kilowatt-hour (kWh) price point at which PV power is equal to grid power is not too difficult. Ive developed a grid parity calculator spreadsheet to assist (see Web Extras below). Dont be daunted by the 28 variables that go into this calculationhalf of these are figured already by NRELs PVWatts calculator (see http://rredc.nrel.gov/solar/ calculators/PVWATTS/version1). And all of the variables have explanations or suggested ranges, so if you dont have an exact figure for some, you can approximate, and update it later as needed.

web extra
Access the grid parity spreadsheet online at www.homepower.com/webextras.

58

home power 145 october & november 2011

iStockPhoto/alexsl

grid parity

Grid electricity is paid for as you use it, with payments stretching out forever. The majority of PV expenses are paid for at the time the system is installed. After that, the energy is essentially free.

Solar Subsidies Still Essential

There is a tendency to think that, as soon as apparent grid parity (GPA) is reached, we can do away with subsidies that are solar incentives. But this is not the case. First, it would be unfair to the solar technologies to remove these subsidies unless fossil-fuel subsidies are also removed. This includes not only the obvious subsidies, but also the hidden subsidies, such as free disposal of wastes in the atmosphere, soil, and waterways. If the government is treating all aspects of the energy industry fairly, a residual subsidy representing the difference between GPA and true grid parity (GPT) will always be required.

Defining Parity
Grid parity means that, at the end of the PV systems life cycle, you will have spent the same amount on your PV system as you would have spent on grid electricity, for the same amount of energyi.e., the payback period is equal to the life cycle. However, the nature of their costs is different. Grid electricity is paid for as you use it, with payments stretching out forever. The majority of PV expenses are paid for at the time the system is installed. After that, the energy is essentially free, with the exception of minor maintenance and insurance costs. To accurately compare the two, we must translate all of the expenses into common terms. To do that, we must choose a life cycle period for the PV system. Typically, 25 years is chosen because this is the standard length of PV module warranties. To convert the value of payments that far in the future into todays values, we calculate those amounts based on their present value. Therefore, each future payment is reduced to account for the assumed rate of future inflation. We should also distinguish between GPA and GPT. GPA is based on the actual prices that the consumer pays, both for grid electricity and for solar electricity. GPT attempts to account for certain factors that do not appear in the price. These include removing the subsidies that fossil fuels currently receive and charging for the externalities e.g., free disposal of gaseous waste into the atmosphere; disposal of wastes into streams and rivers; the costs of fossil-fuel resource wars. These are complex policy issues that may affect the future price of grid electricity. But for the purpose of the individual home- or business-owner who is dealing with real costs now, this article focuses on GPA.

Subsidies will be needed as long as there are uncertainties in any of the variables in the cost-comparison calculations. The grid parity calculator identifies three speculative variables future inflation rate, future energy-inflation rate, and the value of modules at the end of their life cycle. Since these cannot be predicted with any degree of certainty, incentives will be needed beyond grid parity to cover the cost of this uncertaintyto move the solar alternative from being probably economical to almost certainly economical. Incentives are also needed wherever PV systems are unusual or non-standard in a neighborhood. There is a natural resistance to change. Incentives beyond grid parity are needed to overcome this until rooftop PV systems become the norm. Finally, incentives are needed to encourage people to invest their money at the beginning of the life cycle rather than buying electricity with the conventional pay-as-you-use method.

Supply the PVWatts online calculator with a few valuesthe system size, derate factor, type, tilt, and azimuthand it will estimate your systems production performance.

www.homepower.com

59

grid parity

Trends in PV & Grid Residential Electricity Prices (U.S. Annual Averages)

35 30

25 20 15 10 5 0 1995 2000 Solar 2005 2010 2015 2020

Year
Grid

Cost Factors
Grid Electricity. The cost of grid electricity (variable 1 in the GP spreadsheet) can be determined by reviewing your electric bill. Simply divide the total of the generation and transmission charges by the number of kilowatt-hours youve used. Where utilities have time-of-use (TOU) rates in place, youll need to estimate how much energy your PV system will generate at various times of the day. Fortunately, PV systems often tend to hit peak production at about the same time that electricity is most expensive, so TOU customers PV systems will be producing a lot of the most valuable electricity. Where the utilitys rate varies depending on the amount of energy used (tiered pricing), the solar alternative will also replace the most expensive grid electricity you would have used and may also reach down into lower tiers as well. With both TOU and tiered rate schedules, youll need to study the system size and your usage patterns to arrive at an accurate estimate of the average cost per kWh of the electricity youll be saving. The cost per kWh may sound small (ranging between 7 cents and 30 cents in 2010), but dont let it fool youit is a big factor in determining whether or not your PV system reaches grid parity. Another major factor on the grid side of the equation is how fast the price of grid electricity will rise (variable 13) compared to general inflation (variable 12). Historically, energy prices have risen faster than overall inflation. But how much faster depends on which part of history youre looking at. Typical estimates range from 0% to 6.5% per year. Just a single percentage point or two over the life cycle of a PV system can make a big difference in the grid parity calculation. And how similar will the past be to the future? New supplies of fossil fuels are being discovered, and new methods of extracting previously uneconomic fuels are being developed. At the same time, both the worldwide

population and the per-capita energy consumption are growing dramatically, especially in India and China. Here in the United States, higher gasoline prices may push people into electric cars, placing increased demand on the electric grid. Will the growth of electrical demand outstrip the growth of supply and drive up the price? What about the cost of building additional power plants and transmission lines? How much will environmental concerns add to these costs? Will the government reduce fossil fuel subsidies? Will it add taxes to the fossil fuel industry, to reflect the true costs? Is the expansion of nuclear energy still a viable option after the crisis in Japan? All of these factors play a role predicting the future price of electricity. While I agree that its likely to be more than the general inflation figure, its hard to say how much more. Perhaps the best approach is to try a few different estimates here, and see what the cost-per-kWh needs to be to reach grid parity at these points. Solar Electricity. The cost-per-watt of solar-generated electricity (variable 2) is one of the biggest factors in determining when your system will reach grid parity. If you want the most accurate value, its best to get a quote from a local installer in your area, who can take into account any special cost factors associated with your particular site. If you need only a general idea of the recent cost-per-watt prices in your area, you can search the National Renewable Energy Laboratorys Open PV Project, and retrieve a list of local projects as a spreadsheet (see http://openpv.nrel.gov). Sort for recent, nearby projects about the same size as yours, and create a cost per watt column, which takes the total project cost on each line and divides it by the total number of watts (kW x 1,000) for that project. This will give you a good idea of local cost per wattsomewhere between $4 and $10.

Cents Per kWh

PVWatts allows users to input various values to determine an overall derate factor.

60

home power 145 october & november 2011

grid parity
the terms. For the GP calculator, always use 1.0 for the DC Rating (kW), since the system size is entered separately as variable 3. Note that Cost of Electricity is also already considered. Review and adjust as needed the first 10 derate factors according to the specifics of your system. Leave the eleventh one (age) as 1.0, since this is adjusted separately as variable 5 in the GP calculator. If parts of your array will be shaded during parts of the year, you may need to have a shading analysis done for more accuracy. After clicking the Calculate button in the PVWatts program, find the AC Energy (kWh) for the year. Results may range anywhere from 600 or less to 1,800 or so, depending on the factors. The rate at which the modules lose productivity each year is included as variable 5. This information is usually on module spec sheets, but if you dont have it, 1% is a reasonably conservative figure. Although PV systems require little maintenance, it must be accounted for. The biggest cost is inverter replacement (variable 7), which is likely to be needed 10 to 15 years after the system is installed. One replacement at the midpoint of a 25-year life cycle is anticipated. If you are counting on a significantly longer system life cycle, this variable should be increased by about 8% for each year beyond the standard 25 years. The average inverter price, on a per kW basis, can be found at www.solarbuzz.com. If your system is designed already, you can plug in the actual cost of your inverter(s) divided by your systems size in kW. Miscellany. Tree trimming (variable 8) is included for sites where tree shade is an issue. This is simply the cost of having the trees trimmed, divided by the number of years between trimmings. Initial trimming or tree removal, or purchase of solar easements, should be included as part of the original installation costs in variable 2. Occasional cleaning, plus monitoring and any out-ofwarranty maintenance costs, are lumped into variable 9. Rainy areas usually dont need module cleaning. System monitoring can often be set up for free, or nearly so. Many people have no out-of-warranty repair costs, but you might want to set aside a little something for the occasional oddball occurrence. If youre spending your own time on doing any of the above work, you can estimate its value and add that into this variable. Additional insurance costs (variable 10) should be included since it will now cost more to replace your home in the event of a disaster. Your homeowners insurance company

PVWatts provides a monthly breakdown of your PV systems production, including kWh generated and the comparative cost of the energy produced.

Another significant variable is the PV systems life cycle (variable 6). Most people will choose 25 years, since this is the length of a typical module warranty. It may also be about the same as the lifetime of the roofing material itself, especially if youve got a standard composition shingle roof. The 25year cycle assumes a single inverter replacement midway through the cycle. You can adjust the length of the cycle if you anticipate that your modules and roof will last longer or if you feel that youll need to replace the modules earlier for any reason. Early replacement might also suggest that the salvage value (variable 14) will be increased as the modules will have some warranty life left. System productivity (variable 4)expressed in kWh per kW of system sizeis also a major factor. This variable relies on NRELs PVWatts calculator (see http://rredc.nrel. gov/solar/calculators/PVWATTS/version1). This is where the location, module orientation and tilt, weather, shading, and several other site-specific conditions are considered. Explanations and typical values are provided for most of

The cost per kWh may sound small (ranging between 7 cents and 30 cents in 2010), but dont let it fool you it is a big factor in determining when your PV system reaches grid parity.

www.homepower.com

61

grid parity

Property Tax Incentives for Renewables

In some states, the additional value that the PV system adds to your home may increase your property taxes. Fortunately, several states have eliminated these taxes.

Alaska Puerto Rico Hawaii

www.dsireusa.org

State exemption or special assessment only Local governments authorized to offer exemption (no state exemption or assessment) State exemption or special assessment + local government option None

should be able to give you a figure for the cost per $1,000 of additional equipment added. In some states, the value that the PV system adds to your home may increase your property taxes. Fortunately, several states have eliminated these taxes (see map and www. dsireusa.org). Finally, we need to subtract the salvage value of the PV system at the end of its life (variable 14). It is difficult to guess how much residual value modules will have after 25 years they may have another 20 years of useful life. However, if module technology has improved greatly, and if their prices have come down significantly by the end of the life cycle, then perhaps rather than a net value, you will have a net cost of removing and disposing of them. Fortunately, this is not a major factor in either direction, so a guesstimate of 0 net value is often used here.

An Example Calculation
In my home state (New Jersey), 1 kWh from the grid costs 19 cents, and a 10 kW PV system can be installed for about $5 per watt. Facing anywhere from south-southeast to south-southwest, at tilts that are typical for roofs here (4:12 to 12:12), with no shading, and using equipment with reasonably low derate factors, I could expect to get 1,200 kWh per kW of PV modules. The productivity declines 1% per year and the life cycle will be 25 years. One replacement of the inverter at $715 per kW will add $7,150 in presentvalue dollars to the cost. Nearby trees will need to be trimmed once every four years at $600 per trim, or $150 per year, and Ive set aside $100 per year for maintenance costs$25 for my time and water spent on the annual hose-down during pollen season, and $450 for an electricians visit once every six years (something oddball, like replacing wiring that got chewed on by critters). My insurance costs an additional $1 per year for every $1,000 of equipment

Ive added, or $50 per year. New Jersey law gives property tax breaks for added PV systems, so that factor is 0%. I assume that general inflation will be 3% per year and that the cost of electricity will rise at 5% per year2% faster than general inflation. I assume that at the end of the systems life, my PV modules will be removed and sold for a residual value equal to the cost of removing the modulesi.e., the net salvage and disposal costs are zero. After plugging the data into the GP calculator, it reports that at the end of 25 years, I would have spent $367 less on the PV system (in present-value dollars) than I would have spent for the same amount of electricity from the gridjust slightly past the apparent grid parity threshold. In this case, the tax credit and incentives available would serve as motivators to switch to solar energy, but would not actually have been needed to pay for any additional costs associated with the switch. In most other areas, the cost of grid electricity has not yet reached 19 cents per kWh. But grid parity is still being reached in areas across the South and West despite lower grid electricity costs, since PV systems there receive more sunshine, increasing the annual kWh generated per kW installed, which offsets the grid electricitys cost difference. Tax credits and other subsidies help change potential solar sites from being financially marginal to financially viable. This creates demand, helping manufacturers and installers increase their economies of scale, bringing prices down further. Declining solar prices combined with increasing grid energy costs will be opening the solar/grid-parity window ever wider in the years ahead.

Access
Jay Tyson ([email protected]) is a solar planner/solar project manager living in central New Jersey.

62

home power 145 october & november 2011

Learn Solar, Buy Solar,

Accelerate Your Solar Business

Solar Training

Solar Products

Support Services

Now its as easy as 1-2-3 to power up your solar business with ONTILITY. With our solar training, products and services, accelerate your business today.

ONtility
To learn more, please contact us toll-free at 1.877.858.7479 or visit us at www.ontility.com
Solar Training Solar Products Solar Design Solar Consulting Solar Logistics Solar Marketing

Our rst twenty-four years are now available on DVD-ROM...for FREE.

eve just released the third edition of Home Powers digital archive and its yours free when you subscribe or renew for three years ($38.95 U.S.). Not available for purchase separately.

143 back issues spanning 24 years. Every page, every article. Comprehensive bookmarking and linking for easy navigation. Portable, searchable, printable PDF files on DVDROM. Adobe Reader Required.

Subscribe or renew right now at homepower.com/subscribe, by phone, or by postal order form.

Saving Water
Take advantage of modern technologies and smart-use strategies to save water.
by Claire Anderson 66
home power 145 october & november 2011

iStockphoto/Eric Delmar

water smarts
hether youre on- or off-grid, household watersaving strategies are a smart idea, both from a resource- and energy-savings standpoint. According to the U.S. Environmental Protection Agency (EPA), the average household spends as much as $500 per year on water and sewer bills. By changing the way water is used, the EPA estimates that the average household could whittle their water expenses by about 30%. The EPA says that if water-saving appliances were used in every household, more than 3 trillion gallons of water and more than $18 billion per year would be saved. The benefits are wide-reachingwhen individual households use water more efficiently, the need for establishing new water-supply infrastructure and wastewater treatment facilities is reduced. While those not on community water or sewer systems wont necessarily reap these cash savings directly, they will benefit by decreasing their well-pump run time, saving equipment wear and tear, and helping extend equipment life.

If water-efficient fixtures were installed in just 1% of U.S. homes, 100 million kWh of electricity per year could be savedcutting greenhouse gas emissions by 80,000 tons, which is equivalent to removing nearly 15,000 automobiles from the road. If old, water-wasting toilets in 1% of U.S. homes were replaced with water-efficient models, more than 38 million kWh of electricity could be saved. The savings could be dramatic, so where should you start?

Starting to Save: Indoors

According to the American Water Works Association, the average U.S. household uses 127,400 gallons of water per year. But where is all this water going? A significant portion69.3 gallons per person, per dayis used indoors. The graph (lower left) breaks down household usage by category. Flushing Toilets. Toilets are the largest water-wasters inside most homes, accounting for about 25% of the daily indoor water use. If your toilet was installed before 1992, it likely uses too much water. Check out your toilets vintage by lifting the lid and looking at the manufacturers imprint. Sometimes, the stamp will also include a gpf (gallons per flush) value, such as 2.2 gpf, which indicates the amount of water used for each flush. In 1992, federal legislation mandated that all toilets manufactured or imported into the United States be 1.6 gpf or lower. Today, you can do even betterdual-flush units let you select how much water to use, usually 0.8 gpf or 1.6 gpf. For reviews of low-flush and dual-flush models, check out expert plumber Terry Loves forums at www.terrylove.com. Although this is a commercial site, the forums offer insight on models that people love, and ones people love to hate. If youre not ready to replace your old toilet, there are modifications that can improve its efficiency. The first is a simple adjustment: On some toilets, you can adjust the tank water level by moving the spring clip on the rod that hangs down from the refill valve. This then determines how much water is needed in the tank to shut off the refill valve. Another inexpensive method is to displace some of the water in the tank with a supplemental bladder or similar device. This reduces the amount of water needed to refill the tank and the amount of water used per flush. At $10 or less, toilet bladders and dams quickly recoup their up-front costs. Of course, your toilet needs a certain amount of water in the tank to flush. Youll have to experiment to strike a balance between adequate flushing and water savings. Note: Do not try to offset water in the tank with items not designed for the purposeyou can easily end up using more water than you would without them or cause damage to your toilet. Commonly used water jugs can move around, getting in the way of refill parts. Bricks may not have that problem, but they can disintegrate into abrasive grit over time, possibly damaging the flapper valve and causing leakage. Dual-flush retrofit kits are available to make your old toilet more efficient. Youll need to have some mechanical skills to tackle this project, since some of the units involve removing

Save Water, Save Energy

A lot of energy is spent to treat and convey water to our homes. According to the EPAs WaterSense program, public water supply and treatment facilities consume about 56 billion kilowatt-hours (kWh) per year to convey water from the source to the sink. In a household connected to a public water supply, letting your faucet run for five minutes wastes about 12.5 gallons and uses about as much energy as burning a 60-watt lightbulb for 14 hours. Curbing your household water use translates into reduced energy demands in supplying and treating public water supplies, which also translates into less pollution, since most of the energy in the United States is generated with fossil fuels. WaterSense also says that:

Average Annual Water Use

Outdoor:* 30%

Toilets: 19%

Other: 4% Leaks: 9% Clothes Washers: 15% Faucets: 11% Showers: 12%

*As much as 70%, depending upon region and season. Source: WaterSense, U.S. EPA

www.homepower.com

67

water smarts
and then reinstalling the toilet tank. For $25 to $50, they are a significantly cheaper option than buying a new dual-flush unit. Plus, youll avoid putting another toilet in the landfill (though many regions have toilet recycling programs). A clever toilet-water reduction conceptthe toilet-top sinkuses reclaimed hand-washing water for flushing. Upon flushing the toilet, water flows automatically from the sinktop faucet, allowing ample time for hand-washing. The hand-washing water is then routed to the toilet bowl via the overflow pipe. The light graywater can then be used a second timefor flushing. Besides reusing water, toilet-top sinks offer a germ-reducing advantagesince water flows from the faucet automatically, theres no need for touching the fixture. Composting toilets are the most water-efficient of all, since they use no water. They typically consist of a standard seat that empties into a chamber. Deposits are usually covered with peat moss, coconut husks, or sawdust to stymie odors and aid in composting. Once full, the chamber contents can be emptied into a separate, outdoor composting bin or buried around vegetation.
If youre handy, dualflush retrofit kits are a fraction of the price of a new dual-flush toilet, but offer similar water savings.

Water that does double-duty: This toilet-top sink routes handwashing water to the bowl via the overflow pipe, where it is reused for flushing.

The simplest system is a sawdust toilet. Popularized by Joe Jenkins, author of The Humanure Handbook, it consists of a 5-gallon bucket, sawdust for cover material, and an outdoor composting bin. When the bucket is full, it is emptied into an outdoor composting bin with other yard and food scraps to finish decomposing. While most composting toilets dont use water, some commercially produced composting toilets use electricity to run fans or small heaters to evaporate excess moisture. Be sure to check out these requirements before you buy. In some areas, so long as you have a flush toilet or septic system installed, a composting toilet may be allowed. Check with your local building authority, human health services office, or department of environment.

Courtesy Sink Positive

Annual Toilet Water Usage

8,000

Gallons Per Year

6,000

4,000

2,000

0 3.50 1.60 1.28 1.00

68

home power 145 october & november 2011

Courtesy One2Flush

Gallons Per Flush

water smarts
You can get a list of Energy Star-rated clothes washers from www.energystar.com. But if youre interested in seeking out higher-efficiency units, the Consortium for Energy Efficiency has developed even more stringent ratings through its CEE Super Efficient Home Appliances Initiative. You can download its list of qualifying clothes washers from www. cee1.org. Front-loading clothes washers are a bit more expensive than top-loaders, but users will usually recoup the additional up-front cost in a year or so of water and energy savings. Plus,
iStockphoto/Dominik Pabis

Dishwashing: By Hand or Machine?

Comparing the efficiency of hand-washing versus using an automatic dishwasher is a difficult, if not fairly impossible task, since it all boils down to user habits. A water-miser who uses one basin for lukewarm wash-water and another basin filled with cold for rinsing may come closest to beating or even exceeding a dishwashers energy and water use. But most studies and sites conclude that if you run your dishwasher when its full, a dishwasher is likely to be more efficient. At the University of Bonn in Germany, one study measured the dish-washing habits of 113 people from seven different countries, and found that water use from hand-washing dishes varied considerably. The study grouped individuals as superwashers (the people who preclean, soap clean, and rinse); economizers, who put soap on a sponge, using as little water as possible; and carefree washers, who were profligate water and soap users. In the study, each person washed 12 place settings. On average, hand-washing used 27 gallons of water and 2.5 kWh of water-heating energy. The automatic dishwasher used approximately 4 gallons of water, and consumed 1 to 2 kWh of total energy, which agrees with U.S. DOE statistics on Energy Star-rated dishwashers water and energy usage. Whatever method you usemanual or automatichere are some tips for saving water and energy when it comes to dishwashing: Remove large food scraps before you wash. Dont delay, if youre hand-washing. Skip pre-rinsing the dishes under running tap water, whether washing them by hand or in a machine. Manual dishwashing is best in two sinks: one with hot water and detergent; the other with cold water for rinse. Use the amount of detergent recommended by the manufacturer. Run your dishwasher with full loads only. Use your dishwashers air-dry feature instead of its heatdry cycle. Use a dishwasher thats fairly newmade in the past few years. Some newer units also have booster heaters that heat the water on demand versus from your water heater, helping save energy.

Front-loading (horizontal-axis) washing machines offer both water and energy savings, compared to a conventional verticalaxis washer.

Washing Clothes. The average U.S. family washes almost 400 loads of laundry each year, according to the U.S. Department of Energy. After toilets, washing clothes consumes the most water in a typical household. This is mostly due to older verticalaxis machines (commonly known as top loaders), which may use 35% to 50% more water than newer horizontal-axis machines. If your machine is 10 years or older, you may want to consider replacing it for both water and energy savings. Choose a model with a high modified energy factor (MEF) and a low water factor (WF). MEF is a measure of energy efficiency that considers the energy used by the washer, and the energy used to heat the water and run the dryer. More efficient washing machines have high MEFs. WF measures water efficiency in gallons of water consumed per cubic foot of capacity. The lower the WF, the more water-efficient the clothes washer.

www.homepower.com

69

water smarts
Modern low-flow showerheads include atomizers that deliver water in many small droplets to cover lots of area; pulsators that vary spray patterns; and aerators. Some watersaving showerheads come with valves to reduce or stop the water flow while youre lathering up. Faucets. Low-flow faucets designed to federal standards may use sensors, as well as aerators, to reduce water consumption. For households, one of the newest innovations is the touch faucet, which allows users to control flow and operation with a quick touch of the faucet. Fixture retrofits include simple and inexpensive aerators, which screw into the end of the faucet. At $5 to $10, they are an easy, quick retrofit that offers a quick payback. Total flow adaptors can also help save water by easily allowing you to shut off the tap while sudsing your hands or brushing your teeth, for example, while keeping the water temperature setting the same. Foot controls allow homeowners to activate a faucet at a set temperature by tapping their foot to a pedal (or pedals), which control hot and cold taps. Although they can save water, most units require electricity to operate, however minimal it may be. Find & Fix Leaks. The EPA projects that 36 states are expected to face varied levels of water shortages by 2013, which makes water conservation essential. It also reports that water leaks may now account for more than 1 trillion gallons of water wasted each year in U.S. homes. Studies have shown homes can waste more than 10% due to leaks, which costs both you and the environment. If youre on metered water, you can figure out if your home is a water waster by checking the meter over a two-hour period when no water is being used. If your meter registered that some water flowed during that period, you likely need to track down leaks. Before you start sleuthing, be sure to locate your main water shutoff valve, which controls all of the water coming into your house. Knowing where this is located will be helpful if you locate leaksyoull be able to determine whether the leak is inside the house or lies before the main shutoff. Leaky toilets can account for 95% of all water waste. Defective float arms and flapper valves are common causes of toilet leaks. To see if the float arm is working properly, remove the toilet lid, flush, and listen. The tank should refill and the water should shut off. If it doesnt, you may need to make adjustments to the arm or replace the float. Worn or obstructed flapper valves are another common problem that can cause your toilet tank to drain and refill continuously, and can waste up to 200 gallons per day. You can check for flapper valve failures by adding a few drops of food coloring to the tank water. If theres a leak, youll see colored water in the bowl within 15 to 30 minutes. First, make sure the chain from the handle to the flapper is not getting in the way of the flapper closing. Then, make sure that the surface of the flapper and its seat are smooth and not obstructed.

Aerators are an inexpensive, easy retrofit that can provide water savings in a snap.

some utilities and local or state governments offer rebates for purchasing efficient clothes washers to offset higher costs (see the Energy Star website and www.dsireusa.org for more information). Faucets & Fixtures. The fourth largest household water consumer (behind outdoor use, toilets, and clothes washers) is at the tapkitchen and bath faucets, and showers. Of course, user behavior is tantamount to water-saving success. Things like shutting off the water while youre brushing your teeth and taking shorter showers are water-saving behaviors that a water-efficient fixture will help, but not shape. According to the U.S. Department of Energy, federal regulations stipulate that new showerhead flow rates cant exceed more than 2.5 gallons per minute (gpm) at a water pressure of 80 pounds per square inch (psi). New faucet flow rates cant exceed 2.5 gpm at 80 psi or 2.2 gpm at 60 psi. Using these new fixtures can help boost your overall water savings by 25% to 60%. Showerheads. For maximum water efficiency, select a showerhead with a flow rate of less than 2.5 gpm. Two basic types of low-flow showerheads are available: aerating, which mixes air with water; and laminar-flow, which forms individual streams of water. Laminar-flow showerheads put less moisture into the air compared to aerating ones. Consider replacing showerheads that are more than 9 years oldbefore the water-saving standards went into effect. To determine how many gallons per minute your showerhead uses, you can place a bucketmarked in gallon incrementsunderneath the fixture. Next, turn on the shower at its normal setting. Record how many seconds it takes to fill the bucket to the 1-gallon mark. For instance, if it took 15 seconds to fill the bucket to the gallon mark, your showerhead would have a flow rate of about 4 gpm.

70

home power 145 october & november 2011

iStockphoto/BanksPhotos

water smarts

Courtesy Associated Landscape Contractors of Colorado Awards program

Low water-use (xeriscaped) landscapes can be lush and full of color, as this photo of a xeriscaped yard in Colorado shows.

Leaky faucets are another common water-waster. A worn seat washer may be the cause of a dripping faucet. It can be replaced with a few simple tools. Sometimes, parts for washerless faucets can be difficult to find or expensive, so it may be more cost-effective to replace the entire faucet.

Outside the Home

Most household water useabout 30%occurs outside the home, and goes toward watering lawns, landscape plantings, and gardens. The EPA estimates that more than 7 billion gallons a day are used for these purposes. Some estimates report that up to 50% of commercial and residential irrigation water is wasted, due to evaporation, wind, improper system design, or overwatering. Irrigation. Most people love their lawns too much, watering too often and for too long. Give your lawn the step test: If the grass springs back readily, it can wait awhile for watering. Avoid sprinklers and overhead watering systemsthey are big water wasters, losing a lot of water to evaporation. If you have an irrigation system, check it thoroughly before putting it back in business. Its estimated that, with regular maintenance, watering waste due to irrigation systems could be reduced by about 15%. Irrigation systems can be large water wasters. Inspect your sprinklers and drip sprayers regularly for leaks, and do so during the daytime, when youre not watering.

A telltale sign of a malfunctioning irrigation system is soft, mushy spots in your lawn. Water during the early morning or late evening, when evaporation will be lowest. Consider installing soil moisture sensors, which sense the amount of water in the ground thats available to plants. Sensors can be connected to an irrigation system to automatically water when its needed. Lose Your Lawn. Getting rid of your turfor reducing its sizeis one way to drastically reduce your household water use. Consider replacing grass with drought-tolerant and native plants. Once they are established, theyll need little watering beyond normal rainfall. Native plants usually have the added benefit of being more pest- and disease-resistant. Xeriscaping is the practice of using water-conserving principles in the landscape so that supplemental watering is greatly reduced or eliminated. It includes using drought-tolerant plants and efficient irrigation equipment, such as subsurface irrigation systems or drip irrigation systems; minimizing turf areas; harvesting rainwater; and using mulch and soil amendments to slow evaporation and hold the water in the soil. Saving the Rain. Beyond water conservation, consider water harvesting strategiesways to keep water on-site and reduce stormwater runoff.

www.homepower.com

71

water smarts
0.90 = system loss factor 7.5 = conversion factor (gal./ft.3) Example: One 60-gallon barrel would provide runoff storage from a rooftop area of approximately 215 square feet for a 0.5-inch (0.042 ft.) rainfall. 60 gal. = 215 ft.2 0.042 ft. 0.90 7.5 gal./ft.3 For long-term water storage and in areas that receive only seasonal (not year-round) precipitation, larger storage tanks are appropriate. Tanks can be sized using the same formula. For instance, in some parts of Oregon, rainfall is limited to the winter months. For example, one area averages 18.37 inches of precipitation, but most of it (14.87 inches; 81%) falls within a span of seven months. Lets say were harvesting rain from an average-sized homes roof, in this case, 2,169 square feet, for a little more than half of the year . Using the formula, 2,169 ft.2 x 1.24 ft. x 0.90 x 7.5 gal./ft.3, wed be able to collect about 18,154 gallons during that time periodand need some big cisterns to store it all! Cisterns can be constructed on-site or pre-manufactured in a range of capacities (and prices, depending on the material).

Reuse: Graywater in the Landscape

Graywater (or greywater) is water discharged from bathroom showers and sinks, washing machines, and kitchen sinks. In some areas, this water is permitted to be conveyed separately from toilet water (blackwater), and can be used in the landscape. If you compost your food scraps, dont use a garbage disposal, and avoid chlorine and other harsh chemicals, you can safely reuse all of your graywater. However, in most areas
Courtesy HOG Works Pty Ltd.

Rainwater H2OGs innovative modular vessels store a maximum amount of water (51 gallons each) in a minimal footprint. Easy connections mean design flexibility and lots of storage capacity.

Graywater from this washing machine is directed through the movable drain hose to water fruit trees (olive/pomegranate, orange, fig, and white sapote) in the landscape. The drain hose is placed in a different pipe with every load of laundry.

V = A2 R 0.90 7.5 gal./ft.3 where: V = volume of rain barrel (gal.) A2 = collection area of roof (sq. ft.) R = rainfall (ft.)

72

home power 145 october & november 2011

Brad Lancaster www.harvestingrainwater.com

Rain barrels, which connect to the downspouts of your home, are some of the simplest (and least expensive) rainwater-saving devices. Most barrels are designed to hold 40 to 75 gallons, and prices usually start at $50. In areas with consistent rainfall, rain barrels can provide some backup water for hand-watering and limited garden watering. Planning for overflows is important, as even as little as 1/4 inch of rain falling on an average-sized house can easily fill two 100-gallon rain barrels. Rain barrel volume can be determined by calculating the rooftop water yield for any given rainfall, using the following equation:

water smarts
where graywater use is allowed, only subsurface irrigation systems are permitted, preventing users from coming into contact with the water. Untreated graywater should never be stored, as it can quickly become anaerobic and carries the risk of pathogen transmission. For specific, no-nonsense recommendations for designing and implementing graywater systems, visit Art Ludwigs website at www.oasisdesign.net and read his detailed books, Create an Oasis with Greywater and Builders Greywater Guide. The simplest graywater system that is now allowed in parts of Arizona and California is highly effective and simple. The branched drain-to-mulch basin system routes graywater directly from a washing machine to a filter and then to a pipe that empties into a large basin filled with a thick layer of mulch. Typically, a tree or other planting is established in the mulch basin. More complex subsurface distribution systems can also be used, but at a higher price. Residential graywater system regulations vary from region to region. Call your county health department, and your local building or plumbing authorities, to determine what systems, if any, are allowed. Locations lacking specific graywater guidelines sometimes allow new systems under an experimental systems clause. A handful of states have rules governing residential graywater systems. If your state doesnt have any rules and you want to pursue a system, consider sharing the Arizona code rules with your permitting agency to start a dialogue, recommends graywater expert Ludwig.

Access
Home Power Managing Editor Claire Anderson (claire.anderson@ homepower.com) is tackling further water-conservation efforts to optimize her homes efficiency. Planned projects include a xeriscaped garden and a rainwater catchment system.

Off-Grid Specialists in Solar, Wind & Remote Power

Design,Sales,InstallationandSupportforDo-It-Yourselfers
Over 10 years off-grid installation experience Ove Packaged systems, fully programmed and Solar-powered emergency battery backup Customer Service Monday - Saturday ready for operation

Renewable Energy, Pure and Simple

Get answers from people who live with renewable energy:

Toll free: 888-782-0706

www.apxsolar.com
www.homepower.com

73

Why I switched to SunWize

42.3kW system Department of Public Works building, Town of Sand Lake, NY

We can attribute the success of Monolith Solar to the dedicated staff at SunWize, in particular Mona Ropkopf, who is forever accommodating. The product is there when we need it and at a competitive price.
Steven Erby, Owner/President Monolith Solar Associates, LLC www.monolithsolar.com

Visit SunWize at Booth 2608 in Dallas at Solar Power International 2011

Visit www.sunwize.com/difference or call us at 800.817.6527 and find out how switching to SunWize can help your business be successful.

2011 SunWize 800.817.6527 www.sunwize.com

Heat & Energy

RECOVERY VENTILATORS

The heat recovery ventilator (HRV) and its close cousin, the energy recovery ventilator (ERV), can often make a home more efficient. Find out here what these boxes do and if your house needs one.

by Neil Smith

Exhaust Fan

Filters

Air-to-Air Heat Exchanger

Intake Fan

A heat recovery ventilator (HRV) or energy recovery ventilator (ERV) is an important component for keeping the air fresh in a tightly sealed energy-efficient home.

Co

e urt

sy

So

ler

a &P

lau

US

76

home power 145 october & november 2011

air quality
Homes Need to Breathe
A house built to modern standards of tight construction will allow only a very small amount of outside air to leak in. But fresh air is needed to dilute the products of human habitation (cooking, cleaning, breathing, combustion, etc.), as well as the chemicals that offgas from building materials, such as particle board and paint. According to the U.S. Environmental Protection Agency, indoor air pollution levels are as much as five times higher than outdoors. And good ventilation is an important part of maintaining good indoor air quality. Dilution and at-source (spot) exhausting are the main methods for ensuring good indoor air quality. It is possible to remove particles (by filtration), volatile organics (by adsorption), and other harmful products from indoor air, but these technologies are energy-intensive and very expensive (think spacecraft and submarines). Although houses can be designed to self-ventilate, this process depends upon local climate conditions and wind shadingprotection by tall walls and treeswhich are not controllable. So the practical choice for many of our homes is mechanical ventilation. Why not just open the windows? In some very mild climates, this might be a fine strategy. But in most of the United States, trying to ensure adequate air exchange defeats the energy-saving intent of a well-sealed building envelope. The energy cost of exhaust-only or natural ventilation versus energy recovery ventilation can be easily demonstrated. Take a 2,500-square-foot house with indoor conditions of 70F and 40% relative humidity, and outside air conditions of 30F and 50% relative humidity. If we ventilate the house with 120 cubic feet per minute (prevailing wisdom of 0.35 air changes per hour) of outside air (as compared to no fresh air at all), here is how much the ventilation will cost us per month. This is due to the additional heating energy required because of the ventilation. 120 ft.3/min. 60 min./hr. (25.3 Btu/lb. 9.06 Btu/lb.)* 0.074 lbs./ft.3 1.25 efficiency 24 hrs./day 30 days/mo. (1 105 therms/Btu) $1.50/therm = $116/mo. *Enthalpy of indoor vs. outdoor air (see psychrometric chart) If we provide the same amount of ventilation, but instead of using exhaust fans only, we recover the airflows through an HRV/ERV with a recovery rate of 70%, the monthly heating cost drops to $35. An HRV/ERVs only energy input is electricity to run the fans. For this situation, using average residential electricity costs, the monthly cost to run the HRV/ ERV would be approximately $12. The average power draw of an HRV/ERV is 150 watts. If it runs 24 hours a day for 30 days each month, then the monthly energy consumption would be 150 W 24 hrs./day 30 days/mo. 1 kW/1,000 W = 108 kWh/month HRVs and ERVs use a fan to bring in outside air and another to exhaust air, balancing the amount of air in versus out. This air balance minimizes airflow through the building envelopeby reducing the pressure differential between inside and outside. While doing this, they recover energy from the outgoing airstream via a heat exchanger, which allows heat to move between the two airstreams without mixing or cross-contaminating them. During the heating season, warm inside air is exhausted and pulled through the heat exchanger, while a separate fan brings in cold outside air. The outside air is warmed by the heat of the exhaust air. During the cooling season, the opposite occurs. ERVs take this energy recovery a step further by allowing moisture transfer between the two airstreams. If heat recovery is such a good idea, why not recover the heat from every exhaust source, like clothes dryers and

HRVs and ERVs are sized based on a homes square footage and the desired air exchange rate.

Courtesy Fantech

According to the U.S. EPA, indoor air pollution levels are as much as five times higher than those outdoors.

www.homepower.com

77

air quality
Airflow through HRVs and ERVs transfers heat, while replacing stale air with fresh, functioning in both heating and cooling seasons. (Heating season function shown by flow arrows.)

Fresh Air From Outside

Exhaust Air From Inside

Exhaust Air To Outside

Courtesy Fantech

Fresh Air To Inside

cook stove hoods? This is definitely not recommended or permitted. Both sources have contaminants in the airstream that will foul the heat exchanger and decrease its efficiency. Furthermore, there are fire risks associated with cooktops and their combustion products. The heat recovery potential from an intermittent exhaust source is negligible, since residential appliances do not continuously run. HRV/ERVs should be used in any new, tightly sealed home. Most older houses are so leaky that they self-ventilate. Although an HRV/ERV can improve ventilation within a leaky structure, it cannot be expected to save a significant amount of energy, since the unplanned ventilation will still occur.

effects are diluted, and we must ventilate to reduce common pollutants (such as formaldehyde found in some building materials) that may not be detectable by the human nose. Many ventilation codes are minimums, based upon ASHRAE standards. Each code or standard will yield different airflows, but none take into account building materials that may offgas more than others, nor outside air quality, which can vary depending on your locale (local outdoor pollution). To help ensure the best indoor air quality, it is prudent to size airflow liberallyusing the standard that results in the most air exchanges. Most HRV/ERVs have multiple speed settings, so airflow can be easily changed as needed. Unknowns include what the inhabitants do. Since airflow recommendation minimums are largely based on occupant loads, a sparsely populated house will likely require more ventilation for building material toxins. A house full of people who cook, bake, and take lots of showers will have its ventilation requirements set by the need to reduce humidity and carbon dioxide. The standards are minimums, so size your system generously. Before designing whole-house ventilation, remove contaminants at the source (spot exhaust ventilation) with

A closeup of the air-to-air heat exchanger core.

The purpose of ventilating a building with outside air is to dilute the odors, chemicals, particles, and humidity that are introduced by human activities and offgassed by building materials. If we can also exhaust fouled air at the source, the ventilation system can be more efficient. When the outdoor conditions are right, we can even reduce unwanted humidity by introducing more outside airtypically during the winter. There are various recommendations for sizing mechanical ventilation systems. An older one called for 0.35 air changes per hour (ACH). Alternate recommendations are based upon a recommended airflow per room. Recommendations vary by manufacturer, but the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), which sets standards for good residential indoor air quality, recommends continuous ventilation of 0.01 cfm per square foot of living space, plus 7.5 cfm per person. So a 1,500-squarefoot home with four residents would require 45 cfm. Its difficult to measure indoor air quality without expensive tests. Rigorous testing would consist of air sampling and analysis by a laboratory. However, a smell test can provide at least the first level of measurement. Since our olfactory system readily acclimates itself to new odors, its important to test the air after being out of the house. However, with lower occupant density (bigger houses), bioeffluent (contaminants generated by the human body)

Inside: Fresh Air to Room

Outside: Stale Room Air (exhausted to outside)

Outside Air Stale Room Air

78

home power 145 october & november 2011

Courtesy Soler & Palau USA (2)

Assessing Airflow

air quality

Dealing with Wintertime Dryness

The air inside most houses is drier in the winter because homes are leaky. Cold air has very little capacity to absorb moisture. Take a situation where the outside air is at 40F with a relative humidity of 50%. As that air moves into your house and is warmed to 70F, its relative humidity changes to just 16%. How did that happen? The actual amount of moisture in the air did not change. This is reflected on the Y-axis of the graph labeled Humidity Ratio: Grains of Moisture per Pound of Dry Air. The term relative humidity (RH) is a percentage of how much moisture the air could hold at saturation (for example, right before it rains). Dew point is the temperature to which the air must be cooled for condensation to happen, or in other words, 100% relative humidity. This is best illustrated by a psychrometric chart. The type of heating system does not affect a homes RH levels. Hydronic (hot water) or hot air systems will not dry the air out. With few exceptions, these are closed systems and do not add or subtract humidity from the building air. On the other hand, a very tight house without outside air ventilation may end up with moisture issues, such as condensate on windows and doors. This is because in the absence of any significant outside air entry into the building, moisture levels increase in what is effectively a closed system. Condensation occurs when the temperature of a surface is below the dew point of the air. Typically, this happens on windows, since they have the lowest thermal resistance and therefore are the coldest surfaces. Room condition No. 2 shows the air temperature at 70F and 50% RH. To illustrate the dew point of this air, a horizontal line is drawn to the left until it intersects the 100% RH curve. This shows that the dew point is about 50F. So a surface at or below 50F will have condensation on it from moisture in the air.

Psychrometric charts show the properties of air and water mixtures for the conditions that we encounter in our environment. This chart shows two conditions: cold outside air entering a house and the effects of heating that air.

Inside Air Conditions Outside Air Conditions

www.homepower.com

79

air quality
fans over kitchen ranges and in bathrooms. Allow enough ventilation for peak loads. Bathroom ventilation should be sufficient to avoid condensation on surfaces at any time. Kitchen ventilation must have enough draw to capture the majority of smoke and odors at the source. Continuous low-level ventilation that is good on average wont be suitable. Make sure the ventilation systems are quietotherwise occupants will only use it under the most extreme conditions. HRV/ERVs cannot be expected to handle the peak odor, smoke, and humidity loads from bathrooms and kitchens. Direct-mounted fans or in-line fans, which are acoustically preferable, should be used.

INSTALLATION OPTIONS

Exhaust Air From Baths

Fantech (3)

Bath
Fresh Air To Bedrooms & Living Room Via HRV on Furnace Duct

Bedroom

Kitchen

Living Room

HRV or ERV?
The decision of whether to use an HRV or ERV can be confusing. Traditional wisdom suggests ERVs in climates where there is a significant mechanical cooling needed and dehumidification is required, such as in the Midwest, in the eastern United States, and the Southeast. During summer, its desirable to retain the coolness and the aridity of the inside air. Moisture and heat from incoming outside air is transferred to the exhaust airstream, and the ERV becomes a cool recovery ventilator. Well-sealed houses in heating-dominated climates can experience high indoor humidity levels. Therefore, HRVs are recommended, since additional moisture isnt usually desired. ERVs take the process of recovering energy in the exhaust air one step further. Besides capturing the sensible heat (energy used to raise or lower the temperature) of the air, an ERV transfers latent heatthe energy that is used to add or subtract moisture from air. Typical examples of this are dehumidification and humidification. The ERV recovers the latent heat by allowing moisture to travel across its core. Similar to heat flow, the path is from high humidity to low humidity. A situation in which an ERV is more useful than an HRV would be energy recovery during the summer months. Your
Exhaust Air From House Via HRV on Furnace Duct

GOOD: Simplified Installation Using Existing HVAC Duct and Premium Bath Fan

RTS3 Control

Bath

Bedroom

Fresh Air To Bedrooms & Living Room Via HRV on Furnace Duct Exhaust Air From Baths & Kitchen

Kitchen

Living Room

EDF1 Control

BETTER: Partially Dedicated Installation

Ways to Improve IAQ

Reduce the release of pollutants Use nontoxic, natural cleaning products (vinegar and baking soda, for example) Use and store paints, stains, and glues outside of the home Do not smoke Make sure your gas and wood-burning appliances are properly vented Make sure you have proper spot-ventilation for cooktops and stoves, and in bathrooms
Fresh Air To Bedrooms & Living Room Exhaust Air From Baths & Kitchen RTS3 Control

Bath

Bedroom

Kitchen

Living Room

EDF1 Control

BEST: Fully Dedicated Installation

80

home power 145 october & november 2011

air quality

Climate Zones for HRVs & ERVs

Courtesy Fantech

Subarctic Very Cold Cold Marine Mixed-Dry Hot-Dry Mixed-HumidERV or HRV Hot-HumidERV recommended HRV recommended

air conditioner has worked hard to dehumidify the inside air. The outside air is hotter and more humid than the inside air. As the ERV exhausts inside air and brings in outside air, two processes are at work. The outside air transfers some of its sensible (temperature) heat to the exhaust air, since the exhaust air is colder. At the same time, the outside airstream transfers some of its moisture to the exhaust airstream. In this way, the air exiting the ERV is cooler and less humid than the outside air. You could call this a cold recovery and arid recovery unit. If ERVs do all that HRVs can, then why not always use ERVs? The heat and/or moisture exchanger is typically referred to as the core. Its more difficult (thus more expensive) to fabricate an ERV core, which exchanges moisture as well as heat. Also, since these cores are moisturepermeable, they do not have the longevity of the plastic or aluminum HRV (heat-only) cores.

Configuring the System

Combining the HRV/ERV system with the existing air distribution system may be the only alternative for existing homes. Depending upon the design, the furnace or airhandling unit may have to run in conjunction with the HRV/ ERV, which could add considerably to energy usage. For homes that rely on a central air heating/cooling system, the method I prefer is to run every piece of ducting to the HRV/ERV. This means that the duct arrangement looks like an octopusalthough its not elegant on the surface, the advantage is that the flow to/from intake or supply

grilles can be controlled from a central location, with more precision. Oversize the legs and add a balancing damper (a manually operated butterfly damper) to each. Choose oversized insulated flex duct to minimize pressure drop and keep the system quiet. The grilles should be generous to reduce air noise. The outside air ducts (exhaust and intake) should be separated by several feet to prevent cross-contaminating the airflows. Place the outside air intake high enough above grade, so that the HRV/ERV isnt bringing in excess humidity or dirt and dust or be blocked by snowfall, and locate it away from exhaust vents. Another option is to run a dedicated duct system for the HRV/ERV. This arrangement may be the only choice for houses without other air distribution. A technique that I favor is to pull exhaust air from one or more bathrooms. The HRV/ ERV is sized so that it runs continuously, but at a low speed, and can be speeded up from a bathroom-mounted override switch. Each bathroom should have at least 75 cfm (preferably 100 cfm) of airflow to allow for peak exhaust requirements. Using an HRV/ERV with bathroom air input will eliminate the need for bathroom fans and provides balanced ventilation. Otherwise, ventilation will not be controlled. Some advanced technologies offer further efficiency improvements, such as a defrost function. Although more expensive, they may be appropriate, depending upon the building requirements and the efficiency goal. In conditions of severe cold, HRV/ERVs may require defrosting. This situation occurs when very cold outside air brings the temperature

www.homepower.com

81

air quality
of the exhaust air down so far that the moisture in the air condenses and freezes. The frost level will eventually build up and block airflow. Manufacturers address this in one of two ways. The simple method is to turn off the fresh air fan for a few minutes. In this way, warm inside air remains warm, flows through the HRV/ERV, warms the core, and thereby defrosts the unit. A more sophisticated method uses a fifth port and a series of operable flaps. This method forces inside air through the core and back to the house. This method is recommended in climates with severe cold, since less heat is wasted. One manufacturer claims that its ERV does not require a defrost cycle due to the efficiency of its moisture transfer. Units with electronically commutated motors decrease the full load power by about 30%, and can reduce part load power consumption by about 75%. Such units are appropriate where the HRV/ERV is the sole source of ventilation and must run continuously. Typically, most existing houses are so leaky that an HRV or ERV is pointless. For new construction, the installation cost of an HRV/ERV is not much more than the cost of the equipment ($550 and up), so long as the duct runs and installation are planned from the beginning. Properly applied, HRV/ERVs are a great way to improve indoor air quality by introducing outside air, while recovering much of the energy in exhaust air. Although there is a higher capital cost compared to simple exhaust fans, the HRV/ERV system will save energy (and money) over the long term, while providing a quieter, healthier indoor environment.

Introducing SunPumps SDS-T Series Solar Submersible Pump Line

Low Cost Super Strong Ryton and Stainless Steel Construction Fits In a 4 Well Flow Rates Up to 3 GPM and Heads Up to 230

The SDS-T Series Pumps are $595 with Complete Solar Pump Systems starting at $1660. For a limited time, mention this ad and receive a 15% discount.
SCP SERIES

Access
Neil Smith ([email protected]) is a professional mechanical engineer. Neils interests include HVAC and energy efficiency, and he currently runs the AirScape whole-house fan company. HRV/ERV Sizing Calculator www.hvacquick.com/sysbuilder/hrvbuild. php Residential HRV/ERV Manufacturers: Carrier www.residential.carrier.com Fantech www.fantech.net Lennox www.lennox.com Nu-Air www.nu-airventilation.com Soler & Palau USA www.solerpalau-usa.com/res_rv.html UltimateAir www.ultimateair.com

SunPumps offers a variety of DC Pool Pumps ranging from HP to 1 HP. Complete Solar Pool Pump Systems are available. Call for a free system sizing and quote.

POOL PUMPS

Complete Solar Pumping Systems ranging from 1/4 HP up to 3 HP for our standard pump line and up to 30 HP for our custom solar systems.

Phone: Fax:

1-800-370-8115 (928) 348-9652 (928) 348-9653

www.sunpumps.com

82

home power 145 october & november 2011

Harvest the power of the

Season after season, the sun gives its light to the earth, allowing life to bloom. Every day a limitless crop of free, clean energy reaches our planet. Stiebel Eltron manufactures all the tools you need for a successful thermal solar harvest. And weve been doing so since 1976. From our highly efcient at plate collectors and storage tanks to our complete line of mounting hardware, pump stations, controllers, and accessories, we have it all.

Sun
2 x SOL 25 PLUS Flat Plate Collectors

Stiebel Eltron is your one stop source for thermal solar products.
SOLKIT 2 includes:

Pump station with SOM 6 Controller

Because every installation is different, we have a full line of SOLKITS and mounting hardware kits available. All components and accessories are available for individual sale.

Simply the Best

SBB 300 Plus Storage Tank

SRCC OG300 Certied

TOLL FREE

800.582.8423

www.stiebel-eltron-usa.com

BACKWOO DS SOLAR 2011-2012

Planning Guide & Catalog

Less Work, More Energy.

A sealed, maintenance-free battery to power your needs!
Superior Capacity - To meet your daily energy needs High Quality Product - For long battery life Maintenance Free - No watering Non-spillable and Non-hazardous - Clean and Safe Operation Your Clean-Green Energy Solution
For more info contact us:
*5 Year Warranty applies to certain models used in select applications only. Please see fullriverdcbattery.com for more information.

s a l e s @ f u l l r i v e r d c b a t t e r y. c o m | 8 0 0 - 5 2 2 - 8 1 9 1 | w w w. f u l l r i v e r d c b a t t er y.com

84

home power 145 october & november 2011

Well, proven performance sure helps.

Who says you can't predict the future?

PROVEN PERFORMANCE AND BANK ABLE QUALIT Y

Since 1958 SCHOTT Solar has lead the way in solar technology. Over the years SCHOTT Solar has combined the know-how of German engineering with American production. Each solar module combines state of the art performance with extreme durability, ensuring 90% performance even after 25 years. Thats solar quality you can bank on. For more information visit www.schottsolar.us To become a dealer, call 800.977.0777

Renewable Retrofit
Story & photos by Stephen Hren

for a Small, Off-Grid Office

The Abundance Foundations PV-powered, solar-heated, off-grid office.

hen you think of the word office, what usually comes to mind is a sterile cubicle in a large boxy building surrounded by a parking lot, totally dependent on fossil fuel infrastructure for its existence. But when youre a nonprofit organization like The Abundance Foundation (TAF) in Pittsboro, North Carolinaeducating people about sustainability through workshops, green tours, and local food and renewable energy eventsresiding in such sterile surroundings goes against your mission. You want to create an office of the future.
86

home power 145 october & november 2011

off-grid office
Building Renovation
The group was starting to feel cramped in the existing space, an office shared with Piedmont Biofuelsa local biodiesel cooperative (see HP122 and HP132) that was expanding and needed to occupy more of the converted warehouse for its own employees. TAF employees imagined an office that would help showcase the organizations commitment to sustainability something beautifully crafted using locally sourced lumber, powered by renewable energy, and situated on the edge of the organic farm that surrounded the property. As luck would have it, a 10- by 12-foot screenedin sleeping shed, intended to house summer interns for the organic farm, was sitting unused. TAF moved the building close to the existing quarters so the staff of three could use the kitchen and bathrooms in the adjacent structure. The small building was large enough for an office, yet small enough to make heating and cooling relatively easy. TAF hired local designerbuilder Green Door Designs (GDD) to retrofit the small structure for year-round occupancy. GDD built the block foundation, and used local, Forest Stewardship Council-certified lumber to build out the frame.

TAFs three work stations, designed with forethought and attention, use a scant 1.8 kWh per day.

Window Shopping
One crucial mistake was not paying enough attention to the coatings on the double-pane windows. The windows were purchased new at a reuse center but no longer had the National Fenestration Rating Council (NFRC) sticker on them, leaving us in the dark about their transmittance characteristics. Once I stood inside, in front of these windows on a sunny fall day, the lack of warmth coming through clued me in that the low-e coating was hobbling the passive solar gain of the small cabin. While the south-facing wall had almost 43 square feet of solar collection area for the interior space of 120 square feet (or roughly 35%; well above a 7% to 10% ratio of collection area to living area), most of the window area was barely adding to the heat gain. Given that the wall space occupied by the windows was of a substantially lesser R-value than the surrounding walls and thereby losing much more heat, the total contribution of the windows to heat gain was probably a wash. Passive solar heating wont work if window coatings are keeping the sun out. So be sure to check out the NFRC label carefully. Any window being installed for passive solar must meet the following criteria: Have a solar heat gain coefficient (SHGC) greater than 0.60 Have a U-factor of 0.35 or less Have a visible transmittance (VT) greater than 0.65 Be certified by the NFRC

The small office was wired for AC, then spray foam insulation was added to the beefed-up frame (2 by 4 walls; 2 by 6 roof rafters) to create a tight building envelope with a higher insulation value than conventional fiberglass insulation (about R-6 per inch). The floor received a few inches of spray foam and was also covered in reflective foil. Recycled doors and windows, purchased from a Habitat for Humanity reuse store, were installed. Unfortunately, the energy labels on these windows were missing, which led to incorrect assumptions about their passive solar capabilities (see Window Shopping sidebar). The interior was finished with locally milled pine bead-board, making the structure drywall-free. GDD also built an accessibility ramp and a loft for storage. They then protected the structure with a colorful paint job using zero-VOC paints purchased from the local building supply store.
Spray foam provides gap-free insulation for the old structure.

www.homepower.com

87

Courtesy The Abundance Foundation

off-grid office
Energy Retrofit: PV System
The group wanted to use solar electricity and as much supplemental solar heating as possible. They drafted board member and PV expert Rebekah Hren to help design and install the solar-electric system, and asked me to help with a solar air heater for space heating. Keeping to their educational mission, the staff turned the installation of both systems into workshops. One decision TAF faced was whether to tie the PV system to the grid or to go with an off-grid battery-based system. If the staff wanted to create an office of the future, then tying into the grid would make sense. Gridtied systems are less expensive, require less maintenance, and send any excess With a little attentive load management by the staff, 510 W of PV modules provide all the renewable electricity out to the grid. electrical energy for the little office. But grid-tied systems require access to the grid and extra paperwork that can make their implementation more On a weekend in November 2009, Rebekah and I ran onerous initially. Running the additional wiring from the simultaneous workshops to install the off-grid PV system and existing building to tie it to the grid proved too expensive for the solar air heater. With almost 30 people attending, it was a such a small space. Since there were few examples of off-grid little crowded around the small cabin, but we managed to get systems in the area, and learning about off-grid solar has everything done. more appeal to the DIY crowd that routinely signs up for TAF The PV system consists of three Evergreen ES-170 SL workshops, the staff decided on an off-grid system. modules totalling 510 W. The modules are wired in series, The office has only a few loads, so sizing the system was for a maximum output of 76 V. An OutBack MX60 charge straightforward. A few laptop computers, a ceiling fan, lights, controller steps this voltage down to 12 V for the MagnaSine printer, and a wireless router are the primary loads. Rebekah 2,000 W inverter/charger and the battery bank, which consists interviewed the office staff about what loads they needed of two 6 V Trojan L16E-AC batteries wired in series. Key was and expected to run (how many laptops, printer, router, making the system components as accessible as possible for etc.), and sized the system accordingly with a system sizing future workshops where the system will be disassembled and spreadsheet. reassembled. The battery box, inverter, and DC panel are all located in a small, weather-tight enclosure on the outside of the building. A TriMetric meter keeps track of the battery banks state A DC distribution panel, an OutBack 60 A charge controller, and of charge, and the office staff were all given instructions for a MagnaSine 2 kW inverter round out the power system. how to work in an off-grid environment. There is no backup generator, and if there are multiple days of cloudsand with little PV chargingthe office staff implements load management to keep the battery bank healthy. It has proven

System Loads
Load Lights Fans Computers Printer Wireless router Watts 25 100 80 200 15 Hours per Day 6 8 8 1 24 Days Avg. Daily per Week Watt-Hours 5 5 5 5 7 107 571 457 143 360 1,638

Average Total Daily Load

88

home power 145 october & november 2011

off-grid office

TAF Office PV System

Note: All numbers are rated, manufacturers specs, or nominal unless otherwise specified. DC Distribution Panel: OutBack PSDC Batteries: Two Trojan L16E-AC, flooded lead-acid, 6 VDC, wired for 370 Ah at 12 VDC
250
GFCI

Photovoltaics: Three Evergreen 170SL, 170 W at 24 VDC, wired for 510 W at 72 VDC

Combiner Box

60

60

60

Inverter: Magnum Energy MagnaSine MS2012, 2000 W sine wave, 12 VDC in, 120 VAC out

60

AC Distribution Panel: To 120 VAC loads

Charge Controller: OutBack MX-60, 60 A MPPT, 72 V in, 12 V out

G N H

Ground

Tech Specs
Overview
System type: Off-grid, battery-based PV System location: Pittsboro, NC Solar resource: 4.71 average daily peak sun-hours Production: 44 AC kWh per month

relatively easy to keep the system fully charged, since the office is closed at night and on the weekends, and loads are switched off then. One of the staff members has been instructed in how to safely water the flooded batteries on a regular schedule, and she checks them monthly and adds distilled water when necessary, taking the appropriate safety precautions.

Photovoltaics
Modules: 3 Evergreen ES-170 SL, 170 W STC, 25.3 Vmp, 6.72 Imp, 32.4 Voc, 7.55 Isc Array: One series string, 3 modules per series string, 510 W STC total, 75.9 Vmp, 6.72 Imp, 97.2 Voc, 7.55 Isc Array combiner box: A Ready Watt pass-through box transitions wiring from USE-2 input from PV modules to THWN2 output Array disconnect: OutBack 60 A OBDC breaker (plus 60 A ground-fault protection breaker) Array installation: Direct Power & Water Power-Fab rail installed on south-facing roof, 45 tilt

Two Trojan L16EAC batteries provide 370 Ah of energy storage.

Energy Storage
Batteries: 2 Trojan L16E-AC flooded lead-acid, 6 VDC nominal, 370 Ah at 20-hour rate Battery bank: 12 VDC nominal, 370 Ah total Battery/inverter disconnect: 250 A breaker

Balance of System
Charge controller: OutBack MX-60 A, MPPT, 76 VDC input, 12 V nominal output voltage Inverter: Magnum Energy MagnaSine MS2012 sine wave, 12 VDC nominal input; 120 VAC, 2,000 W output System performance metering: Bogart Engineering TriMetric meter & Magnum ME-RC50 remote control inverter meter A Bogart TriMetric battery monitor and the Magnum Energy remote display keep track of system performance.

www.homepower.com

89

off-grid office
Active Solar Heating Retrofit
The Piedmont area of North Carolina has a relatively mild climate overall, but winters get cold, with about 3,000 heating degree days on average. TAF hoped to provide for as much of their heating needs as possible using the sun. GDD had previously added two casement windows to the south side of the small building to capture some solar gain in winter, but there was room on the south-facing wall for additional solar gain, and TAF wanted to demonstrate both passive and active solar heating. Passive solar heating is accomplished by installing windows with appropriate solar heat gain values in a south-facing wall, with thermal mass (usually stone or concrete) to absorb and store the resulting solar gain. A roof overhang (or other shading) of the appropriate depth allows the winter sun in, but helps block unwanted sun in the summer. A well-designed passive solar home is attractive and functional, with significantly reduced need for mechanical space heating. Plus, it has the additional benefit of eliminating or reducing the need for artificial lighting during the day. The drawback is that, during the night, when temperatures plunge, heat can be lost through the glazing. Active solar air heaters are generally inexpensive, can be easily added to an existing buildings south-facing wall, and only operate when the sun is out (and hence dont lose heat at night or during cloudy weather). The drawbacks are that they can be less aesthetically appealing than a passive solar designed space, they do not have heat storage, and they dont contribute to daylighting. The first decision TAF had to make was whether to purchase a premanufactured solar air heater or to build one from scratch. DIY solar heaters can be made inexpensively, and can incorporate recycled or reused materials. Premanufactured solar air heaters are likely to be more durable, quicker to install, and may qualify for federal and state incentives that can make them as inexpensive as homemade ones. For many incentive programs, the collector must be rated by the Solar Rating and Certification Corporation (SRCC).

Above: The homemade 3- by 6-foot hot air collector augments space heating. Left: A 30 W PV module, mounted vertically for the low winter sun, directly powers the hot air collectors circulation fan.

The staff decided on a DIY heater so workshop participants could get hands-on experience with building oneand understand in detail how they function. Because access to the wiring inside the building was limited by the spray-foam insulation, we decided to power the heaters DC blower with

Left: A backdraft damper vents warm air into the office space from the top of the collector, but prevents reverse convection at night or during cloudy weather.

Right: The DC circulation fan draws cool room air into the bottom of the collector. Powered PV-direct, the air flow is proportional to the amount of sun.

90

home power 145 october & november 2011

off-grid office

TAF Off-Grid Office Costs

PV System
3 Evergreen PV modules SL 170 W Magnum MS2012 inverter, 12 V, 2 kW 2 Trojan L16E-AC batteries, 6 V, 370 Ah Rough wiring & labor PV mounts (combination of DP&W & UniRac) Shipping AC breakers & box, incl. labor OutBack PS2DC breaker box w/ GFP (used) OutBack MX60 charge controller (used) Ready Watt MC cable to wire Pass-Thru box Misc. boxes, breakers & cabling TriMetric TM-2020 battery monitor w/ shunt & cable Misc. conduit & hangers Inverter battery cables 4/0, 10 ft. Magnum ME-RC50 remote inverter control Battery interconnects Battery box misc. OutBack remote temp. sensor w/ cable Total PV System Cost Cost $1,797 1,320 540 350 330 260 250 250 225 180 173 171 168 150 140 138 75 24 $6,541

Fiberglass insulation forms the back layer of the collector, preventing unwanted heat transfer into the space during the summer, or outwards at night or during cloudy periods in the heating season.

a small PV module. A DC fan, powered by the module, pushes air from the interior of the room into the bottom of the heater. As the air flows through the heater, it warms and returns into the room from the top of the heater. A wall-mounted heater is ideal because having the inlet and outlet heights far apart promotes air circulation, which is more difficult to do with a roof-mounted unit. Baffles in the heater slow the air and create turbulence for better heat exchange between the collectors hot interior surfaces and the air. A backdraft damper at the top of the heater keeps air from flowing into the heater when there is not heat to be gained. The design assumption is that if there is enough sun on the PV module to run the fan, then there is enough heat in the box to make it worthwhile to move air. The PV module must be placed so that it has
A black aluminum sheet acts as the absorber plate, converting sunlight to heat. The collector will be covered with Lexan glazing.

Solar Air Heater (see the article on page 112)

Total Solar Air Heater Cost $610

Building
Purchase structure Labor Deck, ramp & rail materials Interior paneling Foundation, concrete block & labor Concrete sidewalk Spray-foam Insulation Exterior paint job Engineering for building Floor finishing Backhoe work Engineering for deck & ramp Breaker box, ground rods, other electrical Building permit Engineer-required framing Battery closet materials Exterior commercial door Rough-in wiring Total Building Cost Grand Total Project Cost $4,500 4,330 2,654 1,665 1,500 1,317 1,100 825 600 503 424 300 270 245 245 210 165 100 $20,953 $28,104

solar access at the same time as the air collector, so it is mounted on the same wall. The more sunlight that is on the PV module, the more power goes to the blower, so more air is moved through the heater. A switch can turn off the blower if heat is not needed. There are a myriad designs for a DIY solar air heater, and we chose a simple, 3- by 6-foot rectangular box. We sheathed one side of the 1-by-4 frame with 1/2-inch plywood. Inside the box, we put in some 1 by 2s for baffles and fiberglass
www.homepower.com

91

off-grid office
The Proof is in the Performance
A year and a half later, the little office has performed admirably. Powering all of the electronics with the PV system has not been a problem, and the solar air heater helps keep the building warm on sunny winter days, typically raising the interior temperature by 10 to 15F. On colder, cloudier days, a small auxiliary propane heater is needed. During our hot, humid summers, the building is excessively warm, so some kind of air conditioning, if not necessarily required, would make the space more comfortable (although this would probably overtax the existing PV system). Keeping the batteries full has not been a problem, but requires a bit of mindfulness on the part of the TAF crew, like using a power strip to shut off phantom loads at the end of the day; using laptops instead of desktop computers; and using efficient fans and compact fluorescent bulbs. While there are still kinks to work out, the workers at TAF are happy to occupy a small part of a renewable future.

Access
TAF staffCamille Armantrout, Tami Schwerin, and Jamie Kozlowskilove their energy-efficient and energy-independent office. Stephen Hren ([email protected]) is a builder, teacher, and author focusing on sustainable design. He is the author of the upcoming book Tales from the Sustainable Underground and coauthor of The Solar Buyers Guide for the Home and Office and The Carbon-Free Home. The Abundance Foundation www.theabundancefoundation.org

batt insulation. A matte-black, prepainted sheet of aluminum serves as the absorber plate, which sits on top of the baffles. A clear acrylic sheet serves as glazing.

How much will it cost to replace your solar controller in the middle of the desert?
Highest reliability Best warranty Failure rate less than 0.2%
Choose Morningstar with over 2 million controllers installed in over 50 countries for the past 18 years.

PHONE: +1.215.321.4457 www.morningstarcorp.com

c OmE

SEE uS exas , Dallas, T ct. 17-20 O 621

# BOOTH

92

home power 145 october & november 2011

YOU JUST WANT YOUR SOLAR ELECTRIC SYSTEM TO WORK AS HARD AS YOU DO

! Experience ! Expertise ! Excellence ! Locally Owned & Operated ! Licensed/Bonded in CA & OR

W E H AV E T H E E X P E R I E N C E A N D E X P E R T I S E T O M A K E T H AT H A P P E N
Electron Connection is a business dedicated to Renewable Electricity produced onsite. We have been in this business since 1988. We have produced our own electricity, both for domestic & business usage since 1970. We know what works and lasts by our own daily direct experience. We are committed to Renewable Energy. We design, sell and install Renewable Electricity (RE) power systems, grid inter-tied, off-grid, residential and commercial.

Electron Connection, Inc.

Providing Renewable Energy Solutions in The State of Jefferson since 1991 Serving Siskiyou, Jackson and Josephine Counties in Northernmost CA & Southern OR

CA Electrical License #613554 Oregon CCB#185672 Certified NABCEP PV Installer #102503-48 Oregon Renewable Energy Tech #LRT002 Energy Trust of Oregon Trade Ally #10035-09 Oregon Dept. Of Energy Certified Contractor

Bob-O Schultze POBox 203, Hornbrook, CA 96044 Tel 800-945-7587 Fax 530-475-3401

electronconnection.com

Understanding PV Module Specifications

by Rebekah Hren

Peak Power

Dimensions

Power Tolerance

Cell Type Peak Voltage Frame Peak Current

Glazing

Efficiency

Wiring Connectors

Temperature Performance

Load Rating

Warranty

Wind Rating

Certification

Courtesy SolarWorld USA

96

home power 145 october & november 2011

PV specs Specification sheets are readily available from manufacturers and distributors for the thousands of PV modules on the market today. Spec sheetsor cut sheetsserve as marketing material for the manufacturers, but also contain a large amount of technical information necessary for PV system designand for choosing which module serves an application best.
A module spec sheet needs to be thoroughly investigated to ensure compatibility before purchasing any PV system equipment. Once a module has been chosen, be sure to follow the complete manufacturers installation instructions, which are separate from the spec sheet. This article defines and explains the pertinent technical data listed on a spec sheet.

Typical Technical Diagrams

37.5 in. 20 in. 65.5 in. 1.5 in. Leads: 40 in. 39.0 in. 1.5 in. 0.75 in.

Technical diagrams identify module dimensions and other important details, like the location and size of mounting holes, grounding points, and lead wire length.

Simply width times length, the area of a module is useful for checking power density (watts per ft.2). The total module area can be used along with site-specific data to calculate wind uplift forces and thus lag bolt requirements, or to calculate weight loading on a structure.

Area

The Marketing

Thickness

Spec sheets usually start off with a few glossy pictures and advertising about the modules quality, efficiency, or a special design aspect. This is just marketing, surrounding the technical data the spec sheet delivers. Not every spec sheet follows the same layout, but at minimum, the sheets contain electrical and mechanical data.

The frame thickness determines what rack components to use, like slip-in racks, or the required size of end and intermodule clips. Typically, thicker frames result in sturdier, although heavier, modules.

Weight

Mechanical & General

Dimensions
Given in inches and/or millimeters, a modules size determines how many can fit in a given space, whether on a roof or on a ground- or pole-mount. If rack information is also known, the number of rows and each row length can be determined, based on the space intermodule clips add between modules (typically 1/2- to 1-inch per gap). Many manufacturers will also diagram the appropriate rail positioning for their modules, such as how much of the module can overhang the rails, and whether rails can cross the module in a landscape or portrait orientation or both. Be sure to follow the complete manufacturers instructions, as required by the National Electrical Code [110.3(B)].

Most permitting authorities will ask for basic structural engineering data for roof-mounted PV arrays, and there will be a limit to the weight that can be added to a roof structure. Module weight, rack weight, and engineering data will restrict the quantity of PV modules that can be installed. Crystalline, glazed modules with plastic backsheets typically weigh about 3 pounds per square foot. Many jurisdictions allow PV modules to be installed on pitched residential roofs without a professionally engineered design, as long as there is only one layer of existing roofing material present.

Cells

Cells will be either monocrystalline, polycrystalline, ribbon silicon, thin-film, or even multiple silicon layers, such as with Sanyos HIT module. Electrical characteristics, efficiencies, and appearance vary by cell type (see A Peek Inside PV, HP132). Modules can have variable numbers of cells (usually between 36 and 108), with each crystalline cell operating at around 0.5 VDC,

Thin-Film
Kris Sutton (3)

Monocrystalline
www.homepower.com

Polycrystalline 97

20 in.

What panels are you using? With SMA, it doesnt matter.

SMA is the leading manufacturer of solar inverters, featuring a product range compatible with any panel and power class, for grid-tied, off-grid and back-up applications. More people rely on SMA inverters than any other because of their superior reliability and unmatched performance. The choice is simple: For every panel, for every system, choose SMA. www.SMA-America.com

THE FUTURE OF SOLAR TECHNOLOGY

PV specs
Some crystalline modules have a glass backing (such as bifacial modules that can also utilize light reflected to the back side). Thin-film modules have a wider range of backings, including glass, stainless steel, and varieties of tough plastic polymers.

Encapsulation
Courtesy Florian Solar

A glue laminate, such as ethylene vinyl acetate, is used to seal and protect the back and front of cells within the module glazing and backsheet.

Frame

Some crystalline modules are frameless (Lumos Solar; Silicon Energy), with a glass front and back, similar to the technique used for many thin-film modules. But most crystalline modules have anodized aluminum frames, with clear-coated aluminum and black being the most commonly available colors. Noting the frame information can help with other decisions, for example making sure that the color of the frame matches rack and clips, and to help blend with the roof color.

The anodized clear-coated aluminum frames and white backsheets of traditional PV modules may provide slightly better performance due to lower heat absorption.
Topher Donahue

Sanyo, Lumos Solar, and Silicon Energy make modules with transparent backsheets, which allow light to pass through between the cells.

wired in series or series-parallel configurations. For example, a 72-cell module with all cells in series will operate at a voltage of about 36 volts. But a 72-cell module with two series strings of 36 cells paralleled will operate at about 18 V, perfect for charging a 12 V battery.

Cell Dimensions

While all crystalline PV cells operate near 0.5 volts per cell, the diameter of the cell (normally 5 or 6 inches) will partially determine the current output of the cell, with larger cells producing higher current.

More and more, modules are being released with dark anodized frames and dark backsheets, which create a contiguous surface that is aesthetically pleasing to some.

Glazing

Most crystalline modules use low-iron, high-transparency tempered glass with an antireflection surface treatment. Lowiron glass has high clarity, and tempered glass shatters into small fragments, instead of sharp shards, if broken. Modules are strenuously tested for weight loading and impact resistance, and the front glazing of a module is extremely durable. Thin-film modules may use a polymer film (plastic) as the front sheet, which is designed for arrays in high-impact environments.

Backsheet

Most crystalline modules have a plastic backing material that seals the cells against environmental infiltration. The most common material is Tedlar, a polyvinyl fluoride film. This backsheet is the fragile underbelly of the module, and care must be taken not to scratch it.

98

home power 145 october & november 2011

Kris Sutton (2)

PV specs

Silicon Energy (left) and Lumos Solar (right) frameless PV modules may shed snow better and have less dust buildup at the module edges. In both cases, proprietary racking methods add to clean wiring and array aesthetics.

Connectors

The module leads connector type is important. Often called quick-connects, many new products are on the market. The old standardMulti-Contact (MC) 4has been joined by Tyco, Radox, Amphenol, and others. The 2011 NEC mandates that these connectors be touch-safe and, for circuits greater than 30 volts, require a tool for opening. Most of these connectors are not cross-compatible, so mixing modules will require properly mating connectors, as well as for wire runs to combiner or pass-through boxes. Factory-installed module leads will be listed in the spec sheet with wire size, insulation type, and length of the leads (positive and negative leads are not always the same length). Wire diameter generally ranges from 14 AWG to 10 AWG; or they may be listed in square millimeters (mm2). For low-voltage systems, less power will be lost to voltage drop if using modules with heavier-gauge wire. Insulation type on the conductors may be a single listing, such as PV wire, or have multiple cross-listings, including USE-2, RHW2, XHHW-2, and/or PV wire. All factory-installed module lead insulation types are tested to be sunlight-resistant and flexible at low temperatures, and are heavily or even double-insulated for installation in extreme outdoor environments. However tough these single conductor leads may be, they still must be protected in a raceway when they leave the vicinity of the array. The MC4 connector has been joined by other viable alternatives, including ones by Tyco, Radox, and Amphenol.

Junction Box

A junction box is factory-installed on the back of modules for the connections. Many are sealed and inaccessible to the end user. If it is specified as field-serviceable, the junction box can be opened, and leads and bypass diodes can be installed or replaced. For arrays that are readily accessible (for example, a ground-mounted array), field-accessible and conduit-ready junction boxes can allow for fittings and protective raceways to be installed and meet NEC 690.31(A) code requirements for accessible arrays.

A fieldserviceable junction box may accommodate custom wiring decisions, the use of conduit, and replacement of failed bypass diodes.

A sealed J-box cant be opened, but may better withstand harsh outdoor elements. www.homepower.com

99

Kris Sutton (3)

Topher Donahue

Peak Power

ompany Inc. otovoltaics C Ph

the USA! Theyre Built in Ever Made & oltaic Modules The Best Photov
STC Peak power max power Voltage at ax power Current at m open circuit Voltage at ort circuit Current at sh NOCT
2, 25C, 1.5 AM 1,000 W/m 220 watts Pmax 29.8 volts Vmp 7.39 amps Imp 36.8 volts Voc 8 amps Isc
20 in.

Dimensions

Open-Circuit Voltage

ifications Electrical Spec

General Mechanical &

37.5 in.

65.5 in.

1.5 in.

Leads: 40 in.

Short-Circuit Current

800 W/m , 47 Pmax

2

2 C, 1.5 AM 159 watts 27 volts 5.9 amps 34 volts 6.47 amps

39.0 in.

1.5 in.

0.75 in.

20 in.

Weight

I-V Curve

Peak power max power Voltage at ax power Current at m open circuit Voltage at ort circuit Current at sh

Cells
65.5 x 39 in. 17.7 ft.
2

Vmp Imp Voc Isc

Dimensions Area Thickness Weight Cells ons Cell dimensi Glazing Backsheet n Encapsulatio Frame
40

1.5 in. 39.6 lbs. lline silicon 60 monocrysta 6 in. 6x , tempered ency, low-iron High-transpar t ection treatmen efl glass with antir ce polyester high-performan Double-layer, te Ethyl vinyl aceta Black anodize d aluminum nnector Wire, Tyco co 12 AWG, PV lok Tyco Solar 3 diodes allet; 20 modules/p iner llets/40 ft. conta 28 pa 75 lbs./ft. 120 mph
2

10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 0 5 10 Isc = 8 Imp = 7.39 Isc = 6.47 Imp = 5.9

STC NOCT
Peak Power = 159 W

Peak Power = 220 W

Frame

ps) Current (am

Connectors

Power Tolerance

15

20

Vmp = Vmp = 29.8 27 30 25

Voc = 34 35

Voc = 36.8

Voltage

Connectors

Module Efficiency & Cell Efficiency

l Parameters Other Electrica rcent

nce Power tolera Efficiency Temperature coefficients Pe Cell Module Pmax Voc Vmp Isc

x Junction bo es Bypass diod let; Modules/pal tainer Pallets/con Design load ind speed Maximum w

Junction Box

3% 15.5% 13.5% -0.45% per C -0.35% per C

Design Load

Temperature Coefficients
stem voltage Maximum sy ting ries fuse ra Maximum se

-0.42% per C +0.05% per C

600 volts 15 amp

Ratings Certifications &

Listing class Fire safety

UL 1703 C

Warranty
Warranty
power 90% rated ted power 80% ra ip Workmansh

Maximum Wind Speed

. lly existsorry company actua odule nor this r this PV m er Inc. Neithe of Home Pow inary subsidiary An imag

d 10 years limite ars limited 25 ye 5 years

Certifications & Qualifications

PV specs Bypass Diodes

Shading a small part of a PV module can have a disproportionally large effect on its output. Additionally, when a module is partially or completely shaded, the current flowing through the module can reverse direction and create hot spots, which can lead to deterioration of the cell, the internal connections, and the module backsheet. A bypass diode stops the reverse flow of current and also directs electrical flow around the shaded section of the module. Nearly all modules come with factory-installed bypass diodes, with the exception of some thin-film modules. A typical 72-cell module with all the cells in series will have three bypass diodes, each bridging a series of 24 cells that can be bypassed if any or all of those cells are shaded. Depending on where they are located on the module and the type of junction box, diodes may be field-accessible. Regardless of the benefit of diodes, shading should be avoided whenever possible.

Typical IV Curves
10 9 8 Isc = 8 Imp = 7.39

STC NOCT
Peak Power = 159 W

Peak Power = 220 W

Amperage

7 Isc = 6.47 6 Imp = 5.9 5 4 3 2 1 0 5 10

Vmp = 27 15 20 25

Vmp = 29.8 30

Voc = Voc = 34 36.8 35 40

Voltage

Modules per Pallet; Pallets per Container

A pallet of modules isnt a standard quantity. Details on packing information is important to help calculate point loading if pallets are to be placed on a roof, or for staging large job sites.

IV (current-voltage) curves at least show PV module performance characteristics for STC (Standard Test Conditions: 1,000 W/m2 irradiance, 25C cell temperature, and an air mass of 1.5). Often variations of typical conditions are graphed as well. All are important for system design.

Electrical Data
I-V Curve
Standard test conditions (STC) are the conditions under which a manufacturer tests modules: 1,000 W per m2 irradiance, 25C (77F) cell temperature, and 1.5 air mass index. Real-world operating cell temperature is often 20 to 40C above the ambient temperature. STC (bright sun and a relatively low cell temperature) are not typical for field operation of modules, but they do provide a consistent standardized reference to compare modules. An I-V curve (current-voltage) curve is generated at STC for every cell and module manufactured. The I-V curve contains five significant data points (Pmax, Vmp, Voc, Imp, and Isc; discussed below), which are used for system design, troubleshooting, and module comparisons. I-V curves can also be diagrammed for any operating temperature and irradiance level, but the points listed on a module specification sheet and those printed on the back of the module are at STC unless otherwise stated. Voc is used to calculate the maximum number of modules in a series string. Because voltage rises as the temperature drops, calculations are performed for the coldest expected operating conditions. This ensures that NEC parameters and equipment voltage limitations are not exceeded.

Imp

At STC, and tested under load, the maximum power current (Imp) is the highest amperage a module can produce. Imp is used in voltage drop calculations when determining wire gauge for PV circuits. This is a design consideration rather than an NEC ampacity calculation, for minimizing voltage drop and maximizing array output.

Peak Power (Pmax or Pmp)

Isc

The specified maximum wattage of a module, the maximum power point (Pmax), sits at the knee of the I-V curve, and represents the product of the maximum power voltage (Vmp) and the maximum power current (Imp). This wattage is produced only under a very specific set of operating conditions, and real environmental conditions (changing irradiance and cell temperature) will alter a modules Pmax.

Short-circuit current (Isc) is the maximum amperage that the module can produce. There is no voltage when a module is shortcircuited, and thus no power. Isc is the measurement used to size conductors and overcurrent protection, with safety factors as required by the NEC.

NOCT

Vmp

At STC and tested under load, voltage at max power (Vmp) is the highest operating voltage a module will produce. Vmp, adjusted for highest operating cell temperature, is used to calculate the minimum number of modules in series.

Voc

Open-circuit voltage (Voc) occurs when the module is not connected to a load. No current can flow in an open circuit and, as a result, Voc occurs at the point on the I-V curve where current is zero, and voltage is at its highest (Note: the module produces no power under open-circuit conditions.)

Frequently, nominal operating cell temperature (NOCT) specifications are also listed on a manufacturers sheet. These are measurements calculated at different conditions than STC, using a lower sunlight intensity (800 W per m2); an ambient (not cell) temperature of 20C; and a wind speed of 1 meter per second; with the module tilted at 45. The NOCT value itself is the cell temperaturegiven in degrees Celsiusreached under these conditions, Compared to the STC 25C cell temperature, the NOCT value will always be higher, usually by about 20C. NOCT values are used to mathematically calculate other test condition data points without resorting to further laboratory tests. NOCT conditions tend to more closely resemble the field conditions PV arrays generally operate in, and so give a perspective on realworld module operation.

100

home power 145 october & november 2011

PV specs

Other Electrical Parameters

Power Tolerance
Power tolerance is the range within which a module manufacturer is stating the module can deviate from its STC-rated Pmax, and thus what the manufacturer warranty covers. Common values are +/5%, -0%/+5, and up to +/-10%. A 200-watt module with a +/-5% power tolerance could produce a measured output of 190 to 210 W. Finding modules with a -0% power tolerance can ensure the best value per dollar spent, and keep arrays operating at closer to predicted output.

Efficiency is the measure of electrical power output divided by solar input. At STC, power in is equal to 1,000 W per m2 and power out is the rated Pmax point. Assuming a module sized at exactly 1 square meter, and rated at 150 W Pmax, module efficiency would be 150 W per m2 1,000 W per m2, which equals 15%. The typical crystalline efficiency range spans 12% to 15%, but there are high-efficiency modules over 19%, and amorphous silicon modules on the low end with efficiencies around 6% or 7%. Cell efficiencies will be slightly higher than module efficiencies because there is usually a small amount of empty space between cells. When deciding what module to purchase, if W per square meter (known as power density) is the driving factor, then a module with high efficiency should be chosen. But in many instances, there is plenty of room for an array and price per watt will be given higher priority than module efficiency.
Kris Sutton

Module Efficiency & Cell Efficiency

Temperature extremes affect PV performance, and thus temperature coefficients are instrumental in system design.

Temperature Coefficients

Modules are directly affected by both irradiance and temperature, and because of environmental fluctuations, also experience power output fluctuations. When exposed to full sun, the cells will reach temperatures above the STC temperature of 25C. And sometimes cell temperatures are lower than 25C, such as on cold winter days. Temperature coefficients are used to mathematically determine the power, current, or voltage a module will produce at various temperatures deviating from the STC values. The temperature coefficient of open-circuit voltage is used to figure out the PV arrays maximum system voltage at a sites lowest expected temperatures. The temperature coefficient of power can be used along with pyranometer-measured irradiance to calculate the power an array should be producing, which can be compared to actual output to verify proper performance.

Maximum Series Fuse Rating

This is the maximum current a module is designed to carry through the cells and conductors without damage. While modules themselves are current-limited, excess current can come from other sources (series strings) in parallel, or from other equipment in the system such as some inverters or charge controllers. A fuse or breaker for a series string must be no larger than the maximum series fuse specification.

The weight (in lbs. per ft.2, PSF) that a module has been tested to hold without damage. Modules will usually handle 50 PSF. In areas with heavy snow loads, modules with a higher design load should be used and may be required by the permitting authority.

Design Load

Maximum Ratings
Maximum System Voltage
For residential PV systems, the maximum allowed voltage is 600 volts (per NEC 690.7(C)), but ratings on equipment are just as critical to abide by. While most of the equipmentincluding modulesin PV systems is rated for up to 600 V, they are generally tested to higher voltages, usually twice the listed maximum plus 1,000 V. Maximum system voltage is calculated using the Voc at coldest expected temperatures (see Back Page Basics in HP128) so as not to exceed the NEC limit and any limits imposed by the ratings of inverters, disconnects, or conductors. Modules sometimes list a 1,000 V limit, but that is for European installations or engineered commercial and utility-scale systems.

Maximum Wind Speed

This is the maximum wind speed a module can handle without damage, and 120 mph is a common rating. Your local building authority can provide the design wind speed you need to use. In areas with higher-than-normal wind speeds, thin-film or frameless, glass-onglass modules may be the only choice with a high-enough rating.

Certifications & Qualifications

For a code-compliant installation, modules need to be tested to UL standard 1703, and stamped by a nationally recognized testing laboratory (NRTLs, as listed by OSHA) as meeting this standard. Other NRTLs include CSA, TUV, and Intertek (ETL). Modules often list other compliances and qualifications, including International Standard for Organization (ISO) 9001:2008 which is an international standard for a quality management system.

www.homepower.com

101

PV specs Fire Safety Class

Plastic-backed modules with glass fronts are nearly always listed as Fire Safety Class C, which means they are potentially energized electrical equipment, and no conductive agents (such as water) should be used to fight the fire.

Warranty

Modules list separate workmanship and power warranties. The workmanship warranty is a limited warranty on module materials and quality under normal application, installation, use, and service conditions. Certain parts of modules, including quick connects and some junction boxes, have only short warranties from their manufacturer, and this is reflected in overall workmanship warranties of one to 15 years. Manufacturers may offer replacement or servicing of a defective module under the workmanship warranty. A limited warranty for module power output based on the minimum peak power rating (STC rating minus power tolerance percentage) means that the manufacturer guarantees the module will provide at least a certain level of power for the specified period of time. Many warranties are steppedcovering a percentage of minimum peak power output within two different time frames. For example, a common warranty guarantees that the module will produce 90% of its rated power for the first 10 years and 80% for the next 10 years. A 200 W module with a power tolerance of +/-5% means that the module should produce at least 171 W (200 W 0.95 power tolerance 0.9) under STC for the first 10 years. For the next 10 years, the module should produce at least 152 W (100 W 0.95 power tolerance 0.8). Module replacements are frequently done at a prorated value according to how long the module has been in the field. More manufacturers are now offering linear power warranties, which are represented by a maximum percentage power decrease

Richard Perez

PV modules are durable goods, and have the potential to last a very long time, as these old still-operating modules prove. Protect your investment by choosing a brand with a good warranty. per year for a set number of years, for example, that module power output shall not decrease by more than approximately 0.7% per year after the initial year of service, for the first 25 years.

Access
Rebekah Hren ([email protected]) is a licensed electrical contractor, NABCEP-certified PV installer, and ISPQ-certified PV instructor for Solar Energy International. She lives off-grid and has experience installing and designing PV systems ranging from 10 watts to utility-scale. Rebekah has coauthored two renewable energy books: A Solar Buyers Guide and The Carbon-Free Home.

102

home power 145 october & november 2011

www.homepower.com

103

PV-Direct Water Pumping

by Dan Fink

Untethered to the grid or to batteries, PV modules can still do useful work around your home, farm, or ranch.
104
home power 145 october & november 2011

Like wind-powered pumping systems, modern PV-direct pumping systems turn the available renewable resource into pumping power in a few steps.
Courtesy SunPumps

PV direct
systems that power loads directly from a PV module or array are called PV-direct, and operate only when the sun is shining. These systems are much less expensive and easier to install than battery-based or grid-tied designs. They do not require batteries, charge controllers, or inverters, all of which are expensive and reduce overall system efficiency. The most common PV-direct application is solar water pumping for irrigation, livestock, and domestic use. If water is what you need, why bother with batteries? Water tanks are far cheaper than battery banks, and last for decades. These systems work well as long as you can store enough water to get you, your plants, and your animals through periods of no sun. PV-direct pumping is not used to provide domestic water pressure, but usually to fill a tank. Gravity or a separate, inexpensive water pressure-pump system is instead used to push stored water to your household faucets, shower, etc. Water pumps for PV-direct use come in a several varieties: Surface pumps are used to move water from sources like shallow wells, ponds, streams, and tanks, where the pump itself is located no more than 20 feet above the water level. There are many types available; your choice will depend on how much water per day you need to move, how high, and how far. Submersible pumps are for deeper wells, where the pump cant be installed within 20 feet above the water level. These pumps are suspended below the water level in the well and connected to an output pipe that extends up to the surface. Once again, the right pump for your application depends on your needs for quantity of water and pumping height and distance. Circulation pumps are used to move water around in a closed system, such as solar water heating for domestic water, space heating, pool, or spa. They generally lift water only a short height. Why is there a 20-foot height limit from a waters surface to pump? Pumps can push water up hundreds of feet and move it horizontally over great distances, but must rely solely on atmospheric pressure to suck water up to their level for pumping to the final destination. The theoretical limit is 33.9
This SunPumps submersible pump is designed to be suspended deep in a well, and can be powered directly by a PV array.

Courtesy SunPumps (2)

A DC surface pump (below) is often built for higher flows, but usually cannot draw water more than 20 vertical feet, making it highly suitable for moving water from surface sources like the irrigation pond (at right).

Courtesy Innovative Solar

www.homepower.com

105

PV direct

Linear Current Boosters

Electric pump motors require extra power to start spinning up to four times the power used to just run. Many pump controllers have linear current booster (LCB) circuitry, trading volts for amps (and vice versa) to run the pump at its most efficient rate for the amount of power the PV array is producing. On an overcast day, a pump with no LCB may be sitting idle, while a pump with an LCB can overcome the required startup load and then run all day, albeit at a slower rate, proportional to solar intensity.

PV-direct systems turn the suns rays directly into useful work, but a pump controller is used to turn the pump on and off, and can optimize the systems performance.

feet (10.3 meters) at sea level, but even the slightest vacuum leak will drastically reduce that limit, as will high altitudes. As little height as possible, with a maximum of 20 feet (at sea level), is a realistic guideline.

through both nighttime and periods of cloudy weather when the pump wont be running (or is running slowly). Next, youll need to calculate your systems total dynamic head (TDH). This is the sum of the static head (total vertical distance from water surface to discharge outlet), friction head (friction losses from pipe walls and bends in the pipe), and pressure head (losses from any nozzles or filters in the lines). Head can be expressed in either feet of water or pounds of pressure per square inch. Head (in ft.) 2.31 = psi Head (in psi) 2.31 = Head (in ft.) Static head needs to be measured to an accuracy of 1 foot, which can be done using a level and rod. Topographic maps or GPS measurements are not accurate enough. A sight level with a measuring rod or some other means is necessary. (For more info on measuring head, see Intro to Hydropower in HP104). If you have a deep well, the driller should have provided you with the distance from ground level down to water level. If not, they can come back to measure it (they use a special sensor) or you can come up with your own measurement solution. Well draw-downhow far the water surface level drops while you are pumping wateralso affects static head measurements. Your well driller should have also provided you with this information right after the well was drilled and the pump installed, and also the rate (in gallons per minute; gpm) at which the well refills.

Pump Controllers
In the simplest PV-direct application, a controller may not be requiredwhen the sun shines, the pump runs, and when the sun sets, the pump stops. But in most systems, a controller is wired between the PV array and the pump to stop water flow when the tank is full and to prevent running the level of the water source so low as to run the pump dry. To sense water level, float switches are wired to the controller and they use gravity to open or close contacts as the float angle changes with water level. Most are intended to switch the entire current of a typical 120- or 240-volt AC pump, and may not function properly with the low-voltage, low-amperage sensing circuit in the solar pump controller. Be sure to get the right switch for your application. For irrigation, there are other switches available, such as soilmoisture sensors to prevent over-watering, and high-wind sensors to shut the system down when winds might spread water to where its not wanted.

System Sizing
The easiest way to determine the size and cost of a PV-direct water-pumping system is to ask your favorite renewable energy dealer! They will have spreadsheets and product specifications handy, and be able to do the math quickly for you. It never hurts to do your homework, though, so you have a rough idea of how much youll have to invest. In any case, youll need some critical information to get an accurate cost estimate. First, youll need to know how much water you need to move per day, and size your storage tank to get you

PV-direct pumping systems can provide domestic water at remote sites, utilizing only a small PV array.

Courtesy SunPumps (2)

106

home power 145 october & november 2011

PV direct
Dedicated PV Array: Sized to match pump and required TDH & flow (may be high voltage) Float Switch: Prevents tank overflow Pipe Run: Length and friction loss effects TDH

Difference in Elevation: From well head to top of tank

Pump Controller: With linear current booster (LCB), which optimises V & A for pump Total Dynamic Head (TDH): Total static head, plus friction loss from pipes, fittings, filters, etc. Well Casing

Filtration: Removes sediment; affects TDH

Tank or Cistern: Holds enough water to get through periods of little sun

Well Depth: To draw-down level; affects total pipe length & head

Submersible Pump: DC-powered, low-voltage

Basic Components of a PV-Direct Water Pumping System

Horizontal distance from pump to discharge outlet can be measured with a tape, but friction head calculations involve complicated math that includes flow rate; pipe diameter, length, and smoothness; and any fittings in the line. Fortunately, friction head can be estimated using tables provided by pipe manufacturers. There are also numerous friction-loss calculators available online. If you are pumping from a well, be sure to include the pipe length from the pump to ground level in your total distance. Because typical, home-sized PV-direct systems pump slowly, you can safely assume a pipe diameter of 3/4 to 1 inch, and adjust this later as you narrow down which pump you need. Using very large diameter pipe (greater than 2 inches) is not recommended in small systemsits expensive, and with low flow you may have sediment buildup inside the pipe. For pressure head, the manufacturer of the irrigation nozzle or water filter you are planning to use will provide you with pressure drop data, in pounds per square inch (psi). Lastly, youll need to find out the average number of full-sun hours your site receives each day. You can look up your location on an insolation map online (http://rredc.nrel. gov/solar/pubs/redbook), or use PVWatts, NRELs online calculator. With this information, you can get a quote from a solar pump dealer.

Example Pipe Friction Loss

Flow (GPM) 1 2 3 4 5 6 7 8 9 10 11 12 14 16 18 20 22 24 26 28 30 35 40 45 50 55 Polyethylene (PE): PSI per 100 ft.
1/2

in.

3/4

in.

1 in. 0.04 0.14 0.29 0.50 0.76 1.06 1.41 1.80 2.24 2.73 3.25 3.82 5.08 6.51 8.10 9.84 11.74 13.79 16.00 18.35 20.85 27.74 35.53 44.19 53.71

1 1/4 in. 1 1/2 in. 0.01 0.04 0.08 0.13 0.20 0.28 0.37 0.47 0.59 0.72 0.86 1.01 1.34 1.71 2.13 2.59 3.09 3.63 4.21 4.83 5.49 7.31 9.36 11.64 14.14 16.87 0.00 0.02 0.04 0.06 0.09 0.13 0.18 0.22 0.28 0.34 0.40 0.48 0.63 0.81 1.01 1.22 1.46 1.72 1.99 2.28 2.59 3.45 4.42 5.50 6.68 7.97

2 in. 0.00 0.01 0.01 0.02 0.03 0.04 0.05 0.07 0.08 0.10 0.12 0.14 0.19 0.24 0.30 0.36 0.43 0.51 0.59 0.68 0.77 1.02 1.31 1.63 1.98 2.36

0.49 1.76 3.73 6.35 9.60 13.46 17.91 22.93 28.52 34.67 41.36 48.60 64.65 82.79 102.97

0.12 0.45 0.95 1.62 2.44 3.43 4.56 5.84 7.26 8.82 10.53 12.37 16.46 21.07 26.21 31.86 38.01 44.65 41.79 59.41 67.50

Selecting a Pump
The common design philosophy behind PV-direct water pumping is simple: Pump slowly with as few PV modules as possible, and install a big storage tank. PV-direct pumps in home-scale systems generally operate in the range of 1 to 4 gpm, while typical AC well pumps usually work at 6 gpm and up. These pumps are not suitable for PV-direct usethey require a battery bank, an inverter with high surge capacity,

Source (includes tables for other pipe types): www.hunterindustries.com/Resources/PDFs/Technical/Domestic/LIT091w.pdf

www.homepower.com

107

PV direct

Other PV-Direct Applications

Water pumping is certainly the most common PV-direct application, but there are others that are also a perfect fit. Water aeration is used to oxygenate or prevent freezing in ponds. Some systems use water pumps and fountains; others use compressed air. A simple air compressor on shore and diffuser system at the bottom of the pond, powered directly by a PV module, can be very effective at keeping the water from freezing. Rising air bubbles bring warmer water from the bottom up to the surface, and aquatic life in eutrophic ponds with insufficient dissolved oxygen levels can also benefit from aeration. Sizing a PV-direct compressor/aeration system is very similar to sizing a water-pumping system. Instead of total dynamic head, youll be calculating air pressure drop (from pump depth and air tubing size), and the flow per minute will be measured in cubic feet instead of gallons. Instead of a pump curve, youll consult a compressor curve. But all the basic system design concepts remain the same, and purpose-built, efficient DC compressors are readily available. Water fountain aeration systems are sized using the same math as in other water-pumping applications.

Example Pump Specifications

5.0 4.5 4.0 SDS-Q-135 SDS-Q-130 SDS-Q-128

Flow (gpm)

3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 20 40 60

SDS-D-128 SDS-D-228

80 100 120 140 160 180 200 220 240 260

Total Dynamic Head (ft.)

PV-direct water or air pumps can provide aeration and/or freeze protection. PV-direct ventilation systems, such as greenhouse fans and attic fans, are also popular, and can be a very logical and costeffective applicationthe more intense the sunlight, the more airflow is typically needed in an attic, greenhouse, or other structure. Systems retain the same similarities in designthe blower, controller, and PV array must all be matched to the duct size and pressure losses. Efficient, purpose-built PV-direct DC blowers are easy to find.

The stronger the sun shines, the more air this PV-direct ventilation fan exhausts.

and a larger PV array. If you already have one of these pumps in your well, youll need to replace it to use PV-direct pumping. Most solar pump manufacturers provide graphs of specifications for their pumps, grouping model series on one graph to make selection easier. For example, lets say you need about 240 gallons of water per day for domestic, livestock, and irrigation use. From well draw-down level to the cistern, the water must be lifted 60 feet over a distance of 500 feet. You have 3/4-inch polyethylene pipe ready, and a sediment filter at the tank causes a pressure drop of 2.41 psi. The well refills at 3 gallons per minute. Your average daily insolation during the worst month of the year is 4 sun-hours, and you need enough water to ensure cloudy periods of up to 7 days. Working backward with storage capacity, youll need a 1,680-gallon water storage tank (240 gal./day 7 days). The flow rate required would be about 1 gallon per minute [240 gal./day 240 min./sun-hours day (the number of minutes in 4 hours)]. Because the well refills at 3 gpm, there is no chance youll run the pump dry. Next, calculate total dynamic head (TDH). The total pipe length is 560 feet (500 ft. horizontal + 60 ft. vertical). The 2.41 psi pressure drop from the filter adds 1 foot of TDH, and pipe friction at 1 gpm adds another 1.55 feet, for a total of 62.55 feet of TDH. There are also unknown factors, such as the friction from pipe connectors and valves. A safe estimate is 70 feet of TDHalways oversize your system. The lines on a pump manufacturers graph (above) show the maximum output the pump can produce at a given head and flow. Find the intersection of 1 gpm flow and 70 feet of head on the graph. That spot sits nicely below the curve of the example SDS D-series pumps, and far below the more expensive SDS-Q series. In this example, then, the D-series would be a better investment.

108

Courtesy SunPumps (2)

home power 145 october & november 2011

PV direct

PV / Pump Voltage Selection

1.6 1.4 1.2

1.0 0.8 0.6

30 VDC

25 VDC

15 VDC 0.4 0.2 0.0 0 25 50 75 100 125 150 225 200 275 250 12.5 VDC

Total Dynamic Head (ft.)

Sizing the PV Array

The final piece of the puzzle is calculating the size of the PV array required to run the pump at the specified head and flow rate. Again, the pump manufacturer can provide the specs for you. Most home-scale PV-direct applications require between 100 and 800 watts of PV, depending upon the site and the needs. You should always oversize the PV array by at least 20% to make up for electrical and mechanical losses in the system. If your calculations indicate a PV system larger than you can put in, you might save money with a smaller array and a pump with slower flowbut spending a little more on a larger water tank. In the example given, use the pump manufacturers voltage and capacity chart (above) to size the PV array. In this example, 1 gpm at 70 feet TDH is too much to run PV-direct from a single 17-volt PV modulethe spot where gpm and TDH cross is above the graph line. At 34 V module-direct, though, capacity is more than ample; the manufacturer calls for 72 W of PV. Two 50 W, 17 V modules in series would be ideal. For some systems, using a tracker so the PV array follows the sun to increase the energy output may be worth considering, though it will add expense and more moving parts to the system. If most of your water-pumping needs occur during summer when trackers yield the most benefit, you can calculate how cost-effective tracking would be by using NRELs online insolation calculator and examine scenarios using single- or dual-axis trackers. Even without using a tracker, consider using a mount that can be adjusted seasonally.

and cost are decreasedarray voltages of more than 150 volts are possible, combiner boxes may not be needed, and pump motors operate more efficiently at higher voltages. The LCB steps this down to something lower (usually 12 to 48 volts) near the pump. A high-voltage PV array is less costly to locate farther from the controller to give more choices for siting, and can be connected with smaller-gauge, less-expensive wire. PV-direct systems can often be installed without a structure to house the equipment. Be sure that all electrical equipment is installed and wired with weatherproof, outdoor-rated boxes and connectors. Follow the manufacturers recommendations for overcurrent protection for the pump and controller. PVdirect systems should be grounded to National Electrical Code specifications. That may entail two ground rodsone for the PV array frames, rack, and pole; one for the pump, controller, and electrical boxesdepending on distance and other factors. Grounding is a complicated issue, so be sure to consult with a system designer, electrician, or local electrical inspector. Like any renewable energy investment, PV-direct systems require research and design before the first PV module and pump is purchased and installed. Because each component must be carefully matched to the others and to the load, proper planning is essentialso the results will be an efficient, reliable system that will be functioning for years to come.

Flow (gpm)

Access
Author and educator Dan Fink ([email protected]) has lived 11 miles off the grid in the northern Colorado mountains since 1991. He teaches about off-grid systems and small wind power, and is the executive director of Buckville Energy Consulting, a NABCEP/IREC/ ISPQ-accredited continuing education provider. Dan is the coauthor of Homebrew Wind Power. Pump Manufacturers: ACS-Solarsystems www.acs-solarsystems.com/Solar_Pumps.htm Aquatec www.aquatec.com Hartell www.hartell.com Innovative Solar (Dankoff Solar Pumps) innovativesolar.com Ivan Labs Inc. (El-Sid) 561-747-5354 Laing http://lainginc.itt.com Lorentz www.lorentz.de/ LVM www.ittflowcontrol.com/alternative-energy/ March Pumps www.marchpump.com SHURflo www.shurflo.com Solar Converters Inc. www.solarconverters.com SunPumps Inc. www.sunpumps.com Solar Ventilation Fans: Natural Light www.solaratticfan.com Snap Fan www.snap-fan.com SunRise Solar www.sunrisesolar.net Pump Controls/Linear Current Boosters: AeroVironment www.avinc.com BZ Products www.bzproducts.net SunPumps Inc. www.sunpumps.com

Electrical Considerations
Depending on the pump and controller/LCB that you choose, different PV array wiring configurations may be possible. Its always better to use higher voltage at the array, as wire size

www.homepower.com

109

www.marcasmasvivas.com

Today Still evolving with you.

1970

1978

1982

1984

1988

1993

1997

2000

2008

Today

Join the Bornay experience.

From 1970 we've been pioneers in making use of wind energy. In taking light to isolated places. Four decades is a long time. We began in Europe, but we've applied our technology in 50 countries: the United States, Japan, Angola, the Antarctic... We've developed the most reliable low-power windturbines in terms of performance and robustness. Over 4000 installations across the world have chosen a Bornay.
Bornay Windturbines 600W 1500W 3000W 6000W

Now is the time to contribute to distributed generation by using windturbines specically designed for grid connection to work for you. Now, we're looking to embark on a long journey in the United States, sharing experience, knowledge and technology. We want to work with you, guaranteeing you quality installations and ensuring safety for your customers. When you think mini wind turbines, put your trust in Bornay.

For joined-up energy, join the Bornay experience.

bornay.com

In Movement Since 1970.

The TriMetric

Basic Battery System Monitors

Display vital battery system data to help users provide better battery care, conservation awareness and aid system maintenance: Volts Amps Amp-hours Battery% full Days since charged

The PentaMetric
Battery System Monitor with More Capability
The choice for advanced system analysis and maintenance.

Data Logging - records 3 weeks of system details System Troubleshooting by comparing to previous data.

Computer / Internet Interface

Traditional TM-2020

(without optional enclosure) $169

TM-2025-RV features:
12-48V operation standard. Higher lightning resistance. Smaller package includes enclosure. Also Watts. Records system analysis information to help nd system problems. $180

The P-100-CE with Ethernet connection. Now analyze renewable energy system performance via remote internet connection.

The PentaMetric System with (non internet) RS232 computer interface $320 Optional LCD Display unit (shown above) additional $199

TM-2025-RV

TriMetric

details at: www.bogartengineering.com

BOGART ENGINEERING (831) 338-0616 19020 Two Bar Rd. Boulder Creek, CA 95006 USA

110

home power 145 august & september 2011

NICKEL-IRON BATTERIES CLEAN ENERGY STORAGE FOR A NEW GENERATION

Iron Edisonis redening energy storage using advanced Nickel-iron
(Ni-Fe) battery technology. The Iron Edison battery system was originally designed by Thomas Edison, and is free of anyhazardousmaterials like lead or sulfuric acid. Vastly outlasting the 7 year service-life of their lead-acid counterparts, the Ni-Fe battery is quickly becoming the environmentally sensitive choice for both o-grid and grid-tie energy storage applications.
learn more and congure your system at:

IRON EDISON vs LEAD-ACID

IRONEDISON.COM

www.homepower.com

111

DIY
SOLAR AIR HEATER
by Stephen Hren
Stephen Hren

A build-it-yourself solar air heater can be a fairly simple project for motivated homeowners. These units can help offset or even eliminate the need for auxiliary heating, depending on the climate and the size of the space.

hen most folks hear about solar power, the first thing that comes to mind is solar electricity. Solar electricity is amazing stuff, but for households on a budget or for individuals who love to tinker in the shop, it is not the most accessible or affordable solar technology. Besides needing electricity, most homes, shops, or offices also need to be heated. Capturing solar energy for space heating is a straightforward and efficient way of bringing renewable energy into our lives. One of the most direct, easiest, and economical ways of doing this is with a solar air heater, used for supplemental heating. More than any other solar technology, solar heaters are DIY-friendly, since they require only a basic knowledge of carpentry and electrical skills, can be made of easyto-find materials, and can be installed on a south-facing wall rather than on a potentially dangerous roof. Solar air heaters are tolerant of less-than-exact construction details. A small air leak will only reduce the heaters overall efficiency, not leak fluid or potentially overheat or shock

you if installed improperly. While care should be taken with any project, the consequences of potential mistakes are much less dire. For homeowners interested in the basics of renewable energy, building a solar air heater can be a great project.

Considerations
Before beginning, its important to have access to the sun where and when you need itor all of your hard work will be for naught. Make sure there is full sunlight on the southfacing wall in the winter months from about 10 a.m. to 2 p.m. The sun is at a low angle during the winter, so the number of potential obstructions increases. If you cant accurately assess the winter solar window within a few weeks of the winter solstice, use a solar analysis instrument such as a Solar Pathfinder or Solmetrics SunEye. DIY solar heaters should be installed on south-facing walls and never on roofs. Homemade heaters tend to fare poorly in the extreme weather conditions that exist on roofs, and the produced heat tends to stay at the ceiling level. Hot

112

home power 145 october & november 2011

DIY heater
air is likely to stratify into layers and stay stuck away from where residents want itnear the floor. Using a stronger blower might seem like it would solve this problem and help circulate the air, but it risks moving the air through the heater too quickly before it has time to heat up, and quickly moving air, regardless of temperature, has the effect of cooling the skin and making a room feel drafty.

Solar Air Heater Anatomy

3 ft. x 6 ft. with weather stripping
3/16 in. Lexan

Glazing:

Baffles: Two, 1 x 2 in.; mix air

Damper: Prevents reverse convection when collector is cool.

Design Types
A solar air heater is basically a glazed, insulated black box with two vents. This simplicity allows a great variety of potential designs. Primary concerns are the designs efficiency, construction ease, and costand theres some trade-off between these goals. I decided on a simple design that blows air between a black metal absorber plate and polycarbonate glazing. A fan moves the air from the bottom of the collector to the top, transferring heat from the absorber to the air. Because this design uses a fan, it is an active solar air heaterthere are moving parts that require electricity. A passive solar air heater moves air by convection onlyas the air inside a passive heater warms, it expands and becomes lighter, moving upward until an unassisted flow called a thermosiphon develops. Active heaters are roughly 200% more efficient than passive heaters, but with additional complexity and cost. Passive heaters tend to become overheated and reradiate much of the heat trapped in the collector back to the outside before it warms the air flowing through into the building. Besides the difference between active and passive, there are four heater design considerations based on time, skill level, and available materials. The one we built is an empty box collectorair is heated by passing through an empty glazed box facing the sun. An improvement on the empty box collector design is the screen collector, which uses either a dark metal screen, lathe, soffit vent, or some other metal material with lots of holes, placed between the metal absorber plate and the glazing to cause air disruption. Creating turbulence in the air inside the heater allows more air to come in contact with the absorber plate to increase heat transfer. One problem with empty box and screen collectors is that dust and dirt accumulating in the heater and on the interior of the glazing can reduce efficiency. Other designs can eliminate the problem by isolating the air from the glazing. A can collector consists of aluminum cans (painted black) with their tops and bottoms removed. Stacked end-to-end, they form channels within the collector through which air passes. Other metal tubing, such as gutter downspouts, can also be used. The dead air between the glazing and the metal channels creates a layer of insulation, reducing heat loss through the glazing and raising the collectors overall efficiency. A backpass collector uses the same principle as the can collector, but instead of air traveling through channels, it travels behind the black metal absorber plate. This is common with pre-manufactured solar air heaters. For information on a variety of solar heater designs, see Gary Reysas website, www. builditsolar.com.

Insulation: 1 3/4 in. fiberglass behind absorber

Crosspieces: 1 x 2 in. lumber Backsheet:

1/2 in. plywood

Frame: 1 x 4 lumber

Air Path: Zigzags up through 1.5 in. gap

Absorber Plate: 0.04 in. aluminum, painted matte black

Fan: Draws air from room into collector through 4 in. duct

Making the Heater Active

Using an electric fan adds complexity to the collector design, but, in addition to increasing efficiency, allows the possibility of automation. Automating the fan with a thermostat (essentially a programmable switch) and temperature sensors (called thermistors) make the heater come on only when there is useful heat to be gained. But a simpler method would be to switch on the fan manually. I was interested in maximizing understanding of renewable energy, while at the same time keeping the design most useful and the construction as easy as possible. It made sense to use a small PV module to directly power a DC fan. A PV module placed where it gets the same solar exposure as the heater adds operational elegance: The fan only works when the sun shines on the collector and PV module, and the stronger the sun is, the faster the fan blows air through the heater. A manual DC switch allows users to turn off the heater when its not needed.

www.homepower.com

113

DIY heater

CONSTRUCTION
The box is constructed using 1/2-inch plywood, and 1 by 4s are attached to the perimeter using wood glue and exterior-grade screws. Weight is a concern, especially for full-sized 4- by 8-foot heaters. This heater is only 3 by 6 feet. Most of the materials came in dimensions that would have worked for a 4-by-8 heater, so the expense for the larger heater would not be much more. Airtight construction is important; wood glue helps greatly. Before insulating, the perimeter is lined with 1 by 2s to support the sheet metal. Across the back, 1-by-2 crosspieces are placed approximately one-third of the way in from both of the ends to support the baffles. Gluing and then screwing into the crosspieces from the back of the plywood adds strength to the box. Fiberglass batts are placed in the box. Planning ahead will save you some cutting. Once the fiberglass insulation is installed, cut a hole for the 4-inch vent pipe. The exact positioning will depend on the room where you are installing the heater. Make sure it can go through the wall between the wall studs.
Courtesy Katherine Walker (6)

The absorber plate is a prepainted piece of 4- by 10-foot aluminum, typically available from metal roofing suppliers. Prepainted steel is cheaper, but the aluminum transfers heat to the air more readily. Use gloves and eye protection when fabricating and handling metal parts, as the edges are sharp. Cut the dimension of the metal about 1/4 inch less than the interior dimension of the 1 by 4s around the edges, so that there is room for expansion. Fit the metal into the box. If it comes with a plastic film, leave that in place for now to prevent scratching the metal. Once the absorber plate is fit, cut the vent pipe holes. Cover the edge of the vent pipe with pencil graphite, then put the absorber in place, pressing it to the pipe to leave pencil outlines where the holes are to be cut. Now youre ready to cut out the hole in the metal. Use a large bit to drill a pilot hole, and then use tin snips to carefully follow the marked circle on the metal. Place the metal into the box and mark the center of the 1 by 2s that will support the baffles. All visible wood, including the baffles, will need to be painted with black, heat-resistant paint.

114

home power 145 october & november 2011

DIY heater

INSTALLATION
The installation begins. The sheet of metal has been removed from the box and placed on the wall to locate our two vent holes. Make sure the collector is positioned to avoid cutting any electrical wires in the wall. Studs also need to be avoided. In homes with exterior siding, you can determine stud position from the nailing pattern.

We positioned the fan at floor level to draw cooler air into the heater and promote overall mixing of air within the room. Forcing air upward into the heater works in tandem with the natural thermosiphon effect to create a steady flow through the heater. It also helps circulate air within in the room by drawing warmer air gradually toward floor level, where its wanted.
Stephen Hren

Once the holes are marked on the wall, drill a large pilot hole for the reciprocating saw blade and cut out the circle.

After placing the fiberglass insulation, we installed the metal absorber plate. We sealed it to the frame with a heat-resistant, highgrade silicone caulk to prevent air leakage. Nail a temporary board to support the heater while you position it. Shim it to the right spot (check by putting the vent pipes through the heater and into the office).

www.homepower.com

115

Courtesy Katherine Walker (3)

Stephen Hren

This wall had plywood sheathing and 1-inch-thick wood siding, so we felt comfortable using 3-inch lag screws and not worrying about penetrating the studs. If you have any doubt, however, go to the extra trouble of screwing into the studs. We put two lag screws near the top and two near the bottom.

Courtesy Katherine Walker (3)

DIY heater

INSTALLATION, CONT.
After the sheet metal was installed, rubbergasketed weather-stripping was stapled around the perimeter and on top of the baffles. Next, the vent pipe was cut to length, measuring from the inside of the wall to the outside of the heater and leaving an inch extra to cut into tabs. We siliconed around these tabs and pressed them into place.

The heater is mounted on the wall, with vent pipes installed, baffles in place, and weather-stripping ready to receive the polycarbonate glazing.

The polycarbonate glazing is tough, easy to install, and has low thermal mass. We predrilled the polycarbonate every 8 to 10 inches and attached it to the frame using metal roofing screws with neoprene washers.

A 30 W 12-volt nominal PV module used to power the fan was mounted on the exterior wall next to the heater. The fan and the PV module should be the same voltage, typically 12 VDC. The fan will have a power rating, labeled in watts. The fan we chose is an 8 W unit. At a minimum, the wattage of the PV module should be twice the wattage of the fan.

116

home power 145 october & november 2011

Stephen Hren

Courtesy Katherine Walker (5)

DIY heater

Backdraft Damper

Heres the setup inside the room: Even without the fan, air can flow through the heater by thermosiphon, causing unwanted cooling or heating. A back-draft damper keeps the system closed when the fan is not operating. We used a 4-inch dryer vent assembly, modifying it for aesthetics.
DC Switch

The DC fan moves about 100 cfm, doing well for this 18-square-foot heater. For a 4-by-8 heater (32 ft.2), 200 cfm would be appropriate. Size your PV module accordinglythe higher the air volume, the more power it will draw. A wood box provides nice finish detail around the fan. The DC switch shuts off electricity from PV module to fan when heating is not needed. PVC conduit and fittings were used since we didnt have access to the wall interior for running the wiring for the switch, fan, and PV module. For wiring the DC switch, the black (negative) wires are joined together with a wire nut, then taped. The red (positive) wire coming from the PV module goes to one side of the switch, the red (positive) going to the fan is wired onto the other side of the switch. Crimpedon ring terminals provide a secure connection. During all of the wiring, make sure the system isnt live by covering the PV module with a piece of cardboard.

DC Fan

T-Conduit Junction LB-Conduit Junction

Stephen Hren (2)

Wiring the Solar Fan

PV Module: 30 W, 12 V

DC Switch

DC Fan

Performance
Using an infrared temperature gun, we were able to determine that the air in the heater was heated by about 60F at midday (from 60F to 120F on the day of the installation). Earlier in the morning and later in the afternoon, the added heat was around 40F. After two winters, the heater is consistently capable of raising the temperature inside the building 15F on a sunny winter day. Some rough calculations of the amount of heat captured, based on a conservative efficiency of 50%, show that the 18-square-foot heater generates about 2,800 Btu per hour when in full sun (solar energy is about 317 Btu/ft.2). In the six hours the fan runs in the middle of winter (from about 9:30 a.m. to 3:30 p.m.), this adds up to 17,000 Btu, comparable to the heat energy of a pound of coal burned every three hours or a gallon of propane burned every five and a half days. Keep in mind that the size of our heater was confined by space and it would not have been much more money or trouble to make a 4- by 8-foot collector and almost double the heat output, assuming the fan and PV module were likewise upgraded. Payback for this heater will take longer as well, because of its smaller size and the relatively short winters here in North Carolina. Even so, it will save about a gallon of propane each week over our four-month heating season, saving roughly

www.homepower.com

117

DIY heater
Solar Air Heater
Air box materials Fan Collector plate Miscellaneous electrical PV module, 30 W (used) Total Solar Air Heater Cost $300 20 90 50 150 $610

$60 each year and paying back its $600 price (relatively high because we used new materials) in about 10 years. Since it is well-protected from the rain and out of the sun during the summer, we expect at least a 20-year lifespan of producing clean renewable, homemade energy.

Access
Stephen Hren ([email protected]) is a builder, teacher, and author focusing on sustainable design. He is the author of the upcoming book Tales from the Sustainable Underground and coauthor of The Solar Buyers Guide for the Home and Office and The Carbon-Free Home.

SOLAR TRAINING AT ITS BEST

Since 1991, Solar Energy International has provided expert instruction in solar, solar thermal, wind, and micro-hydro renewable energy technologies.

Visit solarenergy.org for our complete list of hands-on workshops and online courses. Start your solar training today.

Stephen Hren

Meet and greet the SEI team at Booth 1050 at Solar Power International in Oct in Dallas!

1991 - 2011

970.963.8855

R e g i s t e r o n l i n e a t s o l a re n e r g y. o r g
118
home power 145 october & november 2011

Celebrating 22 Years in Business!

SOLAR WATER HEATING

Commercial Residential Solar Radiant Floor

ON or OFF GRID?

The only simple way to integrate... Domestic Hot Water Electrical PV/Wind/Hydro Radiant Floor Heating Hot Tub Woodstove Propane Demand Boiler ... is with our SolarThermal Off Grid hot water tank See our website animated apps to learn more

20 YEAR TUBE WARRANTY

MADE IN THE UK FOR 31 YEARS
Heat Pipe Technology Plug & Play Connection Overheat Protection Lead-Free Soda Lime Glass Hail Impact Tested Deepest Vacuum Insulation Fast Installation Best All-Weather Performance

Our quality solar collector has a

1-888-923-9443 [email protected]

solarThermal.com
www.homepower.com

119

Announcing

THE FASTEST RACKING SYSTEM

Solar Electric

TAKE OF YOUR SOLAR WATER HEATING SYSTEM

Say hello to the Delta-T Pro.The most advanced solar hot water controller in the U.S. Solar energy production is uploaded and stored online for the life of your system. It also features remote, web-based monitoring and system adjustment settings along with automated email alerts. The future of solar water heating has arrived!

CONTROL

Racking & Foundation

Learn more and buy directly at deltatcontrols.com

2.7kW - 3 Hour Install Features Galvanized Steel Construction Structured Aluminum C Channel Helical Pier Foundation (concrete-less) Adjustable Angle 50%+ Labor Savings P.E. certified to IBC - Made in the USA 2.7 - 5.4 - 10.8 - 15.8 - 21.6kW sizes Complete Bundles Available panels - foundation - racking - inverters
by

The BEST Tool for Solar Site Analysis

JUST GOT BETTER!

USER FRIENDLY, FAST & ACCURATE!
The original Solar Pathfinder with its reflective properties gives an excellent instant solar blueprint of the prospective site. Now, the NEW Solar Pathfinder Assistant software, and your digital camera, carry that shading information into a concise, thorough, professional-looking solar site analysis report in just seconds. Solar Pathfinder Assistant: automatically adjusts for magnetic declination, latitude, azimuth, tilt angle, & tracking mode (fixed, 1-axis, 2 axis); automatically does yearly energy computations using included NREL data (no internet connection necessary); displays before/after results of removing obstructions; and creates professional-looking reports!

www.sunnrac.com (515)-720-0463 120

3953 Marsh Creek Road, Linden, TN 37096 317-501-2529 Fax 931-589-5400 [email protected] www.solarpathfinder.com

home power 145 october & november 2011

America, The Debate Ends Here:

SOLARSYZ = (Performance) Others = Just Adjectives

Solar Industrys Premier Wholesale Solar Supplier
Conergy, Trina Solar, Ecosolargy, Siliken, Lumos, Perlight Solar, Fluitecnik, ET Solar, Solon, Schuten, Sharp, Canadian Solar, Ritek & many more

1-877-786-0759 www.solarsyz.com Twitter: SolarSyz Facebook: SolarSyz

Brand New:

We are looking forward to your visit! Oct. 17 - 20, 2011 | Dallas, USA Booth 4824

Steca TR A501 T U, Steca TR A502 TT U and Steca TR A503 TTR U

A perfect trio: smart specialist, powerful allrounder and the optimizer Handy and favourable solutions for residential and commercial buildings, single-circuit or double-circuit systems. Easiest handling, everything pre-programmed always optimum efficient! Stecas latest solar controllers with extremely low electricity consumption. Eight resp. eleven pre-programmed solar thermal systems for a diverse range of applications. Additional PWM outputs for controlling high-efficiency pumps. Wall mounting or integration in solar stations. Steca TR A503 TTR U additionally offers functions for detailed system monitoring. Further information is available at: www.stecasolar.com Steca Elektronik GmbH | Germany | [email protected] | phone +49 (0) 8331 8558 - 0 | fax +49 (0) 8331 8558 - 132
Homepower_145_181x76_06_2011.indd 1 25.07.2011 09:11:58

w w w. m ave r i c k s o l a r. co m 5 1 2 9 1 9 4 4 9 3 o r d e r s @ m ave r i c k s o l a r. co m
www.homepower.com

121

code corner

renewable energy and the national electrical code

Sorting Out the Code

by Ryan Mayfield
The previous Code Corner introduced the 2011 National Electrical Code (NEC), its purpose, its fundamental requirements, and also included a few key phrases as defined in Article 100. This time, well explore a few more important definitions. As you read through materials that reference the NEC, pull out your Code book and open to the specific sections. It is one thing to read the distilled information presented in a magazine article, but to truly grasp it, you need to absorb it firsthand. Not all the definitions presented here are the full textand shouldnt be used as a replacement. Some definitions in the Code include informational notes that will help you even further, and if nothing else, paging through the book is an exercise that will help you navigate it better in the future. and documentable tests are outlined in different product standards. For example, utility-interactive inverters are tested to UL 1741, while enclosed switches are tested to UL 98. The product standard can be used by a number of NRTLs such as CSA, ETL, or UL to perform identical tests and properly list the inverter, disconnect, or whatever piece of equipment is being tested. The key for these three definitions lies in AHJ acceptance. Multiple times in the Code, youll see the requirement that the equipment be identified and listedSection 690.4(D) is one example. However, the identification and listing associated with products dont automatically mean they are acceptable and approved. For a refresher, go back to the definition of approved in Article 100. In nearly all situations, if a product carries a listing and is properly labeled as such, that product will be approved by the AHJ. You will need to verify that the product is identified for the installationjust because a utility-interactive inverter is listed to UL 1741 does not mean it is appropriate for your installation. If you plan to install the inverter outside, for example, you need to make sure it is properly identified for an outdoor location. There have been cases when an inverter was properly identified, listed, and labeled, but the installation did not pass inspection because the AHJ did not approve that equipment based on the listing NRTL. This is an extreme example that hasnt been a common problem in the PV industry but one that can occur and further illustrates the role and power of the AHJ. Moving further into the definitions: In Sight From (Within Sight From, Within Sight). Where the Code specifies that one piece of equipment shall be in sight from, within sight from, or within sight of, and so forth, another equipment, the specified equipment, is to be visible and not more than 50 feet from the other. There will be numerous times you run into a requirement that one piece of equipment needs to be installed in sight from another piece of equipment. Without this definition, the interpretations would be endless, but with the definition, we have a maximum distance value as well as the visual requirement. This definition is especially important when dealing with disconnecting means. For example 690.14(D) allows utility-interactive inverters to be installed in notreadily accessible locations, as long as a DC PV disconnecting means is mounted within sight of the inverter. In some cases, 690 has additional requirements, such as labeling based on equipment location. Two more definitions you need to have down pat:

Defining Code
To begin, Ill lump three definitions together: Identified (as applied to equipment). Recognizable as suitable for the specific purpose, function, use, environment, application, and so forth, where described in a particular Code requirement. Labeled. Equipment or materials which have a label, symbol, or other identifying mark of an organization that is acceptable to the authority having jurisdiction (AHJ) and is concerned with product evaluation; that maintains periodic inspection of the production of labeled equipment or materials; and by whose labeling the manufacturer indicates compliance with appropriate standards or performance in a specified manner. Listed. Equipment, materials, or services included in a list published by an organization that is acceptable to the AHJ and that is concerned with evaluation of products or services; that maintains periodic inspection of the production of listed equipment or materials or periodic evaluation of services; and whose listing states that either the equipment, material, or service meets appropriate, designated standards, or has been tested and found suitable for a specified purpose. When you first read these, the definitions seem similar, but there are some subtle differences. Product identification is required when the Code is concerned with very specific applications. Labeling and listing can be more general and typically are handled by nationally recognized testing laboratories (NRTLs) that test and verify product suitability. NRTLs are required to work from the same standards to make sure all products within a certain classification will behave the same when installed in the field. These repeatable

122

home power 145 october & november 2011

renewable energy and the national electrical code

code corner

Interactive System. An electric power production system that is operating in parallel with and capable of delivering energy to an electric primary source supply system. Utility-Interactive Inverter. An inverter intended for use in parallel with an electric utility to supply common loads that may deliver power to the utility. The majority of PV systems installed today are interactive systems. And while this is definitely on the decline, in some scenarios, you may be required to explain the PV systems functionality to the AHJ. The way the PV system interacts with and isolates itself from the utility in a grid disturbance (anti-islanding) is not universally understood and needs clarification at times. This definition becomes critical when you get into the methods allowed for interconnecting a PV system with a utility-interactive inverter to the primary energy sourcethe utility grid. The final definition must be addressed because there is a requirement called out in Section 690.4(E) based on this definition: Qualified Person. One who has skills and knowledge related to the construction and operation of the electrical equipment and installations and has received safety training to recognize and avoid the hazards involved. In most of the United States, only properly licensed individualsgenerally considered qualified persons can install electrical equipment. Since PV installations are relatively new, some states and jurisdictions dont have formal policies for the licensing requirements for PV systems. In some cases, only licensed electricians are legally allowed to work on PV systems, even if they havent received any PV-specific training. Most tradespeople will recognize their limitations and wont work with equipment they dont understand, but occasionally the opposite will happen, with potentially dangerous consequences. If there is any doubt

as to what constitutes a qualified person in your location, consult with the states electrical licensing division and make that clarification.

Generally Speaking
Next up in the Code is Article 110, Requirements for Electrical Installations. This article sets the basic requirements for all electrical installations. This Article has direct implications on your PV installations, so walking through it and highlighting applicable sections is well worth your time. In section 110.3(A), the Code lists items to consider when examining equipment. These items are intended to make sure the installed equipment is appropriate for its location and doesnt pose a hazard to anyone who might come into contact with it. Section 110.3(B) is another, often-quoted section of the Code. This section requires that all equipment be installed per the manufacturers instructions. If the manufacturers instructions are not followed completely, this blanket statement can make an entire electrical installation in violation of the NEC. I have seen installations that have passed inspection, even though a manufacturers instructions werent followed to a T. Some inspectors will allow such variations if they feel the installation is safe and meets the purpose and intent of Code. Generally speaking, inspectors realize that not all instructions are perfectly clear and in some cases, mistakes are found within the instructions. Article 110 has many more requirements and sections, which Ill discuss in the next Code Corner. Until then, crack open that Code and start studying!

Access
Ryan Mayfield ([email protected]) is the principal at a design, consulting and educational firm with a focus on PV systems in Corvallis, Oregon. He is a NABCEP-certified PV installer, an ISPQ Affiliated Master Trainer, and is proud to welcome his newest little achiever home.

Harris Hydro
Hydro-Power for Home Use
Adjustable Permanent Magnetic Brushless Alternator
25 - 30% more efficient than Hi Output Alternator Marine Grade Construction throughout Re-connectable Stator Retrofittable on existing turbine

Manufactured by Lo Power Engineering P.O. Box 1567 Redway, CA 95560

www.homepower.com

Denis Ledbetter 707-986-7771 [email protected] 123

Take your shade analysis to new heights.

Be safe and save time during site evaluations. With the SunEye Extension Kit from Solmetric, youll still get accurate shade measurements up to 18 feet from ground level.

Expert Tools. Better Solar.

www.solmetric.com

Why rent your power when you can own it?

MOBILE SOLAR GENERATOR

120v AC or 12v DC 3 - 100 Amp/Hr Batteries 1500w Inverter/Charger

Plug & Play - Point of use renewable energy for home, work or recreation.

Clean, Silent, and Portable

No Gas - No Fumes - No Hassle
Designed and Produced in America for High Quality and Lasting Value
INTEGRATED SOLUTIONS FOR ENERGY INDEPENDENCE

als

Special Expandable Option: Add 2 Extra PV Panels

600w smaller SolMan unit & 2000w Lithium Battery Model now available!

www.sol-solutions.com 800-828-2965
515 S. Main Street, Hwy 101, Willits, CA, 95490

124

home power 145 october & november 2011

THE FASTEST
Solar Electric

2.7kW - 3 Hour Install Features 50%+ Labor Savings Galvanized Steel Construction Structured Aluminum C Channel P.E. certified to IBC - Made in the USA Helical Pier Foundation (concrete-less) Adjustable Angle Complete 2.7kW Bundle Special: panels - foundation - racking - inverters $10,995

RACKING SYSTEM

www.sunnrac.com (515)-720-0463

THE SOLARSTATION

Americas Solar Thermal Leader Introduces

THINK THERMALTHINK SUNEARTH

SOLARSTATION AND CONTROL FOR CLOSED LOOP GLYCOL SYSTEMS

Complete Package Includes Pump Station, Differential Controller and Two Probe Sensors

Manufacturing quality solar energy products since 1978

www.sunearthinc.com
www.homepower.com

Distributor Inquires Welcome

125

home&heart

tales of off-grid living

Playing Chicken
by Kathleen Jarschke-Schultze
eggs for the first time) for $5 apiece. The woman lived nearby, so I loaded up my animal transport cages into my truck and off we went. On the way I told Bob-O, Ill get six hens. A couple of miles down the road, I amended that. Ill get eight, I said. We arrived to find a motley crew of mixedbreed hens running loose. It was up to us to catch them, so six was sounding better again. They were sprightly and healthylooking. Then the woman selling the hens came out with a couple of fishing nets and her two teenagers to help. I was an oak. I looked the woman right in the eye and said, Ill take 14, please. We quickly chased them up and down and filled my cages with 14 assorted hens. Since I wanted them to range free, I wanted to find a rooster for my newfound flock. I was at the local feed and seed getting some garden supplies when the woman there said, If you want chicks this year, now is the time to order them. I explained I already had 14 pullets and what I needed was a good rooster. She smiled widely. Why, a woman who left just before you got here put a notice on my board offering to give away a rooster, she said. I got the number off the board and called the woman on my cell phone. Yes, she had the rooster; did I have a cage? No, I was hoping she had a cardboard box, so I could just get him home. I got the directions and drove to her house.

My cousin Carrie once said, In our family, there are two phrases that will immediately stop and change the direction of any conversation. They are, Oooh, shiny! and Look, a chicken! It is too true. We are magpies, attracted to glittery objects; and we love poultry. In recent years, there has been a resurgence of small backyard flocks of chickens. This phenomenon has come about because people want to be more self-reliant, and the cost of food continues to rise as do the reports of unsafe, unhealthy food being sold to the public. Chickens take up only a small amount of space and are easily kept in a backyard. They eat food scraps and reward you with wonderfully bright-yellow-yolk eggs. Most towns will let you keep chickens within the city limits, although some have restrictions against keeping roosters. Roosters can be loud and obnoxious, especially just before dawn. However, if you are going to have a free-ranging flock, I highly recommend a rooster. Roosters will take care of the hens and break up fights. They also find succulent bugs and call the hens over to feast. Many a rooster has given up his life in defense of his hens. And, face it, they are just pretty to look at.

Raucous Rooster
There was a huge rooster, completely covered in glossy black plumage. He was sitting in a really nice, large dog cage. I told her I would bring the cage back but it would be a week or so. She didnt want the cage back. I was smiling as I drove off. I figured it was a double score for me, a big beautiful rooster and a nice big animal transport cage. I named the rooster Simon. My hens took to him right away. He took to the hens right away, which is what I expected. What I didnt expect was how mean he was. I could not turn my back on him. None of my previous roosters were so aggressive. The first time he got me I was walking down to the garden. He ran up behind, leapt in the air and spurred the back of my thigh, drawing blood right through my jeans. I whirled around in pain and surprise, and he pegged the front of my leg, again drawing blood. I kicked him away and went back to the house. I got on www.backyardchickens.com and searched for mean rooster. The advice I found was mostly: Eat em. One person gave me a methodology to deal with Simon.

Chicken Attrition
I was recently given the most beautiful rooster I had seen in a long time. Unfortunately, it is a grim tale, and Ill start at the beginning. While on our annual vacation, our house sitter neglected to close the chicken coop one night. We were between dogs at the time and that was all it took. I was suddenly left with only one hen, having lost the other eight hens and a wonderful rooster, Ned, to what I later determined was a family of raccoons. I gave the survivor to my sister Tamra and took a break from raising poultry. Then my husband Bob-O found an ad on our local Craigslist for pullets (young hens just about to start laying

126

home power 145 october & november 2011

tales of off-grid living

home& heart

Whenever he attacked I was to catch him, hold him down on the ground with his belly exposed, hold his beak, look him right in the eye and tell him I was the bigger, stronger rooster, and that he was not the alpha of the flock. I followed this advice for a couple of weeks, which meant that, several times a day, I was the alpha rooster. I still could not turn my back on Simon. I wrapped duct tape around his spurs to make them a little less dangerous. He seemed to have a learning disability.

An Ignoble End
The last straw was a sneak attack, when he jumped me from behind while I was walking to our shop. I was able to kick him back a few feet, but he flew at me again. The only weapon I could find to defend myself from his repeated attacks was a weatherworn, splintery 2 by 4 leaning against the garden fence. I parried his attacks for 10 minutes, getting splinters in my hands and losing any goodwill I had for the beast. I landed a pretty good hit that got him to move off far enough for me to back up all the way to the house. I waited till after dark to go close the coop that night. I told Bob-O that I had changed Simons name to Terry, short for Teriyaki. Tomorrow I vowed I would end his life. Bob-O let the chickens out to range the next morning. I cleaned the kindling axe and hung a cord across a low branch in the apple tree with slip loops on the ends. Donning a heavy

jacket and leather gloves, I was ready to take care of Simons antisocial problem. Bob-O went with me to find the chickens. He found them first and purposely turned his back on Simon. Simon flew at him, spurs up, but Bob-O whirled back around and caught the rooster in mid-air. Off with his head and into a bucket to bleed out. Hung in the tree by his legs, I made quick work of my problem rooster. As our hydro turbine was churning out plenty of electricity, I was indeed able to use my slow cooker to make chicken teriyaki that day. While not a great rooster, Simon proved to be a tasty dinner that evening here at our homestead. A couple of weeks later, when I celebrated my dads 94th birthday with my family, my sister gave me two Old English Bantam roosters, the Dos Amigos, hatched in her flock. They are wonderful with the hens and courteous to me. When I know them better, I will name them.

Access
Kathleen Jarschke-Schultze (kathleen.jarschke-schultze@homepower. com) is thoroughly enjoying her new Airedale dog-daughter, Josie, at her off-grid home in northernmost California.

AAA Solar Supply Inc.

FEATURING:

Serving the Solar Industry Since 1979

Also Featuring:

SUN AIRE
Liquid Collectors for Solar Hot Water & Radiant Floor Systems Other Solar H2O Products & Parts Pumps Heat Exchangers Storage Tanks Complete Systems Controls Batch Water Heaters

Air Collectors for Home Heating

Mounts Backdraft Damper Blower Air Collector

Hot Air

Control System

Cold Air

Other Solar Hot Air Products & Parts Blowers Backdraft Dampers Controls DIY Systems

(800) 245-0311 www.aaasolar.com [email protected]

2021 Zearing NW, Albuquerque, NM 87014
www.homepower.com

127

of racking

the king

So Simple its Scary!sm

855.670.1212 | zillarac.com
Visit us at Solar Power International 2011 Booth #4126

Made in USA. Patents pending.

128

home power 145 october & november 2011

Specializing in photovoltaic system design of any type.

Call one of our solar design technicians for system design or visit our web store for thousands of renewable energy products.

Solar Six Pack

2 3 1 2 3 1 Thermal Collector 4

TM

Quality, Simplicity, Plug & Play

Collector Overtemp Protection Solar Powered Pump Umbilical; Rubber Hose & Clamps Pump & Gauges Solar Wand

800-383-0195
5

OUR WAND HEATS

Qualifies for 30 % Federal Tax Credit

Made in
15 Lbs. 58 x 7 x 7

OG-300

USA
UP C
R

YOUR TANK
4091 E Huntington Dr Flagstaff, AZ 86004 Providing renewable energy since 1979

WAND IAPMO Listed

LEAD FREE CERTIFIABLE

http://store.solar-electric.com

33 Lbs. 24 x 20 x 12

800-983-1323 www.butlersunsolutions.com

BZ Products Model MPPT500

500 watt 45 amp Maximum Power Point Solar Control

A bright future is ahead with a degree in

Up to 45 amp output current 500 watt PV input Universal PV input 12 to 48 volts 12, 24 or 48 volt output

Renewable Energy

BZ Products Model MPPT250

250 watt 25 amp Maximum Power Point Solar Control

Up to 25 amp output current 250 watt PV input 12 to 48 volt PV input 15 amp low voltage disconnect standard Aux battery trickle charger standard, optional enclosure available PWM oat control Battery temperature sensor standard Five-year warranty Made in U.S.A.

Both Controllers offer: Boost charge current up to 30% Microprocessor control 95% efcient Digital metering

Degree & Certificate training in photovoltaic and solar thermal systems: In-depth coverage of solar Google SketchUp NEC compliance Excel spreadsheeting Affordable training Since 2000

SAN JUAN COLLEGE

For additional info about the Renewable Energy Program Call (866) 426-1233 or email [email protected]
129

314-644-2490 www.bzproducts.net [email protected] 7914 Gravois, St. Louis, MO 63123, USA

BZ Products, Inc.

www.sanjuancollege.edu/reng

School of Energy

www.homepower.com

User Friendly Hydro Power

Alternative Power & Machine

Now Featuring Permanent Magnet Alternators

4040 Highland Ave. Unit #H Grants Pass, OR 97526 541-476-8916 [email protected]

www.apmhydro.com

SOLAR POWERED
DIFFERENTIAL TEMPERATURE CONTROLLERS
control 12 Volt circulation pumps simple and reliable made in USA
www.ArtTecSolar.com

Things that Work!

Model 4-1850 Home Power #67

New USB plug in meter, up to 1 gig of flash memory!

Improves performance of PV pumped solar thermal systems

Brand Electronics
[email protected]

4-1850WX: Special meter for Refrigerator Replacement Programs. Detects Defrost Cycle, displays cost/kWh-hrs/yr.
Other Models available. Check our website or call for details.

ONEMeter: Standard Features include Multiple AC or DC power channels, PC interface, internal logging. Options include Web Interface, Weather Monitoring, and lots more.

Digital Power Meters

20-CTR: Measures AC Power up to 10

kW, 100250 vac single or two phase.

All products are California CEC eligible meters

Ordering or Information call

www.brandelectronics.com

Precision Wedge Wire Coanda Screens

Self Cleaning Easy Installation High Capacity No moving parts Pipe, ramp and box mountings Hydro, Agricultural, & Domestic Diversions from 10 gpm to 500 cfs Visit us at www.hydroscreen.com or call (303) 333-6071 e-mail [email protected]

BRUSHLESS HARDENED STAINLESS RUNNER BATTERIES OR GRID-TIE NO ADJUSTMENTS Head Range:30 - 500 Flow Range: 5 - 600gpm Power Range: DC Direct: 750W; 1500W AC/DC Units: 1200W - 4KW Transmission Voltage: DC Units: 12-120VDC AC Units: 240VAC or 440VAC Battery Voltage: 12, 24, 48V

(269)-365-7744

We dont just sell screens, we engineer solutions!

Experts in Renewable Energy Monitoring:

Non-recurring fees o Residential o WinVerter Software o Community Kiosks o Custom Solutions o Multi-site Telecom o Consulting Eighth page ad 1-11.pub Wednesday, January 19, 2011 15:43 On & Off Grid On-Site Displays page 1 Display, Log, Alarm Internet Accessible

RightHand Engineering, LLC

www.RightHandEng.com (425) 844-1291

130

home power 145 october & november 2011

guide to advertisers
A.O. Smith Corporation ..................................... 25 AAA Solar Supply,............................................ 127 ABS Alaskan Inc., ............................................ 130 Advanced Energy .............................................. 32 AEE Solar.............................................................. 3 Affordable Solar ................................................ 33 aleo solar ........................................................... 13 altE ...................................................................... 28 Alternative Power & Machine ......................... 130 Apex Solar .......................................................... 73 Array Technologies ........................................... 19 ART TEC .......................................................... 130 Astronergy.......................................................... 25 Aten Solar ........................................................ 103 Backwoods Solar ............................................. 84 Bogart Engineering ......................................... 110 Bornay .............................................................. 110 Brand Electronics ............................................ 130 Butler Sun Solutions ....................................... 129 BZ Products ..................................................... 129 Canadian Solar .................................................. 20 Central Lighting ............................................... 131 Delta Energy Systems ....................................... 43 EcoFasten Solar .............................................. 119 Electron Connection ......................................... 94 Energy Systems & Design............................... 119 Enphase Energy ................................................. 45 ET Solar .............................................................. 16 Fronius USA ....................................................... 21 Fullriver Battery USA ......................................... 84 groSolar .............................................................. 44 Harris Hydro ..................................................... 123 Hartvigsen-Hydro ............................................ 131 Heliodyne ................................................... 29, 120 Home Power Archive DVD ................................ 65 Hydro Induction Power ................................... 130 Hydrocap .......................................................... 124 Hydroscreen..................................................... 130 Iron Edison Battery Company ........................ 111 Lighthouse Solar................................................ 36 Magnum Energy................................................8/9 Maverick Solar Enterprises ............................ 121 MidNite Solar ............................................ 64, 125 MK Battery, ........................................................ 12 Morningstar ....................................................... 92 NABCEP ............................................................. 46 Northern Arizona Wind & Sun......................... 129 Northwest Energy Storage ............................. 102 ONTILITY ............................................................ 63 OutBack Power.............................................10/11 Power-One ......................................................... 24 PowerSpout ..................................................... 125 Quick Mount PV ................................................. 47 RAE Storage Battery ...................................... 130 REC ...................................................................... 2 RightHand Engineering ................................... 130 Rolls Battery Engineering ...............................IBC S-5! ...................................................................... 35 San Juan College............................................. 129 Sanyo Energy USA ..........................................BC Schletter ............................................................. 73 Schneider Electric ............................................... 5 Schott Solar ....................................................... 85 SMA America LLC. ...................................... 98, 99 SnapNrack.......................................................... 41 Solacity ............................................................... 18

ad index
Solar Data Systems ........................................... 27 Solar Depot/DC Power Systems .................IFC/1 Solar Energy International .............................. 118 Solar Pathfinder ............................................... 120 Solar Thermal 11............................................. 128 SolarBridge Technologies ................................ 95 SolarSyz............................................................ 121 SolarWorld.......................................................... 31 Solectria Renewables ....................................... 39 Solmetric ......................................................... 124 SolSolutions ..................................................... 124 Southwest Solar .............................................. 131 Steca ................................................................. 121 Stiebel Eltron ..................................................... 83 Sun Electronics................................................ 111 Sun Frost .......................................................... 124 Sun Pumps ........................................................ 82 SunDanzer ........................................................ 103 SunEarth ........................................................... 125 Sunflower Energy ............................................ 131 SunnRac ................................................... 120, 125 SunWize Technologies...................................... 74 SunXtender ........................................................ 56 The Solar Biz ...................................................... 37 Thermomax ...................................................... 119 Trina Solar .......................................................... 38 Trojan Battery .................................................... 17 U.S. Battery ........................................................ 93 Unirac ................................................................ 57 US Solar Distributing......................................... 34 Wholesale Solar ................................................... 4 Zilla Corporation .............................................. 128 Zomeworks ...................................................... 128

For easy online access to advertisers, visit www.homepower.com/resources/advertisers

A SWAMP COOLER IS NOT A HAPPY HOUR BEVERAGE Ultra Low Energy DC Cooling For Arid Climates

Watch for new lower cost models

Made in USA

www.southwest-solar.com

520.885.7925

Bulbs Spotlights Floodlights & More

A division of TOOLS PLUS

12 24 120 VOLT Amazingly Efficient

BRILLIANT WHITE LIGHT

High-Lumen LEDs
Mention this ad for a FREE catalog !
CENTRAL LIGHTING 2092

Hablamos Espaol Pregunte por Lynn

1-888-475-9697 217-543-3294 Fax 217-543-3296

CR 1800 E ARTHUR,

IL

61911

www.homepower.com

131

back page basics

renewable energy 101

PV Arrays & Galvanic Corrosion

Galvanic corrosion can have a significant impact on array structurescausing visible cosmetic corrosion to the farmore-serious structural component failure. Finding ways to minimize its effects are critical to ensure a long-lived system. For galvanic corrosion to take place, four things are required simultaneously: an anode, a cathode, an electrolyte, and a conductive path between two pieces of metal. A galvanic circuit is created when, with the assistance of an electrolyte, the anode loses electrons to the cathode. The galvanic cell created by two dissimilar metals and the presence of the electrolyte operates only in one direction. Consequently, the anode eventually disintegrates. In PV installations, the anode and cathode are metals, such as stainless steel, copper, or aluminum. Water commonly serves as the electrolyte. Whether galvanic corrosion is a serious problem depends on the potential failure point of the metal. For a PV installation, the long-term effects of corrosion can range from unsightly finishes to rack or fastener failure. The more dissimilar the metals, as designated by a 1 in the table, the greater the corrosion potential. For example, contact between copper and aluminum has a high potential for galvanic corrosion, but contact between aluminum and stainless steel does not. The local environment also influences the reaction. Generally, as humidity increases, so does the rate of corrosion. Atmospheric contaminants, such as chloride (in marine environments) and sulfur dioxide and nitrous oxides (in industrial locations), also increase corrosion rates. This is why PV systems installed in desert climates are less prone to galvanic corrosion than those located in coastal, humid, or industrial environments. Since PV arrays are sited in nearly all environments, installers must find practical ways to reduce galvanic corrosion. Methods include: Choosing metals that have a low potential for galvanic action (such as using stainless steel fasteners with aluminum racking);
Galvanic corrosion can cause failure of mechanical and electrical components.
Courtesy John Wiles

Selecting the appropriate protective coatings (such as paint, electroplating, or hot-dip galvanizing) to protect against environmental conditions; and Physically isolating dissimilar metals with nonconductive, nonporous materials, such as rubber washers with galvanized screws and painted steel; or stainless steel washers with an EPDM gasket already adhered. Certain plastics may also be suitable if they are rated for outdoor conditions. When it comes to PV system installation, problems with galvanic corrosion can stem from fastening hardware. Since much corrosion takes place at a bolted connection, the integrity of each connection is a concern. The fastener selected should not be anodic in relation to the metals being secured or held in place. In PV applications, 18/8 grade stainless fasteners meet this requirement. While stainless steel has become commonplace in PV hardware assemblies, Mudge Fasteners Dura-Con line uses coatings that reportedly meet or exceed the performance of stainless steel. Another area of concern with galvanic corrosion is with module grounding techniques. See Code Corner in HP137 for more information. Consult with equipment manufacturers about best practices that consider the climate, and with material trade associations, such as the American Galvanizers Association, that can offer guidance and summaries of research related to galvanic corrosion (www.galvanizeit.org). Erika Weliczko REPower Solutions

Galvanic Corrosion Potential Between Common Construction Metals

Aluminum Aluminum Copper Galvanized steel (zinc) Lead Stainless steel Zinc 1 3 2 3 3 Brass 1 2 2 2 1 1 Bronze 1 2 2 2 1 1 Copper 1 2 2 1 1 Galvanized Steel Iron/Steel 3 2 3 3 2 3 2 1 3 3 2 1 Lead 2 2 3 2 3 Stainless Steel 3 1 2 2 1 Zinc 3 1 3 3 1

1. Galvanic action will occur with direct contact; 2. Galvanic action may occur; 3. Galvanic action is insignificant between these metals. Source: Steel Tube Institute of North America

132

home power 145 october & november 2011

CAUTION

ONEMEANBATTERY

Available in 20 countries on 6 continents worldwide,

Rolls offers the broadest product line of deep cycle, low maintenance and maintenance free batteries for the Renewable Energy market. From large-scale storage to small village electrification, our flooded or AGM storage batteries deliver the power you need every time. Each is backed by our industry leading warranty, solid reputation and 97% recyclable at end of life. Green just got a whole lot meaner.

Superior Cycling | Dual-Container Construction | Widest Range of Specs Largest Liquid Reserves | Easiest to Install | Longest Life Span | Premium Warranties

T. 1.800.681.9914 E. [email protected] www.rollsbattery.com

in Dallas, TX Booth # 2508

SPI 2011

Visit us at