TED (22) –1002 REVISION – 2022

FIRST YEAR KGCE EXAMINATION

ENGINEERING DRAWING
MODEL QUESTION PAPER – ANSWER KEY
COMMON TO ALL KGCE PROGRAMS
(Time: 3 hours) (Maximum Marks: 60)

PART-A
(Maximum Marks: 20x1 Marks = 20 Marks)

I. Answer the following questions by choosing the correct answer from the options given below.
Each question carries 1 mark.

Q
Question Answer
No
1 Which of the following is the lightest pencil? d) H
To draw a smooth curve of any nature drawing instrument used
2 b) French curve
is?
b) Bottom right
3 A title block is normally drawn at of a drawing.
corner
4 The smallest std drawing sheet is designated as d) A4
5 The length to height ratio of a closed filled arrow head is ? b) 3:1
6 A simple octagon has _ no of sides? d) 8
7 Sectional portion of an object is represented by ? c) Hatching lines
The width across the corners of a hexagonal nut is represented in
8 c) 2d
terms of ‘d’ is?
9 Hatching lines are usually drawn at an angle of _? c) 45°
10 Minimum possible interior angle in a regular polygon is? c) 60°
For orthographic projection, the engineering custom Bureau of a) 1st angle
11
Indian Standards dictates the use of? projection
12 In 1st angle projection, the object is assumed to be situated in? a) 1st quadrant
13 In 1st angle projection, the top view will be drawn ? b) Below front view
a) Between
In orthographic projection, the object is assumed to be placed
14 observer and the
?
plane of projection
A cylinder is placed vertically in a horizontal plane (axis
15 perpendicular to the horizontal surface). Shape of its plan view c) Circle
(top view) will be? (Assume 1st angle projection)
16 The principle views associated with orthographic projection are? d) All of these
 Methods of dimensioning and tolerances in technical drawings
17 d) 10718-1983
are given by IS code?
 Q
Question Answer
No
18 The angle between the isometric axes is? d) 120°
19 A circle will appear in an isometric drawing as a _ ? b) Ellipse
A kind of drawing which provides complete details for the a) Shop floor
20
production/ fabrication is known as? drawing

PART-B
(Maximum Marks: 8x5 Marks = 40 Marks)

II. Answer any eight questions from the following. Each question carries marks.5 Marks.

Q
Question
No
1 List various instruments used in engineering drawing with their uses?
1. Drawing sheet - Drawing sheet is a white paper on which an object is drawn which is
available in various sizes.
2. Drawing board - Drawing board is generally made of soft wood and it is in rectangular
shape. It is used to support drawing sheet,
3. Mini drafter - Mini drafter is used for drawing horizontal lines, vertical lines, inclined
lines, angles, parallel lines, perpendicular lines etc.
4. T square - T square is used to draw horizontal and vertical lines on drawing sheet. It
made of wood or plastic and in T shape
5. Compass - Compass is used to draw an arc or circle with known dimensions on
engineering drawing.
6. Divider - This is used to divide a line or curve into equal parts. It is also used to check
the measurements.
7. Set squares - Set squares are used to draw lines with an angle between them. In most of
the structures, 30, 45, 60 and 90-degree lines are most common.
8. Protractor - Protractor is used to draw and measure the angles of lines in the drawing. It
is transparent and made of plastic.
9. French curves - French curves are made of plastic and they are in irregular shape.
10. Pencils - Pencil is used to draw on the paper. Different grades of pencils are used for
different line thicknesses.
11. Eraser - Eraser is used to remove the lines or spots which drawn by mistake or with
wrong measurements.
12. Paper holders - To fix the drawing sheet to the board paper holders are used.

2 Draw examples for different types of dimensioning methods used?

The different methods, arrangement and the indication of dimension are
 Chain or continuous Dimensioning
Q
Question
No
 Parallel Dimensioning

 Super imposed running dimensioning

 Combined Dimensioning

 Dimensioning by Co-ordinates
Q
Question
No
3 Draw freehand sketch of any four types of rivet heads?

4 Draw freehand sketch of ISO metric, Buttress & Square threads?

Q
Question
No
5 Draw an equilateral triangle in a given circle of diameter 50mm?

6 Construct a regular pentagon of side 40mm?

Q
Question
No
7 A line AB of 40mm length has its ends A&B 20mm above HP and 10mm in front of VP (1st
quadrant, parallel to both HP&VP). Draw its front and top view?

8 What are the differences between first and third angle projection. Show the drawing symbols
used in first angle and third angle projection?

Sl.No First Angle Projection Third Angle Projection

The object is placed in the first The object is placed in the third
1 quadrant. quadrant.

The object is placed between the plane The plane of projection is placed
2 of projection and observer. between the object and observer.

3 The plane of projection is opaque. The plane of projection is transparent.

Front view is at the top of the horizontal Front view at the bottom of the
4 axis. horizontal axis.

Top view at the bottom of the

5 horizontal axis. Top view at the top of horizontal axis.

Right view is at the left side of vertical Right view is at the right side of vertical
6 axis. axis.

Left view is at the right side of vertical Left view is at the left side of vertical
7 axis. axis.

It is widely used in Europe, India, It is widely used in United State and

8 Canada. Australia.
Q
Question
No

First Angle projection Third Angle projection

9 A stepped block is shown in below fig. Draw its front view?

Draw a hexagonal nut and bolt assembly for size M24?

10
Q
Question
No
Draw isometric view of a square prism, side of base 40mm and length 70mm when the axis of
the prism is horizontal. Assume that the adjacent side of the base is equally inclined to vertical
and horizontal planes?

11

A simple machine pin is given in the below drawing. Prepare a shop floor drawing of the
same by showing surface roughness, dimensional tolerance, geometrical tolerance (as a
minimum) by assuming required data?

12