Scribd
Upload
4 views

SM Syllabus

Download pdf files from online free download

Uploaded by

shivampatel0645
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
4 views

SM Syllabus

Download pdf files from online free download

Uploaded by

shivampatel0645
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

GOVERNMENT ENGINEERING COLLEGE, VALSAD

CIVIL ENGINEERING DEPARTMENT


INTERNAL EVALUATION-MID SEM EXAM-SYLLABUS

SUBJECT: SOIL MECHANICS (3150615)

Sr.
Content
No.
1. Stress Distribution of Soils: Causes of stress in soil, geostatic stress, Boussinesque’s equation,
stress distribution diagrams, New-mark’s influence chart Westergard’s equation, contact
pressure, stresses due to triangular and other loadings.
2. Subsurface Investigation: Objectives of exploration, planning of exploration program, soil
samples and soil samplers, field penetration tests: SPT, SCPT, DCPT.,Introduction to
geophysical methods, Bore log and report writing. Tests will be covered in lab sessions.
3. Pile foundations: Introduction, load transfer mechanism, types of piles according to their
composition, their method of installation and their load carrying characteristics, Negative skin
friction. Underreamed pile foundation-its concept

Course Cordinator

GOVERNMENT ENGINEERING COLLEGE, VALSAD


CIVIL ENGINEERING DEPARTMENT
INTERNAL EVALUATION TEST-SYLLABUS

SUBJECT: FOUNDATION ENGINEERING (3150615)


Sr.
Content
No.
1. Stress Distribution of Soils: Causes of stress in soil, geostatic stress, Boussinesque’s equation,
stress distribution diagrams, New-mark’s influence chart Westergard’s equation, contact
pressure, stresses due to triangular and other loadings.
2. Subsurface Investigation: Objectives of exploration, planning of exploration program, soil
samples and soil samplers, field penetration tests: SPT, SCPT, DCPT. Introduction to
geophysical methods, Bore log and report writing.
3. Pile foundations: Introduction, load transfer mechanism, types of piles according to their
composition, their method of installation and their load carrying characteristics, piles subjected
to vertical loads- pile load carrying capacity from static formula, dynamic formulae (ENR and
Hiley), penetration test data & Pile load test. Pile group: carrying capacity, efficiency and
settlement. Negative skin friction. Underreamed pile foundation-its concept, design & field
installation.

Prepared By:

HOD
Civil Engineering Dept.

GOVERNMENT ENGINEERING COLLEGE, VALSAD


CIVIL ENGINEERING DEPARTMENT
INTERNAL EVALUATION TEST-SYLLABUS

SUBJECT: DESIGN OF STRUCTURES (3150612)


Sr.
Content
No.
1. Introduction: Objectives, Properties of Reinforced Concrete and Structural Steel, Loads & load
combinations, Methods of Analysis, Codes & specifications, Design Philosophies - Working
stress Method, Ultimate Load Method, Limit State Method, Plastic Method
2. Philosophy of Limit state design for RC structures: Limit state of collapse & serviceability,
partial safety factors for material & loading. Limit State of Flexure: Stress-strain characteristics
of concrete & reinforcing steel, Type of section-under reinforced, over reinforced & balance
section, Neutral Axis depth, Moment of Resistance for singly reinforced, doubly reinforced and
flanged sections. Limit state of Axial, Shear and Torsion, combined flexure & torsion, Bond &
Anchorage, Development length, splicing
3. Limit state design of RC structural Element: Design of Beams: Simply supported, cantilever
and continuous beams
4. Philosophy of Limit state design for Steel: Limit state of collapse & serviceability, partial
safety factor for material and loading, Type & behavior of sections – Plastic, compact, semi-
compact, slender. Connections: Bolted connections – bearing type, behavior of bolted joints,
Design strength of ordinary & HSFG bolts. Welded connections- Fillet and Butt weld, design of
simple connections such as lap and butt joints, truss joint connections.

Prepared By:

HOD
Civil Engineering Dept.

You might also like