Scribd
Upload
49 views

Configuration Specification-IC Card

AS 380 series elevator IC Card access Dic switch note

Uploaded by

thawzin.61095
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
49 views

Configuration Specification-IC Card

AS 380 series elevator IC Card access Dic switch note

Uploaded by

thawzin.61095
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DQ/R-RD-23-05 (A/0)

Coding: -7
Version: V1.0
Configuration Instructions
Prepared by: Hu Jianmei
Date: 2015-08-03
Page Number: Page 1 of total 3 pages

Software version Circuit board name JT-02H

Basic Attributes
Communication protocol version Part of SmartCom II CAN Card protocol V4.0 – IC

Basic Functions
Card swipe status Functions
Normal card swipe Buzzer rings once
Number of times in the card is less than 10 times, or validity of period in Buzzer rings twice
the card is less than 7 days, and the card can be swiped normally
Invalid IC card (including wrong passcode, new card etc.) Buzzer rings 3 times (tentatively
set to not ring)
Outside call card can’t swipe on the floor Buzzer rings 3 times
Pass expiration date or insufficient balance in the card Buzzer rings 3 times
Not the card for the elevator (The card is not allowed to register for the Buzzer rings 3 times
elevator)
The time slot is stuck in a non-usable time or a usable date Buzzer rings 3 times
Registration card (the first time card swipe, at this time shall not deduct Buzzer rings 4 times
fees)
The elevator number is not received before, swipe the sub-elevator card (at Buzzer rings 5 times
this time shall not deduct fees)
No card swipe after the communication response (at this time shall not Buzzer rings 5 times
deduct fees)

Power sort setting ：


VDD VDD OUT OUT IN2 IN2 B A CAN CAN
IN1- IN1+ B1 A1
- + - + - + 2 2 H L
VDD-, VDD+: Connect with DC12—24V power
CANH, CANL: Connect to the new CAN port
Unspecified ports are reserved for alternate ports
LD1: Running lights
LD2: Reset lights
DIP switch:
SW1:
SW1.1: Charge position, ON is charge position, OFF is no charge position;
SW1.2: Reserved
SW2:
1-7 positions are used to set the position of the controller, including: the front door of vehicle, the rear door of
vehicle, the front lobby outside the N floor, the rear lobby N floor. 1-6 positions follow the 8421-coding method,
the first position of the DIP on-off switch represents 1, the second position represents 2, and the third position
represents 4. The number of the next position represents twice the number represented by the previous position, and
so on, and the sum of the numbers is the number of the floor in which the controller is located, toggle switch to
the number position is valid; When the 1-6-position toggle all the way to ON-side position, if the seventh position
toggle to ON-side, it represents the front door of vehicle, the 7th position to the OFF position represents the rear
door of vehicle; If there is any one or several switches to the OFF position, the 7th position will be toggled to the
ON terminal to represent the hallway outside the front lobby of N floor, and the 7th place to the OFF terminal to
represent the outside lobby of N floor. The eighth position is reserved.
The front lobby on the first floor is set as below:
DQ/R-RD-23-05 (A/0)
Coding: -7
Version: V1.0
Configuration Instructions
Prepared by: Hu Jianmei
Date: 2015-08-03
Page Number: Page 1 of total 3 pages

The front entrance hall on the sixth floor is set as: (2+4=6)

The rear entrance hall on the thirtieth floor is set as: (2+4+8+16=30)

Function Description:
：
1. Charge Card In the host computer card production is a charge card, for the sub-elevator number, when a
card is the first time swiped, the card swipe system will ring four times, this time there will be no output, the
system is registering the card, after it can be used normally. When buzzer rings once after a card swipe, the number
of valid times is more than 10 times (including 10 times); when buzzer rings twice after a card swipe, the number of
valid times is less than 10 times (not including 10 times); when buzzer rings three times after a card swipe, the
number of valid times is 0, and it need to be recharged;
2. Time-interval card: In the host computer, card production is a time-internal card, for the sub-elevator number,
when the new card is swiped, the system will ring four times, this time there will be no output, the system is
registering the card, after it can be used normally. When buzzer rings once after a card swipe, the number of valid
time is more than 7 days (including days); when buzzer rings twice after a card swipe, the number of valid time is
less than 7 days (not including 7 days); when buzzer rings three times after a card swipe, the card set the use of
time does not include the actual time, You must extend the use of time period before it can be used; or the card
can be used within the time period, but not in the valid date;
3. Facility Card: This card is done in the host computer, regardless of the elevator number, just finished, buzzer
will ring four times, which is registered card information. After it can be used normally, and buzzer will ring once
during normal usage.
4. Front rear door card swipe:
IC card authorized the front door and the rear door on the floor; the front door reader is only authorized to
open the front door, and the rear door reader is only authorized to open the rear door on the floor;
IC card is only with the front door or the rear door floor authorization, the IC whether the front door reader
or the rear door card reader, are authorized to open the corresponding floor card registration.
5. Outside lobby IC card swipe ：
Outside lobby IC swipe card reader only for the card to the side door on the floor is authorized; such as IC
card can only authorize for the front door on the third floor and the rear door on the fifth floor. The IC card can
only be effectively used at IC card reader of the front door on the third floor, as well as the rear door reader on
the fifth floor. The IC card can’t be effectively used at the rear door IC card reader on the third floor, the front
door IC card reader on the fifth floor, as well as IC card reader on the rest of floors, and buzzer rings three times.
Shanghai STEP Electric Corporation Proofreader ： Approve:
Date： Data:

You might also like