Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 17g

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2017 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
Read this material before using this
any shape or form without the express written consent of Harbor Freight Tools. product. Failure to do so can result in
Diagrams within this manual may not be drawn proportionally. Due to continuing serious injury. SAVE THIS MANUAL.
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
 Specifications
General Safety Warnings
WARNING Read all safety warnings and
instructions. Failure to follow the warnings
Drive Size 1/2″ and instructions may result in serious injury.
Accuracy + 2% Save all warnings and instructions
for future reference.
1/2″ - 3/8″
Included Adapters
1/2″ - 1/4″ 1. Wear ANSI-approved safety goggles during use.
Torque Range 29.5 ft-lb. to 147.5 ft-lb. 2. Do not exceed the Adapter's max. torque value.
Auto Shutdown After 70 Seconds
3. Do not mix old and new batteries.
Memory Stores up to 50 torque readings Do not mix alkaline, standard (carbon-
Battery Two AAA Batteries (Included) zinc), or rechargeable (nickel-cadmium)
batteries. Position batteries in proper polarity.
Do not use swollen or leaking batteries.
4. Use as intended only. Do not
Important Safety Information use as prybar or hammer.

In this manual, on the labeling, and all other 5. Do not submerge Adapter.
information provided with this product: 6. Do not disassemble Adapter.
This is the safety alert symbol. It is 7. Do not expose the Adapter to extreme
used to alert you to potential personal temperature, humidity, or direct sunlight.
injury hazards. Obey all safety
messages that follow this symbol 8. Do not excessively shake Adapter.
to avoid possible injury or death.
9. This product is not a toy. Keep it
out of reach of children.
10. The warnings, precautions, and instructions
DANGER indicates a hazardous situation which, if discussed in this instruction manual cannot
not avoided, will result in death or serious injury. cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
WARNING indicates a hazardous situation which, if but must be supplied by the operator.
not avoided, could result in death or serious injury.

CAUTION, used with the safety alert symbol,

indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.

NOTICE is used to address practices

not related to personal injury.

CAUTION, without the safety alert symbol, is used

to address practices not related to personal injury.

SAVE THESE INSTRUCTIONS.

Page 2 For technical questions, please call 1-888-866-5797. Item 63917

 6. Press the Memory (“M”) button and the “P/T” button
Instructions for Putting into Use at the same time to select the desired torque unit.
7. The Adapter contains three unit
Read the ENTIRE IMPORTANT selections: kg-m, ft-lb and N-m.
SAFETY INFORMATION section at the
beginning of this manual including 8. To increase the current torque value,
all text under subheadings therein press and hold down the Increase (“+”)
before set up or use of this product. button until value is reached.
9. To lower the current torque value,
Functions press and hold down the Decrease (“-”)
LED
Light
button until value is reached.
10. Note: The Display will show “00.0” if no
selection is made after ten seconds.
11. During operation, the LED light will flash GREEN.
12. Once you are 20% away from targeted torque, the
LED will flash YELLOW and the buzzer will beep.
13. When targeted torque is reached, the LED will
Display change to RED and a long buzz will sound.
14. To set peak torque, press and release
the “P/T” button when Adaptor is on.
Peak and Trace Power
15. The Display will show “PtoP” and
then “00.0” two seconds later.
16. To trace torque setting, press
and release “P/T” button.
17. The Display will show “trACE” and
then “00.0” two seconds later.
Decrease Increase
Torque Torque 18. To store a torque reading, have the Adapter
in “PtoP” mode. When you use it, the Adapter
can store the reading automatically.
Memory
19. Press the Memory button. The Display Panel
Anvil will show the stored reading as “P01”.
20. To show the second stored reading, press the
Memory button again for one second. The second
Operating Instructions torque value will be designated as “P02”.

Read the ENTIRE IMPORTANT 21. The Adapter can store up to fifty torque
SAFETY INFORMATION section at the values, the highest being “P50”.
beginning of this manual including
22. Note: “P50” will be the most recent saved
all text under subheadings therein
setting while “P01” will be the oldest.
before set up or use of this product.
23. If the torque setting is exceeded by 125%, the
1. Securely fasten Adapter to ratchet.
LED will flash RED and the alarm will beep.
2. Attach an adapter to end of anvil,
24. WARNING! Do not press the Memory and
if desired. Once fastened, press the Power
Power buttons at the same time. This will
button to activate the Adapter. The LCD
calibrate the tool and alter the preset values.
Display will show “trACE” and “PtoP.”
25. To turn off the Adapter, press the Power button
3. After two seconds, the Display will show “00.0”.
OR wait for the Adapter to turn off automatically.
4. Swing the Adapter. The Display will
26. Clean, then store the tool indoors
show the measured torque.
out of children's reach.
5. Note: If you do not use the Adapter for 70
seconds, the Adapter will automatically shut off.

Item 63917 For technical questions, please call 1-888-866-5797. Page 3

 Maintenance and Servicing

Procedures not specifically explained in this manual must be performed only by a

qualified technician.

Replacing Batteries Cleaning, Maintenance,

1. NOTE: When battery power is low, a and Lubrication
“ ” icon will appear on the display
1. BEFORE EACH USE, inspect the general
screen. Battery life will depend on battery
condition of the tool. Check for loose hardware,
quality and amount of hours tool is used.
misalignment or binding of moving parts, cracked
2. To replace batteries, unfasten screws or broken parts, damaged electrical wiring, and any
holding Battery Cap in place and other condition that may affect its safe operation.
remove Battery Cap from device.
2. AFTER USE, wipe external surfaces
3. Remove old batteries. of the tool with clean cloth.
4. Install new AAA batteries, making 3. Do not use cleaning agents to clean the
sure to follow indicated polarity. non-metal parts of the tool. Use only a
mild detergent or a damp cloth. Do not
5. Replace Battery Cap and screws. let water come into contact with tool.
6. Remove batteries if Torque Adapter
will be stored for a long time.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Record Product's Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797