3

FUEL–AIR CYCLES AND

THEIR ANALYSIS
3.1 INTRODUCTION

In the previous chapter, a detailed discussion of air-standard cycles, par-

ticularly for IC engines has been given. The analysis was based on highly
simplifying assumptions. Because of this, the estimated engine performance
by air-standard cycle analysis is on the higher side compared to the actual
performance. For example, the actual indicated thermal efficiency of an SI
engine, say with a compression ratio of 8:1, is of the order of 28% whereas
the air-standard efficiency is 56.5%. This large deviation may to some extent
be attributed to progressive burning of the fuel, incomplete combustion and
valve operation etc. However, the main reasons for this may be attributed to
the over simplified assumptions made in the analysis.
In an actual engine, the working fluid is a mixture of air, fuel vapour
and residual gases from the previous cycle. Further, the specific heats of the
working fluid are not constant but increase with temperature. Finally, the
products of combustion are subjected to certain dissociation at high temper-
atures. If the actual physical properties of the gases in the cylinder before
and after the combustion are taken into account, reasonably close values to
the actual pressures and temperatures existing within the engine cylinder can
be estimated. The mean effective pressures and efficiencies, calculated by this
analysis, in the case of well designed engines are higher only by a few per cent
from the actual values obtained by tests. The analysis based on the actual
properties of the working medium viz., fuel and air is called the fuel-air cycle
analysis and even this analysis has simplifying assumptions. However, they
are more justifiable and close to the actual conditions than those used in the
air-standard cycle analysis.

3.2 FUEL–AIR CYCLES AND THEIR SIGNIFICANCE

By air-standard cycle analysis, it is understood how the efficiency is improved

by increasing the compression ratio. However, analysis cannot bring out the
effect of air-fuel ratio on the thermal efficiency because the working medium
was assumed to be air. In this chapter, the presence of fuel in the cylinder is
taken into account and accordingly the working medium will be a mixture of
fuel and air. By fuel-air cycle analysis it will be possible to bring out the effect
of fuel-air ratio on thermal efficiency and also study how the peak pressures
and temperatures during the cycle vary with respect to fuel-air ratio. In
general, influence of many of the engine operating variables on the pressures
and temperatures within the engine cylinder may be better understood by
108 IC Engines

the examination of the fuel-air cycles. The fuel-air cycle analysis takes into
account the following :
(i) The actual composition of the cylinder gases : The cylinder gases con-
tains fuel, air, water vapour and residual gas. The fuel-air ratio changes
during the operation of the engine which changes the relative amounts
of CO2 , water vapour, etc.
(ii) The variation in the specific heat with temperature : Specific heats
increase with temperature except for mono-atomic gases. Therefore,
the value of γ also changes with temperature.
(iii) The effect of dissociation : The fuel and air do not completely combine
chemically at high temperatures (above 1600 K) and this leads to the
presence of CO, H2 , H and O2 at equilibrium conditions.
(iv) The variation in the number of molecules : The number of molecules
present after combustion depends upon fuel-air ratio and upon the pres-
sure and temperature after the combustion.
Besides taking the above factors into consideration, the following assump-
tions are commonly made :
(i) There is no chemical change in either fuel or air prior to combustion.
(ii) Subsequent to combustion, the charge is always in chemical equilibrium.
(iii) There is no heat exchange between the gases and the cylinder walls in
any process, i.e. they are adiabatic. Also the compression and expansion
processes are frictionless.
(iv) In case of reciprocating engines it is assumed that fluid motion can
be ignored inside the cylinder. With particular reference to constant-
volume fuel-air cycle, it is also assumed that
(v) The fuel is completely vaporized and perfectly mixed with the air, and
(vi) The burning takes place instantaneously at top dead centre (at constant
volume).
As already mentioned, the air-standard cycle analysis shows the general
effect of only compression ratio on engine efficiency whereas the fuel-air cy-
cle analysis gives the effect of variation of fuel-air ratio, inlet pressure and
temperature on the engine performance. It will be noticed that compression
ratio and fuel-air ratio are very important parameters of the engine while inlet
conditions are not so important.
The actual efficiency of a good engine is about 85 per cent of the estimated
fuel-air cycle efficiency. A good estimate of the power to be expected from the
actual engine can be made from fuel-air cycle analysis. Also, peak pressures
and exhaust temperatures which affect the engine structure and design can
be estimated reasonably close to an actual engine. Thus the effect of many
variables on the performance of an engine can be understood better by fuel-air
cycle analysis.
 Fuel–Air Cycles and their Analysis 109

3.3 COMPOSITION OF CYLINDER GASES

The air-fuel ratio changes during the engine operation. This change in air-fuel
ratio affects the composition of the gases before combustion as well as after
combustion particularly the percentage of carbon dioxide, carbon monoxide,
water vapour etc in the exhaust gases.
In four-stroke engines, fresh charge as it enters the engine cylinder, comes
into contact with the burnt gases left in the clearance space of the previous
cycle. The amount of exhaust gases in clearance space varies with speed and
load on the engine. Fuel-air cycle analysis takes into account this fact and the
results are computed for preparing the combustion charts. However, with the
availability of fast digital computers, nowadays it is possible to analyze the
effect of cylinder gas composition on the performance of the engine by means
of suitable numerical techniques. The computer analysis can produce fast and
accurate results. Thus, fuel-air cycle analysis can be done more easily through
computers rather than through manual calculations.

3.4 VARIABLE SPECIFIC HEATS

All gases, except mono-atomic gases, show an increase in specific heat with
temperature. The increase in specific heat does not follow any particular law.
However, over the temperature range generally encountered for gases in heat
engines (300 K to 2000 K) the specific heat curve is nearly a straight line
which may be approximately expressed in the form
Cp = a1 + k1 T
(3.1)
Cv = b1 + k1 T
where a1 , b1 and k1 are constants. Now,
R = Cp − Cv = a1 − b1 (3.2)
where R is the characteristic gas constant.
Above 1500 K the specific heat increases much more rapidly and may be
expressed in the form
Cp = a1 + k1 T + k2 T 2 (3.3)

Cv = b1 + k 1 T + k 2 T 2 (3.4)
2
In Eqn.3.4 if the term T is neglected it becomes same as Eqn.3.1. Many
expressions are available even upto sixth order of T (i.e. T6 ) for the calculation
of Cp and Cv .
The physical explanation for increase in specific heat is that as the tem-
perature is raised, larger fractions of the heat would be required to produce
motion of the atoms within the molecules. Since temperature is the result
of motion of the molecules, as a whole, the energy which goes into moving
the atoms does not contribute to proportional temperature rise. Hence, more
heat is required to raise the temperature of unit mass through one degree at
higher levels. This heat by definition is the specific heat. The values for Cp
and Cv for air are usually taken as
110 IC Engines

Cp = 1.005 kJ/kg K at 300 K Cv = 0.717 kJ/kg K at 300 K

Cp = 1.345 kJ/kg K at 2000 K Cv = 1.057 kJ/kg K at 2000 K

Since the difference between Cp and Cv is constant, the value of γ decreases
with increase in temperature. Thus, if the variation of specific heats is taken
into account during the compression stroke, the final temperature and pressure
would be lower than if constant values of specific heat are used. This point is
illustrated in Fig.3.1.

3 Cycle 1-2-3-4 : with constant specific heat

Cycle 1-2'-3'-4' : with variable specific heat
3' Cycle 1-2-3'-4" : with constant specific heat
from point 3'

p
2
2'

4
4'
4"
1

V
Fig. 3.1 Loss of power due to variation of specific heat

With variable specific heats, the temperature at the end of compression

will be 2 , instead of 2. The magnitude of drop in temperature is proportional
to the drop in the value of ratio of specific heats. For the process 1→2, with
constant specific heats
γ−1
v1
T2 = T1 (3.5)
v2

with variable specific heats,

k−1
v1
T2 = T1 (3.6)
v2
C
where k = Cvp . Note that v2 = v2 and v1 /v2 = v1 /v2 = r.
For given values of T1 , p1 and r, the magnitude of T2 depends on k. Con-
stant volume combustion, from point 2 will give a temperature T3 instead
of T3 . This is due to the fact that the rise in the value of Cv because of
variable specific heat, which reduces the temperature as already explained.
The process, 2 →3 is heat addition with the variation in specific heat.
From 3 , if expansion takes place at constant specific heats, this would result
in the process 3 →4 whereas actual expansion due to variable specific heat
 Fuel–Air Cycles and their Analysis 111

will result in 3 →4 and 4 is higher than 4 . The magnitude in the difference

between 4 and 4 is proportional to the reduction in the value of γ.
Consider the process 3 4
(k−1)
v3
T4 = T3 (3.7)
v4

for the process 3 4

(γ−1)
v3
T4 = T3 (3.8)
v4

Reduction in the value of k due to variable specific heat results in increase

of temperature from T4 to T4 .

3.5 DISSOCIATION

Dissociation process can be considered as the disintegration of combustion

products at high temperature. Dissociation can also be looked as the reverse
process to combustion. During dissociation the heat is absorbed whereas
during combustion the heat is liberated. In IC engines, mainly dissociation
of CO2 into CO and O2 occurs, whereas there is a very little dissociation of
H2 O.
The dissociation of CO2 into CO and O2 starts commencing around 1000
◦
C and the reaction equation can be written as

CO2 2CO + O2

Similarly, the dissociation of H2 O occurs at temperatures above 1300 ◦ C and

is written as
H2 O 2H2 + O2

The presence of CO and O2 in the gases tends to prevent dissociation of

CO2 ; this is noticeable in a rich fuel mixture, which, by producing more CO,
suppresses dissociation of CO2 . On the other hand, there is no dissociation in
the burnt gases of a lean fuel-air mixture. This is mainly due to the fact that
the temperature produced is too low for this phenomenon to occur. Hence, the
maximum extent of dissociation occurs in the burnt gases of the chemically
correct fuel-air mixture when the temperatures are expected to be high but
decreases with the leaner and richer mixtures.
In case of internal combustion engines heat transfer to the cooling medium
causes a reduction in the maximum temperature and pressure. As the temper-
ature falls during the expansion stroke the separated constituents recombine;
the heat absorbed during dissociation is thus again released, but it is too late
in the stroke to recover entirely the lost power. A portion of this heat is
carried away by the exhaust gases.
Figure 3.2 shows a typical curve that indicates the reduction in the temper-
ature of the exhaust gas mixtures due to dissociation with respect to air-fuel
ratio. With no dissociation maximum temperature is attained at chemically
112 IC Engines

correct air-fuel ratio. With dissociation maximum temperature is obtained

when mixture is slightly rich. Dissociation reduces the maximum tempera-
ture by about 300 ◦ C even at the chemically correct air-fuel ratio. In the
Fig.3.2, lean mixtures and rich mixtures are marked clearly.

3200

3000 No dissociation
Temperature ( oC)

2800

Stoichiometric mixture
2600
With dissociation

2400

2200
Lean Rich
2000
0.6 0.4 0.2 0 0.2 0.4 0.6
Degree of richness
Fig. 3.2 Effect of dissociation on temperature

The effect of dissociation on output power is shown in Fig.3.3 for a typical

four-stroke spark-ignition engine operating at constant speed. If there is no
dissociation the brake power output is maximum when the mixture ratio is
stoichiometric. The shaded area between the brake power graphs shows the
loss of power due to dissociation. When the mixture is quite lean there is no
dissociation. As the air-fuel ratio decreases i.e., as the mixture becomes rich
the maximum temperature raises and dissociation commences. The maximum
dissociation occurs at chemically correct mixture strength. As the mixture
becomes richer, dissociation effect tends to decline due to incomplete combus-
tion.
Dissociation effects are not so pronounced in a CI engine as in an SI engine.
This is mainly due to
(i) the presence of a heterogeneous mixture and
(ii) excess air to ensure complete combustion.
Both these factors tend to reduce the peak gas temperature attained in the
CI engine.
Figure 3.4 shows the effect of dissociation on p-V diagram of Otto cycle.
Because of lower maximum temperature due to dissociation the maximum
pressure is also reduced and the state after combustion will be represented by
3 instead of 3. If there was no reassociation due to fall of temperature during
expansion the expansion process would be represented by 3 →4 but due to
reassociation the expansion follows the path 3 →4 .
 Fuel–Air Cycles and their Analysis 113

bp
wi
th

Specific fuel consumption

no
diss
oci
ati
Brake power

on

Stoichiometric
mixture
bp

sfc
Rich Lean

11 12 13 14 15 16 17 18 19 20 21
Air-fuel ratio
Fig. 3.3 Effect of dissociation on power

3'

p
2

4
4'
4"
1
V
Fig. 3.4 Effect of dissociation shown on a p-V diagram

By comparing with the ideal expansion 3→4, it is observed that the effect
of dissociation is to lower the temperature and consequently the pressure at
the beginning of the expansion stroke. This causes a loss of power and also
efficiency. Though during recombining the heat is given back it is too late to
contribute a convincing positive increase in the output of the engine.

3.6 EFFECT OF NUMBER OF MOLES

As already mentioned the number of molecules present in the cylinder after

combustion depends upon the fuel-air ratio, type and extend of reaction in
the cylinder. According to the gas law

pV = N RT
114 IC Engines

the pressure depends on the number of molecules or moles present. This has
direct effect on the amount of work the cylinder gases can impart on the
piston.

3.7 COMPARISON OF AIR–STANDARD AND FUEL–AIR CYCLES

In this section reasons for difference between air-standard cycles and fuel-air
cycles is discussed. The magnitude of difference between the two cycles can
be attributed to the following factors :

(i) character of the cycle (due to assumptions)

(ii) equivalence ratio (actual F/A ÷ stoichiometric F/A)
(iii) chemical composition of the fuel

Figure 3.5 shows variation of efficiency with mixture strength of fuel-air

cycle relative to that of air cycle showing the gain in efficiency as the mixture
becomes leaner. It is seen from Fig.3.5 that the efficiency ratio (fuel-air cy-
cle efficiency/air-standard cycle efficiency) increases as the mixture becomes
leaner and leaner tending towards the air-standard cycle efficiency. It is to be
noted that this, trend exists at all compression ratios.

1.0
Efficiency ratio

0.8

0.6

0.2
0 0.4 0.8 1.2 1.6
Relative fuel-air ratio
Fig. 3.5 Effect of relative fuel-air ratio on efficiency ratio

At very low fuel-air ratio the mixture would tend to behave like a perfect
gas with constant specific heat. Cycles with lean to very lean mixtures tend
towards air-standard cycles. In such cycles the pressure and temperature
rises. Some of the chemical reactions involved tend to be more complete as
the pressure increases. These considerations apply to constant-volume as well
as constant-pressure cycles.
The simple air-standard cycle analysis cannot predict the variation of ther-
mal efficiency with mixture strength since air is assumed to be the working
medium. However, fuel-air cycle analysis suggests that the thermal efficiency
 Fuel–Air Cycles and their Analysis 115

will deteriorate as the mixture supplied to an engine is enriched. This is ex-

plained by the increasing losses due to variable specific heats and dissociation
as the mixture strength approaches chemically correct values. This is be-
cause, the gas temperature goes up after combustion as the mixture strength
approaches chemically correct values. Enrichment beyond the chemically cor-
rect ratio will lead to incomplete combustion and loss in thermal efficiency.
Therefore, it will appear that thermal efficiency will increase as the mixture
is made leaner. However, beyond a certain leaning, the combustion becomes
erratic with loss of efficiency. Thus the maximum efficiency is within the lean
zone very near the stoichiometric ratio. This gives rise to combustion loop,
as shown in Fig.3.6 which can be plotted for different mixture strengths for
an engine running at constant speed and at a constant throttle setting. This
loop gives an idea about the effect of mixture strength on the specific fuel
consumption.

Rich mixture

Fuel-
Act
Specific fuel consumption

ual

air th
cur

eory

Stoichiometric mixture
ve

Lean mixture

Enrich
Air standard theory

min. mep max. mep mep

Fig. 3.6 Specific fuel consumption vs. mean effective pressure at constant
speed and constant throttle setting

3.8 EFFECT OF OPERATING VARIABLES

The effect of the common engine operating variables on the pressure and
temperature within the engine cylinder is better understood by fuel-air cycle
analysis. The details are discussed in the following sections.

3.8.1 Compression Ratio

The fuel-air cycle efficiency increases with the compression ratio in the same
manner as the air-standard cycle efficiency, principally for the same reason
(more scope of expansion work). This is shown in Fig.3.7.
The variation of indicated thermal efficiency with respect to the equiva-
lence ratio for various compression ratios is given in Fig.3.8 The equivalence
ratio, φ, is defined as ratio of actual fuel-air ratio to chemically correct fuel-air
116 IC Engines

60
rd
a nda
r st
Ai
Thermal efficiency (%)
50
90
el
l fu 100
retica
eo
40 o f th
e
n tag 120
e
P erc

30 140

20
4 6 8 10
Compression ratio
Fig. 3.7 Effect of compression ratio and mixture strength on efficiency

0.65
22
0.60 18
16
14
0.55
Indicated thermal efficiency

12
10
0.50 9
8
0.45 7
r=6
0.40
Stoichiometric

0.35

0.30
Lean Rich
0.25
0.4 0.6 0.8 1.0 1.2 1.4 1.6

Equivalence ratio
Fig. 3.8 Effect of mixture strength on thermal efficiency
for various compression ratios
 Fuel–Air Cycles and their Analysis 117

ratio on mass basis. The maximum pressure and maximum temperature in-
crease with compression ratio since the temperature, T2 , and pressure, p2 , at
the end of compression are higher. However, it can be noted from the experi-
mental results (Fig.3.9) that the ratio of fuel-air cycle efficiency to air-standard
efficiency is independent of the compression ratio for a given equivalence ratio
for the constant-volume fuel-air cycle.

3.8.2 Fuel–Air Ratio

(i) Efficiency : As the mixture is made lean (less fuel) the temperature rise
due to combustion will be lowered as a result of reduced energy input
per unit mass of mixture. This will result in lower specific heat. Further,
it will lower the losses due to dissociation and variation in specific heat.
The efficiency is therefore, higher and, in fact, approaches the air-cycle
efficiency as the fuel-air ratio is reduced as shown in Fig.3.10.
Fuel-air cycle efficiency /

1.0 p1 = pe = 1.03 bar

Air-standard efficiency

0.9 T1 = 289 K
0.8
r= 4
0.7 r= 6
r= 8
0.6
r = 10
0.5
Rich
0.4
0 0.4 0.8 1.2 1.6 2.0 2.4
Equivalence ratio
Fig. 3.9 Variation of efficiency with mixture strength for a constant volume
fuel-air cycle
Stoic hiometric
Thermal efficiency

mixt ure

Air-standard theory

Ac Fu
tua el-
lv a
ari ir t
ati heo
o n ry

Weak Rich

Mixture strength
Fig. 3.10 Effect of mixture strength on thermal efficiency

(ii) Maximum Power : Fuel-air ratio affects the maximum power output
of the engine. The variation is as shown in Fig.3.11. As the mixture
118 IC Engines

becomes richer, after a certain point both efficiency and power output
falls as can be seen from the experimental curve (Figs.3.10 and 3.11).
This is because in addition to higher specific heats and chemical equilib-
rium losses, there is insufficient air which will result in formation of CO
and H2 during combustion, which represents a direct wastage of fuel.
However, fuel-air cycle analysis cannot exactly imitate the experimental
curve due to various simplifying assumptions made.

Stoichiometric
mixture
Air-standard theory
Cycle power

Fuel-air theory

tion
lvaria
A ctua
Lean Rich

70 80 90 100 110 120 130

Mixture strength expressed as a
percentage of stoichiometric mixture
Fig. 3.11 Effect of fuel-air ratio on power

(iii) Maximum temperature : At a given compression ratio the temperature

after combustion reaches a maximum when the mixture is slightly rich,
i.e., around 6% or so (F/A = 0.072 or A/F = 14 : 1) as shown in
Fig.3.12. At chemically correct ratio there is still some oxygen present
at the point 3 (in the p-V diagram, refer Fig.3.1) because of chemical
equilibrium effects a rich mixture will cause more fuel to combine with
oxygen at that point thereby raising the temperature T3 . However, at
richer mixtures increased formation of CO counters this effect.

(iv) Maximum Pressure : The pressure of a gas in a given space depends

upon its temperature and the number of molecules The curve of p3 ,
therefore follows T3 , but because of the increasing number of molecules
p3 does not start to decrease until the mixture is somewhat richer than
that for maximum T3 (at F/A = 0.083 or A/F 12 : 1), i.e. about 20 per
cent rich (Fig.3.12).

(v) Exhaust Temperature : The exhaust gas temperature, T4 is maximum

at the chemically correct mixture as shown in Fig.3.13. At this point
the fuel and oxygen are completely used up, as the effect of chemical
equilibrium is not significant. At lean mixtures, because of less fuel,
T3 is less and hence T4 is less. At rich mixtures less sensible energy is
developed and hence T4 is less. That is, T4 varies with fuel-air ratio in
the same manner as T3 except that maximum T4 is at the chemically
correct fuel-air ratio in place of slightly rich fuel-air ratio (6%) as in
case of T3 . However, the behaviour of T4 with compression ratio is
 Fuel–Air Cycles and their Analysis 119

3000

2800 r
T3 (K) 10
8
2600 6
4
2400

Stoichiometric
mixture
2200
120
r
100 10
80
8
p (bar)
3 60
6
40
4
20
0
60 80 100 120 140 160
Mixture strength expressed as a percentage
of stoichiometric mixture
Fig. 3.12 Effect of equivalence ratio on T3 and p3

different from that of T3 as shown in Fig.3.13. Unlike T3 , the exhaust

gas temperature, T4 is lower at high compression ratios, because the
increased expansion causes the gas to do more work on the piston leaving
less heat to be rejected at the end of the stroke. The same effect is
present in the case of air-cycle analysis also.

2200

2000
Temperature, T (K)

r
4

1800 4
6
Stoichiometric

1600 8
10
mixture

1400

1200
60 80 100 120 140 160
Per cent of theoretical fuel
Fig. 3.13 Effect of fuel-air ratio on the exhaust gas temperature

(vi) Mean Effective Pressure (mep) : The mean effective pressure increases
with compression ratio. It follows the trend of p3 and p4 and hence it is
maximum at a fuel-air ratio slightly richer than the chemically correct
ratio as shown in Fig.3.14. Table 3.1 shows a summary of conditions
which give maximum pressure and temperature in a constant-volume
cycle assuming fuel-air cycle approximations.
120 IC Engines

18

16
r
14 10
Mean effective pressure (bar) 8
12
6
10
4
8

0
60 80 100 120 140 160
Percent of theoretical fuel
Fig. 3.14 Effect of fuel-air ratio on mep

Table 3.1 Condition for maximum temperature and pressure in a constant

volume fuel-air cycle

Variable Maximum at Reason

1. Temperature, T3 6% rich, F/A = 0.072; Because of chemical equilib-

(Fig.3.12) A/F = 14 : 1, φ = 1.06 rium some O2 still present
even at chemically correct
F/A ratio. More fuel can be
burnt. Limit is reached at
6% rich. If > 6% rich CO
formation.

2. Pressure, p3 20% rich, F/A = 0.083; pV = N RT.

(Fig.3.12) A/F = 12 : 1 p depends on T and N

3. Temperature, T4 Chemically correct No effect of chemical equi-

(see Fig.3.13) fuel-air ratio librium due to low temper-
ature and incomplete com-
bustion at rich mixture.

4. Mean effective 6% rich, F/A = 0.0745; mep follows the trend of p3

pressure (Fig.3.14) A/F =13.5,φ=1.05 to 1.1 and p4 .
 Fuel–Air Cycles and their Analysis 121

Worked out Examples

3.1 What will be the effect on the efficiency of an Otto cycle having a
compression ratio of 8, if Cv increases by 1.6%?

Solution
1
ηOtto = 1−
rγ−1
Cp R
Cp − Cv = R; = γ and γ−1 =
Cv Cv
R/Cv
1
η = 1−
r

1−η = r−R/Cv
−R
ln(1 − η) = ln r
Cv

Differentiating
1 R
− dη = ln rdCv
1−η Cv2

(1 − η)R ln r
dη = − dCv
Cv2

dη (1 − η)(γ − 1) ln r dCv
= −
η η Cv
0.4
1
η = 1− = 0.565 = 56.5%
8

dη (1 − 0.565) × (1.4 − 1) × ln 8 1.6

= − ×
η 0.565 100
Ans
= −1.025% ⇐=

3.2 What will be the effect on the efficiency of a diesel cycle having a com-
pression ratio of 20 and a cut-off ratio is 5% of the swept volume, if the
Cv increases by 1%. Take Cv = 0.717 and R = 0.287 kJ/kg K.

Solution
γ−1
1 1 rcγ − 1
ηDiesel = 1−
r γ rc − 1

1 rcγ − 1
1−η =
γ rγ−1 (rc − 1)
122 IC Engines

Taking logarithm

ln(1 − η) = − ln γ + ln(rcγ − 1) − ln(rc − 1) − (γ − 1) ln r

R
γ−1 =
Cv

R
γ = 1+
Cv

Substituting this in the above equation

R ( R +1) R
ln(1 − η) = − ln + 1 + ln rc Cv − 1 − ln(rc − 1) − ln r
Cv Cv

Differentiating we get,
R ( R +1)
R rc Cv ln rc dCv
Cv2 dCv
dη Cv2 R
− = R
− + ln rdCv
η Cv + 1
( CRv +1) Cv2
rc −1
dη dCv R 1 − η
= −
η C v Cv η
⎛ R
⎞
Cv +1
1 rc ln(rc ) ⎠
× ⎝ R + ln r − R
+ 1 Cv +1
Cv rc −1

dη dCv 1−η 1 rγ ln(rc )

= − (γ − 1) + ln r − c γ
η Cv η γ rc − 1

γ = 1.4
V1
= r = 20
V2
V1 = 20V2

Vs = 20V2 − V2 = 19V2

V3 = 0.05Vs + V2 = (0.05 × 19V2 ) + V2 = 1.95V2

V3 1.95V2
rc = = = 1.95
V2 V2
1 1 rcγ − 1
η = 1− γ−1
γ r rc − 1
0.4
1 1 1.951.4 − 1
= 1− × × = 0.649
1.4 20 1.95 − 1
 Fuel–Air Cycles and their Analysis 123

dη 1 − 0.649
= −0.01 ×
η 0.649

1 1.951.4 × ln(1.95)
×0.4 × + ln(20) −
1.4 1.951.4 − 1
Ans
= −0.565% ⇐=

3.3 A petrol engine having a compression ratio of 6 uses a fuel with calorific
value of 42 MJ/kg. The air-fuel ratio is 15:1. Pressure and temperature
at the start of the suction stroke is 1 bar and 57 ◦ C respectively. Deter-
mine the maximum pressure in the cylinder if the index of compression
is 1.3 and the specific heat at constant volume is given by Cv = 0.678 +
0.00013 T, where T is in Kelvin. Compare this value with that obtained
when Cv = 0.717 kJ/kg K.

Solution Consider the process 1-2

p2 V2n = p1 V1n
n
V1
p2 = p1 = 1 × 61.3 = 10.27 bar
V2

p2 V2 10.27 1
T2 = T1 = 330 × × = 565 K
p1 V1 1 6

T 3 + T2
Average temperature during combustion =
2
T3 + T 2
Cvmean = 0.678 + 0.00013 ×
2

Assuming unit quantity of air

42
Q2−3 /kg of air = = 2.8 MJ
15
1 16
Mass of charge = 1+ = kg/kg of air
15 15
Q2−3 = Cvmean ṁ(T3 − T2 )

T3 + 565
2.8 × 103 = 0.678 + 13 × 10−5 ×
2

16
× × (T3 − 565)
15
T3 = 3375 K
T3 3375 Ans
p3 = p2 = 10.27 × = 61.35 bar ⇐=
T2 565
124 IC Engines

For constant specific heat

16
2.8 × 103 = 0.717 × × (T3 − 565)
15
T3 = 4226
4226 Ans
p3 = 10.27 × = 76.81 bar ⇐=
565
3.4 The air-fuel ratio of a Diesel engine is 29:1. If the compression ratio is
16:1 and the temperature at the end of compression is 900 K, find at
what cylinder volume the combustion is complete? Express this volume
as a percentage of stroke. Assume that the combustion begins at the top
dead centre and takes place at constant pressure. Take calorific value of
the fuel as 42000 kJ/kg, R = 0.287 kJ/kg K and Cv = 0.709+0.000028 T
kJ/kg K.

Solution
Cp = Cv + R

= (0.709 + 0.000028 T ) + 0.287

= 0.996 + 0.000028 T

dQ = mCp dT
3
For unit mass, Q = Cp dT
2

For 1 kg of fuel the total charge is 30 kg

CV 42000
Q = = = 1400
30 30
3
= (0.996 + 0.000028 T )dT
2

0.000028 2
= 0.996(T3 − T2 ) + T3 − T22
2
= 0.996 × (T3 − 900) + 0.000014 × T32 − 9002

T3 = 2246.07 K
T3 2246.07
V3 = V2 = V2 = 2.496 V2
T2 900

V1
Vs = V1 − V 2 = V 2 −1 = V2 (r − 1) = 15 V2
V2

V3 2.496 × V2 Ans
= × 100 = 16.64% ⇐=
Vs 15 × V2
 Fuel–Air Cycles and their Analysis 125

3.5 An oil engine, working on the dual combustion cycle, has a compression
ratio of 13:1. The heat supplied per kg of air is 2000 kJ, half of which is
supplied at constant volume and the other half at constant pressure. If
the temperature and pressure at the beginning of compression are 100
◦
C and 1 bar respectively, find (i) the maximum pressure in the cycle
and (ii) the percentage of stroke when cut-off occurs. Assume γ = 1.4,
R = 0.287 kJ/kg K and Cv = 0.709 + 0.000028T kJ/kg K.

Solution

p1 V1γ = p2 V2γ
γ
V1 2
p2 = p2 = 1 × 105 × 131.4 = 36.27 × 105 N/m
V2
(γ−1)
T 1 V1 = T2 V2γ−1

T2 = T1 r(γ−1) = 373 × 130.4 = 1040.6 K

For unit mass :

Consider the process 2-3,
1
Q2−3 = × 2000 = 1000 kJ
2
3
Q2−3 = m (0.709 + 0.000028T )dT
2

0.000028
1000 = 0.709 × (T3 − 1040.6) + × T32 − 1040.62
2
T3 = 2362.2 K

T3 2362.2
p3 = p2 = 36.27 × × 105
T2 1040.6

2 Ans
= 82.34 × 105 N/m ⇐=

Consider the process 3-4,

1
Q3−4 = × 1000 = 500 kJ
2
Cp = Cv + R = 0.996 + 0.000028 T
4
Q3−4 = m dT
3

4
500 = (0.996 + 0.000028)dT
3
126 IC Engines

0.000028
= 0.996 × (T4 − 2362.2) + × T42 − 2362.22
2
T4 = 2830.04 K

T4 2830.04
V4 = V3 = V3 = 1.198 V3
T3 2362.2

Vs = V 1 − V3 = V3 (r − 1) = 12 V3

V 4 − V3 V4 − V3
Cut-off % = × 100 = × 100
Vs 12 V3
1.198 − 1 Ans
= × 100 = 1.65% ⇐=
12

3.6 A petrol engine with a compression ratio of 7 used a mixture of iso-

octane and hexane as fuel. The pressure and temperature at the begin-
ning of the compression process is 1 bar and 55.22 ◦ C respectively. If
the fuel-air mixture is 19.05% rich and the maximum pressure developed
is 115.26 bar then evaluate the composition of the mixture (in percent-
age weight). Take Cv = 0.717 kJ/kg K, (CV )hexane = 43 MJ/kg,
(CV )iso-octane = 42 MJ/kg and pV 1.31 is constant for the expansion
and compression processes.

Solution
Suppose every kmol of iso-octane is mixed with x kmols of hexane. The
stoichiometric equation is

xC6 H14 + C8 H18 + y(0.21 O2 + 0.79 N2 ) →

(8 + 6x)CO2 + (9 + 7x) H2 O + (0.79y)N2

Equating number of oxygen atoms on both sides

0.42y = 2 × (8 + 6x) + (9 + 7x)

1
y = × (25 + 19x)
0.42
As the fuel-air mixture is 19.05% rich, for x moles of hexane and 1 mole of
iso-octane, number of moles of air present
y
= = (50 + 38x)
1.1905
The combustion equation may now be written as

xC6 H14 + C8 H18 + (50 + 38x)(0.21 O2 + 0.79 N2 ) →

aCO2 + b CO + (9 + 7x) H2 O + 0.79(50 + 38x)N2

Equating number of carbon atoms

 Fuel–Air Cycles and their Analysis 127

a+b = 6x + 8 (1)

Equating number of oxygen atoms

2a + b = 8.96x + 12 (2)

On solving Eqs.(1) and (2)

a = 2.96x + 4

b = 3.04x + 4
nf 56.5 + 43.02x
=
ni 51 + 39x

State 2:
p2 = p1 rn = 12.796 bar

T2 = T1 rn−1 = 600 K

Now, consider (50 + 38 x) kmols of air

Molecular weight of C6 H14 = 86 kg/kmol and molecular weight of C8 H18 =
114 kg/kmol. Therefore,
Heat added = 86x × 43 × 103 + 114 × 42 × 103

= (3698x + 4788) × 103 kJ

Total weight = 28.97 × (50 + 38x) + (86x + 114)

= (1186.86x + 1562.5) kg

Qs = mCv (T3 − T2 )

(3698x + 4788) × 103 = (1186.86x + 1562.5) × 0.717 × (T3 − T2 )

3698x + 4788 4208.6x + 5460
T3 = 600 + =
0.851x + 1.120 0.851x + 1.120
T3 nf
p3 = p2
T2 ni

12.796 4208.6x + 5460 43.02x + 56.5

115.26 = × ×
600 0.851x + 1.120 39x + 51

Solving this we get x = 0.1. Therefore, percentage weight of iso-octane

114 Ans
= × 100% = 93% ⇐=
114 + 86x

Percentage weight of hexane

86x Ans
= × 100% = 7% ⇐=
114 + 86x
128 IC Engines

Review Questions

3.1 Mention the various simplified assumptions used in fuel-air cycle anal-
ysis.
3.2 What is the difference between air-standard cycle and fuel-air cycle anal-
ysis? Explain the significance of the fuel-air cycle.
3.3 Explain why the fuel-air cycle analysis is more suitable for analyzing
through a computer rather than through hand calculations.
3.4 How do the specific heats vary with temperature? What is the physical
explanation for this variation?
3.5 Explain with the help of a p-V diagram the loss due to variation of
specific heats in an Otto cycle.
3.6 Show with the help of a p-V diagram for an Otto cycle, that the effect
of dissociation is similar to that of variation of specific heats.
3.7 Explain by means of suitable graphs the effect of dissociation on maxi-
mum temperature and brake power. How does the presence of CO affect
dissociation?
3.8 Explain the effect of change of number of molecules during combustion
on maximum pressure in the Otto cycle.
3.9 Compare the air-standard cycle and fuel-air cycles based on (i) character
of the cycle (ii) fuel-air ratio (iii) chemical composition of the fuel
3.10 Is the effect of compression ratio on efficiency the same in fuel-air cycles
also? Explain.
3.11 From the point of view of fuel-air cycle analysis how does fuel-air ratio
affect efficiency, maximum power, temperature and pressure in a cycle.
3.12 How does exhaust temperature and mean effective pressure affect the
engine performance? Explain.

Exercise

3.1 Find the percentage change in the efficiency of an Otto cycle having a
compression ratio of 10, if Cv decreases by 2%. Ans: 1.22%
3.2 Find the percentage increase in the efficiency of a Diesel cycle having a
compression ratio of 16 and cut-off ratio is 10% of the swept volume, if
Cv decreases by 2%. Take Cv = 0.717 and γ = 1.4. Ans: 1.23%
3.3 The air-fuel ratio of a Diesel engine is 31:1. If the compression ratio is
15:1 and the temperature at the end of compression is 1000 K, find at
what percentage of stroke is the combustion complete if the combustion
begins at T DC and continuous at constant pressure. Calorific value of
the fuel is 40000 kJ/kg. Assume the variable specific heat, Cp = a + bT ,
where a = 1 and b = 0.28 × 10−4 . Ans: 15.68%
 Fuel–Air Cycles and their Analysis 129

3.4 An engine working on the Otto cycle, uses hexane (C6 H14 ) as fuel. The
engine works on chemically correct air-fuel ratio and the compression
ratio is 8. Pressure and temperature at the beginning of compression
are 1 bar and 77 ◦ C respectively. If the calorific value of the fuel is
43000 kJ/kg and Cv = 0.717 kJ/kg K, find the maximum temperature
and pressure of the cycle. Assume the compression follows the law
pV 1.3 = c. Ans: (i) 4343.6 K (ii) 99.28 bar
3.5 Find the percentage change in efficiency of a dual cycle having com-
pression ratio = 16 and cut-off ratio of 10% of swept volume and if Cv
increases by 2%. Given TT32 = 1.67. Ans: 0.68%
3.6 It is estimated that for air operating in a given engine the γ decreases
by 2% from its original value of 1.4. Find the change in efficiency. The
pressure at the end of compression is 18 bar. Ans: 4.5%

Multiple Choice Questions (choose the most appropriate answer)

1. The actual efficiency of a good engine is about

(a) 100%
(b) 85%
(c) 50%
(d) 25%

of the estimated fuel-air cycle efficiency.

2. With dissociation peak temperature is obtained

(a) at the stoichiometric air-fuel ratio

(b) when the mixture is slightly lean
(c) when the mixture is slightly rich
(d) none of the above

3. With dissociation the exhaust gas temperature

(a) decreases
(b) increases
(c) no effect
(d) increases upto certain air-fuel ratio and then decreases

4. Fuel-air ratio affects maximum power output of the engine due to

(a) higher specific heats

(b) chemical equilibrium losses
(c) both (a) and (b)
(d) none of the above
130 IC Engines

5. Mean effective pressure at a given compression ratio is maximum when

the air-fuel ratio is
(a) higher than stoichiometric
(b) lower than stoichiometric
(c) equal to stoichiometric
(d) none of the above
6. For a compression process with variable specific heat the peak temper-
ature and pressure are
(a) lower
(b) higher
(c) no effect
(d) none of the above
compared to constant specific heat
7. Dissociation can be considered as
(a) disintegration of combustion products at high temperature
(b) reverse process of combustion
(c) heat absorption process
(d) all of the above
8. Cycles with lean to very lean mixture tend towards
(a) practical cycles
(b) fuel-air cycles
(c) air-standard cycles
(d) none of the above
9. When the mixture is lean
(a) efficiency is less
(b) power output is less
(c) maximum temperature and pressure are higher
(d) all of the above
10. For a given compression ratio, as the mixture is made progressively rich
from lean the mean effective pressure
(a) increases
(b) decreases
(c) initially increases and then decreases
(d) remains more or less same

Ans: 1. – (b) 2. – (c) 3. – (a) 4. – (c) 5. – (b)

6. – (a) 7. – (d) 8. – (d) 9. – (b) 10. – (c)
 4
ACTUAL CYCLES AND
THEIR ANALYSIS
4.1 INTRODUCTION

The actual cycles for IC engines differ from the fuel-air cycles and air-standard
cycles in many respects. The actual cycle efficiency is much lower than the
air-standard efficiency due to various losses occurring in the actual engine
operation. The major losses are due to:

(i) Variation of specific heats with temperature

(ii) Dissociation of the combustion products

(iii) Progressive combustion

(iv) Incomplete combustion of fuel

(v) Heat transfer into the walls of the combustion chamber

(vi) Blowdown at the end of the exhaust process

(vii) Gas exchange process

An estimate of these losses can be made from previous experience and some
simple tests on the engines and these estimates can be used in evaluating the
performance of an engine.

4.2 COMPARISON OF AIR-STANDARD AND ACTUAL CYCLES

The actual cycles for internal combustion engines differ from air-standard
cycles in many respects. These differences are mainly due to:

(i) The working substance being a mixture of air and fuel vapour or finely
atomized liquid fuel in air combined with the products of combustion
left from the previous cycle.

(ii) The change in chemical composition of the working substance.

(iii) The variation of specific heats with temperature.

(iv) The change in the composition, temperature and actual amount of fresh
charge because of the residual gases.

(v) The progressive combustion rather than the instantaneous combustion.