Finite Element Results Página 1 de 9

Tabular Results
Results were generated with the finite element program FE/Pipe®. Stress results are post-processed in accordance with the rules specified in ASME Section III and ASME Section
VIII, Division 2.

Analysis Time Stamp: Wed Sep 25 16:15:29 2024.

Model Notes

Load Case Report

Solution Data

ASME Code Stress Output Plots

Stress Results - Notes

ASME Overstressed Areas

Highest Primary Stress Ratios

Highest Secondary Stress Ratios

Highest Fatigue Stress Ratios

Stress Intensification Factors

Allowable Loads

Flexibilities

Graphical Results

Model Notes
Model Notes

Input Echo:

Model Type : Cylindrical Shell

Parent Geometry
Parent Outside Diam. : 812.800 mm.
Thickness : 7.925 mm.
Fillet Along Shell : 9.000 mm.

Parent Properties:
Cold Allowable : 137.9 MPa
Hot Allowable : 137.9 MPa
Material DB # 1016422.
Ultimate Tensile (Amb) : 482.6 MPa
Yield Strength (Amb) : 262.0 MPa
Yield Strength (Hot) : 246.2 MPa
Elastic Modulus (Amb) : 202720.0 MPa
Poissons Ratio : 0.300
Expansion Coefficient : 0.1188E-04 mm./mm./deg.
Weight Density : 0.0000E+00 N /cu.mm.(NOT USED)

Nozzle Geometry
Nozzle Outside Diam. : 457.200 mm.
Thickness : 6.730 mm.
Length : 432.000 mm.
Nozzle Weld Length : 9.000 mm.
RePad Width : 121.000 mm.
RePad Thickness : 9.525 mm.
RePad Weld Leg : 9.000 mm.
Nozzle Tilt Angle : 0.000 deg.
Distance from Top : 524.000 mm.
Distance from Bottom : 776.000 mm.

Nozzle Properties
Cold Allowable : 117.9 MPa
Hot Allowable : 117.9 MPa
Material DB # 1009922.
Ultimate Tensile (Amb) : 413.7 MPa
Yield Strength (Amb) : 241.3 MPa
Yield Strength (Hot) : 226.8 MPa
Elastic Modulus (Amb) : 202720.0 MPa
Poissons Ratio : 0.300
Expansion Coefficient : 0.1188E-04 mm./mm./deg.
Weight Density : 0.0000E+00 N /cu.mm. (NOT USED)

Design Operating Cycles : 7000.

Ambient Temperature (Deg.) : 21.10

Uniform thermal expansion produces no stress in this geometry.

Any thermal loads will come through operating forces and
moments applied through the nozzle.

Nozzle Inside Temperature : 65.00 deg.

Nozzle Outside Temperature : 65.00 deg.
Vessel Inside Temperature : 65.00 deg.
Vessel Outside Temperature : 65.00 deg.

Nozzle Pressure : 1.844 MPa

Vessel Pressure : 1.844 MPa

Operating Pressure : 1.0 MPa

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 2 de 9

The operating pressure is used for secondary and peak stress

cases. The design pressure is used for primary cases. The ratio
of the operating/design pressure = 0.531

User Defined Load Input Echo:

Loads are given at the End of Nozzle
Loads are defined in Local Coordinates

Forces( N ) Moments (N-m)

Load Case FX FY FZ MX MY MZ
---------------------------------------------------------------------------
WEIGHT: 13524.0 39433.0 8522.0 11924.0 22683.0 13045.0

FEA Model Loads:

These are the actual loads applied to the FEA model.
These are the User Defined Loads translated to the
end of the nozzle and reported in global coordinates.

Forces( N ) Moments (N-m)

Load Case FX FY FZ MX MY MZ
---------------------------------------------------------------------------
WEIGHT: 13524.0 39433.0 8522.0 11924.0 22683.0 13045.0

The "top" or "positive" end of this model is "free" in

the axial and translational directions.

Stresses ARE nodally AVERAGED.

Vessel Centerline Vector : 0.000 1.000 0.000

Nozzle Orientation Vector : 1.000 0.000 0.000

Table of Contents

Load Case Report

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:12pm SEP 25,2024

Load Case Report $X

Inner and outer element temperatures are the same

throughout the model. No thermal ratcheting
calculations will be performed.

THE 9 LOAD CASES ANALYZED ARE:

1 WEIGHT ONLY (Wgt Only)

Weight ONLY case run to get the stress range

between the installed and the operating states.

/-------- Loads in Case 1

Loads due to Weight

2 SUSTAINED (Wgt+Pr)

Sustained case run to satisfy local primary

membrane and bending stress limits.

/-------- Loads in Case 2

Loads due to Weight
Pressure Case 1

3 OPERATING

Case run to compute the operating stresses used in

secondary, peak and range calculations as needed.

/-------- Loads in Case 3

Pressure Case 1
Loads from (Operating)

4 RANGE (Fatigue Calc Performed)

Case run to get the RANGE of stresses.

as described in NB-3222.2, 5.5.3.2, 5.5.5.2 or 5.5.6.1.

/-------- Combinations in Range Case 4

Plus Stress Results from CASE 3
Minus Stress Results from CASE 1

5 Program Generated -- Force Only

Case run to compute sif's and flexibilities.

/-------- Loads in Case 5
Loads from (Axial)

6 Program Generated -- Force Only

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 3 de 9

Case run to compute sif's and flexibilities.

/-------- Loads in Case 6
Loads from (Inplane)

7 Program Generated -- Force Only

Case run to compute sif's and flexibilities.

/-------- Loads in Case 7
Loads from (Outplane)

8 Program Generated -- Force Only

Case run to compute sif's and flexibilities.

/-------- Loads in Case 8
Loads from (Torsion)

9 Program Generated -- Force Only

Case run to compute sif's and flexibilities.

/-------- Loads in Case 9
Pressure Case 1

Table of Contents

Solution Data
FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:12pm SEP 25,2024

Solution Data

Maximum Solution Row Size = 1032

Number of Nodes = 3748
Number of Elements = 1236
Number of Solution Cases = 8

Summation of Loads per Case

Case # FX FY FZ

1 13520. 39430. 8522.

2 4803. 977809. 8522.
3 -8717. 938379. 0.
4 1313354. 0. 0.
5 0. 2. 0.
6 0. 0. -2.
7 0. 0. 0.
8 -8717. 938379. 0.

Table of Contents

ASME Code Stress Output Plots

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

ASME Code Stress Output Plots $X

1) Pl < SPL (SUS,Membrane) Case 2

2) Qb < SPS (SUS,Bending) Case 2

3) Pl+Pb+Q < SPS (SUS,Inside) Case 2

4) Pl+Pb+Q < SPS (SUS,Outside) Case 2

5) S1+S2+S3 < 4S (SUS,S1+S2+S3) Case 2

6) Pl+Pb+Q < SPS (OPE,Inside) Case 3

7) Pl+Pb+Q < SPS (OPE,Outside) Case 3

8) Membrane < User (OPE,Membrane) Case 3

9) Bending < User (OPE,Bending) Case 3

10) S1+S2+S3 < 4S (OPE,S1+S2+S3) Case 3

11) Pl+Pb+Q+F < Sa (SIF,Outside) Case 5

12) Pl+Pb+Q+F < Sa (SIF,Outside) Case 6

13) Pl+Pb+Q+F < Sa (SIF,Outside) Case 7

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 4 de 9

14) Pl+Pb+Q+F < Sa (SIF,Outside) Case 8

15) Pl+Pb+Q+F < Sa (SIF,Outside) Case 9

16) Pl+Pb+Q < SPS (EXP,Inside) Case 4

17) Pl+Pb+Q < SPS (EXP,Outside) Case 4

18) Pl+Pb+Q+F < Sa (EXP,Inside) Case 4

19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

Table of Contents

Stress Results - Notes

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Stress Results - Notes

- Results in this analysis were generated using the finite

element solution method.

- Using 2013-2017 ASME Section VIII Division 2

- Use Polished Bar fatigue curve.

- Ratio between Operating and Design Pressure = 0.5314534

Range cases use operating pressure. Primary cases
use design pressure.

- Assume free end displacements of attached pipe

(e.g. thermal loads) are secondary loads.

- Use Equivalent Stress (Von Mises).

- TRIAXIAL Stress Guidelines:

Include S1+S2+S3 evaluation for operating stress.
Include S1+S2+S3 evaluation in primary case evaluation.
Bending stress NOT included for all S1+S2+S3 calculations.

- Use local tensor values for averaged and not averaged stresses.

Table of Contents

ASME Overstressed Areas

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

ASME Overstressed Areas $X

*** NO OVERSTRESSED NODES IN THIS MODEL ***

Table of Contents

Highest Primary Stress Ratios

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Highest Primary Stress Ratios $X

Pad/Header at Junction

Pl SPL Primary Membrane Load Case 2

166 246 Plot Reference:
MPa MPa 1) Pl < SPL (SUS,Membrane) Case 2

67%

Branch at Junction

Pl SPL Primary Membrane Load Case 2

218 227 Plot Reference:

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 5 de 9

MPa MPa 1) Pl < SPL (SUS,Membrane) Case 2

96%

Branch Transition

Pl SPL Primary Membrane Load Case 2

88 227 Plot Reference:
MPa MPa 1) Pl < SPL (SUS,Membrane) Case 2

38%

Pad Outer Edge Weld

Pl+Pb+Q SPS Primary+Secondary (Outer) Load Case 2

272 508 Plot Reference:
MPa MPa 4) Pl+Pb+Q < SPS (SUS,Outside) Case 2

53%

Header Outside Pad Area

Pl SPL Primary Membrane Load Case 2

104 246 Plot Reference:
MPa MPa 1) Pl < SPL (SUS,Membrane) Case 2

42%

Branch removed from Junction

Pl SPL Primary Membrane Load Case 2

99 227 Plot Reference:
MPa MPa 1) Pl < SPL (SUS,Membrane) Case 2

43%

Table of Contents

Highest Secondary Stress Ratios

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Highest Secondary Stress Ratios $X

Pad/Header at Junction

Pl+Pb+Q SPS Primary+Secondary (Outer) Load Case 2

189 508 Plot Reference:
MPa MPa 4) Pl+Pb+Q < SPS (SUS,Outside) Case 2

37%

Branch at Junction

Pl+Pb+Q SPS Primary+Secondary (Outer) Load Case 2

423 468 Plot Reference:
MPa MPa 4) Pl+Pb+Q < SPS (SUS,Outside) Case 2

90%

Branch Transition

Pl+Pb+Q SPS Primary+Secondary (Inner) Load Case 2

116 468 Plot Reference:
MPa MPa 3) Pl+Pb+Q < SPS (SUS,Inside) Case 2

24%

Pad Outer Edge Weld

Pl+Pb+Q SPS Primary+Secondary (Outer) Load Case 2

272 508 Plot Reference:
MPa MPa 4) Pl+Pb+Q < SPS (SUS,Outside) Case 2

53%

Header Outside Pad Area

Pl+Pb+Q SPS Primary+Secondary (Inner) Load Case 2

146 508 Plot Reference:
MPa MPa 3) Pl+Pb+Q < SPS (SUS,Inside) Case 2

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 6 de 9

28%

Branch removed from Junction

Pl+Pb+Q SPS Primary+Secondary (Inner) Load Case 2

128 468 Plot Reference:
MPa MPa 3) Pl+Pb+Q < SPS (SUS,Inside) Case 2

27%

Table of Contents

Highest Fatigue Stress Ratios

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Highest Fatigue Stress Ratios $X

Pad/Header at Junction

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Outer) Load Case 4

93 0.015 Life Stress Concentration Factor = 1.350
MPa 0.321 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 458,170.
Allowable "B31" Fatigue Stress Allowable = 344.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 1,521,197.
WRC 474 99% Probability Cycles = 353,388.
32% WRC 474 95% Probability Cycles = 490,635.
BS5500 Allowed Cycles(Curve F) = 263,155.
Membrane-to-Bending Ratio = 1.640
Bending-to-PL+PB+Q Ratio = 0.379
Plot Reference:
19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

Branch at Junction

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Outer) Load Case 4

263 0.747 Life Stress Concentration Factor = 1.350
MPa 0.906 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 9,375.
Allowable "B31" Fatigue Stress Allowable = 294.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 133,174.
WRC 474 99% Probability Cycles = 30,938.
90% WRC 474 95% Probability Cycles = 42,953.
BS5500 Allowed Cycles(Curve F) = 11,707.
Membrane-to-Bending Ratio = 0.300
Bending-to-PL+PB+Q Ratio = 0.769
Plot Reference:
19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

Branch Transition

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Outer) Load Case 4

36 0.000 Life Stress Concentration Factor = 1.000
MPa 0.123 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 1.0000E11
Allowable "B31" Fatigue Stress Allowable = 294.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 22,388,484.
WRC 474 99% Probability Cycles = 5,201,042.
12% WRC 474 95% Probability Cycles = 7,220,994.
BS5500 Allowed Cycles(Curve F) = 1,919,909.
Membrane-to-Bending Ratio = 11.576
Bending-to-PL+PB+Q Ratio = 0.080
Plot Reference:
19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

Pad Outer Edge Weld

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Outer) Load Case 4

119 0.044 Life Stress Concentration Factor = 1.350
MPa 0.410 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 159,889.
Allowable "B31" Fatigue Stress Allowable = 344.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 1,297,771.
WRC 474 99% Probability Cycles = 301,484.
40% WRC 474 95% Probability Cycles = 418,572.
BS5500 Allowed Cycles(Curve F) = 126,693.
Membrane-to-Bending Ratio = 0.506
Bending-to-PL+PB+Q Ratio = 0.664
Plot Reference:
19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 7 de 9

Header Outside Pad Area

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Outer) Load Case 4

48 0.000 Life Stress Concentration Factor = 1.000
MPa 0.167 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 6.5644E10
Allowable "B31" Fatigue Stress Allowable = 344.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 8,019,228.
WRC 474 99% Probability Cycles = 1,862,939.
16% WRC 474 95% Probability Cycles = 2,586,457.
BS5500 Allowed Cycles(Curve F) = 760,394.
Membrane-to-Bending Ratio = 1.045
Bending-to-PL+PB+Q Ratio = 0.489
Plot Reference:
19) Pl+Pb+Q+F < Sa (EXP,Outside) Case 4

Branch removed from Junction

Pl+Pb+Q+F Damage Ratio Primary+Secondary+Peak (Inner) Load Case 4

47 0.000 Life Stress Concentration Factor = 1.000
MPa 0.164 Stress Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 9.5999E10
Allowable "B31" Fatigue Stress Allowable = 294.8
289.9 Markl Fatigue Stress Allowable = 287.5
MPa WRC 474 Mean Cycles to Failure = 9,357,571.
WRC 474 99% Probability Cycles = 2,173,848.
16% WRC 474 95% Probability Cycles = 3,018,115.
BS5500 Allowed Cycles(Curve F) = 807,331.
Membrane-to-Bending Ratio = 1.786
Bending-to-PL+PB+Q Ratio = 0.359
Plot Reference:
18) Pl+Pb+Q+F < Sa (EXP,Inside) Case 4

Table of Contents

Stress Intensification Factors

FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Stress Intensification Factors $X

Branch/Nozzle Sif Summary

Peak Primary Secondary SSI

Axial : 8.870 6.570 13.140 1.652
Inplane : 3.717 2.753 5.507 1.548
Outplane: 10.509 7.784 15.569 1.718
Torsion : 0.789 1.064 1.168 0.888
Pressure: 1.823 1.618 2.701 1.148

The above stress intensification factors are to be used

in a beam-type analysis of the piping system. Inplane,
Outplane and Torsional sif's should be used with the
matching branch pipe whose diameter and thickness is given
below. The axial sif should be used to intensify the
axial stress in the branch pipe calculated by F/A. The
pressure sif should be used to intensify the nominal
pressure stress in the PARENT or HEADER, calculated
from PDo/2T. B31 calculations use mean diameters and
Section VIII calculations use outside diameters. SSIs are
based on peak stress factors and correlated test results.

Pipe OD : 457.200 mm.

Pipe Thk: 6.730 mm.
Z approx: 1072596.375 cu.mm.
Z exact : 1057043.750 cu.mm.

(SSI = SIF^x) Axial Inpl Outpl Tors Pres

SIF/SSI Exponents: 0.863 0.771 0.872 -0.261 0.801

SIF/SSI exponent based on relationship between primary and

peak stress factors from the finite element analysis.

B31.3 Branch Pressure i-factor = 5.588

Header Pressure i-factor = 3.683

The B31.3 pressure i-factors should be used with with

F/A, where F is the axial force due to pressure, and
A is the area of the pipe wall. This is equivalent to
finding the pressure stress from (ip)(PD/4T).

B31.3 (Branch)
Peak Stress Sif .... 0.000 Axial
3.800 Inplane
4.784 Outplane
1.000 Torsional
B31.1 (Branch)

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 8 de 9

Peak Stress Sif .... 0.000 Axial

4.784 Inplane
4.784 Outplane
4.784 Torsional
WRC 330 (Branch)
Peak Stress Sif .... 0.000 Axial
5.633 Inplane
4.784 Outplane
5.633 Torsional

Table of Contents

Allowable Loads
FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Allowable Loads $X

SECONDARY Maximum Conservative Realistic

Load Type (Range): Individual Simultaneous Simultaneous
Occuring Occuring Occuring
Axial Force ( N ) 311380. 53456. 80185.
Inplane Moment (mm. N ) 82462544. 10010384. 21235230.
Outplane Moment (mm. N ) 29167500. 3540734. 7511030.
Torsional Moment (mm. N ) 388633792. 52520324. 78780488.
Pressure (MPa ) 3.10 1.84 1.84

PRIMARY Maximum Conservative Realistic

Load Type: Individual Simultaneous Simultaneous
Occuring Occuring Occuring
Axial Force ( N ) 328777. 35652. 53477.
Inplane Moment (mm. N ) 87069832. 6676204. 14162366.
Outplane Moment (mm. N ) 30797128. 2361414. 5009314.
Torsional Moment (mm. N ) 225318256. 24432800. 36649200.
Pressure (MPa ) 2.73 1.84 1.84

NOTES:

1) Maximum Individual Occuring Loads are the maximum

allowed values of the respective loads if all other
load components are zero, i.e. the listed axial force
may be applied if the inplane, outplane and torsional
moments, and the pressure are zero.

2) The Conservative Allowable Simultaneous loads are

the maximum loads that can be applied simultaneously.
A conservative stress combination equation is used
that typically produces stresses within 50-70% of the
allowable stress.

3) The Realistic Allowable Simultaneous loads are the

maximum loads that can be applied simultaneously. A
more realistic stress combination equation is used
based on experience at Paulin Research. Stresses are
typically produced within 80-105% of the allowable.

4) Secondary allowable loads are limits for expansion

and operating piping loads.

5) Primary allowable loads are limits for weight,

primary and sustained type piping loads.

Table of Contents

Flexibilities
FEPipe Version 14.0 Jobname: NOZZLE $P
Released Mar 2019 4:15pm SEP 25,2024

Flexibilities $X

The following stiffnesses should be used in a piping,

"beam-type" analysis of the intersection. The stiff-
nesses should be inserted at the surface of the
branch/header or nozzle/vessel junction. The general
characteristics used for the branch pipe should be:

Outside Diameter = 457.200 mm.

Wall Thickness = 6.730 mm.

Axial Translational Stiffness = 557615. N /mm.

Inplane Rotational Stiffness = 535593088. mm. N /deg
Outplane Rotational Stiffness = 165968768. mm. N /deg

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Finite Element Results Página 9 de 9

Torsional Rotational Stiffness = 2511219712. mm. N /deg

Intersection Flexibility Factors for Branch/Nozzle :

Find axial stiffness: K = 3EI/(kd)^3 N /mm.

Find bending and torsional stiffnesses: K = EI/(kd) mm. N per radian.
The EI product is 0.49053E+14 N mm.^2
The value of (d) to use is: 450.470 mm..
The resulting bending stiffness is in units of force x length per radian.

Axial Flexibility Factor (k) = 1.424

Inplane Flexibility Factor (k) = 3.548
Outplane Flexibility Factor (k) = 11.451
Torsional Flexibility Factor (k) = 0.757

Table of Contents

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

 Página 1 de 1

Finite Element Model

Finite Element Model

1) Pl < SPL (SUS Membrane) Case 2

2) Qb < SPS (SUS Bending) Case 2

3) Pl+Pb+Q < SPS (SUS Inside) Case 2

4) Pl+Pb+Q < SPS (SUS Outside) Case 2

5) S1+S2+S3 < 4S (SUS S1+S2+S3) Case 2

6) Pl+Pb+Q < SPS (OPE Inside) Case 3

7) Pl+Pb+Q < SPS (OPE Outside) Case 3

8) Membrane < User (OPE Membrane) Case 3

9) Bending < User (OPE Bending) Case 3

10) S1+S2+S3 < 4S (OPE S1+S2+S3) Case 3

16) Pl+Pb+Q < SPS (EXP Inside) Case 4

17) Pl+Pb+Q < SPS (EXP Outside) Case 4

18) Pl+Pb+Q+F < Sa (EXP Inside) Case 4

19) Pl+Pb+Q+F < Sa (EXP Outside) Case 4

11) Pl+Pb+Q+F < Sa (SIF Outside) Case 5

12) Pl+Pb+Q+F < Sa (SIF Outside) Case 6

13) Pl+Pb+Q+F < Sa (SIF Outside) Case 7

14) Pl+Pb+Q+F < Sa (SIF Outside) Case 8

15) Pl+Pb+Q+F < Sa (SIF Outside) Case 9

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 1 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 2 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 3 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 4 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 5 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 6 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 7 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 8 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 9 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024

Graphical Results Página 10 de 10

file://E:\Trabajo\Filtros ODV (16-9-24)\24-09-2024\Filtro Canasto\OUTPUT\NOZZL... 25/09/2024