"EESFTT
(BO[IPV
&DPOPNJD
%FWFMPQNFOU
"SFB
+JBOHYJ

$IJOB

1PTUDPEF


5FMF


'BY


&NBJM
FYQPSU!BDIUFDLUPPMDPN
8FCTJUF
XXXBDIUFDLUPPMDPN
 Grooving

Parting Off-Grooving Series

CS: Double-edged inserts applicable to parting off and grooving

7°
H
R

Cutting parameter Dimension(mm) Grade

Inserts Product code

AW100K
AP301U
Feed
Tmax W R L H h
(mm/rev)

ACD 202-CS 19.7 0.04-0.13 2 0.2 20 1.7 5.1 ●

ACD 302-CS 19.7 0.05-0.15 3 0.2 20 2.4 5.1 ●

Marked：● Stock available ○ Non-stocked standard

P103 P134

124
Grooving

Parting Off-Grooving Series

CM: Double-edged, single-edged inserts applicable to parting off and grooving

ACD ACS

h h

7° 7°

R
H R H

W W

Cutting parameter Dimension(mm) Grade

Grooving inserts
Inserts Product code

AW100K
AP301U
Feed
Tmax W R L H h
(mm/rev)

ACD 202-CM 19.7 0.04-0.15 2 0.2 20.0 1.7 5.1 ●

ACD 202-CM-6R 19.7 0.03-0.09 2 0.2 20.7 1.7 5.1 ●

ACD 202-CM-6L 19.7 0.03-0.09 2 0.2 20.7 1.7 5.1 ●

ACD 202-CM-15R 19.7 0.03-0.09 2 0.2 21.0 1.7 5.1 ●

ACD 202-CM-15L 19.7 0.03-0.09 2 0.2 21.0 1.7 5.1 ●

ACD 302-CM 19.7 0.05-0.16 3 0.2 20.0 2.4 5.1 ●

ACD 302-CM-6R 19.7 0.04-0.14 3 0.2 20.7 2.4 5.1 ●

ACD 302-CM-6L 19.7 0.04-0.14 3 0.2 20.7 2.4 5.1 ●

ACD 302-CM-15R 19.7 0.04-0.14 3 0.2 21.0 2.4 5.1 ●

ACD 302-CM-15L 19.7 0.04-0.14 3 0.2 21.0 2.4 5.1 ●

ACD 403-CM 19.7 0.06-0.18 4 0.3 20.0 3.0 5.1 ●

ACD 403-CM-4R 19.7 0.05-0.16 4 0.3 20.7 3.0 5.1 ●

ACD 403-CM-4L 19.7 0.05-0.16 4 0.3 20.7 3.0 5.1 ●

ACD 503-CM 24.7 0.06-0.20 5 0.3 25.0 4.0 5.0 ●

ACD 503-CM-4R 24.7 0.06-0.18 5 0.3 25.7 4.0 5.0 ○

ACD 503-CM-4L 24.7 0.06-0.18 5 0.3 25.7 4.0 5.0 ○

ACD 603-CM 29.7 0.06-0.22 6 0.3 25.0 5.0 5.0 ●

ACS 202-CM 19.7 0.04-0.15 2 0.2 20.0 1.7 5.1 ●

ACS 302-CM 19.7 0.05-0.16 3 0.2 20.0 2.4 5.1 ●

ACS 403-CM 19.7 0.06-0.18 4 0.3 20.0 3.0 5.1 ○

ACS 503-CM 24.7 0.06-0.20 5 0.3 25.0 4.0 5.0 ○

ACS 603-CM 29.7 0.06-0.22 6 0.3 25.0 5.0 5.0 ○

Remark: 1. if R/L style inserts are selected, the feed need to be reduced by 20-40% Marked：● Stock available ○ Non-stocked standard
2. ACS single edged insert's Tmas is determined according to the tool holder.

P103 P134

125
 Grooving

Parting Off-Grooving Series

CH: Double-edged, single-edged inserts applicable to parting off and grooving

ACD ACS

h h

7° 7°
R
H R H

W
W

L
L

Cutting parameter Dimension(mm) Grade

inserts* Product code

AW100K
AP301U
Feed
Tmax W R L H h
(mm/rev)

ACD 202-CH 19.7 0.05-0.20 2 0.2 20.0 1.7 5.1 ●

ACD 202-CH-6R 19.7 0.04-0.16 2 0.2 20.7 1.7 5.1 ●

ACD 202-CH-6L 19.7 0.04-0.16 2 0.2 20.7 1.7 5.1 ●

ACD 202-CH-15R 19.7 0.04-0.15 2 0.2 21.0 1.7 5.1 ●

ACD 202-CH-15L 19.7 0.04-0.15 2 0.2 21.0 1.7 5.1 ●

ACD 302-CH 19.7 0.07-0.25 3 0.2 20.0 2.4 5.1 ●

ACD 302-CH-6R 20.7 0.05-0.20 3 0.2 20.7 2.4 5.1 ●

ACD 302-CH-6L 21.7 0.05-0.20 3 0.2 20.7 2.4 5.1 ●

ACD 302-CH-15R 20.0 0.05-0.18 3 0.2 21.0 2.4 5.1 ●

ACD 302-CH-15L 20.0 0.05-0.18 3 0.2 21.0 2.4 5.1 ●

ACD 403-CH 19.0 0.08-0.30 4 0.3 20.0 3.0 5.1 ●

ACD 403-CH-4R 19.7 0.06-0.25 4 0.3 20.7 3.0 5.1 ●

ACD 403-CH-4L 19.7 0.06-0.25 4 0.3 20.7 3.0 5.1 ●

ACD 503-CH 24.0 0.09-0.35 5 0.3 25.0 4.0 5.0 ●

ACD 503-CH-4R 24.7 0.08-0.30 5 0.3 25.7 4.0 5.0 ●

ACD 503-CH-4L 25.7 0.08-0.30 5 0.3 25.7 4.0 5.0 ●

ACD 603-CH 24.0 0.12-0.40 6 0.3 25.0 5.0 5.0 ●

ACD 804-CH 29.0 0.15-0.45 8 0.4 30.0 6.0 6.1 ●

ACS 202-CH - 0.05-0.20 2 0.2 20.0 1.7 5.1 ●

ACS 302-CH - 0.07-0.25 3 0.2 20.0 2.4 5.1 ●

ACS 403-CH - 0.08-0.30 4 0.3 20.0 3.0 5.1 ●

ACS 503-CH - 0.09-0.35 5 0.3 20.0 4.0 5.0 ●

ACS 603-CH - 0.12-0.40 6 0.3 25.0 5.0 5.0 ○

Remark: 1. if R/L style inserts are selected, the feed need to be reduced by 20-40% Marked：● Stock available ○ Non-stocked standard
2. ACS single edged insert's Tmas is determined according to the tool holder.

P103 P134

126
Grooving

Grooving-Turning Series

TS: Double-edged inserts applicable to external, internal

and face turning, grooving and parting off
h

7°

H R

Cutting parameter Dimension(mm) Grade

Grooving inserts
Grooving Turning
inserts* Product code

AW100K
AP301U
Feed Tmax Feed Ap W R L H h
(mm/rev) (mm/rev) (mm)

ATD 203-TS 0.04-0.20 19.7 0.12-0.19 0.40-1.50 2 0.3 20.7 1.7 5.1 ●

ATD 303-TS 0.05-0.25 19.7 0.15-0.23 0.45-2.00 3 0.3 20.7 2.2 5.1 ●

ATD 404-TS 0.06-0.27 19.7 0.18-0.25 0.50-2.50 4 0.4 20.7 3.0 5.1 ●

ATD 408-TS 0.06-0.27 19.7 0.18-0.25 1.00-2.50 4 0.8 20.7 3.0 5.1 ●

ATD 504-TS 0.07-0.30 24.7 0.20-0.30 0.55-3.50 5 0.4 25.7 4.0 5.0 ●

ATD 508-TS 0.07-0.30 24.7 0.20-0.30 1.00-3.50 5 0.8 25.7 4.0 5.0 ●

ATD 604-TS 0.10-0.40 24.7 0.22-0.45 0.65-3.80 6 0.4 25.7 5.0 5.0 ●

ATD 608-TS 0.10-0.40 24.7 0.22-0.45 1.00-3.80 6 0.8 25.7 5.0 5.0 ●

ATD 808-TS 0.12-0.45 30.5 0.28-0.50 1.00-4.50 8 0.8 31.5 6.0 6.1 ○

Marked：● Stock available ○ Non-stocked standard

P103 P134

127
 Grooving

Grooving-Turning Series

TM: Double-edged inserts applicable to external, internal and

face turning, grooving and parting off
h

7°
R
H

Cutting parameter Dimension(mm) Grade

Grooving Turning
inserts* Product code

AW100K
AP301U
Feed Tmax Feed Ap W R L H h
(mm/rev) (mm/rev) (mm)

ATD 304-TM 0.10-0.25 19.7 0.15-0.22 0.50-2.0 3 0.4 20.7 2.2 5.1 ●

ATD 404-TM 0.15-0.30 19.7 0.18-0.27 0.50-2.5 4 0.4 20.7 3.0 5.1 ●

ATD 408-TM 0.15-0.30 19.7 0.18-0.27 1.00-2.5 4 0.8 20.7 3.0 5.1 ●

ATD 504-TM 0.18-0.35 24.7 0.20-0.35 0.55-3.5 5 0.4 25.7 4.0 5.0 ●

ATD 508-TM 0.18-0.35 24.7 0.20-0.35 1.00-3.5 5 0.8 25.7 4.0 5.0 ●

ATD 604-TM 0.20-0.45 24.7 0.22-0.45 0.65-4.0 6 0.4 25.7 5.0 5.0 ●

ATD 608-TM 0.20-0.45 24.7 0.22-0.45 1.00-4.0 6 0.8 25.7 5.0 5.0 ●

ATD 808-TM 0.22-0.50 30.5 0.28-0.50 1.00-5.0 8 0.8 31.5 6.0 6.1 ○

ATD 812-TM 0.22-0.50 30.5 0.28-0.50 1.50-5.0 8 1.2 31.5 6.0 6.1 ●

Marked：● Stock available ○ Non-stocked standard

P103 P134

128
Grooving

Grooving-Turning Series

RM: Double-edged inserts applicable to external turning, grooving and profiling

7°
R
H

Cutting parameter Dimension(mm) Grade

Grooving inserts
Grooving Turning
inserts* Product code

AW100K
AP301U
Feed Feed Ap W R L H h
(mm/rev) (mm/rev) (mm)

ATD 210-RM 0.06-0.15 0.12-0.25 0.4-1.0 2 1.0 20.7 1.7 5.1 ●

ATD 315-RM 0.08-0.18 0.15-0.30 0.5-1.5 3 1.5 20.7 2.2 5.1 ●

ATD 420-RM 0.10-0.20 0.18-0.35 0.6-2.0 4 2.0 20.7 3.0 5.1 ●

ATD 525-RM 0.12-0.25 0.20-0.40 0.7-2.5 5 2.5 25.7 4.0 5.0 ●

ATD 630-RM 0.15-0.30 0.25-0.50 0.9-3.0 6 3.0 25.7 5.0 5.0 ●

ATD 840-RM 0.18-0.35 0.30-0.60 1.0-4.0 8 4.0 31.5 6.0 6.1 ●

Marked：● Stock available ○ Non-stocked standard

P103 P134

129
 Grooving

Grooving-Turning Series

RA: Double-edged ground inserts applicable to aluminium

wheel turning and profiling
h

10°

H R

W L

Cutting parameter Dimension(mm) Grade

Grooving Turning
inserts* Product code

AW100K
AP301U
Feed Feed Ap W R L H h
(mm/rev) (mm/rev) (mm)

ATD 315-RA 0.08-0.18 0.15-0.30 0.5-1.5 3 1.5 20.7 2.2 5.1 ○

ATD 420-RA 0.10-0.25 0.20-0.45 0.6-2.0 4 2.0 20.7 3.0 5.1 ○

ATD 525-RA 0.11-0.28 0.20-0.50 0.7-2.5 5 2.5 25.7 4.0 5.0 ○

ATD 630-RA 0.12-0.30 0.22-0.60 0.9-3.0 6 3.0 25.7 5.0 5.0 ○

ATD 840-RA 0.15-0.40 0.25-0.65 1.0-4.0 8 4.0 31.5 6.0 6.1 ○

Marked：● Stock available ○ Non-stocked standard

P103 P134

130
Grooving

Grooving Series

Ground inserts applicable to grooving

h

7°

Tmax H R

Cutting parameter Dimension(mm) Grade

Grooving inserts
Suitable Grooving
inserts* Product code tool

AW100K
AP301U
holder Feed W R Tmax H h L
(mm/rev)

ATD 100E000G 2mm 0.02-0.05 1.00 0.00 2.00 2.20 5.1 20.700 ●

ATD 104E000G 2mm 0.02-0.05 1.04 0.00 2.00 2.20 5.1 20.700 ●

*ATD 115E000G 2mm 0.02-0.05 1.15 0.00 2.00 2.20 5.1 20.700 ●

ATD 120E000G 2mm 0.03-0.05 1.20 0.00 2.00 2.20 5.1 20.700 ●

ATD 125E010G 2mm 0.03-0.05 1.25 0.10 2.00 2.20 5.1 20.700 ●

*ATD 130E000G 2mm 0.03-0.05 1.30 0.00 2.00 2.20 5.1 20.700 ●

ATD 135E000G 2mm 0.03-0.05 1.35 0.00 2.00 2.20 5.1 20.700 ●

ATD 140E000G 2mm 0.03-0.06 1.40 0.00 2.00 2.20 5.1 20.700 ●

ATD 145E010G 2mm 0.03-0.06 1.45 0.10 2.00 2.20 5.1 20.700 ●

ATD 147E000G 2mm 0.03-0.06 1.47 0.00 2.50 2.20 5.1 20.700 ●

ATD 150E010G 2mm 0.03-0.06 1.50 0.10 2.50 2.20 5.1 20.700 ●

ATD 157E015G 2mm 0.03-0.07 1.57 0.15 2.70 2.20 5.1 20.700 ●

*ATD 165E010G 2mm 0.03-0.07 1.65 0.10 2.70 2.20 5.1 20.700 ●

ATD 170E010G 2mm 0.03-0.07 1.70 0.10 3.00 2.20 5.1 20.700 ●

ATD 178E018G 2mm 0.03-0.07 1.78 0.18 3.00 2.20 5.1 20.700 ●

*ATD 190E010G 2mm 0.04-0.09 1.90 0.10 3.00 2.20 5.1 20.700 ●

ATD 196E015G 2mm 0.04-0.09 1.96 0.15 3.00 2.20 5.1 20.700 ●

ATD 200E020G 2mm 0.04-0.09 2.00 0.20 3.00 2.20 5.1 20.700 ●

*ATD 215E010G 2mm 0.04-0.10 2.15 0.10 3.00 2.20 5.1 20.700 ●

ATD 222E015G 2mm 0.04-0.10 2.22 0.15 3.50 2.20 5.1 20.700 ●

ATD 230E020G 2mm 0.04-0.10 2.30 0.20 3.50 2.20 5.1 20.700 ●

ATD 100E050G 2mm 0.03-0.06 1.00 0.50 2.00 2.20 5.1 20.700 ●

ATD 140E070G 2mm 0.04-0.07 1.40 0.70 2.00 2.20 5.1 20.700 ●

ATD 157E079G 2mm 0.04-0.08 1.57 0.78 2.70 2.20 5.1 20.700 ●

ATD 200E100G 2mm 0.05-0.11 2.00 1.00 3.00 2.20 5.1 20.700 ●

ATD 239E120G 2mm 0.06-0.12 2.39 1.19 - 2.20 5.1 20.700 ●

1. * For circlap grooves Marked：● Stock available ○ Non-stocked standard

2.When the width of the insert is less than 1.78mm, please pay attention to size A of the holder

P103 P134

131
 Grooving

Grooving Series

Ground inserts applicable to profiling, turning and grooving

7°

Tmax R
H

Cutting parameter Dimension(mm) Grade

Suitable Grooving Turning

inserts* Product code tool

AW100K
AP301U
holder Feed Feed Ap W R Tmax H h L
(mm/rev) (mm/rev) (mm)

ATD 265E015 3mm 0.04-0.12 0.10-0.18 0.20-1.80 2.65 0.15 - 2.20 5.1 20.70 ●

ATD 300E020 3mm 0.06-0.14 0.11-0.20 0.30-2.00 3.00 0.20 - 2.20 5.1 20.70 ●

ATD 300E040 3mm 0.06-0.15 0.15-0.23 0.50-2.20 3.00 0.40 - 2.20 5.1 20.70 ●

ATD 400E040 4mm 0.08-0.19 0.16-0.30 0.50-2.50 4.00 0.40 - 3.00 5.1 20.70 ●

ATD 400E080 4mm 0.08-0.19 0.16-0.30 1.00-2.50 4.00 0.80 - 3.00 5.1 20.70 ●

ATD 415E015 4mm 0.08-0.19 0.16-0.30 0.20-2.50 4.15 0.15 - 3.00 5.1 20.70 ●

ATD 478E055 5mm 0.10-0.20 0.20-0.35 0.60-2.60 4.78 0.55 - 4.00 5.0 25.70 ●

ATD 500E040 5mm 0.10-0.20 0.20-0.35 0.50-2.60 5.00 0.40 - 4.00 5.0 25.70 ●

ATD 500E080 5mm 0.10-0.20 0.22-0.35 1.00-3.00 5.00 0.80 - 4.00 5.0 25.70 ●

ATD 515E015 5mm 0.10-0.22 0.22-0.35 0.20-3.00 5.15 0.15 - 4.00 5.0 25.70 ●

ATD 555E055 6mm 0.12-0.28 0.23-0.40 0.60-3.00 5.55 0.55 - 5.00 5.0 25.70 ●

ATD 600E080 6mm 0.12-0.30 0.25-0.45 1.00-3.50 6.00 0.80 - 5.00 5.0 25.70 ●

ATD 600E120 6mm 0.12-0.30 0.25-0.45 1.30-3.50 6.00 1.20 - 5.00 5.0 25.70 ●

ATD 635E080 6mm 0.13-0.30 0.25-0.45 1.00-3.50 6.35 0.80 - 5.00 5.0 25.70 ●

ATD 800E080 8mm 0.15-0.40 0.30-0.55 1.00-4.80 8.00 0.80 - 6.00 6.1 31.50 ●

ATD 800E120 8mm 0.15-0.40 0.30-0.55 1.20-4.80 8.00 1.20 - 6.00 6.1 31.50 ●

Marked：● Stock available ○ Non-stocked standard

P103 P134

132
Grooving

Grooving Series

Ground inserts applicable to turning and grooving

7°
H R

Cutting parameter Dimension(mm) Grade

Grooving inserts
Suitable Grooving Turning
inserts* Product code tool

AW100K
AP301U
holder Feed Feed Ap W R Tmax H h L
(mm/rev) (mm/rev) (mm)

ATD 300E150 3mm 0.08-0.19 0.15-0.30 0-1.50 3.00 1.50 - 2.20 5.1 20.700 ●

ATD 400E200 4mm 0.10-0.20 0.18-0.35 0-2.00 4.00 2.00 - 3.00 5.1 20.700 ●

ATD 478E239 5mm 0.12-0.24 0.22-0.45 0-2.40 4.78 2.39 - 4.00 5.0 25.700 ●

ATD 500E250 5mm 0.12-0.24 0.22-0.45 0-2.50 5.00 2.50 - 4.00 5.0 25.700 ●

ATD 600E300 6mm 0.15-0.30 0.25-0.50 0-3.00 6.00 3.00 - 5.00 5.0 25.700 ●

ATD 800E400 8mm 0.18-0.35 0.30-0.65 0-4.00 8.00 4.00 - 6.00 6.1 31.500 ●

Marked：● Stock available ○ Non-stocked standard

P103 P134

133
 Milling

Milling Cutter Denomination System

A FM 90 -
080 -
Z07 -
A 22 R -
SN12 -
C
1 2 3 4 5 6 7 8 9 10

1. A--ACHTECK

2. Machining method 6. Connection

A Arbor
Face milling FM
W Weldon shank
Shoulder milling SM C Cylinder shank
N Whistle notch shank
Profile milling PM M Screw clamped with modular head

High feed milling HM

Side & face milling DM

Thread milling TM 7. Coupling Size

Chamfer milling CM 22——Connection diameter 22mm

3. Approach angle (Kr) 8. Direction of tool

Figure Angle R Right
90 90° L Left
88 88° N Neutral
75 75°
60 60°
45 45°
42 42°
● ●

● ● 9. Insert info
● ●
SN12——SN12 series insert
15 15
00 Round insert

10. Others
4. Cutter dia.
C Internal coolant
025 25mm
No mark No coolant
080 80mm
● ●

● ●

250 250mm

5. Number of teeth
Z02 2 teeth
● ●

Z05 5 teeth
● ●

Z30 30 teeth

138
Milling

Porcupine Cutter Denomination

A PE 90 -
063 -
Z04 -
A 27 R -
L13 -
L56 -
F -
C
1 2 3 4 5 6 7 8 9 10 11 12

1. A--ACHTECK

2. Cutting method 6. Coupling

A Arbor
Porcupine cutter PE
W Weldon shank
Shoulder milling C Cylinder shank
SM
cutter
N Whistle notch shank
Profile milling cutter PM M Screw clamped with modular head

Milling cutters
High feed milling
HM
cutter
Side and face
DM
Milling cutter
Thread milling 7. Coupling size
TM
cutter
Chamfer milling 27——Connection diameter 27mm
CM
cutter
Face milling cutter FM

8. Direction of tool
3. Approach angle (Kr) R Right
Figure Angle L Left
90 90° N Neutral
88 88°
75 75°
60 60°
45 45°
9. Insert information
42 42°
● ● LN13——LN13 series insert
● ●

● ●

10. Max. cutting depth

4. Cutter dia. L30 30MM
L45 45MM
025 25mm
L56 56MM
063 63mm
080 80mm
● ●

250 250mm
11. Tool type
F Full teeth
H Half teeth

5. Number of teeth
Z02 2 teeth
Z04 4 teeth
10. Others
Z05 5 teeth
● ● C With internal coolant
Z30 30 teeth No indication Without internal coolant

139
 Milling

Overview of Milling Products

AFM42-OD04 AFM42-OD06 AFM40-ON05 AFM45-SD09 AFM75-SD09

Product family

Page P148 P150 P152 P154 P156

Approach angle 42° 42° 40° 45° 75°

Max.ap（mm） 3.5 4.5 3.5 5 6

Diameter range（mm） φ32-φ125 φ50-φ160 φ50-φ160 φ16-φ125 φ25-φ100

Insert type OD..0404.. OD..0605.. ON..0504.. SD..09T3.. SD..09T3..

Face milling ● ● ● ● ●

Shoulder milling

Slot milling

Ramping ● ● ● ●
Application

Helical
interpolate ● ●
milling

Plunging

Profile milling

Chamfer milling ● ● ●

Pocket milling ● ●

Remark: ● Recommended application

140
Milling

Overview of Milling Products

AFM90-SD09 AFM45-SD12 AFM75-SD12 AFM90-SD12 AFM45-SN12

Product family

Page P158 P160 P162 P164 P166

Approach angle 90° 45° 75° 90° 45°

Max.ap（mm） 6 7 8 9 6.5

Diameter range（mm） φ25-φ100 φ50-φ125 φ50-φ125 φ50-φ125 φ50-φ250

Insert type SD..09T3.. SD..1204.. SD..1204.. SD..1204.. SN..1206..

Face milling ● ● ● ● ●

Milling cutters
Shoulder milling

Slot milling

Ramping ● ●
Application

Helical
interpolate
milling

Plunging

Profile milling

Chamfer milling ●

Pocket milling

Remark: ● Recommended application

141
 Milling

Overview of Milling Products

AFM45-SN19 AFM75-SN12 AFM88-SN12 AFM45-XN07 AFM45-XN09(C)

Product family

Page P166 P168 P170 P172 P174

Approach angle 45° 75° 88° 45° 45°

Max.ap（mm） 11 8 10 4.4 6

Diameter range（mm） φ160-φ250 φ50-φ250 φ50-φ200 φ40-φ160 φ63-φ200

Insert type SN..1909.. SN..1206.. SN..1206.. XN..0705.. XN..0906..

Face milling ● ● ● ● ●

Shoulder milling

Slot milling

Ramping
Application

Helical
interpolate
milling

Plunging

Profile milling

Chamfer milling

Pocket milling

Remark: ● Recommended application

142
Milling

Overview of Milling Products

AFM45-XN09(W) AFF40-LN12 AFF40-LN15 ASM90-LN09 ASM90-LN13

Product family

Page P174 P176 P176 P178 P180

Approach angle 45° 40° 40° 90° 90°

Max.ap（mm） 6 0.5 0.5 8 12

Diameter range（mm） φ80-φ200 φ80-φ100 φ125-φ250 φ20-φ80 φ40-φ160

0N..0504.. 0N..0504..
Insert type XN..0906.. LNHU 0904.. LNHU 1306..
LN..1204.. LN..1504..

Face milling ● ● ● ● ●

Milling cutters
Shoulder milling ● ●

Slot milling ● ●

Ramping
Application

Helical
interpolate
milling

Plunging

Profile milling

Chamfer milling

Pocket milling

Remark: ● Recommended application

143
 Milling

Overview of Milling Products

ASM90-LN16 ASM90-WN08 ASM90-AP10 ASM90-AP17 APE90-LN09

Product family

Page P182 P184 P186 P188 P190

Approach angle 90° 90° 90° 90° 90°

Max.ap（mm） 15 7 8 16 48

Diameter range（mm） φ63-φ160 φ40-φ250 φ16-φ63 φ25-φ63 φ25-φ50

Insert type LNHU 1607.. WN..0806.. APKT 1003.. APKT 1705.. LNHU 0904..

Face milling ● ● ● ● ●

Shoulder milling ● ● ● ● ●

Slot milling ● ● ● ●

Ramping ● ●
Application

Helical
interpolate ● ●
milling

Plunging ● ●

Profile milling

Chamfer milling

Pocket milling ● ●

Remark: ● Recommended application

144
Milling

Overview of Milling Products

APE90-LN13 APM00-RP APM00-RO08 APM00-RO10 APM00-RO12

Product family

Page P192 P194 P196 P198 P200

Approach angle 90° - - - -

Max.ap（mm） 56 - 4 5 6

Diameter range（mm） φ40-φ80 φ16-φ20 φ16-φ25 φ25-φ50 φ32-φ80

Insert type LNHU 1306.. RPM 080/100.. RO.. 0803.. RO..10T3.. RO..1204..

Face milling ● ● ● ●

Milling cutters
Shoulder milling ●

Slot milling

Ramping ● ● ● ●
Application

Helical
interpolate ● ● ●
milling

Plunging

Profile milling ● ● ● ●

Chamfer milling

Pocket milling ● ● ● ●

Remark: ● Recommended application

145
 Milling

Overview of Milling Products

APM00-RO16 APM00-RO20 AHM20-LN06 AHM15-XD09 AHM15-XD12

Product family

Page P202 P204 P206-207 P208 P210

Approach angle - - 20° 15° 15°

Max.ap（mm） 8 10 1.0 1.5 2.5

Diameter range（mm） φ63-φ100 φ100-φ160 φ16-φ63 φ25-φ50 φ32-φ125

Insert type RO..1605.. RO..2006.. LN..0604.. XD..0904.. XD..1205..

Face milling ● ● ● ● ●

Shoulder milling

Slot milling ● ● ●

Ramping ● ● ● ● ●
Application

Helical
interpolate ● ● ● ● ●
milling

Plunging ● ● ●

Profile milling ● ●

Chamfer milling

Pocket milling ● ● ● ● ●

Remark: ● Recommended application

146
Milling cutters
 Milling

AFM42-OD04
42 °Approaching angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM42-032-Z03-M16R-OD04-C 32 M16 43 3.5 3 OD..0404

Product code D d1 L apmax Internal coolant Z Inserts

AFM42-032-Z03-W32R-OD04-C 32 32 120 3.5 3 OD..0404

Product code D d1 L apmax Internal coolant Z Inserts

AFM42-040-Z04-A16R-OD04-C 40 16 40 3.5 4

AFM42-050-Z05-A16R-OD04-C 50 16 40 3.5 5

AFM42-063-Z05-A22R-OD04-C 63 22 40 3.5 5

AFM42-063-Z06-A22R-OD04-C 63 22 40 3.5 6

AFM42-080-Z06-A27R-OD04-C 80 27 50 3.5 6
OD..0404
AFM42-080-Z08-A27R-OD04-C 80 27 50 3.5 8

AFM42-100-Z07-A32R-OD04-C 100 32 50 3.5 7

AFM42-100-Z08-A32R-OD04-C 100 32 50 3.5 8

AFM42-125-Z08-A40R-OD04-C 125 40 63 3.5 8

AFM42-125-Z10-A40R-OD04-C 125 40 63 3.5 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ32-125 3.5Nm

SP040112 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

148
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

ODET 0404APFN-FM2 - 1.2 ●

ODHT 0404APEN-MM3 - 1.2 ● ● ● ● ●

ODEW 0404APSR-HR2 - 1.2 ● ● ●

ODMW 040408EN-HR2 0.8 - ● ●

ODMT 040408EN-MM3 0.8 - ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

OD..0404
Geometry
Material Tensile strength Hardness ap HR2 MM3 FM2
ISO
classification (N/mm2) (HB) fz
（mm）
min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.12 0.32 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.30 0.10 0.28 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.08 0.25 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 3.50 0.15 0.35 0.12 0.32 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - 0.10 0.32
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
0.08 0.20 - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

149
 Milling

AFM42-OD06
42 ° Approaching angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM42-050-Z04-A16R-OD06-C 50 16 40 4.5 4

AFM42-063-Z05-A22R-OD06-C 63 22 40 4.5 5

AFM42-080-Z05-A27R-OD06-C 80 27 50 4.5 5

AFM42-080-Z06-A27R-OD06-C 80 27 50 4.5 6

AFM42-100-Z06-A32R-OD06-C 100 32 50 4.5 6 OD..0605

AFM42-100-Z07-A32R-OD06-C 100 32 50 4.5 7

AFM42-125-Z07-A40R-OD06-C 125 40 63 4.5 7

AFM42-125-Z08-A40R-OD06-C 125 40 63 4.5 8

AFM42-160-Z10-A40R-OD06 160 40 63 4.5 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-160 5.0Nm

SP04512043 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

150
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

ODET 0605APFN-FM2 - 1.6 ●

ODMT 060508EN-MM3 0.8 - ● ● ● ● ● ●

ODMT 060512EN-MM3 1.2 - ●

ODHT 0605APEN-MM3 - 1.6 ● ● ● ● ●

ODEW 0605APSR-HR2 - 1.6 ● ●

ODEW 0605APSN-HR2 - 1.6 ●

ODMW 060512EN-HR2 1.2 - ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

OD..0605
Geometry
Material Tensile strength Hardness ap HR2 MM3 FM2
ISO
classification ( N/mm2 ) (HB) fz
（mm）
min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.40 0.12 0.35 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.35 0.10 0.30 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.08 0.28 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 4.50 0.15 0.40 0.12 0.35 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - 0.10 0.35
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
0.10 0.25 - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

151
 Milling

AFM40-ON05
40° Approaching angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM40-050-Z04-A22R-ON05-N-C 50 22 40 3.5 4

AFM40-050-Z06-A22R-ON05-N-C 50 22 40 3.5 6

AFM40-063-Z05-A22R-ON05-N-C 63 22 40 3.5 5

AFM40-063-Z06-A22R-ON05-N-C 63 22 40 3.5 6

AFM40-063-Z08-A22R-ON05-N-C 63 22 40 3.5 8

AFM40-080-Z06-A27R-ON05-N-C 80 27 50 3.5 6

AFM40-080-Z08-A27R-ON05-N-C 80 27 50 3.5 8

AFM40-080-Z09-A27R-ON05-N-C 80 27 50 3.5 9 ON..0504

AFM40-100-Z07-A32R-ON05-N-C 100 32 50 3.5 7

AFM40-100-Z09-A32R-ON05-N-C 100 32 50 3.5 9

AFM40-100-Z11-A32R-ON05-N-C 100 32 50 3.5 11

AFM40-125-Z07-A40R-ON05-N-C 125 40 63 3.5 7

AFM40-125-Z09-A40R-ON05-N-C 125 40 63 3.5 9

AFM40-125-Z14-A40R-ON05-N-C 125 40 63 3.5 14

AFM40-160-Z10-A40R-ON05-N 160 40 63 3.5 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-160 4.0Nm

SP040090 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

152
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

ONHU 050408-MM3 0.8 - ●

ONMU 050408-MM4 0.8 - ● ● ● ● ●

ONHU 050408AEN-MM3 0.8 0.7 ● ● ●

ONHU 050408AEN-MM4 0.8 0.7 ● ● ●

ONHU 0504ZNR-MM3 0.8 1.4 ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

ON..0504
Geometry
Material Tensile strength Hardness ap MM3 MM4
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel
<950 <280

P 700-950 200-280 0.10 0.25 0.15 0.35

Alloyed steel 950-1200 280-355

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.08 0.20 0.10 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 3.50 0.10 0.25 0.15 0.35

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

153
 Milling

AFM45-SD09
45° Approaching angle face milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-016-Z02-W16R-SD09-C 16 16 90 25 5 2

AFM45-020-Z02-W20R-SD09-C 20 20 110 30 5 2
SD..09T3
AFM45-025-Z03-W25R-SD09-C 25 25 120 30 5 3

AFM45-032-Z03-W32R-SD09-C 32 32 120 35 5 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-032-Z04-A16R-SD09-C 32 16 40 - 5 4

AFM45-040-Z05-A16R-SD09-C 40 16 40 - 5 5

AFM45-050-Z05-A22R-SD09-C 50 22 40 - 5 5

AFM45-050-Z06-A22R-SD09-C 50 22 40 - 5 6

AFM45-063-Z05-A22R-SD09-C 63 22 40 - 5 5

AFM45-063-Z07-A22R-SD09-C 63 22 40 - 5 7 SD..09T3

AFM45-080-Z06-A27R-SD09-C 80 27 50 - 5 6

AFM45-080-Z09-A27R-SD09-C 80 27 50 - 5 9

AFM45-100-Z07-A32R-SD09-C 100 32 50 - 5 7

AFM45-100-Z11-A32R-SD09-C 100 32 50 - 5 11

AFM45-125-Z08-A40R-SD09-C 125 40 63 - 5 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ16-32
3.5Nm
ST040075 DT-T15

φ40-125 SP040090 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

154
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 09T304EN-MM3 0.4 - ● ● ● ●

SDMT 09T308EN-MM3 0.8 - ● ● ● ●

SDGT 09T3AEEN-MM4 - 1.4 ● ● ● ●

SDMW 09T308EN-HR2 0.8 - ● ●

SDHW 09T3AESN-HR2 - 1.5 ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..09T3..
Geometry
Material Tensile strength Hardness ap HR2 MM3
ISO
classification (N/mm2) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.10 0.35 0.08 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.30 0.05 0.28

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.05 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 5.00 0.10 0.35 0.08 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S Ni-based alloy 1177 350
- - - -

Ti-alloy 1262 370

Aluminum 260 75
N Aluminum alloy 447 130
- - - -

Hardened steel - 50-60HRC

H 0.06 0.20 - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

155
 Milling

AFM75-SD09
75° Approach angle milling face cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM75-025-Z02-W25R-SD09-C 25 25 96 40 6 2
SD..09T3
AFM75-032-Z03-W32R-SD09-C 32 32 100 40 6 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM75-040-Z04-A16R-SD09-C 40 16 32 - 6 4

AFM75-050-Z05-A22R-SD09-C 50 22 40 - 6 5

AFM75-063-Z06-A22R-SD09-C 63 22 40 - 6 6 SD..09T3

AFM75-080-Z08-A27R-SD09-C 80 27 50 - 6 8

AFM75-100-Z10-A32R-SD09-C 100 32 50 - 6 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ25-32
3.5Nm
ST040075 DT-T15

φ40-100 SP040090 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

156
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 09T304EN-MM3 0.4 - ● ● ● ●

SDMT 09T308EN-MM3 0.8 - ● ● ● ●

SDMW 09T308EN-HR2 0.8 - ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..09T3..
Geometry
Material Tensile strength Hardness ap HR2 MM3
ISO
classification (N/mm2 ) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.10 0.35 0.08 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.30 0.05 0.28

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.05 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 6.00 0.10 0.35 0.08 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S Ni-based alloy 1177 350
- - - -

Ti-alloy 1262 370

Aluminum 260 75
N Aluminum alloy 447 130
- - - -

Hardened steel - 50-60HRC

H 0.06 0.20 - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

157
 Milling

AFM90-SD09
90° Approach angle face milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM90-025-Z02-W25R-SD09-C 25 25 120 30 6 2
SD..09T3
AFM90-032-Z03-W32R-SD09-C 32 32 120 35 6 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM90-040-Z04-A16R-SD09-C 40 16 40 - 6 4

AFM90-050-Z05-A22R-SD09-C 50 22 40 - 6 5

AFM90-063-Z06-A22R-SD09-C 63 22 40 - 6 6 SD..09T3

AFM90-080-Z08-A27R-SD09-C 80 27 50 - 6 8

AFM90-100-Z10-A32R-SD09-C 100 32 50 - 6 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ25-32
3.5Nm
ST040075 DT-T15

φ40-100 SP040090 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

158
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 09T304EN-MM3 0.4 - ● ● ● ●

SDMT 09T308EN-MM3 0.8 - ● ● ● ●

SDGT 09T3PDER-MR6 0.8 1.2 ● ● ● ●

SDMW 09T308EN-HR2 0.8 - ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..09T3..
Geometry
Material Tensile strength Hardness ap HR2 MM3
ISO
classification (N/mm2 ) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.10 0.35 0.08 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.30 0.05 0.28

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.05 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 6.00 0.10 0.35 0.08 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
0.06 0.20 - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

159
 Milling

AFM45-SD12
45° Approach angle face milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-050-Z04-A22R-SD12-C 50 22 40 - 7 4

AFM45-063-Z05-A22R-SD12-C 63 22 40 - 7 5

AFM45-080-Z06-A27R-SD12-C 80 27 50 - 7 6 SD..1204

AFM45-100-Z07-A32R-SD12-C 100 32 50 - 7 7

AFM45-125-Z08-A40R-SD12-C 125 40 63 - 7 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-125 5.0Nm

SP04511555 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

160
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 120408EN-MM4 0.8 - ● ● ● ●

SDMT 120412EN-MM3 1.2 - ● ● ●

SDKT 1204AEEN-MR2 - 1.5 ● ● ● ● ●

SDHT 1204AEEN-MR6 - 1.5 ● ● ● ●

SDMW 120412EN-HR2 1.2 - ● ● ●

SDHW 1204AESN-HR2 - 2 ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..1204..
Geometry
Material Tensile strength Hardness ap HR2 MR2 MR6 MM3
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.20 0.40 0.15 0.30 0.15 0.35 0.12 0.28
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.20 0.35 0.15 0.25 0.15 0.30 0.10 0.25

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.12 0.25 - - 0.08 0.20

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 7.00 0.15 0.30 0.10 0.22 0.15 0.30 0.12 0.28

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - - - - - 0.08 0.20
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H 0.08 0.25 - - - - - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

161
 Milling

AFM75-SD12
75° Approach angle face milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM75-032-Z02-W32R-SD12-C 32 32 114 49 8 2
SD..1204
AFM75-040-Z03-W32R-SD12-C 40 32 114 49 8 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM75-050-Z04-A22R-SD12-C 50 22 40 - 8 4

AFM75-063-Z05-A22R-SD12-C 63 22 40 - 8 5

AFM75-080-Z06-A27R-SD12-C 80 27 50 - 8 6 SD..1204

AFM75-100-Z07-A32R-SD12-C 100 32 50 - 8 7

AFM75-125-Z08-A40R-SD12-C 125 40 63 - 8 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ32-125 5.0Nm

SP04511555 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

162
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 120408EN-MM4 0.8 - ● ● ● ●

SDMT 120412EN-MM3 1.2 - ● ● ●

SDMW 120412EN-HR2 1.2 - ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..1204..
Geometry
Material Tensile strength Hardness ap HR2 MM3
ISO
classification ( N/mm2) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.12 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.30 0.10 0.25

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.10 0.22

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 8.00 0.15 0.35 0.12 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - 0.10 0.20
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H 0.08 0.25 - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

163
 Milling

AFM90-SD12
90° Approach angle face milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM90-050-Z04-A22R-SD12-C 50 22 40 - 9 4

AFM90-063-Z05-A22R-SD12-C 63 22 40 - 9 5

AFM90-080-Z06-A27R-SD12-C 80 27 50 - 9 6 SD..1204

AFM90-100-Z08-A32R-SD12-C 100 32 50 - 9 8

AFM90-125-Z10-A40R-SD12-C 125 40 63 - 9 10

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-125 5.0Nm

SP04511555 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

164
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SDMT 120408EN-MM4 0.8 - ● ● ● ●

SDMT 120412EN-MM3 1.2 - ● ● ●

SDGT 1204PDER-MR6 0.8 1.6 ● ● ● ●

SDMW 120412EN-HR2 1.2 - ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SD..1204..
Geometry
Material Tensile strength Hardness ap HR2 MM3
ISO
classification ( N/mm2) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.12 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.30 0.10 0.25

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 - - 0.10 0.22

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 9.00 0.15 0.35 0.12 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - 0.10 0.20
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H 0.08 0.25 - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

165
 Milling

AFM45-SN12/SN19
45°Approach angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM45-050-Z04-A22R-SN12-N-C 50 22 40 6.5 4

AFM45-050-Z06-A22R-SN12-N-C 50 22 40 6.5 6

AFM45-063-Z04-A22R-SN12-N-C 63 22 40 6.5 4

AFM45-063-Z06-A22R-SN12-N-C 63 22 40 6.5 6

AFM45-063-Z08-A22R-SN12-N-C 63 22 40 6.5 8

AFM45-080-Z04-A27R-SN12-N-C 80 27 50 6.5 4

AFM45-080-Z05-A27R-SN12-N-C 80 27 50 6.5 5

AFM45-080-Z07-A27R-SN12-N-C 80 27 50 6.5 7 SN □ X 1206ANN

AFM45-100-Z06-A32R-SN12-N-C 100 32 50 6.5 6 SN □ X1206..

AFM45-100-Z08-A32R-SN12-N-C 100 32 50 6.5 8

AFM45-125-Z07-A40R-SN12-N-C 125 40 63 6.5 7

AFM45-125-Z08-A40R-SN12-N-C 125 40 63 6.5 8

AFM45-125-Z10-A40R-SN12-N-C 125 40 63 6.5 10

AFM45-160-Z10-A40R-SN12-N 160 40 63 6.5 10

AFM45-200-Z14-A60R-SN12-N 200 60 63 6.5 14

AFM45-250-Z16-A60R-SN12-N 250 60 63 6.5 16

AFM45-160-Z08-A40R-SN19 160 40 63 11 8

AFM45-200-Z10-A60R-SN19 200 60 63 11 10 SN □ X1909ANN

AFM45-250-Z12-A60R-SN19 250 60 63 11 12

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-250(SN..1206ANN)

SP050120 DT-TP20 5.0Nm

φ160-250(SN..1909ANN) SP06018070 DT-TP25 5.0Nm

Note: With internal coolant

Without internal coolant

P310 P224 P248

166
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm
SNGX 1206ANN-MM3 - 1.8 ● ● ● ● ●

SNGX 1206ANN-MM4 - 1.8 ● ● ● ● ●

SNGX 1206ANN-MR6 - 1.8 ● ● ● ● ●

SNGX 1206ANN-RR2 - 1.8 ● ● ● ● ●

SNGX 1909ANN-MM3 - 2.9 ●

SNGX 1909ANN-MR6 - 2.9 ●

SNGX 120608-MM4 0.8 - ● ● ● ● ●

SNGX 120612-MM4 1.2 - ●

SNMX 1206ANN-MM3 - 1.8 ● ● ● ● ●

SNMX 1206ANN-MM4 - 1.8 ● ● ● ● ●

SNMX 1206ANN-MR6 - 1.8 ● ● ● ● ●

SNMX 120608-MM4 0.8 - ● ● ● ● ●

Milling cutters
SNMX 120612-MM3 1.2 - ● ● ● ● ●

SNMX 120612-MM4 1.2 - ● ● ● ● ●

SNMX 120612-MR6 1.2 - ● ● ● ● ●

SNMX 120612-RR2 1.2 - ● ● ● ● ●

SNMX 120620-MM4 2.0 - ● ● ● ● ●

SNMX 120620-RR2 2.0 - ● ● ● ● ●

SNHX 1206ANN-FM2 - 1.8 ●

SNHX 1206ANN-W - 6.7 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SN..1206..
Geometry
Tensile ap MM3 MM4 MR6 RR2 FM2
Material Hardness
ISO strength
classification (HB) fz
( N/mm2 )
(mm)
min max min max min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.18 0.38 0.18 0.40 0.18 0.45 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.32 0.15 0.35 0.15 0.38 0.15 0.38 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.12 0.30 0.12 0.32 - - - - - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 6.50 0.15 0.35 0.18 0.38 0.18 0.40 0.18 0.45 - -
Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S
Ni-based alloy 1177 350
0.10 0.25 0.12 0.28 - - - - - -
Ti-alloy 1262 370

Aluminum 260 75
N - - - - - - - - 0.15 0.35
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - - - - - - - - - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248 167
 Milling

AFM75-SN12
75° Approach angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM75-050-Z04-A22R-SN12-N-C 50 22 40 8.0 4

AFM75-063-Z06-A22R-SN12-N-C 63 22 40 8.0 6

AFM75-080-Z07-A27R-SN12-N-C 80 27 50 8.0 7

AFM75-100-Z08-A32R-SN12-N-C 100 32 50 8.0 8

SNGX1206ENN
SN □ X1206..
AFM75-125-Z08-A40R-SN12-N-C 125 40 63 8.0 8

AFM75-125-Z10-A40R-SN12-N-C 125 40 63 8.0 10

AFM75-160-Z10-A40R-SN12-N 160 40 63 8.0 10

AFM75-200-Z14-A60R-SN12-N 200 60 63 8.0 14

AFM75-250-Z16-A60R-SN12-N 250 60 63 8.0 16

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-250 5.0Nm

SP050120 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

168
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SNGX 1206ENN-MM3 - 1.2 ● ● ● ● ●

SNGX 1206ENN-MM4 - 1.2 ● ● ● ● ●

SNGX 1206ENN-MR6 - 1.2 ● ● ● ● ●

SNGX 120608-MM4 0.8 - ● ● ● ● ●

SNGX 120612-MM4 1.2 - ●

SNMX 1206ENN-MM4 - 1.2 ●

SNMX 120608-MM4 0.8 - ● ● ● ● ●

SNMX 120612-MM3 1.2 - ● ● ● ● ●

Milling cutters
SNMX 120612-MM4 1.2 - ● ● ● ● ●

SNMX 120612-MR6 1.2 - ● ● ● ● ●

SNMX 120612-RR2 1.2 - ● ● ● ● ●

SNMX 120620-MM4 2.0 - ● ● ● ● ●

SNMX 120620-RR2 2.0 - ● ● ● ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SN..1206..
Geometry
Material Tensile strength Hardness ap MM3 MM4 MR6 RR2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.12 0.32 0.19 0.35 0.15 0.38 0.18 0.40
<950 <280
P 700-950 200-280

Alloyed steel 950-1200 280-355 0.10 0.30 0.12 0.32 0.10 0.35 0.15 0.35

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.10 0.28 0.10 0.30 - - - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 8.00 0.12 0.32 0.15 0.35 0.12 0.35 0.18 0.40

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.10 0.22 0.10 0.25 - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - - - - - - - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

169
 Milling

AFM88-SN12
88° Approach angle face milling cutter

Product code D d1 L apmax Internal coolant Z Inserts

AFM88-050-Z04-A22R-SN12-N-C 50 22 40 10.0 4

AFM88-063-Z04-A22R-SN12-N-C 63 22 40 10.0 4

AFM88-063-Z06-A22R-SN12-N-C 63 22 40 10.0 6

AFM88-080-Z04-A27R-SN12-N-C 80 27 50 10.0 4

AFM88-080-Z07-A27R-SN12-N-C 80 27 50 10.0 7
SNGX1206ZNN
SN □ X1206..
AFM88-100-Z08-A32R-SN12-N-C 100 32 50 10.0 8

AFM88-100-Z11-A32R-SN12-N-C 100 32 50 10.0 11

AFM88-125-Z10-A40R-SN12-N-C 125 40 63 10.0 10

AFM88-125-Z13-A40R-SN12-N-C 125 40 63 10.0 13

AFM88-160-Z12-A40R-SN12-N 160 40 63 10.0 12

AFM88-200-Z14-A60R-SN12-N 200 60 63 10.0 14

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ50-200 5.0Nm

SP050120 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

170
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

SNGX 1206ZNN-MM3 - 1.2 ● ● ● ● ●

SNGX 1206ZNN-MM4 - 1.2 ● ● ● ● ●

SNGX 1206ZNN-MR6 - 1.2 ● ● ● ● ●

SNGX 120608-MM4 0.8 - ● ● ● ● ●

SNGX 120612-MM4 1.2 - ●

SNMX 120608-MM4 0.8 - ● ● ● ● ●

SNMX 120612-MM3 1.2 - ● ● ● ● ●

SNMX 120612-MM4 1.2 - ● ● ● ● ●

Milling cutters
SNMX 120612-MR6 1.2 - ● ● ● ● ●

SNMX 120612-RR2 1.2 - ● ● ● ● ●

SNMX 120620-MM4 2.0 - ● ● ● ● ●

SNMX 120620-RR2 2.0 - ● ● ● ● ●

SNHX 1206ZNN-FM2 - 1.2 ●

SNHX 1206ZNN-W 1.0 4.4 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

SN..1206..
Geometry
Material Tensile strength Hardness ap MM3 MM4 MR6 RR2 FM2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max min max min max
<600 <180
Unalloyed steel 0.12 0.32 0.19 0.35 0.15 0.38 0.18 0.40 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.10 0.30 0.12 0.32 0.10 0.35 0.15 0.35 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.10 0.28 0.10 0.30 - - - - - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 10.00 0.12 0.32 0.15 0.35 0.12 0.35 0.18 0.40 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.10 0.22 0.10 0.25 - - - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - - - - - 0.12 0.32
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - - - - - - - - - -
Chilled cast iron - 55HRC
*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248
171
 Milling

AFM45-XN07
45° Approach angle face milling cutter

45°
Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-040-Z03-M16R-XN07-C 40 16 70 43 4.4 3 XN..U 0705

45°
Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-040-Z03-W40R-XN07-C 40 40 130 35 4.4 3 XN..U 0705

45°

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-040-Z03-A16R-XN07-C 40 16 40 - 4.4 3
AFM45-050-Z04-A22R-XN07-C 50 22 40 - 4.4 4
AFM45-050-Z05-A22R-XN07-C 50 22 40 - 4.4 5
AFM45-063-Z05-A22R-XN07-C 63 22 40 - 4.4 5
AFM45-063-Z06-A22R-XN07-C 63 22 40 - 4.4 6
AFM45-080-Z06-A27R-XN07-C 80 27 50 - 4.4 6
AFM45-080-Z07-A27R-XN07-C 80 27 50 - 4.4 7 XN..U 0705
AFM45-100-Z07-A32R-XN07-C 100 32 50 - 4.4 7
AFM45-100-Z08-A32R-XN07-C 100 32 50 - 4.4 8
AFM45-125-Z08-A40R-XN07-C 125 40 63 - 4.4 8
AFM45-125-Z10-A40R-XN07-C 125 40 63 - 4.4 10
AFM45-160-Z09-A40R-XN07 160 40 63 - 4.4 9
AFM45-160-Z12-A40R-XN07 160 40 63 - 4.4 12

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ40-160 3.5Nm

SP035120H DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

172
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

XNGU 0705ANN-MM3 0.8 1.1 ● ● ●

XNGU 0705ANN-MM4 0.8 1.1 ● ●

XNMU 0705ANN-MM4 0.8 1.1 ● ● ● ● ● ●

XNMU 0705ANN-MR6 0.8 1.1 ● ● ● ●

XNMU 070508-MM4 0.8 - ● ● ● ●

XNGX 0705ANN-W 1.0 6 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

XN.. 0705..
Geometry
Material Tensile strength Hardness ap MM3 MM4 MR6
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.18 0.38 0.18 0.40
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.32 0.15 0.35 0.15 0.38

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.12 0.30 0.12 0.32 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 4.40 0.15 0.35 0.18 0.38 0.18 0.40

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.10 0.25 0.12 0.28 - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

173
 Milling

AFM45-XN09
45° Approach angle face milling cutter

45°

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-063-Z05-A22R-XN09-C 63 22 40 - 6.0 5
AFM45-080-Z06-A27R-XN09-C 80 27 50 - 6.0 6
AFM45-100-Z07-A32R-XN09-C 100 32 50 - 6.0 7
AFM45-100-Z08-A32R-XN09-C 100 32 50 - 6.0 8
AFM45-125-Z08-A40R-XN09-C 125 40 63 - 6.0 8 XN..U 0906
AFM45-125-Z10-A40R-XN09-C 125 40 63 - 6.0 10
AFM45-160-Z09-A40R-XN09 160 40 63 - 6.0 9
AFM45-160-Z11-A40R-XN09 200 60 63 - 6.0 11
AFM45-200-Z12-A60R-XN09 200 60 63 - 6.0 12

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ63-200 5.0Nm

SP050130 DT-TP20

AFM45-XN09-W
45° Approach angle face milling cutter
with wedge clamping

Product code D d1 L l1 apmax Internal coolant Z Inserts

AFM45-080-Z09-A27R-XN09-W 80 27 50 - 6.0 9
AFM45-100-Z12-A32R-XN09-W 100 32 50 - 6.0 12
AFM45-125-Z16-A40R-XN09-W 125 40 63 - 6.0 16
AFM45-125-Z16-A40L-XN09-W 125 40 63 - 6.0 16
XN..U 0906
AFM45-160-Z20-A40R-XN09-W 160 40 63 - 6.0 20
AFM45-160-Z20-A40L-XN09-W 160 40 63 - 6.0 20
AFM45-200-Z26-A60R-XN09-W 200 60 63 - 6.0 26
AFM45-200-Z26-A60L-XN09-W 200 60 63 - 6.0 26

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ80-200 7.0Nm
AWG-8H AWS830F AWH4
Note: With internal coolant

Without internal coolant

P310 P224 P248

174
Milling

Dimension(mm) Grades

AW100K
Insert corner

AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

XNGU 0906ANN-MM3 0.8 1.4 ● ● ● ●

XNGU 0906ANN-MM4 0.8 1.4 ● ● ● ●

XNMU 0906ANN-MR6 0.8 1.4 ● ● ●

XNMU 090612-MM4 1.2 - ● ● ● ● ●

XNGX 0906ANN-W 1.0 7.5 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

XN..0906..
Geometry
Material Tensile strength Hardness ap MM3 MM4 MR6
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.35 0.18 0.38 0.18 0.40
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.12 0.32 0.15 0.35 0.15 0.38

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.12 0.30 0.12 0.32 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 6.00 0.15 0.35 0.18 0.38 0.18 0.40

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.10 0.25 0.12 0.28 - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

175
 Milling

AFF40-LN12/LN15
Cast iron finishing milling cutter

d1

D apmax

Internal Cutting edge for

Product code D d1 L apmax *Z Inserts
coolant finishing machining
AFF40-080-Z08-A27R-LN12 80 27 50 0.5 8+2 2 ONHF 050408-MM3
AFF40-100-Z10-A32R-LN12 100 32 50 0.5 10+2 2 LNHQ 120408FN-W

AFF40-125-Z15-A40R-LN15 125 40 63 0.5 15+3 3

AFF40-160-Z18-A40R-LN15 160 40 63 0.5 18+3 3 ONHF 050408-MM3
AFF40-200-Z24-A60R-LN15 200 60 63 0.5 24+3 3 LNHQ 150416FN-W

AFF40-250-Z30-A60R-LN15 250 60 63 0.5 30+3 3

Dimension Spare parts

Cutter wedge locking wiper insert locking wiper insert adjusting wiper cartridge locking
wedge type
diameter screw screw screw screw

φ80-250
AWG-6H-13B WD060200 SP040085H AH050100F SH060250

Dimension Spare parts

Cutter wiper insert wiper insert adjusting wiper insert cartridge

wedge screw wrench wiper cartridge
diameter screw wrench screw wrench locking screw wrench

φ80-250
D80-100 D125-250
LT-H3 DT-TP10 LT-H2.5 LT-H5
C-LN1235-2545 C-LN1535-2545

Note: With internal coolant

Without internal coolant

P310 P224 P248

176
Milling

Dimension(mm) Grades

AP151H
Product code Insert corner radius Wiper length
mm mm

ONHF 050408-MM3 0.8 - ●

LNHQ 120408FN-W 0.8 - ●

LNHQ 150416FN-W 1.6 - ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

ONHF..05 + LNHQ 12/15
Geometry
Material Tensile strength Hardness ap MM3 + W
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 0.50 0.08 0.25

Malleable cast iron 800 250

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

177
 Milling

ASM90-LN09-C
90°Shoulder milling cutter

D d1

apmax
L1
L

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-025-Z03-W25R-LN09-C 25 25 100 45 8 3
ASM90-025-Z04-W25R-LN09-C 25 25 100 45 8 4
ASM90-032-Z04-W32R-LN09-C 32 32 110 50 8 4
LNHU 0904
ASM90-032-Z05-W32R-LN09-C 32 32 110 50 8 5
ASM90-040-Z04-W32R-LN09-C 40 32 110 25 8 4
ASM90-040-Z06-W32R-LN09-C 40 32 110 25 8 6

D d1

apmax
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-020-Z02-C20R-LN09-L110 20 20 110 31 8 2
ASM90-020-Z03-C20R-LN09-L110 20 20 110 31 8 3
ASM90-025-Z03-C25R-LN09-L200-C 25 25 200 40 8 3
LNHU 0904
ASM90-025-Z04-C25R-LN09-L200-C 25 25 200 40 8 4
ASM90-032-Z04-C32R-LN09-L250-C 32 32 250 50 8 4
ASM90-032-Z05-C32R-LN09-L250-C 32 32 250 50 8 5

d1

apmax
D

Product code D d1 L ISO apmax Internal coolant Z Inserts

ASM90-040-Z04-A16R-LN09-C 40 16 40 A 8 4
ASM90-040-Z06-A16R-LN09-C 40 16 40 A 8 6
ASM90-050-Z05-A22R-LN09-C 50 22 40 A 8 5
ASM90-050-Z07-A22R-LN09-C 50 22 40 A 8 7
LNHU 0904
ASM90-063-Z07-A22R-LN09-C 63 22 40 A 8 7
ASM90-063-Z10-A22R-LN09-C 63 22 40 A 8 10
ASM90-080-Z09-A27R-LN09-C 80 27 50 A 8 9
ASM90-080-Z13-A27R-LN09-C 80 27 50 A 8 13
Note: With internal coolant

Without internal coolant

P310 P224 P248

178
Milling

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ20-80 1.8Nm

SP030083 DT-TP09

Dimension(mm) Grade

AP403M

AW100K
Insert corner

AP301U

AC301P

AP351U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

LNHU 090404ER-FM2 0.4 1.85 ●

LNHU 090404ER-MM3 0.4 1.85 ● ●

LNHU 090404ER-MR2 0.4 1.85 ● ● ● ● ●

Milling cutters
LNHU 090408ER-MR2 0.8 1.3 ● ● ● ● ●

LNHU 090412ER-MR2 1.2 1.0 ● ● ●

LNHU 090416ER-MR2 1.6 0.65 ● ● ●

LNHU 090420ER-MR2 2.0 0.65 ● ● ●

LNHU 0904PDER-W 0.4 3.6 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNHU 0904..
Geometry
Material Tensile strength Hardness ap MR2 MM3 FM2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.08 0.28 0.08 0.25 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.06 0.22 0.06 0.20 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.06 0.22 0.06 0.20 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 8.00 0.08 0.30 0.08 0.28 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - - 0.08 0.15 - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - 0.06 0.25
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

179
 Milling

ASM90-LN13-C
90°Shoulder milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-040-Z05-W32R-LN13-C 40 32 120 50 12 5 LNHU 1306

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-040-Z04-A16R-LN13-C 40 16 40 - 12.0 4

ASM90-040-Z05-A16R-LN13-C 40 16 40 - 12.0 5

ASM90-050-Z05-A22R-LN13-C 50 22 40 - 12.0 5

ASM90-050-Z06-A22R-LN13-C 50 22 40 - 12.0 6

ASM90-063-Z04-A22R-LN13-C 63 22 40 - 12.0 4

ASM90-063-Z06-A22R-LN13-C 63 22 40 - 12.0 6

ASM90-063-Z08-A22R-LN13-C 63 22 40 - 12.0 8

ASM90-080-Z05-A27R-LN13-C 80 27 50 - 12.0 5

ASM90-080-Z07-A27R-LN13-C 80 27 50 - 12.0 7
LNHU 1306
ASM90-080-Z10-A27R-LN13-C 80 27 50 - 12.0 10

ASM90-100-Z07-A32R-LN13-C 100 32 50 - 12.0 7

ASM90-100-Z09-A32R-LN13-C 100 32 50 - 12.0 9

ASM90-100-Z13-A32R-LN13-C 100 32 50 - 12.0 13

ASM90-125-Z09-A40R-LN13-C 125 40 63 - 12.0 9

ASM90-125-Z11-A40R-LN13-C 125 40 63 - 12.0 11

ASM90-125-Z16-A40R-LN13-C 125 40 63 - 12.0 16

ASM90-160-Z09-A40R-LN13 160 40 63 - 12.0 9

ASM90-160-Z13-A40R-LN13 160 40 63 - 12.0 13

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ40-160 3.5Nm

SP040115 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

180
Milling

Dimension(mm) Grade

AW100K
Insert corner

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

LNHU 130608ER-FM2 0.8 2.7 ●

LNHU 130608ER-MM3 0.8 2.7 ●

LNHU 130608ER-MR2 0.8 2.7 ● ● ● ● ● ●

LNHU 130612ER-MR2 1.2 2.3 ● ● ●

LNHU 130616ER-MR2 1.6 1.9 ● ● ●

LNHU 130620ER-MR2 2.0 1.5 ● ●

LNHU 130624ER-MR2 2.4 1.0 ● ●

LNHU 130631ER-MR2 3.1 0.4 ● ● ●

Milling cutters
LNHU 1306PDER-W 0.8 5.6 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNHU..1306..
Geometry
Material Tensile strength Hardness ap MM3 MR2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.10 0.30 0.12 0.35
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.25 0.10 0.30

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.06 0.20 0.08 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 12.00 - - 0.12 0.35

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.06 0.18 0.08 0.22
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - - 0.08 0.20
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

181
 Milling

ASM90-LN16-C
90° Shoulder milling cutter
d1

apmax
D

Product code D d1 L ISO apmax Internal coolant Z Inserts

ASM90-063-Z04-A22R-LN16-C 63 22 40 A 15 4

ASM90-080-Z05-A27R-LN16-C 80 27 50 A 15 5

ASM90-100-Z06-A32R-LN16-C 100 32 50 A 15 6 LNHU 1607

ASM90-125-Z07-A40R-LN16-C 125 40 63 A 15 7

ASM90-160-Z08-A40R-LN16 160 40 63 A 15 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ63-160 5Nm

SP05013063 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

182
Milling

Dimension(mm) Grade

AW100K
Insert corner

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

LNHU 160708ER-MR2 0.8 1.97 ● ● ● ●

LNHU 160716ER-MR2 1.6 1.5 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNHU 1607..
Geometry
Material Tensile strength Hardness ap MR2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max
<600 <180
Unalloyed steel 0.10 0.30
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.28

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.08 0.25

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 15.00 0.10 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

183
 Milling

ASM90-WN08-C
90° Shoulder milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-040-Z03-W32R-WN08-C 40 32 120 35 7.0 3
WN.U 0806
ASM90-040-Z04-W32R-WN08-C 40 32 120 35 7.0 4

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-050-Z04-A22R-WN08-C 50 22 40 - 7 4
ASM90-050-Z05-A22R-WN08-C 50 22 40 - 7 5
ASM90-063-Z04-A22R-WN08-C 63 22 40 - 7 4
ASM90-063-Z06-A22R-WN08-C 63 22 40 - 7 6
ASM90-063-Z07-A22R-WN08-C 63 22 40 - 7 7
ASM90-080-Z05-A27R-WN08-C 80 27 50 - 7 5
ASM90-080-Z07-A27R-WN08-C 80 27 50 - 7 7
ASM90-080-Z09-A27R-WN08-C 80 27 50 - 7 9
ASM90-100-Z06-A32R-WN08-C 100 32 50 - 7 6
WN.U 0806
ASM90-100-Z08-A32R-WN08-C 100 32 50 - 7 8
ASM90-100-Z11-A32R-WN08-C 100 32 50 - 7 11
ASM90-125-Z07-A40R-WN08-C 125 40 63 - 7 7
ASM90-125-Z11-A40R-WN08-C 125 40 63 - 7 11
ASM90-125-Z13-A40R-WN08-C 125 40 63 - 7 13
ASM90-160-Z08-A40R-WN08 160 40 63 - 7 8
ASM90-160-Z12-A40R-WN08 160 40 63 - 7 12
ASM90-200-Z14-A60R-WN08 200 60 63 - 7 14
ASM90-250-Z16-A60R-WN08 250 60 63 - 7 16

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ40-250 3.5Nm

SP040090 DT-TP15

Note: With internal coolant

Without internal coolant

P310 P224 P248

184
Milling

Dimension(mm) Grade

AW100K
Insert corner

AP151H
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

WNHU 080608R-FM2 0.8 2.0 ●

WNGU 080604R-MM3 0.4 2.2 ● ●

WNGU 080608R-MM3 0.8 2.0 ● ● ●

WNGU 080604R-MM4 0.4 2.2 ● ● ● ●

WNGU 080608R-MM4 0.8 2.0 ● ● ● ● ● ● ●

WNGU 080612R-MM4 1.2 1.6 ● ● ●

WNGU 080616R-MM4 1.6 1.2 ● ● ●

WNGU 080608R-MR2 0.8 2.0 ● ●

Milling cutters
WNGU 080612R-MR2 1.2 1.6 ● ●

WNGU 080616R-MR2 1.6 1.2 ● ●

WNHX 0806ZZR-W 1.0 4.8 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

WNGU..0806..
Geometry
Material Tensile strength Hardness ap FM2 MM3 MM4 MR2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.12 0.25 0.12 0.28 0.12 0.30
<950 <280
P 700-950 200-280

Alloyed steel 950-1200 280-355 0.10 0.20 0.10 0.25 0.10 0.28

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.08 0.18 0.08 0.18 - -

Precipitation-hardening stainless steel 1013 300 - -

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 7.00 0.12 0.20 0.10 0.28 0.15 0.30

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.12 0.13 0.10 0.15 - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N 0.10 0.24 - - - - - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H - - - - - - - -
Chilled cast iron - 55HRC

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

185
 Milling

ASM90-AP10-C
90° Shoulder milling cutter

D d1

apmax

l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-016-Z02-C16R-AP10-L90-C 16 16 90 26 8 2

ASM90-020-Z03-C20R-AP10-L110-C 20 20 110 28 8 3
APKT 1003
ASM90-025-Z04-C25R-AP10-L120-C 25 25 120 30 8 4

ASM90-032-Z05-C32R-AP10-L130-C 32 32 130 26 8 5

d1

D apmax

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-063-Z07-A22R-AP10-C 63 22 40 A 8 7 APKT 1003

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ16-63 1.0Nm

SP02506450H DT-TP08

Note: With internal coolant

Without internal coolant

P310 P224 P248

186
Milling

Dimension(mm) Grade
Insert corner

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

AP403S
Product code Wiper length
radius
mm
mm

APKT 1003PDER-IT 0.8 1.09 ● ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

APKT..1003..
Geometry
Material Tensile strength Hardness ap IT
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max
<600 <180
Unalloyed steel 0.05 0.22
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.05 0.18

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.05 0.15

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 8.00 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.05 0.15
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N 0.05 0.25
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

187
 Milling

ASM90-AP17-C
90° Shoulder milling cutter

D d1

apmax

l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-025-Z02-C25R-AP17-L100-C 25 25 100 39 16 2

ASM90-032-Z03-C32R-AP17-L110-C 32 32 110 40 16 3 APKT 1705

ASM90-040-Z04-C32R-AP17-L120-C 40 32 120 45 16 4

d1

apmax
D

Product code D d1 L l1 apmax Internal coolant Z Inserts

ASM90-050-Z05-A22R-AP17-C 50 22 40 - 16 5
APKT 1705
ASM90-063-Z06-A22R-AP17-C 63 22 40 - 16 6

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ25
φ32-63
3.5Nm
SP040084
DT-TP15
SP040093

Note: With internal coolant

Without internal coolant

P310 P224 P248

188
Milling

Dimension(mm) Grade

AW100K
Insert corner

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

APKT 1705PER-DT 0.8 2.16 ● ● ● ● ● ●

APKT 170516R-DT 1.6 1.7 ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

APKT..1705..
Geometry
Material Tensile strength Hardness ap DT
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max
<600 <180
Unalloyed steel 0.08 0.25
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.06 0.22

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.06 0.20

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 16.00 0.08 0.25

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.06 0.18
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N 0.06 0.30
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

189
 Milling

APE90-LN09 D d1

90° Procupine milling cutter

apmax

l1

Internal clamping Insert

Product code D d1 L L1 d2 d3 d4 apmax Z row Inserts
coolant screw number
APE90-025-Z02-W25R-LN09-L32-F-C 25 25 100 43 - - - 32 - 2 4 8
APE90-032-Z02-W32R-LN09-L32-F-C 32 32 105 44 - - - 32 - 2 4 8
LNHU
APE90-032-Z02-W32R-LN09-L40-F-C 32 32 110 50 - - - 40 - 2 5 10
0904
APE90-040-Z03-W40R-LN09-L40-F-C 40 40 125 55 - - - 40 - 3 5 15
APE90-040-Z03-W40R-LN09-L48-F-C 40 40 130 59 - - - 48 - 3 6 18

D d4 d3 d2 d1

apmax
L

Internal clamping Insert

Product code D d1 L L1 d2 d3 d4 apmax Z row Inserts
coolant screw number
APE90-040-Z03-A16R-LN09-L32-F-C 40 38 55 - 16 9 15 32 SH080400 3 4 12
LNHU
APE90-040-Z03-A16R-LN09-L40-F-C 40 38 65 - 16 9 15 40 SH080500 3 5 15
0904
APE90-050-Z04-A22R-LN09-L48-F-C 50 47.5 75 - 22 11 18 48 SH100550 4 6 24

clamping screw Designation screw type clamping torque

SH080400 M8*40 41Nm

SH080500 M8*50 41Nm

SH100550 M10*55 81Nm

D M d1

apmax

l1

Internal clamping Insert

Product code D d1 L L1 d2 M d4 apmax Z row Inserts
coolant screw number
APE90-025-Z02-M12R-LN09-L24-F-C 25 23.4 64 40 12 12 - 24 - 2 3 6
LNHU
APE90-032-Z02-M16R-LN09-L24-F-C 32 30 67 40 16 16 - 24 - 2 3 6
0904
APE90-032-Z02-M16R-LN09-L32-F-C 32 30 77 50 16 16 - 32 - 2 4 8
Notice of inserts mounting:
For APE90-LN09 series: end insert must use corner radius R≤0.8, all side inserts must use corner radius R=0.4 to have right cutting edge overlapping.

Dimension(mm) Spare parts

Cutter diameter wrench Screw wrench Torque

φ25-50 1.8Nm

AFW-15/24 SP030083 DT-TP09

Note: With internal coolant

Without internal coolant

P310 P224 P248

190
Milling

Dimension(mm) Grade

AP403M

AW100K
Insert corner

AP301U

AC301P

AP351U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

LNHU 090404ER-FM2 0.4 1.85 ●

LNHU 090404ER-MM3 0.4 1.85 ● ●

LNHU 090404ER-MR2 0.4 1.85 ● ● ● ● ●

LNHU 090408ER-MR2 0.8 1.3 ● ● ● ● ●

LNHU 090412ER-MR2 1.2 1.0 ● ● ●

LNHU 090416ER-MR2 1.6 0.65 ● ● ●

LNHU 090420ER-MR2 2.0 0.65 ● ● ●

LNHU 0904PDER-W 0.4 3.6 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNHU..0904..
Geometry
Material Tensile strength Hardness ap MM3 MR2 FM2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.06 0.22 0.08 0.25 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.05 0.18 0.06 0.20 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.05 0.18 0.06 0.18 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 48.00 0.05 0.22 0.08 0.25 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.05 0.15 - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - 0.06 0.25
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - 0.05 0.12 - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

191
 Milling

APE90-LN13
90° Porcupine milling cutter

D d4 d3 d2 d1

apmax
L

Internal Mounting Insert

Product code D d1 L L1 d2 d3 d4 apmax Z Row Inserts
coolant bolts number
APE90-040-Z02-A16R-LN13-L34-F-C 40 39 55 - 16 9 15 34 SH100400 2 3 6

APE90-040-Z02-A16R-LN13-L45-F-C 40 39 65 - 16 9 15 45 SH100450 2 4 8

APE90-050-Z03-A22R-LN13-L34-F-C 50 47.5 55 - 22 11 18 34 SH100400 3 3 9

APE90-050-Z03-A22R-LN13-L45-F-C 50 47.5 65 - 22 11 18 45 SH100450 3 4 12 LNHU 1306

APE90-063-Z04-A27R-LN13-L56-F-C 63 59.5 80 - 27 14 20 56 SH120600 4 5 20

APE90-063-Z04-A27R-LN13-L45-F-C 63 59.5 70 - 27 14 20 45 SH120500 4 4 16

APE90-080-Z05-A32R-LN13-L56-F-C 80 75.6 85 - 32 18 26 56 SH160650 5 5 25

D d1

apmax

l1

Internal Insert
Product code D d1 L L1 d2 d3 d4 apmax Z Row Inserts
coolant number
APE90-040-Z02-W40R-LN13-L34-F-C 40 40 120 54 - - - 34 2 3 6
LNHU 1306
APE90-040-Z02-W40R-LN13-L45-F-C 40 40 135 64 - - - 45 2 4 8
Notice of inserts mounting:
APE90-LN13 series: end insert must use corner radius R≤2.4, all side inserts must use corner radius R=0.8 to have right cutting edge overlapping

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ40-80 3.5Nm

SP040115 DT-TP15

Mounting bolts Model Bolt specification Torque

SH080400 M8*40 41Nm

SH080500 M8*50 41Nm
SH100550 M10*55 81Nm
SH100400 M10*40 81Nm
SH100450 M10*45 81Nm
SH120500 M12*50 142Nm
SH120600 M12*60 142Nm
SH160650 M16*65 350Nm

Note: With internal coolant

Without internal coolant

P310 P224 P248

192
Milling

Dimension(mm) Grade

AW100K
Insert corner

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

LNHU 130608ER-FM2 0.8 2.7 ●

LNHU 130608ER-MM3 0.8 2.7 ●

LNHU 130608ER-MR2 0.8 2.7 ● ● ● ● ● ●

LNHU 130612ER-MR2 1.2 2.3 ● ● ●

LNHU 130616ER-MR2 1.6 1.9 ● ● ●

LNHU 130620ER-MR2 2.0 1.5 ● ●

LNHU 130624ER-MR2 2.4 1.0 ● ●

LNHU 130631ER-MR2 3.1 0.4 ● ● ●

Milling cutters
LNHU 1306PDER-W 0.8 5.6 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNHU..1306..
Geometry
Material Tensile strength Hardness ap MM3 MR2 FM2
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.10 0.28 0.10 0.30 - -
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.08 0.25 0.08 0.28 - -

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.08 0.22 0.08 0.25 - -

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 56 - - 0.10 0.32 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.08 0.2 - - - -
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - - 0.08 0.30
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - 0.06 0.15 - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

193
 Milling

APM00-RP
Ballnose milling cutter

L1

D1
D
AP

L2
L

Product code D d1 L l1 l2 apmax M Internal coolant Z Inserts

APM00-016-Z02-C20R-RP080-L120-C 16 20 120 50 70 14 - 2 RPM 080ER-MM4

APM00-020-Z02-C25R-RP100-L126-C 20 25 126 43 64 18 - 2
RPM 100ER-MM4
APM00-020-Z02-C25R-RP100-L176-C 20 25 176 43 106 18 - 2

L1

D1
D
AP
L

Product code D d1 L l1 M apmax M Internal coolant Z Inserts

APM00-016-Z02-M10R-RP080-C 16 18 49 28 10 14 M10 2 RPM 080ER-MM4

APM00-020-Z02-M10R-RP100-C 20 18 51 30 10 18 M10 2 RPM 100ER-MM4

Dimension(mm) Spare parts

Cutter diameter Screw Wrench wrench Torque

φ16 AFW-15 SP02506450H DT-TP08 1.2Nm

φ20 AFW-15 SP030072H DT-TP09 2.0Nm

Note: With internal coolant

Without internal coolant

P310 P224 P248

194
Milling

Dimension(mm) Grade

AP351M
Insert corner

AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code Wiper length
radius
mm
mm

RPM 080ER-MM4 8 - ● ● ●

RPM 100ER-MM4 10 - ● ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

RPM....
Geometry
Material Tensile strength Hardness ap MM4
ISO
classification ( N/mm2 ) (HB) fz
(mm)
min max min max
<600 <180
Unalloyed steel 0.10 0.20
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.10 0.18

1200-1400 355-415

Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.10 0.18

Precipitation-hardening stainless steel 1013 300

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 15.00 - -

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.06 0.12
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - -
Aluminum alloy 447 130

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

195
 Milling

APM00-RO08
Profile milling cutter

d1
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-016-Z02-W16R-RO08-L100 16 16 100 76 4 2
RO 0803
APM00-025-Z04-C25R-RO08-L116-C 25 25 116 60 4 4

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ16-25 2.0Nm

SP030072H DT-TP09

Note: With internal coolant

Without internal coolant

P310 P224 P248

196
Milling

Dimension(mm) Grade

AP403M
AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code
IC S

ROHT 0803M0E-MM3 8 3.18 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

ROHT..0803..
Geometry
MM3
Material Tensile strength Hardness ap
ISO fz
classification ( N/mm2 ) (HB)
0.1 ＜ ap ≤ 1 0.1 ＜ ap ≤ 4
(mm)
min max min max min max
<600 <180
Unalloyed steel 0.15 0.50 0.08 0.30
<950 <280

P 700-950 200-280
Alloyed steel 950-1200 280-355 0.12 0.45 0.06 0.28
1200-1400 355-415
Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.10 0.40 0.06 0.25

Precipitation-hardening stainless steel 1013 300
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 4.00 - - - -

Malleable cast iron 800 250
Fe-based alloy 943 280
Co-based alloy 1076 320
S 0.10 0.35 0.06 0.25
Ni-based alloy 1177 350
Ti-alloy 1262 370
Aluminum 260 75
N Aluminum alloy 447 130
- - - -

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

197
 Milling

APM00-RO10
Profile milling cutter

d1
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-025-Z03-C25R-RO10-L225-C 25 25 225 60 5 3
RO 10T3
APM00-032-Z04-C32R-RO10-L130-C 32 32 130 70 5 4

d1
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-025-Z03-M12R-RO10-C 25 M12 59 35 5 3
RO 10T3
APM00-032-Z04-M16R-RO10-C 32 M16 70 43 5 4

d1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-040-Z05-A16R-RO10-C 40 16 40 - 5 5
RO 10T3
APM00-050-Z06-A22R-RO10-C 50 22 40 - 5 6

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ25-50 2.0Nm

SP030072H DT-TP09

Note: With internal coolant

Without internal coolant

P310 P224 P248

198
Milling

Dimension(mm) Grade

AP403M
AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code
IC S

ROHT 10T3M8E-MM3 10 3.97 ● ●

ROMT 10T3M4E-MR6 10 3.97 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

RO..10T3..
Geometry

Tensile MM3 MR6

Material Hardness ap
ISO strength fz
classification (HB)
( N/mm2 ) 0.1 ＜ ap ≤ 1.2 1.2 ＜ ap ≤ 5 0.1 ＜ ap ≤ 1.2 1.2 ＜ ap ≤ 5
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.15 0.55 0.10 0.30 0.15 0.60 0.10 0.32
<950 <280

P 700-950 200-280
Alloyed steel 950-1200 280-355 0.12 0.50 0.08 0.28 0.12 0.55 0.08 0.30
1200-1400 355-415
Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.10 0.45 0.08 0.25 0.10 0.50 0.08 0.28
Precipitation-hardening stainless steel 1013 300
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 5.00 - - - - - - - -

Malleable cast iron 800 250
Fe-based alloy 943 280
Co-based alloy 1076 320
S 0.10 0.40 0.08 0.25 - - - -
Ni-based alloy 1177 350
Ti-alloy 1262 370
Aluminum 260 75
N Aluminum alloy 447 130
- - - - - - - -

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

199
 Milling

APM00-RO12
Profile milling cutter

d1
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-032-Z03-C32R-RO12-L120-C 32 32 120 40 6 3 RO 1204

d1
l1

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-040-Z04-M16R-RO12-C 40 M16 70 43 6 4 RO 1204

d1

L
D

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-040-Z04-A16R-RO12-C 40 16 40 - 6 4

APM00-050-Z05-A22R-RO12-C 50 22 40 - 6 5
RO 1204
APM00-063-Z06-A22R-RO12-C 63 22 40 - 6 6

APM00-080-Z07-A27R-RO12-C 80 27 50 - 6 7

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ32-80 4.0Nm

SP040085H DT-TP10

Note: With internal coolant

Without internal coolant

P310 P224 P248

200
Milling

Dimension(mm) Grade

AP403M
AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code
IC S

ROHT 1204M4E-MM3 12 4.76 ● ●

ROHT 1204M6E-MM3 12 4.76 ● ●

ROMT 1204M6E-MR6 12 4.76 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

RO..1204..
Geometry

Tensile MM3 MR6

Material Hardness ap
ISO strength fz
classification (HB)
( N/mm2 ) 0.1 ＜ ap ≤ 1.5 1.5 ＜ ap ≤ 6 0.1 ＜ ap ≤ 1.5 1.5 ＜ ap ≤ 6
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.18 0.60 0.12 0.32 0.18 0.65 0.12 0.35
<950 <280

P 700-950 200-280
Alloyed steel 950-1200 280-355 0.15 0.55 0.10 0.30 0.15 0.60 0.10 0.32
1200-1400 355-415
Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.12 0.50 0.10 0.28 0.12 0.55 0.10 0.30
Precipitation-hardening stainless steel 1013 300
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 6.00 - - - - - - - -

Malleable cast iron 800 250
Fe-based alloy 943 280
Co-based alloy 1076 320
S 0.12 0.45 0.10 0.28 - - - -
Ni-based alloy 1177 350
Ti-alloy 1262 370
Aluminum 260 75
N Aluminum alloy 447 130
- - - - - - - -

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

201
 Milling

APM00-RO16
Profile milling cutter
d1

L
D

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-063-Z05-A22R-RO16-C 63 22 40 - 8 5

APM00-080-Z06-A27R-RO16-C 80 27 50 - 8 6 RO 1605

APM00-100-Z07-A32R-RO16-C 100 32 50 - 8 7

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ63-100 5.0Nm

SP050120 DT-TP20

Note: With internal coolant

Without internal coolant

P310 P224 P248

202
Milling

Dimension(mm) Grade

AP403M
AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code
IC S

ROHT 1605M8E-MM3 16 5.56 ● ●

ROMT 1605M6E-MR6 16 5.56 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

RO..1605..
Geometry

Tensile MM3 MR6

Material Hardness ap
ISO strength fz
classification (HB)
( N/mm2 ) 0.1 ＜ ap ≤ 1.5 1.5 ＜ ap ≤ 8 0.1 ＜ ap ≤ 1.5 1.5 ＜ ap ≤ 8
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.20 0.65 0.12 0.35 0.20 0.68 0.12 0.38
<950 <280

P 700-950 200-280
Alloyed steel 950-1200 280-355 0.18 0.60 0.10 0.32 0.18 0.65 0.10 0.35
1200-1400 355-415
Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.15 0.55 0.10 0.30 0.15 0.58 0.10 0.32
Precipitation-hardening stainless steel 1013 300
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 8.00 - - - - - - - -

Malleable cast iron 800 250
Fe-based alloy 943 280
Co-based alloy 1076 320
S 0.15 0.50 0.10 0.30 - - - -
Ni-based alloy 1177 350
Ti-alloy 1262 370
Aluminum 260 75
N Aluminum alloy 447 130
- - - - - - - -

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

203
 Milling

APM00-RO20
Profile milling cutter
d1

L
D

Product code D d1 L l1 apmax Internal coolant Z Inserts

APM00-100-Z06-A32R-RO20-C 100 32 50 - 10 6

APM00-125-Z07-A40R-RO20-C 125 40 63 - 10 7 RO 2006

APM00-160-Z08-A40R-RO20 160 40 6 - 10 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ100-160 7.0Nm

SP060121 DT-TP25

Note: With internal coolant

Without internal coolant

P310 P224 P248

204
Milling

Dimension(mm) Grade

AP403M
AP301U

AC301P

AP351U

AP401U

AP351K

AP403S
Product code
IC S

ROHT 2006M8E-MM3 20 6.35 ● ●

ROMT 2006M8E-MR6 20 6.35 ● ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

RO..2006..
Geometry

Tensile MM3 MR6

Material Hardness ap
ISO strength fz
classification (HB)
( N/mm2 ) 0.1 ＜ ap ≤ 2.5 2.5 ＜ ap ≤ 10 0.1 ＜ ap ≤ 2.5 2.5 ＜ ap ≤ 10
(mm)
min max min max min max min max min max
<600 <180
Unalloyed steel 0.20 0.70 0.15 0.38 0.20 0.80 0.15 0.40
<950 <280

P 700-950 200-280
Alloyed steel 950-1200 280-355 0.18 0.65 0.12 0.35 0.18 0.70 0.12 0.38
1200-1400 355-415
Duplex stainless steel 778 230

M Austenitic stainless steel 675 200 0.15 0.60 0.12 0.32 0.15 0.65 0.12 0.35
Precipitation-hardening stainless steel 1013 300
Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 10.00 - - - - - - - -

Malleable cast iron 800 250
Fe-based alloy 943 280
Co-based alloy 1076 320
S 0.15 0.55 0.12 0.32 - - - -
Ni-based alloy 1177 350
Ti-alloy 1262 370
Aluminum 260 75
N Aluminum alloy 447 130
- - - - - - - -

Hardened steel - 50-60HRC

H Chilled cast iron - 55HRC
- - - - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

205
 Milling

AHM20-LN06
20° Approach angle high feed milling cutter

D M d1

apmax

l1

Product code D d1 L L1 M apmax Internal coolant Z Inserts

AHM20-016-Z02-M08R-LN06-C 16 14.5 42 25 M8 0.8 2

AHM20-017-Z02-M08R-LN06-C 17 14.5 42 25 M8 0.8 2

AHM20-020-Z03-M10R-LN06-C 20 18 51 30 M10 0.8 3

AHM20-021-Z03-M10R-LN06-C 21 18 51 30 M10 0.8 3

AHM20-025-Z04-M12R-LN06-C 25 23 59 35 M12 0.8 4

AHM20-026-Z03-M12R-LN06-C 26 23 59 35 M12 0.8 3

LN..0604
AHM20-026-Z04-M12R-LN06-C 26 23 59 35 M12 0.8 4

AHM20-032-Z04-M16R-LN06-C 32 29 70 43 M16 0.8 4

AHM20-032-Z05-M16R-LN06-C 32 29 70 43 M16 0.8 5

AHM20-033-Z05-M16R-LN06-C 33 29 70 43 M16 0.8 5

AHM20-035-Z05-M16R-LN06-C 35 29 70 43 M16 0.8 5

AHM20-040-Z06-M16R-LN06-C 40 29 70 43 M16 0.8 6

D d1

apmax

l1

Product code D d1 L L1 d2 apmax Internal coolant Z Inserts

AHM20-016-Z02-C16R-LN06-L100-C 16 16 100 30 - 0.8 2

AHM20-017-Z02-C16R-LN06-L150-C 17 16 150 25 - 0.8 2

AHM20-020-Z03-C20R-LN06-L130-C 20 20 130 50 - 0.8 3

AHM20-021-Z03-C20R-LN06-L160-C 21 20 160 30 - 0.8 3

AHM20-025-Z03-C25R-LN06-L140-C 25 25 140 60 - 0.8 3 LN..0604

AHM20-026-Z03-C25R-LN06-L180-C 26 25 180 35 - 0.8 3

AHM20-032-Z04-C32R-LN06-L150-C 32 32 150 70 - 0.8 4

AHM20-033-Z04-C32R-LN06-L200-C 33 32 200 35 - 0.8 4

AHM20-035-Z05-C32R-LN06-L200-C 35 32 200 35 - 0.8 5

Note: With internal coolant

Without internal coolant

P310 P224 P248

206
Milling

d1

D apmax

Product code D d1 L L1 d2 apmax Internal coolant Z Inserts

AHM20-040-Z06-A16R-LN06-C 40 16 40 - - 0.8 6
AHM20-050-Z07-A22R-LN06-C 50 22 40 - - 0.8 7
LN..0604
AHM20-052-Z07-A22R-LN06-C 52 22 40 - - 0.8 7
AHM20-063-Z08-A22R-LN06-C 63 22 40 - - 0.8 8

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ16-63 1.0Nm

Milling cutters
SP02506450H DT-TP08

Dimension(mm) Grades

AP403M

AW100K
Insert corner

AP151H
AC301P

AP301U

AP351U

AP401U

AC301K

AP351K

AP403S
Product code Wiper length
radius
mm
mm

LNMX 060410R-MM3 1.0 - ● ● ● ●

LNMX 060410R-MM4 1.0 - ● ● ● ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

LNMX..0604..
High feed Milling Plunging Milling
Material Tensile strength Hardness
ISO ap fz ae fz
classification ( N/mm2 ) (HB)
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.30 1.00 0.08 0.15
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.30 1.00 0.06 0.12

1200-1400 355-415

Duplex stainless steel 778 230

0.25 0.80
M Austenitic stainless steel 675 200 0.06 0.12

Precipitation-hardening stainless steel 1013 300 0.25 0.60

Grey cast iron 700 220

K Nodular cast iron 880 260 0.30 0.8 0.30 1.00 0.50 4 0.08 0.15

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.25 0.60 0.06 0.10
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130
-
Hardened steel 50-60HRC
H Chilled cast iron -
55HRC
0.25 0.60 0.06 0.10

Note: Please refer to P330 for programming information of high feed milling cutter
*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248
207
 Milling

AHM15-XD09
15° Approach angle high feed milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AHM15-025-Z02-W25R-XD09-C 25 25 96 40 1.5 2
XD..0904
AHM15-032-Z03-W32R-XD09-C 32 32 100 40 1.5 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AHM15-025-Z02-C25R-XD09-C 25 25 200 50 1.5 2

AHM15-026-Z02-C25R-XD09-L180-C 26 25 180 30 1.5 2 XD..0904

AHM15-032-Z03-C32R-XD09-C 32 32 250 70 1.5 3

Product code D d1 L l1 apmax Internal coolant Z Inserts

AHM15-040-Z03-A16R-XD09-C 40 16 32 - 1.5 3

AHM15-040-Z04-A16R-XD09-C 40 16 32 - 1.5 4

AHM15-040-Z05-A16R-XD09-C 40 16 32 - 1.5 5 XD..0904

AHM15-050-Z05-A22R-XD09-C 50 22 40 - 1.5 5

AHM15-050-Z06-A22R-XD09-C 50 22 40 - 1.5 6

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ25-50 3.0Nm

SP035084 DT-TP10

Note: Please refer to P330 for programming information of high feed milling cutter
Note: With internal coolant

Without internal coolant

P310 P224 P248

208
Milling

Dimension(mm) Grades

AW100K
Insert corner

AC301P

AP301U

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

XDLT 090408ER-MM3 0.8 1.3 ●

XDMW 090408ER-HR2 0.8 1.3 ●

Milling cutters
Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

XD..0904..
High feed Milling Plunging Milling
Material Tensile strength Hardness
ISO ap fz ae fz
classification ( N/mm2 ) (HB)
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.30 1.50 0.05 0.15
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.30 1.50 0.05 0.12

1200-1400 355-415

Duplex stainless steel 778 230

0.20 0.80 0.05 0.10
M Austenitic stainless steel 675 200

Precipitation-hardening stainless steel 1013 300 0.10 0.40 0.05 0.08

Grey cast iron 700 220

K Nodular cast iron 880 260 0.20 1.50 0.30 1.50 0.00 7 0.05 0.15

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.10 0.50 0.05 0.10
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130
-
Hardened steel 50-60HRC
H Chilled cast iron -
55HRC
0.30 1.00 0.05 0.10

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

209
 Milling

AHM15-XD12
15° Approach angle high feed milling cutter

Product code D d1 L l1 apmax Internal coolant Z Inserts

AHM15-032-Z02-C32R-XD12-C 32 32 250 70 2.5 2 XD..1205

Product code D d1 L l1 apmax Internal coolant Z Inserts

AHM15-052-Z03-A22R-XD12-C 52 22 40 - 2.5 3

AHM15-052-Z04-A22R-XD12-C 52 22 40 - 2.5 4

AHM15-052-Z05-A22R-XD12-C 52 22 40 - 2.5 5

AHM15-063-Z04-A22R-XD12-C 63 22 40 - 2.5 4

AHM15-063-Z05-A22R-XD12-C 63 22 40 - 2.5 5

AHM15-063-Z04-60A22R-XD12-C 63 22 40 - 2.5 4

AHM15-063-Z05-60A22R-XD12-C 63 22 40 - 2.5 5

AHM15-066-Z04-A27R-XD12-C 66 27 45 - 2.5 4

AHM15-066-Z05-A27R-XD12-C 66 27 45 - 2.5 5

AHM15-066-Z04-63A27R-XD12-C 66 27 45 - 2.5 4

AHM15-066-Z05-63A27R-XD12-C 66 27 45 - 2.5 5

AHM15-080-Z05-A27R-XD12-C 80 27 50 - 2.5 5 XD..1205

AHM15-080-Z08-A27R-XD12-C 80 27 50 - 2.5 8

AHM15-080-Z05-76A27R-XD12-C 80 27 50 - 2.5 5

AHM15-080-Z08-76A27R-XD12-C 80 27 50 - 2.5 8

AHM15-100-Z06-A32R-XD12-C 100 32 50 - 2.5 6

AHM15-100-Z09-A32R-XD12-C 100 32 50 - 2.5 9

AHM15-100-Z06-96A32R-XD12-C 100 32 50 - 2.5 6

AHM15-100-Z09-96A32R-XD12-C 100 32 50 - 2.5 9

AHM15-125-Z08-A40R-XD12-C 125 40 63 - 2.5 8

AHM15-125-Z11-A40R-XD12-C 125 40 63 - 2.5 11

AHM15-125-Z08-100A40R-XD12-C 125 40 63 - 2.5 8

AHM15-125-Z11-100A40R-XD12-C 125 40 63 - 2.5 11

Note: With internal coolant

Without internal coolant

P310 P224 P248

210
Milling

Dimension(mm) Spare parts

Cutter diameter Screw Wrench Torque

φ32-125 3.5Nm

SP040112 DT-TP15

Note: Please refer to P330 for programming information of high feed milling cutter

Dimension(mm) Grades

Milling cutters
AW100K
Insert corner

AC301P

AP301U

AP351U

AP401U

AC301K

AP351K
Product code Wiper length
radius
mm
mm

XDLT 120508ER-MM3 0.8 2.2 ● ● ● ● ●

XDLT 120512ER-MM3 1.2 2.2 ● ● ● ● ●

XDMW 120508ER-HR2 0.8 2.2 ● ●

Marked：● Stock available ○ Non-stocked standard

Materials Cutting depth and feed

XD..1205..
High feed Milling Plunging Milling
Material Tensile strength Hardness
ISO ap fz ae fz
classification ( N/mm2 ) (HB)
(mm)
min max min max min max min max
<600 <180
Unalloyed steel 0.30 2.00 0.06 0.18
<950 <280

P 700-950 200-280

Alloyed steel 950-1200 280-355 0.30 2.00 0.06 0.15

1200-1400 355-415

Duplex stainless steel 778 230

0.20 1.00 0.06 0.12
M Austenitic stainless steel 675 200

Precipitation-hardening stainless steel 1013 300 0.10 0.60 0.05 0.10

Grey cast iron 700 220

K Nodular cast iron 880 260 0.50 2.50 0.30 2.00 0.00 10 0.06 0.18

Malleable cast iron 800 250

Fe-based alloy 943 280

Co-based alloy 1076 320

S 0.30 2.00 0.05 0.12
Ni-based alloy 1177 350

Ti-alloy 1262 370

Aluminum 260 75
N - - - -
Aluminum alloy 447 130
-
Hardened steel 50-60HRC
H Chilled cast iron -
55HRC
0.30 1.00 0.05 0.12

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece
clamping and coolants. calculate for

P248

211
 Milling

Milling Insert Denomination System

A P F W
1 2 3 4

1- Shape/code 2- Clearance angle

A H M O R C D E F

S T Z X G N P O

Special Other clearance

angle
60° 86°

3- Tolerance

Shape：C, E, H, M, O, P, S, T, R, W
d m
IC
J,K,L,M,N U M, N U

4.76 ± 0,05 ± 0,08 ± 0,08 ± 0,13

In.Circle dimension Nose height Thickness 5.56 ± 0,05 ± 0,08 ± 0,08 ± 0,13
Class Unit
d m s
6 ± 0,05 ± 0,08 ± 0,08 ± 0,13
A mm ± 0,025 ± 0,005 ± 0,025
6.35 ± 0,05 ± 0,08 ± 0,08 ± 0,13
C mm ± 0,025 ± 0,013 ± 0,025
7.94 ± 0,05 ± 0,08 ± 0,08 ± 0,13
E mm ± 0,025 ± 0,025 ± 0,025
8 ± 0,05 ± 0,08 ± 0,08 ± 0,13
F mm ± 0,013 ± 0,005 ± 0,025
9.525 ± 0,05 ± 0,08 ± 0,08 ± 0,13
G mm ± 0,025 ± 0,025 ± 0,13
10 ± 0,05 ± 0,08 ± 0,08 ± 0,13
H mm ± 0,013 ± 0,013 ± 0,025
12 ± 0,08 ± 0,13 ± 0,13 ± 0,2
J mm * ± 0,005 ± 0,025
12.7 ± 0,08 ± 0,13 ± 0,13 ± 0,2
K mm * ± 0,013 ± 0,025
15.875 ± 0,1 ± 0,18 ± 0,15 ± 0,27
L mm * ± 0,025 ± 0,025
16 ± 0,1 ± 0,18 ± 0,15 ± 0,27
M mm * * ± 0,127
19.05 ± 0,1 ± 0,18 ± 0,15 ± 0,27
U mm * * ± 0,127
20 ± 0,1 ± 0,18 ± 0,15 ± 0,27
N mm * * ± 0,025
25 ± 0,13 ± 0,25 ± 0,18 ± 0,38
* For details refer to right and below tables
25.4 ± 0,13 ± 0,25 ± 0,18 ± 0,38

31.75 ± 0,15 ± 0,25 ± 0,2 ± 0,38

32 ± 0,15 ± 0,25 ± 0,2 ± 0,38

M&N shape D shape V shape 4- Clamping type

IC d m d m
A B C F G
5.56 ± 0,05 ± 0,11

6.35 ± 0,05 ± 0,11 ± 0,05 ± 0,16

7.94 ± 0,05 ± 0,11 ± 0,05 ± 0,16 H J M N Q

9.525 ± 0,05 ± 0,11 ± 0,05 ± 0,16

70°-90°
12.7 ± 0,08 ± 0,15 ± 0,08 ± 0,2 R T U W X
15.875 ± 0,10 ± 0,18 ± 0,10 ± 0,27
Special
19.05 ± 0,10 ± 0,18 ± 0,10 ± 0,27

212
Milling

16 04 PD S R - FM2
5 6 7 8 9 - 10
5- Cutting edge length 6- Insert thickness

In.Circle
dimension H M O R S T Z
(mm)
01=1.59mm
L L L L L L L
T1=1.98mm
3.180 05
02=2.38mm
3.970 06

5.000 05
T2=2.78mm

5.560 09 03=3.18mm
6.000 06 T3=3.97mm
6.350 11 04=4.76mm
7.940 13
05=5.56mm
8.000 08
06=6.35mm

Milling inserts
9.525 09 09 16
07=7.94mm
10.000 10
09=9.52mm
12.000 12

12.700 04 12 12 22

15.875 15 15 27

16.000 06 16
8- Edge preparation
19.050 19 19 33

20.000 20 F E T
25.000 25 25

25.400 25

31.750 31
Sharp cutting edge Honed cutting edge Negative land

32.000 32
K S P

7-Corner radius and wiper edge

Double negative Negative land Double negative

00 = sharp 24 = 2.4 land +honed land +honed
R 01 = 0.1 28 = 2.8
02 = 0.2 32 = 3.2
04 = 0.4 40 = 4.0
08 = 0.8 48 = 4.8 9-Hand of tool
12 = 1.2 56 = 5.6
16 = 1.6 64 = 6.4
20 = 2.0 X = others R L N
Round insert:MO refers to metric dia. size

1 2
Kr

2 Clearance angle of wiper edge

αn

(n)
A = 3° Right hand Left hand Neutral
1 Approach angle(Entering angle)
B = 5°
(kr)
C = 7°
A = 45°
D = 15°
D = 60°
E = 20°
E = 75°
F = 25°
F = 85° 10-Chip breakers refers to page P258
G = 30°
P = 90°
N = 0°
Z = Others
P = 11° Marked: if it has corner radius, the information needs to put between
Z = Others thickness and wipers.
Example: APET 160408PDFR-FM2

213
 Milling

Geometry Application Guide

Milling geometry application table

Materials
FM2 MM3 MM4 MR2 MR6 RR2 HR2

Suitable for
Tensile Light Heavy
Material Hardness machining General Medium Roughing Roughing
ISO strength cutting roughing
classification (HB) aluminium purpose machining machining machining
(N/mm2) machining machining
alloy
<600 <180 - ◐ ● ● ● - -
Unalloyed steel
<950 <280 - ◐ ● ● ● - -

P 700-950 200-280 - ◐ ● ● ● - -

Alloyed steel 950-1200 280-355 - ◐ ● ● ● - -

1200-1400 355-415 - ◐ ● ● ● - -

Duplex stainless
778 230 - ◐ ● ◐ - - -
steel
Austenitic
675 200 - ◐ ● ◐ - - -
stainless steel
M
Precipitation-
hardening 1013 300 - ◐ ● ◐ - - -
stainless steel

Grey cast iron 700 220 - - ◐ ● ● ● ●

K Nodular cast iron 880 260 - - ◐ ● ● ● ●

Malleable cast iron 800 250 - - ◐ ● ● ● ●

Fe-based alloy 943 280 - ● ◐ ◐ - - -

Co-based alloy 1076 320 - ● ◐ ◐ - - -

S
Ni-based alloy 1177 350 - ● ◐ ◐ - - -

Ti-alloy 1262 370 - ● ◐ ◐ - - -

Aluminum 260 75 ● - - - - - -
N
Aluminum alloy 447 130 ● - - - - - -

◐ ●
-
Hardened steel 50-60HRC - - - - -
H
◐ ●
-
Chilled cast iron 55HRC - - - - -

● Best choice
◐ 2nd choice
- Inapplicable

214
Milling

Milling Geometry Introduction

Insert geometry Edge shape Application

▪ Low cutting force, for weak machining condition

FM2 ▪ Sharp geometry
▪ For aluminium material machining

▪ Low cutting force, for weak machining condition

MM3 ▪ Sharp geometry
▪ For steel, stainless-steel and heat resistant alloy machining.

▪ For medium machining condition

MM4 ▪ Universal geometry
▪ For machining most materials

▪ For medium or better machining condition

MR2 ▪ Universal geometry
▪ For machining most materials

Milling inserts
▪ For stable machining condition
MR6 ▪ Roughing geometry
▪ For machining most materials

▪ For stable machining condition

HR2 ▪ Roughing geometry
▪ Mainly for cast iron machining

▪ For stable machining condition

RR2 ▪ Heavy roughing geometry
▪ Mainly for cast iron and steel machining

IT ▪ Sharp geometry, for specified product

DT ▪ Universal geometry, for specified product

215
 Milling

Grade Application Guide

Milling grade ISO group

Material PVD PVD PVD PVD PVD PVD CVD CVD PVD PVD Uncoated
Materials ISO ISO
Group AP301U AP351U AP351M AP401U AP403S AP403M AC301P AC301K AP351K AP151H AW100K
P01 P01
P05 P05
P10 P10
P15 P15
Unalloyed P20 P20
steels /
P Alloyed
P25 AP301U P25
steels P30 P30
AC301P
P35 AP351M P35
AP351U
P40 AP401U P40
AP403M
P45 P45
P50 P50
M01 M01
M05 M05
M10 M10
M15 M15
M20 M20
Stainless
M steels
M25 AP301U M25
M30 M30
AC301P
M35 AP351M M35
AP351U
M40 AP401U M40
AP403S AP403M
M45 M45
M50 M50
K01 K01
K05 K05
K10 K10
K15 AP151H K15
K20 K20
K Cast iron K25
AC301K
AP351K
K25
K30 K30
K35 K35
K40 K40
K45 K45
K50 K50
S01 S01
S05 S05
S10 S10
S15 S15
Heat S20 S20
S resistant S25 S25
alloys S30 S30
S35 AP351M S35
AP351U
S40 AP401U S40
AP403S AP403M
S45 S45
S50 S50
N01 N01
N05 N05
Aluminum/ N10 N10
N Aluminum N15
alloys
AW100K N15
N20 N20
N25 N25
N30 N30
H01 H01
H05 H05
Hardened H10 H10
steels/
H Chilled cast
H15 AP151H H15
iron H20 H20
H25 H25
H30 H30

216
Milling

Grade Application Guide

Milling grade application

Materials
PVD coated CVD coated PVD coated Uncoated

Tensile

AP351M

AP403M

AW100K
AP151H
AP301U

AP351U

AP401U

AC301P

AC301K

AP351K
AP403S
Material Hardness
ISO strength
classification (HB)
(N/mm2)

<600 <180 ● ● ● ◐ ◐ ● ● ◐ - - -

Unalloyed steel
<950 <280 ● ● ● ◐ ◐ ● ● ◐ - - -

P 700-950 200-280 ● ● ● ◐ ◐ ● ● ◐ - - -

Alloyed steel 950-1200 280-355 ● ● ● ◐ ◐ ● ● ◐ - - -

1200-1400 355-415 ● ● ● ◐ ◐ ● ● ◐ - - -

Duplex stainless steel 778 230 ◐ ● ● ● ● ● ◐ - - - -

Milling inserts
M Austenitic stainless steel 675 200 ◐ ● ● ● ● ● ◐ - - - -

Precipitation-hardening
1013 300 ◐ ● ● ● ● ● ◐ - - - -
stainless steel

Grey cast iron 700 220 - - - - - - - ● ● ● -

K Nodular cast iron 880 260 - - - - - - - ● ● ● -

Malleable cast iron 800 250 - - - - - - - ● ● ● -

Fe-based alloy 943 280 - ◐ ● - ● ● - - - - -

Co-based alloy 1076 320 - ◐ ● - ● ● - - - - -

S
Ni-based alloy 1177 350 - ◐ ● - ● ● - - - - -

Ti-alloy 1262 370 - ◐ ● - ● ● - - - - ◐

Aluminum 260 75 - - - - - - - - - - ●

N
Aluminum alloy 447 130 - - - - - - - - - - ●

●
-
Hardened steel 50-60HRC - - - - - - - - - -

H
●
-
Chilled cast iron 55HRC - - - - - - - - - -

● Best choice
◐ 2nd choice
- Inapplicable

217
 Milling

Milling Grade Description

AP301U

Coating: PVD coating

Suitable for steel, stainless steel and high-temp alloy milling. High strength and wear
resistance. Ultra fine carbide substrate with nanostructured PVD coating in controllable
layer, high coating adhesion, wear-resistance and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP301U
M AP301U
K

Remark: Best choice

2nd choice

AP351U

Coating: PVD coating

Suitable for steel, stainless steel and high-temp alloy semi-finishing and roughing milling.
High strength carbide substrate with nanostructured PVD coating in controllable layer, high
coating adhesion, wear-resistance and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP351U
M AP351U
K

S AP351U
N

Remark: Best choice

2nd choice

218
Milling

AP401U

Coating: PVD coating

Suitable for steel, stainless steel and high-temp alloy rough milling. Ultra high strength
carbide substrate with nanostructured PVD coating in controllable layer, high coating
adhesion, wear-resistance and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP401U
M AP401U
K

S AP401U

Milling inserts
N

Remark: Best choice

2nd choice

AC301P

Coating: CVD coating

Suitable for steel and stainless steel semi-finish milling. High strength carbide substrate
with multi-layer CVD coating, high coating adhesion, wear resistance and surface finish
quality.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AC301P
M AC301P
K

Remark: Best choice

2nd choice

219
 Milling

AC301K

Coating: CVD coating

Suitable for gray and nodular cast iron finish, semi-finish and rough milling. High strength
and wear resistance carbide substrate with multi-layer CVD coating, controllable coating
layer structure and high adhesive strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P

K AC301K
S

Remark: Best choice

AP351K

Coating: PVD coating

Suitable for nodular cast iron, finish, semi-finishand rough milling. High strength and wear
resistance carbide substrate with nanostructured PVD coating in controllable layer, high
coating adhesion, wear resistance and oxidation resistance.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P

K AP351K
S

Remark: Best choice

220
Milling

AW100K

Coating: Uncoated
Uncoated fine grain carbide substrate with special treated cutting edge. Suitable for
nonferrous metal milling under various cutting conditions.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P

Milling inserts
N AW100K
H

Remark: Best choice

AP351M

Coating: PVD Coating

Suitable for steel, stainless-steel and heat resistant alloy milling, with excellent thermal-
stability and wear-resistant, good thermal-crack resistance and high coating adhesion.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP351M
M AP351M
K

S AP351M
N

Remark: Best choice

221
 Milling

AP403M

Coating: PVD Coating

Suitable for steel, stainless-steel and heat resistant alloy milling, with good wear-
resistance, heat-resistance and high coating adhension, very smooth coating surface.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP403M
M AP403M
K

S AP403M
N

Remark: Best choice

AP403S

Coating: PVD Coating

Suitable for stainless-steel and heat resistant alloy milling, with new substrate and coating
combination, new substrate with high toughness, excellent hot hardness. New generation
of PVD coating, with high hardness, high wear-resistance, good performance on heat-
conductivity, thermal-stability, smooth surface good for reducing built-up edge.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P

M AP403S
K

S AP403S
N

Remark: Best choice

222
Milling

AP151H

Coating: PVD Coating

Suitable for hardened steel milling and cast iron finish milling. Ultra fine carbide substrate
with high hardness and wear-resistance. Extremely hard PVD coating with good oxidation
resistance, wear resistance, and thermal crack resistance.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P

Milling inserts
N

H AP151H

Remark: Best choice

223
 Milling

OD..04/06
Positive octagonal milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l d s r b

ODET 0404APFN-FM2 4 12.7 4.76 - 1.2 ●

ODET 0605APFN-FM2 6 16 5.56 - 1.6 ●

ODHT 0404APEN-MM3 4 12.7 4.76 - 1.2 ● ● ● ● ●

ODMT 040408EN-MM3 4 12.7 4.76 0.8 - ● ●

ODMT 060508EN-MM3 6 16 5.56 0.8 - ● ● ● ● ● ●

ODMT 060512EN-MM3 6 16 5.56 1.2 - ●

ODHT 0605APEN-MM3 6 16 5.56 - 1.6 ● ● ● ● ●

ODEW 0404APSR-HR2 4 12.7 4.76 - 1.2 ● ● ●

ODEW 0605APSR-HR2 6 16 5.56 - 1.6 ● ●

ODEW 0605APSN-HR2 6 16 5.56 - 1.6 ●

ODMW 040408EN-HR2 4 12.7 4.76 0.8 - ● ●

ODMW 060512EN-HR2 6 16 5.56 1.2 - ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

224
Milling

ON..05
Negative octagonal milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l d s r b

ONHU 050408-MM3 4.00 12.70 4.76 0.8 - ●

ONMU 050408-MM4 4.00 12.70 4.76 0.8 - ● ● ● ● ●

Milling inserts
ONHU 050408AEN-MM3 4.00 12.70 4.76 0.8 0.7 ● ● ●

ONHU 050408AEN-MM4 4.00 12.70 4.76 0.8 0.7 ● ● ●

ONHU 0504ZNR-MM3 4.00 12.70 4.76 0.8 1.4 ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

225
 Milling

SC..09/12
Positive square milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s r b

SCMT 09T304EN-MM3 9.525 3.97 0.4 - ● ● ●

SCMT 120412EN-MM3 12.7 4.76 1.2 - ● ●

SCMT 12M512EN-MM3 12.7 5 1.2 - ● ●

SCHT 1204ACEN-MR6 12.7 4.76 - 1.5 ● ●

SCHT 12M5ACEN-MR6 12.7 5 - 1.5 ● ●

SCMW 12M512EN-HR2 12.7 5 1.2 - ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

226
Milling

SD..09/12
Positive square milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s r b

SDMT 09T304EN-MM3 9.525 3.97 0.4 - ● ● ● ●

SDMT 09T308EN-MM3 9.525 3.97 0.8 - ● ● ● ●

SDMT 09T320-MM4 9.525 3.97 2.0 - ●

Milling inserts
SDMT 120408EN-MM4 12.7 4.76 0.8 - ● ● ● ●

SDMT 120412EN-MM3 12.7 4.76 1.2 - ● ● ●

SDGT 09T3AEEN-MM4 9.525 3.97 - 1.5 ● ● ● ●

SDKT 1204AEEN-MR2 12.7 4.76 - 2.0 ● ● ● ● ●

SDGT 09T3PDER-MR6 9.525 3.97 0.8 1.2 ● ● ● ●

SDGT 1204PDER-MR6 12.7 4.76 0.8 1.6 ● ● ● ●

SDHT 1204AEEN-MR6 12.7 4.76 0.8 2.0 ● ● ● ●

SDMW 09T308EN-HR2 9.525 3.97 0.8 - ● ●

SDHW 09T3AESN-HR2 9.525 3.97 - 1.5 ● ● ●

SDMW 120412EN-HR2 12.7 4.76 1.2 - ● ● ●

SDHW 1204AESN-HR2 12.7 4.76 - 2.0 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

227
 Milling

SE..12
Positive square milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s r b

SEKT 1204AFER-MR2 12.7 4.91 1.2 1.8 ● ● ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

228
Milling

SNGX12/19
Negative short wiper milling inserts(applicable to AFM45-SN12/SN19 milling cutter)

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s b

SNHX 1206ANN-FM2 12.7 6.98 1.8 ●

SNGX 1206ANN-MM3 12.7 6.98 1.8 ● ● ● ● ●

SNGX 1206ANN-MM4 12.7 6.98 1.8 ● ● ● ● ●

Milling inserts
SNGX 1206ANN-MR6 12.7 6.98 1.8 ● ● ● ● ●

SNGX 1206ANN-RR2 12.7 6.98 1.8 ● ● ● ● ●

SNMX 1206ANN-MM3 12.7 6.98 1.8 ● ● ● ● ●

SNMX 1206ANN-MM4 12.7 6.98 1.8 ● ● ● ● ●

SNMX 1206ANN-MR6 12.7 6.98 1.8 ● ● ● ● ●

SNGX 1909ANN-MM3 19.05 9.52 2.9 ●

SNGX 1909ANN-MR6 19.05 9.52 2.9 ●

SNHX12
Negative long wiper milling inserts(applicable to AFM45-SN12 milling cutter)

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K

l s b

SNHX 1206ANN-W 12.7 6.98 6.7 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

229
 Milling

SNGX12
Negative short wiper milling inserts(applicable to AFM75-SN12 milling cutter)

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s b

SNGX 1206ENN-MM3 12.7 6.98 1.2 ● ● ● ● ●

SNGX 1206ENN-MM4 12.7 6.98 1.2 ● ● ● ● ●

SNGX 1206ENN-MR6 12.7 6.98 1.2 ● ● ● ● ●

SNMX 1206ENN-MM4 12.7 6.98 1.2 ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

230
Milling

SNGX12
Negative short wiper milling inserts(applicable to AFM88-SN12 milling cutter)

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s b

SNHX 1206ZNN-FM2 12.7 7.63 0.8 ●

SNGX 1206ZNN-MM4 12.7 6.98 1.2 ● ● ● ● ●

SNGX 1206ZNN-MR6 12.7 6.98 1.2 ● ● ● ● ●

Milling inserts
SNGX 1206ZNN-MM3 12.7 6.98 1.2 ● ● ● ● ●

SNHX12
Negative long wiper milling inserts(applicable to AFM88-SN12 milling cutter)

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K

l s b

SNHX 1206ZNN-W 12.7 6.98 4.4 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

231
 Milling

SN.X12
Negative square milling inserts with corner radius

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l s r b

SNGX 120608-MM4 12.7 6.98 0.8 - ● ● ● ● ●

SNGX 120612-MM4 12.7 6.98 1.2 - ●

SNMX 120608-MM4 12.7 6.98 0.8 - ● ● ● ● ●

SNMX 120612-MM3 12.7 6.98 1.2 - ● ● ● ● ●

SNMX 120612-MM4 12.7 6.98 1.2 - ● ● ● ● ●

SNMX 120612-MR6 12.7 6.98 1.2 - ● ● ● ● ●

SNMX 120612-RR2 12.7 6.98 1.2 - ● ● ● ● ●

SNMX 120620-MM4 12.7 6.98 2.0 - ● ● ● ● ●

SNMX 120620-RR2 12.7 6.98 2.0 - ● ● ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

232
Milling

XN.U07/09ANN
Negative heptagonal milling inserts with short wiper

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l d s r b

XNGU 0705ANN-MM3 7.0 14.5 5.4 0.8 1.1 ● ● ●

Milling inserts
XNGU 0705ANN-MM4 7.0 14.5 5.4 0.8 1.1 ● ●

XNMU 0705ANN-MM4 7.0 14.5 5.4 0.8 1.1 ● ● ● ● ● ●

XNMU 0705ANN-MR6 7.0 14.5 5.4 0.8 1.1 ● ● ● ●

XNGU 0906ANN-MM3 9.2 19.0 6.25 0.8 1.4 ● ● ● ●

XNGU 0906ANN-MM4 9.2 19.0 6.25 0.8 1.4 ● ● ● ●

XNMU 0906ANN-MR6 9.2 19.0 6.25 0.8 1.4 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

233
 Milling

XN.U 07/09
Negative heptagonal milling inserts with corner radius

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K
l d s r b

XNMU 070508-MM4 7.0 14.5 5.40 0.8 - ● ● ● ●

XNMU 090612-MM4 9.2 19.0 6.25 1.2 - ● ● ● ● ●

XNGX 07/09ANN-W
Negative milling inserts with long wiper

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K

AP351K

l d s r b

XNGX 0705ANN-W - 15 5.4 1.0 6 ● ●

XNGX 0906ANN-W - 19.05 6.2 1.0 7.5 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

234
Milling

LNHU 0904
Nagative shoulder milling insert

l s

Dimension(mm) Grades

Inserts Product code

AP403M

AW100K
AP301U

AC301P

AP351U

AC301K

AP351K
l d s r b

LNHU 090404ER-FM2 9 4.5 7.5 0.4 - ●

LNHU 090404ER-MM3 9 4.5 7.5 0.4 - ● ●

LNHU 090404ER-MR2 9 4.5 7.5 0.4 - ● ● ● ● ●

LNHU 090408ER-MR2 9 4.5 7.45 0.8 - ● ● ● ● ●

Milling inserts
LNHU 090412ER-MR2 9 4.5 7.4 1.2 - ● ● ●

LNHU 090416ER-MR2 9 4.5 7.35 1.6 - ● ● ●

LNHU 090420ER-MR2 9 4.5 7.31 2 - ● ● ●

Wiper insert type

l s

d
r

Dimension(mm) Grades

Inserts Product code

AP403M

AW100K
AP301U

AC301P

AP351U

AC301K

AP351K

l d s r b

LNHU0904PDER-W 9.24 4.5 7.4 0.4 3.6 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

235
 Milling

LNHU 1306...
Nagative shoulder millng insert

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
l d s r b

LNHU 130608ER-FM2 13.02 6.8 10.11 0.8 - ●

LNHU 130608ER-MM3 13.02 6.8 10.19 0.8 - ●

LNHU 130608ER-MR2 13.02 6.8 10.15 0.8 - ● ● ● ● ● ●

LNHU 130612ER-MR2 13.02 6.8 10.09 1.2 - ● ● ●

LNHU 130616ER-MR2 13.02 6.8 10.03 1.6 - ● ● ●

LNHU 130620ER-MR2 13.02 6.8 9.99 2.0 - ● ●

LNHU 130624ER-MR2 13.02 6.8 9.92 2.4 - ● ●

LNHU 130631ER-MR2 13.02 6.8 9.83 3.1 - ● ● ●

b

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

l d s r b

LNHU 1306PDER-W 13.39 6.8 10.02 0.8 5.6 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

236
Milling

LNHU 1607..
Nagative shoulder milling insert

l s

Dimension(mm) Grades

Inserts Product code

AP403M

AW100K
AP301U

AC301P

AP351U

AC301K

AP351K
l d s r

LNHU 160708ER-MR2 16 7.2 13 0.8 ● ● ● ●

LNHU 160716ER-MR2 16 7.2 13 1.6 ● ●

Milling inserts
Marked：● Stock available ○ Non-stocked standard

P148 P248

237
 Milling

WN..08
Negative milling insert

Dimension(mm) Grades

Inserts Product code

AW100K

AP151H
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
l d s r

WNHU 080608R-FM2 8 12.5 7.88 0.8 ●

WNGU 080604R-MM3 8 12.5 7.88 0.4 ● ●

WNGU 080608R-MM3 8 12.5 7.88 0.8 ● ● ●

WNGU 080604R-MM4 8 12.5 7.88 0.4 ● ● ● ●

WNGU 080608R-MM4 8 12.5 7.88 0.8 ● ● ● ● ● ● ●

WNGU 080612R-MM4 8 12.5 7.88 1.2 ● ● ●

WNGU 080616R-MM4 8 12.5 7.88 1.6 ● ● ●

WNGU 080608R-MR2 8 12.5 7.88 0.8 ● ●

WNGU 080612R-MR2 8 12.5 7.88 1.2 ● ●

WNGU 080616R-MR2 8 12.5 7.88 1.6 ● ●

WNGU 08
Negative wiper milling insert

Dimension(mm) Grades

Inserts Product code

AW100K
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

d b s r

WNHX 0806ZZR-W 12.5 6.58 6.47 1 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

238
Milling

APKT 1003PDER-IT..
Positive shoulder milling insert

r
b s

Dimension(mm) Grades

Inserts Product code

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

AP403S
l d s r b

APKT 1003PDER-IT 11.35 6.66 3.77 0.8 1.08 ● ● ● ●

Milling inserts
Marked：● Stock available ○ Non-stocked standard

P148 P248

239
 Milling

APKT 1705..-DT..
Positive shoulder milling insert

r
b s

Dimension(mm) Grades

Inserts Product code

AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

AP403S
l d s r b

APKT 1705PER-DT 18.40 10.76 5.56 0.8 2.16 ● ● ● ● ● ●

APKT 170516R-DT 18.62 10.76 5.56 1.6 1.7 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

240
Milling

APMT..
Positive shoulder milling inserta

Dimension(mm) Grades

Inserts Product code

AP151H
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
l d s r b

APMT 1135PDER 11.31 6.26 3.5 0.8 1.25 ● ● ●

Milling inserts
APMT 1604PDER 17.32 9.37 5.17 0.8 1.54 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

241
 Milling

RPM ...MM4
Copy milling insert
s

Dimension(mm) Grades

Inserts Product code

AP351M
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K

AP403S
l b s r

RPM 080ER-MM4 14.76 6.89 3.21 8.0 ● ● ●

RPM 100ER-MM4 18.85 8.62 3.89 10 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

242
Milling

RD/RP
Round inserts

Dimension(mm) Grades

Inserts Product code

AP151H
AP301U

AC301P

AP351U

AP401U

AC301K

AP351K
d s

RDHT 0702MOE-MM3 7 2.38 ●

RDHT 1003MOE-MM3 10 3.18 ●

RDHT 12T3MOE-MM3 12 3.97 ● ● ●

Milling inserts
RDHT 1606MOE-MM3 16 6.35 ● ● ●

RDHT 1604MOE-MM3 16 4.76 ● ●

RDHW 0702MOS-HR2 7 2.38 ● ● ● ● ●

RDHW 1003MOS-HR2 10 3.18 ● ● ● ● ●

RDHW 12T3MOS-HR2 12 3.97 ● ● ● ● ●

RDHW 1606MOS-HR2 16 6.35 ● ●

RDMT 0702MOE-MM3 7 2.38 ● ●

RDMT 1003MOE-MM3 10 3.18 ● ● ●

RDMT 12T3MOE-MM3 12 3.97 ● ●

RDMT 1606MOE-MM3 16 6.35 ● ●

RDMT 1604MOE-MM3 16 4.76 ●

RDMW 1204MOE-HR2 12 4.76 ● ●

RDMW 1606MOE-HR2 16 6.35 ●

RPMW 1003MOE-HR2 10 3.18 ● ● ●

RPMW 10T3MOE-HR2 10 3.97 ● ● ●

RPMT 1204MOE 12 4.76 ● ● ●

Marked：● Stock available ○ Non-stocked standard

P248

243
 Milling

RO..T
Round inserts

d
s

11°

Dimension(mm) Grades

Inserts Product code

AP403M
AP301U

AC301P

AP351U

AC301K

AP351K

AP403S
d s

ROHT 0803M0E-MM3 8 3.18 ● ●

ROHT 10T3M8E-MM3 10 3.97 ● ●

ROHT 1204M4E-MM3 12 4.76 ● ●

ROHT 1204M6E-MM3 12 4.76 ● ●

ROHT 1605M8E-MM3 16 5.56 ● ●

ROHT 2006M8E-MM3 20 6.35 ● ●

ROMT 10T3M4E-MR6 10 3.97 ● ●

ROMT 1204M6E-MR6 12 4.76 ● ●

ROMT 1605M6E-MR6 16 5.56 ● ●

ROMT 2006M8E-MR6 20 6.35 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

244
Milling

LN..06
High feed milling inserts

r
s

Dimension(mm) Grades

Inserts Product code

AP403M

AW100K

AP151H
AC301P

AP301U

AP351U

AP401U

AC301K

AP351K

AP403S
l d s r

LNMX 060410R-MM3 10 6.35 3.6 1.0 ● ● ● ●

Milling inserts
LNMX 060410R-MM4N 10 6.35 3.6 1.0 ● ● ● ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

245
 Milling

XD..09/12
High feed milling inserts

Dimension(mm) Grades

Inserts Product code

AW100K
AC301P

AP301U

AP351U

AP401U

AC301K

AP351K
d s r b

XDLT 090408ER-MM3 9.525 4.76 0.8 1.3 ●

XDLT 120508ER-MM3 12.7 5.56 0.8 2.2 ● ● ● ● ●

XDLT 120512ER-MM3 12.7 5.56 1.2 2.2 ● ● ● ● ●

XDMW 090408ER-HR2 9.525 4.76 0.8 1.3 ●

XDMW 120508ER-HR2 12.7 5.56 0.8 2.2 ● ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

246
Milling

ON05/LN12/LN15
Cast iron finishing machining inserts

l s

Dimension(mm) Grades

Inserts Product code

AP151H
l d s r

ONHF 050408-MM3 5.3 12.7 4.76 0.8 ●

Milling inserts
h

LN12 r

d
Cast iron finishing wiper insert

l s

Dimension(mm) Grades

Inserts Product code

AP151H
l d s r h

LNHQ 120408FN-W 12.7 9.525 4.76 0.8 4.2 ●

LN15 h

Cast iron finishing wiper insert r

l s

Dimension(mm) Grades

Inserts Product code

AP151H

l d s r h

LNHQ 150416FN-W 15.875 9.525 4.76 1.6 4.2 ●

Marked：● Stock available ○ Non-stocked standard

P148 P248

247
 Milling

Cutting Parameter Recommendation Table

Materials
AP301U AC301P AP351U AP351M
PVD CVD PVD PVD
P15-P35 P25-40 P30-P45 P25-P45

Tensile strength
M15-M35 - M30-M45 M25-M45

Brinell hardness

Rm(N/mm²)
- - S30-S45 -
Material
ISO - - - S25-S45

(HB)
classification
- - - -
- - - -

1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1

C ≤ 0.25% Annealed 125 428 320 280 240 380 300 260 280 240 200
0.25 < C ≤ 0.55% Annealed 190 639 290 240 200 350 250 220 250 210 170
0.25 < C ≤ 0.55% Heat-treated 210 708 260 210 170 310 220 190 230 180 140
Unalloyed steel C > 0.55% Annealed 190 639 290 240 200 350 250 220 250 210 170
C > 0.55% Heat-treated 300 1013 210 170 130 250 170 150 160 130 100
Free cutting steel
Annealed 220 745 250 200 160 300 210 180 220 170 130
(short-chip)
Annealed 175 591 290 250 200 340 300 250 270 230 180
P Heat-treated 300 1013 250 210 160 290 250 200 230 190 140
Low-alloyed steel
Heat-treated 380 1282 230 190 140 250 210 160 210 170 120
Heat-treated 430 1477 190 150 110 210 170 130 170 130 90
High-alloyed steel Annealed 200 675 220 190 160 240 210 180 200 170 140
and
Hardened and tempered 300 1013 170 140 110 190 160 130 150 130 90
high-alloyed tool
steel Hardened and tempered 400 1361 150 120 90 160 130 100 130 100 70
Ferritic/martensitic, annealed 200 675 190 160 130 200 170 140 160 140 110 180 150 120
Stainless steel
Martensitic, heat-treated 330 1114 160 120 90 170 140 110 140 110 80 150 120 90
Austenitic, quench hardened 200 675 180 150 120 170 140 110 170 150 120
Austenitic, precipitation
300 1013 160 130 100 150 120 90 150 130 100
M Stainless steel hardened (PH)

Austenitic/ferritic, duplex 230 778 170 140 110 160 130 100 160 140 110

Ferritic 200 400

Malleable cast iron
Pearlitic 260 700
Low tensile strength 180 200
Grey cast iron
K High tensile strength/austenitic 245 350
Ferritic 155 400
Nodular cast iron
Pearlitic 265 700

* 此表仅显示通用切削条件，实际选用应根据机器刚性、刀体、工件的条件和冷却液等因素来调整。( hm= 平均铁屑厚度 )

GGV(CGI) 230 400

Wrought aluminium Non-aging 30 -

alloys Aged 100 340
≤ 12% Si, non-aging 75 260
Cast aluminium
≤ 12% Si, aged 90 310
alloys
N > 12% Si, non-aging 130 450

Magnesium alloys 70 250

Unalloyed, electrolytic copper 100 340

Copper and copper Brass, bronze, red brass 90 310

alloys Cu alloys, short-chipping 110 380
High-tensile, Ampco alloy 300 1010
Annealed 200 680 90 80 70 100 90 80
Fe-based
Hardened 280 940 75 60 50 80 70 60

Heat-resistant alloys Annealed 250 840 80 55 45 70 60 50

Ni or Co based Hardened 350 1180 60 50 35 60 50 40

S Cast 320 1080 60 55 40 65 55 45

Pure titanium 200 680 110 90 80 120 100 90

Titanium alloys α and β alloys, hardened 375 1260 50 40 30 55 45 35

β alloys 410 1400 50 40 30 55 45 35

Tungsten alloys 1177 300 1010 65 60 50 70 65 55
Molybdenum alloys 1262 300 1010 65 60 50 70 65 55
Hardened and tempered 50HRC
Hardened steel Hardened and tempered 55HRC
H Hardened and tempered 60HRC
Hardened cast steel Hardened and tempered 50HRC

248
Milling

Milling grade application range

AP403M AP401U AP403S AC301K AP351K AP151H AW100K
PVD PVD PVD CVD PVD PVD Uncoated
P35-P50 P30-P50 - - - - -
M35-M50 M30-M50 M35-M50 - - - -
- - - K10-K35 K15-K40 K15-K40 -
S35-S50 - S35-S50 - - - -
- - - - - - N10-N20
- - - H10-H20 - H10-H20 -
according to the value of ae/Dc
1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1 1/10 1/5 1/1
Cutting speed (m/min)

Milling inserts
170 140 110 160 140 110
140 110 80 140 110 80
160 140 110 160 140 110 190 160 140

140 120 90 150 130 90 170 140 120

150 130 100 150 130 100 160 130 110

240 210 180 220 190 160 180 150 120

220 190 160 200 170 140 160 130 100
280 250 220 260 230 200 210 180 150
240 210 180 210 190 160 180 150 120
260 230 200 240 210 180 190 160 130
190 160 130 170 140 110 150 120 90
200 170 140 180 150 120 160 130 100
2200 2200 2000
1800 1800 1600
600 600 500

500 500 400

280 280 200

400 400 300

300 300 250

200 200 160

95 85 75 110 100 90

80 65 55 90 80 70

85 60 50 80 70 60

65 55 35 75 65 50

65 60 45 75 65 55
120 95 85 120 100 90

50 40 30 60 50 40

50 40 30 60 50 40
70 60 50 70 65 60
70 60 50 70 65 60
70 60 50 65 55 45
60 50 40

60 50 40

249
Drilling

Drilling Holder Denomination System

HP -
2D -
255 -
S32 -
S07
1 2 3 4 5

1 HP Machining method Represent for high productivity machining

2 2D Length-diameter ratio 2D, 3D, 4D,

3 255 Tool diameter 255-25.5mm, 500-50mm

4 S32 Shank diameter S20=20mm S25=25mm S32=32mm S40=40mm

Inserts shape and edge If the insert shape is "S", it means the cutting edge length is 7mm, if the insert shape is "W", the
5 S07
length code is "W07"

Drilling holders

253
 Drilling

DP Series Drilling Holder Length-diameter ratio：2D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-2D130-S20-S05 13.0 29 99 20 50
HP-2D135-S20-S05 13.5 30 100 20 50
HP-2D140-S20-S05 14.0 31 101 20 50 SPMT050204E-DP
HP-2D145-S20-S05 14.5 32 102 20 50
HP-2D150-S20-S05 15.0 33 103 20 50
HP-2D155-S25-S06 15.5 34 115 25 56
HP-2D160-S25-S06 16.0 35 116 25 56
HP-2D165-S25-S06 16.5 36 117 25 56
HP-2D170-S25-S06 17.0 37 118 25 56
HP-2D175-S25-S06 17.5 38 119 25 56
HP-2D180-S25-S06 18.0 39 120 25 56
HP-2D185-S25-S06 18.5 40 121 25 56 SPMT060204E-DP
HP-2D190-S25-S06 19.0 41 122 25 56
HP-2D195-S25-S06 19.5 42 123 25 56
HP-2D200-S25-S06 20.0 43 124 25 56
HP-2D205-S25-S06 20.5 44 125 25 56
HP-2D210-S25-S06 21.0 45 126 25 56
HP-2D215-S25-S06 21.5 46 127 25 56
HP-2D220-S32-S07 22.0 47 137 32 60
HP-2D225-S32-S07 22.5 48 138 32 60
HP-2D230-S32-S07 23.0 49 139 32 60
HP-2D235-S32-S07 23.5 50 140 32 60
HP-2D240-S32-S07 24.0 51 141 32 60
HP-2D245-S32-S07 24.5 52 142 32 60
SPMT07T308E-DP
HP-2D250-S32-S07 25.0 53 143 32 60
HP-2D255-S32-S07 25.5 54 144 32 60
HP-2D260-S32-S07 26.0 55 145 32 60
HP-2D265-S32-S07 26.5 56 146 32 60
HP-2D270-S32-S07 27.0 57 147 32 60
HP-2D275-S32-S07 27.5 58 148 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

13-15 AST2043-60 AWF-T06

15.5-21.5 AST2255-60 AWF-T06

22-27.5 AST25065-60S AWF-T08

P273 P276
254
Drilling

DP Series Drilling Holder Length-diameter ratio：2D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-2D280-S32-S09 28.0 59 149 32 60

HP-2D285-S32-S09 28.5 60 150 32 60
HP-2D290-S32-S09 29.0 61 151 32 60
HP-2D295-S32-S09 29.5 63 153 32 60
SPMT090408E-DP
HP-2D300-S32-S09 30.0 65 155 32 60
HP-2D310-S32-S09 31.0 67 157 32 60
HP-2D320-S32-S09 32.0 69 159 32 60
HP-2D330-S32-S09 33.0 71 161 32 60
HP-2D340-S40-S11 34.0 73 178 40 70
HP-2D350-S40-S11 35.0 75 180 40 70

Drilling holders
HP-2D360-S40-S11 36.0 77 182 40 70
HP-2D370-S40-S11 37.0 79 184 40 70
SPMT110408E-DP
HP-2D380-S40-S11 38.0 81 186 40 70
HP-2D390-S40-S11 39.0 83 188 40 70
HP-2D400-S40-S11 40.0 85 190 40 70
HP-2D410-S40-S11 41.0 87 192 40 70
HP-2D420-S40-S14 42.0 89 194 40 70
HP-2D430-S40-S14 43.0 91 196 40 70
HP-2D440-S40-S14 44.0 93 198 40 70
HP-2D450-S40-S14 45.0 95 200 40 70
HP-2D460-S40-S14 46.0 97 202 40 70 SPMT140512E-DP
HP-2D470-S40-S14 47.0 99 204 40 70
HP-2D480-S40-S14 48.0 101 206 40 70
HP-2D490-S40-S14 49.0 103 208 40 70
HP-2D500-S40-S14 50.0 105 210 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

28-33 AST35084-60H AWF-T15

34-41 AST410-60H AWF-T15

42-50 AST5126-60 AWF-T20

P273 P276

255
 Drilling

DP Series Drilling Holder Length-diameter ratio：3D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-3D130-S20-S05 13.0 42 112 20 50

HP-3D135-S20-S05 13.5 44 114 20 50
HP-3D140-S20-S05 14.0 45 115 20 50 SPMT050204E-DP
HP-3D145-S20-S05 14.5 47 117 20 50
HP-3D150-S20-S05 15.0 48 118 20 50
HP-3D155-S25-S06 15.5 50 131 25 56
HP-3D160-S25-S06 16.0 51 132 25 56
HP-3D165-S25-S06 16.5 53 134 25 56
HP-3D170-S25-S06 17.0 54 135 25 56
HP-3D175-S25-S06 17.5 56 137 25 56
HP-3D180-S25-S06 18.0 57 138 25 56
HP-3D185-S25-S06 18.5 59 140 25 56 SPMT060204E-DP
HP-3D190-S25-S06 19.0 60 141 25 56
HP-3D195-S25-S06 19.5 62 143 25 56
HP-3D200-S25-S06 20.0 63 144 25 56
HP-3D205-S25-S06 20.5 65 146 25 56
HP-3D210-S25-S06 21.0 66 147 25 56
HP-3D215-S25-S06 21.5 68 149 25 56
HP-3D220-S32-S07 22.0 69 159 32 60
HP-3D225-S32-S07 22.5 71 161 32 60
HP-3D230-S32-S07 23.0 72 162 32 60
HP-3D235-S32-S07 23.5 74 164 32 60
HP-3D240-S32-S07 24.0 75 165 32 60
HP-3D245-S32-S07 24.5 77 167 32 60
SPMT07T308E-DP
HP-3D250-S32-S07 25.0 78 168 32 60
HP-3D255-S32-S07 25.5 80 170 32 60
HP-3D260-S32-S07 26.0 81 171 32 60
HP-3D265-S32-S07 26.5 83 173 32 60
HP-3D270-S32-S07 27.0 84 174 32 60
HP-3D275-S32-S07 27.5 86 176 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

13-15 AST2043-60 AWF-T06

15.5-21.5 AST2255-60 AWF-T06

22-27.5 AST25065-60S AWF-T08

P273 P276
256
Drilling

DP Series Drilling Holder Length-diameter ratio：3D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-3D280-S32-S09 28.0 87 177 32 60

HP-3D285-S32-S09 28.5 89 179 32 60
HP-3D290-S32-S09 29.0 90 180 32 60
HP-3D295-S32-S09 29.5 93 183 32 60
SPMT090408E-DP
HP-3D300-S32-S09 30.0 95 185 32 60
HP-3D310-S32-S09 31.0 98 188 32 60
HP-3D320-S32-S09 32.0 101 191 32 60
HP-3D330-S32-S09 33.0 104 194 32 60
HP-3D340-S40-S11 34.0 107 212 40 70
HP-3D350-S40-S11 35.0 110 215 40 70

Drilling holders
HP-3D360-S40-S11 36.0 113 218 40 70
HP-3D370-S40-S11 37.0 116 221 40 70
SPMT110408E-DP
HP-3D380-S40-S11 38.0 119 224 40 70
HP-3D390-S40-S11 39.0 122 227 40 70
HP-3D400-S40-S11 40.0 125 230 40 70
HP-3D410-S40-S11 41.0 128 233 40 70
HP-3D420-S40-S14 42.0 131 236 40 70
HP-3D430-S40-S14 43.0 134 239 40 70
HP-3D440-S40-S14 44.0 137 242 40 70
HP-3D450-S40-S14 45.0 140 245 40 70
HP-3D460-S40-S14 46.0 143 248 40 70 SPMT140512E-DP
HP-3D470-S40-S14 47.0 146 251 40 70
HP-3D480-S40-S14 48.0 149 254 40 70
HP-3D490-S40-S14 49.0 152 257 40 70
HP-3D500-S40-S14 50.0 155 260 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

28-33 AST35084-60H AWF-T15

34-41 AST410-60H AWF-T15

42-50 AST5126-60 AWF-T20

P273 P276

257
 Drilling

DP Series Drilling holder Length-diameter ratio：4D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-4D130-S20-S05 13.0 55 125 20 50

HP-4D135-S20-S05 13.5 57 127 20 50
HP-4D140-S20-S05 14.0 59 129 20 50 SPMT050204E-DP
HP-4D145-S20-S05 14.5 61 131 20 50
HP-4D150-S20-S05 15.0 63 133 20 50
HP-4D155-S25-S06 15.5 65 146 25 56
HP-4D160-S25-S06 16.0 67 148 25 56
HP-4D165-S25-S06 16.5 69 150 25 56
HP-4D170-S25-S06 17.0 71 152 25 56
HP-4D175-S25-S06 17.5 73 154 25 56
HP-4D180-S25-S06 18.0 75 156 25 56
HP-4D185-S25-S06 18.5 77 158 25 56 SPMT060204E-DP
HP-4D190-S25-S06 19.0 79 160 25 56
HP-4D195-S25-S06 19.5 81 162 25 56
HP-4D200-S25-S06 20.0 83 164 25 56
HP-4D205-S25-S06 20.5 85 166 25 56
HP-4D210-S25-S06 21.0 87 168 25 56
HP-4D215-S25-S06 21.5 89 170 25 56
HP-4D220-S32-S07 22.0 91 181 32 60
HP-4D225-S32-S07 22.5 93 183 32 60
HP-4D230-S32-S07 23.0 95 185 32 60
HP-4D235-S32-S07 23.5 97 187 32 60
HP-4D240-S32-S07 24.0 99 189 32 60
HP-4D245-S32-S07 24.5 101 191 32 60
SPMT07T308E-DP
HP-4D250-S32-S07 25.0 103 193 32 60
HP-4D255-S32-S07 25.5 105 195 32 60
HP-4D260-S32-S07 26.0 107 197 32 60
HP-4D265-S32-S07 26.5 109 199 32 60
HP-4D270-S32-S07 27.0 111 201 32 60
HP-4D275-S32-S07 27.5 113 203 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

13-15 AST2043-60 AWF-T06

15.5-21.5 AST2255-60 AWF-T06

22-27.5 AST25065-60S AWF-T08

P273 P276
258
Drilling

DP Series Drilling holder Length-diameter ratio：4D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-4D280-S32-S09 28.0 115 205 32 60

HP-4D285-S32-S09 28.5 117 207 32 60
HP-4D290-S32-S09 29.0 120 210 32 60
HP-4D295-S32-S09 29.5 123 213 32 60
SPMT090408E-DP
HP-4D300-S32-S09 30.0 125 215 32 60
HP-4D310-S32-S09 31.0 129 219 32 60
HP-4D320-S32-S09 32.0 133 223 32 60
HP-4D330-S32-S09 33.0 137 227 32 60
HP-4D340-S40-S11 34.0 141 246 40 70
HP-4D350-S40-S11 35.0 145 250 40 70

Drilling holders
HP-4D360-S40-S11 36.0 149 254 40 70
HP-4D370-S40-S11 37.0 153 258 40 70
SPMT110408E-DP
HP-4D380-S40-S11 38.0 157 262 40 70
HP-4D390-S40-S11 39.0 161 266 40 70
HP-4D400-S40-S11 40.0 165 270 40 70
HP-4D410-S40-S11 41.0 169 274 40 70
HP-4D420-S40-S14 42.0 173 278 40 70
HP-4D430-S40-S14 43.0 177 282 40 70
HP-4D440-S40-S14 44.0 181 286 40 70
HP-4D450-S40-S14 45.0 185 290 40 70
HP-4D460-S40-S14 46.0 189 294 40 70 SPMT140512E-DP
HP-4D470-S40-S14 47.0 193 298 40 70
HP-4D480-S40-S14 48.0 197 302 40 70
HP-4D490-S40-S14 49.0 201 306 40 70
HP-4D500-S40-S14 50.0 205 310 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

28-33 AST35084-60H AWF-T15

34-41 AST410-60H AWF-T15

42-50 AST5126-60 AWF-T20

P273 P276

259
 Drilling

DG Series Drilling holder Length-diameter ratio：2D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-2D160-S25-W03 16.0 35 116 25 56

HP-2D165-S25-W03 16.5 36 117 25 56
HP-2D170-S25-W03 17.0 37 118 25 56
HP-2D175-S25-W03 17.5 38 119 25 56
HP-2D180-S25-W03 18.0 39 120 25 56 WCMT 030204E-DG
HP-2D185-S25-W03 18.5 40 121 25 56
HP-2D190-S25-W03 19.0 41 122 25 56
HP-2D195-S25-W03 19.5 42 123 25 56
HP-2D200-S25-W03 20.0 43 124 25 56
HP-2D205-S25-W04 20.5 44 125 25 56
HP-2D210-S25-W04 21.0 45 126 25 56
HP-2D215-S25-W04 21.5 46 127 25 56
HP-2D220-S25-W04 22.0 47 128 25 56
HP-2D225-S25-W04 22.5 48 129 25 56
WCMT 040204E-DG
HP-2D230-S25-W04 23.0 49 130 25 56
HP-2D235-S25-W04 23.5 50 131 25 56
HP-2D240-S25-W04 24.0 51 132 25 56
HP-2D245-S25-W04 24.5 52 133 25 56
HP-2D250-S25-W04 25.0 53 134 25 56
HP-2D255-S32-W05 25.5 54 144 32 60
HP-2D260-S32-W05 26.0 55 145 32 60
HP-2D265-S32-W05 26.5 56 146 32 60
HP-2D270-S32-W05 27.0 57 147 32 60
HP-2D275-S32-W05 27.5 58 148 32 60
WCMT 050308E-DG
HP-2D280-S32-W05 28.0 59 149 32 60
HP-2D285-S32-W05 28.5 60 150 32 60
HP-2D290-S32-W05 29.0 61 151 32 60
HP-2D295-S32-W05 29.5 62 152 32 60
HP-2D300-S32-W05 30.0 63 153 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

16-20 AST22045-55 AWF-T06

20.5-25 AST25055-50 AWF-T08

25.5-30 AST307-55 AWF-T08

P273 P277

260
Drilling

DG Series Drilling holder Length-diameter ratio：2D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-2D310-S32-W06 31.0 65 155 32 60

HP-2D320-S32-W06 32.0 67 157 32 60
HP-2D330-S32-W06 33.0 69 159 32 60
HP-2D340-S32-W06 34.0 71 161 32 60
HP-2D350-S32-W06 35.0 73 163 32 60
HP-2D360-S32-W06 36.0 75 165 32 60 WCMT 06T308E-DG
HP-2D370-S32-W06 37.0 77 167 32 60
HP-2D380-S32-W06 38.0 79 169 32 60
HP-2D390-S32-W06 39.0 81 171 32 60
HP-2D400-S32-W06 40.0 83 173 32 60

Drilling holders
HP-2D410-S32-W06 41.0 85 175 32 60
HP-2D420-S40-W08 42.0 87 192 40 70
HP-2D430-S40-W08 43.0 89 194 40 70
HP-2D440-S40-W08 44.0 91 196 40 70
HP-2D450-S40-W08 45.0 93 198 40 70
HP-2D460-S40-W08 46.0 95 200 40 70
HP-2D470-S40-W08 47.0 97 202 40 70
HP-2D480-S40-W08 48.0 99 204 40 70
HP-2D490-S40-W08 49.0 101 206 40 70
HP-2D500-S40-W08 50.0 103 208 40 70 WCMT 080408E-DG
HP-2D510-S40-W08 51.0 105 210 40 70
HP-2D520-S40-W08 52.0 107 212 40 70
HP-2D530-S40-W08 53.0 109 214 40 70
HP-2D540-S40-W08 54.0 111 216 40 70
HP-2D550-S40-W08 55.0 113 218 40 70
HP-2D560-S40-W08 56.0 115 220 40 70
HP-2D570-S40-W08 57.0 117 222 40 70
HP-2D580-S40-W08 58.0 119 224 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

31-41 AST3509-55 AWF-T15

42-58 AST411-60W-M AWF-T15

P273 P277

261
 Drilling

DG Series Drilling holder Length-diameter ratio：3D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-3D160-S25-W03 16.0 51 132 25 56

HP-3D165-S25-W03 16.5 53 134 25 56
HP-3D170-S25-W03 17.0 54 135 25 56
HP-3D175-S25-W03 17.5 56 137 25 56
HP-3D180-S25-W03 18.0 57 138 25 56 WCMT 030204E-DG
HP-3D185-S25-W03 18.5 59 140 25 56
HP-3D190-S25-W03 19.0 60 141 25 56
HP-3D195-S25-W03 19.5 62 143 25 56
HP-3D200-S25-W03 20.0 63 144 25 56
HP-3D205-S25-W04 20.5 65 146 25 56
HP-3D210-S25-W04 21.0 66 147 25 56
HP-3D215-S25-W04 21.5 68 149 25 56
HP-3D220-S25-W04 22.0 69 150 25 56
HP-3D225-S25-W04 22.5 71 152 25 56
WCMT 040204E-DG
HP-3D230-S25-W04 23.0 72 153 25 56
HP-3D235-S25-W04 23.5 74 155 25 56
HP-3D240-S25-W04 24.0 75 156 25 56
HP-3D245-S25-W04 24.5 77 158 25 56
HP-3D250-S25-W04 25.0 78 159 25 56
HP-3D255-S32-W05 25.5 80 170 32 60
HP-3D260-S32-W05 26.0 81 171 32 60
HP-3D265-S32-W05 26.5 83 173 32 60
HP-3D270-S32-W05 27.0 84 174 32 60
HP-3D275-S32-W05 27.5 86 176 32 60
WCMT 050308E-DG
HP-3D280-S32-W05 28.0 87 177 32 60
HP-3D285-S32-W05 28.5 89 179 32 60
HP-3D290-S32-W05 29.0 90 180 32 60
HP-3D295-S32-W05 29.5 92 182 32 60
HP-3D300-S32-W05 30.0 93 183 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

16-20 AST22045-55 AWF-T06

20.5-25 AST25055-50 AWF-T08

25.5-30 AST307-55 AWF-T08

P273 P277

262
Drilling

DG Series Drilling holder Length-diameter ratio：3D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-3D310-S32-W06 31.0 96 186 32 60

HP-3D320-S32-W06 32.0 99 189 32 60
HP-3D330-S32-W06 33.0 102 192 32 60
HP-3D340-S32-W06 34.0 105 195 32 60
HP-3D350-S32-W06 35.0 108 198 32 60
HP-3D360-S32-W06 36.0 111 201 32 60 WCMT 06T308E-DG
HP-3D370-S32-W06 37.0 114 204 32 60
HP-3D380-S32-W06 38.0 117 207 32 60
HP-3D390-S32-W06 39.0 120 210 32 60
HP-3D400-S32-W06 40.0 123 213 32 60

Drilling holders
HP-3D410-S32-W06 41.0 126 216 32 60
HP-3D420-S40-W08 42.0 129 234 40 70
HP-3D430-S40-W08 43.0 132 237 40 70
HP-3D440-S40-W08 44.0 135 240 40 70
HP-3D450-S40-W08 45.0 138 243 40 70
HP-3D460-S40-W08 46.0 141 246 40 70
HP-3D470-S40-W08 47.0 144 249 40 70
HP-3D480-S40-W08 48.0 147 252 40 70
HP-3D490-S40-W08 49.0 150 255 40 70
HP-3D500-S40-W08 50.0 153 258 40 70 WCMT 080408E-DG
HP-3D510-S40-W08 51.0 156 261 40 70
HP-3D520-S40-W08 52.0 159 264 40 70
HP-3D530-S40-W08 53.0 162 267 40 70
HP-3D540-S40-W08 54.0 165 270 40 70
HP-3D550-S40-W08 55.0 168 273 40 70
HP-3D560-S40-W08 56.0 171 276 40 70
HP-3D570-S40-W08 57.0 174 279 40 70
HP-3D580-S40-W08 58.0 177 282 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

31-41 AST3509-55 AWF-T15

42-58 AST411-60W-M AWF-T15

P273 P277

263
 Drilling

DG Series Drilling holder Length-diameter ratio：4D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-4D160-S25-W03 16.0 67 148 25 56

HP-4D165-S25-W03 16.5 69 150 25 56
HP-4D170-S25-W03 17.0 71 152 25 56
HP-4D175-S25-W03 17.5 73 154 25 56
HP-4D180-S25-W03 18.0 75 156 25 56 WCMT 030204E-DG
HP-4D185-S25-W03 18.5 77 158 25 56
HP-4D190-S25-W03 19.0 79 160 25 56
HP-4D195-S25-W03 19.5 81 162 25 56
HP-4D200-S25-W03 20.0 83 164 25 56
HP-4D205-S25-W04 20.5 85 166 25 56
HP-4D210-S25-W04 21.0 87 168 25 56
HP-4D215-S25-W04 21.5 89 170 25 56
HP-4D220-S25-W04 22.0 91 172 25 56
HP-4D225-S25-W04 22.5 93 174 25 56
WCMT 040204E-DG
HP-4D230-S25-W04 23.0 95 176 25 56
HP-4D235-S25-W04 23.5 97 178 25 56
HP-4D240-S25-W04 24.0 99 180 25 56
HP-4D245-S25-W04 24.5 101 182 25 56
HP-4D250-S25-W04 25.0 103 184 25 56
HP-4D255-S32-W05 25.5 105 195 32 60
HP-4D260-S32-W05 26.0 107 197 32 60
HP-4D265-S32-W05 26.5 109 199 32 60
HP-4D270-S32-W05 27.0 111 201 32 60
HP-4D275-S32-W05 27.5 113 203 32 60
WCMT 050308E-DG
HP-4D280-S32-W05 28.0 115 205 32 60
HP-4D285-S32-W05 28.5 117 207 32 60
HP-4D290-S32-W05 29.0 119 209 32 60
HP-4D295-S32-W05 29.5 121 211 32 60
HP-4D300-S32-W05 30.0 123 213 32 60

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

16-20 AST22045-55 AWF-T06

20.5-25 AST25055-50 AWF-T08

25.5-30 AST307-55 AWF-T08

P273 P277

264
Drilling

DG Series Drilling holder Length-diameter ratio：4D

Dimension(mm)
Product code Inserts
D L1 L DS LS

HP-4D310-S32-W06 31.0 127 217 32 60

HP-4D320-S32-W06 32.0 131 221 32 60
HP-4D330-S32-W06 33.0 135 225 32 60
HP-4D340-S32-W06 34.0 139 229 32 60
HP-4D350-S32-W06 35.0 143 233 32 60
HP-4D360-S32-W06 36.0 147 237 32 60 WCMT 06T308E-DG
HP-4D370-S32-W06 37.0 151 241 32 60
HP-4D380-S32-W06 38.0 155 245 32 60
HP-4D390-S32-W06 39.0 159 249 32 60
HP-4D400-S32-W06 40.0 163 253 32 60

Drilling holders
HP-4D410-S32-W06 41.0 167 257 32 60
HP-4D420-S40-W08 42.0 171 276 40 70
HP-4D430-S40-W08 43.0 175 280 40 70
HP-4D440-S40-W08 44.0 179 284 40 70
HP-4D450-S40-W08 45.0 183 288 40 70
HP-4D460-S40-W08 46.0 187 292 40 70
HP-4D470-S40-W08 47.0 191 296 40 70
HP-4D480-S40-W08 48.0 195 300 40 70
HP-4D490-S40-W08 49.0 199 304 40 70
HP-4D500-S40-W08 50.0 203 308 40 70 WCMT 080408E-DG
HP-4D510-S40-W08 51.0 207 312 40 70
HP-4D520-S40-W08 52.0 211 316 40 70
HP-4D530-S40-W08 53.0 215 320 40 70
HP-4D540-S40-W08 54.0 219 324 40 70
HP-4D550-S40-W08 55.0 223 328 40 70
HP-4D560-S40-W08 56.0 227 332 40 70
HP-4D570-S40-W08 57.0 231 336 40 70
HP-4D580-S40-W08 58.0 235 340 40 70

Dimensions (mm) Spare parts

Holder diameter Screw Wrench

31-41 AST3509-55 AWF-T15

42-58 AST411-60W-M AWF-T15

P273 P277

265
 Drilling

Drilling Insert Denomination System

S P M T
1 2 3 4

1- Shape/Code 2- Clearance angle

S A B C D E

90°

W F G N P O

80° Other clearance

angle

3- Tolerance

Shape: C, E, H, M, O, P, S, T, R, W
d m
IC
J,K,L,M,N U M, N U

4.76 ± 0,05 ± 0,08 ± 0,08 ± 0,13

In.Circle dimension Nose height 5.56 ± 0,05 ± 0,08 ± 0,08 ± 0,13
Class Unit Thicknesss
d m
6 ± 0,05 ± 0,08 ± 0,08 ± 0,13
A mm ± 0,025 ± 0,005 ± 0,025
6.35 ± 0,05 ± 0,08 ± 0,08 ± 0,13
C mm ± 0,025 ± 0,013 ± 0,025
7.94 ± 0,05 ± 0,08 ± 0,08 ± 0,13
E mm ± 0,025 ± 0,025 ± 0,025
8 ± 0,05 ± 0,08 ± 0,08 ± 0,13
F mm ± 0,013 ± 0,005 ± 0,025
9.525 ± 0,05 ± 0,08 ± 0,08 ± 0,13
G mm ± 0,025 ± 0,025 ± 0,13
10 ± 0,05 ± 0,08 ± 0,08 ± 0,13
H mm ± 0,013 ± 0,013 ± 0,025
12 ± 0,08 ± 0,13 ± 0,13 ± 0,2
J mm * ± 0,005 ± 0,025
12.7 ± 0,08 ± 0,13 ± 0,13 ± 0,2
K mm * ± 0,013 ± 0,025
15.875 ± 0,1 ± 0,18 ± 0,15 ± 0,27
L mm * ± 0,025 ± 0,025
16 ± 0,1 ± 0,18 ± 0,15 ± 0,27
M mm * * ± 0,127
19.05 ± 0,1 ± 0,18 ± 0,15 ± 0,27
U mm * * ± 0,127
20 ± 0,1 ± 0,18 ± 0,15 ± 0,27
N mm * * ± 0,025
25 ± 0,13 ± 0,25 ± 0,18 ± 0,38
* For details refer to right and below tables
25.4 ± 0,13 ± 0,25 ± 0,18 ± 0,38

31.75 ± 0,15 ± 0,25 ± 0,2 ± 0,38

32 ± 0,15 ± 0,25 ± 0,2 ± 0,38

M&N shape D shape V shape 4- Clamping type

IC d m d m
A B C F G
5.56 ± 0,05 ± 0,11

6.35 ± 0,05 ± 0,11 ± 0,05 ± 0,16

7.94 ± 0,05 ± 0,11 ± 0,05 ± 0,16 H J M N Q

9.525 ± 0,05 ± 0,11 ± 0,05 ± 0,16

70°-90°
12.7 ± 0,08 ± 0,15 ± 0,08 ± 0,2 R T U W X
15.875 ± 0,10 ± 0,18 ± 0,10 ± 0,27
Special
19.05 ± 0,10 ± 0,18 ± 0,10 ± 0,27

266
Drilling

06 02 04 E - DP
5 6 7 8 - 9

5- Cutting edge length 6- Insert thickness

S W
In.Circle S W
I I Thickness Thickness mark Example
Dimension
(mm) illustration
Code Length Code Length

5.56 03 3.8
00 = 0.79
6.35 06 6.35 04 4.3 T0 = 0.99
7.94 05 5.4 01 = 1.59
8.0 08 8.0 T1 = 1.98
02 = 2.38
9.525 09 9.525 06 6.5
T2 = 2.58
12.7 12 12.7 08 8.7
Insert thickness "S" 03 = 3.18
refers to the distance T3 = 3.97
between cutting edge 04 = 4.76
nose and bottom
7- Corner radius T4 = 4.96
05 = 5.56
Example T5 = 5.95
04 = 0.4 06 = 6.35
08 = 0.8 07 = 7.94
12 = 1.2 09 = 9.53
11 = 11.11
12 = 12.70
14 = 14.29
15 = 15.88

Drilling inserts
8- Cutting edge shape
9- Chip breaker code

Example Illustration DP DU/DG

E Honed cutting edge
F Sharp cutting edge
T Negative land

10. Chip breakers' information refer to page 298

267
 Drilling

Geometry Application Guide

DP

1. DP geometry has high efficiency. Suitable for short hole high speed drilling.
2. Strong square insert with reinforced geometry offers excellent hole straightness.
3. Drilling holder with helical flute provides excellent chip evacuation and high hole precision.

DU/DG

1. Suitable cutting angle makes perfect balance for the cutting force.
2. General purpose geometry combined with two grades are suitable for P,M,K,S materials,
especially good for the chip control in soft materials.
3. Obtains good surface finish.
4. Good versatility. It's suitable for rotating and non-rotating machining.

268
Drilling

Grade Application Guide

Drilling insert grade ISO group

Material
Materials ISO AP301U AP351U AP351M AC301P ISO
Group
P01 P01
P05 P05
P10 P10
P15 P15
P20 P20
Unalloy steels /
P25 AP301U P25
P Alloyed steels
P30 P30
AC301P
P35 AP351M P35
AP351U
P40 P40
P45 P45
P50 P50
M01 M01
M05 M05
M10 M10
M15 M15
M20 M20
Stainless steels
M M25 AP301U M25
M30 M30
M35 AP351M M35
AP351U
M40 M40
M45 M45
K01 K01
K05 K05
K10 K10

Drilling inserts
K15 K15
K20 K20
Cast iron
K K25 K25
K30 K30
K35 K35
K40 K40
K45 K45
S01 S01
S05 S05
S10 S10
S15 S15
Heat resistant S20 S20
S alloys S25 S25
S30 S30
S35 AP351M S35
AP351U
S40 S40
S45 S45
N01 N01
N05 N05
N10 N10
N Aluminum/
Aluminum alloys
N15 N15
N20 N20
N25 N25
N30 N30
H01 H01
H05 H05
H10 H10
H Hardened steels/
Chilled cast iron
H15 H15
H20 H20
H25 H25
H30 H30

269
 Drilling

Grade Application Guide

PVD coated CVD coated

Materials
AP301U AP351U AP351M AC301P

Material Tensile strength Hardness

ISO Priority
classification (N/mm2) (HB)

<600 <180 ● ● ● ●

Unalloyed steel
<950 <280 ● ● ● ●

P 700-950 200-280 ● ● ● ●

Alloyed steel 950-1200 280-355 ● ● ● ●

1200-1400 355-415 ● ● ● ●

Duplex stainless steel 778 230 ◐ ● ● -

M Austenitic stainless steel 675 200 ◐ ● ● -

Precipitation-hardening
1013 300 ◐ ● ● -
stainless steel

Grey cast iron 700 220 - - - -

K Nodular cast iron 880 260 - - - -

Malleable cast iron 800 250 - - - -

Fe-based alloy 943 280 - ◐ ● -

Co-based alloy 1076 320 - ◐ ● -

S
Ni-based alloy 1177 350 - ◐ ● -

Ti-alloy 1262 370 - ◐ ● -

Aluminum 260 75 - - - -

N
Aluminum alloy 447 130 - - - -

-
-
Hardened steel 50-60HRC - - -

H
- -
-
Chilled cast iron 55HRC - -

● Best choice
◐ 2nd choice
- Inapplicable

270
Drilling

Drilling Grade Description

AP301U

Coating: PVD coating

Suitable for steel, stainless steel drilling. High strength and wear resistance ultra fine
carbide substrate with nanostructured PVD coating in controllable layer, high coating
adhesion, wear-resistance and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP301U
M AP301U
K

Remark: Best choice

2nd choice

Drilling inserts
AP351U

Coating: PVD coating

Suitable for steel, stainless steel and heat resistant alloy drilling. High strength carbide
substrate with nanostructured PVD coating in controllable layer, high coating adhesion,
wear-resistance and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP351U
M AP351U
K

S AP351U
N

Remark: Best choice

2nd choice

271
 Drilling

AC301P

Coating: CVD coating

For steel and cast iron drilling. High strength substrate combined with multi-layer CVD,
good coating adhesion and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AC301P
M

Remark: Best choice

2nd choice

AP351M

Coating: PVD coating

Suitable for steel, stainless steel and heat resistant alloy drilling. Good stability and wear
resistance. Good thermal crack resistance and high coating adhesion and strength.

Application range
ISO
01 05 10 15 20 25 30 35 40 45 50
Classification
P AP351M
M AP351M
K

S AP351M
N

Remark: Best choice

2nd choice

272
Drilling

SPMT-DP Drilling Insert

Dimension(mm) Grades

Inserts Product code

AP351M

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K
AP351K

AP403S
l d s r h

SPMT 050204E-DP 5 5 2.38 0.4 2.25 ● ● ● ●

SPMT 060204E-DP 6 6 2.38 0.4 2.61 ● ● ● ●

SPMT 07T308E-DP 7.94 7.94 3.97 0.8 2.85 ● ● ● ●

SPMT 090408E-DP 9.8 9.8 4.3 0.8 4.05 ● ● ● ●

SPMT 110408E-DP 11.5 11.5 4.8 0.8 4.45 ● ● ● ●

SPMT 140512E-DP 14.3 14.3 5.2 1.2 5.75 ● ● ● ●

Drilling inserts
Marked：● Stock available

P254 P276

273
 Drilling

WCMT-DU Drilling Insert

Dimension(mm) Grades

Inserts Product code

AP351M

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K
AP351K

AP403S
l d s r h

WCMT 030208E-DU 3.8 5.56 2.38 0.8 2.8 ● ●

WCMT 040208E-DU 4.3 6.35 2.38 0.8 3.0 ● ●

WCMT 050308E-DU 5.4 7.94 3.18 0.8 3.4 ● ●

WCMT 06T308E-DU 6.5 9.525 3.97 0.8 3.9 ● ●

WCMT 080412E-DU 8.7 12.7 4.76 1.2 4.4 ● ●

Note: The DU insert is a universal insert and Achteck does not provide a tool holder. Marked：● Stock available

P254 P276

274
Drilling

WCMT-DG Drilling Insert

Dimension(mm) Grades

Inserts Product code

AP351M

AW100K
AP301U

AP351U

AC301P

AP401U

AC301K
AP351K

AP403S
l d s r h

WCMT 030204E-DG 3.8 5.56 2.38 0.4 2.5 ● ●

WCMT 040204E-DG 4.3 6.35 2.38 0.4 2.8 ● ●

WCMT 050308E-DG 5.4 7.94 3.18 0.8 3.4 ● ●

WCMT 06T308E-DG 6.5 9.525 3.97 0.8 4.45 ● ●

WCMT 080408E-DG 8.7 12.7 4.76 0.8 5.5 ● ●

Drilling inserts
Marked：● Stock available

P254 P276

275
276
Cutting Parameter Recommendation

Materials SP drilling insert series grade apllication range & cutting parameter recommendation
Grade

AP301U AP351U AP351M AC301P

P15-35 P30-45 P20-35 P25-40

M15-35 M30-45 M20-35 -

Feed
- - - -
Tensile (mm/rev)
Material Hardness
ISO strength - S 30-45 S20-35 -
classification (HB)
(N/mm2)
- - - -

- - -

Feed (mm/rev)

Min Med Max Min Med Max Min Med Max Min Med Max φ13mm～φ15 mm φ15.5mm～φ21.5mm φ22mm ～ φ27.5mm φ28mm～φ33 mm φ34mm～φ41mm φ42mm～φ50 mm

Cutting speed (m/min) SPMT 050204E-DP SPMT 060204E-DP SPMT 07T308E-DP SPMT 090408E-DP SPMT 110408E-DP SPMT 140512E-DP

<600 <180 260 240 224 220 185 150 240 220 200 200 175 150 0.05-0.08 0.06-0.10 0.06-0.12 0.07-0.13 0.08-0.15 0.08-0.16
Unalloyed steel
<950 <280 250 210 170 200 170 140 230 190 160 190 162.5 135 0.06-0.12 0.08-0.15 0.10-0.18 0.12-0.22 0.12-0.24 0.13-0.25

P 700-950 200-280 240 200 160 190 160 130 220 180 150 180 150 120 0.06-0.10 0.08-0.14 0.10-0.18 0.12-0.22 0.12-0.23 0.13-0.24

Alloyed steel 950-1200 280-355 210 170 130 170 130 90 190 150 110 160 130 100 0.06-0.12 0.08-0.15 0.10-0.18 0.12-0.22 0.12-0.24 0.13-0.25

1200-1400 355-415 170 140 110 160 120 80 150 120 90 140 110 80 0.06-0.10 0.08-0.14 0.10-0.18 0.12-0.22 0.12-0.23 0.13-0.24

Duplex stainless
778 230 260 200 140 180 135 90 240 180 120 - - - 0.05-0.10 0.06-0.12 0.08-0.15 0.09-0.16 0.10-0.17 0.11-0.18
steel
Austenitic stainless
675 200 220 170 120 120 65 60 200 150 100 - - - 0.05-0.10 0.06-0.12 0.08-0.15 0.09-0.16 0.10-0.17 0.11-0.18
M steel
Precipitation-
hardening stainless 1013 300 180 140 100 90 65 40 160 120 80 - - - - - - - - -
steel
Grey cast iron 700 220 - - - - - - - - - - - - - - - - - -

K Nodular cast iron 880 260 - - - - - - - - - - - - - - - - - -

Malleable cast iron 800 250 - - - - - - - - - - - - - - - - - -

Fe-based alloy 943 280 - - - 40 30 20 45 35 25 - - - - - - - - -

Co-based alloy 1076 320 - - - 35 25 15 40 30 20 - - - - - - - - -

S
Ni-based alloy 1177 350 - - - 35 25 15 40 30 20 - - - - - - - - -

Ti-alloy 1262 370 - - - 40 30 20 45 35 25 - - - 0.05-0.10 0.06-0.14 0.08-0.18 0.10-0.22 0.14-0.23 0.15-0.24

Aluminum 260 75 - - - - - - - - - - - - - - - - - -
N
Aluminum alloy 447 130 - - - - - - - - - - - - - - - - - -
-
Hardened steel 50-60HRC - - - - - - - - - - - - - - - - - -
H -
Chilled cast iron 55HRC - - - - - - - - - - - - - - - - - -
Drilling

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece clamping and coolants.
 Cutting Parameter Recommendation
Drilling

Materials WC drilling insert series grade apllication range & cutting parameter recommendation
AP301U AP351U AC301P

PVD coated PVD coated CVD coated

P15-35 P30-45 P25-40

M15-35 M30-45 -
Feed
- - -
Tensile (mm/rev)
Material Hardness
ISO strength - S 30-45 -
classification (HB)
(N/mm2)
- - -

- - -

Feed (mm/rev)

Min Med Max Min Med Max Min Med Max φ16mm～φ20 mm φ20.5mm～φ25mm φ25.5mm ～ φ30 mm φ31mm～φ41 mm φ41mm～φ58 mm

Cutting speed (m/min) WCMT 030204E-DU/DG WCMT 040204E-DU/DG WCMT 050308E-DU/DG WCMT 06T308E-DU/DG WCMT 080408E-DU/DG

<600 <180 260 240 224 220 185 150 200 175 150 0.04-0.065 0.07-0.09 0.07-0.10 0.08-0.11 0.09-0.13
Unalloyed steel
<950 <280 250 210 170 200 170 140 190 162.5 135 0.05-0.07 0.09-0.09 0.07-0.10 0.08-0.11 0.09-0.13

P 700-950 200-280 240 200 160 190 160 130 180 150 120 0.05-0.09 0.065-0.14 0.08-0.16 0.10-0.18 0.10-0.20

Alloyed steel 950-1200 280-355 210 170 130 170 130 90 160 130 100 0.04-0.07 0.065-0.11 0.07-0.14 0.09-0.15 0.10-0.18

1200-1400 355-415 170 140 110 160 120 80 140 110 80 0.04-0.065 0.05-0.9 0.07-0.10 0.08-0.12 0.09-0.13

Duplex stainless
778 230 260 200 140 180 135 90 - - - 0.04-0.07 0.065-0.11 0.08-0.14 0.08-0.11 0.09-0.13
steel
Austenitic stainless
675 200 220 170 120 120 65 60 - - - 0.04-0.065 0.065-0.10 0.08-0.12 0.08-0.10 0.08-0.11
M steel
Precipitation-
hardening stainless 1013 300 180 140 100 90 65 40 - - - - - - - -
steel
Grey cast iron 700 220 - - - - - - - - - - - - - -

K Nodular cast iron 880 260 - - - - - - - - - - - - - -

Malleable cast iron 800 250 - - - - - - - - - - - - - -

Fe-based alloy 943 280 - - - 40 30 20 - - - - - - - -

Co-based alloy 1076 320 - - - 35 25 15 - - - - - - - -

S
Ni-based alloy 1177 350 - - - 35 25 15 - - - - - - - -

Ti-alloy 1262 370 - - - 40 30 20 - - - 0.05-0.10 0.06-0.11 0.07-0.12 0.08-0.13 0.08-0.14

Aluminum 260 75 - - - - - - - - - - - - - -
N
Aluminum alloy 447 130 - - - - - - - - - - - - - -
-
Hardened steel 50-60HRC - - - - - - - - - - - - - -
H -
Chilled cast iron 55HRC - - - - - - - - - - - - - -

*The recommended cutting conditions always refer to general conditions. These cutting conditions should be adjusted according to the practical machine rigidity, tools, workpiece clamping and coolants.

277
Drilling inserts
 Drilling

Deep-hole Drilling Product Introduction

Achteck has launched general-purpose deep-hole drilling inserts, which offer high productivity for many industries: energy, engineering
machinery, injection molding, aircraft, shipbuilding, military, etc. It can achieve good hole straightness in deep hole drilling and good
surface finish. Existing geometries and grades cover steel, stainless steel and heat resistant alloy drilling.

Product application and features

● The inserts can be mounted on the deep-hole drilling head.

● AP301U(N) is the first choice for drilling steel and stainless steel

● All geometries offer good chip-breaking result

● Increased efficiency due to high feed rate

● Reduces the cost per hole

Grade and Application

Workpiece material
Grade Coating
P M K S N H
AP301U(N) PVD ● ● ○

Marked：1st Choice Marked：2nd Choice Marked：Supplementary application

ISO P : (P15-P35) General-purpose PVD coating with excellent wear-resistance and toughness.
ISO M :(M15-M35) General-purpose grade for ISO-M applications, PVD coating with excellent toughness and
resistance to built-up edges.
ISO S :(S15-S35) PVD coating with excellent wear resistance and toughness, good resistance to built-up edges.

Geometry Types and Features

Geometry Edge shape Application

● For general purpose.

DH ● Suitable for high cutting speed and feed.
● Good chip control in most of materials.

● Suitable for long chip materials (such as low carbon alloy steel and duplex
stainless steel).
DL ● Obtain a reliable production process in drilling materials where chip jamming

can be a problem.

● With open geometry;

LH ● Suitable for high cutting speed and feed.

278
Drilling

DH Geometry

W
75° S

d1
l

r 11°

Center insert Product code l w s r d1 Competitor’s description Stock

EPMT 050308C-DH AP301U(N) 5.56 8 3.18 0.8 2.5 800-050308M-C-G 1025 ●

EPMT 06T308C-DH AP301U(N) 6.35 9.87 3.97 0.8 2.8 800-06T308M-C-G 1025 ●

EPMT 08T308C-DH AP301U(N) 7.94 9.87 3.97 0.8 2.8 800-08T308M-C-G 1025 ●

EPMT 10T308C-DH AP301U(N) 9.53 9.87 3.97 0.8 2.8 800-10T308M-C-G 1025 ●

EPMT 12T308C-DH AP301U(N) 12.7 9.87 3.97 0.8 2.8 800-12T308M-C-G 1025 ●

W
75° S

Drilling inserts
d1
l

r
11°

Intermediate insert Product code l w s r d1 Competitor’s description Stock

EPMT 050308I-DH AP301U(N) 5.56 8 3.18 0.8 2.5 800-050308M-I-G 1025 ●

EPMT 06T308I-DH AP301U(N) 6.35 9.87 3.97 0.8 2.8 800-06T308M-I-G 1025 ●

EPMT 08T308I-DH AP301U(N) 7.94 9.87 3.97 0.8 2.8 800-08T308M-I-G 1025 ●

EPMT 12T308I-DH AP301U(N) 12.7 9.87 3.97 0.8 2.8 800-12T308M-I-G 1025 ●

Marked：● Stock available

P284

279
 Drilling

DH Geometry
w
s

d1
l

r 85°
11°

Periphery insert Product code l w s r d1 Competitor’s description Stock

APHT 060308P-DH AP301U(N) 6.5 8 3.18 0.8 2.5 800-060308H-P-G 1025 ●

APHT 08T308P-DH AP301U(N) 8.5 9 3.97 0.8 2.8 800-08T308H-P-G 1025 ●

APHT 09T308P-DH AP301U(N) 9.66 9 3.97 0.8 2.8 800-09T308H-P-G 1025 ●

APHT 11T308P-DH AP301U(N) 12.75 9 3.97 0.8 2.8 800-11T308H-P-G 1025 ●

DL Geometry

w s
75°
d1
l

r
11°

Intermediate insert Product code l w s r d1 Competitor’s description Stock

EPMT 050308I-DL AP301U(N) 5.56 8 3.18 0.8 2.5 800-050308M-I-L 1025 ●

EPMT 06T308I-DL AP301U(N) 6.35 9.87 3.97 0.8 2.8 800-06T308M-I-L 1025 ●

EPMT 08T308I-DL AP301U(N) 7.94 9.87 3.97 0.8 2.8 800-08T308M-I-L 1025 ●

EPMT 12T308I-DL AP301U(N) 12.7 9.87 3.97 0.8 2.8 800-12T308M-I-L 1025 ●

w s
d1
l

r 85° 11°

Periphery insert Product code l w s r d1 Competitor’s description Stock

APHT 060308P-DL AP301U(N) 6.5 8 3.18 0.8 2.5 800-060308H-P-L 1025 ●

APHT 08T308P-DL AP301U(N) 8.5 9 3.97 0.8 2.8 800-08T308H-P-L 1025 ●

APHT 09T308P-DL AP301U(N) 9.66 9 3.97 0.8 2.8 800-09T308H-P-L 1025 ●

APHT 11T308P-DL AP301U(N) 12.75 9 3.97 0.8 2.8 800-11T308H-P-L 1025 ●

Marked：● Stock available

P284

280
Drilling

DH Geometry

60°

d1
l r 11°

Center/Intermediate
Product code l d s r d1 Competitor’s description Stock
insert

TPMT 16T312R-DH AP301U(N) 16.5 9.525 3.97 1.2 3.4 TPMT 16T312R-23 1025 ●

TPMT 220612R-DH AP301U(N) 22 12.7 6.35 1.2 4.4 TPMT 220612R-23 1025 ●

w
s
d1
l

r 11°

Drilling inserts
Periphery insert Product code l d s r d1 Competitor’s description Stock

APMT 13T308-DH AP301U(N) 14.6 10 3.97 0.8 3.4 R424.9-13T308-23 1025 ●

APMT 180608-DH AP301U(N) 20.6 11.5 6.35 0.8 4.4 R424.9-180608-23 1025 ●

Marked：● Stock available

P285

281
 Drilling

LH Geometry

60°

d1
r 11°
l

Center/Intermediate
Product code l d s r d1 Competitor’s description Stock
insert

TPMT 16T312R-LH AP301U(N) 16.5 9.525 3.97 1.2 3.4 TPMT 16T312R-22 1025 ●

TPMT 220612R-LH AP301U(N) 22 12.7 6.35 1.2 4.4 TPMT 220612R-22 1025 ●

w
s
d1
l

r 11°

Periphery insert Product code l d s r d1 Competitor’s description Stock

APMT 13T308-LH AP301U(N) 14.6 10 3.97 0.8 3.4 R424.9-13T308-22 1025 ●

APMT 180608-LH AP301U(N) 20.6 11.5 6.35 0.8 4.4 R424.9-180608-22 1025 ●

Marked：● Stock available

P285

282
Drilling

Guiding Pad

Guiding pad Product code b l s Competitor’s description Stock

GPAD-06A AC301K 6.00 18.00 3.00 800-06A PM1 ●

GPAD-07A AC301K 6.90 20.00 3.50 800-07A PM1 ●

GPAD-08A AC301K 8.00 25.00 4.50 800-08A PM1 ●

GPAD-10A AC301K 10.00 30.00 4.50 800-10A PM1 ●

GPAD-12A AC301K 12.00 35.00 5.50 800-12A PM1 ●

TPMX Series

r
11°
d

Drilling inserts
60°

d1

Sharp Product code s d r d1 Competitor’s description Stock

TPMX 1403R-DH AP301U(N) 3.50 8.45 0.80 2.87 TPMX 1403RG TT9030 ●

TPMX 1704R-DH AP301U(N) 4.00 10.30 0.80 3.90 TPMX 1704RG TT9030 ●

TPMX 2405R-DH AP301U(N) 5.50 14.20 1.20 4.40 TPMX 2405RG TT9030 ●

TPMX 2405L-DH AP301U(N) 5.50 14.20 1.20 4.40 TPMX 2405LG TT9030 ●

TPMX 2807R-DH AP301U(N) 7.50 17.00 1.60 5.50 TPMX 2807RG TT9030 ●

Marked：● Stock available

P285

283
 Drilling

Recommended Cutting Speed for Materials(Dia 25.00-65.00mm)

Grade Feed fn mm/r

Brinell Cutting
Workpiece material hardness Insert speed Drilling dia mm
(HB) Vc m/min
P I C 25.00-43.00 43.01-65.00
C=0.05-0.10% 125 70-130 0.11-0.41 0.14-0.45
C=0.10-0.25% 125 70-130 0.11-0.41 0.14-0.45
Unalloyed steel AP301U(N)
C=0.25-0.55% 150 70-130 0.11-0.41 0.14-0.45
C=0.55-0.80% 170 70-130 0.11-0.41 0.14-0.45
High carbon steel Carbon tool steel 210 AP301U(N) 70-120 0.11-0.41 0.20-0.45

P Non-Hardened 180 55-110 0.11-0.41 0.20-0.45

Low-alloyed steel Tempered 275 AP301U(N) 70-120 0.11-0.41 0.20-0.45
Tempered 350 70-120 0.11-0.41 0.20-0.45
Annealed 200 55-110 0.11-0.38 0.20-0.40
High-alloyed steel AP301U(N)
Hardened tool steel 325 55-110 0.20-0.38 0.20-0.40
Non-alloyed steel 180 55-110 0.11-0.41 0.20-0.45
Cast steel AP301U(N)
Low-alloy（alloy<5%) 200 55-110 0.11-0.41 0.20-0.45
Non-Hardened/Ferritic/martensitic 200 40-110 0.11-0.41 0.20-0.45
Austenitic 200 40-110 0.11-0.41 0.20-0.45
M Stainless steel AP301U(N)
Austenitic, precipitation hardened (PH) 300 40-110 0.11-0.33 0.20-0.35
Austenitic/ferritic, duplex 230 40-80 0.11-0.33 0.20-0.35
Ferritic 200 80-120 0.11-0.38 0.24-0.41
Malleable cast iron AP301U(N)
Pearlitic 260 80-120 0.11-0.38 0.24-0.41
Low tensile strength 180 60-110 0.11-0.38 0.24-0.41
K Grey cast iron AP301U(N)
High tensile strength 245 60-110 0.11-0.38 0.24-0.41
Ferritic 160 50-110 0.11-0.38 0.24-0.41
Nodular cast iron AP301U(N)
Pearlitic 250 50-110 0.11-0.38 0.24-0.41
GGV (CGI) 230
non-aging 30 65-150 0.09-0.33 0.20-0.33
Wrought aluminium alloys AP301U(N)
aged 100 65-150 0.09-0.33 0.20-0.33
≤ 12% Si, non-aging 75 65-150 0.09-0.33 0.20-0.33
Cast aluminium alloys ≤ 12% Si, aged 90 AP301U(N) 65-150 0.09-0.33 0.20-0.33

N > 12% Si, non-aging 130 65-150 0.09-0.33 0.20-0.33

Magnesium alloy 70
Unalloyed, electrolytic copper 100 65-150 0.09-0.33 0.20-0.33
Brass, bronze, red brass 90 65-150 0.09-0.33 0.20-0.33
Copper and copper alloys AP301U(N)
(bronze/brass) Cu alloys, short-chip 110 65-150 0.09-0.33 0.20-0.33
High tensile, Ampco alloy 300 65-150 0.09-0.33 0.20-0.33
Fe-based annealed 200 10-55 0.09-0.30 0.20-0.33
Fe-based hardened 280 10-55 0.09-0.30 0.20-0.33
Heat-resistant alloys Ni or Co-based annealed 250 AP301U(N) 10-55 0.09-0.30 0.20-0.33
Ni or Co-based hardened 350 10-55 0.09-0.30 0.20-0.33
S Ni or Co-based cast 320 10-55 0.09-0.30 0.20-0.33
Pure titanium 200 30-60 0.09-0.30 0.20-0.33
α alloys 375 30-60 0.09-0.30 0.20-0.33
Titanium alloys AP301U(N)
α and β alloys 375 30-60 0.09-0.30 0.20-0.33
β alloys 410 30-60 0.09-0.30 0.20-0.33
Hardened steel Hardened and tempered 43-47 HRC
H
Hardened cast iron 47-60 HRC

*) Insert position-P , I , C
P=peripheral insert , I=intermediate insert, C=center insert

284
Drilling

Recommended Cutting Speed for Materials(Dia ≥63.50mm)

Grade Feed fn mm/r

Brinell Cutting
Workpiece material hardness Insert speed Drilling dia mm
(HB) Vc m/min
P I C ≥ 63.50
C=0.05-0.10% 125 80-100 0.18-0.35
C=0.10-0.25% 125 80-100 0.18-0.35
Unalloyed steel AP301U(N)
C=0.25-0.55% 150 80-100 0.18-0.35
C=0.55-0.80% 170 80-100 0.18-0.35
High carbon steel Carbon tool steel 210 AP301U(N) 70-100 0.18-0.35

P Non-Hardened 180 60-100 0.16-0.35

Low-alloyed steel Tempered 275 AP301U(N) 70-100 0.18-0.30
Tempered 350 70-100 0.18-0.30
Annealed 200 60-100 0.16-0.30
High-alloyed steel AP301U(N)
Hardened tool steel 325 60-100 0.16-0.30
Non-alloyed steel 180 50-100 0.15-0.30
Cast steel AP301U(N)
Low-alloy （alloy<5%) 200 50-100 0.15-0.30
Non-Hardened/Ferritic/martensitic 200 50-90 0.16-0.35
Austenitic 200 50-90 0.16-0.35
M Stainless steel AP301U(N)
Austenitic, precipitation hardened (PH) 300
Austenitic/ferritic, duplex 230
Ferritic 200
Malleable cast iron AP301U(N)
Pearlitic 260
Low tensile strength 180
K Grey cast iron AP301U(N)
High tensile strength 245
Ferritic 160
Nodular cast iron AP301U(N)
Pearlitic 250
GGV (CGI) 230
non-aging 30 65-130 0.10-0.30
Wrought aluminium alloys AP301U(N)
aged 100 65-130 0.10-0.30

Drilling inserts
≤ 12% Si, non-aging 75 65-130 0.10-0.30
Cast aluminium alloys ≤ 12% Si, aged 90 AP301U(N) 65-130 0.10-0.30

N > 12% Si, non-aging 130 65-130 0.10-0.30

Magnesium alloy 70
Unalloyed, electrolytic copper 100 65-130 0.10-0.30
Brass, bronze, red brass 90 65-130 0.10-0.30
Copper and copper alloys AP301U(N)
(bronze/brass) Cu alloys, short-chip 110 65-130 0.10-0.30
High tensile, Ampco alloy 300 65-130 0.10-0.30
Fe-based annealed 200 20-65 0.15-0.30
Fe-based hardened 280 20-65 0.15-0.30
Heat-resistant alloys Ni or Co-based annealed 250 AP301U(N) 20-65 0.15-0.30
Ni or Co-based hardened 350 20-65 0.15-0.30
S Ni or Co-based cast 320
Pure titanium 200 30-100 0.15-0.30
α alloys 375 30-100 0.15-0.30
Titanium alloys AP301U(N)
α and β alloys 375 30-100 0.15-0.30
β alloys 410 30-100 0.15-0.30
Hardened steel Hardened and tempered 43-47 HRC
H
Hardened cast iron 47-60 HRC

*) Insert position-P , I , C
P=peripheral insert , I=intermediate insert, C=center insert

285
 Drilling

Drilling Tools Denomination System

D 1 06 - 03 - 03000 A 1 AP30P1 U
1 2 3 - 4 - 5 6 7 8 9

1-Tool group 2-Generation 3-Tool type

D Drilling 1 06 Universal

4-Drilling depth 5-Cutting diameter 6-Shank type

A DIN 6535 HA
03 ~ 3 x Dc in accordance with DIN 6537K 03000 3.0mm
cylindrical shank

05 ~ 5 x Dc in accordance with DIN 6537L 12100 12.1mm

7-Coolant 8-Grade 9-Application range

0 External coolant AP30P1 U Universal machining P.K.N

1 Internal coolant

Product Overview

External coolant Internal coolant

Machining Machining
application application
1 Through hole 2 Blind hole 1 Through hole 2 Blind hole

Drilling depth 3xDc 5xDc Drilling depth 3xDc 5xDc

Series D106 D106 Series D106 D106
Standard DIN 6537 K DIN 6537 L Standard DIN 6537 K DIN 6537 L
Dia. Range(mm) 3~16 3~16 Dia. Range(mm) 3~16 3~16
Stock items P289-P292 P293-P296 Stock items P297-P300 P301-P304

288
Drilling

Solid Carbide Drill D106 with External Coolant - 3xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-03000A0 AP30P1U 3 14 62 20 36 4 ●

D106-03-03100A0 AP30P1U 3.1 14 62 20 36 4 ●

D106-03-03175A0 AP30P1U 3.175 1/8" 14 62 20 36 4 ○

D106-03-03200A0 AP30P1U 3.2 14 62 20 36 4 ●

D106-03-03250A0 AP30P1U 3.25 14 62 20 36 4 ○

D106-03-03300A0 AP30P1U 3.3 14 62 20 36 4 ●

D106-03-03400A0 AP30P1U 3.4 14 62 20 36 4 ○

D106-03-03500A0 AP30P1U 3.5 14 62 20 36 4 ●

D106-03-03572A0 AP30P1U 3.572 9/64" 14 62 20 36 4 ○

D106-03-03600A0 AP30P1U 3.6 14 62 20 36 4 ●

D106-03-03650A0 AP30P1U 3.65 14 62 20 36 4 ○

D106-03-03700A0 AP30P1U 3.7 14 62 20 36 4 ●

D106-03-03800A0 AP30P1U 3.8 17 66 24 36 4 ○

D106-03-03900A0 AP30P1U 3.9 17 66 24 36 4 ●

D106-03-03969A0 AP30P1U 3.969 5/32" 17 66 24 36 4 ○

D106-03-04000A0 AP30P1U 4 17 66 24 36 4 ●

D106-03-04100A0 AP30P1U 4.1 17 66 24 36 6 ○

D106-03-04200A0 AP30P1U 4.2 17 66 24 36 6 ●

D106-03-04300A0 AP30P1U 4.3 17 66 24 36 6 ○

Solid Carbide Drill

D106-03-04366A0 AP30P1U 4.366 11/64" 17 66 24 36 6 ○

D106-03-04400A0 AP30P1U 4.4 17 66 24 36 6 ○

D106-03-04500A0 AP30P1U 4.5 17 66 24 36 6 ●

D106-03-04600A0 AP30P1U 4.6 17 66 24 36 6 ○

D106-03-04650A0 AP30P1U 4.65 17 66 24 36 6 ○

D106-03-04700A0 AP30P1U 4.7 17 66 24 36 6 ○

D106-03-04763A0 AP30P1U 4.763 3/16" 20 66 28 36 6 ○

D106-03-04800A0 AP30P1U 4.8 20 66 28 36 6 ●

D106-03-04900A0 AP30P1U 4.9 20 66 28 36 6 ●

D106-03-05000A0 AP30P1U 5 20 66 28 36 6 ●

D106-03-05100A0 AP30P1U 5.1 20 66 28 36 6 ●

D106-03-05159A0 AP30P1U 5.159 13/64" 20 66 28 36 6 ○

D106-03-05200A0 AP30P1U 5.2 20 66 28 36 6 ●

D106-03-05300A0 AP30P1U 5.3 20 66 28 36 6 ○

D106-03-05400A0 AP30P1U 5.4 20 66 28 36 6 ○

D106-03-05500A0 AP30P1U 5.5 20 66 28 36 6 ●

D106-03-05550A0 AP30P1U 5.55 20 66 28 36 6 ○

Marked：● Stock available ○ Non-stocked standard

289
 Drilling

Solid Carbide Drill D106 with External Coolant - 3xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-05556A0 AP30P1U 5.556 7/32" 20 66 28 36 6 ○

D106-03-05600A0 AP30P1U 5.6 20 66 28 36 6 ○

D106-03-05700A0 AP30P1U 5.7 20 66 28 36 6 ○

D106-03-05800A0 AP30P1U 5.8 20 66 28 36 6 ●

D106-03-05900A0 AP30P1U 5.9 20 66 28 36 6 ●

D106-03-05953A0 AP30P1U 5.953 15/64" 20 66 28 36 6 ○

D106-03-06000A0 AP30P1U 6 20 66 28 36 6 ●

D106-03-06100A0 AP30P1U 6.1 24 79 41 36 8 ○

D106-03-06200A0 AP30P1U 6.2 24 79 41 36 8 ○

D106-03-06300A0 AP30P1U 6.3 24 79 41 36 8 ○

D106-03-06350A0 AP30P1U 6.35 1/4" 24 79 41 36 8 ○

D106-03-06400A0 AP30P1U 6.4 24 79 41 36 8 ○

D106-03-06500A0 AP30P1U 6.5 24 79 41 36 8 ●

D106-03-06600A0 AP30P1U 6.6 24 79 41 36 8 ○

D106-03-06700A0 AP30P1U 6.7 24 79 41 36 8 ○

D106-03-06747A0 AP30P1U 6.747 17/64" 24 79 41 36 8 ○

D106-03-06800A0 AP30P1U 6.8 24 79 41 36 8 ●

D106-03-06900A0 AP30P1U 6.9 24 79 41 36 8 ●

D106-03-07000A0 AP30P1U 7 24 79 41 36 8 ●

D106-03-07100A0 AP30P1U 7.1 29 79 41 36 8 ○

D106-03-07144A0 AP30P1U 7.144 9/32" 29 79 41 36 8 ○

D106-03-07200A0 AP30P1U 7.2 29 79 41 36 8 ○

D106-03-07300A0 AP30P1U 7.3 29 79 41 36 8 ○

D106-03-07400A0 AP30P1U 7.4 29 79 41 36 8 ●

D106-03-07500A0 AP30P1U 7.5 29 79 41 36 8 ●

D106-03-07541A0 AP30P1U 7.541 19/64" 29 79 41 36 8 ○

D106-03-07550A0 AP30P1U 7.55 29 79 41 36 8 ○

D106-03-07600A0 AP30P1U 7.6 29 79 41 36 8 ○

D106-03-07700A0 AP30P1U 7.7 29 79 41 36 8 ○

D106-03-07800A0 AP30P1U 7.8 29 79 41 36 8 ●

D106-03-07900A0 AP30P1U 7.9 29 79 41 36 8 ●

D106-03-07938A0 AP30P1U 7.938 5/16" 29 79 41 36 8 ○

D106-03-08000A0 AP30P1U 8 29 79 41 36 8 ●

D106-03-08100A0 AP30P1U 8.1 35 89 47 40 10 ○

D106-03-08200A0 AP30P1U 8.2 35 89 47 40 10 ○

D106-03-08300A0 AP30P1U 8.3 35 89 47 40 10 ○

D106-03-08334A0 AP30P1U 8.334 21/64" 35 89 47 40 10 ○

D106-03-08400A0 AP30P1U 8.4 35 89 47 40 10 ○

D106-03-08500A0 AP30P1U 8.5 35 89 47 40 10 ●

D106-03-08600A0 AP30P1U 8.6 35 89 47 40 10 ●

D106-03-08700A0 AP30P1U 8.7 35 89 47 40 10 ○

D106-03-08731A0 AP30P1U 8.731 11/32" 35 89 47 40 10 ○

D106-03-08800A0 AP30P1U 8.8 35 89 47 40 10 ●

D106-03-08900A0 AP30P1U 8.9 35 89 47 40 10 ●

Marked：● Stock available ○ Non-stocked standard

290
Drilling

Solid Carbide Drill D106 with External Coolant - 3xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-09000A0 AP30P1U 9 35 89 47 40 10 ●

D106-03-09100A0 AP30P1U 9.1 35 89 47 40 10 ○

D106-03-09128A0 AP30P1U 9.128 23/64" 35 89 47 40 10 ○

D106-03-09200A0 AP30P1U 9.2 35 89 47 40 10 ○

D106-03-09300A0 AP30P1U 9.3 35 89 47 40 10 ●

D106-03-09400A0 AP30P1U 9.4 35 89 47 40 10 ○

D106-03-09500A0 AP30P1U 9.5 35 89 47 40 10 ○

D106-03-09525A0 AP30P1U 9.525 3/8" 35 89 47 40 10 ○

D106-03-09550A0 AP30P1U 9.55 35 89 47 40 10 ○

D106-03-09600A0 AP30P1U 9.6 35 89 47 40 10 ○

D106-03-09700A0 AP30P1U 9.7 35 89 47 40 10 ○

D106-03-09800A0 AP30P1U 9.8 35 89 47 40 10 ●

D106-03-09900A0 AP30P1U 9.9 35 89 47 40 10 ●

D106-03-09922A0 AP30P1U 9.922 25/64" 35 89 47 40 10 ○

D106-03-10000A0 AP30P1U 10 35 89 47 40 10 ●

D106-03-10100A0 AP30P1U 10.1 40 102 55 45 12 ●

D106-03-10200A0 AP30P1U 10.2 40 102 55 45 12 ●

D106-03-10300A0 AP30P1U 10.3 40 102 55 45 12 ●

D106-03-10319A0 AP30P1U 10.319 13/32" 40 102 55 45 12 ○

Solid Carbide Drill

D106-03-10400A0 AP30P1U 10.4 40 102 55 45 12 ○

D106-03-10500A0 AP30P1U 10.5 40 102 55 45 12 ●

D106-03-10600A0 AP30P1U 10.6 40 102 55 45 12 ●

D106-03-10700A0 AP30P1U 10.7 40 102 55 45 12 ○

D106-03-10716A0 AP30P1U 10.716 27/64" 40 102 55 45 12 ○

D106-03-10800A0 AP30P1U 10.8 40 102 55 45 12 ●

D106-03-10900A0 AP30P1U 10.9 40 102 55 45 12 ○

D106-03-11000A0 AP30P1U 11 40 102 55 45 12 ●

D106-03-11100A0 AP30P1U 11.1 40 102 55 45 12 ○

D106-03-11113A0 AP30P1U 11.113 7/16" 40 102 55 45 12 ○

D106-03-11200A0 AP30P1U 11.2 40 102 55 45 12 ○

D106-03-11300A0 AP30P1U 11.3 40 102 55 45 12 ○

D106-03-11400A0 AP30P1U 11.4 40 102 55 45 12 ○

D106-03-11500A0 AP30P1U 11.5 40 102 55 45 12 ○

D106-03-11509A0 AP30P1U 11.509 29/64" 40 102 55 45 12 ○

D106-03-11550A0 AP30P1U 11.55 40 102 55 45 12 ○

D106-03-11600A0 AP30P1U 11.6 40 102 55 45 12 ○

D106-03-11700A0 AP30P1U 11.7 40 102 55 45 12 ○

D106-03-11800A0 AP30P1U 11.8 40 102 55 45 12 ●

D106-03-11900A0 AP30P1U 11.9 40 102 55 45 12 ○

D106-03-11906A0 AP30P1U 11.906 15/32" 40 102 55 45 12 ○

D106-03-12000A0 AP30P1U 12 40 102 55 45 12 ●

D106-03-12100A0 AP30P1U 12.1 43 107 60 45 14 ○

D106-03-12200A0 AP30P1U 12.2 43 107 60 45 14 ○

D106-03-12250A0 AP30P1U 12.25 43 107 60 45 14 ○

Marked：● Stock available ○ Non-stocked standard

291
 Drilling

Solid Carbide Drill D106 with External Coolant - 3xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-12300A0 AP30P1U 12.3 43 107 60 45 14 ○

D106-03-12303A0 AP30P1U 12.303 31/64" 43 107 60 45 14 ○

D106-03-12400A0 AP30P1U 12.4 43 107 60 45 14 ○

D106-03-12500A0 AP30P1U 12.5 43 107 60 45 14 ●

D106-03-12600A0 AP30P1U 12.6 43 107 60 45 14 ○

D106-03-12700A0 AP30P1U 12.7 1/2" 43 107 60 45 14 ○

D106-03-12750A0 AP30P1U 12.75 43 107 60 45 14 ○

D106-03-12800A0 AP30P1U 12.8 43 107 60 45 14 ○

D106-03-12900A0 AP30P1U 12.9 43 107 60 45 14 ○

D106-03-13000A0 AP30P1U 13 43 107 60 45 14 ●

D106-03-13100A0 AP30P1U 13.1 43 107 60 45 14 ○

D106-03-13200A0 AP30P1U 13.2 43 107 60 45 14 ●

D106-03-13300A0 AP30P1U 13.3 43 107 60 45 14 ○

D106-03-13400A0 AP30P1U 13.4 43 107 60 45 14 ○

D106-03-13494A0 AP30P1U 13.494 17/32" 43 107 60 45 14 ○

D106-03-13500A0 AP30P1U 13.5 43 107 60 45 14 ○

D106-03-13600A0 AP30P1U 13.6 43 107 60 45 14 ○

D106-03-13700A0 AP30P1U 13.7 43 107 60 45 14 ○

D106-03-13800A0 AP30P1U 13.8 43 107 60 45 14 ○

D106-03-13900A0 AP30P1U 13.9 43 107 60 45 14 ○

D106-03-14000A0 AP30P1U 14 43 107 60 45 14 ●

D106-03-14100A0 AP30P1U 14.1 45 115 65 48 16 ●

D106-03-14200A0 AP30P1U 14.2 45 115 65 48 16 ●

D106-03-14288A0 AP30P1U 14.288 9/16" 45 115 65 48 16 ○

D106-03-14300A0 AP30P1U 14.3 45 115 65 48 16 ○

D106-03-14400A0 AP30P1U 14.4 45 115 65 48 16 ○

D106-03-14500A0 AP30P1U 14.5 45 115 65 48 16 ●

D106-03-14600A0 AP30P1U 14.6 45 115 65 48 16 ●

D106-03-14700A0 AP30P1U 14.7 45 115 65 48 16 ●

D106-03-14750A0 AP30P1U 14.75 45 115 65 48 16 ○

D106-03-14800A0 AP30P1U 14.8 45 115 65 48 16 ○

D106-03-15000A0 AP30P1U 15 45 115 65 48 16 ●

D106-03-15100A0 AP30P1U 15.1 45 115 65 48 16 ○

D106-03-15200A0 AP30P1U 15.2 45 115 65 48 16 ○

D106-03-15300A0 AP30P1U 15.3 45 115 65 48 16 ○

D106-03-15500A0 AP30P1U 15.5 45 115 65 48 16 ●

D106-03-15600A0 AP30P1U 15.6 45 115 65 48 16 ○

D106-03-15700A0 AP30P1U 15.7 45 115 65 48 16 ●

D106-03-15800A0 AP30P1U 15.8 45 115 65 48 16 ●

D106-03-15875A0 AP30P1U 15.875 5/8" 45 115 65 48 16 ○

D106-03-15900A0 AP30P1U 15.9 45 115 65 48 16 ○

D106-03-16000A0 AP30P1U 16 45 115 65 48 16 ●

Marked：● Stock available ○ Non-stocked standard

292
Drilling

Solid Carbide Drill D106 with External Coolant - 5xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-03000A0 AP30P1U 3 23 66 28 36 4 ●

D106-05-03100A0 AP30P1U 3.1 23 66 28 36 4 ●

D106-05-03175A0 AP30P1U 3.175 1/8" 23 66 28 36 4 ○

D106-05-03200A0 AP30P1U 3.2 23 66 28 36 4 ●

D106-05-03250A0 AP30P1U 3.25 23 66 28 36 4 ○

D106-05-03300A0 AP30P1U 3.3 23 66 28 36 4 ●

D106-05-03400A0 AP30P1U 3.4 23 66 28 36 4 ○

D106-05-03500A0 AP30P1U 3.5 23 66 28 36 4 ●

D106-05-03572A0 AP30P1U 3.572 9/64" 23 66 28 36 4 ○

D106-05-03600A0 AP30P1U 3.6 23 66 28 36 4 ●

D106-05-03650A0 AP30P1U 3.65 23 66 28 36 4 ○

D106-05-03700A0 AP30P1U 3.7 23 66 28 36 4 ●

D106-05-03800A0 AP30P1U 3.8 29 74 36 36 4 ○

D106-05-03900A0 AP30P1U 3.9 29 74 36 36 4 ●

D106-05-03969A0 AP30P1U 3.969 5/32" 29 74 36 36 4 ○

D106-05-04000A0 AP30P1U 4 29 74 36 36 4 ●

D106-05-04100A0 AP30P1U 4.1 29 74 36 36 6 ○

D106-05-04200A0 AP30P1U 4.2 29 74 36 36 6 ●

D106-05-04300A0 AP30P1U 4.3 29 74 36 36 6 ○

Solid Carbide Drill

D106-05-04366A0 AP30P1U 4.366 11/64" 29 74 36 36 6 ○

D106-05-04400A0 AP30P1U 4.4 29 74 36 36 6 ○

D106-05-04500A0 AP30P1U 4.5 29 74 36 36 6 ●

D106-05-04600A0 AP30P1U 4.6 29 74 36 36 6 ○

D106-05-04650A0 AP30P1U 4.65 29 74 36 36 6 ○

D106-05-04700A0 AP30P1U 4.7 29 74 36 36 6 ○

D106-05-04763A0 AP30P1U 4.763 3/16" 35 82 44 36 6 ○

D106-05-04800A0 AP30P1U 4.8 35 82 44 36 6 ●

D106-05-04900A0 AP30P1U 4.9 35 82 44 36 6 ●

D106-05-05000A0 AP30P1U 5 35 82 44 36 6 ●

D106-05-05100A0 AP30P1U 5.1 35 82 44 36 6 ●

D106-05-05159A0 AP30P1U 5.159 13/64" 35 82 44 36 6 ○

D106-05-05200A0 AP30P1U 5.2 35 82 44 36 6 ●

D106-05-05300A0 AP30P1U 5.3 35 82 44 36 6 ○

D106-05-05400A0 AP30P1U 5.4 35 82 44 36 6 ○

D106-05-05500A0 AP30P1U 5.5 35 82 44 36 6 ●

D106-05-05550A0 AP30P1U 5.55 35 82 44 36 6 ○

Marked：● Stock available ○ Non-stocked standard

293
 Drilling

Solid Carbide Drill D106 with External Coolant - 5xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-05556A0 AP30P1U 5.556 7/32" 35 82 44 36 6 ○

D106-05-05600A0 AP30P1U 5.6 35 82 44 36 6 ○

D106-05-05700A0 AP30P1U 5.7 35 82 44 36 6 ○

D106-05-05800A0 AP30P1U 5.8 35 82 44 36 6 ●

D106-05-05900A0 AP30P1U 5.9 35 82 44 36 6 ●

D106-05-05953A0 AP30P1U 5.953 15/64" 35 82 44 36 6 ○

D106-05-06000A0 AP30P1U 6 35 82 44 36 6 ●

D106-05-06100A0 AP30P1U 6.1 43 91 53 36 8 ○

D106-05-06200A0 AP30P1U 6.2 43 91 53 36 8 ○

D106-05-06300A0 AP30P1U 6.3 43 91 53 36 8 ○

D106-05-06350A0 AP30P1U 6.35 1/4" 43 91 53 36 8 ○

D106-05-06400A0 AP30P1U 6.4 43 91 53 36 8 ○

D106-05-06500A0 AP30P1U 6.5 43 91 53 36 8 ●

D106-05-06600A0 AP30P1U 6.6 43 91 53 36 8 ○

D106-05-06700A0 AP30P1U 6.7 43 91 53 36 8 ○

D106-05-06747A0 AP30P1U 6.747 17/64" 43 91 53 36 8 ○

D106-05-06800A0 AP30P1U 6.8 43 91 53 36 8 ●

D106-05-06900A0 AP30P1U 6.9 43 91 53 36 8 ●

D106-05-07000A0 AP30P1U 7 43 91 53 36 8 ●

D106-05-07100A0 AP30P1U 7.1 43 91 53 36 8 ○

D106-05-07144A0 AP30P1U 7.144 9/32" 43 91 53 36 8 ○

D106-05-07200A0 AP30P1U 7.2 43 91 53 36 8 ○

D106-05-07300A0 AP30P1U 7.3 43 91 53 36 8 ○

D106-05-07400A0 AP30P1U 7.4 43 91 53 36 8 ●

D106-05-07500A0 AP30P1U 7.5 43 91 53 36 8 ●

D106-05-07541A0 AP30P1U 7.541 19/64" 43 91 53 36 8 ○

D106-05-07550A0 AP30P1U 7.55 43 91 53 36 8 ○

D106-05-07600A0 AP30P1U 7.6 43 91 53 36 8 ○

D106-05-07700A0 AP30P1U 7.7 43 91 53 36 8 ○

D106-05-07800A0 AP30P1U 7.8 43 91 53 36 8 ●

D106-05-07900A0 AP30P1U 7.9 43 91 53 36 8 ●

D106-05-07938A0 AP30P1U 7.938 5/16" 43 91 53 36 8 ○

D106-05-08000A0 AP30P1U 8 43 91 53 36 8 ●

D106-05-08100A0 AP30P1U 8.1 49 103 61 40 10 ○

D106-05-08200A0 AP30P1U 8.2 49 103 61 40 10 ○

D106-05-08300A0 AP30P1U 8.3 49 103 61 40 10 ○

D106-05-08334A0 AP30P1U 8.334 21/64" 49 103 61 40 10 ○

D106-05-08400A0 AP30P1U 8.4 49 103 61 40 10 ○

D106-05-08500A0 AP30P1U 8.5 49 103 61 40 10 ●

D106-05-08600A0 AP30P1U 8.6 49 103 61 40 10 ●

D106-05-08700A0 AP30P1U 8.7 49 103 61 40 10 ○

D106-05-08731A0 AP30P1U 8.731 11/32" 49 103 61 40 10 ○

D106-05-08800A0 AP30P1U 8.8 49 103 61 40 10 ●

D106-05-08900A0 AP30P1U 8.9 49 103 61 40 10 ●

Marked：● Stock available ○ Non-stocked standard

294
Drilling

Solid Carbide Drill D106 with External Coolant - 5xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-09000A0 AP30P1U 9 49 103 61 40 10 ●

D106-05-09100A0 AP30P1U 9.1 49 103 61 40 10 ○

D106-05-09128A0 AP30P1U 9.128 23/64" 49 103 61 40 10 ○

D106-05-09200A0 AP30P1U 9.2 49 103 61 40 10 ○

D106-05-09300A0 AP30P1U 9.3 49 103 61 40 10 ●

D106-05-09400A0 AP30P1U 9.4 49 103 61 40 10 ○

D106-05-09500A0 AP30P1U 9.5 49 103 61 40 10 ○

D106-05-09525A0 AP30P1U 9.525 3/8" 49 103 61 40 10 ○

D106-05-09550A0 AP30P1U 9.55 49 103 61 40 10 ○

D106-05-09600A0 AP30P1U 9.6 49 103 61 40 10 ○

D106-05-09700A0 AP30P1U 9.7 49 103 61 40 10 ○

D106-05-09800A0 AP30P1U 9.8 49 103 61 40 10 ●

D106-05-09900A0 AP30P1U 9.9 49 103 61 40 10 ●

D106-05-09922A0 AP30P1U 9.922 25/64" 49 103 61 40 10 ○

D106-05-10000A0 AP30P1U 10 49 103 61 40 10 ●

D106-05-10100A0 AP30P1U 10.1 56 118 71 45 12 ●

D106-05-10200A0 AP30P1U 10.2 56 118 71 45 12 ●

D106-05-10300A0 AP30P1U 10.3 56 118 71 45 12 ●

D106-05-10319A0 AP30P1U 10.319 13/32" 56 118 71 45 12 ○

Solid Carbide Drill

D106-05-10400A0 AP30P1U 10.4 56 118 71 45 12 ○

D106-05-10500A0 AP30P1U 10.5 56 118 71 45 12 ●

D106-05-10600A0 AP30P1U 10.6 56 118 71 45 12 ●

D106-05-10700A0 AP30P1U 10.7 56 118 71 45 12 ○

D106-05-10716A0 AP30P1U 10.716 27/64" 56 118 71 45 12 ○

D106-05-10800A0 AP30P1U 10.8 56 118 71 45 12 ●

D106-05-10900A0 AP30P1U 10.9 56 118 71 45 12 ○

D106-05-11000A0 AP30P1U 11 56 118 71 45 12 ●

D106-05-11100A0 AP30P1U 11.1 56 118 71 45 12 ○

D106-05-11113A0 AP30P1U 11.113 7/16" 56 118 71 45 12 ○

D106-05-11200A0 AP30P1U 11.2 56 118 71 45 12 ○

D106-05-11300A0 AP30P1U 11.3 56 118 71 45 12 ○

D106-05-11400A0 AP30P1U 11.4 56 118 71 45 12 ○

D106-05-11500A0 AP30P1U 11.5 56 118 71 45 12 ○

D106-05-11509A0 AP30P1U 11.509 29/64" 56 118 71 45 12 ○

D106-05-11550A0 AP30P1U 11.55 56 118 71 45 12 ○

D106-05-11600A0 AP30P1U 11.6 56 118 71 45 12 ○

D106-05-11700A0 AP30P1U 11.7 56 118 71 45 12 ○

D106-05-11800A0 AP30P1U 11.8 56 118 71 45 12 ●

D106-05-11900A0 AP30P1U 11.9 56 118 71 45 12 ○

D106-05-11906A0 AP30P1U 11.906 15/32" 56 118 71 45 12 ○

D106-05-12000A0 AP30P1U 12 56 118 71 45 12 ●

D106-05-12100A0 AP30P1U 12.1 60 124 77 45 14 ○

D106-05-12200A0 AP30P1U 12.2 60 124 77 45 14 ○

D106-05-12250A0 AP30P1U 12.25 60 124 77 45 14 ○

Marked：● Stock available ○ Non-stocked standard

295
 Drilling

Solid Carbide Drill D106 with External Coolant - 5xDc P M S K H N O

●● ●● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-12300A0 AP30P1U 12.3 60 124 77 45 14 ○

D106-05-12303A0 AP30P1U 12.303 31/64" 60 124 77 45 14 ○

D106-05-12400A0 AP30P1U 12.4 60 124 77 45 14 ○

D106-05-12500A0 AP30P1U 12.5 60 124 77 45 14 ●

D106-05-12600A0 AP30P1U 12.6 60 124 77 45 14 ○

D106-05-12700A0 AP30P1U 12.7 1/2" 60 124 77 45 14 ○

D106-05-12750A0 AP30P1U 12.75 60 124 77 45 14 ○

D106-05-12800A0 AP30P1U 12.8 60 124 77 45 14 ○

D106-05-12900A0 AP30P1U 12.9 60 124 77 45 14 ○

D106-05-13000A0 AP30P1U 13 60 124 77 45 14 ●

D106-05-13100A0 AP30P1U 13.1 60 124 77 45 14 ○

D106-05-13200A0 AP30P1U 13.2 60 124 77 45 14 ●

D106-05-13300A0 AP30P1U 13.3 60 124 77 45 14 ○

D106-05-13400A0 AP30P1U 13.4 60 124 77 45 14 ○

D106-05-13494A0 AP30P1U 13.494 17/32" 60 124 77 45 14 ○

D106-05-13500A0 AP30P1U 13.5 60 124 77 45 14 ○

D106-05-13600A0 AP30P1U 13.6 60 124 77 45 14 ○

D106-05-13700A0 AP30P1U 13.7 60 124 77 45 14 ●

D106-05-13800A0 AP30P1U 13.8 60 124 77 45 14 ○

D106-05-13900A0 AP30P1U 13.9 60 124 77 45 14 ○

D106-05-14000A0 AP30P1U 14 60 124 77 45 14 ●

D106-05-14100A0 AP30P1U 14.1 63 133 83 48 16 ●

D106-05-14200A0 AP30P1U 14.2 63 133 83 48 16 ●

D106-05-14288A0 AP30P1U 14.288 9/16" 63 133 83 48 16 ○

D106-05-14300A0 AP30P1U 14.3 63 133 83 48 16 ○

D106-05-14400A0 AP30P1U 14.4 63 133 83 48 16 ○

D106-05-14500A0 AP30P1U 14.5 63 133 83 48 16 ●

D106-05-14600A0 AP30P1U 14.6 63 133 83 48 16 ●

D106-05-14700A0 AP30P1U 14.7 63 133 83 48 16 ●

D106-05-14750A0 AP30P1U 14.75 63 133 83 48 16 ○

D106-05-14800A0 AP30P1U 14.8 63 133 83 48 16 ○

D106-05-15000A0 AP30P1U 15 63 133 83 48 16 ●

D106-05-15100A0 AP30P1U 15.1 63 133 83 48 16 ○

D106-05-15200A0 AP30P1U 15.2 63 133 83 48 16 ○

D106-05-15300A0 AP30P1U 15.3 63 133 83 48 16 ○

D106-05-15500A0 AP30P1U 15.5 63 133 83 48 16 ●

D106-05-15600A0 AP30P1U 15.6 63 133 83 48 16 ○

D106-05-15700A0 AP30P1U 15.7 63 133 83 48 16 ●

D106-05-15800A0 AP30P1U 15.8 63 133 83 48 16 ●

D106-05-15875A0 AP30P1U 15.875 5/8" 63 133 83 48 16 ○

D106-05-15900A0 AP30P1U 15.9 63 133 83 48 16 ○

D106-05-16000A0 AP30P1U 16 63 133 83 48 16 ●

Marked：● Stock available ○ Non-stocked standard

296
Drilling

Solid Carbide Drill D106 with Internal Coolant - 3xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-03000A1 AP30P1U 3 14 62 20 36 4 ●

D106-03-03100A1 AP30P1U 3.1 14 62 20 36 4 ●

D106-03-03175A1 AP30P1U 3.175 1/8" 14 62 20 36 4 ○

D106-03-03200A1 AP30P1U 3.2 14 62 20 36 4 ●

D106-03-03250A1 AP30P1U 3.25 14 62 20 36 4 ○

D106-03-03300A1 AP30P1U 3.3 14 62 20 36 4 ●

D106-03-03400A1 AP30P1U 3.4 14 62 20 36 4 ○

D106-03-03500A1 AP30P1U 3.5 14 62 20 36 4 ●

D106-03-03572A1 AP30P1U 3.572 9/64" 14 62 20 36 4 ○

D106-03-03600A1 AP30P1U 3.6 14 62 20 36 4 ●

D106-03-03650A1 AP30P1U 3.65 14 62 20 36 4 ○

D106-03-03700A1 AP30P1U 3.7 14 62 20 36 4 ●

D106-03-03800A1 AP30P1U 3.8 17 66 24 36 4 ○

D106-03-03900A1 AP30P1U 3.9 17 66 24 36 4 ●

D106-03-03969A1 AP30P1U 3.969 5/32" 17 66 24 36 4 ○

D106-03-04000A1 AP30P1U 4 17 66 24 36 4 ●

D106-03-04100A1 AP30P1U 4.1 17 66 24 36 6 ○

D106-03-04200A1 AP30P1U 4.2 17 66 24 36 6 ●

D106-03-04300A1 AP30P1U 4.3 17 66 24 36 6 ○

Solid Carbide Drill

D106-03-04366A1 AP30P1U 4.366 11/64" 17 66 24 36 6 ○

D106-03-04400A1 AP30P1U 4.4 17 66 24 36 6 ○

D106-03-04500A1 AP30P1U 4.5 17 66 24 36 6 ●

D106-03-04600A1 AP30P1U 4.6 17 66 24 36 6 ○

D106-03-04650A1 AP30P1U 4.65 17 66 24 36 6 ○

D106-03-04700A1 AP30P1U 4.7 17 66 24 36 6 ○

D106-03-04763A1 AP30P1U 4.763 3/16" 20 66 28 36 6 ○

D106-03-04800A1 AP30P1U 4.8 20 66 28 36 6 ●

D106-03-04900A1 AP30P1U 4.9 20 66 28 36 6 ●

D106-03-05000A1 AP30P1U 5 20 66 28 36 6 ●

D106-03-05100A1 AP30P1U 5.1 20 66 28 36 6 ●

D106-03-05159A1 AP30P1U 5.159 13/64" 20 66 28 36 6 ○

D106-03-05200A1 AP30P1U 5.2 20 66 28 36 6 ●

D106-03-05300A1 AP30P1U 5.3 20 66 28 36 6 ○

D106-03-05400A1 AP30P1U 5.4 20 66 28 36 6 ○

D106-03-05500A1 AP30P1U 5.5 20 66 28 36 6 ●

D106-03-05550A1 AP30P1U 5.55 20 66 28 36 6 ○

Marked：● Stock available ○ Non-stocked standard

297
 Drilling

Solid Carbide Drill D106 with Internal Coolant - 3xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-05556A1 AP30P1U 5.556 7/32" 20 66 28 36 6 ○

D106-03-05600A1 AP30P1U 5.6 20 66 28 36 6 ○

D106-03-05700A1 AP30P1U 5.7 20 66 28 36 6 ○

D106-03-05800A1 AP30P1U 5.8 20 66 28 36 6 ●

D106-03-05900A1 AP30P1U 5.9 20 66 28 36 6 ●

D106-03-05953A1 AP30P1U 5.953 15/64" 20 66 28 36 6 ○

D106-03-06000A1 AP30P1U 6 20 66 28 36 6 ●

D106-03-06100A1 AP30P1U 6.1 24 79 41 36 8 ○

D106-03-06200A1 AP30P1U 6.2 24 79 41 36 8 ○

D106-03-06300A1 AP30P1U 6.3 24 79 41 36 8 ○

D106-03-06350A1 AP30P1U 6.35 1/4" 24 79 41 36 8 ○

D106-03-06400A1 AP30P1U 6.4 24 79 41 36 8 ○

D106-03-06500A1 AP30P1U 6.5 24 79 41 36 8 ●

D106-03-06600A1 AP30P1U 6.6 24 79 41 36 8 ○

D106-03-06700A1 AP30P1U 6.7 24 79 41 36 8 ○

D106-03-06747A1 AP30P1U 6.747 17/64" 24 79 41 36 8 ○

D106-03-06800A1 AP30P1U 6.8 24 79 41 36 8 ●

D106-03-06900A1 AP30P1U 6.9 24 79 41 36 8 ●

D106-03-07000A1 AP30P1U 7 24 79 41 36 8 ●

D106-03-07100A1 AP30P1U 7.1 29 79 41 36 8 ○

D106-03-07144A1 AP30P1U 7.144 9/32" 29 79 41 36 8 ○

D106-03-07200A1 AP30P1U 7.2 29 79 41 36 8 ○

D106-03-07300A1 AP30P1U 7.3 29 79 41 36 8 ○

D106-03-07400A1 AP30P1U 7.4 29 79 41 36 8 ●

D106-03-07500A1 AP30P1U 7.5 29 79 41 36 8 ●

D106-03-07541A1 AP30P1U 7.541 19/64" 29 79 41 36 8 ○

D106-03-07550A1 AP30P1U 7.55 29 79 41 36 8 ○

D106-03-07600A1 AP30P1U 7.6 29 79 41 36 8 ○

D106-03-07700A1 AP30P1U 7.7 29 79 41 36 8 ○

D106-03-07800A1 AP30P1U 7.8 29 79 41 36 8 ●

D106-03-07900A1 AP30P1U 7.9 29 79 41 36 8 ●

D106-03-07938A1 AP30P1U 7.938 5/16" 29 79 41 36 8 ○

D106-03-08000A1 AP30P1U 8 29 79 41 36 8 ●

D106-03-08100A1 AP30P1U 8.1 35 89 47 40 10 ○

D106-03-08200A1 AP30P1U 8.2 35 89 47 40 10 ○

D106-03-08300A1 AP30P1U 8.3 35 89 47 40 10 ○

D106-03-08334A1 AP30P1U 8.334 21/64" 35 89 47 40 10 ○

D106-03-08400A1 AP30P1U 8.4 35 89 47 40 10 ○

D106-03-08500A1 AP30P1U 8.5 35 89 47 40 10 ●

D106-03-08600A1 AP30P1U 8.6 35 89 47 40 10 ●

D106-03-08700A1 AP30P1U 8.7 35 89 47 40 10 ○

D106-03-08731A1 AP30P1U 8.731 11/32" 35 89 47 40 10 ○

D106-03-08800A1 AP30P1U 8.8 35 89 47 40 10 ●

D106-03-08900A1 AP30P1U 8.9 35 89 47 40 10 ●

Marked：● Stock available ○ Non-stocked standard

298
Drilling

Solid Carbide Drill D106 with Internal Coolant - 3xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-09000A1 AP30P1U 9 35 89 47 40 10 ●

D106-03-09100A1 AP30P1U 9.1 35 89 47 40 10 ○

D106-03-09128A1 AP30P1U 9.128 23/64" 35 89 47 40 10 ○

D106-03-09200A1 AP30P1U 9.2 35 89 47 40 10 ○

D106-03-09300A1 AP30P1U 9.3 35 89 47 40 10 ●

D106-03-09400A1 AP30P1U 9.4 35 89 47 40 10 ○

D106-03-09500A1 AP30P1U 9.5 35 89 47 40 10 ○

D106-03-09525A1 AP30P1U 9.525 3/8" 35 89 47 40 10 ○

D106-03-09550A1 AP30P1U 9.55 35 89 47 40 10 ○

D106-03-09600A1 AP30P1U 9.6 35 89 47 40 10 ○

D106-03-09700A1 AP30P1U 9.7 35 89 47 40 10 ○

D106-03-09800A1 AP30P1U 9.8 35 89 47 40 10 ●

D106-03-09900A1 AP30P1U 9.9 35 89 47 40 10 ●

D106-03-09922A1 AP30P1U 9.922 25/64" 35 89 47 40 10 ○

D106-03-10000A1 AP30P1U 10 35 89 47 40 10 ●

D106-03-10100A1 AP30P1U 10.1 40 102 55 45 12 ●

D106-03-10200A1 AP30P1U 10.2 40 102 55 45 12 ●

D106-03-10300A1 AP30P1U 10.3 40 102 55 45 12 ●

D106-03-10319A1 AP30P1U 10.319 13/32" 40 102 55 45 12 ○

Solid Carbide Drill

D106-03-10400A1 AP30P1U 10.4 40 102 55 45 12 ○

D106-03-10500A1 AP30P1U 10.5 40 102 55 45 12 ●

D106-03-10600A1 AP30P1U 10.6 40 102 55 45 12 ●

D106-03-10700A1 AP30P1U 10.7 40 102 55 45 12 ○

D106-03-10716A1 AP30P1U 10.716 27/64" 40 102 55 45 12 ○

D106-03-10800A1 AP30P1U 10.8 40 102 55 45 12 ●

D106-03-10900A1 AP30P1U 10.9 40 102 55 45 12 ○

D106-03-11000A1 AP30P1U 11 40 102 55 45 12 ●

D106-03-11100A1 AP30P1U 11.1 40 102 55 45 12 ○

D106-03-11113A1 AP30P1U 11.113 7/16" 40 102 55 45 12 ○

D106-03-11200A1 AP30P1U 11.2 40 102 55 45 12 ○

D106-03-11300A1 AP30P1U 11.3 40 102 55 45 12 ○

D106-03-11400A1 AP30P1U 11.4 40 102 55 45 12 ○

D106-03-11500A1 AP30P1U 11.5 40 102 55 45 12 ○

D106-03-11509A1 AP30P1U 11.509 29/64" 40 102 55 45 12 ○

D106-03-11550A1 AP30P1U 11.55 40 102 55 45 12 ○

D106-03-11600A1 AP30P1U 11.6 40 102 55 45 12 ○

D106-03-11700A1 AP30P1U 11.7 40 102 55 45 12 ○

D106-03-11800A1 AP30P1U 11.8 40 102 55 45 12 ●

D106-03-11900A1 AP30P1U 11.9 40 102 55 45 12 ○

D106-03-11906A1 AP30P1U 11.906 15/32" 40 102 55 45 12 ○

D106-03-12000A1 AP30P1U 12 40 102 55 45 12 ●

D106-03-12100A1 AP30P1U 12.1 43 107 60 45 14 ○

D106-03-12200A1 AP30P1U 12.2 43 107 60 45 14 ○

D106-03-12250A1 AP30P1U 12.25 43 107 60 45 14 ○

Marked：● Stock available ○ Non-stocked standard

299
 Drilling

Solid Carbide Drill D106 with Internal Coolant - 3xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-03-12300A1 AP30P1U 12.3 43 107 60 45 14 ○

D106-03-12303A1 AP30P1U 12.303 31/64" 43 107 60 45 14 ○

D106-03-12400A1 AP30P1U 12.4 43 107 60 45 14 ○

D106-03-12500A1 AP30P1U 12.5 43 107 60 45 14 ●

D106-03-12600A1 AP30P1U 12.6 43 107 60 45 14 ○

D106-03-12700A1 AP30P1U 12.7 1/2" 43 107 60 45 14 ○

D106-03-12750A1 AP30P1U 12.75 43 107 60 45 14 ○

D106-03-12800A1 AP30P1U 12.8 43 107 60 45 14 ○

D106-03-12900A1 AP30P1U 12.9 43 107 60 45 14 ○

D106-03-13000A1 AP30P1U 13 43 107 60 45 14 ●

D106-03-13100A1 AP30P1U 13.1 43 107 60 45 14 ○

D106-03-13200A1 AP30P1U 13.2 43 107 60 45 14 ●

D106-03-13300A1 AP30P1U 13.3 43 107 60 45 14 ○

D106-03-13400A1 AP30P1U 13.4 43 107 60 45 14 ○

D106-03-13494A1 AP30P1U 13.494 17/32" 43 107 60 45 14 ○

D106-03-13500A1 AP30P1U 13.5 43 107 60 45 14 ○

D106-03-13600A1 AP30P1U 13.6 43 107 60 45 14 ○

D106-03-13700A1 AP30P1U 13.7 43 107 60 45 14 ○

D106-03-13800A1 AP30P1U 13.8 43 107 60 45 14 ○

D106-03-13900A1 AP30P1U 13.9 43 107 60 45 14 ○

D106-03-14000A1 AP30P1U 14 43 107 60 45 14 ●

D106-03-14100A1 AP30P1U 14.1 45 115 65 48 16 ●

D106-03-14200A1 AP30P1U 14.2 45 115 65 48 16 ●

D106-03-14288A1 AP30P1U 14.288 9/16" 45 115 65 48 16 ○

D106-03-14300A1 AP30P1U 14.3 45 115 65 48 16 ○

D106-03-14400A1 AP30P1U 14.4 45 115 65 48 16 ○

D106-03-14500A1 AP30P1U 14.5 45 115 65 48 16 ●

D106-03-14600A1 AP30P1U 14.6 45 115 65 48 16 ●

D106-03-14700A1 AP30P1U 14.7 45 115 65 48 16 ●

D106-03-14750A1 AP30P1U 14.75 45 115 65 48 16 ○

D106-03-14800A1 AP30P1U 14.8 45 115 65 48 16 ○

D106-03-15000A1 AP30P1U 15 45 115 65 48 16 ●

D106-03-15100A1 AP30P1U 15.1 45 115 65 48 16 ○

D106-03-15200A1 AP30P1U 15.2 45 115 65 48 16 ○

D106-03-15300A1 AP30P1U 15.3 45 115 65 48 16 ○

D106-03-15500A1 AP30P1U 15.5 45 115 65 48 16 ●

D106-03-15600A1 AP30P1U 15.6 45 115 65 48 16 ○

D106-03-15700A1 AP30P1U 15.7 45 115 65 48 16 ●

D106-03-15800A1 AP30P1U 15.8 45 115 65 48 16 ●

D106-03-15875A1 AP30P1U 15.875 5/8" 45 115 65 48 16 ○

D106-03-15900A1 AP30P1U 15.9 45 115 65 48 16 ○

D106-03-16000A1 AP30P1U 16 45 115 65 48 16 ●

Marked：● Stock available ○ Non-stocked standard

300
Drilling

Solid Carbide Drill D106 with Internal Coolant - 5xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-03000A1 AP30P1U 3 23 66 28 36 4 ●

D106-05-03100A1 AP30P1U 3.1 23 66 28 36 4 ●

D106-05-03175A1 AP30P1U 3.175 1/8" 23 66 28 36 4 ○

D106-05-03200A1 AP30P1U 3.2 23 66 28 36 4 ●

D106-05-03250A1 AP30P1U 3.25 23 66 28 36 4 ○

D106-05-03300A1 AP30P1U 3.3 23 66 28 36 4 ●

D106-05-03400A1 AP30P1U 3.4 23 66 28 36 4 ○

D106-05-03500A1 AP30P1U 3.5 23 66 28 36 4 ●

D106-05-03572A1 AP30P1U 3.572 9/64" 23 66 28 36 4 ○

D106-05-03600A1 AP30P1U 3.6 23 66 28 36 4 ●

D106-05-03650A1 AP30P1U 3.65 23 66 28 36 4 ○

D106-05-03700A1 AP30P1U 3.7 23 66 28 36 4 ●

D106-05-03800A1 AP30P1U 3.8 29 74 36 36 4 ○

D106-05-03900A1 AP30P1U 3.9 29 74 36 36 4 ●

D106-05-03969A1 AP30P1U 3.969 5/32" 29 74 36 36 4 ○

D106-05-04000A1 AP30P1U 4 29 74 36 36 4 ●

D106-05-04100A1 AP30P1U 4.1 29 74 36 36 6 ○

D106-05-04200A1 AP30P1U 4.2 29 74 36 36 6 ●

D106-05-04300A1 AP30P1U 4.3 29 74 36 36 6 ○

Solid Carbide Drill

D106-05-04366A1 AP30P1U 4.366 11/64" 29 74 36 36 6 ○

D106-05-04400A1 AP30P1U 4.4 29 74 36 36 6 ○

D106-05-04500A1 AP30P1U 4.5 29 74 36 36 6 ●

D106-05-04600A1 AP30P1U 4.6 29 74 36 36 6 ○

D106-05-04650A1 AP30P1U 4.65 29 74 36 36 6 ○

D106-05-04700A1 AP30P1U 4.7 29 74 36 36 6 ○

D106-05-04763A1 AP30P1U 4.763 3/16" 35 82 44 36 6 ○

D106-05-04800A1 AP30P1U 4.8 35 82 44 36 6 ●

D106-05-04900A1 AP30P1U 4.9 35 82 44 36 6 ●

D106-05-05000A1 AP30P1U 5 35 82 44 36 6 ●

D106-05-05100A1 AP30P1U 5.1 35 82 44 36 6 ●

D106-05-05159A1 AP30P1U 5.159 13/64" 35 82 44 36 6 ○

D106-05-05200A1 AP30P1U 5.2 35 82 44 36 6 ●

D106-05-05300A1 AP30P1U 5.3 35 82 44 36 6 ○

D106-05-05400A1 AP30P1U 5.4 35 82 44 36 6 ○

D106-05-05500A1 AP30P1U 5.5 35 82 44 36 6 ●

D106-05-05550A1 AP30P1U 5.55 35 82 44 36 6 ○

Marked：● Stock available ○ Non-stocked standard

301
 Drilling

Solid Carbide Drill D106 with Internal Coolant - 5xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-05556A1 AP30P1U 5.556 7/32" 35 82 44 36 6 ○

D106-05-05600A1 AP30P1U 5.6 35 82 44 36 6 ○

D106-05-05700A1 AP30P1U 5.7 35 82 44 36 6 ○

D106-05-05800A1 AP30P1U 5.8 35 82 44 36 6 ●

D106-05-05900A1 AP30P1U 5.9 35 82 44 36 6 ●

D106-05-05953A1 AP30P1U 5.953 15/64" 35 82 44 36 6 ○

D106-05-06000A1 AP30P1U 6 35 82 44 36 6 ●

D106-05-06100A1 AP30P1U 6.1 43 91 53 36 8 ○

D106-05-06200A1 AP30P1U 6.2 43 91 53 36 8 ○

D106-05-06300A1 AP30P1U 6.3 43 91 53 36 8 ○

D106-05-06350A1 AP30P1U 6.35 1/4" 43 91 53 36 8 ○

D106-05-06400A1 AP30P1U 6.4 43 91 53 36 8 ○

D106-05-06500A1 AP30P1U 6.5 43 91 53 36 8 ●

D106-05-06600A1 AP30P1U 6.6 43 91 53 36 8 ○

D106-05-06700A1 AP30P1U 6.7 43 91 53 36 8 ○

D106-05-06747A1 AP30P1U 6.747 17/64" 43 91 53 36 8 ○

D106-05-06800A1 AP30P1U 6.8 43 91 53 36 8 ●

D106-05-06900A1 AP30P1U 6.9 43 91 53 36 8 ●

D106-05-07000A1 AP30P1U 7 43 91 53 36 8 ●

D106-05-07100A1 AP30P1U 7.1 43 91 53 36 8 ○

D106-05-07144A1 AP30P1U 7.144 9/32" 43 91 53 36 8 ○

D106-05-07200A1 AP30P1U 7.2 43 91 53 36 8 ○

D106-05-07300A1 AP30P1U 7.3 43 91 53 36 8 ○

D106-05-07400A1 AP30P1U 7.4 43 91 53 36 8 ●

D106-05-07500A1 AP30P1U 7.5 43 91 53 36 8 ●

D106-05-07541A1 AP30P1U 7.541 19/64" 43 91 53 36 8 ○

D106-05-07550A1 AP30P1U 7.55 43 91 53 36 8 ○

D106-05-07600A1 AP30P1U 7.6 43 91 53 36 8 ○

D106-05-07700A1 AP30P1U 7.7 43 91 53 36 8 ○

D106-05-07800A1 AP30P1U 7.8 43 91 53 36 8 ●

D106-05-07900A1 AP30P1U 7.9 43 91 53 36 8 ●

D106-05-07938A1 AP30P1U 7.938 5/16" 43 91 53 36 8 ○

D106-05-08000A1 AP30P1U 8 43 91 53 36 8 ●

D106-05-08100A1 AP30P1U 8.1 49 103 61 40 10 ○

D106-05-08200A1 AP30P1U 8.2 49 103 61 40 10 ○

D106-05-08300A1 AP30P1U 8.3 49 103 61 40 10 ○

D106-05-08334A1 AP30P1U 8.334 21/64" 49 103 61 40 10 ○

D106-05-08400A1 AP30P1U 8.4 49 103 61 40 10 ○

D106-05-08500A1 AP30P1U 8.5 49 103 61 40 10 ●

D106-05-08600A1 AP30P1U 8.6 49 103 61 40 10 ●

D106-05-08700A1 AP30P1U 8.7 49 103 61 40 10 ○

D106-05-08731A1 AP30P1U 8.731 11/32" 49 103 61 40 10 ○

D106-05-08800A1 AP30P1U 8.8 49 103 61 40 10 ●

D106-05-08900A1 AP30P1U 8.9 49 103 61 40 10 ●

Marked：● Stock available ○ Non-stocked standard

302
Drilling

Solid Carbide Drill D106 with Internal Coolant - 5xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-09000A1 AP30P1U 9 49 103 61 40 10 ●

D106-05-09100A1 AP30P1U 9.1 49 103 61 40 10 ○

D106-05-09128A1 AP30P1U 9.128 23/64" 49 103 61 40 10 ○

D106-05-09200A1 AP30P1U 9.2 49 103 61 40 10 ○

D106-05-09300A1 AP30P1U 9.3 49 103 61 40 10 ●

D106-05-09400A1 AP30P1U 9.4 49 103 61 40 10 ○

D106-05-09500A1 AP30P1U 9.5 49 103 61 40 10 ○

D106-05-09525A1 AP30P1U 9.525 3/8" 49 103 61 40 10 ○

D106-05-09550A1 AP30P1U 9.55 49 103 61 40 10 ○

D106-05-09600A1 AP30P1U 9.6 49 103 61 40 10 ○

D106-05-09700A1 AP30P1U 9.7 49 103 61 40 10 ○

D106-05-09800A1 AP30P1U 9.8 49 103 61 40 10 ●

D106-05-09900A1 AP30P1U 9.9 49 103 61 40 10 ●

D106-05-09922A1 AP30P1U 9.922 25/64" 49 103 61 40 10 ○

D106-05-10000A1 AP30P1U 10 49 103 61 40 10 ●

D106-05-10100A1 AP30P1U 10.1 56 118 71 45 12 ●

D106-05-10200A1 AP30P1U 10.2 56 118 71 45 12 ●

D106-05-10300A1 AP30P1U 10.3 56 118 71 45 12 ●

D106-05-10319A1 AP30P1U 10.319 13/32" 56 118 71 45 12 ○

Solid Carbide Drill

D106-05-10400A1 AP30P1U 10.4 56 118 71 45 12 ○

D106-05-10500A1 AP30P1U 10.5 56 118 71 45 12 ●

D106-05-10600A1 AP30P1U 10.6 56 118 71 45 12 ●

D106-05-10700A1 AP30P1U 10.7 56 118 71 45 12 ○

D106-05-10716A1 AP30P1U 10.716 27/64" 56 118 71 45 12 ○

D106-05-10800A1 AP30P1U 10.8 56 118 71 45 12 ●

D106-05-10900A1 AP30P1U 10.9 56 118 71 45 12 ○

D106-05-11000A1 AP30P1U 11 56 118 71 45 12 ●

D106-05-11100A1 AP30P1U 11.1 56 118 71 45 12 ○

D106-05-11113A1 AP30P1U 11.113 7/16" 56 118 71 45 12 ○

D106-05-11200A1 AP30P1U 11.2 56 118 71 45 12 ○

D106-05-11300A1 AP30P1U 11.3 56 118 71 45 12 ○

D106-05-11400A1 AP30P1U 11.4 56 118 71 45 12 ○

D106-05-11500A1 AP30P1U 11.5 56 118 71 45 12 ○

D106-05-11509A1 AP30P1U 11.509 29/64" 56 118 71 45 12 ○

D106-05-11550A1 AP30P1U 11.55 56 118 71 45 12 ○

D106-05-11600A1 AP30P1U 11.6 56 118 71 45 12 ○

D106-05-11700A1 AP30P1U 11.7 56 118 71 45 12 ○

D106-05-11800A1 AP30P1U 11.8 56 118 71 45 12 ●

D106-05-11900A1 AP30P1U 11.9 56 118 71 45 12 ○

D106-05-11906A1 AP30P1U 11.906 15/32" 56 118 71 45 12 ○

D106-05-12000A1 AP30P1U 12 56 118 71 45 12 ●

D106-05-12100A1 AP30P1U 12.1 60 124 77 45 14 ○

D106-05-12200A1 AP30P1U 12.2 60 124 77 45 14 ○

D106-05-12250A1 AP30P1U 12.25 60 124 77 45 14 ○

Marked：● Stock available ○ Non-stocked standard

303
 Drilling

Solid Carbide Drill D106 with Internal Coolant - 5xDc P M S K H N O

●● ● ● ●● ● ●● ●

Dc d1

Lc

L2 L5

L1

Dc(m7) Dc Lc L1 L2 L5 d1(h6)
Product code stock
mm inch/No. mm mm mm mm mm
D106-05-12300A1 AP30P1U 12.3 60 124 77 45 14 ○

D106-05-12303A1 AP30P1U 12.303 31/64" 60 124 77 45 14 ○

D106-05-12400A1 AP30P1U 12.4 60 124 77 45 14 ○

D106-05-12500A1 AP30P1U 12.5 60 124 77 45 14 ●

D106-05-12600A1 AP30P1U 12.6 60 124 77 45 14 ○

D106-05-12700A1 AP30P1U 12.7 1/2" 60 124 77 45 14 ○

D106-05-12750A1 AP30P1U 12.75 60 124 77 45 14 ○

D106-05-12800A1 AP30P1U 12.8 60 124 77 45 14 ○

D106-05-12900A1 AP30P1U 12.9 60 124 77 45 14 ○

D106-05-13000A1 AP30P1U 13 60 124 77 45 14 ●

D106-05-13100A1 AP30P1U 13.1 60 124 77 45 14 ○

D106-05-13200A1 AP30P1U 13.2 60 124 77 45 14 ●

D106-05-13300A1 AP30P1U 13.3 60 124 77 45 14 ○

D106-05-13400A1 AP30P1U 13.4 60 124 77 45 14 ○

D106-05-13494A1 AP30P1U 13.494 17/32" 60 124 77 45 14 ○

D106-05-13500A1 AP30P1U 13.5 60 124 77 45 14 ○

D106-05-13600A1 AP30P1U 13.6 60 124 77 45 14 ○

D106-05-13700A1 AP30P1U 13.7 60 124 77 45 14 ●

D106-05-13800A1 AP30P1U 13.8 60 124 77 45 14 ○

D106-05-13900A1 AP30P1U 13.9 60 124 77 45 14 ○

D106-05-14000A1 AP30P1U 14 60 124 77 45 14 ●

D106-05-14100A1 AP30P1U 14.1 63 133 83 48 16 ●

D106-05-14200A1 AP30P1U 14.2 63 133 83 48 16 ●

D106-05-14288A1 AP30P1U 14.288 9/16" 63 133 83 48 16 ○

D106-05-14300A1 AP30P1U 14.3 63 133 83 48 16 ○

D106-05-14400A1 AP30P1U 14.4 63 133 83 48 16 ○

D106-05-14500A1 AP30P1U 14.5 63 133 83 48 16 ●

D106-05-14600A1 AP30P1U 14.6 63 133 83 48 16 ●

D106-05-14700A1 AP30P1U 14.7 63 133 83 48 16 ●

D106-05-14750A1 AP30P1U 14.75 63 133 83 48 16 ○

D106-05-14800A1 AP30P1U 14.8 63 133 83 48 16 ○

D106-05-15000A1 AP30P1U 15 63 133 83 48 16 ●

D106-05-15100A1 AP30P1U 15.1 63 133 83 48 16 ○

D106-05-15200A1 AP30P1U 15.2 63 133 83 48 16 ○

D106-05-15300A1 AP30P1U 15.3 63 133 83 48 16 ○

D106-05-15500A1 AP30P1U 15.5 63 133 83 48 16 ●

D106-05-15600A1 AP30P1U 15.6 63 133 83 48 16 ○

D106-05-15700A1 AP30P1U 15.7 63 133 83 48 16 ●

D106-05-15800A1 AP30P1U 15.8 63 133 83 48 16 ●

D106-05-15875A1 AP30P1U 15.875 5/8" 63 133 83 48 16 ○

D106-05-15900A1 AP30P1U 15.9 63 133 83 48 16 ○

D106-05-16000A1 AP30P1U 16 63 133 83 48 16 ●

Marked：● Stock available ○ Non-stocked standard

304
Drilling

Cutting Data for D106 Solid Carbide Drill Family

The specified cutting data are average recommended values. For special applications, adjustment is recommended.

Drilling depth 3xDc 5xDc

Vc=Cutting speed (m/min)

Feed code = feed reference table see page 306 Product family D106 D106 D106 D106
Dia. Range(mm) 3.00-16.00 3.00-16.00 3.00-16.00 3.00-16.00

Coolant External coolant Internal coolant External coolant Internal coolant

Brinell Tensile
Workpiece material hardness strength Rm Vc Feed code Vc Feed code Vc Feed code Vc Feed code
(HB) (N/mm2)
C≤0.25% Annealed 125 428 80-100 F 90-115 F 80-100 F 90-115 F
0.25 < C≤0.55% Annealed 190 639 70-90 E 80-100 E 70-90 E 80-100 E
0.25 < C≤0.55% Heat-treated 210 708 70-90 E 80-100 E 70-90 E 80-100 E
Unalloyed steel C > 0.55% Annealed 190 639 70-90 E 80-100 E 70-90 E 80-100 E
C > 0.55% Heat-treated 300 1013 50-70 D 50-70 D 50-70 D 50-70 D
Free cutting steel
Annealed 220 745 80-100 F 90-115 F 80-100 F 90-115 F
(short-chipping)
Annealed 175 591 70-100 E 80-110 E 70-100 E 80-110 E
P
Heat-treated 300 1013 50-70 D 60-70 D 50-70 D 60-70 D
Low-alloyed steel
Heat-treated 380 1282 35-45 C 40-50 C 35-45 C 40-50 C
Heat-treated 430 1477 30-40 B 30-40 B 30-40 B 30-40 B
Annealed 200 675 55-65 D 60-80 D 55-65 D 60-80 D
High-alloyed steel and
Hardened and tempered 300 1013 40-50 C 40-60 C 40-50 C 40-60 C
high-alloyed tool steel
Hardened and tempered 400 1361 30-40 C 45-50 C 30-40 C 45-50 C
Ferritic/martensitic, annealed 200 675 50-70 D 60-80 D 50-70 D 60-80 D
Stainless steel
Martensitic, heat-treated 330 1114 40-50 C 40-50 C 40-50 C 40-50 C
Austenitic, quench hardened 200 675 40-50 C 40-50 C
Austenitic, precipitation
300 1013 35-45 C 40-50 C 35-45 C 40-50 C
M Stainless steel hardened (PH)

Austenitic/ferritic, duplex 230 778 25-35 B 25-35 B

Ferritic 200 400 70-90 G 70-90 G 70-90 G 70-90 G

Malleable cast iron
Pearlitic 260 700 60-80 G 60-80 G 60-80 G 60-80 G
Low tensile strength 180 200 80-100 H 80-110 H 80-100 H 80-110 H

Solid Carbide Drill

Grey cast iron
K High tensile strength/austenitic 245 350 70-90 G 70-90 G 70-90 G 70-90 G

Cast iron with Ferritic 155 400 80-100 G 80-110 H 80-100 G 80-110 H
spheroidal graphite Pearlitic 265 700 60-80 F 60-80 F 60-80 F 60-80 F
GGV(CGI) 230 400 60-80 F 60-80 F 60-80 F 60-80 F

Wrought aluminium non-aging 30 - 200-300 G 300-400 G 200-300 G 300-400 G

alloys aged 100 340 200-300 G 300-400 G 200-300 G 300-400 G
≤ 12% Si, non-aging 75 260 160-220 H 180-240 H 160-220 H 180-240 H

Cast aluminium alloys ≤ 12% Si, aged 90 310 160-200 H 180-200 H 160-200 H 180-200 H

N > 12% Si, non-aging 130 450 130-160 G 140-180 G 130-160 G 140-180 G
Magnesium alloys 70 250
Unalloyed, electrolytic copper 100 340 120-160 C 140-170 D 120-160 C 140-170 D
Copper and copper Brass, bronze, red brass 90 310 110-140 E 120-140 E 110-140 E 120-140 E
alloys
(bronze/brass) Cu alloys, short-chip 110 380 120-150 F 140-180 F 120-150 F 140-180 F
High tensile, Ampco alloy 300 1010 45-60 B 45-60 B 45-60 B 45-60 B
Annealed 200 680 30-40 B 30-40 B
Fe-based
Hardened 280 940 20-25 A 20-25 A

Heat-resistant alloys Annealed 250 840 20-30 B 20-30 B

Ni or Co based Hardened 350 1180 10-15 A 10-15 A

Cast 320 1080 15-25 A 15-25 A

S
Pure titanium 200 680 30-40 B 40-50 C 30-40 B 40-50 C

Titanium alloys α and β alloys, hardened 375 1260 20-30 A 25-35 B 20-30 A 25-35 B

β alloys 410 1400 10-15 A 10-15 A

Tungsten alloys 1177 300 1010
Molybdenum alloys 1262 300 1010
Hardened and tempered 50HRC - 20-35 A 20-35 A 20-35 A 20-35 A
Hardened steel Hardened and tempered 55HRC -
H
Hardened and tempered 60HRC -
Hardened cast iron Hardened and tempered 50HRC -

305
 Drilling

Feed Reference Table

Feed rate f（mm/rev）

A B C D E F G H
3.0 0.03 0.04 0.05 0.06 0.08 0.10 0.12 0.14
4.0 0.04 0.05 0.06 0.08 0.10 0.12 0.14 0.16
5.0 0.05 0.06 0.07 0.09 0.10 0.12 0.16 0.18
6.0 0.05 0.07 0.08 0.10 0.12 0.15 0.18 0.20
Dia.
8.0 0.06 0.08 0.10 0.12 0.15 0.18 0.20 0.23
mm
10.0 0.08 0.10 0.12 0.14 0.18 0.20 0.24 0.28
12.0 0.10 0.12 0.14 0.18 0.20 0.24 0.28 0.32
14.0 0.10 0.14 0.18 0.20 0.24 0.28 0.32 0.34
16.0 0.12 0.15 0.18 0.20 0.25 0.30 0.34 0.36
20.0 0.15 0.16 0.20 0.25 0.30 0.34 0.37 0.40

306
Drilling

Thread Pilot Hole Diameters-Tapping

M Metric coarse pitch thread

DIN 13 and DIN ISO 965-1 MF Metric fine pitch thread
DIN 13 and DIN ISO 965-1

D D1
D D1
Max(mm)
Diameter Min (mm) Diameter
5H/6H Max mm
Diameter*P Diameter
M4 3.242 3.422 3.30 5H/6H
M4.5 3.688 3.878 3.70 M3.5x0.35 3.221 3.15
M5 4.134 4.334 4.20 M4x0.35 3.721 3.65
M6 4.917 5.153 5.00 M4x0.5 3.599 3.50
M7 5.917 6.153 6.00 M4.5x0.5 4.099 4.00
M8 6.647 6.912 6.80 M5x0.35 4.721 4.65
M9 7.647 7.912 7.80 M5x0.5 4.599 4.50
M10 8.376 8.676 8.50 M5x0.75 4.378 4.20
M11 9.376 9.676 9.50 M5x0.5 5.599 5.50
M12 10.106 10.441 10.20 M6x0.75 5.378 5.25
M14 11.835 12.210 12.00 M7x0.5 6.599 6.50
M16 13.835 14.210 14.00 M7x0.75 6.378 6.25
M18 15.294 15.744 15.50 M8x0.5 7.599 7.50
M20 17.294 17.744 17.50 M8x0.75 7.378 7.25
M22 19.294 19.744 19.50 M8x1 7.153 7.00
M9x0.75 8.378 8.25

UNC Coarse thread M9x1 8.153 8.00

ASME B1.1 standard M10x0.5 9.599 9.50
M10x0.75 9.378 9.25
D D1 M10x1 9.153 9.00
M10x1.25 8.912 8.75
Diameter Min (mm) Max(mm) M11x1 10.153 10.00
Diameter
P Gg/1" 2B/3B 2B M12x0.5 11.599 11.50
8-32 UNC 3.302 3.531 3.50 M12x1 11.153 11.00
10-24 UNC 3.683 3.962 3.90 M12x1.25 10.912 10.75
12-24 UNC 4.343 4.597 4.50

Solid Carbide Drill

M12x1.5 10.676 10.50
1/4-20 UNC 4.976 5.268 5.10 M13x1 12.153 12.00
5/16-18 UNC 6.411 6.734 6.60 M14x0.75 13.378 13.20
3/8-16 UNC 7.805 8.164 8.00 M14x1 13.153 13.00
7/16-14 UNC 9.149 9.550 9.40 M14x1.25 12.912 12.75
1/2-13 UNC 10.584 11.013 10.28 M14x1.5 12.676 12.50
9/16-12 UNC 11.996 12.456 12.20 M15x1 14.153 14.00
5/8-11 UNC 13.376 13.868 13.50 M15x1.5 13.676 13.50
3/4-10 UNC 16.299 16.833 16.50 M16x0.75 15.378 15.20
7/8-9 UNC 19.169 19.748 19.50 M16x1 15.153 15.00
M16x1.25 14.912 14.80

UNF Fine thread

ASME B1.1 standard
M16x1.5
M17x1
14.676
16.153
14.50
16.00
M18x1 17.153 17.00
D D1
M18x1.5 16.676 16.50
Diameter Min (mm) M18x2 16.21 16.00
Max(mm)2B Diameter M20x1 19.153 19.00
P Gg/1" 2B/3B
8-36 UNF 3.404 3.607 3.50 M20x1.5 18.676 18.50
10-32 UNF 3.962 4.166 4.10 M20x2 18.21 18.00
12-28 UNF 4.496 4.724 4.60
1/4-28 UNF 5.367 5.580 5.50
5/16-24 UNF 6.792 7.038 6.90
3/8-24 UNF 8.379 8.626 8.50
7/16-20 UNF 9.738 10.030 9.90
1/2-20 UNF 11.326 11.618 11.50
9/16-18 UNF 12.761 13.084 12.90
5/8-18 UNF 14.348 14.671 14.50
3/4-16 UNF 17.330 17.689 17.50

307
 Drilling

Thread Pilot Hole Diameters- Forming

M Metric coarse pitch thread

DIN 13 and DIN ISO 965-1 MF Metric fine pitch thread
DIN 13 and DIN ISO 965-1

D D

Diameter Diameter Diameter Diameter

M3.5 3.25 M4x0.5 3.80
M4 3.70 M5x0.5 4.80
M5 4.65 M6x0.5 5.80
M6 5.55 M6x0.75 5.65
M8 7.40 M7x0.75 6.65
M10 9.30 M8x0.75 7.65
M12 11.20 M8x1 7.55
M14 13.10 M10x0.75 9.65
M16 15.10 M10x1 9.55
M18 16.90 M10x1.25 9.40
M20 18.90 M12x1 11.55
M12x1.25 11.40
M12x1.5 11.30
M14x1 13.55
M14x1.5 13.30
M16x1 15.55
M16x1.5 15.30
M18x1 17.55
M18x1.5 17.30
M20x1.5 19.30
M20x2 19.10
M22x1.5 21.30

UNC Coarse thread

ASME B1.1 standard UNF Fine thread
ASME B1.1 standard

D D

Diameter Diameter Diameter Diameter

6-32 UNC 3.15 6-40 UNF 3.20
8-32 UNC 3.80 8-36 UNF 3.85
10-24 UNC 4.30 10-32 UNF 4.45
12-24 UNC 5.00 12-28 UNF 5.05
1/4-20 UNC 5.75 1/4-28 UNF 5.90
5/16-18 UNC 7.25 5/16-24 UNF 7.45
3/8-16 UNC 8.75 3/8-24 UNF 9.00
7/16-14 UNC 10.30 7/16-20 UNF 10.50
1/2-13 UNC 11.80 1/2-20 UNF 12.10
9/16-12 UNC 13.30 9/16-18 UNF 13.70
5/8-11 UNC 14.80 5/8-18 UNF 15.25
3/4-10 UNC 17.90 3/4-16 UNF 18.40

308
 Technical information

Grade Conversion Table

Turning

COROMANT

ISCAR

KENNAMETAL

TAEGUTEC

TUNGALOY

ZCC
ACHTECK

KORLOY

KYOCERA

MITSUBISHI

SECO

SUMITOMO

WALTER
classification

classification
Material
ISO

GC4315 KCP10 NC3010 CA515 MC6015 TP1500 AC810P T9115 WPP10S YBC152
P10 AC150P IC8150 TT8115
GC4215 KC9110 NC3015 CA5515 UE6110 TP1501 AC700G T9015 WPP10 YBC151

GC4325 KCP25 NC3220 CA525 MC6025 TP2500 AC8025P T9125 WPP20S YBC251
P P20 AC250P
GC4225
IC8250
KC9215 NC3120 CA5525 UE6020 TP2501 AC820P
TT8125
T9025 WPP20 YBC252

KCP30
GC4335 NC3030 MC6035 TT8135 T9135 WPP30S YBC351
P30 AC350P IC8350 KCP40 CA5535 TP3500 AC830P
GC4235 NC500H UE6035 TT8020* T9035 WPP30 YBC352
KC9040

CA6515 MC7015
KCM15 TS2000* AC610M AH110* YBM151
GC2015 IC907* PR1305* US7020 TT9215 WSM10*
M10 AP100S* KC5510* PC8110* TH1000* AC6020M AH905* YBG102*
GC1105* IC807* PR1310* VP10RT* TT5080* WSM10S*
KCU10* CP200* AC510U* AH8005* YBG105*
PR1215* MP9005*
M CA6525 T6120
YBM251
GC2025 KCM25 PR930* MC7025 AC620M T6020 WSM20*
IC908* NC9025 TM2000 TT9225 YBG202*
M20 AP301M* GC1115* KC5525* PR1025* VP15TF* AC6030M AH120* WSM20S*
IC887* PC5300* CP500* TT9080* YBG212*
GC15* KCU25* RP1225* MP9015* AC520U* AH630* WMP20S
YBG205*
PR1325* AH8015*

GC3205 CA4505 MC5005 TK1001 AC405K WKK10S

K10 AC100K IC5005 KCK05 NC6205 TT7005 T505 YBD052
GC3005 CA4010 UC5105 TK1000 AC410K WAK10

K
AC150K GC3210 KCK15 CA4515 MC5015 TK2001 AC415K TT7310 T5115 WKK20S YBD152C
K20 IC5010 NC6110
ACK15A GC3215 KC9315 CA415 UC5115 TK2000 AC700G TT7015 T515 WAK20 YBD152

GCS05F KCU10* TH1000* AH110*

IC807* PR1305* VP10RT* YBG102*
S10 AP100S* GC1105* KC5510* PC8110* TH1500* AC510U* TT5080* AH905* WSM10*
IC907* PR1310* MP9005* YBG105*
GC1115* KC5010 TS2000* AH8005*
S
KCU20* PR1025* YBG212*
GC15* IC808* VP15TF* AH120*
S20 AP301M* KC5525* PC5300* PR1225* CP500* AC520U* TT9080* WSM20* YBG202*
GC1115* IC908* MP9015* AH8015*
KC5025* PR1325* YBG205*

K68
N N10 AW100K H10 IC20
K313
H01 KW10 HTI10 KX H1 K10 TH10 WK1 YD101

“*”PVD coating grades

326
Technical information

Turning Chip Breaker Conversion Table

Negative turning insert

COROMANT

ISCAR
ACHTECK

DURACARB

KENNAMETAL

TAEGUTEC
KORLOY

KYOCERA

MITSUBISHI

SECO

SUMITOMO

TUNGALOY

VALENITE

WALTER

ZCC
classification

Application
ISO

DP, GP, PP FA FA, FS TF, 01

SF FF, FS HU, VL FH FF1, FF2 F2 FP5 SF
VF FL FX ZF
Finishing

PB1 FP XF LP NS, 11
VG, VF
QF NF, F3P LF, FN XP SH MF2 SU FG TS, AS NF4 NF
VQ
41 HQ FY SE FM TSF DF
finishing

VB, VC,
CQ, PQ
Semi-

PB3 PF, XF 43 HC SA LU FC, FT NS6 NM

CJ

VF, DNUX
PL5 K ES UX GX, HM FS
S

52 MN HC GS MR3 MC ASW MP3 PM

QM, 23, LC PP MS, MP HA XQ, XS MJ, SY MF4, MF5 UP, GX, AG ML P NMS,
SM, -NGP, UP, P,
23
TF 42 -NGP
VP3 A3, AH MS M5, MR3, EG, EX, UP MP HMM, M2 NMT
machining

SR, SMR RP VM MS, MU GJ MR4 MU SA NRS, NRT

Medium

PM, XM M3P VM PG MP, MV MF3 GE MP5

45 P PC TM M2 PM
PC3 QM VL HS, GS PS MA MF5, M3 GU NM4
P
MP HS NM6
PD3 HM, XMR GN 46 HM, GM UX, UG MT M3 DM
RP, RM CS NM9
MG- 33, 37,
M4
PC4 MG- 53 UN B25 C MG- UZ MG- 38 MG- MG-
MR4
DM, MG-
machining
Roughing

PT, GT MH M5 ME
PD5 PR NR, R3P RN HR, GR RT TH R3 NR4, RP5 DR
PH, HT GH, RP MR7, M6 MU, MX

PD8 PR RM PX RX NRF
Finishing Heavy machining

R6, RR9 MP
QR R3P TRS
MR, RP GH HX HZ R4, R5, 37 HG RH R6 NR6
MR NM 57
RR6 HP
HCS R8, 56, 57 HF 65 ER
PC9 HR, 31 RH VT HT, HD NRR
HX, HBS R7 HU TU HDR
PD9 VH HV, HDS, HXD HW HY, HZ

MB2 MF SF, F3M 41 FP HA, VP2 MQ, GU FS, LM MF1 SU EA, SF SF F5 NF4 EF
machining machining machining machining
Roughing Medium Roughing Medium

MC3 MM M3M 42 MP, UP GS, HS MS, MU MS, GM, MA MF4 EX, UP, GU EM SS, S NM4 EM
M

NR4
MC4 MR R3M 45 RP VM HU RM MR6, MF5 MU, HM ET SM M5 ER
NRS
Technical guide

NM5,
PC4 MG- 53 RP C MG-, GK M5 MG- MG- MG-
RK5

K
KC4 KT
KR UN GR ZS, GC GX, RK MR7 GZ CH RK7 DR
KD5 RT
Finishing

MB2 SF SF FS VP1 MQ FJ MF1 EF EA, SF F5 NF4 NF

M1 NFT
machining machining

SGF MS VP2 MJ SU ML
Roughing Medium

SM, -NGP, PP UP, P, MF4, MF5 HMM, NMS,

S SC3 42 VP3 MS, MU MS EG, EX, UP MP, SU, M2 NM
23 TF -NGP M5, MR3, SA NMT
SR, SMR RP VM GJ MU MK
MR4 NRS, NRT

NR4
MC4 MR R3M 45 RP VM HU RM MR6,MF5 MU,HM ET SM M5 ER
NRS

327
 Technical information

Turning Chip Breaker Conversion Table

Positive turning insert

COROMANT

MITSUBISHI
ACHTECK

DURACARB

ISCAR

KENNAMETAL

TAEGUTEC
KORLOY

KYOCERA

SECO

SUMITOMO

TUNGALOY

VALENITE

WALTER

ZCC
classification

Application
ISO

XP
UF, 11, VL, VF, LU FA 01, PF, PF4, SF
PF, UF 38, PF GK, GP, DP FV FF1
GM HFP FP FX PSF PF5 HF
VF
Finishing

CF, GF
PB1
GQ SMG FC SA JS
PC2
CK

VF FK
P UM
51
SM FP
HMP,
XQ
SQ, SV F1 SU FG
PM3
PS5 HM
XF 16, GT- LF GX PM4
M C05 SC, SK

K
finishing

PC PSS EF
Semi-

PC2 PM 41 MP HQ
FM PS EM
machining

XM MQ, MV PM5
Medium

14, 17
KC2 PR, UR 52 MF C25 MT- MT- F2 SF, MU MT PM PM5 E47, HR
19, MT-
XR G MT-
Semi-finishing

N NC2 AL AU AF, AS HP AK, AR AH AZ AL AW, AG FL AL IL PM2 LH

328
Technical information

Turning Machining Formula

● Cutting speed ● Cutting force

ΦDc n

Fc = Kc * ap * f (N)

Fc:Cutting force(N) Kc:Unit cutting force(N/mm²)

ap:Axial depth of cut (mm) f:Feed rate(mm/rev)

π * Dc * n
Vc = (m/min)
1000 ● Cutting power
Vc:Cutting speed(m/min) π: ≈3.14
Dc:Workpiece diameter(mm) n:Spindle speed(rev/min) Kc * Vc * ap * f
Pmot = (KW)
60000 * η
Pmot:Cutting power(KW) Kc:Unit cutting force(N/mm²)
Vc:Cutting speed(m/min) ap:Axial depth of cut (mm)
● Feed speed
f:Feed rate(mm/rev) η:Mechanical efficiency

● Chip removal
Vf = f * n (mm/min)

Vf:Cutting speed(mm/min) f:Feed rate(mm/rev)

Q = ap * f * Vc (cm3/min)
n:Spindle speed(rev/min)

Q:Chip removal(cm³/min) ap:Axial depth of cut (mm)

f:Feed rate(mm/rev) Vc:Cutting speed(m/min)
● Chip thickness

h = f * sinkr (mm) ● Theoretic surface roughness

Rmax
h:Chip thickness(mm) f:Feed rate(mm/rev) f

f2
● Chip width Rmax = * 1000 (um)
8*r
Rmax:Theoretic surface roughness (um)
ap
b= (m/min) f:Feed rate(mm/rev) r:Corner radius (mm)
sinkr
b:Chip width(mm) ap:Axial depth of cut (mm)

● Work time L
Technical guide

● Chip area

L
A = h * b = ap * f (mm2) Tc = (min)
f*n
A:Chip area(mm2) ap:Axial depth of cut (mm) Tc:Work time f:Feed rate(mm/rev)
f:Feed rate(mm/rev) n:Spindle speed(rev/min) L: Working length(mm)

329
 Technical information

Turning Insert Normal Failtures & Solutions

Failtures Pic. Analysis Solution

●
Tool materials too soft ●
Choosing high
●
Excessive cutting speed wear-resistance insert grade
Flank wear ●
Less clearance angle ●
Reduce cutting speed
●
Less feed rate ●
Enlarge clearance angle
●
Insufficient cooling ●
Increase feed rate

●
Choosing high
●
Tool materials too soft wear-resistance insert grade
Crater wear ●
Excessive cutting speed ●
Reduce cutting speed
●
Excessive feed rate ●
Reduce feed rate
●
Increasing the flow of coolant

●
Choosing tougher grade
●
Tool materials too hard
Chipping ●
Enhancing cutting
●
Less cutting strength
edge strength

●
Choosing high
wear-resistance insert grade
●
Tool materials too soft ●
Reduce cutting speed
●
Over stronge cutting edge
reduce cutting depth &
Deformation ●
Excessive cutting depth
feed rate
& feed rate ●
Choosing good thermal
●
Insufficient cooling
conductivity grade
●
Increasing the flow of coolant

●
Increase cutting rate
●
Less cutting speed ●
Choosing sharp geometry
●
Cutting edge not sharp
Built-up edge ●
Choosing less adhesion
●
Unsuitable grade
grade
●
Insufficient cooling ●
Increasing the flow of coolant

●
Choosing tougher grade
●
Enlarge lead angle
●
Excessive feed rate and ●
Choosing bigger corner
Mechanical wear cutting depth
radius
●
Vibration ●
Change to strong rigidity
holder

●
Choosing dry cutting or
●
Excessive cutting heat
Thermal cracking adequate cooling
change of edges ●
Choosing tougher grade

●
Choosing high wear-
●
Excessive feed rate & cutting resistance tool grade
Peripheral wear speed ●
Enlarge rake angle leads to
●
Tool materials too soft sharp edge
●
Reduce cutting speed

●
Enlarge rake angle leads to
●
Sticky chip on the cutting
sharp edge
edge
Coating peeling ●
Use chip breaker with bigger
●
Chip evacuation failure
space

330
Technical information

Milling Grades Conversion Table

COROMANT

ISCAR

KENNAMETAL

TAEGUTEC
ACHTECK

KORLOY

KYOCERA

MITSUBISHI

SECO

TUNGALOY

WALTER
SUMITOMO
classification
ISO

PC3600
PR630 MP1500 WKP25
AP301U GC4220 KC522M PC3500 TT7080 T3130
IC950 PR660 VP15TF MP2500 WAM10
AC301P GC4230 KC635M PC3535 TT7030 AH330
PR730 T250M WAM20
PC3525

AH120
KC522M PC5300
GC1030 IC808 PR9925 VP15TF F30M TT9080 AH725
P AP351U KC635M NC5330 ACP2000 WAM30
GC4240 IC908 PR830 VP20RT MP3000 TT9030 AH730
KC725M PC9530
GH330

IC830 VP30RT TT8020 AH140 WKP235

KC735M F40M ACP300
AP401U GC1040 IC330 PC3545 FH7020X TT7800 T3130 WXP45
KC935M MP2500 ACZ350
IC928 F7030 TT8080 AH130 WSP45

PR730
PC5300 T3130
GC1030 IC808 PR830 MP2500 TT9300 WAM30
AP301U KC635M NC5330 VP15TF ACP2000 AH725
GC2030 IC908 PR925 F30M TT9080 WXM35
PC9530 AH120
PR1025
M S
IC830 VP30RT F40M ACP300 AH130 WXM35
GC2040 PC3545 PR1225 TT8020
AP351U IC330 KC7725M MP9030 MM4500 EH20Z AH140 WSM35
S40T PC5300 PR905 TT8080
IC928 F7030 MS2500 EH520Z SH730 WSP45

PC6510 PR905 MC5020 MK2050 ACK2000 T1115

AC301K GC3220 IC810 KCK15 WKP25
K PC215K PR510 VP15TF MK2000 ACK3000 TT6080 AH120
AP351K GC4220 IC910 KC520M WKP35
PC5300 PR610 MP8010 MK3000 ACZ310 GH110

Technical guide

331
 Technical information

High Feed Cutter AHM15-XD Application Information

Face milling Maximum milling depth ap(mm)

XD..0904 XD..1205
ap.max
1.5 2.5

Ramping Maximum bevel

XD..0904 XD..1205
Da
(mm) Maximum bevel Maximum bevel Maximum bevel Maximum bevel
A B A B
25 2.80° 6.30° - -

32 1.50° 5.00° - -

40 0.80° 2.70° - -

52 - - 0.8° 2.7°

63 - - 0.6° 1.8°

66 - - 0.45° 1.8°

100 - - 0.32° 1.45°

125 - - 0.24° 1.06°

A=Maximum bevel angle of full flat contact B= Maximum bevel of full contact + radius

Plunging Maximum milling depth ar（mm)

Da(mm) XD..0904 XD..1205

Maximum bevel
25 6.0
A
32 6.0 -

40 6.0 -

50 6.0 -

52 - 9.0

63 - 9.0

66 - 9.0

80 - 9.0

100 9.0

25 - 9.0

332
Technical information

Circular Interpolation Milling Diameter range of hole that can be milled in one pass (mm)

XD..0904 XD..1205
Da
(mm) Do min Do max Do min Do max
(mm) (mm) (mm) (mm)
25 30 50 - -

32 51 64 - -

40 67 80 - -

50 87 100 - -

52 - - 87.2 104

63 - - 109.2 126

66 - - 115.2 132

80 - - 143.2 160

100 - - 183.2 200

25 - - 233.2 250

Programming Information

Circular Interpolation Milling

Indexable
R r rt k kr x
insert
XD..090408 17 0.8 2.0 6.5 1.9 1.47

XD..120508 22.8 0.8 2.5 8.4 2.4 1.00

XD..120512 20 1.2 3.0 8.3 2.8 0.86

XD..120520 20 2.0 3.0 8.0 3.4 0.90

When programmed with the theoretical tool radius "rt", the maximum deviation shown
above is produced with the final contour.
Minor deviations that occur only in rounded corners can be corrected by other tools in
subsequent process.
Technical guide

333
 Technical information

High Feed Cutter AHM20-LN06 Application Information

Straight Ramping Circular interpolate milling

Max.ap(mm)

Max.pitch
Max.ramp A

L D

Straight ramp down Circular interpolate milling

Cutter Dia(D)
Max.ramp-A Max.ap(mm) Min.length-L(mm) Min.Dia.(mm) Max.Dia(mm)

φ16 2.9° 0.7 13.8 23 32

φ17 2.6° 0.7 15.4 25 34

φ20 1.9° 1.0 30.1 31 40

φ21 1.8° 1.0 31.8 33 42

φ25 1.3° 1.0 44.0 41 50

φ26 1.3° 1.0 44.0 43 52

φ32 0.9° 1.0 63.6 55 64

φ33 0.9° 1.0 63.6 57 66

φ40 0.7° 1.0 81.8 71 80

φ50 0.5° 1.0 114.5 91 100

φ63 0.4° 1.0 143.2 117 126

NC Program Radius

Over Cut T2

Technical information for NC program

Program R Un-Cut T1 Over-Cut T2

R1.5 0.43 0

R2.0 0.29 0.06

R2.5 0.15 0.24

Program R Note: select R1.5 as program R , without over-cut.

Un-Cut T1
3.2

334
Technical information

Ramping Milling Parameters

Ramping Maximum angle A（°）

Indexable inserts diameter d（mm）

Da(mm)
d8 d10 d12 d16 d20

25 3.2 6.5 - - -

32 - 3.0 4.2 - -

40 - 1.4 3.0 - -
Max.ramp
A 50 - 2.0 2.1 - -
ap max
63 - - 1.5 2.6 -

Da 80 - - 1.4 1.4 -

100 - - - 1.0 1.3

125 - - - - 0.9

160 - - - - 0.7

ap max(mm) 6.6 8.8 10.7 14 17.2

Circular Interpolate Milling Parameters

Actual circular interpolate milling data on

Diameter range of the hole that can be milled by one pass（mm)
workpiece
Indexable inserts diameter d（mm）

Da(mm) d8 d10 d12 d16 d20

DO min DO max DO min DO max DO min DO max DO min DO max DO min DO max
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)

25 36.5 50 32 50 - - - - - -

32 - - 46 64 42.5 64 - - - -

40 - - 62 80 59 80 - - - -
pitch

Da
D0 50 - - 82 100 78.5 100 97.5 126 - -
Technical guide

63 - - - - 104.5 126 131.5 160 - -

80 - - - - 138 160 171.5 200 - -

100 - - - - - - - - 165.5 200

125 - - - - - - - - 215.5 250

160 - - - - - 10.7 - - 285.5 320

335
 Technical information

Milling General Formula

● Cutting speed ● Power demand

π * Dc * n ap * ae * Vf * Kc
Vc = (m/min) Pmot = (KW)
1000 6 * 107 * η
Vc:Cutting speed(m/min) π: ≈3.14 Pmot:Cutting power(KW) ap:Cutting depth ae:Cutting width
Dc:Cutter diameter(mm) n:Spindle speed(rev/min) Kc:Unit cutting force(N/mm²) η:Machine efficiency coefficient(0.7-0.95)

● Spindle speed ● Average chip thickness

1000 * Vc 114.7 * fz * sink * (ae/Dc)

n= (rev/min) hm = (mm)
π * Dc ψs
Vc:Cutting speed(m/min) π: ≈3.14 hm:Average chip thickness fz:Feed per tooth(mm/z)

Dc:Cutter diameter(mm) n:Spindle speed(rev/min) ae:Cutting width Dc:Cutter diameter(mm) ψs:Pressure angle

● Feed speed ● Feed force

Vf = fz * n * Z (mm/min) Cutter in the center site

ψs = 2 * arcsin (
ae
Vf:Feed speed(mm/min) fz:Feed per tooth(mm/z) ) [° ]
n:Spindle speed(rev/min) Z:Number of teeth Dc

Cutter in excentric site

● Feed rate per rev.

ae-(Dc/2)
Vf ψs = 90°+arcsin [° ]
fz = (mm/z) (Dc/2)
n*Z
fz:Feed rate per rev.(mm/z) Vf:Feed speed(mm/min)
n:Spindle speed(rev/min) Z:Number of teeth ψs:Pressure angle ae:Cutting width
Dc:Cutter diameter(mm)

● Feed rate per rev.

● Chip removal
Vf
f= (mm/rev)
n
ap * ae * Vf
f:Feed rate per rev.(mm/rev) Vf:Feed speed(mm/min) Q= (cm3/min)
n:Spindle speed(rev/min) 1000
Q:Chip removal(cm³/min) ap:Cutting depth

● Time of cut ae:Cutting width Vf:Feed speed(mm/min)

L
Tc = (min)
Vf
Tc:Time of cut(min) L:Length of feed(mm)
Vf:Feed speed(mm/min)

● Horse power n

Pmot
Hp = ap f
0.75
Hp:Horse power Pmot:Cutting power(KW)

336
Technical information

Drilling General Recommendation

● Cutting speed ● Horse power

π * Dc * n Pmot
Vc = (m/min) Hp =
1000 0.75
Vc:Cutting speed(m/min) π:≈3.14
Hp:Horsepowe Pmot:Cutting power(KW)
Dc:Drill diameter(mm) n:Spindle speed(rev/min)

● Spindle speed

● Power demand
1000 * Vc
n= (rev/min) ΦDc
π * Dc
Vc:Cutting speed(m/min) π: ≈3.14 Q * Kc
Pmot = (KW)
Dc:Drill diameter(mm) n:Spindle speed(rev/min) 60000 * η

Pmot:Cutting power(KW) Q:Chip removal(cm³/min)

● Feed speed Kc:Unit cutting force(N/mm²)
η:Machine efficiency coefficient (0.7-0.95)

Vf = fz * n * Z (mm/min)
● Torque
Vf:Feed speed(mm/min) fz:Feed per tooth(mm/z)
n:Spindle speed(rev/min) Z:Number of teeth

Dc2 * Kc * f
Mc = (N*m)
8000
● Feed rate per rev. Mc:Torque Dc:Drill diameter(mm)
Kc:Unit cutting force(N/mm²) f:Feed rate per rev.(mm/rev)

Vf
fz = (mm/z)
n*Z
fz:Feed per tooth(mm/z) Vf:Feed speed(mm/min)
n:Spindle speed(rev/min) Z:Number of teeth
● Feed force

● Feed rate per rev. f * Dc * Kc

f

Ff = 0.63 * (N)
2
Vf Ff:Feed force f:Feed rate per rev.(mm/rev)
f= (mm/rev) Dc:Drill diameter(mm) Kc:Unit cutting force(N/mm²)
n
Technical guide

f:Feed rate per rev.(mm/rev) Vf:Feed

speed(mm/min)n:Spindle speed(rev/min)

● Cutting thickness
● Chip removal

Vf * π * Dc2
Q= (cm3/min) h = fz * sink (mm)
4 * 1000
Q:Chip removal(cm³/min) Vf:Feed speed(mm/min) h:Cutting thickness(mm) fz:Feed rate(mm/rev)
π:≈3.14 Dc:Drill diameter(mm)

337
 Technical parameter

Hardness Conversion Table

Brinell Hardness 10
ball load Rockwell Hardness
3000Kg Micro Tensile
Vickers Shore's Strength
Hardness Hardness (approximate)
A scale 60kgf C scale 150kgf D scale 100kgf kgf/mm
Master WC ball HV B scale 100kgf
diamond brale diamond brale diamond brale
ball HB 1/16in ball HRB
HRA HRC HRD
- - 1865 92.0 - 80 - - -
- - 1787 91.5 - 79 - - -

- - 1710 91.0 - 78 - - -
- - 1633 90.5 - 77 - - -
- - 1556 90.0 - 76 - - -
- - 1478 89.5 - 75 - - -
- - 1400 89.0 - 74 - - -

- - 1323 88.5 - 73 - - -
- - 1245 88.0 - 72 - - -
- - 1160 87.0 - 71 - - -
- - 1076 86.5 - 70 - - -
- - 1004 86.0 - 69 - - -
- - 940 85.6 - 68.0 76.9 97 -
- - 920 85.3 - 67.5 76.5 96 -
- - 900 85.0 - 67.0 76.1 95 -
- 767 880 84.7 - 66.4 75.7 93 -
- 757 860 84.4 - 65.9 75.3 92 -

- 745 840 84.1 - 65.3 74.8 91 -

- 733 820 83.8 - 64.7 74.3 90 -
- 722 800 93.4 - 64.0 73.8 88 -
- 712 - - - - - - -
- 710 780 83.0 - 63.3 73.3 87 -
- 698 760 82.6 - 62.5 72.6 86 -

- 684 740 82.2 - 61.8 72.1 - -

- 682 737 82.2 - 61.7 72.0 84 -
- 670 720 81.8 - 61.0 71.5 83 -
- 656 700 81.3 - 60.1 70.8 - -
- 653 697 81.2 - 60.0 70.7 81 -

- 647 690 81.1 - 59.7 70.5 - -

- 638 680 80.8 - 59.2 70.1 80 -
- 630 670 80.6 - 58.8 69.8 - -
- 627 667 80.5 - 58.7 69.7 79 -

- 601 640 79.8 - 57.3 68.7 77 -

- 578 615 79.1 - 56.0 67.7 75 -
- 555 591 78.4 - 54.7 66.7 73 210
- 534 569 77.8 - 53.5 65.8 71 202

- 514 547 76.9 - 52.1 64.7 70 193

495 528 76.3 51.0 63.8 68 186
- 477 508 75.6 - 49.6 62.7 66 177
- 461 491 74.9 - 48.5 61.7 65 170
- 444 472 74.2 - 47.1 60.8 63 162

429 429 455 73.4 - 45.7 59.7 61 154

415 415 440 72.8 - 44.5 58.8 59 149
401 401 425 72.0 - 43.1 57.8 58 142
388 388 410 71.4 - 41.8 56.8 56 136
375 375 396 70.6 - 40.4 55.7 54 129

363 363 383 70.0 - 39.1 54.6 52 124

352 352 372 69.3 (110.0) 37.9 53.8 51 120
341 341 360 68.7 (109.0) 36.6 52.8 50 115
331 331 350 68.1 (108.5) 36.6 51.9 48 112
321 321 339 67.5 (108.0) 34.3 51.0 47 108

311 311 328 66.9 (107.5) 33.1 50.0 46 105

302 302 319 66.3 (107.0) 32.1 49.3 45 103
293 293 309 65.7 (106.0) 30.9 48.3 43 99
285 285 301 65.3 (105.5) 29.9 47.6 - 97
277 277 292 64.6 (104.5) 28.8 46.7 41 94

338
Technical parameter

Hardness Conversion Table

Brinell Hardness 10
ball load Rockwell Hardness
3000Kg Micro Tensile
Vickers Shore's Strength
Hardness Hardness (approximate)
A scale 60kgf C scale 150kgf D scale 100kgf kgf/mm
Master WC ball HV B scale 100kgf
diamond brale diamond brale diamond brale
ball HB 1/16in ball HRB
HRA HRC HRD
269 269 284 64.1 (104.0) 28 45.9 40 91
262 262 276 63.6 (103.0) 27 45.0 39 89
255 255 269 63.0 (102.0) 25 44.2 38 86
248 248 261 62.5 (101.0) 24 43.2 37 84
241 241 253 61.8 100 23 42.0 36 82

235 235 247 61.4 99 22 41.4 35 80

229 229 241 60.8 98.2 21 40.5 34 78
223 223 234 - 97.3 (18.8) - -
217 217 228 - 96.4 (17.5) - 33 74
212 212 222 - 95.5 (16.0) - - 72

207 207 218 - 94.6 (15.2) - 32 70

201 201 212 - 93.8 (13.8) - 31 69
197 197 207 - 92.8 (12.7) - 30 67
192 192 202 - 91.9 (11.5) - 29 65
187 187 196 - 90.7 (10.0) - - 63

183 183 192 - 90 (9.0) - 28 63

179 179 188 - 89 (8.0) - 27 61
174 174 182 - 87.8 (6.4) - - 60
170 170 178 - 86.8 (5.4) - 26 58
167 167 175 - 86 (4.4) - 57

163 163 171 - 85 (3.3) - 25 56

156 156 163 - 82.9 (0.9) - 53
149 149 156 - 80.8 - 23 51
143 143 150 - 78.7 - 22 50
137 137 143 - 76.4 - 21 47

131 131 137 - 74 - - 46

126 126 132 - 72 - 20 44
121 121 127 - 69.8 - 19 42
116 116 122 - 67.6 - 18 41
111 111 117 - 65.7 - 17 39

General technical information

339
 Technical parameter

Material Conversion Table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS EN AFNOR SS UNI UNE JIS

Structural steel

15 C15 1.0401 1015 080M15 - CC12 1350 C15C16 F.111 -

20 C22 1.0402 1020 050A20 2C CC20 1450 C20C21 F.112 -

35 C35 1.0501 1035 060A35 - CC35 1550 C35 F.113 -

45 C45 1.0503 1045 080M40 - CC45 1650 C45 F.114 -

55 C55 1.0535 1055 070M55 - - 1655 C55 - -

60 C60 1.0601 1060 080A62 43D CC55 - C60 - -

Y15 9SMn28 1.0715 1213 230M07 - S250 1912 CF9SMn28 11SMn28 SUM22

- 9SMnPb28 1.0718 12L13 - - S250Pb 1914 CF9MnPb28 11SMnPb28 SUM22L

- 10SPb20 1.0722 - - - 10PbF2 - CF10Pb20 10SPb20 -

- 35S20 1.0726 1140 212M36 8M 35MF4 1957 - F210G -

Y13 9SMn36 1.0736 1215 240M07 1B S300 - CF9SMn36 12SMn35 -

- 9SMnPb36 1.0737 12L14 - - S300Pb 1926 CF9SMnPb36 12SMnP35 -

55Si2Mn 55Si9 1.0904 9255 250A53 45 55S7 2085 55Si8 56Si7 -

- 60SiCr7 1.0961 9262 - - 60SC7 - 60SiCr8 60SiCr8 -

15 Ck15 1.1141 1015 080M15 32C XC12 1370 C16 C15K S15C
P
40Mn 40Mn4 1.1157 1039 150M36 15 35M5 - - - -

25 Ck25 1.1158 1025 - - - - - - S25C

35Mn2 36Mn5 1.1167 1335 - - 40Mn5 2120 - 36Mn5 SMn438(H）

30Mn 28Mn6 1.117 1330 150M28 14A 20M5 - C28Mn - SCMn1

35Mn Cf35 1.1183 1035 060A35 - XS38TS 1572 C36 - S35C

Ck45 45 1.1191 1045 080M46 - XC42 1672 C45 C45K S45C

55 Ck55 1.1203 1055 070M55 - XC45 - C50 C55K S55C

50 Cf53 1.1213 1050 060A52 - XC48TS 1674 C53 - S50C

60Mn Ck60 1.1221 1060 080A62 43D XC60 1678 C60 - S58C

- Ck101 1.1274 1095 060A96 - - 1870 - - SUP4

- X120Mn12 1.3401 - Z120M12 - X120M12 - XG120Mn12 X120Mn12 SCMnH/1

GCr15 100Cr6 1.3505 52100 534A99 31 100C6 2258 100Cr6 F.131 SUJ2

ASTM
- 15Mo3 1.5415 1501-240 - 15D3 2912 16Mo3KW 16Mo3 -
A204Gr.A
1503-245-
- 16Mo5 1.5426 4520 - - - 16Mo5 16Mo5 -
420
ASTM
- 14Ni6 1.5622 - - 16N6 - 14Ni6 15Ni6 -
A350LF5
ASTM 1501-509;
- X8Ni9 1.5662 - - - X10Ni9 XBNi09 -
A353 510

340
Technical parameter

Material Conversion Table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS EN AFNOR SS UNI UNE JIS

Structural steel

- 12Ni19 1.5680 2515 - - Z18N5 - - - -

- 36NiCr6 1.5710 3135 640A35 111A 35NC6 - - - SNC236

SNC415
- 14NiCr10 1.5732 3415 - - 14NC11 - 16NiCr11 15NiCr11
(H)
SNC815
- 14NiCr14 1.5752 34153310 655M13655A12 36A 12NC15 - - -
(H)
38CrNiMo4
- 36CrNiMo4 1.6511 9840 816M40 110 40NCD3 - 35CrNiMo4 -
(KB)
SNCCM220
- 21NiCrMo2 1.6523 8620 850M20 362 20NCD2 2503 20NiCrMo2 20NiCrMo2
(H)
40NiCrMo2
- 40NiCrMo2 1.6546 8740 311-Type7 - - - 40NiCrMo2 SNC240
(KB)
35CrNiMo6
40CrNiMoA 34CrNiMo6 1.6582 4340 817M40 24 35NCD6 2541 - -
(KB)

- 17CrNiMo6 1.6587 - 820A16 - 18NCD6 - - 14CrNiMo1 -

15Cr 15Cr3 1.7015 5015 523M15 - 12C3 - - - SCr415(H)

35Cr 34Cr4 1.7033 5132 530A32 18B 32C4 - 34Cr4(KB) 35Cr4 SCr430(H)

40Cr 41Cr4 1.7035 5140 530M40 18 42C4 - 41Cr4 42Cr4 SCr440(H)

40Cr 42Cr4 1.7045 5140 - - - 2245 - 42Cr4 SCr440

P
18CrMn 16MnCr15 1.7131 5115 (527M20) - 16MC5 2511 16MnCr15 16MnCr15 -

20CrMn 55Cr3 1.7176 5155 527A60 48 55C3 - - - SUP9(A)

25CrMo4 SCM420;
30CrMo 25CrMo4 1.7218 4130 1717CDS110 - 25CD4 2225 55Cr3
(KB) SCM430
SCM432;
35CrMo 34CrMo4 1.7220 4137;4135 708A37 19B 35CD4 2234 35CrMo4 34CrMo4
SCRRM3

40CrMoA 41CrMo4 1.7223 4140;4142 708M40 19A 42CD4TS 2244 41CrMo4 41CrMo4 SCM440

42CrMo
42CrMo4 1.7225 4140 708M40 19A 42CD4 2244 42CrMo4 42CrMo4 SCM440(H)
42CrMnMo

- 15CrMo5 1.7262 - - - 12CD4 2216 - 12CrMo4 SCM415(H)

ASTMA182F11; 15CD3.5;
- 13CrMo44 1.7335 1501-620Gr.27 - - 14CrMo44 14CrMo45 -
F12 15CD4.5

- 32CrMo12 1.7361 - 722M24 40B 30CD12 2240 32CrMo12 F.124.A -

1501-
- 10CrMo910 1.7380 ASTMA182F.22 - 12CD9;10 2218 12CrMo9,10 TU.H -
622Gr.31;45

- 14MoV63 1.7715 - 1503-660-440 - - - - 13MoCrV6 -

50CrVA 50CrV4 1.8159 6150 735A50 47 50CV4 2230 50CrV4 51CrV4 SUP10
General technical information

- 41CrAlMo7 1.8509 - 905M39 41B 40CAD6,12 2940 41CrAlMo7 41CrAlMo7 -

- 39CrMoV139 1.8523 - 897M39 40C - - 36CrMoV12 - -

341
 Technical parameter

Material Conversion Table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS EN AFNOR SS UNI UNE JIS

Tool steel

C98KU F.515
T10 C105W1 1.1545 W.110 - - Y1105 1880 -
C100KU F.516

T12A C125W 1.1663 W.112 - - Y2120 - C120KU (C120) SK20

GCr15 100Cr6 1.2067 L3 BL3 - Y100C6 - - 100Cr6 -

X210Cr13KU
Cr12 X210Cr12 1.2080 D3 BD3 - Z200Cr12 - X210Cr12 SKD1
X250Cr12KU
X35CrMoV05KU
4Cr5MoVSi X40CrMoV5 1 1.2344 H13 BH13 - Z40CDV5 2242 X40CrMoV5 SKD61
X40CrMoV51KU

Cr6WV X100CrMoV5 1 1.2363 A2 BA2 - Z100CDV5 2260 X100CrMoV51KU X100CrMoV5 SKD12

SKS31
10WCr6
CrWMo 105WCr6 1.2419 - - - 105WC13 2140 105WCr5 SKS2
107WCr5KU
SKS3

Cr12W X210CrW12 1.2436 - - - - 2312 X215CrW12 1KU X210CrW12 SKD2

5CrNiMo 45WCrV7 1.2542 S1 BS1 - - 2710 45WCrV8KU 45WCrSi8 -

P X30WCrV93 X28W09KU
3Cr2W8V 1.2581 H21 BH21 - Z30WCV9 - X30WCrV9 SKD5
X30WCrV93KU X30WCrV9 3KU

Cr12MoV X165CrMoV 12 1.2601 - - - - 2310 X165CrMoW12KU X160CrMoV12 SKD11

5CrNiMo 55NiCrMoV6 1.2713 L6 - - 55NCDV7 - - F.250.S SKT4

V 100V1 1.2833 W210 BW2 - Y1105V - - - SKS43

W6Mo5Cr4V2Co5 S6-5-2-5 1.3243 - - - Z85WDKCV 2723 HS6-5-2-5 HS6-5-2-5 SKH55

Z80WKCV
W18Cr4VCo5 S18-1-2-5 1.3255 T4 BT4 - - X78WCo1805KU HS18-1-1-5 SKH3
10-05-04-01
Z85WDCV
W6Mo5Cr4V2 S6-5-2 1.3343 M2 BM2 - 2722 X82WMo0605KU HS6-5-2 SKH9
06-05-04-02

﹣Z﹣
Z100WCWV
- S2-9-2 1.3348 M7 - 2782 HS2-9-2 HS2-9-2 -
09-02-04-02
Z80WCV
W18Cr4V S18-0-1 1.3355 T1 BT1 - - X75W18KU HS18-0-1 SKH2
18-04-01

W6Mo5Cr4V3 S6-5-3 - M3 - - - - - - SKH52

- - - M42 BM42 - - - - - SKH59

342
Technical parameter

Material Conversion Table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS EN AFNOR SS UNI UNE JIS

Stainless steel

0Cr13;
403 1.4000 403 403S17 - Z6C13 2301 X6Cr13 F.3110 SUS403
1Cr12

- - 1.4001 - - - - - - F.8401 -

1Cr13 410 1.4006 410 410S21 56A X12Cr13 2302 X12Cr13 F.3401 SUS410

1Cr17 430 1.4016 430 430S15 60 X8Cr17 220 X8Cr17 F.3113 SUS430

2Cr13 410 1.4021 40 S62 56B;56C X20C13 - X20C13 F.3401 SUS410

- - 1.4027 - 420C29 56B - - - - SCS2

4Cr13 - 1.4034 - 420S45 56D X40Cr14 2304 X40Cr14 F.3405 SUS420J2

1Cr17Ni2 431 1.4057 431 431S29 57 X16CNi16 2321 X16CNi16 F.3427 SUS431

Y1Cr17 430F 1.4104 430F - - X10CrS17 2383 X10CrS17 F.3117 SUS430F

1Cr17Mo 434 1.4113 434 434S17 - X8CrMo17 2325 X8CrMo17 - SUS434

- - 1.4313 - 425C11 - - - - - SCS5

- - 1.4408 - 316C16 - - - - F.8414 SCS14

4Cr9Si2 HW3 1.4718 HW3 401S45 52 X45CrSi8 - X45CrSi8 F.322 SUH1

0Cr13Al 405 1.4724 405 403S17 - X10CrAl12 - X10CrAl12 F.311 SUS405

Cr17 430 1.4742 430 430S15 60 X8Cr17 - X8Cr17 F.3113 SUS430

M
8Cr20Si2Ni HNV6 1.4757 HNV6 443S65 59 X80CrSiNi20 - X80CrSiNi20 F.320V SUH4

2Cr25N 446 1.4762 446 - - X16Cr26 2322 X16Cr26 - SUH446

Austenitic stainless steel

F.3551
0Cr18Ni9 X5CrNi1810 1.4301 304 304S15 58E Z6CN18.09 2332 X5CrNi1810 F.3541; SUS304
F.3504

1Cr18Ni9MoZr X10CrNiS189 1.4305 303 303S21 58M Z10CNF18.09 2346 X10CrNiS18.09 F.3508 SUS303

0Cr19Ni10 X2CrNi1911 1.4306 304L 304S12 - Z2CN18.10 2352 X2CrNi18.11 F.3503 SCS19

- G-X6CrNi189 1.4308 - 304C15 - Z6CN18.10M - - - SCS13

Cr17Ni17 X12CrNi177 1.4310 301 - - Z12CN17.07 2331 X12CrNi1707 F.3517 SUS301

- X2CrNiN1810 1.4311 304LN 304S62 - Z2CN18.10 2371 - - SUS304LN

0Cr19Ni9 X5CrNi189 1.4350 304 304S31 58E Z6CN18.09 - X5CrNi1810 - SUS304

General technical information

X5CrNi Z6CND
0Cr17Ni11Mo2 1.4401 316 316S16 1.4401 2347 X5CrNiMo1712 F.3543 SUS316
Mo1712 17.11
X2CrNi
00Cr17Ni13Mo2 1.4429 316LN - - Z2CND17.13 2375 - - SUS316LN
MoN17133
X2CrNi
0Cr27Ni12Mo3 1.4435 316L 316S12 - Z2CDN17.13 2353 X2CrNiMo1713 - SCS16
Mo18143
X2CrNi
00Cr19Ni13Mo3 1.4438 317L 317S12 - Z2CND19.15 2367 X2CrNiMo18.16 - SUS317L
Mo17133
SUS329L;
- X8CrNiMo275 1.4460 329L - - - 2324 - - SCH11;
SCS11

343
 Technical parameter

Material Conversion Table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS EN AFNOR SS UNI UNE JIS

Austenitic stainless steel

X6CrNi
1Cr18Ni9Ti 1.4541 321 2337 321S12 Z6CNT18.10 58B X6CrNiTi1811 F.3553 SUS321
Ti1810
X6CrNi
1Cr18Ni11Nb 1.4550 347 347S17 58F Z6CNNb18.1 2338 X6CrNiTi1811 F.3552 SUS347
Nb1810
X6CrNi
Cr18Ni12Mo2Ti 1.4571 316Ti 320S17 58J Z6NDT17.12 2350 X6CrNiMoTi17 F.3535 -
MoTi17122
G-X5CrNi
- 1.4581 - 318C7 - Z4CNDNb1812M - XG8CrNiMo18 - SCS22
MoNb1810
X10CrNi
Cr17Ni12Mo3Nb 1.4583 318 - - Z6CNDNb1713B - X6CrNiMoTiNb17 - -
MoNb1812
M
X15CrNi
1Cr23Ni13 1.4828 309 309S24 - Z15CNS20.1 - - - SUH309
Si2012

0Cr25Ni20 X12CrNi2521 1.4845 310S 310S24 - Z12CN2520 2361 X6CrNi2520 F.331 SUH310

X12NiCr
Cr15Ni36W3Ti 1.4864 330 - - Z12CNS35.1 - - - SUH330
Si3616
G-X40NiCr
- 1.4865 - 330C11 - - - XG50NiCr3919 - SCH15
Si3818
X53CrMn 349S54; ﹣
5Cr2Mn9Ni4N 1.4871 EV8 Z52CMN21.0 - X53CrMnNiN219 - SUH35
NiN219 321S12 58B
X12CrNi
1Cr18Ni9Ti 1.4878 321 321S320 58C Z6CNT18.12 - X6CrNiTi1811 F.3523 SU321
Ti189

Country and standard

ISO China Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB W.-nr AISI/SAE EN AFNOR SS UNI UNE JIS

Nodular cast iron

QT400-18 GGG40 60-40-18 400/17 FGS370-17 0717-02 GS370-17 FGE38-17 FCD400

QT450-10 -- 65-45-12 420/12 FGS400-12 -- GS400-12 FGE42-12 FCD450

QT500-7 GGG50 70-50-05 500/7 FGS500-7 0727-02 GS500-7 FGE50-7 FCD500

QT600-3 GGG60 80-60-03 600/7 FGS600-2 0732-03 GS600-2 FGE60-2 FCD600

QT700-2 GGG70 100-70-03 700/2 FGS700-2 0737-01 GS700-2 FGE70-2 FCD700

QT800-2 GGG80 120-90-02 800/2 FGS800-2 0864-03 GS800-2 FGE80-2 FCD800

QT900-2 -- -- 900/2 -- -- -- -- --
K
Grey cast iron

-- GG40 NO.60 -- FGL400 0140 -- --

HT350 GG35 NO.50 350 FGL350 0135 G35 FG35 FC350

HT300 GG30 NO.45 300 FGL300 0130 G30 FG30 FC300

HT250 GG25 NO.35 250 FGL250 0125 G25 FG25 FC250

HT200 GG20 NO.30 200 FGL200 0120 G20 FG20 FC200

HT150 GG15 NO.20 150 FGL150 0115 G15 FG15 FC150

HT100 -- -- 100 -- 0110 G10 -- FC100

344
Technical parameter

Material Conversion table

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS AFNOR SS UNI UNE JIS

Al-based alloy

ZAlSi7Mg Al-Si7Mg(Fe) ~AlSi7Mg 356 LM25 A-S7G 4244 3599 - AC4C

ZAlSi7MgA Al-Si7Mg AlSi7Mg A356.0 2L99 A-S7G03 - 8024 - AC4C

ZAlSi12 Al-Si12 AlSi12 413;B413.0 LM6 A-S13 4261 4514 - AC3A

N ZAlSi9Mg ~Al-Si10Mg AlSi9Mg 360 LM9 A-S9G;A-S10G 4253 3051 - AC4A

- Al-Si5 AlSi5Mg A 443.0 - - - 5077 - -

- Al-Si5Fe - B443.0 - - - GD-AlSi5Fe - -

- (AlSi7Fe) - A444.0 - - - - - -

- Al-Si12Fe - 413 LM20 ~A-S12 4260 5079 - ADC1

Country and standard

ISO China International Germany U.S.A. U.K. France Sweden Italy Spain Japan

GB DIN W.-nr AISI/SAE BS AFNOR SS UNI UNE JIS

Ni-based alloy

- S-NiCr13A16MoNb LW2 4670 5391 mar ﹣ 46 NC12AD - - - -

- NiCo15Cr10MoAlTi LW2 4674 AMS 5397 - - - - - -

- NiFe35Cr14MoTi LW2.4662 5660 - ZSNCDT42 - - - -

- NiCr19Fe19NbMo LW2.4668 5383 HR8 NC19eNB - - - -

- NiCr20TiAk 2.4631 - Hr401.601 NC20TA - - - -

- NiCr19Co11MoTi 2.4973 AMS 5399 - NC19KDT - - - -

- NiCr19Fe19NbMo LW2.4668 AMS 5544 - NC20K14 - - - -

- - 2.4603 5390A - NC22FeD - - - -

- NiCr22Mo9Nb 2.4856 5666 - NC22FeDNB - - - -

S - NiCr20Ti 2.4630 - HR5.203-4 NC20T - - - -

- NiCu30AL3Ti 2.4375 4676 3072-76 - - - - -

Co-based alloy

- CoCr20W15Ni - 5537C,AMS - KC20WN - - - -

General technical information

- CoCr22W14Ni LW2.4964 5772 - KC22WN - - - -

Ti-alloy

- TiAl5Sn2.5 3.7115.1 UNS R54520 TA14/17 T-A5E - - - -

- - - - - UNS R56400 - - - -
TA10-13/
- TiAl6V4 3.7165.1 - UNS R56401 - T-A6V - -
TA28
- TiAl5V5Mo5Cr3 - - - - - - - -

- TiAl4Mo4Sn4Si0.5 3.7185 - - - - - - -

345
Index

-UF

-UF

346
 -UF

TCGT-UF -UF

347
"EESFTT
(BO[IPV
&DPOPNJD
%FWFMPQNFOU
"SFB
+JBOHYJ

$IJOB

1PTUDPEF


5FMF


'BY


&NBJM
FYQPSU!BDIUFDLUPPMDPN
8FCTJUF
XXXBDIUFDLUPPMDPN