CANYON METAL SCAFFOLDING 香港鰂魚涌華蘭路 20 號華蘭中心 605-606 室

Room 605-606, 6/F, Westlands Centre

ENGINEERING LIMITED 20 Westlands Road, Quarry Bay, Hong Kong
Tel: (852) 2885 9633 Fax: (852) 2567 1611
金源通架工程有限公司 Email: [email protected]
Website: http://www.canyonhk.com

STEEL FORMWORK & ACCESSORIES

Steel formwork systems for every size and shape of ground plan, in practical dimension & equipped with different
features to make shuttering more efficient. CANYON’s experienced engineers can provide customer oriented steel
formwork systems ranged from platform panels to column formworks. We have been serving the industry for over 20
years, and provide technical support & economical design as well as various accessories.

Flatform Panels Form Work for

Site : Shatin Recourse

Application of Push-pull Prop. &

Soldier System for
Site : Ma On Shan

Column Formwork for

Contract : Tai Po 161

CANYON utilizes the latest computer technology in computer aid design and drafting, & 3D graphic visualizations.
Whenever you require design, fabrication or virtual graphics. CANYON possesses the experience and technical
knowhow to offer a one-stop shop of services to meet all your temporary works requirements.

P.1/5 1st Aug 2009 / Rev 02

 STEEL FORM WORK & ACCESSORIES

Flat Form
Flat Form is used for forming planes such as
those of Square columns, walls, slab floors, etc.
By combining units of various sizes, flat form can
be made to serve a wide variety of purposes.

(1) Corner Angle

Steel Form for Corners

Form can be assembled easily and tightly (2) Outside Corner Form
by using the Corner Angle, Outside Corner
Form & Inside Corner Form
We can tailor-made various sizes of corner
to suit customer specific requirements &
application.

(4) “L” – type pin & U-clip

(3) Inside Corner Form

Drawing of the Box Culvert

Samples of Box Culvert Design

A combination of the Flat form

Panels & corners are illustrated in
the application of common Box
Culvert. With the combination of
our cuplok system, it provide
¾ Versatile : complete systems
made to meet the needs of
contractors;
¾ Easy to Use : quick assembly
& fixing
¾ Proven Design : fabricated
for tough working conditions

P.2/5 1st Aug 2009 / Rev 02

 TIE BAR & ACCESSORIES

D15 TIE BAR & ACCESSORIES

TIE BAR D15

Through Tie with Specialized Type thread for all
Formwork Systems.

- SWL 90kN (ultimate load 190kN)

- Yield Load 158kN
- Total Elongation at Fracture 12% minimum
- Yield Stress 890MPa minimum
- Ultimate Tensile Strength 1080MPa minimum
- Threaded High Strength Bar, 15mm across flat sides,
17mm Across Thread, Black Mill Finish.
- Right Hand 1 start thread
- Mill Length 5.8 or 6.0 Meter
- Manufactured using the TEMPCORE quench & self
temper process.
- Provide exceptional toughness and very durable surface.
- Can be welded*, bent & takes shearforces
- Self cleaning thread & vibration resistant speed thread.
* welding to be carried out by certified welders only, according to
manufacturer’s specs & approval.

DBA-1060SC
Steel Cone 100mm Long,
DNT-5585DWZ 30mm hex nut. 60mm dia base.
Double Wing Nut 85 X 55mm of Machine Made Steel thread.
malleable cast iron, zinc plated Recoverable (to be released
within 24 hours), Zinc
Plated/Galvanized.

DBA-1080SC
Steel Cone 100mm Long,
DNT-5585SWZ 30mm hex nut, 80mm dia base.
Single Wing Nut 85 X 55mm of Machine Made Steel thread.
malleable cast iron, zinc plated Recoverable (to be released
within 24 hours), Zinc
Plated/Galvanized.

DNT-0510RF
Washer Faced Wing Nut 100 Dia. DBA-1090SW
Base X 50mm of malleable cast Iron, Square Flat Washer 100mm X
zinc plated 90mm X 9mm, Hole Dia.
For Panel Type Formwork 19mm. Cold Formed, smooth
surface Zinc
Plated/Galvanized.

DNT-2030HX
20mm Long, 30mm hex. Nut.
Machine Made Steel thread, DBA-1313SRW
Zinc Plated/Galvanized. Square Ribbed Washer
To fix corners of formwork panels. 130mm X 130mm X 9mm, Hole
Dia. 19mm. Smooth surface.
Zinc Plated/ Galvanized
DNT-5030HX
50mm Long, 30mm Hex Nut
Machine Made Steel thread,
Zinc Plated/Galvanized.
DBA-1111COMB
Combi Nut Plate 119mm X
119mm. High Quality Cast
DNT-1030HXJT iron, easy to release and runs
100mm Long, 30mm Hex Joint Nut smoothly on the bar. Zinc
Machine Made Steel thread, Plated.
Zinc Plated/Galvanized.

P.3/5 1st Aug 2009 / Rev 02

 ANCHOR SCREW & PUSH PULL PROPS

Recoverable Anchor Screw

For your temporary fixing points,

lifting points for climbing forms,
clam forms, tunnel forms &
single face formwork.
This advanced design lets us
guarantee for at least 50 reuses,
- no more wasting money on
expensive stainless inserts,
- no more wire strand or
rebar loops to cut off …
- no more parts left in the
concrete

Push Pull Props

- For faster plumbing and safe positioning of precast

units.
- A versatile, well engineered and complete system
flexible and economic.
- Takes tension and compression forces
- Handles always in workmen’s reach
- 3-dimensional operating swivel end for any slope or
angle by using one bolt only.
- Positively safe with permissible load up to 40kN on
compression & tension.

Product Code DPP-0900 DPP-1800 DPP-2600

Adjustment 900 – 1500mm 1800 – 3200mm 2600 – 4000mm

Perm. Load at 45。

On compression 43 kN 43 – 14 kN 43 – 10.9 kN
On tension 48.5 kN 48.5 kN 48.5 kN

Approx. Weight
19 28 40
(kg)

Outer Tube Ømm 76mm 76mm 76mm

P.4/5 1st Aug 2009 / Rev 02

 STEEL SOLDIER SYSTEM

Steel Soldier System

- Open web allows ties to be placed at virtually any
height.
Cross Section
- Compact & light – easy to handle
- Shallow depth permits formwork to be supported
very close to internal corners.
- Highly efficient, minimizing the needs for ties,
whilst at the same time being resistant to site
abuse & damage.
- A variety of formwork accessories allow the
Soldier to be used as a heavy duty Vertical or
Raking Shore or as a Yoke.
- Moment of resistance 38kNm.

When used in conjunction with shoring

component the Steel Soldier can be utilized
as a raking or vertical shore.

As a Raking Shore
To attach a Soldier used in the conventional manner,
the Head Screw of the Shore is secured by a Universal
Locating Pin through one of the holes located at the
Four sizes satisfy virtually all formwork requirements,
intervals along the soldier. Adjustment of the Raking and may be bolted end to end using four M16 X
shore is made by rotating the Soldier. 35HT Set screw. Max Bending moment 10kNm
Forkhead
Joint to joint connection

To fix MKll Soldiers end to end.

Four nos M16 x 35HT (Grade 8.8)
Set screw and nuts should be used.
Max bending moment= 10kNm

Joint reinforcement plate

Shoring Adaptor
When it is necessary to increase the capacity
bending moment at the joint of two soldier.
Four nos joint reinforcement plates may be
used complete with M16 x 50HT (grade 8.8)
set screw & nuts

Max bending moment = 15kNm

Joint reinforcement plate

Swivel Shoring Base

P.5/5 1st Aug 2009 / Rev 02