Scribd
Upload
12 views

Tutorial 4

tutorial

Uploaded by

vasanthdhilip65
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
12 views

Tutorial 4

tutorial

Uploaded by

vasanthdhilip65
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Reg. No.

K.S. RANGASAMY COLLEGE OF TECHNOLOGY, TIRUCHENGODE - 637 215


MECH
(AUTONOMOUS)

Tutorial IV
Programme & Branch B.Tech & Textile Technology Year/Sem II / III
Course Code & Name 60 ME 005 & Elements of Mechanical Engineering Date 04.10.2024
Maximum Marks 50 Time 1.30 to 3.10 p.m.

Blooms
S. No. Questions CO Mark
Level
1 A pinion having 30 teeth drives a gear having 80 teeth. The profile of the Ap 03 13
gears is involute with 20° pressure angle, 12 mm module and 10 mm
addendum. Find the length of path of contact, arc of contact and the contact
ratio.
2 Two involute gears of 20° pressure angle are in mesh. The number of teeth Ap 03 13
on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5
mm and the pitch line speed is 1.2 m/s, assuming addendum as standard
and equal to one module, find : 1. The angle turned through by pinion when
one pair of teeth is in mesh ; and 2. The maximum velocity of sliding.
3 Two involute gears in a mesh have a module of 8 mm and pressure angle of Ap 03 15
20. The larger gear has 57 while the pinion has 23 teeth. If the addenda on
pinion and gear wheels are equal to one module, find the (i) contact ratio (ii)
angle of action of the pinion and the gear wheel (iii) ration of the sliding to
rolling velocity at the (a) beginning of contact (b) pitch point (c) end of contact.
4 A compound gear train shown in figure consists of compound gears B-C and Ap 03 10
D-E. All gears are mounted on parallel shafts. The motor shaft rotating at 800
rpm is connected to the gear A and the output shaft to the gear F. The number
of teeth on gears A, B, C, D, E and F are 24,56,30,80,32 and 72 respectively.
Determine the speed of the gear.

Blooms Level Marks


Apply 50
Total 50
Q.No. Course Outcomes Marks
1, 2, 3 & 4 CO3: Select and design the appropriate power transmission drives for various requirements 50

Course Instructor Module C oordinator


Dr.K.Santhanam Dr. K. Mohan
K.S. RANGASAMY COLLEGE OF TECHNOLOGY, TIRUCHENGODE - 637 215
MECH
(AUTONOMOUS)

Tutorial IV – Answer Key


Programme & Branch B.Tech & Textile Technology Year/Sem II / III
Course Code & Name 60 ME 005 & Elements of Mechanical Engineering Date 04.10.2024
Maximum Marks 50 Time 1.30 to 3.10 p.m.

Blooms
S. No. Questions CO Mark
Level
1 A pinion having 30 teeth drives a gear having 80 teeth. The profile of the Ap 03 13
gears is involute with 20° pressure angle, 12 mm module and 10 mm
addendum. Find the length of path of contact, arc of contact and the contact
ratio.

2 Two involute gears of 20° pressure angle are in mesh. The number of teeth Ap 03 13
on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5
mm and the pitch line speed is 1.2 m/s, assuming addendum as standard
and equal to one module, find : 1. The angle turned through by pinion when
one pair of teeth is in mesh ; and 2. The maximum velocity of sliding.
3 Two involute gears in a mesh have a module of 8 mm and pressure angle of Ap 03 15
20. The larger gear has 57 while the pinion has 23 teeth. If the addenda on
pinion and gear wheels are equal to one module, find the (i) contact ratio (ii)
angle of action of the pinion and the gear wheel (iii) ration of the sliding to
rolling velocity at the (a) beginning of contact (b) pitch point (c) end of contact.
4 A compound gear train shown in figure consists of compound gears B-C and Ap 03 10
D-E. All gears are mounted on parallel shafts. The motor shaft rotating at 800
rpm is connected to the gear A and the output shaft to the gear F. The number
of teeth on gears A, B, C, D, E and F are 24,56,30,80,32 and 72 respectively.
Determine the speed of the gear.

Blooms Level Marks


Apply 50
Total 50
Q.No. Course Outcomes Marks
1, 2, 3 & 4 CO3: Select and design the appropriate power transmission drives for various requirements 50

Course Instructor Module C oordinator


Dr.K.Santhanam Dr. K. Mohan

You might also like