Shenzhen Global Test Service Co.,Ltd.

No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road,
Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong

TEST REPORT
Report Reference No. ..................... : GTS20200511012-1-1
Compiled by
( position+printed name+signature) .. :
File administrators Tracy Hu
Supervised by
( position+printed name+signature) .. :
Test Engineer Moon Tan
Approved by
( position+printed name+signature) .. :
Manage Simon Hu
Date of issue ..................................... : May. 25, 2020
Test Laboratory Name ...................... : Shenzhen Global Test Service Co.,Ltd.
Address............................................. : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative
Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu
Street, Longgang District, Shenzhen, Guangdong
Applicant’s name ............................ : Guangzhou Shangke Information Technology Limited.
Address............................................. : Room 1205-1212, NO.30 Huaxia Road, Tianhe District, Guangzhou,
Guangdong Province, China
Test specification .......................... :
Standard ........................................... : MIC Notice No.88 Appendix No.43 Article 2 Paragraph 1 Item 19
TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd.
Master TRF ....................................... : Dated 2014-12
Shenzhen Global Test Service Co.,Ltd. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen
Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global
Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the
reader's interpretation of the reproduced material due to its placement and context.
Test item description ..................... : Laptop
Trade Mark ....................................... : N/A
Manufacturer .................................... : Guangzhou Shangke Information Technology Limited.
Model/Type reference ....................... : F7 Plus
X6 Plus, F8, F9, F7, TG01, TG03, TG07, TG08, TG09, TG10, TG11,
List Model ......................................... : TG12, TG13, TG15, TG19, TG20, TG21, TG23, TB01, TB02, TB03,
TB04, TB05, TB06, TB10, TE10, TE11, TE12, TE13
Operation Frequency ........................ : From 2402MHz to 2480MHz
Modulation Type ............................... : GFSK, π/4-DQPSK, 8DPSK
Hardware version ............................. : X133G REV 5.1
Software version ............................... : Windows RS4
DC 7.6V by battery
Ratings.............................................. :
Recharged by DC 12.0V/2.0A
Result................................................ : PASS
Report No.: GTS20200511012-1-1 Page 2 of 44

TEST REPORT

May. 25, 2020

Test Report No. : GTS20200511012-1-1
Date of issue

Equipment under Test : Laptop

Model /Type : F7 Plus

Listed model : X6 Plus, F8, F9, F7, TG01, TG03, TG07, TG08, TG09, TG10, TG11,
TG12, TG13, TG15, TG19, TG20, TG21, TG23, TB01, TB02, TB03,
TB04, TB05, TB06, TB10, TE10, TE11, TE12, TE13

Applicant : Guangzhou Shangke Information Technology Limited.

: Room 1205-1212, NO.30 Huaxia Road, Tianhe District, Guangzhou,

Address
Guangdong Province, China

Manufacturer : Guangzhou Shangke Information Technology Limited.

: Room 1205-1212, NO.30 Huaxia Road, Tianhe District, Guangzhou,

Address
Guangdong Province, China

Test Result: PASS

The test report merely corresponds to the test sample.

It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.
Report No.: GTS20200511012-1-1 Page 3 of 44

Contents
1. TEST STANDARDS ......................................................................................................................................... 4
2. SUMMARY ....................................................................................................................................................... 5
2.1. General Remarks .................................................................................................................................. 5
2.2. General Description of EUT................................................................................................................... 5
2.3. Equipment Under Test ........................................................................................................................... 6
2.4. Table for Parameters of Test Software Setting ...................................................................................... 6
2.5. Description of Test Modes ..................................................................................................................... 6
2.6. EUT configuration .................................................................................................................................. 7
2.7. Modifications .......................................................................................................................................... 7
3. TEST ENVIRONMENT ..................................................................................................................................... 8
3.1. Address of the test laboratory ................................................................................................................ 8
3.2. Test Facility ............................................................................................................................................ 8
3.3. Environmental conditions ...................................................................................................................... 8
3.4. Test Description ..................................................................................................................................... 8
3.5. Measurement Uncertainty ..................................................................................................................... 9
3.6. Measurement Instruments List .............................................................................................................. 9
4. TEST CONDITIONS AND RESULTS ............................................................................................................ 10
4.1. Frequency Error ................................................................................................................................... 10
4.2. Antenna Output Power and Output Power Tolerance.......................................................................... 12
4.3. Occupied Bandwidth and Spreading Bandwidth ................................................................................. 14
4.4. Dwell time ............................................................................................................................................ 18
4.5. Unwanted Emission Strength .............................................................................................................. 20
4.6. Secondary Radiated Emission Strength .............................................................................................. 30
4.7. Construction protection method........................................................................................................... 34
4.8. Interference Prevention Function ........................................................................................................ 34
4.9. Number of Carriers .............................................................................................................................. 34
5. TEST SETUP PHOTOS OF THE EUT ........................................................................................................... 35
6. EXTERNAL AND INTERNAL PHOTOS OF THE EUT .................................................................................. 36
Report No.: GTS20200511012-1-1 Page 4 of 44

1. TEST STANDARDS
The tests were performed according to following standards:

MIC Notice No.88 Appendix No.43 Article 2 Paragraph 1 Item 19

ARIB STD-T66 V3,7

Report No.: GTS20200511012-1-1 Page 5 of 44

2. SUMMARY
2.1. General Remarks
Date of receipt of test sample : May.19, 2020

Testing commenced on : May.20, 2020

Testing concluded on : May.25, 2020

2.2. General Description of EUT

Product Name: Laptop

Trade Mark: N/A
Model/Type reference: F7 Plus
X6 Plus, F8, F9, F7, TG01, TG03, TG07, TG08, TG09, TG10, TG11, TG12,
List Model: TG13, TG15, TG19, TG20, TG21, TG23, TB01, TB02, TB03, TB04, TB05,
TB06, TB10, TE10, TE11, TE12, TE13
Model Declaration PCB board, structure and internal of these model(s) are the same, So
no additional models were tested.
DC 7.6V by battery
Power supply:
Recharged by DC 12.0V/2.0A
WIFI
WLAN Supported 802.11 a/b/g/n/ac
IEEE 802.11a: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK)
IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
Modulation Type
IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11ac20/40/80: OFDM(256QAM,64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11a:5180-5240MHz
IEEE 802.11b:2412-2472MHz
IEEE 802.11g:2412-2472MHz
IEEE 802.11n HT20:2412-2472MHz, 5180-5240MHz
Operation frequency
IEEE 802.11n HT40:2422-2462MHz, 5190-5230MHz
IEEE 802.11ac20:5180-5240MHz
IEEE 802.11ac40:5190-5230MHz
IEEE 802.11ac80:5210MHz
11 Channels for WIFI 20MHz Bandwidth(802.11b/g/n-HT20)
7 Channels for WIFI 40MHz Bandwidth(802.11n-HT40)
Channel number 4 channels for 20MHz bandwidth(5180-5240MHz)
2 channels for 40MHz bandwidth(5190~5230MHz)
1 channels for 80MHz bandwidth(5210MHz)
BT
Operation frequency 2402-2480MHz
79 channels for Bluetooth (DSS)
Channel Number
40 channels for Bluetooth (DTS)
1MHz for Bluetooth (DSS)
Channel Spacing
2MHz for Bluetooth (DTS)
GFSK, π/4-DQPSK, 8DPSK for Bluetooth (DSS)
Modulation Type
GFSK for Bluetooth (DTS)
Two same FPC Antenna, but not support MIMO technology
ANT0(MAIN) used for BT / WIFI TX/RX, 0.78dBi(Max.) for 2.4G Band
Antenna Description and 0.63dBi(Max.) for 5G Band.
ANT1(AUX) used for WIFI TX/RX, 0.78dBi(Max.) for 2.4G Band and
0.63dBi(Max.) for 5G Band
Note: For more detailed features description, please refer to the manufacturer’s specifications or the User's
Manual.
Report No.: GTS20200511012-1-1 Page 6 of 44

2.3. Equipment Under Test

Power supply system utilised

Power supply voltage : ○ 120V / 60 Hz ○ 230V / 50Hz

○ 12 V DC ○ 24 V DC
● Other (specified in blank below)

DC 7.6 V from battery

2.4. Table for Parameters of Test Software Setting

During testing, Channel & Power Controlling Software provided by the customer was used to control the
operating channel as well as the output power level. The RF output power selection is for the setting of RF
output power expected by the customer and is going to be fixed on the firmware of the final end product.
Power Parameters:
Test Software Version DRTU
Frequency 2402MHz 2441MHz 2480MHz
Bluetooth Default Default Default

2.5. Description of Test Modes

The EUT has been tested under typical operating condition. The Applicant provides communication tools
software to control the EUT for staying in continuous transmitting and receiving mode for testing.
Operation Frequency List：

Channel Frequency (MHz)

00 2402
01 2403
...

...

38 2440
39 2441
40 2442
...

...

77 2479
78 2480

Note: Test performed at the lowest/middle/highest frequencies selected in the list above for EUT supported
while working on specified mode.
Report No.: GTS20200511012-1-1 Page 7 of 44

Sumarry of measurement results

EUT and Module Power tables

Normal High(+10%) Low(-10%)
EUT Setup Value(Vac)
100 110 90
Module Vdd Power Normal High(+10%) Low(-10%)
Measurement Value(Vdc) 3.302 3.305 3.295
Result Ref.level 0.09 -0.21
Voltage error(%)
Limit --- ±1
Judgment --- pass pass

NOTE:When EUT be operated at 10% from the normal supply voltage,the supply voltage of RF part
was varied within ±1%.All test cased were done under the normal supply voltage.

2.6. EUT configuration

The following peripheral devices and interface cables were connected during the measurement:

● - supplied by the manufacturer

○ - supplied by the lab

● adapter Length (m) : 1.5m

Shield : Non-Shielded
Detachable : Non- Detachable

2.7. Modifications
No modifications were implemented to meet testing criteria.
Report No.: GTS20200511012-1-1 Page 8 of 44

3. TEST ENVIRONMENT
3.1. Address of the test laboratory
Shenzhen Global Test Service Co.,Ltd.
No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road,
Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong

3.2. Test Facility

The test facility is recognized, certified, or accredited by the following organizations:

CNAS (No. CNAS L8169)

Shenzhen Global Test Service Co., Ltd. has been assessed and proved to be in compliance with CNAS-CL01
Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC 17025: 2017 General
Requirements) for the Competence of Testing and Calibration Laboratories.

A2LA (Certificate No. 4758.01)

Shenzhen Global Test Service Co., Ltd. has been assessed by the American Association for Laboratory
Accreditation (A2LA). Certificate No. 4758.01.

3.3. Environmental conditions

During the measurement the environmental conditions were within the listed ranges:

Normal Temperature: 25 °C
High Temperature: 55 °C
Low Temperature: -20 °C
Normal Voltage : DC 7.6V
High Voltage:DC 8.7V
Low Voltage:DC 6.5V
Relative Humidity: 55 %
Air Pressure: 989 hPa

3.4. Test Description

MIC Notice No.88 Appendix No.43 Article 2 Paragraph 1 Item 19

Description of Test
Clause Result
(Transmitter Parameters)
6 Antenna Power PASS
6 Tolerances for Antenna Power PASS
3 Frequency Tolerance PASS
4 Transmission Rate PASS
4 Occupied Frequency Bandwidth PASS
4 Spread Bandwidth PASS
13 Dwell Time PASS
5 Spurious Emissions PASS
Transmission Antenna Gain
10 PASS
(EIRP Antenna Power)
Transmission Radiated Angle Width
11 N/A
(3dB Beam width)
12 Interference prevention function PASS
8 Carrier Sensing function N/A
Receiver Parameters
7 Secondary Radiated Emissions PASS
N/A is an abbreviation for Not Applicable.
Report No.: GTS20200511012-1-1 Page 9 of 44

3.5. Measurement Uncertainty

For the test methods, according to the present document, the measurement uncertainty figures shall be
calculated in accordance with TR100028-1 [2] and shall correspond to an expansion factor (coverage factor)
K=1.96 or K=2 (which provide confidence levels of respectively 95% and 95.5% in the case where the
distributions characterizing the actual measurement uncertainties are normal.

Parameter Uncertainty
-6
Frequency error / 99%&90% bandwidth ±1.62*10
Total RF power, conducted ±0.8dB
Spurious emissions, conducted ±0.8dB
DC and low frequency voltages ±0.05%
Humidity ±5%
Temperature ±1℃

3.6. Measurement Instruments List

Cal.
Item Equipment Manufacturer Model No. Serial No. Last Cal.
Interval
1 Spectrum Analyzer Agilent N9020A MY48010425 2019/09/19 1

2 RF Cable H&S GTS-C008 --- 2019/09/19 1

3 DC Power Supply Yizhan PS-202D 40015841 2019/09/19 1

Calibration by the calibration agencies listed in the table correspond to paragraph 4 (ii) (c) of Article 24-2 in the
Radio Law".
Report No.: GTS20200511012-1-1 Page 10 of 44

4. TEST CONDITIONS AND RESULTS

4.1. Frequency Error
LIMIT

50ppm

TEST CONFIGURATION

SPECTRUM
EUT
ANALYZER

TEST PROCEDURE

The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block
diagram as TEST CONFIGURATION shows.
EUT Condition: non-modulation
Spectrum Condition:
• Frequency: test frequency
• Span: 300 KHz
• RBW: 1 KHz
• VBW: 30 KHz
• Sweep time: Auto
• Detector mode: Positive peak
• Indication mode: max hold

TEST RESULTS

Frequency Deviation Tolerance Limit

Test Condition Read (MHz) Result
(MHz) (MHz) (ppm) (ppm)
2402.00 2401.992 -0.008 -3.33

Non-modulation 2441.00 2440.993 -0.007 -2.87 50.00 Pass

2480.00 2479.992 -0.008 -3.23
Report No.: GTS20200511012-1-1 Page 11 of 44

2402 MHz

2441MHz

2480MHz
Report No.: GTS20200511012-1-1 Page 12 of 44

4.2. Antenna Output Power and Output Power Tolerance

LIMIT

 ≤ 3 mW /MHz(FHSS from 2402-2480 MHz)

 ≤ 10 mW/MHz (OFDM, DSSS from 2400-2483.5 MHz)
 ≤ 10 mW (other from 2400-2483.5 MHz)

The Output Power Tolerance must be within +20%, -80%.

E.i.r.p:
 ≤12.14dBm/MHz(OFDM,DS form 2400-2483.5MHz)
Note: E.I.R.P will not be applied to the transmission antenna which has a gain of 2.14dBi or less.

TEST CONFIGURATION

TEST PROCEDURE

a. EUT have transmitted continuous maximum power

b. Antenna Power Error is definition that actual measure antenna power tolerance between +20% to
-80% power range that base on manufacturer declare the conducted power density.

c.The EUT was programmed to be in continuously transmitting mode.

 Report No.: GTS20200511012-1-1 Page 13 of 44

TEST RESULTS

Average Spread Rated

Duty Output
burst Bandwi Limit output
Modulation cycle power Tolerance
mode power dth (mW/ power Limit Result
type (mW/M (%)
MHz) (mW/M
(dBm) (MHz) Hz)
Hz)
GFSK Hopping 4.31 0.30 70.790 0.13 3 0.2 -35.00
-80%
π/4-DQPSK Hopping 0.70 0.30 70.865 0.06 3 0.1 -40.00 ~20 Pass
%
8DPSK Hopping 0.93 0.30 70.775 0.06 3 0.1 -40.00
Remark:

Output power= Average value / (Duty Cycle * Spreading bandwidth)

Test Result of EIRP

Conduted test Measured EIRP Limit
Mode mode Antenna gain
Power(mW/MHz) Value(dBm/MHz) (dBm/MHz)
GFSK Hopping 0.13 0.78 -8.18 6.91
π/4-DQPSK Hopping 0.06 0.78 -11.80 6.91
8DPSK Hopping 0.06 0.78 -11.56 6.91

Note: Declared E.I.R.P= Conduted test Power+ Antenna gain

Report No.: GTS20200511012-1-1 Page 14 of 44

4.3. Occupied Bandwidth and Spreading Bandwidth

LIMIT

• Occupied bandwidth: FH≤83.5 MHz; OFDM≤38 MHz, DS≤26 MHz; Others≤26 MHz
• Spread Bandwidth:≥ 500 kHz(FH,DS)
• Spread factor>5.

TEST CONFIGURATION

SPECTRUM
EUT
ANALYZER

TEST PROCEDURE

1. Setting of SA is following as fellow:

• RBW: under 3% of OBW
• VBW: = RBW
• Sweep time: Auto
• Sweep Mode: Continuous sweep
• Detect mode: Positive peak
• Trace mode: Max hold
2. EUT have transmitted the maximum modulation signal and fixed channelize. SA set to 99% of occupied
bandwidth to measure occupied bandwidth.
3. EUT have transmitted the maximum modulation signal and fixed channelize. SA set to 90% of occupied
bandwidth to measure spread bandwidth.
4. Spread Factor=Spread Bandwidth/modulation rate. The modulation rate: MR=1Mbps (declare by client)

TEST RESULTS

Occupy Bandwidth
Type Channel (MHz) Limit (MHz) Result
(MHz)
GFSK 2402-2480 78.586
π/4-DQPSK 2402-2480 78.647 <83.5 Pass
8DPSK 2402-2480 78.683
Report No.: GTS20200511012-1-1 Page 15 of 44

Bluetooth BR/EDR

GFSK

π/4-DQPSK

8DPSK
Report No.: GTS20200511012-1-1 Page 16 of 44

Bluetooth BR/EDR
Spread
Channel Spread Spread Bandwidth Spread
Type Bandwidth Result
(MHz) Factor Limit (MHz) Factor Limit
(MHz)
GFSK 2402-2480 70.733 70.733
π/4-DQPSK 2402-2480 70.396 53.330 ≥0.5 >5 Pass
8DPSK 2402-2480 70.694 53.556
Note: Spread Factor=Spread Bandwidth/modulation rate. The modulation rate: MR=1Mbps/2Mbps3Mbps
(declare by client)
Report No.: GTS20200511012-1-1 Page 17 of 44

Bluetooth BR/EDR

GFSK

π/4-DQPSK

8DPSK
Report No.: GTS20200511012-1-1 Page 18 of 44

4.4. Dwell time

LIMIT

0.4 second or less

NOTE: Dwell time only applicable to HFSS system device.

TEST CONFIGURATION

SPECTRUM
EUT
ANALYZER

TEST PROCEDURE

The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block
diagram as TEST CONFIGURATION shows.
EUT Condition: modulation
Spectrum Condition:
• Frequency: test channel
• Span=0MHz
• RBW: 1MHz
• VBW: 1MHz
• Sweep time: Auto
• Detector mode: Positive peak

TEST RESULTS

transmission burst Dwell

spreading cycle Channel Limit
Type time of 1 burst time Result
rate numbers (second)
(ms) (ms) (second)
DH1/2-DH1/3-DH1 70.790 0.38 1.25 79 0.109
DH3/2-DH3/3-DH3 70.865 1.63 2.5 79 0.234 0.4 Pass
DH5/2-DH5/3-DH5 70.775 2.88 3.75 79 0.275

Remark: Dwell time=0.4 x (spreading rate)x(transmission time of 1 burst)/[(burst cycle)x(No. of hopping

channels)]
Spreading rate= [spread bandwidth (actual measurement value)]/ transmission rate
Transmission rate is 1Mbps (declare by client)
Report No.: GTS20200511012-1-1 Page 19 of 44

Bluetooth BR/EDR

GFSK, π/4-DQPSK, 8DPSK(DH1/2-DH1/3-DH1)

GFSK, π/4-DQPSK, 8DPSK(DH3/2-DH3/3-DH3)

GFSK, π/4-DQPSK, 8DPSK (DH5/2-DH5/3-DH5)

Report No.: GTS20200511012-1-1 Page 20 of 44

4.5. Unwanted Emission Strength

LIMIT

Below 2387 MHz: 2.5μW/MHz or less

2387 to 2400 MHz: 25μW/MHz or less
2483.5 Through 2496.5 MHz: 25μW/MHz or less
Over 2496.5 MHz: 2.5μW/MHz or less

TEST CONFIGURATION

SPECTRUM
EUT
ANALYZER

TEST PROCEDURE

The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block
diagram as TEST CONFIGURATION shows.
EUT Condition: modulation
Spectrum Condition:
• Frequency: 30MHz-13GHz
• RBW: 100 KHz (30MHz-1GHz), 1MHz (1GHz-12.5GHz)
• VBW: 100 KHz (30MHz-1GHz), 1MHz (1GHz-12.5GHz)
• Sweep time: Auto
• Detector mode: Positive peak
• Indication mode: max hold
NOTE:30~1000MHz,limit is 2.5uW/MHz=-26dBm/MHz=-36dBm/100KHz

TEST RESULTS
Report No.: GTS20200511012-1-1 Page 21 of 44

Bluetooth BR/EDR

Test mode: GFSK Test channel： 2402MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 22 of 44

Test mode: GFSK Test channel: 2441MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 23 of 44

Test mode: GFSK Test channel： 2480MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 24 of 44

Test mode: π/4-DQPSK Test channel： 2402MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 25 of 44

Test mode: π/4-DQPSK Test channel： 2441MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 26 of 44

Test mode: π/4-DQPSK Test channel： 2480MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 27 of 44

Test mode: 8DPSK Test channel： 2402MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 28 of 44

Test mode: 8DPSK Test channel： 2441MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 29 of 44

Test mode: 8DPSK Test channel： 2480MHz

30MHz~2.387GHz 2.387GHz~2.4 GHz

2.4835GHz~2.4965GHz 2.4965GHz~12.5GHz
Report No.: GTS20200511012-1-1 Page 30 of 44

4.6. Secondary Radiated Emission Strength

LIMIT

Below 1GHz: 4.0nW or less

Above 1GHz: 20nW or less

TEST CONFIGURATION

SPECTRUM
EUT
ANALYZER

TEST PROCEDURE

The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block
diagram as TEST CONFIGURATION shows.
EUT Condition: modulation
Spectrum Condition:
• Frequency: 30MHz-13GHz
• RBW: 100 KHz (30MHz-1GHz), 1MHz (1GHz-12.5GHz)
• VBW: 100 KHz (30MHz-1GHz), 1MHz (1GHz-12.5GHz)
• Sweep time: Auto
• Detector mode: Positive peak
• Indication mode: max hold

TEST RESULTS
Report No.: GTS20200511012-1-1 Page 31 of 44

Bluetooth BR/EDR
Test mode: GFSK

2402MHz

2441MHz

2480MHz
Report No.: GTS20200511012-1-1 Page 32 of 44

Test mode: π/4-DQPSK

2402MHz

2441MHz

2480MHz
Report No.: GTS20200511012-1-1 Page 33 of 44

Test mode: 8DPSK

2402MHz

2441MHz

2480MHz
Report No.: GTS20200511012-1-1 Page 34 of 44

4.7. Construction protection method

Requirement

The high-frequency section and modulation section of the radio equipment except for the antenna system shall
not be capable of being opened easily

Confirmation method

All high-frequency section and modulation section packet in one IC, End user can not modify easily.

4.8. Interference Prevention Function

Requirement

Clarify the one automatically to transmit and to receive identification code with the wireless equipment of the
wireless station used in the same premises.

Interference Prevention Function Confirm

A communication link was made where the ID code is correct (Identical).

TEST PROCEDURE

1. Connect the EUT in network

2. Open the software
3. We can get the information as follows:

TEST RESULTS

The radio equipment has an identification code. A verification of this code is done before a communication
channel is established.

MAC Address:ACF55J90141N

4.9. Number of Carriers

LIMIT

The number of Carriers: 1 or more/MHz

TEST RESULTS

This device has more than 1 subcarrier in 1MHz, compliances with the requirement
Report No.: GTS20200511012-1-1 Page 35 of 44

5. TEST SETUP PHOTOS OF THE EUT

Report No.: GTS20200511012-1-1 Page 36 of 44

6. EXTERNAL AND INTERNAL PHOTOS OF THE EUT

Fig. 1

Fig. 2
Report No.: GTS20200511012-1-1 Page 37 of 44

Fig. 3

Fig. 4
Report No.: GTS20200511012-1-1 Page 38 of 44

Fig. 5

Fig. 6
Report No.: GTS20200511012-1-1 Page 39 of 44

Fig. 7

Fig. 8
Report No.: GTS20200511012-1-1 Page 40 of 44

Fig. 9

Fig. 10
Report No.: GTS20200511012-1-1 Page 41 of 44

Fig. 11

Fig. 12
Report No.: GTS20200511012-1-1 Page 42 of 44

Fig. 13

Fig. 14
Report No.: GTS20200511012-1-1 Page 43 of 44

Fig. 15

Fig. 16
Report No.: GTS20200511012-1-1 Page 44 of 44

Fig. 17

**********************THE END**********************