ENGINEERING STUDIES TEST 2 SCOPE

Subjects Level MODULES TEST 2

Module 01 –Fundamentals of Brickwork and Plastering theory
Module 02 –Brick Bonding
Bricklaying N2 Module 03 –Preparation of Surface Materials
Module 04 –Manufacturing of bricks
Module 05 -Arches
MODULE 2&5: FOUNDATIONS AND FLOORS
MODULE 6: ROOFS AND ROOF COVERINGS
Building Drawing N2 MODULE 10: DOORS
MODULE 3: BRICKWORK
MODULE 11: MATERIALS
MODULE 1: AC CIRCUIT THEORY
MODULE 2: CONDUCTORS, INSULATORS & CABLES
MODULE 3: ELECTRICAL RETICULATION
MODULE 4: SWITCHGEARS
Elect Trade Theory N2
MODULE 5: BATTERIES
MODULE 6: DIRECT-CURRENT MACHINES
MODULE 7: ALTERNATING CURRENT MACHINES
MODULE 8: TRANSFORMRES
Module 1 DYNAMICS: Conversions,
Module 2 Statics Beams(word problems),Theory,
Module 4: Work done calculations,power&efficiency calculations
Engineering Science N2 Module 5 : Mechanical Drives & Lifting Machines : Calculations, Defintions,Chain
advantages and disadvabtages
Module 6 : Friction calculations
Module 7: Heat calculations
1. OCCUPATIONAL SAFETY
2. LIMITS and FITS
Fitting and machining N2 3. BEARINGS
4. LUBRICATION
5. PUMPS
 6.COMPRESSORS
6. VALVES
7. BELTDRIVES
8. GEAR DRIVES
MODULE 1 : Direct Current Theory :-
1. Resistance , resistivity and
temperature coefficient.
2. Resistor circuits
3. Kirchoff’s Laws and application to solve various resistive circuits
Module 3: Semiconductor Physics
Industrial Elect N2
1. Atomic Theory
2. Semiconductor Diodes – various types and characteristics
3. Diode as a rectifier.
4. Transistor Circuits
Module 4 : Measuring Instruments
Module 5 : Transducers
MODULE 1: NON-ELECTRICAL PRESSURE
MODULE 4: ELECTRICAL TEMPERATURE
Instruments Trade N2
MODULE 8: FLOW MEASUREMENT
MODULE 9: LEVEL MEASUREMENT
MODULE 1 :NUMBER SYSTEMS :
1. Conversion Decimal to binary ,
to octal ,to hexadecimal
2. Subtraction with complements –
decimal and binary complements
MODULE 2 : CODES
1. Weighted codes
Logics N2
2. Self complementing codes
3. Non weighted codes
4. Octal Codes
5. Hexadecimal code
MODULE 4 : LOGIC GATES
1. Various types
2. Combination of gates in circuits
 MODULE 5: Memory elements
1. RS flip flops
2. Clock wave
3. Clocked RS flip flop
4. Time Diagrams
5. Other types of flip flop circuits
MODULE 10: MEMORIES
1. Types of memories
2: MENSURATION
3: FACTORISATION
4: EXPONENTS & LOGARITHMS
Mathematics N2
5: EQUATIONS & MANIPULATION OF FORMULAE
6: TRIGNOMETRY
7: GRAPHS
COLD WATER SUPPLY
HOT WATER SUPPLY
Plumbing N2 DRAINAGE
STEEL PIPES DEVELOPMENT
CALCULATIONS
Welding symbols
Welding setups (TIG, MMAW, SMAW)
Welding Theory N2 Cylinders and pipe connection diagram
Rolled steel joist and T-junction diagrams
General safety
N2 • Fundamentals of Eng. Drawing, Machine symbols and Welding
Engineering Drawing • Square screw threads
• First angle orthographic projection (Sectioning)
N2 • Isometric Drawing
MODULE 3 : Gears and synchronising
Unit.
Motor Trade Teory N2
MODULE 4 : Propeller shafts,
Universal joints and drive shafts.
Building Admin N4 Module 01 –Organisational structures
 Module 02 –Departments of a Building firm
Module 03 -Site Organisation
Module 04 –Building tools and Equipment
Module 05 –Building Materials
Module 06 –Support to structures
Module 07 -Scaffolding
MODULE 1: FOUNDATIONS
MODULE 4: STEEL DOORFRAMES & WINDOWS
Building and Structural MODULE 6: ROOFS
N4
Con MODULE 7: ROOF COVERINGS
MODULE 8: GUTTERING
MODULE 3: DAMP PROOFING
MODULE 1:CHEMICAL BONDING
MODULE 2:CHEMICAL GEOMETRY
Chemistry N4
MODULE 3:ACID AND BASES
MODULE 4:DESCRIPTIVE CHEM OF HYDROGEN AND CARBON
Module 3. MATERIALS

Module 4. INDUSTRIAL CHEMICAL

Chemical Plant Operation N4 GASES PROCESSES

Module 5. ORGANICS PROCESSES

MODULE 2: NUMBER SYSTEM AND CODES

MODULE 5: THE LAW OF BOOLEAN ALGEBRA
Digital Electronics N4
MODULE 7: LOGIC FAMILIES
MODULE 8: ELEMENTARY FLIP FLOPS DEVICES
MODULE 1: CAPACITORS & TEMPERATURE COEFFICIENT
MODULE 2: DC MACHINES
Electro technics N4 MODULE 3: AC THEORY
MODULE 4: TRANSFORMERS
MODULE 5: AC MACHINES
MODULE 1: KINEMATICS
Engineering Science N4 MODULE 2: ANGULAR MOTION MODULE 3: DYNAMICS
MODULE 4: STATICS (BEAMS, SHEAR FORCE AND BENDING MOMENTS)
 MODULE 5: HYDRAULICS
HYDRAULICS PRESSES
HYDRAULIC PUMPS
MODULE 6: STRESS, STRAIN AND YOUNGS MODULUS
MODULE 1 : NETWORK THEOREMS
1. Kirchoff’s Laws
2. Superposition Theorem
3. Thevenin’s Theorem
4. Norton’s Theorem
5. Maximum Power Transfer Theorem
MODULE 3 : ELECTRONIC POWER
CONTROL
1. Semiconductor Diodes
Industrial Electronics N4
2. Characteristic curves
3. Transformer – power supply circuits and calculations
4. Diode as a rectifier.
5. Capacitor Filtering Circuits and calculations
6. LC Filtering
Advantages and disadvantages of various types of filtering discussed
MODULE 5
1. Transistor Amplifiers
2. Operational Amplifiers
Thermometers, liquid filled, gas filled, vapor filled, RTD
Level : ekstrom, sight glass, rigid arm.
Instruments N4
Pyrometers,
Pneumatic Telemetering
1. Equations
2. Limits and binomial theorem
Mathematics N4
3. Differentiation
4. Integration
• Conventional representation (Gears)
• Cams
Mechanical Draughting N4
• Sectional Drawing
• Detail drawing
 1. WORKSHOP LAYOUT
2. METAL CUTTING MACHINES
Mechanotechnics N4 3. GEAR DRIVES
4. HYDRAULIC SYSTEMS
5. BEARINGS
Module 7 and 8: Practical Project - Roof or Door
Quantity Surveying N4 Module 1 : Theory - BOQs,Abbreviations, QS Terms
Module 2 : Drawings and Sketches - Door And Roof truss.

Beams design ( Reactions, SFD, BMD, Ze)

Moment of Inertia ( Area, X & Y, Ixx and Iyy, Ze)
Building and Structural Bolted Connections
N5
Con Bending Schedule
Frames
Drawings ( Foundations, Stairs, concrete ,...)
MODULE 1:INTRODUCTION TO ORGANIC CHEMISTRY (KNOW BASICS OF ALL
HOMOLOGOUS SERIES)
*ALKENES
Chemistry N5
*ALKANES
*ALCOHOLS
*KETONES AND ALDEHYDES

Module 3. SEPARATORS, CYCLONES, MIXERS

Chemical Plant Operation N5
Module 4. INDUSTRIAL CHEMICAL PROCESS

MODULE 7,8,9: NUMBER SYSTEM

MODULE 6: K-MAPS AND CODE CONVERTERS
Digital Electronics N5
MODULE 10: PARTY LINE CIRCUITS
MODULE 11: COMPUTER ARCHITECTURE
Electro technics N5 TRANSFORMERS, MEASUREMENT OF POWER IN AC CIRCUITS
Module 2. Heat (2.6 Ways at which Heat is transferred)
Engineering Physics N5
 Module 3. LIGHT

Module 4. MAGNETISM

Industrial Electronics N5 Transducers, power supplies, transistors, operational amplifiers

Module1[Limits and Continuity] Module2[Differentiation Techniques]
Mathematics N5 Module3[Applications of Differentiation, Newton’s method, Module4[Integration
techniques]
Mechanical Design N5 COTTERED, LOZENGE & WELDED JOINT
Power machines N5 COMBUSTION OF FUELS, GASES, STEAM PLANT & AIR COMPRESSORS
Building Admin N5 Module 01-Module 07
Practical Projects : Module 3:Lean to Roof or Garden ,
Quantity Surveying N5 Module 1: Checklists, QS Terminology, SI units from SS
Module 3: Interim Valuation
Instruments N5 PH, Automatic control, flow, Conductivity

1. BELT DRIVES
MECHANOTECHNICS N5 2. REDUCTION GEAR DRIVES
3. BUCKET ELEVATORS
4. ROPE HAULAGES
5. ELEVATORS

Concrete design (All structural element)

Building and Structural
N6 Steel design ( all structural elements )
Con SANS code
Module 01 – Work study
Module 02 –Estimating
Building Administration N6
Module 03 –Pre-tendering
Module 04 –Tendering
 Module 05 –Building Laws

MODULE 1:DRYING
MODULE 2:CRYSTALLLISATION
chemical tech N6
MODULE 3: EVAPORATION
MODULE 4:HEAT TRANSFER
Module 3. INORGANIC CHEMISTRY

Module 4. PRESSURE MEASUREMENT

Chemical Plant Operation N6 Module 5. TEMPERATURE MEASUREMENT

Module 6. FLOW MEASUREMENT

Module 7. LEVEL MEASUREMENT

MODULE 1: NUMBER SYSTEM

MODULE 5 &6: HIGH LEVEL PROGRAMMING
Digital Electronics N6 MODULE 7: COMPUTER ARCHITECTURE
MODULE 9: D/A TO A/D CONVERSION
MODULE 10: COMPUTER SYSTEMS
Electrotechnics N6 TRANSFORMERS, AC MACHINES
MODULE 1:SOUND
MODULE 2: THERMODYNAMICS
Engineering Physics N6
MODULE 3:ELECTROSTATICS
MODULE 4: ATOMIC PHYSICS
Ultrasonic, X-RAYS, Radiation, Automatic inspection, electronic safety devices, power
Industrial Electronics N6
control.
MODULE 1: ANALYSERS
MODULE 2: INTRINSIC SAFETY
INSTRUMENTS N6
MODULE 3: DISTILLATION COLUMNS
MODULE 4: AUTOMATIC CONTROL
1. DIFFERENTIATION
Mathematics N6 2. INTEGRATION
3. PARTIAL FRACTIONS
 4. DIFFERENTIAL EQUATIONS
5. APPLICATION OF INTEGRATION
6. COMBINED APPLICATION OF DIFFERENTIATION AND INTEFGRATION
BELT DRIVES, BENDING&TWISITING OF SHAFTS, PULLEY&GEAR DESIGN, BEARING &
Mechanical Design N6
LUNBRICATION

1. BLOCK AND BAND BRAKES

2. LINESHAFTS
Mechanotechnics N6
3. FLY WHEELS
4. REDUCTION GEAR
5. RAIL TRACTION
Power machines N6 STEAM NOZZLES, STEAM PLANT, CYCLES, AIR COMPRESSORS
Theory : Module 1: QS Terms,SI units from SS,BOQ Principles for Preparation AND sketches
Module 3.5:Project Measurement- Reinforced Concret Piles Module and Door
Quantity Surveying N6 Module 4 : Cost Estimations Calculations