Technical Data Sheet

Approved 35982;35983 1,2 35982 epoxy mastic ^(ValidationDate) 1

Jotafix Epoxy Primer

Product description
This is a two component amine cured epoxy mastic coating. It is a surface tolerant primer designed for
application with brush and roller. Specially designed for areas where optimum surface preparation is not possible
or required. Provides protection in environments with high corrosivity. Can be used as primer, mid coat, finish
coat or as single coat system in marine atmospheric environments. Suitable for properly prepared carbon steel,
galvanised steel, stainless steel and a range of aged coating surfaces. It can be applied at sub zero surface
temperatures.

Typical use
General:
Primarily designed for smaller maintenance and repair jobs.

Marine:
Outside hulls, exterior and interior areas.
Other

Approvals and certificates

Grain, Newcastle Occupational Health

When used as part of an approved scheme, this material has the following certification:
- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5
and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO
2010 FTP Code Ch. 8
Additional certificates and approvals may be available on request.

Colours
grey, red

Product data
Property Test/Standard Description

Solids by volume ISO 3233 68 ± 2 %

Gloss level (GU 60 °) ISO 2813 semi gloss (35-70)
Flash point ISO 3679 Method 1 31 °C
Density calculated 1.5 kg/l

Region Regulation Test Standard VOC Value

US CARB(SCM)2020 / SCAQMD rule 1113 Calculated 290 g/l

Hong Kong Air Pollution Control (VOC) Regulation Calculated 290 g/l
EU European Paint Directive 2004/42/CE Calculated 290 g/l
EU IED Industrial Emission Directive 2010/75/EU Calculated 290 g/l
Korea Korea Clean Air Conservation Act Calculated 318 g/l
China GB 30981-2020 Limit of harmful GB/T 23985-2009 8.3 254 g/l
substances of industrial protective coatings

Date of issue: 15 August 2024 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafix Epoxy Primer

Film thickness per coat

Typical recommended specification range

Dry film thickness 50 - 100 μm

Wet film thickness 75 - 150 μm
Theoretical spreading rate 13.6 - 6.8 m²/l

Surface preparation

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel St 2 (ISO 8501-1) Sa 2 (ISO 8501-1)

Stainless steel The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using non-metallic
or bonded fibre machine or hand abrasive media which is suitable to
abrasive pads to impart a scratch achieve a sharp and angular surface
pattern to the surface. profile.
Galvanised steel The surface shall be clean, dry and Sweep blast-cleaning using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Shop primed steel Clean, dry and undamaged shop Sa 2 (ISO 8501-1)
primer (ISO 12944-4 5.4)
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating coating

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: Use a round brush. Care must be taken to achieve the spreading rate.
Roller: Use of a foam roller will provide the best finish results.

Date of issue: 15 August 2024 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafix Epoxy Primer

Product mixing ratio (by volume)

Jotafix Epoxy Primer Comp A 5 part(s)

Jotafix Epoxy Primer Comp B 1 part(s)

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray

Nozzle tip (inch/1000): 17 - 23
Pressure at nozzle (minimum): 150 bar / 2100 psi

Drying and Curing time

Substrate temperature -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 25 h 15 h 8h 5h 2.5 h 45 min

Walk-on-dry 48 h 40 h 20 h 12 h 6h 2h
Dry to over coat, minimum 40 h 30 h 15 h 8h 4h 1.5 h

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.

Induction time and Pot life

Paint temperature 23 °C

Pot life 2h

Date of issue: 15 August 2024 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafix Epoxy Primer

Product compatibility
Depending on the actual exposure of the coating system, various waterborne epoxy primers/intermediates can
be used in combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy shop primer, inorganic zinc silicate shop primer, zinc epoxy, epoxy
Subsequent coat: polyurethane, epoxy, acrylic

Packaging (typical)
Volume Size of containers
(litres) (litres)

Jotafix Epoxy Primer Comp A 15 20

Jotafix Epoxy Primer Comp B 3 3

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool,
well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed.
Handle with care.

Shelf life at 23 °C
Jotafix Epoxy Primer Comp A 24 month(s)
Jotafix Epoxy Primer Comp B 24 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Date of issue: 15 August 2024 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafix Epoxy Primer

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.

Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 15 August 2024 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com