Scribd
Upload
20 views

Load Schedule and Computations: Dishwasing Machine

Uploaded by

Muhammad Abdullah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
20 views

Load Schedule and Computations: Dishwasing Machine

Uploaded by

Muhammad Abdullah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

LOAD SCHEDULE AND COMPUTATIONS

Ground Floor

CKT NO. OF OUTLETS COMPUTED BREAKER


WATTS SIZE OF WIRE SIZE OF CONDUIT
NO. L.O. C.O. OTHERS AMPERE RATING
1 7 700 3.04 15 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
2 8 800 3.48 15 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
3 8 2880 12.52 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
4 REF 1000 4.35 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
5 RANGE 1500 6.52 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
6 DISHWASING
MACHINE 1500 6.52 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
7 FREEZER 400 1.74 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
8 SPARE 1500 6.52 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
9 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
10 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
11 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
12 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
13 SPARE 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE

For Circuit Number 1 and 2: Lighting Loads

“The Philippine Electrical Code provides that 100 Watts be the maximum load per light outlet.”

Circuit Number 1:
P = 7 outlets X 100 W = 700 W
I = 700/230 = 3.04 A

Circuit Number 2:
P = 8 outlets X 100 W = 800 W
I = 800/230 = 3.48 A

“The National Electrical Code provides that ampacity of the connected load shall not exceed 80%
of the amperage capacity of the conductor and the fuse.” The maximum ampacity load of a 3.5 mm 2
copper wire and 15 AT breaker are 30 A and 15 A respectively. 80% of 30 A and 15 A are 24 A and 12 A
respectively. Therefore, for Circuit Number 1 to 6, the use of 3.5 mm2 wire and 15 AT breaker is safe.

Also, for 2 pieces of 3.5 mm2 wire, use 13 mm diameter of conduit pipe.

For Circuit Number 3: Small Appliance Loads

Section 3.3.1.2 of the Philippine Electrical Code specify 180 Watts load limit per convenience
outlet. It simply mean that, each convenience outlet, is considered to have a maximum load of not less
than 180 Watts per plug or gang.

Circuit Number 3:
P = 8 outlets X 2 gangs X 100 W = 2880 W
I = 2880/230 = 12.52 A

“The National Electrical Code provides that ampacity of the connected load shall not exceed 80%
of the amperage capacity of the conductor and the fuse.” The maximum ampacity load of a 3.5 mm2
copper wire and 20 AT breaker are 30 A and 20 A respectively. 80% of 30 A and 15 A are 24 A and 16 A
respectively. Therefore, for Circuit Number 7 to 3, the use of 3.5 mm2 wire and 20 AT breaker is safe.

Also, for 2 pieces of 3.5 mm2 wire, use 13 mm diameter of conduit pipe.
For Circuit Number 4 to 8: Other Loads

Circuit Number 4: Refrigerator


P = 1000 W
I = 1000/230 = 4.35 A

Circuit Number 5: Range


P = 1500 W
I = 1500/230 = 6.52A

Circuit Number 6: DISHWASHING MACHINE


P = 1500 W
I = 1500/230 = 6.52 A

For the sizing of wire,


I = 6.52 X 125% = 8.15 A

For the sizing of breaker,


I = 6.52 X 250% = 16.30A

Circuit Number 7: FREEZER


P = 400 W
I = 400/230 = 1.74 A

For Circuit Number 9 to 13: Air-Conditioning Units

Article 6.7 of the Philippine Electrical Code provides that: “ Branch circuit conductor supplying a
motor shall have an ampacity not less than 125% of the full load current.”

Also, the code on branch circuit protection for a single motor provides that: “It shall be increased
by 250% of the full load current of the motor.”

Circuit Number 9 to 13
P = 1000 W
I = 1000/230 = 4.35 A

For the sizing of wire,


I = 4.35 X 125% = 5.43 A

For the sizing of breaker,


I = 4.35 X 250% = 10.87 A

Calculation for the Ampacity of the Sub-Feeder Conductor and the Disconnecting Means

Lighting Loads = 1500 W


Small Appliance Loads = 2880 W
Other Loads = 5900 W

Total Load (Except the Air-Conditioning Units) = 10280W

For the first 10000 W at 100% DF = 10000 W

Subtract: 10280 – 10000 = 280 W

For the remaining load, apply 40% DF


280 X 40% = 112 W
Air-Conditioning Units at 100% DF
5 units X 1000 W X 100% = 5000 W

Total = 15112 W

Total Connected Load plus 25% of the Largest Motor

I = (15112 W + 25% of 1500w)/230 = 67.33 A

Sub-Feeder:
Overcurrent Protection: Use 90 AT Breaker
Size of Wire: Use 2 – 30.0 mm2 THW conductor with 25 mm ф Rigid Steel Conduit

Second Floor

CKT NO. OF OUTLETS COMPUTED BREAKER


WATTS SIZE OF WIRE SIZE OF CONDUIT
NO. L.O. C.O. OTHERS AMPERE RATING
1 11 1100 4.78 15 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
2 10 1000 4.35 15 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
3 8 2880 12.52 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
4 REF 1000 4.35 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
5 RANGE 1500 6.52 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
6 DISHWASING
MACHINE 1500 6.52 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
7 FREEZER 400 1.74 20 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
8 SPARE 1500 6.52 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
9 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
10 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
11 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
12 ACU 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE
13 SPARE 1000 4.35 30 AT 2 – 3.5 mm2 TW 13 mm ф PVC PIPE

For Circuit Number 1 and 2: Lighting Loads

“The Philippine Electrical Code provides that 100 Watts be the maximum load per light outlet.”

Circuit Number 1:
P = 11 outlets X 100 W = 1100 W
I = 1100/230 = 4.78 A

Circuit Number 2:
P = 10 outlets X 100 W = 1000 W
I = 1000/230 = 4.35 A

For Circuit Number 3: Small Appliance Loads

Circuit Number 3:
P = 8 outlets X 2 gangs X 100 W = 2880 W
I = 2880/230 = 12.52 A

.
For Circuit Number 4 to 8: Other Loads

Circuit Number 4: Refrigerator


P = 1000 W
I = 1000/230 = 4.35 A
Circuit Number 5: Range
P = 1500 W
I = 1500/230 = 6.52A

Circuit Number 6: DISHWASHING MACHINE


P = 1500 W
I = 1500/230 = 6.52 A

For the sizing of wire,


I = 6.52 X 125% = 8.15 A

For the sizing of breaker,


I = 6.52 X 250% = 16.30A

Circuit Number 7: FREEZER


P = 400 W
I = 400/230 = 1.74 A

For Circuit Number 9 to 13: Air-Conditioning Units

Circuit Number 9 to 13
P = 1000 W
I = 1000/230 = 4.35 A

For the sizing of wire,


I = 4.35 X 125% = 5.43 A

For the sizing of breaker,


I = 4.35 X 250% = 10.87 A

Calculation for the Ampacity of the Sub-Feeder Conductor and the Disconnecting Means

Lighting Loads = 2100 W


Small Appliance Loads = 2880 W
Other Loads = 5900 W

Total Load (Except the Air-Conditioning Units) = 10880W

For the first 10000 W at 100% DF = 10000 W

Subtract: 10280 – 10000 = 880 W

For the remaining load, apply 40% DF


880 X 40% = 352 W

Air-Conditioning Units at 100% DF


5 units X 1000 W X 100% = 5000 W

Total = 15352 W

Total Connected Load plus 25% of the Largest Motor

I = (15352 W + 25% of 1500w)/230 = 68.39 A


Sub-Feeder:
Overcurrent Protection: Use 90 AT Breaker
Size of Wire: Use 2 – 30.0 mm2 THW conductor with 25 mm ф Rigid Steel Conduit

Calculation for the Ampacity of the Service Entrance Conductor and the Main Disconnecting Means

Lighting Loads = 3600 W


Small Appliance Loads = 5760 W
Other Loads = 11800 W

Total Load (Except the Air-Conditioning Units) = 21160 W

For the first 10000 W at 100% DF = 10000 W

Subtract: 21160 – 10000 = 11160 W

For the remaining load, apply 40% DF


11160 X 40% = 4464 W

Air-Conditioning Units at 100% DF


10 units X 1000 W X 100% = 10000 W

Total = 24464 W

Total Connected Load plus 25% of the Largest Motor

I = (24464 W + 25% of 1500w)/230 = 108 A

Service Entrance:
Overcurrent Protection: Use 150 AT Breaker
Size of Wire: Use 2 – 50.0 mm2 THW conductor with 32 mm ф Rigid Steel Conduit
ONE LINE DIAGRAM

SYMBOLS
ELECTRICAL SPECIFICATIONS

1. THE ELECTRICAL INSTALLATION SHALL BE DONE IN ACCORDANCE WITH THE APPROVED PLANS
AND UNDER DIRECT SUPERVISION AND CONTROL OF A LICENSED PROFESSIONAL ELECTRICAL
ENGINEER OR MASTER ELECTRICIAN.

2. THE ELECTRICAL INSTALLATION SHOWN ON THE PLANS SHALL BE CONFORM WITH THE LATEST
EDITION OF THE PHILIPPINE ELECTRICAL CODE, RULES AND REGULATIONS OF THE COMPANY AND
THE LOCAL GOVERNMENT.

3. ALL ELECTRICAL MATERIALS AND EQUIPMENT TO BE USED IN THIS PROJECT SHALL BE BRAND-
NEW AND OF APPROVED QUALITY AND BRAND.

4. THE WIRES TO BE USED SHALL NOT BE SMALLER THAN 3.5 mm2 TW, WITH 600 V INSULATION.

5. THE TYPE OF POWER SERVICE TO BE SUPPLIED SHALL BE SINGLE PHASE, 230 V AC.

You might also like