EDS-G4012 Series

Quick Installation Guide

Moxa EtherDevice™ Switch

Version 1.1, November 2022

Technical Support Contact Information

www.moxa.com/support

 2022 Moxa Inc. All rights reserved.

P/N: 1802040120111
*1802040120111*
Package Checklist
The EDS-G4012 Series industrial DIN-rail EtherDevice Switch (EDS) is
shipped with the following items. If any of these items are missing or
damaged, please contact your customer service representative for
assistance.
• 1 EDS-G4012 Ethernet switch
• Quick installation guide (printed)
• Warranty card
• Substance disclosure table
• Product certificate of quality inspection (Simplified Chinese)
• Product notices (Simplified Chinese)

NOTE You can find information and software downloads on the

relevant product pages located on Moxa’s website:
www.moxa.com

Default Settings
• IP address: 192.168.127.253
• Subnet Mask: 255.255.255.0
• Username: admin
• Password: moxa

Panel Views of EDS-G4012 Series

Front Panel View

1. 1000BaseT(X) LED indicator 8. LED indicators: STATE (S),
2. 10/100BaseT(X) LED FAULT (F), PWR1 (P1), PWR2
indicator (P2), MSTR/HEAD (M/H),
3. 10/100/1000BaseT(X) ports, CPLR/TAIL (C/T), SYNC
Port 1 to 8 9. Console port (RJ45, RS-232)
4. 10/100/1000BaseT(X) or 10. USB storage port (type A,
100/1000BaseSFP combo currently disabled)
ports, Port G1 to G4 11. Model name

-2-
5. 100/1000BaseSFP LED 12. 100/1000/2500BaseSFP port,
indicator QG1 to QG4
6. Grounding connector screw 13. SmartPoE LED indicator of PoE
7. Terminal blocks for power ports
input, digital input, and relay 14. 1000/2500BaseSFP LED
output indicator
Bottom Panel View
1. microSD card slot
(currently disabled)
2. Reset button
3. DIP switches for
Turbo Ring, Ring
Master, and Ring
Coupler

Mounting Dimensions

-3-
DIN-rail Mounting
The DIN-rail mounting kit is fixed to the back panel of the EDS device
when you take it out of the box. Mount the EDS device on corrosion-
free mounting rails that meet the EN 60715 standard.
Installation
STEP 1—Insert the upper lip of
the DIN rail into the DIN-rail
mounting kit.
STEP 2—Press the EDS device
towards the DIN rail until it
snaps into place.

Removal
STEP 1—Pull down the latch on
the mounting kit with a
screwdriver.
STEP 2 & 3—Slightly pull the
EDS device forward and lift up
to remove it from the DIN rail.

NOTE Our DIN rail kit now utilizes a quick release mechanism to make
it easier for users to remove the DIN rail from the EDS device.

-4-
Wall Mounting (Optional)
For some applications, you will find it convenient to mount the Moxa
EDS device on a wall, as shown in the following illustrations:
STEP 1—Remove the DIN-rail
attachment plate from the rear
panel of the EDS device, and then
attach the wall mount plates with
M3 screws.

STEP 2—Mounting the EDS device on a wall

requires four screws. Use the EDS device, with wall
mount plates attached. The heads of the screws
should be less than 6.0 mm in diameter, and the
shafts should be less than 3.5 mm in diameter, as
shown in the figure on at right.

NOTE Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting
Plates.

NOTE Do not screw the screws in all the way—leave about 2 mm to

allow room for sliding the wall mount panel between the wall
and the screws.

STEP 3—Once the screws are

fixed to the wall, insert the
four screw heads through the
wide parts of the keyhole-
shaped apertures, and then
slide the EDS device
downwards, as indicated in
the figure at the right.
Tighten the four screws for
more stability.

Wiring Requirements

ATTENTION
Safety First!
External metal parts are hot. Take the necessary precautions if
you are required to handle the device.

-5-
 ATTENTION
In order to ensure reliable operations, please make sure the
operating temperature of the environment does not exceed the
specifications. When mounting an EDS device with other
operating units in a cabinet without forced ventilation, a
minimum of 4 cm space on both the left and right of the switch
is recommended.

ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your EDS device. Calculate the maximum possible
current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for
each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your
equipment.

Be sure to read and follow these important points below:

• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.

NOTE Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires
with different signal characteristics should be routed separately.

• You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb
is that wiring that shares similar electrical characteristics can be
bundled together.
• You should separate input wiring from output wiring.
• We advise that you label the wiring to all devices in your system.

Grounding the Moxa EDS Series

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw (M4) to the grounding surface prior to connecting
devices.

NOTE The grounding wire should have a minimum diameter of

1.5 mm2.

ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.

-6-
Suggested Wire Type for Wiring Relay Contact

(R), Digital Input (DI), and Power Inputs (P1/P2)

The EDS device includes two 4-pins 3.5 mm pin-pitch terminal blocks.
When wiring the relay contact (R), digital input (DI), and power inputs
(P1/P2) for the EDS device, we suggest using the cable type – AWG 18-
24 and the corresponding pin type cable terminals.

NOTE The wire must be able to withstand at least 105°C and the
torque value should be 4.5 lb-in (0.51 N-m).

NOTE We suggest the length of the pin type cable terminal is 8 mm.
In order to tighten the wire properly, ① use a small flathead
screwdriver to press the push-in button beside each terminal of
the terminal block connector before and during ② inserting the
wire. ③ Release the screwdriver after the wire has been fully
inserted. Please refer to the diagram below.

Wiring the Relay Contact

The EDS device has one set of relay output. This relay contact uses two
contacts of the terminal block on the EDS’s power module. Refer to the
section for detailed instructions on how to connect the wires to the
terminal block connector, and how to attach the terminal block
connector to the terminal block receptor.

-7-
 Relay:
The two contacts of the 4-pin terminal
block connector are used to detect
user-configured events. The two wires
attached to the relay contact form an
open circuit when a user-configured
event is triggered or there is no power
supply to the switch. If a user-
configured event does not occur, the
relay circuit remains closed.

Wiring the Redundant Power Inputs

The EDS device includes both high-voltage and low-voltage products.
For the low-voltage (LV models) products, there are two power inputs
for redundancy; for the high-voltage (HV models) products, there is
only one power input. Refer to the instructions and diagram below on
how to connect the wires to the terminal block connector on the
receptor.

STEP 1: Insert the Positive/Negative

DC or Line/Neutral AC wires into the
V+/V- or L/N terminals, respectively.
STEP 2: To keep the DC or AC wires
from pulling loose, use a small flat-
blade screwdriver to tighten the wire-
clamp button on the front of the
terminal block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS devices’ right side.

-8-
Wiring the Digital Inputs
The EDS device has one set of digital input (DI). The DI consists of two
contacts of the 4-pin terminal block connector on the EDS's right-side
panel. Refer to the instructions and diagram below on how to connect
the wires to the terminal block connector on the receptor.

STEP 1: Insert the negative

(ground)/positive DI wires into the
┴/I terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp
button on the front of the terminal
block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS devices’ right side.

Rotating the Power Module

The power module for the EDS device can be rotated to make it easier
to fit your field site application.
Step 1: Remove the two screws that fasten the power module to the
EDS device and remove the module.
Step 2: Turn the power module clockwise so that the power, digital
input, and relay output connectors can be moved upwards.
Step 3: Replace the module back on to the EDS device.
Step 4: Fasten two screws on to the module.

-9-
Communication Connections
Each EDS-G4012 Series switch has various types of communication
ports:
• RJ45 console port (RS-232 interface)
• USB storage port (type A connector, currently disabled)
• 10/100/1000BaseT(X) Ethernet ports
• 10/100/1000BaseT(X) or 100/1000BaseSFP combo ports
• 1000/2500BaseSFP slots
• microSD card slot (currently disabled)

Console Port Connection

The EDS device has one RJ45 console port (RS-232), located on the
front panel. Use either an RJ45-to-DB9 (see the cable following wiring
diagrams) to connect the EDS’s console port to your PC’s COM port.
You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the EDS that has a baud rate of 115200.
RJ45 Console Port Pinouts

Pin Description
1 DSR
2 RTS
3 –
4 TxD
5 RxD
6 GND
7 CTS
8 DTR

USB Connection

NOTE The USB function is currently reserved and may be required in

the future. It should be noted that this port cannot be used for
charging any devices.

10/100/1000BaseT(X) Ethernet Port Connection

1000BaseT(X) data is transmitted on differential TRD+/- signal pairs

over copper wires.
MDI/MDI-X Port Pinouts

Pin Signal
1 TRD(0)+
2 TRD(0)-
3 TRD(1)+
4 TRD(2)+
5 TRD(2)-
6 TRD(1)-
7 TRD(3)+
8 TRD(3)-

- 10 -
100/1000BaseSFP and 1000/2500BaseSFP (mini-GBIC)

Fiber Port

The fiber ports on the switch are 100/1000BaseSFP and

1000/2500BaseSFP fiber ports, which require 100M, 1G, or 2.5G mini-
GBIC fiber transceivers to work properly.
The concept behind the LC port and cable is quite straightforward.
Suppose that you are connecting devices I and II; contrary to electrical
signals, optical signals do not require a circuit in order to transmit data.
Consequently, one of the optical lines is used to transmit data from
device I to device II, and the other optical line is used transmit data
from device II to device I, for full-duplex transmission.
Remember to connect the Tx (transmit) port of device I to the Rx
(receive) port of device II, and the Rx (receive) port of device I to the
Tx (transmit) port of device II. If you make your own cable, we suggest
labeling the two sides of the same line with the same letter (A-to-A and
B-to-B, as shown below, or A1-to-A2 and B1-to-B2).
LC-Port Pinouts LC-Port to LC-Port Cable Wiring

ATTENTION
This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.

Reset Button
The reset button can perform two functions. One is to reset the
Ethernet switch to factory default settings by pressing and holding the
reset button for longer than five seconds. Use a pointed object, such as
a straightened paper clip or toothpick, to depress the reset button. This
will cause the STATE LED to blink once a second. After depressing the
button for 5 continuous seconds, the STATE LED will start to blink at 4
times/sec. This indicates that factory default settings have been loaded
and you can release the reset button. The other function is to reboot
the device by depressing reset button for less than five seconds.

Turbo Ring DIP Switch Settings

The EDS devices are plug-and-play managed redundant Ethernet
switches. The proprietary Turbo Ring protocol was developed by Moxa
to provide better network reliability and faster recovery time. Moxa
Turbo Ring’s recovery time is less than 50 ms (Turbo Ring V2) —
compared to a 3- to 5-minute recovery time for commercial switches—
decreasing the possible loss caused by network failures in an industrial
setting.

- 11 -
There are five Hardware DIP Switches for Turbo Ring on the bottom
panel of the EDS device that can help setup the Turbo Ring easily
within seconds. If you do not want to use a hardware DIP switch to
setup the Turbo Ring, you can use a web browser, telnet, or console to
disable this function.

NOTE Please refer to the Turbo Ring section in User's Manual for
more detail information about the setting and usage of Turbo
Ring V2.

Turbo Ring DIP Switch Settings

The default setting for each DIP Switch is OFF. The

following table explains the effect of setting the DIP
Switch to the ON position.
Remove the rubber cover on the bottom panel of
the device to expose the DIP switches.

DIP Switch Settings

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5

ON: Enables the ON: Enables ON: ON: Activates
default “Ring this EDS as Enables the DIP switch 2,
Coupling the Ring default 3, and 4 to
(backup)” port Master. “Ring configure
when DIP switch Coupling” Turbo Ring V2
4 is already port. settings.
Reserved
enabled.
for future
OFF: Enables the OFF: This OFF: This OFF: DIP
use
default Ring EDS will not EDS will not switch 2, 3,
Coupling be the Ring be the Ring and 4 will be
(primary) port Master. Coupler. disabled.
when DIP switch
4 is already
enabled.

NOTE You must enable the Turbo Ring (DIP switch 5) first before
using the DIP switch to activate the Master and Coupler
functions.

NOTE If you do not enable any of the EDS switches to be the Ring
Master, the Turbo Ring protocol will automatically choose the
EDS switch with the smallest MAC address range to be the Ring
Master. If you accidentally enable more than one switch to be
the Ring Master, these switches will auto-negotiate to
determine which one will be the Ring Master.

LED Indicators
The front panel of the Moxa EDS-G4012 Series contains several LED
indicators. The function of each LED is described in the following table:

- 12 -
Device LED Indicators

LED Color State Description

When system has passed power-
On on self-test (POST) and is ready
to run.
Press the reset button for five
Blinking
seconds to reset to factory
Green (1 time/sec)
default settings
When pressing the reset button
STATE Blinking
depress for 5 seconds to reset to
(4 times/sec)
factory default.
Off N/A
The system has initially failed the
boot-up process
Red On
• System Info. Read Fail or
EEPROM information error
1. The relay contact has been
triggered
2. The ingress rate limit has
On
been exceeded and the port
FAULT Red has entered shut down mode
3. Invalid Ring port connection
When the system boots up and
Off runs correctly or a user-
configured event is not triggered.
Power is being supplied to power
On
input PWR.
P1 Amber
Power is not being supplied to
Off
power input PWR.
Power is being supplied to power
On
input PWR.
P2 Amber
Power is not being supplied to
Off
power input PWR.
When the switch is
On Master/Head/Root of Turbo
Ring/Turbo Chain/Fast RSTP.
1. The switch has become the
Master of Turbo Ring after
Turbo Ring has gone down
2. The switch is set as Head of
Turbo Chain and Turbo Chain
has gone down
MSTR/
Blinking 3. The switch is set as the
HEAD Green
(4 times/sec) Turbo Ring’s Member and the
(M/H)
corresponding Ring port is
down
4. The switch is set as the
Turbo Chain’s Member/ Tail
and the corresponding Head-
end Chain port is down.
When the switch is not the
Off Master/Head/Root of this Turbo
Ring/ Turbo Chain/Fast RSTP.

- 13 -
 LED Color State Description
1. The switch’s ring coupling or
dual homing function is
On enabled.
2. The switch is set as the Tail
of Turbo Chain.
1. The switch is set as the Tail
of Turbo Chain and the Chain
CPLR/
Green has gone down.
TAIL Blinking
2. The switch is set as the
(4 times/sec)
Turbo Chain’s Member/ Head
and the corresponding Tail-
end Chain port is down.
When the switch disables the
Off coupling or tail role of Turbo
Chain.
System
Green + The switch is being
LED Blinking
Amber + discovered/located by the locator
(Except (2 times/sec)
Red function.
PWR)
System
Green + Rotate The switch is importing/exporting
LED
Amber + On -> Off a file via ABC-02-USB or SD card.
(Except
Red Sequentially (currently disabled)
PWR)

Smart PoE LED Indicators

LED Color StateDescription

When the port is connected to
IEEE 802.3bt powered device
and powered at:
On • Single signature (PD) Class
5 to 8
• Dual signature (PD) Class 1
Green to 5
1. When the power is not
being supplied to a powered
device (PD)
Off
2. The port is not connected to
Smart an IEEE 802.3bt powered
PoE+ LED device
Indicators When the port is connected to
IEEE 802.3af/at powered device
On
and powered at:
• Single signature (PD) 0 to 4
The PoE power supply has been
Blinking
shut off because of low power
Amber (4 times/sec)
budget.
1. Power is not being supplied
to the powered device (PD)
Off 2. The port is not connected to
an IEEE 802.3af/at standard
PD

- 14 -
 LED Color State Description
Powered device (PD) detection
On
failure
Red Blinking Overcurrent has occurred on the
(4 times/sec) powered Device (PD)
Off PoE is operating normally

Ports LED Indicators

LED Color State Description

When the port is active and
10M/ On
links at 1000Mbps.
100M/
Blinking When the port’s data is being
1000M Green
(4 times/sec) transmitted at 1000Mbps.
Copper
When the port is inactive or link
top LED Off
down.
10M/ When the port is active and
On
100M/ links at 10/100Mbps.
1000M Blinking When the port’s data is being
Amber
Copper (4 times/sec) transmitted at 10/100Mbps.
bottom When the port is inactive or link
Off
LED down.
When the port is active and
On
links at 1000Mbps.
Blinking When the port’s data is being
Green
(4 times/sec) transmitted at 1000Mbps.
When the port is inactive or link
100M/ Off
down.
1000M
When the port is active and
(SFP port) On
links at 100Mbps.
Blinking When the port’s data is being
Amber
(4 times/sec) transmitted at 100Mbps.
When the port is inactive or link
Off
down.
When the port is active and
On
links at 2500Mbps.
Blinking When the port’s data is being
Green
(4 times/sec) transmitted at 2500Mbps.
When the port is inactive or link
1000M/ Off
down.
2500M
When the port is active and
(SFP port) On
links at 1000M.
Blinking When the port’s data is being
Amber
(4 times/sec) transmitted at 1000M.
When the port is inactive or link
Off
down.

Specifications
Interface
RJ45 Ports 10/100/1000BaseT(X)
Fiber Ports EDS-G4012-4GC: 100/1000BaseSFP
EDS-G4012-8P-4QGS: 1000/2500BaseSFP
Console Port RS-232 (RJ45)
Button Reset button

- 15 -
LED Indicators STATE (S), FAULT (F), PWR1 (P1), PWR2 (P2),
MSTR/HEAD (M/H), CPLR/TAIL (C/T), SYNC
Alarm Contact 1 normally open electromagnetic relay output with
current carrying capacity of 1 A @ 24 VDC
Digital Input 1 isolated digital input:
+13 to +30V for state “1”
-30 to +3V for state “0”
Max. input current: 8 mA
PoE
CAUTION: When it is necessary to connect the PoE ports of a Power
Bypass (-LVA) model to a Power Boost (-LVB) model within the same
system, do not use the same power supply to power both models.
Total Power Budget Power Bypass (-LVA model): 240 W @ 48 VDC
power input
Power Boost (-LVB model): 62 W @ 12 VDC, 150
W @ 24 VDC (120 W for -T model), 180 W @ 48
VDC
PoE Output Voltage 55 VDC
PoE Output Power 15.4 W for the 802.3af standard, 30 W for the
802.3at standard, 36 W in high power mode, 60 W
in 802.3bt standard
PoE Output Current 350 mA for the 802.3af standard, 600 mA for the
802.3at standard, 1960 mA for the 802.3bt
standard
Overload Current Present
Protection at Port
PoE Pinout Mode A: Pair 1,2 (V+); Pair 3,6 (V-)
Mode B: pair 4,5 (V+); pair 7,8 (V-)
Power
Pre-installed Power -LV/-LV-T models: PWR-100–LV
Module -HV/-HV-T models: PWR-105-HV-I
-LVA/-LVA-T models: PWR-101-LV-BP-I
-LVB/-LVB-T models: PWR-103-LV-VB-I
Note The EDS-G4012 Series supports modular power
supplies. The model names and power parameters
are determined by the installed power module.
For example:
EDS-G4012-T + PWR-100-LV = EDS-G4012-LV-T
EDS-G4012-T + PWR-105-HV-I = EDS-G4012-HV-
T
If you install a different power module, refer to the
specifications of the corresponding model. For
example, if you replace the power module of the
EDS-G4012-LV-T with the PWR-105-HV-I, refer to
the specifications of the EDS-G4012-HV-T.
Rated Voltage -LV/-LV-T models: 12/24/48 VDC, redundant dual
inputs
-HV/-HV-T models: 110/220 VDC/VAC, single input
-LVA/-LVA-T models: 48 VDC, redundant dual
inputs
-LVB/-LVB-T models: 12/24/48 VDC, redundant
dual inputs

- 16 -
Operating Voltage -LV/-LV-T models: 9.6 to 60 VDC
-HV/-HV-T models: 88 to 300 VDC, 85 to 264 VAC
-LVA/-LVA-T models: 44 to 57 VDC (>52 VDC for
PoE+ output recommended)
-LVB/-LVB-T models: 12 to 57 VDC (>52 VDC for
PoE+ output recommended)
Rated Current -LV/-LV-T models: 12-48 VDC, 1.50-0.40 A or 24
VDC, 0.70 A
-HV/-HV-T models: 110-220 VAC, 50-60 Hz, 0.30-
0.20 A or 110-220 VDC, 0.30-0.20 A
-LVA/-LVA-T models: 48 VDC, 5.42 A
-LVB/-LVB-T models: 12/48 VDC, 7.46/4.27 A or
24 VDC, 7.26 A
Power Consumption EDS-G4012-4GC-LV(-T) models: 12.68 W
EDS-G4012-4GC-HV(-T) models: 15.8 W
EDS-G4012-8P-4QGS-LVA(-T) models:
Without PoE: 15.58 W
With PoE: Max. 240 W for total PD power
consumption @ 48 VDC input
EDS-G4012-8P-4QGS-LVB(-T) models:
Without PoE: 17.96 W
With PoE: Max. 180 W for total PD power
consumption @ 48 VDC input;
Max. 150 W for total PD power
consumption @ 24 VDC input;
Max. 62 W for total PD power
consumption @ 12 VDC input
Inrush Current Max. 0.8 A @ 48 VDC (0.1 – 1 ms) (Applies to -LV
models)
Overload Current Present
Protection at Input
Reverse Polarity Present
Protection
Connection 2 removable 4-contact terminal blocks
Physical Characteristics
Housing Metal, IP40 protection
Dimension 55 x 140 x 122.5 mm (2.17 x 5.51 x 4.82 in)
Weight EDS-G4012-4GC (-T) models: 881.5 g (1.94 lb)
EDS-G4012-8P-4QGS (-T) models: 972 g (2.14 lb)
Installation DIN-rail mounting, wall mounting (with optional
kit)
Environmental Limits
Operating -10 to 60°C (14 to 140°F) for standard models
Temperature -40 to 75°C (-40 to 167°F) for -T models
Storage -40 to 85°C (-40 to 185°F)
Temperature
Ambient Relative 5 to 95% (non-condensing)
Humidity
Altitude Up to 2000 m
Note: Please contact Moxa if you require products
guaranteed to function properly at higher altitude.
Regulatory Approvals
Industrial IEC 62443-4-1, IEC 62443-4-2
Cybersecurity
Safety UL 61010-2-201, EN 62368-1(LVD)

- 17 -
EMC EN 55032/35, EN 61000-6-2/6-4
EMI FCC Part 15 Subpart B Class A
EMS EN 61000-4-2 (ESD) Level 4
EN 61000-4-3 (RS) Level 3
EN 61000-4-4 (EFT) Level 4
EN 61000-4-5 (Surge) Level 4
EN 61000-4-6 (CS) Level 3
EN 61000-4-8 Level 4
Shock IEC 60068-2-27
Free Fall IEC 60068-2-32
Vibration IEC 60068-2-6
Hazardous Location Class I Division 2, ATEX, IECEx
Rail Traffic EN 50121-4
(Wayside)
Traffic Control NEMA TS2
Warranty
Warranty 5 years

ATTENTION
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received
including interference that may cause undesired operation.

Hazardous Location Information (except for PoE

and HV models)
ATEX
information

II 3G Ex ec nC IIC T4 Gc
UL 22 ATEX 2741X
Ambient Range: -40°C ≤ Tamb ≤ +75°C for -T models
Ambient Range: -10°C ≤ Tamb ≤ +60°C for models
without “-T”
Rated Cable Temp. ≥ 90.4°C
WARNING-DO NOT SEPARATE WHEN ENERGIZED
IECEx IECEx UL 22.0031X
Certificate no.
Address of No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004,
manufacturer Taiwan

- 18 -
 WARNING – EXPLOSION HAZARD
Do not disconnect this equipment unless the power source has
been removed or turned off, or the installation location is
known to be non-hazardous.

Standards and Certifications

Hazardous Location IEC 60079-0, Edition 7

IEC 60079-7, Edition 5.1
IEC 60079-15, Edition 5
EN IEC 60079-0:2018
EN IEC 60079-7:2015+A1:2018
EN IEC 60079-15:2019

Specific Condition of Use

• The equipment shall only be used in an area of at least pollution

degree 2, as defined in IEC/EN 60664-1.
• The equipment shall be installed in an enclosure that provides a
minimum ingress protection of IP 54 in accordance with IEC/EN
60079-0 and accessible only by use of a tool.

- 19 -