TECHNICAL DATASHEET version 2.0., date: 20. 8.

2024

MODEL : Etrel INCH DUO

CHARGER POWER SUPPLY INFORMATION

NOMINAL VOLTAGE 360–440 V AC (three-phase)
NOMINAL CURRENT PER PHASE Max 64 A per phase (power supply of two sockets)
Three phase model 3 x 64 A.
Can be adjusted through charging station settings.

MAXIMUM CHARGING POWER 2 x 22.1 kW (three phase)

Max power can be adjusted (lowered) when the charging station is installed and later using the power
management algorithms and power management settings using the user interface (mobile app, web app).

FREQUENCY 47 Hz – 63 Hz
SUPPORTED GROUNDING SYSTEMS The charging station must be properly grounded.
Following grounding system are supported: TN-S, TN-C, TN-C-S and TT under special conditions. Where this is
possible local grounding should be done. IT grounding system supported only with use of transformer.

STANDBY OWN ENERGY CONSUMPTION Own consumption power from 5 W.

Depends on actual configuration and integrated modules (Wi-Fi, LTE, payment terminal, etc).

DEVICE OVERVOLTAGE SENSITIVITY Overvoltage category III (EN 60664).

CHARGER OUTPUT
NUMBER OF CHARGING OUTPUTS (SOCKETS) 2
NOMINAL VOLTAGE (SINGLE-PHASE VEHICLE CONNECTED) Power supply voltage 230 V AC (-10 % , +10 %) and 120 V AC (-10 %, +10 %)
PER CONNECTOR On-board car charger nominal voltage depends on the car specification and typically reaches values between
100 V dc and 500 V dc.

NOMINAL VOLTAGE (THREE-PHASE VEHICLE CONNECTED) Power supply voltage 400 V AC (-10 %, +10 %) and 208 V AC (-10 %, +10 %)
PER CONNECTOR On-board car charger nominal voltage depends on the car specification and typically reaches values between
Electrical specification

100 V dc and 500 V dc. On a three phase charging station single and three phase vehicles can charge.

NOMINAL CURRENT PER PHASE PER CONNECTOR Max 32 A per phase (for each of two sockets)
Three phase model 3 x 32A.
Can be adjusted through charging station settings.

MAXIMUM CHARGING POWER PER CONNECTOR 22.1 kW, for each of two sockets
Max. power can be adjusted (lowered) when the charging station is installed and later using the power
management algorithms and power management settings using the user interface (mobile app, web app).

CHARGING SOCKET TYPE Two Type 2 sockets compliant with IEC 62196-2
• Sockets without status LED light (default).
• Sockets with status LED light (optionally).
• Sockets with shutter (optionally).

ELECTRICAL PROTECTION
DIFFERENTIAL PROTECTION Two residual current devices with Δ I = 30 mA.
Different options possible:
• DC fault current sensor 6 mA, default option.
• RCD Type A, RCD Type A EV, RCD Type B, optionally. ●
Compliant with the following standards:
• IEC 61851, IEC 62955, IEC/EN 62423 (Type B).
SURGE AND OVERVOLTAGE PROTECTION Installed in external electrical cabinet or in charging
Optional
station.
OVERCURRENT PROTECTION One main miniature circuit breaker (MCB) 80 A, two MCB's
40 A and MCB 6 A for electronics. All MCB's have tripping
characteristics C. ●
Rated short time withstand current: 10 kA.

ADDITIONAL PROTECTION, CHECKING IF MEASURED Software overcurrent protection based on additional

CHARGING CURRENT IS HIGHER THAN SET CURRENT internal current measurements.
Prevents circuit breaker outage. Stop charging if load (EV) does not follow ●
current’s setpoint.
 METERING
MID METER Two MID meters are installed inside the charging station.
Accuracy meter rating: Class 1 for active energy
according to EN 62053-21 and class B according to EN ●
50470-3.

EMBEDDED METER Embedded meter accuracy rating: 2 %.

Possible measurements: active and reactive energy and power on all phases,
voltage measurements on all phases, current on all phases and energy in both Optional
directions, power factor, frequency.
• When MID meter is installed part of embedded meter is removed.

COMMUNICATION INTERFACES WITH SMART HOME OR CPO BACK-END

ETHERNET Ethernet module
10M/100M connection available in the charger service area. ●
MOBILE LTE module
Modem supports following frequencies:
• GSM | GPRS | EDGE: 850, 900, 1800, 1900.
• UMTS | HSPA; 800/850, 900, AWS 1700, 1900, 2100 MHz.
• Bands B6 and B19 (800 MHz) are a subset of B5 (850 MHz) and are
supported as well.
• Installation of LTE module cancels the possibility of the Wi-Fi module.
ROUTER LTE Router
Mobile: 4G (LTE) – Cat 4 DL up to 150 Mbps, UL up to 50 Mbps; DC-HSPA+;
UMTS; TD-SCDMA; EDGE; GPRS. Optional
Ethernet: 2 x 10/100 Ethernet ports: 1 x WAN (configurable as LAN), 1 x LAN.
NETWORK SWITCH Ethernet switch
Supports straight or cross wired cables.
Operating mode: Store and Forward, L2 wire-speed/non-blocking switching
engine.
Speed: 10/100 Mbps.
Protocols: IEEE 802.3 , IEEE 802.3x, Flow Control, Back Pressure, TCP/UDP.
DIGITAL INPUTS AND OUTPUTS Signal 12 V, configurable digital inputs and outputs.

COMMUNICATION INTERFACES WITH ELECTRIC VEHICLES

IEC 61851 Digital communication according to IEC 61851-1:2017 is
supported. ●
Communication

• Older versions of the standard are also supported.

COMMUNICATION PROTOCOLS
OCPP • OCPP 1.6 SOAP (fully supported).
• OCPP 1.6 JSON (all messages /methods supported).
• OCPP 2.0 JSON (upcoming).
• Additionally: Custom data transfer messages supported (for pricing and on display advertising).
• Allows OCPP communication with multiple nodes.

CUSTOM WEB API We can provide API specification.

• Authorization is supported/required on this interface.

MODBUS TCP SERVER Used for integration with Smart Home/Smart building.
• Modbus registers table can be provided.

USER INTERFACES
TRUE COLOR LCD DISPLAY WITH TOUCH INTERFACE Specifications:
• LCD visual dimensions: 118.5 x 77.6 mm.
• Resolution: 800 x 480 pixels.
• 5-inch touch display true color (16 MB RGB).
●
• Sunlight readable, 12 o'clock view angle.

WEB INTERFACE FOR LOCAL USERS AND MAINTENANCE Embedded web interface with responsive design (PC,
tablet, phone).
It allows charger configuration, online control of charging session, enables ●
reporting, diagnostics/trouble shooting and firmware upgrades.

STATUS LED Is turned on in standby mode to indicate charger present

status. ●
OTHER USER INTERFACE FUNCTIONALITIES
HELP EMBEDDED ON SCREEN Charging station's LCD provides help tips. ●
MULTILINGUAL SUPPORT Multiple languages supported.
Configurable through web interface. ●
ON SCREEN ADVERTISING Advertisement can be shown on the user interface. Optional
OTHER Remote charging start/stop, reservations, configurations, interactive charging levels
(user, building, other charging stations, grid), updating, clustering …
 CHARGER UNLOCKING POSSIBILITIES
RFID READER RFID module specification:
• Supports SPI and UART, 4 GPIO's.
• Integrated antenna, frequency 13.56 MHz.
• Up to 7 cm reading distance.
Supported cards:
- ISO14443A: MIFARE Classic 1k & 4k, MIFARE Classic 1k & 4k EV14), Mini,
DESFire EV13), Plus S&X, Pro X, SmartMX, Ultralight, Ultralight EV14), Ultralight
C, NTAG2xx
4)

- SLE44R35, SLE66Rxx (my-d move), LEGIC Advant1), PayPass2)

●
2) 2) 2) 2)
- ISO14443B: Calypso , CEPAS , Moneo , PicoPass , SRI512, SRT512, SRI4K,
SRIX4K
- ISO18092 / NFC: NFC Forum Tag Type 1-4
- Sony FeliCa1)
1) UID only, 2) UID only - read/write on request, 3) AES only.
4) read/write enhanced security features planned.
PLUG AND CHARGE YES ●
OCPP (BACK-END FUNCTIONALITY) OCPP, Open Charge Point Protocol enables connections
between Mobility Service Provider and Charge Point
Operator (if supported by operator):
• Real-time information about location, availability and price.
• A uniform way of exchanging data.
• Roaming system.
●
• Remote mobile support to access any charge station without pre-
registration.
• Communication via mobile application or SMS.

AUTHORIZATION USING PIN Users and PIN’s configurable through charger web
interface. ●
BASIC MECHANICAL SPECIFICATION
DIMENSIONS (HXWXD) 134.3 x 31.2 x 20.0 [cm], middle point height of charging sockets is 108 cm.
WEIGHT 38 kg (weight depending on the actual configuration).
DIMENSION INCLUDING PACKAGING (HXWXD) Packaging adds 10 cm to all dimensions of the product.
WEIGHT INCLUDING PACKAGING Packaging adds 5 kg to the charging station.
CASING MATERIAL Stainless steel with extra anti-corrosion protection (powder coated) and
polycarbonate display cover. UI holder material: fibre-reinforced ABS.
CASING COLOR Grey and grey.
Mechanical specification

• Non-default colour combinations available at a surcharge. Optional

INLET CABLE HANDLING

POWER CABLE ENTRANCE DIRECTION Power cables can be inserted into the station from the bottom of the charging
station.
POWER CABLE DIMENSIONS Up to 5 x 50 mm2 cables can be used directly. Customization for every customer
needs with additional clamps possible up to 135 mm2.
ETHERNET CABLE ENTRANCE Ethernet cables can be inserted into the station from the bottom of the charging
station.
ETHERNET CABLE TYPE CAT-5, RJ45 connector. SFTP preferred if layered with power cables or on long
distances. Cat-5 cable suggested longest distance without using signal repeaters is
100 m.

ENVIRONMENTAL SPECIFICATIONS
ENCLOSURE INGRESS PROTECTION IP 54
in testing with IK10. ●
TEMPERATURE RANGE Operation temperature range: -25 °C to +65 °C
Storage temperature range: -40 °C to +70 °C
Product extendable with thermostat and heater.
●
HUMIDITY Up to 95 % relative humidity, non-condensing
●
MAXIMUM ALTITUDE 2000 m
●
VANDALISM PROTECTION
IMPACT PROTECTION IK10
●
PLUG LOCKING Plug locking operation can be enabled or disabled in
charger configuration. Optional

DOOR LOCKING Three point door locking with single mechanism. Single key access. Door open
sensor. Device tilt sensor.
 MAINTENANCE
FIRMWARE UPDATE Firmware update done through backend system or web
interface. ●
ACCESS TO SERVICE AREA Service doors with key.
●
FUNCTIONS SUPPORTED THROUGH SERVICE AREA Access to:
• Ethernet.
• Mobile SIM.
• Charger system reset.
• Charger configuration reset.
• Protection manipulation. ●
• RCD protection test button (pressed once per year).
• Connection to the power supply.
• Configurable digital inputs (DI) and digital outputs (DO).

CLEANING • Cloth and water or water-based or alcohol-based

cleaners.
• Do not use solvent-based cleaners.
●
POWER MANAGEMENT
ECONOMIC/PRICE OPTIMIZATION • Based on energy tariffs.
• Time scheduling of charging towards lower tariffs or
self-consumption when user preferences and pricing
allows it.
●
• Evaluation of on-site production (e.g., photovoltaics).
OPERATION OPTIMIZATION • Machine learning and pattern recognition using built-in
AI to predict and optimise each charging session.
• Collection of user's departure time over app or touch
screen to refine automatically suggested charging profile.
• Support for Modbus protocol for integration with
●
external smart building systems.

PREVENT OVERLOADING MAIN FUSE – GRID CONNECTION By using Load Guard device:
POINT • Static limit of maximum allowed charging current per
phase.
Software solutions

• Static limit of maximum allowed charging current per

phase in case connection with Load Guard sensor / back-
end is lost.
• Detection and visualisation of available supply and
●
automatic adjustment of charging power.
• Detection and visualisation of surplus energy returned to
the grid (Production from renewable energy sources).

DEMAND RESPONSE ACTIVATION (BACK-END • Remote power manipulation by DSO.

FUNCTIONALITY) • Remote power manipulation by energy supplier. ●
MANAGING CLUSTER OF CHARGERS • Based on user preferences and current installation's load
conditions.
• Master-slave relationship with floating master. Power
management of up to 36 electric vehicles is possible. Valid
for the most unfavourable scenario with low power
capacity available, meaning constant need for power
management recalculations with inclusion of data
obtained from Load Guard. INCH Duo could also control ●
larger clusters, depending on the individual case.
• Larger cluster (supply of up to 300 electric vehicles in
most unfavourable scenario) is possible with use of
industrial computer and connection to Etrel Ocean
management software.