TREQ ONE

INSTRUCTION MANUAL
The setup of your rig is very dependent on body type, personal seating preferences and the
equipment you own, but to give you a head start, we included a setup scheme on the last page.

REQUIRED TOOLS:

4-6 mm

WWW.TREQ-SIM.COM
 GENERAL INSTRUCTIONS
The easiest way to mount the click-in-nuts, is to slide them in from one side of the profile. But
don't worry if you need to put in a click-in-nut in a profile which has both ends already closed: it
is also possible to push them in the T-slot anywhere you like!

1 2 3

Click!

The corner brackets feature 4 little hooks to stop the bracket from rotating once it is mounted
on a profile. But on some places of the rig these corner brackets are placed on a 90° angle of
the T-slot. In these situations it is recommended to break off 2 of the hooks, which is easily
done with a screwdriver or a pincer.

1 2 3

Break!

REQUIRED TOOL:

WWW.TREQ-SIM.COM
1

Profile 4040 L=478 Profile 4040 L=500 Profile 4080 L=500 Profile 4080 L=1170

2x 2x 2x 2x

Profile 4080 L=478 Profile 4080 L=580 Profile 4080 L=150 Corner Bracket

1x 2x 2x 20x

Pedal Bracket Left Pedal Bracket Right Side Bracket Bow Tie Plate

1x 1x 2x 1x

M8 Click-in-Nut M8x16 Cover 4040 Cover 4080

52x 40x 4x 8x
DEPENDING ON YOUR VERSION:

Wheel Deck Front Mount Asetek Mount Side Mount

WWW.TREQ-SIM.COM
Bags with bolts, nuts and washers:

M8 BOLTS AND WASHERS PEDAL MOUNTING RUBBER FEET

M8x12 (Round Head) Black 4 M6x12 Screw 2 M5x12 (Socket Head) 4

M8x20 (Socket Head) Black 12 M6x16 (Socket Head) 4 M5 T-Nut Click-in-Nut 4
M8x20 (Sunken Head) Black 8 M6x20 (Socket Head) 2 Rubber Foot 4
M8 Washer 8 M6x25 (Socket Head) 2
M6 Washer 4 WHEEL MOUNTING
CABLE MANAGEMENT M6 T-Nut Click-in-Nut 4
M8x16 (Sunken Head) 4
M4x12 Screw 5 M8 T-Nut Click-in-Nut 4
M4 T-Nut Click-in-Nut 5 You can use these on any place Wheel mount option
1
you like. Either inside the specific set of bolts.
Cable Binder 5
profile slot (just turn the bolt
through the tape), or by
pasting them.

2 Profile 8040 L=1170 (2x)

M5
M8
(16x) (4x)

M5
These come from the ‘Rubber Feet’ bag
(4x)

WWW.TREQ-SIM.COM
3
(4x)

M5x12

(4x)

4 Profile 8040 L=500 (2x)

M8

(12x)

WWW.TREQ-SIM.COM
5

M8x16

(16x)

6 Profile 4040 L=500 (2x)

M8

(4x)

WWW.TREQ-SIM.COM
7 Break the
pins!
M8x16

(8x)

The width of the two 4040

profiles is depended on your
seat, so you might want to
wait before tightening them!

8 Profile 8040 L=580 (2x)

M8
(12x)

WWW.TREQ-SIM.COM
9
M8x16

(8x)

10 Assembly of Pedal Bracket

Profile 8040 L=478 (1x)
Profile 4040 L=478 (2x)

M8x20
(Black)

(8x)

Do not tighten the profiles yet. Do this

after you’ve mounted your pedals!

WWW.TREQ-SIM.COM
11 Assemble the Pedal Brackets on the frame. Choose which holes you want to use as a
result of your desired Pedal Deck angle.

Washer

(2x)

M8x20

(4x)

12 Assembly of the Bow Tie

Do NOT tighten the screws yet.

M8x12

(4x)

WWW.TREQ-SIM.COM
13 Mount the Side Plates.
Same for left and right.

M8x20
(4x)

14a Mount the 150 profiles like this for

the Wheel Deck.
14b Mount the 150 profiles like this for
the Front and Side Mount.

M8x20

WWW.TREQ-SIM.COM
15a Wheel Deck

M8

M8x16

(4x)

15b (Asetek) Front Mount

M8

M8x16

(4x)

15c Side Mount

M8

M8x16

(4x)

WWW.TREQ-SIM.COM
16 Place all cover caps.

(16x) (4x) (8x)

17 Adjust Pedal Bracket and Wheel Mount Assembly to desired position (see step 18 for a
setup drawing).

WWW.TREQ-SIM.COM
 OPTIONAL: Some pedals, like Thrustmaster or Logitech, have threaded holes on the
bottom of the pedal base. To mount these type of pedals, please use the spare corner
brackets. Mount 1 side to a pedaldeck-profile and the other to the pedals.

For Fanatec or Heusinkveld pedals you can use click-in-nuts and mount them ‘from the
top’.

WWW.TREQ-SIM.COM
18 Setting up your rig in the perfect way can take a lot of time and adjustments. Everybody is
different, and with the enormous amount of sim racing gear available, it is impossible to draw you
the perfect seating position. But this page should help you when tightening all the bolts for the
first time. After you’ve build it up like this, you can then fine tune it to your own preferences.

Body length: 160 cm Body length: 180 cm Body length: 200 cm

A: 50 cm A: 55 cm A: 60 cm
B: 60 cm B: 65 cm B: 70 cm
C: 65 cm C: 70 cm C: 75 cm

When first building your rig, we recommend putting S on 35 cm. Don’t tighten
the bolts of the steering rack too much, ‘cause there is a big chance you’re going
to adjust it after you mount a steering wheel.

WWW.TREQ-SIM.COM