PRODUCED BY AN AUTODESK STUDENT VERSION

Paper air craft assembly guide

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

Boeing 737 family

little_model_airport
PRODUCED BY AN AUTODESK STUDENT VERSION
 PRODUCED BY AN AUTODESK STUDENT VERSION

Tools:
12 13 14 Cutter / Scalpel
Cutting mat
Double sided tape
Transparent tape
5 8.5 Glue (UHU)
10 9 8 7
2

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

16

18 17 6 22 11 4 1
16
3
10 9 8 7
5 8.5
15

1:400
12 13 14
19 20 21

Template printed on a piece of paper*

Template backed by one piece of paper* (template-paper)

Two sides of template glued onto the same pieces of paper # (template-paper-template)

Two sides of template glued onto two (or 3 if necessary if paper is too soft) layers of paper
(template-paper-paper-template), OR two sides of template glued onto the same pieces of
thin cardboard (template-cardboard-template)

! Glue is preferred to be used to mount template to cardboard, double sided tape can also be
used as an alternative .

* Best to be printed and backed by paper of at least 120g/m2.

B737
# Advised to glue paper to the back of one side of the template, cut it out, precisely align it to
little_model_airport
the back of the template of the other side, and cut it out from the template again.

PRODUCED BY AN AUTODESK STUDENT VERSION

 PRODUCED BY AN AUTODESK STUDENT VERSION

Tools:
12 13 14
Cutter / Scalpel
Cutting mat
Double sided tape
5 10 9 8 7
17 Transparent tape
16 Glue (UHU)

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

6 22 11 4 1 2 3
16
17 10 9 8 7
5

19 20 21 12 13 14

15

1:500
18

Template printed on a piece of paper*

Template backed by one piece of paper* (template-paper)

Two sides of template glued onto the same pieces of paper # (template-paper-template)

Two sides of template glued onto two (or 3 if necessary if paper is too soft) layers of paper
(template-paper-paper-template), OR two sides of template glued onto the same pieces of
thin cardboard (template-cardboard-template)

! Glue is preferred to be used to mount template to cardboard, double sided tape can also be
used as an alternative .

* Best to be printed and backed by paper of at least 120g/m2.

B737
# Advised to glue paper to the back of one side of the template, cut it out, precisely align it to
little_model_airport
the back of the template of the other side, and cut it out from the template again.

PRODUCED BY AN AUTODESK STUDENT VERSION

 PRODUCED BY AN AUTODESK STUDENT VERSION

01
Steps:

Parts: 2

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

Roll the fuselage and stick it

together with tapes.

02
Parts: 3

Parts: 2

Roll the tail and stick it onto

fuselage with tapes.

03
glue to cardboard

x3
uncut template
(mirror)
Parts: 4, 5

Parts: 3

Form tail fin and horizontal stabilizer,

glue onto tail fuselage

B737
little_model_airport

PRODUCED BY AN AUTODESK STUDENT VERSION

 PRODUCED BY AN AUTODESK STUDENT VERSION

04
Put in cards etc. Make sure the plane
in the front half is balanced or in

Parts: 2
the fuselage to "nose heavy"
balance the position
aircraft c.g.

Parts: 1
x2

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

Balance the fuselage and

attach the nose

05
Parts: 6,7,8,9,10,15,
737 NG: 11
737 MAX: 22

Wings structure
Glue together,
aline by inside
Top

Gently
fold leading
edges and flaps
Bottom

x2

06 x2
737 NG, Trim the inside of
Parts: wings 6 wings, ensure it

classic Ensure the upper and lower half

11
Front view
fits into the
wingbox
of wings are properly sealed

x2
Trim the inside of
Parts: wings, 16 737 MAX 16
6
22
wings, ensure it
fits into the
Ensure the upper and lower half Front view wingbox

Wings construction and

of wings are properly sealed,
winglets are located properly

winglets

B737
little_model_airport

PRODUCED BY AN AUTODESK STUDENT VERSION

 PRODUCED BY AN AUTODESK STUDENT VERSION

07
Parts: 19
Glue the wings
onto wingbox

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

Parts: 19 Make sure the wings are

symmetrical

Wings / fuselage connection

08
Parts: 17

Engine component
B737 NG/ classic engine
Side view

08
Glue the engine fan blades
and case in place
Parts: 18

Engine component
B737 MAX engine Isometric view Side view

B737
little_model_airport

PRODUCED BY AN AUTODESK STUDENT VERSION

 PRODUCED BY AN AUTODESK STUDENT VERSION

09
12
13 14

Parts: 12, engine, 13, 14

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

Engine assembly

10
Parts: 20,21

Parts: 19

Landing gear
Completion
x2

B737
little_model_airport

PRODUCED BY AN AUTODESK STUDENT VERSION