0% found this document useful (0 votes)
40 views5 pages

MSDS Starbrand Standard 2023

Uploaded by

Jhoreen Fabito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
40 views5 pages

MSDS Starbrand Standard 2023

Uploaded by

Jhoreen Fabito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

STARBRAND®STANDARD

BOARD

Material Safety Data Sheet (MSDS)

1 IDENTIFICATION OF THE MATERIAL AND SUPPLIER


Product Name STARBRAND®GYSPUM BOARD- STANDARD TYPE
Recommended Use Ceiling and wall for Interior application
Company Name PT. Siam-Indo Gypsum Industry
Jl. Inspeksi Kali Malang Km.2
Kampung Cikedokan
Kec. Cikarang Barat
West Java, Indonesia 17520

Issued date 14 July 2023

2 HAZARDS IDENTIFICATION
Hazard Classification Not classified as Hazardous. Not classified as Dangerous Goods.
The potential health hazards are related to dust generated from these materials
during the use of power tools and sanding.

Safety & Health The intact STARBRAND® Gypsum board does not give off dust or fume during
installation or when installed.
However, cutting, breaking, drilling, sawing, grinding and finishing may generate
dust. The following Risk and Safety phrases apply to airborne dust of this product :
Risk : Irritating to eyes, respiratory system and skin Repeated exposure, may
cause skin dryness or cracking
Safety: Do not breathe dust. Avoid contact with skin and eyes.
Wear suitable protective clothing, gloves and eye/face protection.

3 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients CAS NO PROPORTION
Natural Gypsum (CaSO4. 2H2O) 10101-41-4 >85%
Paper Liner 9004-34-6 >4%
Starch 9005-25-8 <1%
Accelerator 7778-80-5 <1%
Others - < 0.1 %
STARBRAND®STANDARD
BOARD
4 PHYSICAL AND CHEMICAL PROPERTIES
Appearance A rigid perforated sheet of gypsum board consisting of a gypsum
core encased in paper facing with fleece
Board density 600 - 660 kg/m3
Boiling point Not applicable
Melting point 1450o C (calcium sulphate dihydrate)
Vapor pressure Not applicable
Specific gravity (H2O = 1) 2.3 gr/cc (approximately)
Flash point Not applicable
Flammability limits Not flammable
Solubility in water Not soluble
Reactivity (e.g. with air or water) Not reactive
Auto-ignition temperature
Odor threshold -
Lower explosion limit Slight plaster odor
Upper explosion limit -
Self accelerating decomposition -
Total Volatile Organic Compound < 0.01 mg / (m3. hr)
Formaldehyde emission rate < 0.01 mg / (m3. hr)
Phenylcyclohexene emission rate 0
Total phthalate emission < 0.003 mg/m3
Total particles emission 4. HEALT < 0.02 mg / (m3. hr)

5 FIRST AID MEASURES


The following applies to dust from these products:
Swallowed Rinse mouth and lips with water. Do not induce vomiting. If symptoms
persist, seek medical attention.
Eyes Flush thoroughly with flowing water, while holding eyelids open, for 15
minutes to remove all traces. If symptoms such as irritation or redness
persist, seek medical
Skin Wash off skin thoroughly with water. Use a mild soap if available

Inhalation Remove to fresh air, away from dusty area. If symptoms persist,seek
medical attention.
First aid Facilities Eyewash station and washroom
Advice to Doctor Treat symptomatically.
STARBRAND®STANDARD
BOARD
6 FIRE FIGHTING MEASURE
Flammability The gypsum plaster core is non-flammable.
The paper liner will smolder and burn in a fire.

Suitable extinguishing Use carbon dioxide, foam, dry chemical or water spray to
Media Extinguish, as required for fire in surrounding materials.

Hazards from None


Combustion Products

Special Protective Wear full protective clothing and self-contained breathing apparatus
Equipment for (SCBA). Extinguish with alcohol-resistant foam, carbon dioxide, dry
Firefighters powder or water fog. As required for fire in surrounding materials.
equipment for fire fighters

7 ACCIDENTAL RELEASE MEASURES


Clean Up Procedure Dust and waste should be cleaned up by bagging, wet sweeping and/or
vacuuming

8 HANDLING AND STORAGE


Precautions for safe Minimize dust generation and accumulation. Use good safety and
handling industrial hygiene practices. Follow traditional building practices; such as
management of water away from the interior of the structure to avoid
the growth of mold, mildew and fungus. Remove any building products
suspected of being exposed to sustained moisture and considered
conducive to mold growth from the jobsite.
When moving board with a forklift or similar equipment, it is essential
that the equipment berated capable of handling the loads. The forks
should always be long enough to extend completely through the width of
the load. Fork spacing between supports should be one half the length of
the panels or based being handled so that the maximum of 1.2 meter
extends beyond the supports on either end. Use local exhaust or general
dilution ventilation or other suppression methods to maintain dust level
below exposure limits.

Condition for safe Store in a cool, dry, ventilated area away from sources of heat, moisture
storage, including and incompatibilities. Protect product from physical damage. Protect
any incompatibilities from weather and prevent exposure to sustained moisture. Gypsum
association literature recommends storing board flat to avoid damaging
edges, warping the board and the potential safety hazards of the board
falling over.
STARBRAND®STANDARD
BOARD

9 EXPOSURE CONTROLS/PERSONAL PROTECTION


Workplace Exposure Standards for Ambient Air Standard Quality
Must follow The Regulation of The Government of Republic of Indonesia No. 41/1999
Maximum value for indoor = 10 mg/m3 and outdoor = 230 ug/Nm3
Biological limit values
No biological limit allocated.
Personal Protection Equipment (PPE):
Respiratory Protection Under ordinary conditions no respiratory protection is required.
Wear SNI approved respirator that is properly fitted and is in good
condition when exposed to dust above exposure limits.

Eye Protection Wear SNI approved glasses or safety goggles when handling drywall to
prevent dust coming in contact with eyes. Wearing contact lenses when

Skin Protection Using drywall, under dusty conditions, is not recommended.


Wear gloves when handling drywall. Remove clothing and protective
equipment that becomes dusty and launder before reusing.

10 STABILITY AND REACTIVITY


Chemical Stability Stable
Incompatible material None
Condition to avoid Dust generation
Hazardous Reaction None.

11 TOXICOLOGICAL INFORMATION
Toxicology data: Not available on this product, but anticipated to be very low with LD50 >5000 mg/kg.

Toxicology data: Not available on this product, but anticipated to be very low with LD50 >5000
mg/kg.
Health effects : Acute (short term)
Swallowed Unlikely under normal industrial use, but swallowing may result in nausea or
abdominal discomfort
Eyes Dust is irritating to the eyes causing watering and redness. Exposure to dust may
aggravate pre-existing eye conditions
Skin The dust from this product, particularly in association with heat and sweat, may
cause mild irritation and drying to the skin due to its physical characteristics
Can cause irritation of the nose, throat and lungs resulting in excess mucus and
Inhaled coughing
STARBRAND®STANDARD
BOARD
12 ECOLOGICAL INFORMATION
Eco-toxicity The physical and chemical nature of the product, and toxicological data on ingredients,
Indicate that this product is relatively low risk
Persistence and Product is persistent and would have a low degradability degree adability
Mobility A low mobility would be expected in a landfill situation.

13 DISPOSAL CONSIDERATIONS
Waste should be placed in containers and disposed of with other construction waste in accordance
with local authority guidelines. Measures should be taken to prevent dust generation during disposal
and exposure and personal precautions should be observed (as section 9)

14 TRANSPORT INFORMATION
Not classified as hazardous for transport

15 REGULATORY INFORMATION
No special labeling required.

16 OTHER INFORMATION
Prepared By: PT. Siam-Indo Gypsum Industry
Issued date: 23/02/2021
Additional Information
Hazardous Material Identification System (HMIS) Classification
1 Health = 1. Denotes possible chronic hazard if airborne dusts or fumes
Health Hazard
are generated Irritation or minor reversible injury possible
Fire Hazard 0 Fire = 0, Materials that will not burn
0 Physical hazard = 0, Materials that are normally stable, even under
Physical Hazard fire condition, and will not react with water, polymerize, decompose,
condense, or self-react Non explosives
National Fire Protection Association (NFPA)

0 Health = 1, Exposure could cause irritation but only minor


residual injury even if no treatment is given
1 0 Flammability = 0, Material that will not burn
Instability = 0, Normally stable, even under fire exposure
conditions, and are not reactive with water

Disclaimer: The information is taken from sources or based upon believed to be reliable. It is offered for your consideration, investigation
and verification. Attention is drawn to the possible risks when using the product for other use than it has been originally designed for.
Thereby, we make no warranty of merchantability or any other warranty, express or implied, with respect of such information, and we
assume no liability resulting from its use. This document does not exempt users from knowing and abiding the legislation ruling their
activity. In no way shall the company be liable for any claims, losses, or damages of any third party or for lost profits, or any special,
indirect, incidental, consequential or exemplary damages, however arising, even if the company has been advised of the possibility of such
damages.

You might also like