Quick Installation Guide

Live!
Titanium
 Contents

1. Live! overview............................. 2

2. Installation...................................... 4

3. Network setup................................. 7

4. Wireless setup................................. 8

5. Configuring your Live!...................... 9

6. Troubleshooting.............................. 10

1
1. Live! overview
User interfaces 4

Description
3
1 Live! Telephony ports

2 Live! Ethernet LAN ports 7

3 Live! USB 2.0 port 5
4 Reset touch button

5 WPS touch button

6 Element power port 8

7 Universe CATV connector

8 Hybrid Interface connector

Depending on your specific product type, port

configuration may differ.

1 2

2
Status feedback LEDS: Touch buttons:

Note: The buttons only need to be touched and do not require

Activity Description
physical pushing. When a button is being touched, the nearest
On Powered successfully LED will blink rapidly.
Off Power not connected

On Optical link activated

Function Action
Off No optical link
Reboot • Hold button until all LEDs blink once
On CATV enabled
(after 5 seconds)
Off CATV disabled
• Release button to initiate reboot

Factory • Hold button until all LEDs have blinked

On Successful data uplink Default twice (after 10 seconds)
On (red) Hardware error • Release button to initiate a Factory
Blink Firmware upgrade / Default reset. The Live! will reboot
provisioning initializing automatically
Off No data uplink

On Phone line enabled WPS • Hold button touched until all LEDs blink
Blink Phone line initializing once (after 2 seconds).
Off Phone line disabled • Release button to initiate WPS on WLAN

On Internet connection enabled

Blink Internet connection initializing
Off Internet connection disabled Note: If a second WLAN interface is available, WPS for
the second WLAN interface can be initiated by holding
On WLAN enabled the WPS button until all LEDs have blinked twice (after
Blink WPS active 5 seconds).
Off WLAN disabled

LAN ports Green Link

Yellow Activity

3
2. Installation
Step 1: Installing the Hybrid Live! Step 2: Powering the device
Click the Hybrid Live! module on the Hybrid Element, as Connect the 12V plug of the supplied adapter to the Hybrid
shown in the picture. Element and connect the adapter to a power socket. The unit
Note: Proper installation does not require excessive force. will now start up. During the start-up sequence the
LEDs are on, other LEDs may blink.
When the start-up sequence has finished the following LEDs
should be on: .

1 The complete start-up sequence may take several minutes.

Click!
2

4
Step 3: Connecting your computer Step 4: Connecting your telephone
Connect your computer to one of the Ethernet LAN ports This step is only relevant if the Hybrid Live! has voice ports.
on the Hybrid Live!, using an Ethernet cable with a RJ-45
connector. Your provider can tell you which ports to use. A standard analog telephone handset can be connected to the
active voice ports, using a RJ-11 cable. The LED indicates
Note: refer to section “fixed network setup” if your connection if voice is enabled and operating correctly. Your provider can
is not working directly from the start. tell you which ports to use.

Reference image of
the back of a PC

5
Step 5: Connecting your analog television or radio Cleaning instructions:
This step is only relevant if your Hybrid configuration has a
CATV receiver. Your Hybrid product may be cleaned using a soft, dry cloth.
For areas of persistent dirt, a damp cloth may be used with
Connect your analog television or radio using a coaxial cable mild detergent. Product and LED logos may be damaged
with a male F-connector. The LED indicates if CATV by using aggressive cleaning products or ethanol-based
service is enabled. cleaners - if in doubt do not clean near these logos. Under
no circumstances allow water or cleaning fluid to ingress the
product, as this may cause permanent damage and prevent
correct operation.

6
 3. network setup
Step 1: Step 3:
Open the web browser on your computer and check if your Open your web browser and check if your connection is
connection is working. If your connection is working, you can working. If your connection is not working, please refer to the
skip step 2 and 3. troubleshooting section.

Step 2:
(Instructions for Windows Vista / Windows 7; for other
operating systems please contact your service provider)

• On your computer, go to “Start” at the bottom left

corner and click on “Control Panel”.
• The Control Panel window will appear. Click on “View
Network Status and Tasks” at the “Network and Internet”
category.
• The Network and Sharing Centre will appear:
• For Windows Vista: Click on “Manage network
connections” at the top left hand corner.
• For Windows 7: Click on “Change adapter
settings” at the top left hand corner.
• Right click on the correct “Local Area Connection”
by identifying the correct network card and click
“Properties”.
• Select “Internet Protocol Version 4 (TCP/IPv4)”. Click on
“Properties”
• Select “Obtain an IP address automatically”, and “Obtain
DNS server address automatically”. Save the settings by
clicking “OK”, and close the window by clicking “OK” or
“Close”.

7
4. Wireless setup
This section is only relevant if wireless functionality is Step 2:
available on your Hybrid Live!. The LED indicates if (Instructions for Windows Vista / Windows 7; for other
wireless functionality is enabled. operating systems please contact your service provider)

Step 1: • Go to “Start” at the bottom left corner and click on

To set up the wireless connection between your computer and “Control Panel”.
the Hybrid Live! you may need the SSID and WPA key of the • The Control Panel window will appear. Click on “View
Hybrid Live!. The SSID is the name of the wireless network. Network Status and Tasks” at the “Network and
The WPA key is the password needed for your secured wire- Internet” category.
less network. The default SSID and the WPA key are printed on • The Network Connections window will appear. Click
the label on the rear of your Hybrid Live!. on the “Connect to a network”.
• Show “Wireless” and select the network (SSID) that is
printed on the label.
You may write down these values here: • If requested press the WPS button on your Hybrid
Live!. Alternatively you can connect using the WPA key
that is printed on the label.
SSID: _____________________________________________________ • Your connection is now operational. Open your web
browser and verify that your connection is working.
If your connection is not working, please refer to the
WPA key: _________________________________________________ troubleshooting section.
• After installation you can manually change the SSID
and WPA key, by using the web-interface of the Hybrid
Live!.

8
 5. Configuring your Live!
Note: By default the router is configured properly for most
home networks. Changing the configuration is only advised
for advanced users and might interrupt your connection.
Please refer to page 3 on how to reset the router settings back
to the factory default settings.

Step 1:
• Launch the web browser on your computer and enter
the router’s default IP address ‘192.168.1.254’ in the
address field. This address is also printed on the label
on the back of your Hybrid Live!.

Step 2:
• Log in as ‘admin’, using the default password ‘admin’.

It is strongly advised to change the password after you

logged in for the first time.

Step 3:
• Configure the router to the desired configuration. Read
the help text for additional information about this
setting.

9
6. Troubleshooting
Issue Action

LED is off Make sure you have connected the Hybrid Element to a working power outlet, using
the adapter shipped along with it. If the LED remains off, please contact your service
provider.

LED is off There is no valid link on the fiber port. Please contact your service provider.

LED is off There is no valid CATV signal on the Universe CATV connector. Please contact your
service provider if a CATV signal is expected.

Red LED is on Hardware error. Power down the device, wait for 1 minute, then power the device back
on. If the problem persists, contact your service provider.

LED is off Voice functionality is not enabled. Please contact your service provider if voice func-
tionality is expected.

LED keeps blinking Voice service initialization not completed. Please make sure the phone is not off-hook
and the phone line is connected to the correct port. If this issue persists, contact your
service provider.

10
Issue Action

LED is off Internet connectivity is not enabled. Please contact your service provider if routing
functionality is expected.

LED keeps blinking Internet service initialization not completed. If this persists, contact your service
provider.

LED is off Please check in the web interface if wireless functionality is enabled. Please contact
your service provider if wireless functionality is expected.

Web interface is not reachable Check if Internet functionality is enabled , and if you have the correct router IP ad-
dress. If you changed the router IP address, you can perform a “Factory Default reset”
to restore the default IP address.

How to reset the router settings? See page 3

11
Europe-EU Declaration of Conformity

Hereby, Genexis BV declares that this product is in compliance

with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
Copyright © Genexis 2012 rev. 3