10/25/24, 1:39 PM SIS 2.

2023/11/30 Wheel Spindle - Remove (KENR6018-15)

SMCS - 4234 i10052660

Removal Procedure
PIP
Table 1 -
202 1098
Tool Part Number
Required Tools
4
05: 10/2 809
Part Description
/ 0 Qty
A
B
5P-2968
1P-2322
Jack Adapter
3
KE 9:34+ 5
Combination Puller
1
1
C 589-7436
N
© 2 R60 08:00
Link Bracket As 1

Start By:
024 18
a. Remove the wheels (front).
Cat
erp
illa
NOTICE
rI
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and nc.
repair of the product. Be prepared to collect the fluid with
suitable containers before opening any compartment or
disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool

Catalog" for tools and supplies suitable to collect and contain
fluids on Cat® products.

Dispose of all fluids according to local regulations and

mandates.

NOTICE
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component

life.

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 1/7
10/25/24, 1:39 PM SIS 2.0

Illustration 1 g00932128

Illustration 2 g00932130

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 2/7
10/25/24, 1:39 PM SIS 2.0

1. Remove bolts (4) and cover (2) from wheel spindle housing (1). Drain the oil from wheel spindle
(3) into a suitable container for storage or disposal.

2. Remove O-ring seal (5) from cover (2).

Illustration 3 g00932134

3. Remove bolts (8), retainer (7), and the shims.

4. Loosen bolt (6).

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 3/7
10/25/24, 1:39 PM SIS 2.0

Illustration 4 g00932136
5. Install Tooling (A) under the head of bolt (6).

6. Tighten bolt (6) to secure Tooling (A) in position.

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 4/7
10/25/24, 1:39 PM SIS 2.0

Illustration 5 g00932151
7. Fasten Tooling (C) and a suitable lifting device onto wheel spindle (3). Tighten Tooling (A)
against the shaft of the wheel spindle to force the spindle outward. Hit the flange of the wheel
spindle with a hammer to assist Tooling (A) in forcing the spindle out of the spindle housing.
Repeat this step until wheel spindle (3) is loose from bearing cone (9).

8. Remove wheel spindle (3) from the wheel spindle housing. The weight of wheel spindle (3) is
approximately 57 kg (125 lb).

9. Remove Duo-Cone seal (10) from wheel spindle (3). Remove Duo-Cone seal (11) from wheel
spindle housing (1).

10. Remove Tooling (A) and bearing cone (9) from wheel spindle housing (1).

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 5/7
10/25/24, 1:39 PM SIS 2.0

Illustration 6 g00932188
11. Remove bearing cups (12) from the wheel spindle housing.

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 6/7
 N +
© 2 R60 08:00
10/25/24, 1:39 PM SIS 2.0

024 18
Cat
erp
illa
r In
c.

Illustration 7 g00932189
12. Use Tooling (B) to remove bearing cone (13) from wheel spindle (3).

13. Repeat this procedure for the remaining wheel spindle.

PIP-10980809
2024/10/25
05:39:31+08:00
i04987340
© 2024 Caterpillar Inc.

https://sis2.cat.com/#/print-preview/service/cb85c07c-be43-426e-a15e-b784d7c278bf 7/7