Technical Information

SystemStakTM Valves
DGMxx-7 20/30 Design

BC430262051397en-000101
SystemStak™ Valves
ISO 4401 size 07; 315 bar (4500 psi); up to 200 L/min (53 USgpm)

General Description The units are performance rated up to: 200 L/min (53 USgpm)
This range of stackable hydraulic controls are designed to be 315/350 bar (4500/5000 psi)
mounted under a size 7 directional valve such as Danfoss DG*V- The range comprises:
7, solenoid controlled and pilot operated. With their cartridge DGMX-7 .......................................... Pressure reducing module
design they will provide a compact hydraulic circuit at reduced DGMC-7 ............................................... Pressure relief module
cost with the elimination of interconnecting piping. Servicing DGMFN-7 ............................................ Flow restrictor module
is simplified with access to working parts achieved without DGMPC-7 ................................... Pilot operated check module
removing valves from an assembled stack.

Table of Contents
Function Basic symbol Basic model Features Page

Reducing DGMX Piloted from (and reduced 3

pressure in) port P, A or B

Relief DGMC Single, dual and crossport models 5

Pilot operated check DGMPC Single in port A or B; dual 7

in ports A and B

Flow restrictor DGMFN Single or dual port, 10

meter-in or meter-out

2
SystemStak™ Pressure Reducing Valve Modules
DGMX-7

General Description
These two-stage adjustable pressure reducing modules The valve elements are formed as cartridges for ease of
are used to regulate the downstream pressure in the line construction and servicing.
in which the integral reducing valve is installed, whilst the
upstream pressure fluctuates above the reduced pressure.

Model Code
(F3-) DGMX-7 - P * - * - * -20

1 2 3 4 5 6 7

1 Special seals for 4 Function Ports 5 Pressure adjustment 6 Adjustment method

phosphate ester fluids PP – pressure reducing range W – screw and lock nut
Omit for standard seals; see “Hy - function in the P line, piloted B – 10 to 100 bar (145 to 1454 psi) H – hand wheel with locknut
draulic fluids” in “Further from P C – 10 to 160 bar (145 to 2326 psi)
Information” section. PA – pressure reducing function F – 10 to 250 bar (145 to
in the P line, piloted from A 3635 psi) 7 Design number,
PB – pressure reducing function G – 350 bar (5000 psi) Subject to change. Installation di -
2 Stak Module Reducer in the P line, piloted from B mensions unchanged for numbers
20-29 inclusive.

3 Size
ISO 4401-7

Functional Symbol
M M M

X P T B A Y X P T B A Y X P T B A Y

Operating Data
Basic Characteristics

Maximum flow 250 l/min (66 USgpm)

Maximum operating pressure 350 bar (5076 psi)
Operating temperature -25 to +80°C (-13 to +176°F)
Pilot drain flow 0,5 L/min (0.13 USgpm)
Weights 8,65 kg (19.06 lb)

Performance Data
Performance Characteristics
Typical performance with petroleum oil at 36 cSt (169 SUS)
and 50°C (122°F).

Reduced Pressure Underride

At cartridge outlet for various pressure settings.

3
Installation Dimensions in mm (inches)
DGMX-7

90 272.7... 278.7
1.8 40 50 4.7 170 98... 104

1)
G1/4"
27

M
80
53

53
13

22
2) T P X Ma = 30 ± 1.5 [Nm]
Ø3
3

46
1 2 3
Ma = 200 ± 10 [Nm]
14

T P
X s1 4
40
10

A B
Y

3)

H Option- Hand Wheel

Ø 32

109.5 ... 115.6

W Option- Screw and Locknut

109

For all models, to increase pressure setting, unlock and turn For additional dimensions, contact your Danfoss representative.
the adjuster clockwise, viewed at the adjuster end. Turn
counter-clockwise to decrease pressure setting.
Type H adjustment settings can be secured by tightening the
lock screw in the end of the thimble.

4
Pressure Relief Valve Modules
DGMC(2)-7

General Description
These two-stage adjustable pressure relief modules are used
to limit the maximum pressure in the lines from which the
integral relief elements are fed.
The relief elements are formed as cartridges for ease of
construction and servicing.

Model Code
(F3-) DGMC-7- ** - * * -20

1 2 3 4 5 6 7

1 Special seals for 4 Function 5 Pressure adjustment 6 Adjustment method

phosphate ester fluids AT – Limits pressure in A, range W – screw and lock nut
Omit for standard seals; see discharges to T B – 10 to 100 bar (145 to H – hand wheel with lock nut
“Hydraulic fluids” in “Further 1454 psi)
BT – Limits pressure in B,
C – 10 to 160 bar (145 to
Information” section of discharges to T 2326 psi)
catalog. PT – Limits pressure in P, 7 Design number,
F – 10 to 250 bar (145 to
20 series
discharges to T 3635 psi)
2 Stak Module Relief Subject to change.
G – 350 bar (5000 psi)
Installation dimensions
unchanged for design
3 Size numbers 20-29 inclusive.
ISO 4401-07

Functional Symbol

X P T B A Y X P T B A Y X P T B A Y

Operating Data
Basic Characteristics
Maximum flow 300 l/min (80 USgpm)
Maximum operating pressure 350 bar (5076 psi)
Note that back pressure in line T, into which the valve’s pilot drain is internally connected, increases the effective
setting.
pressure
For pressure adjustment ranges see “Model Code”.
Operating temperature -25 to +80°C (-13 to +176°F)
Pilot drain flow 0,5 L/min (0.13 USgpm)
Weights 8,55 kg (18.84 lb)

Performance Characteristics
Typical performance with petroleum oil at 36 cSt (169 SUS)
and 50°C (122°F).

Pressure Override at Cartridge Inlet

At various pressure settings and cartridge outlet at 0 bar/psi.

5
Performance Data

268 ... 274 90

98 ... 104 170 45 45 1.8

s1 4
1)

27

80
53
13

22 T P X 2)

3
Ma = 30 ± 1.5 [Nm] Ø3

3 1 2
46
Ma = 200 ± 10 [Nm]
55
10

3) T P
X

A B
Y

H Option - Hand Wheel

Ø 32

109.5 ... 115.6

W Option - Screw and Locknut

109

For all models, to increase pressure setting, unlock and turn For additional dimensions, contact your Danfoss representative.
the adjuster clockwise, viewed at the adjuster end. Turn
counter-clockwise to decrease pressure setting.
Type H adjustment settings can be secured by tightening the
lock screw in the end of the thimble.

6
SystemStak™ Pilot Operated Check Valve
DGMPC-7

General Description General

The DGMPC hydraulic operated check valve is of a sandwich
Features:
plate design. They are used for leak-free closure of one or
• Industry Standard Mounting, ISO 4001-7, NFPA T 3.51 M both service ports, even for long periods of time. Free flow
R1 and ANSI B 93.7 D07 occurs from A1 to A2 or B1 to B2. Flow in the opposite
• For use in vertical stacking assemblies direction is blocked. The fluid flows from A1 to A2, the piston
(1) is pressurised and is pushed to the right, thereby opening
• For the leak free closure of one or both service ports the ball poppet (2) which then opens the main poppet (3). In
order to ensure correct closing of the valve, the service ports
of the directional valve must be connected to tank in the
neutral position (see typical circuit).

4
1 Piston
2 Ball Poppet
3 Main Poppet
1 2 3 4 Area A1
6 5 5 Area A2
6 Area A3

A1 B1

A2 B2

Model Code

(F3) - DGMPC - 7 - AB - *- (BA) - (*) - 30

1 2 3 4 5 6 7 8

1 Seal Options 2 Stack module, piloted 5 Cracking Pressure 7 Cracking Pressure (Dual
operated check valve line only)
F3 – Fluorocarbon seals, for K – 3 Bar
Phosphate Ester (class L – 5 Bar K – 3 Bar
L-HFD) 3 Size M – 7.5 Bar B – 5 Bar
Blank – Nitrile, for Mineral oil ISO 4401-07 N – 10 Bar M – 7.5 Bar
Anti-wear hydraulic N – 10 Bar
oil (class L-HM),
4 Check Valve Line 6 Check Valve Line
Invert emulsion 8 Design Number
AB – A piloted from B BA – B piloted from A
(class L-HFB) Water
BA – B piloted from A 30
glycol (class L-HFC) (Dual line only)
(Single line only)

7
Functional Symbols

Typical Cir cuit S ymbols

A2 B2 A2 B2 A2 B2

A2 B2 A1 B1 A1 B1 A1 B1

AB*- BA * AB* BA *

A1 B1
A B

P T

Operating Data
Technical Data

Maximum Flow (L/min) 300

Maximum Operating Pressure (bar) 315
Cracking Pressure See “Characteristic Curves” graph
Area Ratio A1/A2 = 1/11.8;A3/A2 = 1/2.8
Fluid Mineral oils or phosphate ester
Fluid Temperature Range (0C) -20 to 80
Fluid Viscosity Range (mm2/S) 2.8 to 500
Fluid Cleanliness Level (ISO) 19/17/14
Weight (Kg) 6.5

Performance Data
Characteristic Curves Solid Line
(measured at A1 - A2; B1 - B2
v = 41 mm2/s and t =
50ºC)
Dotted Line
A2 - A1; B2 - B1

Cracking Pressure:
K = 3 bar
L = 5 bar
M = 7.5 bar
N = 10 bar

8
Installation Dimensions (in mm)

80
47.5
φ3
3

3
1

101.6±0.2
88.1±0.2
76.6±0.1
65.9±0.2
50±0.2 2 x φ4
4
34.1±0.2
18.3±0.1

T P X

69.9±0.2
1.5
55.6±0.2

54±0.2
L

91
30.5±0.2
35±0.1

A B Y

12.7±0.2
14.3±0.2

1.5

2
199

Required surface finish of mating face

0.01/100mm
0.8

1 Name plate
2 Valve mounting holes
3 Locating pins
4 Locating pin holes

Mounting bolts: 3/8-18 (4) & 1/4-20 (2), SAE, Grade 8; M10 (4) & M6 (2), DIN912-10.9;
ISO 898,
Class 12.9
O-rings: 22mm x 2.5mm for ports A,B,P and T.
O-rings: 10mm x 2mm for ports X,Y, and L.

9
SystemStak™ Throttle Valve with Check
DGMFN-7

General Description General

DGMFN valves have double throttle/check valves in a
Features:
sandwich plate design. They are used to limit main flow
• Industry standard mounting, at one or two actuator ports. Two symmetrically arranged
ISO 4401-7, NFPNA-T-3 .5.1-M-R-I, ANSI B 93.7 D07 throttle/check valves limit flow (by means of adjustable
• Sandwich plate design throttle spools) in one direction and permit free return flow in
the other direction.
• Limiting of main flow of two actuator ports
• Meter-in or meter-out control Main flow limiting
The double throttle/check valve is fitted between the
directional valve and the subplate to change the speed of an
actuator (main flow limiting)

3 4 5
2

1 Throttle Adjustment Screw

2 Spring
3 Spool
4 Valve Body
5 O-Ring

Model Code

F3 - DGMFN - 7 - * - A2W - B2W - 30

1 2 3 4 5 6

1 Seal Options 2 Stack module, throttle 4 Direction of flow 5 Control line (Wrench
valve with check control adjustment)
F3 – Fluorocarbon seals, for
Phosphate Ester (class Y – Meter out Both port A and B
X – Meter in
L-HFD) 3 Size
YX – Meter out A, meter in B
Blank – Nitrile, for Mineral oil ISO 4401-07 XY – Meter in A, meter out B 6 Design Number
Anti-wear hydraulic
30
oil (class L-HM),
Invert emulsion
(class L-HFB) Water
glycol (class L-HFC)

10
Functional Symbols

A B A B A B A B

A Meter -out control A Meter -in control

Meter -in control...X Meter -out control...Y B Meter -in control: YX B Meter -out control: XY

Operating Data
Technical Data

Maximum Flow (L/min) 250

Maximum Working Pressure (bar) 315
Fluid Mineral oils or phosphate ester
Fluid Temperature Range (0 C) -20 to + 80
Fluid Viscosity Range (mm2/S) 2.8 to 500
Fluid Cleanliness Level (ISO) 19/17/14
Weight (Kg) 4.7

Performance Data
Characteristic Curves
Throttle flow pressure drop Check free flow pressure dro p
(measured at
v = 41 mm2/s and DGMFN- 7 DGMFN- 7
Pressure Drop in bar

t = 50ºC) 4 5 6 6.5 7 7.5 8 8

8.5 6
200 4
2
150
Throttle setting in turns
Pressure Drop in bar

9 0 40 80 120 160 20 0 240

100 Flow in L/min

50 10

12
10 14
5 16

0 50 100 150 200 250

Flow in L/min

11
Installation Dimensions
(Dimensions in mm)

Max. 294 91
Min. 246

51
1 2 3 φ3

3
4

76.6
34.1
2 x φ4
18.3 5
8
P
T X
71.5

69.9
L

55.6
54
A B
Y 35
24.8

72.2 34.1
12.7
14.3
1.6

50
65.9
7 88.1 Required surface finish of mating face
101.6 6
0.01/100m
m
0.8

1 Name plate
2 Screw for flow adjustment
3 Turn anti-clockwise = increases flow, turn clockwise = decreases flow
4 Two locating pins
5 Two locating pin holes
6 Valve mounting holes
7 O-ring ports A,B,P,T
8 O-ring ports X,Y,L

Mounting bolts: ½-UNC, SAE, Grade 8; M10 (4) & M 6 (2) , DIN912-10.9; ISO 898, Class 12.9
O-Ring: size 22mm x 2.5mm for port A,B,P and T
O-Ring: size 10mm x 2mm for port X,Y, and L

12
Products we offer: Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electric components. We specialize in providing state-of-the-art technology and solutions
• Cartridge valves
that excel in the harsh operating conditions of the mobile off-highway market as well as the
• DCV directional control marine sector. Building on our extensive applications expertise, we work closely with you to
valves ensure exceptional performance for a broad range of applications. We help you and other
• Electric converters customers around the world speed up system development, reduce costs and bring vehicles
• Electric machines and vessels to market faster.
• Electric motors Danfoss Power Solutions – your strongest partner in mobile hydraulics and mobile
• Gear motors electrification.

• Gear pumps Go to www.danfoss.com for further product information.

• Hydraulic integrated We offer you expert worldwide support for ensuring the best possible solutions for
circuits (HICs) outstanding performance. And with an extensive network of Global Service Partners, we also
• Hydrostatic motors provide you with comprehensive global service for all of our components.
• Hydrostatic pumps
• Orbital motors
• PLUS+1® controllers
• PLUS+1® displays
• PLUS+1® joysticks and
pedals
• PLUS+1® operator
interfaces
• PLUS+1® sensors
• PLUS+1® software
• PLUS+1® software services,
support and training
• Position controls and
sensors
• PVG proportional valves
• Steering components and
systems
• Telematics Local address:

Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com

Danfoss
Power Solutions Trading
Danfoss Danfoss Danfoss (Shanghai) Co., Ltd.
Power Solutions (US) Company Power Solutions GmbH & Co. OHG Power Solutions ApS Building #22, No. 1000 Jin Hai Rd
2800 East 13th Street Krokamp 35 Nordborgvej 81 Jin Qiao, Pudong New District
Ames, IA 50010, USA D-24539 Neumünster, Germany DK-6430 Nordborg, Denmark Shanghai, China 201206
Phone: +1 515 239 6000 Phone: +49 4321 871 0 Phone: +45 7488 2222 Phone: +86 21 2080 6201

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.