Scribd
Upload
75 views

BCME Question Bank (ME Part Only)

Nvvh

Uploaded by

ashok pradhan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
75 views

BCME Question Bank (ME Part Only)

Nvvh

Uploaded by

ashok pradhan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Question Bank

Sub: BCME (ME part only)


2nd Semester B Tech (Sec: I & L)
Short Answer Types
Module III
1. What is a hydro power plant?
2. Show the energy conversion in a hydro power plant.
3. What is the function of surge tank in hydro power plant?
4. What is a hydraulic turbine? Give example.
5. Name any two turbine according to the direction of flow through the runner.
6. Differentiate between impulse & reaction turbine.
7. Differentiate between a Turbine & a Pump.
Module IV
8. Define a heat engine.
9. What are the classification of engines?
10. What are the major components of a 2stroke SI engine?
11. What are the major components of a 4 Stroke SI Engine?
12. What is the function of a deflector in a 2 stroke engine?
13. What is function of a carburettor in a SI engine?
14. Define the terms: Stroke, Clearance Volume, Compression ratio
15. What are the compression ratio of a typical SI and CI engines?
16. Define refrigeration and refrigerant.
17. Define COP of a refrigerator.
18. Give two examples of each from Primary and secondary types of refrigerants.
19. What are the desirable properties of an ideal refrigerant?
20. What are the major components of a Simple Vapour Compression refrigeration cycle?
21. Define the terms: Compressor, Condenser and Evaporator.
22. What is function of an Expansion valve in a Vapour Compression refrigeration cycle?
23. Define tonne of refrigeration.
24. What are the major components of a Steam thermal power plant?
25. What are the different types of Boilers?
26. What are the different Boiler mountings?
27. What are the different Boiler accessories?
28. What are the different components of Automobile Transmission System?
29. Define Clutch and its use power Transmission.
30. What the function of gearbox in automobile transmission?
31. What is the function of differential in automobile?
32. What are the different components of a drum brake or internal expanding shoe brake?
33. Define brake and Clutch.
34. What is the function of Universal joint or Hooke’s joint in automobile transmission?
Module V
35. Define robots and its application.
36. What are the different basic components of a robot / robotic system?
37. What are the different applications of robots?
38. What are the components in a robot that interact with the outside world?
39. Define Foundry practices?
40. Define a pattern.
41. Define a Mould.
42. Define casting.
43. Define a gating system used in casting.
44. What are cope and drag in casting?
45. Define a bloom.
46. Define a billet.
47. Define a Slab.
48. Define a Sheet.
49. Give four examples of cutting operations performed on sheet metal.
50. Give four examples of forming operations performed on sheet metal.
51. Give the name of 2 sheet metal materials.
52. Differentiate between Sheet and Strip.

Focused Question Types


Module III
1. What are different components of Hydro power plant?
2. Define different heads of hydro power plant.
3. Define Hydraulic efficiency, Mechanical Efficiency & Overall efficiency in case of a hydro
power plant with expression.
OR
What are the different types of efficiency associated with a Hydro Power Plant? Show the
relation among them with expression.
Module IV
4. Differentiate between SI & CI engines.
5. Differentiate between 2 stroke and 4 stroke engines.
6. What are the advantages of 4 stroke engine over 2 stroke engines?
7. What are primary and secondary compression in a 2 stroke engine?
8. Explain the phases of refrigerant in high pressure and low pressure side of the compressor in a
Simple vapour compression cycle.
9. Why do condenser and evaporator units have coils of tubes?
10. What a boiler, what are its types?
11. Explain the function of any two boiler mounting and accessories.
12. Write any two of each thermodynamic, chemical and physical properties of ideal refrigerant?
Or What are the different required properties of an ideal refrigerant?
13. Discuss the advantages and disadvantages of a steam thermal power plant.
14. Draw the layout of an automobile transmission system showing all its components.
15. Explain in detail about the classification of brakes.
16. Draw a neat sketch of an internal expanding shoe brake showing all its components.
17. Write short notes on; a). Differential b). Gear box c). Propeller shaft d). Clutch
18. Distinguish between Radial Brake and Axial Brake.
Module V
19. Explain the terms used in robots: a). Brain/ controller b). Actuators c). Sensors d). End
effectors.
20. What are the various elements of a gating system?
21. What are the function of a runner and riser?
22. What are the function of Spruce and Spruce base well?
23. What are the functions of a good gating system?
24. Write short notes on: Bloom, Billet, Slab, Plate, Sheet and Strip.
25. Differentiate between Blanking & Punching.
26. Name any two materials that are used as sheet metal and write their applications

Long Answer Types


Module III
1. Explain the layout of a Hydro Power Plant with a neat sketch.
Module IV
2. Explain the construction and working of a 4 stroke SI engine with a neat sketch.
3. Explain the construction and working of a 2 stroke SI engine with a neat sketch.
4. Explain the construction and working of a Simple vapour compression refrigeration cycle
with a neat sketch.
5. Draw a layout of a steam power plant and explain its working.
6. Explain in brief different boiler mountings and accessories.
7. Explain the power transmission system of an automobile with a neat sketch.
8. Explain the construction and working of an Internal expanding shoe brake with a neat sketch.
Module V
9. Explain the various basic components of a robotic system with a neat sketch.
10. Explain different elements of a gating system used for casting with a neat diagram.
11. Explain the different specification of sheets according to their specified dimensions.

NB: These above question can be treated as important questions for Mid-sem as well as for semester examination.

You might also like