Scribd
Upload
15 views

C.rod 2

conneting rod

Uploaded by

Eka Sukanda Zaeni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views

C.rod 2

conneting rod

Uploaded by

Eka Sukanda Zaeni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Copyright 1991, 2011 Caterpillar Inc. All Rights Reserved.

Page 1 of 3

71J 955K TRACK LOADER Spesifikasi


Nomor Media SENR7590-01 Tanggal Publikasi 1981/10/01 Tanggal Pembaharuan 1995/09/16

Connecting Rod

(1) Bore in bearing for piston pin (new):

5S6360 Rod . . . 1.5017 ± .0003 in. (38.143 ± 0.008 mm)

5S2793 Rod . . . 1.7012 ± .0003 in. (43.210 ± 0.008 mm)

8N1984 Rod (tapered) . . . 1.5017 ± .0003 in. (38.143 ± 0.008 mm)

8N1721 Rod (tapered) . . . 1.7012 ± .0003 in. (43.210 ± 0.008 mm)

Maximum permissible clearance between bearing and piston pin (worn) . . . .003 in. (0.08 mm)

(2) Bore in connecting rod for bearing . . . 3.2500 ± .0005 in. (82.550 ± 0.013 mm)

(3) Distance between center of piston pin and center of crankshaft bearing (new) . . . 9.595 ± .001 in.
(243.71 ± 0.03 mm)

file://D:\SIS\TMP\sis231prt.html 2/25/2011
Copyright 1991, 2011 Caterpillar Inc. All Rights Reserved. Page 2 of 3

(4) Diameter of piston pin (new):

9H4016 Pin . . . 1.5003 ± .0002 in. (38.108 ± 0.005 mm)

7N9804 Pin . . . 1.5003 ± .0002 in. (38.108 ± 0.005 mm)

8M6487 Pin . . . 1.6998 ± .0002 in. (43.175 ± 0.005 mm)

7N9805 Pin . . . 1.6998 ± .0002 in. (43.175 ± 0.005 mm)

(5) Clearance between connecting rod bearing and crankshaft bearing surface (journal) . . . .0030
to .0066 in. (0.076 to 0.168 mm)

Maximum permissible clearance between bearing and crankshaft (worn) . . . .010 in. (0.25 mm)

(6) Torque on nut for connecting rod:

a. Put engine oil on threads and nut seat.

b. Tighten both nuts to . . . 30 ± 3 lb. ft. (40 ± 4 N·m)

c. Mark each nut and end of bolt.

d. Again tighten both nuts (from mark) . . . 90°

Install the connecting rod in the piston with the slot for the bearing tab on the same side as the V mark
on the piston.

Make reference to Special Instructions, Form No. GMG02394 and SMHS7366 for information about

file://D:\SIS\TMP\sis231prt.html 2/25/2011
Copyright 1991, 2011 Caterpillar Inc. All Rights Reserved. Page 3 of 3

checking and reconditioning connecting rods.

Copyright 1991, 2011 Caterpillar Inc.


All Rights Reserved.

file://D:\SIS\TMP\sis231prt.html 2/25/2011

You might also like