Project Name: Standby Hours: 24

Alarm Mins: 5
Installed By: Efficiency Factor: 20%
ARC-100
Battery & Voltage Drop Designed By: SLC Type: Class B
Calculations Date: NAC Source Voltage: 20.4

Model #: ARC-100 Max Panel Current (amps): 5

Panel ID:
User assumes all responsibility to ensure the quantities and current draw
Location: values in this worksheet are accurate prior to submittal.

Addressable Fire Panel Standby (amps) Alarm (amps)

Qty Part # Description Each Total Each Total
1 ARC-100 Analog Addressable FACP 0.130 0.130 0.220 0.220
Panel Standby: 0.130 Panel Alarm: 0.220

P-LINK (RS-485) Standby Alarm

UD-2000 / UD-1000 DACT Card 0.016 0.023
RA-6075/R LCD Annunciator 0.020 0.025
RA-6500 (R/F) Flush Mount LCD Annunciator 0.020 0.050
LED-16 (F) Flush Mount LED Annunciator 0.025 0.025
LED-16 (F)* LED Annunciator LED Power* 0.015 0.210
CA-6075 Class A Module 0.012 0.044
PSN-1000(E) Power Expander 0.015 0.015
PAD100-SLCE-127 SLC Expander 0.060 0.060
NOHMI-SLCE-127** SLC Expander 0.060 0.060
IDC-6 Initating Zone Expander 0.020 0.020
IDC-6 Initating Zone Expander Power* 0.030 0.270
RLY-5 Relay Expander 0.025 0.035
RLY-5 Relay Expander Power* 0.010 0.135
DRV-50 LED Driver Module 0.025 0.025
DRV-50 LED Driver Module LED Power* 0.010 0.215
FCB-1000 Fire Communications Bridge 0.025 0.025
FIB-1000 Fiber Interface Board 0.030 0.030
MC-1000 Multi-Connect Expander 0.010 0.010
SPG-1000 Serial Parallel Gateway 0.040 0.040
NCE-1000 Network Card Ethernet 0.050 0.050
NCF-1000 Network Card Fiber 0.095 0.095
**REQUIRED IF USING NOHMI PROTOCOL SLC DEVICES
(Maximum current draw on P-Link limited to 1 Amp) P-LINK Standby: 0.000 P-LINK Alarm: 0.000
*Only enter quantity if PLINK power is being used to power devices
SLC Devices Standby Alarm

AFC / ARC / IPA Series - PAD100/200

PAD-PD Analog Photo Smoke 0.000300 0.000300

PAD-PHD Analog Photo Smoke/Heat 0.000300 0.000300
PAD-HD Analog Fixed Temp Heat 0.000300 0.000300
PAD-CD Analog Carbon Monoxide Detector 0.000300 0.000300
PAD-PCD Analog Smoke/Carbon Monoxide Detector 0.000300 0.000300
PAD-PHCD Analog Smoke/Heat/Carbon Detector 0.000300 0.000300
PAD100-DRTS Duct Remote Test Switch 0.010000 0.015000
PAD-DUCT Addressable Duct Detector 0.000300 0.000300
PAD-DUCTR* Addressable Duct Detector w/Relay 0.000500 0.000500
PAD100-PSSA/PSDA Addressable Pull Station Single/Dual Action 0.000200 0.000200
PAD100-MIM Micro Input Module 0.000200 0.000200
PAD100-SIM Single Input Module 0.000240 0.000240
PAD100-DIM Dual Input Module 0.000240 0.000240
PAD100-RM Relay Module 0.000240 0.000240
PAD100-OROI One Relay One Input Module 0.000240 0.000240
PAD100-TRTI Two Relay Two Input Module 0.000240 0.000240
PAD100-ZM* Conventional Zone Module 0.000240 0.000240
PAD100-NAC* Notification Appliance Circuit 0.000200 0.000200
PAD100-SM Speaker Module 0.000200 0.000200
PAD100-IM Isolator Module 0.000150 0.000150
PAD100-LED LED Module 0.000240 0.000240
PAD100-LEDK Addressable LED w/ Key Switch 0.000200 0.000200
PAD100-SB*** Addressable Sounder Base 0.000200 0.000200
PAD100-LFSB*** Addressable Low Frequency Sounder Base 0.000200 0.000200
PAD100-RB* Addressable Relay Base 0.000200 0.000200
PAD100-IB Addressable Isolator Base 0.000150 0.000150

Potter Electric Signal (C)2022 1 of 5 ARC-100 Battery and Voltage Drop Calculation
 AFC / ARC / IPA Series - PAD300

PAD300-PD Analog Photo Smoke 0.000300 0.000300

PAD300-PD-I Analog Photo Smoke W/ Isolator 0.000300 0.000300
PAD300-PHD Analog Photo Smoke/Heat 0.000300 0.000300
PAD300-PHD-I Analog Photo Smoke/Heat/Isolater 0.000300 0.000300
PAD300-HD Analog Fixed Temp Heat 0.000300 0.000300
PAD300-HD-I Analog Fixed Temp Heat W/ Isolator 0.000300 0.000300
PAD300-CD Analog CO2 Detector 0.000300 0.000300
PAD300-CD-I Analog CO2 Detector W/Isolater 0.000300 0.000300
PAD300-PCD-I Analog Smoke/CO2 Detector 0.000300 0.000300
PAD300-PCD Analog Smoke/CO2 Detector W/Isolater 0.000300 0.000300
PAD300-PHCD Analog Smoke/Heat/CO2 Detector 0.000300 0.000300
PAD300-PHCD-I Analog Smoke/Heat/CO2 Detector W/ Isolater 0.000300 0.000300
PAD300-DD Addressable Duct Detector 0.000300 0.000300
PAD300-SB*** Addressable Sounder Base 0.000200 0.000200
PAD300-LFSB*** Addressable Low Frequency Sounder Base 0.000200 0.000200
PAD300-RB* Addressable Relay Base 0.000200 0.000200
PAD300-IB Addressable Isolator Base 0.000150 0.000150
PFC-6000 / P Series

PSA Analog Photo Smoke 0.000325 0.000325

PSHA Analog Photo Smoke/Heat 0.000325 0.000325
RHA Analog Rate of Rise Heat 0.000325 0.000325
FHA Analog Fixed Temp Heat 0.000325 0.000325
DDA Addressable Duct Detector 0.000325 0.000325
APS-SA/APS-DA Addressable Pull Station Single/Dual Action 0.000325 0.000325
MCM Mini Contact Input Module 0.000325 0.000325
SCM-4 Single Contact Input Module 0.000325 0.001000
DCM-4 Dual Contact Input Module 0.000325 0.001000
TRM-4 Twin Relay Output Module 0.000325 0.001000
CIZM-4 * Conventional Zone Input Mod 0.000325 0.001000
MOM-4 * Monitored Output Module 0.000325 0.001000
ARB * Detector Base w/Relay 0.000325 0.000325
ASB * Detector Base w/Sounder 0.000325 0.000325
SCI ** Short Circuit Isolator (Class A) 0.000325 0.002340
AIB ** Detector Base w/Isolator (Class A) 0.000325 0.002340
IM/IB/SCI/AIB Class B ** Current Draw from Install Manual

1 SLC Loop Alarm LED Current 0.000000 0.000000 0.036000 0.036000

* Requires Aux Power (Configure Below) SLC Standby: 0.000000 SLC Alarm: 0.036000
**
See the installation manual for special considerations when installing IM, IB, AIB, SCI
devices on Class B loops.
*** Requires Aux Sounder Base Power (Configure Below)
NAC Circuits (See NAC Configuration below) Standby (amps) Alarm (amps)
Ckt Use Description Total Total
1 0.00000 0.00000
2 0.00000 0.00000
NAC Standby: 0.00000 NAC Alarm: 0.00000
I/O Circuits (See I/O Configuration below) Standby (amps) Alarm (amps)
Ckt Use Description Total Total
1 0.00000 0.00000
2 0.00000 0.00000
I/O Standby: 0.00000 I/O Alarm: 0.00000

Battery Calculation Summary Standby (amps) Alarm (amps)

Panel Current: 0.13000 0.22000
P-Link Current: 0.00000 0.00000
SLC Device Current: 0.00000 0.03600
NAC Circuit Current: 0.00000 0.00000
I/O Circuit Current: 0.00000 0.00000
SLC Loop Type: Class B Total Standby: 0.130000 Total Alarm: 0.25600
Device Addresses Used 0 Standby Hours: 24 Alarm Mins: 5
Device Addresses Available: 100 AH Required: 3.12 AH Required: 0.03
Total Combined Standby & Alarm AmpHours Required: 3.15
5 Efficiency Factor: 20%
Required Battery AmpHours: 3.78
Battery AmpHours Provided:
Note: The cabinet will house two 8 AH or 18 AH batteries. The charging circuit is rated for up to
two 55 AH batteries.

Potter Electric Signal (C)2022 2 of 5 ARC-100 Battery and Voltage Drop Calculation
 Note: The cabinet will house two 8 AH or 18 AH batteries. The charging circuit is rated for up to
two 55 AH batteries.

NAC Circuit Configuration & Voltage Drop

NAC 1 MAX Circuit Current (amps): 3 Source Voltage Used (VDC): 20.4

Usage: Description:

Wire Type Ohms/1000ft Length 1-Way Actual Ohms Max Load (amps) Volts @ EOL Min Volts Req'd
#12 Solid 2.01 0.000 0.000 20.40 16

Circuit Devices Standby (amps) Alarm (amps)

Qty Lookup Type Description Each Total Each Total

User can add devices on the fly

to these bottom 5 rows
(No lookup function)

Total Standby: 0.00000 Total Alarm: 0.00000

NAC 2 MAX Circuit Current (amps): 3 Source Voltage Used (VDC): 20.4

Usage: Description:

Wire Type Ohms/1000ft Length 1-Way Actual Ohms Max Load (amps) Volts @ EOL Min Volts Req'd
#12 Solid 2.01 0.000 0.000 20.40 16

Circuit Devices Standby (amps) Alarm (amps)

Qty Lookup Type Description Each Total Each Total

User can add devices on the fly

to these bottom 5 rows
(No lookup function)

Total Standby: 0.00000 Total Alarm: 0.00000

I/O Circuit Configuration & Voltage Drop

I/O 1 MAX Circuit Current (amps): 1 Source Voltage Used (VDC): 20.4

Usage: Description:

Wire Type Ohms/1000ft Length 1-Way Actual Ohms Max Load (amps) Volts @ EOL Min Volts Req'd
#12 Solid 2.01 0.000 0.000 20.40 16

Circuit Devices Standby (amps) Alarm (amps)

Qty Lookup Type Description Each Total Each Total

User can add devices on the fly

to these bottom rows
(No lookup function)
Total Standby: 0.00000 Total Alarm: 0.00000

I/O 2 MAX Circuit Current (amps): 1 Source Voltage Used (VDC): 20.4

Usage: Description:

Wire Type Ohms/1000ft Length 1-Way Actual Ohms Max Load (amps) Volts @ EOL Min Volts Req'd
#12 Solid 2.01 0.000 0.000 20.40 16

Circuit Devices Standby (amps) Alarm (amps)

Qty Lookup Type Description Each Total Each Total

User can add devices on the fly

to these bottom rows
(No lookup function)
Total Standby: 0.00000 Total Alarm: 0.00000

Potter Electric Signal (C)2022 3 of 5 ARC-100 Battery and Voltage Drop Calculation
 User Defined Parts

Description Standby Alarm

User Defined 1
User Defined 2
User Defined 3
User Defined 4
User Defined 5
User Defined 6
User Defined 7
User Defined 8
User Defined 9
User Defined 10
User Defined 11
User Defined 12
User Defined 13
User Defined 14
User Defined 15
User Defined 16
User Defined 17
User Defined 18
User Defined 19
User Defined 20
User Defined 21
User Defined 22
User Defined 23
User Defined 24
User Defined 25
User Defined 26
User Defined 27
User Defined 28
User Defined 29
User Defined 30
User Defined 31
User Defined 32
User Defined 33
User Defined 34
User Defined 35
User Defined 36
User Defined 37
User Defined 38
User Defined 39
User Defined 40
User Defined 41
User Defined 42
User Defined 43
User Defined 44
User Defined 45
User Defined 46
User Defined 47
User Defined 48
User Defined 49
User Defined 50
User Defined 51
User Defined 52
User Defined 53
User Defined 54
User Defined 55
User Defined 56
User Defined 57
User Defined 58
User Defined 59
User Defined 60
User Defined 61
User Defined 62
User Defined 63
User Defined 64
User Defined 65
User Defined 66
User Defined 67
User Defined 68
User Defined 69
User Defined 70
User Defined 71
User Defined 72
User Defined 73
User Defined 74
User Defined 75
User Defined 76
User Defined 77
User Defined 78
User Defined 79
User Defined 80
User Defined 81
User Defined 82
User Defined 83
User Defined 84
User Defined 85
User Defined 86
User Defined 87
User Defined 88
User Defined 89
User Defined 90
User Defined 91
User Defined 92
User Defined 93
User Defined 94
User Defined 95
User Defined 96
User Defined 97
User Defined 98
User Defined 99
User Defined 100