Scribd
Upload
22 views2 pages

Installation Guide 49653

Uploaded by

marina.kozina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
22 views2 pages

Installation Guide 49653

Uploaded by

marina.kozina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INSTALLATION INSTRUCTIONS

UNDERCOUNTER SINKS
Rectangular/Square Models: 0426, 0610, 0614, 0615, & 0618

Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help
ensure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review
the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Observe Local Plumbing and Building Codes.

Recommended Tools & Materials

Adjustable Wrench

Drill
Putty Knife Plumbers' Putty

Basin Wrench
Channel Lock Pliers Saber Saw

Regular Screwdriver

10'
Silicone Adhesive

Tape
Measure Pipe Wrench Phillips Screwdriver Hacksaw
Tubing Cutter

NOTE: More specialized tools may be necessary to install this sink to countertop materials other than wood or wood composites.

1 3 FOR WOOD COUNTERTOP


NOTE: To avoid damage to
countertop, install sink such that Mark and pre-drill the wood screw holes as located on the
future removal from underneath the enclosed template. Waterproof any exposed areas of wood.
countertop is possible.

First, make sure the clearance


between the backsplash, faucet,
fixtures and cabinets are 3/4 MIN.
acceptable for the new sink.

For Model 0426 to be ADA Clip


compliant the sink must be installed
with the overflow in the rear.
Drill 1/8 dia. X 3/8 deep
#10 Wood Screw

2 Carefully cut out the enclosed template, then position and trace the 4 FOR MARBLE OR SOLID SURFACE COUNTERTOP
template on the countertop as shown on the template. Make a mark of
the faucet hole centerline on the countertop. Drill a 1/2" pilot hole on To protect countertop, place it on a foam padding and drill
the inside of the cut line. Use a saber saw or a keyhole saw to cut out 3/8 Dia. X 1/2 deep hole as per location shown on template.
the countertop opening.

Brass insert, epoxy in place


with threaded end exposed.
(Epoxy not supplied.)
Perimeter of Sink
3/4 MIN.

Cutout Clip

#10-24
Machine screw

Product names listed herein are trademarks of AS America, Inc. unless otherwise noted. 730555-100 Rev. C
© AS America, Inc. 2009
5 8

Install faucet (not included) and countertop (not


included) following manufacturers instructions.
Mount the drain assembly (not included) on the sink,
following faucet manufacturer's instructions. Be
certain to apply a bead of sealing putty on the
underside of the drain (Part "A") in order to ensure a
watertight seal between the sink and drain. Remove
excess putty after installing drain on sink.

6 9
NOTE: Do not use adhesives or adhesive sealants.
After checking fit and alignment of sink to cut out,
apply a bead of silicone adhesive to rim of sink.

Shut-Off
Valves

Connect supply line to faucet (finger tight) and carefully bend


tubes to engage with the supply shut-off valves. Tighten
connections at faucet and shut-off valves for water tight seal.

7 10
Center bowl over cutout Connect trap to drain
and tighten screws (see 3 assembly hand tight to check
or 4) to secure bowl to alignment. It may be
countertop. Remove necessary to cut off part of
excess sealant from the tailpiece (area "B") or part
inside lip. of the horizontal leg of the
C
trap (area "C"). Secure joints B
NOTE: The screws
for watertight assembly.
provided should be used
on countertops with a
minimum 1" thickness.
For thinner countertops,
use appropriate anchors
and fasteners.

In the United States: In Canada: In Mexico:


American Standard Brands AS Canada ULC Customer Service Manager
P.O. Box 6820 2480 Stanfield Rd. AS Maquila, S.A. de C.V.
Piscataway, New Jersey 08855 Mississauga, Ontario Via Morelos #330
Attention: Director of Consumer Affairs Canada L4Y 1S2 Col. Santa Clara
Ecatepec 55540 Edo. Mexico
For residents of the United States, warranty Toll Free: (800) 387-0369 www.americanstandard.com.mx
information may also be obtained by calling the www.americanstandard.ca
following toll free number: (800) 442-1902
www.americanstandard-us.com

730555-100 Rev. C

You might also like