Chapter - II

CONCRETE WORKS
- The rates are excluding the cost of steel and formwork.
- Percentage as per Appendix-I to be adopted in case formwork is
considered.

13 14
 CHAPTER 2 Item Description of Item Unit Rate Rs.
No.
CONCRETE WORKS 2.2.3.2 M30 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,559.00
aggregates with 20% partial replacement with Recycled concrete
(PLAIN & REINFORCED CEMENT CONCRETE) aggregate (RCA)
Item Description of Item 2.2.4.1 M35 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,917.00
Unit Rate Rs.
No. aggregates
2.1 Providing and laying in position plain cement concrete for levelling
course for all works in foundation. The granite/trap/basalt crushed 2.2.4.2 M35 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,842.00
graded coarse aggregates and fine aggregates as per relevant IS aggregates with 20% partial replacement with Recycled concrete
Codes machine mixed, laid in layers not exceeding 150 mm thickness, aggregate (RCA)
well compacted using plate vibrators, including all lead & lifts, cost of 2.2.5.1 M 40 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,200.00
all materials of quality, labour, Usage charges of machineries, curing, aggregates
and all the other appurtenances required to complete the work as per
technical specifications. (The cost of steel reinforcement & formwork 2.2.5.2 M40 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,126.00
shall be paid separately) aggregates with 20% partial replacement with Recycled concrete
2.1.1 Mix 1:5:10 Using 40 mm nominal size graded crushed coarse m³ 4,976.00 aggregate (RCA)
aggregates
2.3 Providing and laying in Reinforced cement concrete for all Basement
2.1.2 Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse m³ 5,364.00 & surface level works, return walls, retaining walls, sunken floors
aggregates etc. The granite/trap/basalt crushed graded coarse aggregates and
fine aggregates as per relevant IS Codes machine mixed with super
2.1.3 Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse m³ 5,752.00 plasticisers, laid in layers, well compacted using needle vibrators,
aggregates providing weep holes wherever necesary, including all lead & lifts, cost
2.1.4 Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse m³ 5,926.00 of all materials of quality, labour, Usage charges of machinery, curing
aggregates and all other appurtenances required to complete the work as per
technical specifications. (The cost of steel reinforcement & formwork
2.2 Providing and laying in position Reinforced cement concrete for all to be paid separately)
Foundation works. The granite/trap/basalt crushed graded coarse
aggregates and fine aggregates as per relevant IS Codes machine 2.3.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,256.00
mixed with super plasticizers laid in finished layers, well compacted aggregates
using needle vibrators, including all lead & lifts, cost of all materials, 2.3.2 M25 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,288.00
quality confirming to the requirements of relevant IS codes , labour, aggregates
Usage charges of machinery, curing and all the other appurtenances
required to complete the work as per technical specifications. (The cost 2.3.3 M30 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,714.00
of steel reinforcement & formwork to be paid separately) aggregates

2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,231.00 2.3.4 M 35 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,117.00
aggregates aggregates

2.2.1.2 M20 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,161.00 2.3.5 M 40 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,408.00
aggregates with 20% partial replacement with Recycled concrete aggregates
aggregate (RCA)
2.4 Providing and laying in position Reinforced cement concrete for all
2.2.2.1 M25 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,285.00 Sub structures of building, Irrigation works, Sub structure works of
aggregates bridges, Drain works & other parallel works from 0.50m to 3.50 m
height. The granite/trap/basalt crushed graded coarse aggregates and
2.2.2.2 M25 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,211.00 fine aggregates as per relevant IS Codes machine mixed with super
aggregates with 20% partial replacement with Recycled concrete plasticisers, laid in layers, well compacted using needle vibrators,
aggregate (RCA) providing weep holes wherever necesary, including all lead & lifts, cost
2.2.3.1 M30 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,633.00 of all materials of quality, confirming to the requirements of relevant
aggregates IS codes, labour, Usage charges of machinery, curing and all other

15 16
 Item Description of Item Item Description of Item
Unit Rate Rs. Unit Rate Rs.
No. No.
appurtenances required to complete the work as per technical 2.5.5 M 40 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,608.00
specifications. (The cost of steel reinforcement & formwork to be paid aggregates
separately)
2.5.6 M50 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,122.00
2.4.1 Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse m³ 6,096.00 aggregates
aggregates
2.5.7 M 55 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,122.00
2.4.2 M20 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,256.00 aggregates
aggregates
2.6 Bridge works
2.4.3 M25 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,299.00
aggregates 2.6.1 For Height upto 5 m rates, adopt as per item no 2.5.3 to 2.5.7

2.4.4 M30 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,819.00 2.6.2 beyond 0 m upto 5 m add 10 % extra on formwork for staging & base
aggregates preparation

2.4.5 M35 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,176.00 2.6.3 beyond 5 m upto 10 m add 12% extra on formwork for staging & base
aggregates preparation

2.4.6 M40 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,423.00 2.6.4 beyond 10 m upto 15 m add 14% extra on formwork for staging & base
aggregates preparation

2.4.7 M45 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,934.00 2.6.5 beyond 15 m upto 20 m add 16% extra on formwork for staging & base
aggregates preparation

2.4.8 M50 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,297.00 2.6.6 beyond 20 m upto 25 m add 18% extra on formwork for staging & base
aggregates preparation

2.4.9 M55 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,297.00 2.6.7 beyond 25 m add 20% extra on formwork for staging & base preparation
aggregates 2.7 Providing waterproofing & durability enhancing admixture with approval kg 292.00
2.5 Providing and laying in position Reinforced cement concrete for all from MORT&H for use on road & bridge projects with IRC accreditation
Super structures of building , Road works, Water works, Irrigation works & shall possess CE approval as per EN934-2. Material must fulfil the
& super structure works of bridges upto 3.50 m height. The granite/ requirements of ACI-212-3R-10 Chapter 15 and fall under PRAH
trap/basalt crushed graded coarse aggregates and fine aggregates (permeability reducing admixtures for hydrostatic conditions) and must
as per relevant IS Codes machine mixed with super plasticisers laid in reduce coefficient of permeability of concrete by more than 90% when
layers, well compacted using needle vibrators. The cost includes all compared to control concrete and tested as per DIN 1048 Part-5 by
lead & lifts, cost of all materials, quality confirming to the requirements carrying out 4 cycles each of 5 bar hydrostatic pressure for 72 hours
of relevant IS codes , labour, Usage charges of machinery, curing and and drying for 48 hours between the cycle and coefficient of permeability
all other appurtenances required to complete the work as per technical calculated as per Darcy’s formula / Valenta equation by incorporating
specifications. (The cost of steel reinforcement, dowel bars & formwork penetration values obtained at the end of fourth cycle pressure as per
to be paid separately) DIN 1048 test. Material must reduce chloride diffusion coefficient by
minimum 45% when tested as per ASTM C 1556-4 and compared
2.5.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,471.00 with the control concrete, thereby prolonging the durability and service
aggregates of life of the treated concrete structure as well as must demonstrate
minimum reduction of 50% in shrinkage cracks as compared to control
2.5.2 M25 Design Mix Using 20 mm nominal size graded crushed coarse m³ 6,492.00 concrete, as per BS ISO-1920-8:2009. Must demonstrate no internal
aggregates expansion under sulphate attack, when tested as per ASTM C-1012-
2.5.3 M30 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,022.00 12 & conforming to norms of EPD as per ISO 14025 & EN 15804-A1.
aggregates The crystalline admixture treated concrete must be able to withstand
high hydrostatic pressure of 16 bar (156 m of water head) when tested
2.5.4 M 35 Design Mix Using 20 mm nominal size graded crushed coarse m³ 7,305.00 as per DIN 1048 & must capable of self -healing of cracks up to width
aggregates of 0.5 mm. The performance of the crystalline admixture must not be
restricted by water / cement ratio of the concrete mix. In other words,

17 18
 Item Description of Item
3. The Cement constants considered in the analysis is for case OPC. However, if GGBS or any
Unit Rate Rs.
No. other mineral additives and admixtures as per MoRTH section 1700 are used, necessary
the crystalline admixture must perform at any water / cement ratio of deductions in the cost of the concrete with approved mix designs as per IS-456:2000
the concrete mix. Product must possess a third party assurance, such
as a U sign certificate or similar, confirming that the product, when use shall be made by the sanctioning authorities.
in the concrete, will have no detrimental side effects in terms of Alkali
4. The usage charges for machinery means the cost inclusive of operating charges. i.e
Silica Reaction (ASR), corrosion of steel reinforcement etc., as per the
requirements of DIN 18998. The Dosage should be at 0.8% by weight separate cost for crew & fuel shall not be paid unless specified in extra ordinary cases.
of cement + cementitious material (or such dosage as desired to meet
durability criteria) as per technical specification.
5. Additionalities For Building works

2.8 Supply and placing the Design Mix of M-30 Grade for Self Compacting  1% of the finished cost of concrete shall be paid extra for every subsequent floors.
Concrete corresponding to IS 456 and relevant IS codes using Batching
plant, Transit mixer and concrete pump with 12.5 mm size graded
 5% of the finished cost of concrete shall be paid extra for concreting in foul
machine crushed hard metal (coarse aggregate) from approved quarry conditions.
including cost and conveyance of all materials like cement, cement
substitutes like fly ash, GGBS, etc., fine aggregate (sand), coarse  5% of the finished cost of concrete shall be paid extra for concreting in under water
aggregate, Admixture, water etc., to site inclduding and sales and other conditions.
taxes on all materials including all opertational incidental and labour
charges, but excluding cost of steel and its fabrication & formwork 6. The concrete pumps considered in the analysis is the 'Line pump' whereas separate
charges for finished item of work with minimum cement content as per provisions shall be made if the pumping is done through 'Boom placer' which involves
IS code including pumping & curing etc complete for finished item of
additional costs.
work (RCC slabs, Beams, Columns, Lintels, Water Tanks, RCC Walls
in Buildings). 7. The vibrators for concrete used shall conform to IS 3558 (1983) reffirmed 2004.
2.8.1 Upto 5m height m³ 7,874.00
8. The height of the Buidling shall be considered as 3.6 m per floor as per NBC 2016 for
2.8.2 Add extra 3% on form work for staging for 0 to 5 m calculation of lifts.
2.8.3 Add extra 5% on form work for staging for 5 to 10 m 9. The finished cost of concrete is exclusive of Steel (Re-inforcement) & formwork charges.
2.8.4 Add extra 5 % on form work for staging beyond 10 m
10. Necessary over head charges shall be add for Bridge works as per table below :
2.9 Applying stamping finish on M30 grade concrete on PCC sub grade, m2 407.00
applying and finishing with stamp/stencil of approved pattern and color
Bridge Works
in accordance with Engineers instructions & approved drawings with
use of any approved brand of color hardener of 4.5 kg/m2, including For Bridge works, following additional overhead charges to be considered in the rate
floating of color hardener over the concrete surface with different types
of floaters, application of release agent of 0.12 to 0.13kg/m2 depending analysis.
on matching combination of selected color, stamping over the concrete
Sl.
surface with stamping tools , cleaning of surface with water and groove Description Overhead charges to be considered
cutting of finished concrete and application of acrylic based sealer for No.
final finish. Coverage of sealer should be 0.30litre/m2 per coat. The 1. Minor Bridges 20%
cost is inclusive of manpower, cutting machine, sprayer and all tools
tackles for all activities and complete smooth and finish as per technical 2. Bridge Works (Rehabilitation) 30%
specifications. (The cost of Concrete shall be paid separately)
3. Tunnel Works 25%
Note :
1. The cost of concrete is inclusive of lead but exclusive of lift.
2. The Concrete shall be used in works from ISO accredited Batching plants.

19 20