Universal 2 Channel Receiver

Model 8002E
SPECIFICATIONS
DISCONNECT POWER TO GARAGE Output Rating ......................................I max. = 5 A; V max. = 30V AC/DC
Power input <24V .................................................9-16V AC, @ 30 mA
DOOR OPENER BEFORE INSTALLING ...................................................................................9-24V DC, @ 30 mA
RECEIVER. .................................................................................16-30V AC, @ 30 mA
>24V ................................................24-30V DC,@ 30 mA
For use with the following RF modules: RF Frequency ...........................................................418MHz, 433.92MHz
To operate the control board via radio, a radio module
must first be installed in slots CN1/CN2.
TO SET OUTPUT DURATION
• 801221 Superheterodyne, 433.92MHz The receiver can be set for either constant or momentary closure on the
• 801344 Superregenerative, 418MHz output contacts for each channel (A and B). (Use constant closure only if
constant pressure is needed.) With the jumper in “1” (Momentary) position,
The 2 Channel Universal Receiver Model 8002E can
the contacts will close for 150ms regardless of the length of radio
be programmed to receive up to 15 codes for each
transmission. With the jumper in “2” (Constant) position, the contacts will
channel.
stay closed as long as the radio continues transmitting.
Receiver
INSTALLATION
The receiver should be mounted towards the front of the garage, preferably
about two meters above the floor. Select a location which allows clearance
for opening the cover, and space for the antenna (as far from metal Momentary Constant signal
structures as possible). The receiver and antenna use TV Type F coaxial (Hold to run)
connectors. The antenna is threaded directly onto the receiver. An additional
cable extension (86LM) is available to improve the range
The transformer (Model 23009E) must be plugged into the wall within two Antenna Connection
meters of the receiver, to allow the wire to reach the receiver terminals.
1. Fasten the receiver securely with screws through the corner holes which
are located under the cover.
optional
2. AC/DC are the terminals on the circuit board. (see illustration)
Indicator lights
Connect the transformer wire to the terminals.Now tighten (momentary or constant) Ant.
terminals.
LDS2 CN1
3. Connect operator control board to the terminals of the Universal LDS1

Receiver. In this process, connect the cable of te wall-button to terminals Indicator lights
(Channel A & B)
(Channel A). Connect the cable of the second wall-button ( if you have to CN2

operate 2 doors) to the terminals . (Channel B). In case there is no wall- A B Command buttons
LDS3 LDS4
(Channel A & B)
button or keyswitch, consult the manual of your garage door opener. Jumper
Channel B Program buttons
4. Plug in the transformer and reconnect power. You may use the Test Test (Channel A & B )
Test button to operate your opener(s).
LearnA LearnB Jumper
Channel A
PROGRAMMING THE RECEIVER TO ACCEPT
YOUR TRANSMITTER CODE < 24V >24V
Input
Activate the opener only when door is in full view, free of OUT A OUT B AC / DC
Transformer
obstruction and properly adjusted. No one should enter or
leave garage while door is in motion. Do not allow children to
operate push button(s) or remote(s). Do not allow children to
play near the door.
1. Press and hold the remote control push button.
2. Press and release the Learn button in the Control Center on the opener
panel. The indicator light will flash once.
3. Release the remote push button.
Now the opener will operate when the remote control push button is < 24V > 24V
9-16V AC, @ 30mA 16-30V AC, @ 30mA
pressed. 9-24V DC, @ 30mA 24-30V DC, @ 30mA

If you release the remote control push button before the indicator
lights flash, the opener will not accept the code.
Repeat steps 1 – 3 to program the receiver for all remote controls in use for
that door. If a second door is in use, use a different remote control button
and repeat the steps for channel B.
Replace top cover with mounting screws.
To erase all codes from the receiver: hold the receiver’s Learn button until
the indicator light goes off (after 6 seconds). All codes that the receiver has
learned will be erased.

114A2460C-GB