Scribd
Upload
22 views

Design and Drawing of RC Structure

Uploaded by

OMAR MUKTHAR JAMAL MOHAMED
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
22 views

Design and Drawing of RC Structure

Uploaded by

OMAR MUKTHAR JAMAL MOHAMED
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

INTERNATIONAL INSTITUTE OF MANAGEMENT AND

TECHNICAL STUDIES
Design and Drawing of RC Structure
Note - IS-456:2000 and SP-16 is allowed.

Q.1 Objective type multiple choice questions (10 questions @ 2 mark) 20

i. Select the incorrect statement


A) R.C.C has better fire resistance than steel
B) R.C.C. structure is economical than steel structure
C) Strength of concrete decreases as age increases
D) R.C.C can be used for under water and marine structures

ii. As per IS. 456-2000, Minimum grade of concrete for R.C.C. should be
A) M10
B) M15
C) M20
D) M25

iii. Specific weight of Reinforced cement concrete is


A) 25 N/mm3
B) 25 kN/mm3
C) 25 N/m3
D) 25 kN/m3

iv. As per IS: 456-2000, the maximum size of aggregate is


A) 1/4 of maximum thickness of member
B) 1/4 of minimum thickness of member
C) 1/5 of maximum thickness of member
D) 1/5 of minimum thickness of member

v. Side face reinforcement is provided when the depth of beam exceeds


A) 250 mm
B) 450 mm
C) 550 mm
D) 750 mm

vi. If depth of actual neutral axis is greater than depth of critical neutral axis, then
A) Concrete attains its permissible stress earlier
B) Steel attains its permissible stress earlier
C) Both concrete and steel reaches its permissible stresses simultaneously
D) None of the above
vii. Mat is a shallow foundation supporting
A) number of columns in one row
B) only one column
C) number of columns in more than one row
D) piles

viii. The anchorage value of the hook for a mild steel bar is generally considered as
A) 8 Ф
B) 16 Ф
C) 32 Ф
D) 48 Ф

ix. Limit state of collapse deals with


A) strength and stability of the structure
B) durability
C) conditions such as deflection, cracking
D) all the above

x. The ultimate average anchorage bond stress for plain bars in tension for the M20
grade of concrete is
A) 1.60 N/mm2
B) 1.92 N/mm2
C) 2.24 N/mm2
D) 2.40 N/mm2

Q.2 Design a RCC beam of rectangular section using the following data- 16
Effective span = 8m, imposed load = 30kN/m, b = 300mm, d=600mm, cover =
50mm, M20 grade of concrete and Fe415 grade of steel. Draw the neat sketch of
reinforcement detailing.

Q.3 Design a cantilever beam for flexure and shear to suit the following data- 16
Clear span = 2.5m, live load = 20kN/m, cantilever beam is monolithic with R.C.
column 300 mm wide and 450 mm deep, Fe415 grade of steel and M20 grade of
concrete. Also design the anchorage length at the support. Draw the neat sketch of
reinforcement detailing.

Q.4 Design the reinforcement to be provided in the short column of Figure is subjected 16
to Pu = 2000 kN, Mux = 130 kNm (about the major principal axis) and Muy = 120
kNm (about the minor principal axis). The unsupported length of the column is 3.2
m, width b = 400 mm and depth D = 500 mm. Use M 25 and Fe
415 for the design.Draw the neat sketch of reinforcement detailing.

Q.5 Design a two way slab for a room of size 4mx5m with discontinuous and simply 16
supported edges on all the sides with corners prevented from lifting to support a
live load of 4kN/m2 adopt M20 grade of concrete and Fe415 grade of steel. Draw
the neat sketch of reinforcement detailing.
Q.6 Design a footing for a 500 x 350 mm column using 20 mm bars as dowels to 16
transmit characteristic load of 600 kN as dead load and 400 kN as live loas to a
foundation with safe bearing capacity of 120 kN/m2. Assume M20 grade of
concrete and Fe415 grade of steel.

Guideline –

• Ensure to solve every question in series.

• Do not copy past answers, as it will lead to rejection of answer sheets.

• Make sure to write enough length answers of descriptive questions as per the weightage.

• Highlight more relevant case studies and practice examples.

• Submit answer sheet in standard format only.

• Make sure to be in time limits of submission to avoid rejection of submission after deadline.

• In case of hand written sheet submission please be assure of sober writing and cleanliness of answer
sheet.

• Do take care of numerical and diagrammatical representation up to the mark if applicable.

You might also like