Safety and Reference

Please read this manual carefully before operating your TV and retain
it for future reference.
OLED77C8PUA OLED65B8PUA OLED55B8PUA
OLED65B8SUC OLED55B8SUC
OLED65C8PUA OLED55C8PUA
OLED65C8AUA OLED55C8AUA
OLED65E8PUA OLED55E8PUA

*MFL70301502* www.lg.com
(1806-REV03) Copyright ⓒ 2018 LG Electronics Inc. All Rights Reserved.
Printed in Korea
 Important Safety Instruction
•• Read these instructions.
•• Keep these instructions.
ENGLISH

•• Heed all warnings.

•• Follow all instructions.
•• Do not use this apparatus near water.
•• Clean only with dry cloth.
•• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
•• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
•• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
•• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
•• Only use attachments/accessories specified by the manufacturer.
•• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.

•• Unplug this apparatus during lightning storms or when unused for long periods of time.
•• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

By using this product, you agree that all disputes between you and LG arising out of or relating in any way to this product (including but not
limited to warranty disputes) shall be resolved exclusively through binding arbitration on an individual basis. The terms of the arbitration
agreement (including details on the procedure for resolving disputes) is available at www.lg.com/us/arbitration (USA) or www.lg.ca/arbitration
(Canada).
2
Warning! Safety Instructions •• Ventilation
-- Install your TV where there is proper ventilation. Do not install in
a confined space such as a bookcase.
-- Do not install the product on a carpet or cushion.
-- Do not block or cover the product with cloth or other materials
CAUTION

ENGLISH
while unit is plugged in.
RISK OF ELECTRIC SHOCK •• Take care not to touch the ventilation openings. When watching
DO NOT OPEN the TV for a long period, the ventilation openings may become hot.
•• Protect the power cord from physical or mechanical abuse, such as
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT being twisted, kinked, pinched, closed in a door, or walked upon.
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. Pay particular attention to plugs, wall outlets, and the point where
REFER TO QUALIFIED SERVICE PERSONNEL. the cord exits the device.
The symbol is intended to alert the user to the presence of •• Do not move the TV whilst the Power cord is plugged in.
uninsulated dangerous voltage within the product’s •• Do not use a damaged or loosely fitting power cord.
enclosure that may be of sufficient magnitude to constitute a risk
•• Be sure do grasp the plug when unplugging the power cord. Do
of electric shock to persons.
not pull on the power cord to unplug the TV.
The symbol is intended to alert the user to the presence of •• Do not connect too many devices to the same AC power outlet as
important operating and maintenance (servicing) this could result in fire or electric shock.
instructions in the literature accompanying the device.
•• Disconnecting the Device from the Main Power
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, -- The power plug is the disconnecting device. In case of an
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. emergency, the power plug must remain readily accessible.
•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS •• Do not let your children climb or cling onto the TV. Otherwise, the
WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. TV may fall over, which may cause serious injury.
•• Do not place the TV and/or remote control in the following •• Outdoor Antenna Grounding (Can differ by country):
environments: -- If an outdoor antenna is installed, follow the precautions below.
-- Keep the product away from direct sunlight. An outdoor antenna system should not be located in the vicinity
-- An area with high humidity such as a bathroom of overhead power lines or other electric light or power circuits,
-- Near any heat source such as stoves and other devices that or where it can come in contact with such power lines or circuits
produce heat. as death or serious injury can occur.
-- Near kitchen counters or humidifiers where they can easily be Be sure the antenna system is grounded to provide some
exposed to steam or oil. protection against voltage surges and built-up static charges.
-- An area exposed to rain or wind. Section 810 of the National Electrical Code (NEC) in the U.S.A.
-- Do not expose to dripping or splashing and do not place objects provides information with respect to proper grounding of the
filled with liquids, such as vases, cups, etc. on or over the mast and supporting structure, grounding of the lead-in wire
apparatus (e.g., on shelves above the unit). to an antenna discharge unit, size of grounding conductors,
-- Near flammable objects such as gasoline or candles, or expose location of antenna discharge unit, connection to grounding
the TV to direct air conditioning. electrodes and requirements for the grounding electrode.
-- Do not install in excessively dusty places. Antenna grounding according to the National Electrical Code,
Otherwise, this may result in fire, electric shock, combustion/ ANSI/NFPA 70
explosion, malfunction or product deformation.

3
 •• Grounding (Except for devices which are not grounded.) •• Batteries
-- TV with a three-prong grounded AC plug must be connected to -- Store the accessories (battery, etc.) in a safe location out of the
a three-prong grounded AC outlet. Ensure that you connect the reach of children.
earth ground wire to prevent possible electric shock. -- Do not short circuit, disassemble, or allow the batteries to
•• Never touch this apparatus or antenna during a lightning storm. overheat. Do not dispose of batteries in a fire. Batteries should
ENGLISH

You may be electrocuted. not be exposed to excessive heat.

•• Make sure the power cord is connected securely to the TV and wall •• Moving
socket if not secured damage to the Plug and socket may occur and -- When moving, make sure the product is turned off, unplugged,
in extreme cases a fire may break out. and all cables have been removed. It may take 2 or more people
•• Do not insert metallic or inflammable objects into the product. If a to carry larger TVs. Do not press or put stress on the front panel
foreign object is dropped into the product, unplug the power cord of the TV. Otherwise, this may result in product damage, fire
and contact the customer service. hazard or injury.
•• Do not touch the end of the power cord while it is plugged in. You •• Keep the packing anti-moisture material or vinyl packing out of the
may be electrocuted. reach of children.
•• If any of the following occur, unplug the product •• Do not allow an impact shock, any objects to fall into the product,
immediately and contact your local customer service. and do not drop anything onto the screen.
-- The product has been damaged. •• Do not press strongly upon the panel with a hand or a sharp
-- If water or another substance enters the product (like an AC object such as a nail, pencil, or pen, or make a scratch on it. It may
adapter, power cord, or TV). cause damage to screen.
-- If you smell smoke or other odors coming from the TV •• Cleaning
-- When lightning storms or when unused for long periods of time. -- When cleaning, unplug the power cord and wipe gently with a
Even the TV is turned off by remote control or button, AC power soft/dry cloth. Do not spray water or other liquids directly on the
source is connected to the unit if not unplugged in. TV. Do not clean your TV with chemicals including glass cleaner,
•• Do not use high voltage electrical equipment near the TV (e.g., a any type of air freshener, insecticide, lubricants, wax (car,
bug zapper). This may result in product malfunction. industrial), abrasive, thinner, benzene, alcohol etc., which can
damage the product and/or its panel. Otherwise, this may result
•• Do not attempt to modify this product in any way without written
in electric shock or product damage.
authorization from LG Electronics. Accidental fire or electric shock
can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to
operate this product.
•• Use only an authorized attachments / accessories approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction, or product damage.
•• Never disassemble the AC adapter or power cord. This may result in
fire or electric shock.
•• Handle the adapter carefully to avoid dropping or striking it. An
impact could damage the adapter.
•• To reduce the risk of fire or electrical shock, do not touch the TV
with wet hands. If the power cord prongs are wet or covered with
dust, dry the power plug completely or wipe dust off.

4
Preparing Optional Extras
• When the TV is turned on for the first time after being shipped Optional extras can be changed or modified for quality improvement
from the factory, initialization of the TV may take approximately without any notification. Contact your dealer for buying these items.

ENGLISH
one minute. These devices work only with certain models. The model name or
• Image shown may differ from your TV. design may be changed due to the manufacturer’s circumstances or
• Your TV’s OSD (On Screen Display) may differ slightly from that policies.
shown in this manual.
• The available menus and options may differ from the input source Magic Remote Control
or product model that you are using.
• New features may be added to this TV in the future. (Depending upon model)
• The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / off button, AN-MR18BA
turning off the device and unplugging the power cord. Check whether your TV model supports Bluetooth in the Wireless
• The items supplied with your product may vary depending upon Module Specification to verify whether it can be used with the Magic
the model. Remote.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions. Wall Mounting Bracket
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 (Depending upon model)
inches) width. Make sure to use screws and wall mount bracket that meet the VESA
• Use an extension cable that supports if the USB cable or standard. Standard dimensions for the wall mount kits are described in
USB flash drive does not fit into your TV’s USB port. the following table.
• Use a certified cable with the HDMI logo attached. If you do not use
a certified HDMI cable, the screen may not display or a connection A
error may occur. B
• Recommended HDMI cable types (3 m (9.84 ft) or less)
-- High-Speed HDMI®/™ cable
-- High-Speed HDMI®/™ cable with Ethernet
OLED55/65B8*
B
B *A <
= 10 mm (0.39 inches) Model OLED55/65C8* OLED77C8*
OLED55/65E8*
A A
*B <
= 18 mm (0.7 inches) VESA (A x B) (mm) 300 x 200 400 x 200
Standard screw M6 M6
• When attaching the stand to the TV set, place the screen facing
Number of screws 4 4
down on a cushioned table or flat surface to protect the screen
from scratches. Wall mount bracket OLW480B OLW480B
• Make sure to wring any excess water or cleaner from the cloth.
• Do not spray water or cleaner directly onto the TV screen.
• Make sure to spray just enough of water or cleaner onto a dry cloth
to wipe the screen.

• Remove the bracket itself and the protective film inside it

when installing the wall mount. (Only OLED55/65E8*) 5
 Lifting and moving the TV • Avoid touching the screen at all times, as this may result
in damage to the screen.
• Do not place the product on the floor with its front facing
When moving or lifting the TV, read the following to prevent the TV down without padding. Failure to do so may result in
from being scratched or damaged and for safe transportation regardless damage to the screen.
ENGLISH

of its type and size. • Do not move the TV by holding the cable holders, as the
• It is recommended to move the TV in the box or packing material cable holders may break, and injuries and damage to the
that the TV originally came in. TV may occur, (Depending upon model).
• Before moving or lifting the TV, disconnect the power cord and • When attaching the stand to the TV set, place the screen
all cables. facing down on a cushioned table or flat surface to
• When holding the TV, the screen should face away from you to protect the screen from scratches.
avoid damage.

Mounting on the Table

1 Lift and tilt the TV into its upright position on a table. 
• Hold the side and bottom of the TV frame firmly. Make sure not • Leave a minimum of 10 cm (4 inches) space from the wall for
to hold the transparent part, speaker, or speaker grill area. (Not proper ventilation.
applicable for OLED55/65E8*)

10 cm
(4 inches)
10 cm 10 cm
10 cm

10 cm

• Use at least two people to move a large TV.

• When transporting the TV by hand, hold the TV as shown in the (Depending upon model)
following illustration.
2 Connect the power cord to a wall outlet.

(Only OLED55/65E8*)
• Hold the side of the TV with one hand, and hold the bottom of the
rear cover with the other. (Hold the rear cover when placing the TV
on the floor. Holding the bottom glass may result in injury.) (Only
OLED55/65E8*) • If you install the TV on a stand instead of mounting it on a
• When transporting the TV, do not expose the TV to jolts or wall, make sure that the removed brackets are reattached
excessive vibration. at the bottom of the TV. (Only OLED55/65E8*)
• When transporting the TV, keep the TV upright; never turn the TV
on its side or tilt towards the left or right.
• When handling the TV, be careful not to damage the protruding
buttons.

6
 • Do not apply foreign substances (oils, lubricants, etc.) to
the screw parts when assembling the product. (Doing so
Mounting to the Wall
may damage the product.)
An optional wall mount can be used with your LG Television. Consult
• If you install the TV on a stand, you need to take actions
with your local dealer for a wall mount that supports the VESA
to prevent the product from overturning. Otherwise, the

ENGLISH
standard used by your TV model. Carefully attach the wall mount
product may fall over, which may cause injury.
bracket at the rear of the TV. Install the wall mount bracket on a solid
• Do not use any unapproved items to ensure the safety
wall perpendicular to the floor. If you are attaching the TV to other
and lifespan of the product.
building materials, please contact qualified personnel to install the
• Any damages or injuries by using unapproved items are
wall mount. Detailed instructions will be included with the wall mount.
not covered by the warranty.
We recommend that you use an LG brand wall mount. The LG wall
• Make sure that the screws are fastened tightly. (If they mount is easy to adjust or to connect the cables. When you do not use
are not fastened securely enough, the TV may tilt forward LG’s wall mount bracket, use a wall mount bracket where the device is
after being installed.) adequately secured to the wall with enough space to allow connectivity
• Do not fasten the screws with excessive force otherwise to external devices. If you are using a non-adjustable mount, attach the
they may strip and become loose. mount to the wall. Attach the cables to the TV first, then attach the TV
to the mount.
Securing TV to the Wall

10 cm
(4 inches)
10 cm 10 cm
10 cm

10 cm

(Depending upon model)

(Depending upon model)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV. • Remove the stand before installing the TV on a wall
• If there are bolts inserted at the eye-bolts position, remove the mount by performing the stand attachment in reverse.
bolts first. • For more information of screws and wall mount bracket,
2 Mount the wall brackets with the bolts to the wall. Match the refer to the Separate purchase.
location of the wall bracket and the eye-bolts on the rear of the TV. • If you intend to mount the product to a wall, attach VESA
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or standard mounting interface (optional parts) to the back
cable. Make sure to keep the rope parallel to the flat surface. of the product. When you install the set to use the wall
mounting bracket (optional parts), fix it carefully so as
not to drop.
• Use a platform or cabinet that is strong and large enough to • When mounting a TV on the wall, make sure not to install
support the TV securely. the TV by hanging the power and signal cables on the
• Brackets, bolts and ropes are optional. You can obtain additional back of the TV.
accessories from your local dealer. • Do not install this product on a wall if it could be exposed
to oil or oil mist. This may damage the product and cause
it to fall.

7
 Connections External Devices
Supported external devices are: Blu-ray player, HD receivers, DVD
You can connect various external devices to the TV. For more players, VCRs, audio systems, USB storage devices, PC, gaming devices,
information on external device’s connection, refer to the manual and other external devices.
provided with each device.
ENGLISH

•• If you record a TV program on a Blu-ray/DVD recorder or VCR, make

sure to connect the TV signal input cable to the TV through a DVD
Antenna/Cable recorder or VCR. For more information about recording, refer to the
Connect an antenna, cable, or cable box to watch TV while referring to manual provided with the connected device.
the following. The illustrations may differ from the actual items and an •• The external device connections shown may differ slightly from
RF cable is optional. illustrations in a manual.
•• Connect external devices to the TV regardless about the order of
•• Make sure not to bend the copper wire of the RF cable.
the TV port.
•• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
Copper wire •• Refer to the external equipment’s manual for operating
instructions.
•• Complete all connections between devices, and then connect the •• In PC mode, there may be noise associated with the resolution,
power cord to the power outlet to prevent damage to your TV. vertical pattern, contrast or brightness. If noise is present, change
•• Use a signal splitter to use 2 TVs or more. the PC output to another resolution, change the refresh rate to
•• DTV Audio Supported Codec: MPEG, Dolby Digital another rate or adjust the brightness and contrast on the PICTURE
•• This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts menu until the picture is clear. Depending upon the graphics card,
directly because the related standards have not been confirmed, some resolution settings may not allow the image to be positioned
(Depending upon model). on the screen properly.
•• Some USB Hubs may not work. If a USB device connected through
Other connections a USB Hub is not detected, connect it directly to the USB port on
the TV.
Connect your TV to external devices. For the best picture and audio
•• The TV may be capable of operating without a set-top-box from a
quality, connect the external device and the TV with the HDMI cable.
multichannel video programming distributor (MVPD).
HDMI •• When connecting via a wired LAN, it is recommended to use a CAT
7 cable.
• Supported HDMI Audio format :
(Depending upon model)
DTS (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz),
DTS HD (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz),
Remote RS-232C setup
True HD (48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz), To obtain the RS-232C external control setup information, please
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz) visit www.lg.com. Download and read the manual, (Depending upon
model).
(Only UHD models) • Do not drop the product or let it fall over when
connecting external devices. Otherwise, this may result in
• ( ) Picture Additional Settings
injury or damage to the product.
HDMI ULTRA HD Deep Color
-- On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0) • When connecting external devices such as video game
-- Off : Support 4K @ 60 Hz 8 bit (4:2:0) consoles, make sure the connecting cables are long
If the device connected to Input Port also supports ULTRA HD Deep enough. Otherwise, the product may fall over, which may
Color, your picture may be clearer. However, if the device doesn’t cause injury or damage the product.
support it, it may not work properly. In that case, change the TV’s
HDMI ULTRA HD Deep Color setting to off.

8
Using Button
You can simply operate the TV functions, using the button.

ENGLISH
Basic functions

Power On (Press)
Power Off 1 (Press and hold)

Volume Control

Channels Control

1 All running apps will close.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust
the Menu items using the button.
Turns the power off.
Accesses the settings menu.
Clears on-screen displays and returns to TV viewing.
Changes the input source.

9
 Using Magic Remote * To use the button, press and hold for more than 3 seconds.

Control (POWER) Turns the TV on or off.

You can turn your set-top box on or off by adding the set-
top box to the universal remote control for your TV.
(Depending upon model)
ENGLISH

Number buttons Enters numbers.

The descriptions in this manual are based on the buttons on the remote (DASH) Inserts a (DASH) between numbers such as 2-1 and 2-2.
control. Please read this manual carefully and use the TV correctly. Accesses the saved channels list.
When the message “Magic Remote battery is low. Please change the (Screen Remote) Displays the Screen Remote.
battery.” is displayed, replace the batteries.
-- Accesses the Universal Control Menu in some regions.
To install batteries, open the battery cover, replace batteries (1.5 V AA)
* (Screen Remote) SAP (Secondary Audio Program) Feature can
matching the and ends to the label inside the compartment,
be enabled by pressing the key.
and close the battery cover. Be sure to point the magic remote toward
* You can access apps or Live TV using the number
the remote control sensor on the TV. To remove the batteries, perform
buttons corresponding to the features.
the installation actions in reverse. This remote uses infrared light. When
in use, it should be pointed in the direction of the TV’s remote sensor. Adjusts the volume level.
(MUTE) Mutes all sounds.
* (MUTE) Accesses the Accessibility menu.
Scrolls through the saved channels.
* (Voice recognition)
Network connection is required to use the voice recognition function.
Once the voice display bar is activated on the TV screen, press and hold
the button and speak your command out loud.
(HOME) Accesses the Home menu.
* (HOME) Shows the previous history.
(Q. Settings) Accesses the Quick Settings.
* (Q. Settings) Displays the All Settings menu.
Wheel (OK) Press the center of the Wheel button to select a
menu. You can change channels by using the wheel button.
(up/down/left/right) Press the up, down, left or right
button to scroll the menu. If you press buttons while the
pointer is in use, the pointer will disappear from the screen and Magic
Remote will operate like a general remote control. To display the
pointer on the screen again, shake Magic Remote to the left and right.
Returns to the previous level.
* Clears on-screen displays and returns to last input viewing.
Displays the program event according to time scheduler.
1 2 Streaming Service buttons Connects to the Video
Streaming Service.
1 2 (INPUT) Changes the input source.
* (INPUT) Displays a list of all the external inputs.
, , , These access special functions in some menus.
Control buttons ( , ) Controls media contents.
By zooming in on the selected area, you can view it in
full screen.
* You can zoom in on the area where the remote control is
pointed.

(Some buttons and services may not be provided depending upon

models or regions.)

10
Registering Magic Remote Control Troubleshooting
How to register the Magic Remote Control Cannot control the TV with the remote control.
To use the Magic Remote, first pair it with your TV. • Check if anything such as tape has been placed over the receiver.

ENGLISH
• Check if there is any obstacle between the product and the remote
1 Put batteries into the Magic Remote and turn the TV on.
control.
2 Point the Magic Remote at your TV and press the Wheel (OK) on • Replace the batteries with new fresh ones.
the remote control. No image display and no sound is produced.
* If the TV fails to register the Magic Remote, try again after turning • Check if the product is turned on.
the TV off and back on. • Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
How to deregister the Magic Remote
products.
Control The TV turns off suddenly.
Press the and (HOME) buttons at the same time, for five • Check the power control settings. The power supply may be
seconds, to unpair the Magic Remote with your TV. interrupted.
* P ressing and holding the button will let you cancel and re- • Check if the auto-off function is activated in the settings menu.
register Magic Remote at the same time. • If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
Abnormal Display
• It is recommended that an Access Point (AP) be located
more than 0.2 m (0.65 ft) away from the TV. If the AP is • If the TV feels cold to the touch, there may be a small flicker when
installed closer than 0.2 m (0.65 ft), the Magic remote it is turned on. This is normal; there is nothing wrong with TV.
control may not perform as expected due to frequency Some minute dot defects may be visible on the screen, appearing
interference. as tiny red, green, or blue spots. However, they have no adverse
• Do not mix new batteries with old batteries. This may effect on the TV’s performance. Avoid touching the screen or
cause the batteries to overheat and leak. holding your finger(s) against it for long periods of time. Doing so
• Failure to match the correct polarities of the battery may produce some temporary distortion effects on the screen.
may cause the battery to burst or leak, resulting in fire, • This panel is an advanced product that contains millions of pixels.
personal injury, or ambient pollution. In a very few cases, you could see fine dots on the screen while
• This apparatus uses batteries. In your community there you’re viewing the TV. Those dots are deactivated pixels and do not
might be regulations that require you to dispose of these affect the performance and reliability of the TV.
batteries properly due to environmental considerations. Generated Sound
Please contact your local authorities for disposal or • Cracking noise A cracking noise that occurs when watching or
recycling information. turning off the TV is generated by plastic thermal contraction due
• Batteries inside or inside the product shall not be to temperature and humidity. This noise is common for products
exposed to excessive heat such as sunshine, fire or the where thermal deformation is required.
like. • Electrical circuit humming/panel buzzing A low level noise
is generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending
upon the product. This generated sound does not affect the
performance and reliability of the product.

• Make sure to wring any excess water or cleaner from

the cloth.
• Do not spray water or cleaner directly onto the TV screen.
• Make sure to spray just enough of water or cleaner onto a
dry cloth to wipe the screen.

11
 Specifications
Product specifications may be changed without prior notice due to upgrade of product functions.
Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only).
ENGLISH

The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).

Broadcasting Specifications
Television system ATSC, NTSC-M, 64 & 256 QAM
Program coverage VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135
External antenna impedance 75 Ω

Wireless module (LGSBWAC72) Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range Output Power (Max.)

2400 to 2483.5 MHz 15 dBm

5150 to 5725 MHz 14.5 dBm
5725 to 5850 MHz 14.5 dBm

Bluetooth
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz 8.5 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional
frequency table.
For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device
and the body.
FCC ID: BEJLGSBWAC72 / IC: 2703H-LGSBWAC72

Environment condition
Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity Less than 80 %
Storage Temperature -20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity Less than 85 %

12
Open Source Software
Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source

ENGLISH
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
[email protected].
This offer is valid for a period of three years after our last shipment of
this product. This offer is valid to anyone in receipt of this information.

Licenses
Supported licenses may differ by model.

13
 Important Information for Information on Functions
Supporting Image Quality in
Preventing Image Retention Relation to Temporary Image
OLED is a self-emissive technology, which brings many significant Retention
ENGLISH

benefits to image quality and performance. As with any self-emitting

• OLED TV offers a function called Pixel Refresher, which helps to
display, it is possible for users of OLED TVs to experience temporary
prevent temporary image retention. This function can be operated
image retention under certain conditions, such as when displaying a
automatically or manually.
static image on the screen for a long time. Even so, this phenomenon is
• The auto feature will activate when the TV power is turned off, but
rare under ordinary viewing conditions and is not a malfunction. Below
only after the TV has been turned on for a cumulated total of four
sets forth helpful information you may refer to for using your OLED TV.
(4) hours or more, which need not be consecutive. Pixel Refresher
will automatically run for several minutes after the screen is
Examples of Images that may Cause turned off. (Please note that failure to supply the AC power or
Image Retention disconnecting the power cord from the outlet will disable the auto
feature.)
• Still images or fixed images containing certain information • To manually activate Pixel Refresher, you will have to select
that are displayed uninterrupted on the screen, such as channel Picture OLED Panel Settings Pixel Refresher in the
numbers, station logos, program titles, news or movie subtitles, settings. Once manually activated, the function will run for
and headlines. approximately one (1) hour. During this time, a horizontal line may
• Fixed menu or icons for video game consoles or broadcasting appear on the screen; however, this is not a malfunction.
set-top boxes. • If Pixel Refresher has not been manually activated for a certain
• Black bars shown on the left, right, top, or bottom of the screen, period of time, a pop-up window advising to activate this function
such as in images with a 4:3 or 21:9 ratio. will appear on the screen. Please follow the instructions set forth in
the pop-up window.
Recommended Measures for • In addition to Pixel Refresher, there are other functions available
Preventing Image Retention for protecting the screen from image retention. For example, a
function that automatically reduces the screen brightness level, in
• Avoid watching a video displaying an image as listed above for part or in whole, will be activated when a static image is displayed
extended periods of time. uninterrupted on the screen. Once the static image disappears, the
• Adjust your TV settings as below when turning on a video brightness level will automatically return to the previous level. This
exhibiting an image as listed above for extended periods of time. function is an intended function, and not a malfunction.
-- Picture Picture Mode Settings Picture Mode APS
-- Picture Picture Mode Settings OLED LIGHT Adjust
to lower value
-- Picture OLED Panel Settings Logo Luminance
Adjustment High
• Turn off the menu bar of an external device, such as a set-top
box, to prevent long-term display of the menu bar of such device.
(Please refer to the manual of the applicable external device for
instructions.)
• Adjust the settings as below when watching a video constantly
showing black bars on the left, right, top or bottom, in order to
remove the black bars.
-- Picture Aspect Ratio Settings Aspect Ratio
Vertical Zoom or All-Direction Zoom

14
Regulatory FCC Radio Frequency Interference
Requirements (for UNII devices)
High power radars are allocated as primary users of the 5.25 to 5.35 GHz
FCC NOTICE and 5.65 to 5.85 GHz bands. These radar stations can cause interference

ENGLISH
(For USA) with and/or damage this device. This device cannot be co-located with
any other transmitter.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These FCC RF Radiation Exposure Statement
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses [For having wireless function (WLAN, Bluetooth,...)]
and can radiate radio frequency energy and, if not installed and used This equipment complies with FCC radiation exposure limits set forth for
in accordance with the instructions, may cause harmful interference to an uncontrolled environment. This transmitter must not be colocated
radio communications. However, there is no guarantee that interference or operating in conjunction with any other antenna or transmitter. This
will not occur in a particular installation. If this equipment does equipment should be installed and operated with minimum distance
cause harmful interference to radio or television reception, which 20 cm (7.8 inches) between the radiator and your body. Users must
can be determined by turning the equipment off and on, the user is follow the specific operating instructions for satisfying RF exposure
encouraged to try to correct the interference by one or more of the compliance.
following measures:
-- Reorient or relocate the receiving antenna. Industry Canada Statement
-- Increase the separation between the equipment and the receiver.
(For Canada)
-- Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected. [For having wireless function (WLAN, Bluetooth,...)]
-- Consult the dealer or an experienced radio/TV technician for This device contains licence-exempt transmitter(s)/receiver(s) that
help. comply with Innovation, Science and Economic Development Canada’s
This device complies with part 15 of the FCC Rules. Operation is subject licence-exempt RSS(s). Operation is subject to the following two
to the following two conditions: (1) this device may not cause harmful conditions:
interference and (2) this device must accept any interference received,
(1) This device may not cause interference.
including interference that may cause undesired operation. Any
changes or modifications in construction of this device which are not (2) This device must accept any interference, including interference
expressly approved by the party responsible for compliance could void that may cause undesired operation of the device.
the user’s authority to operate the equipment. IC Radiation Exposure Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm (7.8 inches) between the
antenna & your body.
NOTE : THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.

15
 RSS-247 Requirement WARNING!
(For Canada) Never place a television set in an unstable location. A television set may
[For product having the wireless function using 5 GHz frequency bands] fall, causing serious personal injury or death. Many injuries, particularly
to children, can be avoided by taking simple precautions such as:
(1) the device for operation in the band 5150–5250 MHz is only for
ENGLISH

indoor use to reduce the potential for harmful interference to •• Using cabinets or stands recommended by the manufacturer of the
co-channel mobile satellite systems; television set.
(2) for devices with detachable antenna(s), the maximum antenna •• Only using furniture that can safely support the television set.
gain permitted for devices in the bands 5250-5350 MHz and •• Ensuring the television set is not overhanging the edge of the
5470-5725 MHz shall be such that the equipment still complies supporting furniture.
with the e.i.r.p. limit; •• Not placing the television set on tall furniture (for example,
(3) for devices with detachable antenna(s), the maximum antenna cupboards or bookcases) without anchoring both the furniture and
gain permitted for devices in the band 5725-5850 MHz shall be the television set to a suitable support.
such that the equipment still complies with the e.i.r.p. limits as •• Not placing the television set on cloth or other materials that may
appropriate; and be located between the television set and supporting furniture.
(4) [for devices operating in the band 5250-5350 MHz having an e.i.r.p. •• Educating children about the dangers of climbing on furniture to
greater than 200 mW] Antenna type(s), antenna models(s), and reach the television set or its controls.
worst-case tilt angle(s) necessary to remain compliant with the If your existing television set is being retained and relocated, the same
e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 of considerations as above should be applied.
RSS-247 shall be clearly indicated.
Symbols
Users should also be advised that high-power radars are allocated as
primary users (i.e. priority users) of the bands 5250-5350 MHz and Refers to alternating current (AC).
5650-5850 MHz and that these radars could cause interference and/or Refers to direct current (DC).
damage to LE-LAN devices.
Refers to class II equipment.
NOTE TO CABLE/TV INSTALLER Refers to stand-by.
(For USA and Canada) Refers to “ON” (power).
This reminder is provided to call the CATV system installer’s attention to Refers to dangerous voltage.
Article 820-40 of the National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.

16
ENGLISH

17
 18
ENGLISH
CHILD SAFETY:

ENGLISH
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY CARES
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to
making home entertainment safe and enjoyable.
• As you enjoy your television, please note that all televisions – new and old- must be supported on
proper stands or installed according to the manufacturer’s recommendations. Televisions that
are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,
may fall over, resulting in injury.

TUNE IN TO SAFETY
• ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.
• ALWAYS read and follow all instructions for proper use of your television.
• NEVER allow children to climb on or play on the television or the furniture on which the television
is placed.
• NEVER place the television on furniture that can easily be used as steps, such as a chest of
drawers.
• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
• ALWAYS route cords and cables connected to the television so that they cannot be tripped
over, pulled or grabbed.

WALL OR CEILING MOUNT YOUR TELEVISION

• ALWAYS contact your retailer about professional installation if you have any doubts about your
ability to safely mount your television.
• ALWAYS use a mount that has been recommended by the television manufacturer and has a
safety certification by an independent laboratory (such as UL, CSA, ETL).
• ALWAYS follow all instructions supplied by the television and mount manufacturers.
• ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.
Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder
block construction. If you are unsure, contact a professional installer.
• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount
installation.

MOVING AN OLDER TELEVISION TO A NEW PLACE IN

YOUR HOME
• Many new television buyers move their older CRT televisions into a secondary room after the
purchase of a flat-panel television. Special care should be made in the placement of older CRT
televisions.
• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size
and weight.
• NEVER place your older CRT television on a dresser where children may be tempted to use the
drawers to climb.
• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.

CE.org/safety

19
Declaration of Conformity LG Customer Information Center
Trade Name LG For inquires or comments, visit www.lg.com or call;
Responsible Party LG Electronics Inc. 1-800-243-0000 USA, Consumer User
Address 1000 Sylvan Ave. Englewood 1-888-865-3026 USA, Commercial User
Cliffs NJ 07632 U.S.A 1-888-542-2623 CANADA
TEL 201-266-2534
Register your product Online!
www.lg.com

The model and serial numbers of the TV are located

on the back and on one side of the TV. Record them
below should you ever need service.

MODEL

SERIAL NO.
SMART TV Quick Setup Guide

* Image shown may differ from your TV.

* Image shown on a PC or mobile phone may vary depending on the OS(Operating System).
* App icon positions may vary on the platform, depending upon the software version.

Network Settings
1 Press the (Home) button on the remote to
access the Home menu. Point the (Settings) Picture
WI-FI CONNECTION
Network /

icon and select by pressing the Wheel (OK) Sound ꔐ

button on the remote.
Channels

Network

General Add a Hidden Wireless Network

Connect via WPS PBC
Safety Connect via WPS PIN
Advanced Wi-Fi Settings
Accessibility

For wireless AP (Router) that have the

symbol, you need to enter the security key.
5 If the connection is successful, the "Connected
2 Point the ( ) (All Settings) icon and select
to Internet" is displayed.
by pressing the Wheel (OK) button on the
remote.
Picture
NETWORK
Sound TV Name

Wired Connection (Ethernet)

Channels Not Connected
Wi-Fi Connection
Connected to Internet
Network
Wi-Fi Direct

General

( )
Safety

All Settings
Accessibility

3 Select the Network → Wired Connection You can check the status of connection in
(Ethernet) or Wi-Fi Connection. Advanced Wi-Fi settings.

Picture
NETWORK WI-FI CONNECTION
Picture Network /
Sound TV Name
Sound ꔐ
Wired Connection (Ethernet)
Channels Not Connected
Channels
Wi-Fi Connection
Not Connected
Network
Wi-Fi Direct Network

General
General Add a Hidden Wireless Network
Safety Connect via WPS PBC
Safety Connect via WPS PIN
Accessibility Advanced Wi-Fi Settings
Accessibility

4 The device automatically tries to connect to the

network available (wired network first).
When you select the Wi-Fi Connection, the
network list available is displayed. Choose the
network you wish to use. www.lg.com
 Troubleshooting Network Problems
1 Press the (Home) button on the remote to Follow the instructions below that match to your
access the Home menu. Point the (Settings) network status.
icon and select by pressing the Wheel (OK)
Check the TV or the AP (Router).
button on the remote.

When X appears next to TV:

1 Check the connection status of the TV, AP
(Router) and cable modem.
2 Power off and power on in the following order;
(1st) the cable modem, wait for the cable
modem to reset, (2nd) the AP (Router), wait for
2 Point the ( ) (All Settings) icon and select the AP (Router) to reset and (3rd) the TV.
by pressing the Wheel (OK) button on the 3 If you are using a static IP, enter the IP directly.
remote.
4 Contact internet service provider or AP (Router)
manufacturer.

Check the AP (Router) or consult your Internet

service provider.

All Settings
( )
3 Select the Network → Wired Connection When X appears next to Gateway:
(Ethernet) or Wi-Fi Connection → Advanced 1 Unplug the power cord of the AP (Router) or
Wi-Fi Settings. cable modem, wait 5 seconds. Reapply power.
2 Initialize (Reset) the AP (Router) or cable
Picture
NETWORK Picture
WI-FI CONNECTION
Network /
modem.
Sound TV Name Sound ꔐ
3 Contact Internet service provider or AP (Router)
Wired Connection (Ethernet)
manufacturer.
Channels Not Connected Channels

Network
Wi-Fi Connection
Not Connected
Wi-Fi Direct
 Network

General General Add a Hidden Wireless Network

Connect via WPS PBC
Safety Safety Connect via WPS PIN

Accessibility Accessibility
Advanced Wi-Fi Settings When X appears next to DNS:
1 Unplug the power cord of the AP (Router) or
cable modem, wait 5 seconds. Reapply power.
2 After the cable modem or AP (Router) has
initialized (Reset), try to reconnect.
3 Check that the MAC address of the TV/AP
(Router) is registered with your Internet service
provider. (The MAC address displayed on the
right pane of the network status window
should be registered with your Internet service
provider.)
4 Check the AP (Router) manufacturer’s website
to make sure your router has the latest firmware
version installed.
 SmartShare PC SW Installing & Setting
1 Install the SmartShare PC SW programme on your PC.
2 Go to . Then, select your region.
3 Select Support.
4 Select Software & Drivers. Then, select SmartShare.
5 Download the SmartShare PC SW and install it on your PC. You can run the program when installation is
complete.

NOTE
yy Smartshare service is only available if TV and other devices are connected via a single AP (Router).

SmartShare Connection to Smartphone

1 Check that Wi-Fi is enabled on your smartphone. To use SmartShare, both devices must
on the same local network.
2 Install/run the app for sharing content on your smartphone (It's called LG TV Plus on LG
phones).
3 Enable your smartphone to share content files with other devices.
4 Open Device Connector application.
(Home) → Device Connector → Smartphone → CONTENT SHARE.
5 Select the file type you want to play (movie, audio or photo).
6 Select a movie, music or photo file to play on the TV.
7 Play the media file to view and enjoy it on your TV.

Updating the TV Firmware

* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may
take a few minutes.
1 (Home) → (Settings) → ( ) (All Settings) → General → About This TV → CHECK FOR
UPDATES
2 After checking the version of the software, update it.
If you check the "Allow Automatic Updates", you can update the software automatically.

Picture
GENERAL Picture
ABOUT THIS TV
General /

Sound Eco Mode Sound

Software Version xx.xx.xx


Mobile TV On
Channels Channels ꔐ Allow Automatic Updates

CHECK FOR UPDATES

Network LG Wireless Keyboard Network

Settings Help TV Information

General General
No Signal Image User Guide
Safety Reset to Initial Settings Safety Open Source Software Notice

About This TV Set ID : 1

Accessibility Accessibility
User Agreements
 Wi-Fi Direct Setting
WI-FI Direct (Home) → (Settings) → ( ) (All Settings) → Network → Wi-Fi Direct
Picture Network / REFRESH LIST
If a local network is not available, you can connect a portable device directly to the TV
Sound ꔐ
using Wi-Fi Direct.
Channels
With , you can share files or screens of devices connected to Wi-Fi Direct.
Network

General
1 When you open Wi-Fi Direct menu, a list of available devices appears.
Safety 2 When you are prompted to request connection, select Yes. Wi-Fi Direct is now
Accessibility connected to your TV.
* You can only use devices that support Wi-Fi Direct.

Miracast Setting
Miracast allows a portable device to send video and sound securely to the TV wirelessly.
1 Miracast should be set to "ON" on your portable device.
2 When your TV is detected, select the device on your portable device.
When connection is completed, the device screen appears on the TV screen.

Please call LG Customer Service if you experience any problems.

Guide d’installation rapide du téléviseur SMART

* Les images présentées pourraient ne pas correspondre à votre téléviseur.

* Les images affichées sur un ordinateur ou un téléphone mobile peuvent varier en fonction du SE (système
d’exploitation).
* L’emplacement de l’icône de l’application peut varier sur la plateforme, en fonction de la version du logi-
ciel.

Paramètres réseau
1 Appuyez sur le bouton (Accueil) de la
télécommande pour accéder au menu d’accueil. Image
CONNEXION WI-FI
Réseau /
Visez l’icône (Paramètres) et sélectionnez-la
en appuyant sur le bouton Molette (OK) de la Son ꔐ

télécommande. Chaînes

Réseau

Général Ajoutez un réseau sans fil caché

Se connecter via WPS-PBC
Sécurité Se connecter via PIN WPS
Paramètres Wi-Fi avancés
Accessibilité

Pour les points d’accès sans fil (routeur) affichant

le symbole , vous devez saisir le code de
sécurité.
2 Visez l’icône ( ) (Tous les paramètres) et 5 Lorsque la connexion est établie, la mention
sélectionnez-la en appuyant sur le bouton « Connecté à Internet » est affichée.
Molette (OK) de la télécommande.

Image
RÉSEAU
Son NOM DE LA TV

Connexion filaire (Ethernet)

Chaînes Non connecté
Connexion Wi-Fi
Connecté à Internet
Réseau
Wi-Fi Direct

( )
Général

Tous les paramètres

Sécurité

Accessibilité
3 Sélectionnez le Réseau → Connexion filaire
(Ethernet) ou Connexion Wi-Fi.
Vous pouvez vérifier l’état de la connexion dans
Paramètres Wi-Fi avancés.
Image
RÉSEAU
Son NOM DE LA TV

Chaînes
Connexion filaire (Ethernet)
Non connecté
Image
CONNEXION WI-FI
Réseau /
Connexion Wi-Fi
Non connecté
Réseau
Wi-Fi Direct Son ꔐ

Général Chaînes

Sécurité Réseau

Accessibilité Général Ajoutez un réseau sans fil caché

Se connecter via WPS-PBC
4 L’appareil tente automatiquement de se Sécurité Se connecter via PIN WPS
Paramètres Wi-Fi avancés
connecter au réseau disponible (réseau filaire en Accessibilité

premier).
Lorsque vous sélectionnez la Connexion Wi-Fi, la
liste des réseaux disponibles s’affiche. Choisissez
le réseau que vous voulez utiliser.

www.lg.com
 Dépannage des problèmes réseau
1 Appuyez sur le bouton (Accueil) de la Suivez les instructions ci-dessous qui correspondent
télécommande pour accéder au menu d’accueil. à l’état de votre réseau.
Visez l’icône (Paramètres) et sélectionnez-la
en appuyant sur le bouton Molette (OK) de Vérifiez le téléviseur ou le point d’accès (routeur).
la télécommande.

Lorsqu’une croix (X) apparaît à côté du téléviseur :

1 Vérifiez l’état de la connexion du téléviseur, du point
d’accès (routeur) et du modem câble.
2 Mettez les appareils hors tension et sous tension
dans l’ordre suivant : (1) le modem câble, attendez
que le modem câble se réinitialise; (2) le point
2 Visez l’icône ( ) (Tous les paramètres) et d’accès (routeur), attendez que le routeur se
sélectionnez-la en appuyant sur le bouton réinitialise et (3) le téléviseur.
Molette (OK) de la télécommande.
3 Si vous utilisez une adresse IP fixe, saisissez-la
directement.
4 Communiquez avec le fournisseur d’accès à Internet
ou avec le fabricant du point d’accès (routeur).

Vérifiez le point d’accès (routeur) ou consultez

votre fournisseur d’accès à Internet.
Tous les paramètres
( )
3 Sélectionnez le Réseau → Connexion filaire
(Ethernet) ou Connexion Wi-Fi → Paramètres Lorsqu’une croix (X) apparaît à côté de la
Wi-Fi avancés. passerelle :
Image
RÉSEAU Image
CONNEXION WI-FI
Réseau /
1 Débranchez le cordon d’alimentation du point d’accès
(routeur) ou du modem câble, attendez 5 secondes,
Son NOM DE LA TV Son ꔐ puis rebranchez-le.
Connexion filaire (Ethernet)
Chaînes Non connecté Chaînes
2 Réinitialisez le point d’accès (routeur) ou le modem
Réseau
Connexion Wi-Fi
Non connecté
Wi-Fi Direct
 Réseau câble.
Général Général Ajoutez un réseau sans fil caché 3 Communiquez avec le fournisseur d’accès Internet
Se connecter via WPS-PBC ou le fabricant du point d’accès (routeur).
Sécurité Sécurité Se connecter via PIN WPS
Paramètres Wi-Fi avancés
Accessibilité Accessibilité

Lorsqu’une croix (X) apparaît à côté du DNS :

1 Débranchez le cordon d’alimentation du point d’accès
(routeur) ou du modem câble, attendez 5 secondes,
puis rebranchez-le.
2 Une fois que le modem câble ou le point
d’accès (routeur) est réinitialisé, essayez de vous
reconnecter.
3 Vérifiez que l’adresse MAC du téléviseur ou du
point d’accès (routeur) est enregistrée auprès de
votre fournisseur d’accès à Internet. (L’adresse
MAC affichée dans le volet droit de la fenêtre d’état
du réseau doit être enregistrée auprès de votre
fournisseur d’accès Internet.)
4 Consultez le site Web du fabricant de votre point
d’accès (routeur) afin de vérifier que celui-ci exécute
la dernière version du microprogramme.
 Installation et configuration du logiciel PC SmartShare
1 Installez le logiciel PC SmartShare sur votre ordinateur.
2 Rendez-vous sur , puis sélectionnez votre région.
3 Sélectionnez Soutien.
4 Sélectionnez Logiciels et micrologiciels. Sélectionnez Partage "SmartShare".
5 Téléchargez le logiciel PC SmartShare et installez-le sur votre ordinateur. Vous pouvez exécuter le
programme lorsque l’installation est terminée.

REMARQUE
yy Le service Smartshare est offert uniquement si le téléviseur et les autres appareils sont connectés au
même point d’accès (routeur).

Connexion SmartShare à un téléphone intelligent

1 Vérifiez que l’option Wi-Fi est activée sur votre téléphone intelligent. Pour utiliser
SmartShare, les deux appareils doivent être sur le même réseau local.
2 Installez/exécutez l’application de partage de contenu sur votre téléphone intelligent (sur
les téléphones LG, il s’agit de LG TV Plus).
3 Activez l’option sur votre téléphone intelligent afin de partager des fichiers avec d’autres
appareils.
4 Ouvrez l’application Connecteur de périphérique.
(Accueil) → Connecteur de périphérique → Téléphone intelligent → PARTAGE
DE CONTENU.
5 Sélectionnez le type de fichier que vous voulez lire (film, musique ou photo).
6 Sélectionnez un fichier de film, de musique ou de photo à lire.
7 Lisez le fichier multimédia sur votre téléviseur.

Mise à jour du micrologiciel du téléviseur

* S’il s’agit de la première fois que le téléviseur est allumé depuis sa sortie d’usine, l’initialisation peut
prendre quelques minutes.

1 (Accueil) → (Paramètres) → ( ) (Tous les paramètres) → Général → À propos de ce

téléviseur → Rechercher des mises à jour
2 Vérifiez d’abord la version du logiciel, puis mettez-le à jour.
Si vous cochez la case « Autoriser les mises à jour automatiques », vous pouvez mettre à jour le logiciel
automatiquement.

Image
GÉNÉRAL Image
À PROPOS DE CE TÉLÉVISEUR
Général /

Son Mode éco. Son

Version du logiciel xx.xx.xx


Télé mobile active
Chaînes Chaînes ꔐ Autoriser les mises à jour automatiques

Rechercher des mises à jour

Réseau Clavier sans fil LG Réseau

Aide relative aux Paramètres Renseignements sur le téléviseur

Général Général
Image Aucun signal Guide de l’utilisateur
Sécurité Réinitialiser les paramètres initiaux Sécurité Notice de logiciel ouvert

À propos de ce téléviseur ID du groupe : 1

Accessibilité Accessibilité
Accords utilisateur
 Configuration de Wi-Fi Direct
WI-FI Direct (Accueil) → (Paramètres) → ( ) (Tous les paramètres) → Réseau →
Image Réseau / ACTUALISER LA LISTE Wi-Fi Direct
Son ꔐ S’il n’y a pas de réseau local disponible, vous pouvez connecter un appareil mobile
Chaînes directement au téléviseur à l’aide de Wi-Fi Direct.
Réseau
Grâce à , vous pouvez partager des fichiers ou les écrans d’appareils
connectés à Wi-Fi Direct.
Général

Sécurité 1 Lorsque vous ouvrez le menu Wi-Fi Direct, une liste d’appareils disponibles
Accessibilité
apparaît.
2 Lorsque vous êtes invité(e) à demander une connexion, sélectionnez OK. Wi-
Fi Direct est à présent connecté à votre téléviseur.
* Vous ne pouvez utiliser que les périphériques qui prennent en charge Wi-Fi
Direct.

Configuration de Miracast
Miracast permet à un appareil mobile d’envoyer sans fil et de manière sécuritaire des vidéos et
du contenu audio au téléviseur.
1 L’option Miracast doit être sur « ON » (activée) sur votre appareil mobile.
2 Lorsque votre téléviseur est détecté, sélectionnez-le sur vot re appareil mobile.
Une fois la connexion établie, l’écran de l’appareil apparaît sur le téléviseur.

Appelez le service à la clientèle de LG si vous constatez le moindre problème.

Guía de configuración rápida del SMART TV

* La imagen que se muestra puede ser diferente a su televisor.

* La imagen que se muestra en una PC o un teléfono móvil puede variar según el sistema operativo
(sistema operativo).
* Las posiciones de los íconos de la aplicación pueden variar en la plataforma según la versión del software.

Configuración de la red
1 Presione el botón (Inicio) del control remoto
para acceder al menú Inicio. Vaya al ícono Imagen Red /
CONEXIÓN WI-FI
(Configuración) y selecciónelo con el botón Audio ꔐ
Rueda (Aceptar) del control remoto.
Canales

Red

General Agregar una red inalámbrica oculta

Conectarse a través de WPS PBC
Seguridad Conectar mediante WPS PIN
Configuración avanzada de Wi-Fi
Accesibilidad

Para el AP inalámbrico (enrutador) que tiene el

símbolo , debe ingresar la clave de seguridad.
2 Vaya al ícono ( ) (Todos los ajustes) y 5 Si la conexión es exitosa, se muestra "Conectado
selecciónelo con el botón Rueda (Aceptar) a Internet".
del control remoto.
Imagen
RED
Audio Nombre de la TV

Conexión cableada (Ethernet)

Canales No conectado
Conexión Wi-Fi
Conectado a Internet
Red
Wi-Fi Direct

General

Todos los ajustes

( ) Seguridad

Accesibilidad

3 Seleccione Red → Conexión cableada

(Ethernet) o Conexión Wi-Fi. Puede verificar el estado de conexión en
Configuración avanzada de Wi-Fi.

Imagen
RED
Audio Nombre de la TV
Imagen
CONEXIÓN WI-FI
Red /
Conexión cableada (Ethernet)
Canales No conectado
Conexión Wi-Fi
Audio ꔐ
No conectado
Red
Wi-Fi Direct Canales

General
Red

Seguridad
General Agregar una red inalámbrica oculta
Accesibilidad Conectarse a través de WPS PBC
Seguridad Conectar mediante WPS PIN
Configuración avanzada de Wi-Fi
4 El dispositivo intenta conectarse Accesibilidad

automáticamente a la red disponible (primero,

la red cableada).
Cuando selecciona Conexión Wi-Fi, se muestra
la lista de redes disponibles. Seleccione la red
que desea usar.
www.lg.com
 Resolución de problemas de red
1 Presione el botón (Inicio) del control remoto Siga las instrucciones que están a continuación y
para acceder al menú Inicio. Vaya al ícono que se relacionan con el estado de red.
(Configuración) y selecciónelo con el botón
Revise el televisor o el AP (enrutador).
Rueda (Aceptar) del control remoto.

Cuando aparece X al lado del televisor:

1 Revise el estado de la conexión del TV, el Punto
de Acceso (Router), y módem de cable.
2 Apague y encienda en el siguiente orden:
(Primero) el módem de cable, espere que el
2 Vaya al ícono ( ) (Todos los ajustes) y módem de cable se restablezca, (Segundo) el
selecciónelo con el botón Rueda (Aceptar) Punto de Acceso (Router), espere a que el Punto
del control remoto. de Acceso (Router) se restablezca, (Tercero) la
TV.
3 Si usa una dirección IP estática, ingrésela
directamente.
4 Comuníquese con el proveedor de servicios de
Internet o la empresa de AP (enrutador).

Revise el AP (enrutador) o consulte a su

Todos los ajustes
( ) proveedor de servicios de Internet.

3 Seleccione Red → Conexión cableada

(Ethernet) o Conexión Wi-Fi → Configuración
avanzada de Wi-Fi.
Cuando aparece X junto a la puerta de enlace:
Imagen
RED Imagen
CONEXIÓN WI-FI 1 Desenchufe el cable de alimentación del AP
Red /
(enrutador) e intente conectarlo después de 5
Audio Nombre de la TV Audio ꔐ segundos.
Canales
Conexión cableada (Ethernet)
No conectado Canales 2 Inicialice (restablezca) el AP (enrutador).
Red
Conexión Wi-Fi
No conectado
 Red
3 Comuníquese con el proveedor de servicios de
Wi-Fi Direct
Internet o la empresa de AP (enrutador).
General General Agregar una red inalámbrica oculta
Conectarse a través de WPS PBC
Seguridad Seguridad Conectar mediante WPS PIN
Configuración avanzada de Wi-Fi
Accesibilidad Accesibilidad

Cuando aparece X junto a DNS:

1 Desconecte el cable de alimentación del Punto
de Acceso (Router), y del módem de cable ,
espere 5 segundos. Vuelva a conectar los cables
de alimentación, y vuelva a intentar la conexión.
2 Inicialice (Reset) el Punto de Acceso (Router), o
el módem de cable.
3 Verifique que la dirección MAC del TV/AP
(enrutador) esté registrada con su proveedor
de servicios de Internet. (La dirección MAC que
se muestra en el panel derecho de la ventana
de estado de red debe registrarse con su
proveedor de servicios de Internet.)
4 Consulte el sitio web del fabricante del
AP (enrutador) para asegurarse de que su
enrutador tenga instalada la última versión de
firmware.
 Instalación y configuración de SmartShare PC SW
1 Instale el programa SmartShare PC SW en su PC.
2 Vaya a . Luego, seleccione su región.
3 Seleccione Soporte.
4 Select Software y actualizaciones. Then, select SmartShare.
5 Descargue el Software SmartShare PC e instálelo en su PC. Puede ejecutar el programa al finalizar la
instalación.

NOTA
yy El servicio Smartshare solo está disponible si el televisor y otros dispositivos están conectados a
través de un solo AP (enrutador).

Conexión de SmartShare a un teléfono inteligente

1 Verifique que la conexión Wi-Fi esté activada en su teléfono inteligente. Para utilizar
SmartShare, ambos dispositivos deben estar en la misma red local.
2 Instale y ejecute la aplicación para compartir contenido en su teléfono inteligente (se
llama LG TV Plus en teléfonos LG).
3 Permita que su teléfono inteligente comparta archivos de contenido con otros
dispositivos.
4 Abra la aplicación Conector de Dispositivo.
(Inicio) → Conector de Dispositivo → Teléfono Inteligente → COMPARTIR
CONTENIDO.
5 Seleccione el tipo de archivo que desea reproducir (película, audio o foto).
6 Seleccione una película, música o archivo de fotografía para reproducir en el televisor.
7 Reproduzca el archivo multimedia para verlo y disfrutarlo en su televisor.

Actualización del firmware del televisor

* Cuando el televisor se enciende por primera vez después de que se envía de fábrica, la inicialización del
televisor puede tardar unos minutos.
1 (Inicio) → (Configuración) → ( ) (Todos los ajustes) → General → Acerca de este TV →
BUSCAR ACTUALIZACIONES
2 Después de verificar la versión del software, actualícela.
Si marca la opción "Permitir Actualizaciones Automáticas", puede actualizar el software
automáticamente.

Imagen
GENERAL Imagen
ACERCA DE ESTE TV
General /

Audio Modo Eco Audio

Versión de software xx.xx.xx


TV móvil activo
Canales Canales ꔐ Permitir Actualizaciones Automáticas

BUSCAR ACTUALIZACIONES
Red Teclado inalámbrico LG Red

Ayuda para la configuración Información del TV

General General
Imagen sin señal Guía del usuario
Seguridad Restablecer la configuración inicial. Seguridad Aviso de software de código abierto

Acerca de este TV ID de configuración: 1

Accesibilidad Accesibilidad
Acuerdos del usuario
 Configuración de Wi-Fi Direct
WI-FI Direct (Inicio) → (Configuración) → ( ) (Todos los ajustes) → Red → Wi-Fi
Imagen Red / ACTUALIZAR LISTA Direct
Audio ꔐ Si no hay una red local disponible, puede conectar un dispositivo portátil
Canales directamente al televisor con Wi-Fi Direct.
Red
Con , puede compartir archivos o pantallas de dispositivos conectados
a Wi-Fi Direct.
General

Seguridad 1 Cuando abre el menú Wi-Fi Direct, aparece una lista de los dispositivos
Accesibilidad disponibles.
2 Cuando se le indica que solicite conexión, seleccione OK. Wi-Fi Direct ahora
está conectado a su televisor.
* Solo puede utilizar dispositivos compatibles con Wi-Fi Direct.

Configuraciones Miracast
Miracast permite que el dispositivo portátil envíe vídeos y sonidos al TV sin cables deform
1 Miracast debe configurarse en "ENCENDIDO" en su dispositivo móvil.
2 Cuando se detecta el televisor, seleccione el dispositivo en su dispositivo portátil.
Cuando se completa la conexión, aparece la pantalla del dispositivo en la pantalla del
televisor.

Comuníquese con el Servicio de atención al cliente de LG si tiene algún problema.

Guia Rápido de Configuração SMART TV

* As imagens neste guia podem ser diferentes da TV.

* As imagens do PC ou Telefone podem ser diferentes dependendo do sistema operacional.
* A posição dos ícones de Aplicativos podem variar na plataforma, dependendo da versão de software.

Ajustes de Rede
1 No controle remoto, pressione o botão
(Home) para acessar o menu principal. No Imagem Rede /
CONEXÃO DA REDE WI-FI
menu, selecione (CONFIGURAÇÕES) e Som ꔐ
pressione o botão Scroll (OK). Canais

Rede

Geral Adicionar uma rede sem fio oculta

Conectar através de WPS PBC
Segurança Conectar através de WPS PIN
Configurações avançadas de Wi-Fi
Acessibilidade

Para roteadores protegidos, o símbolo é

exibido indicando a necessidade de senha para
acessar a rede.
2 Selecione ( ) (Todas as Configurações) e
5 Caso a conexão esteja correta, a mensagem
pressione o botão Scroll (OK). "Conectado à Internet" será exibida.

Imagem
REDE
Som Nome da TV

Conexão com fio (Ethernet)

Canais Não conectado
Wi-Fi Connection
Conectado à Internet
Rede
Wi-Fi Direct

Todas as Configurações
( ) Geral

Segurança

3 No menu selecione Rede → Conexão com fio Acessibilidade

(Ethernet) ou Conexão da rede Wi-Fi.

Caso deseje, verifique o status da conexão
acessando a opção Configurações avançadas
Imagem
REDE de Wi-Fi.
Som Nome da TV

Canais
Conexão com fio (Ethernet)
Não conectado Imagem
CONEXÃO DA REDE WI-FI
Rede /
Conexão da rede Wi-Fi
Não conectado
Rede Som ꔐ
Wi-Fi Direct

Geral Canais

Segurança Rede

Acessibilidade Geral Adicionar uma rede sem fio oculta

Conectar através de WPS PBC
Segurança Conectar através de WPS PIN
4 O dispositivo será conectado automaticamente Configurações avançadas de Wi-Fi
Acessibilidade
em uma rede disponível (rede com fio em
primeiro lugar).
Ao selecionar Conexão da rede Wi-Fi, uma lista
de redes será disponibilizada. Selecione a rede
desejada.
www.lg.com
 Problemas de Rede - Soluções
1 No controle remoto, pressione o botão As instruções abaixo servem para verificar o status
(Home) para acessar o menu principal. No menu, da conexão de rede.
selecione (CONFIGURAÇÕES) e pressione o
Verifique a TV ou o Roteador.
botão Scroll (OK).

Quando o X estiver próximo do ícone TV:

1 Verifique o status da conexão na TV, Roteador e
Modem.
2 Desligue os equipamentos na ordem: (1º) o
modem, aguarde o modem reiniciar, (2º) o ro-
teador, aguarde o roteador reiniciar e (3º) a TV.
3 Selecione ( ) (Todas as Configurações) e 3 Nos casos de endereço IP estático será necessá-
rio inseri-lo manualmente.
pressione o botão Scroll (OK).
4 Se o problema persistir, contate o provedor de
internet ou o fabricante do roteador.

Verifique o roteador ou contate o provedor de

internet.

Todas as Configurações
( )
4 Selecione Rede → Conexão com fio (Ethernet) Quando o X estiver próximo do ícone Gateway:
ou Conexão da rede Wi-Fi → Configurações 1 Desconecte o cabo de força da tomada do ro-
avançadas de Wi-Fi. teador ou modem, aguarde 5 segundos e torne
a conectar.
Imagem
REDE Imagem
CONEXÃO DA REDE WI-FI
Rede / 2 Reinicie o roteador e o modem.
Som Nome da TV Som ꔐ 3 Contate seu provedor de internet e o fabricante
Canais
Conexão com fio (Ethernet)
Canais
do roteador.
Não conectado

Rede
Conexão da rede Wi-Fi
Não conectado
Wi-Fi Direct
 Rede

Geral Geral Adicionar uma rede sem fio oculta

Conectar através de WPS PBC
Segurança Segurança Conectar através de WPS PIN
Configurações avançadas de Wi-Fi
Acessibilidade Acessibilidade Quando o X estiver próximo do ícone DNS:
1 Desconecte o cabo de força da tomada do ro-
teador ou modem, aguarde 5 segundos e torne
a conectar.
2 Reinicie o roteador e o modem e tente reconec-
tar
3 Verifique se o endereço MAC da TV/Roteador
está registrado no seu provedor de internet (o
endereço MAC é exibido na janela de status de
rede. Envie este número ao seu provedor para
registrá-lo).
4 Verifique no site do fabricante do seu roteador
se a última versão do firmware está instalada.
 Instalar & Configurar o SmartShare PC Software
1 Instale o SmartShare PC em seu computador.
2 Acesse . Se necessário, selecione seu país ou região.
3 Selecione Suporte.
4 Selecione Software & Drivers. Então, selecione SmartShare.
5 Faça o download e instale o software. Após a finalização da instalação será possível executar e configurar
o programa.

NOTE
yy A função Smartshare está disponível na TV e em dispositivos conectados ao mesmo roteador.

SmartShare - Conectando um Smartphone

1 Ative a conexão Wi-Fi no Smartphone. Para conectar usando o SmartShare, os dispositi-
vos (TV e Smartphone) devem estar conectados na mesma rede.
2 No Smartphone, instale ou execute o aplicativo de compartilhamento (se desejar instale
o aplicativo LG TV Plus).
3 Ative o compartilhamento para compartilhar conteúdo com outros dispositivos.
4 Acesse (Home) e execute o aplicativo Conector de Dispositivos. No menu acesse a
opção Smartphone → COMPARTILHAMENTO DE CONTEÚDO.
5 Selecione o tipo de arquivo desejado (filme, música ou foto).
6 Selecione o conteúdo desejado para reproduzi-lo na TV.
7 Inicie a reprodução do conteúdo selecionado na TV.

Atualizando o Software da TV
* Ao ligar a TV pela primeira vez, a inicialização do aparelho pode levar alguns minutos.
1 (Home) → (CONFIGURAÇÕES) → ( ) (Todas as Configurações) → Geral → Sobre esta
TV → VERIFICAR POR ATUALIZAÇÕES
2 Após verificar, execute o processo de atualização.
Se desejar, selecione a opção "Permitir Atualizações Automáticas", para atualizar o software da TV
automaticamente.

Imagem
GERAL Imagem
SOBRE ESTA TV
Geral /

Som Modo Eco Som

Versão do software xx.xx.xx


TV Mobile ativada
Canais Canais ꔐ Permitir Atualizações Automáticas

Verificar por atualizações

Rede Teclado LG Sem Fio Rede

Ajuda com as configurações Informações da TV

Geral Geral
Proteção de Tela Guia do Usuário
Segurança Redefinir para Configurações Iniciais Segurança Aviso sobre Software de Código...

Sobre esta TV Definir ID : 1

Acessibilidade Acessibilidade
Acordos de Usuário
 Ajustar Wi-Fi Direct
WI-FI DIRECT (Home) → (CONFIGURAÇÕES) → ( ) (Todas as Configurações) →
Imagem REDE / ATUALIZAR ... Rede → Wi-Fi Direct
Som ꔐ
Caso uma rede local não esteja disponível, conecte-se diretamente a TV usando a
Canais
função Wi-Fi Direct.
Rede Usando , será possível compartilhar telas ou arquivos usando Wi-Fi
Geral
Direct.
Segurança
1 Ao selecionar o menu Wi-Fi Direct, uma lista de dispositivos disponíveis será
Acessibilidade
exibida.
2 Quando a solicitação de conexão for exibida, selecione Sim. O dispositivo Wi-
Fi Direct estará conectado com sua TV.
* Somente dispositivos Wi-Fi Direct estarão disponíveis para conexão.

Ajustar Miracast
Miracast permite o compartilhamento de áudio e vídeo sem fio do dispositivo para a TV.
1 Ative a função Miracast no seu dispositivo.
2 Quando a TV detectar, selecione o seu dispositivo.
Quando a conexão estiver completa a tela do dispositivo será exibida na TV.

Por favor, entre em contato com o SAC para mais informações.

OWNER’S MANUAL

EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.

www.lg.com
 2 KEY CODES

KEY CODES
ENGLISH
ENG

• This feature is not available for all models.

Code Code
Function Note Function Note
(Hexa) (Hexa)
00 CH +, PR + R/C Button 53 List R/C Button
01 CH -, PR - R/C Button 5B Exit R/C Button
02 Volume + R/C Button 60 PIP(AD) R/C Button
03 Volume - R/C Button 61 Blue R/C Button
06 > (Arrow Key / Right Key) R/C Button 63 Yellow R/C Button
07 < (Arrow Key / Left Key) R/C Button 71 Green R/C Button
08 Power R/C Button 72 Red R/C Button
09 Mute R/C Button 79 Ratio / Aspect Ratio R/C Button
0B Input R/C Button 91 AD (Audio Description) R/C Button
0E SLEEP R/C Button 9E LIVE MENU R/C Button
0F TV, TV/RAD R/C Button 7A User Guide R/C Button
10 - 19 * Number Key 0 - 9 R/C Button 7C Smart / Home R/C Button
1A Q.View / Flashback R/C Button 7E SIMPLINK R/C Button
1E FAV (Favorite Channel) R/C Button 8E ►► (Forward) R/C Button
20 Text (Teletext) R/C Button 8F ◄◄ (Rewind) R/C Button
21 T. Opt (Teletext Option) R/C Button AA Info R/C Button
28 Return (BACK) R/C Button AB Program Guide R/C Button
30 AV (Audio / Video) Mode R/C Button B0 ► (Play) R/C Button
39 Caption/Subtitle R/C Button B1 ꕗ (Stop / File List) R/C Button
40 Λ (Arrow Key / Cursor Up) R/C Button B5 RECENT R/C Button
V (Arrow Key / Cursor ꕘ (Freeze / Slow Play /
41 R/C Button BA R/C Button
Down) Pause)
42 My Apps R/C Button BB Soccer R/C Button
43 Menu / Settings R/C Button BD ꔄ (REC) R/C Button
44 OK / Enter R/C Button DC 3D R/C Button
45 Q.Menu R/C Button 99 AutoConfig R/C Button
4C List, - (ATSC Only) R/C Button 9F App / * R/C Button
4D PICTURE R/C Button 9B TV / PC R/C Button
52 SOUND R/C Button

* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
 EXTERNAL CONTROL DEVICE SETUP 3

EXTERNAL CONTROL DEVICE SETUP

ENGLISH
ENG
• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

* Please be advised that not all models support this type of connectivity.
* Cable is not provided.

USB to Serial converter with USB Cable

USB Type

USB IN
(PC) (TV)

• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID :IN0x2008) USB to serial converter
RS-232C
which is not made nor provided by LG. (CONTROL & SERVICE)

(PC)
• It can be purchased from computer stores that carry accessories for IT support professionals. (TV)
RS-232C With RS232C Cable
USB IN

(PC)
DE9 (D-Sub 9pin) Type
1
(TV)
• You need to purchase the RS-232C (DE9, D-Sub 3 9pin female-to-female type) to RS-232C cable required
SERVICE ONLY

for the connection between the PC and the TV, which is specified in the manual.
(PC) (TV)
2 RS-232C IN
(CONTROL & SERVICE)

(PC) (TV)
1
3

(PC)
The connection interface may differ from your TV. 1 (TV)
SERVICE ONLY

3 RS-232C IN
(CONTROL & SERVICE)
2
(PC) (TV)
2

1
3

(PC) (TV)
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(CONTROL & SERVICE)

RS-232C IN
(CONTROL & SERVICE)
 IN IN
4 EXTERNAL CONTROL DEVICE SETUP
(PC) (TV)

USB USB
(PC) (TV)
Phone jack Type
ENGLISH

RS-232C IN
• You need to purchase the phone-jack to RS-232 cable required for &the connection between the PC and
ENG

(CONTROL SERVICE)

(PC)
the TV, which is specified in the manual. RS-232C IN
(CONTROL & SERVICE)
(TV)
(PC)
* For other models, connect to the USB port.
(TV)
* The connection interface may differ from your TV.

ONLY ONLY
3

(PC) 1
(TV)

SERVICE
3

(PC) (TV)

SERVICE
2

2
- or
1
3

(PC) 3
1 (TV)
RS-232C IN
(PC) 2
(CONTROL & SERVICE)
(TV)
RS-232C IN
(CONTROL & SERVICE)
2

Customer Computer RS-232C configurations

3-Wire Configurations(Not standard)
1 5 PC TV
RXD
RS-232C IN
2 2 TXD
(CONTROL & SERVICE)
TXD
RS-232C IN
3 1 RXD
(CONTROL & SERVICE)
GND 5 3 GND

6 9 OR
RS-232C RXD 3 2 TXD
(Serial port)
TXD 2 1 RXD
GND 5 3 GND
D-Sub 9 Phone

Set ID
For Set ID number, see "Real Data Mapping" on p.6

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
 EXTERNAL CONTROL DEVICE SETUP 5

Communication Parameters

ENGLISH
ENG
• Baud rate : 9600 bps (UART) • Stop bit : 1 bit
• Data length : 8 bits • Communication code : ASCII code
• Parity : None • Use a crossed (reverse) cable.

Command reference list

(Depending on model)

DATA DATA
COMMAND1 COMMAND2 COMMAND1 COMMAND2
(Hexadecimal) (Hexadecimal)
01. Power* k a 00 to 01 15. Balance k t 00 to 64
16. Color
02. Aspect
k c (p.7) (Colour) x u 00 to 64
Ratio
Temperature
17. ISM
03. Screen
k d (p.7) Method (Only j p (p.8)
Mute
Plasma TV)
04. Volume
k e 00 to 01 18. Equalizer j v (p.8)
Mute
05. Volume 19. Energy
k f 00 to 64 j q 00 to 05
Control Saving
20. Tune
06. Contrast k g 00 to 64 m a (p.9)
Command
21. Channel m b 00 to 01
07.
k h 00 to 64 (Programme)
Brightness
Add/Del(Skip)
08. Color/
k i 00 to 64 22. Key m c Key Codes
Colour
23. Control m g 00 to 64
Backlight,
09. Tint k j 00 to 64
Control Panel
Light
10. 24. Input x b (p.11)
k k 00 to 32
Sharpness select (Main)
11. OSD 25. 3D (Only x t (p.11)
k l 00 to 01
Select 3D models)
12. Remote 26. Extended x v (p.12)
Control Lock k m 00 to 01 3D (Only 3D
Mode models)
27. Auto j u (p.12)
13. Treble k r 00 to 64 Configure

14. Bass k s 00 to 64

* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
 6 EXTERNAL CONTROL DEVICE SETUP

Transmission / Receiving Protocol

ENGLISH
ENG

Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command 1] : First command to control the TV. (j, k, m or x)

[Command 2] : Second command to control the TV.
[Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ] : Space – ASCII code ‘0x20’

OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.

Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.

Data 00: Illegal Code

Real data mapping (Hexadecimal b Decimal)

* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 32 : Step 50 (Set ID 50) FE : Step 254
01 : Step 1 (Set ID 1) 33 : Step 51 (Set ID 51) FF : Step 255
... ... ...
0A : Step 10 (Set ID 10) 63 : Step 99 (Set ID 99) 01 00 : Step 256
... ... ...
0F : Step 15 (Set ID 15) C7 : Step 199 27 0E : Step 9998
10 : Step 16 (Set ID 16) C8 : Step 200 27 0F : Step 9999
... ... ...
 EXTERNAL CONTROL DEVICE SETUP 7

* Commands may work differently depending on model and signal.

ENGLISH
ENG
01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x]
►► To control Power *On or Off of the set.
* In case of video mute on only, TV will display On
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
Data 00 : Power Off 01 : *Power On

Ack [a][ ][Set ID][ ][OK/NG][Data][x]

04. Volume Mute (Command: k e)
►► To Show TV is Power On or *Off ►► To control volume mute on/off.
Transmission [k][a][ ][Set ID][ ][FF][Cr] You can also adjust mute using the MUTE button
on remote control.
Ack [a][ ][Set ID][ ][OK][Data][x]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
* Similarly, if other functions transmit ‘FF’ data
Data 00 : Volume mute on (Volume off)
based on this format, Acknowledgement feedback
01 : Volume mute off (Volume on)
presents status about each function.
Ack [e][ ][Set ID][ ][OK/NG][Data][x]

02. Aspect Ratio (Command: k c)

(Main Picture Size) 05. Volume Control (Command: k f)
►► To adjust the screen format. (Main picture format)
►► To adjust volume.
You can also adjust the screen format using the
You can also adjust volume with the volume
Aspect Ratio in the Q.MENU. or PICTURE menu.
buttons on remote control.
Transmission [k][c][ ][Set ID][ ][Data][Cr] Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data 01 : Normal screen 07 : 14:9 Data Min : 00 to Max : 64

(4:3) (Europe, Colombia, Mid-East, Ack [f][ ][Set ID][ ][OK/NG][Data][x]
02 : Wide screen Asia except South Korea and
(16:9) Japan)
04 : Zoom 09 : * Just Scan
05 : Zoom 2 0B : Full Wide 06. Contrast (Command: k g)
(Latin America (Europe, Colombia, Mid- ►► To adjust screen contrast.
except Colombia East, Asia except South You can also adjust contrast in the PICTURE
Only) Korea and Japan) menu.
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Original 0c : 21:9 (Depending on model)
Data Min : 00 to Max : 64
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition), 07. Brightness (Command: k h)
Just Scan is available. ►► To adjust screen brightness.
* Full wide mode may work differently based on You can also adjust brightness in the PICTURE
model and is supported for DTV fully, and ATV, menu.
AV partially. Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

03. Screen Mute (Command: k d) Ack [h][ ][Set ID][ ][OK/NG][Data][x]
►► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
 8 EXTERNAL CONTROL DEVICE SETUP

08. Color/Colour (Command: k i) 13. Treble (Command: k r)

ENGLISH

►► To adjust the screen Color(Colour). ►► To adjust treble.

ENG

You can also adjust colour in the PICTURE menu. You can also adjust in the AUDIO menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64 Data Min : 00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x] Ack [r][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j) * (Depending on model)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu. 14. Bass (Command: k s)
Transmission [k][j][ ][Set ID][ ][Data][Cr] ►► To adjust Bass.
You can also adjust in the AUDIO menu.
Data Red : 0
 0 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x] Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k) * (Depending on model)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE 15. Balance (Command: k t)
menu.
►► To adjust balance.
Transmission [k][k][ ][Set ID][ ][Data][Cr] You can also adjust balance in the AUDIO menu.
Data Min : 00 to Max : 32 Transmission [k][t][ ][Set ID][ ][Data][Cr]
Ack [k][ ][Set ID][ ][OK/NG][Data][x] Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]

11. OSD Select (Command: k l)

►► To select OSD (On Screen Display) on/off when 16. Color(Colour) Temperature (Command: x u)
controlling remotely.
►► To adjust colour temperature. You can also adjust
Transmission [k][l][ ][Set ID][ ][Data][Cr] Color(Colour) Temperature in the PICTURE menu.
Data 00 : OSD off 01 : OSD on Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]

12. Remote control lock mode (Command: k m)

►► To lock the front panel controls on the monitor and 17. ISM Method (Command: j p) (Only Plasma TV)
remote control. ►► To control the ISM method. You can also adjust
Transmission [k][m][ ][Set ID][ ][Data][Cr] ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off 01 : Lock on
Data Min : 02: Orbiter
Ack [m][ ][Set ID][ ][OK/NG][Data][x] 08: Normal
20: Color(Colour) Wash
* If you are not using the remote control, use this
mode. Ack [p][ ][Set ID][ ][OK/NG][Data][x]
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
 EXTERNAL CONTROL DEVICE SETUP 9

18. Equalizer (Command : j v) * Analog Antenna/Cable

ENGLISH
►► Adjust EQ of the set.

ENG
Transmission [j][v][ ][Set ID][ ][Data][Cr] [Data 00][Data 01] Channel Data
Data 00 : High byte channel data
MSB LSB
Data 01 : Low byte channel data
0 0 0 0 0 0 0 0 - 00 00 ~ 00 C7 (Decimal : 0 ~ 199)

Data 02 : Input Source (Analog)

Frequency Data - 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
7 6 5 Frequency 4 3 2 1 0 Step * Digital Antenna/Cable/Satellite
0 0 0 1st Band 0 0 0 0 0 0(decimal) [Data 00][Data 01]: Channel Data
0 0 1 2nd Band 0 0 0 0 1 1(decimal) Data 00 : High Channel data
0 1 0 3rd Band ... ... ... ... ... ... Data 01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
0 1 1 4th Band 1 0 0 1 1 19(decimal)
Data 02 : Input Source (Digital)
1 0 0 5th Band 1 0 1 0 1 20(decimal) - 10 : Antenna TV (DTV)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] - 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
* It depends on model, and can adjust when sound - 50 : Satellite Radio (S-Radio)
mode is EQ adjustable value. - 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
19. Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You * Tune Command Examples:
can also adjust Energy Saving in PICTURE menu. 1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data 00 & 01 = Channel Data is 10 = 00 0a
Data Data 02 = Analog Antenna TV = 00
00 : Off Result = ma 00 00 0a 00
01 : Minimum
02 : Medium 2. Tune to the digital antenna (DVB-T) Channel 01.
03 : Maximum Set ID = All = 00
04 : Auto (For LCD TV / LED TV) / Data 00 & 01 = Channel Data is 1 = 00 01
Intelligent sensor (For PDP TV) Data 02 = Digital Antenna TV = 10
05 : Screen off Result = ma 00 00 01 10
* (Depending on model) 3. Tune to the satellite (DVB-S) Channel 1000.
Ack [q][ ][Set ID][ ][OK/NG][Data][x] Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
20. Tune Command (Command: m a)
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
* This command may work differently depending on
model and signal. [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For Europe, Mid-East, Colombia, Asia except • For South Korea, North/Latin America except
South Korea and Japan Model Colombia Model
►► Select channel to following physical number. ►► To tune channel to following physical/major/minor
Transmission [m][a][ ][Set ID][ ][Data 00][ ] number.
[Data 01][ ][Data 02][Cr] Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
 10 EXTERNAL CONTROL DEVICE SETUP

* Analog Antenna/Cable 2. Tune to the digital antenna (ATSC) channel 30-3.

ENGLISH

Set ID = All = 00
ENG

Data 00 : Physical Channel Number Data 00 = Don’t know Physical = 00

- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) Data 01 & 02 = Major is 30 = 00 1E
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125) Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
[Data 01 ~ 04]: Major/Minor Channel Number Total = ma 00 00 00 1E 00 03 22
Data 01 & 02: xx (Don't care)
Data 03 & 04: xx (Don't care) Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
Data 05: Input Source (Analog) [Data 02][Data 03][Data 04][Data 05]
- 00 : Antenna TV (ATV) [x][a][ ][Set ID][ ][NG][Data 00][x]
- 01 : Cable TV (CATV)
• For Japan Model
►► To tune channel to following physical/major/minor
* Digital Antenna/Cable
number.
Data 00 : xx (Don't care) Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data * Digital Antenna/Satellite
Data 02 : Low byte Channel Data Data 00: xx (Don't care)
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number [Data 01][Data 02]: Major Channel Number
Data 03 : High byte Channel Data Data 01: High byte Channel Data
Data 04 : Low byte Channel Data Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
Data 05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel [Data 03][Data 04]: Minor/Branch Channel Number
Number (Don’t care in Satellite)
- 06 : Cable TV (CADTV) – Use Physical Channel Data 03: High byte Channel Data
Number Data 04: Low byte Channel Data
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number Data 05 : Input Source (Digital/Satellite for Japan)
- 26 : Cable TV (CADTV) - Don’t Use Physical - 02 : Antenna TV (DTV)
Channel Number - 42 : Antenna TV (DTV) – Use Physical/Major
- 46 : Cable TV (CADTV) – Use Physical/Major Channel Number Only (One Part Channel)
Channel Number Only (One Part Channel) - 62 : Antenna TV (DTV) – Use Major Channel
- 66 : Cable TV (CADTV) – Use Major Channel Number Only (One Part Channel)
Number Only (One Part Channel) - 07 : BS (Broadcasting Satellite)
- 0b : Cable DTV Plus – Use Physical Channel - 08 : CS1 (Communication Satellite 1)
Number - 09 : CS2 (Communication Satellite 2)
- 2b : Cable DTV Plus – Don’t Use Physical
Channel Number * Tune Command Examples:
- 4b : Cable DTV Plus – Use Physical/Major 1 Tune to the digital antenna (ISDB-T) channel 17-1.
Channel Number Only (One Part Channel) Set ID = All = 00
- 6b : Cable DTV Plus – Use Major Channel Data 00 = Don’t know Physical = 00
Number Only (One Part Channel) Data 01 & 02 = Major is 17 = 00 11
Two bytes are available for each major and minor Data 03 & 04 = Minor/Branch is 1 = 00 01
channel data, but usually the low byte is used alone Data 05 = Digital Antenna TV = 02
(high byte is 0). Total = ma 00 00 00 11 00 01 02
* Tune Command Examples:
1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
 EXTERNAL CONTROL DEVICE SETUP 11

2. Tune to the BS (ISDB-BS) channel 30. 24. Input select (Command: x b)

ENGLISH
Set ID = All = 00 (Main Picture Input)

ENG
Data 00 = Don’t know Physical = 00 ►► To select input source for main picture.
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00 Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 05 = Digital BS TV = 07
Data
Total = ma 00 00 00 1E 00 00 07
00 : DTV 01 : CADTV
* This feature is varied based on the model. 02 : Satellite DTV 10 : ATV
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
[Data 02][Data 03][Data 04][Data 05] 04 : ISDB-CS2 (Japan)
[x][a][ ][Set ID][ ][NG][Data 00][x] 11 : CATV
20 : AV or AV1 21 : AV2
40 : Component1 41 : Component2
21. Channel(Programme) Add/Del(Skip) 60 : RGB
(Command: m b) 90 : HDMI1 91 : HDMI2
►► To skip current channel(programme) for next time. 92 : HDMI3 93 : HDMI4
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
* This function depends on model and signal.
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
25. 3D(Command: x t) (only 3D models)
* Set the saved channel status to del(ATSC, ISDB)/ (Depending on model)
skip(DVB) or add. ►► To change 3D mode for TV.

22. Key (Command: m c) Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
►► To send IR remote key code. [ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Structure
[Data 00] 00 : 3D On
Data Key code - p.2. 01 : 3D Off
02 : 3D to 2D
Ack [c][ ][Set ID][ ][OK/NG][Data][x] 03 : 2D to 3D
[Data 01] 00 : Top and Bottom
23. Control Backlight (Command: m g)
01 : Side by Side
• For LCD TV / LED TV 02 : Check Board
►► To control the backlight. 03 : Frame Sequential
Transmission [m][g][ ][Set ID][ ][Data][Cr] 04 : Column interleaving
05 : Row interleaving
Data Min : 00 to Max : 64 [Data 02] 00 : Right to Left
01 : Left to Right
Ack [g][ ][Set ID][ ][OK/NG][Data][x] [Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14
Control Panel Light (Command: m g) (*transmit by Hexadecimal code)

• For Plasma TV
►► To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

 12 EXTERNAL CONTROL DEVICE SETUP

* [Data 02], [Data 03] functions depend on model 3) When [Data 00] is 06, 07
ENGLISH

and signal. 00 : Off

ENG

* If [Data 00] is 00 (3D On), [Data 03] has no 01 : On

meaning.
4) When [Data 00] is 08
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
00 : Revert to 3D video from 3D-to-2D
01], [Data 02] and [Data 03] have no meaning.
converted 2D video
* If [Data 00] is 03 (2D to 3D), [Data 01] and 01 : Change 3D video to 2D video, except
[Data 02] have no meaning. 2D-to-3D video
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data * If conversion condition doesn’t meet, command is
03] works when 3D Mode (Genre) is manual only. treated as NG.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal. 5) When [Data 00] is 09
00 : Standard 01 : Sport
[Data 00] [Data 01] [Data 02] [Data 03] 02 : Cinema 03 : Extreme
00 O O O 04 : Manual 05 : Auto

01 X X X Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]

02 X X X [v][ ][Set ID][ ][NG][Data00][x]
03 X O O
27. Auto Configure (Command: j u)
X : don’t care
(Depending on model)
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] ►► To adjust picture position and minimize image
[Data03][x] shaking automatically. It works only in RGB (PC)
mode.
[t][ ][Set ID][ ][NG][Data00][x]
Transmission [j][u][ ][Set ID][ ][Data][Cr]
26. Extended 3D(Command: x v) (only 3D models) Data 01 : To set Auto Configure
(Depending on model)
►► To change 3D option for TV. Ack [u][ ][Set ID][ ][OK/NG][Data][x]

Transmission [x][v][ ][Set ID][ ][Data 00][ ]

[Data 01][Cr]
[Data 00] 3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)

[Data 01] It has own range for each 3D option

determined by [Data 00].
1) When [Data 00] is 00
00 : Right to Left
01 : Left to Right

2) When [Data 00] is 01, 02

Data Min: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.