One-channel Ignition Device

ONE-CHANNEL IGNITION DEVICE

P/N 81550.01
Technical specifications

Purpose of the product

The P/N 81550.01 ignition device is designed to create voltage impulses for the spark
plug, the resultant sparks in the gap of the plug the ignite a mixture of fuel and air in
the combustion chamber of a turbojet engine.

2/8 Aerospace Technology Division

One-channel Ignition Device

Technical data
› Technical parameters

Nominal voltage ..................................... 28 V DC

Nominal current consumption ................. < 1,5 A
Operating voltage ................................... 14 V DC ÷ 30 V DC *1.)
Output voltage ........................................ 2.5 ÷ 3 kV
Supplied energy ..................................... > 0.6 J / channel
Discharge frequency at 14 V DC ............ 3 Hz ÷ 6 Hz
Discharge frequency at 30 V DC ............ 4 Hz ÷ 7 Hz
Operating temperature .......................... -55 ÷ 100 °C
Weight .................................................... ≤ 0,6 kg
Operational mode .................................. Intermittent (designed also for continuous
operation)
1.
* ) The minimum allowable voltage is 12V DC, with a proportional reduction in discharge
frequency compared with the discharge frequency at 14 V DC.

› Operating conditions

Requirements for resistance to external influences are based on RTCA/DO-160E

documentation and the ISO 2678 standard in the categories detailed in the table
below. Any tests marked with an X are not necessary.

Section Environmental Conditions Categories

4 Temperature and Altitude C3
5 Temperature Variation B
6 Humidity C
7 Operational Shocks and Crash Safety 6g/11ms
8 Vibration W curve
9 Proof against Explosion X
10 Waterproofness W
11 Fluid Susceptibility F
12 Resistance to Sand and Dust D
13 Resistance to Fungus F
14 Resistance to Salt Spray S
15 Magnetic Effects Z
16 Power Input Z
17 Voltage Spikes A
18 Audio Frequency Conducted Susceptibility Z
19 Induced Signal Susceptibility Z
Radio Frequency Susceptibility
20 T
(Radiated and Conducted)
Emission of Radio Input L
21
Frequency Energy Output B
22 Lightning Induced Transient Susceptibility XXC2
23 Lightning Direct Effects X
24 Icing Test A
25 Electrostatic Discharge X
3/8 Aerospace Technology Division
One-channel Ignition Device

› Installation dimension

4/8 Aerospace Technology Division

One-channel Ignition Device

Technical description
› Description of the P/N 81550.01 ignition device

The P/N 81550.01 is a one-channel ignition device. This is an electrical unit

containing electronic circuits for converters on printed circuit boards that are
connected with inherent main elements fastened on a bearing structure. This
structure is placed in a metal box and embedded in foam. The box is tightly sealed
and soldered. The box is equipped with a connector for supply voltage and one
connector for attaching connecting cables. The base plate of the ignition device has
four holes for fastening the device to the frame.

› Description of function

The ignition device is formed by a freely oscillating converter which charges a

capacitor. When a flashover voltage of the internal gap is reached, the energy
accumulated in the capacitor discharges in the spark plug. The frequency of
discharge depends on the supply voltage; at 14 V it has a value of min. 3 Hz, while at
30 V it is a maximum of 7 Hz.

Other data
› Product marking

Two labels in English are adhered to the ignition device, detailing the type of unit and
a warning. The type label contains the following data: the company logo, product
name, type designation (P/N) and serial number (S/N) containing the six-digit number
of the order, a dot, and a two-digit ordinal number in the order. After this an area is
reserved for identifying any revisions – see the picture below.
The warning label warns of the presence of high voltage; prior to maintenance it is
necessary to disconnect the device from the supply voltage.

Type label Warning label

5/8 Aerospace Technology Division

One-channel Ignition Device

Instructions for use

› For installation dimensions, see the Installation Dimensions section.
› When installing the ignition device, it is necessary to ensure correct polarity of
the ignition wiring (see Installation Dimensions).
› When installing the ignition device, at least one fastening point must be reliably
(electrically) connected to the frame of the engine.
› The recommended intermittent mode consists of 30 seconds of operation + 2.5
minutes of rest. However the device can be used continuously if needed (e.g.
when flying in rain).
› No setting has to be made and no special tools or jigs are required during
installation.

Maintenance instructions
› The ignition device does not require any special operation and maintenance
when in use.
› Once the time to overhaul is reached, it is necessary to send the device to the
manufacturer for such maintenance.

Service life, guarantees

› Service life
Time to overhaul
 8 years or
 3,000 starts with 30 s duration, i.e. 90,000 seconds (25 hours) in total,
whichever comes first

Expected service life

 25 years or
 9,000 starts with 30 s duration, i.e. 270,000 seconds (75 hours) in total,
whichever comes first

› Guarantees
The Supplier guarantees failure-free operation of the product for a period of 12
months or 500 starts from the moment of commissioning at the Customer,
whichever comes first. The Manufacturer guarantees failure-free operation only
if the installation instructions, installation conditions and operating conditions
specified in these Technical Specifications are met.

6/8 Aerospace Technology Division

One-channel Ignition Device

Repair instructions
› The ignition device is an electrical unit that cannot be repaired or
disassembled.

Ordering products
› The purchaser is required to state precise data in their order, in particular:
 The P/N 81550.01 ignition device
 The number of pieces
 The method of conservation (short-term or long-term). If the conservation
method is not stated in the order, the product will be delivered with short-
term conservation.
 The language of the accompanying documents shall be in English .

P/N 81550.01 Ignition Device delivery

› Full delivery includes the following:
 P/N 81550.01 Ignition Device 1 pc
 No spare parts are delivered with the product
 No tools are delivered with the product
 The delivery includes the following accompanying documentation –
Certificate of Quality and Completeness

7/8 Aerospace Technology Division