Mhandisi Consultancy Ltd Julius Nyerere Hydropower Project

EMPLOYER

THE UNITED REPUBLIC OF TANZANIA

TANZANIA ELECTRIC SUPPLY

COMPANY LIMITED
EMPLOYER REPRESENTATIVE

TANROADS ENGINEERING CONSULTING UNIT

(TECU)
EPC CONTRACTOR

JOINT VENTURE OF

PROJECT

Julius Nyerere Hydropower Project - JNHPP

Internal Review Document Release

D 09/03/2021 Issued For Approval

C 18/02/2021 Issued For Approval

02 10-03-2021 For Review MCL MCL MCL
B 03/12/2020 Issued For Approval 01 22-02-2021 For Review MCL MCL MCL
A 17/09/2020 Issued For Approval
00 03-12-2020 For Review MCL MCL MCL

Ver Date Version Detail Rev Date Revision Details Checked Approved Approved

Scale: 1/100 Type: A4/Black Phase: Construction Discipline: civil Contract/PO /7000-CA-000009

Originator Title

ADMINISTRATION AND OPERATION

BUILDING - STRUCTURAL DESIGN
CALCULATIONS REPORT
Copyright © JV. of The Arab Contractors & Elsewedy Rev/Ver
Document No.
Electric All rights reserved. The reproduction, disclosure
or use of this document or its contents is forbidden 7000-MCL500-UZW-&CED010-000660 02
without express written authority from The Arab
Page
Contractors & Elsewedy Electric.
1/335
 THE UNITED REPUBLIC OF TANZANIA
MINISTRY OF ENERGY

TANZANIA ELECTRIC SUPPLY COMPANY LIMITED

(TANESCO)

PROVISION OF CONSULTANCY SERVICES FOR COMPLETE ENGINEERING

WORKS FOR THE CIVIL, MECHANICAL AND ELECTRICAL WORKS OF
EMPLOYER OPERATIONAL VILLAGE OF THE JNHPP

ADMINISTRATION AND OPERATION BUILDING STRUCTURAL DESIGN

CALCULATIONS REPORT

MARCH 2021

MHANDISI CONSULTANCY LTD

Plot No. 305B, Mikocheni
P. O. Box 12965,
Dar es Salaam, Tanzania.
Provision of Consultancy Services for Complete Engineering Works for the Civil, Mechanical and Administration and Operation Building
Electrical Works of Employer Operational Village of the JNHPP Structural Design Calculations

Contents

1. INTRODUCTION ......................................................................................................................................... 2
2. GENERAL ASSUMPTIONS & GIVEN PARAMETERS ........................................................................ 2
3. APPENDIX I ................................................................................................................................................. 4

February 2021 P a g e |1
Provision of Consultancy Services for Complete Engineering Works for the Civil, Mechanical and Administration and Operation Building
Electrical Works of Employer Operational Village of the JNHPP Structural Design Calculations

1. Introduction
This documentation contains the structural design calculations for the Administration and Operation
Building of the Proposed Employer Operational Village of the Julius Nyerere Hydropower Project
(JNHPP) Power Generation 2115 MW and Flood Control as per municipal requirements and basing
on the architectural plans/drawings

2. General Assumptions & Given Parameters

The general assumption and given parameters are in refence to the design criterial submitted

2.1 Soil Properties:

Soil properties are based on the submitted draft geotechnical report however for the missing information
the flowing were assumed:

Density of soil; γsoil = 18.0 kN/m3

Design shear strength; φ = 22.6 deg
Design base friction; ɗ = 19.3 deg

2.2 Loading :

Loading loading is per the submitted design critertial for Structural engineering services, however the
following valuess have been considered basing on the analysis carried accordingly:
Roof Imposed Load qk = 0.4 kN/m2
First Floor Imposed Load qk = 5.0KN/m2, 1.5KN/m2
Staircase Imposed Load qk = 2.0KN/m2
First Floor Finishes qk = 1.20KN/m2
Staircase Finishes gk = 1.2KN/m2

2.3 Structural

The structure is Frame consisting generally of 150 and 175mm floor slab on 230x500 and 300x500
respectively reinforced concrete beams, 230x230mm and 300x300mm columns on pad bases with
230mm thick solid blockwork on 230mm thick strip footing.

2.4 Material Properties

The material properties used are in line with the submitted design criterial for Structural engineering
services as detailed here under.

Concrete strength : Grade 25 MPa

Steel reinfocement: Grade 500 MPa
Structural steel: Grade 275 MPa
Fire Resistance 1 Hour to all Elements.

February 2021 P a g e |2
Provision of Consultancy Services for Complete Engineering Works for the Civil, Mechanical and Administration and Operation Building
Electrical Works of Employer Operational Village of the JNHPP Structural Design Calculations

2.5 Design Codes and Manual:

Combination of Eurocode and British Standards Design Codes and Manual have been used on different
elements of the structures accordingly

2.6 Exposure Condition:

Th structure have been designed considering/assuming that there is no significant freeze/thaw, abrasion
or chemical attack and the foundation will be permenently dry as per the geotechnical investiagton
report.

February 2021 P a g e |3
Provision of Consultancy Services for Complete Engineering Works for the Civil, Mechanical and Administration and Operation Building
Electrical Works of Employer Operational Village of the JNHPP Structural Design Calculations

3. Appendix I

February 2021 P a g e |4
Provision of Consultancy Services for Complete Engineering Works for the Civil, Mechanical and Administration and Operation Building
Electrical Works of Employer Operational Village of the JNHPP Structural Design Calculations

3.1 Design Calculations

February 2021 P a g e |5
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

STEEL MEMBER ANALYSIS & DESIGN (EN1993-1-1:2005)

In accordance w ith EN1993-1-1:2005 incorporating Corrigenda February 2006 and April 2009 and the UK national
annex
Tedds calculation version 4.4.05

ANALYSIS
Tedds calculation version 1.0.35

Results
Total deflection
1.35G + 1.5Q + 1.5RQ (Strength) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results
Load combination: 1.35G + 1.5Q + 1.5RQ (Strength)
Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 9.739 0.5 16.58 0 12.375 0.1 2.25 0
Left Rafter 8.995 0.7 1.218 0 1.197 0 9.578 -0.1
Right Rafter 1.79 0.8 8.339 0 0 0.2 4.789 0.1
1.0G + 1.0Q + 1.0RQ (Service) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results
Load combination: 1.0G + 1.0Q + 1.0RQ (Service)
Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 9.732 0.3 16.584 0 12.375 0.1 2.25 0
Left Rafter 8.995 0.5 1.217 0 1.197 0 9.578 -0.1
Right Rafter 1.79 0.5 8.338 0 0 0.1 4.789 0.1
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

1.35G + 1.5Q + 1.5 0 S + 1.5 0 W (Strength) - Total deflection

25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results

Load combination: 1.35G + 1.5Q + 1.5 0 S + 1.5 0 W (Strength)

Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.445 0.4 16.588 0 15.75 0.1 2.25 0
Left Rafter 9.578 0.3 1.214 0 1.197 0 9.578 0
Right Rafter 0.579 0.8 8.339 0 0 0.2 8.38 0.1
1.0G + 1.0Q + 0.5S + 0.5W (Service) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results
Load combination: 1.0G + 1.0Q + 0.5S + 0.5W (Service)
Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.452 0.3 16.591 0 12.375 0.1 2.25 0
Left Rafter 9.578 0.2 1.214 0 1.197 0 9.578 0
Right Rafter 0.579 0.6 8.339 0 0 0.1 4.789 0.1
1.35G + 1.5 0 Q + 1.5S + 1.5 0 W (Strength) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results

Load combination: 1.35G + 1.5 0 Q + 1.5S + 1.5 0 W (Strength)

 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Member Deflection Axial deflection

Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.512 0.3 16.602 0 15.75 0.1 2.25 0
Left Rafter 9.578 0.3 0 0 1.197 0 9.578 0
Right Rafter 0.573 0.6 8.339 0 0 0.1 8.38 0.1
1.0G + 1.0 0 Q + 1.0S + 0.5W (Service) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results

Load combination: 1.0G + 1.0 0 Q + 1.0S + 0.5W (Service)

Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.514 0.2 16.606 0 15.75 0 2.25 0
Left Rafter 9.578 0.2 0 0 1.197 0 9.578 0
Right Rafter 0.574 0.4 8.339 0 0 0.1 8.38 0
1.35G + 1.5 0 Q + 1.5 0 S + 1.5W (Strength) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results

Load combination: 1.35G + 1.5 0 Q + 1.5 0 S + 1.5W (Strength)

Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.636 0.3 3.308 -0.2 15.75 0 6.75 0
Left Rafter 9.578 0.1 9.039 -0.4 5.986 0.1 1.197 0
Right Rafter 0.553 0.7 8.34 0 0 0.1 8.38 0
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

1.0G + 1.0 0 Q + 0.5S + 1.0W (Service) - Total deflection

25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results

Load combination: 1.0G + 1.0 0 Q + 0.5S + 1.0W (Service)

Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 10.628 0.2 3.318 -0.1 15.75 0 6.75 0
Left Rafter 9.578 0.1 9.04 -0.3 5.986 0 1.197 0
Right Rafter 0.554 0.5 8.34 0 0 0.1 8.38 0
1.0G + 1.5W (Strength) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results
Load combination: 1.0G + 1.5W (Strength)
Member Deflection Axial deflection
Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 17.632 0.1 3.167 -0.4 2.25 0 6.75 -0.1
Left Rafter 1.22 0 9.025 -0.9 5.986 0.1 1.197 0
Right Rafter 0.509 0.3 0 -0.1 0 0 8.38 0
1.0G + 1.0W (Service) - Total deflection
25
24 26
23 27
22 28
21 29
20 30
19 31
18 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
X

Member results
Load combination: 1.0G + 1.0W (Service)
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Member Deflection Axial deflection

Pos Max Pos Min Pos Max Pos Min
(m) (mm) (m) (mm) (m) (mm) (m) (mm)
Bottom Chord1 17.628 0.1 3.246 -0.2 2.25 0 6.75 -0.1
Left Rafter 1.22 0 9.026 -0.5 5.986 0.1 1.197 0
Right Rafter 0.518 0.2 0 -0.1 0 0 8.38 0
;
Partial factors - Section 6.1
Resistance of cross-sections;  M0 = 1
Resistance of members to instability;  M1 = 1
Resistance of tensile members to fracture;  M2 = 1.1

Bottom Chord1 - Span 1 design

Section details
Section type; CHS 42.4x2.6 (Tata Steel Celsius)
Steel grade - EN 10210-1:2006; S275H
Nominal thickness of element; tnom = t = 2.6 mm
Nominal yield strength; fy = 275 N/mm 2
Nominal ultimate tensile strength; fu = 410 N/mm 2
Modulus of elasticity; E = 210000 N/mm 2

Bottom Chord1 span 1 results summary Unit Capacity Maximum Utilisation Result
Shear resistance (y-y) kN 32.9 0.1 0.003 PASS
Bending resistance (y-y) kNm 1.1 0.1 0.058 PASS
Compression resistance kN 64.5 1.1 0.017 PASS
Tension resistance kN 89.4 1.4 0.015 PASS
Comb. bending and axial force 0.058 PASS
Deflection (y-y) mm 6.3 0.2 0.033 PASS

Lateral restraint
Section has lateral restraint at supports only

Consider Combination 9 - 1.0G + 1.5W (Strength)

Classification of cross sections - Section 5.5
 = [235 N/mm 2 / f y] = 0.92

Tubular sections - Table 5.2 (sheet 3 of 3)

d / t = 16.3 = 19.1 *  2 <= 50 *  2 ; Class 1
Section is class 1
Check tension - Section 6.2.3
Design tension force; N Ed = 1.4 kN
Design resistance of section - eq 6.6; N t,Rd = N pl,Rd = A * fy /  M0 = 89.4 kN
N Ed / N t,Rd = 0.015
PASS - Design tension resistance exceeds design tension

Check design at start of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0.1 kN
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2

Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.003
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0.1 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.058
PASS - Design bending resistance moment exceeds design bending moment
Check bending and axial force - Section 6.2.9
Normal force to plastic resistance force ratio; n = N Ed / N pl,Rd = 0.015
Reduced plastic moment resistance - Eq.6.39; M N,y,Rd = M pl,y,Rd * (1 - n 1.7 ) = 1.1 kNm
M y,Ed / M N,y,Rd = 0.058
PASS - Reduced bending resistance moment exceeds design bending moment

Check design at end of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0.1 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.002
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.02
PASS - Design bending resistance moment exceeds design bending moment

Consider Combination 10 - 1.0G + 1.0W (Service)

Check design 337 mm along span

Check y-y axis deflection - Section 7.2.1
Maximum deflection;  y = 0.2 mm
Allowable deflection;  y,Allowable = L m1_s1 / 180 = 6.3 mm
 y /  y,Allowable = 0.033
PASS - Allowable deflection exceeds design deflection

Bottom Chord1 - Span 2 design

Section details
Section type; CHS 42.4x2.6 (Tata Steel Celsius)
Steel grade - EN 10210-1:2006; S275H
Nominal thickness of element; tnom = t = 2.6 mm
Nominal yield strength; fy = 275 N/mm 2
Nominal ultimate tensile strength; fu = 410 N/mm 2
Modulus of elasticity; E = 210000 N/mm 2

Bottom Chord1 span 2 results summary Unit Capacity Maximum Utilisation Result
Shear resistance (y-y) kN 32.9 0.0 0.001 PASS
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Bending resistance (y-y) kNm 1.1 0.0 0.021 PASS

Compression resistance kN 4.0 2.4 0.585 PASS
Tension resistance kN 89.4 2.1 0.023 PASS
Comb. bending and axial force 0.586 PASS
Deflection (y-y) mm 15.6 0.3 0.017 PASS

Lateral restraint
Section has lateral restraint at supports only

Consider Combination 9 - 1.0G + 1.5W (Strength)

Classification of cross sections - Section 5.5
 = [235 N/mm 2 / f y] = 0.92

Tubular sections - Table 5.2 (sheet 3 of 3)

d / t = 16.3 = 19.1 *  2 <= 50 *  2 ; Class 1
Section is class 1
Check tension - Section 6.2.3
Design tension force; N Ed = 1.4 kN
Design resistance of section - eq 6.6; N t,Rd = N pl,Rd = A * fy /  M0 = 89.4 kN
N Ed / N t,Rd = 0.015
PASS - Design tension resistance exceeds design tension

Check design at start of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.02
PASS - Design bending resistance moment exceeds design bending moment
Check bending and axial force - Section 6.2.9
Normal force to plastic resistance force ratio; n = N Ed / N pl,Rd = 0.015
Reduced plastic moment resistance - Eq.6.39; M N,y,Rd = M pl,y,Rd * (1 - n 1.7 ) = 1.1 kNm
M y,Ed / M N,y,Rd = 0.02
PASS - Reduced bending resistance moment exceeds design bending moment

Check design 1125 mm along span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 8
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Check bending moment - Section 6.2.5

Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.011
PASS - Design bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = 0.004 kNm / 0.022 kNm = 0.182
 y = 0.001 kNm / 0.022 kNm = 0.045
C my = max(0.2 + 0.8 *  y, 0.4) = 0.400
;  LT = 0.004 kNm / 0.022 kNm = 0.182
 LT = 0.001 kNm / 0.022 kNm = 0.045
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.400

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.576
k zy = 0.6 * k yy = 0.346
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.557
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.038
PASS - Combined bending and compression checks are satisfied

Check design 2250 mm along span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.002
PASS - Design bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = 0.004 kNm / 0.022 kNm = 0.182
 y = 0.001 kNm / 0.022 kNm = 0.045
C my = max(0.2 + 0.8 *  y, 0.4) = 0.400
;  LT = 0.004 kNm / 0.022 kNm = 0.182
 LT = 0.001 kNm / 0.022 kNm = 0.045
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.400

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 9
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm

Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.587
k zy = 0.6 * k yy = 0.352
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.586
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.037
PASS - Combined bending and compression checks are satisfied

Consider Combination 2 - 1.0G + 1.0Q + 1.0RQ (Service)

Check design 1835 mm along span

Check y-y axis deflection - Section 7.2.1
Maximum deflection;  y = 0.3 mm
Allowable deflection;  y,Allowable = L m1_s2 / 360 = 15.6 mm
 y /  y,Allowable = 0.017
PASS - Allowable deflection exceeds design deflection

Bottom Chord1 - Span 3 design

Section details
Section type; CHS 42.4x2.6 (Tata Steel Celsius)
Steel grade - EN 10210-1:2006; S275H
Nominal thickness of element; tnom = t = 2.6 mm
Nominal yield strength; fy = 275 N/mm 2
Nominal ultimate tensile strength; fu = 410 N/mm 2
Modulus of elasticity; E = 210000 N/mm 2

Bottom Chord1 span 3 results summary Unit Capacity Maximum Utilisation Result
Shear resistance (y-y) kN 32.9 0.0 0.001 PASS
Bending resistance (y-y) kNm 1.1 0.0 0.011 PASS
Compression resistance kN 2.8 1.0 0.337 PASS
Tension resistance kN 89.4 1.5 0.017 PASS
Comb. bending and axial force 0.341 PASS
Deflection (y-y) mm 18.8 0.3 0.018 PASS

Lateral restraint
Section has lateral restraint at supports only

Consider Combination 1 - 1.35G + 1.5Q + 1.5RQ (Strength)

Classification of cross sections - Section 5.5
 = [235 N/mm 2 / f y] = 0.92

Tubular sections - Table 5.2 (sheet 3 of 3)

d / t = 16.3 = 19.1 *  2 <= 50 *  2 ; Class 1
Section is class 1
Check compression - Section 6.2.4
Design compression force; N Ed = 0.9 kN
Design resistance of section - eq 6.10; N c,Rd = N pl,Rd = A * f y /  M0 = 89.4 kN
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 10
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

N Ed / N c,Rd = 0.01
PASS - Design compression resistance exceeds design compression
Slenderness ratio for y-y axis flexural buckling - Section 6.3.1.3
Critical buckling length; L cr,y = L m1_s3 = 6750 mm
Critical buckling force; N cr,y =  2 * E * I y / L cr,y2 = 2.9 kN
Slenderness ratio for buckling - eq 6.50;  y = (A * f y / N cr,y) = 5.514

Check y-y axis flexural buckling resistance - Section 6.3.1.1

Buckling curve - Table 6.2; a
Imperfection factor - Table 6.1;  y = 0.21
Buckling reduction determination factor; y = 0.5 * (1 +  y * ( y - 0.2) +  y2 ) = 16.259
Buckling reduction factor - eq 6.49;  y = min(1 / (y + (y2 -  y2 )), 1) = 0.032
Design buckling resistance - eq 6.47; N b,y,Rd =  y * A * fy /  M1 = 2.8 kN
N Ed / N b,y,Rd = 0.327
PASS - Design buckling resistance exceeds design compression
Slenderness ratio for z-z axis flexural buckling - Section 6.3.1.3
Critical buckling length; L cr,z = L m1_s3_seg1 = 6750 mm
Critical buckling force; N cr,z =  2 * E * I z / L cr,z 2 = 2.9 kN
Slenderness ratio for buckling - eq 6.50;  z = (A * f y / N cr,z ) = 5.514

Check z-z axis flexural buckling resistance - Section 6.3.1.1

Buckling curve - Table 6.2; a
Imperfection factor - Table 6.1;  z = 0.21
Buckling reduction determination factor; z = 0.5 * (1 +  z * ( z - 0.2) +  z 2) = 16.259
Buckling reduction factor - eq 6.49;  z = min(1 / (z + (z 2 -  z 2 )), 1) = 0.032
Design buckling resistance - eq 6.47; N b,z,Rd =  z * A * f y /  M1 = 2.8 kN
N Ed / N b,z,Rd = 0.327
PASS - Design buckling resistance exceeds design compression

Check design at start of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.011
PASS - Design bending resistance moment exceeds design bending moment
Check bending and axial force - Section 6.2.9
Normal force to plastic resistance force ratio; n = N Ed / N pl,Rd = 0.01
Reduced plastic moment resistance - Eq.6.39; M N,y,Rd = M pl,y,Rd * (1 - n 1.7 ) = 1.1 kNm
M y,Ed / M N,y,Rd = 0.011
PASS - Reduced bending resistance moment exceeds design bending moment
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 11
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Check combined bending and compression - Section 6.3.3

Equivalent uniform moment factors - Table B.3;  y = -0.009 kNm / -0.013 kNm = 0.692
 y = -0.002 kNm / -0.013 kNm = 0.154
C my = max(0.2 + 0.8 *  y, 0.4) = 0.400
;  LT = -0.009 kNm / -0.013 kNm = 0.692
 LT = -0.002 kNm / -0.013 kNm = 0.154
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.400

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.505
k zy = 0.6 * k yy = 0.303
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.333
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.331
PASS - Combined bending and compression checks are satisfied

Check design 1634 mm along span

Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.004
PASS - Design bending resistance moment exceeds design bending moment

Check design at end of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.008
PASS - Design bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = -0.009 kNm / -0.013 kNm = 0.692
 y = -0.002 kNm / -0.013 kNm = 0.154
C my = max(0.2 + 0.8 *  y, 0.4) = 0.400
;  LT = -0.009 kNm / -0.013 kNm = 0.692
 LT = -0.002 kNm / -0.013 kNm = 0.154
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.400
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 12
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.508
k zy = 0.6 * k yy = 0.305
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.341
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.34
PASS - Combined bending and compression checks are satisfied

Consider Combination 2 - 1.0G + 1.0Q + 1.0RQ (Service)

Check design 2982 mm along span

Check y-y axis deflection - Section 7.2.1
Maximum deflection;  y = 0.3 mm
Allowable deflection;  y,Allowable = L m1_s3 / 360 = 18.8 mm
 y /  y,Allowable = 0.018
PASS - Allowable deflection exceeds design deflection

Bottom Chord1 - Span 4 design

Section details
Section type; CHS 42.4x2.6 (Tata Steel Celsius)
Steel grade - EN 10210-1:2006; S275H
Nominal thickness of element; tnom = t = 2.6 mm
Nominal yield strength; fy = 275 N/mm 2
Nominal ultimate tensile strength; fu = 410 N/mm 2
Modulus of elasticity; E = 210000 N/mm 2

Bottom Chord1 span 4 results summary Unit Capacity Maximum Utilisation Result
Shear resistance (y-y) kN 32.9 0.0 0.001 PASS
Bending resistance (y-y) kNm 1.1 0.0 0.019 PASS
Compression resistance kN 10.9 1.1 0.099 PASS
Tension resistance kN 89.4 0.6 0.007 PASS
Comb. bending and axial force 0.107 PASS
Deflection (y-y) mm 9.4 0.1 0.009 PASS

Lateral restraint
Section has lateral restraint at supports only

Consider Combination 1 - 1.35G + 1.5Q + 1.5RQ (Strength)

Classification of cross sections - Section 5.5
 = [235 N/mm 2 / f y] = 0.92

Tubular sections - Table 5.2 (sheet 3 of 3)

d / t = 16.3 = 19.1 *  2 <= 50 *  2 ; Class 1
Section is class 1
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 13
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Check tension - Section 6.2.3

Design tension force; N Ed = 0 kN
Design resistance of section - eq 6.6; N t,Rd = N pl,Rd = A * fy /  M0 = 89.4 kN
N Ed / N t,Rd = 0
PASS - Design tension resistance exceeds design tension

Check design 1815 mm along span

Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.005
PASS - Design bending resistance moment exceeds design bending moment
Check bending and axial force - Section 6.2.9
Normal force to plastic resistance force ratio; n = N Ed / N pl,Rd = 0.005
Reduced plastic moment resistance - Eq.6.39; M N,y,Rd = M pl,y,Rd * (1 - n 1.7 ) = 1.1 kNm
M y,Ed / M N,y,Rd = 0.005
PASS - Reduced bending resistance moment exceeds design bending moment

Check design at end of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.019
PASS - Design bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = -0.009 kNm / -0.022 kNm = 0.409
 y = 0.005 kNm / -0.022 kNm = -0.227
C my = max(0.1 - 0.8 *  y, 0.4) = 0.400
;  LT = -0.009 kNm / -0.022 kNm = 0.409
 LT = 0.005 kNm / -0.022 kNm = -0.227
C mLT = max(0.1 - 0.8 *  LT, 0.4) = 0.400

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.432
k zy = 0.6 * k yy = 0.259
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.107
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.386
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 14
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

PASS - Combined bending and compression checks are satisfied

Consider Combination 4 - 1.0G + 1.0Q + 0.5S + 0.5W (Service)

Check design 1758 mm along span

Check y-y axis deflection - Section 7.2.1
Maximum deflection;  y = 0.1 mm
Allowable deflection;  y,Allowable = L m1_s4 / 360 = 9.4 mm
 y /  y,Allowable = 0.009
PASS - Allowable deflection exceeds design deflection

Bottom Chord1 - Span 5 design

Section details
Section type; CHS 42.4x2.6 (Tata Steel Celsius)
Steel grade - EN 10210-1:2006; S275H
Nominal thickness of element; tnom = t = 2.6 mm
Nominal yield strength; fy = 275 N/mm 2
Nominal ultimate tensile strength; fu = 410 N/mm 2
Modulus of elasticity; E = 210000 N/mm 2

Bottom Chord1 span 5 results summary Unit Capacity Maximum Utilisation Result
Shear resistance (y-y) kN 32.9 0.1 0.002 PASS
Bending resistance (y-y) kNm 1.1 0.0 0.041 PASS
Compression resistance kN 64.5 1.1 0.017 PASS
Comb. bending and axial force 0.041 PASS
Deflection (y-y) mm 6.3 0.2 0.037 PASS

Lateral restraint
Section has lateral restraint at supports only

Consider Combination 3 - 1.35G + 1.5Q + 1.5 0 S + 1.5 0 W (Strength)

Classification of cross sections - Section 5.5

 = [235 N/mm 2 / f y] = 0.92

Tubular sections - Table 5.2 (sheet 3 of 3)

d / t = 16.3 = 19.1 *  2 <= 50 *  2 ; Class 1
Section is class 1
Check compression - Section 6.2.4
Design compression force; N Ed = 1.1 kN
Design resistance of section - eq 6.10; N c,Rd = N pl,Rd = A * f y /  M0 = 89.4 kN
N Ed / N c,Rd = 0.012
PASS - Design compression resistance exceeds design compression
Slenderness ratio for y-y axis flexural buckling - Section 6.3.1.3
Critical buckling length; L cr,y = L m1_s5 = 1125 mm
Critical buckling force; N cr,y =  2 * E * I y / L cr,y2 = 105.9 kN
Slenderness ratio for buckling - eq 6.50;  y = (A * f y / N cr,y) = 0.919
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 15
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Check y-y axis flexural buckling resistance - Section 6.3.1.1

Buckling curve - Table 6.2; a
Imperfection factor - Table 6.1;  y = 0.21
Buckling reduction determination factor; y = 0.5 * (1 +  y * ( y - 0.2) +  y2 ) = 0.998
Buckling reduction factor - eq 6.49;  y = min(1 / (y + (y2 -  y2 )), 1) = 0.721
Design buckling resistance - eq 6.47; N b,y,Rd =  y * A * fy /  M1 = 64.5 kN
N Ed / N b,y,Rd = 0.017
PASS - Design buckling resistance exceeds design compression
Slenderness ratio for z-z axis flexural buckling - Section 6.3.1.3
Critical buckling length; L cr,z = L m1_s5_seg1 = 1125 mm
Critical buckling force; N cr,z =  2 * E * I z / L cr,z 2 = 105.9 kN
Slenderness ratio for buckling - eq 6.50;  z = (A * f y / N cr,z ) = 0.919

Check z-z axis flexural buckling resistance - Section 6.3.1.1

Buckling curve - Table 6.2; a
Imperfection factor - Table 6.1;  z = 0.21
Buckling reduction determination factor; z = 0.5 * (1 +  z * ( z - 0.2) +  z 2) = 0.998
Buckling reduction factor - eq 6.49;  z = min(1 / (z + (z 2 -  z 2 )), 1) = 0.721
Design buckling resistance - eq 6.47; N b,z,Rd =  z * A * f y /  M1 = 64.5 kN
N Ed / N b,z,Rd = 0.017
PASS - Design buckling resistance exceeds design compression

Check design at start of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0.1 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.002
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.019
PASS - Design bending resistance moment exceeds design bending moment
Check bending and axial force - Section 6.2.9
Normal force to plastic resistance force ratio; n = N Ed / N pl,Rd = 0.012
Reduced plastic moment resistance - Eq.6.39; M N,y,Rd = M pl,y,Rd * (1 - n 1.7 ) = 1.1 kNm
M y,Ed / M N,y,Rd = 0.019
PASS - Reduced bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = -0.022 kNm / 0.046 kNm = -0.478
 y = 0.017 kNm / 0.046 kNm = 0.370
C my = max(0.2 + 0.8 *  y, 0.4) = 0.496
;  LT = -0.022 kNm / 0.046 kNm = -0.478
 LT = 0.017 kNm / 0.046 kNm = 0.370
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.496
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 16
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.502
k zy = 0.6 * k yy = 0.301
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.026
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.022
PASS - Combined bending and compression checks are satisfied

Check design at end of span

Check shear - Section 6.2.6
Design shear force; V y,Ed = 0 kN
Shear area - cl 6.2.6(3); A v = 2 * A /  = 207 mm 2
Design shear resistance - cl 6.2.6(2); V c,y,Rd = V pl,y,Rd = A v * (f y / (3)) /  M0 = 32.9 kN
V y,Ed / V c,y,Rd = 0.001
PASS - Design shear resistance exceeds design shear force
Check bending moment - Section 6.2.5
Design bending moment; M y,Ed = 0 kNm
Design bending resistance moment - eq 6.13; M c,y,Rd = M pl,y,Rd = W pl.y * f y /  M0 = 1.1 kNm
M y,Ed / M c,y,Rd = 0.041
PASS - Design bending resistance moment exceeds design bending moment
Check combined bending and compression - Section 6.3.3
Equivalent uniform moment factors - Table B.3;  y = -0.022 kNm / 0.046 kNm = -0.478
 y = 0.017 kNm / 0.046 kNm = 0.370
C my = max(0.2 + 0.8 *  y, 0.4) = 0.496
;  LT = -0.022 kNm / 0.046 kNm = -0.478
 LT = 0.017 kNm / 0.046 kNm = 0.370
C mLT = max(0.2 + 0.8 *  LT, 0.4) = 0.496

Interaction factors k ij for members not susceptible to torsional deformations - Table B.1
Characteristic moment resistance; M y,Rk = W pl.y * fy = 1.1 kNm
Characteristic moment resistance; M z,Rk = W pl.z * fy = 1.1 kNm
Characteristic resistance to normal force; N Rk = A * fy = 89.4 kN
Interaction factors; k yy = C my * (1 + min( y - 0.2, 0.8) * N Ed / ( y * N Rk /  M1 )) = 0.502
k zy = 0.6 * k yy = 0.301
;  LT = 1.000
Interaction formulae - eq 6.61 & eq 6.62; N Ed / ( y * N Rk /  M1 ) + k yy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.037
N Ed / ( z * N Rk /  M1 ) + k zy * M y,Ed / ( LT * M y,Rk /  M1 ) = 0.029
PASS - Combined bending and compression checks are satisfied
 Project Job no.
Julius Nyerere Hydropower Project - JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Typical Truss 17
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Consider Combination 2 - 1.0G + 1.0Q + 1.0RQ (Service)

Check design 789 mm along span

Check y-y axis deflection - Section 7.2.1
Maximum deflection;  y = 0.2 mm
Allowable deflection;  y,Allowable = L m1_s5 / 180 = 6.3 mm
 y /  y,Allowable = 0.037
PASS - Allowable deflection exceeds design deflection
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

RC STAIR DESIGN (EN 1992)

In accordance w ith EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 1.0.05

Design summary
Description Unit Provided Required Utilisation Result
Bottom long. reinf. -Mid Span mm 2 1923 1138 0.59 PASS
Top long. reinf. -Upper land. mm 2 1923 1138 0.59 PASS
Bottom long. reinf. -Lower land. mm 2 1923 569 0.30 PASS
Allowable Actual Utilisation Result
Span-to-depth ratio 52.00 27.31 0.53 PASS
Shear capacity -Upper supp. kN 225.01 120.06 0.53 PASS
Shear capacity -Lower supp. kN 225.01 80.04 0.36 PASS

20
8

0
7
200
300 6
5
4
150
1200 3
2
1

Flight

200

300 2100 2405

4805

Stair geometry
Number of risers; N steps = 8
Going; G = 300 mm
Rise; R = 150 mm
W aist; h waist = 200 mm
Breadth; b = 2450 mm
Length of the tread span; L mid = (N steps – 1)  G = 2100 mm
Overall height of stairs; h stairs = N steps  R = 1200 mm
Angle of stairs;  stairs = atan (R / G) = 26.57 

Upper landing - First interior support

Length of the upper landing; L up = 2405 mm
Depth of the upper landing; h up = 200 mm
W idth of the supporting element; w up = 230 mm
Distance to the centre of the support; d s,up = 115 mm
Lower landing - Simple end support
Length of the lower landing; L low = 300 mm
Depth of the lower landing; h low = 200 mm
W idth of the supporting element; w low = 120 mm
Distance to the centre of the support; d s,low = 60 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Effective span – 5.3.2.2

Overall length; L total = L low + L mid + L up = 4805 mm
Clear distance between the supports faces; L n = L total - w up -w low = 4455 mm
Effective span variable – cl.5.3.2.2(1); a up = min(0.5 * h up , 0.5 * w up ) = 100 mm
Effective span variable – cl.5.3.2.2(1); a low = min(0.5 * h low, 0.5 * w low) = 60 mm
Length of the effective span – exp.5.8; L span = L n + a low + a up = 4615 mm
Concrete details - Table 3.1.
Concrete strength class; C25/30
Characteristic compressive cylinder strength; fck = 25 N/mm 2
Mean value of compressive cylinder strength fcm =f ck + 8 N/mm 2 = 33.0 N/mm 2
Mean value of axial tensile strength fctm = 0.3 N/mm 2 * (fck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Secant modulus of elasticity of concrete E cm = 22 kN/mm 2 *(f cm /10 N/mm 2 )0.3 * AAF = 31475.8 N/mm 2
Partial factor for concrete – Table 2.1N;  C = 1.5
Density of concrete;  conc = 25.00 kN/m 3
Compression chord coefficient - cl.6.2.3(3);  cw = 1
Compressive strength coefficient – cl.3.1.6(1);  cc = 0.85
Design compr. concrete strength - exp.3.15 fcd =  cc * f ck /  C = 14.2 N/mm 2
Effective strength factor – exp.3.21;  = 1.00
Effect. compr. zone height factor – exp.3.19;  = 0.80
Ultimate strain - Table 3.1;  cu2 = 0.0035
Shortening strain - Table 3.1;  cu3 = 0.0035
k 1 = 0.40
k 2 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
k 3 = 0.40
k 4 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
Maximum aggregate size; h agg = 20 mm
Reinforcing steel details
Characteristic yield strength of reinforcement; fyk = 500 N/mm 2
Partial factor for reinforcing steel - Table 2.1N;  S = 1.15
Design yield strength of reinforcement; fyd = f yk /  S = 435 N/mm 2

Loading details
Self weight slab; g self,slab = h waist / cos( stairs )  (conc)  b = 13.7 kN/m
Self weight steps; g self,steps = R / 2  (conc)  b = 4.6 kN/m
Average self weight; g self,aver = g self,slab + g self,steps = 18.3 kN/m
Loading from finishes; g fin = 1.2 kN/m 2
Imposed variable load; q k = 4.0 kN/m 2
Permanent action factor;  G = 1.35
Imposed action factor;  Q = 1.50
Quasi-permanent value of variable action  2 = 0.30
Design load; F Ed =  G * (g self,aver + g fin * b) +  Q * q k * b = 43.4 kN /m
Quasi-permanent load; F QP = 1.0 * (g self,aver + g fin * b) +  2 * q k * b = 24.2 kN /m

Midspan design
 = 0.086
Design moment M = abs( * F Ed * L span 2 ) = 79.4 kNm
Nominal cover to reinforcement c nom = 25 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Diameter of bar for long. direction l =12 mm

Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.045
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1138 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 552 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19600 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 17
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1923 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 385 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 962 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 137 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 149 mm
Maximum stress permitted - Table 7.3N  s = 281 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 241522 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 883 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Quasi-permanent moment M QP = abs( * F QP * L span 2) = 44.3kNm

Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 143 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Deflection control - Section 7.4
Reference reinforcement ratio  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.00500
Required tension reinforcement ratio  = A s,req / (b  d mid ) = 0.00275
Required compression reinforcement ratio ' = A's,req / (b  d mid ) = 0.00000
Structural system factor - Table 7.4N K b = 1.30
Basic allow. span to depth ratio -exp.7.16(a)
std basic = K b * [11 + 1.5 * (fck / 1 N/mm 2) 0.5 *  0 /  +3.2 * (f ck / 1 N/mm 2 ) 0.5 * ( 0 /  - 1) 3/2 ] = 47.474
Reinforcement factor - exp.7.17 K s = min(A s,prov / A s,req  500 N/mm 2 / f yk, 1.5) = 1.500
Long span supp. brittle partition factor-cl.7.4.2(2) F1 = 1.00
Allowable span to depth ratio std allow = min(std basic * K s * F1, 40 * K b) = 52.000
Actual span to depth ratio std actual = L span / d mid = 27.308
PASS-Span to effective depth is less than the maximum allowable

Upper landing support

 = -0.086
Design moment M = abs( * F Ed * L span 2 ) = 79.4 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.045
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1138 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 552 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19600 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 17
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1923 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 385 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 962 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum bar spacing - Section 8.2

Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 137 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 149 mm
Maximum stress permitted - Table 7.3N  s = 281 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 241522 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 883 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 44.3kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 143 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.600
Design shear force; V =  * F Ed * L span = 120.1 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.29 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1923 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00464
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 204.9 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 225.0 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 225.0 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;

Lower landing support

Design moment at support M = 0.0 kNm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Nominal cover to reinforcement c nom = 25 mm

Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Calculated reinforcement at midspan cl. 9.3.1.2(1) A s,span = M mid / (f yd * z mid ) = 1138 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d,0.0013 * b * d, 0.5 * A s,span)
A s,min = 569 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19600 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 17
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1923 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 385 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 962 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 137 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Shear capacity check - Section 6.2
Shear coefficient;  = 0.400
Design shear force; V =  * F Ed * L span = 80.0 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.19 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1923 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00464
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3 / 2 * fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 204.9 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 225.0 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 225.0 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 01 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

SECTION A-A'

A
17 x 12 
10  @ 200
10  @ 200
17 x 12 

-U bars at lower support

A'

10  @ 200
17 x 12 

;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

RC STAIR DESIGN (EN 1992)

In accordance w ith EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 1.0.05

Design summary
Description Unit Provided Required Utilisation Result
Bottom long. reinf. -Mid Span mm 2 1810 1335 0.74 PASS
Top long. reinf. -Upper land. mm 2 1810 1335 0.74 PASS
Top long. reinf. -Lower land. mm 2 1923 1862 0.97 PASS
Allowable Actual Utilisation Result
Span-to-depth ratio 57.68 34.91 0.61 PASS
Shear capacity -Upper supp. kN 217.49 125.30 0.58 PASS
Shear capacity -Lower supp. kN 221.93 150.36 0.68 PASS

20
11

0
10
200
9
8
7
300 6
5
1650
4
150
3
2
1 Flight

200

300 3000 3000

6300

Stair geometry
Number of risers; N steps = 11
Going; G = 300 mm
Rise; R = 150 mm
W aist; h waist = 200 mm
Breadth; b = 2400 mm
Length of the tread span; L mid = (N steps – 1)  G = 3000 mm
Overall height of stairs; h stairs = N steps  R = 1650 mm
Angle of stairs;  stairs = atan (R / G) = 26.57 

Upper landing - Interior support

Length of the upper landing; L up = 3000 mm
Depth of the upper landing; h up = 200 mm
W idth of the supporting element; w up = 300 mm
Distance to the centre of the support; d s,up = 150 mm
Lower landing - First interior support
Length of the lower landing; L low = 300 mm
Depth of the lower landing; h low = 200 mm
W idth of the supporting element; w low = 300 mm
Distance to the centre of the support; d s,low = 150 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Effective span – 5.3.2.2

Overall length; L total = L low + L mid + L up = 6300 mm
Clear distance between the supports faces; L n = L total - w up -w low = 5700 mm
Effective span variable – cl.5.3.2.2(1); a up = min(0.5 * h up , 0.5 * w up ) = 100 mm
Effective span variable – cl.5.3.2.2(1); a low = min(0.5 * h low, 0.5 * w low) = 100 mm
Length of the effective span – exp.5.8; L span = L n + a low + a up = 5900 mm
Concrete details - Table 3.1.
Concrete strength class; C25/30
Characteristic compressive cylinder strength; fck = 25 N/mm 2
Mean value of compressive cylinder strength fcm =f ck + 8 N/mm 2 = 33.0 N/mm 2
Mean value of axial tensile strength fctm = 0.3 N/mm 2 * (fck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Secant modulus of elasticity of concrete E cm = 22 kN/mm 2 *(f cm /10 N/mm 2 )0.3 * AAF = 31475.8 N/mm 2
Partial factor for concrete – Table 2.1N;  C = 1.5
Density of concrete;  conc = 25.00 kN/m 3
Compression chord coefficient - cl.6.2.3(3);  cw = 1
Compressive strength coefficient – cl.3.1.6(1);  cc = 0.85
Design compr. concrete strength - exp.3.15 fcd =  cc * f ck /  C = 14.2 N/mm 2
Effective strength factor – exp.3.21;  = 1.00
Effect. compr. zone height factor – exp.3.19;  = 0.80
Ultimate strain - Table 3.1;  cu2 = 0.0035
Shortening strain - Table 3.1;  cu3 = 0.0035
k 1 = 0.40
k 2 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
k 3 = 0.40
k 4 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
Maximum aggregate size; h agg = 20 mm
Reinforcing steel details
Characteristic yield strength of reinforcement; fyk = 500 N/mm 2
Partial factor for reinforcing steel - Table 2.1N;  S = 1.15
Design yield strength of reinforcement; fyd = f yk /  S = 435 N/mm 2

Loading details
Self weight slab; g self,slab = h waist / cos( stairs )  (conc)  b = 13.4 kN/m
Self weight steps; g self,steps = R / 2  (conc)  b = 4.5 kN/m
Average self weight; g self,aver = g self,slab + g self,steps = 17.9 kN/m
Loading from finishes; g fin = 1.2 kN/m 2
Imposed variable load; q k = 4.0 kN/m 2
Permanent action factor;  G = 1.35
Imposed action factor;  Q = 1.50
Quasi-permanent value of variable action  2 = 0.30
Design load; F Ed =  G * (g self,aver + g fin * b) +  Q * q k * b = 42.5 kN /m
Quasi-permanent load; F QP = 1.0 * (g self,aver + g fin * b) +  2 * q k * b = 23.7 kN /m

Midspan design
 = 0.063
Design moment M = abs( * F Ed * L span 2 ) = 93.1 kNm
Nominal cover to reinforcement c nom = 25 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Diameter of bar for long. direction l =12 mm

Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.054
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 160 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1335 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 16
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1810 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 362 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 144 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 156 mm
Maximum stress permitted - Table 7.3N  s = 275 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236724 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 882 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Quasi-permanent moment M QP = abs( * F QP * L span 2) = 51.9kNm

Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 179 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 276.5 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Deflection control - Section 7.4
Reference reinforcement ratio  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.00500
Required tension reinforcement ratio  = A s,req / (b  d mid ) = 0.00329
Required compression reinforcement ratio ' = A's,req / (b  d mid ) = 0.00000
Structural system factor - Table 7.4N K b = 1.50
Basic allow. span to depth ratio -exp.7.16(a)
std basic = K b * [11 + 1.5 * (fck / 1 N/mm 2) 0.5 *  0 /  +3.2 * (f ck / 1 N/mm 2 ) 0.5 * ( 0 /  - 1) 3/2 ] = 42.559
Reinforcement factor - exp.7.17 K s = min(A s,prov / A s,req  500 N/mm 2 / f yk, 1.5) = 1.355
Long span supp. brittle partition factor-cl.7.4.2(2) F1 = 1.00
Allowable span to depth ratio std allow = min(std basic * K s * F1, 40 * K b) = 57.681
Actual span to depth ratio std actual = L span / d mid = 34.911
PASS-Span to effective depth is less than the maximum allowable

Upper landing support

 = -0.063
Design moment M = abs( * F Ed * L span 2 ) = 93.1 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.054
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 160 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1335 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 16
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1810 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 362 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum bar spacing - Section 8.2

Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 144 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 156 mm
Maximum stress permitted - Table 7.3N  s = 275 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236724 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 882 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 51.9kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 179 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 276.5 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.500
Design shear force; V =  * F Ed * L span = 125.3 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.31 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1810 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00446
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 200.8 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 217.5 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 217.5 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;

Lower landing support

 = -0.086
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Design moment M = abs( * F Ed * L span 2 ) = 127.2 kNm

Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.074
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 157 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1862 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 17
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1923 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 385 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 134 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 146 mm
Maximum stress permitted - Table 7.3N  s = 283 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236523 mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 02 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 857 mm 2

PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 70.9kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 235 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 206.7 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.600
Design shear force; V =  * F Ed * L span = 150.4 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.37 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1923 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00474
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 200.8 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 221.9 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 221.9 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;
SECTION A-A'

16 x 12 
10  @ 200
A

10  @ 200
17 x 12 

A'

10  @ 200
16 x 12 

;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

RC STAIR DESIGN (EN 1992)

In accordance w ith EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 1.0.05

Design summary
Description Unit Provided Required Utilisation Result
Bottom long. reinf. -Mid Span mm 2 1810 908 0.50 PASS
Top long. reinf. -Upper land. mm 2 1810 882(crk) 0.49 PASS
Top long. reinf. -Lower land. mm 2 1810 882(crk) 0.49 PASS
Allowable Actual Utilisation Result
Span-to-depth ratio 50.00 23.58 0.47 PASS
Shear capacity -Upper supp. kN 217.49 84.63 0.39 PASS
Shear capacity -Lower supp. kN 217.49 84.63 0.39 PASS

20
12

0
11
200
10
9
8
7
300 6
1800 5
4
150
3
2
Flight
1

200

300 3300 500

4100

Stair geometry
Number of risers; N steps = 12
Going; G = 300 mm
Rise; R = 150 mm
W aist; h waist = 200 mm
Breadth; b = 2400 mm
Length of the tread span; L mid = (N steps – 1)  G = 3300 mm
Overall height of stairs; h stairs = N steps  R = 1800 mm
Angle of stairs;  stairs = atan (R / G) = 26.57 

Upper landing - Monolithic end support

Length of the upper landing; L up = 500 mm
Depth of the upper landing; h up = 200 mm
W idth of the supporting element; w up = 115 mm
Distance to the centre of the support; d s,up = 58 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Lower landing - Monolithic end support

Length of the lower landing; L low = 300 mm
Depth of the lower landing; h low = 200 mm
W idth of the supporting element; w low = 115 mm
Distance to the centre of the support; d s,low = 58 mm
Effective span – 5.3.2.2
Overall length; L total = L low + L mid + L up = 4100 mm
Clear distance between the supports faces; L n = L total - w up -w low = 3870 mm
Effective span variable – cl.5.3.2.2(1); a up = min(0.5 * h up , 0.5 * w up ) = 58 mm
Effective span variable – cl.5.3.2.2(1); a low = min(0.5 * h low, 0.5 * w low) = 58 mm
Length of the effective span – exp.5.8; L span = L n + a low + a up = 3985 mm
Concrete details - Table 3.1.
Concrete strength class; C25/30
Characteristic compressive cylinder strength; fck = 25 N/mm 2
Mean value of compressive cylinder strength fcm =f ck + 8 N/mm 2 = 33.0 N/mm 2
Mean value of axial tensile strength fctm = 0.3 N/mm 2 * (fck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Secant modulus of elasticity of concrete E cm = 22 kN/mm 2 *(f cm /10 N/mm 2 )0.3 * AAF = 31475.8 N/mm 2
Partial factor for concrete – Table 2.1N;  C = 1.5
Density of concrete;  conc = 25.00 kN/m 3
Compression chord coefficient - cl.6.2.3(3);  cw = 1
Compressive strength coefficient – cl.3.1.6(1);  cc = 0.85
Design compr. concrete strength - exp.3.15 fcd =  cc * f ck /  C = 14.2 N/mm 2
Effective strength factor – exp.3.21;  = 1.00
Effect. compr. zone height factor – exp.3.19;  = 0.80
Ultimate strain - Table 3.1;  cu2 = 0.0035
Shortening strain - Table 3.1;  cu3 = 0.0035
k 1 = 0.40
k 2 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
k 3 = 0.40
k 4 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
Maximum aggregate size; h agg = 20 mm
Reinforcing steel details
Characteristic yield strength of reinforcement; fyk = 500 N/mm 2
Partial factor for reinforcing steel - Table 2.1N;  S = 1.15
Design yield strength of reinforcement; fyd = f yk /  S = 435 N/mm 2

Loading details
Self weight slab; g self,slab = h waist / cos( stairs )  (conc)  b = 13.4 kN/m
Self weight steps; g self,steps = R / 2  (conc)  b = 4.5 kN/m
Average self weight; g self,aver = g self,slab + g self,steps = 17.9 kN/m
Loading from finishes; g fin = 1.2 kN/m 2
Imposed variable load; q k = 4.0 kN/m 2
Permanent action factor;  G = 1.35
Imposed action factor;  Q = 1.50
Quasi-permanent value of variable action  2 = 0.30
Design load; F Ed =  G * (g self,aver + g fin * b) +  Q * q k * b = 42.5 kN /m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Quasi-permanent load; F QP = 1.0 * (g self,aver + g fin * b) +  2 * q k * b = 23.7 kN /m

Midspan design
 = 0.094
Design moment M = abs( * F Ed * L span 2 ) = 63.4 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.037
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 908 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 16
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1810 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 362 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 144 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 156 mm
Maximum stress permitted - Table 7.3N  s = 275 N/mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35

Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236724 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 882 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 35.3kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 122 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Deflection control - Section 7.4
Reference reinforcement ratio  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.00500
Required tension reinforcement ratio  = A s,req / (b  d mid ) = 0.00224
Required compression reinforcement ratio ' = A's,req / (b  d mid ) = 0.00000
Structural system factor - Table 7.4N K b = 1.25
Basic allow. span to depth ratio -exp.7.16(a)
std basic = K b * [11 + 1.5 * (fck / 1 N/mm 2) 0.5 *  0 /  +3.2 * (f ck / 1 N/mm 2 ) 0.5 * ( 0 /  - 1) 3/2 ] = 62.054
Reinforcement factor - exp.7.17 K s = min(A s,prov / A s,req  500 N/mm 2 / f yk, 1.5) = 1.500
Long span supp. brittle partition factor-cl.7.4.2(2) F1 = 1.00
Allowable span to depth ratio std allow = min(std basic * K s * F1, 40 * K b) = 50.000
Actual span to depth ratio std actual = L span / d mid = 23.580
PASS-Span to effective depth is less than the maximum allowable

Upper landing support

 = -0.043
Design moment M = abs( * F Ed * L span 2 ) = 29.0 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.017
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 416 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 16
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1810 mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

PASS - Tension reinforcement area is greater than area required

Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 362 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 144 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 156 mm
Maximum stress permitted - Table 7.3N  s = 275 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236724 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 882 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 16.2kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 72 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.500
Design shear force; V =  * F Ed * L span = 84.6 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.21 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1810 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00446
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3 / 2 * fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 200.8 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 217.5 kN
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 217.5 kN

PASS - Design force is less than maximum allowable- No shear reinforcement is required;

Lower landing support

 = -0.043
Design moment M = abs( * F Ed * L span 2 ) = 29.0 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.017
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 416 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 541 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 19200 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 16
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1810 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 362 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 942 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 144 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 156 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 01-Flight 03 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Maximum stress permitted - Table 7.3N  s = 275 N/mm 2

Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 236724 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 882 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 16.2kNm
Permanent load ratio R PL = M QP / M = 0.56
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 72 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.500
Design shear force; V =  * F Ed * L span = 84.6 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.21 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1810 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00446
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3 / 2 * fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 200.8 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 217.5 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 217.5 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;

SECTION A-A'

16 x 12 
10  @ 200

10  @ 200
16 x 12 

-U bars at lower support

A' -U bars at upper support

10  @ 200
16 x 12 

;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

RC STAIR DESIGN (EN 1992)

In accordance w ith EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 1.0.05

Design summary
Description Unit Provided Required Utilisation Result
Bottom long. reinf. -Mid Span mm 2 1357 1024 0.75 PASS
Top long. reinf. -Upper land. mm 2 1357 1024 0.75 PASS
Bottom long. reinf. -Lower land. mm 2 1357 512 0.38 PASS
Allowable Actual Utilisation Result
Span-to-depth ratio 45.46 32.07 0.71 PASS
Shear capacity -Upper supp. kN 159.48 91.66 0.57 PASS
Shear capacity -Lower supp. kN 159.48 61.10 0.38 PASS

20
14

0
13
200
12
11
10
9
8
7
2100 300 6
5
4
150
3
Flight
2
1

200

300 3900 1480

5680

Stair geometry
Number of risers; N steps = 14
Going; G = 300 mm
Rise; R = 150 mm
W aist; h waist = 200 mm
Breadth; b = 1740 mm
Length of the tread span; L mid = (N steps – 1)  G = 3900 mm
Overall height of stairs; h stairs = N steps  R = 2100 mm
Angle of stairs;  stairs = atan (R / G) = 26.57 

Upper landing - First interior support

Length of the upper landing; L up = 1480 mm
Depth of the upper landing; h up = 200 mm
W idth of the supporting element; w up = 230 mm
Distance to the centre of the support; d s,up = 115 mm
Lower landing - Simple end support
Length of the lower landing; L low = 300 mm
Depth of the lower landing; h low = 200 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

W idth of the supporting element; w low = 230 mm

Distance to the centre of the support; d s,low = 115 mm
Effective span – 5.3.2.2
Overall length; L total = L low + L mid + L up = 5680 mm
Clear distance between the supports faces; L n = L total - w up -w low = 5220 mm
Effective span variable – cl.5.3.2.2(1); a up = min(0.5 * h up , 0.5 * w up ) = 100 mm
Effective span variable – cl.5.3.2.2(1); a low = min(0.5 * h low, 0.5 * w low) = 100 mm
Length of the effective span – exp.5.8; L span = L n + a low + a up = 5420 mm
Concrete details - Table 3.1.
Concrete strength class; C25/30
Characteristic compressive cylinder strength; fck = 25 N/mm 2
Mean value of compressive cylinder strength fcm =f ck + 8 N/mm 2 = 33.0 N/mm 2
Mean value of axial tensile strength fctm = 0.3 N/mm 2 * (fck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Secant modulus of elasticity of concrete E cm = 22 kN/mm 2 *(f cm /10 N/mm 2 )0.3 * AAF = 31475.8 N/mm 2
Partial factor for concrete – Table 2.1N;  C = 1.5
Density of concrete;  conc = 25.00 kN/m 3
Compression chord coefficient - cl.6.2.3(3);  cw = 1
Compressive strength coefficient – cl.3.1.6(1);  cc = 0.85
Design compr. concrete strength - exp.3.15 fcd =  cc * f ck /  C = 14.2 N/mm 2
Effective strength factor – exp.3.21;  = 1.00
Effect. compr. zone height factor – exp.3.19;  = 0.80
Ultimate strain - Table 3.1;  cu2 = 0.0035
Shortening strain - Table 3.1;  cu3 = 0.0035
k 1 = 0.40
k 2 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
k 3 = 0.40
k 4 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
Maximum aggregate size; h agg = 20 mm
Reinforcing steel details
Characteristic yield strength of reinforcement; fyk = 500 N/mm 2
Partial factor for reinforcing steel - Table 2.1N;  S = 1.15
Design yield strength of reinforcement; fyd = f yk /  S = 435 N/mm 2

Loading details
Self weight slab; g self,slab = h waist / cos( stairs )  (conc)  b = 9.7 kN/m
Self weight steps; g self,steps = R / 2  (conc)  b = 3.3 kN/m
Average self weight; g self,aver = g self,slab + g self,steps = 13.0 kN/m
Loading from finishes; g fin = 1.2 kN/m 2
Imposed variable load; q k = 3.0 kN/m 2
Permanent action factor;  G = 1.35
Imposed action factor;  Q = 1.50
Quasi-permanent value of variable action  2 = 0.30
Design load; F Ed =  G * (g self,aver + g fin * b) +  Q * q k * b = 28.2 kN /m
Quasi-permanent load; F QP = 1.0 * (g self,aver + g fin * b) +  2 * q k * b = 16.6 kN /m

Midspan design
 = 0.086
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Design moment M = abs( * F Ed * L span 2 ) = 71.2 kNm

Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.057
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 160 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1024 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 392 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 13920 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 683 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 141 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 153 mm
Maximum stress permitted - Table 7.3N  s = 278 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 171544 mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 633 mm 2

PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 42.0kNm
Permanent load ratio R PL = M QP / M = 0.59
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 194 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 257.9 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Deflection control - Section 7.4
Reference reinforcement ratio  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.00500
Required tension reinforcement ratio  = A s,req / (b  d mid ) = 0.00348
Required compression reinforcement ratio ' = A's,req / (b  d mid ) = 0.00000
Structural system factor - Table 7.4N K b = 1.30
Basic allow. span to depth ratio -exp.7.16(a)
std basic = K b * [11 + 1.5 * (fck / 1 N/mm 2) 0.5 *  0 /  +3.2 * (f ck / 1 N/mm 2 ) 0.5 * ( 0 /  - 1) 3/2 ] = 34.295
Reinforcement factor - exp.7.17 K s = min(A s,prov / A s,req  500 N/mm 2 / f yk, 1.5) = 1.326
Long span supp. brittle partition factor-cl.7.4.2(2) F1 = 1.00
Allowable span to depth ratio std allow = min(std basic * K s * F1, 40 * K b) = 45.465
Actual span to depth ratio std actual = L span / d mid = 32.071
PASS-Span to effective depth is less than the maximum allowable

Upper landing support

 = -0.086
Design moment M = abs( * F Ed * L span 2 ) = 71.2 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.057
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 160 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 1024 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 392 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 13920 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 683 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum bar spacing - Section 8.2

Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 141 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 153 mm
Maximum stress permitted - Table 7.3N  s = 278 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 99 mm
Area of concrete in the tensile zone A ct = b * y = 171544 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 633 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 42.0kNm
Permanent load ratio R PL = M QP / M = 0.59
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 194 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 257.9 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.600
Design shear force; V =  * F Ed * L span = 91.7 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.31 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1357 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00462
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 145.6 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 159.5 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 159.5 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;

Lower landing support

Design moment at support M = 0.0 kNm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Nominal cover to reinforcement c nom = 25 mm

Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Calculated reinforcement at midspan cl. 9.3.1.2(1) A s,span = M mid / (f yd * z mid ) = 1024 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d,0.0013 * b * d, 0.5 * A s,span)
A s,min = 512 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 13920 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 683 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 141 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Shear capacity check - Section 6.2
Shear coefficient;  = 0.400
Design shear force; V =  * F Ed * L span = 61.1 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.21 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1357 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00462
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3 / 2 * fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 145.6 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 159.5 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 159.5 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 01 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

SECTION A-A'

12 x 12 
10  @ 200

10  @ 200

12 x 12 

-U bars at lower support

A'

10  @ 200
12 x 12 

;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

RC STAIR DESIGN (EN 1992)

In accordance w ith EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 1.0.05

Design summary
Description Unit Provided Required Utilisation Result
Bottom long. reinf. -Mid Span mm 2 1357 738 0.54 PASS
Top long. reinf. -Upper land. mm 2 1357 409(crk) 0.30 PASS
Top long. reinf. -Lower land. mm 2 1357 854 0.63 PASS
Allowable Actual Utilisation Result
Span-to-depth ratio 56.00 34.14 0.61 PASS
Shear capacity -Upper supp. kN 129.28 54.60 0.42 PASS
Shear capacity -Lower supp. kN 129.28 71.22 0.55 PASS

20
14

0
13
200
12
11
10
9
8
7
2100 300 6
5
4
150
3
Flight
2
1

200

1500 3900 630

6030

Stair geometry
Number of risers; N steps = 14
Going; G = 300 mm
Rise; R = 150 mm
W aist; h waist = 200 mm
Breadth; b = 1270 mm
Length of the tread span; L mid = (N steps – 1)  G = 3900 mm
Overall height of stairs; h stairs = N steps  R = 2100 mm
Angle of stairs;  stairs = atan (R / G) = 26.57 

Upper landing - Monolithic end support

Length of the upper landing; L up = 630 mm
Depth of the upper landing; h up = 200 mm
W idth of the supporting element; w up = 230 mm
Distance to the centre of the support; d s,up = 115 mm
Lower landing - First interior support
Length of the lower landing; L low = 1500 mm
Depth of the lower landing; h low = 200 mm
W idth of the supporting element; w low = 230 mm
Distance to the centre of the support; d s,low = 115 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Effective span – 5.3.2.2

Overall length; L total = L low + L mid + L up = 6030 mm
Clear distance between the supports faces; L n = L total - w up -w low = 5570 mm
Effective span variable – cl.5.3.2.2(1); a up = min(0.5 * h up , 0.5 * w up ) = 100 mm
Effective span variable – cl.5.3.2.2(1); a low = min(0.5 * h low, 0.5 * w low) = 100 mm
Length of the effective span – exp.5.8; L span = L n + a low + a up = 5770 mm
Concrete details - Table 3.1.
Concrete strength class; C25/30
Characteristic compressive cylinder strength; fck = 25 N/mm 2
Mean value of compressive cylinder strength fcm =f ck + 8 N/mm 2 = 33.0 N/mm 2
Mean value of axial tensile strength fctm = 0.3 N/mm 2 * (fck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Secant modulus of elasticity of concrete E cm = 22 kN/mm 2 *(f cm /10 N/mm 2 )0.3 * AAF = 31475.8 N/mm 2
Partial factor for concrete – Table 2.1N;  C = 1.5
Density of concrete;  conc = 25.00 kN/m 3
Compression chord coefficient - cl.6.2.3(3);  cw = 1
Compressive strength coefficient – cl.3.1.6(1);  cc = 0.85
Design compr. concrete strength - exp.3.15 fcd =  cc * f ck /  C = 14.2 N/mm 2
Effective strength factor – exp.3.21;  = 1.00
Effect. compr. zone height factor – exp.3.19;  = 0.80
Ultimate strain - Table 3.1;  cu2 = 0.0035
Shortening strain - Table 3.1;  cu3 = 0.0035
k 1 = 0.40
k 2 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
k 3 = 0.40
k 4 = 1.0 * (0.6 + 0.0014 /  cu2) = 1.00
Maximum aggregate size; h agg = 20 mm
Reinforcing steel details
Characteristic yield strength of reinforcement; fyk = 500 N/mm 2
Partial factor for reinforcing steel - Table 2.1N;  S = 1.15
Design yield strength of reinforcement; fyd = f yk /  S = 435 N/mm 2

Loading details
Self weight slab; g self,slab = h waist / cos( stairs )  (conc)  b = 7.1 kN/m
Self weight steps; g self,steps = R / 2  (conc)  b = 2.4 kN/m
Average self weight; g self,aver = g self,slab + g self,steps = 9.5 kN/m
Loading from finishes; g fin = 1.2 kN/m 2
Imposed variable load; q k = 3.0 kN/m 2
Permanent action factor;  G = 1.35
Imposed action factor;  Q = 1.50
Quasi-permanent value of variable action  2 = 0.30
Design load; F Ed =  G * (g self,aver + g fin * b) +  Q * q k * b = 20.6 kN /m
Quasi-permanent load; F QP = 1.0 * (g self,aver + g fin * b) +  2 * q k * b = 12.1 kN /m

Midspan design
 = 0.075
Design moment M = abs( * F Ed * L span 2 ) = 51.4 kNm
Nominal cover to reinforcement c nom = 25 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Diameter of bar for long. direction l =12 mm

Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.057
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 160 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 738 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 286 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 10160 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 499 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 98 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 110 mm
Maximum stress permitted - Table 7.3N  s = 312 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 98 mm
Area of concrete in the tensile zone A ct = b * y = 124563 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 409 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Quasi-permanent moment M QP = abs( * F QP * L span 2) = 30.3kNm

Permanent load ratio R PL = M QP / M = 0.59
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 140 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Deflection control - Section 7.4
Reference reinforcement ratio  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.00500
Required tension reinforcement ratio  = A s,req / (b  d mid ) = 0.00344
Required compression reinforcement ratio ' = A's,req / (b  d mid ) = 0.00000
Structural system factor - Table 7.4N K b = 1.40
Basic allow. span to depth ratio -exp.7.16(a)
std basic = K b * [11 + 1.5 * (fck / 1 N/mm 2) 0.5 *  0 /  +3.2 * (f ck / 1 N/mm 2 ) 0.5 * ( 0 /  - 1) 3/2 ] = 37.523
Reinforcement factor - exp.7.17 K s = min(A s,prov / A s,req  500 N/mm 2 / f yk, 1.5) = 1.500
Long span supp. brittle partition factor-cl.7.4.2(2) F1 = 1.00
Allowable span to depth ratio std allow = min(std basic * K s * F1, 40 * K b) = 56.000
Actual span to depth ratio std actual = L span / d mid = 34.142
PASS-Span to effective depth is less than the maximum allowable

Upper landing support

 = -0.040
Design moment M = abs( * F Ed * L span 2 ) = 27.4 kNm
Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.030
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 161 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 392 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 286 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 10160 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 499 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum bar spacing - Section 8.2

Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 98 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 110 mm
Maximum stress permitted - Table 7.3N  s = 312 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 98 mm
Area of concrete in the tensile zone A ct = b * y = 124563 mm 2
Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 409 mm 2
PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 16.2kNm
Permanent load ratio R PL = M QP / M = 0.59
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 74 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.460
Design shear force; V =  * F Ed * L span = 54.6 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.25 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1357 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00632
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 106.2 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 129.3 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 129.3 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;

Lower landing support

 = -0.086
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Design moment M = abs( * F Ed * L span 2 ) = 58.9 kNm

Nominal cover to reinforcement c nom = 25 mm
Diameter of bar for long. direction l =12 mm
Depth of reinforcement d = h - c nom - l / 2 = 169 mm
Redistribution ratio (20% assumed)  = 0.80
K coefficient K = M / (b * d 2 * f ck ) = 0.065
K' coefficient K' = (2 *  *  cc /  C ) * (1 -  * ( - k 1) / (2 * k 2 )) * ( * ( - k 1 ) / (2 *
k 2 )) = 0.152
K < K' -Compression reinforcement is not required
Lever arm z = min(0.5 * d * (1 + (1 - 2 * K z / ( *  cc /  C )) 0.5 ), 0.95 * d)
z = 159 mm
Tension area required in longitudinal direction A s,req = M / (fyd * z) = 854 mm 2
Minimum area of reinforcement – exp.9.1.N A s,min = max(0.26 * fctm / f yk * b * d, 0.0013 * b * d)= 286 mm 2
Maximum area of reinforcement - cl.9.2.1.1(3) A s,max = 0.04 * b * h = 10160 mm 2
Tension reinforcement check
Diameter of bars for longitudinal direction l = 12 mm
Number of bars in longitudinal direction N = 12
Diameter of bars for transverse direction t = 10 mm
Bar spacing in transverse direction s = 200 mm
Tension area provided in longitudinal direction A s,prov = N *  * l2 /4 = 1357 mm 2
PASS - Tension reinforcement area is greater than area required
Tension secondary area required in transverse direction – cl.9.3.1.1(2)
A s,req,t = 0.2 * max(A s,prov , A s,req ) = 271 mm 2
Tension area provided in transverse direction A s,prov,t =  * t2 /4 * (b / s) = 499 mm 2
PASS - Tension reinforcement in transverse direction is greater than area required
Minimum bar spacing - Section 8.2
Bar spacing (clear distance) in long. direction; s bar,l = (b - (2 * c nom + N * l)) / (N - 1) = 98 mm
k spc1 = 1
k spc2 = 5 mm
Minimum allowable bar spacing – cl.8.2(2); s min,l = max(k spc1 * l, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Bar spacing (clear distance) in transv. direction; s bar,t = s - t = 190 mm
Minimum allowable bar spacing – cl.8.2(2); s min,t = max(k spc1 * t, h agg + k spc2 , 20 mm) = 25 mm
PASS - Actual bar spacing exceeds minimum allowable
Crack control - Section 7.3
Maximum crack width w k = 0.3 mm
Design value modulus of elasticity reinf – 3.2.7(4) E s = 200000 N/mm 2
Mean value of concrete tensile strength fct,eff = fctm = 2.6 N/mm 2
Stress distribution coefficient k c = 0.4
Non-uniform self-equilibrating stress coefficient k =min(max(1 + (300 mm - min(h, b)) * 0.35 / 500 mm, 0.65), 1) = 1.00
Actual tension bar spacing s bar = (b -(2 * (c nom +  / 2))) / (N - 1) = 110 mm
Maximum stress permitted - Table 7.3N  s = 312 N/mm 2
Steel to concrete modulus of elast. ratio  cr = E s / E cm = 6.35
Distance of the Elastic NA from tension face y = (b * h 2 / 2 + A s,prov * ( cr - 1) * (h - d)) / (b * h + A s,prov * ( cr - 1))
y = 98 mm
Area of concrete in the tensile zone A ct = b * y = 124563 mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Staircase Type 02-Flight 02 7
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum area of reinforcement required - exp.7.1 A sc,min = k c * k * f ct,eff * A ct /  s = 409 mm 2

PASS - Area of tension reinforcement provided exceeds minimum required for crack control
Quasi-permanent moment M QP = abs( * F QP * L span 2) = 34.8kNm
Permanent load ratio R PL = M QP / M = 0.59
Service stress in reinforcement  sr = fyd * A s,req / A s,prov * R PL = 162 N/mm 2
Maximum bar spacing - Tables 7.3N s bar,max = 298.1 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Shear capacity check - Section 6.2
Shear coefficient;  = 0.600
Design shear force; V =  * F Ed * L span = 71.2 kN
Effective depth; d = 169 mm
Shear stress; v = V / (b * d) = 0.33 N/mm 2
Design shear resist. coefficient. – cl.6.2.2(1) C Rd,c = 0.18 /  C = 0.120
Tension reinforcement provided; A sl = N *  * l2 /4= 1357 mm 2
Design shear resist. size factor. – cl.6.2.2(1) K sh = min(1 + (200 mm / d) 1/2 , 2) = 2.00
Design shear resist. factor. – cl.6.2.2(1)  1 = A sl / (b * d) = 0.00632
Design shear resist. factor. – exp.6.3.N v min = (0.035 (N) 1/2 / mm) * K sh 3/2
* fck 1/2 = 0.49 N/mm 2
Minimum design shear resistance – exp.6.2(b) V Rd,cmin = (v min ) * b * d = 106.2 kN
Design shear resist. without reinf. – exp.6.2(a) V Rd,c1 = (C Rd,c * K sh * (100 N 2 / mm 4 *  1 * f ck ) 1/3 )* b * d
V Rd,c1 = 129.3 kN
V Rd,c = max(V Rd,c1 , V Rd,cmin ) = 129.3 kN
PASS - Design force is less than maximum allowable- No shear reinforcement is required;
SECTION A-A'

12 x 12 
10  @ 200

10  @ 200
12 x 12 

A' -U bars at upper support

10  @ 200
12 x 12 

;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 1
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

CRITICAL CORNER PANEL

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.18

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 342 0.605 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 457 0.808 PASS
Bar spacing at support mm 200 283 0.706 PASS
Shear at cont. supp kN/m 73.9 49.3 0.667 PASS
Shear at discont. supp kN/m 73.9 44.3 0.599 PASS
Deflection ratio 37.50 51.10 0.734 PASS
Long span
Reinf. at midspan mm 2 /m 565 298 0.528 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 395 0.698 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 69.8 47.9 0.686 PASS
Shear at discont. supp kN/m 69.8 44.3 0.635 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

5400

6000

Slab definition
Slab reference name; Critical Corner Panel
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 175 mm
Shorter effective span of panel; lx = 5400 mm
Longer effective span of panel; ly = 6000 mm
Support conditions; Tw o adjacent edges discontinuous
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
Loading
Characteristic permanent action; G k = 6.6 kN/m 2
Characteristic variable action; Q k = 5.0 kN/m 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 2
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Partial factor for permanent action;  G = 1.35

Partial factor for variable action;  Q = 1.50
Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 16.4 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 8.1 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2  (f ck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0426
Design bending moment; M x_p =  sx_p  q  l x2 = 20.4 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 144.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.039
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53  K))) = 136.8 mm
Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 342 mm 2 /m
Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 192 mm 2/m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 3
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 342 mm 2 /m

PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 129.9 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0340
Design bending moment; M y_p =  sy_p  q  l x2 = 16.3 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 132.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.037
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 298 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 176 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 298 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 113.2 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0568
Design bending moment; M x_n =  sx_n  q  l x2 = 27.2 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 144.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.052
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53  K))) = 136.8 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 457 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 192 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 457 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 173.4 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_n = 283 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 4
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Actual bar spacing; s x_n = 200 mm

PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0450
Design bending moment; M y_n =  sy_n  q  l x2 = 21.5 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 132.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.049
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 395 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 176 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 395 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 149.9 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = q  l x / 2 + M x_n / lx = 49.3 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0039
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 71.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 73.9 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = q  l x / 2 + M y_n / l y = 47.9 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0043
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 65.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 69.8 kN/m
PASS - Shear capacity is adequate
Shear capacity check at short span discontinuous support
Shear force; V x_d = q  l x / 2 = ;44.3; kN/m;
Reinforcement provided; 12 mm dia. bars at 200 mm centres
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 5
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Area provided; A sx_d = 565 mm 2 /m

Effective depth; d x_d = h - c nom_b - x_d / 2 = ;144.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d x_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_d / (b  d x_d )) = 0.0039
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5 b  d x_d
V Rd,c_min = 71.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_x_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d x_d) = 73.9 kN/m
PASS - Shear capacity is adequate (0.599)
Shear capacity check at long span discontinuous support
Shear force; V y_d = q  l x / 2 = ;44.3; kN/m;
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_d = 565 mm 2 /m
Effective depth; d y_d = h - c nom_b - x_p - y_d / 2 = ;132.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d y_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_d / (b  d y_d )) = 0.0043
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d y_d
V Rd,c_min = 65.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_y_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d y_d ) = 69.8 kN/m
PASS - Shear capacity is adequate (0.635)
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000
Stuctural system factor (Table 7.4N); K  = 1.3
Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K   [11 +1.5(fck /1 N/mm 2 )0.5  0 / + 3.2(f ck /1 N/mm 2 )0.5( 0 / -1) 1.5 ] = 34.06
Mod span-to-depth ratio limit;
ratio lim_x = min(40  K , min(1.5, (500 N/mm 2 / f yk )  (A sx_p / A sx_p_m ))  ratio lim_x_bas ) = 51.10
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 37.50
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2
Discontinuous support in short span direction; 12 mm dia. bars at 200 mm centres B1
Discontinuous support in long span direction; 12 mm dia. bars at 200 mm centres B2

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 6
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs B2

12mm bars @ 200 ctrs B2

 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 1
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

CRITICAL EDGE PANEL

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.18

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 349 0.617 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 474 0.837 PASS
Bar spacing at support mm 200 258 0.775 PASS
Shear at cont. supp kN/m 73.9 57.6 0.779 PASS
Shear at discont. supp kN/m 73.9 41.9 0.567 PASS
Deflection ratio 37.50 51.10 0.734 PASS
Long span
Reinf. at midspan mm 2 /m 565 290 0.514 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 384 0.679 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 69.8 57.6 0.825 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

5400

6000

Slab definition
Slab reference name; Critical edge Panel
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 175 mm
Shorter effective span of panel; lx = 5400 mm
Longer effective span of panel; ly = 6000 mm
Support conditions; One long edge discontinuous
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
Loading
Characteristic permanent action; G k = 8.8 kN/m 2
Characteristic variable action; Q k = 5.0 kN/m 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 2
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Partial factor for permanent action;  G = 1.35

Partial factor for variable action;  Q = 1.50
Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 19.4 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 10.3 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2  (f ck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0367
Design bending moment; M x_p =  sx_p  q  l x2 = 20.7 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 144.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.040
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53  K))) = 136.8 mm
Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 349 mm 2 /m
Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 192 mm 2/m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 3
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 349 mm 2 /m

PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 142.5 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0280
Design bending moment; M y_p =  sy_p  q  l x2 = 15.8 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 132.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.036
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 290 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 176 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 290 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 118.7 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0498
Design bending moment; M x_n =  sx_n  q  l x2 = 28.2 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 144.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.054
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53  K))) = 136.7 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 474 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 192 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 474 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 193.5 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_n = 258 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 4
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Actual bar spacing; s x_n = 200 mm

PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0370
Design bending moment; M y_n =  sy_n  q  l x2 = 20.9 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 132.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.048
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 384 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 176 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 384 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 156.9 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = 1.1  q  lx / 2 = 57.6 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0039
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 71.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 73.9 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = 1.1  q  lx / 2 = 57.6 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0043
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 65.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 69.8 kN/m
PASS - Shear capacity is adequate
Shear capacity check at short span discontinuous support
Shear force; V x_d = 0.8  q  lx / 2 = ;41.9; kN/m;
Reinforcement provided; 12 mm dia. bars at 200 mm centres
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 5
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Area provided; A sx_d = 565 mm 2 /m

Effective depth; d x_d = h - c nom_b - x_d / 2 = ;144.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d x_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_d / (b  d x_d )) = 0.0039
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5 b  d x_d
V Rd,c_min = 71.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_x_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d x_d) = 73.9 kN/m
PASS - Shear capacity is adequate (0.567)
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000
Stuctural system factor (Table 7.4N); K  = 1.3
Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K   [11 +1.5(fck /1 N/mm 2 )0.5  0 / + 3.2(f ck /1 N/mm 2 )0.5( 0 / -1) 1.5 ] = 34.06
Mod span-to-depth ratio limit;
ratio lim_x = min(40  K , min(1.5, (500 N/mm 2 / f yk )  (A sx_p / A sx_p_m ))  ratio lim_x_bas ) = 51.10
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 37.50
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2
Discontinuous support in short span direction; 12 mm dia. bars at 200 mm centres B1

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 6
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs B2

12mm bars @ 200 ctrs T2

 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 1
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

CRITICAL INTERIOR PANEL

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.18

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 276 0.488 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 364 0.644 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 73.9 53.4 0.722 PASS
Deflection ratio 37.50 58.96 0.636 PASS
Long span
Reinf. at midspan mm 2 /m 565 254 0.449 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 339 0.599 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 69.8 53.4 0.766 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

5400

6000

Slab definition
Slab reference name; Critical Interior Panel
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 175 mm
Shorter effective span of panel; lx = 5400 mm
Longer effective span of panel; ly = 6000 mm
Support conditions; Four edges continuous (interior panel)
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
Loading
Characteristic permanent action; G k = 9.1 kN/m 2
Characteristic variable action; Q k = 5.0 kN/m 2
Partial factor for permanent action;  G = 1.35
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 2
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Partial factor for variable action;  Q = 1.50

Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 19.8 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 10.6 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2  (f ck / 1 N/mm 2 ) 2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0284
Design bending moment; M x_p =  sx_p  q  l x2 = 16.4 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 144.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.032
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53  K))) = 136.8 mm
Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 276 mm 2 /m
Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 192 mm 2/m
Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 276 mm 2 /m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 3
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

PASS - Area of reinforcement provided exceeds area required

Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 113.7 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0240
Design bending moment; M y_p =  sy_p  q  l x2 = 13.8 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 132.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.032
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 254 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 176 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 254 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 104.6 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0376
Design bending moment; M x_n =  sx_n  q  l x2 = 21.7 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 144.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.042
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53  K))) = 136.8 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 364 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 192 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 364 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 150.1 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_n = 300 mm
Actual bar spacing; s x_n = 200 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 4
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

PASS - The reinforcement spacing is acceptable

Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0320
Design bending moment; M y_n =  sy_n  q  l x2 = 18.5 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 132.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.042
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598   - 0.18   2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53  K))) = 125.4 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 339 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 176 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 339 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 139.5 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = q  l x / 2 = 53.4 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0039
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 71.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 73.9 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = q  l x / 2 = 53.4 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0043
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2  k 1.5  (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 65.3 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 69.8 kN/m
PASS - Shear capacity is adequate
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited
Calcs for Start page no./Revision
Plot No. 305B,
Administration Building Slab Design 5
Rweyabura Street, Mikocheni
P O Box 12965, Dar Es Salaam , Tanzania. Calcs by Calcs date Checked by Checked date Approved by Approved date
GL 11/23/2020 H, Josia 11/23/2020 11/23/2020

Stuctural system factor (Table 7.4N); K  = 1.5

Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K   [11 +1.5(fck /1 N/mm 2 )0.5  0 / + 3.2(f ck /1 N/mm 2 )0.5( 0 / -1) 1.5 ] = 39.31
Mod span-to-depth ratio limit;
ratio lim_x = min(40  K , min(1.5, (500 N/mm 2 / f yk )  (A sx_p / A sx_p_m ))  ratio lim_x_bas ) = 58.96
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 37.50
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs B2
12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs T2

 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

CRITICAL CORNER PANEL GUEST ROOMS

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.20

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 185 0.328 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 242 0.428 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 65.1 35.5 0.545 PASS
Shear at discont. supp kN/m 65.1 32.4 0.498 PASS
Deflection ratio 32.77 51.10 0.641 PASS
Long span
Reinf. at midspan mm 2 /m 565 195 0.344 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 258 0.456 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 60.7 35.4 0.583 PASS
Shear at discont. supp kN/m 60.7 32.4 0.535 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

3900

3900

Slab definition
Slab reference name; Critical Corner Panel Guest Rooms
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 150 mm
Shorter effective span of panel; lx = 3900 mm
Longer effective span of panel; ly = 3900 mm
Support conditions; Tw o adjacent edges discontinuous
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Loading
Characteristic permanent action; G k = 10.1 kN/m 2
Characteristic variable action; Q k = 2.0 kN/m 2
Partial factor for permanent action;  G = 1.35
Partial factor for variable action;  Q = 1.50
Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 16.6 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 10.7 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2 * (fck / 1 N/mm 2 )2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0360
Design bending moment; M x_p =  sx_p  q  l x2 = 9.1 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 119.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.026
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53 * K))) = 113.0 mm

Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 185 mm 2 /m
Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 159 mm 2/m
Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 185 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 91.6 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0340
Design bending moment; M y_p =  sy_p  q  l x2 = 8.6 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 107.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.030
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 195 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 143 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 195 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 96.3 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0470
Design bending moment; M x_n =  sx_n  q  l x2 = 11.9 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 119.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.034
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53 * K))) = 113.0 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 242 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 159 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 242 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Check reinforcement spacing

Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 119.7 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_n = 300 mm
Actual bar spacing; s x_n = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0450
Design bending moment; M y_n =  sy_n  q  l x2 = 11.4 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 107.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.040
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 258 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 143 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 258 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 127.4 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = q * l x / 2 + M x_n / l x = 35.5 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0048
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 58.9 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 65.1 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = q * l x / 2 + M y_n / l y = 35.4 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0053
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 53.0 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 60.7 kN/m
PASS - Shear capacity is adequate
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Shear capacity check at short span discontinuous support

Shear force; V x_d = q * l x / 2 = ;32.4; kN/m;
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_d = 565 mm 2 /m
Effective depth; d x_d = h - c nom_b - x_d / 2 = ;119.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d x_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_d / (b  d x_d )) = 0.0048
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d x_d
V Rd,c_min = 58.9 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_x_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d x_d) = 65.1 kN/m
PASS - Shear capacity is adequate (0.498)
Shear capacity check at long span discontinuous support
Shear force; V y_d = q * l x / 2 = ;32.4; kN/m;
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_d = 565 mm 2 /m
Effective depth; d y_d = h - c nom_b - x_p - y_d / 2 = ;107.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d y_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_d / (b  d y_d )) = 0.0053
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d y_d
V Rd,c_min = 53.0 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_y_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d y_d ) = 60.7 kN/m
PASS - Shear capacity is adequate (0.535)
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000
Stuctural system factor (Table 7.4N); K  = 1.3
Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K  * [11 +1.5*(f ck /1 N/mm 2 )0.5 * 0 / + 3.2*(f ck/1 N/mm 2 ) 0.5 *( 0 / -1) 1.5 ] = 34.06
Mod span-to-depth ratio limit;
ratio lim_x = min(40 * K , min(1.5, (500 N/mm 2 / fyk ) * (A sx_p / A sx_p_m )) * ratio lim_x_bas ) = 51.10
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 32.77
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2
Discontinuous support in short span direction; 12 mm dia. bars at 200 mm centres B1
Discontinuous support in long span direction; 12 mm dia. bars at 200 mm centres B2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs B2

12mm bars @ 200 ctrs B2

 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

CRITICAL INTERNAL PANEL GUEST ROOMS

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.20

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 159 0.281 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 160 0.282 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 65.1 32.4 0.498 PASS
Deflection ratio 32.77 58.96 0.556 PASS
Long span
Reinf. at midspan mm 2 /m 565 143 0.252 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 183 0.324 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 60.7 32.4 0.535 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

3900

3900

Slab definition
Slab reference name; Critical Internal Panel Guest Rooms
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 150 mm
Shorter effective span of panel; lx = 3900 mm
Longer effective span of panel; ly = 3900 mm
Support conditions; Four edges continuous (interior panel)
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
Loading
Characteristic permanent action; G k = 10.1 kN/m 2
Characteristic variable action; Q k = 2.0 kN/m 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Partial factor for permanent action;  G = 1.35

Partial factor for variable action;  Q = 1.50
Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 16.6 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 10.7 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2 * (fck / 1 N/mm 2 )2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0240
Design bending moment; M x_p =  sx_p  q  l x2 = 6.1 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 119.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.017
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53 * K))) = 113.0 mm
Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 124 mm 2 /m
Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 159 mm 2/m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 159 mm 2 /m

PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 61.1 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0240
Design bending moment; M y_p =  sy_p  q  l x2 = 6.1 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 107.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.021
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 137 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 143 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 143 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 68.0 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0310
Design bending moment; M x_n =  sx_n  q  l x2 = 7.8 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 119.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.022
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53 * K))) = 113.0 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 160 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 159 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 160 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 78.9 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_n = 300 mm
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Actual bar spacing; s x_n = 200 mm

PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0320
Design bending moment; M y_n =  sy_n  q  l x2 = 8.1 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 107.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.028
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 183 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 143 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 183 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 90.6 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = q * l x / 2 = 32.4 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0048
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 58.9 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 65.1 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = q * l x / 2 = 32.4 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0053
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 53.0 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 60.7 kN/m
PASS - Shear capacity is adequate
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000

Stuctural system factor (Table 7.4N); K  = 1.5
Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K  * [11 +1.5*(f ck /1 N/mm 2 )0.5 * 0 / + 3.2*(f ck/1 N/mm 2 ) 0.5 *( 0 / -1) 1.5 ] = 39.31
Mod span-to-depth ratio limit;
ratio lim_x = min(40 * K , min(1.5, (500 N/mm 2 / fyk ) * (A sx_p / A sx_p_m )) * ratio lim_x_bas ) = 58.96
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 32.77
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs B2

12mm bars @ 200 ctrs T2

 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 1
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

CRITICAL EDGE PANEL GUEST ROOMS

RC slab design in accordance with EN1992-1-1:2004 incorporating corrigendum January 2008 and the UK national
annex
Tedds calculation version 1.0.20

Design summary
Description Unit Provided Required Utilisation Result
Short span
Reinf. at midspan mm 2 /m 565 159 0.281 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 201 0.355 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 65.1 35.7 0.548 PASS
Deflection ratio 32.77 58.96 0.556 PASS
Long span
Reinf. at midspan mm 2 /m 565 160 0.283 PASS
Bar spacing at midspan mm 200 300 0.667 PASS
Reinf. at support mm 2 /m 565 212 0.375 PASS
Bar spacing at support mm 200 300 0.667 PASS
Shear at cont. supp kN/m 60.7 35.7 0.588 PASS
Shear at discont. supp kN/m 60.7 26.0 0.428 PASS
Cover
Min cover top mm 25 17 0.680 PASS
Min cover bottom mm 25 17 0.680 PASS

3900

3900

Slab definition
Slab reference name; Critical Edge Panel Guest Rooms
Type of slab; Tw o way spanning w ith restrained edges
Overall slab depth; h = 150 mm
Shorter effective span of panel; lx = 3900 mm
Longer effective span of panel; ly = 3900 mm
Support conditions; One short edge discontinuous
Top outer layer of reinforcement; Short span direction
Bottom outer layer of reinforcement; Short span direction
Loading
Characteristic permanent action; G k = 10.1 kN/m 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 2
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Characteristic variable action; Q k = 2.0 kN/m 2

Partial factor for permanent action;  G = 1.35
Partial factor for variable action;  Q = 1.50
Quasi-permanent value of variable action;  2 = 0.30
Design ultimate load; q =  G  G k +  Q  Q k = 16.6 kN/m 2
Quasi-permanent load; q SLS = 1.0  G k +  2  Q k = 10.7 kN/m 2

Concrete properties
Concrete strength class; C25/30
Characteristic cylinder strength; fck = 25 N/mm 2
Partial factor (Table 2.1N);  C = 1.50
Compressive strength factor (cl. 3.1.6);  cc = 0.85
Design compressive strength (cl. 3.1.6); fcd = 14.2 N/mm 2
Mean axial tensile strength (Table 3.1); fctm = 0.30 N/mm 2 * (fck / 1 N/mm 2 )2/3 = 2.6 N/mm 2
Maximum aggregate size; d g = 20 mm
Reinforcement properties
Characteristic yield strength; fyk = 500 N/mm 2
Partial factor (Table 2.1N);  S = 1.15
Design yield strength (fig. 3.8); fyd = f yk /  S = 434.8 N/mm 2

Concrete cover to reinforcement

Nominal cover to outer top reinforcement; c nom_t = 25 mm
Nominal cover to outer bottom reinforcement; c nom_b = 25 mm
Fire resistance period to top of slab; R top = 60 min
Fire resistance period to bottom of slab; R btm = 60 min
Axia distance to top reinft (Table 5.8); a fi_t = 10 mm
Axia distance to bottom reinft (Table 5.8); a fi_b = 10 mm
Min. top cover requirement with regard to bond; c min,b_t = 12 mm
Min. btm cover requirement with regard to bond; c min,b_b = 12 mm
Reinforcement fabrication; Subject to QA system
Cover allowance for deviation; c dev = 5 mm
Min. required nominal cover to top reinft; c nom_t_min = 17.0 mm
Min. required nominal cover to bottom reinft; c nom_b_min = 17.0 mm
PASS - There is sufficient cover to the top reinforcement
PASS - There is sufficient cover to the bottom reinforcement
Reinforcement design at midspan in short span direction (cl.6.1)
Bending moment coefficient;  sx_p = 0.0290
Design bending moment; M x_p =  sx_p  q  l x2 = 7.3 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_p = 565 mm 2 /m
Effective depth to tension reinforcement; d x_p = h - c nom_b - x_p / 2 = 119.0 mm
K factor; K = M x_p / (b  d x_p 2  f ck ) = 0.021
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_p, d x_p /2  (1 + (1 - 3.53 * K))) = 113.0 mm
Area of reinforcement required for bending; A sx_p_m = M x_p / (fyd  z) = 149 mm 2 /m
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 3
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Minimum area of reinforcement required; A sx_p_min = max(0.26  (f ctm /fyk )  b  d x_p, 0.0013bd x_p ) = 159 mm 2/m
Area of reinforcement required; A sx_p_req = max(A sx_p_m , A sx_p_min) = 159 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_p = (f yk /  S )  min((A sx_p_m /A sx_p), 1.0)  q SLS / q = 73.8 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_x_p = 300 mm
Actual bar spacing; s x_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at midspan in long span direction (cl.6.1)
Bending moment coefficient;  sy_p = 0.0280
Design bending moment; M y_p =  sy_p  q  l x2 = 7.1 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_p = 565 mm 2 /m
Effective depth to tension reinforcement; d y_p = h - c nom_b - x_p - y_p / 2 = 107.0 mm
K factor; K = M y_p / (b  d y_p 2  f ck ) = 0.025
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_p , d y_p /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_p_m = M y_p / (fyd  z) = 160 mm 2 /m
Minimum area of reinforcement required; A sy_p_min = max(0.26  (f ctm /fyk)  b  d y_p , 0.0013bd y_p ) = 143 mm 2/m
Area of reinforcement required; A sy_p_req = max(A sy_p_m , A sy_p_min) = 160 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_p = (f yk /  S )  min((A sy_p_m /A sy_p), 1.0)  q SLS / q = 79.3 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_p = 300 mm
Actual bar spacing; s y_p = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in short span direction (cl.6.1)
Bending moment coefficient;  sx_n = 0.0390
Design bending moment; M x_n =  sx_n  q  l x2 = 9.9 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sx_n = 565 mm 2 /m
Effective depth to tension reinforcement; d x_n = h - c nom_t - x_n / 2 = 119.0 mm
K factor; K = M x_n / (b  d x_n 2  f ck ) = 0.028
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d x_n, d x_n /2  (1 + (1 - 3.53 * K))) = 113.0 mm
Area of reinforcement required for bending; A sx_n_m = M x_n / (fyd  z) = 201 mm 2 /m
Minimum area of reinforcement required; A sx_n_min = max(0.26  (f ctm /fyk )  b  d x_n, 0.0013bd x_n ) = 159 mm 2/m
Area of reinforcement required; A sx_n_req = max(A sx_n_m , A sx_n_min) = 201 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sx_n = (f yk /  S )  min((A sx_n_m /A sx_n), 1.0)  q SLS / q = 99.3 N/mm 2
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 4
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Maximum allowable spacing (Table 7.3N); s max_x_n = 300 mm

Actual bar spacing; s x_n = 200 mm
PASS - The reinforcement spacing is acceptable
Reinforcement design at continuous support in long span direction (cl.6.1)
Bending moment coefficient;  sy_n = 0.0370
Design bending moment; M y_n =  sy_n  q  l x2 = 9.4 kNm/m
Reinforcement provided; 12 mm dia. bars at 200 mm centres
Area provided; A sy_n = 565 mm 2 /m
Effective depth to tension reinforcement; d y_n = h - c nom_t - x_n -  y_n / 2 = 107.0 mm
K factor; K = M y_n / (b  d y_n 2  f ck ) = 0.033
Redistribution ratio;  = 1.0
K’ factor; K’ = 0.598 *  - 0.18 *  2 - 0.21 = 0.208
K < K' - Compression reinforcement is not required
Lever arm; z = min(0.95  d y_n , d y_n /2  (1 + (1 - 3.53 * K))) = 101.6 mm
Area of reinforcement required for bending; A sy_n_m = M y_n / (fyd  z) = 212 mm 2 /m
Minimum area of reinforcement required; A sy_n_min = max(0.26  (f ctm /fyk)  b  d y_n , 0.0013bd y_n ) = 143 mm 2/m
Area of reinforcement required; A sy_n_req = max(A sy_n_m , A sy_n_min) = 212 mm 2 /m
PASS - Area of reinforcement provided exceeds area required
Check reinforcement spacing
Reinforcement service stress;  sy_n = (f yk /  S )  min((A sy_n_m /A sy_n), 1.0)  q SLS / q = 104.8 N/mm 2
Maximum allowable spacing (Table 7.3N); s max_y_n = 300 mm
Actual bar spacing; s y_n = 200 mm
PASS - The reinforcement spacing is acceptable
Shear capacity check at short span continuous support
Shear force; V x_n = 1.1 * q * lx / 2 = 35.7 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d x_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sx_n / (b  d x_n )) = 0.0048
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d x_n
V Rd,c_min = 58.9 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_x_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d x_n) = 65.1 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span continuous support
Shear force; V y_n = 1.1 * q * lx / 2 = 35.7 kN/m
Effective depth factor (cl. 6.2.2); k = min(2.0, 1 + (200 mm / d y_n )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_n / (b  d y_n )) = 0.0053
Minimum shear resistance (Exp. 6.3N); V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d y_n
V Rd,c_min = 53.0 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance (Exp. 6.2a);
V Rd,c_y_n = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck / 1 N/mm 2 )) 0.333  b  d y_n ) = 60.7 kN/m
PASS - Shear capacity is adequate
Shear capacity check at long span discontinuous support
Shear force; V x_d = 0.8 * q * lx / 2 = ;26.0; kN/m;
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 5
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

Reinforcement provided; 12 mm dia. bars at 200 mm centres

Area provided; A sy_d = 565 mm 2 /m
Effective depth; d y_d = h - c nom_b - x_p - y_d / 2 = ;107.0; mm
Effective depth factor; k = min(2.0, 1 + (200 mm / d y_d )0.5 ) = 2.000
Reinforcement ratio;  l = min(0.02, A sy_d / (b  d y_d )) = 0.0053
Minimum shear resistance; V Rd,c_min = 0.035 N/mm 2 * k 1.5 * (f ck / 1 N/mm 2 ) 0.5  b  d y_d
V Rd,c_min = 53.0 kN/m
Shear resistance constant (cl. 6.2.2); C Rd,c = 0.18 N/mm 2 /  C = 0.12 N/mm 2
Shear resistance;
V Rd,c_y_d = max(V Rd,c_min , C Rd,c  k  (100   l  (f ck /1 N/mm 2 )) 0.333  b  d y_d ) = 60.7 kN/m
PASS - Shear capacity is adequate (0.428)
Basic span-to-depth deflection ratio check (cl. 7.4.2)
Reference reinforcement ratio;  0 = (fck / 1 N/mm 2 )0.5 / 1000 = 0.0050
Required tension reinforcement ratio;  = max(0.0035, A sx_p_req / (b  d x_p )) = 0.0035
Required compression reinforcement ratio; ’ = A scx_p_req / (b  d x_p ) = 0.0000
Stuctural system factor (Table 7.4N); K  = 1.5
Basic limit span-to-depth ratio (Exp. 7.16);
ratio lim_x_bas = K  * [11 +1.5*(f ck /1 N/mm 2 )0.5 * 0 / + 3.2*(f ck/1 N/mm 2 ) 0.5 *( 0 / -1) 1.5 ] = 39.31
Mod span-to-depth ratio limit;
ratio lim_x = min(40 * K , min(1.5, (500 N/mm 2 / fyk ) * (A sx_p / A sx_p_m )) * ratio lim_x_bas ) = 58.96
Actual span-to-eff. depth ratio; ratio act_x = lx / d x_p = 32.77
PASS - Actual span-to-effective depth ratio is acceptable

Reinforcement summary
Midspan in short span direction; 12 mm dia. bars at 200 mm centres B1
Midspan in long span direction; 12 mm dia. bars at 200 mm centres B2
Continuous support in short span direction; 12 mm dia. bars at 200 mm centres T1
Continuous support in long span direction; 12 mm dia. bars at 200 mm centres T2
Discontinuous support in long span direction; 12 mm dia. bars at 200 mm centres B2

Reinforcement sketch
The following sketch is indicative only. Note that additional reinforcement may be required in accordance with clauses
9.2.1.2, 9.2.1.4 and 9.2.1.5 of EN 1992-1-1:2004 to meet detailing rules.
 Project Job no.
Julius Nyerere Hydropower Project JNHPP
Mhandisi Consultancy Limited Calcs for Start page no./Revision
Plot No. 305B, Administration Building Slab Design 6
Rweyabura Street, Mikocheni
Calcs by Calcs date Checked by Checked date Approved by Approved date
P O Box 12965, Dar Es Salaam , Tanzania.
GL 3/8/2021 H, Josia 3/8/2021 3/8/2021

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs B1

12mm bars @ 200 ctrs T1

12mm bars @ 200 ctrs T2

12mm bars @ 200 ctrs B2

12mm bars @ 200 ctrs B2

JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-1

Axis: J Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B1 L=3900mm 1B2 L=3900mm 1B3 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
74.394 71.862
61.799

Shear
Force
(Envelope) -44.696
-72.087 -73.05

50.247 46.91 54.207 54.562 52.58

22.478
Moment
(Envelope)
-29.937 -35.661 -34.878

Bending (Top Edge) ...

M (kN.m) 22.5 4.3 50.2 46.9 4.3 54.2 54.6 4.4 52.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.12 0.02 0.28 0.26 0.02 0.30 0.30 0.02 0.29
x (mm) 49.89 49.89 50.62 49.89 49.89 54.86 55.24 49.89 53.11
As (mm2) 121.20 23.29 271.15 252.94 22.98 293.83 295.88 23.67 284.48
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 22.6 29.9 1.5 1.1 35.7 1.8 1.7 34.9 1.9
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.13 0.17 0.01 0.01 0.20 0.01 0.01 0.19 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 121.89 161.42 7.86 5.83 192.29 9.88 9.08 188.07 10.02
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 44.7 61.8 72.1 74.4 73.1 71.9
v (N/mm2) 0.43 0.60 0.70 0.72 0.71 0.70
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-2

Axis: J Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B4 L=3900mm 1B5 L=3900mm 1B6 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
72.57 72.035 74.633

Shear
Force
(Envelope)
-72.347 -72.834 -70.757

52.572 53.096 53.192 51.789 51.715 59.42

Moment
(Envelope)
-35.566 -35.996 -33.464

Bending (Top Edge) ...

M (kN.m) 52.6 4.2 53.1 53.2 4.1 51.8 51.7 7.1 59.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.29 0.02 0.29 0.29 0.02 0.29 0.29 0.04 0.33
x (mm) 53.11 49.89 53.67 53.77 49.89 52.27 52.19 49.89 60.50
As (mm2) 284.44 22.78 287.45 287.99 22.36 279.95 279.53 38.08 324.02
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.8 35.6 1.8 1.8 36.0 1.9 1.8 33.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.20 0.01 0.01 0.20 0.01 0.01 0.19
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 9.91 191.77 9.91 9.91 194.09 10.43 9.98 180.44
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 72.3 72.6 72.8 72.0 70.8 74.6
v (N/mm2) 0.70 0.70 0.71 0.70 0.69 0.72
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-3

Axis: J Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B7 L=4200mm 1B8 L=1800mm 1B9 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
89.623
77.861

32.855
Shear
Force
(Envelope) -34.429

-83.749 -82.487
61.328 65.785
46.044 43.395 42.644 48.052

30.725
Moment
(Envelope)
-46.89 -44.296

Bending (Top Edge) ...

M (kN.m) 61.3 2.0 46.0 43.4 33.9 42.6 48.1 4.4 65.8
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.34 0.01 0.25 0.24 0.19 0.24 0.27 0.02 0.36
x (mm) 62.58 49.89 49.89 49.89 49.89 49.89 49.89 49.89 67.48
As (mm2) 335.17 10.72 248.27 233.99 182.57 229.94 259.10 23.89 361.42
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.9 46.9 9.5 7.5 44.3
d (mm) 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.26 0.05 0.04 0.24
x (mm) 49.89 49.89 49.89 49.89 49.89
As (mm2) 10.30 252.84 51.44 40.35 238.85
As' (mm2) 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 83.7 77.9 34.4 32.9 82.5 89.6
v (N/mm2) 0.81 0.75 0.33 0.32 0.80 0.87
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.1 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 9.35 < 49.74 OK --- 8.69 < 52.27 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-4

Axis: J Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B10 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)

60.256

Shear
Force
(Envelope)
-86.523
66.306

24.991
Moment
(Envelope)
-46.895

Bending (Top Edge) ...

M (kN.m) 66.3 3.8 25.0
d (mm) 449.0 449.0 449.0
K/K' 0.37 0.02 0.14
x (mm) 68.06 49.89 49.89
As (mm2) 364.51 20.63 134.75
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.2 46.9 30.8
d (mm) 449.0 449.0 449.0
K/K' 0.01 0.26 0.17
x (mm) 49.89 49.89 49.89
As (mm2) 6.53 252.86 165.83
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 86.5 60.3
v (N/mm2) 0.84 0.58
vc (N/mm2) 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 49.74 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-5

Axis: I Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B11 L=3900mm 1B12 L=3900mm 1B13 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
124.544
101.262 105.148

Shear
Force
(Envelope)
-88.092
-108.114 -103.591
92.509 90.374
75.471 75.893 79.228

27.329
Moment
(Envelope)
-53.125 -57.352
-78.169
Bending (Top Edge) ...
M (kN.m) 27.3 5.6 92.5 90.4 12.7 75.5 75.9 7.7 79.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.15 0.03 0.51 0.50 0.07 0.42 0.42 0.04 0.44
x (mm) 49.89 49.89 98.12 95.59 49.89 78.33 78.81 49.89 82.61
As (mm2) 147.36 30.16 525.56 511.99 68.75 419.53 422.10 41.26 442.48
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 43.1 78.2 2.3 53.1 5.8 57.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.24 0.43 0.01 0.29 0.03 0.32
x (mm) 49.89 81.40 49.89 53.70 49.89 58.25
As (mm2) 232.63 435.99 12.54 287.61 31.41 312.00
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 88.1 124.5 108.1 101.3 103.6 105.1
v (N/mm2) 0.85 1.21 1.05 0.98 1.00 1.02
vc (N/mm2) 0.50 0.50 0.50 0.50 0.44 0.50 0.50 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.5 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 38.0 OK 8.69 < 44.12 OK 8.69 < 40.63 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 603.19 603.19 603.19 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16

Top.Sup.

Bot.Bars 3H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-6

Axis: I Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B14 L=3900mm 1B15 L=3900mm 1B16 L=4200mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
103.649 107.972 115.357

Shear
Force
(Envelope)
-105.12 -101.225
-122.745
79.295 90.077 92.857
76.068 75.727 70.774

Moment
(Envelope)
-57.225 -52.974
-73.409

Bending (Top Edge) ...

M (kN.m) 79.3 7.7 76.1 75.7 12.3 90.1 92.9 4.1 70.8
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.44 0.04 0.42 0.42 0.07 0.50 0.51 0.02 0.39
x (mm) 82.69 49.89 79.01 78.62 49.89 95.24 98.54 49.89 73.03
As (mm2) 442.89 41.52 423.16 421.09 66.23 510.11 527.78 22.12 391.17
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 2.7 57.2 6.1 53.0 2.3 6.0 73.4 7.9
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.32 0.03 0.29 0.01 0.03 0.41 0.04
x (mm) 49.89 58.11 49.89 53.54 49.89 49.89 75.99 49.89
As (mm2) 14.55 311.26 33.01 286.74 12.14 32.41 407.04 42.34
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 105.1 103.6 101.2 108.0 122.7 115.4
v (N/mm2) 1.02 1.00 0.98 1.05 1.19 1.12
vc (N/mm2) 0.50 0.44 0.50 0.50 0.44 0.50 0.50 0.50 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 121.5
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 40.73 OK 8.69 < 44.25 OK 9.35 < 40.46 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 603.19 603.19 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 3H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-7

Axis: I Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B17 L=1800mm 1B18 L=3900mm 1B19 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
123.162
77.092
35.238
Shear
Force
(Envelope) -39.786

-112.938 -112.335
90.667 89.955
62.395 56.177 63.632
27.563
48.987
Moment
(Envelope)

-67.694 -64.44

Bending (Top Edge) ...

M (kN.m) 62.4 52.4 56.2 63.6 5.4 90.7 90.0 8.7 27.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.35 0.29 0.31 0.35 0.03 0.50 0.50 0.05 0.15
x (mm) 63.75 52.92 56.98 65.10 49.89 95.94 95.09 49.89 49.89
As (mm2) 341.43 283.46 305.20 348.71 28.88 513.84 509.34 46.65 148.62
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 67.7 2.6 2.0 64.4 35.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.37 0.01 0.01 0.36 0.20
x (mm) 49.89 69.60 49.89 49.89 65.99 49.89
As (mm2) 66.03 372.76 13.94 10.67 353.47 191.82
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 39.8 35.2 112.9 123.2 112.3 77.1
v (N/mm2) 0.39 0.34 1.09 1.19 1.09 0.75
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.1 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d --- 8.69 < 33.14 OK 8.69 < 35.35 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-8

Axis: H Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B20 L=3900mm 1B21 L=3900mm 1B22 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
109.456 98.707 100.379

Shear
Force
(Envelope)
-79.525
-101.88 -100.252

80.893 79.499 73.579 73.663 74.263

27.675
Moment
(Envelope)
-50.268 -52.252
-70.031

Bending (Top Edge) ...

M (kN.m) 27.7 5.5 80.9 79.5 8.4 73.6 73.7 6.7 74.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.15 0.03 0.45 0.44 0.05 0.41 0.41 0.04 0.41
x (mm) 49.89 49.89 84.52 82.92 49.89 76.19 76.28 49.89 76.96
As (mm2) 149.23 29.80 452.72 444.14 45.33 408.07 408.57 35.99 412.21
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 36.7 70.0 2.1 50.3 4.3 52.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.20 0.39 0.01 0.28 0.02 0.29
x (mm) 49.89 72.20 49.89 50.65 49.89 52.76
As (mm2) 197.80 386.72 11.19 271.27 23.43 282.61
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 79.5 109.5 101.9 98.7 100.3 100.4
v (N/mm2) 0.77 1.06 0.99 0.96 0.97 0.97
vc (N/mm2) 0.44 0.44 0.50 0.50 0.44 0.50 0.50 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.1 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 31.62 OK 8.69 < 46.64 OK 8.69 < 44.87 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-9

Axis: H Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B23 L=3900mm 1B24 L=3900mm 1B25 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
100.273 99.803 103.083

Shear
Force
(Envelope)
-100.213 -100.72 -97.921

74.248 74.436 74.509 72.577 72.285 83.43

Moment
(Envelope)
-52.074 -52.774 -49.324

Bending (Top Edge) ...

M (kN.m) 74.2 6.8 74.4 74.5 6.6 72.6 72.3 10.3 83.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.41 0.04 0.41 0.41 0.04 0.40 0.40 0.06 0.46
x (mm) 76.94 49.89 77.15 77.24 49.89 75.06 74.73 49.89 87.46
As (mm2) 412.12 36.73 413.25 413.69 35.84 402.02 400.25 55.42 468.43
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 5.0 52.1 5.0 52.8 5.1 49.3 2.1
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.03 0.29 0.03 0.29 0.03 0.27 0.01
x (mm) 49.89 52.57 49.89 53.32 49.89 49.89 49.89
As (mm2) 26.86 281.59 26.81 285.60 27.33 265.96 11.46
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 100.2 100.3 100.7 99.8 97.9 103.1
v (N/mm2) 0.97 0.97 0.98 0.97 0.95 1.00
vc (N/mm2) 0.50 0.44 0.50 0.50 0.44 0.44 0.44 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 45.03 OK 8.69 < 44.42 OK 8.69 < 47.5 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 603.19 603.19 402.12 402.12 402.12 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 2H16 2H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-10

Axis: H Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B26 L=4200mm 1B27 L=1800mm 1B28 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
110.898 124.612

31.469
Shear
Force
(Envelope) -43.927

-115.162 -111.239
85.565 91.757
70.633 63.482
51.103 58.974
45.057
Moment
(Envelope)
-65.414 -69.119

Bending (Top Edge) ...

M (kN.m) 85.6 3.2 70.6 63.5 51.3 51.1 59.0 4.9 91.8
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.47 0.02 0.39 0.35 0.28 0.28 0.33 0.03 0.51
x (mm) 89.94 49.89 72.88 64.94 51.77 51.54 60.01 49.89 97.23
As (mm2) 481.73 17.35 390.33 347.82 277.27 276.03 321.43 26.36 520.77
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 4.6 65.4 5.1 14.3 69.1 2.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.03 0.36 0.03 0.08 0.38 0.01
x (mm) 49.89 67.07 49.89 49.89 71.18 49.89
As (mm2) 24.78 359.23 27.69 77.35 381.26 13.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 115.2 110.9 43.9 31.5 111.2 124.6
v (N/mm2) 1.12 1.07 0.43 0.30 1.08 1.21
vc (N/mm2) 0.50 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.1 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 1100.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-275
Deflection Check ...
L/d 9.35 < 34.68 OK --- 8.69 < 32.21 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12 402.12 402.12 402.12 402.12 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 2H16 2H16 2H16 2H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-11

Axis: H Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B29 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)

77.107

Shear
Force
(Envelope)
-112.571
90.797

27.352
Moment
(Envelope)
-63.491

Bending (Top Edge) ...

M (kN.m) 90.8 8.7 27.4
d (mm) 449.0 449.0 449.0
K/K' 0.50 0.05 0.15
x (mm) 96.09 49.89 49.89
As (mm2) 514.67 46.96 147.48
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.9 63.5 35.4
d (mm) 449.0 449.0 449.0
K/K' 0.01 0.35 0.20
x (mm) 49.89 64.95 49.89
As (mm2) 10.34 347.88 191.05
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 112.6 77.1
v (N/mm2) 1.09 0.75
vc (N/mm2) 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 36.02 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 3H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-12

Axis: G Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B30 L=3900mm 1B31 L=3900mm 1B32 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
79.869
67.001 68.617

Shear
Force
(Envelope)
-59.047 -68.098
-70.117
57.077 53.855 49.448
48.031 48.758
24.431
Moment
(Envelope)
-29.935 -32.19
-44.815

Bending (Top Edge) ...

M (kN.m) 24.4 2.1 57.1 53.9 6.0 48.0 48.8 3.7 49.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.14 0.01 0.32 0.30 0.03 0.27 0.27 0.02 0.27
x (mm) 49.89 49.89 57.95 54.48 49.89 49.89 49.89 49.89 49.89
As (mm2) 131.74 11.41 310.41 291.81 32.47 258.99 262.91 19.94 266.63
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 30.2 44.8 1.7 1.5 29.9 1.7 1.8 32.2 1.8
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.17 0.25 0.01 0.01 0.17 0.01 0.01 0.18 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 162.65 241.65 8.93 8.26 161.41 9.21 9.84 173.57 9.44
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 59.0 79.9 70.1 67.0 68.1 68.6
v (N/mm2) 0.57 0.77 0.68 0.65 0.66 0.66
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 51.75 OK 8.69 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-13

Axis: G Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B33 L=3900mm 1B34 L=3900mm 1B35 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
68.411 67.763 72.216

Shear
Force
(Envelope)
-68.299 -68.988 -65.458
60.606
49.304 49.482 49.699 47.797 46.777

Moment
(Envelope)
-31.655 -32.574 -28.201

Bending (Top Edge) ...

M (kN.m) 49.3 3.9 49.5 49.7 3.7 47.8 46.8 10.2 60.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.27 0.02 0.27 0.27 0.02 0.26 0.26 0.06 0.34
x (mm) 49.89 49.89 49.89 50.04 49.89 49.89 49.89 49.89 61.79
As (mm2) 265.85 20.94 266.81 268.02 19.80 257.73 252.23 54.81 330.95
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.7 31.7 1.7 1.7 32.6 2.1 1.7 28.2 1.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.18 0.01 0.01 0.18 0.01 0.01 0.16 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 9.39 170.69 9.31 9.39 175.64 11.07 9.42 152.06 6.20
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 68.3 68.4 69.0 67.8 65.5 72.2
v (N/mm2) 0.66 0.66 0.67 0.66 0.63 0.70
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-14

Axis: G Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B36 L=4200mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
64.176

Shear
Force
(Envelope)
-86.619
64.387

25.689

Moment
(Envelope)

-51.946

Bending (Top Edge) ...

M (kN.m) 64.4 1.9 25.7
d (mm) 449.0 449.0 449.0
K/K' 0.36 0.01 0.14
x (mm) 65.94 49.89 49.89
As (mm2) 353.16 10.01 138.52
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.7 51.9 32.5
d (mm) 449.0 449.0 449.0
K/K' 0.01 0.29 0.18
x (mm) 49.89 52.44 49.89
As (mm2) 8.93 280.86 175.14
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 86.6 64.2
v (N/mm2) 0.84 0.62
vc (N/mm2) 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 9.35 < 45.14 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-15

Axis: F Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B37 L=1800mm 1B38 L=3900mm 1B39 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
126.425
76.811
58.615

Shear
Force -24.127
(Envelope)
-109.472 -112.937
93.626 92.139

45.896 53.98
21.224 27.239
Moment 11.222
(Envelope) -11.439

-70.773 -63.222

Bending (Top Edge) ...

M (kN.m) 21.2 24.6 45.9 54.0 5.0 93.6 92.1 9.3 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.12 0.14 0.25 0.30 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 54.61 49.89 99.46 97.68 49.89 49.89
As (mm2) 114.44 132.47 247.48 292.52 26.75 532.70 523.20 50.14 146.87
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 11.4 6.5 14.8 70.8 2.4 4.6 63.2 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.06 0.04 0.08 0.39 0.01 0.03 0.35 0.19
x (mm) 49.89 49.89 49.89 73.03 49.89 49.89 64.65 49.89
As (mm2) 61.68 35.14 79.61 391.17 12.79 24.97 346.30 190.12
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 24.1 58.6 109.5 126.4 112.9 76.8
v (N/mm2) 0.23 0.57 1.06 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.15 OK 8.69 < 36.21 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-16

Axis: E Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B40 L=1800mm 1B41 L=3900mm 1B42 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.692
76.793
60.379

Shear
Force -22.047
(Envelope)
-110.293 -112.847
93.121 91.787
48.209 56.631
20.212 27.237
Moment 10.331
(Envelope) -12.302

-69.666 -63.336

Bending (Top Edge) ...

M (kN.m) 20.2 26.7 48.2 56.6 5.0 93.1 91.8 9.1 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.27 0.31 0.03 0.51 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.47 49.89 98.85 97.26 49.89 49.89
As (mm2) 108.99 144.04 259.95 307.83 26.90 529.47 520.96 48.97 146.86
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.3 6.5 13.0 69.7 2.4 4.7 63.3 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.39 0.01 0.03 0.35 0.20
x (mm) 49.89 49.89 49.89 71.79 49.89 49.89 64.78 49.89
As (mm2) 66.33 34.93 70.33 384.53 12.77 25.36 346.97 190.47
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.5 60.4 110.3 125.7 112.8 76.8
v (N/mm2) 0.22 0.58 1.07 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.85 OK 8.69 < 36.13 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-17

Axis: D Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B43 L=1800mm 1B44 L=3900mm 1B45 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.855
76.743
60.099

Shear
Force -22.336
(Envelope)
-110.109 -112.907
93.34 91.982

47.825 56.147
20.308 27.182
Moment 10.206
(Envelope) -12.182

-69.805 -63.302

Bending (Top Edge) ...

M (kN.m) 20.3 26.4 47.8 56.1 5.0 93.3 92.0 9.2 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.26 0.31 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 56.95 49.89 99.11 97.50 49.89 49.89
As (mm2) 109.50 142.16 257.88 305.02 27.08 530.87 522.20 49.41 146.57
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.5 13.3 69.8 2.4 4.6 63.3 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.39 0.01 0.03 0.35 0.20
x (mm) 49.89 49.89 49.89 71.95 49.89 49.89 64.74 49.89
As (mm2) 65.69 35.06 71.85 385.36 12.71 24.93 346.77 190.41
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.4 60.1 110.1 125.9 112.9 76.7
v (N/mm2) 0.22 0.58 1.07 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.77 OK 8.69 < 36.16 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-18

Axis: C Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B46 L=1800mm 1B47 L=3900mm 1B48 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
126.005
80.357
60.418

Shear
Force -21.922
(Envelope)
-110.541 -116.61
94.056 93.13

48.366 57.049
20.173 27.858
Moment 11.305
(Envelope) -12.216

-69.593 -67.049

Bending (Top Edge) ...

M (kN.m) 20.2 27.0 48.4 57.0 5.7 94.1 93.1 8.5 27.9
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.27 0.32 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.92 49.89 99.97 98.86 49.89 49.89
As (mm2) 108.77 145.33 260.79 310.24 30.62 535.45 529.52 45.88 150.21
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.4 12.7 69.6 2.4 1.9 67.0 36.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.38 0.01 0.01 0.37 0.20
x (mm) 49.89 49.89 49.89 71.71 49.89 49.89 68.88 49.89
As (mm2) 65.87 34.37 68.57 384.10 12.88 10.33 368.93 197.08
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 24.5 60.4 110.5 126.0 116.6 80.4
v (N/mm2) 0.24 0.59 1.07 1.22 1.13 0.78
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.9 OK 8.69 < 33.57 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-19

Axis: B Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B49 L=1800mm 1B50 L=3900mm 1B51 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
141.926

64.937 56.601

Shear
Force -17.229
(Envelope)
-99.05
-124.505
103.945 98.321
56.619 66.213
20.134 22.151
Moment 13.419
(Envelope) -12.096
-41.064

-99.062
Bending (Top Edge) ...
M (kN.m) 20.1 28.3 56.6 66.2 103.9 98.3 15.3 22.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.16 0.31 0.37 0.57 0.54 0.08 0.12
x (mm) 49.89 49.89 57.46 67.95 111.98 105.10 49.89 49.89
As (mm2) 108.56 152.58 307.76 363.96 599.77 562.95 82.40 119.44
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.1 4.0 13.4 99.1 0.4 41.1 28.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.02 0.07 0.55 0.00 0.23 0.16
x (mm) 49.89 49.89 49.89 106.00 49.89 49.89 49.89
As (mm2) 65.22 21.34 72.03 567.77 2.21 221.42 154.62
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 26.9 64.9 124.5 141.9 99.1 56.6
v (N/mm2) 0.26 0.63 1.21 1.37 0.96 0.55
vc (N/mm2) 0.44 0.44 0.44 0.44 0.50 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 121.5 114.7
Td (kN.m) 0.0 0.3 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1125.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-225 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 28.93 OK 8.69 < 55.64 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 3H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-20

Axis: A Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B52 L=1800mm 1B53 L=3900mm 1B54 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
106.16
56.549
37.288
Shear
Force -17.709
(Envelope)
-68.347
-96.998
74.367 69.435
47.50 52.911
18.943 19.596
Moment 11.327
(Envelope) -13.043
-24.252

-79.914
Bending (Top Edge) ...
M (kN.m) 18.9 22.3 47.5 52.9 74.4 69.4 12.9 19.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.10 0.12 0.26 0.29 0.41 0.38 0.07 0.11
x (mm) 49.89 49.89 49.89 53.47 77.08 71.53 49.89 49.89
As (mm2) 102.14 120.35 256.13 286.38 412.83 383.15 69.79 105.66
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 13.0 5.4 9.8 79.9 2.1 24.3 21.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.03 0.05 0.44 0.01 0.13 0.12
x (mm) 49.89 49.89 49.89 83.40 49.89 49.89 49.89
As (mm2) 70.33 29.25 52.98 446.70 11.33 130.77 117.00
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 25.0 56.5 97.0 106.2 68.3 37.3
v (N/mm2) 0.24 0.55 0.94 1.03 0.66 0.36
vc (N/mm2) 0.44 0.44 0.44 0.44 0.50 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 121.5 114.7
Td (kN.m) 0.0 0.3 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 37.13 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 3H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-21

Axis: 1 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B57 L=1800mm 1B56 L=3900mm 1B55 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
92.122
56.508
38.431
Shear
Force -17.731
(Envelope)
-66.78
-101.242
67.769 64.651
47.355 52.515
18.853 20.535
Moment 11.219
(Envelope) -13.115
-24.983

-75.239
Bending (Top Edge) ...
M (kN.m) 18.9 22.2 47.4 52.5 0.5 67.8 64.7 10.4 20.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.10 0.12 0.26 0.29 0.00 0.37 0.36 0.06 0.11
x (mm) 49.89 49.89 49.89 53.04 49.89 69.68 66.23 49.89 49.89
As (mm2) 101.66 119.61 255.34 284.11 2.56 373.21 354.72 55.82 110.73
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 13.1 5.5 16.0 75.2 25.0 21.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.03 0.09 0.42 0.14 0.12
x (mm) 49.89 49.89 49.89 78.06 49.89 49.89
As (mm2) 70.72 29.75 86.39 418.12 134.71 116.50
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 25.1 56.5 101.2 92.1 66.8 38.4
v (N/mm2) 0.24 0.55 0.98 0.89 0.65 0.37
vc (N/mm2) 0.44 0.44 0.44 0.44 0.50 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 121.5 114.7
Td (kN.m) 0.0 0.3 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 39.49 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 3H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-22

Axis: 2 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B60 L=1800mm 1B59 L=3900mm 1B58 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
127.925

64.672 54.332

Shear
Force -17.454
(Envelope)
-93.777
-128.716
96.713 91.649
56.117 65.339
20.066 21.905
Moment 13.164
(Envelope) -12.121
-39.166

-95.615
Bending (Top Edge) ...
M (kN.m) 20.1 27.8 56.1 65.3 1.6 96.7 91.6 13.8 21.9
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.31 0.36 0.01 0.53 0.51 0.08 0.12
x (mm) 49.89 49.89 56.92 66.99 49.89 103.16 97.10 49.89 49.89
As (mm2) 108.20 149.88 304.85 358.79 8.65 552.54 520.08 74.27 118.11
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.1 4.1 19.8 95.6 0.0 39.2 28.0
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.02 0.11 0.53 0.00 0.22 0.16
x (mm) 49.89 49.89 49.89 101.84 49.89 49.89 49.89
As (mm2) 65.36 22.16 106.99 545.46 0.00 211.19 151.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 26.3 64.7 128.7 127.9 93.8 54.3
v (N/mm2) 0.26 0.63 1.25 1.24 0.91 0.53
vc (N/mm2) 0.44 0.44 0.44 0.44 0.50 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 121.5 114.7
Td (kN.m) 0.0 0.2 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 1125.0 1000.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-225 H8-300 H8-250 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 30.26 OK 8.69 < 57.75 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 3H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-23

Axis: 3 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B63 L=1800mm 1B62 L=3900mm 1B61 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.366
77.024
60.449

Shear
Force -21.847
(Envelope)
-110.547 -112.538
92.281 90.892
48.462 56.938
20.164 27.403
Moment 10.426
(Envelope) -12.176

-69.844 -63.526

Bending (Top Edge) ...

M (kN.m) 20.2 26.9 48.5 56.9 4.7 92.3 90.9 8.7 27.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.27 0.31 0.03 0.51 0.50 0.05 0.15
x (mm) 49.89 49.89 49.89 57.80 49.89 97.85 96.20 49.89 49.89
As (mm2) 108.73 145.01 261.31 309.60 25.39 524.10 515.28 47.17 147.76
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.3 12.8 69.8 1.9 63.5 35.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.03 0.07 0.39 0.01 0.35 0.19
x (mm) 49.89 49.89 49.89 71.99 49.89 64.99 49.89
As (mm2) 65.65 34.06 69.15 385.60 10.29 348.08 189.54
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.5 60.4 110.5 125.4 112.5 77.0
v (N/mm2) 0.22 0.59 1.07 1.21 1.09 0.75
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.74 OK 8.69 < 36.0 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-24

Axis: 4 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B66 L=1800mm 1B65 L=3900mm 1B64 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.84
76.738
60.134

Shear
Force -22.249
(Envelope)
-110.121 -112.896
93.334 91.961

47.878 56.193
20.246 27.175
Moment 10.21
(Envelope) -12.193

-69.78 -63.305

Bending (Top Edge) ...

M (kN.m) 20.2 26.4 47.9 56.2 5.0 93.3 92.0 9.2 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.26 0.31 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.00 49.89 99.11 97.47 49.89 49.89
As (mm2) 109.17 142.47 258.16 305.29 27.09 530.83 522.07 49.35 146.53
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.5 13.3 69.8 2.4 4.6 63.3 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.39 0.01 0.03 0.35 0.20
x (mm) 49.89 49.89 49.89 71.92 49.89 49.89 64.74 49.89
As (mm2) 65.74 35.02 71.63 385.21 12.71 24.91 346.78 190.27
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.3 60.1 110.1 125.8 112.9 76.7
v (N/mm2) 0.22 0.58 1.07 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.78 OK 8.69 < 36.15 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-25

Axis: 5 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B69 L=1800mm 1B68 L=3900mm 1B67 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.751
76.775
60.216

Shear
Force -22.232
(Envelope)
-110.201 -112.854
93.151 91.812

48.004 56.348
20.295 27.221
Moment 10.267
(Envelope) -12.213

-69.778 -63.348

Bending (Top Edge) ...

M (kN.m) 20.3 26.5 48.0 56.3 5.0 93.2 91.8 9.1 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.27 0.31 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.16 49.89 98.89 97.30 49.89 49.89
As (mm2) 109.43 142.95 258.84 306.18 26.81 529.66 521.12 49.03 146.78
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.5 13.2 69.8 2.4 4.7 63.3 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.39 0.01 0.03 0.35 0.20
x (mm) 49.89 49.89 49.89 71.92 49.89 49.89 64.79 49.89
As (mm2) 65.86 34.91 71.14 385.20 12.75 25.31 347.04 190.42
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.5 60.2 110.2 125.8 112.9 76.8
v (N/mm2) 0.22 0.58 1.07 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.78 OK 8.69 < 36.12 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-26

Axis: 6 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B72 L=1800mm 1B71 L=3900mm 1B70 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.833
76.764
60.084

Shear
Force -22.38
(Envelope)
-110.148 -112.889
93.27 91.923

47.808 56.221
20.365 27.218
Moment 10.224
(Envelope) -12.173

-69.802 -63.311

Bending (Top Edge) ...

M (kN.m) 20.4 26.4 47.8 56.2 5.0 93.3 91.9 9.1 27.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.26 0.31 0.03 0.52 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.03 49.89 99.03 97.43 49.89 49.89
As (mm2) 109.81 142.35 257.78 305.45 26.95 530.42 521.82 49.29 146.76
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.2 6.5 13.3 69.8 2.4 4.7 63.3 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.07 0.39 0.01 0.03 0.35 0.20
x (mm) 49.89 49.89 49.89 71.95 49.89 49.89 64.75 49.89
As (mm2) 65.64 35.05 71.85 385.35 12.74 25.09 346.82 190.49
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.4 60.1 110.1 125.8 112.9 76.8
v (N/mm2) 0.22 0.58 1.07 1.22 1.09 0.74
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.77 OK 8.69 < 36.15 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-27

Axis: 7 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B75 L=1800mm 1B74 L=3900mm 1B73 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
125.504
76.938
60.682

Shear
Force -21.806
(Envelope)
-110.366 -112.729
92.801 91.456
48.641 56.726
20.112 27.332
Moment 10.422
(Envelope) -12.417

-69.717 -63.40

Bending (Top Edge) ...

M (kN.m) 20.1 26.7 48.6 56.7 4.9 92.8 91.5 9.0 27.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.11 0.15 0.27 0.31 0.03 0.51 0.51 0.05 0.15
x (mm) 49.89 49.89 49.89 57.57 49.89 98.47 96.87 49.89 49.89
As (mm2) 108.44 144.10 262.28 308.37 26.51 527.42 518.86 48.60 147.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 12.4 6.4 15.8 69.7 2.4 4.9 63.4 35.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.04 0.09 0.39 0.01 0.03 0.35 0.19
x (mm) 49.89 49.89 49.89 71.85 49.89 49.89 64.85 49.89
As (mm2) 66.96 34.72 85.40 384.84 12.77 26.49 347.34 190.13
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 22.8 60.7 110.4 125.5 112.7 76.9
v (N/mm2) 0.22 0.59 1.07 1.22 1.09 0.75
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.50 0.50 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 1100.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-275 H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.01 < 57.97 OK 8.69 < 31.82 OK 8.69 < 36.09 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-28

Axis: 8 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B76 L=3900mm 1B77 L=3800mm 1B78 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
79.567 68.959
64.991

Shear
Force
(Envelope) -59.185 -68.185 -67.864

56.027 52.292 46.791 47.607 49.455

24.403
Moment
(Envelope)
-27.827 -32.495
-45.114

Bending (Top Edge) ...

M (kN.m) 24.4 1.5 56.0 52.3 6.8 46.8 47.6 3.5 49.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.13 0.01 0.31 0.29 0.04 0.26 0.26 0.02 0.27
x (mm) 49.89 49.89 56.82 52.81 49.89 49.89 49.89 49.89 49.89
As (mm2) 131.59 8.11 304.33 282.83 36.93 252.30 256.70 18.92 266.66
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 30.3 45.1 1.7 3.1 27.8 1.7 1.9 32.5 1.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.17 0.25 0.01 0.02 0.15 0.01 0.01 0.18 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 163.15 243.26 9.18 16.68 150.04 9.10 10.31 175.22 9.19
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 59.2 79.6 68.2 65.0 67.9 69.0
v (N/mm2) 0.57 0.77 0.66 0.63 0.66 0.67
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 51.46 OK 8.46 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-29

Axis: 8 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B79 L=3900mm 1B80 L=3900mm 1B81 L=2100mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)

68.926 67.194
38.958
Shear
Force
(Envelope) -39.554
-67.945 -71.813

49.24 50.681 50.845

38.865 37.50
27.498
Moment 9.792
(Envelope)
-30.802 -33.451

Bending (Top Edge) ...

M (kN.m) 49.2 4.0 50.7 50.8 3.0 38.9 37.5 18.4 27.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.27 0.02 0.28 0.28 0.02 0.21 0.21 0.10 0.15
x (mm) 49.89 49.89 51.09 51.26 49.89 49.89 49.89 49.89 49.89
As (mm2) 265.50 21.66 273.62 274.56 16.02 209.56 202.20 99.31 148.27
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.7 30.8 1.4 1.7 33.5 7.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.17 0.01 0.01 0.18 0.04
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 9.18 166.09 7.68 9.30 180.37 39.12
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 67.9 68.9 71.8 67.2 39.6 39.0
v (N/mm2) 0.66 0.67 0.70 0.65 0.38 0.38
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 57.97 OK ---
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-30

Axis: 8 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B82 L=1800mm 1B83 L=3900mm 1B84 L=3900mm
BwxH (mm) 230 x 900 230 x 900 230 x 900
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
115.381
81.289
36.141
Shear
Force
(Envelope) -45.905
-102.353 -108.506
61.917 61.373
34.689 26.095 32.062 22.856
Moment 15.544
(Envelope) -6.386

-82.238 -74.909
Bending (Top Edge) ...
M (kN.m) 34.7 17.9 26.1 32.1 61.9 61.4 22.9
d (mm) 849.0 849.0 849.0 849.0 849.0 849.0 849.0
K/K' 0.05 0.03 0.04 0.05 0.10 0.09 0.04
x (mm) 94.33 94.33 94.33 94.33 94.33 94.33 94.33
As (mm2) 98.92 51.09 74.41 91.43 176.57 175.01 65.18
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 269.10 269.10 269.10 269.10 269.10 269.10 269.10 269.10 269.10
Bending (Bottom Edge) ...
M (kN.m) 0.5 6.4 0.6 35.7 82.2 20.7 9.4 74.9 46.4
d (mm) 849.0 849.0 849.0 849.0 849.0 849.0 849.0 849.0 849.0
K/K' 0.00 0.01 0.00 0.06 0.13 0.03 0.01 0.12 0.07
x (mm) 94.33 94.33 94.33 94.33 94.33 94.33 94.33 94.33 94.33
As (mm2) 1.42 18.21 1.75 101.82 234.51 58.95 26.67 213.62 132.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 269.10 269.10 269.10 269.10 269.10 269.10 269.10 269.10 269.10
Shear and Bending Design ...
Vd (kN) 45.9 36.1 102.4 115.4 108.5 81.3
v (N/mm2) 0.24 0.19 0.52 0.59 0.56 0.42
vc (N/mm2) 0.31 0.31 0.31 0.31 0.31 0.31 0.31 0.31 0.31
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 186.9 186.9 186.9
Td (kN.m) 0.1 0.0 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 2.12 < 55.34 OK 4.59 < 55.34 OK 4.59 < 55.34 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar 3H16 3H16 3H16

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-31

Axis: 9 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B85 L=3900mm 1B86 L=3800mm 1B87 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
114.48 101.304
94.488

Shear
Force
(Envelope)
-84.462
-99.388 -99.512
82.577 79.94 74.981
70.086 70.771

28.537
Moment
(Envelope)
-45.82 -53.115
-78.24
Bending (Top Edge) ...
M (kN.m) 28.5 4.1 82.6 79.9 11.9 70.1 70.8 6.6 75.0
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.16 0.02 0.46 0.44 0.07 0.39 0.39 0.04 0.41
x (mm) 49.89 49.89 86.47 83.43 49.89 72.26 73.03 49.89 77.77
As (mm2) 153.88 21.88 463.14 446.85 63.95 387.05 391.15 35.61 416.56
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 38.9 78.2 2.0 45.8 4.2 53.1
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.22 0.43 0.01 0.25 0.02 0.29
x (mm) 49.89 81.48 49.89 49.89 49.89 53.69
As (mm2) 209.95 436.43 10.93 247.07 22.50 287.56
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 84.5 114.5 99.4 94.5 99.5 101.3
v (N/mm2) 0.82 1.11 0.96 0.91 0.96 0.98
vc (N/mm2) 0.50 0.50 0.50 0.50 0.44 0.44 0.44 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.5 114.7 114.7
Td (kN.m) 0.1 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 37.96 OK 8.46 < 50.77 OK 8.69 < 44.12 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 402.12 402.12 402.12 603.19
Bot Edge 603.19 603.19 603.19 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 2H16 2H16 3H16

Top.Sup.

Bot.Bars 3H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-32

Axis: 9 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B88 L=3900mm 1B89 L=3900mm 1B90 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
100.028 100.554 101.049

Shear
Force
(Envelope)
-100.433 -100.227 -100.255
74.817 74.004 73.984 73.976 73.797 73.68

Moment
(Envelope)
-51.925 -51.959 -52.307

Bending (Top Edge) ...

M (kN.m) 74.8 6.9 74.0 74.0 6.5 74.0 73.8 6.9 73.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.41 0.04 0.41 0.41 0.04 0.41 0.41 0.04 0.41
x (mm) 77.59 49.89 76.67 76.64 49.89 76.64 76.43 49.89 76.30
As (mm2) 415.56 37.03 410.64 410.52 35.30 410.47 409.39 37.15 408.68
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 4.9 51.9 4.9 52.0 2.7 52.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.03 0.29 0.03 0.29 0.02 0.29
x (mm) 49.89 52.41 49.89 52.45 49.89 52.82
As (mm2) 26.41 280.73 26.61 280.93 14.80 282.92
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 100.4 100.0 100.2 100.6 100.3 101.0
v (N/mm2) 0.97 0.97 0.97 0.97 0.97 0.98
vc (N/mm2) 0.50 0.44 0.50 0.50 0.44 0.50 0.50 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 45.16 OK 8.69 < 45.13 OK 8.69 < 44.82 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-33

Axis: 9 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B91 L=3900mm 1B92 L=3900mm
BwxH (mm) 230 x 500 230 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
103.154
86.566

Shear
Force
(Envelope)
-97.768
-118.097
73.25 82.833 85.028

28.554
Moment
(Envelope)
-49.332
-72.733
Bending (Top Edge) ...
M (kN.m) 73.3 9.5 82.8 85.0 4.8 28.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.41 0.05 0.46 0.47 0.03 0.16
x (mm) 75.82 49.89 86.76 89.31 49.89 49.89
As (mm2) 406.08 51.34 464.72 478.38 26.12 153.96
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 2.9 49.3 1.9 5.6 72.7 39.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.02 0.27 0.01 0.03 0.40 0.22
x (mm) 49.89 49.89 49.89 49.89 75.23 49.89
As (mm2) 15.54 266.00 10.27 30.32 402.96 213.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 97.8 103.2 118.1 86.6
v (N/mm2) 0.95 1.00 1.14 0.84
vc (N/mm2) 0.50 0.44 0.50 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 121.5
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 47.49 OK 8.69 < 40.83 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16 2H16
Top.Sup. 3H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 3H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-34

Axis: 10 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B93 L=3800mm 1B94 L=3900mm 1B95 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
124.326
101.745 104.914

Shear
Force
(Envelope)
-87.497
-107.596 -103.812
90.735 88.877
75.993 76.333 78.755

26.773
Moment
(Envelope)
-53.663 -57.34
-76.195

Bending (Top Edge) ...

M (kN.m) 26.8 6.2 90.7 88.9 11.7 76.0 76.3 7.5 78.8
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.15 0.03 0.50 0.49 0.06 0.42 0.42 0.04 0.44
x (mm) 49.89 49.89 96.02 93.82 49.89 78.92 79.31 49.89 82.07
As (mm2) 144.36 33.49 514.28 502.53 62.84 422.71 424.78 40.55 439.58
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 42.3 76.2 2.3 53.7 5.7 57.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.23 0.42 0.01 0.30 0.03 0.32
x (mm) 49.89 79.15 49.89 54.27 49.89 58.24
As (mm2) 228.05 423.94 12.22 290.70 30.98 311.93
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 87.5 124.3 107.6 101.7 103.8 104.9
v (N/mm2) 0.85 1.20 1.04 0.99 1.01 1.02
vc (N/mm2) 0.50 0.50 0.50 0.50 0.44 0.50 0.50 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.5 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.46 < 39.0 OK 8.69 < 43.66 OK 8.69 < 40.64 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 603.19 603.19 603.19 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16

Top.Sup.

Bot.Bars 3H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-35

Axis: 10 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B96 L=3900mm 1B97 L=3900mm 1B98 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
104.19 103.908 107.156

Shear
Force
(Envelope)
-104.40 -104.731 -101.925
78.763 78.361 78.478 87.671
76.767 76.502

Moment
(Envelope)
-56.54 -57.306 -53.588

Bending (Top Edge) ...

M (kN.m) 78.8 7.7 78.4 78.5 7.4 76.8 76.5 11.2 87.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.44 0.04 0.43 0.43 0.04 0.42 0.42 0.06 0.48
x (mm) 82.08 49.89 81.62 81.75 49.89 79.80 79.50 49.89 92.40
As (mm2) 439.63 41.64 437.17 437.88 40.15 427.42 425.81 60.64 494.93
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 2.7 56.5 2.7 57.3 6.0 53.6 2.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.31 0.01 0.32 0.03 0.30 0.01
x (mm) 49.89 57.37 49.89 58.20 49.89 54.19 49.89
As (mm2) 14.48 307.29 14.53 311.73 32.23 290.27 12.78
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 104.4 104.2 104.7 103.9 101.9 107.2
v (N/mm2) 1.01 1.01 1.01 1.01 0.99 1.04
vc (N/mm2) 0.50 0.44 0.50 0.50 0.44 0.50 0.50 0.44 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 41.28 OK 8.69 < 40.66 OK 8.69 < 43.72 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 3H16 3H16 3H16 3H16 3H16 3H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-36

Axis: 10 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B99 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
89.255

Shear
Force
(Envelope)
-123.209
89.855

29.439
Moment
(Envelope)

-78.104
Bending (Top Edge) ...
M (kN.m) 89.9 5.1 29.4
d (mm) 449.0 449.0 449.0
K/K' 0.50 0.03 0.16
x (mm) 94.98 49.89 49.89
As (mm2) 508.70 27.27 158.74
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 5.5 78.1 41.4
d (mm) 449.0 449.0 449.0
K/K' 0.03 0.43 0.23
x (mm) 49.89 81.33 49.89
As (mm2) 29.77 435.59 223.32
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 123.2 89.3
v (N/mm2) 1.19 0.86
vc (N/mm2) 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.5
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 38.03 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16
Top.Sup. 3H16

Top.Sup.

Bot.Bars 3H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-37

Axis: 11 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B100 L=3900mm 1B101 L=3800mm 1B102 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
75.518 71.954
61.59

Shear
Force
(Envelope) -44.918
-73.055 -72.90

49.736 46.449 53.999 54.321 52.742

22.738
Moment
(Envelope)
-30.131 -35.738 -34.974

Bending (Top Edge) ...

M (kN.m) 22.7 4.1 49.7 46.4 4.5 54.0 54.3 4.3 52.7
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.13 0.02 0.28 0.26 0.02 0.30 0.30 0.02 0.29
x (mm) 49.89 49.89 50.08 49.89 49.89 54.63 54.98 49.89 53.29
As (mm2) 122.61 22.28 268.24 250.46 24.09 292.63 294.49 23.14 285.41
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 22.6 30.1 1.4 3.9 35.7 1.9 1.7 35.0 1.9
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.12 0.17 0.01 0.02 0.20 0.01 0.01 0.19 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 121.66 162.47 7.82 20.88 192.70 10.03 8.97 188.59 9.98
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 44.9 61.6 73.1 75.5 72.9 72.0
v (N/mm2) 0.43 0.60 0.71 0.73 0.71 0.70
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.46 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-38

Axis: 11 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B103 L=3900mm 1B104 L=3900mm 1B105 L=3900mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
72.47 72.438 72.096

Shear
Force
(Envelope)
-72.508 -72.792 -73.721
52.735 52.911 52.973 52.991 53.201 52.312

Moment
(Envelope)
-35.701 -36.001 -36.27

Bending (Top Edge) ...

M (kN.m) 52.7 4.2 52.9 53.0 4.8 53.0 53.2 4.7 52.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.29 0.02 0.29 0.29 0.03 0.29 0.29 0.03 0.29
x (mm) 53.28 49.89 53.47 53.53 49.89 53.55 53.78 49.89 52.83
As (mm2) 285.37 22.86 286.38 286.74 25.82 286.84 288.05 25.21 282.95
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.8 35.7 1.9 1.8 36.0 2.1 1.6 36.3 2.6
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.20 0.01 0.01 0.20 0.01 0.01 0.20 0.01
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 9.79 192.50 10.27 9.96 194.12 11.55 8.67 195.57 14.21
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 72.5 72.5 72.8 72.4 73.7 72.1
v (N/mm2) 0.70 0.70 0.70 0.70 0.71 0.70
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 57.97 OK 8.69 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-39

Axis: 11 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B106 L=3900mm 1B107 L=3900mm
BwxH (mm) 230 x 500 230 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
74.249
61.763

Shear
Force
(Envelope)
-71.922
-84.916
51.669 58.253 61.148

25.263

Moment
(Envelope)
-33.354
-49.303

Bending (Top Edge) ...

M (kN.m) 51.7 7.1 58.3 61.1 1.6 25.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.29 0.04 0.32 0.34 0.01 0.14
x (mm) 52.14 49.89 59.23 62.38 49.89 49.89
As (mm2) 279.27 38.07 317.23 334.12 8.83 136.22
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 1.5 33.4 1.9 1.7 49.3 31.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.01 0.18 0.01 0.01 0.27 0.17
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89
As (mm2) 7.93 179.85 10.11 9.34 265.85 169.39
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 71.9 74.2 84.9 61.8
v (N/mm2) 0.70 0.72 0.82 0.60
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 57.97 OK 8.69 < 47.52 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16
Top.Sup. 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-40

Axis: 12 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B108 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
86.941

Shear
Force
(Envelope)
-87.82

Moment
(Envelope)

-103.305
Bending (Top Edge) ...
M (kN.m) 0.4 0.4
d (mm) 449.0 449.0
K/K' 0.00 0.00
x (mm) 49.89 49.89
As (mm2) 2.18 1.96
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 50.3 103.3 49.6
d (mm) 449.0 449.0 449.0
K/K' 0.28 0.57 0.27
x (mm) 50.70 111.19 49.96
As (mm2) 271.55 595.54 267.62
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 87.8 86.9
v (N/mm2) 0.85 0.84
vc (N/mm2) 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.5
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 21.05 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 3H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-41

Axis: K Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B109 L=2050mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
38.065

Shear
Force
(Envelope)
-38.347

Moment
(Envelope)

-23.19
Bending (Top Edge) ...
M (kN.m) 0.1
d (mm) 449.0
K/K' 0.00
x (mm) 49.89
As (mm2) 0.64
As' (mm2) 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 13.3 23.2 13.5
d (mm) 449.0 449.0 449.0
K/K' 0.07 0.13 0.07
x (mm) 49.89 49.89 49.89
As (mm2) 71.68 125.04 72.70
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 38.3 38.1
v (N/mm2) 0.37 0.37
vc (N/mm2) 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.57 < 44.6 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-42

Axis: L Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B110 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
82.04

Shear
Force
(Envelope)
-82.491

Moment
(Envelope)

-93.685
Bending (Top Edge) ...
M (kN.m) 0.4 0.3
d (mm) 449.0 449.0
K/K' 0.00 0.00
x (mm) 49.89 49.89
As (mm2) 1.90 1.81
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 46.8 93.7 46.4
d (mm) 449.0 449.0 449.0
K/K' 0.26 0.52 0.26
x (mm) 49.89 99.53 49.89
As (mm2) 252.38 533.07 250.19
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 82.5 82.0
v (N/mm2) 0.80 0.79
vc (N/mm2) 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.5
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.69 < 23.87 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 3H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-43

Axis: 13 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B111 L=1670mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
28.346

Shear
Force
(Envelope)
-28.698

Moment
(Envelope)

-14.196
Bending (Top Edge) ...
M (kN.m) 0.1 0.0
d (mm) 449.0 449.0
K/K' 0.00 0.00
x (mm) 49.89 49.89
As (mm2) 0.72 0.00
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 7.8 14.2 7.9
d (mm) 449.0 449.0 449.0
K/K' 0.04 0.08 0.04
x (mm) 49.89 49.89 49.89
As (mm2) 42.08 76.55 42.85
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 28.7 28.3
v (N/mm2) 0.28 0.27
vc (N/mm2) 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 3.72 < 44.6 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-44

Axis: 11 Storey: 1 (/ 2) Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B112 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
109.271

Shear
Force
(Envelope)
-109.27

Moment
(Envelope)

-106.539
Bending (Top Edge) ...
M (kN.m) 0.0
d (mm) 459.0
K/K' 0.00
x (mm) 51.00
As (mm2) 0.00
As' (mm2) 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 59.0 106.5 59.0
d (mm) 459.0 459.0 459.0
K/K' 0.31 0.56 0.31
x (mm) 58.56 111.96 58.56
As (mm2) 313.66 599.68 313.66
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 109.3 109.3
v (N/mm2) 1.04 1.04
vc (N/mm2) 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00
Vnom (kN) 123.5
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.5 < 20.95 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 3H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-45

Axis: J Storey: 1 (/ 2) Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B113 L=3900mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
109.27

Shear
Force
(Envelope)
-109.27

Moment
(Envelope)

-106.539
Bending (Top Edge) ...
M (kN.m) 0.0
d (mm) 459.0
K/K' 0.00
x (mm) 51.00
As (mm2) 0.00
As' (mm2) 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 59.0 106.5 59.0
d (mm) 459.0 459.0 459.0
K/K' 0.31 0.56 0.31
x (mm) 58.56 111.96 58.56
As (mm2) 313.66 599.68 313.66
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 109.3 109.3
v (N/mm2) 1.04 1.04
vc (N/mm2) 0.50 0.50 0.50
v-max (N/mm2) 4.00 4.00
Vnom (kN) 123.5
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.5 < 20.95 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19
Steel Bars ...
Top.Bars 2H16
Top.Sup.

Top.Sup.

Bot.Bars 3H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-46

Axis: J Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B1 L=3900mm 2B2 L=3900mm 2B3 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
38.938 34.257
33.829

Shear
Force
(Envelope)
-30.633 -34.741 -34.032
24.571 24.246 21.91 21.877 22.307

6.627
Moment
(Envelope)
-14.834 -15.448
-20.672

Bending (Top Edge) ...

M (kN.m) 6.6 1.3 24.6 24.2 3.7 21.9 21.9 2.5 22.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.01 0.22 0.22 0.03 0.20 0.20 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 45.97 9.32 170.45 168.20 25.81 151.99 151.76 17.52 154.75
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 10.0 20.7 1.3 0.5 14.8 0.8 1.5 15.4 0.9
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.09 0.19 0.01 0.00 0.14 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 69.72 143.41 8.68 3.71 102.90 5.60 10.45 107.17 5.98
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.6 38.9 34.7 33.8 34.0 34.3
v (N/mm2) 0.38 0.49 0.43 0.42 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-47

Axis: J Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B4 L=3900mm 2B5 L=3900mm 2B6 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.112 34.132 34.66

Shear
Force
(Envelope)
-34.197 -34.161 -33.865
22.329 22.115 22.157 22.085 22.005 24.025

Moment
(Envelope)
-15.354 -15.42 -14.865

Bending (Top Edge) ...

M (kN.m) 22.3 2.6 22.1 22.2 2.5 22.1 22.0 3.7 24.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.02 0.20 0.20 0.02 0.20 0.20 0.03 0.22
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 154.90 18.06 153.42 153.71 17.40 153.20 152.65 25.39 166.67
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.1 15.4 0.9 1.2 15.4 1.0 1.0 14.9 0.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 7.59 106.51 6.56 8.50 106.97 6.81 6.64 103.12 3.82
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.2 34.1 34.2 34.1 33.9 34.7
v (N/mm2) 0.43 0.42 0.43 0.43 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-48

Axis: J Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B7 L=4200mm 2B8 L=1800mm 2B9 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
36.452 35.763

14.146
Shear
Force
(Envelope) -18.751

-38.001 -34.838
25.044 23.509
19.982 16.866
16.648 19.62

12.063
Moment
(Envelope)
-14.97
-18.94

Bending (Top Edge) ...

M (kN.m) 25.0 1.5 20.0 16.9 13.2 16.6 19.6 2.4 23.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.23 0.01 0.18 0.15 0.12 0.15 0.18 0.02 0.22
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 173.73 10.13 138.62 117.00 91.71 115.49 136.10 16.62 163.09
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.0 18.9 3.2 2.2 15.0 1.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.17 0.03 0.02 0.14 0.02
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 13.69 131.39 22.49 15.14 103.85 11.54
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 38.0 36.5 18.8 14.1 34.8 35.8
v (N/mm2) 0.47 0.45 0.23 0.18 0.43 0.45
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 12.03 < 59.44 OK --- 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-49

Axis: J Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B10 L=3900mm
BwxH (mm) 230 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
30.616

Shear
Force
(Envelope)
-38.495
23.862

7.413
Moment
(Envelope)

-19.917

Bending (Top Edge) ...

M (kN.m) 23.9 0.5 7.4
d (mm) 349.0 349.0 349.0
K/K' 0.22 0.00 0.07
x (mm) 38.78 38.78 38.78
As (mm2) 165.53 3.32 51.42
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.5 19.9 9.3
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.18 0.09
x (mm) 38.78 38.78 38.78
As (mm2) 3.19 138.17 64.66
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 38.5 30.6
v (N/mm2) 0.48 0.38
vc (N/mm2) 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00
Vnom (kN) 106.3
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-50

Axis: H Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B20 L=3900mm 2B21 L=3900mm 2B22 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
38.093 34.164 34.071

Shear
Force
(Envelope)
-31.371 -34.185 -34.243
23.19 22.458 22.541 22.449 22.172

8.161
Moment
(Envelope)
-15.08 -15.036
-20.095
Bending (Top Edge) ...
M (kN.m) 8.2 1.0 23.2 22.5 2.7 22.5 22.4 2.4 22.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.07 0.01 0.21 0.21 0.03 0.21 0.21 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 56.61 6.87 160.87 155.79 19.07 156.37 155.73 16.66 153.81
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 8.8 20.1 1.7 0.7 15.1 0.7 0.5 15.0 0.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.08 0.18 0.02 0.01 0.14 0.01 0.00 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 60.89 139.40 11.49 4.93 104.61 5.09 3.58 104.31 5.01
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 31.4 38.1 34.2 34.2 34.2 34.1
v (N/mm2) 0.39 0.47 0.43 0.43 0.43 0.42
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-51

Axis: H Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B23 L=3900mm 2B24 L=3900mm 2B25 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.136 34.245 34.211

Shear
Force
(Envelope)
-34.16 -34.056 -34.174
22.139 22.113 22.072 22.47 22.383 22.651

Moment
(Envelope)
-15.24 -15.129 -15.024

Bending (Top Edge) ...

M (kN.m) 22.1 2.3 22.1 22.1 2.5 22.5 22.4 2.6 22.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.02 0.20 0.20 0.02 0.21 0.20 0.02 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 153.58 16.01 153.40 153.11 17.63 155.88 155.27 18.37 157.13
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.0 15.2 0.8 1.0 15.1 0.6 0.6 15.0 0.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 6.62 105.72 5.60 6.81 104.95 4.20 4.35 104.22 4.81
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.2 34.1 34.1 34.2 34.2 34.2
v (N/mm2) 0.43 0.43 0.42 0.43 0.43 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-52

Axis: H Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B26 L=4200mm 2B27 L=1800mm 2B28 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.929 35.943

12.716
Shear
Force
(Envelope)
-20.755
-36.741 -33.595
23.444 23.796 22.673
20.68
15.649
11.341
10.63
Moment
(Envelope)

-17.245 -16.613

Bending (Top Edge) ...

M (kN.m) 23.4 1.0 23.8 20.7 14.7 11.3 15.6 1.6 22.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.01 0.22 0.19 0.13 0.10 0.14 0.01 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 162.64 7.14 165.08 143.46 102.14 78.67 108.56 11.16 157.29
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.4 17.2 0.2 3.9 16.6 1.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.16 0.00 0.04 0.15 0.02
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 16.99 119.63 1.27 26.76 115.24 12.04
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 36.7 37.9 20.8 12.7 33.6 35.9
v (N/mm2) 0.46 0.47 0.26 0.16 0.42 0.45
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 12.03 < 59.44 OK --- 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-53

Axis: H Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B29 L=3900mm
BwxH (mm) 230 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
31.48

Shear
Force
(Envelope)
-37.87
22.522

8.318
Moment
(Envelope)

-20.117
Bending (Top Edge) ...
M (kN.m) 22.5 0.5 8.3
d (mm) 349.0 349.0 349.0
K/K' 0.21 0.00 0.08
x (mm) 38.78 38.78 38.78
As (mm2) 156.24 3.45 57.71
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.6 20.1 8.7
d (mm) 349.0 349.0 349.0
K/K' 0.02 0.18 0.08
x (mm) 38.78 38.78 38.78
As (mm2) 17.75 139.56 60.28
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 37.9 31.5
v (N/mm2) 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00
Vnom (kN) 106.3
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-54

Axis: G Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B30 L=3900mm 2B31 L=3900mm 2B32 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
38.741 33.959 34.165

Shear
Force
(Envelope)
-30.831 -34.528 -34.13

24.475 23.615 22.11 22.142 22.19

7.079
Moment
(Envelope)
-14.936 -15.404
-20.316

Bending (Top Edge) ...

M (kN.m) 7.1 1.4 24.5 23.6 3.3 22.1 22.1 2.6 22.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.01 0.22 0.22 0.03 0.20 0.20 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 49.11 9.50 169.79 163.82 23.22 153.38 153.60 17.98 153.94
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 9.5 20.3 1.2 0.5 14.9 0.8 1.3 15.4 0.9
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.09 0.19 0.01 0.01 0.14 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 65.97 140.93 8.30 3.79 103.62 5.24 8.68 106.86 6.48
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.8 38.7 34.5 34.0 34.1 34.2
v (N/mm2) 0.38 0.48 0.43 0.42 0.43 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-55

Axis: G Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B33 L=3900mm 2B34 L=3900mm 2B35 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.167 34.039 35.502

Shear
Force
(Envelope)
-34.124 -34.268 -33.315
26.74
22.141 22.237 22.228 21.737 21.437

Moment
(Envelope) 0.105

-15.391 -15.551 -14.188

Bending (Top Edge) ...

M (kN.m) 22.1 2.6 22.2 22.2 2.5 21.7 21.4 5.2 26.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.02 0.20 0.20 0.02 0.20 0.20 0.05 0.24
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 153.59 17.75 154.26 154.20 17.26 150.79 148.71 36.34 185.50
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 15.4 0.9 1.2 15.6 1.4 1.0 14.2 0.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.01 0.01 0.13 0.00
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.61 106.77 6.46 8.64 107.88 9.61 6.89 98.43 3.36
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.1 34.2 34.3 34.0 33.3 35.5
v (N/mm2) 0.43 0.43 0.43 0.42 0.42 0.44
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-56

Axis: G Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B36 L=4200mm
BwxH (mm) 230 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
33.117

Shear
Force
(Envelope)
-41.848
28.676

8.051
Moment
(Envelope)

-23.241

Bending (Top Edge) ...

M (kN.m) 28.7 1.5 8.1
d (mm) 349.0 349.0 349.0
K/K' 0.26 0.01 0.07
x (mm) 38.78 38.78 38.78
As (mm2) 198.93 10.57 55.85
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.9 23.2 10.7
d (mm) 349.0 349.0 349.0
K/K' 0.01 0.21 0.10
x (mm) 38.78 38.78 38.78
As (mm2) 6.57 161.23 74.37
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 41.8 33.1
v (N/mm2) 0.52 0.41
vc (N/mm2) 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00
Vnom (kN) 106.3
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 12.03 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-57

Axis: F Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B37 L=1800mm 2B38 L=3900mm 2B39 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.779
31.24
15.747

Shear
Force
(Envelope) -16.04
-31.705
-38.215
24.407 23.793

10.227 8.24
5.479 4.776
Moment
(Envelope) 0.527
-4.29

-18.655 -19.818

Bending (Top Edge) ...

M (kN.m) 5.5 1.2 4.8 10.2 1.6 24.4 23.8 1.1 8.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.01 0.04 0.09 0.01 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 38.01 8.33 33.13 70.94 11.32 169.31 165.05 7.58 57.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.1 4.3 1.5 7.2 18.7 1.1 1.6 19.8 8.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.07 0.17 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 7.31 29.76 10.68 49.88 129.41 7.31 11.15 137.48 59.78
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 16.0 15.7 31.7 37.8 38.2 31.2
v (N/mm2) 0.20 0.20 0.39 0.47 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-58

Axis: E Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B40 L=1800mm 2B41 L=3900mm 2B42 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.311
31.203
17.30

Shear
Force
(Envelope) -15.477
-32.224
-38.167
24.092 23.597

11.736
6.76 8.264
4.783
Moment
(Envelope) 0.878
-4.028

-17.903 -19.89

Bending (Top Edge) ...

M (kN.m) 4.8 2.6 6.8 11.7 1.6 24.1 23.6 1.0 8.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.02 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.18 18.16 46.89 81.42 11.42 167.13 163.69 6.63 57.33
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.0 1.0 5.9 17.9 1.0 1.6 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.05 0.16 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.60 27.95 6.88 40.75 124.19 7.16 11.24 137.98 60.35
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.5 17.3 32.2 37.3 38.2 31.2
v (N/mm2) 0.19 0.22 0.40 0.46 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-59

Axis: D Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B43 L=1800mm 2B44 L=3900mm 2B45 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.377
31.18
17.122

Shear
Force
(Envelope) -15.566
-32.137
-38.185
24.16 23.651

11.545
6.525 8.261
4.875
Moment
(Envelope) 0.825
-4.049

-17.993 -19.89

Bending (Top Edge) ...

M (kN.m) 4.9 2.4 6.5 11.5 1.6 24.2 23.7 1.0 8.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.02 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.82 16.93 45.27 80.09 11.43 167.60 164.07 6.78 57.31
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.0 1.0 6.0 18.0 1.0 1.6 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.45 28.09 7.20 41.82 124.82 6.86 11.00 137.98 60.47
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.6 17.1 32.1 37.4 38.2 31.2
v (N/mm2) 0.19 0.21 0.40 0.47 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-60

Axis: C Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B46 L=1800mm 2B47 L=3900mm 2B48 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.069
31.369
17.455

Shear
Force
(Envelope) -15.252
-32.361
-37.961
23.511 23.103

12.096
7.049 8.514
4.789
Moment
(Envelope) 0.93
-3.831

-17.975 -19.936
Bending (Top Edge) ...
M (kN.m) 4.8 2.7 7.0 12.1 1.4 23.5 23.1 0.8 8.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.01 0.22 0.21 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.23 18.87 48.90 83.91 9.98 163.10 160.27 5.65 59.06
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 3.8 0.7 6.0 18.0 1.4 2.0 19.9 8.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.02 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.24 26.58 4.95 41.88 124.70 9.45 13.65 138.30 59.35
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.3 17.5 32.4 37.1 38.0 31.4
v (N/mm2) 0.19 0.22 0.40 0.46 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-61

Axis: B Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B49 L=1800mm 2B50 L=3900mm 2B51 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
39.516
30.284
14.917
Shear
Force
(Envelope) -17.753
-30.548
-39.48
28.724 26.911

8.92 6.731
4.934 4.263
Moment
(Envelope) -5.881
-17.729 -19.771

Bending (Top Edge) ...

M (kN.m) 4.9 1.0 4.3 8.9 2.9 28.7 26.9 2.4 6.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.01 0.04 0.08 0.03 0.26 0.25 0.02 0.06
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 34.23 6.63 29.57 61.88 20.30 199.26 186.68 16.37 46.70
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.7 5.9 3.9 8.1 17.7 0.3 0.5 19.8 9.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.05 0.04 0.07 0.16 0.00 0.00 0.18 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 11.53 40.80 27.39 56.26 122.99 2.35 3.63 137.15 66.20
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 17.8 14.9 30.5 39.5 39.5 30.3
v (N/mm2) 0.22 0.19 0.38 0.49 0.49 0.38
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-62

Axis: A Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B52 L=1800mm 2B53 L=3900mm 2B54 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
39.06
29.737
17.017

Shear
Force
(Envelope) -16.985
-31.592
-39.796
28.716 27.276

11.642
7.879 5.931
4.032
Moment
(Envelope) 0.70
-5.686
-16.815 -19.928

Bending (Top Edge) ...

M (kN.m) 4.0 3.3 7.9 11.6 3.6 28.7 27.3 2.1 5.9
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.03 0.07 0.11 0.03 0.26 0.25 0.02 0.05
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 27.97 22.88 54.66 80.76 24.77 199.20 189.21 14.36 41.14
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.9 5.7 3.3 6.7 16.8 0.5 0.4 19.9 10.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.05 0.03 0.06 0.15 0.00 0.00 0.18 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 13.44 39.44 23.02 46.68 116.65 3.53 2.49 138.24 70.69
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 17.0 17.0 31.6 39.1 39.8 29.7
v (N/mm2) 0.21 0.21 0.39 0.49 0.50 0.37
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-63

Axis: 1 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B57 L=1800mm 2B56 L=3900mm 2B55 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
40.948 42.754
16.338
Shear
Force
(Envelope) -17.735
-30.846
-55.642
34.593 34.777

4.04 7.496 11.10 7.57

Moment
(Envelope) 0.557
-6.465
-16.064
-29.389
Bending (Top Edge) ...
M (kN.m) 4.0 3.0 7.5 11.1 7.5 34.6 34.8 1.2 7.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.03 0.07 0.10 0.07 0.32 0.32 0.01 0.07
x (mm) 38.78 38.78 38.78 38.78 38.78 45.20 45.45 38.78 38.78
As (mm2) 28.03 20.88 52.00 77.00 52.07 242.09 243.45 8.52 52.51
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.3 6.5 4.7 6.5 16.1 0.5 29.4 15.1
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.06 0.04 0.06 0.15 0.00 0.27 0.14
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 15.63 44.85 32.81 45.22 111.44 3.57 203.87 104.45
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 17.7 16.3 30.8 40.9 55.6 42.8
v (N/mm2) 0.22 0.20 0.38 0.51 0.69 0.53
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 55.48 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-64

Axis: 2 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B60 L=1800mm 2B59 L=3900mm 2B58 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
39.699
30.124
14.809
Shear
Force
(Envelope) -17.987
-30.488
-39.643
29.101 27.396

8.817 6.629
4.927 4.256
Moment
(Envelope) -6.117
-17.726 -19.647

Bending (Top Edge) ...

M (kN.m) 4.9 0.9 4.3 8.8 3.1 29.1 27.4 2.5 6.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.01 0.04 0.08 0.03 0.27 0.25 0.02 0.06
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 34.18 6.52 29.52 61.17 21.30 201.87 190.05 17.09 45.99
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.7 6.1 4.3 8.3 17.7 0.3 0.5 19.6 9.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.06 0.04 0.08 0.16 0.00 0.00 0.18 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 12.11 42.43 29.87 57.51 122.97 2.35 3.48 136.29 66.50
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 18.0 14.8 30.5 39.7 39.6 30.1
v (N/mm2) 0.22 0.18 0.38 0.49 0.49 0.38
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-65

Axis: 3 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B63 L=1800mm 2B62 L=3900mm 2B61 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.201
31.311
17.299

Shear
Force
(Envelope) -15.462
-32.301
-38.02
23.758 23.206

11.831
6.793 8.427
4.829
Moment
(Envelope) 0.892
-3.976

-18.006 -19.967

Bending (Top Edge) ...

M (kN.m) 4.8 2.6 6.8 11.8 1.5 23.8 23.2 0.8 8.4
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.01 0.22 0.21 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.50 18.22 47.12 82.08 10.57 164.81 160.98 5.68 58.46
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.0 0.9 6.3 18.0 1.3 1.9 20.0 8.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.02 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.45 27.58 6.47 44.00 124.91 8.93 13.27 138.51 59.95
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.5 17.3 32.3 37.2 38.0 31.3
v (N/mm2) 0.19 0.22 0.40 0.46 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-66

Axis: 4 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B66 L=1800mm 2B65 L=3900mm 2B64 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.369
31.173
17.147

Shear
Force
(Envelope) -15.568
-32.142
-38.185
24.154 23.649

11.572
6.559 8.272
4.877
Moment
(Envelope) 0.823
-4.041

-17.981 -19.894

Bending (Top Edge) ...

M (kN.m) 4.9 2.5 6.6 11.6 1.6 24.2 23.6 1.0 8.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.02 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.83 17.11 45.50 80.28 11.43 167.56 164.06 6.74 57.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.0 1.0 6.0 18.0 1.0 1.6 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.41 28.03 7.19 41.70 124.74 6.83 10.95 138.01 60.55
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.6 17.1 32.1 37.4 38.2 31.2
v (N/mm2) 0.19 0.21 0.40 0.47 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-67

Axis: 5 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B69 L=1800mm 2B68 L=3900mm 2B67 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.343
31.179
17.148

Shear
Force
(Envelope) -15.57
-32.167
-38.181
24.103 23.626

11.621
6.578 8.268
4.892
Moment
(Envelope) 0.841
-4.03

-17.975 -19.904

Bending (Top Edge) ...

M (kN.m) 4.9 2.5 6.6 11.6 1.6 24.1 23.6 1.0 8.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.06 0.11 0.01 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 33.94 17.27 45.63 80.62 11.33 167.21 163.90 6.68 57.36
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.0 1.0 6.0 18.0 1.0 1.6 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.05 0.16 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.34 27.95 7.13 41.45 124.69 7.07 11.12 138.07 60.58
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.6 17.1 32.2 37.3 38.2 31.2
v (N/mm2) 0.19 0.21 0.40 0.47 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-68

Axis: 6 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B72 L=1800mm 2B71 L=3900mm 2B70 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.393
31.184
17.028

Shear
Force
(Envelope) -15.648
-32.137
-38.196
24.16 23.674

11.484
6.415 8.244
4.918
Moment
(Envelope) 0.833
-4.086

-18.001 -19.885

Bending (Top Edge) ...

M (kN.m) 4.9 2.4 6.4 11.5 1.6 24.2 23.7 1.0 8.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.02 0.06 0.11 0.02 0.22 0.22 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 34.11 16.73 44.50 79.67 11.38 167.60 164.23 6.86 57.19
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.2 4.1 1.1 6.1 18.0 1.0 1.6 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.01 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.37 28.34 7.73 42.13 124.88 6.94 10.99 137.94 60.48
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.6 17.0 32.1 37.4 38.2 31.2
v (N/mm2) 0.19 0.21 0.40 0.47 0.48 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-69

Axis: 7 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B75 L=1800mm 2B74 L=3900mm 2B73 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.163
31.294
17.586

Shear
Force
(Envelope) -15.011
-32.308
-38.101
23.877 23.394

12.098
7.172 8.278
4.671
Moment
(Envelope) 0.954
-3.867

-17.901 -19.933

Bending (Top Edge) ...

M (kN.m) 4.7 2.7 7.2 12.1 1.6 23.9 23.4 0.9 8.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.02 0.07 0.11 0.01 0.22 0.21 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 32.41 18.66 49.75 83.92 11.25 165.64 162.28 6.31 57.42
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.3 3.9 0.6 6.2 17.9 1.2 1.8 19.9 8.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.04 0.01 0.06 0.16 0.01 0.02 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 8.99 26.83 3.98 43.10 124.18 8.09 12.68 138.27 60.03
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 15.0 17.6 32.3 37.2 38.1 31.3
v (N/mm2) 0.19 0.22 0.40 0.46 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-70

Axis: 8 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B76 L=3900mm 2B77 L=3800mm 2B78 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
38.621 34.319
33.069

Shear
Force
(Envelope)
-30.852 -33.637 -34.028
24.00 22.862 21.423 21.604 22.294

7.014
Moment
(Envelope)
-14.041 -15.477
-20.42

Bending (Top Edge) ...

M (kN.m) 7.0 1.1 24.0 22.9 3.7 21.4 21.6 2.4 22.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.01 0.22 0.21 0.03 0.20 0.20 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 48.66 7.67 166.49 158.60 25.57 148.61 149.87 16.93 154.66
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 9.6 20.4 1.3 0.5 14.0 0.7 1.3 15.5 0.9
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.09 0.19 0.01 0.00 0.13 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 66.29 141.65 8.91 3.76 97.40 4.80 9.15 107.36 6.24
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.9 38.6 33.6 33.1 34.0 34.3
v (N/mm2) 0.38 0.48 0.42 0.41 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 10.89 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-71

Axis: 8 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B79 L=3900mm 2B80 L=3900mm 2B81 L=2100mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.302 34.074
18.039

Shear
Force
(Envelope)
-21.018
-34.03 -35.40
22.134 22.571 22.674
17.769 15.628
9.752

Moment 5.154
(Envelope) -0.655

-15.114 -15.654

Bending (Top Edge) ...

M (kN.m) 22.1 2.5 22.6 22.7 1.9 17.8 15.6 8.7 9.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.02 0.21 0.21 0.02 0.16 0.14 0.08 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 153.55 17.35 156.58 157.29 13.37 123.26 108.41 60.42 67.65
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.1 15.1 0.6 1.3 15.7 1.7 0.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.02 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 7.56 104.85 3.87 8.81 108.59 11.84 4.55
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.0 34.3 35.4 34.1 21.0 18.0
v (N/mm2) 0.42 0.43 0.44 0.42 0.26 0.22
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 6.02 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-72

Axis: 8 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B82 L=1800mm 2B83 L=3900mm 2B84 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.418
30.409
13.779
Shear
Force
(Envelope) -18.642
-32.926
-38.872
24.684 24.513

11.492 13.465
9.505 7.036
Moment 6.171
(Envelope) -1.836

-17.373
-20.434

Bending (Top Edge) ...

M (kN.m) 11.5 6.9 9.5 13.5 2.4 24.7 24.5 1.0 7.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.11 0.06 0.09 0.12 0.02 0.23 0.22 0.01 0.06
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 79.72 47.69 65.94 93.41 16.56 171.24 170.05 6.81 48.81
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.8 0.1 5.5 17.4 1.7 0.9 20.4 10.1
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.00 0.05 0.16 0.02 0.01 0.19 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 12.74 1.01 38.28 120.52 11.88 6.12 141.75 69.93
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 18.6 13.8 32.9 37.4 38.9 30.4
v (N/mm2) 0.23 0.17 0.41 0.47 0.48 0.38
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 5.16 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-73

Axis: 9 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B85 L=3900mm 2B86 L=3800mm 2B87 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.92 33.373 34.163

Shear
Force
(Envelope)
-31.431 -33.242 -34.24
22.736 21.515 21.953 22.094 22.176

8.298
Moment
(Envelope)
-14.217 -15.09
-20.065
Bending (Top Edge) ...
M (kN.m) 8.3 0.7 22.7 21.5 3.2 22.0 22.1 2.3 22.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.08 0.01 0.21 0.20 0.03 0.20 0.20 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 57.56 5.19 157.72 149.25 21.96 152.29 153.27 15.81 153.83
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 8.7 20.1 1.7 0.7 14.2 0.6 0.6 15.1 0.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.08 0.18 0.02 0.01 0.13 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 60.05 139.19 11.57 5.01 98.63 4.38 4.02 104.68 5.26
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 31.4 37.9 33.2 33.4 34.2 34.2
v (N/mm2) 0.39 0.47 0.41 0.42 0.43 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 10.89 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-74

Axis: 9 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B88 L=3900mm 2B89 L=3900mm 2B90 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.199 34.254 34.963

Shear
Force
(Envelope)
-34.107 -34.241 -33.727
22.06 22.282 22.20 21.815 21.591 23.21

Moment
(Envelope)
-15.161 -15.084 -14.886

Bending (Top Edge) ...

M (kN.m) 22.1 2.4 22.3 22.2 2.2 21.8 21.6 2.5 23.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.02 0.20 0.20 0.02 0.20 0.20 0.02 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 153.03 16.31 154.57 154.00 15.36 151.33 149.78 17.49 161.01
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.9 15.2 0.7 1.0 15.1 0.4 2.0 14.9 0.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.00 0.02 0.14 0.00
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 6.53 105.18 4.67 6.70 104.64 3.03 13.75 103.27 1.67
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.1 34.2 34.2 34.3 33.7 35.0
v (N/mm2) 0.42 0.43 0.43 0.43 0.42 0.44
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-75

Axis: 9 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B91 L=3900mm 2B92 L=3900mm
BwxH (mm) 230 x 400 230 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.383 31.759

Shear
Force
(Envelope)
-34.373 -37.936
23.021 22.12 22.929

8.59
Moment
(Envelope)
-15.088
-20.202
Bending (Top Edge) ...
M (kN.m) 23.0 3.4 22.1 22.9 1.2 8.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.03 0.20 0.21 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 159.70 23.52 153.45 159.06 8.25 59.59
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.3 15.1 0.3 3.2 20.2 8.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.00 0.03 0.18 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 9.12 104.67 2.29 22.29 140.14 59.01
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.4 34.4 37.9 31.8
v (N/mm2) 0.43 0.43 0.47 0.40
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16
Top.Sup. 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-76

Axis: 11 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B100 L=3900mm 2B101 L=3800mm 2B102 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
38.649 34.448
32.946

Shear
Force
(Envelope)
-30.809 -33.806 -33.943
23.66 23.278 21.196 21.281 22.474

6.844
Moment
(Envelope)
-13.99 -15.535
-20.831
Bending (Top Edge) ...
M (kN.m) 6.8 1.0 23.7 23.3 3.9 21.2 21.3 2.5 22.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.01 0.22 0.21 0.04 0.19 0.19 0.02 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 47.48 6.82 164.13 161.48 27.00 147.04 147.63 17.13 155.90
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 10.0 20.8 1.6 0.5 14.0 0.8 1.5 15.5 0.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.09 0.19 0.01 0.00 0.13 0.01 0.01 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 69.61 144.51 10.92 3.67 97.05 5.34 10.63 107.77 5.85
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.8 38.6 33.8 32.9 33.9 34.4
v (N/mm2) 0.38 0.48 0.42 0.41 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 10.89 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-77

Axis: 11 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B103 L=3900mm 2B104 L=3900mm 2B105 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.056 34.14 34.14

Shear
Force
(Envelope)
-34.253 -34.383 -34.781
22.459 22.121 22.164 22.155 22.20 22.193

Moment
(Envelope)
-15.339 -15.698 -15.517

Bending (Top Edge) ...

M (kN.m) 22.5 2.7 22.1 22.2 3.0 22.2 22.2 3.3 22.2
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.02 0.20 0.20 0.03 0.20 0.20 0.03 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 155.80 18.41 153.46 153.75 20.97 153.69 154.00 23.08 153.95
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.9 15.3 1.0 1.2 15.7 1.6 0.3 15.5 1.9
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.01 0.01 0.14 0.01 0.00 0.14 0.02
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 6.54 106.41 7.21 8.34 108.90 10.96 2.40 107.64 13.46
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.3 34.1 34.4 34.1 34.8 34.1
v (N/mm2) 0.43 0.42 0.43 0.43 0.43 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-78

Axis: 11 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B106 L=3900mm 2B107 L=3900mm
BwxH (mm) 230 x 400 230 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.44 30.666

Shear
Force
(Envelope)
-34.556 -38.592
22.181 23.344 24.18

7.416
Moment
(Envelope)
-14.823
-20.049

Bending (Top Edge) ...

M (kN.m) 22.2 3.5 23.3 24.2 0.9 7.4
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.20 0.03 0.21 0.22 0.01 0.07
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 153.88 24.23 161.94 167.74 6.33 51.44
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.3 14.8 1.1 0.8 20.0 9.4
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.00 0.14 0.01 0.01 0.18 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 1.85 102.83 7.62 5.74 139.09 65.13
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.6 34.4 38.6 30.7
v (N/mm2) 0.43 0.43 0.48 0.38
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16
Top.Sup. 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-79

Axis: I Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B108 L=3900mm 2B109 L=3900mm 2B110 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
39.535 35.271
31.995

Shear
Force
(Envelope)
-30.408 -33.34
-36.535
25.053 28.365 23.309
19.033 18.908

4.987
Moment
(Envelope) 0.295

-15.063 -16.886
-22.09

Bending (Top Edge) ...

M (kN.m) 5.0 2.0 25.1 28.4 5.9 19.0 18.9 3.2 23.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.02 0.23 0.26 0.05 0.17 0.17 0.03 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 34.59 13.95 173.79 196.77 40.85 132.04 131.17 22.45 161.70
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 11.6 22.1 2.4 0.5 15.1 4.1 5.0 16.9 1.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.11 0.20 0.02 0.00 0.14 0.04 0.05 0.15 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 80.72 153.24 16.80 3.32 104.50 28.54 34.77 117.14 10.55
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.4 39.5 36.5 32.0 33.3 35.3
v (N/mm2) 0.38 0.49 0.46 0.40 0.42 0.44
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-80

Axis: I Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B111 L=3900mm 2B112 L=3900mm 2B113 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
33.816 34.303 34.386

Shear
Force
(Envelope)
-34.518 -33.989 -33.899

23.249 21.785 21.832 22.43 22.332 23.282

Moment
(Envelope)
-15.849 -16.145 -15.582

Bending (Top Edge) ...

M (kN.m) 23.2 3.8 21.8 21.8 3.3 22.4 22.3 3.7 23.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.03 0.20 0.20 0.03 0.21 0.20 0.03 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 161.28 26.31 151.12 151.45 23.18 155.60 154.92 25.41 161.51
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.4 15.8 1.9 2.6 16.1 1.6 2.0 15.6 1.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.15 0.02 0.02 0.15 0.01 0.02 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 9.51 109.94 12.94 18.31 112.00 10.97 13.60 108.09 7.11
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.5 33.8 34.0 34.3 33.9 34.4
v (N/mm2) 0.43 0.42 0.42 0.43 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-81

Axis: I Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B114 L=4200mm 2B115 L=1800mm 2B116 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
37.424 34.951

15.645

Shear
Force
(Envelope) -16.038

-37.763 -34.952
24.446 21.96
21.009 17.423
16.032 18.953
13.142
Moment
(Envelope)
-18.92 -15.909

Bending (Top Edge) ...

M (kN.m) 24.4 1.8 21.0 17.4 14.1 16.0 19.0 2.2 22.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.22 0.02 0.19 0.16 0.13 0.15 0.17 0.02 0.20
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 169.59 12.40 145.74 120.86 97.94 111.21 131.48 15.37 152.34
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 3.8 18.9 2.4 1.1 15.9 3.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.17 0.02 0.01 0.15 0.03
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 26.55 131.25 16.56 7.94 110.36 20.69
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 37.8 37.4 16.0 15.6 35.0 35.0
v (N/mm2) 0.47 0.47 0.20 0.19 0.44 0.44
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 12.03 < 59.44 OK --- 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-82

Axis: I Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B117 L=3900mm
BwxH (mm) 230 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
31.385

Shear
Force
(Envelope)
-37.734
22.018
8.455
Moment
(Envelope)

-21.241

Bending (Top Edge) ...

M (kN.m) 22.0 0.7 8.5
d (mm) 349.0 349.0 349.0
K/K' 0.20 0.01 0.08
x (mm) 38.78 38.78 38.78
As (mm2) 152.74 5.10 58.65
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 3.8 21.2 9.8
d (mm) 349.0 349.0 349.0
K/K' 0.04 0.19 0.09
x (mm) 38.78 38.78 38.78
As (mm2) 26.65 147.35 67.90
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 37.7 31.4
v (N/mm2) 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00
Vnom (kN) 106.3
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16
Top.Sup. 2H16

Top.Sup.

Bot.Bars 2H16
Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-83

Axis: 10 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B125 L=3900mm 2B124 L=3800mm 2B123 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
39.214 35.387
31.128

Shear
Force
(Envelope)
-30.626 -33.341
-35.517
24.048 27.094 23.381
18.51 18.525

5.232
Moment
(Envelope) 0.72

-14.247 -16.895
-22.267

Bending (Top Edge) ...

M (kN.m) 5.2 1.7 24.0 27.1 5.9 18.5 18.5 3.1 23.4
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.02 0.22 0.25 0.05 0.17 0.17 0.03 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 36.29 11.56 166.82 187.95 40.85 128.41 128.51 21.78 162.19
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 11.6 22.3 2.8 0.5 14.2 4.0 5.1 16.9 1.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.11 0.20 0.03 0.00 0.13 0.04 0.05 0.15 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 80.32 154.47 19.36 3.21 98.83 28.03 35.34 117.20 10.61
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 30.6 39.2 35.5 31.1 33.3 35.4
v (N/mm2) 0.38 0.49 0.44 0.39 0.42 0.44
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 10.89 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-84

Axis: 10 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B122 L=3900mm 2B121 L=3900mm 2B120 L=3900mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
33.836 34.163 34.296

Shear
Force
(Envelope)
-34.478 -34.138 -34.005
23.266 21.956 22.012 22.03 22.021 22.621

Moment
(Envelope)
-15.768 -16.263 -16.005

Bending (Top Edge) ...

M (kN.m) 23.3 3.8 22.0 22.0 3.2 22.0 22.0 3.5 22.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.03 0.20 0.20 0.03 0.20 0.20 0.03 0.21
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 161.40 26.23 152.31 152.70 22.06 152.82 152.76 24.49 156.92
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 1.3 15.8 1.8 2.5 16.3 1.8 2.4 16.0 1.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.01 0.14 0.02 0.02 0.15 0.02 0.02 0.15 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 9.03 109.38 12.36 17.64 112.82 12.63 16.36 111.03 10.28
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.5 33.8 34.1 34.2 34.0 34.3
v (N/mm2) 0.43 0.42 0.43 0.43 0.42 0.43
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16 2H16
Top.Sup. 2H16 2H16 2H16 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-85

Axis: 10 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B119 L=3900mm 2B118 L=3900mm
BwxH (mm) 230 x 400 230 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
34.059 31.495

Shear
Force
(Envelope)
-34.263 -37.87
22.591 22.12 22.888

8.795
Moment
(Envelope)
-16.037
-21.193

Bending (Top Edge) ...

M (kN.m) 22.6 3.5 22.1 22.9 1.6 8.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.03 0.20 0.21 0.01 0.08
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 156.72 24.62 153.45 158.78 11.22 61.01
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.1 16.0 1.9 4.1 21.2 10.0
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.15 0.02 0.04 0.19 0.09
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 14.33 111.25 13.18 28.20 147.02 69.55
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 34.3 34.1 37.9 31.5
v (N/mm2) 0.43 0.42 0.47 0.39
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 11.17 < 59.44 OK 11.17 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12
Steel Bars ...
Top.Bars 2H16 2H16
Top.Sup. 2H16 2H16 2H16

Top.Sup.

Bot.Bars 2H16 2H16

Bot.Bars
Bot.Sup.

Side Bar

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy (0001907)
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-86

Project: JNHPPAdministrationBuilding150mmslabrevB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-1

Axis: G Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B1 L=6000mm 1B2 L=6000mm 1B3 L=6000mm
BwxH (mm) 300 x 500 300 x 500 300 x 650
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
182.72 174.459 170.027

Shear
Force
(Envelope)
-137.451 -129.474
-180.738
224.118 215.738 215.382
179.085 163.012
85.151
Moment
(Envelope)
-77.564
-147.279 -133.205

Bending (Top Edge) ...

M (kN.m) 85.2 11.0 224.1 215.7 11.4 179.1 163.0 39.1 215.4
d (mm) 449.0 449.0 428.0 428.0 449.0 447.0 597.0 599.0 597.0
K/K' 0.36 0.05 1.05 1.01 0.05 0.77 0.39 0.09 0.52
x (mm) 66.92 49.89 212.20 212.20 49.89 156.58 96.98 66.56 131.88
As (mm2) 467.55 59.31 1542.58 1491.18 61.28 1093.90 677.55 158.23 921.37
As' (mm2) 0.00 0.00 60.06 8.67 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 195.00 195.00 195.00 195.00 253.50 253.50 253.50
Bending (Bottom Edge) ...
M (kN.m) 57.1 147.3 2.5 3.0 133.2 6.2 8.8 77.6
d (mm) 447.0 447.0 447.0 447.0 447.0 447.0 599.0 599.0
K/K' 0.24 0.63 0.01 0.01 0.57 0.03 0.02 0.18
x (mm) 49.67 123.93 49.67 49.67 110.37 49.67 66.56 66.56
As (mm2) 309.44 865.84 13.33 16.06 771.07 33.55 35.53 313.50
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 300.00 300.00 195.00 195.00 253.50 253.50 253.50
Shear and Bending Design ...
Vd (kN) 137.5 182.7 180.7 174.5 129.5 170.0
v (N/mm2) 1.02 1.42 1.41 1.30 0.72 0.95
vc (N/mm2) 0.46 0.53 0.64 0.64 0.53 0.59 0.50 0.39 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 142.3 142.3 161.7
Td (kN.m) 0.1 0.1 1.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 1600.0 1600.0 1600.0 0.0 0.0
Links H8-300 H8-300 H8-200 H8-200 H8-300 H8-200 H8-300 H8-300 H8-300
Deflection Check ...
L/d 13.42 < 28.62 OK 13.42 < 31.06 OK 10.02 < 55.61 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 603.19 1658.76 1658.76 402.12 1256.64 1256.64 402.12 1256.64
Bot Edge 942.48 942.48 942.48 942.48 942.48 942.48 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-2

Axis: G Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B4 L=6000mm
BwxH (mm) 300 x 650
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)

133.859

Shear
Force
(Envelope)
-234.248
230.875

81.058
Moment
(Envelope)

-174.691

Bending (Top Edge) ...

M (kN.m) 230.9 81.1
d (mm) 597.0 599.0
K/K' 0.55 0.19
x (mm) 142.66 66.56
As (mm2) 996.64 327.62
As' (mm2) 0.00 0.00
As-min 253.50 253.50 253.50
Bending (Bottom Edge) ...
M (kN.m) 12.9 174.7 75.4
d (mm) 597.0 597.0 597.0
K/K' 0.03 0.42 0.18
x (mm) 66.33 104.58 66.33
As (mm2) 52.51 730.61 305.95
As' (mm2) 0.00 0.00 0.00
As-min 253.50 253.50 253.50
Shear and Bending Des ign ...
Vd (kN) 234.2 133.9
v (N/mm2) 1.31 0.74
vc (N/mm2) 0.50 0.45 0.34
v-max (N/mm2) 4.00 4.00
Vnom (kN) 173.3
Td (kN.m) 0.9
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1575.0 0.0
Links H8-175 H8-300 H8-300
Deflection Check ...
L/d 10.05 < 35.29 OK
Supplied Steel Areas (mm2)
Top Edge 1256.64 402.12 402.12
Bot Edge 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-3

Axis: F Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B5 L=6000mm 1B6 L=6000mm
BwxH (mm) 300 x 500 300 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
273.885
228.009

Shear
Force
(Envelope)
-197.62
-299.692
366.108 374.893

108.25 131.972
Moment
(Envelope)
-223.192 -260.485

Bending (Top Edge) ...

M (kN.m) 108.2 44.0 366.1 374.9 22.0 132.0
d (mm) 447.0 447.0 427.0 427.0 447.0 447.0
K/K' 0.46 0.19 1.72 1.76 0.09 0.56
x (mm) 87.42 49.67 211.71 211.71 49.67 109.20
As (mm2) 610.74 238.07 2418.63 2472.65 118.91 762.92
As' (mm2) 0.00 0.00 939.58 993.60 0.00 0.00
As-min 195.00 300.00 195.00 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 80.9 223.2 9.8 3.5 260.5 90.4
d (mm) 447.0 428.0 447.0 447.0 428.0 447.0
K/K' 0.35 1.04 0.04 0.02 1.22 0.39
x (mm) 63.67 212.20 49.67 49.67 212.20 71.77
As (mm2) 444.81 1536.90 52.84 19.22 1765.63 501.37
As' (mm2) 0.00 54.38 0.00 0.00 283.11 0.00
As-min 195.00 195.00 300.00 300.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 197.6 273.9 299.7 228.0
v (N/mm2) 1.47 2.14 2.34 1.70
vc (N/mm2) 0.53 0.64 0.74 0.74 0.67 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 180.3 183.8
Td (kN.m) 0.0 0.1
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 1500.0 1600.0 1700.0 1500.0
Links H8-150 H8-225 H8-100 H8-100 H8-225 H8-125
Deflection Check ...
L/d 14.02 < 25.9 OK 14.02 < 24.49 OK
Supplied Steel Areas (mm2)
Top Edge 942.48 942.48 2513.27 2513.27 942.48 942.48
Bot Edge 1256.64 1658.76 1256.64 1256.64 1859.82 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-4

Axis: E Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B7 L=6000mm 1B8 L=6000mm 1B9 L=6000mm
BwxH (mm) 300 x 500 300 x 500 300 x 650
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
244.992 222.638 196.201

Shear
Force
(Envelope)
-186.696 -176.861
-228.676
297.903 278.956
238.885 225.097 243.107
103.082
Moment
(Envelope)
-168.485 -143.063
-204.746

Bending (Top Edge) ...

M (kN.m) 103.1 17.5 297.9 279.0 24.4 238.9 225.1 49.3 243.1
d (mm) 449.0 449.0 428.0 428.0 449.0 428.0 578.0 599.0 597.0
K/K' 0.44 0.07 1.39 1.30 0.10 1.11 0.58 0.12 0.58
x (mm) 82.38 49.89 212.20 212.20 49.89 212.20 144.46 66.56 151.32
As (mm2) 575.56 94.12 1995.13 1878.92 131.77 1633.15 1009.22 199.34 1057.18
As' (mm2) 0.00 0.00 512.61 396.40 0.00 150.63 0.00 0.00 0.00
As-min 195.00 195.00 195.00 195.00 195.00 195.00 253.50 253.50 253.50
Bending (Bottom Edge) ...
M (kN.m) 76.1 204.7 3.2 3.2 168.5 0.0 11.3 143.1 0.1
d (mm) 447.0 428.0 447.0 447.0 447.0 447.0 599.0 599.0 599.0
K/K' 0.33 0.96 0.01 0.01 0.72 0.00 0.03 0.34 0.00
x (mm) 59.62 199.22 49.67 49.67 145.36 49.67 66.56 83.92 66.56
As (mm2) 416.51 1391.79 17.23 17.39 1015.54 0.00 45.87 586.29 0.40
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 300.00 300.00 195.00 300.00 253.50 253.50 253.50
Shear and Bending Design ...
Vd (kN) 186.7 245.0 228.7 222.6 176.9 196.2
v (N/mm2) 1.39 1.91 1.78 1.73 1.02 1.10
vc (N/mm2) 0.46 0.64 0.69 0.69 0.59 0.64 0.55 0.39 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 157.7 149.8 161.7
Td (kN.m) 0.0 0.1 1.4
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 1500.0 1500.0 1500.0 1500.0 0.0 1500.0
Links H8-150 H8-300 H8-125 H8-150 H8-300 H8-150 H8-300 H8-300 H8-250
Deflection Check ...
L/d 14.02 < 26.73 OK 13.42 < 28.82 OK 10.02 < 31.2 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 603.19 2060.89 2060.89 402.12 1658.76 1658.76 402.12 1256.64
Bot Edge 1256.64 1658.76 1256.64 1256.64 1256.64 1256.64 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-5

Axis: E Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B10 L=6000mm
BwxH (mm) 300 x 650
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)

167.196

Shear
Force
(Envelope)
-242.475
253.832

91.565
Moment
(Envelope)
-201.691

Bending (Top Edge) ...

M (kN.m) 253.8 91.6
d (mm) 597.0 599.0
K/K' 0.61 0.22
x (mm) 159.04 66.56
As (mm2) 1111.11 370.09
As' (mm2) 0.00 0.00
As-min 253.50 253.50 253.50
Bending (Bottom Edge) ...
M (kN.m) 14.4 201.7 89.9
d (mm) 597.0 597.0 597.0
K/K' 0.03 0.48 0.22
x (mm) 66.33 122.54 66.33
As (mm2) 58.47 856.11 364.43
As' (mm2) 0.00 0.00 0.00
As-min 253.50 253.50 253.50
Shear and Bending Des ign ...
Vd (kN) 242.5 167.2
v (N/mm2) 1.35 0.93
vc (N/mm2) 0.50 0.45 0.34
v-max (N/mm2) 4.00 4.00
Vnom (kN) 173.3
Td (kN.m) 1.8
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1575.0 0.0
Links H8-175 H8-300 H8-300
Deflection Check ...
L/d 10.05 < 29.79 OK
Supplied Steel Areas (mm2)
Top Edge 1256.64 402.12 402.12
Bot Edge 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-6

Axis: 11 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B20 L=6000mm 1B21 L=5100mm 1B22 L=5400mm
BwxH (mm) 300 x 500 300 x 500 300 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
296.504
225.057
143.968

Shear
Force
(Envelope) -147.476 -152.596
-251.877
244.676 250.653 269.762
206.258
105.639 93.854
Moment
(Envelope)
-73.89
-186.798 -194.807

ending (Top Edge) ...

M (kN.m) 105.6 244.7 206.3 47.9 250.7 269.8 7.0 93.9
d (mm) 449.0 428.0 428.0 449.0 428.0 428.0 449.0 449.0
K/K' 0.45 1.14 0.96 0.20 1.17 1.26 0.03 0.40
x (mm) 84.64 212.20 201.23 49.89 212.20 212.20 49.89 74.36
As (mm2) 591.29 1668.67 1405.83 258.33 1704.15 1822.53 37.64 519.48
As' (mm2) 0.00 186.15 0.00 0.00 221.63 340.01 0.00 0.00
As-min 195.00 195.00 195.00 195.00 195.00 195.00 195.00 195.00 195.00
ending (Bottom Edge) ...
M (kN.m) 49.6 186.8 0.5 73.9 6.9 6.4 194.8 52.4
d (mm) 447.0 447.0 447.0 449.0 449.0 447.0 447.0 447.0
K/K' 0.21 0.80 0.00 0.31 0.03 0.03 0.83 0.22
x (mm) 49.67 164.98 49.67 57.49 49.89 49.67 173.93 49.67
As (mm2) 268.80 1152.58 2.87 401.64 37.14 34.47 1215.13 283.98
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 300.00 195.00 195.00 300.00 300.00 195.00 195.00
hear and Bending Design ...
Vd (kN) 147.5 225.1 152.6 296.5 251.9 144.0
v (N/mm2) 1.09 1.75 1.19 2.31 1.96 1.07
vc (N/mm2) 0.46 0.59 0.67 0.67 0.46 0.67 0.67 0.59 0.46
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 149.8 132.0 149.8
Td (kN.m) 0.7 3.1 1.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 2100.0 0.0 1300.0 1750.0 0.0
Links H8-300 H8-300 H8-150 H8-300 H8-300 H8-100 H8-125 H8-300 H8-300
Deflection Check ...
L/d 13.42 < 26.61 OK 11.36 < 45.58 OK 12.08 < 25.29 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 603.19 1859.82 1859.82 603.19 1859.82 1859.82 603.19 603.19
Bot Edge 1256.64 1256.64 1256.64 603.19 603.19 603.19 1256.64 1256.64 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-7

Axis: 4 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B27 L=1540mm 1B26 L=2230mm 1B25 L=2230mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)

138.563
65.171 75.584
Shear
Force -30.947 -34.189
-89.564
(Envelope)

104.479
31.473 31.692 34.526 42.296 41.042
Moment
(Envelope) 13.089 32.491
-25.086 -57.287

Bending (Top Edge) ...

M (kN.m) 31.5 18.7 31.7 34.5 1.2 42.3 41.0 62.5 104.5
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 428.0
K/K' 0.17 0.10 0.18 0.19 0.01 0.23 0.23 0.35 0.64
x (mm) 49.89 49.89 49.89 49.89 49.89 49.89 49.89 63.81 119.95
As (mm2) 169.70 100.59 170.89 186.17 6.34 228.06 221.30 341.76 642.48
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 25.1 16.7 5.9 57.3 17.0
d (mm) 449.0 449.0 449.0 449.0 449.0
K/K' 0.14 0.09 0.03 0.32 0.09
x (mm) 49.89 49.89 49.89 58.18 49.89
As (mm2) 135.26 90.07 32.07 311.62 91.55
As' (mm2) 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 30.9 65.2 89.6 138.6 34.2 75.6
v (N/mm2) 0.30 0.63 0.87 1.34 0.33 0.77
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.64
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 114.7
Td (kN.m) 0.1 1.0 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 800.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-200 H8-300 H8-300 H8-300
Deflection Check ...
L/d 3.43 < 57.97 OK 4.97 < 40.68 OK ---
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 1344.60
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-8

Axis: 4 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B24 L=5100mm 1B23 L=5400mm
BwxH (mm) 300 x 500 300 x 650
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
337.899
197.392

Shear
Force
(Envelope) -197.972
-388.144
378.275 395.353

158.584
86.546
Moment
(Envelope)
-192.473
-261.252

Bending (Top Edge) ...

M (kN.m) 158.6 10.6 378.3 395.4 2.8 86.5
d (mm) 428.0 449.0 427.0 577.0 599.0 599.0
K/K' 0.74 0.05 1.77 1.01 0.01 0.21
x (mm) 143.69 49.89 211.71 286.08 66.56 66.56
As (mm2) 1003.87 57.34 2493.46 2024.20 11.13 349.80
As' (mm2) 0.00 0.00 1014.40 25.57 0.00 0.00
As-min 195.00 195.00 195.00 253.50 253.50 253.50
Bending (Bottom Edge) ...
M (kN.m) 25.6 192.5 1.7 6.4 261.3 106.5
d (mm) 447.0 447.0 447.0 597.0 597.0 597.0
K/K' 0.11 0.82 0.01 0.02 0.63 0.26
x (mm) 49.67 171.30 49.67 66.33 164.45 66.33
As (mm2) 138.40 1196.73 9.31 26.02 1148.92 431.86
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 300.00 390.00 253.50 253.50
Shear and Bending Design ...
Vd (kN) 198.0 337.9 388.1 197.4
v (N/mm2) 1.54 2.64 2.24 1.10
vc (N/mm2) 0.60 0.59 0.74 0.63 0.50 0.50
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 149.8 181.7
Td (kN.m) 2.1 3.4
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 1225.0 2000.0 1500.0 1500.0
Links H8-175 H8-300 H10-125 H10-150 H8-300 H8-250
Deflection Check ...
L/d 11.41 < 24.77 OK 9.05 < 27.23 OK
Supplied Steel Areas (mm2)
Top Edge 1344.60 402.12 2513.27 2513.27 402.12 402.12
Bot Edge 1256.64 1256.64 1256.64 1256.64 1256.64 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-9

Axis: A Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B34 L=6000mm 1B33 L=6000mm 1B32 L=6000mm
BwxH (mm) 230 x 500 300 x 500 300 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
145.388
99.828 114.843

Shear
Force
(Envelope) -64.889
-103.132
-128.116
131.90 137.716 150.408 136.757
127.882

26.899
Moment
(Envelope)
-61.615 -54.108
-113.791

Bending (Top Edge) ...

M (kN.m) 26.9 9.0 131.9 137.7 0.4 150.4 127.9 13.3 136.8
d (mm) 449.0 449.0 447.0 447.0 449.0 447.0 447.0 449.0 447.0
K/K' 0.15 0.05 0.74 0.59 0.00 0.64 0.55 0.06 0.58
x (mm) 49.89 49.89 149.09 114.66 49.89 127.02 105.36 49.89 113.75
As (mm2) 145.04 48.58 798.53 801.07 1.94 887.38 736.08 71.72 794.67
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 195.00 195.00 195.00 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 34.9 61.6 0.3 113.8 3.0 54.1
d (mm) 449.0 449.0 447.0 447.0 447.0 449.0
K/K' 0.19 0.34 0.00 0.49 0.01 0.23
x (mm) 49.89 62.89 49.67 92.40 49.67 49.89
As (mm2) 188.03 336.86 1.79 645.56 16.38 291.76
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 195.00 195.00 195.00 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 64.9 99.8 128.1 145.4 103.1 114.8
v (N/mm2) 0.63 0.97 0.96 1.08 0.77 0.86
vc (N/mm2) 0.44 0.44 0.58 0.53 0.53 0.53 0.53 0.46 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 142.3 132.0
Td (kN.m) 0.0 0.4 0.4
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 13.36 < 37.38 OK 13.42 < 36.6 OK 13.36 < 56.71 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 942.48 942.48 402.12 942.48 942.48 402.12 942.48
Bot Edge 402.12 402.12 402.12 942.48 942.48 942.48 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-10

Axis: A Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B31 L=6000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
120.379

Shear
Force
(Envelope)
-145.715
152.13
84.338

Moment
(Envelope)

-118.972

Bending (Top Edge) ...

M (kN.m) 152.1 0.1 84.3
d (mm) 447.0 449.0 449.0
K/K' 0.65 0.00 0.36
x (mm) 128.73 49.89 66.24
As (mm2) 899.32 0.47 462.74
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 8.1 119.0 46.5
d (mm) 447.0 447.0 447.0
K/K' 0.03 0.51 0.20
x (mm) 49.67 97.12 49.67
As (mm2) 43.80 678.50 252.05
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Des ign ...
Vd (kN) 145.7 120.4
v (N/mm2) 1.09 0.89
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 142.3
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1650.0 0.0
Links H8-275 H8-300 H8-300
Deflection Check ...
L/d 13.42 < 36.29 OK
Supplied Steel Areas (mm2)
Top Edge 942.48 603.19 603.19
Bot Edge 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-11

Axis: D Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B38 L=2230mm 1B39 L=3770mm 1B40 L=6000mm
BwxH (mm) 230 x 500 230 x 500 300 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
149.089
90.935 86.729

Shear
Force -0.05
(Envelope)
-104.116
-182.186

104.425 114.418 103.23 103.895

Moment 34.587
(Envelope) -15.24 -20.913

-234.886
Bending (Top Edge) ...
M (kN.m) 12.6 55.8 104.4 114.4 49.9 103.2 103.9 1.1
d (mm) 449.0 449.0 447.0 447.0 449.0 449.0 449.0 449.0
K/K' 0.07 0.31 0.58 0.64 0.28 0.57 0.44 0.00
x (mm) 49.89 56.57 113.22 125.87 50.29 111.10 83.10 49.89
As (mm2) 67.72 302.97 606.43 674.15 269.34 595.05 580.55 5.70
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 15.2 20.9 71.9 234.9 130.8
d (mm) 449.0 449.0 447.0 428.0 447.0
K/K' 0.08 0.12 0.31 1.10 0.56
x (mm) 49.89 49.89 56.09 212.20 108.11
As (mm2) 82.18 112.76 391.83 1607.95 755.27
As' (mm2) 0.00 0.00 0.00 125.44 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 37.0 90.9 104.1 86.7 182.2 149.1
v (N/mm2) 0.36 0.88 1.01 0.84 1.35 1.11
vc (N/mm2) 0.44 0.44 0.58 0.58 0.44 0.50 0.46 0.64 0.59
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7 206.1
Td (kN.m) 0.0 0.1 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-175 H8-175 H8-175
Deflection Check ...
L/d --- 8.4 < 57.97 OK 14.02 < 22.7 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 942.48 942.48 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 1256.64 1658.76 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-12

Axis: I Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B41 L=6000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
235.862

Shear
Force
(Envelope)
-223.328

Moment
(Envelope)

-350.242
Bending (Top Edge) ...
M (kN.m) 4.6 9.3
d (mm) 447.0 447.0
K/K' 0.02 0.04
x (mm) 49.67 49.67
As (mm2) 24.73 50.30
As' (mm2) 0.00 0.00
As-min 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 204.1 350.2 203.7
d (mm) 447.0 427.0 447.0
K/K' 0.87 1.64 0.87
x (mm) 184.68 211.71 184.16
As (mm2) 1290.24 2321.06 1286.57
As' (mm2) 0.00 842.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 223.3 235.9
v (N/mm2) 1.67 1.76
vc (N/mm2) 0.63 0.74 0.63
v-max (N/mm2) 4.00 4.00
Vnom (kN) 193.6
Td (kN.m) 1.7
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1500.0 1500.0
Links H8-150 H8-225 H8-125
Deflection Check ...
L/d 14.05 < 17.79 OK
Supplied Steel Areas (mm2)
Top Edge 942.48 942.48 942.48
Bot Edge 1570.80 2513.27 1570.80

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-13

Axis: L Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B42 L=6000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
235.193

Shear
Force
(Envelope)
-232.508

Moment
(Envelope)

-390.903
Bending (Top Edge) ...
M (kN.m) 3.0 9.6
d (mm) 447.0 447.0
K/K' 0.01 0.04
x (mm) 49.67 49.67
As (mm2) 16.41 51.81
As' (mm2) 0.00 0.00
As-min 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 216.1 390.9 206.7
d (mm) 447.0 427.0 447.0
K/K' 0.92 1.83 0.88
x (mm) 199.02 211.71 187.75
As (mm2) 1390.38 2571.11 1311.65
As' (mm2) 0.00 1092.06 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 232.5 235.2
v (N/mm2) 1.73 1.75
vc (N/mm2) 0.63 0.77 0.63
v-max (N/mm2) 4.00 4.00
Vnom (kN) 197.8
Td (kN.m) 1.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1500.0 1500.0
Links H8-125 H8-225 H8-125
Deflection Check ...
L/d 14.05 < 18.2 OK
Supplied Steel Areas (mm2)
Top Edge 1256.64 1256.64 1256.64
Bot Edge 1570.80 2827.43 1570.80

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-14

Axis: K Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B43 L=6000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
240.974

Shear
Force
(Envelope)
-300.871

Moment
(Envelope)

-515.604
Bending (Top Edge) ...
M (kN.m) 11.2 3.8
d (mm) 447.0 447.0
K/K' 0.05 0.02
x (mm) 49.67 49.67
As (mm2) 60.56 20.75
As' (mm2) 0.00 0.00
As-min 300.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 276.2 515.6 222.9
d (mm) 447.0 427.0 447.0
K/K' 1.18 2.42 0.95
x (mm) 221.63 211.71 207.49
As (mm2) 1796.12 3337.99 1449.56
As' (mm2) 247.79 1858.94 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 300.9 241.0
v (N/mm2) 2.24 1.80
vc (N/mm2) 0.67 0.82 0.67
v-max (N/mm2) 4.00 4.00
Vnom (kN) 205.2
Td (kN.m) 0.7
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1500.0 1500.0
Links H10-150 H8-225 H8-125
Deflection Check ...
L/d 14.05 < 17.95 OK
Supplied Steel Areas (mm2)
Top Edge 1884.96 1884.96 1884.96
Bot Edge 1884.96 3455.75 1884.96

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-15

Axis: J Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B44 L=6000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
183.925

Shear
Force
(Envelope)
-194.373

Moment
(Envelope)

-333.336
Bending (Top Edge) ...
M (kN.m) 8.5 1.8
d (mm) 447.0 447.0
K/K' 0.04 0.01
x (mm) 49.67 49.67
As (mm2) 45.95 9.63
As' (mm2) 0.00 0.00
As-min 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 172.9 333.3 168.5
d (mm) 447.0 427.0 447.0
K/K' 0.74 1.56 0.72
x (mm) 150.03 211.71 145.35
As (mm2) 1048.18 2217.09 1015.42
As' (mm2) 0.00 738.04 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 194.4 183.9
v (N/mm2) 1.45 1.37
vc (N/mm2) 0.59 0.74 0.59
v-max (N/mm2) 4.00 4.00
Vnom (kN) 193.6
Td (kN.m) 0.8
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-225 H8-225 H8-225
Deflection Check ...
L/d 14.05 < 18.38 OK
Supplied Steel Areas (mm2)
Top Edge 942.48 942.48 942.48
Bot Edge 1256.64 2513.27 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-16

Axis: 10 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B47 L=3941mm 1B46 L=3502mm 1B45 L=3057mm
BwxH (mm) 230 x 500 230 x 500 230 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
90.907 81.483
65.389

Shear
Force
(Envelope) -33.437
-83.335
-103.032

Moment
(Envelope)
-92.729
-133.604 -128.708
Bending (Top Edge) ...
M (kN.m) 2.8 1.2
d (mm) 449.0 449.0
K/K' 0.02 0.01
x (mm) 49.89 49.89
As (mm2) 14.94 6.40
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 62.4 133.6 98.7 82.9 128.7 105.0 88.1 92.7 40.8
d (mm) 447.0 447.0 447.0 447.0 447.0 447.0 447.0 447.0 447.0
K/K' 0.35 0.75 0.55 0.46 0.72 0.59 0.49 0.52 0.23
x (mm) 64.05 151.43 106.17 87.35 144.73 114.00 93.41 98.93 49.67
As (mm2) 343.05 811.10 568.65 467.84 775.21 610.57 500.32 529.90 221.09
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 103.0 90.9 83.3 65.4 33.4 81.5
v (N/mm2) 1.00 0.88 0.81 0.63 0.32 0.79
vc (N/mm2) 0.58 0.58 0.58 0.58 0.58 0.58 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 130.2 130.2 122.3
Td (kN.m) 0.7 0.1 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.82 < 28.02 OK 7.83 < 29.19 OK 6.84 < 32.17 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 942.48 942.48 942.48 942.48 942.48 942.48 628.32 628.32 628.32

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-17

Axis: 5 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B48 L=3670mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
83.368

Shear
Force
(Envelope)
-82.958

Moment
(Envelope)

-88.281
Bending (Top Edge) ...
M (kN.m) 0.6
d (mm) 449.0
K/K' 0.00
x (mm) 49.89
As (mm2) 3.10
As' (mm2) 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 48.4 88.3 47.9
d (mm) 449.0 449.0 449.0
K/K' 0.21 0.37 0.20
x (mm) 49.89 69.58 49.89
As (mm2) 260.99 486.12 258.30
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 83.0 83.4
v (N/mm2) 0.62 0.62
vc (N/mm2) 0.46 0.46 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 132.0
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 8.17 < 28.04 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-18

Axis: 7 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B49 L=3160mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
71.105

Shear
Force
(Envelope)
-75.466

Moment
(Envelope)

-67.464
Bending (Top Edge) ...
M (kN.m) 2.2
d (mm) 449.0
K/K' 0.01
x (mm) 49.89
As (mm2) 11.83
As' (mm2) 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 36.9 67.5 37.8
d (mm) 449.0 449.0 449.0
K/K' 0.16 0.29 0.16
x (mm) 49.89 52.20 49.89
As (mm2) 198.76 364.66 203.70
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 75.5 71.1
v (N/mm2) 0.56 0.53
vc (N/mm2) 0.46 0.46 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 132.0
Td (kN.m) 0.8
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 7.04 < 36.84 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-19

Axis: C Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B52 L=6000mm 1B53 L=6000mm
BwxH (mm) 300 x 500 300 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
172.834 152.47

Shear
Force
(Envelope) -113.484

-231.138
250.523 279.007

65.369
Moment
(Envelope)
-107.096
-220.045

Bending (Top Edge) ...

M (kN.m) 65.4 37.0 250.5 279.0 2.6 1.5
d (mm) 449.0 449.0 428.0 428.0 449.0 449.0
K/K' 0.28 0.16 1.17 1.30 0.01 0.01
x (mm) 50.48 49.89 212.20 212.20 49.89 49.89
As (mm2) 352.70 199.40 1703.35 1879.23 14.18 8.22
As' (mm2) 0.00 0.00 220.84 396.72 0.00 0.00
As-min 195.00 195.00 195.00 195.00 300.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 56.2 107.1 0.7 220.0 131.2
d (mm) 449.0 449.0 447.0 428.0 447.0
K/K' 0.24 0.45 0.00 1.03 0.56
x (mm) 49.89 85.93 49.67 212.20 108.48
As (mm2) 303.13 600.30 3.90 1517.41 757.90
As' (mm2) 0.00 0.00 0.00 34.90 0.00
As-min 195.00 195.00 300.00 300.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 113.5 172.8 231.1 152.5
v (N/mm2) 0.84 1.35 1.80 1.13
vc (N/mm2) 0.46 0.46 0.69 0.69 0.64 0.59
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 132.0 206.1
Td (kN.m) 0.0 0.1
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 1575.0 1500.0 0.0
Links H8-300 H8-300 H8-175 H8-150 H8-175 H8-175
Deflection Check ...
L/d 13.36 < 29.47 OK 14.02 < 23.97 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 603.19 2060.89 2060.89 402.12 402.12
Bot Edge 603.19 603.19 603.19 1256.64 1658.76 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-20

Axis: 2 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B54 L=3000mm 1B18 L=3000mm 1B17 L=5100mm
BwxH (mm) 300 x 500 300 x 500 300 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
204.03
134.004 107.192

Shear
Force
(Envelope) -62.973
-134.004
-178.04

232.247
143.368
109.84
39.517
Moment
(Envelope) 3.489
-34.72
-100.503 -129.308

Bending (Top Edge) ...

M (kN.m) 39.5 49.5 109.8 143.4 34.8 232.2
d (mm) 449.0 449.0 447.0 447.0 449.0 428.0
K/K' 0.17 0.21 0.47 0.61 0.15 1.08
x (mm) 49.89 49.89 88.84 120.12 49.89 212.20
As (mm2) 213.08 266.72 620.69 839.16 187.69 1592.44
As' (mm2) 0.00 0.00 0.00 0.00 0.00 109.92
As-min 195.00 195.00 195.00 195.00 195.00 195.00 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 58.9 100.5 58.9 28.5 34.7 2.1 18.6 129.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 447.0 447.0
K/K' 0.25 0.43 0.25 0.12 0.15 0.01 0.08 0.55
x (mm) 49.89 80.13 49.89 49.89 49.89 49.89 49.67 106.70
As (mm2) 317.63 559.78 317.63 153.55 187.21 11.32 100.93 745.41
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 195.00 195.00 195.00 195.00 195.00 195.00 195.00 195.00 300.00
Shear and Bending Design ...
Vd (kN) 134.0 134.0 63.0 107.2 178.0 204.0
v (N/mm2) 0.99 0.99 0.47 0.80 1.33 1.59
vc (N/mm2) 0.46 0.46 0.46 0.46 0.46 0.53 0.53 0.53 0.67
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 132.0 132.0 142.3
Td (kN.m) 0.1 0.2 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 1225.0 1225.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-175 H8-300 H8-175
Deflection Check ...
L/d 6.68 < 23.89 OK 6.68 < 58.75 OK 11.41 < 32.09 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 603.19 942.48 942.48 402.12 1859.82
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-21

Axis: 2 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B16 L=5400mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
184.793

Shear
Force
(Envelope)
-240.329
255.592

96.167

Moment
(Envelope)

-195.905

Bending (Top Edge) ...

M (kN.m) 255.6 14.7 96.2
d (mm) 428.0 449.0 449.0
K/K' 1.19 0.06 0.41
x (mm) 212.20 49.89 76.36
As (mm2) 1735.62 79.44 533.44
As' (mm2) 253.10 0.00 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 2.5 195.9 75.1
d (mm) 447.0 447.0 447.0
K/K' 0.01 0.84 0.32
x (mm) 49.67 175.18 58.83
As (mm2) 13.39 1223.84 411.01
As' (mm2) 0.00 0.00 0.00
As-min 300.00 195.00 195.00
Shear and Bending Des ign ...
Vd (kN) 240.3 184.8
v (N/mm2) 1.87 1.37
vc (N/mm2) 0.67 0.59 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 149.8
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1500.0 1350.0
Links H8-125 H8-300 H8-150
Deflection Check ...
L/d 12.08 < 25.12 OK
Supplied Steel Areas (mm2)
Top Edge 1859.82 603.19 603.19
Bot Edge 1256.64 1256.64 1256.64

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-22

Axis: 3 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B55 L=3000mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
65.487

Shear
Force
(Envelope)
-65.855

Moment
(Envelope)

-53.611
Bending (Top Edge) ...
M (kN.m) 0.6
d (mm) 449.0
K/K' 0.00
x (mm) 49.89
As (mm2) 3.22
As' (mm2) 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 30.0 53.6 30.4
d (mm) 449.0 449.0 449.0
K/K' 0.13 0.23 0.13
x (mm) 49.89 49.89 49.89
As (mm2) 161.94 289.07 163.74
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 65.9 65.5
v (N/mm2) 0.49 0.49
vc (N/mm2) 0.46 0.46 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 132.0
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 6.68 < 43.62 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-23

Axis: 12 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B57 L=3502mm 1B56 L=3057mm
BwxH (mm) 230 x 500 230 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
66.951

10.971
Shear
Force -13.877
(Envelope)
-70.944

Moment
(Envelope)

-104.797 -102.153
Bending (Top Edge) ...
M (kN.m) 0.3 0.5
d (mm) 449.0 449.0
K/K' 0.00 0.00
x (mm) 49.89 49.89
As (mm2) 1.72 2.84
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 40.8 103.1 104.7 102.2 97.6 34.9
d (mm) 447.0 447.0 447.0 447.0 447.0 447.0
K/K' 0.23 0.58 0.58 0.57 0.54 0.19
x (mm) 49.67 111.59 113.55 110.41 104.83 49.67
As (mm2) 221.18 597.67 608.19 591.35 561.48 189.08
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 70.9 11.8 23.8 67.0
v (N/mm2) 0.69 0.11 0.23 0.65
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 122.3 122.3
Td (kN.m) 0.1 0.2
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 7.83 < 28.24 OK 6.84 < 30.26 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 628.32 628.32 628.32 628.32 628.32 628.32

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-24

Axis: 1 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B60 L=3000mm 1B30 L=3000mm 1B29 L=5100mm
BwxH (mm) 230 x 500 300 x 500 300 x 500
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
134.844
88.684 81.465

Shear
Force
(Envelope) -49.765
-88.684
-119.179

146.339
78.534 93.422
39.038
Moment -24.131
(Envelope) -25.91 -24.527
-66.513 -80.448

Bending (Top Edge) ...

M (kN.m) 0.0 39.0 27.0 78.5 93.4 17.4 146.3
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 447.0
K/K' 0.00 0.17 0.11 0.33 0.40 0.07 0.63
x (mm) 49.89 49.89 49.89 61.36 73.99 49.89 123.01
As (mm2) 0.00 210.50 145.45 428.65 516.88 94.02 859.40
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 195.00 195.00 195.00 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 37.5 66.5 39.3 25.9 25.9 1.7 13.0 80.4 2.2
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.21 0.37 0.22 0.11 0.11 0.01 0.06 0.34 0.01
x (mm) 49.89 68.28 49.89 49.89 49.89 49.89 49.89 62.96 49.89
As (mm2) 202.08 365.74 211.64 139.51 139.71 9.04 70.36 439.85 12.06
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 195.00 195.00 195.00 195.00 195.00 195.00
Shear and Bending Design ...
Vd (kN) 88.7 88.7 49.8 81.5 119.2 134.8
v (N/mm2) 0.86 0.86 0.37 0.60 0.88 1.01
vc (N/mm2) 0.44 0.44 0.44 0.46 0.40 0.46 0.46 0.46 0.59
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 123.8 132.0
Td (kN.m) 0.0 0.2 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 6.68 < 26.1 OK 6.68 < 56.71 OK 11.36 < 40.38 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 1256.64
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-25

Axis: 1 Storey: 1 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B28 L=5400mm
BwxH (mm) 300 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
118.584

Shear
Force
(Envelope)
-155.467
163.093

68.867

Moment
(Envelope)

-117.73

Bending (Top Edge) ...

M (kN.m) 163.1 8.7 68.9
d (mm) 447.0 449.0 449.0
K/K' 0.70 0.04 0.29
x (mm) 139.79 49.89 53.35
As (mm2) 976.62 46.97 372.70
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Bending (Bottom Edge) ...
M (kN.m) 2.5 117.7 52.0
d (mm) 447.0 447.0 447.0
K/K' 0.01 0.50 0.22
x (mm) 49.67 95.98 49.67
As (mm2) 13.27 670.57 281.72
As' (mm2) 0.00 0.00 0.00
As-min 195.00 195.00 195.00
Shear and Bending Des ign ...
Vd (kN) 155.5 118.6
v (N/mm2) 1.16 0.88
vc (N/mm2) 0.59 0.53 0.40
v-max (N/mm2) 4.00 4.00
Vnom (kN) 142.3
Td (kN.m) 0.1
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 1375.0 0.0
Links H8-275 H8-300 H8-300
Deflection Check ...
L/d 12.08 < 35.39 OK
Supplied Steel Areas (mm2)
Top Edge 1256.64 402.12 402.12
Bot Edge 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-26

Axis: 6 Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
1B62 L=1540mm 1B61 L=2230mm
BwxH (mm) 230 x 500 230 x 500
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
66.339

27.209

Shear
Force -1.913
(Envelope)
-67.518
53.145 48.173

10.423
Moment
(Envelope) 0.967
-14.834

Bending (Top Edge) ...

M (kN.m) 5.8 28.4 53.1 48.2 21.8 10.4
d (mm) 449.0 449.0 449.0 449.0 449.0 449.0
K/K' 0.03 0.16 0.29 0.27 0.12 0.06
x (mm) 49.89 49.89 53.72 49.89 49.89 49.89
As (mm2) 31.32 153.38 287.73 259.75 117.52 56.20
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 0.5 14.8 14.1
d (mm) 449.0 449.0 449.0
K/K' 0.00 0.08 0.08
x (mm) 49.89 49.89 49.89
As (mm2) 2.64 79.99 76.01
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 23.2 46.0 67.5 27.2
v (N/mm2) 0.23 0.45 0.65 0.26
vc (N/mm2) 0.44 0.44 0.44 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 114.7 114.7
Td (kN.m) 0.1 0.1
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-300 H8-300 H8-300 H8-300 H8-300 H8-300
Deflection Check ...
L/d 3.43 < 57.97 OK 4.97 < 57.97 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-27

Axis: B Storey: 1 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

1B63 L=2230mm
BwxH (mm) 230 x 500
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
41.879

Shear
Force
(Envelope)
-38.966
16.174
12.93

Moment
(Envelope)

-19.144
Bending (Top Edge) ...
M (kN.m) 12.9 16.2
d (mm) 449.0 449.0
K/K' 0.07 0.09
x (mm) 49.89 49.89
As (mm2) 69.72 87.21
As' (mm2) 0.00 0.00
As-min 149.50 149.50 149.50
Bending (Bottom Edge) ...
M (kN.m) 16.9 19.1 15.3
d (mm) 449.0 449.0 449.0
K/K' 0.09 0.11 0.08
x (mm) 49.89 49.89 49.89
As (mm2) 90.97 103.23 82.24
As' (mm2) 0.00 0.00 0.00
As-min 149.50 149.50 149.50
Shear and Bending Design ...
Vd (kN) 39.0 41.9
v (N/mm2) 0.38 0.41
vc (N/mm2) 0.44 0.44 0.44
v-max (N/mm2) 4.00 4.00
Vnom (kN) 114.7
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-300 H8-300 H8-300
Deflection Check ...
L/d 4.97 < 44.6 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-28

Axis: G Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B1 L=6000mm 2B2 L=6000mm 2B3 L=6000mm
BwxH (mm) 300 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
59.881 55.601 61.762

Shear
Force
(Envelope)
-51.97 -55.58 -55.38
61.167 55.984 57.841 54.246 59.622
34.549

Moment
(Envelope)
-38.685 -32.667 -35.851

Bending (Top Edge) ...

M (kN.m) 34.5 0.8 61.2 56.0 4.0 57.8 54.2 1.9 59.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.24 0.01 0.43 0.39 0.03 0.41 0.38 0.01 0.42
x (mm) 38.78 38.78 62.78 57.00 38.78 59.06 55.08 38.78 61.05
As (mm2) 239.67 5.23 438.61 398.22 27.89 412.61 384.83 13.02 426.50
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 10.3 38.7 0.5 32.7 0.7 1.0 35.9 0.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.07 0.27 0.00 0.23 0.00 0.01 0.25 0.00
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 71.47 268.36 3.34 226.61 4.71 7.18 248.70 4.60
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 52.0 59.9 55.6 55.6 55.4 61.8
v (N/mm2) 0.50 0.57 0.53 0.53 0.53 0.59
vc (N/mm2) 0.46 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9 121.9
Td (kN.m) 0.0 0.0 0.2
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 56.41 OK 17.19 < 57.9 OK 17.19 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-29

Axis: G Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B4 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
51.532

Shear
Force
(Envelope)
-60.378
63.219
32.698

Moment
(Envelope)
-40.056

Bending (Top Edge) ...

M (kN.m) 63.2 2.0 32.7
d (mm) 349.0 349.0 349.0
K/K' 0.44 0.01 0.23
x (mm) 65.10 38.78 38.78
As (mm2) 454.80 13.61 226.83
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 0.6 40.1 11.9
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.28 0.08
x (mm) 38.78 39.83 38.78
As (mm2) 4.09 278.27 82.72
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Des ign ...
Vd (kN) 60.4 51.5
v (N/mm2) 0.58 0.49
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 54.99 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-30

Axis: F Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B5 L=6000mm 2B6 L=6000mm
BwxH (mm) 300 x 400 300 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
58.775 53.204

Shear
Force
(Envelope)
-52.483 -58.321
59.728 60.917
39.656 43.806

Moment
(Envelope)
-35.062 -32.98

Bending (Top Edge) ...

M (kN.m) 39.7 0.2 59.7 60.9 0.7 43.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.28 0.00 0.42 0.43 0.01 0.31
x (mm) 39.41 38.78 61.17 62.50 38.78 43.80
As (mm2) 275.34 1.68 427.33 436.65 5.11 305.97
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 5.5 35.1 1.5 2.0 33.0 5.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.25 0.01 0.01 0.23 0.04
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 38.18 243.23 10.73 14.19 228.79 37.08
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 52.5 58.8 58.3 53.2
v (N/mm2) 0.50 0.56 0.56 0.51
vc (N/mm2) 0.46 0.53 0.53 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 57.9 OK 17.19 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-31

Axis: E Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B7 L=6000mm 2B8 L=6000mm 2B9 L=6000mm
BwxH (mm) 300 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
59.411 56.742 54.75

Shear
Force
(Envelope)
-52.729 -55.406 -56.393
61.117 61.013 56.686
52.31 53.44
38.772

Moment
(Envelope)
-36.643 -31.951 -33.917

Bending (Top Edge) ...

M (kN.m) 38.8 0.8 61.1 52.3 5.0 61.0 56.7 1.2 53.4
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.27 0.01 0.43 0.37 0.03 0.43 0.40 0.01 0.37
x (mm) 38.78 38.78 62.73 52.96 38.78 62.61 57.78 38.78 54.20
As (mm2) 268.97 5.74 438.22 370.00 34.49 437.40 403.65 8.48 378.64
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 9.1 36.6 2.1 32.0 0.7 0.5 33.9 0.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.26 0.01 0.22 0.01 0.00 0.24 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 63.30 254.19 14.42 221.65 5.01 3.21 235.29 5.22
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 52.7 59.4 55.4 56.7 56.4 54.8
v (N/mm2) 0.50 0.57 0.53 0.54 0.54 0.52
vc (N/mm2) 0.46 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9 121.9
Td (kN.m) 0.0 0.0 0.1
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 57.9 OK 17.19 < 57.9 OK 17.19 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-32

Axis: E Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B10 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
53.114

Shear
Force
(Envelope)
-58.23
55.899
38.265

Moment
(Envelope)
-39.52

Bending (Top Edge) ...

M (kN.m) 55.9 0.3 38.3
d (mm) 349.0 349.0 349.0
K/K' 0.39 0.00 0.27
x (mm) 56.91 38.78 38.78
As (mm2) 397.56 2.39 265.45
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 0.5 39.5 7.4
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.28 0.05
x (mm) 38.78 39.27 38.78
As (mm2) 3.37 274.34 51.06
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 58.2 53.1
v (N/mm2) 0.56 0.51
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 55.54 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-33

Axis: 2 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B14 L=3000mm 2B13 L=3000mm 2B12 L=5100mm
BwxH (mm) 300 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
47.406
28.54 29.681

Shear
Force
(Envelope) -26.794 -25.932
-46.711

35.995 38.541
21.362
14.949
7.714 9.867
Moment
(Envelope) 2.538
-12.543 -6.765
-24.95

Bending (Top Edge) ...

M (kN.m) 7.7 0.1 9.9 14.9 6.6 21.4 36.0 0.8 38.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.00 0.07 0.10 0.05 0.15 0.25 0.01 0.27
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 53.52 0.64 68.45 103.70 45.55 148.19 249.70 5.36 267.37
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 5.5 12.5 4.6 1.0 6.8 0.3 1.8 24.9 0.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.09 0.03 0.01 0.05 0.00 0.01 0.18 0.00
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 38.06 87.01 32.00 7.27 46.93 1.93 12.67 173.08 3.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 26.8 28.5 25.9 29.7 46.7 47.4
v (N/mm2) 0.26 0.27 0.25 0.28 0.45 0.45
vc (N/mm2) 0.46 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9 121.9
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 8.6 < 57.9 OK 8.6 < 57.9 OK 14.61 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-34

Axis: 2 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B11 L=5400mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
48.01

Shear
Force
(Envelope)
-52.524
47.047
33.38

Moment
(Envelope)
-29.226

Bending (Top Edge) ...

M (kN.m) 47.0 1.2 33.4
d (mm) 349.0 349.0 349.0
K/K' 0.33 0.01 0.23
x (mm) 47.26 38.78 38.78
As (mm2) 330.17 8.08 231.56
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 0.4 29.2 6.4
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.21 0.05
x (mm) 38.78 38.78 38.78
As (mm2) 2.52 202.75 44.73
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 52.5 48.0
v (N/mm2) 0.50 0.46
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 15.47 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-35

Axis: 11 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B17 L=6000mm 2B16 L=5100mm 2B15 L=5400mm
BwxH (mm) 300 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
94.401 90.497
66.449

Shear
Force
(Envelope)
-68.813 -58.314
-89.51
94.121 90.113
72.029 77.617
54.415 44.399

Moment
(Envelope)
-24.307

-74.039 -72.722

Bending (Top Edge) ...

M (kN.m) 54.4 94.1 72.0 18.9 77.6 90.1 1.8 44.4
d (mm) 349.0 347.0 347.0 349.0 347.0 347.0 349.0 349.0
K/K' 0.38 0.67 0.51 0.13 0.55 0.64 0.01 0.31
x (mm) 55.27 103.08 75.79 38.78 82.46 97.93 38.78 44.43
As (mm2) 386.12 720.11 529.46 131.24 576.07 684.18 12.68 310.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 11.7 74.0 0.7 24.3 0.2 0.4 72.7 11.7
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.08 0.52 0.01 0.17 0.00 0.00 0.51 0.08
x (mm) 38.78 77.61 38.78 38.78 38.78 38.78 76.06 38.78
As (mm2) 80.96 542.19 5.17 168.62 1.46 2.87 531.37 81.23
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 68.8 94.4 58.3 90.5 89.5 66.4
v (N/mm2) 0.66 0.91 0.56 0.87 0.86 0.63
vc (N/mm2) 0.46 0.53 0.62 0.62 0.53 0.62 0.62 0.53 0.46
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9 121.9
Td (kN.m) 0.3 0.8 0.4
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 30.55 OK 14.61 < 57.9 OK 15.47 < 31.23 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 942.48 942.48 402.12 942.48 942.48 402.12 402.12
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-36

Axis: 9 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B27 L=6000mm 2B28 L=5100mm 2B29 L=5400mm
BwxH (mm) 300 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
118.671 132.728
77.136

Shear
Force
(Envelope)
-78.661 -77.695
-133.137
121.666 125.533 136.477
100.083
68.477 56.113

Moment
(Envelope)
-53.914
-97.152 -93.99

Bending (Top Edge) ...

M (kN.m) 68.5 121.7 100.1 17.4 125.5 136.5 56.1
d (mm) 349.0 347.0 347.0 349.0 347.0 347.0 349.0
K/K' 0.48 0.86 0.71 0.12 0.89 0.97 0.39
x (mm) 71.12 141.34 110.91 38.78 147.20 164.63 57.14
As (mm2) 496.84 987.42 774.82 121.00 1028.37 1150.16 399.21
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 6.1 97.2 0.0 53.9 4.6 5.2 94.0 11.1
d (mm) 347.0 347.0 347.0 349.0 349.0 347.0 347.0 347.0
K/K' 0.04 0.69 0.00 0.38 0.03 0.04 0.67 0.08
x (mm) 38.56 107.03 38.56 54.72 38.78 38.56 102.91 38.56
As (mm2) 42.36 747.73 0.17 382.28 31.92 36.28 718.93 77.16
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 78.7 118.7 77.7 132.7 133.1 77.1
v (N/mm2) 0.75 1.14 0.75 1.28 1.28 0.74
vc (N/mm2) 0.53 0.62 0.68 0.68 0.53 0.68 0.68 0.62 0.46
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 131.2 121.9 131.2
Td (kN.m) 0.3 2.1 2.4
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.29 < 31.52 OK 14.61 < 42.91 OK 15.56 < 31.28 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 603.19 1256.64 1256.64 402.12 1256.64 1256.64 402.12 402.12
Bot Edge 942.48 942.48 942.48 603.19 603.19 603.19 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-37

Axis: 4 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B34 L=1540mm 2B33 L=2230mm 2B32 L=2230mm
BwxH (mm) 230 x 400 230 x 400 230 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)

52.815
17.068 17.894
Shear
Force -11.59 -21.607
(Envelope) -29.987

22.132 21.702 16.594

4.524 8.154 11.362
Moment 9.992
(Envelope) 1.767
-2.348
-15.75

Bending (Top Edge) ...

M (kN.m) 4.5 3.9 8.2 11.4 1.4 22.1 21.7 12.7 16.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.04 0.07 0.10 0.01 0.20 0.20 0.12 0.15
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 31.38 27.31 56.56 78.82 9.49 153.53 150.55 88.21 115.11
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 2.0 2.3 2.8 15.7 1.4
d (mm) 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.02 0.03 0.14 0.01
x (mm) 38.78 38.78 38.78 38.78 38.78
As (mm2) 13.61 16.29 19.09 109.26 9.93
As' (mm2) 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 11.6 8.5 30.0 52.8 21.6 17.9
v (N/mm2) 0.14 0.11 0.37 0.66 0.27 0.22
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.58
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 106.3
Td (kN.m) 0.0 0.3 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 4.41 < 59.44 OK 6.39 < 59.44 OK ---
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 603.19
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-38

Axis: 4 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B31 L=5100mm 2B30 L=5400mm
BwxH (mm) 300 x 400 300 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
90.403
57.284

Shear
Force
(Envelope)
-59.353
-98.005
89.881 96.536
44.888 37.471

Moment
(Envelope)
-50.891 -51.648

Bending (Top Edge) ...

M (kN.m) 44.9 1.5 89.9 96.5 37.5
d (mm) 349.0 349.0 347.0 347.0 349.0
K/K' 0.31 0.01 0.64 0.69 0.26
x (mm) 44.95 38.78 97.64 106.22 38.78
As (mm2) 314.03 10.18 682.12 742.09 259.94
As' (mm2) 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 5.5 50.9 2.5 0.4 51.6 9.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.36 0.02 0.00 0.36 0.07
x (mm) 38.78 51.42 38.78 38.78 52.24 38.78
As (mm2) 37.86 359.20 17.54 3.12 364.96 67.78
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 59.4 90.4 98.0 57.3
v (N/mm2) 0.57 0.87 0.94 0.55
vc (N/mm2) 0.53 0.53 0.62 0.62 0.53 0.46
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9
Td (kN.m) 0.5 0.6
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 14.61 < 45.23 OK 15.47 < 44.63 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 942.48 942.48 402.12 402.12
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-39

Axis: D Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B35 L=2230mm 2B36 L=3770mm 2B37 L=6000mm
BwxH (mm) 230 x 400 230 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)

38.227
28.067

Shear
Force -3.864
(Envelope)
-38.453
-59.326

39.572 45.075
24.284 24.623
Moment 12.015
(Envelope) -3.965 -7.589

-71.91
Bending (Top Edge) ...
M (kN.m) 2.4 19.8 39.6 45.1 19.6 24.3 24.6 0.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.18 0.36 0.41 0.18 0.22 0.17 0.00
x (mm) 38.78 38.78 52.20 60.12 38.78 38.78 38.78 38.78
As (mm2) 16.92 137.04 279.61 322.02 136.06 168.46 170.81 3.42
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 4.0 1.0 7.6 26.6 71.9 41.1
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.04 0.01 0.07 0.19 0.50 0.29
x (mm) 38.78 38.78 38.78 38.78 75.11 40.93
As (mm2) 27.50 7.13 52.65 184.61 524.72 285.91
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 12.3 38.2 38.5 28.1 59.3 51.7
v (N/mm2) 0.15 0.48 0.48 0.35 0.57 0.49
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.58 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3 121.9
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 6.39 < 59.44 OK 10.8 < 59.44 OK 17.19 < 31.66 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-40

Axis: B Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B38 L=2230mm
BwxH (mm) 230 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
20.356

Shear
Force
(Envelope)
-18.913

4.291
2.504
Moment
(Envelope)

-9.01
Bending (Top Edge) ...
M (kN.m) 2.5 4.3
d (mm) 349.0 349.0
K/K' 0.02 0.04
x (mm) 38.78 38.78
As (mm2) 17.37 29.77
As' (mm2) 0.00 0.00
As-min 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 5.5 9.0 4.4
d (mm) 349.0 349.0 349.0
K/K' 0.05 0.08 0.04
x (mm) 38.78 38.78 38.78
As (mm2) 38.26 62.51 30.74
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 18.9 20.4
v (N/mm2) 0.24 0.25
vc (N/mm2) 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00
Vnom (kN) 106.3
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 6.39 < 45.72 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-41

Axis: C Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B41 L=6000mm 2B42 L=6000mm
BwxH (mm) 300 x 400 300 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
62.542
44.062

Shear
Force
(Envelope)
-50.567
-68.071
70.015 76.772

30.199

Moment
(Envelope)
-39.115
-52.018

Bending (Top Edge) ...

M (kN.m) 30.2 4.8 70.0 76.8 1.9 0.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.21 0.03 0.49 0.54 0.01 0.00
x (mm) 38.78 38.78 72.90 80.85 38.78 38.78
As (mm2) 209.50 33.23 509.29 564.83 12.99 3.73
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 13.4 39.1 0.6 0.5 52.0 32.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.09 0.27 0.00 0.00 0.37 0.23
x (mm) 38.78 38.84 38.78 38.78 52.64 38.78
As (mm2) 93.10 271.37 4.46 3.27 367.78 226.41
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 50.6 62.5 68.1 44.1
v (N/mm2) 0.48 0.60 0.65 0.42
vc (N/mm2) 0.46 0.53 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 121.9 121.9
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 55.96 OK 17.19 < 44.35 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-42

Axis: I Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B43 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
54.368

Shear
Force
(Envelope)
-54.73

Moment
(Envelope)

-80.466
Bending (Top Edge) ...
M (kN.m) 0.8 2.9
d (mm) 349.0 349.0
K/K' 0.01 0.02
x (mm) 38.78 38.78
As (mm2) 5.45 19.84
As' (mm2) 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 44.9 80.5 42.3
d (mm) 349.0 349.0 349.0
K/K' 0.32 0.56 0.30
x (mm) 44.96 85.28 42.15
As (mm2) 314.08 595.81 294.48
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 54.7 54.4
v (N/mm2) 0.52 0.52
vc (N/mm2) 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.6
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 21.09 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-43

Axis: J Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B44 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
54.957

Shear
Force
(Envelope)
-55.633

Moment
(Envelope)

-81.306
Bending (Top Edge) ...
M (kN.m) 2.7 0.7
d (mm) 349.0 349.0
K/K' 0.02 0.00
x (mm) 38.78 38.78
As (mm2) 18.51 4.60
As' (mm2) 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 42.9 81.3 44.3
d (mm) 349.0 349.0 349.0
K/K' 0.30 0.57 0.31
x (mm) 42.86 86.30 44.30
As (mm2) 299.40 602.91 309.52
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 55.6 55.0
v (N/mm2) 0.53 0.52
vc (N/mm2) 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 20.79 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-44

Axis: K Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B45 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
55.01

Shear
Force
(Envelope)
-55.585

Moment
(Envelope)

-81.122
Bending (Top Edge) ...
M (kN.m) 2.7 1.0
d (mm) 349.0 349.0
K/K' 0.02 0.01
x (mm) 38.78 38.78
As (mm2) 18.71 6.83
As' (mm2) 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 42.8 81.1 44.0
d (mm) 349.0 349.0 349.0
K/K' 0.30 0.57 0.31
x (mm) 42.78 86.08 44.01
As (mm2) 298.87 601.36 307.45
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 55.6 55.0
v (N/mm2) 0.53 0.53
vc (N/mm2) 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 20.85 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-45

Axis: L Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B46 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
61.407

Shear
Force
(Envelope)
-56.005

Moment
(Envelope)

-84.383
Bending (Top Edge) ...
M (kN.m) 0.7 2.3
d (mm) 349.0 349.0
K/K' 0.01 0.02
x (mm) 38.78 38.78
As (mm2) 5.16 16.28
As' (mm2) 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 46.3 84.4 48.7
d (mm) 347.0 347.0 347.0
K/K' 0.33 0.60 0.35
x (mm) 46.73 90.74 49.37
As (mm2) 326.45 633.90 344.93
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 56.0 61.4
v (N/mm2) 0.53 0.59
vc (N/mm2) 0.62 0.62 0.62
v-max (N/mm2) 4.00 4.00
Vnom (kN) 131.2
Td (kN.m) 0.3
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.29 < 26.76 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12
Bot Edge 942.48 942.48 942.48

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-46

Axis: 1 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B52 L=3000mm 2B51 L=3000mm 2B50 L=5100mm
BwxH (mm) 230 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
49.069
30.614 27.304

Shear
Force
(Envelope) -21.881 -28.26
-45.847
43.256
32.228
15.647 19.447 19.33
2.576
Moment
4.882
(Envelope) -6.416
-11.884
-25.48

Bending (Top Edge) ...

M (kN.m) 2.6 0.3 15.6 19.4 7.6 19.3 32.2 2.9 43.3
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.02 0.00 0.14 0.14 0.05 0.14 0.23 0.02 0.30
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 43.21
As (mm2) 17.87 1.90 108.54 134.90 52.40 134.09 223.57 20.09 301.89
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 7.0 11.9 0.3 0.2 6.4 0.5 2.9 25.5 0.5
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.06 0.11 0.00 0.00 0.05 0.00 0.02 0.18 0.00
x (mm) 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 48.22 82.44 1.76 1.72 44.51 3.16 19.91 176.76 3.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 21.9 30.6 28.3 27.3 45.8 49.1
v (N/mm2) 0.27 0.38 0.27 0.26 0.44 0.47
vc (N/mm2) 0.51 0.51 0.58 0.53 0.46 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 114.5 121.9
Td (kN.m) 0.0 0.0 0.0
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 8.6 < 59.44 OK 8.6 < 57.9 OK 14.61 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-47

Axis: 1 Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B49 L=5400mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
46.159

Shear
Force
(Envelope)
-54.578
50.97
26.008

Moment
(Envelope)
-31.819

Bending (Top Edge) ...

M (kN.m) 51.0 2.2 26.0
d (mm) 349.0 349.0 349.0
K/K' 0.36 0.02 0.18
x (mm) 51.50 38.78 38.78
As (mm2) 359.79 15.61 180.42
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 0.4 31.8 10.4
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.22 0.07
x (mm) 38.78 38.78 38.78
As (mm2) 2.76 220.73 71.85
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Des ign ...
Vd (kN) 54.6 46.2
v (N/mm2) 0.52 0.44
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 15.47 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-48

Axis: A Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B56 L=6000mm 2B55 L=6000mm 2B54 L=6000mm
BwxH (mm) 230 x 400 300 x 400 300 x 400
Flange BfxHf --- --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
61.103 55.151 53.551

Shear
Force
(Envelope)
-45.745 -50.199
-56.235
65.48 60.95
55.286 48.761 53.603

16.082
Moment
(Envelope)
-33.028 -29.944
-43.489

Bending (Top Edge) ...

M (kN.m) 16.1 1.0 65.5 60.9 6.3 55.3 48.8 2.7 53.6
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.15 0.01 0.60 0.43 0.04 0.39 0.34 0.02 0.38
x (mm) 38.78 38.78 91.32 62.54 38.78 56.23 49.11 38.78 54.38
As (mm2) 111.56 7.09 489.13 436.90 43.99 392.83 343.07 18.85 379.90
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 156.00 156.00 156.00 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 19.3 43.5 0.4 0.7 33.0 0.6 0.9 29.9 0.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.18 0.40 0.00 0.00 0.23 0.00 0.01 0.21 0.01
x (mm) 38.78 57.82 38.78 38.78 38.78 38.78 38.78 38.78 38.78
As (mm2) 134.11 309.69 2.74 4.76 229.12 4.01 5.96 207.72 5.74
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 156.00 156.00 156.00 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 45.7 61.1 56.2 55.2 50.2 53.6
v (N/mm2) 0.57 0.76 0.54 0.53 0.48 0.51
vc (N/mm2) 0.51 0.51 0.58 0.53 0.53 0.53 0.53 0.53 0.53
v-max (N/mm2) 4.00 4.00 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 121.9 121.9
Td (kN.m) 0.0 0.0 0.2
vt (N/mm2) 0.00 0.00 0.00
vt-min(N/mm2) 0.00 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 38.59 OK 17.19 < 57.9 OK 17.19 < 57.9 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 603.19 603.19 402.12 603.19 603.19 402.12 603.19
Bot Edge 402.12 402.12 402.12 603.19 603.19 603.19 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-49

Axis: A Storey: 2 ... Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))

2B53 L=6000mm
BwxH (mm) 300 x 400
Flange BfxHf ---
C20/25 / Grade 500 (Type 2)
52.747

Shear
Force
(Envelope)
-59.314
59.314
36.286

Moment
(Envelope)
-39.171

Bending (Top Edge) ...

M (kN.m) 59.3 0.8 36.3
d (mm) 349.0 349.0 349.0
K/K' 0.42 0.01 0.25
x (mm) 60.70 38.78 38.78
As (mm2) 424.09 5.50 251.72
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Bending (Bottom Edge) ...
M (kN.m) 0.5 39.2 8.8
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.27 0.06
x (mm) 38.78 38.90 38.78
As (mm2) 3.66 271.78 61.06
As' (mm2) 0.00 0.00 0.00
As-min 156.00 156.00 156.00
Shear and Bending Design ...
Vd (kN) 59.3 52.7
v (N/mm2) 0.57 0.50
vc (N/mm2) 0.53 0.53 0.46
v-max (N/mm2) 4.00 4.00
Vnom (kN) 121.9
Td (kN.m) 0.0
vt (N/mm2) 0.00
vt-min(N/mm2) 0.00
b-sup (mm) 0.0 0.0
Links H8-250 H8-250 H8-250
Deflection Check ...
L/d 17.19 < 55.91 OK
Supplied Steel Areas (mm2)
Top Edge 603.19 402.12 402.12
Bot Edge 603.19 603.19 603.19

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-50

Axis: 6 Storey: 2 Etriyeler: C20/25 / Grade 500 (Type 2) (Links: Grade 500 (Type 2))
2B58 L=1540mm 2B57 L=2230mm
BwxH (mm) 230 x 400 230 x 400
Flange BfxHf --- ---
C20/25 / Grade 500 (Type 2) C20/25 / Grade 500 (Type 2)
35.161

12.77
Shear
Force
(Envelope)
-32.865
33.501
29.381

0.684
Moment
(Envelope) -5.017

Bending (Top Edge) ...

M (kN.m) 5.9 20.2 33.5 29.4 16.6 2.8
d (mm) 349.0 349.0 349.0 349.0 349.0 349.0
K/K' 0.05 0.18 0.31 0.27 0.15 0.03
x (mm) 38.78 38.78 43.68 38.78 38.78 38.78
As (mm2) 40.65 139.86 233.96 203.82 115.33 19.38
As' (mm2) 0.00 0.00 0.00 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Bending (Bottom Edge) ...
M (kN.m) 0.3 5.0 4.4
d (mm) 349.0 349.0 349.0
K/K' 0.00 0.05 0.04
x (mm) 38.78 38.78 38.78
As (mm2) 2.07 34.80 30.47
As' (mm2) 0.00 0.00 0.00
As-min 119.60 119.60 119.60 119.60 119.60 119.60
Shear and Bending Design ...
Vd (kN) 17.9 26.6 32.9 12.8
v (N/mm2) 0.22 0.33 0.41 0.16
vc (N/mm2) 0.51 0.51 0.51 0.51 0.51 0.51
v-max (N/mm2) 4.00 4.00 4.00 4.00
Vnom (kN) 106.3 106.3
Td (kN.m) 0.0 0.0
vt (N/mm2) 0.00 0.00
vt-min(N/mm2) 0.00 0.00
b-sup (mm) 0.0 0.0 0.0 0.0
Links H8-250 H8-250 H8-250 H8-250 H8-250 H8-250
Deflection Check ...
L/d --- 6.39 < 59.44 OK
Supplied Steel Areas (mm2)
Top Edge 402.12 402.12 402.12 402.12 402.12 402.12
Bot Edge 402.12 402.12 402.12 402.12 402.12 402.12

Project: JNHPPAdministrationBuilding175mmslabREVB
JNHPP Administration Building Ent Hall
BEAM DESIGN RESULTS Prota Structure 03.0 (04.2018) / Page: BD-51

Project: JNHPPAdministrationBuilding175mmslabREVB
 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Column Reinforcement Design

1C1 (J-1) (230/230)
(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 157.7, 274.5 -1.6, 0.0 3.7, 0.0
2 110.9, 191.5 -1.1, 0.0 2.6, 0.0
3 164.0, 280.7 -1.6, 0.0 4.5, 0.0
4 94.5, 157.7 -1.3, 0.0 1.9, 0.0
5 126.3, 223.0 -1.6, 0.0 -10.4, 0.0
6 139.9, 236.6 -1.1, 0.0 16.7, 0.0
7 140.1, 236.8 -15.0, 0.0 3.3, 0.0

8 126.1, 222.8 12.2, 0.0 3.1, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 236.6 - 236.6 kN
M11 -1.1 -2.7 0.0 kN.m
M22 16.7 2.7 18.8 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.179
=
Beta = 0.79

Vd(1/2) = 5.4 / 4.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.85 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.11 / 0.08 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C1 (J-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 70.9, 78.3 -7.2, 5.3 5.9, -5.3
2 48.7, 54.1 -5.0, 3.7 4.1, -3.7
3 73.4, 80.9 -7.3, 5.3 6.1, -5.5
4 33.0, 40.4 -3.7, 3.2 3.1, -3.1
5 57.8, 64.2 -6.0, 4.5 3.2, -3.2
6 59.1, 65.5 -5.9, 4.4 6.6, -5.7
7 59.1, 65.5 -7.6, 5.6 4.9, -4.5

8 57.8, 64.2 -4.4, 3.3 4.9, -4.5

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 65.5 - 65.5 kN
M11 -7.6 -0.8 -12.2 kN.m
M22 4.9 0.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.050
=
Beta = 0.94

Vd(1/2) = 2.9 / 3.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.83 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

v(1/2) = 0.06 / 0.06 N/mm2 Le2/b2 = 12.0 < 15.0 √

Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C2 (J-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 293.1, 409.8 -2.6, 0.0 1.6, 0.0
2 206.0, 286.6 -1.9, 0.0 1.1, 0.0
3 252.1, 368.8 -3.0, 0.0 -0.6, 0.0
4 226.0, 289.2 -1.4, 0.0 2.4, 0.0
5 249.6, 346.3 -2.4, 0.0 -13.6, 0.0
6 244.9, 341.6 -2.1, 0.0 16.4, 0.0
7 254.3, 351.0 -15.9, 0.0 1.5, 0.0

8 240.2, 337.0 11.4, 0.0 1.3, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 341.6 - 341.6 kN
M11 -2.1 -3.9 0.0 kN.m
M22 16.4 3.9 19.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.258
=
Beta = 0.70

Vd(1/2) = 0.1 / 4.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.79 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C2 (J-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 102.3, 109.8 -6.0, 5.7 -0.3, -0.2
2 70.6, 75.9 -4.1, 4.0 -0.2, -0.1
3 86.0, 93.4 -6.3, 6.1 -2.3, 1.7
4 69.2, 76.7 -3.0, 3.1 1.8, -1.9
5 84.7, 91.1 -4.9, 4.7 -2.6, 2.1
6 84.6, 91.0 -5.0, 4.9 2.1, -2.4
7 85.3, 91.7 -6.6, 6.0 -0.3, -0.2

8 84.0, 90.4 -3.3, 3.6 -0.3, -0.1

Critical Loading: 1 - (G*F)

min Design
N 109.8 - 109.8 kN
M11 -6.0 -1.3 -7.1 kN.m
M22 -0.3 -1.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.083
=
Beta = 0.90

ProtaStructure v3.0.4 Page 2

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Vd(1/2) = 0.0 / 3.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.79 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C3 (J-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 325.8, 333.3 -5.0, 0.0 -0.1, 0.0
2 228.3, 233.7 -3.5, 0.0 -0.1, 0.0
3 289.8, 297.3 -5.3, 0.0 1.0, 0.0
4 235.5, 243.0 -2.8, 0.0 -1.1, 0.0
5 273.6, 280.0 -4.3, 0.0 -15.3, 0.0
6 274.3, 280.7 -4.1, 0.0 15.2, 0.0
7 281.3, 287.7 -18.6, 0.0 0.0, 0.0

8 266.7, 273.1 10.2, 0.0 -0.2, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 287.7 - 287.7 kN
M11 -18.6 -3.3 -21.1 kN.m
M22 0.0 3.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.218
=
Beta = 0.75

Vd(1/2) = 3.6 / 4.4 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C3 (J-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 97.8, 105.3 -8.1, 9.1 0.0, 0.2
2 67.5, 72.9 -5.6, 6.3 0.0, 0.1
3 82.5, 90.0 -8.0, 9.2 2.1, -1.9
4 66.4, 73.8 -4.6, 5.2 -2.2, 2.1
5 81.1, 87.5 -6.8, 7.6 -2.3, 2.1
6 81.0, 87.4 -6.7, 7.6 2.2, -1.9
7 81.7, 88.1 -8.4, 8.8 0.0, 0.1

8 80.4, 86.8 -5.1, 6.4 0.0, 0.1

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.0 - 90.0 kN
M11 9.2 1.0 11.2 kN.m
M22 2.1 1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=

ProtaStructure v3.0.4 Page 3

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Beta = 0.92

Vd(1/2) = 1.0 / 4.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.08 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C4 (J-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 322.9, 330.4 -4.9, 0.0 0.1, 0.0
2 226.4, 231.7 -3.4, 0.0 0.1, 0.0
3 286.4, 293.9 -5.2, 0.0 -0.9, 0.0
4 234.7, 242.2 -2.7, 0.0 1.0, 0.0
5 271.7, 278.1 -4.2, 0.0 -15.2, 0.0
6 271.5, 277.9 -4.0, 0.0 15.3, 0.0
7 278.9, 285.3 -18.6, 0.0 0.2, 0.0

8 264.3, 270.7 10.3, 0.0 0.0, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 285.3 - 285.3 kN
M11 -18.6 -3.3 -21.0 kN.m
M22 0.2 3.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.216
=
Beta = 0.75

Vd(1/2) = 3.6 / 4.4 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C4 (J-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.5, 106.0 -7.9, 8.9 0.0, 0.0
2 68.0, 73.3 -5.5, 6.2 0.0, 0.0
3 83.2, 90.6 -7.9, 9.0 -2.2, 2.1
4 66.6, 74.1 -4.5, 5.0 2.2, -2.1
5 81.6, 88.0 -6.6, 7.4 -2.2, 2.0
6 81.6, 88.0 -6.6, 7.4 2.3, -2.1
7 82.3, 88.7 -8.3, 8.6 0.0, -0.1

8 80.9, 87.3 -4.9, 6.2 0.0, 0.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.6 - 90.6 kN
M11 9.0 1.0 11.0 kN.m
M22 -2.2 -1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5
0.069

ProtaStructure v3.0.4 Page 4

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

N/bhFcu
=
Beta = 0.92

Vd(1/2) = 1.0 / 4.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.08 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C5 (J-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 324.1, 331.5 -4.9, 0.0 0.1, 0.0
2 227.1, 232.5 -3.5, 0.0 0.0, 0.0
3 287.6, 295.0 -5.2, 0.0 1.1, 0.0
4 235.3, 242.8 -2.7, 0.0 -1.0, 0.0
5 272.6, 279.0 -4.2, 0.0 -15.2, 0.0
6 272.5, 278.9 -4.1, 0.0 15.3, 0.0
7 279.9, 286.3 -18.6, 0.0 0.2, 0.0

8 265.2, 271.6 10.3, 0.0 0.0, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 286.3 - 286.3 kN
M11 -18.6 -3.3 -21.1 kN.m
M22 0.2 3.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.216
=
Beta = 0.75

Vd(1/2) = 3.6 / 4.4 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C5 (J-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.4, 105.8 -7.9, 8.9 0.0, 0.0
2 67.9, 73.2 -5.5, 6.2 0.0, 0.0
3 83.0, 90.4 -7.9, 9.0 2.2, -2.1
4 66.5, 74.0 -4.5, 5.0 -2.1, 2.1
5 81.4, 87.8 -6.6, 7.4 -2.2, 2.0
6 81.4, 87.8 -6.6, 7.4 2.3, -2.1
7 82.1, 88.5 -8.3, 8.6 0.1, -0.1

8 80.8, 87.2 -4.9, 6.2 0.0, 0.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.4 - 90.4 kN
M11 9.0 1.0 11.0 kN.m
M22 2.2 1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-

ProtaStructure v3.0.4 Page 5

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 1.0 / 4.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.08 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C6 (J-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 320.3, 327.8 -4.9, 0.0 -0.1, 0.0
2 224.5, 229.8 -3.4, 0.0 0.0, 0.0
3 284.2, 291.7 -5.2, 0.0 -1.0, 0.0
4 232.7, 240.1 -2.7, 0.0 0.9, 0.0
5 269.4, 275.8 -4.2, 0.0 -15.3, 0.0
6 269.4, 275.8 -4.1, 0.0 15.2, 0.0
7 276.7, 283.1 -18.6, 0.0 0.0, 0.0

8 262.1, 268.5 10.4, 0.0 -0.1, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 283.1 - 283.1 kN
M11 -18.6 -3.3 -21.1 kN.m
M22 0.0 3.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.214
=
Beta = 0.75

Vd(1/2) = 3.6 / 4.4 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C6 (J-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 97.8, 105.3 -7.9, 8.8 -0.1, 0.1
2 67.5, 72.9 -5.5, 6.2 -0.1, 0.1
3 82.6, 90.0 -7.9, 9.1 -2.3, 2.3
4 66.3, 73.7 -4.4, 5.0 2.1, -2.0
5 81.1, 87.5 -6.6, 7.4 -2.3, 2.2
6 81.0, 87.4 -6.6, 7.4 2.2, -1.9
7 81.7, 88.1 -8.2, 8.6 0.0, 0.1

8 80.4, 86.8 -4.9, 6.2 -0.1, 0.1

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.0 - 90.0 kN
M11 9.1 1.0 11.1 kN.m
M22 -2.3 -1.0 0.0 kN.m
Nmax 529.0

ProtaStructure v3.0.4 Page 6

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Concrete Cover = 40.0 mm

BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 1.0 / 4.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.08 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C7 (J-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 341.7, 349.1 -4.9, 0.0 0.7, 0.0
2 239.4, 244.8 -3.5, 0.0 0.5, 0.0
3 302.3, 309.8 -5.2, 0.0 1.7, 0.0
4 248.7, 256.2 -2.7, 0.0 -0.5, 0.0
5 287.8, 294.2 -4.2, 0.0 -14.6, 0.0
6 286.8, 293.2 -4.2, 0.0 15.8, 0.0
7 294.6, 301.0 -18.7, 0.0 0.7, 0.0

8 280.0, 286.4 10.4, 0.0 0.5, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 301.0 - 301.0 kN
M11 -18.7 -3.5 -21.2 kN.m
M22 0.7 3.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.228
=
Beta = 0.74

Vd(1/2) = 3.8 / 4.5 kN Short Column... As (Req): %0.42 223.32 mm2

vc'(1/2) = 0.91 / 0.92 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C7 (J-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 102.8, 110.3 -8.0, 8.9 1.0, -1.2
2 71.0, 76.3 -5.5, 6.2 0.7, -0.8
3 86.6, 94.1 -8.0, 9.2 3.0, -3.1
4 69.6, 77.1 -4.4, 5.0 -1.5, 1.2
5 85.0, 91.4 -6.6, 7.5 -1.4, 1.0
6 85.3, 91.7 -6.6, 7.5 3.1, -3.0
7 85.8, 92.2 -8.3, 8.6 0.9, -1.0

8 84.5, 90.9 -5.0, 6.4 0.8, -1.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 94.1 - 94.1 kN
M11 9.2 1.1 12.1 kN.m

ProtaStructure v3.0.4 Page 7

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

M22 -3.1 -1.1 0.0 kN.m

Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.071
=
Beta = 0.91

Vd(1/2) = 1.5 / 4.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.08 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C8 (J-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 273.8, 281.3 -1.8, 0.0 -1.9, 0.0
2 191.8, 197.2 -1.2, 0.0 -1.3, 0.0
3 255.5, 263.0 -1.5, 0.0 -2.2, 0.0
4 185.9, 193.4 -1.4, 0.0 -0.8, 0.0
5 223.2, 229.6 -1.5, 0.0 -16.9, 0.0
6 237.2, 243.6 -1.5, 0.0 13.7, 0.0
7 237.7, 244.1 -16.8, 0.0 -1.5, 0.0

8 222.7, 229.1 13.8, 0.0 -1.7, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 229.6 - 229.6 kN
M11 -1.5 -2.6 0.0 kN.m
M22 -16.9 -2.6 -19.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.174
=
Beta = 0.80

Vd(1/2) = 4.0 / 4.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.89 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.08 N/mm2 Le2/b2 = 12.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C8 (J-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 82.0, 89.5 -6.1, 4.9 -3.1, 3.4
2 56.6, 61.9 -4.2, 3.4 -2.2, 2.4
3 73.9, 81.3 -5.9, 4.6 -4.1, 4.4
4 50.8, 58.3 -3.4, 3.1 -0.7, 1.1
5 67.8, 74.2 -5.0, 4.1 -4.8, 5.0
6 68.0, 74.4 -5.0, 4.1 -0.4, 0.8
7 68.7, 75.1 -7.0, 6.1 -2.6, 2.9

8 67.1, 73.5 -3.1, 2.1 -2.6, 2.9

Critical Loading: 5 - ((G+Q)P1 *F)

min Design

ProtaStructure v3.0.4 Page 8

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

N 74.2 - 74.2 kN
M11 -5.0 -0.9 -9.7 kN.m
M22 5.0 0.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.056
=
Beta = 0.93

Vd(1/2) = 2.3 / 3.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.84 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.06 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C9 (J-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 271.0, 278.4 -5.6, 0.0 1.9, 0.0
2 190.1, 195.5 -3.9, 0.0 1.3, 0.0
3 216.3, 223.8 -3.0, 0.0 2.0, 0.0
4 222.9, 230.4 -6.1, 0.0 1.1, 0.0
5 235.1, 241.5 -4.6, 0.0 -13.7, 0.0
6 221.2, 227.6 -4.7, 0.0 16.9, 0.0
7 235.5, 241.9 -19.3, 0.0 1.7, 0.0

8 220.8, 227.2 9.9, 0.0 1.5, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 241.9 - 241.9 kN
M11 -19.3 -2.8 -21.5 kN.m
M22 1.7 2.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.183
=
Beta = 0.79

Vd(1/2) = 4.0 / 4.6 kN Short Column... As (Req): %0.42 221.01 mm2

vc'(1/2) = 0.88 / 0.89 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C9 (J-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 77.0, 84.5 -8.1, 9.7 2.9, -3.3
2 53.2, 58.5 -5.7, 6.8 2.0, -2.3
3 58.4, 65.9 -4.2, 5.2 3.0, -3.4
4 58.8, 66.3 -8.6, 10.3 1.6, -1.9
5 63.8, 70.2 -6.8, 8.1 0.2, -0.7
6 63.8, 70.2 -6.8, 8.1 4.7, -4.9
7 64.5, 70.9 -8.4, 9.2 2.4, -2.8

8 63.1, 69.5 -5.2, 7.0 2.4, -2.8

ProtaStructure v3.0.4 Page 9

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 70.2 - 70.2 kN
M11 8.1 0.8 12.7 kN.m
M22 -4.9 -0.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.053
=
Beta = 0.94

Vd(1/2) = 2.3 / 4.5 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.84 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.09 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C10 (J-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 373.7, 381.1 -5.9, 0.0 0.0, 0.0
2 262.2, 267.6 -4.2, 0.0 0.0, 0.0
3 309.5, 317.0 -6.4, 0.0 -0.9, 0.0
4 295.7, 303.2 -3.2, 0.0 0.9, 0.0
5 311.8, 318.2 -4.9, 0.0 -15.4, 0.0
6 317.5, 323.9 -5.1, 0.0 15.4, 0.0
7 322.2, 328.6 -19.6, 0.0 0.1, 0.0

8 307.1, 313.5 9.6, 0.0 -0.1, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 328.6 - 328.6 kN
M11 -19.6 -3.8 -22.3 kN.m
M22 0.1 3.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.248
=
Beta = 0.71

Vd(1/2) = 3.7 / 4.7 kN Short Column... As (Req): %0.56 293.98 mm2

vc'(1/2) = 0.93 / 0.93 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C10 (J-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 104.7, 112.1 -8.4, 10.1 0.4, -0.1
2 72.2, 77.5 -5.8, 7.1 0.2, -0.1
3 68.9, 76.4 -6.0, 9.5 -1.7, 1.8
4 89.9, 97.3 -7.1, 6.7 2.2, -2.0
5 86.7, 93.1 -7.0, 8.5 -2.1, 2.1
6 86.5, 92.9 -7.0, 8.5 2.7, -2.3
7 87.4, 93.8 -8.8, 9.8 0.3, -0.1

ProtaStructure v3.0.4 Page 10

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 85.8, 92.2 -5.2, 7.2 0.3, -0.1

Critical Loading: 3 - (G+Q *F1)

min Design
N 76.4 - 76.4 kN
M11 9.5 0.9 11.2 kN.m
M22 1.8 0.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.058
=
Beta = 0.93

Vd(1/2) = 0.1 / 3.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.84 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.07 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C11 (J-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 185.2, 192.7 -3.9, 0.0 -3.8, 0.0
2 130.0, 135.3 -2.7, 0.0 -2.6, 0.0
3 110.3, 117.7 -2.4, 0.0 -2.3, 0.0
4 190.8, 198.2 -4.0, 0.0 -3.8, 0.0
5 163.3, 169.7 -3.2, 0.0 -17.8, 0.0
6 148.6, 155.0 -3.4, 0.0 11.5, 0.0
7 163.4, 169.8 -17.9, 0.0 -3.1, 0.0

8 148.5, 154.9 11.4, 0.0 -3.3, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 169.8 - 169.8 kN
M11 -17.9 -2.0 -20.6 kN.m
M22 -3.1 -2.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.128
=
Beta = 0.85

Vd(1/2) = 4.2 / 4.3 kN Short Column... As (Req): %0.52 276.33 mm2

vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C11 (J-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 59.5, 66.9 -6.8, 7.3 -6.9, 7.2
2 41.1, 46.4 -4.8, 5.1 -4.8, 5.0
3 29.4, 36.8 -3.9, 4.4 -4.0, 4.4
4 61.3, 68.7 -6.8, 7.3 -6.9, 7.2
5 50.0, 56.4 -5.7, 6.1 -7.4, 7.2
6 48.6, 55.0 -5.7, 6.1 -4.1, 4.9
7 50.0, 56.4 -7.4, 7.3 -5.7, 6.0

ProtaStructure v3.0.4 Page 11

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 48.6, 54.9 -4.0, 4.9 -5.8, 6.1

Critical Loading: 1 - (G*F)

min Design
N 66.9 - 66.9 kN
M11 7.3 0.8 14.0 kN.m
M22 7.2 0.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.051
=
Beta = 0.94

Vd(1/2) = 3.5 / 3.5 kN Short Column... As (Req): %0.45 239.91 mm2

vc'(1/2) = 0.83 / 0.83 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C12 (I-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 291.7, 299.2 -1.6, 0.0 -0.8, 0.0
2 204.1, 209.4 -1.1, 0.0 -0.5, 0.0
3 259.0, 266.5 -1.0, 0.0 -0.8, 0.0
4 209.1, 216.6 -1.4, 0.0 -0.4, 0.0
5 244.8, 251.2 -1.5, 0.0 -8.1, 0.0
6 245.1, 251.5 -1.1, 0.0 6.8, 0.0
7 242.6, 249.0 -16.4, 0.0 -0.6, 0.0

8 247.3, 253.7 13.7, 0.0 -0.7, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 249.0 - 249.0 kN
M11 -16.4 -2.9 -22.1 kN.m
M22 -0.6 -2.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.188
=
Beta = 0.78

Vd(1/2) = 1.9 / 3.9 kN Slender Column... As (Req): %0.47 250.91 mm2

vc'(1/2) = 0.89 / 0.89 N/mm2 Le1/b1 = 15.6 ≥ 15.0 As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.08 N/mm2 Le2/b2 = 14.0 < 15.0 √
Madd(1/2) = 7.0 / 0.0 kN.m 4H16
Links = H8-175

2C12 (I-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 125.3, 132.8 0.2, 1.7 4.0, -0.9
2 86.2, 91.5 0.1, 1.1 2.8, -0.7
3 109.4, 116.8 2.1, 0.0 4.3, -1.0
4 79.0, 86.4 -2.1, 2.6 1.8, -0.5
5 103.6, 110.0 0.1, 1.4 5.0, -8.0
6 103.3, 109.7 0.1, 1.4 1.7, 6.5
7 103.7, 110.1 -2.2, 3.5 3.3, -0.8

ProtaStructure v3.0.4 Page 12

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 103.2, 109.6 2.4, -0.7 3.3, -0.8

Critical Loading: 1 - (G*F)

min Design
N 132.8 - 132.8 kN
M11 1.7 1.5 0.0 kN.m
M22 4.0 1.5 5.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.100
=
Beta = 0.88

Vd(1/2) = 3.1 / 0.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.82 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.00 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C13 (I-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 468.6, 476.1 -2.0, 0.0 5.8, 0.0
2 327.8, 333.1 -1.4, 0.0 4.1, 0.0
3 402.2, 409.7 -0.8, 0.0 6.4, 0.0
4 348.0, 355.4 -2.3, 0.0 3.1, 0.0
5 386.2, 392.6 -1.9, 0.0 -9.7, 0.0
6 400.5, 406.9 -1.5, 0.0 19.5, 0.0
7 391.0, 397.4 -16.8, 0.0 5.0, 0.0

8 395.7, 402.1 13.4, 0.0 4.9, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 406.9 - 406.9 kN
M11 -1.5 -4.7 0.0 kN.m
M22 19.5 4.7 22.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.308
=
Beta = 0.64

Vd(1/2) = 4.6 / 4.0 kN Short Column... As (Req): %0.73 384.49 mm2

vc'(1/2) = 0.97 / 0.96 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.08 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C13 (I-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 155.4, 162.9 -1.7, 3.0 3.3, -7.4
2 107.2, 112.6 -1.2, 2.1 2.3, -5.2
3 118.0, 125.4 0.8, 0.5 1.9, -7.2
4 118.1, 125.6 -3.5, 4.2 3.5, -4.9
5 127.9, 134.3 -1.4, 2.5 0.9, -4.9
6 129.4, 135.8 -1.4, 2.5 4.7, -7.6
7 128.9, 135.3 -3.8, 4.7 2.8, -6.3

ProtaStructure v3.0.4 Page 13

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 128.5, 134.9 0.9, 0.3 2.8, -6.3

Critical Loading: 1 - (G*F)

min Design
N 162.9 - 162.9 kN
M11 3.0 1.9 0.0 kN.m
M22 -7.4 -1.9 -10.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.123
=
Beta = 0.85

Vd(1/2) = 2.2 / 0.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.85 / 0.80 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C14 (I-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 618.0, 625.5 -0.5, 0.0 -1.0, 0.0
2 433.0, 438.3 -0.4, 0.0 -0.7, 0.0
3 496.7, 504.2 1.1, 0.0 -2.5, 0.0
4 497.3, 504.8 -2.0, 0.0 0.9, 0.0
5 522.1, 528.5 -0.6, 0.0 -16.2, 0.0
6 517.0, 523.4 -0.3, 0.0 14.5, 0.0
7 516.9, 523.3 -15.6, 0.0 -0.8, 0.0

8 522.2, 528.6 14.7, 0.0 -0.9, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 528.5 - 528.5 kN
M11 -0.6 -6.1 0.0 kN.m
M22 -16.2 -6.1 -19.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.400
=
Beta = 0.53

Vd(1/2) = 3.9 / 3.7 kN Short Column... As (Req): %0.90 473.50 mm2

vc'(1/2) = 1.02 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C14 (I-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 140.0, 147.4 -0.6, 0.9 -0.1, 1.1
2 96.5, 101.8 -0.4, 0.6 -0.1, 0.8
3 106.9, 114.4 2.2, -2.3 0.4, 2.5
4 105.2, 112.7 -3.2, 3.8 -0.6, -0.6
5 115.8, 122.2 -0.5, 0.8 -2.6, 3.3
6 115.9, 122.3 -0.5, 0.8 2.4, -1.4
7 116.0, 122.4 -2.9, 3.0 -0.1, 0.9

ProtaStructure v3.0.4 Page 14

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 115.6, 122.0 1.9, -1.5 -0.1, 1.0

Critical Loading: 1 - (G*F)

min Design
N 147.4 - 147.4 kN
M11 0.9 1.7 3.2 kN.m
M22 1.1 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.111
=
Beta = 0.87

Vd(1/2) = 0.0 / 1.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.78 / 0.88 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C15 (I-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 595.5, 602.9 -0.5, 0.0 0.2, 0.0
2 417.1, 422.4 -0.4, 0.0 0.2, 0.0
3 477.9, 485.3 1.1, 0.0 2.0, 0.0
4 479.4, 486.8 -2.1, 0.0 -1.6, 0.0
5 500.1, 506.5 -0.6, 0.0 -15.0, 0.0
6 501.0, 507.4 -0.4, 0.0 15.4, 0.0
7 497.9, 504.3 -15.6, 0.0 0.3, 0.0

8 503.2, 509.6 14.7, 0.0 0.1, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 504.3 - 504.3 kN
M11 -15.6 -5.8 -18.8 kN.m
M22 0.3 5.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.381
=
Beta = 0.55

Vd(1/2) = 3.7 / 3.7 kN Short Column... As (Req): %0.75 395.27 mm2

vc'(1/2) = 1.01 / 1.01 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C15 (I-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 145.3, 152.8 -0.5, 0.8 -0.1, -0.2
2 100.3, 105.6 -0.4, 0.6 0.0, -0.1
3 110.7, 118.1 2.3, -2.3 -0.7, -1.6
4 110.0, 117.5 -3.2, 3.8 0.6, 1.3
5 120.4, 126.8 -0.4, 0.7 -2.4, 2.0
6 120.2, 126.6 -0.4, 0.7 2.3, -2.3
7 120.5, 126.9 -2.9, 3.0 0.0, -0.1

ProtaStructure v3.0.4 Page 15

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 120.1, 126.5 2.0, -1.6 -0.1, -0.1

Critical Loading: 1 - (G*F)

min Design
N 152.8 - 152.8 kN
M11 0.8 1.8 3.3 kN.m
M22 -0.2 -1.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.116
=
Beta = 0.86

Vd(1/2) = 0.2 / 1.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.81 / 0.88 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C16 (I-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 599.6, 607.1 -0.5, 0.0 0.0, 0.0
2 420.0, 425.4 -0.4, 0.0 0.0, 0.0
3 481.5, 489.0 1.1, 0.0 -1.7, 0.0
4 482.5, 490.0 -2.1, 0.0 1.8, 0.0
5 504.1, 510.5 -0.5, 0.0 -15.2, 0.0
6 504.0, 510.4 -0.4, 0.0 15.3, 0.0
7 501.4, 507.8 -15.7, 0.0 0.1, 0.0

8 506.7, 513.1 14.7, 0.0 0.0, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 507.8 - 507.8 kN
M11 -15.7 -5.8 -18.9 kN.m
M22 0.1 5.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.384
=
Beta = 0.55

Vd(1/2) = 3.6 / 3.7 kN Short Column... As (Req): %0.76 404.48 mm2

vc'(1/2) = 1.02 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C16 (I-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 143.3, 150.7 -0.5, 0.8 0.0, 0.0
2 98.8, 104.1 -0.3, 0.6 0.0, 0.0
3 109.1, 116.6 2.3, -2.3 0.6, 1.5
4 108.2, 115.7 -3.2, 3.8 -0.5, -1.5
5 118.5, 124.9 -0.4, 0.7 -2.4, 2.2
6 118.6, 125.0 -0.4, 0.7 2.4, -2.2
7 118.8, 125.2 -2.9, 3.0 0.0, 0.0

ProtaStructure v3.0.4 Page 16

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 118.4, 124.8 2.0, -1.6 0.0, 0.0

Critical Loading: 1 - (G*F)

min Design
N 150.7 - 150.7 kN
M11 0.8 1.7 3.2 kN.m
M22 0.0 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.114
=
Beta = 0.86

Vd(1/2) = 0.2 / 1.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.81 / 0.88 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C17 (I-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 594.0, 601.5 -0.5, 0.0 -0.1, 0.0
2 416.1, 421.5 -0.4, 0.0 -0.1, 0.0
3 477.0, 484.5 1.1, 0.0 1.7, 0.0
4 478.1, 485.6 -2.0, 0.0 -1.9, 0.0
5 499.3, 505.7 -0.5, 0.0 -15.3, 0.0
6 499.4, 505.8 -0.4, 0.0 15.1, 0.0
7 496.7, 503.1 -15.7, 0.0 0.0, 0.0

8 502.0, 508.4 14.8, 0.0 -0.2, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 503.1 - 503.1 kN
M11 -15.7 -5.8 -18.9 kN.m
M22 0.0 -5.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.380
=
Beta = 0.55

Vd(1/2) = 3.6 / 3.7 kN Short Column... As (Req): %0.75 395.56 mm2

vc'(1/2) = 1.01 / 1.01 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C17 (I-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 143.8, 151.2 -0.5, 0.8 -0.1, 0.2
2 99.2, 104.5 -0.4, 0.6 -0.1, 0.2
3 109.7, 117.2 2.3, -2.3 -0.7, -1.3
4 108.6, 116.0 -3.2, 3.7 0.5, 1.6
5 119.1, 125.5 -0.4, 0.7 -2.5, 2.4
6 118.9, 125.3 -0.4, 0.7 2.3, -2.0
7 119.2, 125.6 -2.9, 3.0 -0.1, 0.2

ProtaStructure v3.0.4 Page 17

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 118.8, 125.2 2.0, -1.6 -0.1, 0.2

Critical Loading: 1 - (G*F)

min Design
N 151.2 - 151.2 kN
M11 0.8 1.7 3.2 kN.m
M22 0.2 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.114
=
Beta = 0.86

Vd(1/2) = 0.1 / 1.6 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.80 / 0.88 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C18 (I-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 623.8, 631.3 -0.5, 0.0 1.1, 0.0
2 437.0, 442.3 -0.4, 0.0 0.8, 0.0
3 500.9, 508.4 1.1, 0.0 -0.8, 0.0
4 501.6, 509.1 -2.0, 0.0 2.6, 0.0
5 524.9, 531.3 -0.5, 0.0 -14.3, 0.0
6 523.8, 530.2 -0.5, 0.0 16.1, 0.0
7 521.7, 528.1 -15.7, 0.0 1.0, 0.0

8 527.0, 533.4 14.8, 0.0 0.9, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 530.2 - 530.2 kN
M11 -0.5 -6.1 0.0 kN.m
M22 16.1 6.1 19.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.401
=
Beta = 0.53

Vd(1/2) = 3.8 / 3.7 kN Short Column... As (Req): %0.90 475.30 mm2

vc'(1/2) = 1.03 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C18 (I-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 147.4, 154.9 -0.5, 0.8 1.2, -1.7
2 101.6, 107.0 -0.4, 0.6 0.8, -1.2
3 111.4, 118.8 2.2, -2.2 1.4, 0.2
4 112.1, 119.6 -3.1, 3.7 0.4, -2.8
5 121.9, 128.3 -0.4, 0.7 -1.4, 0.8
6 122.1, 128.5 -0.4, 0.7 3.4, -3.6
7 122.2, 128.6 -2.8, 2.9 1.0, -1.4

ProtaStructure v3.0.4 Page 18

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 121.7, 128.1 2.0, -1.5 1.0, -1.4

Critical Loading: 1 - (G*F)

min Design
N 154.9 - 154.9 kN
M11 0.8 1.8 3.3 kN.m
M22 -1.7 -1.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.117
=
Beta = 0.86

Vd(1/2) = 0.3 / 1.6 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.82 / 0.88 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C19 (I-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 504.7, 512.2 -0.2, 0.0 -3.0, 0.0
2 353.3, 358.6 -0.1, 0.0 -2.1, 0.0
3 396.5, 404.0 0.2, 0.0 -1.4, 0.0
4 412.9, 420.3 -0.5, 0.0 -3.5, 0.0
5 416.6, 423.0 -0.1, 0.0 -17.8, 0.0
6 431.3, 437.7 -0.2, 0.0 12.7, 0.0
7 422.1, 428.5 -15.7, 0.0 -2.5, 0.0

8 425.7, 432.1 15.4, 0.0 -2.6, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 423.0 - 423.0 kN
M11 -0.1 -4.9 0.0 kN.m
M22 -17.8 -4.9 -20.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.320
=
Beta = 0.63

Vd(1/2) = 4.2 / 3.7 kN Short Column... As (Req): %0.62 330.49 mm2

vc'(1/2) = 0.98 / 0.98 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 12.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C19 (I-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 128.2, 135.6 -0.2, 0.4 -4.1, 5.1
2 88.4, 93.7 -0.1, 0.3 -2.8, 3.6
3 105.6, 113.0 1.4, -0.8 -3.6, 3.3
4 89.0, 96.4 -1.8, 1.4 -2.8, 4.8
5 105.9, 112.3 -0.2, 0.3 -5.8, 6.5
6 106.3, 112.7 -0.1, 0.3 -1.0, 2.0
7 105.9, 112.3 -2.5, 2.7 -3.4, 4.3

ProtaStructure v3.0.4 Page 19

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 106.3, 112.7 2.2, -2.1 -3.4, 4.3

Critical Loading: 1 - (G*F)

min Design
N 135.6 - 135.6 kN
M11 0.4 1.6 0.0 kN.m
M22 5.1 1.6 6.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.103
=
Beta = 0.88

Vd(1/2) = 1.8 / 0.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.85 / 0.85 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C20 (I-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 485.8, 493.3 0.9, 0.0 2.7, 0.0
2 340.3, 345.6 0.7, 0.0 1.9, 0.0
3 381.9, 389.4 -0.8, 0.0 1.4, 0.0
4 399.5, 406.9 2.4, 0.0 3.1, 0.0
5 415.3, 421.7 0.8, 0.0 -13.0, 0.0
6 401.4, 407.8 0.7, 0.0 17.6, 0.0
7 405.7, 412.1 -14.5, 0.0 2.4, 0.0

8 411.0, 417.4 16.1, 0.0 2.3, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 407.8 - 407.8 kN
M11 0.7 4.7 0.0 kN.m
M22 17.6 4.7 20.6 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.308
=
Beta = 0.64

Vd(1/2) = 4.2 / 3.8 kN Short Column... As (Req): %0.55 291.40 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C20 (I-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 120.3, 127.7 0.8, -1.2 3.4, -4.4
2 83.0, 88.3 0.6, -0.9 2.3, -3.1
3 97.5, 105.0 -2.0, 2.0 2.9, -2.8
4 85.0, 92.5 3.2, -4.0 2.4, -4.3
5 99.6, 106.0 0.7, -1.0 0.4, -1.5
6 99.5, 105.9 0.7, -1.0 5.2, -5.9
7 99.5, 105.9 -1.6, 1.1 2.8, -3.7

ProtaStructure v3.0.4 Page 20

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 99.6, 106.0 2.9, -3.2 2.8, -3.7

Critical Loading: 1 - (G*F)

min Design
N 127.7 - 127.7 kN
M11 -1.2 -1.5 0.0 kN.m
M22 -4.4 -1.5 -5.7 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.097
=
Beta = 0.88

Vd(1/2) = 2.6 / 1.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.03 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C21 (I-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 617.9, 625.4 0.9, 0.0 -0.4, 0.0
2 432.9, 438.2 0.6, 0.0 -0.3, 0.0
3 494.8, 502.3 2.5, 0.0 1.3, 0.0
4 498.7, 506.1 -1.0, 0.0 -1.9, 0.0
5 516.6, 523.0 0.9, 0.0 -15.6, 0.0
6 522.3, 528.7 0.7, 0.0 15.0, 0.0
7 516.6, 523.0 -14.6, 0.0 -0.2, 0.0

8 522.3, 528.7 16.1, 0.0 -0.4, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 528.7 - 528.7 kN
M11 16.1 6.1 19.4 kN.m
M22 -0.4 -6.1 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.400
=
Beta = 0.53

Vd(1/2) = 3.7 / 3.8 kN Short Column... As (Req): %0.89 471.78 mm2

vc'(1/2) = 1.02 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C21 (I-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 144.6, 152.0 0.8, -1.3 0.1, 0.3
2 99.6, 105.0 0.5, -0.9 0.0, 0.3
3 108.1, 115.6 -0.1, -2.4 -0.5, -0.9
4 110.7, 118.2 1.3, 0.4 0.5, 1.6
5 119.6, 126.0 0.6, -1.1 -2.5, 2.7
6 119.5, 125.9 0.6, -1.1 2.5, -2.0
7 119.4, 125.8 -1.9, 1.3 0.0, 0.3

ProtaStructure v3.0.4 Page 21

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 119.7, 126.1 3.1, -3.5 0.0, 0.3

Critical Loading: 1 - (G*F)

min Design
N 152.0 - 152.0 kN
M11 -1.3 -1.7 -3.3 kN.m
M22 0.3 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.115
=
Beta = 0.86

Vd(1/2) = 0.1 / 0.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.80 / 0.82 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C22 (I-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 343.6, 351.0 0.6, 0.0 -5.0, 0.0
2 240.8, 246.1 0.4, 0.0 -3.5, 0.0
3 284.7, 292.2 -0.5, 0.0 -5.4, 0.0
4 269.6, 277.1 1.5, 0.0 -2.6, 0.0
5 296.5, 302.9 0.7, 0.0 -18.8, 0.0
6 281.5, 287.9 0.4, 0.0 10.4, 0.0
7 286.1, 292.5 -14.9, 0.0 -4.1, 0.0

8 291.8, 298.2 15.9, 0.0 -4.2, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 302.9 - 302.9 kN
M11 0.7 3.5 0.0 kN.m
M22 -18.8 -3.5 -21.3 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.229
=
Beta = 0.74

Vd(1/2) = 4.5 / 3.8 kN Short Column... As (Req): %0.43 228.94 mm2

vc'(1/2) = 0.92 / 0.92 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.08 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C22 (I-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 103.6, 111.0 0.8, -1.0 -8.0, 9.0
2 71.5, 76.8 0.6, -0.7 -5.6, 6.3
3 69.8, 77.3 -1.5, 1.3 -5.6, 8.3
4 87.5, 94.9 2.8, -2.9 -6.9, 6.0
5 86.5, 92.9 0.7, -0.9 -8.5, 8.8
6 85.0, 91.4 0.7, -0.8 -4.9, 6.3
7 85.6, 92.0 -1.7, 1.4 -6.7, 7.5

ProtaStructure v3.0.4 Page 22

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 85.9, 92.3 3.1, -3.1 -6.7, 7.5

Critical Loading: 3 - (G+Q *F1)

min Design
N 77.3 - 77.3 kN
M11 -1.5 -0.9 0.0 kN.m
M22 8.3 0.9 9.7 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.058
=
Beta = 0.93

Vd(1/2) = 3.3 / 0.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.01 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C23 (H-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 308.4, 315.9 2.9, 0.0 5.3, 0.0
2 215.6, 221.0 2.0, 0.0 3.7, 0.0
3 272.4, 279.8 2.4, 0.0 5.6, 0.0
4 221.2, 228.7 2.2, 0.0 2.9, 0.0
5 251.9, 258.3 2.3, 0.0 -10.1, 0.0
6 265.6, 272.0 2.7, 0.0 19.0, 0.0
7 269.4, 275.8 -12.6, 0.0 4.5, 0.0

8 248.1, 254.5 17.5, 0.0 4.4, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 272.0 - 272.0 kN
M11 2.7 3.1 0.0 kN.m
M22 19.0 3.1 21.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.206
=
Beta = 0.76

Vd(1/2) = 4.5 / 4.2 kN Short Column... As (Req): %0.42 221.37 mm2

vc'(1/2) = 0.90 / 0.90 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.08 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C23 (H-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 73.9, 81.3 3.8, -4.7 7.8, -9.0
2 51.0, 56.3 2.6, -3.3 5.4, -6.3
3 55.6, 63.1 2.3, -3.5 8.0, -9.4
4 56.6, 64.1 3.6, -3.9 4.1, -4.9
5 60.6, 67.0 3.2, -3.9 4.8, -6.4
6 61.7, 68.1 3.1, -3.9 8.2, -8.7
7 61.4, 67.8 1.0, -1.9 6.5, -7.6

ProtaStructure v3.0.4 Page 23

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 60.9, 67.3 5.3, -5.9 6.5, -7.6

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 67.3 - 67.3 kN
M11 -5.9 -0.8 0.0 kN.m
M22 -7.6 -0.8 -13.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.051
=
Beta = 0.94

Vd(1/2) = 4.1 / 2.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.84 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.05 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C24 (H-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 522.8, 530.3 3.9, 0.0 -0.5, 0.0
2 365.5, 370.8 2.7, 0.0 -0.4, 0.0
3 409.1, 416.6 2.9, 0.0 -2.0, 0.0
4 425.5, 432.9 3.2, 0.0 1.2, 0.0
5 440.9, 447.3 3.0, 0.0 -15.7, 0.0
6 436.2, 442.6 3.4, 0.0 14.9, 0.0
7 449.3, 455.7 -11.8, 0.0 -0.4, 0.0

8 427.8, 434.2 18.3, 0.0 -0.5, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 434.2 - 434.2 kN
M11 18.3 5.0 21.4 kN.m
M22 -0.5 -5.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.328
=
Beta = 0.62

Vd(1/2) = 3.7 / 4.4 kN Short Column... As (Req): %0.71 374.05 mm2

vc'(1/2) = 0.99 / 0.98 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C24 (H-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 115.6, 123.1 4.9, -6.2 -0.7, 1.0
2 79.6, 85.0 3.4, -4.3 -0.5, 0.7
3 80.4, 87.9 3.2, -4.4 -3.2, 3.7
4 94.3, 101.8 4.6, -5.3 2.1, -2.2
5 95.5, 101.9 4.1, -5.1 -2.9, 3.0
6 95.7, 102.1 4.2, -5.2 1.7, -1.4
7 95.8, 102.2 1.9, -3.1 -0.6, 0.8

ProtaStructure v3.0.4 Page 24

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 95.3, 101.7 6.3, -7.3 -0.6, 0.8

Critical Loading: 1 - (G*F)

min Design
N 123.1 - 123.1 kN
M11 -6.2 -1.4 -7.4 kN.m
M22 1.0 1.4 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.093
=
Beta = 0.89

Vd(1/2) = 1.6 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C25 (H-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 483.6, 491.0 3.3, 0.0 0.1, 0.0
2 338.8, 344.1 2.3, 0.0 0.1, 0.0
3 360.8, 368.3 1.8, 0.0 1.7, 0.0
4 417.3, 424.8 3.5, 0.0 -1.5, 0.0
5 406.3, 412.7 2.6, 0.0 -15.1, 0.0
6 406.8, 413.2 2.9, 0.0 15.2, 0.0
7 417.4, 423.8 -12.3, 0.0 0.1, 0.0

8 395.6, 402.0 17.9, 0.0 0.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 402.0 - 402.0 kN
M11 17.9 4.6 20.8 kN.m
M22 0.1 4.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.304
=
Beta = 0.65

Vd(1/2) = 3.6 / 4.3 kN Short Column... As (Req): %0.56 295.05 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C25 (H-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.8, 124.2 5.0, -5.7 -0.1, 0.0
2 80.5, 85.8 3.5, -4.0 -0.1, 0.0
3 82.6, 90.1 2.8, -3.3 2.3, -2.7
4 94.2, 101.6 5.2, -5.9 -2.5, 2.8
5 96.7, 103.1 4.2, -4.8 -2.3, 2.0
6 96.5, 102.9 4.2, -4.8 2.2, -2.0
7 96.9, 103.3 2.0, -2.7 -0.1, 0.0

ProtaStructure v3.0.4 Page 25

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 96.3, 102.7 6.5, -6.9 -0.1, 0.0

Critical Loading: 1 - (G*F)

min Design
N 124.2 - 124.2 kN
M11 -5.7 -1.4 -7.0 kN.m
M22 -0.1 -1.4 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 1.2 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C26 (H-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 484.0, 491.5 3.2, 0.0 0.0, 0.0
2 339.1, 344.4 2.3, 0.0 0.0, 0.0
3 360.4, 367.8 1.8, 0.0 -1.5, 0.0
4 418.5, 426.0 3.5, 0.0 1.6, 0.0
5 407.0, 413.4 2.6, 0.0 -15.1, 0.0
6 406.8, 413.2 2.8, 0.0 15.2, 0.0
7 417.8, 424.2 -12.4, 0.0 0.1, 0.0

8 396.0, 402.4 17.9, 0.0 0.0, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 402.4 - 402.4 kN
M11 17.9 4.6 20.8 kN.m
M22 0.0 4.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.304
=
Beta = 0.64

Vd(1/2) = 3.6 / 4.3 kN Short Column... As (Req): %0.56 295.27 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C26 (H-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.3, 123.7 5.0, -5.7 0.0, 0.1
2 80.1, 85.5 3.5, -4.0 0.0, 0.0
3 82.1, 89.6 2.8, -3.3 -2.5, 2.9
4 93.9, 101.4 5.2, -5.9 2.5, -2.8
5 96.1, 102.5 4.2, -4.8 -2.3, 2.1
6 96.2, 102.6 4.2, -4.8 2.2, -2.0
7 96.5, 102.9 1.9, -2.6 0.0, 0.0

ProtaStructure v3.0.4 Page 26

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 95.9, 102.3 6.5, -6.9 0.0, 0.1

Critical Loading: 1 - (G*F)

min Design
N 123.7 - 123.7 kN
M11 -5.7 -1.4 -7.0 kN.m
M22 0.1 1.4 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 1.3 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C27 (H-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 484.6, 492.0 3.2, 0.0 0.1, 0.0
2 339.5, 344.8 2.3, 0.0 0.1, 0.0
3 361.1, 368.5 1.8, 0.0 1.7, 0.0
4 418.6, 426.1 3.5, 0.0 -1.6, 0.0
5 407.4, 413.8 2.7, 0.0 -15.1, 0.0
6 407.3, 413.7 2.8, 0.0 15.2, 0.0
7 418.3, 424.7 -12.4, 0.0 0.1, 0.0

8 396.4, 402.8 17.9, 0.0 0.0, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 402.8 - 402.8 kN
M11 17.9 4.6 20.9 kN.m
M22 0.0 4.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.305
=
Beta = 0.64

Vd(1/2) = 3.6 / 4.3 kN Short Column... As (Req): %0.56 298.09 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C27 (H-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.3, 123.7 5.0, -5.7 0.0, 0.0
2 80.1, 85.5 3.5, -4.0 0.0, 0.0
3 82.1, 89.6 2.8, -3.3 2.4, -2.8
4 93.8, 101.3 5.2, -5.9 -2.5, 2.8
5 96.1, 102.5 4.2, -4.8 -2.3, 2.0
6 96.2, 102.6 4.2, -4.8 2.2, -2.0
7 96.4, 102.8 2.0, -2.7 0.0, 0.0

ProtaStructure v3.0.4 Page 27

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 95.9, 102.3 6.5, -7.0 0.0, 0.0

Critical Loading: 1 - (G*F)

min Design
N 123.7 - 123.7 kN
M11 -5.7 -1.4 -7.0 kN.m
M22 0.0 -1.4 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 1.3 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C28 (H-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 480.4, 487.8 3.3, 0.0 -0.1, 0.0
2 336.6, 341.9 2.3, 0.0 -0.1, 0.0
3 357.6, 365.1 1.8, 0.0 -1.6, 0.0
4 415.4, 422.9 3.5, 0.0 1.5, 0.0
5 403.9, 410.3 2.7, 0.0 -15.3, 0.0
6 403.9, 410.3 2.8, 0.0 15.1, 0.0
7 414.9, 421.3 -12.4, 0.0 0.0, 0.0

8 392.9, 399.3 17.9, 0.0 -0.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 399.3 - 399.3 kN
M11 17.9 4.6 20.9 kN.m
M22 -0.1 -4.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.302
=
Beta = 0.65

Vd(1/2) = 3.6 / 4.3 kN Short Column... As (Req): %0.56 294.23 mm2

vc'(1/2) = 0.97 / 0.96 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C28 (H-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.2, 123.7 5.1, -5.7 -0.1, 0.2
2 80.1, 85.5 3.5, -4.0 -0.1, 0.1
3 82.1, 89.6 2.8, -3.3 -2.6, 3.0
4 93.9, 101.4 5.3, -6.0 2.4, -2.7
5 96.2, 102.6 4.2, -4.8 -2.3, 2.2
6 96.1, 102.5 4.3, -4.8 2.2, -1.9
7 96.4, 102.8 2.0, -2.7 -0.1, 0.2

ProtaStructure v3.0.4 Page 28

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 95.9, 102.3 6.5, -7.0 -0.1, 0.2

Critical Loading: 1 - (G*F)

min Design
N 123.7 - 123.7 kN
M11 -5.7 -1.4 -7.0 kN.m
M22 0.2 1.4 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 1.3 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C29 (H-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 506.0, 513.4 3.2, 0.0 0.9, 0.0
2 354.4, 359.8 2.3, 0.0 0.6, 0.0
3 377.3, 384.8 1.8, 0.0 2.4, 0.0
4 436.5, 443.9 3.5, 0.0 -0.9, 0.0
5 425.8, 432.2 2.7, 0.0 -14.4, 0.0
6 424.9, 431.3 2.7, 0.0 15.9, 0.0
7 436.2, 442.6 -12.5, 0.0 0.8, 0.0

8 414.4, 420.8 17.9, 0.0 0.7, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 420.8 - 420.8 kN
M11 17.9 4.8 21.0 kN.m
M22 0.7 4.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.318
=
Beta = 0.63

Vd(1/2) = 3.8 / 4.3 kN Short Column... As (Req): %0.63 332.38 mm2

vc'(1/2) = 0.98 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C29 (H-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 119.7, 127.1 4.9, -5.6 0.8, -1.2
2 82.4, 87.8 3.4, -3.9 0.6, -0.9
3 84.5, 91.9 2.6, -3.0 3.1, -3.8
4 96.4, 103.9 5.3, -6.0 -1.9, 1.9
5 98.8, 105.2 4.1, -4.7 -1.6, 1.0
6 99.1, 105.5 4.1, -4.7 2.9, -3.0
7 99.2, 105.6 1.9, -2.6 0.7, -1.0

ProtaStructure v3.0.4 Page 29

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 98.7, 105.1 6.3, -6.8 0.7, -1.1

Critical Loading: 1 - (G*F)

min Design
N 127.1 - 127.1 kN
M11 -5.6 -1.5 -6.9 kN.m
M22 -1.2 -1.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.096
=
Beta = 0.88

Vd(1/2) = 1.7 / 3.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.87 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C30 (H-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 383.2, 390.7 1.4, 0.0 -2.4, 0.0
2 268.2, 273.5 1.0, 0.0 -1.7, 0.0
3 308.2, 315.7 0.9, 0.0 -2.7, 0.0
4 306.8, 314.3 1.4, 0.0 -1.2, 0.0
5 317.7, 324.1 1.2, 0.0 -17.3, 0.0
6 326.0, 332.4 1.2, 0.0 13.2, 0.0
7 326.8, 333.2 -14.3, 0.0 -2.0, 0.0

8 316.9, 323.3 16.7, 0.0 -2.0, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 324.1 - 324.1 kN
M11 1.2 3.7 0.0 kN.m
M22 -17.3 -3.7 -20.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.245
=
Beta = 0.72

Vd(1/2) = 4.1 / 4.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.93 / 0.93 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.08 N/mm2 Le2/b2 = 12.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C30 (H-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 102.3, 109.7 3.6, -3.1 -3.0, 4.0
2 70.5, 75.8 2.5, -2.2 -2.1, 2.8
3 77.7, 85.2 1.7, -1.7 -3.5, 4.5
4 77.4, 84.9 3.9, -3.3 -1.2, 1.9
5 85.0, 91.4 2.9, -2.5 -4.8, 5.5
6 84.3, 90.7 3.1, -2.7 -0.3, 1.2
7 84.9, 91.3 0.7, -0.3 -2.6, 3.4

ProtaStructure v3.0.4 Page 30

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 84.3, 90.7 5.3, -5.0 -2.5, 3.3

Critical Loading: 1 - (G*F)

min Design
N 109.7 - 109.7 kN
M11 3.6 1.3 0.0 kN.m
M22 4.0 1.3 7.2 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.083
=
Beta = 0.90

Vd(1/2) = 2.4 / 2.5 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.05 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C31 (H-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 448.2, 455.6 -0.1, 0.0 3.1, 0.0
2 314.0, 319.3 -0.1, 0.0 2.2, 0.0
3 377.6, 385.1 1.6, 0.0 3.5, 0.0
4 343.8, 351.3 -1.8, 0.0 1.6, 0.0
5 384.3, 390.7 -0.1, 0.0 -12.6, 0.0
6 369.3, 375.7 -0.1, 0.0 17.9, 0.0
7 377.7, 384.1 -15.3, 0.0 2.7, 0.0

8 375.9, 382.3 15.1, 0.0 2.6, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 375.7 - 375.7 kN
M11 -0.1 -4.3 0.0 kN.m
M22 17.9 4.3 20.8 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.284
=
Beta = 0.67

Vd(1/2) = 4.3 / 3.6 kN Short Column... As (Req): %0.48 256.37 mm2

vc'(1/2) = 0.95 / 0.96 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C31 (H-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 111.7, 119.1 -0.2, 0.3 4.3, -5.2
2 77.0, 82.3 -0.1, 0.2 3.0, -3.7
3 87.8, 95.2 2.4, -2.6 4.9, -5.8
4 81.7, 89.2 -2.6, 3.1 2.0, -2.6
5 92.6, 99.0 -0.1, 0.3 1.3, -2.3
6 92.2, 98.6 -0.1, 0.2 5.9, -6.5
7 92.5, 98.9 -2.3, 2.2 3.6, -4.4

ProtaStructure v3.0.4 Page 31

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 92.3, 98.7 2.0, -1.7 3.7, -4.4

Critical Loading: 1 - (G*F)

min Design
N 119.1 - 119.1 kN
M11 0.3 1.4 0.0 kN.m
M22 -5.2 -1.4 -6.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.090
=
Beta = 0.89

Vd(1/2) = 3.0 / 1.4 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.03 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C32 (H-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 592.3, 599.8 -0.1, 0.0 -0.4, 0.0
2 414.9, 420.3 -0.1, 0.0 -0.3, 0.0
3 476.3, 483.8 -1.8, 0.0 -1.8, 0.0
4 476.0, 483.4 1.6, 0.0 1.1, 0.0
5 495.0, 501.4 0.0, 0.0 -15.7, 0.0
6 500.8, 507.2 -0.2, 0.0 14.9, 0.0
7 498.3, 504.7 -15.3, 0.0 -0.3, 0.0

8 497.5, 503.9 15.1, 0.0 -0.4, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 501.4 - 501.4 kN
M11 0.0 -5.8 0.0 kN.m
M22 -15.7 -5.8 -18.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.379
=
Beta = 0.56

Vd(1/2) = 3.7 / 3.6 kN Short Column... As (Req): %0.74 390.38 mm2

vc'(1/2) = 1.01 / 1.01 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C32 (H-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 142.4, 149.8 0.0, 0.2 -0.2, 0.5
2 98.2, 103.5 0.0, 0.1 -0.1, 0.4
3 107.2, 114.7 0.5, 1.7 -2.6, 3.2
4 108.8, 116.2 -0.5, -1.4 2.2, -2.2
5 117.9, 124.3 0.0, 0.1 -2.5, 2.7
6 117.8, 124.2 0.0, 0.1 2.2, -1.7
7 117.7, 124.1 -2.4, 2.3 -0.1, 0.5

ProtaStructure v3.0.4 Page 32

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 117.9, 124.3 2.4, -2.1 -0.2, 0.5

Critical Loading: 1 - (G*F)

min Design
N 149.8 - 149.8 kN
M11 0.2 1.7 3.2 kN.m
M22 0.5 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.113
=
Beta = 0.87

Vd(1/2) = 0.1 / 0.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.81 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C33 (H-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 321.7, 329.1 0.0, 0.0 -4.9, 0.0
2 225.4, 230.8 0.0, 0.0 -3.5, 0.0
3 236.6, 244.0 1.0, 0.0 -2.6, 0.0
4 282.4, 289.9 -1.1, 0.0 -5.3, 0.0
5 277.9, 284.3 0.1, 0.0 -18.7, 0.0
6 263.2, 269.6 -0.2, 0.0 10.4, 0.0
7 271.0, 277.4 -15.3, 0.0 -4.1, 0.0

8 270.1, 276.5 15.2, 0.0 -4.2, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 284.3 - 284.3 kN
M11 0.1 3.3 0.0 kN.m
M22 -18.7 -3.3 -21.2 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.215
=
Beta = 0.75

Vd(1/2) = 4.5 / 3.6 kN Short Column... As (Req): %0.40 213.72 mm2

vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C33 (H-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.4, 105.9 0.0, 0.1 -8.0, 8.9
2 67.9, 73.3 0.0, 0.0 -5.6, 6.2
3 67.8, 75.3 2.0, -1.9 -4.3, 4.8
4 81.9, 89.4 -2.0, 2.1 -8.2, 9.3
5 82.2, 88.6 0.0, 0.0 -8.3, 8.6
6 80.8, 87.2 0.0, 0.1 -5.0, 6.4
7 81.5, 87.9 -2.3, 2.1 -6.7, 7.5

ProtaStructure v3.0.4 Page 33

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 81.5, 87.9 2.3, -2.0 -6.7, 7.5

Critical Loading: 4 - (G+Q)

min Design
N 89.4 - 89.4 kN
M11 2.1 1.0 0.0 kN.m
M22 9.3 1.0 11.2 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 4.2 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.82 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.00 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C34 (G-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 112.5, 120.0 1.1, 0.0 3.6, 0.0
2 79.0, 84.3 0.7, 0.0 2.6, 0.0
3 121.9, 129.4 0.9, 0.0 3.8, 0.0
4 62.1, 69.6 0.8, 0.0 2.1, 0.0
5 87.1, 93.5 0.7, 0.0 -11.5, 0.0
6 102.5, 108.9 1.1, 0.0 17.6, 0.0
7 79.6, 86.0 -13.7, 0.0 3.1, 0.0

8 110.1, 116.5 15.5, 0.0 3.1, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 108.9 - 108.9 kN
M11 1.1 1.3 0.0 kN.m
M22 17.6 1.3 18.8 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.082
=
Beta = 0.90

Vd(1/2) = 4.2 / 3.3 kN Short Column... As (Req): %0.62 326.39 mm2

vc'(1/2) = 0.83 / 0.82 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C34 (G-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 44.3, 51.8 2.9, -2.4 6.5, -6.8
2 30.6, 36.0 2.0, -1.6 4.5, -4.8
3 48.6, 56.0 2.6, -2.1 6.8, -7.1
4 19.1, 26.5 1.9, -1.6 3.4, -3.8
5 36.0, 42.4 2.4, -2.0 3.8, -4.6
6 37.5, 43.9 2.4, -2.0 7.1, -6.8
7 35.7, 42.1 0.8, -0.6 5.5, -5.7

ProtaStructure v3.0.4 Page 34

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 37.8, 44.2 4.0, -3.3 5.5, -5.7

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 44.2 - 44.2 kN
M11 4.0 0.5 0.0 kN.m
M22 -5.7 -0.5 -9.6 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.033
=
Beta = 0.96

Vd(1/2) = 3.3 / 1.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.81 / 0.81 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.04 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C35 (G-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 250.6, 258.1 1.5, 0.0 -0.5, 0.0
2 175.7, 181.0 1.0, 0.0 -0.3, 0.0
3 213.3, 220.7 1.2, 0.0 -1.3, 0.0
4 191.6, 199.1 1.2, 0.0 0.5, 0.0
5 213.7, 220.1 1.1, 0.0 -15.7, 0.0
6 207.9, 214.3 1.4, 0.0 14.9, 0.0
7 195.4, 201.8 -13.4, 0.0 -0.4, 0.0

8 226.2, 232.6 15.9, 0.0 -0.4, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 220.1 - 220.1 kN
M11 1.1 2.5 0.0 kN.m
M22 -15.7 -2.5 -17.7 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.166
=
Beta = 0.81

Vd(1/2) = 3.7 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.89 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C35 (G-2) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 89.6, 97.1 3.9, -3.3 -0.9, 1.0
2 61.8, 67.2 2.7, -2.3 -0.6, 0.7
3 73.5, 80.9 3.2, -2.8 -2.8, 2.8
4 62.8, 70.3 2.8, -2.4 1.5, -1.2
5 74.4, 80.8 3.2, -2.7 -3.0, 3.0
6 74.0, 80.4 3.2, -2.7 1.6, -1.3
7 73.1, 79.5 1.5, -1.3 -0.7, 0.8

ProtaStructure v3.0.4 Page 35

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 75.3, 81.7 4.9, -4.2 -0.7, 0.8

Critical Loading: 1 - (G*F)

min Design
N 97.1 - 97.1 kN
M11 3.9 1.1 4.9 kN.m
M22 1.0 1.1 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.073
=
Beta = 0.91

Vd(1/2) = 1.4 / 2.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.85 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C36 (G-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 232.8, 240.3 1.5, 0.0 0.1, 0.0
2 163.0, 168.4 1.1, 0.0 0.1, 0.0
3 203.6, 211.0 1.2, 0.0 1.1, 0.0
4 171.7, 179.1 1.2, 0.0 -0.9, 0.0
5 195.0, 201.4 1.1, 0.0 -15.0, 0.0
6 196.3, 202.7 1.4, 0.0 15.3, 0.0
7 180.1, 186.5 -13.4, 0.0 0.1, 0.0

8 211.2, 217.6 15.9, 0.0 0.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 217.6 - 217.6 kN
M11 15.9 2.5 18.0 kN.m
M22 0.1 2.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.165
=
Beta = 0.81

Vd(1/2) = 3.6 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C36 (G-3) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 81.7, 89.2 3.7, -3.3 0.0, -0.1
2 56.4, 61.8 2.6, -2.3 0.0, -0.1
3 67.0, 74.4 2.9, -2.7 2.2, -2.1
4 57.7, 65.2 2.9, -2.5 -2.1, 2.0
5 67.8, 74.2 3.1, -2.7 -2.2, 1.9
6 67.7, 74.1 3.1, -2.7 2.2, -2.0
7 66.6, 73.0 1.3, -1.2 0.0, -0.1

ProtaStructure v3.0.4 Page 36

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 68.9, 75.3 4.8, -4.2 0.0, -0.1

Critical Loading: 1 - (G*F)

min Design
N 89.2 - 89.2 kN
M11 3.7 1.0 4.6 kN.m
M22 -0.1 -1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.067
=
Beta = 0.92

Vd(1/2) = 1.0 / 2.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C37 (G-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 236.0, 243.5 1.5, 0.0 0.0, 0.0
2 165.3, 170.6 1.0, 0.0 0.0, 0.0
3 206.4, 213.9 1.2, 0.0 -0.9, 0.0
4 174.0, 181.5 1.2, 0.0 1.0, 0.0
5 198.3, 204.7 1.2, 0.0 -15.1, 0.0
6 198.3, 204.7 1.4, 0.0 15.2, 0.0
7 182.7, 189.1 -13.5, 0.0 0.0, 0.0

8 213.9, 220.3 16.0, 0.0 0.0, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 220.3 - 220.3 kN
M11 16.0 2.5 18.0 kN.m
M22 0.0 2.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.167
=
Beta = 0.81

Vd(1/2) = 3.6 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C37 (G-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 82.3, 89.7 3.7, -3.3 0.0, 0.1
2 56.8, 62.1 2.6, -2.3 0.0, 0.0
3 67.4, 74.9 3.0, -2.8 -2.2, 2.1
4 57.9, 65.4 2.9, -2.5 2.1, -2.0
5 68.1, 74.5 3.1, -2.8 -2.2, 2.1
6 68.2, 74.6 3.1, -2.8 2.2, -1.9
7 67.0, 73.4 1.3, -1.3 0.0, 0.1

ProtaStructure v3.0.4 Page 37

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 69.3, 75.7 4.9, -4.3 0.0, 0.1

Critical Loading: 1 - (G*F)

min Design
N 89.7 - 89.7 kN
M11 3.7 1.0 4.7 kN.m
M22 0.1 1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 1.0 / 2.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C38 (G-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 236.6, 244.1 1.5, 0.0 0.1, 0.0
2 165.7, 171.0 1.0, 0.0 0.1, 0.0
3 206.9, 214.4 1.2, 0.0 1.1, 0.0
4 174.4, 181.9 1.2, 0.0 -0.9, 0.0
5 198.7, 205.1 1.2, 0.0 -15.1, 0.0
6 199.0, 205.4 1.3, 0.0 15.2, 0.0
7 183.2, 189.6 -13.5, 0.0 0.1, 0.0

8 214.4, 220.8 16.0, 0.0 0.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 220.8 - 220.8 kN
M11 16.0 2.5 18.1 kN.m
M22 0.1 2.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.167
=
Beta = 0.81

Vd(1/2) = 3.6 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C38 (G-5) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 82.4, 89.9 3.7, -3.3 0.0, 0.0
2 56.9, 62.2 2.6, -2.3 0.0, 0.0
3 67.5, 75.0 3.0, -2.8 2.1, -2.0
4 58.1, 65.5 2.9, -2.5 -2.1, 2.0
5 68.3, 74.7 3.1, -2.8 -2.2, 2.0
6 68.3, 74.7 3.1, -2.8 2.2, -2.0
7 67.1, 73.5 1.4, -1.3 0.0, 0.0

ProtaStructure v3.0.4 Page 38

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 69.4, 75.8 4.9, -4.3 0.0, 0.0

Critical Loading: 1 - (G*F)

min Design
N 89.9 - 89.9 kN
M11 3.7 1.0 4.7 kN.m
M22 0.0 -1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 0.0 / 2.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.78 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C39 (G-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 230.1, 237.5 1.5, 0.0 -0.1, 0.0
2 161.1, 166.4 1.1, 0.0 -0.1, 0.0
3 201.0, 208.5 1.2, 0.0 -1.1, 0.0
4 169.8, 177.3 1.2, 0.0 0.8, 0.0
5 193.8, 200.2 1.2, 0.0 -15.3, 0.0
6 192.9, 199.3 1.3, 0.0 15.0, 0.0
7 177.6, 184.0 -13.5, 0.0 -0.1, 0.0

8 209.1, 215.5 16.1, 0.0 -0.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 215.5 - 215.5 kN
M11 16.1 2.5 18.1 kN.m
M22 -0.1 -2.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.163
=
Beta = 0.81

Vd(1/2) = 3.6 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C39 (G-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 80.9, 88.4 3.8, -3.4 -0.3, 0.4
2 55.9, 61.2 2.6, -2.3 -0.2, 0.3
3 66.2, 73.7 3.0, -2.8 -2.4, 2.4
4 57.2, 64.7 3.0, -2.6 1.9, -1.8
5 67.0, 73.4 3.2, -2.8 -2.4, 2.3
6 67.1, 73.5 3.2, -2.8 1.9, -1.7
7 65.9, 72.3 1.4, -1.3 -0.3, 0.3

ProtaStructure v3.0.4 Page 39

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 68.2, 74.6 4.9, -4.3 -0.2, 0.3

Critical Loading: 1 - (G*F)

min Design
N 88.4 - 88.4 kN
M11 3.8 1.0 4.7 kN.m
M22 0.4 1.0 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.067
=
Beta = 0.92

Vd(1/2) = 0.9 / 2.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C40 (G-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 266.0, 273.4 1.4, 0.0 1.2, 0.0
2 186.3, 191.6 1.0, 0.0 0.9, 0.0
3 231.9, 239.3 1.1, 0.0 2.1, 0.0
4 196.6, 204.0 1.2, 0.0 -0.1, 0.0
5 221.4, 227.8 1.2, 0.0 -14.3, 0.0
6 225.6, 232.0 1.2, 0.0 16.3, 0.0
7 208.2, 214.6 -13.6, 0.0 1.1, 0.0

8 238.9, 245.3 16.0, 0.0 1.0, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 232.0 - 232.0 kN
M11 1.2 2.7 0.0 kN.m
M22 16.3 2.7 18.4 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.175
=
Beta = 0.80

Vd(1/2) = 3.9 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.89 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.06 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C40 (G-7) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 90.9, 98.4 3.5, -3.1 1.9, -2.1
2 62.7, 68.1 2.5, -2.2 1.3, -1.5
3 74.4, 81.8 2.6, -2.5 3.8, -3.9
4 63.9, 71.4 3.0, -2.5 -0.8, 0.5
5 75.2, 81.6 3.0, -2.7 -0.7, 0.4
6 75.3, 81.7 2.9, -2.6 3.9, -3.9
7 74.3, 80.7 1.2, -1.2 1.6, -1.8

ProtaStructure v3.0.4 Page 40

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 76.3, 82.7 4.7, -4.1 1.6, -1.7

Critical Loading: 1 - (G*F)

min Design
N 98.4 - 98.4 kN
M11 3.5 1.1 5.4 kN.m
M22 -2.1 -1.1 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.074
=
Beta = 0.91

Vd(1/2) = 1.9 / 2.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.85 / 0.85 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C41 (G-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 210.0, 217.5 1.2, 0.0 -4.1, 0.0
2 147.0, 152.3 0.8, 0.0 -2.9, 0.0
3 188.0, 195.4 0.9, 0.0 -4.3, 0.0
4 149.9, 157.4 0.9, 0.0 -2.4, 0.0
5 177.7, 184.1 1.0, 0.0 -18.0, 0.0
6 175.0, 181.4 1.0, 0.0 11.1, 0.0
7 173.9, 180.3 -14.5, 0.0 -3.4, 0.0

8 178.8, 185.2 16.4, 0.0 -3.5, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 184.1 - 184.1 kN
M11 1.0 2.1 0.0 kN.m
M22 -18.0 -2.1 -19.7 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.139
=
Beta = 0.84

Vd(1/2) = 4.3 / 3.9 kN Short Column... As (Req): %0.41 217.08 mm2

vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.08 N/mm2 Le2/b2 = 12.3 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C41 (G-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 64.5, 72.0 1.7, -1.9 -7.3, 7.8
2 44.6, 49.9 1.2, -1.4 -5.1, 5.5
3 57.4, 64.8 1.5, -1.5 -7.9, 8.4
4 41.5, 48.9 1.3, -1.6 -3.5, 4.1
5 52.9, 59.3 1.5, -1.6 -7.8, 7.6
6 54.1, 60.5 1.4, -1.6 -4.5, 5.5
7 53.7, 60.0 -0.9, 0.7 -6.0, 6.5

ProtaStructure v3.0.4 Page 41

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 53.4, 59.8 3.8, -3.9 -6.2, 6.6

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 59.8 - 59.8 kN
M11 -3.9 -0.7 0.0 kN.m
M22 6.6 0.7 10.3 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.045
=
Beta = 0.95

Vd(1/2) = 3.7 / 1.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.83 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.04 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C42 (F-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 190.7, 198.1 -1.1, 0.0 1.8, 0.0
2 133.5, 138.9 -0.8, 0.0 1.3, 0.0
3 188.0, 195.5 -1.3, 0.0 1.4, 0.0
4 119.7, 127.2 -0.5, 0.0 1.5, 0.0
5 147.4, 153.8 -0.8, 0.0 -13.3, 0.0
6 173.1, 179.5 -1.0, 0.0 16.4, 0.0
7 156.4, 162.8 -16.2, 0.0 1.5, 0.0

8 164.1, 170.5 14.3, 0.0 1.5, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 162.8 - 162.8 kN
M11 -16.2 -1.9 -17.8 kN.m
M22 1.5 1.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.123
=
Beta = 0.85

Vd(1/2) = 3.9 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.85 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C42 (F-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 69.3, 76.8 -2.1, 2.2 4.4, -3.9
2 47.8, 53.2 -1.5, 1.6 3.1, -2.7
3 63.3, 70.8 -2.8, 2.8 3.1, -2.8
4 42.2, 49.7 -0.6, 0.8 3.9, -3.4
5 57.0, 63.4 -1.6, 1.7 1.9, -1.8
6 57.8, 64.2 -1.9, 2.0 5.4, -4.8
7 56.8, 63.2 -4.0, 3.9 3.7, -3.3

ProtaStructure v3.0.4 Page 42

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 58.0, 64.4 0.4, -0.1 3.6, -3.2

Critical Loading: 1 - (G*F)

min Design
N 76.8 - 76.8 kN
M11 2.2 0.9 0.0 kN.m
M22 4.4 0.9 6.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.058
=
Beta = 0.93

Vd(1/2) = 2.4 / 1.9 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.83 N/mm2 Le1/b1 = 11.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C43 (F-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 479.0, 486.5 0.0, 0.0 3.5, 0.0
2 335.6, 341.0 0.0, 0.0 2.4, 0.0
3 360.3, 367.8 -1.5, 0.0 1.9, 0.0
4 410.6, 418.1 1.5, 0.0 3.7, 0.0
5 413.8, 420.2 0.1, 0.0 -12.3, 0.0
6 391.7, 398.0 0.0, 0.0 18.2, 0.0
7 402.4, 408.8 -15.2, 0.0 2.9, 0.0

8 403.1, 409.5 15.2, 0.0 2.9, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 398.0 - 398.0 kN
M11 0.0 -4.6 0.0 kN.m
M22 18.2 4.6 21.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.301
=
Beta = 0.65

Vd(1/2) = 4.3 / 3.6 kN Short Column... As (Req): %0.57 302.89 mm2

vc'(1/2) = 0.96 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C43 (F-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 114.0, 121.5 -0.2, 0.2 5.4, -6.1
2 78.6, 83.9 -0.2, 0.1 3.8, -4.3
3 81.8, 89.2 -2.5, 2.9 2.8, -3.2
4 90.6, 98.1 2.1, -2.5 5.9, -6.5
5 94.6, 101.0 -0.2, 0.2 2.3, -3.0
6 94.0, 100.4 -0.2, 0.2 6.8, -7.2
7 94.2, 100.6 -2.4, 2.2 4.6, -5.1

ProtaStructure v3.0.4 Page 43

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 94.4, 100.8 2.0, -1.8 4.5, -5.1

Critical Loading: 1 - (G*F)

min Design
N 121.5 - 121.5 kN
M11 -0.2 -1.4 0.0 kN.m
M22 -6.1 -1.4 -7.3 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.092
=
Beta = 0.89

Vd(1/2) = 3.3 / 1.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.03 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C44 (F-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 599.9, 607.3 0.1, 0.0 -0.6, 0.0
2 420.2, 425.6 0.1, 0.0 -0.4, 0.0
3 481.2, 488.7 1.9, 0.0 1.1, 0.0
4 483.2, 490.6 -1.7, 0.0 -2.1, 0.0
5 501.5, 507.9 0.2, 0.0 -15.7, 0.0
6 507.0, 513.4 0.0, 0.0 14.8, 0.0
7 504.3, 510.7 -15.2, 0.0 -0.5, 0.0

8 504.3, 510.7 15.3, 0.0 -0.5, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 507.9 - 507.9 kN
M11 0.2 5.8 0.0 kN.m
M22 -15.7 -5.8 -19.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.384
=
Beta = 0.55

Vd(1/2) = 3.7 / 3.6 kN Short Column... As (Req): %0.77 408.45 mm2

vc'(1/2) = 1.02 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C44 (F-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 144.1, 151.6 0.0, 0.0 -0.6, 0.9
2 99.4, 104.7 0.0, 0.0 -0.4, 0.7
3 109.6, 117.1 -0.7, -1.4 2.1, -2.1
4 109.1, 116.5 0.7, 1.4 -3.1, 3.7
5 119.5, 125.9 0.0, 0.0 -2.9, 3.0
6 119.1, 125.5 0.0, 0.0 1.8, -1.4
7 119.3, 125.7 -2.4, 2.2 -0.5, 0.8

ProtaStructure v3.0.4 Page 44

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 119.2, 125.6 2.4, -2.3 -0.5, 0.8

Critical Loading: 1 - (G*F)

min Design
N 151.6 - 151.6 kN
M11 0.0 -1.7 -3.2 kN.m
M22 0.9 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.115
=
Beta = 0.86

Vd(1/2) = 1.6 / 0.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.81 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C45 (F-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 323.8, 331.2 0.1, 0.0 -4.9, 0.0
2 226.9, 232.2 0.0, 0.0 -3.4, 0.0
3 285.2, 292.6 -1.1, 0.0 -5.2, 0.0
4 237.2, 244.7 1.2, 0.0 -2.7, 0.0
5 279.6, 286.0 0.2, 0.0 -18.7, 0.0
6 265.0, 271.4 -0.1, 0.0 10.4, 0.0
7 272.2, 278.6 -15.2, 0.0 -4.1, 0.0

8 272.4, 278.8 15.3, 0.0 -4.1, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 286.0 - 286.0 kN
M11 0.2 3.3 0.0 kN.m
M22 -18.7 -3.3 -21.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.216
=
Beta = 0.75

Vd(1/2) = 4.4 / 3.6 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C45 (F-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.4, 105.8 0.0, -0.1 -7.9, 8.9
2 67.9, 73.2 0.0, 0.0 -5.5, 6.2
3 82.2, 89.6 -2.5, 2.4 -8.0, 9.2
4 67.3, 74.8 2.5, -2.5 -4.3, 4.9
5 82.1, 88.5 0.0, -0.1 -8.2, 8.6
6 80.8, 87.2 0.0, 0.0 -5.0, 6.3
7 81.5, 87.9 -2.3, 2.0 -6.6, 7.5

ProtaStructure v3.0.4 Page 45

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 81.4, 87.8 2.3, -2.1 -6.6, 7.5

Critical Loading: 3 - (G+Q *F1)

min Design
N 89.6 - 89.6 kN
M11 -2.5 -1.0 0.0 kN.m
M22 9.2 1.0 11.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 4.1 / 1.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.02 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C46 (E-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 240.6, 248.1 0.2, 0.0 1.5, 0.0
2 168.5, 173.9 0.1, 0.0 1.0, 0.0
3 207.3, 214.7 1.1, 0.0 1.2, 0.0
4 180.5, 188.0 -0.7, 0.0 1.2, 0.0
5 186.2, 192.6 0.2, 0.0 -13.5, 0.0
6 218.3, 224.7 0.2, 0.0 16.0, 0.0
7 202.4, 208.8 -15.0, 0.0 1.2, 0.0

8 202.1, 208.5 15.4, 0.0 1.3, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 224.7 - 224.7 kN
M11 0.2 2.6 0.0 kN.m
M22 16.0 2.6 18.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.170
=
Beta = 0.80

Vd(1/2) = 3.2 / 3.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.87 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C46 (E-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 83.5, 91.0 0.1, -0.2 3.6, -3.2
2 57.6, 63.0 0.1, -0.1 2.5, -2.3
3 67.4, 74.9 2.0, -1.9 2.9, -2.7
4 59.8, 67.3 -1.9, 1.7 2.9, -2.4
5 67.9, 74.3 0.1, -0.1 1.3, -1.2
6 70.4, 76.8 0.1, -0.2 4.8, -4.2
7 69.2, 75.6 -2.1, 1.8 3.0, -2.7

ProtaStructure v3.0.4 Page 46

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 69.2, 75.6 2.2, -2.0 3.1, -2.7

Critical Loading: 1 - (G*F)

min Design
N 91.0 - 91.0 kN
M11 -0.2 -1.0 0.0 kN.m
M22 3.6 1.0 4.6 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.069
=
Beta = 0.92

Vd(1/2) = 2.1 / 0.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.83 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C47 (E-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 484.5, 492.0 0.1, 0.0 3.2, 0.0
2 339.4, 344.8 0.0, 0.0 2.3, 0.0
3 360.3, 367.8 1.7, 0.0 1.8, 0.0
4 419.3, 426.8 -1.6, 0.0 3.5, 0.0
5 418.3, 424.7 0.1, 0.0 -12.4, 0.0
6 396.4, 402.8 0.0, 0.0 17.9, 0.0
7 407.4, 413.8 -15.1, 0.0 2.7, 0.0

8 407.3, 413.7 15.2, 0.0 2.8, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 402.8 - 402.8 kN
M11 0.0 -4.6 0.0 kN.m
M22 17.9 4.6 20.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.305
=
Beta = 0.64

Vd(1/2) = 4.3 / 3.6 kN Short Column... As (Req): %0.57 299.77 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C47 (E-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.7, 124.2 -0.1, 0.1 5.0, -5.7
2 80.4, 85.8 -0.1, 0.1 3.5, -4.0
3 82.3, 89.7 2.3, -2.7 2.7, -3.2
4 94.5, 101.9 -2.5, 2.8 5.2, -5.9
5 96.8, 103.2 -0.1, 0.1 1.9, -2.6
6 96.3, 102.7 -0.1, 0.1 6.4, -6.9
7 96.5, 102.9 -2.3, 2.0 4.2, -4.8

ProtaStructure v3.0.4 Page 47

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 96.5, 102.9 2.1, -1.9 4.2, -4.8

Critical Loading: 1 - (G*F)

min Design
N 124.2 - 124.2 kN
M11 -0.1 -1.4 0.0 kN.m
M22 -5.7 -1.4 -6.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 3.2 / 1.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.02 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C48 (E-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 598.7, 606.2 0.0, 0.0 -0.5, 0.0
2 419.4, 424.8 0.0, 0.0 -0.4, 0.0
3 480.8, 488.2 -1.7, 0.0 1.1, 0.0
4 481.8, 489.3 1.8, 0.0 -2.0, 0.0
5 500.7, 507.1 0.1, 0.0 -15.7, 0.0
6 505.9, 512.3 -0.1, 0.0 14.8, 0.0
7 503.4, 509.8 -15.2, 0.0 -0.5, 0.0

8 503.2, 509.6 15.2, 0.0 -0.4, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 507.1 - 507.1 kN
M11 0.1 5.8 0.0 kN.m
M22 -15.7 -5.8 -18.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.383
=
Beta = 0.55

Vd(1/2) = 3.7 / 3.6 kN Short Column... As (Req): %0.76 403.74 mm2

vc'(1/2) = 1.01 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C48 (E-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 143.4, 150.9 0.1, 0.0 -0.5, 0.8
2 98.9, 104.2 0.0, 0.0 -0.4, 0.6
3 109.3, 116.8 0.6, 1.6 2.3, -2.3
4 108.3, 115.8 -0.5, -1.5 -3.2, 3.7
5 118.9, 125.3 0.1, 0.0 -2.9, 3.0
6 118.5, 124.9 0.0, 0.0 2.0, -1.6
7 118.7, 125.1 -2.4, 2.2 -0.4, 0.7

ProtaStructure v3.0.4 Page 48

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 118.7, 125.1 2.5, -2.2 -0.4, 0.7

Critical Loading: 1 - (G*F)

min Design
N 150.9 - 150.9 kN
M11 0.1 1.7 3.2 kN.m
M22 0.8 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.114
=
Beta = 0.86

Vd(1/2) = 1.6 / 0.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.81 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C49 (E-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 323.5, 331.0 0.0, 0.0 -4.9, 0.0
2 226.7, 232.1 0.0, 0.0 -3.4, 0.0
3 287.8, 295.3 1.1, 0.0 -5.2, 0.0
4 234.1, 241.6 -1.0, 0.0 -2.7, 0.0
5 279.4, 285.8 0.2, 0.0 -18.6, 0.0
6 264.8, 271.2 -0.1, 0.0 10.4, 0.0
7 272.1, 278.5 -15.2, 0.0 -4.2, 0.0

8 272.1, 278.5 15.3, 0.0 -4.1, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 285.8 - 285.8 kN
M11 0.2 3.3 0.0 kN.m
M22 -18.6 -3.3 -21.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.216
=
Beta = 0.75

Vd(1/2) = 4.4 / 3.6 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C49 (E-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.3, 105.8 0.0, 0.0 -7.9, 8.9
2 67.8, 73.2 0.0, 0.0 -5.5, 6.2
3 83.3, 90.7 2.2, -2.1 -7.9, 9.1
4 66.2, 73.7 -2.1, 2.1 -4.4, 5.0
5 82.1, 88.5 0.0, 0.0 -8.3, 8.6
6 80.8, 87.2 0.0, 0.0 -4.9, 6.3
7 81.4, 87.8 -2.3, 2.1 -6.6, 7.4

ProtaStructure v3.0.4 Page 49

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 81.4, 87.8 2.3, -2.1 -6.6, 7.4

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.7 - 90.7 kN
M11 2.2 1.0 0.0 kN.m
M22 9.1 1.0 11.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.069
=
Beta = 0.92

Vd(1/2) = 4.0 / 1.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.84 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.02 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C50 (D-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 236.2, 243.6 0.0, 0.0 1.5, 0.0
2 165.4, 170.7 0.0, 0.0 1.1, 0.0
3 206.7, 214.2 -0.9, 0.0 1.2, 0.0
4 174.0, 181.4 0.9, 0.0 1.2, 0.0
5 182.9, 189.3 0.0, 0.0 -13.5, 0.0
6 214.0, 220.4 0.0, 0.0 16.0, 0.0
7 198.5, 204.9 -15.2, 0.0 1.2, 0.0

8 198.5, 204.9 15.2, 0.0 1.4, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 220.4 - 220.4 kN
M11 0.0 -2.5 0.0 kN.m
M22 16.0 2.5 18.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.167
=
Beta = 0.81

Vd(1/2) = 3.8 / 3.6 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.87 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C50 (D-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 82.4, 89.8 -0.2, 0.2 3.7, -3.3
2 56.9, 62.2 -0.1, 0.1 2.6, -2.3
3 67.5, 75.0 -2.3, 2.2 3.0, -2.7
4 58.0, 65.5 2.0, -1.9 3.0, -2.5
5 67.1, 73.5 -0.1, 0.2 1.4, -1.3
6 69.4, 75.8 -0.1, 0.2 4.9, -4.3
7 68.2, 74.6 -2.3, 2.1 3.1, -2.8

ProtaStructure v3.0.4 Page 50

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 68.3, 74.7 2.0, -1.8 3.1, -2.8

Critical Loading: 1 - (G*F)

min Design
N 89.8 - 89.8 kN
M11 0.2 1.0 0.0 kN.m
M22 3.7 1.0 4.7 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 2.2 / 0.9 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.83 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C51 (D-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 485.1, 492.5 0.0, 0.0 3.3, 0.0
2 339.9, 345.2 0.0, 0.0 2.3, 0.0
3 361.2, 368.7 -1.6, 0.0 1.8, 0.0
4 419.5, 426.9 1.6, 0.0 3.5, 0.0
5 418.8, 425.2 0.1, 0.0 -12.4, 0.0
6 396.9, 403.3 -0.1, 0.0 17.9, 0.0
7 407.9, 414.3 -15.2, 0.0 2.7, 0.0

8 407.7, 414.1 15.2, 0.0 2.8, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 403.3 - 403.3 kN
M11 -0.1 -4.6 0.0 kN.m
M22 17.9 4.6 20.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.305
=
Beta = 0.64

Vd(1/2) = 4.3 / 3.6 kN Short Column... As (Req): %0.57 299.89 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C51 (D-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.3, 123.7 -0.1, 0.2 5.0, -5.7
2 80.1, 85.5 -0.1, 0.1 3.5, -4.0
3 82.0, 89.5 -2.6, 3.0 2.8, -3.2
4 93.9, 101.4 2.4, -2.7 5.2, -5.9
5 96.4, 102.8 -0.1, 0.1 2.0, -2.6
6 95.9, 102.3 -0.1, 0.1 6.5, -6.9
7 96.1, 102.5 -2.3, 2.1 4.2, -4.8

ProtaStructure v3.0.4 Page 51

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 96.2, 102.6 2.1, -1.8 4.2, -4.8

Critical Loading: 1 - (G*F)

min Design
N 123.7 - 123.7 kN
M11 0.2 1.4 0.0 kN.m
M22 -5.7 -1.4 -7.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.094
=
Beta = 0.89

Vd(1/2) = 3.2 / 1.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.03 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C52 (D-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 596.3, 603.8 0.2, 0.0 -0.5, 0.0
2 417.7, 423.1 0.2, 0.0 -0.4, 0.0
3 478.6, 486.1 2.0, 0.0 1.1, 0.0
4 480.2, 487.7 -1.6, 0.0 -2.0, 0.0
5 498.6, 505.0 0.3, 0.0 -15.6, 0.0
6 503.9, 510.3 0.1, 0.0 14.7, 0.0
7 500.8, 507.2 -15.0, 0.0 -0.5, 0.0

8 501.7, 508.1 15.4, 0.0 -0.4, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 505.0 - 505.0 kN
M11 0.3 5.8 0.0 kN.m
M22 -15.6 -5.8 -18.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.382
=
Beta = 0.55

Vd(1/2) = 3.7 / 3.7 kN Short Column... As (Req): %0.75 397.91 mm2

vc'(1/2) = 1.01 / 1.02 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C52 (D-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 145.4, 152.9 -0.1, -0.1 -0.5, 0.8
2 100.3, 105.6 -0.1, -0.1 -0.4, 0.6
3 110.6, 118.1 -0.7, -1.5 2.3, -2.3
4 110.1, 117.6 0.6, 1.3 -3.2, 3.8
5 120.6, 127.0 -0.1, -0.1 -2.9, 3.0
6 120.2, 126.6 -0.1, -0.1 2.0, -1.6
7 120.4, 126.8 -2.5, 2.1 -0.4, 0.7

ProtaStructure v3.0.4 Page 52

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 120.3, 126.7 2.3, -2.3 -0.4, 0.7

Critical Loading: 1 - (G*F)

min Design
N 152.9 - 152.9 kN
M11 -0.1 -1.8 -3.3 kN.m
M22 0.8 1.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.116
=
Beta = 0.86

Vd(1/2) = 1.7 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.78 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C53 (D-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 323.4, 330.8 0.1, 0.0 -4.9, 0.0
2 226.6, 232.0 0.1, 0.0 -3.4, 0.0
3 286.6, 294.1 -0.9, 0.0 -5.2, 0.0
4 235.2, 242.7 1.1, 0.0 -2.6, 0.0
5 279.3, 285.7 0.2, 0.0 -18.6, 0.0
6 264.7, 271.1 -0.1, 0.0 10.4, 0.0
7 272.1, 278.5 -15.2, 0.0 -4.2, 0.0

8 271.9, 278.3 15.3, 0.0 -4.0, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 285.7 - 285.7 kN
M11 0.2 3.3 0.0 kN.m
M22 -18.6 -3.3 -21.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.216
=
Beta = 0.75

Vd(1/2) = 4.4 / 3.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C53 (D-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 98.8, 106.2 0.0, 0.0 -7.9, 8.9
2 68.2, 73.5 0.0, 0.0 -5.5, 6.2
3 83.2, 90.7 -2.2, 2.2 -7.9, 9.0
4 66.9, 74.4 2.2, -2.2 -4.5, 5.0
5 82.5, 88.9 0.0, 0.0 -8.3, 8.6
6 81.1, 87.5 0.0, 0.0 -4.9, 6.3
7 81.8, 88.2 -2.3, 2.1 -6.6, 7.4

ProtaStructure v3.0.4 Page 53

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 81.8, 88.2 2.3, -2.1 -6.6, 7.4

Critical Loading: 3 - (G+Q *F1)

min Design
N 90.7 - 90.7 kN
M11 -2.2 -1.0 0.0 kN.m
M22 9.0 1.0 11.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.069
=
Beta = 0.92

Vd(1/2) = 4.0 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.79 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.00 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C54 (C-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 229.3, 236.8 0.3, 0.0 1.5, 0.0
2 160.6, 165.9 0.2, 0.0 1.1, 0.0
3 201.6, 209.1 1.2, 0.0 1.2, 0.0
4 168.1, 175.6 -0.8, 0.0 1.2, 0.0
5 177.2, 183.6 0.3, 0.0 -13.4, 0.0
6 208.3, 214.7 0.2, 0.0 16.0, 0.0
7 192.3, 198.7 -14.9, 0.0 1.2, 0.0

8 193.2, 199.6 15.4, 0.0 1.4, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 214.7 - 214.7 kN
M11 0.2 2.5 0.0 kN.m
M22 16.0 2.5 18.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.162
=
Beta = 0.81

Vd(1/2) = 3.8 / 3.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.87 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C54 (C-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 80.5, 88.0 0.2, -0.2 3.7, -3.2
2 55.6, 60.9 0.1, -0.2 2.5, -2.3
3 66.2, 73.7 2.2, -2.1 2.9, -2.7
4 56.6, 64.0 -1.9, 1.7 2.9, -2.4
5 65.6, 72.0 0.1, -0.2 1.3, -1.2
6 67.9, 74.3 0.2, -0.2 4.8, -4.2
7 66.8, 73.2 -2.0, 1.7 3.1, -2.7

ProtaStructure v3.0.4 Page 54

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 66.7, 73.1 2.3, -2.1 3.1, -2.7

Critical Loading: 1 - (G*F)

min Design
N 88.0 - 88.0 kN
M11 -0.2 -1.0 0.0 kN.m
M22 3.7 1.0 4.6 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.067
=
Beta = 0.92

Vd(1/2) = 2.1 / 0.9 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.83 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C55 (C-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 477.2, 484.7 0.4, 0.0 3.3, 0.0
2 334.1, 339.4 0.3, 0.0 2.3, 0.0
3 354.1, 361.6 1.9, 0.0 1.8, 0.0
4 411.6, 419.1 -1.3, 0.0 3.5, 0.0
5 411.8, 418.2 0.4, 0.0 -12.3, 0.0
6 390.0, 396.4 0.3, 0.0 17.9, 0.0
7 400.8, 407.2 -14.9, 0.0 2.7, 0.0

8 401.0, 407.4 15.5, 0.0 2.9, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 396.4 - 396.4 kN
M11 0.3 4.6 0.0 kN.m
M22 17.9 4.6 20.9 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.300
=
Beta = 0.65

Vd(1/2) = 4.3 / 3.7 kN Short Column... As (Req): %0.54 287.31 mm2

vc'(1/2) = 0.96 / 0.97 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C55 (C-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 116.2, 123.6 0.1, -0.3 5.0, -5.7
2 80.1, 85.4 0.1, -0.2 3.5, -4.0
3 82.6, 90.1 2.4, -2.9 2.8, -3.2
4 93.4, 100.9 -2.2, 2.4 5.2, -5.9
5 96.4, 102.8 0.1, -0.3 2.0, -2.7
6 95.8, 102.2 0.1, -0.3 6.5, -6.9
7 96.2, 102.6 -2.1, 1.7 4.2, -4.8

ProtaStructure v3.0.4 Page 55

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 96.0, 102.4 2.3, -2.2 4.2, -4.8

Critical Loading: 1 - (G*F)

min Design
N 123.6 - 123.6 kN
M11 -0.3 -1.4 0.0 kN.m
M22 -5.7 -1.4 -7.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.093
=
Beta = 0.89

Vd(1/2) = 3.2 / 1.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.86 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.03 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C56 (C-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 620.9, 628.4 -0.9, 0.0 -0.3, 0.0
2 434.5, 439.9 -0.6, 0.0 -0.2, 0.0
3 498.8, 506.2 -2.4, 0.0 1.3, 0.0
4 495.9, 503.4 1.1, 0.0 -1.9, 0.0
5 518.8, 525.2 -0.6, 0.0 -15.4, 0.0
6 524.1, 530.5 -0.8, 0.0 14.9, 0.0
7 524.2, 530.6 -16.1, 0.0 -0.4, 0.0

8 518.7, 525.1 14.6, 0.0 -0.2, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 530.6 - 530.6 kN
M11 -16.1 -6.1 -19.3 kN.m
M22 -0.4 -6.1 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.401
=
Beta = 0.53

Vd(1/2) = 3.7 / 3.8 kN Short Column... As (Req): %0.90 474.83 mm2

vc'(1/2) = 1.02 / 1.03 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C56 (C-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 138.9, 146.4 0.0, 0.9 -0.4, 0.6
2 95.8, 101.1 0.0, 0.7 -0.3, 0.4
3 106.4, 113.9 0.4, 2.4 2.4, -2.6
4 104.1, 111.6 -0.4, -0.9 -3.2, 3.7
5 115.2, 121.6 0.0, 0.8 -2.8, 2.8
6 114.7, 121.1 0.0, 0.8 2.1, -1.7
7 114.9, 121.3 -2.5, 3.2 -0.4, 0.5

ProtaStructure v3.0.4 Page 56

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 115.0, 121.4 2.5, -1.6 -0.3, 0.5

Critical Loading: 1 - (G*F)

min Design
N 146.4 - 146.4 kN
M11 0.9 1.7 3.1 kN.m
M22 0.6 1.7 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.111
=
Beta = 0.87

Vd(1/2) = 1.6 / 0.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.81 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.00 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C57 (C-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 329.1, 336.6 -0.1, 0.0 -5.2, 0.0
2 230.4, 235.8 -0.1, 0.0 -3.7, 0.0
3 292.7, 300.1 1.0, 0.0 -5.5, 0.0
4 236.7, 244.1 -1.0, 0.0 -2.8, 0.0
5 283.8, 290.2 0.1, 0.0 -18.8, 0.0
6 269.3, 275.7 -0.2, 0.0 10.1, 0.0
7 276.3, 282.7 -15.3, 0.0 -4.5, 0.0

8 276.7, 283.1 15.2, 0.0 -4.3, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 290.2 - 290.2 kN
M11 0.1 3.3 0.0 kN.m
M22 -18.8 -3.3 -21.3 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.219
=
Beta = 0.75

Vd(1/2) = 4.5 / 3.6 kN Short Column... As (Req): %0.42 222.48 mm2

vc'(1/2) = 0.91 / 0.91 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.07 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C57 (C-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 96.9, 104.3 0.1, 0.1 -8.2, 9.4
2 66.9, 72.2 0.1, 0.1 -5.7, 6.5
3 82.1, 89.6 2.1, -1.9 -8.2, 9.5
4 65.3, 72.8 -2.0, 2.0 -4.7, 5.3
5 80.9, 87.3 0.1, 0.1 -8.5, 9.0
6 79.6, 86.0 0.1, 0.1 -5.2, 6.7
7 80.3, 86.7 -2.2, 2.1 -6.9, 7.9

ProtaStructure v3.0.4 Page 57

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 80.2, 86.6 2.4, -2.0 -6.8, 7.8

Critical Loading: 3 - (G+Q *F1)

min Design
N 89.6 - 89.6 kN
M11 2.1 1.0 0.0 kN.m
M22 9.5 1.0 11.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.068
=
Beta = 0.92

Vd(1/2) = 4.2 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.78 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.00 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C58 (B-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 246.9, 254.4 -0.6, 0.0 1.5, 0.0
2 173.1, 178.4 -0.4, 0.0 1.1, 0.0
3 211.5, 219.0 -1.4, 0.0 1.2, 0.0
4 187.7, 195.1 0.4, 0.0 1.2, 0.0
5 192.3, 198.7 -0.5, 0.0 -13.4, 0.0
6 223.2, 229.6 -0.6, 0.0 16.0, 0.0
7 210.4, 216.8 -15.8, 0.0 1.1, 0.0

8 205.0, 211.4 14.8, 0.0 1.4, 0.0

Critical Loading: 7 - ((G+Q)P1 *F2)

min Design
N 216.8 - 216.8 kN
M11 -15.8 -2.5 -17.8 kN.m
M22 1.1 2.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.164
=
Beta = 0.81

Vd(1/2) = 3.8 / 3.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.88 / 0.88 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.07 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C58 (B-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 88.5, 95.9 -1.1, 1.3 3.9, -3.3
2 61.1, 66.4 -0.8, 0.9 2.7, -2.3
3 72.7, 80.2 -3.0, 3.1 3.2, -2.8
4 61.8, 69.3 1.3, -1.0 2.9, -2.4
5 72.2, 78.6 -1.0, 1.1 1.6, -1.3
6 74.4, 80.8 -0.9, 1.1 4.9, -4.2
7 73.4, 79.8 -3.2, 3.2 3.2, -2.7

ProtaStructure v3.0.4 Page 58

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 73.1, 79.5 1.3, -1.0 3.3, -2.8

Critical Loading: 1 - (G*F)

min Design
N 95.9 - 95.9 kN
M11 1.3 1.1 0.0 kN.m
M22 3.9 1.1 5.1 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.073
=
Beta = 0.91

Vd(1/2) = 2.2 / 1.5 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.84 / 0.85 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.04 / 0.03 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C59 (B-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 520.8, 528.2 -1.0, 0.0 3.9, 0.0
2 363.7, 369.1 -0.7, 0.0 2.7, 0.0
3 404.7, 412.2 -2.4, 0.0 2.8, 0.0
4 424.3, 431.8 0.8, 0.0 3.4, 0.0
5 447.2, 453.6 -0.8, 0.0 -11.8, 0.0
6 425.7, 432.1 -0.9, 0.0 18.4, 0.0
7 438.7, 445.1 -16.2, 0.0 3.1, 0.0

8 434.3, 440.7 14.5, 0.0 3.5, 0.0

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 432.1 - 432.1 kN
M11 -0.9 -5.0 0.0 kN.m
M22 18.4 5.0 21.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.327
=
Beta = 0.62

Vd(1/2) = 4.4 / 3.9 kN Short Column... As (Req): %0.71 374.83 mm2

vc'(1/2) = 0.98 / 0.99 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C59 (B-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 114.7, 122.2 -1.2, 1.7 5.0, -6.3
2 79.1, 84.4 -0.8, 1.2 3.5, -4.4
3 80.3, 87.8 -3.6, 4.4 3.2, -4.4
4 93.2, 100.7 1.7, -1.6 4.7, -5.5
5 95.1, 101.5 -1.0, 1.5 2.0, -3.2
6 94.6, 101.0 -1.0, 1.5 6.4, -7.3
7 94.8, 101.2 -3.3, 3.6 4.1, -5.2

ProtaStructure v3.0.4 Page 59

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 95.0, 101.4 1.3, -0.7 4.3, -5.3

Critical Loading: 1 - (G*F)

min Design
N 122.2 - 122.2 kN
M11 1.7 1.4 0.0 kN.m
M22 -6.3 -1.4 -7.8 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.092
=
Beta = 0.89

Vd(1/2) = 3.3 / 1.9 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.85 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.04 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C60 (B-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 485.5, 492.9 5.5, 0.0 -2.3, 0.0
2 339.1, 344.4 3.9, 0.0 -1.6, 0.0
3 417.4, 424.9 6.0, 0.0 -1.0, 0.0
4 355.3, 362.8 2.9, 0.0 -2.4, 0.0
5 404.5, 410.9 4.7, 0.0 -17.0, 0.0
6 409.2, 415.6 4.6, 0.0 13.2, 0.0
7 399.5, 405.9 -10.0, 0.0 -2.0, 0.0

8 414.3, 420.7 19.3, 0.0 -1.7, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 420.7 - 420.7 kN
M11 19.3 4.8 22.3 kN.m
M22 -1.7 -4.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.318
=
Beta = 0.63

Vd(1/2) = 4.0 / 4.6 kN Short Column... As (Req): %0.75 396.62 mm2

vc'(1/2) = 0.97 / 0.97 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C60 (B-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 153.7, 161.2 3.0, -7.0 -1.8, 3.3
2 106.1, 111.4 2.1, -4.9 -1.3, 2.3
3 116.7, 124.2 1.7, -6.7 0.7, 0.7
4 116.9, 124.3 3.3, -4.5 -3.6, 4.4
5 127.5, 133.9 2.6, -5.9 -3.9, 4.9
6 127.1, 133.5 2.6, -5.9 0.8, 0.6
7 126.5, 132.9 0.6, -4.5 -1.5, 2.8

ProtaStructure v3.0.4 Page 60

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 128.1, 134.5 4.5, -7.3 -1.5, 2.7

Critical Loading: 1 - (G*F)

min Design
N 161.2 - 161.2 kN
M11 -7.0 -1.9 -9.8 kN.m
M22 3.3 1.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.122
=
Beta = 0.86

Vd(1/2) = 0.0 / 2.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.78 / 0.85 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.04 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C61 (B-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 294.7, 411.4 1.7, 0.0 -2.7, 0.0
2 207.0, 287.6 1.2, 0.0 -1.9, 0.0
3 253.3, 370.0 -0.6, 0.0 -3.1, 0.0
4 226.3, 289.5 2.5, 0.0 -1.4, 0.0
5 255.4, 352.2 1.6, 0.0 -16.0, 0.0
6 241.4, 338.1 1.3, 0.0 11.3, 0.0
7 250.6, 347.3 -13.6, 0.0 -2.4, 0.0

8 246.2, 343.0 16.5, 0.0 -2.2, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 343.0 - 343.0 kN
M11 16.5 3.9 19.2 kN.m
M22 -2.2 -3.9 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.259
=
Beta = 0.70

Vd(1/2) = 4.3 / 2.9 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.92 / 0.87 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.09 / 0.06 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C61 (B-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 101.3, 108.7 -0.4, -0.2 -6.1, 5.9
2 69.8, 75.2 -0.3, -0.1 -4.2, 4.1
3 85.4, 92.9 -2.4, 1.8 -6.4, 6.3
4 68.2, 75.6 1.8, -1.9 -3.1, 3.2
5 84.5, 90.8 -0.3, -0.2 -6.7, 6.2
6 83.1, 89.5 -0.3, -0.1 -3.4, 3.8
7 83.9, 90.3 -2.7, 2.1 -5.0, 4.9

ProtaStructure v3.0.4 Page 61

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 83.7, 90.1 2.1, -2.4 -5.1, 5.0

Critical Loading: 1 - (G*F)

min Design
N 108.7 - 108.7 kN
M11 -0.4 -1.3 0.0 kN.m
M22 -6.1 -1.3 -7.2 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.082
=
Beta = 0.90

Vd(1/2) = 3.1 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.80 N/mm2 Le1/b1 = 11.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.00 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C62 (A-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 112.2, 119.7 3.7, 0.0 1.1, 0.0
2 78.8, 84.2 2.6, 0.0 0.8, 0.0
3 121.7, 129.2 3.8, 0.0 0.9, 0.0
4 62.1, 69.5 2.2, 0.0 0.9, 0.0
5 79.4, 85.8 3.1, 0.0 -13.7, 0.0
6 109.8, 116.2 3.1, 0.0 15.6, 0.0
7 86.9, 93.3 -11.5, 0.0 0.8, 0.0

8 102.3, 108.7 17.7, 0.0 1.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 108.7 - 108.7 kN
M11 17.7 1.2 18.8 kN.m
M22 1.1 1.2 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.082
=
Beta = 0.90

Vd(1/2) = 3.3 / 4.2 kN Short Column... As (Req): %0.62 328.61 mm2

vc'(1/2) = 0.82 / 0.83 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.06 / 0.08 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C62 (A-8) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 43.8, 51.2 6.5, -6.8 2.9, -2.4
2 30.3, 35.6 4.5, -4.8 2.0, -1.7
3 47.8, 55.3 6.8, -7.0 2.6, -2.2
4 19.1, 26.5 3.4, -3.9 2.0, -1.7
5 35.3, 41.7 5.4, -5.7 0.8, -0.7
6 37.3, 43.7 5.5, -5.7 4.0, -3.3
7 35.5, 41.9 3.9, -4.7 2.4, -2.0

ProtaStructure v3.0.4 Page 62

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 37.1, 43.5 7.0, -6.8 2.5, -2.1

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 43.7 - 43.7 kN
M11 -5.7 -0.5 -9.6 kN.m
M22 4.0 0.5 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.033
=
Beta = 0.96

Vd(1/2) = 1.8 / 3.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.81 / 0.81 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.03 / 0.07 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C63 (A-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 312.1, 319.5 5.7, 0.0 3.0, 0.0
2 218.2, 223.5 4.0, 0.0 2.1, 0.0
3 273.8, 281.3 6.0, 0.0 2.4, 0.0
4 225.5, 233.0 3.2, 0.0 2.4, 0.0
5 272.5, 278.9 4.9, 0.0 -12.5, 0.0
6 251.2, 257.6 4.8, 0.0 17.6, 0.0
7 255.0, 261.4 -9.8, 0.0 2.4, 0.0

8 268.6, 275.0 19.4, 0.0 2.7, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 275.0 - 275.0 kN
M11 19.4 3.2 21.8 kN.m
M22 2.7 3.2 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.208
=
Beta = 0.76

Vd(1/2) = 4.2 / 4.6 kN Short Column... As (Req): %0.46 243.36 mm2

vc'(1/2) = 0.90 / 0.91 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.09 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C63 (A-9) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 76.6, 84.1 8.0, -9.6 4.0, -4.8
2 52.8, 58.1 5.6, -6.7 2.8, -3.4
3 58.3, 65.8 8.1, -9.9 2.5, -3.6
4 57.7, 65.2 4.3, -5.3 3.8, -4.0
5 63.6, 70.0 6.7, -8.0 1.3, -2.1
6 63.2, 69.6 6.7, -8.0 5.4, -6.0
7 62.8, 69.2 5.0, -6.9 3.3, -4.0

ProtaStructure v3.0.4 Page 63

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 63.9, 70.3 8.3, -9.1 3.4, -4.1

Critical Loading: 6 - ((G+Q)P2 *F)

min Design
N 69.6 - 69.6 kN
M11 -8.0 -0.8 -13.7 kN.m
M22 -6.0 -0.8 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.053
=
Beta = 0.94

Vd(1/2) = 2.7 / 4.3 kN Short Column... As (Req): %0.42 220.27 mm2

vc'(1/2) = 0.84 / 0.84 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.09 N/mm2 Le2/b2 = 11.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C64 (A-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 289.9, 297.4 -0.8, 0.0 -2.0, 0.0
2 203.1, 208.4 -0.6, 0.0 -1.4, 0.0
3 256.1, 263.6 -0.9, 0.0 -1.4, 0.0
4 211.3, 218.8 -0.4, 0.0 -1.6, 0.0
5 241.4, 247.8 -0.6, 0.0 -16.8, 0.0
6 246.1, 252.5 -0.7, 0.0 13.4, 0.0
7 243.6, 250.0 -8.2, 0.0 -1.8, 0.0

8 243.9, 250.3 6.8, 0.0 -1.5, 0.0

Critical Loading: 5 - ((G+Q)P1 *F)

min Design
N 247.8 - 247.8 kN
M11 -0.6 -2.8 0.0 kN.m
M22 -16.8 -2.8 -22.5 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.187
=
Beta = 0.78

Vd(1/2) = 4.0 / 2.0 kN Slender Column... As (Req): %0.51 268.30 mm2

vc'(1/2) = 0.89 / 0.89 N/mm2 Le1/b1 = 14.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.04 N/mm2 Le2/b2 = 15.6 ≥ 15.0
Madd(1/2) = 0.0 / 6.9 kN.m 4H16
Links = H8-175

2C64 (A-10) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 107.9, 115.4 4.3, -1.1 -1.4, 2.9
2 74.4, 79.8 2.9, -0.7 -1.0, 2.0
3 91.8, 99.3 4.5, -1.1 0.6, 1.2
4 72.0, 79.5 2.0, -0.5 -2.8, 3.2
5 89.5, 95.9 3.5, -0.8 -3.4, 4.5
6 89.1, 95.5 3.5, -0.9 1.1, 0.3
7 89.5, 95.9 5.2, -8.2 -1.2, 2.4

ProtaStructure v3.0.4 Page 64

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 89.2, 95.6 1.8, 6.4 -1.1, 2.4

Critical Loading: 1 - (G*F)

min Design
N 115.4 - 115.4 kN
M11 4.3 1.3 6.9 kN.m
M22 2.9 1.3 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.087
=
Beta = 0.90

Vd(1/2) = 0.1 / 3.2 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.80 / 0.85 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.06 N/mm2 Le2/b2 = 11.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C65 (A-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 143.6, 260.4 3.7, 0.0 -1.5, 0.0
2 101.4, 182.0 2.7, 0.0 -1.1, 0.0
3 149.9, 266.7 4.6, 0.0 -1.5, 0.0
4 88.7, 151.9 2.0, 0.0 -1.2, 0.0
5 128.7, 225.4 3.4, 0.0 -14.9, 0.0
6 114.7, 211.4 3.1, 0.0 12.4, 0.0
7 114.8, 211.5 -10.3, 0.0 -1.5, 0.0

8 128.5, 225.2 16.8, 0.0 -1.1, 0.0

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 225.2 - 225.2 kN
M11 16.8 2.6 18.8 kN.m
M22 -1.1 -2.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.170
=
Beta = 0.80

Vd(1/2) = 4.1 / 5.5 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.85 / 0.86 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.08 / 0.11 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C65 (A-11) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 58.1, 65.6 6.1, -5.4 -5.2, 4.2
2 40.1, 45.5 4.2, -3.8 -3.6, 3.0
3 60.5, 68.0 6.3, -5.6 -5.3, 4.2
4 27.9, 35.4 3.3, -3.3 -2.9, 2.8
5 48.8, 55.2 5.1, -4.6 -5.9, 4.7
6 47.5, 53.9 5.1, -4.6 -2.8, 2.5
7 47.5, 53.9 3.3, -3.3 -4.5, 3.7

ProtaStructure v3.0.4 Page 65

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

8 48.8, 55.2 6.9, -5.9 -4.3, 3.5

Critical Loading: 8 - ((G+Q)P2 *F2)

min Design
N 55.2 - 55.2 kN
M11 6.9 0.6 10.9 kN.m
M22 -4.3 -0.6 0.0 kN.m
Nmax 529.0
Concrete Cover = 40.0 mm
BS8110-
Cl.3.8.4.5

N/bhFcu 0.042
=
Beta = 0.95

Vd(1/2) = 2.5 / 3.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.82 / 0.82 N/mm2 Le1/b1 = 12.0 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.05 / 0.06 N/mm2 Le2/b2 = 12.0 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 66

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

Column Reinforcement Design

1C1 (G-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 350.8, 363.5 -19.7, 0.0 26.4, 0.0
2 243.6, 252.7 -13.6, 0.0 18.3, 0.0
3 280.9, 293.6 -9.7, 0.0 27.9, 0.0
4 268.1, 280.8 -20.7, 0.0 12.6, 0.0
5 292.3, 303.2 -16.4, 0.0 21.9, 0.0
6 292.3, 303.2 -16.4, 0.0 21.9, 0.0
7 292.3, 303.2 -16.4, 0.0 21.9, 0.0

8 292.3, 303.2 -16.4, 0.0 21.9, 0.0

Critical Loading: 1 - (G*F)

min Design
N 363.5 - 363.5 kN
M11 -19.7 -5.5 -19.7 kN.m
M22 26.4 5.5 26.4 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 242.3 mm / 35.92 O

Vd(1/2) = 6.6 / 4.9 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.69 / 0.69 N/mm2 Le1/b1 = 10.8 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.08 / 0.06 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C1 (G-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 93.6, 106.0 -19.9, 27.7 34.0, -44.5
2 64.7, 73.5 -13.7, 19.2 23.5, -30.8
3 72.3, 84.7 -6.8, 10.5 34.8, -46.9
4 70.8, 83.2 -23.6, 32.2 17.2, -21.2
5 77.6, 88.2 -16.5, 23.0 28.2, -36.9
6 77.6, 88.2 -16.5, 23.0 28.2, -36.9
7 77.6, 88.2 -16.5, 23.0 28.2, -36.9

8 77.6, 88.2 -16.5, 23.0 28.2, -36.9

Critical Loading: 1 - (G*F)

min Design
N 106.0 - 106.0 kN
M11 27.7 1.6 27.7 kN.m
M22 -44.5 -1.6 -44.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 188.7 mm / 33.74 O

Vd(1/2) = 19.9 / 13.6 kN Short Column... As (Req): %1.07 963.55 mm2

vc'(1/2) = 0.74 / 0.74 N/mm2 Le1/b1 = 9.7 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.23 / 0.16 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C2 (G-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 712.8, 725.5 -33.5, 0.0 -3.1, 0.0
2 494.0, 503.0 -23.0, 0.0 -2.1, 0.0
3 489.4, 502.1 -13.9, 0.0 -14.6, 0.0
4 614.7, 627.4 -36.2, 0.0 10.3, 0.0
5 592.8, 603.6 -27.6, 0.0 -2.5, 0.0
6 592.8, 603.6 -27.6, 0.0 -2.5, 0.0
7 592.8, 603.6 -27.6, 0.0 -2.5, 0.0

8 592.8, 603.6 -27.6, 0.0 -2.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 725.5 - 725.5 kN
M11 -33.5 -10.9 -33.5 kN.m
M22 -3.1 -10.9 -10.9 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 295.8 mm / 21.41 O

Vd(1/2) = 3.5 / 5.5 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.78 / 0.78 N/mm2 Le1/b1 = 10.8 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.04 / 0.06 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C2 (G-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 161.2, 173.6 -30.6, 49.1 -4.8, 4.8
2 111.4, 120.2 -21.1, 33.8 -3.3, 3.3
3 110.1, 122.5 -13.5, 20.4 -19.6, 23.4
4 136.0, 148.4 -32.7, 53.3 12.5, -16.5
5 133.6, 144.3 -25.3, 40.5 -3.9, 3.9
6 133.6, 144.3 -25.3, 40.5 -3.9, 3.9
7 133.6, 144.3 -25.3, 40.5 -3.9, 3.9

8 133.6, 144.3 -25.3, 40.5 -3.9, 3.9

Critical Loading: 4 - (G+Q)

min Design
N 148.4 - 148.4 kN
M11 53.3 2.2 53.3 kN.m
M22 -16.5 -2.2 -16.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 400.1 mm / 68.82 O

Vd(1/2) = 10.5 / 21.0 kN Short Column... As (Req): %1.02 921.45 mm2

vc'(1/2) = 0.77 / 0.78 N/mm2 Le1/b1 = 9.7 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.12 / 0.25 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

ProtaStructure v3.0.4 Page 2

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C3 (G-4) (300/300)

(C20/25 / Grade 500 (Type 2))

NTop/Bot M11 Top/Bot M22 Top/Bot

No
(kN) (kN.m) (kN.m)
1 687.9, 700.6 -25.4, 0.0 -5.8, 0.0
2 477.2, 486.3 -17.5, 0.0 -4.1, 0.0
3 584.2, 596.9 -27.1, 0.0 0.9, 0.0
4 485.8, 498.5 -11.4, 0.0 -10.1, 0.0
5 572.7, 583.6 -21.0, 0.0 -4.9, 0.0
6 572.7, 583.6 -21.0, 0.0 -4.9, 0.0
7 572.7, 583.6 -21.0, 0.0 -4.9, 0.0
8 572.7, 583.6 -21.0, 0.0 -4.9, 0.0

Critical Loading: 1 - (G*F)

min Design
N 700.6 - 700.6 kN
M11 -25.4 -10.5 -25.4 kN.m
M22 -5.8 -10.5 -10.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 293.0 mm / 21.60 O

Vd(1/2) = 2.4 / 4.2 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.77 / 0.77 N/mm2 Le1/b1 = 10.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.03 / 0.05 N/mm2 Le2/b2 = 10.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C3 (G-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 168.1, 180.5 -37.3, 45.4 -2.0, 6.1
2 116.2, 125.1 -25.8, 31.4 -1.4, 4.3
3 143.4, 155.8 -38.1, 46.9 9.7, -7.0
4 113.9, 126.3 -18.9, 22.3 -12.6, 16.6
5 139.5, 150.1 -31.0, 37.6 -1.6, 5.1
6 139.5, 150.1 -31.0, 37.6 -1.6, 5.1
7 139.5, 150.1 -31.0, 37.6 -1.6, 5.1

8 139.5, 150.1 -31.0, 37.6 -1.6, 5.1

Critical Loading: 3 - (G+Q *F1)

min Design
N 155.8 - 155.8 kN
M11 46.9 2.3 46.9 kN.m
M22 9.7 2.3 9.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 120.4 mm / 12.79 O

Vd(1/2) = 7.1 / 20.7 kN Short Column... As (Req): %0.77 690.12 mm2

vc'(1/2) = 0.67 / 0.70 N/mm2 Le1/b1 = 9.7 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.08 / 0.24 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 3

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C4 (G-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 876.1, 888.8 -47.2, 0.0 8.4, 0.0
2 611.2, 620.3 -32.9, 0.0 5.9, 0.0
3 759.2, 771.9 -43.0, 0.0 1.4, 0.0
4 629.8, 642.5 -31.5, 0.0 12.4, 0.0
5 733.5, 744.4 -39.5, 0.0 7.1, 0.0
6 733.5, 744.4 -39.5, 0.0 7.1, 0.0
7 733.5, 744.4 -39.5, 0.0 7.1, 0.0

8 733.5, 744.4 -39.5, 0.0 7.1, 0.0

Critical Loading: 1 - (G*F)

min Design
N 888.8 - 888.8 kN
M11 -47.2 -13.3 -47.2 kN.m
M22 8.4 13.3 13.3 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 848.1 mm / 70.97 O

Vd(1/2) = 3.0 / 7.8 kN Short Column... As (Req): %1.06 952.60 mm2

vc'(1/2) = 0.92 / 0.92 N/mm2 Le1/b1 = 10.4 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.03 / 0.09 N/mm2 Le2/b2 = 10.6 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

2C4 (G-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 202.6, 215.0 -58.6, 77.4 4.2, -11.5
2 140.1, 149.0 -40.6, 53.9 2.9, -8.1
3 175.1, 187.5 -57.6, 72.5 -10.1, 2.2
4 135.6, 148.0 -33.2, 48.9 16.8, -21.0
5 168.1, 178.8 -48.8, 64.6 3.5, -9.7
6 168.1, 178.8 -48.8, 64.6 3.5, -9.7
7 168.1, 178.8 -48.8, 64.6 3.5, -9.7

8 168.1, 178.8 -48.8, 64.6 3.5, -9.7

Critical Loading: 1 - (G*F)

min Design
N 215.0 - 215.0 kN
M11 77.4 3.2 77.4 kN.m
M22 -11.5 -3.2 -11.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 777.7 mm / 78.87 O

Vd(1/2) = 9.2 / 33.2 kN Short Column... As (Req): %1.92 1728.04 mm2

vc'(1/2) = 0.97 / 1.01 N/mm2 Le1/b1 = 9.7 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.11 / 0.39 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

ProtaStructure v3.0.4 Page 4

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C5 (G-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 435.1, 447.8 -33.3, 0.0 -24.5, 0.0
2 303.3, 312.3 -23.2, 0.0 -17.1, 0.0
3 359.4, 372.1 -32.8, 0.0 -18.8, 0.0
4 329.6, 342.3 -19.6, 0.0 -20.2, 0.0
5 363.9, 374.8 -27.9, 0.0 -20.5, 0.0
6 363.9, 374.8 -27.9, 0.0 -20.5, 0.0
7 363.9, 374.8 -27.9, 0.0 -20.5, 0.0

8 363.9, 374.8 -27.9, 0.0 -20.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 447.8 - 447.8 kN
M11 -33.3 -6.7 -33.3 kN.m
M22 -24.5 -6.7 -24.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 284.0 mm / 39.36 O

Vd(1/2) = 4.1 / 7.8 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.70 / 0.72 N/mm2 Le1/b1 = 10.4 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.05 / 0.09 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C5 (G-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 115.4, 127.8 -44.5, 55.6 -33.6, 40.7
2 79.7, 88.6 -30.8, 38.6 -23.3, 28.4
3 92.0, 104.4 -45.7, 55.9 -19.4, 27.4
4 84.5, 96.9 -22.9, 30.9 -32.6, 36.8
5 95.7, 106.3 -37.0, 46.4 -28.0, 34.0
6 95.7, 106.3 -37.0, 46.4 -28.0, 34.0
7 95.7, 106.3 -37.0, 46.4 -28.0, 34.0

8 95.7, 106.3 -37.0, 46.4 -28.0, 34.0

Critical Loading: 1 - (G*F)

min Design
N 127.8 - 127.8 kN
M11 55.6 1.9 55.6 kN.m
M22 40.7 1.9 40.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 225.8 mm / 37.22 O

Vd(1/2) = 16.9 / 24.8 kN Short Column... As (Req): %1.97 1770.50 mm2

vc'(1/2) = 0.93 / 0.94 N/mm2 Le1/b1 = 9.7 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.20 / 0.29 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

ProtaStructure v3.0.4 Page 5

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C6 (F-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 645.9, 658.6 7.3, 0.0 38.4, 0.0
2 446.9, 456.0 5.1, 0.0 26.2, 0.0
3 563.8, 576.5 -1.6, 0.0 43.5, 0.0
4 431.6, 444.3 12.9, 0.0 12.8, 0.0
5 536.3, 547.2 6.1, 0.0 31.5, 0.0
6 536.3, 547.2 6.1, 0.0 31.5, 0.0
7 536.3, 547.2 6.1, 0.0 31.5, 0.0

8 536.3, 547.2 6.1, 0.0 31.5, 0.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 576.5 - 576.5 kN
M11 -1.6 -8.6 -8.6 kN.m
M22 43.5 8.6 43.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 228.0 mm / 15.32 O

Vd(1/2) = 10.4 / 3.1 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.80 / 0.75 N/mm2 Le1/b1 = 10.7 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.12 / 0.04 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C6 (F-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 161.0, 173.4 11.7, -15.6 39.1, -59.5
2 111.2, 120.1 8.1, -10.8 26.9, -40.7
3 136.3, 148.7 -0.2, -1.1 40.0, -65.0
4 109.5, 121.9 18.0, -22.8 18.9, -23.1
5 133.5, 144.1 9.7, -12.9 32.3, -48.9
6 133.5, 144.1 9.7, -12.9 32.3, -48.9
7 133.5, 144.1 9.7, -12.9 32.3, -48.9

8 133.5, 144.1 9.7, -12.9 32.3, -48.9

Critical Loading: 3 - (G+Q *F1)

min Design
N 148.7 - 148.7 kN
M11 -1.1 -2.2 -2.2 kN.m
M22 -65.0 -2.2 -65.0 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 2626.1 mm / 87.91 O

Vd(1/2) = 25.6 / 10.0 kN Short Column... As (Req): %1.29 1164.71 mm2

vc'(1/2) = 0.78 / 0.77 N/mm2 Le1/b1 = 9.1 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.30 / 0.12 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

ProtaStructure v3.0.4 Page 6

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C7 (F-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 1247.9, 1260.6 9.8, 0.0 3.8, 0.0
2 860.1, 869.2 6.8, 0.0 2.8, 0.0
3 929.4, 942.1 -4.7, 0.0 -17.9, 0.0
4 963.5, 976.2 19.7, 0.0 24.7, 0.0
5 1032.2, 1043.0 8.1, 0.0 3.3, 0.0
6 1032.2, 1043.0 8.1, 0.0 3.3, 0.0
7 1032.2, 1043.0 8.1, 0.0 3.3, 0.0

8 1032.2, 1043.0 8.1, 0.0 3.3, 0.0

Critical Loading: 1 - (G*F)

min Design
N 1260.6 - 1260.6 kN
M11 9.8 18.9 18.9 kN.m
M22 3.8 18.9 18.9 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 536.6 mm / 45.00 O

Vd(1/2) = 5.9 / 4.7 kN Short Column... As (Req): %1.38 1237.60 mm2

vc'(1/2) = 1.05 / 1.05 N/mm2 Le1/b1 = 10.7 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.07 / 0.05 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

2C7 (F-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 217.3, 229.7 10.2, -15.3 1.9, -5.8
2 150.2, 159.1 7.0, -10.6 1.4, -4.2
3 166.5, 178.9 -4.0, 6.3 -18.2, 26.5
4 166.2, 178.6 19.6, -29.7 21.6, -36.7
5 180.3, 190.9 8.5, -12.7 1.6, -5.0
6 180.3, 190.9 8.5, -12.7 1.6, -5.0
7 180.3, 190.9 8.5, -12.7 1.6, -5.0

8 180.3, 190.9 8.5, -12.7 1.6, -5.0

Critical Loading: 4 - (G+Q)

min Design
N 178.6 - 178.6 kN
M11 -29.7 -2.7 -29.7 kN.m
M22 -36.7 -2.7 -36.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 262.2 mm / 50.44 O

Vd(1/2) = 14.2 / 12.0 kN Short Column... As (Req): %0.78 702.16 mm2

vc'(1/2) = 0.70 / 0.70 N/mm2 Le1/b1 = 9.1 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.17 / 0.14 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 7

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C8 (F-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 1246.7, 1259.4 7.9, 0.0 -47.9, 0.0
2 862.4, 871.5 5.5, 0.0 -33.0, 0.0
3 995.7, 1008.4 13.1, 0.0 -19.6, 0.0
4 920.1, 932.8 -0.9, 0.0 -52.8, 0.0
5 1034.9, 1045.8 6.6, 0.0 -39.6, 0.0
6 1034.9, 1045.8 6.6, 0.0 -39.6, 0.0
7 1034.9, 1045.8 6.6, 0.0 -39.6, 0.0

8 1034.9, 1045.8 6.6, 0.0 -39.6, 0.0

Critical Loading: 1 - (G*F)

min Design
N 1259.4 - 1259.4 kN
M11 7.9 18.9 18.9 kN.m
M22 -47.9 -18.9 -47.9 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 329.8 mm / 22.06 O

Vd(1/2) = 12.6 / 1.3 kN Short Column... As (Req): %2.27 2040.04 mm2

vc'(1/2) = 1.21 / 1.19 N/mm2 Le1/b1 = 10.6 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.15 / 0.02 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

2C8 (F-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 240.6, 253.0 6.8, -10.4 -41.0, 68.2
2 166.3, 175.1 4.7, -7.2 -28.3, 47.0
3 191.0, 203.4 15.5, -20.6 -19.2, 28.7
4 176.8, 189.2 -5.1, 4.8 -42.9, 74.5
5 199.5, 210.1 5.6, -8.6 -33.9, 56.4
6 199.5, 210.1 5.6, -8.6 -33.9, 56.4
7 199.5, 210.1 5.6, -8.6 -33.9, 56.4

8 199.5, 210.1 5.6, -8.6 -33.9, 56.4

Critical Loading: 4 - (G+Q)

min Design
N 189.2 - 189.2 kN
M11 -5.1 -2.8 -5.1 kN.m
M22 74.5 2.8 74.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 126.0 mm / 4.60 O

Vd(1/2) = 28.6 / 8.8 kN Short Column... As (Req): %1.73 1555.40 mm2

vc'(1/2) = 0.86 / 0.88 N/mm2 Le1/b1 = 9.1 < 15.0 √ As (Sup): %1.79 1608.50 mm2
v(1/2) = 0.33 / 0.10 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H16
Links = H8-175

ProtaStructure v3.0.4 Page 8

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C9 (F-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 1363.6, 1376.3 5.2, 0.0 0.4, 0.0
2 948.8, 957.9 3.6, 0.0 0.3, 0.0
3 1225.4, 1238.1 6.1, 0.0 0.2, 0.0
4 914.6, 927.3 2.1, 0.0 0.4, 0.0
5 1138.6, 1149.5 4.3, 0.0 0.3, 0.0
6 1138.6, 1149.5 4.3, 0.0 0.3, 0.0
7 1138.6, 1149.5 4.3, 0.0 0.3, 0.0

8 1138.6, 1149.5 4.3, 0.0 0.3, 0.0

Critical Loading: 1 - (G*F)

min Design
N 1376.3 - 1376.3 kN
M11 5.2 20.6 20.6 kN.m
M22 0.4 20.6 20.6 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 532.0 mm / 45.09 O

Vd(1/2) = 0.1 / 0.5 kN Short Column... As (Req): %1.81 1630.29 mm2

vc'(1/2) = 1.21 / 1.21 N/mm2 Le1/b1 = 12.1 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.00 / 0.01 N/mm2 Le2/b2 = 11.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

2C9 (F-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 268.2, 280.6 10.5, -10.2 0.2, -1.6
2 185.5, 194.4 7.3, -7.1 0.1, -1.1
3 244.2, 256.6 16.0, -14.1 0.2, -1.4
4 167.1, 179.5 0.6, -2.2 0.1, -1.1
5 222.6, 233.2 8.8, -8.6 0.2, -1.3
6 222.6, 233.2 8.8, -8.6 0.2, -1.3
7 222.6, 233.2 8.8, -8.6 0.2, -1.3

8 222.6, 233.2 8.8, -8.6 0.2, -1.3

Critical Loading: 1 - (G*F)

min Design
N 280.6 - 280.6 kN
M11 10.5 4.2 10.5 kN.m
M22 -1.6 -4.2 -4.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 162.0 mm / 21.42 O

Vd(1/2) = 0.3 / 7.3 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.66 / 0.77 N/mm2 Le1/b1 = 10.1 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.00 / 0.09 N/mm2 Le2/b2 = 9.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 9

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C10 (F-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 823.5, 836.2 6.7, 0.0 -2.7, 0.0
2 573.1, 582.1 4.7, 0.0 -1.9, 0.0
3 724.0, 736.7 11.6, 0.0 -2.5, 0.0
4 570.1, 582.8 -0.9, 0.0 -1.7, 0.0
5 687.7, 698.6 5.6, 0.0 -2.2, 0.0
6 687.7, 698.6 5.6, 0.0 -2.2, 0.0
7 687.7, 698.6 5.6, 0.0 -2.2, 0.0

8 687.7, 698.6 5.6, 0.0 -2.2, 0.0

Critical Loading: 1 - (G*F)

min Design
N 836.2 - 836.2 kN
M11 6.7 12.5 12.5 kN.m
M22 -2.7 -12.5 -12.5 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 356.0 mm / 26.67 O

Vd(1/2) = 0.4 / 1.1 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.81 / 0.81 N/mm2 Le1/b1 = 12.1 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.00 / 0.01 N/mm2 Le2/b2 = 11.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C10 (F-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 179.5, 191.9 13.0, -13.7 -1.2, 2.2
2 124.0, 132.9 9.0, -9.5 -0.8, 1.5
3 155.4, 167.8 21.3, -22.5 -1.2, 2.0
4 118.7, 131.1 -1.2, 1.1 -0.6, 1.4
5 148.8, 159.4 10.8, -11.5 -1.0, 1.8
6 148.8, 159.4 10.8, -11.5 -1.0, 1.8
7 148.8, 159.4 10.8, -11.5 -1.0, 1.8

8 148.8, 159.4 10.8, -11.5 -1.0, 1.8

Critical Loading: 1 - (G*F)

min Design
N 191.9 - 191.9 kN
M11 -13.7 -2.9 -13.7 kN.m
M22 2.2 2.9 2.9 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 156.0 mm / 27.93 O

Vd(1/2) = 0.5 / 10.7 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.66 / 0.71 N/mm2 Le1/b1 = 10.1 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.01 / 0.13 N/mm2 Le2/b2 = 9.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 10

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C11 (E-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 453.5, 466.2 6.5, 0.0 37.1, 0.0
2 314.3, 323.4 4.5, 0.0 25.5, 0.0
3 438.9, 451.6 7.6, 0.0 40.7, 0.0
4 265.1, 277.8 2.2, 0.0 14.5, 0.0
5 377.2, 388.1 5.3, 0.0 30.5, 0.0
6 377.2, 388.1 5.3, 0.0 30.5, 0.0
7 377.2, 388.1 5.3, 0.0 30.5, 0.0

8 377.2, 388.1 5.3, 0.0 30.5, 0.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 451.6 - 451.6 kN
M11 7.6 6.8 7.6 kN.m
M22 40.7 6.8 40.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 744.7 mm / 75.50 O

Vd(1/2) = 9.7 / 0.5 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.76 / 0.69 N/mm2 Le1/b1 = 10.6 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.11 / 0.01 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C11 (E-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 64.9, 77.3 28.9, -23.1 37.9, -57.3
2 44.8, 53.7 20.0, -16.0 26.1, -39.4
3 53.9, 66.3 31.3, -26.0 40.2, -62.7
4 45.1, 57.5 12.9, -9.3 17.1, -23.0
5 53.8, 64.4 24.0, -19.2 31.3, -47.2
6 53.8, 64.4 24.0, -19.2 31.3, -47.2
7 53.8, 64.4 24.0, -19.2 31.3, -47.2

8 53.8, 64.4 24.0, -19.2 31.3, -47.2

Critical Loading: 3 - (G+Q *F1)

min Design
N 66.3 - 66.3 kN
M11 31.3 1.0 31.3 kN.m
M22 -62.7 -1.0 -62.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 188.4 mm / 28.68 O

Vd(1/2) = 25.1 / 14.0 kN Short Column... As (Req): %2.01 1805.43 mm2

vc'(1/2) = 0.90 / 0.90 N/mm2 Le1/b1 = 9.0 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.29 / 0.16 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

ProtaStructure v3.0.4 Page 11

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C12 (E-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 945.5, 958.2 11.2, 0.0 -7.2, 0.0
2 652.2, 661.3 7.7, 0.0 -4.9, 0.0
3 770.2, 782.9 14.3, 0.0 -23.1, 0.0
4 668.9, 681.6 2.4, 0.0 12.6, 0.0
5 782.6, 793.5 9.2, 0.0 -5.9, 0.0
6 782.6, 793.5 9.2, 0.0 -5.9, 0.0
7 782.6, 793.5 9.2, 0.0 -5.9, 0.0

8 782.6, 793.5 9.2, 0.0 -5.9, 0.0

Critical Loading: 1 - (G*F)

min Design
N 958.2 - 958.2 kN
M11 11.2 14.4 14.4 kN.m
M22 -7.2 -14.4 -14.4 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 506.9 mm / 44.94 O

Vd(1/2) = 3.0 / 1.8 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.84 / 0.84 N/mm2 Le1/b1 = 10.6 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C12 (E-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 188.6, 201.0 16.4, -19.7 -7.2, 10.2
2 130.3, 139.2 11.3, -13.5 -4.9, 7.0
3 147.6, 160.0 19.1, -24.5 -23.4, 34.0
4 140.8, 153.2 5.6, -4.9 12.7, -19.0
5 156.4, 167.0 13.5, -16.2 -5.9, 8.4
6 156.4, 167.0 13.5, -16.2 -5.9, 8.4
7 156.4, 167.0 13.5, -16.2 -5.9, 8.4

8 156.4, 167.0 13.5, -16.2 -5.9, 8.4

Critical Loading: 3 - (G+Q *F1)

min Design
N 160.0 - 160.0 kN
M11 -24.5 -2.4 -24.5 kN.m
M22 34.0 2.4 34.0 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 196.9 mm / 36.53 O

Vd(1/2) = 14.0 / 10.7 kN Short Column... As (Req): %0.62 557.86 mm2

vc'(1/2) = 0.69 / 0.70 N/mm2 Le1/b1 = 9.0 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.16 / 0.12 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 12

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C13 (E-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 900.2, 912.9 22.3, 0.0 -3.8, 0.0
2 622.6, 631.6 15.4, 0.0 -2.6, 0.0
3 654.8, 667.5 14.7, 0.0 7.8, 0.0
4 728.4, 741.1 19.5, 0.0 -13.1, 0.0
5 747.1, 758.0 18.5, 0.0 -3.1, 0.0
6 747.1, 758.0 18.5, 0.0 -3.1, 0.0
7 747.1, 758.0 18.5, 0.0 -3.1, 0.0

8 747.1, 758.0 18.5, 0.0 -3.1, 0.0

Critical Loading: 1 - (G*F)

min Design
N 912.9 - 912.9 kN
M11 22.3 13.7 22.3 kN.m
M22 -3.8 -13.7 -13.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 702.1 mm / 62.18 O

Vd(1/2) = 1.9 / 3.7 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.84 / 0.83 N/mm2 Le1/b1 = 10.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.02 / 0.04 N/mm2 Le2/b2 = 10.6 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C13 (E-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 189.1, 201.5 29.5, -36.2 -1.6, 3.9
2 130.6, 139.5 20.4, -25.0 -1.1, 2.6
3 143.3, 155.7 20.1, -24.5 12.7, -15.6
4 145.5, 157.9 25.0, -31.0 -14.6, 20.7
5 156.8, 167.4 24.4, -30.0 -1.3, 3.1
6 156.8, 167.4 24.4, -30.0 -1.3, 3.1
7 156.8, 167.4 24.4, -30.0 -1.3, 3.1

8 156.8, 167.4 24.4, -30.0 -1.3, 3.1

Critical Loading: 4 - (G+Q)

min Design
N 157.9 - 157.9 kN
M11 -31.0 -2.4 -31.0 kN.m
M22 20.7 2.4 20.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 269.5 mm / 55.75 O

Vd(1/2) = 8.6 / 16.0 kN Short Column... As (Req): %0.46 418.33 mm2

vc'(1/2) = 0.69 / 0.73 N/mm2 Le1/b1 = 9.0 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.10 / 0.19 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 13

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C14 (E-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 1559.1, 1571.8 -10.6, 0.0 6.0, 0.0
2 1080.8, 1089.9 -7.1, 0.0 4.2, 0.0
3 1329.9, 1342.6 -12.0, 0.0 -3.8, 0.0
4 1083.9, 1096.6 -2.5, 0.0 13.2, 0.0
5 1297.0, 1307.9 -8.5, 0.0 5.0, 0.0
6 1297.0, 1307.9 -8.5, 0.0 5.0, 0.0
7 1297.0, 1307.9 -8.5, 0.0 5.0, 0.0

8 1297.0, 1307.9 -8.5, 0.0 5.0, 0.0

Critical Loading: 1 - (G*F)

min Design
N 1571.8 - 1571.8 kN
M11 -10.6 -23.6 -23.6 kN.m
M22 6.0 23.6 23.6 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 540.1 mm / 45.00 O

Vd(1/2) = 3.2 / 1.7 kN Short Column... As (Req): %2.49 2241.75 mm2

vc'(1/2) = 1.28 / 1.28 N/mm2 Le1/b1 = 10.2 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.04 / 0.02 N/mm2 Le2/b2 = 10.6 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

2C14 (E-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 309.5, 321.9 -20.8, 21.5 4.3, -9.2
2 213.9, 222.7 -14.2, 14.6 3.0, -6.4
3 248.6, 261.0 -22.9, 23.9 -9.8, 7.3
4 224.3, 236.6 -7.6, 6.7 16.6, -21.7
5 256.6, 267.3 -17.1, 17.5 3.6, -7.7
6 256.6, 267.3 -17.1, 17.5 3.6, -7.7
7 256.6, 267.3 -17.1, 17.5 3.6, -7.7

8 256.6, 267.3 -17.1, 17.5 3.6, -7.7

Critical Loading: 1 - (G*F)

min Design
N 321.9 - 321.9 kN
M11 21.5 4.8 21.5 kN.m
M22 -9.2 -4.8 -9.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 244.0 mm / 39.50 O

Vd(1/2) = 9.4 / 11.4 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.75 / 0.79 N/mm2 Le1/b1 = 9.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.11 / 0.13 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 14

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C15 (E-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 826.6, 839.3 -13.7, 0.0 -30.4, 0.0
2 574.2, 583.2 -9.4, 0.0 -21.1, 0.0
3 645.9, 658.6 -18.6, 0.0 -19.6, 0.0
4 644.6, 657.3 -2.2, 0.0 -27.3, 0.0
5 689.0, 699.9 -11.3, 0.0 -25.3, 0.0
6 689.0, 699.9 -11.3, 0.0 -25.3, 0.0
7 689.0, 699.9 -11.3, 0.0 -25.3, 0.0

8 689.0, 699.9 -11.3, 0.0 -25.3, 0.0

Critical Loading: 1 - (G*F)

min Design
N 839.3 - 839.3 kN
M11 -13.7 -12.6 -13.7 kN.m
M22 -30.4 -12.6 -30.4 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 721.6 mm / 65.39 O

Vd(1/2) = 5.0 / 4.4 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.81 / 0.84 N/mm2 Le1/b1 = 10.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.06 / 0.05 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C15 (E-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 204.9, 217.3 -21.4, 24.2 -39.3, 49.6
2 141.6, 150.5 -14.7, 16.7 -27.2, 34.3
3 157.0, 169.4 -29.1, 33.4 -22.4, 29.7
4 156.2, 168.6 -3.2, 3.4 -37.8, 46.5
5 169.9, 180.6 -17.7, 20.1 -32.6, 41.2
6 169.9, 180.6 -17.7, 20.1 -32.6, 41.2
7 169.9, 180.6 -17.7, 20.1 -32.6, 41.2

8 169.9, 180.6 -17.7, 20.1 -32.6, 41.2

Critical Loading: 1 - (G*F)

min Design
N 217.3 - 217.3 kN
M11 24.2 3.3 24.2 kN.m
M22 49.6 3.3 49.6 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 343.7 mm / 60.70 O

Vd(1/2) = 20.6 / 15.2 kN Short Column... As (Req): %0.98 878.44 mm2

vc'(1/2) = 0.80 / 0.81 N/mm2 Le1/b1 = 9.2 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.24 / 0.18 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

ProtaStructure v3.0.4 Page 15

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C16 (C-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 462.1, 474.8 6.4, 0.0 16.2, 0.0
2 320.3, 329.4 4.4, 0.0 11.3, 0.0
3 436.6, 449.3 3.3, 0.0 19.1, 0.0
4 281.4, 294.1 6.7, 0.0 6.9, 0.0
5 384.4, 395.3 5.3, 0.0 13.6, 0.0
6 384.4, 395.3 5.3, 0.0 13.6, 0.0
7 384.4, 395.3 5.3, 0.0 13.6, 0.0

8 384.4, 395.3 5.3, 0.0 13.6, 0.0

Critical Loading: 1 - (G*F)

min Design
N 474.8 - 474.8 kN
M11 6.4 7.1 7.1 kN.m
M22 16.2 7.1 16.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 255.3 mm / 30.67 O

Vd(1/2) = 1.7 / 1.6 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.69 / 0.69 N/mm2 Le1/b1 = 10.7 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.02 / 0.02 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C16 (C-1) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 223.8, 236.2 -41.2, 11.5 27.2, -31.0
2 154.7, 163.5 -28.5, 8.0 18.9, -21.7
3 215.2, 227.6 -46.5, 16.8 30.9, -36.7
4 126.8, 139.2 -16.4, 0.7 11.3, -12.3
5 185.6, 196.2 -34.1, 9.5 22.6, -26.0
6 185.6, 196.2 -34.1, 9.5 22.6, -26.0
7 185.6, 196.2 -34.1, 9.5 22.6, -26.0

8 185.6, 196.2 -34.1, 9.5 22.6, -26.0

Critical Loading: 3 - (G+Q *F1)

min Design
N 227.6 - 227.6 kN
M11 -46.5 -3.4 -46.5 kN.m
M22 -36.7 -3.4 -36.7 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 234.2 mm / 39.18 O

Vd(1/2) = 16.5 / 15.4 kN Short Column... As (Req): %1.18 1063.61 mm2

vc'(1/2) = 0.85 / 0.80 N/mm2 Le1/b1 = 8.9 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.19 / 0.18 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

ProtaStructure v3.0.4 Page 16

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C17 (C-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 778.9, 791.6 4.5, 0.0 12.2, 0.0
2 539.1, 548.1 3.1, 0.0 8.3, 0.0
3 607.8, 620.5 0.4, 0.0 -1.1, 0.0
4 592.5, 605.2 6.6, 0.0 18.7, 0.0
5 646.9, 657.8 3.7, 0.0 10.0, 0.0
6 646.9, 657.8 3.7, 0.0 10.0, 0.0
7 646.9, 657.8 3.7, 0.0 10.0, 0.0

8 646.9, 657.8 3.7, 0.0 10.0, 0.0

Critical Loading: 1 - (G*F)

min Design
N 791.6 - 791.6 kN
M11 4.5 11.9 11.9 kN.m
M22 12.2 11.9 12.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 333.5 mm / 24.83 O

Vd(1/2) = 4.5 / 0.7 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.82 / 0.79 N/mm2 Le1/b1 = 10.7 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.05 / 0.01 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C17 (C-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 183.8, 196.2 6.6, -8.0 8.3, -17.7
2 127.0, 135.9 4.5, -5.5 5.7, -12.1
3 138.3, 150.7 1.8, -1.7 -8.3, 3.2
4 142.4, 154.8 8.1, -10.5 20.7, -29.0
5 152.4, 163.0 5.4, -6.6 6.8, -14.5
6 152.4, 163.0 5.4, -6.6 6.8, -14.5
7 152.4, 163.0 5.4, -6.6 6.8, -14.5

8 152.4, 163.0 5.4, -6.6 6.8, -14.5

Critical Loading: 4 - (G+Q)

min Design
N 154.8 - 154.8 kN
M11 -10.5 -2.3 -10.5 kN.m
M22 -29.0 -2.3 -29.0 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 366.7 mm / 71.64 O

Vd(1/2) = 12.1 / 4.5 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.69 / 0.69 N/mm2 Le1/b1 = 8.9 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.14 / 0.05 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 17

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C18 (A-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 544.3, 557.0 -1.9, 0.0 3.6, 0.0
2 379.4, 388.5 -1.3, 0.0 2.3, 0.0
3 484.0, 496.7 -1.8, 0.0 -1.4, 0.0
4 377.8, 390.5 -1.1, 0.0 5.6, 0.0
5 455.3, 466.2 -1.6, 0.0 2.8, 0.0
6 455.3, 466.2 -1.6, 0.0 2.8, 0.0
7 455.3, 466.2 -1.6, 0.0 2.8, 0.0

8 455.3, 466.2 -1.6, 0.0 2.8, 0.0

Critical Loading: 1 - (G*F)

min Design
N 557.0 - 557.0 kN
M11 -1.9 -8.4 -8.4 kN.m
M22 3.6 8.4 8.4 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 233.0 mm / 17.07 O

Vd(1/2) = 1.3 / 0.3 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.73 / 0.73 N/mm2 Le1/b1 = 11.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.02 / 0.00 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C18 (A-2) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 167.6, 180.0 8.2, -2.2 -25.0, 4.9
2 115.8, 124.7 5.7, -1.5 -17.4, 3.6
3 139.9, 152.3 6.8, -2.0 -36.2, 15.2
4 116.1, 128.5 5.6, -1.4 -2.5, -5.9
5 139.0, 149.6 6.8, -1.8 -20.8, 4.3
6 139.0, 149.6 6.8, -1.8 -20.8, 4.3
7 139.0, 149.6 6.8, -1.8 -20.8, 4.3

8 139.0, 149.6 6.8, -1.8 -20.8, 4.3

Critical Loading: 3 - (G+Q *F1)

min Design
N 152.3 - 152.3 kN
M11 6.8 2.3 6.8 kN.m
M22 -36.2 -2.3 -36.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 102.6 mm / 10.26 O

Vd(1/2) = 12.5 / 1.7 kN Short Column... As (Req): %0.47 421.66 mm2

vc'(1/2) = 0.66 / 0.64 N/mm2 Le1/b1 = 9.2 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.15 / 0.02 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 18

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C19 (A-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 383.2, 395.9 2.3, 0.0 -10.3, 0.0
2 267.0, 276.1 1.6, 0.0 -7.1, 0.0
3 318.9, 331.6 1.8, 0.0 -4.6, 0.0
4 287.9, 300.6 1.8, 0.0 -10.6, 0.0
5 320.4, 331.3 1.9, 0.0 -8.5, 0.0
6 320.4, 331.3 1.9, 0.0 -8.5, 0.0
7 320.4, 331.3 1.9, 0.0 -8.5, 0.0

8 320.4, 331.3 1.9, 0.0 -8.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 395.9 - 395.9 kN
M11 2.3 5.9 5.9 kN.m
M22 -10.3 -5.9 -10.3 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 168.5 mm / 12.20 O

Vd(1/2) = 2.5 / 0.4 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.70 / 0.69 N/mm2 Le1/b1 = 10.6 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.03 / 0.00 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C19 (A-4) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 104.5, 116.9 2.6, -2.4 1.1, 6.3
2 72.2, 81.0 1.8, -1.6 0.8, 4.3
3 78.9, 91.3 2.6, -2.5 13.1, -5.9
4 80.7, 93.1 1.3, -1.1 -11.0, 14.8
5 86.6, 97.2 2.1, -2.0 1.0, 5.1
6 86.6, 97.2 2.1, -2.0 1.0, 5.1
7 86.6, 97.2 2.1, -2.0 1.0, 5.1

8 86.6, 97.2 2.1, -2.0 1.0, 5.1

Critical Loading: 1 - (G*F)

min Design
N 116.9 - 116.9 kN
M11 2.6 1.8 2.6 kN.m
M22 6.3 1.8 6.3 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 83.2 mm / 12.56 O

Vd(1/2) = 6.3 / 0.8 kN Short Column... As (Req): %0.40 (min) 360.00 mm2
vc'(1/2) = 0.65 / 0.64 N/mm2 Le1/b1 = 9.0 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.07 / 0.01 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 19

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C20 (A-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 711.9, 724.6 56.0, 0.0 6.4, 0.0
2 493.4, 502.5 38.6, 0.0 4.4, 0.0
3 599.5, 612.2 52.8, 0.0 -3.7, 0.0
4 503.9, 516.6 31.8, 0.0 13.3, 0.0
5 592.1, 603.0 46.3, 0.0 5.3, 0.0
6 592.1, 603.0 46.3, 0.0 5.3, 0.0
7 592.1, 603.0 46.3, 0.0 5.3, 0.0

8 592.1, 603.0 46.3, 0.0 5.3, 0.0

Critical Loading: 1 - (G*F)

min Design
N 724.6 - 724.6 kN
M11 56.0 10.9 56.0 kN.m
M22 6.4 10.9 10.9 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 241.8 mm / 14.25 O

Vd(1/2) = 3.2 / 12.6 kN Short Column... As (Req): %1.01 904.71 mm2

vc'(1/2) = 0.88 / 0.91 N/mm2 Le1/b1 = 10.9 < 15.0 √ As (Sup): %1.40 1256.64 mm2
v(1/2) = 0.04 / 0.15 N/mm2 Le2/b2 = 10.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H20
Links = H8-225

2C20 (A-9) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 192.7, 205.1 71.2, -91.8 9.0, -14.8
2 133.2, 142.0 49.1, -63.3 6.2, -10.2
3 162.5, 174.9 67.0, -86.8 -5.0, 2.1
4 131.9, 144.3 41.4, -52.5 18.8, -24.5
5 159.8, 170.4 59.0, -76.0 7.5, -12.2
6 159.8, 170.4 59.0, -76.0 7.5, -12.2
7 159.8, 170.4 59.0, -76.0 7.5, -12.2

8 159.8, 170.4 59.0, -76.0 7.5, -12.2

Critical Loading: 1 - (G*F)

min Design
N 205.1 - 205.1 kN
M11 -91.8 -3.1 -91.8 kN.m
M22 -14.8 -3.1 -14.8 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 159.5 mm / 11.91 O

Vd(1/2) = 10.6 / 39.8 kN Short Column... As (Req): %2.54 2288.84 mm2

vc'(1/2) = 0.96 / 1.00 N/mm2 Le1/b1 = 9.8 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.12 / 0.46 N/mm2 Le2/b2 = 9.2 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

ProtaStructure v3.0.4 Page 20

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C21 (A-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 416.0, 428.7 37.6, 0.0 -30.2, 0.0
2 289.0, 298.1 26.1, 0.0 -20.9, 0.0
3 336.0, 348.7 39.5, 0.0 -16.9, 0.0
4 315.3, 328.0 19.1, 0.0 -29.5, 0.0
5 346.8, 357.7 31.4, 0.0 -25.1, 0.0
6 346.8, 357.7 31.4, 0.0 -25.1, 0.0
7 346.8, 357.7 31.4, 0.0 -25.1, 0.0

8 346.8, 357.7 31.4, 0.0 -25.1, 0.0

Critical Loading: 1 - (G*F)

min Design
N 428.7 - 428.7 kN
M11 37.6 6.4 37.6 kN.m
M22 -30.2 -6.4 -30.2 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 332.0 mm / 49.48 O

Vd(1/2) = 7.0 / 9.4 kN Short Column... As (Req): %0.53 473.13 mm2

vc'(1/2) = 0.71 / 0.72 N/mm2 Le1/b1 = 10.9 < 15.0 √ As (Sup): %0.89 804.25 mm2
v(1/2) = 0.08 / 0.11 N/mm2 Le2/b2 = 10.9 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

2C21 (A-11) (300/300)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 118.5, 130.9 54.6, -65.7 -33.9, 43.8
2 81.9, 90.8 37.8, -45.5 -23.4, 30.3
3 94.1, 106.5 56.4, -68.1 -15.8, 20.9
4 87.1, 99.5 27.7, -33.6 -36.1, 46.4
5 98.3, 108.9 45.4, -54.7 -28.1, 36.4
6 98.3, 108.9 45.4, -54.7 -28.1, 36.4
7 98.3, 108.9 45.4, -54.7 -28.1, 36.4

8 98.3, 108.9 45.4, -54.7 -28.1, 36.4

Critical Loading: 1 - (G*F)

min Design
N 130.9 - 130.9 kN
M11 -65.7 -2.0 -65.7 kN.m
M22 43.8 2.0 43.8 kN.m
Nmax 1201.6
Concrete Cover = 40.0 mm
Neutral Axis: 316.6 mm / 54.79 O

Vd(1/2) = 20.1 / 30.4 kN Short Column... As (Req): %2.44 2197.21 mm2

vc'(1/2) = 0.93 / 0.94 N/mm2 Le1/b1 = 9.8 < 15.0 √ As (Sup): %2.79 2513.27 mm2
v(1/2) = 0.24 / 0.36 N/mm2 Le2/b2 = 9.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 8H20
Links = H8-225

ProtaStructure v3.0.4 Page 21

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

1C22 (A-1) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 151.4, 158.8 0.0, 0.0 6.5, 0.0
2 105.7, 111.0 0.0, 0.0 4.7, 0.0
3 153.4, 160.8 0.0, 0.0 7.0, 0.0
4 86.8, 94.3 0.0, 0.0 4.7, 0.0
5 126.8, 133.2 0.0, 0.0 5.6, 0.0
6 126.8, 133.2 0.0, 0.0 5.6, 0.0
7 126.8, 133.2 0.0, 0.0 5.6, 0.0

8 126.8, 133.2 0.0, 0.0 5.6, 0.0

Critical Loading: 1 - (G*F)

min Design
N 158.8 - 158.8 kN
M11 0.0 -1.8 -1.8 kN.m
M22 6.5 1.8 6.5 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 91.6 mm / 8.64 O

Vd(1/2) = 1.1 / 0.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.82 / 0.82 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.00 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C23 (D-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 234.4, 241.8 -0.6, 0.0 -1.8, 0.0
2 162.8, 168.1 -0.4, 0.0 -1.2, 0.0
3 176.8, 184.2 0.1, 0.0 -1.7, 0.0
4 190.2, 197.7 -1.0, 0.0 -0.9, 0.0
5 195.3, 201.7 -0.5, 0.0 -1.5, 0.0
6 195.3, 201.7 -0.5, 0.0 -1.5, 0.0
7 195.3, 201.7 -0.5, 0.0 -1.5, 0.0

8 195.3, 201.7 -0.5, 0.0 -1.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 241.8 - 241.8 kN
M11 -0.6 -2.8 -2.8 kN.m
M22 -1.8 -2.8 -2.8 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 134.4 mm / 12.76 O

Vd(1/2) = 0.3 / 0.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.00 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 22

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

2C23 (D-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 77.1, 84.4 -0.3, 1.2 -1.9, 2.4
2 53.2, 58.4 -0.2, 0.8 -1.3, 1.6
3 53.7, 61.0 1.0, -0.4 -1.7, 1.9
4 63.3, 70.6 -1.4, 2.2 -1.1, 1.6
5 63.8, 70.1 -0.3, 1.0 -1.6, 2.0
6 63.8, 70.1 -0.3, 1.0 -1.6, 2.0
7 63.8, 70.1 -0.3, 1.0 -1.6, 2.0

8 63.8, 70.1 -0.3, 1.0 -1.6, 2.0

Critical Loading: 1 - (G*F)

min Design
N 84.4 - 84.4 kN
M11 1.2 1.0 1.2 kN.m
M22 2.4 1.0 2.4 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 67.7 mm / 11.03 O

Vd(1/2) = 0.7 / 0.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.82 N/mm2 Le1/b1 = 11.4 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.01 N/mm2 Le2/b2 = 11.5 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C24 (D-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 318.2, 325.7 0.6, 0.0 4.3, 0.0
2 220.2, 225.5 0.4, 0.0 2.9, 0.0
3 196.5, 203.9 0.6, 0.0 2.1, 0.0
4 294.5, 301.9 0.3, 0.0 4.3, 0.0
5 264.2, 270.6 0.5, 0.0 3.5, 0.0
6 264.2, 270.6 0.5, 0.0 3.5, 0.0
7 264.2, 270.6 0.5, 0.0 3.5, 0.0

8 264.2, 270.6 0.5, 0.0 3.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 325.7 - 325.7 kN
M11 0.6 3.7 3.7 kN.m
M22 4.3 3.7 4.3 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 183.7 mm / 19.47 O

Vd(1/2) = 0.5 / 0.1 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.87 / 0.87 N/mm2 Le1/b1 = 13.8 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.00 N/mm2 Le2/b2 = 13.7 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 23

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

2C24 (D-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 80.3, 87.6 1.6, -1.2 6.8, -8.1
2 55.4, 60.6 1.1, -0.8 4.7, -5.6
3 50.3, 57.6 1.7, -1.5 4.1, -4.9
4 71.9, 79.2 0.7, -0.3 6.2, -7.4
5 66.5, 72.8 1.3, -1.0 5.6, -6.7
6 66.5, 72.8 1.3, -1.0 5.6, -6.7
7 66.5, 72.8 1.3, -1.0 5.6, -6.7

8 66.5, 72.8 1.3, -1.0 5.6, -6.7

Critical Loading: 1 - (G*F)

min Design
N 87.6 - 87.6 kN
M11 1.6 1.0 1.6 kN.m
M22 -8.1 -1.0 -8.1 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 60.4 mm / 7.23 O

Vd(1/2) = 3.6 / 0.8 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.83 N/mm2 Le1/b1 = 11.5 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.07 / 0.02 N/mm2 Le2/b2 = 11.4 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C25 (B-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 247.4, 254.8 1.6, 0.0 0.0, 0.0
2 172.0, 177.3 1.1, 0.0 0.0, 0.0
3 186.0, 193.4 0.9, 0.0 0.1, 0.0
4 202.3, 209.8 1.7, 0.0 0.1, 0.0
5 206.3, 212.7 1.4, 0.0 0.1, 0.0
6 206.3, 212.7 1.4, 0.0 0.1, 0.0
7 206.3, 212.7 1.4, 0.0 0.1, 0.0

8 206.3, 212.7 1.4, 0.0 0.1, 0.0

Critical Loading: 1 - (G*F)

min Design
N 254.8 - 254.8 kN
M11 1.6 2.9 2.9 kN.m
M22 0.0 2.9 2.9 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 141.1 mm / 13.47 O

Vd(1/2) = 0.0 / 0.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.00 / 0.01 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 24

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

2C25 (B-4) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 63.7, 71.0 1.9, -2.2 1.8, -1.8
2 44.0, 49.2 1.3, -1.5 1.3, -1.3
3 47.0, 54.3 1.1, -1.3 2.4, -2.4
4 49.9, 57.2 1.9, -2.2 0.5, -0.6
5 52.7, 59.0 1.6, -1.9 1.5, -1.5
6 52.7, 59.0 1.6, -1.9 1.5, -1.5
7 52.7, 59.0 1.6, -1.9 1.5, -1.5

8 52.7, 59.0 1.6, -1.9 1.5, -1.5

Critical Loading: 1 - (G*F)

min Design
N 71.0 - 71.0 kN
M11 -2.2 -0.8 -2.2 kN.m
M22 -1.8 -0.8 -1.8 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 56.5 mm / 8.24 O

Vd(1/2) = 1.2 / 0.7 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.82 / 0.82 N/mm2 Le1/b1 = 11.4 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.02 / 0.01 N/mm2 Le2/b2 = 11.5 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

1C26 (B-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 273.4, 280.8 0.0, 0.0 -1.8, 0.0
2 190.1, 195.5 0.0, 0.0 -1.3, 0.0
3 250.3, 257.8 -1.6, 0.0 -1.8, 0.0
4 179.4, 186.9 1.4, 0.0 -1.1, 0.0
5 228.2, 234.6 0.0, 0.0 -1.5, 0.0
6 228.2, 234.6 0.0, 0.0 -1.5, 0.0
7 228.2, 234.6 0.0, 0.0 -1.5, 0.0

8 228.2, 234.6 0.0, 0.0 -1.5, 0.0

Critical Loading: 1 - (G*F)

min Design
N 280.8 - 280.8 kN
M11 0.0 -3.2 -3.2 kN.m
M22 -1.8 -3.2 -3.2 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 154.6 mm / 14.88 O

Vd(1/2) = 0.3 / 0.3 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.86 / 0.86 N/mm2 Le1/b1 = 13.7 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.01 N/mm2 Le2/b2 = 13.8 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 25

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Column Reinforcement Design Calc. By: G L
Rev: 1 Checked By: H J

2C26 (B-6) (230/230)

(C20/25 / Grade 500 (Type 2))
NTop/Bot M11 Top/Bot M22 Top/Bot
No
(kN) (kN.m) (kN.m)
1 88.4, 95.7 -2.0, 1.2 -1.7, 1.8
2 61.0, 66.2 -1.4, 0.8 -1.1, 1.3
3 80.2, 87.5 -4.4, 3.8 -1.1, 1.3
4 53.8, 61.0 1.3, -1.8 -1.4, 1.5
5 73.1, 79.4 -1.6, 1.0 -1.4, 1.5
6 73.1, 79.4 -1.6, 1.0 -1.4, 1.5
7 73.1, 79.4 -1.6, 1.0 -1.4, 1.5

8 73.1, 79.4 -1.6, 1.0 -1.4, 1.5

Critical Loading: 1 - (G*F)

min Design
N 95.7 - 95.7 kN
M11 -2.0 -1.1 -2.0 kN.m
M22 1.8 1.1 1.8 kN.m
Nmax 830.6
Concrete Cover = 40.0 mm
Neutral Axis: 67.7 mm / 9.10 O

Vd(1/2) = 0.7 / 2.0 kN Short Column... As (Req): %0.40 (min) 211.60 mm2
vc'(1/2) = 0.83 / 0.85 N/mm2 Le1/b1 = 11.4 < 15.0 √ As (Sup): %1.52 804.25 mm2
v(1/2) = 0.01 / 0.04 N/mm2 Le2/b2 = 11.5 < 15.0 √
Madd(1/2) = 0.0 / 0.0 kN.m 4H16
Links = H8-175

ProtaStructure v3.0.4 Page 26

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B1
FC8, FC9, FC12, FC7, FC13, FC14 (300.0 / 300.0
Columns:
mm)

Critical Loading: (FC14 1: G*F) N = -1571.8 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 3200.0 x 3200.0 mm

h = 600 mm

Soil Stresses: σmax = 203.707 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 203.707 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 214.1 kN.m/m K/K' = 0.19≤1.0 √
As(Req) = 1200.00 mm2/m As(Sup) = 1340.41 mm2/m H16-150
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.54 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.34 N/mm2≤ vc = 0.37 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 2067.6 kN V-eff = 2067.6 kN
v = 3.23 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 1349.0 kN V-eff = 1349.0 kN
v = 0.33 N/mm2≤ vc = 0.37 N/mm2 √
Y Dir: Bending: M = 214.1 kN.m/m K/K' = 0.20≤1.0 √
As(Req) = 1200.00 mm2/m As(Sup) = 1340.41 mm2/m H16-150
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.56 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.36 N/mm2≤ vc = 0.37 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 2067.6 kN V-eff = 2067.6 kN
v = 3.23 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 1349.0 kN V-eff = 1349.0 kN
v = 0.33 N/mm2≤ vc = 0.37 N/mm2 √

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B2
FC1, FC2, FC3, FC4, FC5, FC6, FC10, FC15, FC21,
Columns:
FC20, FC11 (300.0 / 300.0 mm)

Critical Loading: (FC4 1: G*F) N = -888.8 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 2500.0 x 2500.0 mm

h = 450 mm

Soil Stresses: σmax = 197.518 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 197.518 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 119.5 kN.m/m K/K' = 0.20≤1.0 √
As(Req) = 900.00 mm2/m As(Sup) = 1005.31 mm2/m H16-200
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.55 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.36 N/mm2≤ vc = 0.40 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 1216.7 kN V-eff = 1216.7 kN
v = 2.64 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 818.1 kN V-eff = 818.1 kN
v = 0.37 N/mm2≤ vc = 0.40 N/mm2 √
Y Dir: Bending: M = 119.5 kN.m/m K/K' = 0.22≤1.0 √
As(Req) = 900.00 mm2/m As(Sup) = 1005.31 mm2/m H16-200
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.58 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.38 N/mm2≤ vc = 0.41 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 1216.7 kN V-eff = 1216.7 kN
v = 2.64 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 818.1 kN V-eff = 818.1 kN
v = 0.37 N/mm2≤ vc = 0.41 N/mm2 √

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B4
FC34, FC35, FC36, FC37, FC38, FC39, FC40, FC41,
Columns:
FC42, FC46, FC50, FC54, FC58, FC62 (230.0 / 230.0 mm)

Critical Loading: (FC40 1: G*F) N = -273.4 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 1300.0 x 1300.0 mm

h = 300 mm

Soil Stresses: σmax = 207.977 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 207.977 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 29.8 kN.m/m K/K' = 0.13≤1.0 √
As(Req) = 600.00 mm2/m As(Sup) = 646.27 mm2/m H12-175
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.46 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.25 N/mm2≤ vc = 0.46 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 340.5 kN V-eff = 340.5 kN
v = 1.55 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 166.1 kN V-eff = 166.1 kN
v = 0.18 N/mm2≤ vc = 0.46 N/mm2 √
Y Dir: Bending: M = 29.8 kN.m/m K/K' = 0.14≤1.0 √
As(Req) = 600.00 mm2/m As(Sup) = 646.27 mm2/m H12-175
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.48 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.27 N/mm2≤ vc = 0.47 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 340.5 kN V-eff = 340.5 kN
v = 1.55 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 166.1 kN V-eff = 166.1 kN
v = 0.18 N/mm2≤ vc = 0.47 N/mm2 √

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B5
Columns: FC16, FC17, FC18 (300.0 / 300.0 mm)

Critical Loading: (FC17 1: G*F) N = -791.6 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 2300.0 x 2300.0 mm

h = 450 mm

Soil Stresses: σmax = 204.866 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 204.866 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 102.4 kN.m/m K/K' = 0.17≤1.0 √
As(Req) = 900.00 mm2/m As(Sup) = 1005.31 mm2/m H16-200
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.52 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.32 N/mm2≤ vc = 0.40 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 1065.3 kN V-eff = 1065.3 kN
v = 2.31 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 651.8 kN V-eff = 651.8 kN
v = 0.29 N/mm2≤ vc = 0.40 N/mm2 √
Y Dir: Bending: M = 102.4 kN.m/m K/K' = 0.19≤1.0 √
As(Req) = 900.00 mm2/m As(Sup) = 1005.31 mm2/m H16-200
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.54 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.34 N/mm2≤ vc = 0.41 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 1065.3 kN V-eff = 1065.3 kN
v = 2.31 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 651.8 kN V-eff = 651.8 kN
v = 0.29 N/mm2≤ vc = 0.41 N/mm2 √

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Buiilding 150mm Slab Rev B Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B6
FC12, FC23, FC24, FC25, FC26, FC27, FC28, FC29,
Columns: FC30, FC19, FC20, FC31, FC43, FC47, FC51, FC55,
FC59, FC63, FC64 (230.0 / 230.0 mm)

Critical Loading: (FC24 1: G*F) N = -567.1 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 1900.0 x 1900.0 mm

h = 400 mm

Soil Stresses: σmax = 209.412 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 209.412 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 73.0 kN.m/m K/K' = 0.16≤1.0 √
As(Req) = 800.00 mm2/m As(Sup) = 804.25 mm2/m H16-250
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.51 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.30 N/mm2≤ vc = 0.41 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 744.9 kN V-eff = 744.9 kN
v = 2.42 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 438.1 kN V-eff = 438.1 kN
v = 0.27 N/mm2≤ vc = 0.41 N/mm2 √
Y Dir: Bending: M = 73.0 kN.m/m K/K' = 0.18≤1.0 √
As(Req) = 800.00 mm2/m As(Sup) = 804.25 mm2/m H16-250
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.54 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.33 N/mm2≤ vc = 0.42 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 744.9 kN V-eff = 744.9 kN
v = 2.42 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 438.1 kN V-eff = 438.1 kN
v = 0.27 N/mm2≤ vc = 0.42 N/mm2 √

ProtaStructure v3.0.4 Page 1

 JNHPP Administration Building Ent Hall Mhandisi Consultancy
Pad Footing Design Calc. By: G L
Rev: 1 Checked By: H J

Pad Footing Design

B7
Columns: FC22 (230.0 / 230.0 mm)

Critical Loading: (3: G+Q *F1) N = -235.9 kN

Mx x My = 0.0 x 0.0 kN.m

Footing Dimensions: Lx x Ly = 1400.0 x 1400.0 mm

h = 400 mm

Soil Stresses: σmax = 191.518 ≤ 210 kN/m2 (1.4x150 kN/m2) √

σmin = 191.518 ≥ 0 kN/m2 √

Design:
X Dir: Bending: M = 32.8 kN.m/m K/K' = 0.07≤1.0 √
As(Req) = 800.00 mm2/m As(Sup) = 804.25 mm2/m H16-250
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.33 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.14 N/mm2≤ vc = 0.41 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 365.2 kN V-eff = 365.2 kN
v = 1.19 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 84.7 kN V-eff = 84.7 kN
v = 0.05 N/mm2≤ vc = 0.41 N/mm2 √
Y Dir: Bending: M = 32.8 kN.m/m K/K' = 0.08≤1.0 √
As(Req) = 800.00 mm2/m As(Sup) = 804.25 mm2/m H16-250
Shear Check: (BS8110-Cl.3.4.5.2)
(At Column Face) v = 0.34 N/mm2≤ v-max = 4.00 N/mm2 √
(At 'd' from Column) v = 0.15 N/mm2≤ vc = 0.42 N/mm2 √
Punching (BS8110-Cl.3.7.6.4)
(At Column Face) Vt = 365.2 kN V-eff = 365.2 kN
v = 1.19 N/mm2≤ v-max = 4.00 N/mm2 √
(At '1.5d' from Column) Vt = 84.7 kN V-eff = 84.7 kN
v = 0.05 N/mm2≤ vc = 0.42 N/mm2 √

ProtaStructure v3.0.4 Page 1

 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 1
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

LIFT SHAFT COLUMNS BASE

Foundation analysis in accordance with EN1997-1:2004 incorporating Corrigendum dated February 2009 and the UK
National Annex incorporating Corrigendum No.1
Tedds calculation version 3.2.21

Pad foundation details

Length of foundation; Lx = 3500 mm; Width of foundation; Ly = 3500 mm
Depth of foundation; h = 350 mm; Depth of soil over foundation; hsoil = 2650 mm
Level of water; hwater = 0 mm; Density of water; water = 9.8 kN/m3
Density of concrete; conc = 25.0 kN/m3

Column no.1 details

Length of column; lx1 = 230 mm; Width of column; ly1 = 230 mm
position in x-axis; x1 = 615 mm; position in y-axis; y1 = 615 mm
Column no.2 details
Length of column; lx2 = 230 mm; Width of column; ly2 = 230 mm
position in x-axis; x2 = 2885 mm; position in y-axis; y2 = 615 mm
Column no.3 details
Length of column; lx3 = 230 mm; Width of column; ly3 = 230 mm
position in x-axis; x3 = 615 mm; position in y-axis; y3 = 2885 mm
Column no.4 details
Length of column; lx4 = 230 mm; Width of column; ly4 = 230 mm
position in x-axis; x4 = 2885 mm; position in y-axis; y4 = 2885 mm
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 2
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Soil properties
Density of soil; soil = 18.0 kN/m3; Net ultimate bearing pressure; nf = 150 kN/m2
Friction angle; k = 19.3 deg

Foundation loads
Permanent surcharge load; FGsur = 5.0 kN/m2; Variable surcharge load; FQsur = 5.0 kN/m2
2
Self weight; Fswt = 8.8 kN/m ; Soil weight; Fsoil = 47.7 kN/m2
Column no.1 loads
Permanent load in z; FGz1 = 144.0 kN; Variable load in z; FQz1 = 32.0 kN
Column no.2 loads
Permanent load in z; FGz2 = 158.0 kN; Variable load in z; FQz2 = 34.0 kN
Column no.3 loads
Permanent load in z; FGz3 = 135.0 kN; Variable load in z; FQz3 = 32.0 kN
Column no.4 loads
Permanent load in z; FGz4 = 174.0 kN; Variable load in z; FQz4 = 49.0 kN
Bearing resistance (Section 6.5.2)
Forces on foundation
Force in z-axis; Fdz = 1572.0 kN
Moments on foundation
Moment in x-axis; Mdx = 2832.7 kNm; Moment in y-axis; Mdy = 2776.0 kNm
Eccentricity of base reaction
Eccentricity in x-axis; ex = 52 mm; Eccentricity in y-axis; ey = 16 mm
Eccentricity of base reaction
Eccentricity in x-axis; ex = 52 mm; Eccentricity in y-axis; ey = 16 mm
Pad base pressure
q1 = 113.4 kN/m2; q2= 120.4 kN/m2; q3 = 136.3 kN/m2; q4 = 143.3 kN/m2
Minimum base pressure; qmin = 113.4 kN/m2; Maximum base pressure; qmax = 143.3 kN/m2
Presumed bearing capacity
Presumed bearing capacity; Pbearing = 150.0 kN/m2
PASS - Presumed bearing capacity exceeds design base pressure
Design approach 1
Partial factors on actions - Combination1
Partial factor set; A1
Permanent action; G = 1.35; Variable action; Q = 1.50
Partial factors for spread foundations - Combination1
Resistance factor set; R1
Bearing; R.v = 1.00; Sliding; R.h = 1.00
Forces on foundation
Force in z-axis; Fdz = 2153.5 kN
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 3
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Moments on foundation
Moment in x-axis; Mdx = 3882.1 kNm; Moment in y-axis; Mdy = 3804.8 kNm
Eccentricity of base reaction
Eccentricity in x-axis; ex = 53 mm; Eccentricity in y-axis; ey = 17 mm
Effective area of base
Effective length; L'x = 3395 mm; Effective width; L'y = 3466 mm
2
Effective area; A' = 11.767 m
Pad base pressure
Design base pressure; fdz = 183.0 kN/m2
Design approach 1
Partial factors on actions - Combination2
Partial factor set; A2
Permanent action; G = 1.00; Variable action; Q = 1.30
Partial factors for spread foundations - Combination2
Resistance factor set; R1
Bearing; R.v = 1.00; Sliding; R.h = 1.00
Forces on foundation
Force in z-axis; Fdz = 1634.5 kN
Moments on foundation
Moment in x-axis; Mdx = 2948.5 kNm; Moment in y-axis; Mdy = 2890.4 kNm
Eccentricity of base reaction
Eccentricity in x-axis; ex = 54 mm; Eccentricity in y-axis; ey = 18 mm
Effective area of base
Effective length; L'x = 3392 mm; Effective width; L'y = 3463 mm
Effective area; A' = 11.747 m2
Pad base pressure
Design base pressure; fdz = 139.1 kN/m2

LIFT SHAFT COLUMNS BASE

Foundation design in accordance with EN1992-1-1:2004 incorporating Corrigendum dated January 2008 and the UK
National Annex incorporating National Amendment No.1
Tedds calculation version 3.2.21

Concrete details (Table 3.1 - Strength and deformation characteristics for concrete)
Concrete strength class; C20/25 Char.comp.cylinder strength; fck = 20 N/mm2
Partial factor for concrete; C = 1.50; Maximum aggregate size; hagg = 20 mm
2
Design compressive strength; fcd = 17.0 N/mm ; Design tensile strength, plain; fctd,pl = 1.1 N/mm2
Reinforcement details
Characteristic yield strength; fyk = 500 N/mm2; Partial factor for reinforcment; S = 1.15
2
Design yield strength; fyd = 435 N/mm ; Nominal cover; cnom = 50 mm
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 4
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Shear diagram, x axis (kN)

Moment diagram, x axis (kNm)

Rectangular section in flexure (Section 6.1)

Design bending moment; MEd.x.max = 43.6 kNm; K = 0.007; K' = 0.207
K' > K - No compression reinforcement is required
Tens.reinforcement required; Asx.bot.req = 1338 mm2
Tens.reinforcement provided; 18 No.12 dia.bars bottom (200 c/c); Asx.bot.prov = 2036 mm2
Min.area of reinforcement; As.min = 1338 mm2; Max.area of reinforcement; As.max = 41160 mm2
PASS - Area of reinforcement provided is greater than area of reinforcement required
Crack control (Section 7.3)
Limiting crack width; wmax = 0.3 mm; Maximum crack width; wk = 0.073 mm
PASS - Maximum crack width is less than limiting crack width
Rectangular section in flexure (Section 6.1)
Design bending moment; abs(MEd.x.min) = 135.9 kNm; K = 0.024; K' = 0.207
K' > K - No compression reinforcement is required
Tens.reinforcement required; Asx.top.req = 1283 mm2
Tens.reinforcement provided; 18 No.12 dia.bars top (200 c/c); Asx.top.prov = 2036 mm2
Min.area of reinforcement; As.min = 1283 mm2; Max.area of reinforcement; As.max = 39480 mm2
PASS - Area of reinforcement provided is greater than area of reinforcement required
Crack control (Section 7.3)
Limiting crack width; wmax = 0.3 mm; Maximum crack width; wk = 0.258 mm
PASS - Maximum crack width is less than limiting crack width
Rectangular section in shear (Section 6.2)
Design shear force; VEd.x.max = 230.4 kN; Design shear resistance; VRd.c = 386.3 kN
PASS - Design shear resistance exceeds design shear force
Shear diagram, y axis (kN)
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 5
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Moment diagram, y axis (kNm)

Rectangular section in flexure (Section 6.1)

Design bending moment; MEd.y.max = 39.3 kNm; K = 0.007; K' = 0.207
K' > K - No compression reinforcement is required
Tens.reinforcement required; Asy.bot.req = 1283 mm2
Tens.reinforcement provided; 18 No.12 dia.bars bottom (200 c/c); Asy.bot.prov = 2036 mm2
2
Min.area of reinforcement; As.min = 1283 mm ; Max.area of reinforcement; As.max = 39480 mm2
PASS - Area of reinforcement provided is greater than area of reinforcement required
Crack control (Section 7.3)
Limiting crack width; wmax = 0.3 mm; Maximum crack width; wk = 0.073 mm
PASS - Maximum crack width is less than limiting crack width
Rectangular section in flexure (Section 6.1)
Design bending moment; abs(MEd.y.min) = 135.9 kNm; K = 0.022; K' = 0.207
K' > K - No compression reinforcement is required
Tens.reinforcement required; Asy.top.req = 1338 mm2
Tens.reinforcement provided; 18 No.12 dia.bars top (200 c/c); Asy.top.prov = 2036 mm2
Min.area of reinforcement; As.min = 1338 mm2; Max.area of reinforcement; As.max = 41160 mm2
PASS - Area of reinforcement provided is greater than area of reinforcement required
Crack control (Section 7.3)
Limiting crack width; wmax = 0.3 mm; Maximum crack width; wk = 0.229 mm
PASS - Maximum crack width is less than limiting crack width
Rectangular section in shear (Section 6.2)
Design shear force; VEd.y.max = 223.6 kN; Design shear resistance; VRd.c = 386.3 kN
PASS - Design shear resistance exceeds design shear force
Punching shear (Section 6.4)
Maximum shear resiastance; vRd.max = 4.692 N/mm2; Punching shear resistance; vRd.c = 0.391 N/mm2
Column No.1 - Punching shear perimeter at column face
Punching shear perimeter; u0 = 920 mm; Area within shear perimeter; A0 = 0.053 m2
Max.punching shear force; VEd.max = 237.5 kN
Punching shear stress factor;  = 1.500; Max.punching shear stress; vEd.max = 1.345 N/mm2
PASS - Maximum punching shear resistance exceeds maximum punching shear stress
Column No.1 - Punching shear perimeter at 1d from column face
Punching shear perimeter; u1 = 2730 mm; Area within shear perimeter; A1 = 0.578 m2
Design punching shear force; VEd.1 = 188.9 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.1 = 0.360 N/mm2
PASS - Design punching shear resistance exceeds increased design punching shear stress
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 6
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Column No.1 - Punching shear perimeter at 2d from column face

Punching shear perimeter; u2 = 2882 mm; Area within shear perimeter; A2 = 1.531 m2
Design punching shear force; VEd.2 = 124.3 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.2 = 0.225 N/mm2
PASS - Design punching shear resistance exceeds design punching shear stress
Column No.2 - Punching shear perimeter at column face
Punching shear perimeter; u0 = 920 mm; Area within shear perimeter; A0 = 0.053 m2
Max.punching shear force; VEd.max = 259.4 kN
Punching shear stress factor;  = 1.500; Max.punching shear stress; vEd.max = 1.469 N/mm2
PASS - Maximum punching shear resistance exceeds maximum punching shear stress
Column No.2 - Punching shear perimeter at 1d from column face
Punching shear perimeter; u1 = 2730 mm; Area within shear perimeter; A1 = 0.578 m2
Design punching shear force; VEd.1 = 210.8 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.1 = 0.402 N/mm2
PASS - Design punching shear resistance exceeds increased design punching shear stress
Column No.2 - Punching shear perimeter at 2d from column face
Punching shear perimeter; u2 = 2882 mm; Area within shear perimeter; A2 = 1.531 m2
Design punching shear force; VEd.2 = 127.8 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.2 = 0.231 N/mm2
PASS - Design punching shear resistance exceeds design punching shear stress
Column No.3 - Punching shear perimeter at column face
Punching shear perimeter; u0 = 920 mm; Area within shear perimeter; A0 = 0.053 m2
Max.punching shear force; VEd.max = 225.4 kN
Punching shear stress factor;  = 1.500; Max.punching shear stress; vEd.max = 1.276 N/mm2
PASS - Maximum punching shear resistance exceeds maximum punching shear stress
Column No.3 - Punching shear perimeter at 1d from column face
Punching shear perimeter; u1 = 2730 mm; Area within shear perimeter; A1 = 0.578 m2
Design punching shear force; VEd.1 = 176.7 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.1 = 0.337 N/mm2
PASS - Design punching shear resistance exceeds increased design punching shear stress
Column No.3 - Punching shear perimeter at 2d from column face
Punching shear perimeter; u2 = 2882 mm; Area within shear perimeter; A2 = 1.531 m2
Design punching shear force; VEd.2 = 106.8 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.2 = 0.193 N/mm2
PASS - Design punching shear resistance exceeds design punching shear stress
Column No.4 - Punching shear perimeter at column face
Punching shear perimeter; u0 = 920 mm; Area within shear perimeter; A0 = 0.053 m2
Max.punching shear force; VEd.max = 303.5 kN
Punching shear stress factor;  = 1.500; Max.punching shear stress; vEd.max = 1.718 N/mm2
PASS - Maximum punching shear resistance exceeds maximum punching shear stress
Column No.4 - Punching shear perimeter at 1d from column face
Punching shear perimeter; u1 = 2730 mm; Area within shear perimeter; A1 = 0.578 m2
 Project Job Ref.

Julius Nyerere Hydropower Project - JNHPP

Section Sheet no./rev.
Mhandisi Consultancy Limited
Plot No. 305B,
Administration Building Lift Shaft Bases 7
Rweyabura Street, Mikocheni Calc. by Date Chk'd by Date App'd by Date

P O Box 12965, Dar Es Salaam, Tanzania. GL 3/3/2021 Josia, H 3/3/2021 3/3/2021

Design punching shear force; VEd.1 = 254.9 kN

Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.1 = 0.486 N/mm2
PASS - Design punching shear resistance exceeds increased design punching shear stress
Column No.4 - Punching shear perimeter at 2d from column face
Punching shear perimeter; u2 = 2882 mm; Area within shear perimeter; A2 = 1.531 m2
Design punching shear force; VEd.2 = 166.7 kN
Punching shear stress factor;  = 1.500; Design punching shear stress; vEd.2 = 0.301 N/mm2
PASS - Design punching shear resistance exceeds design punching shear stress