Date: 10/28/2024

Configuration Number: C-2024-957706

Product Configuration Technical Specification Sheet

Basic Product Information
Model Number CHH-6185-17
Cyclo® Frame Size 6185
Housing Style (H) Foot Mount
Shaft Orientation (H) Horizontal
Output Shaft Specification ( ) Standard Metric Size
Input Configuration ( ) Free Input Shaft
Input Shaft Specification Metric Shaft

Application Information
Ratio 17
Input / Output RPM 1750 / 103

NOTE: Information displayed on this technical specification sheet will vary,

as it is based upon your actual selections. Please see next page for more
configuration specific information.

Dimensions shown are for reference only and are subject to change without
notice, unless certified. Certified prints are available after receipt of an
order; consult factory for more information. Image shown is representative
and may not reflect actual unit and/or orientation.

Units: mm Approximate Weight: 163 kg

A B C D E E1 F F1 G H J O1 O P P1 BW
Casing
470 380 527 220 210 25 320 30 30 22 85 - 467 370 390 145

U U TOL. V S L1 KEY
Output Shaft
80.00 +0 / -0.019 110 M12 24 22 x 14 x 100

XU XU TOL. XV KEY
Input Shaft
40.00 +0 / -0.016 65 12 x 8 x 63

For worldwide locations, visit sumitomodrive.com/worldwide

©2024 Sumitomo Machinery Corporation of America
All rights reserved
Page 1 of 2
 Date: 10/28/2024
Configuration Number: C-2024-957706

Product Configuration Technical Specification Sheet

Input Configuration Product Ratings
Input Stage Frame Size 618 Application or Motor Input Power - kW
High Speed End Shield Pilot Included Service Factor -
Motor Mounting Not Applicable Calculated Output Torque - N-m
Motor Coupling Guard Not Applicable Rated Input RPM 1750
Input Shaft Accessory Mounting Not Selected Rated Output RPM 103
Product Rated Input Power 39 kW
Lubrication Specifications Product Rated Output Torque 3440 N-m
Lubrication Requirement Standard Lubrication Product Overhung Load Capacity 20500 N
Lubrication Method Oil Bath
Lubrication Option NO OIL (customer to fill) Reducer Options
Mill Duty Option Not Selected
Environmental Specifications Chemical Duty Option Not Selected
Installation Location Indoor Dusty, Weather Proof IP54 Option Not Selected
Ambient Temperature 14° - 104°F (-10° - 40°C ) Food & Washdown Options None Selected
Ambient Humidity Under 90% Ductile Iron Housing Option Not Selected
Environment Standard High Capacity Bearing Option Not Selected
Food Grade Required No Shoulder Bolts / Dowel Pins Option Not Selected
Elevation Above Sea Level Under 3300 ft/1000 m Eccentric Backlash Reduction Not Selected
Severe Duty Breather Not Selected
Glass Sight Oil Gauge Option Not Selected
Magnetic Drain Plug Not Selected
Drain Valve Not Selected
Drain Type Standard Drain Plug
Seal Options Nitrile Seal
Double Output Oil Seals Option Not Selected
Paint Specification Standard Paint

Configuration Messages
Output Shaft Overhung Load (OHL) Capacity
The Output Shaft OHL Capacity needs to be checked if Output Shaft is not direct coupled to the application. Using the Product Overhung Load
Capacity value from the Selection, please check it against the actual OHL using the method described in the Catalog. If Cyclo unit will see
significant vibration from the application and the Cyclo output shaft will not be direct coupled to the application, please consult the Factory for
additional guidelines on Service Factor adjustment.

All Configuration data contained within this technical specification sheet is subject to change. Please refer to Sumitomo Drive Technologies' Terms and
Conditions located at smcyclo.com for further information. For more specific product and/or application data, please contact your Sumitomo Drive
Technologies' Representative.

To request a catalog, or for more information, on any of our high quality products, please visit our website: www.sumitomodrive.com.

Thank you for your interest in Sumitomo products.

For worldwide locations, visit sumitomodrive.com/worldwide

©2024 Sumitomo Machinery Corporation of America
All rights reserved
Page 2 of 2