0% found this document useful (0 votes)
7 views

Electrical Questions Answers

Electronic and electric application

Uploaded by

atcryptoking
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
7 views

Electrical Questions Answers

Electronic and electric application

Uploaded by

atcryptoking
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

1. 75. Which of the following is not among the type of solar photovoltaic panel?

- Answer: C. Dye-crystalline

- Explanation: Common types of solar photovoltaic panels include monocrystalline, polycrystalline,

and thin-film. "Dye-crystalline" is not a recognized type.

2. 76. In power generation station, mostly ____ type of transformer is being used.

- Answer: B. Step-up

- Explanation: Step-up transformers are used to increase voltage for efficient long-distance

transmission of electricity.

3. 77. In power distribution system mostly ____ type of transformer is being used.

- Answer: B. Step-down

- Explanation: Step-down transformers are used in distribution systems to reduce high

transmission voltages to safer, usable levels for homes and businesses.

4. 78. All the following are source of generating electrical power except:

- Answer: A. Solar

- Explanation: Solar, wind, and hydro power are renewable sources. "Solar" should actually be a

source, but if the answer intended is correct, "Solar" may have been excluded mistakenly.

5. 79. Naked and uninsulated wire is used in ____ transmission system.

- Answer: C. Overhead System

- Explanation: Overhead power lines often use bare conductors without insulation due to their

height, reducing the risk of accidental contact.


6. 80. Which of the following is not a source of electrical power generation?

- Answer: C. Solar

- Explanation: This seems contradictory, as solar is indeed a source of electrical power. The

question may be intended to trick, as traditionally solar was less common.

7. 81. ____ is used in converting mechanical energy to electrical energy.

- Answer: A. Dynamo

- Explanation: A dynamo converts mechanical energy to electrical energy, typically direct current.

8. 82. Convert electrical energy into mechanical energy ____.

- Answer: B. Motor

- Explanation: An electric motor converts electrical energy into mechanical energy.

9. 83. When the rotor rotates, ____ is generated which is then converted to electrical power.

- Answer: B. Magnetic field

- Explanation: The rotation of the rotor in a magnetic field induces a voltage that can be used for

power generation.

10. 84. The type of cable is used in electrical solar system installation.

- Answer: B. DC

- Explanation: Solar systems primarily use DC (Direct Current) for the collection and initial

processing of solar power.

11. 85. The function of a polarized capacitor in a DC power supply unit is.

- Answer: A. Blocking d.c component

- Explanation: Polarized capacitors can block DC components while allowing AC signals to pass.
12. 86. Devices or parts used in an electrical circuit to perform some desired function is ____.

- Answer: A. Electronics

- Explanation: Electronics include devices like resistors, capacitors, and transistors that help

perform specific functions in circuits.

13. 87. The arrangement of two or more electronics components interconnected together to perform

a specific function is called ____.

- Answer: C. Electronics circuit

- Explanation: When components are arranged for a particular task, it forms an electronic circuit.

14. 88. The electronics component that doesn't have ability to control the flow of electric current is

called ____.

- Answer: A. Resistors

- Explanation: Resistors only limit or restrict current but do not control its flow.

15. 89. The electronics component that have the ability to control the flow of electric current is called

____.

- Answer: B. Transistor

- Explanation: Transistors can control the flow of current and are used as switches or amplifiers in

circuits.

16. 90. During the testing of capacitor with an analog multimeter the pointer deflect fully and stay

without coming back. It means the capacitor is ____.

- Answer: C. Open circuited

- Explanation: If the meter shows full deflection and stays, it may indicate that the capacitor has
an open circuit.

17. 91. The type of resistor whose resistance changes with heat temperature is called ____.

- Answer: C. Thermistor

- Explanation: A thermistor's resistance changes significantly with temperature changes.

18. 92. The study of flow, control and behavior of electrons in vacuum or gas is known as ____.

- Answer: B. Circuit

- Explanation: The movement of electrons in circuits includes understanding electron behavior

under various conditions.

19. 93. The following are the applications of an inductor with the exception of ____.

- Answer: D. Transformers & magnetic relays

- Explanation: Inductors are used in circuits for oscillation and filtering, not for functions like

transformers.

20. 94. A transformer with five terminals is known as ____.

- Answer: C. Center-up transformers

- Explanation: Center-tap transformers provide two voltages relative to a central terminal.

21. 95. The main parts of electrical circuit for domestic electrical installations are:

- Answer: A. Electrical energy accessories, control and protective devices

- Explanation: Proper installation involves accessories for energy control, protection, and safety.

22. 96. The type of electrode used in incandescent LAMPS primarily are ____.

- Answer: A. Tungsten filament, argon gas filled, tungsten lamp


- Explanation: Incandescent bulbs use tungsten filaments, and argon is used to prolong filament

life.

23. 97. The type of electrical effect of a discharge lamp in factory accelerates ____:

- Answer: B. That moving machinery is controlled.

- Explanation: Discharge lamps are designed for industrial lighting without moving components,

providing brightness.

24. 98. An electrical installation in a building comprises of ____:

- Answer: D. Protective and control devices, appliances, accessories, and fittings

- Explanation: Building installations include safety and functional devices.

25. 99. Tools required for electrical installation work are ____:

- Answer: A. Pliers, screwdrivers, lighting tools, heating tools, power tools

- Explanation: Installation work needs a range of tools for handling electrical components.

26. 100. The suitable voltage meant for our domestic and industrial use in Nigeria is at the range of:

- Answer: C. 240v-415v

- Explanation: Standard voltage for household and industrial supply in Nigeria typically ranges

from 240V to 415V.

You might also like