IMPORTANT: ONCE inLab CAM 22 IS INSTALLED, ALL PREVIOUS DATA WILL

BE CONVERTED FOR inLab CAM 22 AND WILL NO LONGER BE ABLE TO BE
ACCESSED FROM OLDER VERSIONS OF inLab SOFTWARE.

***DEPENDING ON THE SIZE OF THE CAMDATA, THE CONVERSION MAY TAKE

MINUTES OR HOURS. BE PREPARED FOR THE DATA TO BE INACCESSIBLE
DURING THIS TIME***

IF THE DATA NEEDS TO BE ACCESSED BY OLDER VERSIONS, YOU WILL HAVE

TO MAKE A BACKUP OF CAMDATA BEFORE THE inLab CAM 22 INSTALLATION.

ONCE inLab 22 IS INSTALLED AND UPDATED, IT IS STRONGLY RECOMMENDED

TO UNINSTALL OLDER VERSIONS OF inLab CAM. DO NOT ROLL BACK TO
PREVIOUS inLab CAM SOFTWARE VERSIONS OR FIRMWARES ON
DENTSPLY SIRONA EQUIPMENT. THIS IS TO PREVENT POSSIBLE FIRMWARE
CORRUPTION.
Table of Contents
Download and Extract Software ............................................................................................................ 2
inLab CAD SW 22 .................................................................................................................................... 3
inLab CAM SW 22 .................................................................................................................................... 8
inLab Applications ................................................................................................................................ 16
inLab Model ...................................................................................................................................................... 16
inLab Partial Framework .................................................................................................................................19
inLab Splint....................................................................................................................................................... 22
License Key Entry and Activation ....................................................................................................... 25


 New to inLab CAM 22 is CAM Services. This manages all of CAM Data
Only one instance of CAM Service is running per network. This could be on a
server or any PC on the network that has access to all PC’s running inLab 22.

The initial conversion of data can take anywhere from a few minutes to hours
depending on the amount of data in the CAM Data folder.

Once all the Data has been converted it will no longer be accessible from older
inLab versions of SW.

The CAM Service will monitor the CAM Data folder and remove anything within
it and place it in CAM Services folder.

Once inLab CAM 22 is installed and updated, it is advised that older versions
of inLab CAM should be uninstalled. Do not roll back to previous software or
firmware on DS equipment.

                         
                                              
       
    
                                             
                     
                          
                  ­€    ‚ ƒ       
 „              „   €   † † ‡ ‡               „   €   † † ‡ ‡       ˆ     ‰        
 „              „   € Š  † † ‡ ‡               „   € Š  † † ‡ ‡       ˆ     ‰        
 „              „  Š    † † ‡ ‡ 
 „              „      † † ‡ ‡ 
 „              „  ˆ     ‹         † † ‡ ‡ 

† Œ                         ­           Ž                         

 ‘ ’                  
     
     Ž            
‘ ’      €  
“ Š                       ’                     ”                ’              
          ’               ‘ ’      
• Œ            ­             
              
– —                      Ž     Œ                  ’        ­           
 
                  

                        
˜         
       ™ š š • › œ › – š š ­Œ     ›
  ˆ              
      ‰ˆ    ™ š š • ž – – š “ œ 


inLab CAD SW 22
1) Run windows updates and verify that your system is up-to-date.
2) Open the inLab CAD SW 22 folder and double-click the setup file (Figure 1) to start the
installation process (or right click and select ‘run’).

Figure 1

3) If prompted by your computer, “Do you want to allow this app to make changes to your
device?” select ‘Yes’.
4) The software splash screen should open and begin verifying the files that were downloaded
(Figure 2).

Figure 2


5) Once the files have been verified, the software installation window will open. Select the
appropriate language (Figure 3) and click ‘next’ twice.

Figure 3

6) You should now be on the Application Configuration screen (Figure 4). Select the appropriate
folders in which you would like the application. Most customers can leave the default settings.
Select “Next” when you are ready to advance.

Figure 4

7) The software will begin installing (Figure 5). Please wait up to 10 minutes.

Figure 5

8) Once the software has been installed, you will reach the ‘Data Collection Agreement’ (Figure
6). Read the screen and when you are ready to continue with the setup, select ‘Next.’

Figure 6


 9) The installation is now complete (Figure 7). To open the software/application, select ‘START.’

Figure 7

10) Once the software opens, you will be 11) Read the Software License Agreement.
prompted to setup the software (Figure 8). If you accept the terms, click in the empty box
Select your language and region. Click “Next”. to accept the terms (Figure 9). Click “Next”.

Figure 8 Figure 9


12) Next step is to set the filepath for your data 13) Read the agreement to participate in anonymous
(Figure 10). Most customers can use the usage logs to help improve the software (Figure 11).
default settings. Once this is set, click “Next”. If you agree, check the box. If you do not agree,
leave the box unchecked. Once you have decided,
click “Start inLab CAD”.

Figure 10 Figure 11

14) inLab CAD 22 is now setup. You will need to enter your license key to exit demo mode.
Complete the install of CAM 22 and ALL Applications first (if you have more to install), and
then follow the ‘License Key Entry and Activation’ instructions.

REVIEW IMPORTANT NOTES ON PAGE 1 IF NOT ALREADY DONE.


inLab CAM SW 22
REVIEW IMPORTANT NOTES ON PAGE 1 IF NOT ALREADY DONE.
1) Run windows updates and verify that your system is up-to-date.
2) Open the inLab CAD SW 22 folder and double-click the setup file (Figure 1) to start the
installation process (or right click and select ‘run’).

Figure 1
3) If prompted by your computer, “Do you want to allow this app to make changes to your
device?” select ‘Yes’.
4) The inLab CAM SW Installation Wizard will start. It will scan the current network for any other
instances of CAM Service. If none are available, it will prompt to install CAM Service (Figure 2).
CAM Service is required for inLab 22. NOTE: CAM SERVICE WILL CONVERT ALL DATA
TO CAM SERVICE AND WILL NO LONGER BE ACCESSIBLE FROM OLDER VERSIONS
OF inLab SOFTWARE (<inLab 22). Only 1 instance of CAM Service should be installed on a
network with inLab equipment or software. If a known CAM Service is already being used on the
network, select it once the install wizard discovers it during the scan and proceed to step 7.

Figure 2


5) You should now be on the CAM Service Welcome to setup screen (Figure 3). Select the
appropriate region and click “Next”.

Figure 3
6) Read the agreement to participate in anonymous usage logs to help improve the software
(Figure 4). If you agree, check the box. If you do not agree, leave the box unchecked.
Once you have decided, click “Next”.

Figure 4


7) The software will begin installing (Figure 5). Please wait up to 10 minutes.
Once completed, click “Quit”.

Figure 5

7) Software will scan for CAM Service again and should find the 8) The software will begin installing
newly installed CAM Service Instance (Figure 6). (Figure 7). Please wait up to
After this is completed, check the box to install DS Monitor and 10 minutes.
click “Install”.

Figure 6 Figure 7


9) Once DS Monitor is finished, the inLab CAM 22 splash screen should open and begin verifying
the files that were downloaded (Figure 8).

Figure 8

10) Once the files have been verified, the software installation window will open. Select the
appropriate language (Figure 9) and click ‘next’ twice.

Figure 9


 11) You should now be on the Application Configuration screen (Figure 10). Select the appropriate
folders in which you would like the application. Most customers can leave the default settings.
Select “Next” when you are ready to advance.

Figure 10

12) The software will begin installing (Figure 11). Please wait up to 10 minutes.

Figure 11


13) Once the software has been installed, you will reach the ‘Data Collection Agreement’ (Figure
12). Read the screen and when you are ready to continue with the setup, select ‘Next.’

Figure 12

14) The installation is now complete (Figure 13). To open the software/application, select ‘START.’

Figure 13


15) Once the software opens, you will be 16) Read the Software License Agreement.
prompted to setup the software (Figure 14). If you accept the terms, click in the empty box
Select your language and region. Click “Next”. to accept the terms (Figure 15). Click “Next”.

Figure 14 Figure 15



17) Next step is to set the filepath for your data 18) Read the agreement to participate in
(Figure 16). Most customers can use the anonymous usage logs to help improve the
default settings. Once this is set, click “Next”. software (Figure 17). If you agree, check the
box. If you do not agree, leave the box unchecked.
Once you have decided, click “Star inLab CAD”.

Figure 16 Figure 17

19) inLab CAM 22 is now setup. You will need to enter your license key to exit demo mode.
Complete the install of ALL Applications first (if you have more to install), and then follow the
‘License Key Entry and Activation’ instructions.

REVIEW IMPORTANT NOTES ON PAGE 1 IF NOT ALREADY DONE.


inLab Applications
inLab Model
1) Run windows updates and verify that your system is up-to-date (if not already performed
earlier).
2) Open the inLab Applications folder and double-click the inLab Model setup file (Figure 1) to
start the installation process (or right click and select ‘run’).

Figure 1

3) The installation process will begin with the software asking you to select the appropriate
language (Figure 2) and click “Next” twice.

Figure 2


4) Review the License Agreement. Accept the license agreement terms by checking the empty
box (Figure 3). Click ‘Next’ to advance.

Figure 3

5) Select the location in which you would like to install the application (Figure 4). Most
customers can leave the default settings. When you are ready to advance, click “Next”.

Figure 4

6) If prompted by your computer, “Do you want to allow this app to make changes to your
device?” select ‘Yes’.


7) The software will begin installing (Figure 5). Please wait up to 10 minutes.

Figure 5

8) The installation is now complete. Leave “Start the plugin directly” unchecked
and click “Close”. NOTE: This will replace any previous inLab Model software
versions, unlike the CAD or CAM installs.


inLab Partial Framework
1) Run windows updates and verify that your system is up-to-date (if not already performed
earlier).
2) Open the inLab Applications folder and double-click the inLab Partial Framework
setup file (Figure 1) to start the installation process (or right click and select ‘run’).

Figure 1

3) The installation process will begin with the software asking you to select the appropriate
language (Figure 2) and click “Next” twice.

Figure 2


4) Review the License Agreement. Accept the license agreement terms by checking the empty
box (Figure 3). Click ‘Next’ to advance.

Figure 3

5) Select the location in which you would like to install the application (Figure 4). Most
customers can leave the default settings. When you are ready to advance, click “Next”.

Figure 4

6) If prompted by your computer, “Do you want to allow this app to make changes to your
device?” select ‘Yes’.


7) The software will begin installing (Figure 5). Please wait up to 10 minutes.

Figure 5

8) The installation is now complete. Leave “Start the plugin directly” unchecked
and click “Close”. NOTE: This will replace any previous inLab Partial Framework
software versions, unlike the CAD or CAM installs.


inLab Splint
1) Run windows updates and verify that your system is up-to-date (if not already performed
earlier).
2) Open the inLab Applications folder and double-click the inLab Splint setup file (Figure 1) to
start the installation process (or right click and select ‘run’).

Figure 1

3) The installation process will begin with the software asking you to select the appropriate
language (Figure 2) and click “Next” twice.

Figure 2


4) Review the License Agreement. Accept the license agreement terms by checking the empty
box (Figure 3). Click ‘Next’ to advance.

Figure 3

5) Select the location in which you would like to install the application (Figure 4). Most
customers can leave the default settings. When you are ready to advance, click “Next”.

Figure 4

6) If prompted by your computer, “Do you want to allow this app to make changes to your
device?” select ‘Yes’.


7) The software will begin installing (Figure 5). Please wait up to 10 minutes.

Figure 5

8) The installation is now complete. Leave “Start the plugin directly” unchecked
and click “Close”. NOTE: This will replace any previous inLab splint software
versions, unlike the CAD or CAM installs.



License Key Entry and Activation
1. Make sure your Blue or Yellow Dentsply Sirona USB dongle is plugged into a USB port on
your computer (Figure 1).

Figure 1

2. Open up inLab CAD or inLab CAM. When the software opens, select the ‘Menu’
button (DS Logo) in the top left corner and navigate to License Key Manager (Figure 2).
Click on ‘License Manager.’ The License Manager window will open.

Figure 2


3. Before you activate your license keys, make sure your USB dongle’s firmware is updated.
Click on the ‘Status’ icon. This will take you to the available licenses on your USB. Click on
Firmware Update (Figure 3) and follow the steps to update the USB firmware.

Figure 3

4. Once your USB is firmware is updated. Go back to the introduction step. Read the introduction
and then select ‘Next’ (Figure 4).

Figure 4


5. The first step in the process is to check your Internet Connection. Make sure your inLab PC is
connected to the internet to make this step go faster. Then click ‘Check Internet Connection’
(Figure 5).

Figure 5

6. If your inLab PC is connected to the internet, you’ll advance to the third step where you will
enter the 25-character license key (Figure 6) that was provided to you in your software
download email from Dentsply Sirona Lab. If you are…

i. Activating your inLab CAD, type in the CAD license key without the dashes
ii. Activating your inLab CAM, type in the CAM license key without the dashes

Figure 6

Once you have entered the appropriate license key, the software will quickly validate if it’s a
registered key and provide either a green check (Figure 6) and advance to Figure 7 or a
red warning. If you get a red warning sign please contact your preferred distributor for help
(e.g. Patterson PTC or Zahn CAP).


7. If you advance to Figure 7 below, select ‘Activate’ to complete the license key activation
process. Wait a moment as the activation key is sent to Dentsply Sirona for validation. Once
validated, you will be taken to the Status Screen (Figure 8) with a congratulations message
confirm the key has been activated on the USB license drive shown.

Figure 7

Figure 8

8. Repeat Steps 6 & 7 for any additional license keys you need to activate. If you don’t have any
additional keys to activate, you are done!

                        
˜         
       ™ š š • › œ › – š š ­Œ     ›
  ˆ              
      ‰ˆ    ™ š š • ž – – š “ œ 

