@AIRBUS

AIRBUS S.A.S.
Customer Services
Technical Data Support and Services
31707 Blagnac Cedex
FRANCE

COMPONENT MAINTENANCE MANUAL

WITH
ILLUSTRATED PART LIST

MOUNT INSTL COMPUTER

PN : A9232076800000
A9232076800100
A9232076800600
A9232076800900
A9232076801000
A9232076801100
A9232076801300
A9232076801700

Issue: Oct 15/82 34-25-37 Rev: Jul 01/09

 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

HIGHLIGHTS

Revision No. 29 - Jul 01/09

LOCATIONS CHG DESCRIPTIONS OF CHANGE

CODE
DISASSEMBLY
Subtask 34-25-37-000-001-A01 R PART EFFECTIVITY
ADDED/REVISED/DELETED
Subtask 34-25-37-000-002-A01 R PART EFFECTIVITY
ADDED/REVISED/DELETED

CLEANING
TASK 34-25-37-100-801-A01 R CONSUMABLE MATERIAL DATA
UPDATED

REPAIR
TASK 34-25-37-300-801-A01 R CONSUMABLE MATERIAL DATA
UPDATED
TASK 34-25-37-300-802-A01 R CONSUMABLE MATERIAL DATA
UPDATED

ASSEMBLY
Subtask 34-25-37-400-001-A01 R PART EFFECTIVITY
ADDED/REVISED/DELETED
Subtask 34-25-37-400-002-A01 R PART EFFECTIVITY
ADDED/REVISED/DELETED

HIGHLIGHTS
Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

LIST OF EFFECTIVE CONTENT

Revision No. 29 - Jul 01/09

CONTENT CHG LAST REVISION

CODE DATE
INTRODUCTION
TASK 34-25-37-871-801-A01 Mar 01/09

DESCRIPTION AND OPERATION

TASK 34-25-37-870-802-A01 Mar 01/09
TASK 34-25-37-870-803-A01 Mar 01/09

DISASSEMBLY
TASK 34-25-37-000-801-A01 Mar 01/09
Subtask 34-25-37-000-001-A01 R Jul 01/09
TASK 34-25-37-000-801-B01 Mar 01/09
Subtask 34-25-37-000-002-A01 R Jul 01/09
TASK 34-25-37-000-801-C01 Mar 01/09
Subtask 34-25-37-000-003-A01 Mar 01/09

CLEANING
TASK 34-25-37-100-801-A01 R Jul 01/09
Subtask 34-25-37-100-001-A01 Mar 01/09

INSPECTION/CHECK
TASK 34-25-37-210-801-A01 Mar 01/09
Subtask 34-25-37-210-001-A01 Mar 01/09

REPAIR
TASK 34-25-37-300-801-A01 R Jul 01/09
Subtask 34-25-37-300-001-A01 Mar 01/09
Subtask 34-25-37-300-002-A01 Mar 01/09
TASK 34-25-37-300-802-A01 R Jul 01/09
Subtask 34-25-37-300-003-A01 Mar 01/09

L.E.C.
Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

CONTENT CHG LAST REVISION

CODE DATE
ASSEMBLY
TASK 34-25-37-400-801-A01 Mar 01/09
Subtask 34-25-37-400-001-A01 R Jul 01/09
TASK 34-25-37-400-801-B01 Mar 01/09
Subtask 34-25-37-400-002-A01 R Jul 01/09
TASK 34-25-37-400-801-C01 Mar 01/09
Subtask 34-25-37-400-003-A01 Mar 01/09

STORAGE INCLUDING TRANSPORTATION

TASK 34-25-37-550-801-A01 Mar 01/09
Subtask 34-25-37-620-001-A01 Mar 01/09
Subtask 34-25-37-530-001-A01 Mar 01/09
Subtask 34-25-37-550-001-A01 Mar 01/09
Subtask 34-25-37-550-002-A01 Mar 01/09

ILLUSTRATED PARTS LIST

IPL Introduction
TASK 34-25-37-872-801-A01 Mar 01/09
VENDOR LIST Mar 01/09
Figure 01
FIGURE 34-25-37-991-801-001 Mar 01/09
Parts List Mar 01/09
Figure 01A
FIGURE 34-25-37-991-801-A01 Mar 01/09
Parts List Mar 01/09
Figure 01B
FIGURE 34-25-37-991-801-B01 Mar 01/09
Parts List Mar 01/09

L.E.C.
Page 2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

LIST OF SERVICE BULLETINS

SB No REV No MOD No INCORP. TITLE

DATE
*** NO SB ***

SBL
Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

INTRODUCTION

**For PN’s ALL

TASK 34-25-37-871-801-A01
Introduction
1. General
A. This manual is written to the iSpec 2200 and in ASD Simplified Technical English (STE). The
international SI units of measurement are used in this manual, with imperial units shown in
parentheses.
B. The manual contains data about maintenance on the component in a workshop. It does not
contain data about maintenance on the component when it is installed in the aircraft.
C. Only approved persons with the necessary skills are permitted to do the maintenance procedures
in this manual.
D. Maintenance Task Oriented Support System (MTOSS) task and subtask identification is used in
this manual. The maintenance tasks and other data have special MTOSS numbers for Electronic
Data Processing (EDP). The user of the manual can ignore the MTOSS numbers.
E. This manual contains:
- Technical data for the component
- Maintenance and repair procedures about the component
- An Illustrated Parts List (IPL) with data for the component parts. Parts are identified in all
sections of the manual by the IPL-Figure and item number.
F. We verified the DISASSEMBLY, TESTING and ASSEMBLY procedures by simulation.
2. How to use the Manual
A. Make sure that the manual contains the information applicable to your component.
B. If you need to identify a part or find a part number, use the search function.
C. You must use the instructions in this manual for all the component maintenance. Read all the
applicable WARNINGS and CAUTIONS before you do the work on the component.
3. List of Abbreviations
ACM Abbreviated Component Maintenance Manual
AEB Airline Engineering Bulletin
ASD Aero Space and Defence Industries Association of Europe
ATA Air Transport Association of America
ATLAS Abbreviated Test Language for All Systems
CMM Component Maintenance Manual
CMS Component Maintenance Sheet
FIN Functional Item Number

INTRO
Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

IPC Illustrated Parts Catalog

IPL Illustrated Parts List
ID Inside Diameter
MFG Manufacturing
MFR Manufacturer
MOD Modification
MTOSS Maintenance Task Oriented Support System
NTF Non Textile Floor
OD Outside Diameter
PA Poly-Amide
PARA Paragraph
PC Poly-Carbonate
PMS Process and Materials Specification
PN Part Number
PU Poly-Urethane
PV Poly-Venyl-Fluorite
SB Service Bulletin
SERNO Serial Number
STE Simplified Technical English
TBD To Be Determined
List of Abbreviations
TABLE 1

INTRO
Page 2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

DESCRIPTION AND OPERATION

**For PN’s ALL

TASK 34-25-37-870-802-A01
General
1. The computer mount assembly is a mounting an which gyroscopic units are installed. A ventilation
system is provided to enable gyroscopic unit cooling.
2. Characteristics
A. Overall Dimension
Width: 264 mm (10.4 in.)
Height: 127 mm (5 in.)
Length: 527.3 mm (20.76 in.)
Technical Data
TABLE 1

Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s ALL

TASK 34-25-37-870-803-A01
Description
1. This assembly consists of an unequipped mount mode of a lower plate, an upper plate, a stiffener, a
gusset and an angle. The component parts are all riveted.
2. Three locating pins enable correct positioning of gyroscopic units. The gyroscopic units are secured in
position by means of two adjustable fork assemblies.
3. The ventilation system consists of a cooling aperture, a protective grille assy and an adaptor assy.

Page 2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

DISASSEMBLY

**For PN’s A9232076800000 A9232076800100 A9232076800600

TASK 34-25-37-000-801-A01
Disaassembly
1. Reason for the Job
Self explanatory.
2. Procedure

Subtask 34-25-37-000-001-A01
A. Disassembly

NOTE : IPL_FIGURE_01
VARIANT 1
(1) Alternative with shim
(a) Remove the six bolts (10) and washers (20)
(b) Remove grille (50), seal (40) and adapter (30)
(c) Remove nuts (90) and locating pins (100 and 110)
(d) Remove cut (120), washer (130) and screw (140)
(e) Remove shim (150)
(f) Remove screws (60) and (70)
(g) Remove seal assy (80)
(h) Remove nut (160), washer (170) and screw (180)
(i) Remove adjustable fork assy (190).
VARIANT 2
(1) Alternative without shim
(a) Remove the six bolts (10) and washers (20)
(b) Remove grille (50), seal (40) and adapter (30)
(c) Remove nuts (90) and locating pins (100 and 110)
(d) Remove screws (60) and (70)
(e) Remove seal assy (80)
(f) Remove nut (160), washer (170) and screw (180)
(g) Remove adjustable fork assy (190).

Page 3001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s A9232076800900 A9232076801000 A9232076801100 A9232076801300

TASK 34-25-37-000-801-B01
Disassembly
1. Reason for the Job
Self explanatory.
2. Procedure

Subtask 34-25-37-000-002-A01
A. Disassembly

NOTE : IPL_FIGURE_01A
VARIANT 1
(2) Alternative with shim
(a) Remove quick release fasteners (40)
(b) Remove protective grille assy (50) R
(c) Remove screws (10), shim (60), seal (30) and adapter (20)
(d) Remove nuts (100) and locating pins (110) and (120)
(e) Remove nuts (130), washers (140) and screw (150)
(f) Remove shim (160)
(g) Remove screws (70) and (80)
(h) Remove seal assy (90)
(i) Remove nut (170), washer (180) and screw (190)
(j) Remove adjustable fork assy (200).
VARIANT 2
(2) Alternative without shim
(a) Remove quick release fasteners (40)
(b) Remove protective grille assy (50)
(c) Remove screws (10), shim assy (60), seal (30) and adapter (20)
(d) Remove nuts (100) and locating pins (110) and (120)
(e) Remove screws (70) and (80)
(f) Remove seal assy (90)
(g) Remove nut (170), washer (180) and screw (190)
(h) Remove adjustable fork assy (200).

Page 3002
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s A9232076801700

TASK 34-25-37-000-801-C01
Disassembly
1. Reason for the Job
Self explanatory.
2. Procedure

Subtask 34-25-37-000-003-A01
A. Disassembly

NOTE : IPL_FIGURE_01A
(1) Remove nuts (40) and Locating pins (50) (60)
(2) Remove screws (10) (20)
(3) Remove real assembly (30)
(4) Remove nut (70), washer (80) and screw (90)
(5) Remove adjustable fork assembly (100).

Page 3003
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

CLEANING

**For PN’s ALL

TASK 34-25-37-100-801-A01
Cleaning
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.

CAUTION : USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR

EQUIVALENTS. THE SURFACE PROTECTION COULD BE DAMAGED IF
UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE
MANUFACTURER’S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS
ARE FOLLOWED.
Not applicable
2. Job Set-up Information
A. Consumable Materials
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
19-003 Lint-Free Cotton Cloth
Consumable Materials
TABLE 1

3. Procedure

Subtask 34-25-37-100-001-A01
A. Cleaning
(1) The mount assembly component parts must be cleaned as follows:
(a) Remove debris and loose dirt.

Page 4001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 11-003 METHYL-

ETHYL-KETONE. OBEY THE MATERIAL MANUFACTURER’S
INSTRUCTIONS.
(b) Wash component parts with Material No. 11-003 Methyl-Ethyl-Ketone. Soft brush
cleaning is recommended.
(c) Dry the cleaned component parts with a dry, clean Material No. 19-003 Lint-Free
Cotton Cloth.

Page 4002
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

INSPECTION/CHECK

**For PN’s ALL

TASK 34-25-37-210-801-A01
Check
1. General
A. All the component parts of the unequipped mount must be checked (front plate, gusset, angle,
lower and upper plates, stiffener). Check condition of rivets an unequipped mount.
2. Procedure

Subtask 34-25-37-210-001-A01
A. Check of the Component Parts of the Mount Assembly
(1) General condition
(a) Check that mount is not out of true. If deformed, it must be replaced.
(2) Scratches
(a) Scratches may be removed to a depth of 0.2 mm (0.008 in.) and a maximum length
of 20 mm (0.79 in.).
(3) Corrosion
(a) Replace locating pins if corroded. On all the other component parts, corrosion may be
removed to a depth of 0.2 mm (0.008 in.) and up to an area of 80 sq. mm (0.12 sq.
in.).

Page 5001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

REPAIR

**For PN’s ALL

TASK 34-25-37-300-801-A01
Reworking
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.

CAUTION : USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR

EQUIVALENTS. THE SURFACE PROTECTION COULD BE DAMAGED IF
UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE
MANUFACTURER’S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS
ARE FOLLOWED.
-
-

NOTE : For limits of damage to component parts, refer to INSPECTION /CHECK TASK
34-25-37-210-801-A01.
2. Job Set-up Information
A. Consumable Materials
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
19-011 Scotch Brite Pads
Consumable Materials
TABLE 1

Page 6001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

B. Fixtures, Tools, Test and Support

REFERENCE DESIGNATION
buffing wheel
Fixtures, Tools, Test and Support
TABLE 2

C. Referenced Information
REFERENCE DESIGNATION
TASK 34-25-37-210-801-A01 TASK 34-25-37-210-801-A01-Check
TASK 34-25-37-300-802-A01 TASK 34-25-37-300-802-A01-Protective Treatment
Referenced Information
TABLE 3

3. Procedure

Subtask 34-25-37-300-001-A01
A. Repair of Corroded Component Parts
(1) Remove surface protection from corroded area with abrasive cloth.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 11-003 METHYL-ETHYL-

KETONE. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS.
(2) Clean and degrease corroded area with Material No. 11-003 Methyl-Ethyl-Ketone and dry
it.
(3) Remove corrosion deposits.
(a) Clear the surface surrounding the damaged area.
(b) Remove corrosion and polish worked area with Scotch Brite blending into surrounding
unworked area.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 11-003 METHYL-

ETHYL-KETONE. OBEY THE MATERIAL MANUFACTURER’S
INSTRUCTIONS.
(c) Clean and degrease worked area with Material No. 11-003 Methyl-Ethyl-Ketone and
dry it.
(4) Make certain that area is free from corrosion and crack formation.

NOTE : It is important that corrosion is completely removed before the damaged area is
treated, as even the smallest residue can initiate new corrosion.

Page 6002
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

Subtask 34-25-37-300-002-A01
B. Repair of Scratches

CAUTION : WIDTH OF DEPRESSION AFTER REPAIR MUST NOT EXCEED 6 MM (0.24

IN.).
(1) Hollow out scratch to form a shallow depression. Remove minimum possible amount of
material so that width does not exceed 6 mm (0.24 in.).
(2) Blend depression with Material No. 19-011 Scotch Brite Pads.
(3) Polish the surface by hand or with buffing wheel .
(4) Repair damaged paintwork as described in TASK 34-25-37-300-802-A01.

Page 6003
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s ALL

TASK 34-25-37-300-802-A01
Protective Treatment
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.

CAUTION : USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR

EQUIVALENTS. THE SURFACE PROTECTION COULD BE DAMAGED IF
UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE
MANUFACTURER’S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS
ARE FOLLOWED.
-
-

NOTE : For limits of damage to component parts, refer to INSPECTION /CHECK TASK
34-25-37-210-801-A01.
2. Job Set-up Information
A. Consumable Materials
REFERENCE DESIGNATION
11-003 Methyl-Ethyl-Ketone
13-002 Chemical Conversion Coating Yellow Aluminum
16-006 Anti Corrosion Primer (Epoxy-Improved Adhesion)
16-002 Polyurethane Topcoat Grey (for Internal Applic.)
Consumable Materials
TABLE 1

Page 6004
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

B. Fixtures, Tools, Test and Support

REFERENCE DESIGNATION
abrasive cloth
Fixtures, Tools, Test and Support
TABLE 2

C. Referenced Information
REFERENCE DESIGNATION
TASK 34-25-37-210-801-A01 TASK 34-25-37-210-801-A01-Check
Referenced Information
TABLE 3

3. Procedure

Subtask 34-25-37-300-003-A01
A. Protective Treatment
(1) Remove damaged paintwork with abrasive cloth.
(2) Remove debris.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 11-003 METHYL-ETHYL-

KETONE. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS.
(3) Clean and degrease worked area with Material No. 11-003 Methyl-Ethyl-Ketone then dry it.
After cleaning do not handle worked area.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 13-002 CHEMICAL

CONVERSION COATING YELLOW ALUMINUM. OBEY THE MATERIAL
MANUFACTURER’S INSTRUCTIONS.
(4) Apply Material No. 13-002 Chemical Conversion Coating Yellow Aluminum with a brush
and allow to dry.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 16-006 ANTI CORROSION
PRIMER (EPOXY-IMPROVED ADHESION). OBEY THE MATERIAL
MANUFACTURER’S INSTRUCTIONS.
(5) Apply Material No. 16-006 Anti Corrosion Primer (Epoxy-Improved Adhesion) and allow to
dry.

WARNING : BE CAREFUL WHEN YOU USE MATERIAL NO. 16-002 POLYURETHANE

TOPCOAT GREY (FOR INTERNAL APPLIC.). OBEY THE MATERIAL
MANUFACTURER’S INSTRUCTIONS.

Page 6005
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

(6) Apply Material No. 16-002 Polyurethane Topcoat Grey (for Internal Applic.) and allow to
dry.

Page 6006
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

ASSEMBLY

**For PN’s A9232076800000 A9232076800600 A9232076801000

TASK 34-25-37-400-801-A01
Assembly
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.
-
-

NOTE : The spring must be compressed prior to installation of adjustable fork assemblies. The load
threshold required to separate the circlips from the adjustable fork assembly must be equal
to 24 ± 3 daN (54 ± 7 lbf). This Load must be imperatively measured with a
dynamometer.
In order to improve sliding of unit on mount, it is necessary to apply talcum powder to
rubber seat of mount or to spray Molykote Spray G material on same seal. In the latter
case, it is necessary to allow Molykote Spray G material to dry for 5 days minimum before
sliding gyroscopic unit on mount.
2. Procedure

Subtask 34-25-37-400-001-A01
A. Assembly

NOTE : IPL_FIGURE_01
VARIANT 1
(1) Alternative with shim
(a) Install shim (150) secure with screw (140), washer (130), and nut (120).
(b) Install locating pins (110) and secure by means of nut (90).

Page 7001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

(c) Install grille (50), seal (40), adaptor assy (30) secure by means of bolt (10) and
washer (20).
(d) Install seal assy (80) ; secure with screws (60) and (70).
(e) Install locating pin (100) secure with nuts (90).
(f) Install adjustable fork assy (190) ; secure with nut (160), washer (170) and screw
(180).
VARIANT 2
(1) Alternative without shim
(a) Install locating pins (110C) ; secure with nut (90).
(b) Install grille (50), seal (40), adapter (30) ; secure with bolt (10) and washer (20).
(c) Install seal assy (80) ; secure with screws (60) and (70).
(d) Install locating pin (100) ; secure with nuts (20).
(e) Install adjustable fork assemblies (190) ; secure with nut (160), washer (170) and
screw (180).

Page 7002
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s A9232076800100 A9232076800900 A9232076801100 A9232076801300

TASK 34-25-37-400-801-B01
Assembly
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.
-
-

NOTE : The spring must be compressed prior to installation of adjustable fork assemblies. The load
threshold required to separate the circlips from the adjustable fork assembly must be equal
to 24 ± 3 daN (54 ± 7 lbf). This Load must be imperatively measured with a
dynamometer.
In order to improve sliding of unit on mount, it is necessary to apply talcum powder to
rubber seat of mount or to spray Molykote Spray G material on same seal. In the latter
case, it is necessary to allow Molykote Spray G material to dry for 5 days minimum before
sliding gyroscopic unit on mount.
2. Procedure

Subtask 34-25-37-400-002-A01
A. Assembly

NOTE : IPL_FIGURE_01A
VARIANT 1
(2) Alternative with shim
(a) Install shim (160) ; secure with screw (150), washer (140) and nut (130).
(b) Install locating pins (120B) secure with nut (100).
(c) Install shim (60), seal (30) and adapter (20) secure with R screw (10).
(d) Install protective grille assy (50) ; secure with quick release fasteners.

Page 7003
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

(e) Install seal assy (90) ; secure with screws (70) and (80).
(f) Install locating pin (110) secure with nut (100).
(g) Install adjustable fork assemblies (200) ; secure with nuts (170), washer (180) and
screw (190).
(3) Alternative without shim
(a) Install locating pins (120C) ; secure with nut (100).
(b) Install shim assy (60), seal (30), adapter (20) secure screw (10).
(c) Install prospective grille assy (50) secure with quick release fasteners.
(d) Install seal assy (90) ; secure with screws (70) and (80).
(e) Install locating pin (110) ; secure with nut (100).
(f) Install adjustable fork assemblies (200) secure with nuts (170), washer (180) and
screw (190).

Page 7004
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

**For PN’s A9232076801700

TASK 34-25-37-400-801-C01
Assembly
1. General

WARNING : BE CAREFUL WHEN YOU USE SOLVENTS/CLEANING AGENTS, SEALANTS AND

OTHER MATERIALS. OBEY THE MATERIAL MANUFACTURER’S INSTRUCTIONS
AND THE LOCAL REGULATIONS. MAKE SURE THAT THERE IS A GOOD FLOW
OF AIR THROUGH THE WORK AREA. DO NOT BREATHE THE FUMES. DO NOT
SMOKE. DO NOT USE THESE MATERIALS NEAR A FLAME, SPARKS OR
SOURCES OF HEAT. USE PROTECTIVE CLOTHING, GOGGLES AND GLOVES. IF
YOU GET ONE OF THESE MATERIALS ON YOUR SKIN OR IN YOUR EYES,
FLUSH IT AWAY WITH A FLOW OF CLEAN WATER. IF YOU GET ONE OF
THESE MATERIALS IN YOUR MOUTH, GET IMMEDIATE MEDICAL AID. IN
GENERAL, THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
IRRITANTS.
-
-

NOTE : The spring must be compressed prior to installation of adjustable fork assemblies. The load
threshold required to separate the circlips from the adjustable fork assembly must be equal
to 24 ± 3 daN (54 ± 7 lbf). This Load must be imperatively measured with a
dynamometer.
In order to improve sliding of unit on mount, it is necessary to apply talcum powder to
rubber seat of mount or to spray Molykote Spray G material on same seal. In the latter
case, it is necessary to allow Molykote Spray G material to dry for 5 days minimum before
sliding gyroscopic unit on mount.
2. Procedure

Subtask 34-25-37-400-003-A01
A. Procedure as per

NOTE : IPL_FIGURE_01B
(1) Install Locating pins (50) (60) ; secure with nuts (40).
(2) Install seal assembly (30) ; secure with screws (10) (20).
(3) Install adjustable fork assemblies (100) ; secure with nuts (70), washers (80) and screws
(90).

Page 7005
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

STORAGE INCLUDING TRANSPORTATION

**For PN’s ALL

TASK 34-25-37-550-801-A01
Storage
1. General
A. The component should be stored in its original packing. Avoid damage caused by excessive
weight, if stacked storage is used.
B. The packed component must be stored in a clean, dry, ventilated room. The storage
temperature must be kept between 18˚C (64˚F) and 28˚C (82˚F), preferably nearer the Lower
Limit. If rubber parts are installed an the component the temperature should not exceed + 20˚C
(+ 68˚F).
C. The relative humidity should be between 25% and 65 %.
D. The packed component must not be stored in the vicinity of corrosive fluids or near heat or
ozone generating sources.
E. The package must be positioned so that the identification Label can be checked easily.
2. Job Set-up Information
A. Referenced Information
REFERENCE DESIGNATION
TASK 34-25-37-870-802-A01 TASK 34-25-37-870-802-A01-General
Referenced Information
TABLE 1

3. Procedure

Subtask 34-25-37-620-001-A01
A. Preservation
(1) Before packing for storage, the component must be preserved in accordance with
Specification NIL-P-116.

Subtask 34-25-37-530-001-A01
B. Packing
(1) The component must be packed either in the original packing or in a suitable container, in
accordance with Air Transport Association Specification Number 300 (ATA 300).
(2) If a container is used, cushioning material and bracing must be provided to prevent
accidental damage to fragile components. For dimension of the component refer to
DESCRIPTION AND OPERATION TASK 34-25-37-870-802-A01.

Page 15001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

Subtask 34-25-37-550-001-A01
C. Identification Label
(1) An identification label must be affixed to the component so that it is easily discernable
both before and after packing. If necessary, an additional identification label must be
affixed to the outside of the package.
(2) The identification label must contain all relevant details, including the date of receipt into
storage and dates of condition checks during storage.
(3) If the identification label is missing, the component cannot be approved for installation or
storage.

Subtask 34-25-37-550-002-A01
D. Condition Check
(1) A condition of the component must be carried out at scheduled intervals and before the
component is installed in the aircraft.

Page 15002
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

ILLUSTRATED PARTS LIST

Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

INTRODUCTION

**For PN’s ALL

TASK 34-25-37-872-801-A01
Introduction Illustrated Parts List (IPL)
1. General
A. The procedure recommended for finding a part number, or details of a part are in paragraph 2
of this introduction.
B. The IPL contains:
- illustrations that show an exploded view of the parts,
- the related detailed Parts Lists.
C. The IPL is used to identify, to get, keep and issue replacement aircraft parts and units.
D. AIRBUS S.A.S. has no responsibility for parts and/or units deleted or revised as a result if
airline initiated modifications are included.
E. Part numbers shown in this document are written to Air Transport Association of America
(ATA) Specification ISPEC 2200.
F. Illustrations are applicable to more than one customer.
G. In the Detailed Parts List, each figure has its own page numbering system that starts at zero.
2. How to use the IPL
A. To find a Part Number (P/N) in a Figure or Illustration you can either:
- Enter the PN in the SEARCH tool within the AirN@v / Workshop. This will show you the
Figure or Figures where this appears. Click on your chosen Fig/Item number to go open the
Figure.
- Or refer to the Alph/Numeric Parts List and find the PN. In the Fig/Item column it will
show you all the figures where this PN exists, and the Item number. Click one of these to
open the Figure.
3. Plan of the IPL
A. Indenture System of the Detailed Parts List
(1) The indenture system shows how parts and assemblies relate to their next higher
assemblies (NHA) as follows:
1234567
Assembly
Attaching parts for assembly
.Detail parts for assembly
.Sub-assembly
..Detailed parts for sub-assembly
..Sub-sub-assembly

IPL INTRO
Page 1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

...Detailed parts for sub-sub-assembly.

B. AIRBUS Part -- Numbering System
(1) The example that follows shows the identification of a part/assembly:
Basic Part Number L 57 4 6 0200 000 00
DRAWING NUMBER PARTS LIST DATA
AIRBUS Part -- Numbering System
TABLE 1

(1) L Aircraft A = AIRBUS A310/A300/A300-600 Aircraft

D = AIRBUS A320 Aircraft
F = AIRBUS A340 Aircraft
L = AIRBUS A380 Aircraft
NOTE: Initial aircraft type the part assembly was
first used on.
(2) 57 ATA Chapter Design and Manufacturing requirements of the
above breakdown will not always be the same as
those in the ATA Specification and the IPL.
(3) 4 ATA Section Changes with the ATA Chapter.
(4) 6 Drawing The Engineering Department that is responsible
Responsibility for the Design.
(5) 0200 Drawing Number The Drawing number.
(6) 000 Part or Assembly Part/assembly number.
(7) 00 Technical Manufacturing or spares requirements suffix.
Specification
AIRBUS Part -- Numbering System
TABLE 2

C. Suffixes
SUFFIXES DEFINITION REMARKS
00 and 40 to 49 Production Part to drawing The same as the Production
01 to 39 Production Part not to drawing Part.
50 Spare Part to drawing Spare part is not the same as the
51 to 59 Spare Part not to drawing Production Part
60 to 89 Spare Part not to drawing and Number for Product Support
not storable Breakout, but not for Production
99 Spare Part to drawing and not
storable
90 to 94 Specific Part for Repair Kits

IPL INTRO
Page 2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

SUFFIXES DEFINITION REMARKS

95 to 98 Specific Part for Service Bulletin
Kits
Suffixes
TABLE 3

D. D. Detailed composition for an IPL

Column Column 2 Column 3 Column 4 Column
1 5
FIG- PART NUMBER 1234567 NOMENTLATURE USAGE UNIT
ITEM FROM TO PER
ASSY
1 -- 1A L5217605100000 ARM ASSY-SUPPORT EFF//NHA RF
1 -- 2A L5217605100100 ARM ASSY-SUPPORT EFF//NHA RF
10A L5217605100100 .SUPPORT ASSY (LH) ) (V2D671) 1
SEE 52-10-50-02 FOR DET
20A L5217605500300 .SUPPORT ASSY (RH) (V2D671) 1
SEE 52-10-50-02 FOR DET
*** L5217605501100 .SUPPORT ASSY (V2D671) SPARE
30A L5217609020000 .SHEET-BONDING (V2D671) 2
40A ABS0114T3-1 .BOLT V2D671) 18
50A NAS1149C0363R .WASHER (V80205) 21
60A L9247100502400 .STRAP-BONDING (V2D671) 3
70A L9247100500400 .STRAP-BONDING (V2D671) 1
80A L9247100501400 .STRAP-BONDING (V2D671) 1
90A L5217608620000 .BRACKET-DOOR (V2D671) 1
100A ABS0114T5-25 .BOLT (V2D671) 1
110A L5217608720000 .WASHER-TOOTHED (V2D671) 2
120A NAS1149C0532R .WASHER (V80205) 1
130A NAS1291C5M .NUT (V80205) 1
OPT TO H42-5 (V15653)
OPT TO PLH55M
(VF0224)
OPT TO VN300D054
(V92215)
140A L5217605600000 .BRACKET ASSY (V2D671) 2

IPL INTRO
Page 3
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

Column Column 2 Column 3 Column 4 Column

1 5
*** L5217605600200 .BRACKET ASSY (V2D671) SPARE
145A L5217605620000 ..BRACKET (V2D671) EFF/NHA 1
USED WITH
L5217605600000
*** L5217605620200 ..BRACKET (V2D671) SPARE
150A MS21209F4-15 ..INSERT (V96906) EFF/NHA 1
USED WITH
L5217605600000
160A L5217607600000 .BUMPER ASSY (LH) (V2D671) 1
170A L5217607600100 .BUMPER ASSY (RH) (V2D671) 1
180A L5217607800000 ..BRACKET ASSY (LH) (V2D671) 1
190A L5217607800100 ..BRACKET ASSY (RH) (V2D671) 1
200A L5217607820000 ...BRACKET (LH) (V2D671) 1
210A L5217607820100 ...BRACKET (RH) (V2D671) 1
220A D5237111620400 ...BUSHING-SHOULDERED (V2D671) 1
230A L5217608000000 ..STOP ASSY (V2D671) 1
240A L5217608120000 ...STOP (V2D671) 1
250A L5217608220000 ...SUPPORT (V2D671) 1
260A ABS0114T5-15 ..BOLT (V2D671) 1
270A NAS1291C5M ..NUT (V80205) 1
OPT TO H42-5 (V15653)
OPT TO PLH55M
(VF0224)
OPT TO VN300D054
(V92215)
Detailed composition for an IPL
TABLE 4

IPL INTRO
Page 4
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

(1) Help for the IPL-Page example

Column 1 Figure Number The figure number refers to its
related illustration.
Modifications and system
variants can cause a different
figure. It will be added with a
sequential alpha-suffix, e.g.
modified versions of Figure 1
would be Figure 1A then Figure
1B and so on.
Non-Illustrated Parts The dash before an item
number shows it is not
illustrated.
Item Number Initially, only every tenth
number is used for item
numbers so that other items
can be added later.
Column 2 AIRBUS Part AIRBUS manufactured parts e.
g. L5217605600000
Standard Part A standard part such as AN,
MS, NAS ...., is not given a
supplier code.
Column 3 See XX-XX-XX-XX for DET or Identifies correctly:
NHA - the location of the full
breakdown of a sub-assembly
in the IPL
- the location of the NHA of
the item in the IPL.
Usage From To In the Usage From To field the
statement ”EFF//NHA”
related to an NHA. At the
same time in the Nomenclature
Field under the description of
the Part A Statement ”Used
With ***” will state the NHA
PNR.
Symmetrical Parts LH or RH identifies the left
hand or right hand position of
the part. If a part is only on
one assembly, (LH side) or (RH
side) follows its name.

IPL INTRO
Page 5
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

VENDOR CODE A supplier code is given to the

parts manufactured by firms
other then AIRBUS.
Non-Procurable Item (NP) Identifies an item that is not
supplied.
Column 4 Usage From To In the Usage From To field the
statement ”EFF//NHA”
related to an NHA. At the
same time in the Nomenclature
Field under the description of
the Part A Statement ”Used
With ***” will state the NHA
PNR.
Column 5 Quantity The number in the Units Per
Assy column shows the
quantity of parts used for each
NHA or installation.
AR = as required
RF = reference (quantity
shown in the NHA figure).
Help for the IPL-Page example
TABLE 5

E. Other Notes
(1) ORDER OVRLGTH MPN XXXXXXXXXX
- Identifies a part number with more than fifteen characters that cannot fit in the part
number column.
(2) SB XX-XXX
- Identifies the Service Bulletin (SB) which adds to or changes the Detailed Parts List.
When the SB number shown in the name column is related to an AIRWORTHINESS
DIRECTIVE (AD), the letters AD and its number are shown in parenthesis. Also they
will follow the SB number, for example: PRE SB XX XXX (AD XXXX), POST SB XX
XXX (AD XXXX), ADDED by SB XX XXX (AD XXXX), DELETED BY SB XX XXX
(AD XXX), etc.
(3) SEL FROM
- Identifies a group of alternative parts from which you can take the necessary ones.
(4) OVERSIZE/UNDERSIZE
- Identifies a part as oversize or undersize.
(5) OPT TO
- Identifies an optional part that is fully interchangeable with the initial part.

IPL INTRO
Page 6
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

(6) ALT FROM PN XXXXXXXXXX

- Identifies an alternate part number (this is a part that is fully interchangeable with the
initial part after it has had a change(s)).
(7) BUY PN XXXXXXXXXX
- Identifies the replacement part for the part in the part number column.
(8) LM = LOCAL MANUFACTURE
- Identifies the part number of the basic material (e.g. for seals, hinge strips, extrusion
etc...) from which the part in the part number column is manufactured.
- Identifies the unit of measurement followed by the dimensions or quantity.
(9) SEE CMM OR ACMM
- Refer to the Component Maintenance Manual or Abbreviated Component Maintenance
Manual for the part listed in the Detailed Parts List.
(10) MADE FROM JXXXX, MADE BY VXXXXX, MM XXX
- Identifies a part that is made from bulk material e.g. seals extrusions etc. and, if
necessary, the unit of measurement and quantity.
(11) USED ON MPN
- Identifies the NHA for a part in the part number column. This is used when the NHA
is not clear from the Usage Code (almost the same assemblies with details that are not
the same but have a single breakdown).
(12) VENDOR CODE
(a) These codes agree with the current issue of the Manufacturers Cataloging Handbook
H4/HB:
- Federal Supply Code for Manufacturing (FSCM) or Commercial and Government
Entity (CAGE) code (United States and Canada only).
- NATO Supply Code for Manufacturers (NSCM) codes (does not include United
States and Canada)
(b) The letter ’V’ comes before the vendors code. For suppliers with no official code,
AIRBUS has given a provisional code. These codes are identified in the supplier table
by the information ”DUMMY CODE”.
- AIRBUS standard parts (Prefix DAN, NSA etc...) are given the supplier code of
the seller of the parts. If there is more than one seller, a dummy supplier code
VT0000 is assigned to the related P/N. In this case, the additional cross-
reference table gives, for each P/N the various supplier codes and their own P/N
if applicable.

NOTE : Suppliers who manufacture parts for which AIRBUS S.A.S. has an exclusive
sale right are not given a vendor code.

NOTE : All relevant Supplier Codes are shown in the ’Vendors Name and Code
List’, which is a part of the IPL INTRO.

IPL INTRO
Page 7
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

VENDOR LIST

CODE NAME AND ADDRESS

V04795 TBIL
V06329 TBIL
V11815 TBIL
V14711 TBIL
V15653 TBIL
V1BGN6 TBIL
V1ER65 TBIL
V27238 TBIL
V32664 TBIL
V52828 TBIL
V56563 TBIL
V5N982 TBIL
V60119 TBIL
V60996 TBIL
V70347 TBIL
V72962 TBIL
V75237 TBIL
V80205 TBIL
V83014 TBIL
V88044 TBIL
V8K160 TBIL
V92215 TBIL
V96906 TBIL
V97928 TBIL
VC5543 TBIL
VC5729 TBIL
VF0188 TBIL
VF0224 TBIL
VF0296 TBIL
VF5442 TBIL
VF6033 TBIL
VF6167 TBIL
VF7411 TBIL
VFAPE3 TBIL
VK4975 TBIL
VK6405 TBIL

IPL INTRO
Page 8
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

CODE NAME AND ADDRESS

VK8753 TBIL
VR1120 TBIL
VU1653 TBIL

IPL INTRO
Page 9
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

DETAILED PARTS LIST

Page 10001
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

F_PL_342537_01_0_01_00

MOUNT-COMPUTER
Figure 01 / FIGURE-34-25-37-950-801-01

Page 10001-0
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
01 - 001A A9232076800000 MOUNT-COMPUTER VFAPE3 RF
01 - 001B A9232076800600 MOUNT-COMPUTER VFAPE3 RF
01 - 001C A9232076801000 MOUNTS INSTL COMPUTER (NP) RF
used on 011C (342537000)
01 010A NSA5089-3-6 . SCREW VF5442 006
Optional Vendor Code 04795, C5543, C5729, F6167,
F7411
used on 001A, 001B, 011C (342537000)
01 020A AN960-10L . WASHER V88044 006
NAS1149F0332P 80205
OPT TO ASNA2397-10L F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 001A, 001B, 011C (342537000)
01 030A NSA8069-64 . ADAPTER VF5442 001
OPT TO 52A388 14711
Optional Vendor Code 04795
used on 001A, 001B, 011C (342537000)
01 040A A9232078420000 . SEAL VFAPE3 001
used on 001A, 001B, 011C (342537000)
01 050A A9232012800000 . GRILLE VFAPE3 001
used on 001A, 001B, 011C (342537000)
01 060A NAS1102-04-6 . SCREW V80205 008
Optional Vendor Code 04795, 06329, 1ER65, 70347,
C5543, C5729, F0188, K8753
used on 001A, 001B, 011C (342537000)
01 070A NAS1102-04-7 . SCREW V80205 006
Optional Vendor Code 04795, C5543, C5729, F0188,
K8753
used on 001A, 001B, 011C (342537000)
01 080A A9232076900000 . SEAL VFAPE3 001
used on 001A, 001B, 011C (342537000)
01 090A NSA5050-4 . NUT VF5442 003
OPT TO HW17-4 K6405
OPT TO NAS1726-4E 80205
OPT TO P7094-4 F0224
OPT TO TLN1000L4 92215
Optional Vendor Code 04795, 15653, 97928, C5543,
C5729
used on 001A, 001B, 011C (342537000)
- ITEM NOT ILLUSTRATED

Page 10001-1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
01 100A A9232066520000 . PIN-LOCATING VFAPE3 001
used on 001A, 001B
01 100B A9232066520100 . PIN-LOCATING VFAPE3 001
used on 011C (342537000)
01 110A A9232066620000 . PIN-LOCATING VFAPE3 002
used on 001A
01 110B A9232098320000 . PIN-LOCATING VFAPE3 002
used on 001B
01 110C A9232066620100 . PIN-LOCATING VFAPE3 002
used on 011C (342537000)
01 120A NAS1291-3 . NUT V80205 002
MS21042L3 96906
OPT TO H14-3 15653
OPT TO RM52LH3324-02 72962
OPT TO T98S1032 11815
OPT TO VN300A02 92215
Optional Vendor Code 04795, 06329, C5543, C5729
used on 001B
01 130A AN960-10L . WASHER V88044 002
NAS1149F0332P 80205
OPT TO ASNA2397-10L F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 001B
01 140A NAS1153-7 . SCREW V80205 002
Optional Vendor Code 04795, 06329, 70347, C5543,
C5729, F0188, K8753
used on 001B
01 150A A9232098220000 . SHIM VFAPE3 001
used on 001B
01 160A NAS1291-08 . NUT V80205 002
MS21042L08 96906
OPT TO H14L08 15653
OPT TO PLH3508M F0224
OPT TO RM52LH3324-82 72962
OPT TO T98S832 11815
OPT TO VN300A82 92215
Optional Vendor Code 04795, 06329, 60119, C5543,
C5729, F0224
used on 001A, 001B, 011C (342537000)
01 170A AN960-8 . WASHER V88044 002
NAS1149FN832P 80205
- ITEM NOT ILLUSTRATED

Page 10001-2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
OPT TO ASNA2397-8 F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 001A, 001B, 011C (342537000)
01 180A NAS1100-08-10 . SCREW V80205 002
Optional Vendor Code F0188, F7411, K8753
used on 001A, 001B, 011C (342537000)
01 190A NSA939519-01 . FORK ASSY-ADJUTABLE VF5442 002
OPT TO H2142K1539 83014
Optional Vendor Code 04795, C5543, C5729
used on 001A, 001B
01 190B NSA939522-01 . FORK ASSY ADJUSTABLE VF5442 002
OPT TO H2142K1842 83014
Optional Vendor Code 83014
used on 011C (342537000)
- ITEM NOT ILLUSTRATED

Page 10001-3
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

F_PL_342537_01_A_01_00

MOUNT COMPUTER
Figure 01A / FIGURE-34-25-37-950-801-A01

Page 10001A-0
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
01A - 001A A9232076800100 MOUNT COMPUTER VFAPE3 RF
01A - 001B A9232076800900 MOUNT-COMPUTER VFAPE3 RF
01A - 001C A9232076801100 MOUNT COMPUTER VFAPE3 RF
01A - 001D A9232076801300 MOUNT COMPUTER VFAPE3 RF
01A 010A NAS1102-3-10 . SCREW V80205 006
Optional Vendor Code 04795, 06329, 1ER65, 70347,
C5543, C5729, F0188, F7411, K8753
used on 001A, 001B, 001C, 001D
01A 020A NSA8069-64 . ADAPTER VF5442 001
OPT TO 52A388 14711
Optional Vendor Code 04795
used on 001A, 001B, 001C, 001D
01A 030A A9232078420000 . SEAL VFAPE3 001
used on 001A, 001B, 001C, 001D
01A 040A NSA5512-1-1-1 . FASTENER VF5442 001
OPT TO HN5G51-1 83014
OPT TO HN5P51-1-1 F6033
Optional Vendor Code 04795
used on 001A, 001B, 001C, 001D
01A 050A A9232013700000 . GRILLE-PROTECTIVE VFAPE3 001
OPT TO A9232013700001 FAPE3
used on 001A, 001B, 001C, 001D
01A 060A A9232013500000 . SHIM VFAPE3 001
used on 001A, 001B, 001C, 001D
01A 070A NAS1102-04-6 . SCREW V80205 008
Optional Vendor Code 04795, 06329, 1ER65, 70347,
C5543, C5729, F0188, K8753
used on 001A, 001B, 001C, 001D
01A 080A NAS1102-04-7 . SCREW V80205 006
Optional Vendor Code 04795, C5543, C5729, F0188,
K8753
used on 001A, 001B, 001C, 001D
01A 090A A9232076900000 . SEAL VFAPE3 001
used on 001A, 001B, 001C, 001D
01A 100A NSA5050-4 . NUT VF5442 003
OPT TO HW17-4 K6405
OPT TO NAS1726-4E 80205
OPT TO P7094-4 F0224
OPT TO TLN1000L4 92215
Optional Vendor Code 04795, 15653, 97928, C5543,
C5729
- ITEM NOT ILLUSTRATED

Page 10001A-1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
used on 001A, 001B, 001C, 001D
01A 110A A9232066520000 . PIN-LOCATING VFAPE3 001
used on 001A, 001B
01A 110B A9232066520100 . PIN-LOCATING VFAPE3 001
used on 001C, 001D
01A 120A A9232066620000 . PIN-LOCATING VFAPE3 002
used on 001A
01A 120B A9232066620100 . PIN-LOCATING VFAPE3 002
used on 001C
01A 120C A9232098320000 . PIN-LOCATING VFAPE3 002
used on 001B
01A 120D A9232098320100 . PIN-LOCATING VFAPE3 002
used on 001D
01A 130A NAS1291-3 . NUT V80205 002
MS21042L3 96906
OPT TO H14-3 15653
OPT TO RM52LH3324-02 72962
OPT TO T98S1032 11815
OPT TO VN300A02 92215
Optional Vendor Code 04795, 06329, C5543, C5729
used on 001B, 001D
01A 140A AN960-10L . WASHER V88044 002
NAS1149F0332P 80205
OPT TO ASNA2397-10L F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 001B, 001D
01A 150A NAS1153-7 . SCREW V80205 002
Optional Vendor Code 04795, 06329, 70347, C5543,
C5729, F0188, K8753
used on 001B, 001D
01A 160A A9232098220000 . SHIM VFAPE3 001
used on 001B, 001D
01A 170A NAS1291-08 . NUT V80205 002
MS21042L08 96906
OPT TO H14L08 15653
OPT TO PLH3508M F0224
OPT TO RM52LH3324-82 72962
OPT TO T98S832 11815
OPT TO VN300A82 92215
Optional Vendor Code 04795, 06329, 60119, C5543,
C5729, F0224
- ITEM NOT ILLUSTRATED

Page 10001A-2
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
used on 001A, 001B, 001C, 001D
01A 180A AN960-8 . WASHER V88044 002
NAS1149FN832P 80205
OPT TO ASNA2397-8 F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 001A, 001B, 001C, 001D
01A 190A NAS1100-08-10 . SCREW V80205 002
Optional Vendor Code F0188, F7411, K8753
used on 001A, 001B, 001C, 001D
01A 200A NSA939519-01 . FORK ASSY-ADJUTABLE VF5442 002
OPT TO H2142K1539 83014
Optional Vendor Code 04795, C5543, C5729
used on 001A, 001B
01A 200B NSA939522-01 . FORK ASSY ADJUSTABLE VF5442 002
OPT TO H2142K1842 83014
Optional Vendor Code 83014
used on 001C, 001D
- ITEM NOT ILLUSTRATED

Page 10001A-3
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

F_PL_342537_01_B_01_00

MOUNTS INSTL COMPUTER

Figure 01B / FIGURE-34-25-37-950-801-B01

Page 10001B-0
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
01B - 001A A9232076801700 MOUNTS INSTL COMPUTER (NP) RF
used on 011A (342537000)
01B 010A NAS1102-04-6 . SCREW V80205 008
Optional Vendor Code 04795, 06329, 1ER65, 70347,
C5543, C5729, F0188, K8753
used on 011A (342537000)
01B 020A NAS1102-04-7 . SCREW V80205 006
Optional Vendor Code 04795, C5543, C5729, F0188,
K8753
used on 011A (342537000)
01B 030A A9232076900000 . SEAL VFAPE3 001
used on 011A (342537000)
01B 040A NSA5050-4 . NUT VF5442 003
OPT TO HW17-4 K6405
OPT TO NAS1726-4E 80205
OPT TO P7094-4 F0224
OPT TO TLN1000L4 92215
Optional Vendor Code 04795, 15653, 97928, C5543,
C5729
used on 011A (342537000)
01B 050A A9232066520100 . PIN-LOCATING VFAPE3 001
used on 011A (342537000)
01B 060A A9232066620100 . PIN-LOCATING VFAPE3 002
used on 011A (342537000)
01B 070A NAS1291-08 . NUT V80205 002
MS21042L08 96906
OPT TO H14L08 15653
OPT TO PLH3508M F0224
OPT TO RM52LH3324-82 72962
OPT TO T98S832 11815
OPT TO VN300A82 92215
Optional Vendor Code 04795, 06329, 60119, C5543,
C5729, F0224
used on 011A (342537000)
01B 080A AN960-8 . WASHER V88044 002
NAS1149FN832P 80205
OPT TO ASNA2397-8 F5442
Optional Vendor Code 04795, 06329, 60996, 70347,
8K160, C5543, C5729
used on 011A (342537000)
- ITEM NOT ILLUSTRATED

Page 10001B-1
34-25-37 Jul 01/09
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
A9232076800000

FIG-ITEM PART NUMBER NOMENCLATURE USAGE UNIT

1234567 FROM PER
TO ASSY
01B 090A NAS1100-08-10 . SCREW V80205 002
Optional Vendor Code F0188, F7411, K8753
used on 011A (342537000)
01B 100A NSA939522-01 . FORK ASSY ADJUSTABLE VF5442 002
OPT TO H2142K1842 83014
Optional Vendor Code 83014
used on 011A (342537000)
- ITEM NOT ILLUSTRATED

Page 10001B-2
34-25-37 Jul 01/09