Scribd
Upload
50 views

Abb Ag: Application Characteristics

Uploaded by

Nguyễn Quý
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
50 views

Abb Ag: Application Characteristics

Uploaded by

Nguyễn Quý
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

ABB AG RTU560

Remote Terminal Unit


Data Sheet
Bus Connection Unit 560BCU05

Application Characteristics
The Bus Connection Unit 560BCU05 is designed The Bus Connection Unit 560BCU05 is used in
to make the RTU560s TSI, TSO, Alarm and Warn- the racks 23ET24 and 560SFR02. It is mounted
ing signals accessible to the outside. on the back-side of the rack, and fixed by four
snap-in holders (see figure 2)
By using the bus connection unit 560BCU05, up
to eight communication units (CMUs) can be used The connection to the RTU560 communication
in a configuration. units is made via up to eight connectors to slots
occupied by CMUx Modules. Two connector ca-
To expand the RTU560 system bus to another
bles are delivered with the 560BCU05 R0001.
rack (23ET24, 560SFR02), an 8 pole RJ45 con-
Additional connector cables are available as
nector is available. For cabling, a shielded 8 pole
560BCU05 R0002.
RJ45 patch cable can be used.
All supply voltages and control signals are inter-
faced by a direct Board-to-Board connection. To
enable operation using a 23ET24 rack, +24V
needs to be connected to a screw terminal con-
nector.
The two system signals ALARM and WARNING
can be accessed via relay contacts and are su-
pervised by a watchdog function. If the trigger
from the communication unit is missing for more
than 30 seconds, both relay contacts are acti-
vated.
The external minute interrupt of a real time clock
560RTCxx is connected to the system via an in-
ternal isolated opto-coupler (TSI) and routed to
the time master of the RTU560 system. The min-
ute pulse output (TSO) is available for other appli-
cations.

Figure 1: Function Block Diagram 560BCU05

Doc-No.: 1KGT 150 725 V001 1 1


ABB AG
Data Sheet Bus Connection Unit 560BCU05 RTU560

Board-to-Board connection

BCU05

Mounting
stand-off´s

560SFR02
backplane

Figure 2: Assembly 560SFR02, 560BCU05 R0001

2 Doc.-No.: 1KGT 150 725 V001 1


ABB AG
RTU560 Data Sheet Bus Connection Unit 560BCU05

Technical Data
In addition to the general technical data of the
RTU560, the following applies:

Voltage Supply
Minute Pulse Input (TSI)
Supply 5 V DC / approx. 80 mA
TSI Plug-in terminal strip 2-pole, 24 V DC / approx. 60 mA
24 VDC input, isolated

Minute Pulse Output (TSO) Supply (external)

TSO Plug-in terminal strips 2-pole, +24V Screw terminal connection


24 V DC output only in case of 23ET24 rack

Rack-to-Rack Interface Mechanics

RJ45 connector 180° PCB 126 x 78 mm

Weight Approx. 0.1 kg

Signal Outputs
Connection Type
ALARM Plug-in terminal strips 2-pole
WARNING each Connectors 2 - 8 sub-connectors with flat
cable, 18-pole each
Relay contact Active closed, WARNING is
set also in case of ALARM.
≤ 1 A / ≤ 60 V DC / ≤ 30 W Environmental Conditions

Temperature -40 ... +85 C


Watchdog
Relative 5 ... 95 %
Supervision Approx. 30 seconds humidity (non condensing)
time

Compliances Ordering Information

560BCU05 R0001 1KGT 022400 R0001


EMC EN550011, EN61000
(Basic board + two
Environmental EN60255, IEC60870 connector cables)
Safety EN60950
560BCU05 R0002 1KGT 022400 R0002
(Additional connec-
tor cables)

Doc.-No.: 1KGT 150 725 V001 1 3


ABB AG
Data Sheet Bus Connection Unit 560BCU05 RTU560

ABB AG

Power Technologies Division


Power Technology Systems

Kallstadter Str. 1, 68309 Mannheim


Telephone +49 (0) 621 381 - 7592
Fax +49 (0) 621 381 - 7622
www.abb.com
Subject to alteration

4 Doc.-No.: 1KGT 150 725 V001 1

You might also like