GE

Motors

Standard Products
Catalog
Make GE Your First Choice.
EISAct 2007 EASAct Complaint
President George W. Bush signed the Energy Independence and GE Motors
Security Act (EISAct) December 19, 2007. It requires general purpose X$D Ultra
motors to meet efficiency levels based on NEMA MG1 table 12-12 X$D Ultra 841
within three years from the date of signing (12/19/10). Look for the X$D Ultra 661
EISAct 2007 Compliance sticker to ensure your motor is compliant. Energy $aver

Inverter Capabilities
GE Motors has different insulation systems for motor, which operate on Inverter power. Each system can
withstand a peak Corona Inception Voltage with a rise time of 0.1 microseconds (GEGARD1800 = 1800V peak
CIV @ 0.1 microseconds). All of these systems exceed NEMA MG1-31 (which is 3.1 times nameplate voltage)
for motors operating on inverter power (230, 460 or 575 volt).
Motor Insulation Corona Inception Insulation Application % Exceeding NEMA
Shield Class Voltage Method MG1-31 @ 575V
Dip & Bake or
F 1800V @ 0.1 ms Vacuum Pressure 1%
Impregnation

F 2000V @ 0.1 ms Trickle Treat 10%

GEGARD2400 TM
INVERTER
DUTY
EXCEEDS
NEMA
H 2400V @ 0.1 ms Trickle Treat 26%
MG1-31

GEGARD2800 TM
INVERTER
DUTY
EXCEEDS
NEMA
H 2800V @ 0.1 ms Trickle Treat 36%
MG1-31

Updated Application Guide Now Inside

The AC Motor Selection and Application Guide has been updated and incorporated into this
catalog. It is an excellent tool to assist new employees, customers, specifiers or anyone
who deals with AC motors to better understand terminology, design and applications.

Fire Pump Motor Energy $aver TEFC Motor Pre-Engineered Medium Voltage
Section 6.11 Section 2.5 Section 5.1
GE Motors is proud to introduce a These motors are offered from 1 to Medium voltage up to 4000 HP in
line of motors UL listed for fire 250 HP in 2 and 4 pole designs and 2 and 4 pole designs with TEFC,
pump applications. These motors are built to meet NEMA Premium TEAAC and WPII enclosures. 500
meet UL-1004A and NFPA20 for efficiency levels and incorporate frame designs are in stock for
installation on Centrifugal Fire severe duty features in its immediate delivery. See inside
Pump applications. Available now construction, service factor and for more details.
in 2 and 4 Pole designs. insulation. See inside for more details.

g www.gemotors.com Data subject to change without notice. GEP-500T 04/08.

Table of Contents
iii Product Landscape 3.17
3.17
X$D Ultra® 841
Standard Features
3.18 Pricing
vii Inverter Duty Capabilities 3.22 C-Face Pricing
3.23 460V Performance Data
1.0 Value Line™ Motors 3.25
3.27
575V Performance Data
Dimensions
1.1 Open Dripproof
1.1 Standard Features 3.29 X$D Ultra® 661 for Heat Exchanger
1.2 Pricing 3.29 Standard Features
1.6 NEMA Dimensions 3.30 Pricing
3.31 460V Performance Data
1.7 TEFC and TEFC-Severe Duty 3.32 Dimensions
1.7 Standard Features
1.8 Pricing 3.33 X$D Ultra®, X$D Ultra® 841 and 661 Kits
1.12 C-Face Pricing 140 to 449T
1.14 NEMA Dimensions 3.36 X$D Ultra® Checklist for Value
1.15 C-Face Dimensions
1.17 Explosion Proof 4.0 Adjustable Speed Motors
1.17 Standard Features
1.18 Pricing 4.1 A$D
1.19 NEMA Dimensions 4.1 Standard Features
4.2 Pricing
1.20 Kits and Accessories 4.3 Dimensions
4.6 Kits and Accessories
2.0 Energy $aver® 4.7 A$D Ultra® NEW
NEMA Premium® Motors 4.7 Standard Features
4.8 Pricing
2.1 Open Dripproof
2.1 Standard Features
2.2 Pricing 5.0 Medium Voltage NEW
2.4 Dimensions 5.1 WPII, TEFC, TEAAC Standard Features
2.5 TEFC-Severe Duty NEW 5.2 WPII Pricing and Kits
2.5 Standard Features 5.3 Pegasus™ MHV - WPII Pricing
2.6 Pricing 5.4 Quantum™ LMV - TEFC Pricing
2.9 Dimensions 5.5 Pegasus™ MHV - TEAAC Pricing
5.6 Dimensions
2.8 TEFC-Severe Duty C-Face NEW
2.8 Pricing and Dimensions
6.0 Pump Motors
2.10 Kits and Accessories
6.1 Value Line™ Vertical Hollow Shaft
- Ball Style NRR
3.0 X$D Ultra® 6.1 Standard Features
NEMA Premium® 6.2 Pricing
6.4 Dimensions
Extra Severe Duty Motors 6.5 Kits
3.1 X$D Ultra® – Totally Enclosed Fan Cooled
3.1 Standard Features 6.7 Vertical Solid Shaft Inline Pump
3.2 Pricing 6.7 Standard Features
3.8 C-Face Pricing 6.8 Pricing
3.9 High Torque Design C Pricing 6.9 Dimensions
3.10 460V Performance Data
3.12 575V Performance Data
3.14 Dimensions

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

Table of Contents
6.11 Fire Pump - Open Dripproof NEW 10.0 Application Guide NEW
6.11 Standard Features
6.12 Pricing 10.1 Index
6.13 Dimensions 10.2 Voltage
10.4 Frequency
6.15 High Speed Motor (IP54) 10.5 Motor Output Rating
6.15 Standard Features 10.5 Phase
6.16 Pricing and Kits 10.5 Polyphase Motors
6.17 Dimensions 10.12 Polyphase Motors > 500 Hp
10.12 Service Factor
7.0 DC Motor 10.12 Single-phase Motors
10.13 Motor Temperature
7.1 Standard Features – Kinamatic™ 10.14 Duty Cycle Application
7.2 Shunt Wound - Self Ventilated 10.16 Starting
7.3 Shunt Wound - Separately Ventilated 10.17 Efficiency
7.4 Shunt Wound - Blower Ventilated 10.17 Energy Policy Act (EPAct.)
7.5 Shunt Wound - Totally Enclosed 10.18 NEMA Premium® Efficiency
7.6 Type-K Power Supply – Permanent Magnet 10.19 Efficiency levels, IEC
7.8 PY Tachometers 10.20 Payback Calculations
7.9 BC42 and BC46 Tachometers 10.20 Motor Testing
7.10 12V/24V Battery Supply 10.22 Power Factor
7.11 MG Set Power Supply 10.22 Load Connection
7.12 DC Dimensions 10.25 Load Calculation
7.23 DC Motor Kits and Accessories 10.26 Electrical Construction
7.25 Mill Duty DC Motor - MD800 10.27 Mechanical Construction
10.27 Frame Designation – IEC / NEMA Comparison
8.0 Definite Purpose 10.29 Environmental Considerations
10.33 Model Number Nomenclature
8.1 Appliance
10.34 Modifications, Electrical
8.1 Standard Features
10.36 Modifications, Mechanical
8.2 Pricing
10.39 Modifications, Environmental
8.4 Dimensions
10.39 Vibration Detection
8.5 Farm Duty 10.41 Special and Definite Purpose Applications
8.5 Pricing 10.42 Multi-Speed Motors
8.5 Dimensions 10.44 Application Types, for Industrial Motors
10.46 Adjustable Speed Inverter Duty Operation
8.6 Electric Vehicle - OEM Replacement
10.47 A$D/Load Requirement Data Sheet
8.6 Pricing
10.48 IEC Vs NEMA Mounting Dimension
8.7 Fork Truck / Scissor Lift Truck NEW (Quick Comparison)
8.7 Dimensions 10.49 Historical NEMA Frame Size/Rating designation
8.8 Wash Down Duty - DC
8.8 Pricing 11.0 UL/CSA Motor Listings
8.8 Dimensions
8.9 Premium Efficient Explosion Proof 12.0 Terms and Conditions
8.9 Standard Features
8.10 Pricing
8.12 Dimensions
13.0 Cross Reference Guide
13.1 Catalog Number to Model Number
8.13 X$D® Severe Duty 13.17 Model Number to Catalog Number
8.15 X$D® 841 - Severe Duty

9.0 Modification Center

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

GE Motors

GE Motors has been engineering, testing, and manufacturing high quality motor products for over
125 years. In 1879, GE founder, Thomas Edison constructed the first electric motor ever made for a
110 to 120 Volt line at Menlo Park, NJ. This device still exists and is operative! It is located in the
Edison Historical Collection in New Jersey. Today our capabilities range from 1/20 - 100,000
Horsepower and cross a multitude of industries.

Our Standard Products Catalog includes all cataloged numbered AC and DC motors and kits to meet
your needs. Items marked “Y” under the “Normally Stock” column implies those items are available to
ship from stock at your request. Items marked with an “N” mean that those will be manufactured at
published leads-times, once an order is released. Please refer to “EliteNet” (via www.gemotors.com)
for the latest published lead-times. Each section is meant to include; standard features, pricing,
dimensions, and applicable kits.

We are continually updating www.gemotors.com with the most current information regarding GE
motor products and services.

EliteNet (available via www.gemotors.com) is our web-based tool providing our customers access to
checking stock, order entry, design information, technical data, and much more. EliteNet is an
exclusive web community that connects GE Motors customers and channel partners with a private
password protected web site. A few of the many highlights of EliteNet are listed below:
• 24x7 availability of specific account information
• Private password protected
• Focused, personalized screens of information for everyone in your company
• E-training online to help your staff build their product knowledge
• Register on line via www.gemotors.com

The following websites contain information on GE Motor products along with other
GE products and company initiatives.

www.gemotors.com
www.geindustrial.com
www.ge.com
www.geecomagination.com

You can also reach us by phone:

U.S. & Canada 1-800-541-7191
Parts 1-800-458-0451
International 1-800-447-98180

Thank you for choosing GE Motors!

Product offerings, drawings, data and prices herein are subject to change without notice. Motor weights are estimated.
EliteNet, Energy $aver, X$D Ultra, Kinamatic, K-3, Value Line and E$P are trademarks of General Electric Company.
Copyright ©1990, 1992, 1994, 1996, 1997, 1998, 1999, 2000, 2001, 2004, 2005, 2007 by General Electric Company, USA.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.
 Product Landscape

Feature Value Line ODP Value Line Epact TEFC

Frame Size 140-449 140-280 320-360 400-445 447-449
Agency Approvals UL, CSA UL, CSA UL,CSA UL, CSA UL, CSA
Altitude 3300 ft @ 40ºC 3300 @ 40ºC 3300 ft 3300 ft 3303 @ 40ºC
Ambient 40 to -15ºC 40 to -40ºC -10 to 40ºC -10 to 40ºC -10 to 40ºC
Bearing Cap Gasketed Yes, 440 No No No No
Bearing Caps 280TS DE and ODE 280TS Only Yes Yes Yes
Direct Coupled: 65,000 Direct Coupled: 65,000 Direct Coupled: 65,000 Direct Coupled: 65,000 Direct Coupled: 65,000
Bearing Life (hrs.)
Belted: 25,000 Belted: 25,000 Belted: 26,280 Belted: 26,280 Belted: 26,280
Double Shield 140-280T
Bearing Type Shielded (except 280TS) Open Open Single shielded
Open 280TS, 320-449
Conduit Box Steel Steel Cast Iron Cast Iron Cast Iron
Constant Torque 4:1 4:1 2:1 2:1 2:1
Efficiency EPAct to 200Hp EPAct EPAct EPAct EPAct
Endshield Mat’l Cast Iron Cast Iron Cast Iron Cast Iron Cast Iron
External Fan N/A Non-Sparking Non-Sparking Non-Sparking Non-Sparking
Fan Cover N/A Pressed Steel Steel Steel Cast Iron
Frame Mat’l Cast Iron Cast Iron Cast Iron Cast Iron Cast Iron
Lithium 140-280T,
Grease Lithium Polyurea Polyurea Polyurea
Polyurea 320-449
Grounding Term. Bolt in Cond Box Bolt in Cond Box Bolt in Cond Box Bolt in Cond Box Bolt in Cond Box
Hardware Grade ISO 8.8 ISO 4.8 ISO 8.8 ISO 8.8 ISO 8.8
Hardware Type Metric Metric SAE SAE SAE
Insulation Type GEGARD1800™ F GEGARD1800™ F GEGARD1800™ F GEGARD1800™ F GEGARD1800™ F
140 frame - None
Lifting Means Eyebolt Eyebolt Eyebolt Eyebolt
All others - Eyebolt
Lubrication Regreasable 280TS Only 280TS Regreasable Regreasable Regreasable
Mounting Holes 4 4 8 8 8
Mounting Options
Nameplate Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel
NEMA Design A or B B B B B
200/400V 50Hz 1.0SF
Other 1.25SF at 50ºC 200/400V 50Hz 1.0SF
Amb 4P - 150HP iii
Paint Color Gray Gray Gray Gray Gray
Paint Type Alkyd lacquer Lacquer
Part Winding Start 7.5HP: Y Start/³ Run up to 7.5HP - 286T No No No

Product Landscape
Rotatable 90º 90º 90º 90º 90º
T Shaft - Rubber DE, TS
Shaft Slinger Yes, 440 Yes Yes Yes
Shaft - Metal both ends
Temp. Rise 90ºC @ 1.15SF 90ºC @ 1.15SF 80ºC @ 1.0 S.F. 80ºC @ 1.0 S.F. 115ºC @ 1.5SF
Test Method IEEE 112 IEEE 112 IEEE 112 IEEE 112 IEEE 112
Variable Torque 10 : 1 10 : 1 10 : 1 10 : 1 10 : 1
Varnish Type 2 Dip and Bake 2 Dip and Bake VPI VPI VPI
143-405: .001 in max,
Vibration NEMA MG1 Standard, 0.11 in/sec max 0.11 in/sec max 0.11 in/sec max
444-449: .0012 in max
Warranty 12/18 months 12/18 months 12/18 months 12/18 months 12/18 months

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Product Landscape

Feature Value Line Epact XP A$D

Frame Size 140-365 140-180 210-250 280-320
Agency Approvals UL, CSA UL UL UL
Altitude 3300 @ 40ºC 3300 @ 40ºC 3300 @ 40ºC 3300 @ 40ºC
Ambient 40 to -15ºC 40 to -40ºC 40 to -40ºC 40 to -40ºC
Bearing Cap Gasketed No
Bearing Caps No DE DE DE
Direct Coupled: 40,000 Direct Coupled: 130,000 Direct Coupled: 130,000 Direct Coupled: 130,000
Bearing Life (hrs.)
Belted: 20,000 Belted: 26,280 Belted: 26,280 Belted: 26,280
140-280T - Shielded
Bearing Type Shielded Shielded Shielded
280TS, 320-365 - Open
Conduit Box Cast Iron Cast Iron Cast Iron Cast Iron
Constant Torque Infinity:1 Infinity:1 Infinity:1
Efficiency EPAct N/A N/A N/A
Endshield Mat’l Cast Iron Cast Iron Cast Iron Cast Iron
External Fan Non-Sparking Non-Sparking Non-Sparking Non-Sparking
Fan Cover Steel Plate Cast Iron Cast Iron Cast Iron
Frame Mat’l Cast Iron Cast Iron Cast Iron Cast Iron
Grease Lithium Polyurea Polyurea Polyurea
Grounding Term. Bolt in conduit box In Conduit Box In Conduit Box In Conduit Box
Hardware Grade ISO 4.8 Grade 5 Grade 5 Grade 5
Hardware Type Metric SAE SAE SAE
Insulation Type F GEGARD2000™ F GEGARD2000™ F GEGARD2000™ F
140 frame - None
Lifting Means 4 Lugs 4 Lugs 4 Lugs
All others - Eyebolt
280TS, 320-360 - Yes
Lubrication Regreasable Regreasable Regreasable
All Others - No
Mounting Holes 4 8 8 8
Mounting Options F1, F2 F1, F2 F1, F2
Nameplate Stainless Steel Stainless Steel Stainless Steel Stainless Steel
NEMA Design B A A A
Paint Color Gray Gray Gray Gray
Paint Type Enamel Epoxyester Epoxyester Epoxyester
iv Part Winding Start Y Start/³ Run No No No
Rotatable 90º 90º 90º 90º
Shaft Slinger Yes Yes Yes Yes
Temp. Rise 80ºC @ 1.0SF
Product Landscape

Test Method IEEE 112 IEEE 112 IEEE 112 IEEE 112
Variable Torque Infinity:1 Infinity:1 Infinity:1
Varnish Type 2 Dip and Bake Trickle Treat Trickle Treat Trickle Treat
Vibration 0.055 in/sec 0.055 in/sec 0.055 in/sec
Warranty 12/18 months 12/18 months 12/18 months 12/18 months

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Product Landscape

Feature Energy $aver® ODP Energy $aver® TEFC

Frame Size 140-280 320-440 140-320 360-449
UL - Component and Insulation System UL - Component and Insulation System
Agency Approvals UL, CSA UL, CSA
Recognition, CSA - Motors and C-390 Recognition, CSA - Motors and C-390
Altitude 3300 ft @ 40ºC 3300 ft @ 40ºC 3300 ft 3300 ft
Ambient 40 to -20ºC 40 to -20ºC 40 (degree symbol) C 40 (degree symbol) C
Bearing Cap Gasketed No No No No
>320 inner cap
Bearing Caps No None None
440T external cap only
Direct Coupled: 65,000 Direct Coupled: 65,000 Direct Coupled: 65,000 hrs, Belted: Direct Coupled: 65,000 hrs, Belted:
Bearing Life (hrs.)
Belted: 26,280 Belted: 26,280 25,000 hrs 25,000 hrs
Bearing Type Shielded Open Ball Sealed Ball Open
Conduit Box Stamped Steel Stamped Steel Cast Iron Cast Iron
Constant Torque 4:1 4:1 4:1 4:1
Efficiency NEMA Premium NEMA Premium Nema Premium® 2 band min Nema Premium® 2 band min
End Shield Mat’l Cast Iron Cast Iron Cast Iron Cast Iron
External Fan N/A N/A Non-Sparking Non-Sparking
Fan Cover N/A N/A Cast Iron Cast Iron
Frame Mat’l Cast Iron Cast Iron Cast Iron Cast Iron
Grease Lithium Polyurea Lithium (320 Polyurea) Polyurea
Grounding Term Bolt in Cond Box Bolt in Cond Box In Conduit Box In Conduit Box
<250 ISO 4.6
Hardware Grade ISO 8.8 Grade 5 ISO 8.8
Other ISO 8.8
Hardware Type Metric Metric Metric SAE
Insulation Type GEGARD1800™ F GEGARD1800™ F GEGARD1800™ F GEGARD1800™ F
140 Frame: None
Lifting Means Eyebolt eyebolt 4 pt cast in lifting lugs
All other frames: Eyebolt
Lubrication None Regreasable No (320 Yes) Regreasable
Mounting Holes 4 4 1 per foot 2 per foot
All Frames: F1, F2, W1, All frames: F1, F2
Mounting Options F1, modifiable to F2 F1, modifiable to F2
W2, W3, W4, C1, C2 320T-445T: W1,W2,W3,W4
Nameplate Stainless Steel Stainless Steel Stainless Steel Stainless Steel
NEMA Design A or B A or B A or B B
Other 200/400V, 50 Hz.1.OSF 200/400V, 50 Hz.1.OSF
v
Paint Color Buff Buff Buff Buff
Paint Type Polyurethane Polyurethane Alkyd Epoxyester
>100 Hp direct online
Part Winding Start Direct online No No
with Y Start/³ Run

Product Landscape
Rotatable 90º 90º 90 (degree symbol) 90 (degree symbol)
Shaft Slinger No No Steel Reinforced Neoprene Steel Reinforced Neoprene
Temp Rise 80ºC @ 1.0 SF 80ºC @ 1.0 SF 80 (degree symbol) C @ 1.0 SF 80 (degree symbol) C @ 1.0 SF
Tests IEEE 112 IEEE 112 NEMA Routine, IEEE 112-B NEMA Routine, IEEE 112-B
Variable Torque 20:1 20:1 10:1 10:1
Varinsh Type 2 Dip and Bake 2 Dip and Bake 2 Dip and Bake Trickle Treat
Vibration 0.15 in/sec 0.15 in/sec 0.08 in/sec 0.08 in/sec
Warranty 24/30 months 24/30 months 36/42 months 36/42 months

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Product Landscape

Feature Ultra Ultra 841 Ultra 661

Frame Size 140-449 140-449 143-365
Agency Approvals UL,CSA, CE UL,CSA, CE UL, CSA, CE
Altitude 3300 ft @ 40ºC 3300 ft @ 40ºC 3300 ft @ 40ºC
Ambient 40 to -40ºC 40 to -25ºC 40 to -25ºC
Bearing Cap Gasketed Yes Yes Yes
Bearing Caps Yes Yes Yes
Direct Coupled: 130,000 Direct Coupled: 130,000
Bearing Life (hrs.) Belted: 40,000
Belted: 26,280 Belted: 26,280
Bearing Type Single Shielded Single Shielded Roller Bearings
Conduit Box Cast Iron Cast Iron Cast Iron
Constant Torque 20:1 (Exceptions Pg. iii) 20:1 (Exceptions Pg. iii)
Efficiency NEMA Premium NEMA Premium NEMA Premium
Endshield Mat’l Cast Iron Cast Iron Cast Iron
External Fan Non-Sparking Non-Sparking Non-Sparking
Fan Cover Cast Iron Cast Iron Cast Iron
Frame Mat’l Cast Iron Cast Iron Cast Iron
Grease Polyurea Polyurea Polyurea
Bolt in Conduit Box Bolt in Conduit Box
Grounding Term. Bolt in Conduit Box
and Post On Frame and Post On Frame
Hardware Grade Grade 5 Grade 5 Grade 5
Hardware Type SAE SAE SAE
GEGARD2400™ Class F, GEGARD2400™ Class F, GEGARD2400™ Class F,
Insulation Type
Class H (320 and larger) Class H (320 and larger) Class H (320 and larger)
Lifting Means 4 Lugs 4 Lugs 4 Lugs
Lubrication Regreasable Regreasable Regreasable
Mounting Holes 8 8 8
Mounting Options F1, F2 F1, F2 W8, W6
Nameplate Stainless Steel Stainless Steel Stainless Steel
NEMA Design B B B
Paint Color Buff Buff Buff
Paint Type Epoxyester Epoxyester Epoxyester
vi Part Winding Start No No No
Rotatable 90º 90º 90º
Shaft Slinger Yes 2 Inpro Seals 2 Inpro Seals
Temp. Rise 80ºC @ 1.0 S.F. 80ºC @ 1.0 S.F. 80ºC @ 1.0 S.F
Product Landscape

Test Method IEEE 112 IEEE 112 IEEE 112

Variable Torque Infinity:1 Infinity:1 Infinity:1
Varnish Type Trickle Treat Trickle Treat Trickle Treat
Vibration 0.04 in/sec. 0.04 in/sec. 0.0004 in/sec.
Warranty 36/42 months 60/66 months 60/66 months

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Inverter Duty Capabilities

Variable Speed Capabilities for Stock Product

230, 460, 575 Volt

Variable Torque Constant Torque Insulation
Product Frame Comments:
Speed Range Speed Range DV/DT Voltage
NEMA Premium Design
X$D Ultra 140-449T 0 - 60 Hz. ** 3 - 60 Hz. ***GEGARD2400™ 2 pole design 15-60Hz CT spd range.
20HP (4 and 6pole) 10:1
***2400 volt 30HP (4 pole) 6:1
250HP (6 pole) 6:1
Ultra 841 140-449T 0 - 60 Hz. ** 3 - 60 Hz. ***GEGARD2400™ 2 pole design 15-60Hz CT spd range.
20HP (4 and 6pole) 10:1
***2400 volt 30HP (4 pole) 6:1
250HP (6 pole) 6:1
Ultra 661 140-365T 0 - 60 Hz. N/A ***GEGARD2400™
***2400 volt
Ultra Div II 140-449T 0 - 60 Hz. Refer to Factory ***GEGARD2400™
***2400 volt
Energy $aver
TEFC-SD 140-449 6 - 60 Hz. 15 - 60 Hz. GEGARD1800™
1800 volt
Open Dripproof 140-449T 3 - 60 Hz. 15 - 60 Hz. GEGARD1800™
1800 volt
EPAct Design
Value Line - TEFC 140-449T 0 - 60 Hz. 15 - 60 Hz GEGARD1800™
1800 volt
Value Line - ODP 140-449T 0 - 60 Hz. 15 - 60 Hz. GEGARD1800™
1800 volt
Definite Purpose Design
A$D 140-449T 0 - 60 Hz. 0 - 60 Hz. 2000 volt
A$D Ultra 140-449T 0 - 60 Hz. 0 - 60 Hz. GEGARD2800™
2800 volt
Value Line - VHS 140-449T * - 60 Hz. N/A Meets NEMA MG1-31
vii
* Min Speed is 600RPM
** Note Constant Torque Speed Range
*** 2400 volt system for 320 frame and large. All other frames GEGARD2000, 2000 Volt system

Inverter Duty Capabilities

Application Information
1.0 SF
40 degree C amb
3300 ft altitude
Contact GE Motors technical support for more information or specific application data.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

viii

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Open Dripproof
Standard Features
1.1

Value Line™ ODP

HP Range 1-400
Poles 2,4,6
Voltage 200, 230/460, 460, 575
Efficiency EPAct through 200 HP
Frequency 60
NEMA Design A or B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 143-405: .001 in max, 444-449: .0012 in max
Bearing Caps 284TS-286TS and 324-449
Bearing Protection Shaft Slinger on 444-449
Bearing Type Ball, 143T-286T Sealed 284TS-286TS and 324-449 Open
Conduit Box Stamped Steel, rotatable
End Shield Cast Iron
Fasteners Metric, ISO 8.8
Frame Material Cast Iron
Frame Size 143-449
Grease Grease: 143T-286T: Lithium 284TS-286TS and 324-449: Polyurea
Ground Bronze Bolt in Conduit Box
Insulation Class F
Insulation System GEGARD1800™ Non-Hygroscopic, Anti-Fungus, meets NEMA MG1-31
Inverter Capabilities Variable Torque 10:1, Constant Torque 4:1
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 25,000 hrs
Lifting Means 143-145: None, All others: Eye Bolt
Mounting F1, modifiable to F2
Mounting Holes 1 per foot
Nameplate Stainless Steel
Paint Gray, Polyurethane
Relubrication 284TS-286TS and 324-449
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise Class B Rise at 1.15 SF
Tests NEMA Routine, IEEE 112
Time Rating Continuous
Warranty 12 months from date of purchase or 18 months from date of shipment,
whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Open Dripproof
Pricing
1.2
Volts: 200, 230/460, 460, 575
HP: 1-400
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
Value Line™ ODP

1 1800 230/460 143T 3.1/1.6 82.5 S2802 $220 G4-7DEZ Y 49 10.65 29, 105
1 1800 575 143T 1.3 82.5 S2801 $220 G4-7DEZ N 49 10.65 134
1.5 1800 230/460 145T 4.4/2.2 84.0 S2806 $245 G4-7DEZ Y 57 11.65 29, 105
1.5 1800 575 145T 1.8 84.0 S2805 $245 G4-7DEZ N 57 11.65 134
1.5 1200 230/460 182T 4.6/2.3 84.0 S2501 $315 G4-7DEZ Y 88 12.80 29, 105
2 1800 230/460 145T 5.8/2.9 84.0 S2808 $260 G4-7DEZ Y 59 11.65 29, 105
2 1800 575 145T 2.3 84.0 S2807 $260 G4-7DEZ Y 59 11.65
2 1200 230/460 184T 6.2/3.1 85.5 S2502 $332 G4-7DEZ Y 97 13.80 29, 105
3 3600 230/460 145T 7.28/3.64 84.0 S4804 $332 G4-7DEZ Y 52 11.53 6, 29, 105, 107
3 3600 230/460 145T 7.4/3.7 84.0 S2804 $332 G4-7DEZ Y 62 11.65 29, 105, 134
3 3600 575 145T 3.0 84.0 S2803 $332 G4-7DEZ N 62 11.65
3 1800 200 182T 9.0 86.5 S2506 $287 G4-7DEZ Y 81 12.80
3 1800 230/460 182T 7.8/3.9 86.5 S4504 $288 G4-7DEZ Y 91 13.71 29, 105, 107
3 1800 230/460 182T 7.8/3.9 86.5 S2504 $288 G4-7DEZ Y 81 12.80 29, 105
3 1800 575 182T 3.2 86.5 S2505 $287 G4-7DEZ Y 81 12.80
3 1200 230/460 213T 8.6/4.3 86.5 S2507 $450 G4-7DEZ Y 132 15.68 29, 105
3 1200 575 213T 3.5 86.5 S2508 $450 G4-7DEZ Y 132 15.68
5 3600 230/460 182T 11.5/5.77 85.5 S4503 $403 G4-7DEZ Y 85 13.71 6, 29, 105, 107
5 3600 230/460 182T 12.2/6.1 85.5 S2503 $403 G4-7DEZ Y 88 12.80 29, 105, 134
5 3600 575 182T 4.9 85.5 S2552 $402 G4-7DEZ Y 88 12.80
5 1800 200 184T 14.4 87.5 S2513 $348 G4-7DEZ Y 99 13.80
5 1800 230/460 184T 12.8/6.4 87.5 S4511 $348 G4-7DEZ Y 93 14.71 29, 105, 107
5 1800 230/460 184T 12.6/6.3 87.5 S2511 $348 G4-7DEZ Y 99 13.80 29, 105, 134
5 1800 575 184T 5.0 87.5 S2512 $348 G4-7DEZ Y 99 13.80
5 1200 230/460 215T 14.0/7.0 87.5 S2514 $620 G4-7DEZ Y 158 17.20 29, 105
5 1200 575 215T 5.6 87.5 S2515 $620 G4-7DEZ Y 158 17.20
7.5 3600 230/460 184T 17.4/8.7 87.5 S4509 $480 G4-7DEZ Y 93 14.71 6, 29, 105, 107
7.5 3600 230/460 184T 18.0/9.0 87.5 S2509 $480 G4-7DEZ Y 101 13.80 6, 29, 105, 107, 134
7.5 3600 575 184T 7.2 87.5 S2510 $480 G4-7DEZ Y 101 13.80 6, 134
7.5 1800 200 213T 21.4 88.5 S2520 $475 G4-7DEZ Y 152 15.68
7.5 1800 230/460 213T 18.8/9.4 88.5 S4518 $475 G4-7DEZ Y 137 17.47 29, 105, 107
7.5 1800 230/460 213T 18.6/9.3 88.5 S2518 $475 G4-7DEZ Y 152 15.68 6, 29, 105, 107, 134
7.5 1800 575 213T 7.5 88.5 S2519 $475 G4-7DEZ Y 152 15.68 6
7.5 1200 230/460 254T 19.8/9.9 88.5 S2521 $790 G4-7DEZ Y 211 20.50 29, 105, 106
7.5 1200 575 254T 7.9 88.5 S2522 $790 G4-7DEZ Y 211 20.50
10 3600 230/460 213T 24.4/12.2 88.5 S4516 $630 G4-7DEZ Y 133 17.47 6, 29, 105, 107
10 3600 230/460 213T 24.0/12.0 88.5 S2516 $630 G4-7DEZ Y 156 15.68 29, 105, 107, 134
10 3600 575 213T 9.7 88.5 S2517 $630 G4-7DEZ Y 156 15.68
10 1800 200 215T 27.5 89.5 S2527 $590 G4-7DEZ Y 180 17.20
10 1800 230/460 215T 24.6/12.3 89.5 S4525 $590 G4-7DEZ Y 163 19.04 29, 105, 107
10 1800 230/460 215T 23.8/11.9 89.5 S2525 $590 G4-7DEZ Y 180 17.20 6, 29, 105, 107
10 1800 575 215T 9.5 89.5 S2526 $590 G4-7DEZ Y 180 17.20 6
10 1200 230/460 256T 25.8/12.9 90.2 S2528 $945 G4-7DEZ Y 260 22.20 6, 29, 105, 107
10 1200 575 256T 10.4 90.2 S2529 $945 G4-7DEZ N 260 22.20 6
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
106 Usable on 400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
134 Discontinued when stock is depleted. Reference S45XX or S55XX for new catalog number

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Open Dripproof
Pricing cont.
1.3
Volts: 200, 230/460, 460, 575
HP: 1-400
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes

Value Line™ ODP

15 3600 230/460 215T 36.0/18.0 89.5 S4523 $807 G4-7DEZ Y 160 19.04 6, 29, 105, 107
15 3600 230/460 215T 36.0/18.0 89.5 S2523 $807 G4-7DEZ Y 180 17.20 29, 105, 107, 134
15 3600 575 215T 14.4 89.5 S2524 $806 G4-7DEZ Y 180 17.20
15 1800 200 254T 40.3 91.0 S2534 $815 G4-7DEZ N 246 20.50
15 1800 230/460 254T 35.0/17.5 91.0 S4532 $815 G4-7DEZ Y 240 20.45 29, 105, 107
15 1800 230/460 254T 35.2/17.6 91.0 S2532 $815 G4-7DEZ Y 246 20.50 29, 105, 107
15 1800 575 254T 14.1 91.0 S2533 $815 G4-7DEZ Y 246 20.50
15 1200 230/460 284T 38.2/19.1 90.2 S2535 $1,285 G4-7DEZ N 343 22.90 29, 105, 107
15 1200 575 284T 15.3 90.2 S2536 $1,285 G4-7DEZ N 343 22.90
20 3600 230/460 254T 45.9/23.0 90.2 S4530 $971 G4-7DEZ Y 240 20.45 6, 29, 105, 107
20 3600 230/460 254T 45.4/22.7 90.2 S2530 $971 G4-7DEZ Y 233 20.50 6, 29, 105, 107, 134
20 3600 575 254T 18.2 90.2 S2531 $970 G4-7DEZ Y 233 20.50 6
20 1800 200 256T 53.2 91.0 S2541 $1,033 G4-7DEZ N 277 22.20
20 1800 230/460 256T 47.6/23.8 91.0 S4539 $1,033 G4-7DEZ Y 307 22.19 29, 105, 107
20 1800 230/460 256T 46.2/23.1 91.0 S2539 $1,033 G4-7DEZ Y 277 22.20 29, 105, 107, 134
20 1800 575 256T 18.6 91.0 S2540 $1,033 G4-7DEZ Y 277 22.20
20 1200 230/460 286T 50.0/25.0 91.0 S2542 $1,625 G4-7DEZ N 392 24.38 6, 29, 105, 107
25 3600 230/460 256T 55.8/27.9 91.0 S4537 $1,186 G4-7DEZ Y 307 22.19 6, 29, 105, 107
25 3600 230/460 256T 56.0/28.0 91.0 S2537 $1,186 G4-7DEZ Y 282 22.20 6, 29, 105, 107, 134
25 3600 575 256T 22.4 91.0 S2538 $1,185 G4-7DEZ Y 282 22.20 6
25 1800 230/460 284T 59.4/29.7 91.7 S4544 $1,155 G4-7DEZ Y 370 23.43 29, 105, 107
25 1800 230/460 284T 60.0/30.0 91.7 S2544 $1,155 G4-7DEZ Y 352 22.90 29, 105, 107, 134
25 1800 575 284T 24.0 91.7 S2545 $1,155 G4-7DEZ Y 352 22.90
25 1200 230/460 324T 62.6/31.3 91.7 S3502 $1,700 G4-7DEZ N 544 26.60 6, 29, 105, 107
25 1200 575 324T 24.4 91.7 S3501 $1,700 G4-7DEZ N 529 26.60 6
30 3600 230/460 284TS 67.8/33.9 91.0 S4543 $1,396 G4-7DEZ N 390 22.06 6, 29, 105, 107
30 3600 230/460 284TS 67.8/33.9 91.0 S2543 $1,396 G4-7DEZ N 370 22.60 134
30 1800 230/460 286T 69.8/34.9 92.4 S4549 $1,325 G4-7DEZ Y 400 24.93 29, 105, 107
30 1800 230/460 286T 71.2/35.6 92.4 S2549 $1,325 G4-7DEZ Y 407 24.38 6, 134
30 1800 575 286T 28.5 92.4 S2550 $1,325 G4-7DEZ N 407 24.38 6
30 1200 230/460 326T 72.8/36.4 92.4 S3504 $1,950 G4-7DEZ N 573 28.10 6, 29, 105, 107
30 1200 575 326T 29.5 92.4 S3503 $1,950 G4-7DEZ N 573 28.10 6
40 3600 230/460 286TS 89.2/44.6 91.7 S4547 $1,791 G4-7DEZ Y 410 23.57 6, 29, 105, 107
40 3600 230/460 286TS 89.0/44.5 91.7 S2547 $1,791 G4-7DEZ Y 440 24.10 6, 134
40 1800 200 324T 106.0 93.0 S3507 $1,686 G4-7DEZ N 542 26.60 6
40 1800 230/460 324TS 95.6/47.8 93.0 S5567 $1,687 G4-7DEZ Y 606 24.55 29, 105, 107
40 1800 230/460 324TS 91.5/45.8 93.0 S3567 $1,687 G4-7DEZ Y 542 25.10 6, 29, 105, 107, 134
40 1800 230/460 324T 95.6/47.8 93.0 S5506 $1,687 G4-7DEZ Y 580 26.05 29, 105, 107
40 1800 230/460 324T 91.5/45.8 93.0 S3506 $1,687 G4-7DEZ Y 542 26.60 6, 29, 105, 107, 134
40 1800 575 324T 36.6 93.0 S3505 $1,686 G4-7DEZ Y 542 26.60 6
40 1200 460 364T 47.4 93.0 S3509 $3,000 G4-7DEZ Y 726 28.97 106, 107
40 1200 575 364T 37.9 93.0 S3508 $3,000 G4-7DEZ Y 726 28.97
Notes:
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
106 Usable on 400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
134 Discontinued when stock is depleted. Reference S45XX or S55XX for new catalog number

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Open Dripproof
Pricing cont.
1.4
Volts: 230/460, 460, 575
HP: 1-400
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
Value Line™ ODP

50 3600 230/460 324TS 118.0/59.0 92.4 S5511 $2,104 G4-7DEZ Y 606 24.55 6, 29, 105, 107
50 3600 230/460 324TS 118.0/59.0 92.4 S3511 $2,104 G4-7DEZ Y 535 25.10 6, 29, 105, 107, 134
50 3600 575 324TS 47.2 92.4 S3510 $2,103 G4-7DEZ Y 535 25.10 6
50 1800 230/460 326TS 120.0/60.2 93.0 S5569 $1,965 G4-7DEZ Y 692 26.04 29, 105, 107
50 1800 230/460 326TS 114.0/57.0 93.0 S3569 $1,965 G4-7DEZ Y 610 26.60 6, 29, 105, 107, 134
50 1800 230/460 326T 120.0/60.2 93.0 S5513 $1,965 G4-7DEZ Y 639 27.54 29, 105, 107
50 1800 230/460 326T 114.0/57.0 93.0 S3513 $1,965 G4-7DEZ Y 610 28.10 6, 29, 105, 107, 134
50 1800 575 326T 45.6 93.0 S3512 $1,965 G4-7DEZ Y 610 28.10 6
50 1200 460 365T 59.0 93.0 S3515 $3,455 G4-7DEZ Y 803 29.95 106, 107
50 1200 575 365T 47.2 93.0 S3514 $3,455 G4-7DEZ Y 803 29.95
60 3600 230/460 326TS 147.4/73.7 93.0 S5517 $2,730 G4-7DEZ Y 692 26.04 29, 105, 107
60 3600 230/460 326TS 139.0/69.5 93.0 S3517 $2,730 G4-7DEZ Y 603 26.60 6, 29, 105, 107, 134
60 3600 575 326TS 55.6 93.0 S3516 $2,730 G4-7DEZ Y 603 26.60 6
60 1800 230/460 364TS 148.0/73.9 93.6 S5570 $2,780 G4-7DEZ Y 686 27.00 29, 105, 107
60 1800 230/460 364TS 144.0/72.0 93.6 S3570 $2,780 G4-7DEZ Y 719 26.84 6, 29, 105, 107, 134
60 1800 230/460 364T 148.0/73.9 93.6 S5519 $2,780 G4-7DEZ Y 700 29.13 29, 105, 107
60 1800 230/460 364T 144.0/72.0 93.6 S3519 $2,780 G4-7DEZ Y 719 28.97 6, 29, 105, 107, 134
60 1800 575 364T 58.0 93.6 S3518 $2,780 G4-7DEZ Y 719 28.97 6
60 1200 460 404T 69.4 93.6 S3521 $3,895 G4-7DEZ Y 970 32.83 6, 106, 107
60 1200 575 404T 55.5 93.6 S3520 $3,895 G4-7DEZ Y 970 32.83 6
75 3600 230/460 364TS 167.2/83.6 93.0 S5523 $3,800 G4-7DEZ Y 686 27.00 29, 105, 107
75 3600 230/460 364TS 167.0/83.5 93.0 S3523 $3,800 G4-7DEZ Y 695 26.84 29, 105, 107, 134
75 3600 575 364TS 66.8 93.0 S3522 $3,800 G4-7DEZ Y 695 26.84
75 1800 230/460 365TS 186.0/92.8 94.1 S5571 $3,200 G4-7DEZ Y 812 28.00 29, 105, 107
75 1800 230/460 365TS 180.0/90.0 94.1 S3571 $3,200 G4-7DEZ Y 796 27.82 6, 29, 105, 107, 134
75 1800 230/460 365T 186/92.8 94.1 S5525 $3,200 G4-7DEZ Y 838 30.13 29, 105, 107
75 1800 230/460 365T 180.0/90.0 94.1 S3525 $3,200 G4-7DEZ Y 796 29.95 6, 29, 105, 107
75 1800 575 365T 72.0 94.1 S3524 $3,200 G4-7DEZ N 796 29.95 6
75 1200 460 405T 86.7 93.6 S3527 $4,930 G4-7DEZ Y 1105 34.33 6, 106, 107
75 1200 575 405T 69.4 93.6 S3526 $4,930 G4-7DEZ Y 1105 34.33 6
100 3600 230/460 365TS 237.4/118.7 93.0 S5529 $4,950 G4-7DEZ Y 812 28.00 29, 105, 107
100 3600 230/460 365TS 222.0/111.0 93.0 S3529 $4,950 G4-7DEZ Y 757 27.82 6, 29, 105, 107, 134
100 3600 575 365TS 89.5 93.0 S3528 $4,950 G4-7DEZ Y 757 27.82 6
100 1800 230/460 404TS 233.0/116.0 94.1 S5572 $4,200 G4-7DEZ Y 890 30.10 29, 105, 107
100 1800 230/460 404TS 237.0/118.0 94.1 S3572 $4,200 G4-7DEZ Y 981 29.83 6, 29, 105, 107, 134
100 1800 230/460 404T 233.0/116.0 94.1 S5531 $4,200 G4-7DEZ Y 870 33.10 29, 105, 107
100 1800 230/460 404T 237.0/118.0 94.1 S3531 $4,200 G4-7DEZ Y 981 32.83 6, 29, 105, 107, 134
100 1800 575 404T 94.4 94.1 S3530 $4,200 G4-7DEZ Y 981 32.83 6
100 1200 460 444T 117.0 94.1 S3533 $6,215 G4-7DEZ Y 1166 38.30 6, 106, 107
100 1200 575 444T 94.2 94.1 S3532 $6,215 G4-7DEZ Y 1166 38.30 6
Notes:
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
106 Usable on 400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
134 Discontinued when stock is depleted. Reference S45XX or S55XX for new catalog number

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Open Dripproof
Pricing cont.
1.5
Volts: 230/460, 460, 575
HP: 1-400
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes

Value Line™ ODP

125 3600 460 404TS 136.0 93.6 S5535 $6,200 G4-7DEZ Y 890 30.10 106, 107
125 3600 460 404TS 136.0 93.6 S3535 $6,200 G4-7DEZ Y 931 29.83 106, 107, 134
125 3600 575 404TS 109.0 93.6 S3534 $6,200 G4-7DEZ Y 931 29.83
125 1800 460 405TS 142.0 94.5 S5573 $5,125 G4-7DEZ Y 1150 31.60 106, 107
125 1800 460 405TS 145.0 94.5 S3573 $5,125 G4-7DEZ Y 1094 31.33 6, 106, 107, 134
125 1800 460 405T 142.0 94.5 S5537 $5,125 G4-7DEZ Y 960 34.60 106, 107
125 1800 460 405T 145.0 94.5 S3537 $5,125 G4-7DEZ Y 1094 34.33 6, 106, 107, 134
125 1800 575 405T 116.0 94.5 S3536 $5,125 G4-7DEZ Y 1094 34.33 6
125 1200 460 445T 146.0 94.1 S3539 $7,815 G4-7DEZ Y 1276 40.30 6, 106, 107
125 1200 575 445T 122.0 94.1 S3538 $7,815 G4-7DEZ Y 1276 40.30 6
150 3600 460 405TS 174.9 93.6 S5541 $7,600 G4-7DEZ Y 1150 31.60 106, 107
150 3600 460 405TS 165.0 93.6 S3541 $7,600 G4-7DEZ Y 1005 31.33 106, 107, 134
150 3600 575 405TS 130.0 93.6 S3540 $7,600 G4-7DEZ Y 1005 31.33 6
150 1800 460 444TS 171.0 95.0 S5574 $7,485 G4-7DEZ Y 1310 33.95 106, 107
150 1800 460 444TS 171.0 95.0 S3574 $7,485 G4-7DEZ Y 1320 34.35 6, 106, 107, 134
150 1800 460 444T 171.0 95.0 S5543 $7,485 G4-7DEZ Y 1330 37.70 106, 107
150 1800 460 444T 171.0 95.0 S3543 $7,485 G4-7DEZ Y 1320 38.30 6, 106, 107, 134
150 1800 575 444T 137.0 95.0 S3542 $7,485 G4-7DEZ Y 1320 38.30 6
150 1200 460 445T 173.0 94.5 S3545 $9,145 G4-7DEZ Y 1364 40.30 6, 106, 107
150 1200 575 445T 141.0 94.5 S3544 $9,145 G4-7DEZ Y 1364 40.30 6
200 3600 460 444TS 228.0 94.5 S5547 $11,485 G4-7DEZ Y 1310 33.95 106, 107
200 3600 460 444TS 221.0 94.5 S3547 $11,485 G4-7DEZ Y 1150 34.35 6, 106, 107, 134
200 3600 575 444TS 177.0 94.5 S3546 $11,485 G4-7DEZ Y 1150 34.35 6
200 1800 460 445TS 228.0 95.0 S5575 $10,095 G4-7DEZ Y 1480 35.95 106, 107
200 1800 460 445TS 226.0 95.0 S3575 $10,095 G4-7DEZ Y 1430 36.35 6, 106, 107
200 1800 460 445T 228.0 95.0 S5549 $10,095 G4-7DEZ Y 1510 39.70 106, 107
200 1800 460 445T 226.0 95.0 S3549 $10,095 G4-7DEZ Y 1430 40.30 6, 106, 107
200 1800 575 445T 185.0 95.0 S3548 $10,094 G4-7DEZ Y 1430 40.30 6
200 1200 460 447T 233.0 94.5 S3551 $14,550 G4-7DEZ Y 1810 43.95 6, 106, 107
200 1200 575 447T 184.0 94.5 S3550 $14,550 G4-7DEZ Y 1810 43.95 6
250 3600 460 445TS 273.0 94.5 S5553 $14,225 G4-7DEZ Y 1480 35.95 106, 107
250 3600 460 445TS 279.0 94.5 S3553 $14,225 G4-7DEZ Y 1276 36.35 6, 106, 107
250 3600 575 445TS 217.0 94.5 S3552 $14,244 G4-7DEZ Y 1276 36.35 6
250 1800 460 447T 280.0 95.4 S3555 $12,150 G4-7DEZ Y 1760 43.95 6, 106, 107
250 1800 575 447T 227.0 95.4 S3554 $12,150 G4-7DEZ Y 1760 43.95 6
250 1200 460 449T 285.0 95.4 S3557 $16,500 G4-7DEZ Y 2160 48.95 6, 106, 107
250 1200 575 449T 228.0 95.4 S3556 $16,500 G4-7DEZ Y 2160 48.95 6
300 3600 460 445TS 324.0 95.0 S5559 $17,363 G4-7DEZ Y 1480 35.95 106, 107
300 3600 460 445TS 338.0 95.0 S3559 $17,363 G4-7DEZ Y 1320 36.35 6, 106, 107, 134
300 3600 575 445TS 260.0 95.0 S3558 $17,363 G4-7DEZ Y 1320 36.35 6
300 1800 460 449T 335.0 95.4 S3561 $15,985 G4-7DEZ Y 1870 48.95 6, 106, 107
300 1800 575 449T 272.0 95.4 S3560 $15,985 G4-7DEZ Y 1870 48.95 6
350 3600 460 447TS 375.0 95.0 S5563 $19,850 G4-7DEZ N 2100 39.46 106, 107
350 3600 460 447TS 381.0 95.0 S3563 $19,850 G4-7DEZ N 1590 40.20 6, 106, 107, 134
350 3600 575 447TS 305.0 95.0 S3562 $19,850 G4-7DEZ N 1590 40.20 6
400 3600 460 449TS 427.0 95.4 S3565 $20,580 G4-7DEZ N 1760 45.20 6, 106, 107
400 3600 575 449TS 341.0 95.4 S3564 $20,280 G4-7DEZ N 1760 45.20 6
Notes
6 NEMA Design A 106 Usable on 400V, 50Hz at 1.0 service factor
29 Usable on 200 Volts, 60Hz at 1.0 service factor 107 Y-Start/Delta-Run Capable
105 Usable on 200/400V, 50Hz at 1.0 service factor 134 Discontinued when stock is depleted. Reference S45XX or S55XX for new catalog number
Data subject to change without notice. GEP-500T 03/08. www.gemotors.com
 Value Line™
Open Dripproof
NEMA Motor Dimensions
1.6
C

N MIN
Value Line™ ODP

V
KEY LENGTH

2E H HOLE 2F BA

NEMA Key Key Key

Frame D 2E 2F BA H N-W U V Min. Width Thickness Length
143T 3.50 5.50 4.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
145T 3.50 5.50 5.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
182T 4.50 7.50 4.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
284TS 7.00 11.00 9.50 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286TS 7.00 11.00 11.00 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
324TS 8.00 12.50 10.50 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326TS 8.00 12.50 12.00 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
364T 9.00 14.00 11.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365T 9.00 14.00 12.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
404T 10.00 16.00 12.25 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
404TS 10.00 16.00 12.25 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
405T 10.00 16.00 13.75 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
405TS 10.00 16.00 13.75 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
444T 11.00 18.00 14.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
444TS 11.00 18.00 14.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
445T 11.00 18.00 16.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
445TS 11.00 18.00 16.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
447T 11.00 18.00 20.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
447TS 11.00 18.00 20.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
449T 11.00 18.00 25.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
449TS 11.00 18.00 25.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.63 3.00
Notes
“C” dimension is overall length and is shown for each catalog number on rating pages.
All dimensions in inches. All dimensions are nominal. Request factory outlines for exact dimensions.
1. Motor base has two sets of holes at 3.00 and 5.00 inches.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
TEFC and TEFC-SD (where noted)
Standard Features
1.7

Value Line™ TEFC and TEFC-SD

HP Range .75-250
Poles 2, 4, 6
Voltage 200, 230/460, 460, 575
Efficiency EPAct
Frequency 60 Hz
NEMA Design A or B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40°C
Balance/Vibration 143-449: NEMA MG1 Standard
Bearing Cap 284TS-286TS and 324-449
Bearing Protection Shaft Slinger
Bearing Type Ball, 143T-286T Sealed; 284TS-286TS and 324-449 Open
Conduit Box 143-286: Stamped Steel, 324-449: Cast Iron
Drains 2 holes
End Shield Cast Iron
Fasteners 143-286 Metric, 324-449: SAE
Frame Material Cast Iron
Frame Size 143-449 See Severe Duty for higher Horsepower & frame.
Grease 143T-286T: Lithium, 284-286TS and 324-449: Polyurea
Ground In Conduit Box
Inverter Capabilities Variable Torque 10:1, Constant Torque 4:1
Insulation Class F
Insulation System GEGARD1800™ Non-Hygroscopic, Anti-Fungus, meets NEMA MG1-31
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 25,000 hrs
Lifting Means 143-145: None, 182-449: Eyebolt
Mounting F1, modifiable to F2
Mounting Holes 143-286: 1 per foot, 324-449: 2 per foot
Nameplate Stainless Steel
Paint Gray, 143-286: Lacquer, 324-449: Epoxy
Relubrication 284TS-286TS and 324-449
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 143-286: 90°C @ 1.15SF, 324-449: 115°C @ 1.15 SF
Tests NEMA Routine, IEEE 112
Time Rating Continuous
12 months from date of purchase or 18 months from date of shipment,
Warranty
whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
TEFC and TEFC-SD (where noted)
Pricing
1.8
Volts: 200, 230/460, 460, 575
Value Line™ TEFC and TEFC-SD

HP: .75 - 250

HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
0.75 1200 230/460 143T 2.8/1.4 82.5 S212 $315 G4-7TEZ Y 55 12.05 29, 105
1 1800 230/460 143T 3.2/1.6 82.5 S4211 $243 G4-7TEZ Y 50 12.25 29, 105, 107
1 1800 230/460 143T 2.9/1.5 82.5 S211 $243 G4-7TEZ Y 53 12.05 29, 105, 135
1 1800 575 143T 1.2 82.5 S2790 $250 G4-7TEZ Y 53 12.05
1 1200 230/460 145T 3.3/1.7 80.0 S216 $315 G4-7TEZ Y 59 13.05 29, 105
1.5 3600 230/460 143T 4.4/2.2 82.5 S4210 $282 G4-7TEZ Y 50 12.25 29, 105, 107
1.5 3600 230/460 143T 4.0/2.0 82.5 S210 $282 G4-7TEZ Y 53 12.05 29, 105, 135
1.5 1800 230/460 145T 4.4/2.2 84.0 S4214 $262 G4-7TEZ Y 56 13.24 29, 105, 107
1.5 1800 230/460 145T 4.1/2.1 84.0 S214 $262 G4-7TEZ Y 57 13.05 29, 105, 135
1.5 1800 575 145T 1.6 84.0 S2791 $200 G4-7TEZ N 57 13.05
1.5 1200 230/460 182T 5.0/2.5 85.5 S220 $339 G4-7TEZ Y 90 14.40 29, 105
2 3600 230/460 145T 4.9/2.4 84.0 S4202 $321 G4-7TEZ Y 52 13.24 29, 105, 107
2 3600 230/460 145T 5.1/2.6 84.0 S213 $321 G4-7TEZ Y 57 13.05 29, 105
2 1800 230/460 145T 5.4/2.7 84.0 S4215 $282 G4-7TEZ Y 56 13.24 29, 105, 107
2 1800 230/460 145T 5.5/2.8 84.0 S215 $282 G4-7TEZ Y 57 13.05 29, 105, 135
2 1800 575 145T 2.2 84.0 S2793 $290 G4-7TEZ Y 57 13.05
2 1200 230/460 184T 6.4/3.2 86.5 S226 $375 G4-7TEZ Y 101 15.40 29, 105
3 3600 230/460 182T 7.2/3.6 85.5 S4221 $357 G4-7TEZ Y 78 14.59 29, 105, 107
3 3600 230/460 182T 7.2/3.6 85.5 S221 $357 G4-7TEZ Y 90 14.40 29, 105, 135
3 3600 575 182T 2.9 85.5 S2792 $357 G4-7TEZ N 90 14.40
3 1800 200 182T 8.7 87.5 S218 $320 G4-7TEZ N 95 14.40 6, 135
3 1800 230/460 182T 7.8/3.9 87.5 S4219 $320 G4-7TEZ Y 80 14.59 29, 105, 107
3 1800 230/460 182T 7.6/3.8 87.5 S219 $320 G4-7TEZ Y 95 14.40 6, 29, 105, 135
3 1800 575 182T 3.1 87.5 S217 $320 G4-7TEZ Y 95 14.40 135
3 1200 230/460 213T 8.8/4.4 87.5 S234 $497 G4-7TEZ Y 139 17.78 29, 105
3 1200 575 213T 3.5 87.5 S233 $497 G4-7TEZ Y 139 17.78
5 3600 230/460 184T 11.8/5.9 87.5 S4227 $442 G4-7TEZ Y 92 15.57 29, 105, 107
5 3600 230/460 184T 11.8/5.9 87.5 S227 $442 G4-7TEZ Y 106 15.40 6, 29, 105, 135
5 3600 575 184T 4.7 87.5 S222 $442 G4-7TEZ Y 106 15.40
5 1800 200 184T 14.3 87.5 S224 $380 G4-7TEZ N 114 15.40 6
5 1800 230/460 184T 12.8/6.4 87.5 S4225 $380 G4-7TEZ Y 95 15.57 29, 105, 107
5 1800 230/460 184T 12.4/6.2 87.5 S225 $380 G4-7TEZ Y 115 15.40 6, 29, 105, 135
5 1800 575 184T 5.0 87.5 S223 $380 G4-7TEZ Y 114 15.40
5 1200 230/460 215T 13.4/6.7 87.5 S241 $716 G4-7TEZ Y 165 19.28 29, 105, 135
5 1200 575 215T 5.5 87.5 S240 $716 G4-7TEZ Y 165 19.28
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
135 Discontinued when stock is depleted. Reference S42XX for new catalog number

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
TEFC and TEFC-SD (where noted)
Pricing cont.
1.9
Volts: 200, 230/460, 460, 575

Value Line™ TEFC and TEFC-SD

HP: .75 - 250
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
7.5 3600 230/460 213T 18.2/9.1 88.5 S4229 $576 G4-7TEZ Y 138 17.78 29, 105, 107
7.5 3600 230/460 213T 17.8/8.9 88.5 S229 $576 G4-7TEZ Y 156 17.78 6, 29, 105, 107, 135
7.5 3600 575 213T 7.1 88.5 S228 $576 G4-7TEZ Y 156 17.78
7.5 1800 200 213T 20.9 89.5 S232 $510 G4-7TEZ N 167 17.78 6
7.5 1800 230/460 213T 18.4/9.2 89.5 S4231 $510 G4-7TEZ Y 140 17.78 29, 105, 107
7.5 1800 230/460 213T 18.2/9.1 89.5 S231 $510 G4-7TEZ Y 167 17.78 6, 29, 105, 107, 135
7.5 1800 575 213T 7.3 89.5 S230 $510 G4-7TEZ Y 167 17.78
7.5 1200 230/460 254T 19.4/9.7 89.5 S248 $945 G4-7TEZ Y 257 23.08 29, 105, 107, 135
7.5 1200 575 254T 7.7 89.5 S247 $945 G4-7TEZ Y 257 23.80
10 3600 230/460 215T 23.4/11.7 89.5 S4236 $677 G4-7TEZ Y 146 19.27 29, 105, 107
10 3600 230/460 215T 23.2/11.6 89.5 S236 $677 G4-7TEZ Y 183 19.28 29, 105, 107, 135
10 3600 575 215T 9.3 89.5 S235 $677 G4-7TEZ Y 183 19.28
10 1800 200 215T 27.2 89.5 S239 $630 G4-7TEZ N 189 19.28 6
10 1800 230/460 215T 24.4/12.2 89.5 S4238 $630 G4-7TEZ Y 152 19.27 29, 105, 107
10 1800 230/460 215T 23.8/11.9 89.5 S238 $630 G4-7TEZ Y 189 19.28 6, 29, 105, 107, 135
10 1800 575 215T 9.4 89.5 S237 $630 G4-7TEZ Y 189 19.28
10 1200 230/460 256T 25.8/12.9 89.5 S255 $1,174 G4-7TEZ Y 295 24.80 6, 29, 105, 107, 135
10 1200 575 256T 10.3 89.5 S254 $1,174 G4-7TEZ Y 295 24.80
15 3600 230/460 254T 35.2/17.6 90.2 S4243 $888 G4-7TEZ Y 290 23.70 29, 105, 107
15 3600 230/460 254T 33.6/16.8 90.2 S243 $888 G4-7TEZ Y 282 23.08 6, 29, 105, 107, 135
15 3600 575 254T 13.6 90.2 S242 $888 G4-7TEZ Y 282 23.08
15 1800 200 254T 39.7 91.0 S246 $881 G4-7TEZ N 288 23.08 6
15 1800 230/460 254T 36.4/18.2 91.0 S4245 $881 G4-7TEZ Y 260 23.70 29, 105, 107
15 1800 230/460 254T 34.8/17.4 91.0 S245 $881 G4-7TEZ Y 288 23.08 6, 29, 105, 107, 135
15 1800 575 254T 13.9 91.0 S244 $908 G4-7TEZ Y 288 23.08
15 1200 230/460 284T 37.4/18.7 90.2 S261 $1,594 G4-7TEZ Y 414 26.07 6, 29, 105, 107, 135
15 1200 575 284T 15.0 90.2 S260 $1,594 G4-7TEZ Y 414 26.07
20 3600 230/460 256T 45.3/22.7 90.2 S4250 $1,136 G4-7TEZ Y 325 25.40 29, 105, 107
20 3600 230/460 256T 44.4/22.2 90.2 S250 $1,136 G4-7TEZ Y 315 24.80 6, 29, 105, 107, 135
20 3600 575 256T 17.8 90.2 S249 $1,136 G4-7TEZ Y 315 24.80
20 1800 200 256T 66.6 92.4 S253 $1,141 G4-7TEZ N 332 24.80 6
20 1800 230/460 256T 48.2/24.1 91.0 S4252 $1,141 G4-7TEZ Y 290 25.40 29, 105, 107
20 1800 230/460 256T 46.0/23.0 91.0 S252 $1,141 G4-7TEZ Y 332 24.80 6, 29, 105, 107, 135
20 1800 575 256T 18.3 91.0 S251 $1,176 G4-7TEZ Y 332 24.80
20 1200 230/460 286T 50.0/25.0 90.2 S267 $1,881 G4-7TEZ Y 473 27.57 29, 105, 107, 135
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
135 Discontinued when stock is depleted. Reference S42XX for new catalog number

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
TEFC and TEFC-SD (where noted)
Pricing cont.
1.10
Volts: 200, 230/460, 460, 575
Value Line™ TEFC and TEFC-SD

HP: .75 - 250

HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
25 3600 230/460 284TS 57.8/28.9 91.0 S4256 $1,432 G4-7TEZ Y 425 25.33 29, 105, 107
25 3600 230/460 284TS 55.6/27.8 91.0 S256 $1,432 G4-7TEZ Y 418 24.95 29, 105, 107, 135
25 1800 200 284T 79.4 92.4 S259 $1,366 G4-7TEZ N 429 26.07 6
25 1800 230/460 284T 58.8/29.4 92.4 S4258 $1,366 G4-7TEZ Y 430 26.70 29, 105, 107
25 1800 230/460 284T 58.0/29.0 92.4 S258 $1,366 G4-7TEZ Y 429 26.07 6, 29, 105, 107, 135
25 1800 575 284T 23.3 92.4 S257 $1,366 G4-7TEZ Y 429 26.07
25 1200 230/460 324TS 61.2/30.6 91.7 S278 $2,312 G4-7TEZ N 625 31.70
25 1200 230/460 324T 61.2/30.6 91.7 S279 $2,312 G4-7TEZ Y 626 33.30
30 3600 200 286TS 76.3 91.0 S263 $1,666 G4-7TEZ N 455 26.20
30 3600 230/460 286TS 70.0/35.0 91.0 S4262 $1,666 G4-7TEZ Y 465 26.83 29, 105, 107
30 3600 230/460 286TS 66.8/33.4 91.0 S262 $1,666 G4-7TEZ Y 455 26.20 6, 29, 105, 107, 135
30 1800 200 286T 79.4 92.4 S266 $1,547 G4-7TEZ N 475 27.57 6
30 1800 230/460 286T 70.2/35.1 92.4 S4265 $1,547 G4-7TEZ Y 455 28.20 29, 105, 107
30 1800 230/460 286T 69.0/34.5 92.4 S265 $1,547 G4-7TEZ Y 475 27.57 6, 29, 105, 107, 135
30 1800 575 286T 27.6 92.4 S264 $1,547 G4-7TEZ Y 475 27.57
30 1200 230/460 326T 71.6/35.8 91.7 S280 $2,709 G4-7TEZ Y 763 33.30
40 3600 230/460 324TS 90.2/45.1 91.7 S281 $2,144 G4-7TEZ Y 788 31.70
40 3600 230/460 324T 90.2/45.1 91.7 S282 $2,144 G4-7TEZ Y 788 33.30
40 1800 230/460 324T 90.0/45.0 93.0 S283 $2,053 G4-7TEZ Y 776 33.30
40 1800 575 324T 36.5 93.0 S284 $2,053 G4-7TEZ Y 776 31.20
40 1200 230/460 364T 91.8/45.9 93.0 S285 $3,719 G4-7TEZ Y 932 35.00
50 3600 230/460 326TS 111.4/55.7 92.4 S286 $2,774 G4-7TEZ Y 788 31.70
50 3600 230/460 326T 111.4/55.7 92.4 S287 $2,774 G4-7TEZ Y 788 33.30
50 1800 230/460 326TS 111.2/55.6 93.0 S288 $2,521 G4-7TEZ Y 803 31.70
50 1800 230/460 326T 111.2/55.6 93.0 S289 $2,521 G4-7TEZ Y 803 33.30
50 1800 575 326T 46.1 93.0 S290 $2,521 G4-7TEZ Y 803 31.20
50 1200 230/460 365T 114.4/57.2 93.0 S291 $4,337 G4-7TEZ Y 933 35.00
60 3600 230/460 364TS 133.0/66.5 93 S292 $3,751 G4-7TEZ Y 935 33.10
60 1800 230/460 364TS 134.2/67.1 93.6 S293 $3,617 G4-7TEZ Y 928 33.10
60 1800 230/460 364T 134.2/67.1 93.6 S295 $3,617 G4-7TEZ Y 932 35.00
60 1800 575 364T 56.2 93.6 S296 $3,617 G4-7TEZ Y 932 33.50
75 3600 230/460 365TS 165.0/82.5 93.0 S297 $4,581 G4-7TEZ Y 992 33.10
75 1800 230/460 365T 164.0/82.0 94.1 S298 $4,584 G4-7TEZ Y 1001 35.00
75 1800 575 365T 69.1 94.1 S299 $4,584 G4-7TEZ Y 1001 34.50
100 3600 230/460 405TS 222.0/111.0 93.6 S4346 $6,296 G4-7SEZ Y 1259 35.60 111
100 3600 460 405TS 111.0 93.6 S4116 $6,296 G4-7SEZ Y 1259 35.60 111
100 3600 575 405TS 88.8 93.6 S4175 $6,296 G4-7SEZ Y 1259 35.60 111
100 1800 230/460 405TS 218.8/109.4 93.6 S4123 $5,810 G4-7SEZ Y 1299 35.60 111
100 1800 230/460 405T 218.8/109.4 94.5 S4347 $5,810 G4-7SEZ Y 1299 38.60 111
100 1800 460 405T 109.4 94.5 S4117 $5,810 G4-7SEZ Y 1299 38.60 111
100 1800 575 405T 87.5 94.5 S4176 $5,810 G4-7SEZ Y 1299 38.60 111
100 1200 460 444T 113.7 94.1 S4118 $8,400 G4-7SEZ Y 1671 47.10 111
100 1200 575 444T 91.0 94.1 S4177 $8,400 G4-7SEZ Y 1671 47.10 111
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
111 Contains features corresponding to TEFC - Severe Duty
135 Discontinued when stock is depleted. Reference S42XX for new catalog number

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
TEFC and TEFC-SD (where noted)
Pricing cont.
1.11
Volts: 200, 230/460, 460, 575

Value Line™ TEFC and TEFC-SD

HP: .75 - 250
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
125 3600 460 444TS 136.0 94.5 S4334 $8,230 G4-7SEZ Y 1623 42.20 111
125 3600 575 444TS 108.8 94.5 S4178 $8,230 G4-7SEZ Y 1623 42.20 111
125 1800 460 444TS 138.0 94.5 S4348 $7,648 G4-7SEZ Y 1554 42.20 111
125 1800 460 444T 138.0 94.5 S4119 $7,648 G4-7SEZ Y 1554 47.10 111
125 1800 575 444T 110.4 94.5 S4179 $7,648 G4-7SEZ Y 1554 47.10 111
125 1200 460 445T 141.0 94.1 S4120 $9,780 G4-7SEZ N 1775 47.10 111
125 1200 575 445T 112.8 94.1 S4180 $9,780 G4-7SEZ Y 1775 47.10 111
150 3600 460 445TS 164.0 94.5 S4121 $9,886 G4-7SEZ Y 1722 42.20 111
150 3600 575 445TS 131.2 94.5 S4181 $9,886 G4-7SEZ N 1722 42.20 111
150 1800 460 445T 164.0 95.0 S4122 $8,891 G4-7SEZ N 1739 47.10 111
150 1800 460 445TS 164.0 95.0 S4349 $8,891 G4-7SEZ N 1739 42.20 111
150 1800 575 445T 131.2 95.0 S4182 $8,891 G4-7SEZ N 1739 47.10 111
200 3600 460 447TS 218.0 95.0 S4387 $12,506 G4-7SEZ N 2420 50.37 111
200 3600 575 447TS 171.0 95.0 S4384 $12,506 G4-7SEZ N 2560 50.37 111
200 1800 460 447T 232.0 95.0 S4352 $10,814 G4-7SEZ N 2560 54.12 111
200 1800 575 447T 183.0 95.0 S4385 $10,814 G4-7SEZ N 2560 54.12 111
200 1200 460 449T 239.0 95.0 S4351 $14,800 G4-7SEZ N 2730 54.12 111
200 1200 575 449T 192.0 95.0 S4386 $14,800 G4-7SEZ N 2730 54.12 111
250 1800 460 449T 291.0 95.0 S4353 $13,567 G4-7SEZ N 2580 54.12 111
Notes
111 Contains features corresponding to TEFC - Severe Duty

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Totally Enclosed Fan-Cooled
C-Face Pricing
1.12
Volts: 230/460
HP: 1-75
HP RPM Volts Frame Base FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
Value Line™ TEFC

1 1800 230/460 143TC Ftd 3.2/1.6 82.5 S5211 $288 G4-7TECZ Y 50 12.75 29, 105, 107
1 1800 230/460 143TC Ftd 2.9/1.5 82.5 S2211 $288 G4-7TECZ Y 53 12.05 29,105,110,136
1 1800 230/460 143TC NB 2.9/1.5 82.5 S209 $385 G4-7TECZ Y 53 12.47 29,105,110
1 1200 230/460 145TC Ftd 3.3/1.7 80.0 S5216 $378 G4-7TECZ Y 56 13.74 29, 105, 107
1 1200 230/460 145TC Ftd 3.3/1.7 80.0 S2216 $378 G4-7TECZ Y 62 13.05 29,105,110,136
1.5 3600 230/460 143TC Ftd 4.4/2.2 82.5 S5210 $328 G4-7TECZ Y 15 12.75 29, 105, 107
1.5 3600 230/460 143TC Ftd 4.0/2.0 82.5 S2210 $328 G4-7TECZ Y 53 12.05 29,105,110,136
1.5 1800 230/460 145TC Ftd 4.4/2.2 84.0 S5214 $308 G4-7TECZ Y 56 13.74 29, 105, 107
1.5 1800 230/460 145TC Ftd 4.1/2.1 84.0 S2214 $308 G4-7TECZ Y 62 13.05 29,105,110,136
1.5 1800 230/460 145TC NB 4.1/2.1 84.0 S268 $405 G4-7TECZ N 57 13.46 29,105,110
2 3600 230/460 145TC Ftd 4.9/2.4 84.0 S5213 $368 G4-7TECZ Y 52 13.74 29, 105, 107
2 3600 230/460 145TC Ftd 5.1/2.6 84.0 S2213 $368 G4-7TECZ Y 62 13.05 29,105,110,136
2 1800 230/460 145TC Ftd 5.4/2.7 84.0 S5215 $328 G4-7TECZ Y 56 13.74 29, 105, 107
2 1800 230/460 145TC Ftd 5.5/2.8 84.0 S2215 $328 G4-7TECZ Y 62 13.05 29,105,110,136
2 1800 230/460 145TC NB 5.5/2.8 84.0 S269 $425 G4-7TECZ Y 57 13.46 29,105,110
3 3600 230/460 182TC Ftd 7.2/3.6 85.5 S5221 $413 G4-7TECZ Y 78 15.18 29, 105, 107
3 3600 230/460 182TC Ftd 7.2/3.6 85.5 S2221 $413 G4-7TECZ Y 95 14.40 29,105,110,136
3 1800 230/460 182TC Ftd 7.8/3.9 87.5 S5219 $376 G4-7TECZ Y 80 15.18 29, 105, 107
3 1800 230/460 182TC Ftd 7.6/3.8 87.5 S2219 $376 G4-7TECZ Y 95 14.40 6,29,105,110,136
3 1800 230/460 182TC NB 7.6/3.8 87.5 S270 $479 G4-7TECZ Y 95 14.75 6,29,105,110
5 3600 230/460 184TC Ftd 11.8/5.9 87.5 S5227 $498 G4-7TECZ Y 92 16.17 29, 105, 107
5 3600 230/460 184TC Ftd 11.8/5.9 87.5 S2227 $498 G4-7TECZ Y 106 15.40 6,29,105,110,136
5 1800 230/460 184TC Ftd 12.8/6.4 87.5 S5225 $436 G4-7TECZ Y 95 16.17 29, 105, 107
5 1800 230/460 184TC Ftd 12.4/6.2 87.5 S2225 $436 G4-7TECZ Y 114 15.40 6,29,105,110,136
5 1800 230/460 184TC NB 12.4/6.2 87.5 S271 $539 G4-7TECZ Y 114 15.77 6,29,105,110
7.5 3600 230/460 213TC Ftd 18.2/9.1 88.5 S5229 $643 G4-7TECZ Y 138 18.69 29, 105, 107
7.5 3600 230/460 213TC Ftd 17.8/8.9 88.5 S2229 $643 G4-7TECZ Y 156 17.78 6,29,105,107,110,136
7.5 1800 230/460 213TC Ftd 18.4/9.2 89.5 S5231 $577 G4-7TECZ Y 140 18.69 29, 105, 107
7.5 1800 230/460 213TC Ftd 18.2/9.1 89.5 S2231 $577 G4-7TECZ Y 167 17.78 6,29,105,107,110,136
7.5 1800 230/460 213TC NB 18.2/9.1 89.5 S272 $684 G4-7TECZ Y 167 18.09 6,29,105,107,110
10 3600 230/460 215TC Ftd 23.4/11.7 89.5 S5236 $744 G4-7TECZ Y 146 20.18 29, 105, 107
10 3600 230/460 215TC Ftd 23.2/11.6 89.5 S2236 $744 G4-7TECZ Y 183 19.28 29,105,107,110,136
10 1800 230/460 215TC Ftd 24.4/12.2 89.5 S5238 $697 G4-7TECZ Y 152 20.18 29, 105, 107
10 1800 230/460 215TC Ftd 23.8/11.9 89.5 S2238 $697 G4-7TECZ Y 189 19.28 6,29,105,107,110,136
10 1800 230/460 215TC NB 23.8/11.9 89.5 S273 $804 G4-7TECZ Y 189 19.59 6,29,105,107,110
15 3600 230/460 254TC Ftd 35.2/17.6 90.2 S5243 $1,016 G4-7TECZ Y 290 23.95 29, 105, 107
15 3600 230/460 254TC Ftd 33.6/16.8 90.2 S2243 $1,016 G4-7TECZ Y 282 23.43 29,105,107,110,136
15 1800 230/460 254TC Ftd 36.4/18.2 91.0 S5245 $1,009 G4-7TECZ Y 260 23.95 29, 105, 107
15 1800 230/460 254TC Ftd 34.8/17.4 91.0 S2245 $1,009 G4-7TECZ Y 288 23.43 6,29,105,107,110,136
15 1800 230/460 254TC NB 34.8/17.4 91.0 S274 $1,127 G4-7TECZ Y 288 23.60 6,29,105,107,110
20 3600 230/460 256TC Ftd 45.3/22.7 90.2 S5250 $1,272 G4-7TECZ Y 325 25.65 29, 105, 107
20 3600 230/460 256TC Ftd 44.4/22.2 90.2 S2250 $1,272 G4-7TECZ Y 315 25.20 6,29,105,107,110,136
20 1800 230/460 256TC Ftd 48.2/24.1 91.0 S5252 $1,277 G4-7TECZ Y 290 25.65 29, 105, 107
20 1800 230/460 256TC Ftd 46.0/23.0 91.0 S2252 $1,277 G4-7TECZ Y 332 25.20 29,105,107,110,136
20 1800 230/460 256TC NB 46.0/23.0 91.0 S275 $1,395 G4-7TECZ Y 332 25.34 29,105,107,110
Notes
6 NEMA Design A 107 Y-Start/Delta-Run Capable
29 Usable on 200 Volts, 60Hz at 1.0 service factor 110 Non-NEMA BA dimension
105 Usable on 200/400V, 50Hz at 1.0 service factor 136 Discontinued when stock is depleted. Reference S52XX for new catalog number

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Totally Enclosed Fan-Cooled
C-Face Pricing cont.
1.13
Volts: 230/460
HP: 1-75
HP RPM Volts Frame Base FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes

Value Line™ TEFC

25 3600 230/460 284TSC Ftd 57.8/28.9 91.0 S5256 $1,593 G4-7TECZ Y 430 25.53 29,105,107
25 3600 230/460 284TSC Ftd 55.6/27.8 91.0 S2256 $1,593 G4-7TECZ Y 418 25.15 29,105,107,136
25 1800 230/460 284TC Ftd 58.8/29.4 92.4 S5258 $1,570 G4-7TECZ Y 430 26.90 29,105,107
25 1800 230/460 284TC Ftd 58.0/29.0 92.4 S2258 $1,570 G4-7TECZ Y 429 26.52 6,29,105,107,136
25 1800 230/460 284TC NB 58.0/29.0 92.4 S276 $1,703 G4-7TECZ N 429 26.74 6,29,105,107
30 3600 230/460 286TSC Ftd 70.0/35.0 91.0 S5262 $1,863 G4-7TECZ N 465 27.03 29,105,107
30 3600 230/460 286TSC Ftd 66.8/33.4 91.0 S2262 $1,863 G4-7TECZ N 455 26.65 6,29,105,107,136
30 1800 230/460 286TC Ftd 70.2/35.1 92.4 S5265 $1,827 G4-7TECZ Y 455 28.40 29,105,107
30 1800 230/460 286TC Ftd 69.0/34.5 92.4 S2265 $1,827 G4-7TECZ Y 475 28.02 6,29,105,107,136
30 1800 230/460 286TC NB 39.0/34.5 92.4 S277 $1,960 G4-7TECZ N 475 28.24 6,29,105,107
40 1800 230/460 324TC Ftd 91.0/45.5 93.0 S2340 $2,329 G4-7TECZ N 803 31.20
50 1800 230/460 326TC Ftd 114.4/57.2 93.0 S2341 $2,849 G4-7TECZ N 812 31.20
60 1800 230/460 364TC Ftd 136.4/68.2 93.6 S2342 $4,261 G4-7TECZ N 959 33.50
75 1800 230/460 365TC Ftd 173.4/86.7 94.1 S2343 $5,362 G4-7TECZ N 1019 34.50
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
105 Usable on 200/400V, 50Hz at 1.0 service factor
107 Y-Start/Delta-Run Capable
136 Discontinued when stock is depleted. Reference S52XX for new catalog number

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Totally Enclosed Fan-Cooled
NEMA Dimensions
1.14
Value Line™ TEFC

NEMA Frame D 2E 2F BA H N-W U V Min. Key Width Key Thickness Key Length
143T 3.50 5.50 4.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
145T 3.50 5.50 5.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
182T 4.50 7.50 4.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
284TS 7.00 11.00 9.50 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286TS 7.00 11.00 11.00 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
324TS 8.00 12.50 10.50 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326TS 8.00 12.50 12.00 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
364T 9.00 14.00 11.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365T 9.00 14.00 12.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
404T 10.00 16.00 12.25 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
404TS 10.00 16.00 12.25 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
405T 10.00 16.00 13.75 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
405TS 10.00 16.00 13.75 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
444T 11.00 18.00 14.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
444TS 11.00 18.00 14.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
445T 11.00 18.00 16.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
445TS 11.00 18.00 16.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
447T 11.00 18.00 20.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
447TS 11.00 18.00 20.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
449T 11.00 18.00 25.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
449TS 11.00 18.00 25.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.63 3.00
Notes
“C” dimension is overall length and is shown for each catalog number on rating pages.
All dimensions in inches. All dimensions are nominal. Request factory outlines for exact dimensions.
1. Motor base has two sets of holes at 3.00 and 5.00 inches.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Totally Enclosed Fan-Cooled
C-Face Dimensions
1.15

Value Line™ TEFC

All Dimensions in inches
NEMA Frame
AH AJ AK U Key Width Key Thickness Key Length
143TC-145TC 2.12 5.88 4.50 0.875 0.19 0.19 1.38
182TC-184TC 2.62 7.25 8.50 1.125 0.25 0.25 1.75
213TC-215TC 3.12 7.25 8.50 1.375 0.31 0.31 2.38
254TC-256TC 3.75 7.25 8.50 1.625 0.38 0.38 2.88
284TC-286TC 4.38 9.00 10.50 1.875 0.50 0.50 3.25

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

1.16

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Explosion Proof
Standard Features
1.17
Div 1, Class I, Group D
Div 1, Class II, Group E, F, G

Value Line™ TEFC-XP

HP Range 1.5-75
Poles 2,4,6
Voltage 230/460
Efficiency EPAct
Frequency 60
NEMA Design A or B
Agency Approvals UL - Motor Listing and Insulation System Recognition, CSA - Motors
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.11 in/sec Max.
Bearing Protection Brass Shaft Slinger - DE and ODE
Bearing Type Ball, 143T-286T Sealed; 284TS-286TS and 324-365 Open
Conduit Box Cast Iron
Drains Yes
End Shield Cast Iron
Fan Non Sparking
Fan Cover Steel plate
Fasteners Metric
Frame Material Cast Iron
Frame Size 182-365
Grease Grease: 182T-286T: Lithium 284TS-286TS and 324-365: Polyurea
Ground In Conduit Box
Insulation Class Non-Hygroscopic Class F
L10 Bearing Life Direct Coupled: 100,000 hrs, Belted: 20,000 hrs
Lifting Means 143-145: None, 182-365: Eyebolt
Mounting F1
Mounting Holes 1 per foot
Nameplate Stainless Steel
Paint Gray, Polyurethane
Relubrication 284TS-286TS and 324-365
Rotor Cast Aluminum
Service Factor 1.15 @ 40ºC
Temperature Code T3B, T2D
Temperature Rise 80ºC @ 1.0 SF
Tests NEMA Routine, IEEE 112
Thermal Protection 3 Normally Closed Thermostats (1 per phase) Klixon Type 9700K
Time Rating Continuous
Warranty 12 months from date of purchase or 18 months from date of shipment,
whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Explosion Proof
Pricing
1.18
Div 1, Class I, Group D
Div 1, Class II, Group E, F, G
Value Line™ TEFC-XP

Volts: 230/460
HP: 1.5 - 75
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol NormStk Wt (lbs) C Dim (in) Notes
1.5 1200 230/460 182T 4.9/2.5 85.5 S2601 $672 G5-7XPZ N 97 14.70 29, 109
2 1200 230/460 184T 5.9/3.0 86.5 S2603 $725 G5-7XPZ Y 112 14.70 29, 109
3 3600 230/460 182T 7.2/3.6 85.5 S2605 $686 G5-7XPZ Y 101 14.70 29, 109
3 1800 230/460 182T 7.8/3.8 87.5 S2606 $657 G5-7XPZ Y 106 14.70 29, 109
3 1200 230/460 213T 8.0/4.0 87.5 S2608 $856 G5-7XPZ Y 185 17.98 29, 109
5 3600 230/460 184T 11.6/5.8 87.5 S2610 $797 G5-7XPZ Y 121 15.75 6, 29, 109
5 1800 230/460 184T 12.5/6.3 87.5 S2611 $732 G5-7XPZ Y 123 15.75 29, 109
5 1200 230/460 215T 12.8/6.4 87.5 S2613 $1,110 G5-7XPZ Y 216 19.47 29, 109
7.5 3600 230/460 213T 18.0/19.0 88.5 S2615 $937 G5-7XPZ Y 189 17.98 29, 109
7.5 1800 230/460 213T 18.0/9.0 89.5 S2616 $932 G5-7XPZ Y 187 17.98 29, 109
7.5 1200 230/460 254T 19.3/9.6 89.5 S2618 $1,501 G5-7XPZ Y 308 23.70 29, 109
10 3600 230/460 215T 23.4/11.7 89.5 S2620 $1,096 G5-7XPZ Y 213 19.47 29, 109
10 1800 230/460 215T 23.6/11.8 89.5 S2621 $1,076 G5-7XPZ Y 216 19.47 29, 109
10 1200 230/460 256T 26.0/13.0 89.5 S2623 $1,760 G5-7XPZ Y 359 25.44 6, 29, 109
15 3600 230/460 254T 33.7/16.8 90.2 S2625 $1,466 G5-7XPZ Y 330 23.70 6, 29, 109
15 1800 230/460 254T 34.9/17.4 91.0 S2626 $1,446 G5-7XPZ Y 339 23.70 6, 29, 109
15 1200 230/460 284T 37.5/18.8 90.2 S2628 $2,345 G5-7XPZ Y 436 26.80 6, 29, 109
20 3600 230/460 256T 44.9/22.4 90.2 S2630 $1,735 G5-7XPZ Y 367 25.44 6, 29, 109
20 1800 230/460 256T 46.0/23.0 91.0 S2631 $1,719 G5-7XPZ Y 386 25.44 6, 29, 109
20 1200 230/460 286T 49.7/24.9 90.2 S2633 $2,758 G5-7XPZ Y 517 28.30 6, 29, 109
25 3600 230/460 284TS 55.9/28.0 91.0 S2635 $2,182 G5-7XPZ Y 464 25.43 6, 29, 109
25 1800 230/460 284T 57.9/29.0 92.4 S2636 $2,104 G5-7XPZ Y 488 26.80 6, 29, 109
25 1200 230/460 324T 62.3/31.1 91.7 S2638 $3,502 G5-7XPZ N 682 29.93 6, 29, 109
30 3600 230/460 286TS 67.5/33.7 91.0 S2640 $2,471 G5-7XPZ N 502 26.93 6, 29, 109
30 1800 230/460 286T 69.1/34.5 92.4 S2641 $2,372 G5-7XPZ Y 570 28.30 6, 29, 109
30 1200 230/460 326T 73.8/36.9 91.7 S2643 $3,925 G5-7XPZ Y 744 31.42 6, 29, 109
40 3600 230/460 324TS 89.3/44.6 91.7 S2644 $3,360 G5-7XPZ Y 691 28.43 6, 29, 109
40 1800 230/460 324T 90.5/45.2 93.0 S2645 $3,256 G5-7XPZ Y 717 29.93 6, 29, 109
40 1200 230/460 364T 94.2/47.1 93.0 S2647 $5,191 G5-7XPZ Y 871 33.55 6, 29, 109
50 3600 230/460 326TS 111.0/55.4 92.4 S2648 $4,148 G5-7XPZ Y 770 31.42 6, 29, 109
50 1800 230/460 326T 114.0/56.9 93.0 S2649 $3,836 G5-7XPZ Y 783 31.42 6, 29, 109
50 1200 230/460 365T 117.0/58.5 93.0 S2651 $5,836 G5-7XPZ N 928 33.55 29, 109
60 3600 230/460 364TS 131.0/65.3 93.0 S2653 $5,357 G5-7XPZ N 816 31.42 6, 29, 109
60 1800 230/460 364T 140.0/70.0 93.6 S2654 $5,318 G5-7XPZ N 911 33.55 6, 29, 109
75 3600 230/460 365TS 162.0/81.2 93.0 S2656 $5,612 G5-7XPZ N 997 31.42 6, 29, 109
75 1800 230/460 365T 173.0/86.3 94.1 S2657 $6,516 G5-7XPZ N 997 33.55 6, 29, 109
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz at 1.0 service factor
109 Usable on 200/400C, 50Hz at 1.0SF and derated to next lower HP

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Explosion Proof
NEMA Motor Dimensions
1.19
Div 1, Class I, Group D
Div 1, Class II, Group E, F, G

Value Line™ TEFC-XP

NEMA Frame D 2E 2F BA H N Min. U V Min. Key Width Key Thickness Key Length
182T 4.50 7.50 4.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
284TS 7.00 11.00 9.50 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286TS 7.00 11.00 11.00 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
324TS 8.00 12.50 10.50 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326TS 8.00 12.50 12.00 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
364T 9.00 14.00 11.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365T 9.00 14.00 12.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
Notes
“C” dimension is overall length and is shown for each catalog number on rating pages.
All dimensions in inches. All dimensions are nominal. Request factory outlines for exact dimensions.
1. Motor base has two sets of holes at 3.00 and 5.00 inches.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Kits and Accessories
NEMA 143 to 449T Frames
1.20
C-Face Kit
C-Face kits are available for many stock motors. For the convenience of the experienced user, we have listed the part numbers
of those most commonly needed. If you are not sure of the product structure a specific listing of the applicable kits can be
found in Elitenet. Please use this resource as an incorrect selection will be subject to a re-stocking charge.
Value Line™ Kits

On footed motors the dimension from the foot mounting hole to the C-face or shaft shoulder is shorter than NEMA standard by
3/4" on frames 182-215 and shorter by 1/2" on frames 254-256.

Open Dripproof Motors

Cat No. Part No. Frame Poles List Price Price Symbol Norm Stk
A1058 249A9573AAG09 143T-145T2 2-4-6 $82 G4-7KITS Y
A1059 249A9573AAG10 182T-184T2 2-4-6 $112 G4-7KITS Y
A1060 249A9573AAG11 213T-215T2 2-4-6 $138 G4-7KITS Y
A268 249A9500ABPT4 254-256T1 2-4-6 $169 G4-7KITS Y
A1061 249A9573AAG12 254T-256T2 2-4-6 $160 G4-7KITS Y
A270 249A9500ABPT5 284-286T1 2-4-6 $258 G4-7KITS Y
A269 249A9500ABPT6 284TS-286TS1 2-4-6 $258 G4-7KITS Y
A1050 249A9573AAG01 284T(S)-286T(S)2,3 2-4-6 $258 G4-7KITS Y
A1071 249A9500ABPT7 324T-326T1 2-4-6 $418 G4-7KITS Y
A1071 249A9500ABPT7 324TS-326TS1 4 $418 G4-7KITS Y
A1072 249A9500ABPT8 324TS-326TS 2 $418 G4-7KITS Y
A1051 249A9573AAG02 324T(S)-326T(S)2 2-4-6 $418 G4-7KITS Y
A1073 249A9500ABPT9 364T-365T1 2-4-6 $539 G4-7KITS Y
A1073 249A9500ABPT9 364TS-365TS1 4 $539 G4-7KITS Y
A1074 249A9500ABPT10 364TS-365TS1 2 $539 G4-7KITS Y
A1053 249A9573AAG04 364T-365T2 4-6 $539 G4-7KITS Y
A1052 249A9573AAG03 364TS-365TS2 2 $539 G4-7KITS Y
A1075 249A9500ABPT11 404T-405T1 2-4-6 $785 G4-7KITS Y
A1075 249A9500ABPT11 404TS-405TS1 4 $785 G4-7KITS Y
A1076 249A9500ABPT12 404TS-405TS1 2 $785 G4-7KITS Y
A1062 249A9573AAG13 404T(S)2,3 6 $835 G4-7KITS Y
A1063 249A9573AAG14 405T(S)2,3 6 $835 G4-7KITS Y
A1055 249A9573AAG06 404T(S)-405T(S)2,3 4 $857 G4-7KITS Y
A1054 249A9573AAG05 404TS-405TS2 2 $725 G4-7KITS Y
A1077 249A9500ABPT13 444T-445T1 2-4-6 $857 G4-7KITS Y
A1077 249A9500ABPT13 444TS-445TS1 4 $857 G4-7KITS Y
A1078 249A9500ABPT14 444TS-445TS1 2 $857 G4-7KITS Y
A1057 249A9573AAG08 444T(S)-445T(S)2,3 4-6 $857 G4-7KITS Y
A1056 249A9573AAG07 444TS-445TS2 2 $857 G4-7KITS Y
A1079 249A9500ABPT15 447T-449T 1
2-4-6 $993 G4-7KITS Y
A1079 249A9500ABPT15 447TS-449TS1 4 $993 G4-7KITS Y
A1080 249A9500ABPT16 447TS-449TS1 2 $993 G4-7KITS Y
1. For use on models with ‘AC’ in the motor model code, e.g. 5KE254AC206
2. For use on models with ‘ATE’ in the motor model code, e.g 5KE254ATE205
3. For use on models with ‘T’ or ‘TS’ type shaft dimensions

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Value Line™
Kits and Accessories
NEMA 143 to 449T Frames cont.
1.21
C-Face Kits cont.
Totally Enclosed Fan Cooled Motors
Cat No. Part No. Frame/Poles List Price Price Symbol Norm Stk
A272 249A9500AAPT21 143T-145T1,6 $98 G4-7KITS Y

Value Line™ Kits

A1064 249A9573ABG01 143T-145T3 $98 G4-7KITS Y
A274 249A9500AAPT22 182T-184T1,6 $134 G4-7KITS Y
A1065 249A9573ABG02 182T-184T 3
$134 G4-7KITS Y
A280 249A9500AAPT23 213T-215T1,6 $167 G4-7KITS Y
A1066 249A9573ABG03 213T-215T3 $167 G4-7KITS Y
A281 249A9500AAPT24 254T-256T1,6 $224 G4-7KITS Y
A1067 249A9573ABG04 254T-256T3 $224 G4-7KITS Y
A282 249A9500AAPT6 284TS-286TS1,6 $224 G4-7KITS Y
A283 249A9500AAPT25 284T-286T1,6 $297 G4-7KITS Y
A1068 249A9573ABG05 284T-286T3 $297 G4-7KITS Y
A1021 249A9514AAG01 324T-326T, 324TS-326TS2,4 $441 G4-7KITS Y
A1022 249A9514AAG02 324T-326T, 324TS-326TS2,5 $441 G4-7KITS Y
A1069 249A9573ABG06 324T-326T3 $441 G4-7KITS Y
A1023 249A9514AAG03 364T-365T, 364TS-365TS2,4 $450 G4-7KITS Y
A1024 249A9514AAG04 364T-365T, 364TS-365TS2,5 $450 G4-7KITS Y
A1025 249A9514AAG05 404T-405T2,6 $483 G4-7KITS Y
A1026 249A9514AAG06 404TS-405TS2,6 $483 G4-7KITS Y
A1027 249A9514AAG07 444T-445T2,6 $595 G4-7KITS Y
A1028 249A9514AAG08 444TS-445TS2,6 $595 G4-7KITS Y
Notes
143-256 frame will not meet NEMA BA dimension using C-Face kit
1. For use on models with ‘BC’ or ‘SC’ in the motor model code, e.g. 5KE256BC205 or 5KE256SC205
2. For use on models with ‘BFC’ or ‘SFC’ in the motor model code, e.g. 5KE364BFC205 or 5KE364SFC205
3. For use on models with ‘BTE’ or ‘STE’ in the motor model code, e.g. 5KE256BTE205 or 5KE256STE205
4. For use on models with A suffix or no suffix, e.g. 5KE364BFC205 or 5KE364BFC205A
5. For use on models with B or higher suffix, e.g. 5KE364BFC205B
6. For use on models with ALL suffixes

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Value Line™
Kits and Accessories
NEMA 143 to 449T Frames cont.
1.22
6
Sliding Bases for 215-364 Frame Motors
Bases are suitable for the indicated frame size and is suitable for the majority of floor-mounted, belt-connected motors. These
bases are not suitable for ceiling or side-wall mounting installations. The 213-215 frame size bases are closed frame construction
with two adjusting screws. The 254-364 frame size bases are open frame construction with two adjusting screws.
Value Line™ Kits

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A100 249A9598AA1 213 $60 GO-1R Y
A101 249A9598AA2 215 $60 GO-1R Y
A102 249A9598AA3 254 $71 GO-1R Y
A103 249A9598AA4 256 $71 GO-1R Y
A104 249A9598AA5 284 $91 GO-1R Y
A105 249A9598AA6 286 $91 GO-1R Y
A106 249A9598AA7 324 $105 GO-1R Y
A107 249A9598AA8 326 $105 GO-1R Y
A108 249A9598AA9 364 $186 GO-1R Y

Space Heater Kits3,4

Cat No. Frame Volts List Price Price Symbol Norm Stk
A233 182-184 110-120 $107 G4-7KITS N
A239 182-184 220-240 $107 G4-7KITS N
A234 213-326 110-120 $111 G4-7KITS N
A235 213-326 220-240 $111 G4-7KITS N
A236 213-326 440-480 $111 G4-7KITS N
A237 364-405 110-120 $188 G4-7KITS N
A238 364-405 220-240 $188 G4-7KITS N
A240 364-405 440-480 $188 G4-7KITS N
A241 444-449 110-120 $203 G4-7KITS Y
A242 444-449 220-240 $203 G4-7KITS N
A244 444-449 440-480 $203 G4-7KITS N
3. Includes insulation and strip heater.
4. No separate heater nameplate furnished. The existing motor nameplate is to be stamped with heater volts and watts.

Stud Grounding Kit1

Suitable for cast iron, aluminum or steel conduit boxes.
Cat No. Frame List Price Price Symbol Norm Stk
A300 324 TO 405 $158 G6-7KITS N
A301 444 TO 449 $158 G6-7KITS N
1. Each kit contains 2 jam nuts, grounding stud, and assembly instructions.

Thermostat Kit2
For Dripproof and Totally Enclosed Fan Cooled Motors
Cat No. Temperature Class Opening Temperature List Price Price Symbol Norm Stk
A337 F 155-165C $69 G4-7KITS N
2. Thermostat leads are 29 inches long with terminals.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Energy $aver®
Open Dripproof
Standard Features

HP Range 1-300
Poles 2,4,6
Voltage 200, 230/460, 460, 575
Efficiency NEMA Premium
2.1
Frequency 60 Hz (50 Hz for 230/460 Voltage ratings)
NEMA Design A or B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390

Energy $aver® – ODP

Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.15in/sec max
Bearing Caps 324-449
Bearing Type Ball, Belted 4-pole 150-300 HP have Roller Brg
Conduit Box Stamped Steel
End Shield Cast Iron
Fasteners Metric
Frame Material Cast Iron
Frame Size 143-449
Grease 143-286: Lithium, 324-449: Polyurea
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System GEGARD1800™, Non-Hygroscopic, Anti-Fugus, meets, NEMA MG1-31
Inverter Capabilities Variable Torque 20:1, Constant Torque 4:1
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 26,280 hrs, Exceptions: 180/4P: 50,843 hrs, 210/4P: 43,214 hrs
Lifting Means Eye Bolt
Mounting F1 as Standard and Modifiable to F2
Mounting Holes 1 per foot
Nameplate Stainless Steel
Paint Buff, Alkyd
Relubrication 324-449
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine, IEEE 112
Time Rating Continuous
Warranty 24 months from date of purchase or 30 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Energy $aver®
Open Dripproof
Pricing

Volts: 230/460, 575

HP: 1-300
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
1 1800 230/460 143T 2.8/1.4 85.5 E707 $222 G4-7D$Z1 Y 46 10.54 29, 84
1 1200 230/460 145T 3.4/1.7 82.5 E708 $285 G4-7D$Z1 Y 58 11.53 29, 84
1.5 3600 230/460 143T 3.8/1.9 84.0 E709 $242 G4-7D$Z1 Y 46 10.54 29, 84
1.5 1800 230/460 145T 4.2/2.1 86.5 E710 $242 G4-7D$Z1 Y 56 11.53 29, 84
1.5 1200 230/460 182T 5.4/2.7 86.5 E7707 $313 G4-7D$Z1 Y 72 12.53 29, 84
2 3600 230/460 145T 5.1/2.6 85.5 E717 $285 G4-7D$Z1 Y 58 11.53 29, 84
2.2 2 1800 230/460 145T 5.4/2.7 86.5 E718 $267 G4-7D$Z1 Y 58 11.53 29, 84
2 1200 230/460 184T 7.0/3.5 87.5 E7710 $402 G4-7D$Z1 Y 91 13.53 29, 84
3 3600 230/460 145T 7.6/3.8 85.5 E719 $320 G4-7D$Z1 Y 60 11.53 29, 84
3 1800 200 182T 9.0 89.5 E7714 $277 G4-7D$Z1 N 72 12.53 84
Energy $aver® – ODP

3 1800 230/460 182T 7.8/3.9 89.5 E720 $277 G4-7D$Z1 Y 72 12.53 29, 84
3 1800 575 182T 3.2 89.5 E7635 $277 G4-7D$Z1 N 72 12.53
3 1200 230/460 213T 9.8/4.9 88.5 E7011 $514 G4-7D$Z1 Y 128 15.85 29, 84
5 3600 230/460 182T 12.0/6.0 86.5 E721 $389 G4-7D$Z1 Y 72 12.53 29, 84
5 1800 200 184T 14.7 89.5 E7716 $389 G4-7D$Z1 N 91 13.53 84
5 1800 230/460 184T 12.8/6.4 89.5 E722 $389 G4-7D$Z1 Y 91 13.53 29, 84
5 1800 575 184T 5.2 89.5 E7808 $389 G4-7D$Z1 N 91 13.53
5 1200 230/460 215T 13.8/6.9 89.5 E7012 $643 G4-7D$Z1 Y 157 17.38 29, 84
7.5 3600 230/460 184T 17.4/8.7 88.5 E723 $560 G4-7D$Z1 Y 91 13.53 29, 84
7.5 1800 200 213T 22.5 91.0 E7729 $538 G4-7D$Z1 N 128 15.85 84
7.5 1800 230/460 213T 19.4/9.7 91.0 E730 $538 G4-7D$Z1 Y 128 15.85 29, 84
7.5 1800 575 213T 7.8 91.0 E7640 $538 G4-7D$Z1 N 157 17.38
7.5 1200 230/460 254T 20.4/10.2 90.2 E7013 $838 G4-7D$Z1 Y 260 20.67 29, 84
10 3600 230/460 213T 25.8/12.9 89.5 E750 $665 G4-7D$Z1 Y 163 15.85 29, 84
10 1800 200 215T 28.8 91.7 E7734 $650 G4-7D$Z1 N 157 17.38 84
10 1800 230/460 215T 24.8/12.4 91.7 E731 $650 G4-7D$Z1 Y 157 17.38 29, 84
10 1800 575 215T 10.1 91.7 E7643 $650 G4-7D$Z1 Y 157 17.38
10 1200 230/460 256T 27.8/13.9 91.7 E7014 $981 G4-7D$Z1 Y 310 22.40 29, 84
15 3600 230/460 215T 37.8/18.9 90.2 E751 $842 G4-7D$Z1 Y 157 17.38 29, 84
15 1800 200 254T 42.6 93.0 E7744 $864 G4-7D$Z1 N 260 20.67 84
15 1800 230/460 254T 37.2/18.6 93.0 E732 $864 G4-7D$Z1 Y 260 20.67 29, 84
15 1800 575 254T 14.9 93.0 E7646 $864 G4-7D$Z1 N 260 20.67
15 1200 230/460 284T 37.8/18.9 91.7 E7015 $1,263 G4-7D$Z1 Y 394 23.82 29, 84
20 3600 230/460 254T 46.0/23.0 91.0 E752 $993 G4-7D$Z1 Y 260 20.67 29, 84
20 1800 200 256T 55.4 93.0 E7754 $1,055 G4-7D$Z1 N 310 22.40 84
20 1800 230/460 256T 48.2/24.1 93.0 E733 $1,055 G4-7D$Z1 Y 310 22.40 29, 84
20 1800 575 256T 19.3 93.0 E7649 $1,055 G4-7D$Z1 N 310 22.40
20 1200 230/460 286T 51.3/25.7 92.4 E7017 $1,549 G4-7D$Z1 Y 436 25.32 29, 84
25 3600 230/460 256T 57.4/28.7 91.7 E753 $1,212 G4-7D$Z1 Y 310 22.40 29, 84
25 1800 200 284T 76.7 93.6 E7757 $1,226 G4-7D$Z1 N 394 23.82 84
25 1800 230/460 284T 66.2/33.1 93.6 E734 $1,226 G4-7D$Z1 Y 394 23.82 29, 84
25 1800 575 284T 26.5 93.6 E7652 $1,226 G4-7D$Z1 N 394 23.82
25 1200 230/460 324T 64.2/32.1 93.0 E7019 $1,838 G4-7D$Z1 Y 580 26.26 29, 84
Notes
29 Usable on 200 volts at 1.0 service factor
84 Designed for 50 or 60 Hz operation

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Energy $aver®
Open Dripproof
Pricing cont.

Volts: 230/460, 575

HP: 1-300
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
30 3600 230/460 284TS 70.0/35.0 91.7 E754 $1,446 G4-7D$Z1 Y 420 22.45 29, 84
30 1800 200 286T 83.7 94.1 E7763 $1,425 G4-7D$Z1 N 436 25.32 84
30 1800 230/460 286T 72.4/36.2 94.1 E735 $1,425 G4-7D$Z1 Y 436 25.32 29, 84
30 1800 575 286T 29.3 94.1 E7654 $1,425 G4-7D$Z1 N 436 25.32
30 1200 230/460 326T 77.4/38.7 93.6 E7022 $2,103 G4-7D$Z1 Y 639 27.76 29, 84
40 3600 230/460 286TS 106.0/53.0 92.4 E755 $1,850 G4-7D$Z1 Y 445 23.95 29, 84
40 1800 230/460 324T 97.0/48.5 94.1 E736 $1,772 G4-7D$Z1 Y 480 26.26 29, 84 2.3
40 1800 575 324T 39.1 94.1 E7310 $1,772 G4-7D$Z1 N 580 26.26
40 1200 460 364T 48.2 94.1 E7024 $3,091 G4-7D$Z1 Y 770 29.13
50 3600 230/460 324TS 116.4/58.2 93.0 E756 $2,199 G4-7D$Z1 Y 606 24.76 29, 84

Energy $aver® – ODP

50 1800 230/460 326T 121.0/60.5 94.5 E737 $2,066 G4-7D$Z1 Y 639 27.76 29, 84
50 1800 575 326T 48.6 94.5 E7320 $2,066 G4-7D$Z1 N 639 27.76
50 1800 230/460 326TS 121.0/60.5 94.5 E7254 $2,066 G4-7D$Z1 Y 639 26.26 29, 84
50 1200 460 365T 61.0 94.1 E7026 $3,610 G4-7D$Z1 Y 838 30.13
60 3600 230/460 326TS 136.4/68.2 93.6 E757 $2,650 G4-7D$Z1 Y 692 26.26 29, 84
60 1800 230/460 364T 150.6/75.3 95.0 E7381 $2,684 G4-7D$Z1 Y 770 29.13 29, 84
60 1800 575 364T 60.2 95.0 E7330 $2,684 G4-7D$Z1 N 770 29.13
60 1800 230/460 364TS 150.6/76.5 95.0 E7383 $2,684 G4-7D$Z1 Y 770 27.00 29, 84
60 1200 460 404T 72.9 94.5 E7029 $4,467 G4-7D$Z1 Y 1090 33.10
75 3600 230/460 364TS 183.0/91.5 93.6 E758 $3,533 G4-7D$Z1 Y 686 27.00 29, 84
75 1800 230/460 365T 182.4/91.2 95.0 E7391 $3,269 G4-7D$Z1 Y 838 30.13 29, 84
75 1800 575 365T 73.9 95.0 E7825 $3,269 G4-7D$Z1 N 838 30.13
75 1800 230/460 365TS 182.4/91.2 95.0 E7393 $3,269 G4-7D$Z1 Y 838 28.00 29, 84
75 1200 460 405T 91.1 94.5 E7032 $5,316 G4-7D$Z1 Y 1150 34.60
100 3600 230/460 365TS 232.0/116.0 93.6 E759 $4,641 G4-7D$Z1 Y 812 28.00 29, 84
100 1800 230/460 404T 226.0/113.0 95.4 E7401 $4,167 G4-7D$Z1 Y 1090 33.10 29, 84
100 1800 575 404T 90.7 95.4 E7340 $4,167 G4-7D$Z1 N 1090 33.10
100 1800 230/460 404TS 226.0/113.0 95.4 E7257 $4,167 G4-7D$Z1 Y 1090 30.10 29, 84
100 1200 460 444T 120.0 95.0 E7034 $6,733 G4-7D$Z1 Y 1494 37.70
125 3600 460 404TS 142.0 94.1 E7501 $5,774 G4-7D$Z1 Y 1092 30.10
125 1800 460 405T 142.0 95.4 E741 $4,992 G4-7D$Z1 Y 1150 34.60
125 1800 460 405TS 142.0 95.4 E7342 $4,992 G4-7D$Z1 Y 1150 30.10
125 1200 460 445T 150.0 95.0 E7036 $8,268 G4-7D$Z1 Y 1715 39.70
150 3600 460 405TS 170.0 94.1 E7502 $7,024 G4-7D$Z1 Y 1194 30.10
150 1800 460 444T 168.0 95.8 E742 $7,209 G4-7D$Z1 Y 1494 37.70
150 1800 460 444TS 168.0 95.8 E7259 $7,209 G4-7D$Z1 Y 1494 33.95
150 1200 460 447T 177.0 95.4 E7962 $9,166 G4-7D$Z1 Y 2100 43.20
200 3600 460 444TS 224.0 95.0 E7503 $12,368 G4-7D$Z1 Y 1590 33.95
200 1800 460 445T 223.0 95.8 E743 $10,150 G4-7D$Z1 Y 1715 39.70
200 1800 460 445TS 223.0 95.8 E7360 $10,150 G4-7D$Z1 Y 1715 35.95
200 1200 460 449T 235.0 95.4 E7963 $14,829 G4-7D$Z1 Y 2150 49.77
250 3600 460 445TS 275.0 95.0 E7504 $14,387 G4-7D$Z1 N 1800 35.95
250 1800 460 447T 276.0 95.8 E7272 $12,600 G4-7D$Z1 N 2100 43.20
250 1800 460 447TS 276.0 95.8 E7370 $12,600 G4-7D$Z1 N 2100 39.46
300 1800 460 449T 331.0 95.8 E7273 $15,541 G4-7D$Z1 N 2150 49.77
Notes
29 Usable on 200 volts at 1.0 service factor
84 Designed for 50 or 60 Hz operation

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Energy $aver®
Open Dripproof
Dimensions C

N MIN

V
KEY LENGTH

2.4 2E H HOLE 2F BA

Note: “C” dimensions is overall and is shown for each catalog number on rating pages. (All dimensions in inches)
Energy $aver® – ODP

NEMA Key Key

Frame D 2E 2F BA H N Min. U V Min. Key Width Thickness Length
143T 3.50 5.50 4.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
145T 3.50 5.50 5.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
182T 4.50 7.50 4.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
284TS 7.00 11.00 9.50 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286TS 7.00 11.00 11.00 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
324TS 8.00 12.50 10.50 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326TS 8.00 12.50 12.00 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
364T 9.00 14.00 11.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365T 9.00 14.00 12.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
404T 10.00 16.00 12.25 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
404TS 10.00 16.00 12.25 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
405T 10.00 16.00 13.75 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
405TS 10.00 16.00 13.75 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
444T 11.00 18.00 14.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
444TS 11.00 18.00 14.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
445T 11.00 18.00 16.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
445TS 11.00 18.00 16.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
447T 11.00 18.00 20.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
447TS 11.00 18.00 20.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
449T 11.00 18.00 25.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
1. Motor base has two sets of holes at 3.00 and 5.00 inches.
Note: All dimensions are nominal. Request factory outlines for exact dimensions.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW Energy $aver®
TEFC-Severe Duty
Standard Features

HP Range 1-250 2.5

Poles 2 and 4
Voltage 200-230/460, 460, 575

Energy $aver® – TEFC-SD

Efficiency NEMA Premium
Frequency 60 Hz (See notes for 50 Hz)
NEMA Design A or B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390 - CE mark up to 320 frame
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.15in/sec max
Bearing Type Ball, 143T-286TS sealed; 324-449 open
Conduit Box Cast Iron
End Shield Cast Iron
Fasteners 143-326 Metric; 364-449 ASE
Frame Material Cast Iron
Frame Size 143-449
Grease 143-286 Lithium; 324-449 Polyurea
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System GEGARD1800, Non-Hygroscopic, Anti-Fungus meeting NEMA MG1-31
Inverter Capabilities Variable Torque 10:1, Constant Torque 4:1
L10 Bearing Life Direct Coupled 65,000 hrs; Belted 26,280 hrs
Lifting Means 143-145 None; 182-326 Eye Bolt; 364-449 Four Cast-in Lifting Lugs
Mounting F1 as Standard and Modifiable to F2
Mounting Holes 143-324 One Per Foot; 364-449 Two Per Foot
Nameplate Stainless Steel
Paint All Frames - Buff; 143-326 Alkyd; 364-449 Epoxyester
Relubrication 324-449
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine, IEEE 112-B
Time Rating Continuous
Vibration 0.08 in/sec
Warranty 36 months from date of purchase or 42 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Energy $aver® NEW
TEFC-Severe Duty
Pricing

Volts: 230/460, 460, 575

HP: 1-250
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
1 3600 230/460 143T 4.0/2.0 77.0 M7700 $328 G4-7S$P1 Y 52 12.25 29, 105, 131
1 1800 230/460 143T 3.0/1.5 85.5 M7723 $332 G4-7S$P1 Y 52 12.25 29, 105, 131
1.5 3600 230/460 143T 4.5/2.25 84.0 M7701 $356 G4-7S$P1 Y 52 12.25 29, 105, 131
1.5 1800 230/460 145T 4.6/2.3 86.5 M7724 $369 G4-7S$P1 Y 58 13.24 29, 105, 131
2 3600 230/460 145T 5.0/2.5 85.5 M7702 $426 G4-7S$P1 Y 52 13.24 29, 105, 131
2.6 2 1800 230/460 145T 4.2/2.1 86.5 M7725 $406 G4-7S$P1 Y 58 13.24 29, 105, 131
3 3600 230/460 182T 7.2/3.6 86.5 M7703 $479 G4-7S$P1 Y 96 14.43 29, 105, 131
3 1800 230/460 182T 8.0/4.0 89.5 M7726 $450 G4-7S$P1 Y 96 14.43 6, 29, 105, 131
Energy $aver® – TEFC-SD

5 3600 230/460 184T 11.6/5.8 88.5 M7704 $593 G4-7S$P1 Y 106 15.42 29, 105, 131
5 1800 230/460 184T 13.4/6.7 89.5 M7727 $525 G4-7S$P1 Y 106 15.42 6, 29, 105, 131
7.5 3600 230/460 213T 18.2/9.1 89.5 M7705 $717 G4-7S$P1 Y 168 17.94 29, 105, 107, 131
7.5 1800 230/460 213T 19.6/9.8 91.7 M7728 $713 G4-7S$P1 Y 168 17.94 6, 29, 105, 107, 131
10 3600 230/460 215T 23.2/11.6 90.2 M7706 $838 G4-7S$P1 Y 192 19.43 29, 105, 107, 131
10 1800 230/460 215T 25.4/12.7 91.7 M7729 $859 G4-7S$P1 Y 192 19.43 6, 29, 105, 107, 131
15 3600 230/460 254T 35.2/17.6 91.0 M7707 $1,151 G4-7S$P1 Y 290 23.4 29, 105, 107, 131
15 1800 230/460 254T 36.5/18.3 92.4 M7730 $1,131 G4-7S$P1 Y 290 23.40 6, 29, 105, 107, 131
20 3600 230/460 256T 46.0/23.0 91.0 M7708 $1,426 G4-7S$P1 Y 325 25.10 29, 105, 107, 131
20 1800 230/460 256T 49.0/24.5 93.0 M7731 $1,409 G4-7S$P1 Y 325 25.10 29, 105, 107, 131
25 3600 230/460 284TS 57.0/28.5 91.7 M7709 $1,637 G4-7S$P1 N 445 25.53 29, 105, 107, 131
25 3600 230/460 284T 57.0/28.5 91.7 M7749 $1,637 G4-7S$P1 Y 445 26.90 29, 105, 107, 131
25 1800 230/460 284T 61.0/30.5 93.6 M7732 $1,562 G4-7S$P1 Y 430 26.90 6, 29, 105, 107, 131
30 3600 230/460 286TS 69.0/34.5 91.7 M7710 $1,911 G4-7S$P1 N 465 27.03 29, 105, 107, 131
30 3600 230/460 286T 69.0/34.5 91.7 M7750 $1,911 G4-7S$P1 Y 475 28.40 29, 105, 107, 131
30 1800 230/460 286T 73.0/36.5 93.6 M7733 $1,768 G4-7S$P1 Y 475 28.40 6, 29, 105, 107, 131
40 3600 230/460 324TS 91.4/45.7 92.4 M7711 $2,452 G4-7S$P1 Y 640 26.32 105, 107, 131
40 3600 230/460 324T 91.4/45.7 92.4 M7712 $2,452 G4-7S$P1 N 650 29.70 105, 107, 131
40 1800 230/460 324T 94.0/47.0 94.1 M7734 $2,348 G4-7S$P1 Y 650 29.70 6, 105, 107, 131
40 1800 230/460 324TS 94.0/47.0 94.1 M7735 $2,348 G4-7S$P1 N 640 26.32 6, 105, 107, 131
50 3600 230/460 326TS 114.0/57.0 93.0 M7713 $3,173 G4-7S$P1 Y 700 27.82 105, 107, 131
50 3600 230/460 326T 114.0/57.0 93.0 M7714 $3,173 G4-7S$P1 N 710 31.32 105, 107, 131
50 1800 230/460 326T 118.0/59.0 94.5 M7736 $2,884 G4-7S$P1 Y 710 31.32 6, 105, 107, 131
50 1800 230/460 326TS 118.0/59.0 94.5 M7737 $2,884 G4-7S$P1 N 700 27.82 6, 105, 107, 131
60 3600 460 364TS 71.9 93.6 M7909 $5,757 G4-7S$P N 930 32.76
60 3600 575 364TS 59.3 93.6 M7907 $5,757 G4-7S$P N 930 32.76
60 1800 460 364T 73.4 95.0 M7931 $5,637 G4-7S$P Y 990 34.89 6
60 1800 575 364T 58.7 95.0 M7929 $5,637 G4-7S$P N 990 34.89
75 3600 460 365TS 88.8 93.6 M7912 $7,067 G4-7S$P N 970 32.76
75 3600 575 365TS 71.0 93.6 M7910 $7,067 G4-7S$P N 970 32.76
75 1800 460 365T 89.7 95.4 M7934 $6,834 G4-7S$P Y 1040 34.89 6
75 1800 575 365T 71.8 95.4 M7932 $6,834 G4-7S$P N 1040 34.89
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz, same HP, at 1.0 service factor
105 Usable on 200/400V, 50Hz, same HP, at 1.0 service factor
106 Usable on 400V, 50Hz, same HP, at 1.0 service factor
107 Y-Start/Delta-Run Capable
131 Usable on 200/400V, 50 Hz at 1.15SF and de-rated to next lower HP

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW Energy $aver®
TEFC-Severe Duty
Pricing cont.

Volts: 230/460, 575

HP: 1-250
HP RPM Volts Frame FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
100 3600 460 405TS 112.0 94.1 M7914 $9,151 G4-7S$P N 1420 36.76
100 3600 575 405TS 89.4 94.1 M7913 $9,151 G4-7S$P N 1420 36.76
100 1800 460 405T 122.0 95.4 M7936 $8,441 G4-7S$P Y 1450 39.77
100 1800 575 405T 96.3 95.4 M7935 $8,441 G4-7S$P N 1450 39.77
125 3600 460 444TS 141.0 95.0 M7916 $11,953 G4-7S$P N 1780 41.87
125 3600 575 444TS 113.0 95.0 M7915 $11,416 G4-7S$P N 1780 41.87 2.7
125 1800 460 444T 144.0 95.4 M7938 $10,606 G4-7S$P Y 1880 45.62
125 1800 575 444T 117.0 95.4 M7937 $10,606 G4-7S$P N 1860 45.62

Energy $aver® – TEFC-SD

150 3600 460 445TS 168.0 95.0 M7918 $13,728 G4-7S$P N 1830 41.87
150 3600 575 445TS 135.0 95.0 M7917 $13,728 G4-7S$P N 1810 41.87
150 1800 460 445T 171.0 95.8 M7940 $12,339 G4-7S$P Y 2020 45.62
150 1800 575 445T 140.0 95.8 M7939 $12,339 G4-7S$P N 1990 45.62
200 3600 460 447TS 216.0 95.4 M7920 $17,379 G4-7S$P N 2420 50.37
200 3600 575 447TS 173.0 95.4 M7919 $17,379 G4-7S$P N 2420 50.37
200 1800 460 447T 225.0 96.2 M7942 $15,478 G4-7S$P Y 2580 54.12
200 1800 575 447T 179.0 96.2 M7941 $15,478 G4-7S$P N 2560 54.12
250 3600 460 449TS 267.0 95.8 M7922 $22,392 G4-7S$P N 2580 50.37
250 3600 575 449TS 214.0 95.8 M7921 $22,392 G4-7S$P N 2580 50.37
250 1800 460 449T 281.0 96.2 M7944 $18,099 G4-7S$P Y 2660 54.12
250 1800 575 449T 224.0 96.2 M7943 $18,099 G4-7S$P N 2660 54.12

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Energy $aver® NEW
TEFC-Severe Duty
C-Face
Price and Dimensions
Volts: 230/460
HP: 1-30
HP RPM Volts Frame Base FLA Nom Eff Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
1 1800 230/460 143TC Ftd 3.0/1.5 85.5 M7738 $360 G4-7S$P1 Y 50 12.90 29, 105, 132
1.5 1800 230/460 145TC Ftd 2.3 86.5 M7739 $390 G4-7S$P1 Y 61 13.90 29, 105, 132
2 1800 230/460 145TC Ftd 4.2/2.1 86.5 M7740 $440 G4-7S$P1 Y 64 13.90 29, 105, 132
3 3600 230/460 182TC Ftd 7.2/3.6 86.5 M7715 $505 G4-7S$P1 Y 88 15.34 29, 105, 132
3 1800 230/460 182TC Ftd 8.0/4.0 89.5 M7741 $485 G4-7S$P1 Y 92 15.34 6, 29, 105, 132
5 3600 230/460 184TC Ftd 11.6/5.8 88.5 M7716 $620 G4-7S$P1 Y 112 16.32 29, 105, 132
2.8
5 1800 230/460 184TC Ftd 13.4/6.7 89.5 M7742 $575 G4-7S$P1 Y 117 16.32 6, 29, 105, 132
Energy $aver® – TEFC-SD C-Face

7.5 3600 230/460 213TC Ftd 18.2/9.1 89.5 M7717 $810 G4-7S$P1 Y 151 17.78 29, 105, 107, 132
7.5 1800 230/460 213TC Ftd 19.6/9.8 91.7 M7743 $810 G4-7S$P1 Y 155 17.78 6, 29, 105, 107, 132
10 3600 230/460 215TC Ftd 23.2/11.6 90.2 M7718 $966 G4-7S$P1 Y 190 19.27 29, 105, 107, 132
10 1800 230/460 215TC Ftd 25.4/12.7 91.7 M7744 $966 G4-7S$P1 Y 203 19.27 6, 29, 105, 107, 132
15 3600 230/460 254TC Ftd 35.2/17.6 91.0 M7719 $1,250 G4-7S$P1 Y 287 23.70 29, 105, 107, 132
15 1800 230/460 254TC Ftd 36.5/18.3 92.4 M7745 $1,260 G4-7S$P1 Y 285 23.70 6, 29, 105, 107, 132
20 3600 230/460 256TC Ftd 46.0/23.0 91.0 M7720 $1,640 G4-7S$P1 Y 344 25.40 29, 105, 107, 132
20 1800 230/460 256TC Ftd 49.0/24.5 93.0 M7746 $1,640 G4-7S$P1 Y 329 25.40 29, 105, 107, 132
25 3600 230/460 284TSC Ftd 57.0/28.5 91.7 M7721 $1,950 G4-7S$P1 N 477 25.33 29, 105, 107, 132
25 1800 230/460 284TC Ftd 61.0/30.5 93.6 M7747 $1,950 G4-7S$P1 Y 482 26.70 6, 29, 105, 107, 132
30 3600 230/460 286TSC Ftd 69.0/34.5 91.7 M7722 $2,300 G4-7S$P1 N 522 26.83 29, 105, 107, 132
30 1800 230/460 286TC Ftd 73.0/36.5 93.6 M7748 $2,250 G4-7S$P1 Y 508 28.20 6, 29, 105, 107, 132
Notes
6 NEMA Design A
29 Usable on 200 Volts, 60Hz, same HP, at 1.0 service factor
105 Usable on 200/400V, 50Hz, same HP, at 1.0 service factor
106 Usable on 400V, 50Hz, same HP, at 1.0 service factor
107 Y-Start/Delta-Run Capable
132 Usable on 200/400V, 50 Hz at 1.15SF and de-rated to next lower HP

All Dimensions in inches

NEMA Frame
AH AJ AK U Key Width Key Thickness Key Length
143TC-145TC 2.12 5.88 4.50 0.875 0.19 0.19 1.38
182TC-184TC 2.62 7.25 8.50 1.125 0.25 0.25 1.75
213TC-215TC 3.12 7.25 8.50 1.375 0.31 0.31 2.38
254TC-256TC 3.75 7.25 8.50 1.625 0.38 0.38 2.88
284TC-286TC 4.38 9.00 10.50 1.875 0.50 0.50 3.25

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW Energy $aver®
TEFC-Severe Duty
Dimensions

2.9

Energy $aver® – TEFC-SD

NEMA Frame D 2E 2F BA H N-W U V Min. Key Width Key Thickness Key Length
143T 3.50 5.50 4.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
145T 3.50 5.50 5.00 2.25 0.34 Slot 2.25 0.88 2.00 0.19 0.19 1.38
182T 4.50 7.50 4.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
284TS 7.00 11.00 9.50 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286TS 7.00 11.00 11.00 4.75 0.53 Dia. 3.25 1.62 3.00 0.38 0.38 1.88
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
324TS 8.00 12.50 10.50 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326TS 8.00 12.50 12.00 5.25 0.66 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
364T 9.00 14.00 11.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365T 9.00 14.00 12.25 5.88 0.69 Dia. 5.88 2.38 5.62 0.62 0.62 4.25
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
404T 10.00 16.00 12.25 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
404TS 10.00 16.00 12.25 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
405T 10.00 16.00 13.75 6.62 0.81 Dia. 7.25 2.88 7.00 0.75 0.75 5.62
405TS 10.00 16.00 13.75 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
444T 11.00 18.00 14.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
444TS 11.00 18.00 14.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
445T 11.00 18.00 16.50 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
445TS 11.00 18.00 16.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
447T 11.00 18.00 20.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
447TS 11.00 18.00 20.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
449T 11.00 18.00 25.00 7.50 0.81 Dia. 8.50 3.38 8.25 0.88 0.88 6.88
449TS 11.00 18.00 25.00 7.50 0.81 Dia. 4.75 2.38 4.50 0.63 0.63 3.00
Notes
“C” dimension is overall length and is shown for each catalog number on rating pages.
All dimensions in inches. All dimensions are nominal. Request factory outlines for exact dimensions.
1. Motor base has two sets of holes at 3.00 and 5.00 inches.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Energy $aver®
Kits and Accessories
NEMA 143 to 449T Frames

C-Face Kits - Energy $aver Dripproof

Cat. No. Part No. Frame Poles List Price Price Symbol Norm Stk
A1058 249A9573AAG09 143T-145T 2-4-6 $82 G4-7KITS Y
A1059 249A9573AAG10 182T-184T 2-4-6 $112 G4-7KITS Y
A1060 249A9573AAG11 213T-215T 2-4-6 $138 G4-7KITS Y
A1061 249A9573AAG12 254T-256T 2-4-6 $160 G4-7KITS Y
A1050 249A9573AAG01 284T(S)-286T(S)* 2-4-6 $258 G4-7KITS Y
A1051 249A9573AAG02 324T(S)-326T(S)* 2-4-6 $418 G4-7KITS Y
2.10 A1053 249A9573AAG04 364T-365T 4-6 $539 G4-7KITS Y
A1052 249A9573AAG03 364TS-365TS 2 $539 G4-7KITS Y
A1062 249A9573AAG13 404T(S)* 6 $835 G4-7KITS Y
Energy $aver® – Kits

A1063 249A9573AAG14 405T(S)* 6 $835 G4-7KITS Y

A1055 249A9573AAG06 404T(S)-405T(S)* 4 $857 G4-7KITS Y
A1054 249A9573AAG05 404TS-405TS 2 $725 G4-7KITS Y
A1057 249A9573AAG08 444T(S)-449T(S)* 4-6 $857 G4-7KITS Y
A1056 249A9573AAG07 444TS-445TS 2 $857 G4-7KITS Y
* For use on models with ‘T’ or ‘TS’ type shaft dimensions

C-Face Kits - TEFC-SD

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A1064 249A9573ABG01 143T-145T1 $98 G4-7KITS Y
A1065 249A9573ABG02 182T-184T 1
$134 G4-7KITS Y
A1066 249A9573ABG03 213T-215T1 $167 G4-7KITS Y
A1067 249A9573ABG04 254T-256T1 $224 G4-7KITS Y
A1068 249A9573ABG05 284T-286T1 $297 G4-7KITS Y
A1069 249A9573ABG06 324T(S)-326T(S)1 $441 G4-7KITS Y
A763 249A4321AMG03 364T-365T2 $561 G4-7KITS Y
A764 249A4321AMG04 364TS-365TS2 $561 G4-7KITS Y
A765 249A4321AMG05 404T-405T2 $590 G4-7KITS Y
A766 249A4321AMG06 404TS-405TS2 $590 G4-7KITS Y
A767 249A4321AMG07 444T-449T2 $1,408 G4-7KITS Y
A768 249A4321AMG08 444TS-449TS2 $1,408 G4-7KITS Y
Notes
143-256 frame will not meet NEMA BA dimension using C-Face kit
1. For use on models with ‘BTE’ or ‘STE’ in the motor model code, e.g. 5KE256BTE205 or 5KE256STE205
2. For use on models with ‘LAA’ in the motor model code, e.g. 5KS365LAA205

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Energy $aver®
Kits and Accessories
NEMA 143 to 449T Frames cont.

Sliding Bases for 215-364 Frame Motors

Bases are suitable for the indicated frame size and is suitable for the majority of floor-mounted, belt-connected motors. These
bases are not suitable for ceiling or side-wall mounting installations. The 213-215 frame size bases are closed frame construction
with two adjusting screws. The 254-364 frame size bases are open frame construction with two adjusting screws.

Frame Part No. Cat No. List Price Price Symbol Norm Stk
213 249A9598AA1 A100 $60 GO-1R Y
215 249A9598AA2 A101 $60 GO-1R Y
254 249A9598AA3 A102 $71 GO-1R Y
256 249A9598AA4 A103 $71 GO-1R Y 2.11
284 249A9598AA5 A104 $91 GO-1R Y
286 249A9598AA6 A105 $91 GO-1R Y
324 249A9598AA7 A106 $105 GO-1R Y

Energy $aver® – Kits

326 249A9598AA8 A107 $105 GO-1R Y
364 249A9598AA9 A108 $186 GO-1R Y

Space Heater Kits

Cat No. Frame Volts List Price Price Symbol Norm Stk
A233 182-184 110-120 $107 G4-7KITS N
A239 182-184 220-240 $107 G4-7KITS N
A234 213-326 110-120 $111 G4-7KITS N
A235 213-326 220-240 $111 G4-7KITS N
A236 213-326 440-480 $111 G4-7KITS N
A237 364-405 110-120 $188 G4-7KITS N
A238 364-405 200-208, 220-240 $188 G4-7KITS N
A249 364-405 440-480 $188 G4-7KITS N
A241 444-449 110-120 $203 G4-7KITS Y
A242 444-449 200-208, 220-240 $203 G4-7KITS N
A244 444-449 440-480 $203 G4-7KITS N
Includes insulation and strip heater.
No separate heater nameplate furnished. The existing motor nameplate is to be stamped with heater volts and watts.

Stud Grounding Kit1

Suitable for cast iron, aluminum or steel conduit boxes.
Frame Cat No. List Price Price Symbol Norm Stk
324 TO 405 A300 $158 G6-7KITS N
444 TO 449 A301 $158 G6-7KITS N
1. Each kit contains 2 jam nuts, grounding stud and assembly instructions.

Thermostat Kit
Cat No. Temperature Class Opening Temperature List Price Price Symbol Norm Stk
A337 F 155-165C $89 G4-7KITS N
Thermostat leads are 29 inches long with terminals.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

2.12

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
GEGARD2400 TM
INVERTER
DUTY
TEFC- Extra Severe Duty
EXCEEDS
NEMA
MG1-31
Standard Features
HP Range 0.75-300
Poles 2,4,6,8
Voltage 230/460, 460, 575
Efficiency Meets or exceeds NEMA Premium nominal. Exceeds all NEMA Premium minimum efficiencies.
Frequency 60 Hz (140-449T frame) and 50 Hz (320-449T) rating stamped on nameplate
NEMA Design B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40ºC, Alternate rating 65ºC @ 1.0 SF
Balance/Vibration ISO Grade 1, Ball Bearings: 0.040 in/sec (P)
Roller Bearing: 2P: 0.0003 in (P-P)
4P: 0.0004 in (P-P)
6P: 0.0005 in (P-P)
8P: 0.0007 in (P-P)
Bearing Caps 143-449: Both ends are gasketed.
Bearing Housing Rise 65ºC
Bearing Protection Recessed Slinger, Inpro Seal kit available
Bearing Type Ball, Belted 4-pole 250-300 HP have Roller Brg
Centered Core Allows F1-F2 field conversion
Conduit Box Gasketed and rotatable, Cast iron
Div 2 Temp Codes An optional Division 2 Nameplate or a statement of maximum internal and external surface
temperature can be provided (see kit section).
Drains Stainless Steel T-drains in lowest section of both endshields
End Shield Cast Iron
Fan Non-Sparking Plastic or Bronze
3.1
Fan Cover Cast Iron
Fasteners SAE, Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 inches

X$D ULTRA®
Frame Material Cast Iron
Frame Size 143-449
Grease Polyurea
Ground Ground lug in Conduit Box
Industry Specifications Meets IEEE 45 Marine Duty
Insulation Class Class H for 320 frame & larger, all others Class F with H materials
GEGARD2400TM 320-449 frames. GEGARD2000TM 140-280 frames. Non-Hygroscopic,
Insulation System
Anti-Fungus, 2400Volt or 2000Volt @ .1microsecond rise time. Exceeds NEMA MG1-31
Inverter Capabilities Variable Torque inf:1, Constant Torque 20:1 (see Inverter Duty Capabilities, page vii)
L10 Bearing Life Direct Coupled: 130,000 hrs, Belted: 26,280 hrs, Belted L10a 50,000
Lifting Means 4 Lugs cast into frame
Mounting F1 as Standard and Modifiable to F2
Mounting Holes 1 per foot (324 frame), 2 per foot (all other frames)
Nameplate Stainless Steel Includes Weight, 3/4 Load Efficiency, Vibration Limit, Alternate Ambient and
Service Factor
Paint Buff, Epoxyester
Relubrication Both ends, extended through the fan cover
Rotor Cast Aluminum
1.15, Alternate rating 65°C @ 1.0 SF
Service Factor
1.25 for 320 frames & larger @ 40°C; all other frames 1.15
Shaft TIR Meets IEEE 841, .001 in for shaft diameter 1.625 in and smaller,
.0015 in for shaft diameter greater than 1.625 in.
Tach Mounting Tach kits for field modifications are available
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine Report including Vibration supplied with motor, IEEE 112
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 36 months from date of purchase, 42 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D Ultra®
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY
EXCEEDS
NEMA

Pricing
MG1-31

Volts: 230/460, 460, 575

HP: 0.75 - 300
Nom Guar. Cat List Price C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk Wt (lbs) (in) Notes
0.75 1200 230/460 143T 2.8/1.4 80.0 78.5 M480 $653 G4-7U1 N 43 13.40
0.75 1200 575 143T 1.1 80.0 78.5 M481 $653 G4-7U1 N 43 13.40
0.75 900 230/460 145T 3.8/1.9 72.0 70.0 M460 $901 G4-7U1 N 50 13.40
0.75 900 575 145T 1.5 72.0 70.0 M477 $901 G4-7U1 N 50 13.40
1 3600 230/460 143T 2.8/1.4 87.5 86.5 M462 $618 G4-7U1 N 43 13.40 55
1 3600 575 143T 1.1 87.5 86.5 M463 $618 G4-7U1 N 43 13.40 55
1 1800 230/460 143T 2.8/1.4 86.5 85.5 M482 $559 G4-7U1 Y 43 11.60
1 1800 460 143T 1.4 86.5 85.5 M475 $559 G4-7U1 N 43 11.60
1 1800 575 143T 1.1 86.5 85.5 M483 $559 G4-7U1 N 43 11.60
1 1200 230/460 145T 3.6/1.8 82.5 81.5 M484 $693 G4-7U1 N 50 13.40
1 1200 460 145T 1.8 82.5 81.5 M476 $693 G4-7U1 N 50 13.40
1 1200 575 145T 1.5 82.5 81.5 M485 $693 G4-7U1 N 50 13.40
1 900 230/460 182T 4.4/2.2 80.0 78.5 M9871 $819 G4-7U1 N 76 15.90 55
1 900 460 182T 2.2 80.0 78.5 M9887 $819 G4-7U1 N 76 15.90 55
1 900 575 182T 1.8 80.0 78.5 M9872 $819 G4-7U1 N 76 15.90 55
1.5 3600 230/460 143T 4.0/2.0 87.5 86.5 M486 $649 G4-7U1 N 43 11.60 55
1.5 3600 575 143T 1.6 87.5 86.5 M487 $649 G4-7U1 N 43 11.60 55
1.5 1800 230/460 145T 4.2/2.1 86.5 85.5 M492 $621 G4-7U1 Y 50 11.60
3.2 1.5 1800 460 145T 2.1 86.5 85.5 M464 $621 G4-7U1 N 50 11.60
1.5 1800 575 145T 1.7 86.5 85.5 M493 $621 G4-7U1 N 50 11.60
1.5 1200 230/460 182T 4.8/2.4 87.5 86.5 M9702 $604 G4-7U1 N 76 15.90
1.5 1200 460 182T 2.4 87.5 86.5 M9943 $604 G4-7U1 N 76 15.90
1.5 1200 575 182T 1.9 87.5 86.5 M9703 $604 G4-7U1 N 76 15.90
X$D ULTRA®

1.5 900 230/460 184T 6.4/3.2 80.0 78.5 M9873 $967 G4-7U1 N 101 15.90
1.5 900 460 184T 3.2 80.0 78.5 M9888 $967 G4-7U1 N 101 15.90
1.5 900 575 184T 2.6 80.0 78.5 M9874 $967 G4-7U1 N 101 15.90
2 3600 230/460 145T 5.4/2.7 86.5 85.5 M490 $692 G4-7U1 Y 50 11.60 55
2 3600 460 143T 2.7 86.5 85.5 M465 $692 G4-7U1 N 43 11.60 55
2 3600 575 145T 2.2 86.5 85.5 M491 $692 G4-7U1 N 50 11.60 55
2 1800 230/460 145T 5.4/2.7 86.5 85.5 M488 $684 G4-7U1 Y 50 13.40
2 1800 460 145T 2.7 86.5 85.5 M494 $684 G4-7U1 Y 50 13.40
2 1800 575 145T 2.2 86.5 85.5 M489 $684 G4-7U1 Y 50 13.40
2 1200 230/460 184T 6.0/3.0 88.5 87.5 M9704 $675 G4-7U1 Y 101 15.90
2 1200 460 184T 3.0 88.5 87.5 M9944 $675 G4-7U1 Y 101 15.90
2 1200 575 184T 2.5 88.5 87.5 M9706 $675 G4-7U1 Y 101 15.90
2 900 230/460 213T 7.6/3.8 86.5 85.5 M9875 $1,155 G4-7U1 N 200 20.10
2 900 460 213T 3.8 86.5 85.5 M9705 $1,155 G4-7U1 N 200 20.10
2 900 575 213T 3.0 86.5 85.5 M9876 $1,155 G4-7U1 N 200 20.10
Notes
55 TENV Construction

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
GEGARD2400 TM
INVERTER
DUTY
TEFC- Extra Severe Duty
EXCEEDS
NEMA

Pricing cont.
MG1-31

Volts: 230/460, 460, 575

HP: 0.75 - 300
Nom Guar. Cat List Price C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk Wt (lbs) (in) Notes
3 3600 230/460 182T 7.8/3.9 89.5 88.5 M9713 $600 G4-7U1 Y 76 15.90 55
3 3600 460 182T 3.9 89.5 88.5 M9939 $600 G4-7U1 Y 76 15.90 55
3 3600 575 182T 3.1 89.5 88.5 M9715 $600 G4-7U1 Y 76 15.90 55
3 1800 230/460 182T 8.4/4.2 89.5 88.5 M241 $583 G4-7U1 Y 76 15.90 55
3 1800 460 182T 4.2 89.5 88.5 M9941 $583 G4-7U1 Y 76 15.90 55
3 1800 575 182T 3.3 89.5 88.5 M9711 $583 G4-7U1 Y 76 15.90 55
3 1200 230/460 213T 8.4/4.2 89.5 88.5 M9142 $820 G4-7U1 Y 200 20.10
3 1200 460 213T 4.2 89.5 88.5 M9111 $820 G4-7U1 Y 200 20.10
3 1200 575 213T 3.4 89.5 88.5 M9712 $820 G4-7U1 N 200 20.10
3 900 230/460 215T 10.6/5.3 86.5 85.5 M9877 $1,443 G4-7U1 N 220 20.10
3 900 460 215T 5.3 86.5 85.5 M9708 $1,443 G4-7U1 N 220 20.10
3 900 575 215T 4.3 86.5 85.5 M9878 $1,443 G4-7U1 N 220 20.10
5 3600 230/460 184T 12.4/6.2 90.2 89.5 M240 $712 G4-7U1 Y 101 15.90
5 3600 460 184T 6.2 90.2 89.5 M9940 $712 G4-7U1 Y 101 15.90
5 3600 575 184T 4.9 90.2 89.5 M9722 $712 G4-7U1 Y 101 15.90
5 1800 230/460 184T 13.2/6.6 89.5 88.5 M242 $684 G4-7U1 Y 101 15.90
5 1800 460 184T 6.6 89.5 88.5 M9942 $684 G4-7U1 Y 101 15.90
5 1800 575 184T 5.3 89.5 88.5 M9718 $684 G4-7U1 Y 101 15.90
5 1200 230/460 215T 13.4/6.7 89.5 88.5 M9143 $1,165 G4-7U1 Y 220 20.10 3.3
5 1200 460 215T 6.7 89.5 88.5 M9112 $1,165 G4-7U1 Y 220 20.10
5 1200 575 215T 5.4 89.5 88.5 M9717 $1,165 G4-7U1 N 220 20.10
5 900 230/460 254T 16.0/8.0 89.5 88.5 M9879 $1,917 G4-7U1 N 315 25.60
5 900 460 254T 8.0 89.5 88.5 M9719 $1,917 G4-7U1 N 315 25.60

X$D ULTRA®
5 900 575 254T 6.4 89.5 88.5 M9880 $1,917 G4-7U1 N 315 25.60
7.5 3600 230/460 213T 17.0/8.5 91.0 90.2 M9144 $930 G4-7U1 Y 200 20.10
7.5 3600 460 213T 8.5 91.0 90.2 M990 $930 G4-7U1 Y 200 20.10
7.5 3600 575 213T 6.8 91.0 90.2 M9728 $930 G4-7U1 Y 200 20.10
7.5 1800 230/460 213T 18.2/9.1 91.7 91.0 M9145 $924 G4-7U1 Y 200 20.10
7.5 1800 460 213T 9.1 91.7 91.0 M9911 $924 G4-7U1 Y 200 20.10
7.5 1800 575 213T 7.2 91.7 91.0 M9730 $924 G4-7U1 Y 200 20.10
7.5 1200 230/460 254T 19.6/9.8 91.7 91.0 M9146 $1,547 G4-7U1 N 315 25.60
7.5 1200 460 254T 9.8 91.7 91.0 M9113 $1,547 G4-7U1 Y 315 25.60
7.5 1200 575 254T 7.9 91.7 91.0 M9726 $1,547 G4-7U1 N 315 25.60
7.5 900 230/460 256T 23.2/11.6 89.5 88.5 M9881 $2,423 G4-7U1 N 350 25.60
7.5 900 460 256T 11.6 89.5 88.5 M9724 $2,423 G4-7U1 N 350 25.60
7.5 900 575 256T 9.3 89.5 88.5 M9882 $2,423 G4-7U1 N 350 25.60
Notes
55 TENV Construction

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY
EXCEEDS
NEMA

Pricing cont.
MG1-31

Volts: 230/460, 460, 575

HP: 0.75 - 300
Nom Guar. Cat List Price C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk Wt (lbs) (in) Notes
10 3600 230/460 215T 22.4/11.2 91.0 90.2 M9147 $1,090 G4-7U1 Y 220 20.10
10 3600 460 215T 11.2 91.0 90.2 M991 $1,090 G4-7U1 Y 220 20.10
10 3600 575 215T 9.0 91.0 90.2 M9733 $1,090 G4-7U1 Y 220 20.10
10 1800 230/460 215T 24.0/12.0 91.7 91.0 M9148 $1,031 G4-7U1 Y 220 20.10
10 1800 460 215T 12.0 91.7 91.0 M9912 $1,031 G4-7U1 Y 220 20.10
10 1800 575 215T 9.6 91.7 91.0 M9738 $1,031 G4-7U1 Y 220 20.10
10 1200 230/460 256T 26.0/13.0 91.0 90.2 M9149 $1,898 G4-7U1 N 350 25.60
10 1200 460 256T 13.0 91.0 90.2 M9114 $1,898 G4-7U1 Y 350 25.60
10 1200 575 256T 10.5 91.0 90.2 M9737 $1,898 G4-7U1 N 350 25.60
10 900 230/460 284T 27.4/13.7 90.2 89.5 M9883 $2,828 G4-7U1 N 460 28.58
10 900 460 284T 13.7 90.2 89.5 M9736 $2,828 G4-7U1 N 460 28.58
10 900 575 284T 11.0 90.2 89.5 M9884 $2,828 G4-7U1 N 460 28.58
15 3600 230/460 254T 35.0/17.5 91.7 91.0 M9150 $1,496 G4-7U1 N 315 25.60
15 3600 460 254T 17.5 91.7 91.0 M992 $1,496 G4-7U1 Y 315 25.60
15 3600 575 254T 14.0 91.7 91.0 M9741 $1,496 G4-7U1 Y 315 25.60
15 1800 230/460 254T 36.0/18.0 92.4 91.7 M9151 $1,418 G4-7U1 N 315 34.89
15 1800 460 254T 18.0 92.4 91.7 M9913 $1,418 G4-7U1 Y 315 34.89
15 1800 575 254T 14.4 92.4 91.7 M9745 $1,418 G4-7U1 Y 315 25.60
3.4 15 1200 230/460 284T 39.0/19.5 91.7 91.0 M9152 $2,525 G4-7U1 N 460 28.58
15 1200 460 284T 19.5 91.7 91.0 M9115 $2,525 G4-7U1 Y 460 28.58
15 1200 575 284T 15.6 91.7 91.0 M9746 $2,525 G4-7U1 N 460 28.58
15 900 230/460 286T 40.6/20.3 90.2 89.5 M9885 $3,684 G4-7U1 N 510 28.58
15 900 460 286T 20.3 90.2 89.5 M9742 $3,684 G4-7U1 N 510 28.58
X$D ULTRA®

15 900 575 286T 16.3 90.2 89.5 M9886 $3,684 G4-7U1 N 510 28.58
20 3600 230/460 256T 45.2/22.6 92.4 91.7 M9153 $1,801 G4-7U1 N 350 34.89
20 3600 460 256T 22.6 92.4 91.7 M993 $1,801 G4-7U1 Y 350 34.89
20 3600 575 256T 18.1 92.4 91.7 M9749 $1,801 G4-7U1 N 350 34.89
20 1800 230/460 256T 46.6/23.3 93.0 92.4 M9154 $1,694 G4-7U1 N 350 34.89
20 1800 460 256T 23.3 93.0 92.4 M9914 $1,694 G4-7U1 Y 350 25.60
20 1800 575 256T 18.6 93.0 92.4 M9751 $1,694 G4-7U1 Y 350 25.60
20 1200 230/460 286T 51.6/25.8 91.7 91.0 M9155 $3,083 G4-7U1 N 510 28.58
20 1200 460 286T 25.8 91.7 91.0 M9117 $3,083 G4-7U1 Y 510 28.58
20 1200 575 286T 20.7 91.7 91.0 M9755 $3,083 G4-7U1 N 510 28.58
20 900 460 324T 29.8 91.0 90.2 M9748 $4,504 G4-7U1 N 649 30.54
20 900 575 324T 23.9 91.0 90.2 M8950 $4,504 G4-7U1 N 649 30.54
25 3600 230/460 284TS 55.6/27.8 93.0 92.4 M9156 $2,256 G4-7U1 N 460 27.20
25 3600 460 284TS 27.8 93.0 92.4 M994 $2,256 G4-7U1 Y 460 27.20
25 3600 575 284TS 22.2 93.0 92.4 M9838 $2,256 G4-7U1 Y 460 27.20
25 1800 230/460 284T 59.2/29.6 93.6 93.0 M9157 $2,162 G4-7U1 N 460 28.58
25 1800 460 284T 29.6 93.6 93.0 M9935 $2,162 G4-7U1 Y 460 28.58
25 1800 575 284T 23.7 93.6 93.0 M9759 $2,162 G4-7U1 Y 460 28.58
25 1200 230/460 324T 64.6/32.3 93.0 92.4 M9158 $3,668 G4-7U1 N 679 30.54
25 1200 460 324T 32.3 93.0 92.4 M9119 $3,668 G4-7U1 Y 679 30.54
25 1200 575 324T 25.8 93.0 92.4 M9758 $3,668 G4-7U1 N 679 30.54
25 900 460 326T 37.0 91.0 90.2 M9761 $5,613 G4-7U1 N 710 32.04
25 900 575 326T 29.2 91.0 90.2 M9762 $5,613 G4-7U1 N 710 32.04

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
GEGARD2400 TM
INVERTER
DUTY
TEFC- Extra Severe Duty
EXCEEDS
NEMA
MG1-31

Pricing cont.
Volts: 230/460, 460, 575
HP: 0.75 - 300
Nom Guar. Cat List Price C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk Wt (lbs) (in) Notes
30 3600 230/460 286TS 66.4/33.2 93.0 92.4 M9159 $2,653 G4-7U1 N 510 27.20
30 3600 460 286TS 33.2 93.0 92.4 M995 $2,653 G4-7U1 Y 510 27.20
30 3600 575 286TS 26.7 93.0 92.4 M9828 $2,653 G4-7U1 Y 510 27.20
30 1800 230/460 286T 70.6/35.3 93.6 93.0 M9160 $2,525 G4-7U1 N 510 28.58
30 1800 460 286T 35.3 93.6 93.0 M9937 $2,525 G4-7U1 Y 510 28.58
30 1800 575 286T 28.2 93.6 93.0 M9764 $2,525 G4-7U1 Y 510 28.58
30 1200 230/460 326T 76.4/38.2 93.0 92.4 M9161 $4,184 G4-7U1 N 730 32.04
30 1200 460 326T 38.2 93.0 92.4 M9122 $4,184 G4-7U1 Y 730 32.04
30 1200 575 326T 30.8 93.0 92.4 M9834 $4,184 G4-7U1 N 730 32.04
30 900 460 364T 42.2 92.4 91.7 M9767 $6,564 G4-7U N 1010 34.89
30 900 575 364T 33.8 92.4 91.7 M9766 $6,564 G4-7U N 1010 34.89
40 3600 460 324T 46.8 94.1 93.6 M9820 $3,301 G4-7U1 Y 649 30.54
40 3600 230/460 324TS 93.6/46.8 94.1 93.6 M9162 $3,301 G4-7U1 N 649 29.04
40 3600 460 324TS 46.8 94.1 93.6 M996 $3,301 G4-7U1 Y 649 29.04
40 3600 575 324TS 37.4 94.1 93.6 M9829 $3,301 G4-7U1 Y 649 29.04
40 1800 230/460 324T 101.6/50.8 94.5 94.1 M9163 $3,272 G4-7U1 N 689 30.54
40 1800 460 324T 50.8 94.5 94.1 M9915 $3,272 G4-7U1 Y 689 30.54
40 1800 575 324T 40.6 94.5 94.1 M9768 $3,272 G4-7U1 Y 689 30.54
40 1800 460 324TS 50.8 94.5 94.1 M9916 $3,272 G4-7U1 N 689 29.04 3.5
40 1200 460 364T 49.4 94.1 93.6 M9124 $5,771 G4-7U Y 1030 34.89
40 1200 575 364T 39.8 94.1 93.6 M9835 $5,771 G4-7U N 1030 34.89
40 900 460 365T 55.9 93.0 92.4 M9770 $8,096 G4-7U N 1090 34.89
40 900 575 365T 45.0 93.0 92.4 M9534 $8,096 G4-7U N 1090 34.89

X$D ULTRA®
50 3600 460 326T 57.3 94.5 94.1 M9823 $4,223 G4-7U1 N 700 32.04
50 3600 230/460 326TS 114.6/57.3 94.5 94.1 M9164 $4,223 G4-7U1 N 700 30.48
50 3600 460 326TS 57.3 94.5 94.1 M997 $4,223 G4-7U1 Y 700 30.48
50 3600 575 326TS 45.5 94.5 94.1 M9839 $4,223 G4-7U1 N 700 30.48
50 1800 230/460 326T 127.8/63.9 94.5 94.1 M9165 $3,836 G4-7U1 N 740 32.04
50 1800 460 326T 63.9 94.5 94.1 M9917 $3,836 G4-7U1 Y 740 32.04
50 1800 575 326T 51.1 94.5 94.1 M9765 $3,836 G4-7U1 Y 740 32.04
50 1800 460 326TS 63.9 94.5 94.1 M9918 $3,836 G4-7U1 N 740 30.48
50 1200 460 365T 62.2 94.1 93.6 M9126 $6,700 G4-7U Y 1070 34.89
50 1200 575 365T 49.7 94.1 93.6 M9775 $6,700 G4-7U N 1070 34.89
50 900 460 404T 66.6 93.0 92.4 M9773 $9,769 G4-7U N 1490 39.77
50 900 575 404T 53.0 93.0 92.4 M9535 $9,769 G4-7U N 1490 39.77

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY
EXCEEDS
NEMA
MG1-31

Pricing cont.
Volts: 230/460, 460, 575
HP: 0.75 - 300
Nom Guar. Cat List Price Norm C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Stk Wt (lbs) (in) Notes
60 3600 460 364TS 70.4 95.0 94.5 M998 $5,877 G4-7U Y 940 32.76
60 3600 575 364TS 56.3 95.0 94.5 M9847 $5,877 G4-7U N 940 32.76
60 1800 460 364T 71.2 95.0 94.5 M9919 $5,755 G4-7U Y 1020 34.89
60 1800 575 364T 56.6 95.0 94.5 M9776 $5,755 G4-7U Y 1020 34.89
60 1800 460 364TS 71.2 95.0 94.5 M9921 $5,755 G4-7U N 1020 32.76
60 1200 460 404T 72.5 95.0 94.5 M9128 $7,794 G4-7U Y 1480 39.77
60 1200 575 404T 58.0 95.0 94.5 M9837 $7,794 G4-7U N 1480 39.77
60 900 460 405T 78.9 93.0 92.4 M9778 $12,000 G4-7U N 1570 39.77
60 900 575 405T 63.1 93.0 92.4 M9536 $12,000 G4-7U N 1570 39.77
75 3600 460 365TS 90.4 95.8 95.4 M999 $7,215 G4-7U Y 970 32.76
75 3600 575 365TS 72.3 95.8 95.4 M9830 $7,215 G4-7U N 970 32.76
75 1800 460 365T 87.1 95.4 95.0 M9922 $6,977 G4-7U Y 1080 34.89
75 1800 575 365T 69.7 95.4 95.0 M9781 $6,977 G4-7U Y 1080 34.89
75 1800 460 365TS 87.1 95.4 95.0 M9923 $6,977 G4-7U N 1080 32.76
75 1200 460 405T 89.6 95.0 94.5 M9131 $8,664 G4-7U Y 1540 39.77
75 1200 575 405T 71.2 95.0 94.5 M9868 $8,664 G4-7U Y 1540 39.77
75 900 460 444T 94.0 94.5 94.1 M9780 $15,015 G4-7U N 1950 45.62
75 900 575 444T 75.2 94.5 94.1 M9537 $15,015 G4-7U N 1950 45.62
3.6 100 3600 460 405TS 108.0 95.4 95.0 M9510 $9,342 G4-7U N 1530 36.76 66
100 3600 460 405TS 108.0 95.4 95.0 M9992 $9,342 G4-7U N 1530 36.76 62
100 3600 575 405TS 86.3 95.4 95.0 M9831 $9,342 G4-7U Y 1530 36.76 66
100 1800 460 405T 119.0 95.8 95.4 M9924 $8,617 G4-7U Y 1480 39.77
100 1800 575 405T 95.3 95.8 95.4 M9779 $8,617 G4-7U Y 1480 39.77
X$D ULTRA®

100 1800 460 405TS 119.0 95.8 95.4 M9925 $8,617 G4-7U N 1480 36.76
100 1200 460 444T 116.0 95.4 95.0 M9133 $11,669 G4-7U Y 2060 45.62
100 1200 575 444T 93.4 95.4 95.0 M9846 $11,669 G4-7U Y 2060 45.62
100 900 460 445T 125.0 94.5 94.1 M9782 $19,025 G4-7U N 2020 45.62
100 900 575 445T 100.0 94.5 94.1 M8953 $19,025 G4-7U N 2020 45.62
125 3600 460 444TS 139.0 95.4 95.0 M9511 $12,203 G4-7U N 1790 41.87 66
125 3600 460 444TS 139.0 95.4 95.0 M9993 $12,203 G4-7U Y 1790 41.87 62
125 3600 575 444TS 112.0 95.4 95.0 M9538 $12,203 G4-7U Y 1790 41.87 66
125 1800 460 444T 144.0 95.8 95.4 M9926 $11,337 G4-7U Y 1970 45.62
125 1800 575 444T 115.0 95.8 95.4 M9832 $11,337 G4-7U Y 1970 45.62
125 1800 460 444TS 144.0 95.8 95.4 M9927 $11,337 G4-7U N 1970 41.87
125 1200 460 445T 150.0 95.4 95.0 M9135 $14,057 G4-7U Y 2130 45.62
125 1200 575 445T 120.0 95.4 95.0 M9870 $14,057 G4-7U N 2130 45.62
125 900 460 447T 155.0 95.0 94.5 M9784 $21,185 G4-7U N 2580 52.12
125 900 575 447T 124.0 95.0 94.5 M8954 $21,185 G4-7U N 2580 52.12
Notes
62 Connected for CCW rotation facing opposite shaft end. No reconnection possible.
66 CW rotation only facing opposite drive-end. CCW rotation available, but must be specified on the order.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
GEGARD2400 TM
INVERTER
DUTY
TEFC- Extra Severe Duty
EXCEEDS
NEMA
MG1-31

Pricing cont.
Volts: 230/460, 460, 575
HP: 0.75 - 300
Nom Guar. Cat List Price Norm C Dim
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Stk Wt (lbs) (in) Notes
150 3600 460 445TS 165.0 95.8 95.4 M9512 $14,674 G4-7U N 1860 41.87 66
150 3600 460 445TS 165.0 95.8 95.4 M9994 $14,674 G4-7U N 1860 41.87 62
150 3600 575 445TS 132.0 95.8 95.4 M8955 $14,674 G4-7U N 1860 41.87 66
150 1800 460 445T 170.0 96.2 95.8 M9928 $13,190 G4-7U Y 2090 45.62
150 1800 575 445T 137.0 96.2 95.8 M9854 $13,190 G4-7U Y 2060 45.62
150 1800 460 445TS 170.0 96.2 95.8 M9929 $13,190 G4-7U Y 2090 41.87
150 1200 460 447T 171.0 95.8 95.4 M9137 $17,030 G4-7U Y 2860 52.12
150 1200 575 447T 137.0 95.8 95.4 M9869 $17,030 G4-7U Y 2860 52.12
150 900 460 449T 184.0 95.0 94.5 M9785 $23,102 G4-7U Y 3150 52.12
150 900 575 449T 147.0 95.0 94.5 M8956 $23,102 G4-7U N 3120 52.12
200 3600 460 447TS 214.0 95.8 95.4 M9961 $18,577 G4-7U N 2560 50.37 66
200 3600 460 447TS 214.0 95.8 95.4 M9995 $18,577 G4-7U N 2560 50.37 62
200 3600 575 447TS 170.0 95.8 95.4 M8957 $18,577 G4-7U N 2560 50.37 66
200 1800 460 447T 222.0 96.5 96.2 M9991 $16,545 G4-7U Y 2610 52.12 98
200 1800 460 447T 222.0 96.5 96.2 M9958 $16,545 G4-7U Y 2610 52.12
200 1800 575 447T 177.0 96.5 96.2 M9959 $16,545 G4-7U Y 2610 52.12
200 1200 460 449LL 229.0 95.8 95.4 M9141 $19,053 G4-7U N 3070 54.12
200 1200 460 449T 229.0 95.8 95.4 M9139 $19,053 G4-7U Y 3070 52.12
200 1200 575 449T 183.0 95.8 95.4 M9845 $19,053 G4-7U Y 3070 52.12 3.7
250 3600 460 449TS 265.0 95.8 95.4 M9514 $23,935 G4-7U N 2770 50.37 66
250 3600 460 449TS 265.0 95.8 95.4 M9996 $23,935 G4-7U N 2770 50.37 62
250 3600 575 449TS 211.0 95.8 95.4 M8959 $23,935 G4-7U N 2770 50.37 66
250 1800 460 449T 276.0 96.5 96.2 M9988 $19,347 G4-7U Y 3010 54.12

X$D ULTRA®
250 1800 460 449T 280.0 96.2 95.8 M9933 $19,347 G4-7U Y 2790 54.12 98
250 1800 575 449T 218.0 96.5 96.2 M9989 $19,347 G4-7U N 3010 54.12
250 1800 575 449T 224.0 96.2 95.8 M9851 $19,347 G4-7U N 2790 54.12 98
250 1200 460 449T 296.0 95.8 95.4 M8963 $24,120 G4-7U N 3150 54.12
300 3600 460 449TS 319.0 95.8 95.4 M8960 $29,681 G4-7U N 2790 50.37 66
300 3600 575 449TS 255.0 95.8 95.4 M8961 $29,681 G4-7U N 2790 50.37 66
300 1800 460 449T 334.0 96.2 95.8 M9990 $22,654 G4-7U Y 2980 54.12
300 1800 460 449T 334.0 96.2 95.8 M9906 $22,654 G4-7U Y 2980 54.12 98
300 1800 575 449T 265.0 96.5 96.2 M8962 $22,654 G4-7U N 3030 54.12 98
Notes
62 Connected for CCW rotation facing opposite shaft end. No reconnection possible.
66 CW rotation only facing opposite drive-end. CCW rotation available, but must be specified on the order.
98 For belted load only. Roller Bearing on drive-end.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY

C-Face EXCEEDS
NEMA
MG1-31

Pricing

Volts: 230/460, 460

HP: 0.75 - 50
Nom Guar. Cat List Price Wt
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) C Dim (in) Notes
0.75 1200 230/460 143TC 2.8/1.4 80.0 78.5 M496 $722 G4-7U1 N 43 13.92
1 1800 230/460 143TC 2.8/1.4 86.5 85.5 M497 $628 G4-7U1 Y 43 13.92
1 1800 460 143TC 1.4 86.5 85.5 M478 $680 G4-7U1 N 43 13.92
1 1200 230/460 145TC 3.6/1.8 82.5 81.5 M498 $762 G4-7U1 N 50 13.92
1.5 1800 230/460 145TC 4.2/2.1 86.5 85.5 M499 $690 G4-7U1 Y 50 13.92
1.5 1800 460 145TC 2.1 86.5 85.5 M479 $690 G4-7U1 N 50 13.92
1.5 1200 460 182TC 2.4 87.5 86.5 M9946 $684 G4-7U1 N 76 16.65
2 1800 230/460 145TC 5.4/2.7 86.5 85.5 M500 $753 G4-7U1 Y 50 13.92
2 1200 460 184TC 3.0 88.5 87.5 M9948 $755 G4-7U1 N 101 16.65
3 3600 460 182TC 3.9 89.5 88.5 M9945 $680 G4-7U1 Y 76 16.65 55
3 1800 460 182TC 4.2 89.5 88.5 M9889 $663 G4-7U1 Y 76 16.65 55
3 1200 460 213TC 4.2 89.5 88.5 M9950 $900 G4-7U1 Y 200 20.90
5 3600 460 184TC 6.2 90.2 89.5 M9947 $792 G4-7U1 Y 101 16.65
5 1800 460 184TC 6.6 89.5 88.5 M9890 $764 G4-7U1 Y 101 16.65
5 1200 460 215TC 6.7 89.5 88.5 M9952 $1,245 G4-7U1 Y 220 20.90
7.5 3600 460 213TC 8.5 91.0 90.2 M9949 $1,010 G4-7U1 Y 200 20.90
3.8 7.5 1800 460 213TC 9.1 91.7 91.0 M9891 $1,004 G4-7U1 Y 200 20.90
7.5 1200 460 254TC 9.8 91.7 91.0 M9954 $1,651 G4-7U1 N 315 26.09
10 3600 460 215TC 11.2 91.0 90.2 M9951 $1,170 G4-7U1 Y 220 20.90
10 1800 460 215TC 12.0 91.7 91.0 M9892 $1,111 G4-7U1 Y 220 20.60
X$D ULTRA® C-Face

10 1200 460 256TC 13.0 91.0 90.2 M9956 $2,002 G4-7U1 N 350 26.09
15 3600 460 254TC 17.5 91.7 91.0 M9953 $1,905 G4-7U1 Y 315 26.09
15 1800 460 254TC 18.0 92.4 91.7 M9893 $1,522 G4-7U1 Y 315 26.09
15 1200 460 284TC 19.5 91.7 91.0 M9901 $2,672 G4-7U1 Y 460 28.58
20 3600 460 256TC 22.6 92.4 91.7 M9955 $1,905 G4-7U1 N 350 26.09
20 1800 460 256TC 23.3 93.0 92.4 M9894 $1,798 G4-7U1 Y 350 26.09
20 1200 460 286TC 25.8 91.7 91.0 M9902 $3,230 G4-7U1 N 510 28.58
25 3600 460 284TSC 27.8 93.0 92.4 M9903 $2,403 G4-7U1 N 460 27.20
25 1800 460 284TC 29.6 93.6 93.0 M9895 $2,309 G4-7U1 N 460 28.58
30 3600 460 286TSC 33.2 93.0 92.4 M9904 $2,800 G4-7U1 N 510 27.20
30 1800 460 286TC 35.3 93.6 93.0 M9896 $2,671 G4-7U1 N 510 28.58
40 3600 460 324TSC 46.3 94.1 93.6 M8964 $3,514 G4-7U1 N 649 29.04
40 1800 460 324TC 49.8 94.5 94.1 M8965 $3,485 G4-7U1 N 689 30.54
50 3600 460 326TSC 56.9 94.5 94.1 M8966 $4,436 G4-7U1 N 700 30.48
50 1800 460 326TC 62.3 94.5 94.1 M8967 $4,109 G4-7U1 N 740 32.04
Notes
55 TENV Construction

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
GEGARD2400 TM
INVERTER
DUTY
TEFC- Extra Severe Duty
NEMA Design C – High Torque
EXCEEDS
NEMA
MG1-31

Pricing

Volts: 460
HP: 40 - 300
Starting Breakdown
Nom Guar. Cat List Price Wt C Dim Torque Torque
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) (in) (lb-ft) (lb-ft) Notes
40 1200 460 364T 50.6 93.0 92.4 M8982 $7,439 G4-7UC N 1000 34.89 443 454 98
50 1200 460 365T 63.3 93.0 92.4 M8983 $8,507 G4-7UC N 1030 34.89 551 553 98
60 1800 460 364T 72.5 94.5 94.1 M8992 $7,420 G4-7UC N 1030 34.89 456 422 98
60 1200 460 404T 73.2 94.1 93.6 M8984 $9,999 G4-7UC N 1480 39.77 590 625 98
75 1800 460 365T 89.5 94.5 94.1 M8993 $8,826 G4-7UC N 1090 34.89 594 521 98
75 1200 460 405T 91.0 94.1 93.6 M8985 $11,000 G4-7UC N 1530 39.77 742 782 98
100 1800 460 405T 118.0 95.4 95.0 M8994 $10,946 G4-7UC N 1500 39.77 700 679 98
100 1200 460 444T 123.0 93.0 92.4 M8986 $14,854 G4-7UC N 1920 45.62 1118 1032 98
125 1800 460 444T 145.0 95.8 95.4 M8995 $14,473 G4-7UC N 1970 45.62 762 924 98
150 1800 460 445T 173.0 95.8 95.4 M8996 $16,604 G4-7UC Y 2060 45.62 1105 1083 98
150 1200 460 447T 185.0 94.5 94.1 M8988 $21,313 G4-7UC N 2700 54.12 1420 1486 98
200 1800 460 447T 229.0 95.8 95.4 M8997 $20,755 G4-7UC Y 2700 54.12 1662 1503 98
200 1200 460 449T 243.0 95.0 94.5 M8989 $23,639 G4-7UC N 3070 54.12 2433 2159 98
250 1800 460 449T 282.0 95.8 95.4 M8998 $23,135 G4-7UC Y 2980 54.12 2137 1843 98
300 1800 460 449T 338.0 95.4 95.0 M8999 $26,938 G4-7UC N 3100 54.12 2116 2054 98
Notes 3.9
98 For belted load only. Roller bearing on drive-end.

X$D ULTRA® - High Torque

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty
Typical Performance Data
Volts: 460
HP: 0.75 - 300
NP Eff 75% 50% NP PF 75% Load 50% Load
NP Design NEMA B Code FLT LRT BDT Full Guar. Eff. Load Load Full Power Power Max
HP FL RPM FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Full Load Eff Eff Load Factor Factor KVAR
0.75 1150 1.4 7.5 12.5 P 3.4 9.7 12.3 80.0 78.5 81.4 78.7 63.5 54.4 41.9 0.6
0.75 850 1.9 7.2 12.5 P 4.6 11.6 14.9 72.0 70.0 72.2 67.4 52.5 43.7 33.4 1.0
1 1750 1.4 11.7 15.0 N 3.0 12.0 14.4 86.5 85.5 87.1 85.1 76.0 68.0 55.0 0.5
1 1155 1.8 10.8 15.0 N 4.6 14.6 18.1 82.5 81.5 83.4 80.9 62.5 53.5 41.1 0.8
1 875 2.2 10.5 15.0 N 6.0 11.0 19.3 80.0 78.5 79.6 75.6 52.5 43.9 33.3 1.2
1.5 1740 2.1 16.6 20.0 M 4.5 17.4 20.4 86.5 85.5 87.6 86.3 77.5 69.9 56.9 0.8
1.5 1175 2.4 17.1 20.0 M 6.7 14.3 29.0 87.5 86.5 88.3 86.5 68.0 59.6 46.8 1.0
1.5 870 3.2 14.8 20.0 M 9.0 16.7 26.7 80.0 78.5 80.5 77.1 55.5 46.7 35.6 1.6
2 3515 2.7 23.9 25.0 L 3.0 9.2 12.0 86.5 85.5 89.2 88.6 80.5 73.2 60.4 0.8
2 1730 2.7 20.5 25.0 L 6.1 22.0 25.4 86.5 85.5 88.0 87.3 80.0 72.9 60.2 0.9
2 1170 3 22.2 25.0 L 9.0 19.2 37.8 88.5 87.5 88.8 87.4 69.5 61.4 48.6 1.2
2 880 3.8 20.5 25.0 L 11.9 21.6 38.2 86.5 85.5 85.8 83.2 57.0 48.9 37.4 1.9
3 3530 3.8 26.3 32.0 K 4.5 9.4 14.3 89.5 88.5 91.4 90.8 82.0 76.5 65.2 1.0
3 1760 4.2 29.3 32.0 K 8.9 22.7 30.1 89.5 88.5 89.8 88.8 75.5 68.7 56.2 1.5
3 1180 4.2 30.6 32.0 K 13.4 32.3 44.4 89.5 88.5 89.8 88.6 74.0 67.0 54.5 1.6
3 875 5.3 27.8 32.0 K 18.0 31.3 50.8 86.5 85.5 86.4 84.8 61.0 53.1 41.3 2.5
5 3540 6.2 45.7 46.0 J 7.4 17.9 25.2 90.2 89.5 91.3 90.3 84.0 79.3 69.2 1.5
3.10 5 1755 6.6 43.1 46.0 J 15.0 34.4 43.8 89.5 88.5 90.5 90.1 79.5 74.2 63.4 2.0
5 1170 6.7 43.8 46.0 J 22.4 48.4 63.5 89.5 88.5 90.6 90.3 78.0 72.7 61.5 2.2
X$D ULTRA® - Performance Data

5 880 8.0 43.2 46.0 J 29.8 47.6 83.3 89.5 88.5 89.7 88.2 65.0 56.8 44.3 3.5
7.5 3535 8.5 61.7 63.5 H 11.1 23.7 31.5 91.0 90.2 91.4 90.7 90.5 88.6 82.8 1.6
7.5 1770 9.1 61.2 63.5 H 22.3 41.5 61.3 91.7 91.0 92.1 91.7 84.5 81.6 73.4 2.2
7.5 1175 9.8 60.6 63.5 H 33.5 61.9 92.0 91.7 91.0 92.0 91.6 78.5 73.0 62.1 2.9
7.5 880 11.5 58.9 63.5 H 44.8 67.8 113.6 89.5 88.5 90.2 89.3 68.0 60.5 47.9 4.6
10 3525 11.2 76.3 81.0 H 14.9 31.2 38.5 91.0 90.2 91.9 91.8 92.0 90.6 86.5 1.8
10 1765 12.0 78.3 81.0 H 29.7 54.3 78.5 91.7 91.0 92.3 92.2 85.0 82.1 74.3 2.9
10 1170 13.0 77.6 81.0 H 44.8 81.1 119.2 91.0 90.2 91.7 91.6 79.0 73.7 62.9 3.9
10 885 13.7 76.3 81.0 H 59.5 77.8 147.4 90.2 89.5 91.2 91.2 75.5 70.1 59.2 4.2
15 3555 17.5 106.5 116.0 G 22.2 39.1 50.3 91.7 91.0 92.5 92.2 87.5 86.1 80.9 2.8
15 1770 18.0 108.4 116.0 G 44.5 96.4 111.3 92.4 91.7 93.1 93.0 84.5 81.1 72.4 4.3
15 1185 19.5 107.8 116.0 G 66.6 98.8 160.8 91.7 91.0 92.5 92.2 78.5 73.5 62.7 5.8
15 880 20.3 112.6 116.0 G 89.5 122.4 223.0 90.2 89.5 91.3 91.6 76.5 71.6 61.1 5.9
20 3550 22.6 136.7 145.0 G 29.6 59.2 61.7 92.4 91.7 93.5 93.5 89.5 89.6 87.2 2.5
20 1770 23.3 137.0 145.0 G 59.4 129.1 140.7 93.0 92.4 93.7 93.9 86.5 84.2 77.4 4.7
20 1180 25.8 139.9 145.0 G 88.9 131.0 210.1 91.7 91.0 92.7 92.7 79.0 74.4 64.0 7.4
20 875 29.8 136.5 145.0 G 119.8 189.3 261.3 91.0 90.2 91.8 91.2 69.0 60.6 48.9 11.4

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
TEFC- Extra Severe Duty
Typical Performance Data cont.
Volts: 460
HP: 0.75 - 300
NP Eff 75% 50% NP PF 75% Load 50% Load
NP Design NEMA B Code FLT LRT BDT Full Guar. Eff. Load Load Full Power Power Max
HP FL RPM FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Full Load Eff Eff Load Factor Factor KVAR
25 3555 27.8 172.9 182.5 G 36.9 88.4 89.5 93.0 92.4 93.4 93.1 90.5 89.6 85.4 3.9
25 1775 29.6 164.9 182.5 G 73.9 134.4 165.5 93.6 93.0 94.2 94.0 84.5 81.5 73.2 6.9
25 1180 32.3 168.8 182.5 G 111.4 204.2 253.6 93.0 92.4 93.3 92.9 78.0 71.9 61.5 9.7
25 875 37.0 166.4 182.5 G 150.0 235.3 319.7 91.0 90.2 91.9 91.4 69.5 61.7 50.2 13.7
30 3550 33.2 205.3 217.5 G 44.4 108.1 106.0 93.0 92.4 93.6 93.5 91.0 89.8 85.9 4.5
30 1775 35.1 191.6 217.5 G 88.7 158.7 192.3 93.6 93.0 94.3 94.3 85.0 82.4 74.7 7.8
30 1175 38.2 201.3 217.5 G 133.8 252.2 302.6 93.0 92.4 93.6 93.3 79.0 72.9 62.8 11.1
30 890 42.2 188.5 217.5 G 177.2 243.3 384.3 92.4 91.7 93.9 93.3 72.0 64.1 52.4 15.1
40 3575 46.8 276.8 290.0 G 58.8 94.1 148.9 94.1 93.6 94.0 92.9 85.0 77.3 68.0 12.0
40 1785 50.8 279.9 290.0 G 117.8 205.5 273.4 94.5 94.1 94.5 93.9 78.0 71.1 60.0 16.4
40 1185 49.4 270.9 290.0 G 176.9 274.0 441.1 94.1 93.6 94.6 94.2 80.5 73.9 63.3 14.8
40 890 55.9 254.2 290.0 G 236.4 336.8 518.3 93.0 92.4 94.1 93.5 72.0 64.3 52.5 20.1
50 3570 57.3 342.7 362.5 G 73.5 126.7 183.2 94.5 94.1 94.6 93.8 86.5 80.0 71.6 13.2
50 1780 63.9 341.0 362.5 G 147.4 256.1 332.2 94.5 94.1 94.6 94.1 77.5 70.7 59.7 20.6
50 1185 62.2 333.3 362.5 G 221.3 344.7 543.6 94.1 93.6 94.7 94.5 80.0 73.9 63.3 18.4
50 885 66.6 340.5 362.5 G 297.3 455.4 768.9 93.0 92.4 94.2 93.8 75.5 68.0 56.2 22.8
60 3570 70.4 376.7 435.0 G 88.3 116.7 207.4 95.0 94.5 94.8 93.9 84.0 76.2 66.7 18.4
60 1780 71.2 407.3 435.0 G 177.1 359.6 443.2 95.0 94.5 95.1 94.7 83.0 77.6 67.9 19.5 3.11
60 1190 72.5 401.9 435.0 G 264.3 383.8 607.8 95.0 94.5 95.1 94.6 81.5 76.2 66.4 20.1

X$D ULTRA® - Performance Data

60 885 78.9 409.1 435.0 G 356.8 560.0 927.6 93.0 92.4 94.5 94.2 76.5 68.7 57.1 26.5
75 3570 83.3 508.9 542.5 G 110.3 170.1 274.7 93.6 93.0 94.9 94.0 83.0 74.7 64.4 24.9
75 1785 87.1 515.0 542.5 G 220.8 345.9 554.2 95.4 95.0 95.6 95.4 84.5 79.9 71.0 21.8
75 1190 89.6 483.8 542.5 G 330.5 477.3 730.0 95.0 94.5 95.4 95.0 82.5 77.7 68.7 23.1
75 890 94.0 482.2 542.5 G 442.2 616.5 1019.6 94.5 94.1 95.2 94.7 79.0 73.1 62.9 27.6
100 3570 108.0 707.2 725.0 G 147.0 241.5 384.8 95.4 95.0 95.7 95.5 91.0 87.1 82.0 17.4
100 1785 119.0 587.6 725.0 G 293.9 427.5 668.7 95.8 95.4 96.0 95.8 82.0 76.7 67.0 32.9
100 1195 116.0 684.8 725.0 G 440.2 590.2 1070.7 95.4 95.0 95.4 94.8 84.5 79.6 71.0 29.0
100 890 125.0 644.3 725.0 G 590.0 848.7 1371.3 94.5 94.1 95.3 94.9 79.0 72.9 62.7 37.0
125 3580 139.0 809.4 907.5 G 183.3 220.9 474.2 95.4 95.0 95.8 95.3 88.0 82.0 74.3 29.9
125 1780 144.0 723.1 907.5 G 368.4 625.3 865.9 95.8 95.4 95.8 95.4 85.0 80.9 72.8 34.2
125 1190 150.0 850.7 907.5 G 550.7 977.6 1296.8 95.4 95.0 95.5 95.0 81.5 76.2 66.5 41.6
125 890 155.0 829.6 907.5 G 737.7 1125.9 1813.5 95.0 94.5 95.4 95.1 79.5 73.5 63.5 45.0
150 3580 166.0 985.2 1085.0 G 220.0 289.4 571.5 95.8 95.4 96.1 95.7 89.0 83.4 76.4 33.2
150 1790 170.0 1033.2 1085.0 G 439.7 523.1 1157.0 96.2 95.8 96.5 96.1 86.0 81.6 73.2 40.7
150 1195 171.0 1030.6 1085.0 G 660.4 1001.9 1755.9 95.8 95.4 95.8 95.5 85.5 81.1 73.0 40.2
150 890 184.0 978.0 1085.0 G 885.0 1338.5 2104.7 95.0 94.5 95.8 95.6 80.5 75.3 65.9 49.4
200 3580 214.0 1320.7 1450.0 G 293.3 430.9 816.9 95.8 95.4 95.8 95.3 91.5 88.3 84.1 31.5
200 1790 222.0 1193.4 1450.0 G 586.6 629.2 1369.7 96.5 96.2 96.6 96.4 87.5 84.5 78.1 44.3
200 1190 229.0 1343.0 1450.0 G 881.0 1343.4 2293.5 95.8 95.4 96.0 95.8 85.5 81.6 73.8 51.7
250 3575 265.0 1556.9 1825.0 G 366.9 561.2 949.0 95.8 95.4 96.1 95.9 92.0 89.8 86.9 32.6
250 1790 272.0 1523.4 1825.0 G 733.1 860.6 1715.0 96.5 96.2 96.7 96.7 89.0 86.5 81.1 48.5
250 1195 296.0 1706.6 1825.0 G 1100.5 1390.8 2955.9 95.8 95.4 96.0 95.9 82.5 77.1 67.6 79.9
300 3580 319.0 2100.2 2200.0 G 440.0 717.7 1260.4 95.8 95.4 96.4 96.1 92.0 88.9 84.8 45.5
300 1790 334.0 2000.6 2200.0 G 879.3 1121.1 2245.2 96.2 95.8 96.3 95.9 87.5 84.2 77.3 69.5

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty
Typical Performance Data
Volts: 575
HP: 0.75 - 300
NP Eff Guar. 75% 50% NP PF 75% Load 50% Load
Design NEMA B Code FLT LRT BDT Full Eff. Full Load Load Full Power Power Max
HP FL RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff Eff Load Factor Factor KVAR
0.75 1150 1.1 5.9 10.0 P 3.4 9.5 12.0 80.0 78.5 81.6 79.0 64.0 55.1 42.6 0.6
0.75 850 1.5 5.8 10.0 P 4.6 11.6 15.0 72.0 70.0 72.0 67.2 52.0 43.5 33.2 1.0
1 1750 1.1 9.4 12.0 N 3.0 12.0 14.5 86.5 85.5 87.0 85.0 75.5 67.6 54.6 0.5
1 1155 1.5 8.9 12.0 N 4.5 15.1 18.7 82.5 81.5 83.1 80.3 61.5 52.3 40.0 0.9
1 875 1.8 8.6 12.0 N 6.0 11.2 19.5 80.0 78.5 79.3 75.2 52.0 43.6 33.0 1.2
1.5 1740 1.7 13.5 16.0 M 4.5 17.9 20.9 86.5 85.5 87.8 86.4 77.5 69.5 56.5 0.8
1.5 1175 1.9 13.9 16.0 M 6.7 14.5 29.4 87.5 86.5 88.3 86.4 67.5 59.2 46.4 1.0
1.5 870 2.6 12.5 16.0 M 9.0 18.0 28.1 80.0 78.5 80.5 76.9 54.0 45.2 34.3 1.7
2 3515 2.2 19.0 20.0 L 3.0 9.2 11.9 86.5 85.5 89.2 88.6 80.5 73.5 60.8 0.8
2 1730 2.2 16.5 20.0 L 6.1 22.1 25.5 86.5 85.5 88.0 87.2 80.0 72.7 60.0 0.9
2 1170 2.5 19.0 20.0 L 9.0 20.8 40.5 88.5 87.5 88.8 87.2 68.0 59.4 46.5 1.3
2 880 3 16.1 20.0 L 11.9 21.0 37.4 86.5 85.5 85.8 83.3 57.5 49.4 37.9 1.9
3 3530 3.1 21.0 25.6 K 4.5 9.4 14.2 89.5 88.5 91.3 90.8 82.0 76.5 65.3 1.0
3 1760 3.3 23.5 25.6 K 8.9 22.7 30.2 89.5 88.5 89.7 88.8 75.5 68.5 56.0 1.5
3 1180 3.4 25.3 25.6 K 13.4 33.4 45.8 89.5 88.5 89.7 88.4 73.0 65.8 53.2 1.7
3 875 4.3 22.7 25.6 K 18.0 32.2 51.9 86.5 85.5 86.3 84.6 60.5 52.6 40.7 2.5
5 3540 4.9 36.0 36.8 J 7.4 17.5 24.6 90.2 89.5 91.1 90.2 84.5 79.7 69.7 1.5
3.12 5 1755 5.3 34.4 36.8 J 15.0 34.3 43.8 89.5 88.5 90.5 90.1 79.5 74.3 63.5 2.0
5 1170 5.4 35.8 36.8 J 22.4 49.5 64.8 89.5 88.5 90.6 90.2 77.5 72.1 60.6 2.2
X$D ULTRA® - Performance Data

5 880 6.4 35.0 36.8 J 29.8 48.1 83.9 89.5 88.5 89.4 87.8 65.0 56.4 43.8 3.5
7.5 3535 6.8 48.1 50.8 H 11.1 23.0 30.7 91.0 90.2 91.4 90.8 91.0 89.0 83.5 1.6
7.5 1770 7.2 48.2 50.8 H 22.3 40.8 60.4 91.7 91.0 92.1 91.7 85.0 81.9 73.9 2.2
7.5 1175 7.8 48.5 50.8 H 33.5 62.0 92.2 91.7 91.0 92.1 91.6 78.5 73.0 62.1 2.9
7.5 880 9.2 47.1 50.8 H 44.8 67.7 113.4 89.5 88.5 90.1 89.3 68.0 60.5 47.9 4.6
10 3525 9 61.5 64.8 H 14.9 31.4 38.9 91.0 90.2 91.9 91.8 91.5 90.6 86.3 1.8
10 1765 9.6 62.7 64.8 H 29.7 54.3 78.6 91.7 91.0 92.3 92.2 85.0 82.0 74.2 2.9
10 1170 10.5 62.9 64.8 H 44.8 82.1 120.6 91.0 90.2 91.7 91.5 78.5 73.4 62.4 3.9
10 885 11 60.8 64.8 H 59.5 77.1 146.4 90.2 89.5 91.1 91.0 75.5 70.2 59.3 4.2
15 3555 14 84.8 92.8 G 22.2 38.9 50.0 91.7 91.0 92.5 92.2 87.5 86.1 81.0 2.8
15 1770 14.4 85.6 92.8 G 44.5 95.0 109.9 92.4 91.7 93.0 93.0 84.5 81.4 72.8 4.3
15 1180 15.6 84.9 92.8 G 66.6 97.4 158.6 91.7 91.0 92.5 92.3 78.5 73.8 63.2 5.7
15 880 16.3 89.5 92.8 G 89.5 120.6 220.4 90.2 89.5 91.1 91.3 76.5 71.7 61.2 5.9
20 3550 18.1 109.9 116.0 G 29.6 59.5 62.0 92.4 91.7 93.5 93.5 89.5 89.5 87.2 2.5
20 1770 18.6 111.3 116.0 G 59.4 131.2 142.9 93.0 92.4 93.7 93.9 86.5 84.0 77.0 4.8
20 1180 20.7 111.6 116.0 G 88.9 130.6 209.5 91.7 91.0 92.7 92.7 79.0 74.5 64.1 7.4
20 875 23.9 107.4 116.0 G 119.8 181.9 255.4 91.0 90.2 91.4 90.8 69.0 60.7 49.0 11.4
25 3550 22.2 137.2 146.0 G 36.9 87.6 88.8 93.0 92.4 93.4 93.1 90.5 89.6 85.5 3.8
25 1775 23.7 132.7 146.0 G 73.9 135.2 166.4 93.6 93.0 94.2 94.0 84.5 81.4 73.0 7.0
25 1180 25.8 138.5 146.0 G 111.4 209.7 260.2 93.0 92.4 93.3 92.8 78.0 71.3 60.6 10.0
25 880 30.7 148.6 146.0 G 149.5 263.9 355.9 91.0 90.2 91.4 90.4 67.0 58.1 46.2 15.7
30 3550 26.7 166.0 174.0 G 44.4 109.6 107.3 93.0 92.4 93.7 93.5 90.5 89.8 85.7 4.5
30 1775 28.2 153.6 174.0 G 88.7 159.2 192.7 93.6 93.0 94.3 94.3 85.0 82.4 74.6 7.8
30 1175 30.6 159.0 174.0 G 133.8 245.6 298.8 93.0 92.4 93.5 93.2 79.0 72.9 62.8 11.1
30 890 33.8 150.7 174.0 G 177.2 242.9 383.6 92.4 91.7 93.8 93.2 72.0 64.1 52.4 15.1
40 3575 37.4 221.3 232.0 G 58.8 94.1 148.8 94.1 93.6 94.0 92.9 85.0 77.4 68.1 11.9
40 1785 40.6 224.2 232.0 G 117.8 205.8 273.7 94.5 94.1 94.5 93.9 78.0 71.0 59.9 16.5
40 1185 39.8 217.7 232.0 G 176.9 275.5 443.0 94.1 93.6 94.6 94.2 80.0 73.8 63.1 14.9
40 890 45.0 210.4 232.0 G 236.3 349.0 535.5 93.0 92.4 94.0 93.3 71.5 62.9 51.0 21.1

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA®
TEFC- Extra Severe Duty
Typical Performance Data cont.
Volts: 575
HP: 0.75 - 300
NP Eff Guar. 75% 50% NP PF 75% Load 50% Load
NP Design NEMA B Code FLT LRT BDT Full Eff. Full Load Load Full Power Power Max
HP FL RPM FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff Eff Load Factor Factor KVAR
50 3570 45.5 266.7 290 G 73.5 123.2 178.6 94.5 94.1 94.6 93.9 87.0 80.7 72.7 12.6
50 1780 51.1 274.0 290 G 147.4 257.5 333.7 94.5 94.1 94.6 94.1 77.5 70.5 59.4 20.8
50 1185 49.7 270.4 290 G 221.2 349.4 550.4 94.1 93.6 94.6 94.4 80.0 73.4 62.6 18.9
50 885 53.0 267.3 290 G 297.4 446.0 753.8 93.0 92.4 94.2 93.8 76.0 68.5 56.8 22.4
60 3570 56.3 301.0 348 G 88.3 116.7 206.9 95.0 94.5 94.7 93.9 84.0 76.3 66.9 18.4
60 1780 56.6 318.7 348 G 177.2 353.6 434.2 95.0 94.5 95.1 94.8 83.5 78.1 68.6 19.0
60 1190 58.0 321.5 348 G 264.3 383.6 607.2 95.0 94.5 95.1 94.6 81.5 76.2 66.4 20.1
60 880 63.1 319.5 348 G 357.0 544.9 903.3 93.0 92.4 94.4 94.2 76.5 69.3 57.9 25.9
75 3570 72.3 411.8 434 G 110.3 172.1 277.6 93.6 93.0 94.9 94.0 83.0 74.1 63.7 25.4
75 1785 69.7 412.2 434 G 220.8 346.2 554.9 95.4 95.0 95.7 95.4 84.5 79.9 71.0 21.9
75 1190 71.2 382.2 434 G 330.5 470.5 720.4 95.0 94.5 95.3 95.0 83.0 78.0 69.2 22.7
75 890 75.2 385.1 434 G 442.2 615.3 1017.8 94.5 94.1 95.2 94.7 79.0 73.1 63.0 27.5
100 3570 86.3 565.0 580 G 147.0 247.5 383.2 95.4 95.0 95.8 95.6 91.0 87.4 82.5 17.0
100 1785 95.3 478.7 580 G 293.9 433.7 678.3 95.8 95.4 96.0 95.7 82.0 76.2 66.2 33.7
100 1195 93.4 559.2 580 G 440.1 603.5 1093.9 95.4 95.0 95.5 94.8 84.0 79.2 70.3 29.7
100 890 100.0 500.7 580 G 590.2 822.4 1330.7 94.5 94.1 95.3 94.9 79.0 73.6 63.7 35.8
125 3580 112.0 663.9 726 G 183.3 226.6 485.6 95.4 95.0 95.8 95.2 87.5 81.4 73.3 31.0
125 1780 115.0 598.3 726 G 368.2 649.0 894.1 95.8 95.4 95.8 95.3 85.0 80.2 71.6 35.7 3.13
125 1190 120.0 670.6 726 G 550.7 961.9 1276.9 95.4 95.0 95.5 95.0 82.0 76.6 67.1 40.8

X$D ULTRA® - Performance Data

125 890 124.0 663.5 726 G 737.7 1125.4 1812.6 95.0 94.5 95.4 95.1 79.5 73.5 63.5 45.0
150 3580 132.0 800.1 868 G 220.0 298.3 578.2 95.8 95.4 96.1 95.7 89.0 83.5 76.4 33.2
150 1790 137.0 831.2 868 G 439.7 515.7 1162.5 96.2 95.8 96.5 96.0 85.5 80.6 71.8 42.7
150 1190 137.0 815.4 868 G 660.4 989.7 1739 95.8 95.4 95.9 95.6 85.5 81.3 73.3 39.7
150 890 147.0 776.2 868 G 885.2 1328.1 2089.9 95.0 94.5 95.8 95.6 80.5 75.4 66.1 49.1
200 3580 170.0 1050.3 1160 G 293.4 442.6 808.1 95.8 95.4 95.9 95.4 92.0 88.7 84.8 30.2
200 1790 177.0 988.6 1160 G 586.5 652.9 1418.7 96.5 96.2 96.6 96.4 87.5 83.9 77.0 46.4
200 1190 183.0 1054.4 1160 G 881.1 1316.3 2249.4 95.8 95.4 96.0 95.8 85.5 81.9 74.4 50.6
250 3575 211.0 1264.0 1460 G 366.9 578.1 960.0 95.8 95.4 96.2 95.9 92.5 89.9 86.9 32.6
250 1790 218.0 1226.8 1460 G 733.0 868.8 1730.5 96.5 96.2 96.8 96.8 89.0 86.4 81.0 48.8
300 3580 255.0 1623.9 1760 G 440.2 708.1 1217.0 95.8 95.4 96.4 96.1 92.0 89.4 85.7 42.9
300 1790 265.0 1594.5 1760 G 879.2 1128.2 2239.5 96.5 96.2 96.3 95.9 88.0 84.7 78.0 67.6

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA®
TEFC- Extra Severe Duty
Dimensions

Dimensions refer to drawing on following page.

Cast Iron Construction/Frames 140-449, Type KS, 3-Phase/Dimensions – For Estimating Only.
Dimensions in Inches
Approx. Shaft Mounting (18)
Net
Weight Key
Frame(19) in lbs Width Depth Length N-W U(1) V E H BA BS 2F 2XF A B C D(3) G J K L O
143T 43 0.187 0.187 1.380 2.25 0.875 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
145T 50 0.187 0.187 1.380 2.25 0.875 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
182T 76 0.250 0.250 1.750 2.75 1.125 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
184T 101 0.250 0.250 1.750 2.75 1.125 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
213T 200 0.312 0.312 2.380 3.38 1.375 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
215T 220 0.312 0.312 2.380 3.38 1.375 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
254T 315 0.375 0.375 2.380 4.00 1.625 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
256T 350 0.375 0.375 2.880 4.00 1.625 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
284TS 460 0.375 0.375 1.880 3.25 1.625 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
284T 460 0.500 0.500 3.250 4.62 1.875 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
286TS 510 3.750 3.750 1.880 3.25 1.625 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
286T 510 0.500 0.500 3.250 4.62 1.875 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
324TS 664 0.500 0.500 2.000 3.75 1.875 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 29.04 8.00 0.99 2.01 3.62 15.54 17.07
324T 664 0.500 0.500 3.880 5.25 2.125 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
326TS 800 0.500 0.500 2.000 3.75 1.875 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
3.14 326T 800 0.500 0.500 3.880 5.25 2.125 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 32.04 8.00 0.99 2.01 3.62 15.54 17.07
364TS 1122 0.500 0.500 2.000 3.75 1.875 3.50 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 32.76 9.00 1.09 2.26 3.40 17.00 19.02
364T 1122 0.625 0.625 4.250 5.88 2.375 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02
365TS 1155 0.500 0.500 2.000 3.75 1.875 3.50 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 32.76 9.00 1.09 2.26 3.40 17.00 19.02
365T 1155 0.625 0.625 4.250 5.88 2.375 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02
X$D ULTRA®

404TS 1580 0.500 0.500 2.750 4.25 2.125 4.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 36.76 10.00 1.29 2.64 4.00 19.02 21.18
404T 1580 0.750 0.750 5.625 7.25 2.875 7.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 39.77 10.00 1.29 2.64 4.00 19.02 21.18
405TS 1600 0.500 0.500 2.750 4.25 2.125 4.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 36.76 10.00 1.29 2.64 4.00 19.02 21.18
405T 1600 0.750 0.750 5.625 7.25 2.875 7.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 39.77 10.00 1.29 2.64 4.00 19.02 21.18
444TS 2100 0.625 0.625 3.000 4.75 2.375 4.50 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 41.87 11.00 1.49 2.64 4.97 21.37 23.94
444T 2100 0.875 0.875 6.875 8.50 3.375 8.25 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 45.62 11.00 1.49 2.64 4.97 21.37 23.94
445TS 2260 0.625 0.625 3.000 4.75 2.375 4.50 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 41.87 11.00 1.49 2.64 4.97 21.37 23.94
445T 2260 0.875 0.875 6.875 8.50 3.375 8.25 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 45.62 11.00 1.49 2.64 4.97 21.37 23.94
447TS 2610 0.625 0.625 3.000 4.75 2.375 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.37 11.00 1.49 2.64 8.81 25.62 23.94
447T 2610 0.875 0.875 6.875 8.50 3.375 8.25 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 54.12 11.00 1.49 2.64 8.81 25.62 23.94
449TS 3010 0.625 0.625 3.000 4.75 2.375 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.37 11.00 1.49 2.64 8.81 25.62 23.94
449T 3010 0.875 0.875 6.875 8.50 3.375 8.25 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 54.12 11.00 1.49 2.64 8.81 25.62 23.94
1. Shaft diameters 1 1/2 inches and smaller will come within the limits of +0.000 inch, -0.0005 inch diameters 1 5/8 inches and larger +0.000 inch, -0.001 inch
3. Tolerance on “D” dimension for rigid base motors will be +0.000 inch, -0.060 inch. No tolerance has been est. for the “D” dimension of resilient mounted motors.
18. Motor feet have 2 holes per foot allowing NEMA F-1 or F-2 assembly while maintaining critical NEMA mounting dimensions.
19. Cast iron motors in 449 frame also have mounting holes meeting 447 frame dimensions.
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward, or from either side.
Weights shown are approximate shipping weights and should be used for estimating only.

www.gemotors.com Data subject to change without notice. GEP-500S

GEP-500T 03/08.
02/08.
 X$D ULTRA®
TEFC- Extra Severe Duty
Dimensions
Dimensions on previous page.

Cast Iron Construction/Frames 140-449, Type KS, 3-Phase/Dimensions – For Estimating Only.

3.15
Conduit Box Dimensions
Approx. Dimensions in Inches
Nominal Vol.
Frame HP (cubic in) AA* AB AC AF XL XN
143-145 2 32 0.75 6.62 5.12 2.50 4.30 5.40

X$D ULTRA®
182-184 5 32 0.75 7.82 6.32 2.50 4.30 5.40
213-215 10 55 1.00 9.50 7.42 3.50 5.78 4.16
254-256 20 140 1.25 11.68 9.12 4.59 7.37 5.37
284-286 30 140 1.50 12.44 9.88 4.59 7.37 5.37
324-326 50 346 3.00 16.13 12.43 6.44 10.14 7.00
364-365 75 346 3.00 17.07 13.37 6.44 10.14 7.00
404-405 125 700 3.00 20.48 16.22 7.00 12.13 10.50
444-449 200 700 3.00 22.00 17.74 7.00 12.13 10.50
444-449 250-300 1260 4.00 TBD TBD 7.00 12.40 16.25
* A tapped NPT hole is provided for the conduit size listed in Column AA

C-Face Dimensions
All Dimensions in inches
Key Key Key
NEMA Frame AH AJ AK U Width Thickness Length
143TC-145TC 2.12 5.88 4.50 0.875 0.19 0.19 1.38
182TC-184TC 2.62 7.25 8.50 1.125 0.25 0.25 1.75
213TC-215TC 3.12 7.25 8.50 1.375 0.31 0.31 2.38
254TC-256TC 3.75 7.25 8.50 1.625 0.38 0.38 2.88
284TC-286TC 4.38 9.00 10.50 1.875 0.50 0.50 3.25

Data subject to change without notice. GEP-500S

GEP-500T 03/08.
02/08. www.gemotors.com
3.16

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
GEGARD2400 TM
TEFC- Extra Severe Duty
INVERTER
DUTY
EXCEEDS
NEMA
MG1-31
Standard Features

HP Range 0.75-250
Poles 2,4,6,8
Voltage 460, 575
Efficiency Meets or exceeds NEMA Premium nominal. Exceeds all NEMA Premium minimum efficiencies.
Frequency 60 Hz
NEMA Design B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration ISO Grade 1, Ball Bearings: 0.040 in/sec (P)
Roller Bearing:2P: 0.0003 in (P-P), 4P: 0.0004 in (P-P), 6P: 0.0005 in (P-P), 8P: 0.0007 in (P-P)
Bearing Caps 143-449: Both ends are gasketed
Bearing Housing Rise 2-pole: 50ºC, 4,6,8-pole: 45ºC
Bearing Protection IP55, Inpro Seal both ends
Bearing Type Ball, Belted 4-pole 250-300 HP have Roller Brg
Centered Core Allows F1-F2 field conversion
Conduit Box Gasketed and rotatable, Cast iron
Div 2 Temp Codes NEMA Design B motors have an Auto Ignition Temperature of 200 degree C stamped on the
nameplate. A Division 2 Nameplate can be provided (see kit section).
Drains Stainless Steel T-drains in lowest section of both endshields
End Shield Cast Iron
Fan Non-Sparking Plastic or Bronze
Fan Cover Cast Iron
3.17
Fasteners SAE, Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 inches
Frame Material Cast Iron

X$D ULTRA® 841

Frame Size 143-449
Grease Polyurea
Ground Ground lug in Conduit Box and Frame ground
Industry Specifications Meets IEEE 45 Marine Duty
Meets GM 7E-TA Automotive Duty
Insulation Class Class H for 320 frame & larger, all others Class F with H materials
Insulation System GEGARD2400TM 320-449 frames. GEGARD2000TM 140-280 frames. Non-Hygroscopic,
Anti-Fungus, 2400Volt or 2000Volt @ .1microsecond rise time. Exceeds NEMA MG1-31
Inverter Capabilities Variable Torque inf:1, Constant Torque 20:1 (see Inverter Duty Capabilities, page vii)
L10 Bearing Life Direct Coupled: 130,000 hrs, Belted: 26,280 hrs
Lifting Means 4 Lugs cast into frame
Mounting F1 as Standard and Modifiable to F2
Mounting Holes 1 per foot (324 frame), 2 per foot (all other frames)
Nameplate Stainless Steel Includes weight, 3/4 load efficiency, vibration limit
Oil Mist Lube Includes provisions for conversion to Oil Mist Lubrication
Paint Buff, Epoxyester
Relubrication Both ends, extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15
Shaft TIR Meets IEEE 841, .001 in for shaft diameter 1.625 in and smaller, .0015 in for shaft
diameter greater than 1.625 in.
Special Painting Meets IEEE 841
Tach Mounting Tach kits for field modifications are available
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine Report including Vibration supplied with motor, IEEE 112
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 60 months from date of purchase or 66 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY
EXCEEDS

Pricing NEMA
MG1-31

Volts: 460, 575

HP: 0.75 - 250
Nom Guar. Cat List Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Price Symbol Norm Stk (lbs) (in) Notes
0.75 1200 460 143T 1.4 80.0 78.5 M354 $672 G4-7UX1 N 43 13.40
0.75 1200 575 143T 1.1 80.0 78.5 M355 $672 G4-7UX1 N 43 13.40
0.75 900 460 145T 1.9 72.0 70.0 M8901 $1,108 G4-7UX1 N 50 13.40
1 3600 460 143T 1.3 87.5 86.5 M8903 $690 G4-7UX1 N 43 11.60 55
1 3600 575 143T 1.1 87.5 86.5 M8904 $690 G4-7UX1 N 43 11.60 55
1 1800 460 143T 1.4 86.5 85.5 M352 $680 G4-7UX1 Y 43 11.60
1 1800 575 143T 1.2 86.5 85.5 M353 $680 G4-7UX1 N 43 11.60
1 1200 460 145T 1.8 82.5 81.5 M363 $728 G4-7UX1 N 50 13.40
1 1200 575 145T 1.5 82.5 81.5 M364 $728 G4-7UX1 N 50 13.40
1 900 460 182T 2.2 80.0 78.5 M9413 $889 G4-7UX1 N 76 15.90 55
1 900 575 182T 1.8 80.0 78.5 M9482 $889 G4-7UX1 N 76 15.90 55
1.5 3600 460 143T 2.0 87.5 86.5 M8905 $720 G4-7UX1 N 43 11.60 55
1.5 3600 575 143T 1.6 87.5 86.5 M8906 $720 G4-7UX1 N 43 11.60 55
1.5 1800 460 145T 2.1 86.5 85.5 M359 $771 G4-7UX1 Y 50 11.60
1.5 1800 575 145T 1.7 86.5 85.5 M360 $771 G4-7UX1 N 50 11.60
1.5 1200 460 182T 2.4 87.5 86.5 M9414 $697 G4-7UX1 N 76 15.90
1.5 1200 575 182T 1.9 87.5 86.5 M9483 $697 G4-7UX1 N 76 15.90
1.5 900 460 184T 3.2 80.0 78.5 M9415 $1,051 G4-7UX1 N 101 15.90
3.18 1.5 900 575 184T 2.6 80.0 78.5 M9485 $1,051 G4-7UX1 N 101 15.90
2 3600 460 143T 2.7 86.5 85.5 M8907 $862 G4-7UX1 N 43 11.60 55
2 3600 575 143T 2.2 86.5 85.5 M8908 $862 G4-7UX1 N 43 11.60 55
2 1800 460 145T 2.7 86.5 85.5 M361 $833 G4-7UX1 Y 50 13.40
X$D ULTRA® 841

2 1800 575 145T 2.2 86.5 85.5 M362 $833 G4-7UX1 N 50 13.40
2 1200 460 184T 3.0 88.5 87.5 M9416 $779 G4-7UX1 N 101 15.90
2 1200 575 184T 2.5 88.5 87.5 M9486 $779 G4-7UX1 N 101 15.90
2 900 460 213T 3.8 86.5 85.5 M9417 $1,354 G4-7UX1 N 200 20.10
2 900 575 213T 3.0 86.5 85.5 M9487 1,354 G4-7UX1 N 200 20.10
3 3600 460 182T 3.9 89.5 88.5 M9418 $718 G4-7UX1 Y 76 15.90 55
3 3600 575 182T 3.1 89.5 88.5 M9488 $718 G4-7UX1 N 76 15.90 55
3 1800 460 182T 4.2 89.5 88.5 M9419 $674 G4-7UX1 Y 76 15.90 55
3 1800 575 182T 3.3 89.5 88.5 M9489 $674 G4-7UX1 N 76 15.90 55
3 1200 460 213T 4.2 89.5 88.5 M9420 $950 G4-7UX1 Y 200 20.10
3 1200 575 213T 3.4 89.5 88.5 M9490 $950 G4-7UX1 N 200 20.10
3 900 460 215T 5.4 86.5 85.5 M9421 $1,747 G4-7UX1 N 220 20.10
3 900 575 215T 4.3 86.5 85.5 M9491 $1,747 G4-7UX1 N 220 20.10
Notes
55 TENV Construction

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
GEGARD2400 TM
INVERTER
TEFC- Extra Severe Duty
DUTY
EXCEEDS
NEMA
MG1-31
Pricing cont.

Volts: 460, 575

HP: 0.75 - 250
Nom Guar. Cat List Price Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) (in) Notes
5 3600 460 184T 6.3 90.2 89.5 M9422 $889 G4-7UX1 Y 101 15.90
5 3600 575 184T 5.0 90.2 89.5 M9492 $889 G4-7UX1 N 101 15.90
5 1800 460 184T 6.6 89.5 88.5 M9423 $788 G4-7UX1 N 101 15.90
5 1800 575 184T 5.3 89.5 88.5 M9493 $788 G4-7UX1 N 101 15.90
5 1200 460 215T 7.2 89.5 88.5 M9424 $1,338 G4-7UX1 Y 220 20.10
5 1200 575 215T 5.4 89.5 88.5 M9494 $1,338 G4-7UX1 N 220 20.10
5 900 460 254T 8.1 89.5 88.5 M9425 $2,410 G4-7UX1 N 315 25.60
5 900 575 254T 6.5 89.5 88.5 M9495 $2,410 G4-7UX1 N 315 25.60
7.5 3600 460 213T 8.5 91.0 90.2 M9426 $1,074 G4-7UX1 Y 200 20.10
7.5 3600 575 213T 6.8 91.0 90.2 M9496 $1,074 G4-7UX1 N 200 20.10
7.5 1800 460 213T 9.1 91.7 91.0 M9427 $1,067 G4-7UX1 Y 200 20.10
7.5 1800 575 213T 7.2 91.7 91.0 M9497 $1,067 G4-7UX1 N 200 20.10
7.5 1200 460 254T 9.8 91.7 91.0 M9428 $1,778 G4-7UX1 Y 315 25.60
7.5 1200 575 254T 7.9 91.7 91.0 M9498 $1,778 G4-7UX1 N 315 25.60
7.5 900 460 256T 11.6 89.5 88.5 M9429 $3,051 G4-7UX1 N 350 25.60
7.5 900 575 256T 9.3 89.5 88.5 M9499 $3,051 G4-7UX1 N 350 25.60
10 3600 460 215T 11.2 91.0 90.2 M9430 $1,255 G4-7UX1 Y 220 20.10
10 3600 575 215T 9.0 91.0 90.2 M9563 $1,255 G4-7UX1 N 220 20.10
10 1800 460 215T 12.0 91.7 91.0 M9431 $1,286 G4-7UX1 Y 220 20.10 3.19
10 1800 575 215T 9.6 91.7 91.0 M9564 $1,286 G4-7UX1 N 220 20.10
10 1200 460 256T 13.1 91.0 90.2 M9432 $2,173 G4-7UX1 Y 350 25.60
10 1200 575 256T 10.5 91.0 90.2 M9565 $2,173 G4-7UX1 N 350 25.60

X$D ULTRA® 841

10 900 460 284T 13.8 90.2 89.5 M9433 $3,617 G4-7UX1 N 460 28.58
10 900 575 284T 11.0 90.2 89.5 M9566 $3,617 G4-7UX1 N 460 28.58
15 3600 460 254T 17.6 91.7 91.0 M9434 $1,725 G4-7UX1 Y 315 25.60
15 3600 575 254T 14.0 91.7 91.0 M9567 $1,725 G4-7UX1 N 315 25.60
15 1800 460 254T 18.0 92.4 91.7 M9435 $1,694 G4-7UX1 Y 315 25.60
15 1800 575 254T 14.4 92.4 91.7 M9568 $1,694 G4-7UX1 N 315 25.60
15 1200 460 284T 19.6 91.7 91.0 M9436 $2,882 G4-7UX1 Y 460 28.58
15 1200 575 284T 15.7 91.7 91.0 M9569 $2,882 G4-7UX1 N 460 28.58
15 900 460 286T 20.5 90.2 89.5 M9437 $4,726 G4-7UX1 N 510 28.58
15 900 575 286T 16.4 90.2 89.5 M9570 $4,726 G4-7UX1 N 510 28.58
20 3600 460 256T 22.6 92.4 91.7 M9438 $2,135 G4-7UX1 Y 350 25.60
20 3600 575 256T 18.1 92.4 91.7 M9571 $2,135 G4-7UX1 N 350 25.60
20 1800 460 256T 23.3 93.0 92.4 M9439 $2,111 G4-7UX1 Y 350 25.60
20 1800 575 256T 18.6 93.0 92.4 M9572 $2,111 G4-7UX1 N 350 25.60
20 1200 460 286T 26.0 91.7 91.0 M9440 $3,512 G4-7UX1 Y 510 28.58
20 1200 575 286T 20.8 91.7 91.0 M9573 $3,512 G4-7UX1 N 510 28.58
20 900 460 324T 29.8 91.0 90.2 M9441 $5,459 G4-7UX1 N 649 30.54
20 900 575 324T 23.9 91.0 90.2 M9574 $5,459 G4-7UX1 N 649 30.54

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY
EXCEEDS

Pricing cont.
NEMA
MG1-31

Volts: 460, 575

HP: 0.75 - 250
Nom Guar. Cat List Price Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) (in) Notes
25 3600 460 284TS 27.8 93.0 92.4 M9442 $2,632 G4-7UX1 Y 460 27.20
25 3600 575 284TS 22.2 93.0 92.4 M9575 $2,632 G4-7UX1 N 460 27.20
25 1800 460 284T 29.8 93.6 93.0 M9443 $2,514 G4-7UX1 Y 460 28.58
25 1800 575 284T 23.8 93.6 93.0 M9576 $2,514 G4-7UX1 N 460 28.58
25 1200 460 324T 32.3 93.0 92.4 M9444 $4,446 G4-7UX1 N 679 30.54
25 1200 575 324T 25.8 93.0 92.4 M9577 $4,446 G4-7UX1 N 679 30.54
25 900 460 326T 37.0 91.0 90.2 M9445 $6,538 G4-7UX1 N 710 32.04
25 900 575 326T 29.2 91.0 90.2 M9578 $6,538 G4-7UX1 N 710 32.04
30 3600 460 286TS 33.4 93.0 92.4 M9446 $3,073 G4-7UX1 Y 510 27.20
30 3600 575 286TS 26.7 93.0 92.4 M9579 $3,073 G4-7UX1 N 510 27.20
30 1800 460 286T 35.5 93.6 93.0 M9447 $2,922 G4-7UX1 Y 510 28.58
30 1800 575 286T 28.4 93.6 93.0 M9580 $2,922 G4-7UX1 N 510 28.58
30 1200 460 326T 38.2 93.0 92.4 M9448 $4,962 G4-7UX1 Y 730 32.04
30 1200 575 326T 30.8 93.0 92.4 M9581 $4,962 G4-7UX1 N 730 32.04
30 900 460 364T 42.2 92.4 91.7 M9449 $8,073 G4-7UX N 1010 34.89
30 900 575 364T 33.8 92.4 91.7 M9582 $8,073 G4-7UX N 1010 34.89
40 3600 460 324TS 46.8 94.1 93.6 M9450 $4,176 G4-7UX1 Y 649 29.04
40 3600 575 324TS 37.4 94.1 93.6 M9583 $4,176 G4-7UX1 N 649 29.04
3.20 40 1800 460 324T 50.8 94.5 94.1 M9451 $4,051 G4-7UX1 Y 689 30.54
40 1800 575 324T 40.6 94.5 94.1 M9584 $4,051 G4-7UX1 N 689 30.54
40 1200 460 364T 49.4 94.1 93.6 M9452 $6,633 G4-7UX Y 1030 34.89
40 1200 575 364T 39.8 94.1 93.6 M9585 $6,633 G4-7UX N 1030 34.89
X$D ULTRA® 841

40 900 460 365T 55.9 93.0 92.4 M9453 $9,958 G4-7UX N 1090 34.89
40 900 575 365T 45.0 93.0 92.4 M9586 $9,958 G4-7UX N 1090 34.89
50 3600 460 326TS 57.3 94.5 94.1 M9454 $5,098 G4-7UX1 Y 700 30.48
50 3600 575 326TS 45.5 94.5 94.1 M9587 $5,098 G4-7UX1 N 700 30.48
50 1800 460 326T 63.9 94.5 94.1 M9455 $4,615 G4-7UX1 Y 740 32.04
50 1800 575 326T 51.1 94.5 94.1 M9588 $4,615 G4-7UX1 N 740 32.04
50 1200 460 365T 62.2 94.1 93.6 M9456 $7,562 G4-7UX Y 1070 34.89
50 1200 575 365T 49.7 94.1 93.6 M9589 $7,562 G4-7UX N 1070 34.89
50 900 460 404T 66.6 93.0 92.4 M9457 $12,015 G4-7UX N 1490 39.77
50 900 575 404T 53.0 93.0 92.4 M9590 $12,015 G4-7UX N 1490 39.77
60 3600 460 364TS 70.4 95.0 94.5 M9458 $6,837 G4-7UX Y 940 32.76
60 3600 575 364TS 56.3 95.0 94.5 M9591 $6,837 G4-7UX N 940 32.76
60 1800 460 364T 71.2 95.0 94.5 M9459 $6,616 G4-7UX Y 1020 34.89
60 1800 575 364T 56.6 95.0 94.5 M9592 $6,616 G4-7UX N 1020 34.89
60 1200 460 404T 72.5 95.0 94.5 M9460 $8,830 G4-7UX N 1480 39.77
60 1200 575 404T 58.0 95.0 94.5 M9593 $8,830 G4-7UX N 1480 39.77
60 900 460 405T 78.9 93.0 92.4 M9461 $13,560 G4-7UX N 1570 39.77
60 900 575 405T 63.1 93.0 92.4 M9594 $13,560 G4-7UX N 1570 39.77
75 3600 460 365TS 85.2 95.8 95.4 M9462 $8,174 G4-7UX Y 1020 32.76
75 3600 575 365TS 68.6 95.8 95.4 M8917 $8,174 G4-7UX N 1020 32.76
75 1800 460 365T 86.6 95.4 95.0 M9463 $7,839 G4-7UX Y 1090 34.89
75 1800 575 365T 68.9 95.4 95.0 M9596 $7,839 G4-7UX N 1090 34.89
75 1200 460 405T 89.6 95.0 94.5 M9464 $9,698 G4-7UX Y 1540 39.77
75 1200 575 405T 71.2 95.0 94.5 M9597 $9,698 G4-7UX N 1540 39.77
75 900 460 444T 94.0 94.5 94.1 M9465 $16,966 G4-7UX N 1950 45.62
75 900 575 444T 75.2 94.5 94.1 M9598 $16,966 G4-7UX N 1950 45.62

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
GEGARD2400 TM
INVERTER
TEFC- Extra Severe Duty
DUTY
EXCEEDS

Pricing cont.
NEMA
MG1-31

Volts: 460, 575

HP: 0.75 - 250
Nom Guar. Cat List Price Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) (in) Notes
100 3600 460 405TS 108.0 95.4 95.0 M9466 $10,522 G4-7UX N 1530 36.76 66
100 3600 460 405TS 108.0 95.4 95.0 M8975 $10,522 G4-7UX N 1530 36.76 62
100 3600 575 405TS 86.3 95.4 95.0 M8918 $10,522 G4-7UX N 1530 36.76 66
100 1800 460 405T 119.0 95.8 95.4 M9467 $9,651 G4-7UX Y 1480 39.77
100 1800 575 405T 95.3 95.8 95.4 M9693 $9,651 G4-7UX N 1480 39.77 113
100 1200 460 444T 116.0 95.4 95.0 M9468 $12,482 G4-7UX Y 2060 45.62
100 900 460 445T 125.0 94.5 94.1 M9469 $21,498 G4-7UX N 2020 45.62
100 900 575 445T 100.0 94.5 94.1 M9695 $21,498 G4-7UX N 2020 45.62
125 3600 460 444TS 139.0 95.4 95.0 M9470 $13,446 G4-7UX N 1790 41.87 66
125 3600 460 444TS 136.0 95.4 95.0 M8976 $13,446 G4-7UX N 1880 41.87 62
125 3600 575 444TS 112.0 95.4 95.0 M8919 $13,446 G4-7UX N 1790 41.87 66
125 1800 460 444T 144.0 95.8 95.4 M9471 $12,434 G4-7UX Y 1970 45.62
125 1800 575 444T 115.0 95.8 95.4 M9697 $12,434 G4-7UX N 1970 45.62
125 1200 460 445T 150.0 95.4 95.0 M9472 $14,871 G4-7UX N 2130 45.62
125 1200 575 445T 120.0 95.4 95.0 M9698 $14,871 G4-7UX N 2130 45.62
125 900 460 447T 155.0 95.0 94.5 M9473 $23,939 G4-7UX N 2580 52.12
125 900 575 447T 124.0 95.0 94.5 M9699 $23,939 G4-7UX N 2580 52.12
150 3600 460 445TS 163.0 95.8 95.4 M9474 $15,916 G4-7UX N 1930 41.87 66
150 3600 460 445TS 162.0 95.8 95.4 M8977 $15,916 G4-7UX N 2000 41.87 62
3.21
150 3600 575 445TS 130.0 95.8 95.4 M8920 $15,916 G4-7UX N 1930 41.87 66
150 1800 460 445T 170.0 96.2 95.8 M9475 $14,287 G4-7UX Y 2090 45.62
150 1800 575 445T 137.0 96.2 95.8 M9384 $14,287 G4-7UX N 2060 45.62

X$D ULTRA® 841

150 1200 460 447T 171.0 95.8 95.4 M9476 $18,108 G4-7UX N 2860 52.12
150 1200 575 447T 137.0 95.8 95.4 M9385 $18,108 G4-7UX N 2860 52.12
150 900 460 449T 184.0 95.0 94.5 M8937 $26,105 G4-7UX N 3150 52.12
150 900 575 449T 147.0 95.0 94.5 M8938 $26,105 G4-7UX N 3120 52.12
200 3600 460 447TS 214.0 95.8 95.4 M9477 $19,819 G4-7UX N 2560 50.37 66, 112
200 3600 460 447TS 214.0 95.8 95.4 M8978 $19,819 G4-7UX N 2630 50.37 62, 112
200 3600 575 447TS 170.0 95.8 95.4 M8939 $19,819 G4-7UX N 2560 50.37 66, 112
200 1800 460 447T 220.0 96.5 96.2 M9478 $17,614 G4-7UX Y 2800 54.12
200 1800 575 447T 175.0 96.5 96.2 M9387 $17,614 G4-7UX N 2800 54.12
200 1200 460 449T 229.0 95.8 95.4 M8940 $20,142 G4-7UX N 3070 54.12
200 1200 575 449T 183.0 95.8 95.4 M8941 $20,142 G4-7UX N 3070 54.12
200 900 460 449T 247.0 95.4 95.0 M8942 $27,500 G4-7UX N 3120 54.12 113
250 3600 460 449TS 265.0 95.8 95.4 M8943 $25,052 G4-7UX N 2770 50.37 66, 112, 113
250 3600 460 449TS 265.0 95.8 95.4 M8979 $25,052 G4-7UX N 2770 50.37 62, 112, 113
250 3600 575 449TS 211.0 95.8 95.4 M8944 $25,052 G4-7UX N 2770 50.37 66, 112, 113
250 1800 460 449T 280.0 96.2 95.8 M8945 $20,436 G4-7UX Y 2790 54.12 112
250 1800 575 449T 224.0 96.2 95.8 M8946 $20,436 G4-7UX N 2790 54.12 112
Notes
62 Connected for CCW rotation facing opposite shaft end. No reconnection possible
66 CW rotation only facing opposite drive end. CCW rotation available, but must be specified on the order
112 Noise level exceeds IEEE-841
113 Bearing temperature exceeds IEEE-841

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY

C-Face EXCEEDS
NEMA
MG1-31

Pricing

Volts: 460
HP: 1 - 50
Nom Guar. Cat List Price Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Symbol Norm Stk (lbs) (in) Notes
1 1800 460 143TC 1.4 86.5 85.5 M520 $763 G4-7UX1 N 43 13.92
1.5 1800 460 145TC 2.1 86.5 85.5 M521 $857 G4-7UX1 N 50 13.92
1.5 1200 460 182TC 2.4 87.5 86.5 M8926 $789 G4-7UX1 N 76 16.65
2 1800 460 145TC 2.7 86.5 85.5 M526 $918 G4-7UX1 N 50 13.92
2 1200 460 184TC 3.0 88.5 87.5 M8928 $871 G4-7UX1 N 101 16.65
3 3600 460 182TC 3.9 89.5 88.5 M8925 $814 G4-7UX1 N 76 16.65 55
3 1800 460 182TC 4.2 89.5 88.5 M8909 $766 G4-7UX1 Y 76 16.65 55
5 3600 460 184TC 6.3 90.2 89.5 M8927 $989 G4-7UX1 N 101 16.65
5 1800 460 184TC 6.6 89.5 88.5 M8910 $880 G4-7UX1 Y 101 16.65
5 1200 460 215TC 7.2 89.5 88.5 M8932 $1,430 G4-7UX1 N 220 20.90
7.5 3600 460 213TC 8.5 91.0 90.2 M8929 $1,166 G4-7UX1 N 200 20.90
7.5 1800 460 213TC 9.1 91.7 91.0 M8911 $1,159 G4-7UX1 N 200 20.90
7.5 1200 460 254TC 9.8 91.7 91.0 M8934 $1,898 G4-7UX1 N 315 26.09
10 3600 460 215TC 11.2 91.0 90.2 M8931 $1,347 G4-7UX1 N 220 20.90
10 1800 460 215TC 12.0 91.7 91.0 M8912 $1,386 G4-7UX1 Y 220 20.90
10 1200 460 256TC 13.1 91.0 90.2 M8936 $2,292 G4-7UX1 N 350 26.09
3.22 15 3600 460 254TC 17.6 91.7 91.0 M8933 $1,845 G4-7UX1 N 315 26.09
15 1800 460 254TC 18.0 92.4 91.7 M8913 $1,818 G4-7UX1 N 315 26.09
15 1200 460 284TC 19.6 91.7 91.0 M8921 $3,050 G4-7UX1 N 460 28.58
20 3600 460 256TC 22.6 92.4 91.7 M8935 $2,258 G4-7UX1 N 350 26.09
X$D ULTRA® 841

20 1800 460 256TC 23.3 93.0 92.4 M8914 $2,241 G4-7UX1 N 350 26.09
20 1200 460 286TC 26.0 91.7 91.0 M8922 $3,679 G4-7UX1 N 510 28.58
25 3600 460 284TC 27.8 93.0 92.4 M8923 $2,804 G4-7UX1 N 460 27.20
25 1800 460 284TC 29.8 93.6 93.0 M8915 $2,685 G4-7UX1 N 460 28.58
30 3600 460 286TC 33.4 93.0 92.4 M8924 $3,243 G4-7UX1 N 510 27.20
30 1800 460 286TC 35.5 93.6 93.0 M8916 $3,091 G4-7UX1 N 510 28.58
40 3600 460 324TSC 46.3 94.1 93.6 M8971 $4,389 G4-7UX1 N 649 29.04
40 1800 460 324TC 49.8 94.5 94.1 M8972 $4,264 G4-7UX1 N 689 30.54
50 3600 460 326TSC 56.9 94.5 94.1 M8973 $5,311 G4-7UX1 N 700 30.48
50 1800 460 326TC 62.3 94.5 94.1 M8974 $4,829 G4-7UX1 N 740 32.04
Notes
55 TENV Construction

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
GEGARD2400 TM
INVERTER
TEFC- Extra Severe Duty
DUTY
EXCEEDS
NEMA
MG1-31

Typical Performance Data

Volts: 460
HP: 0.75 - 250
75% 50%
NP Guar. 75% 50% NP PF Load Load
FL Design NEMA B Code FLT LRT BDT Eff. Full Eff. Full Load Load Full Power Power Max
HP RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff Eff Load Factor Factor KVAR
0.75 1150 1.4 7.5 12.5 P 3.4 9.7 12.3 80.0 78.5 81.4 78.7 63.5 54.4 41.9 0.6
0.75 850 1.9 7.2 12.5 P 4.6 11.6 14.9 72.0 70.0 72.2 67.4 52.5 43.7 33.4 1.0
1 3540 1.3 12.8 10.0 N 1.5 4.6 6.3 87.5 86.5 89.3 88.0 81.5 75.1 63.2 0.4
1 1750 1.4 11.7 15.0 N 3.0 12.0 14.4 86.5 85.5 87.1 85.1 76.0 68.0 55.0 0.5
1 1155 1.8 10.8 15.0 N 4.6 14.6 18.1 82.5 81.5 83.4 80.9 62.5 53.5 41.1 0.8
1 875 2.2 10.5 15.0 N 6.0 11.0 19.3 80.0 78.5 79.6 75.6 52.5 43.9 33.3 1.2
1.5 3530 2.0 18.9 20.0 M 2.2 7.2 9.5 87.5 86.5 89.6 88.7 81.0 74.2 61.8 0.6
1.5 1740 2.1 16.6 20.0 M 4.5 17.4 20.4 86.5 85.5 87.6 86.3 77.5 69.9 56.9 0.8
1.5 1175 2.4 17.1 20.0 M 6.7 14.3 29.0 87.5 86.5 88.3 86.5 68.0 59.6 46.8 1.0
1.5 870 3.2 14.8 20.0 M 9.0 16.7 26.7 80.0 78.5 80.5 77.1 55.5 46.7 35.6 1.6
2 3515 2.7 23.9 25.0 L 3.0 9.2 12.0 86.5 85.5 89.2 88.6 80.5 73.2 60.4 0.8
2 1730 2.7 20.5 25.0 L 6.1 22.0 25.4 86.5 85.5 88.0 87.3 80.0 72.9 60.2 0.9
2 1170 3.0 22.2 25.0 L 9.0 19.2 37.8 88.5 87.5 88.8 87.4 69.5 61.4 48.6 1.2
2 880 3.8 20.5 25.0 L 11.9 21.6 38.2 86.5 85.5 85.8 83.2 57.0 48.9 37.4 1.9
3 3530 3.8 26.3 32.0 K 4.5 9.4 14.3 89.5 88.5 91.4 90.8 82.0 76.5 65.2 1.0
3.23
3 1760 4.2 29.3 32.0 K 8.9 22.7 30.1 89.5 88.5 89.8 88.8 75.5 68.7 56.2 1.5
3 1180 4.2 30.6 32.0 K 13.4 32.3 44.4 89.5 88.5 89.8 88.6 74.0 67.0 54.5 1.6
3 875 5.3 27.8 32.0 K 18.0 31.3 50.8 86.5 85.5 86.4 84.8 61.0 53.1 41.3 2.5
5 3540 6.2 45.7 46.0 J 7.4 17.9 25.2 90.2 89.5 91.3 90.3 84.0 79.3 69.2 1.5

X$D ULTRA® 841

5 1755 6.6 43.1 46.0 J 15.0 34.4 43.8 89.5 88.5 90.5 90.1 79.5 74.2 63.4 2.0
5 1175 7.1 45.9 46.0 J 22.4 48.3 61.2 89.5 88.5 90.2 89.7 74.0 68.2 56.5 2.5
5 880 8.0 44.1 46.0 J 29.8 54.6 89.2 89.5 88.5 89.6 88.1 65.0 56.8 44.3 3.5
7.5 3535 8.5 61.7 63.5 H 11.1 23.7 31.5 91.0 90.2 91.4 90.7 90.5 88.6 82.8 1.6
7.5 1770 9.1 61.2 63.5 H 22.3 41.5 61.3 91.7 91.0 92.1 91.7 84.5 81.6 73.4 2.2
7.5 1175 9.8 61.2 63.5 H 33.5 67.1 91.5 91.7 91.0 92.3 91.7 78.5 72.9 62.1 2.9
7.5 880 11.5 60.1 63.5 H 44.8 77.8 121.7 89.5 88.5 90.1 89.2 68.0 60.5 47.9 4.6
10 3525 11.2 76.3 81.0 H 14.9 31.2 38.5 91.0 90.2 91.9 91.8 92.0 90.6 86.5 1.8
10 1765 12.0 78.3 81.0 H 29.7 54.3 78.5 91.7 91.0 92.3 92.2 85.0 82.1 74.3 2.9
10 1170 13.0 78.4 81.0 H 44.8 87.9 118.6 91.0 90.2 92.0 91.8 79.0 73.6 62.8 3.9
10 880 13.7 78.5 81.0 H 59.5 89.6 142.3 90.2 89.5 91.0 91.0 75.5 70.2 59.3 4.2
15 3550 17.5 111.7 116.0 G 22.2 44.1 53.6 91.7 91.0 92.3 92.0 87.5 86.1 81.0 2.8
15 1770 18.0 109.5 116.0 G 44.5 97.3 114.0 92.4 91.7 93.0 92.9 84.5 81.1 72.4 4.3
15 1185 19.5 107.8 116.0 G 66.6 95.9 162.7 91.7 91.0 92.9 92.5 78.5 73.4 62.6 5.8
15 880 20.3 115.9 116.0 G 89.5 141.0 217.4 90.2 89.5 91.0 91.3 76.5 71.6 61.1 5.9
20 3550 22.6 143.4 145.0 G 29.6 66.8 65.7 92.4 91.7 93.3 93.4 89.5 89.6 87.2 2.5
20 1770 23.3 138.4 145.0 G 59.4 130.3 144.0 93.0 92.4 93.6 93.8 86.5 84.3 77.5 4.7
20 1180 25.8 139.9 145.0 G 88.8 127.1 212.7 91.7 91.0 93.1 92.9 79.0 74.3 63.9 7.4
20 875 29.8 136.5 145.0 G 119.8 189.3 261.3 91.0 90.2 91.8 91.2 69.0 60.6 48.9 11.4
25 3555 27.8 183.2 182.5 G 36.9 95.8 93.9 93.0 92.4 93.4 93.1 90.5 89.6 85.4 3.9
25 1775 29.6 177 182.5 G 73.9 125.2 182.5 93.6 93.0 94.0 93.9 84.5 81.5 73.2 6.9
25 1180 32.3 168.8 182.5 G 111.4 204.2 253.6 93.0 92.4 93.3 92.9 78.0 71.9 61.5 9.7
25 875 37 166.4 182.5 G 150.0 235.3 319.7 91.0 90.2 91.9 91.4 69.5 61.7 50.2 13.7

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty
Typical Performance Data cont.

Volts: 460
HP: 0.75 - 250
75% 50%
NP Eff. Guar. 75% 50% NP PF Load Load
Design NEMA B Code FLT LRT BDT Full Eff. Full Load Load Full Power Power Max
HP FL RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff Eff Load Factor Factor KVAR
30 3550 33.2 217.6 217.5 G 44.4 117.1 111.2 93.0 92.4 93.6 93.4 91.0 89.8 85.9 4.5
30 1775 35.1 205.5 217.5 G 88.7 147.8 212.0 93.6 93.0 94.1 94.2 85.5 82.4 74.7 7.8
30 1175 38.2 201.3 217.5 G 133.8 252.2 302.6 93.0 92.4 93.6 93.3 79.0 72.9 62.8 11.1
30 890 42.2 188.5 217.5 G 177.2 243.3 384.3 92.4 91.7 93.9 93.3 72.0 64.1 52.4 15.1
40 3575 46.8 276.8 290.0 G 58.8 94.1 148.9 94.1 93.6 94.0 92.9 85.0 77.3 68.0 12.0
40 1785 50.8 279.9 290.0 G 117.8 205.5 273.4 94.5 94.1 94.5 93.9 78.0 71.1 60.0 16.4
40 1185 49.4 270.9 290.0 G 176.9 274.0 441.1 94.1 93.6 94.6 94.2 80.5 73.9 63.3 14.8
40 890 55.9 254.2 290.0 G 236.4 336.8 518.3 93.0 92.4 94.1 93.5 72.0 64.3 52.5 20.1
50 3570 57.3 342.7 362.5 G 73.5 126.7 183.2 94.5 94.1 94.6 93.8 86.5 80.0 71.6 13.2
50 1780 63.9 341.0 362.5 G 147.4 256.1 332.2 94.5 94.1 94.6 94.1 77.5 70.7 59.7 20.6
50 1185 62.2 333.3 362.5 G 221.3 344.7 543.6 94.1 93.6 94.7 94.5 80.0 73.9 63.3 18.4
50 885 66.6 340.5 362.5 G 297.3 455.4 768.9 93.0 92.4 94.2 93.8 75.5 68.0 56.2 22.8
60 3570 70.4 376.7 435.0 G 88.3 116.7 207.4 95.0 94.5 94.8 93.9 84.0 76.2 66.7 18.4
60 1780 71.2 407.3 435.0 G 177.1 359.6 443.2 95.0 94.5 95.1 94.7 83.0 77.6 67.9 19.5
60 1190 72.5 401.9 435.0 G 264.3 383.8 607.8 95.0 94.5 95.1 94.6 81.5 76.2 66.4 20.1
60 885 78.9 409.1 435.0 G 356.8 560.0 927.6 93.0 92.4 94.5 94.2 76.5 68.7 57.1 26.5
75 3580 85.2 517.2 542.5 G 110.1 158.8 304.5 95.8 95.4 95.6 94.8 86.0 78.5 69.0 21.6
3.24
75 1785 86.6 513.1 542.5 G 220.8 347.0 552.4 95.4 95.0 95.7 95.5 85.0 80.7 72.1 21.0
75 1190 89.6 483.8 542.5 G 330.5 477.3 730.0 95.0 94.5 95.4 95.0 82.5 77.7 68.7 23.1
75 890 94 482.2 542.5 G 442.2 616.5 1019.6 94.5 94.1 95.2 94.7 79.0 73.1 62.9 27.6
100 3570 108 707.2 725.0 G 147.0 241.5 384.8 95.4 95.0 95.7 95.5 91.0 87.1 82.0 17.4
X$D ULTRA® 841

100 3570 108 707.2 725.0 G 147.0 241.5 384.8 95.4 95.0 95.7 95.5 91.0 87.1 82.0 17.4
100 1785 119 587.6 725.0 G 293.9 427.5 668.7 95.8 95.4 96.0 95.8 82.0 76.7 67.0 32.9
100 1195 116 684.8 725.0 G 440.2 590.2 1070.7 95.4 95.0 95.4 94.8 84.5 79.6 71.0 29.0
100 890 125 644.3 725.0 G 590.0 848.7 1371.3 94.5 94.1 95.3 94.9 79.0 72.9 62.7 37.0
125 3580 139 809.4 907.5 G 183.3 220.9 474.2 95.4 95.0 95.8 95.3 88.0 82.0 74.3 29.9
125 3580 136 789.1 907.5 G 183.3 236.9 462.1 95.4 95.0 96.0 95.6 90.0 85.7 80.0 23.8
125 1780 144 723.1 907.5 G 368.4 625.3 865.9 95.8 95.4 95.8 95.4 85.0 80.9 72.8 34.2
125 1190 150 850.7 907.5 G 550.7 977.6 1296.8 95.4 95.0 95.5 95.0 81.5 76.2 66.5 41.6
125 890 155 829.6 907.5 G 737.7 1125.9 1813.5 95.0 94.5 95.4 95.1 79.5 73.5 63.5 45.0
150 3580 163 997.9 1085.0 G 220.0 315.0 577.7 95.8 95.4 96.3 95.9 90.0 85.6 79.6 29.1
150 3580 162 1009.8 1085.0 G 219.9 329.0 584.3 95.8 95.4 96.3 96 90.5 86.5 81 27.4
150 1790 170 1033.2 1085.0 G 439.7 523.1 1157.0 96.2 95.8 96.5 96.1 86.0 81.6 73.2 40.7
150 1195 171 1030.6 1085.0 G 660.4 1001.9 1755.9 95.8 95.4 95.8 95.5 85.5 81.1 73.0 40.2
150 890 184 978.0 1085.0 G 885.0 1338.5 2104.7 95.0 94.5 95.8 95.6 80.5 75.3 65.9 49.4
200 3580 214 1320.7 1450.0 G 293.3 430.9 816.9 95.8 95.4 95.8 95.3 91.5 88.3 84.1 31.5
200 3580 214 1377.3 1450.0 G 293.2 452.5 851.9 95.8 95.4 95.9 95.4 91.5 88.3 83.8 32.2
200 1790 220 1312.4 1450.0 G 586.1 717.7 1493.0 96.5 96.2 96.8 96.5 88.0 84.9 78.3 44.2
200 1190 229 1343.0 1450.0 G 881.0 1343.0 2294.0 95.8 95.4 96.0 95.8 85.5 81.6 73.8 51.7
200 890 247 1380.0 1450.0 G 1181.0 1954.0 3018.0 95.4 95.0 95.7 95.5 79.5 73.7 63.6 71.6
250 3575 265 1556.9 1825.0 G 366.9 561.2 949.0 95.8 95.4 96.1 95.9 92.0 89.8 86.9 32.6
250 3575 265 1556.9 1825.0 G 366.9 561.2 949.0 95.8 95.4 96.1 95.9 92.0 89.8 86.9 32.6
250 1790 280 1636.6 1825.0 G 732.7 898.6 1859.0 96.2 95.8 96.1 95.5 87.0 83.6 76.5 59.9

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
TEFC- Extra Severe Duty
Typical Performance Data
Volts: 575
HP: 1 - 250
75% 50%
NP Eff. Guar. 75% 50% NP PF Load Load
Design NEMA B Code FLT LRT BDT Full Eff. Full Load Load Full Power Power Max
HP FL RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff. Eff. Load Factor Factor KVAR
1 3510 1.1 10.7 12.0 N 1.5 4.9 6.7 87.5 86.5 89.7 88.2 81.0 74.4 62.4 0.4
1 1155 1.5 8.9 12.0 N 4.5 15.1 18.7 82.5 81.5 83.1 80.3 61.5 52.3 40.0 0.9
1 870 1.8 8.6 12.0 N 6.0 11.2 19.5 80.0 78.5 79.3 75.2 52.0 43.6 33.0 1.2
1.5 3495 1.6 15.1 16.0 M 2.2 7.2 9.5 87.5 86.5 89.6 88.7 81.0 74.2 61.8 0.6
1.5 1735 1.7 13.5 16.0 M 4.5 17.9 20.9 86.5 85.5 87.8 86.4 77.5 69.5 56.5 0.8
1.5 1170 1.9 13.9 16.0 M 6.7 14.5 29.4 87.5 86.5 88.3 86.4 67.5 59.2 46.4 1.0
1.5 870 2.6 12.5 16.0 M 9.0 18..0 28.1 80.0 78.5 80.5 76.9 54.0 45.2 34.3 1.7
2 1725 2.2 16.5 20.0 L 6.1 22.1 25.5 86.5 85.5 88.0 87.3 80.0 72.7 60.0 0.9
2 1170 2.5 19.0 20.0 L 9..0 20.8 40.5 88.5 87.5 88.8 87.2 68.0 59.4 46.5 1.3
2 875 3.0 16.1 20.0 L 11.9 21.0 37.4 86.5 85.5 85.8 83.3 57.5 49.4 37.9 1.9
3 3525 3.1 21.0 25.6 K 4.5 9.4 14.2 89.5 88.5 91.3 90.8 82.0 76.5 65.3 1.0
3 1760 3.3 23.5 25.6 K 8.9 22.7 30.2 89.5 88.5 89.7 88.8 75.5 68.5 56.0 1.5
3 1175 3.4 25.3 25.6 K 13.4 33.4 45.8 89.5 88.5 89.7 88.4 73.0 65.8 53.2 1.7
3 870 4.3 22.7 25.6 K 18.0 32.2 51.9 86.5 85.5 86.3 84.6 60.5 52.6 40.7 2.5
5 3535 4.9 36.0 36.8 J 7.4 17.5 24.6 90.2 89.5 91.1 90.2 84.5 79.7 69.7 1.5
5 1755 5.3 34.4 36.8 J 15.0 34.3 43.8 89.5 88.5 90.5 90.1 79.5 74.3 63.5 2.0
5 1170 5.4 35.8 36.8 J 22.4 49.5 64.8 89.5 88.5 90.6 90.2 77.5 72.1 60.6 2.2
5 880 6.5 35.4 36.8 J 29.7 49.3 85.5 89.5 88.5 89.9 88.3 64.5 56.1 43.6 3.5
3.25
7.5 3535 6.8 48.1 50.8 H 11.1 23.0 30.7 91.0 90.2 91.4 90.8 91.0 89.0 83.5 1.6
7.5 1770 7.2 48.2 50.8 H 22.3 40.8 60.4 91.7 91.0 92.1 91.7 85.0 81.9 73.9 2.2
7.5 1175 7.8 48.5 50.8 H 33.5 62.0 92.2 91.7 91.0 92.1 91.6 78.5 73.0 62.1 2.9

X$D ULTRA® 841

7.5 880 9.2 47.1 50.8 H 44.8 67.7 113.4 89.5 88.5 90.1 89.3 68.0 60.5 47.9 4.6
10 3525 9.0 61.5 64.8 H 14.9 31.4 38.9 91.0 90.2 91.9 91.8 91.5 90.6 86.3 1.8
10 1765 9.6 62.7 64.8 H 29.7 54.3 78.6 91.7 91.0 92.3 92.2 85.0 82.0 74.2 2.9
10 1170 10.5 62.9 64.8 H 44.8 82.1 120.6 91.0 90.2 91.7 91.5 78.5 73.4 62.4 3.9
10 885 11.0 60.8 64.8 H 59.5 77.1 146.4 90.2 89.5 91.1 91.0 75.5 70.2 59.3 4.2
15 3550 14.0 84.8 92.8 G 22.2 38.9 50.0 91.7 91.0 92.5 92.2 87.5 86.1 81.0 2.8
15 1770 14.4 85.6 92.8 G 44.5 95.0 109.9 92.4 91.7 93.0 93.0 84.5 81.4 72.8 4.3
15 1180 15.6 84.9 92.8 G 66.6 97.4 158.6 91.7 91.0 92.5 92.3 78.5 73.8 63.2 5.7
15 880 16.3 89.5 92.8 G 89.5 120.6 220.4 90.2 89.5 91.1 91.3 76.5 71.7 61.2 5.9
20 3550 18.1 109.6 116.0 G 29.6 59.3 61.8 92.4 91.7 93.4 93.5 89.5 89.6 87.2 2.5
20 1770 18.6 111.3 116.0 G 59.4 131.2 142.9 93.0 92.4 93.7 93.9 86.5 84.0 77.0 4.8
20 1180 20.7 111.6 116.0 G 88.9 130.6 209.5 91.7 91.0 92.7 92.7 79.0 74.5 64.1 7.4
20 875 23.9 107.7 116.0 G 119.8 183.0 256.9 91.0 90.2 91.6 90.9 69.0 60.6 48.9 11.4
25 3550 22.2 137.2 146.0 G 36.9 87.6 88.8 93.0 92.4 93.4 93.1 90.5 89.6 85.5 3.8
25 1775 23.7 132.7 146.0 G 73.9 135.2 166.4 93.6 93.0 94.2 94.0 84.5 81.4 73.0 7.0
25 1180 25.8 138.5 146.0 G 111.4 209.7 260.2 93.0 92.4 93.3 92.8 78.0 71.3 60.6 10.0
25 875 30.7 148.6 146.0 G 149.5 263.9 355.9 91.0 90.2 91.4 90.4 67.0 58.1 46.2 15.7

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty
Typical Performance Data cont.

Volts: 575
HP: 1 - 250
75% 50%
NP Guar. 75% 50% NP PF Load Load
Design NEMA B Code FLT LRT BDT Eff. Full Eff. Full Load Load Full Power Power Max
HP FL RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff. Eff. Load Factor Factor KVAR
30 3550 26.7 166.0 174 G 44.4 109.6 107.3 93.0 92.4 93.7 93.5 90.5 89.8 85.7 4.5
30 1775 28.2 153.6 174 G 88.7 159.2 192.7 93.6 93.0 94.3 94.3 85.0 82.4 74.6 7.8
30 1180 30.6 159.0 174 G 133.8 245.6 298.8 93.0 92.4 93.5 93.2 79.0 72.9 62.8 11.1
30 890 33.8 150.7 174 G 177.2 242.9 383.6 92.4 91.7 93.8 93.2 72.0 64.1 52.4 15.1
40 3570 37.4 221.3 232 G 58.8 94.1 148.8 94.1 93.6 94.0 92.9 85.0 77.4 68.1 11.9
40 1780 40.6 224.2 232 G 117.8 205.8 273.7 94.5 94.1 94.5 93.9 78.0 71.0 59.9 16.5
40 1185 39.8 217.7 232 G 176.9 275.5 443.0 94.1 93.6 94.6 94.2 80.0 73.8 63.1 14.9
40 890 45.0 210.4 232 G 236.3 349.0 535.5 93.0 92.4 94.0 93.3 71.5 62.9 51.0 21.1
50 3570 45.5 266.7 290 G 73.5 123.2 178.6 94.5 94.1 94.6 93.9 87.0 80.7 72.7 12.6
50 1780 51.1 274.0 290 G 147.4 257.5 333.7 94.5 94.1 94.6 94.1 77.5 70.5 59.4 20.8
50 1185 49.7 270.4 290 G 221.2 349.4 550.4 94.1 93.6 94.6 94.4 80.0 73.4 62.6 18.9
50 885 53.0 267.3 290 G 297.4 446.0 753.8 93.0 92.4 94.2 93.8 76.0 68.5 56.8 22.4
60 3570 56.3 301.0 348 G 88.3 116.7 206.9 95.0 94.5 94.7 93.9 84.0 76.3 66.9 18.4
60 1780 56.6 318.7 348 G 177.2 353.6 434.2 95.0 94.5 95.1 94.8 83.5 78.1 68.6 19.0
60 1190 58.0 321.5 348 G 264.3 383.6 607.2 95.0 94.5 95.1 94.6 81.5 76.2 66.4 20.1
60 880 63.1 319.5 348 G 357.0 544.9 903.3 93.0 92.4 94.4 94.2 76.5 69.3 57.9 25.9
75 3580 68.6 419.5 434 G 110.0 160.7 308.5 95.8 95.4 95.6 94.8 85.5 78.0 68.4 22.0
3.26 75 1785 68.9 407.4 434 G 220.8 344.8 548.7 95.4 95.0 95.8 95.6 85.5 80.8 72.4 20.7
75 1190 71.2 382.2 434 G 330.5 470.5 720.4 95.0 94.5 95.3 95.0 83.0 78.0 69.2 22.7
75 890 75.2 385.1 434 G 442.2 615.3 1017.8 94.5 94.1 95.2 94.7 79.0 73.1 63.0 27.5
100 3570 86.3 565.0 580 G 147.0 247.5 383.2 95.4 95.0 95.8 95.6 91.0 87.4 82.5 17.0
X$D ULTRA® 841

100 1785 95.3 478.7 580 G 293.9 433.7 678.3 95.8 95.4 96.0 95.7 82.0 76.2 66.2 33.7
100 890 100.0 500.7 580 G 590.2 822.4 1330.7 94.5 94.1 95.3 94.9 79.0 73.6 63.7 35.8
125 3580 112.0 663.9 726 G 183.3 226.6 485.6 95.4 95.0 95.8 95.2 87.5 81.4 73.3 31.0
125 1780 115.0 598.3 726 G 368.2 649.0 894.1 95.8 95.4 95.8 95.3 85.0 80.2 71.6 35.7
125 1190 120.0 670.6 726 G 550.7 961.9 1276.9 95.4 95.0 95.5 95.0 82.0 76.6 67.1 40.8
125 890 124.0 663.5 726 G 737.7 1125.4 1812.6 95.0 94.5 95.4 95.1 79.5 73.5 63.5 45.0
150 3580 130.0 807.5 868 G 219.9 314.0 585.2 95.8 95.4 96.3 95.9 90.0 85.2 78.9 30.0
150 1790 137.0 831.2 868 G 439.7 515.7 1162.5 96.2 95.8 96.5 96.0 85.5 80.6 71.8 42.7
150 1190 137.0 815.4 868 G 660.4 989.7 1739.0 95.8 95.4 95.9 95.6 85.5 81.3 73.3 39.7
150 890 147.0 776.2 868 G 885.2 1328.1 2089.9 95.0 94.5 95.8 95.6 80.5 75.4 66.1 49.1
200 3580 170.0 1050.3 1160 G 293.4 442.6 808.1 95.8 95.4 95.9 95.4 92.0 88.7 84.8 30.2
200 1790 175.0 1034.1 1160 G 586.2 706.9 1471.8 96.5 96.2 96.8 96.5 88.5 85.2 78.8 43.4
200 1190 183.0 1054.4 1160 G 881.1 1316.3 2249.4 95.8 95.4 96.0 95.8 85.5 81.9 74.4 50.6
250 3575 211.0 1264.0 1460 G 366.9 578.1 960.0 95.8 95.4 96.2 95.9 92.5 89.9 86.9 32.6
250 1790 224.0 1335.0 1460 G 732.6 913.0 1893.2 96.2 95.8 96.1 95.5 87.0 83.2 75.9 61.5

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 841
TEFC- Extra Severe Duty
Dimensions

Dimensions refer to drawing on following page.

Cast Iron Construction/Frames 140-449, Type KS, 3-Phase/Dimensions – For Estimating Only.
Dimensions in Inches
Approx.
Shaft Mounting(18)
Net
Weight Key
Frame in lbs Width Depth Length N-W U
(1)
V E H BA BS 2F 2XF A B C D(3) G J K L O
143T 43 0.187 0.187 1.380 2.25 0.8748 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
145T 50 0.187 0.187 1.380 2.25 0.8748 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
182T 76 0.250 0.250 1.750 2.75 1.1250 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
184T 101 0.250 0.250 1.750 2.75 1.1250 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
213T 200 0.312 0.312 2.380 3.38 1.3750 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
215T 220 0.312 0.312 2.380 3.38 1.3750 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
254T 315 0.375 0.375 2.380 4.00 1.6250 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
256T 350 0.375 0.375 2.880 4.00 1.6250 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
284TS 460 0.375 0.375 1.880 3.25 1.6250 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
284T 460 0.500 0.500 3.250 4.62 1.8750 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
286TS 510 3.750 3.750 1.880 3.25 1.6250 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
286T 510 0.500 0.500 3.250 4.62 1.8750 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
324TS 664 0.500 0.500 2.000 3.75 1.8750 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 29.04 8.00 0.99 2.01 3.62 15.54 17.07
324T 664 0.500 0.500 3.880 5.25 2.1250 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
326TS 800 0.500 0.500 2.000 3.75 1.8750 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
326T 800 0.500 0.500 3.880 5.25 2.1250 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 32.04 8.00 0.99 2.01 3.62 15.54 17.07 3.27
364TS 1122 0.500 0.500 2.000 3.75 1.8750 3.50 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 32.76 9.00 1.09 2.26 3.40 17.00 19.02
364T 1122 0.625 0.625 4.250 5.88 2.3750 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02
365TS 1155 0.500 0.500 2.000 3.75 1.8750 3.50 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 32.76 9.00 1.09 2.26 3.40 17.00 19.02
365T 1155 0.625 0.625 4.250 5.88 2.3750 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02

X$D ULTRA® 841

404TS 1580 0.500 0.500 2.750 4.25 2.1250 4.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 36.76 10.00 1.29 2.64 4.00 19.02 21.18
404T 1580 0.750 0.750 5.625 7.25 2.8750 7.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 39.77 10.00 1.29 2.64 4.00 19.02 21.18
405TS 1600 0.500 0.500 2.750 4.25 2.1250 4.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 36.76 10.00 1.29 2.64 4.00 19.02 21.18
405T 1600 0.750 0.750 5.625 7.25 2.8750 7.00 8.00 0.81 6.62 6.88 13.75 12.25 18.00 16.00 39.77 10.00 1.29 2.64 4.00 19.02 21.18
444TS 2100 0.625 0.625 3.000 4.75 2.3750 4.50 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 41.87 11.00 1.49 2.64 4.97 21.37 23.94
444T 2100 0.875 0.875 6.875 8.50 3.3750 8.25 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 45.62 11.00 1.49 2.64 4.97 21.37 23.94
445TS 2260 0.625 0.625 3.000 4.75 2.3750 4.50 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 41.87 11.00 1.49 2.64 4.97 21.37 23.94
445T 2260 0.875 0.875 6.875 8.50 3.3750 8.25 9.00 0.81 7.50 8.25 16.50 14.50 20.00 18.80 45.62 11.00 1.49 2.64 4.97 21.37 23.94
447TS 2610 0.625 0.625 3.000 4.75 2.3750 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.37 11.00 1.49 2.64 8.81 25.62 23.94
447T 2610 0.875 0.875 6.875 8.50 3.3750 8.25 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 54.12 11.00 1.49 2.64 8.81 25.62 23.94
449TS(19) 3010 0.625 0.625 3.000 4.75 2.3750 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.37 11.00 1.49 2.64 8.81 25.62 23.94
449T 3010 0.875 0.875 6.875 8.50 3.3750 8.25 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 54.12 11.00 1.49 2.64 8.81 25.62 23.94
1. Shaft diameters 1 1/2 inches and smaller will come within the limits of +0.000 inch, -0.0005 inch diameters 1 5/8 inches and larger +0.000 inch, -0.001 inch.
3. Tolerance on “D” dimension for rigid base motors will be +0.000 inch, -0.060 inch. No tolerance has been est. for the “D” dimension of resilient mounted motors.
18. Motor feet have 2 holes per foot allowing NEMA F-1 or F-2 assembly while maintaining critical NEMA mounting dimensions.
19. Cast iron motors in 449 frame also have mounting holes meeting 447 frame dimensions.
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward, or from either side. Weights shown are approximate shipping
weights and should be used for estimating only.

Data subject to change without notice. GEP-500S 02/08. www.gemotors.com

 X$D ULTRA® 841
TEFC- Extra Severe Duty
Dimensions cont.
Frame dimensions on previous page.

Cast Iron Construction/Frames 140-449, Type KS, 3-Phase/Dimensions – For Estimating Only.

Conduit Box Dimensions

Approx. Dimensions in Inches
Frame Nominal Hp
3.28 Vol. AA* AB AC AF XL XN
143-145 2 32 0.75 6.62 5.12 2.50 4.30 5.40
182-184 5 32 0.75 7.82 6.32 2.50 4.30 5.40
213-215 10 55 1.00 9.50 7.42 3.50 5.78 4.16
X$D ULTRA® 841

254-256 20 140 1.25 11.68 9.12 4.59 7.37 5.37

284-286 30 140 1.50 12.44 9.88 4.59 7.37 5.37
324-326 50 346 3.00 16.13 12.43 6.44 10.14 7.00
364-365 75 346 3.00 17.07 13.37 6.44 10.14 7.00
404-405 125 700 3.00 20.48 16.22 7.00 12.13 10.50
444-449 200 700 3.00 22.00 17.74 7.00 12.13 10.50
444-449 250-300 1500** 4.00 22.30 180.50 8.12 13.74 17.15
* A tapped NPT hole is provided for the conduit size listed in Column AA
** Fabricated steel

C-Face Dimensions
All Dimensions in inches
Key Key Key
NEMA Frame AH AJ AK U Width Thickness Length
143TC-145TC 2.12 5.88 4.50 0.875 0.19 0.19 1.38
182TC-184TC 2.62 7.25 8.50 1.125 0.25 0.25 1.75
213TC-215TC 3.12 7.25 8.50 1.375 0.31 0.31 2.38
254TC-256TC 3.75 7.25 8.50 1.625 0.38 0.38 2.88
284TC-286TC 4.38 9.00 10.50 1.875 0.50 0.50 3.25

www.gemotors.com Data subject to change without notice. GEP-500S 02/08.

 X$D ULTRA® 661
TEFC- Extra Severe Duty
GEGARD2400 TM
INVERTER
DUTY
Heat Exchanger
EXCEEDS
NEMA

Standard Features
MG1-31

HP Range 5-75
Poles 4 pole
Voltage 460
Efficiency Meets or exceeds NEMA Premium nominal. Exceeds all NEMA Premium minimum efficiencies.
Frequency 60 Hz
NEMA Design B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 1940 ISO Grade 1.0, Roller Bearings: 4P: 0.0004 in (P-P)
Bearing Caps Cast iron and gasketed on both ends
Bearing Housing Rise 4 pole: 45ºC
Bearing Protection Complete motor IP55 protection
Bearing Type Roller Bearing on DE only. Ball bearing on ODE
Conduit Box Gasketed & rotatable, and Cast Iron
Div 2 Temp Codes NEMA Design B motors have an Auto Ignition Temperature of 200 degree C stamped on the
nameplate. A Division 2 Nameplate can be provided (see kit section).
Drains Stainless Steel T-drains in lowest section of both endshields
End Shield Cast Iron
Fan Non-Sparking Plastic
Fan Cover Cast Iron 3.29
Fasteners SAE, Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 inches

X$D ULTRA® 661

Frame Material Cast Iron
Frame Size 184-365
Grease Polyurea
Ground Ground Lug in Conduit Box and Frame Ground
Industry Specifications Meets IEEE 45 Marine Duty, Meets GM 7E-TA Automotive Duty, Meets API 661 specification
Insulation Class Class H for 320 frame & larger, all others Class F with H materials
Insulation System GEGARD2400TM 320-449 frames. GEGARD2000TM 140-280 frames. Non-Hygroscopic,
Anti-Fungus, 2400Volt or 2000Volt @ .1microsecond rise time. Exceeds NEMA MG1-31
Inverter Capabilities Variable Torque inf:1
L10 Bearing Life Belted: 40,000 hrs
Lifting Means 4 Lugs cast into frame
Mounting Stocked as W8 (shaft up) and field modified to W6 (shaft down)
Mounting Holes 1 per foot (324 frame), 2 per foot (all other frames)
Nameplate Stainless Steel Includes Weight, 3/4 Load Efficiency, Vibration Limit
Oil Mist Lube Includes provisions for conversion to Oil Mist Lubrication
Paint Buff, Epoxyester
Relubrication Both ends, extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15
Shaft TIR Meets IEEE 841, .001 in for shaft diameter 1.625 in and smaller, .0015 in for shaft diameter
greater than 1.625 in.
Special Painting Meets IEEE 841
Tach Mounting Tach kits for field modifications are available
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine Report including Vibration supplied with motor, IEEE 112
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 60 months in service or 66 months from date of manufacturing, whichever occurs first
 X$D ULTRA® 661
TEFC- Extra Severe Duty GEGARD2400 TM
INVERTER
DUTY

Heat Exchanger EXCEEDS

NEMA
MG1-31

Pricing

Volts: 460
HP: 5 - 75
Nom Guar. Cat List Wt. C Dim.
HP RPM Volts Frame FLA Eff Min Eff No. Price Price Symbol Norm Stk (lbs) (in) Notes
5 1800 460 184T 6.6 89.5 88.5 M6621 $1,315 G4-7UXHE N 101 15.90 117
7.5 1800 460 213T 9.1 91.7 91.0 M6622 $1,710 G4-7UXHE N 200 20.10
10 1800 460 215T 12.0 91.7 91.0 M6623 $1,789 G4-7UXHE N 220 20.10
15 1800 460 254T 18.0 92.4 91.7 M6624 $2,122 G4-7UXHE N 315 25.60
20 1800 460 256T 23.3 93.0 92.4 M6625 $2,439 G4-7UXHE Y 350 25.60
25 1800 460 284T 29.8 93.6 93.0 M6626 $2,842 G4-7UXHE Y 460 28.58
30 1800 460 286T 35.5 93.6 93.0 M6627 $3,250 G4-7UXHE Y 510 28.58
40 1800 460 324T 50.8 94.5 94.1 M6628 $4,465 G4-7UXHE Y 689 30.54
50 1800 460 326T 63.9 94.5 94.1 M6629 $5,029 G4-7UXHE N 740 32.04
60 1800 460 364T 71.2 95.0 94.5 M6630 $7,556 G4-7UXHE N 1020 34.89 118
60 1800 460 364T 71.2 95.0 94.5 M6631 $7,556 G4-7UXHE N 1020 34.89 119
75 1800 460 365T 86.6 95.4 95.0 M6632 $8,779 G4-7UXHE N 1090 34.89 118
75 1800 460 365T 86.6 95.4 95.0 M6633 $8,779 G4-7UXHE N 1090 34.89 119
Notes
117 Ball bearing
118 W6 (shaft down) is standard mount and not field modifiable to W8 (shaft up)
119 W8 (shaft up) is standard mount and not field modifiable to W6 (shaft down)
3.30
X$D ULTRA® 661

Drip Cover Kits

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A1201 249A4267AD-G01 140 $105 G4-7KITS Y
A1202 249A4267AD-G02 180 $110 G4-7KITS Y
A1203 249A4267AD-G03 210 $125 G4-7KITS Y
A1204 249A4267AD-G04 250 $136 G4-7KITS Y
A1205 249A4267AD-G05 280 $155 G4-7KITS Y
A1206 249A4267AD-G06 320 $173 G4-7KITS Y

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® 661
GEGARD2400 TM
INVERTER
TEFC- Extra Severe Duty
DUTY
EXCEEDS
NEMA
MG1-31 Heat Exchanger
Typical Performance Data

Volts: 460
HP: 5 - 75
75% 50%
NP Guar. 75% 50% NP PF Load Load
Design NEMA B Code FLT LRT BDT Eff. Full Eff. Full Load Load Full Power Power Max
HP FL RPM NP FLA LRA LRA KVA/HP (lb-ft) (lb-ft) (lb-ft) Load Load Eff. Eff. Load Factor Factor KVAR
5 1755 6.6 43.1 46.0 J 15.0 34.4 43.8 89.5 88.5 90.5 90.1 79.5 74.2 63.4 2.0
7.5 1770 9.1 62.8 63.5 H 22.3 42.6 62.9 91.7 91.0 92.2 91.6 84.5 81.1 72.5 2.3
10 1765 12.1 81.0 81.0 H 29.7 56.0 80.8 91.7 91.0 92.4 92.1 84.5 81.4 73.2 3.0
15 1770 18.0 108.4 116.0 G 44.5 96.4 111.3 92.4 91.7 93.1 93.0 84.5 81.1 72.4 4.3
20 1770 23.3 139.9 145.0 G 59.4 132.1 143.5 93.0 92.4 93.7 93.9 86.5 84.0 76.9 4.8
25 1775 29.6 164.9 182.5 G 73.9 134.4 165.5 93.6 93.0 94.2 94.0 84.5 81.5 73.2 6.9
30 1775 35.3 191.6 217.5 G 88.7 158.7 192.3 93.6 93.0 94.3 94.3 85.0 82.4 74.7 7.8
40 1780 49.5 271.7 290.0 G 117.8 201.3 265.5 94.5 94.1 94.7 94.2 80.0 74.1 63.8 14.6
50 1775 62.5 355.5 362.5 G 148.0 290.7 342.1 93.6 93.0 94.2 93.8 80.0 77.6 68.4 18.8
60 1785 69.5 416.7 435.0 G 176.5 275.0 448.7 95.0 94.5 95.7 95.3 85.0 80.5 71.9 16.9
75 1785 86.6 513.1 542.5 G 220.8 347.0 552.4 95.4 95.0 95.7 95.5 85.0 80.7 72.1 21.0

3.31

X$D ULTRA® 661

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® 661
TEFC- Extra Severe Duty
Heat Exchanger
Dimensions

Cast Iron Construction/Frames 184-365, Type KS, 3-Phase/Dimensions – For Estimating Only.

3.32 Dimensions in Inches

Approx.
Net Shaft Mounting (18)
Weight Key
Frame in lbs Width Depth Length N-W U
(1)
V E H BA BS 2F 2XF A B C D(3) G J K L O
184T 101 0.250 0.250 1.750 2.75 1.1250 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
X$D ULTRA® 661

213T 200 0.312 0.312 2.380 3.38 1.3750 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
215T 220 0.312 0.312 2.380 3.38 1.3750 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
254T 315 0.375 0.375 2.380 4.00 1.6250 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
256T 350 0.375 0.375 2.880 4.00 1.6250 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
284T 460 0.500 0.500 3.250 4.62 1.8750 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
286T 510 0.500 0.500 3.250 4.62 1.8750 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
324T 664 0.500 0.500 3.880 5.25 2.1250 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
326T 800 0.500 0.500 3.880 5.25 2.1250 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 32.04 8.00 0.99 2.01 3.62 15.54 17.07
364T 1122 0.625 0.625 4.250 5.88 2.3750 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02
365T 1155 0.625 0.625 4.250 5.88 2.3750 5.64 7.00 0.69 5.88 6.13 12.25 11.25 16.00 14.40 43.89 9.00 1.09 2.26 3.40 17.00 19.02
1. Shaft diameters 1 1/2 inches and smaller will come within the limits of +0.000 inch, -0.0005 inch diameters 1 5/8 inches and larger +0.000 inch, -0.001 inch
3. Tolerance on “D” dimension for rigid base motors will be +0.000 inch, -0.060 inch. No tolerance has been est. for the “D” dimension of resilient mounted motors.
18. Motor feet have 2 holes per foot allowing NEMA F-1 or F-2 assembly while maintaining critical NEMA mounting dimensions.
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward, or from either side. Weights shown are approximate shipping
weights and should be used for estimating only.

Conduit Box Dimensions

Nominal Approx. Dimensions in Inches
Frame
HP Vol. AA* AB AC AF XL XN
182-184 5 32 0.75 7.82 6.32 2.50 4.30 5.40
213-215 10 55 1.00 9.50 7.42 3.50 5.78 4.16
254-256 20 140 1.25 11.68 9.12 4.59 7.37 5.37
284-286 30 140 1.50 12.44 9.88 4.59 7.37 5.37
324-326 50 346 3.00 16.13 12.43 6.44 10.14 7.00
364-365 75 346 3.00 17.07 13.37 6.44 10.14 7.00
* A tapped NPT hole is provided for the conduit size listed in Column AA
** Fabricated steel

www.gemotors.com Data subject to change without notice. GEP-500S 02/08.

 X$D ULTRA® Family
Kits and Accessories

C-Face Kits – X$D ULTRA, ULTRA 841, ULTRA 661

Cat No. Part No. Frame List Price Price Symbol Norm Stk
PB14A 4001A5202AAG001 143T - 145T $72 G4-7KITS Y
PB18A 4001A5202AAG002 182T - 184T $98 G4-7KITS Y
PB21A 4001A5202AAG003 213T - 215T $125 G4-7KITS Y
PB25A 4001A5202AAG004 254T - 256T $169 G4-7KITS Y
PB28A 4001A5202AAG005 284T - 286T, 284TS-286TS $224 G4-7KITS Y
A761 249A4321AMG01 324T - 326T $261 G4-7KITS Y
A762 249A4321AMG02 324TS - 326TS $261 G4-7KITS Y
A763 249A4321AMG03 364T - 365T $561 G4-7KITS Y
A764 249A4321AMG04 364TS - 365TS $561 G4-7KITS Y
A765 249A4321AMG05 404T - 405T $590 G4-7KITS Y
A766 249A4321AMG06 404TS - 405TS $590 G4-7KITS Y
A767 249A4321AMG07 444T - 449T $1,408 G4-7KITS Y
A768 249A4321AMG08 444TS - 449TS $1,408 G4-7KITS Y
Note: 143-256 frame will not meet NEMA BA dimension using C-Face kit.
Note: X$D Ultra and X$D Ultra 841 C-Face fits will not have endshield machined for Inpro/Seal.®

D Flange Kits – X$D ULTRA, ULTRA 841, ULTRA 661

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A991 249A4321ARG01 324T-326T $608 G4-7KITS N
A992 249A4321ARG02 324TS-326TS $608 G4-7KITS N
A993 249A4321ARG03 364T-365T $1,028 G4-7KITS N 3.33
A994 249A4321ARG04 364TS-365TS $1,028 G4-7KITS N
A995 249A4321ARG05 404T-405T $1,400 G4-7KITS N

X$D ULTRA® Family - Kits

A996 249A4321ARG06 404TS-405TS $1,400 G4-7KITS N
A997 249A4321ARG07 444T-449T $1,457 G4-7KITS N
A998 249A4321ARG08 444TS-449TS $1,679 G4-7KITS N
Note: X$D Ultra and X$D Ultra 841 D-Flange kits will not have endshield machined for Inpro/Seal.®

Division 2 Nameplate – X$D ULTRA, ULTRA 841, ULTRA 661

As standard an auxiliary tag is provided on X$D Ultra 841 motors which states: “Maximum exposed internal and
external surface temperatures shall not exceed 200 Degree C under usual service conditions (sinewave power) at 1.0
SF.” If required, a UL Div 2 nameplate may be ordered as a custom feature to any X$D Ultra Family of motors. The new
nameplate will exclude the motor capability on a variable frequency drive unless supplied for technical review. Net
price $200 per motor.

Drip Cover Kits – X$D ULTRA, ULTRA 841, ULTRA 661

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A1201 249A4267AD-G01 140 $105 G4-7KITS Y
A1202 249A4267AD-G02 180 $110 G4-7KITS Y
A1203 249A4267AD-G03 210 $125 G4-7KITS Y
A1204 249A4267AD-G04 250 $136 G4-7KITS Y
A1205 249A4267AD-G05 280 $155 G4-7KITS Y
A1206 249A4267AD-G06 320 $173 G4-7KITS Y

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® Family
Kits and Accessories cont.

Ground Terminal Post – X$D ULTRA, ULTRA 841, ULTRA 661

The Ground Terminal Post replaces a bolt on the drive-end endshield allowing for an external frame ground
Cat No. Part No. Frame List Price Price Symbol Norm Stk
A340 4001A5921CYG006 140 $68 G4-7KITS Y
A341 4001A5921CYG001 180-250 $68 G4-7KITS Y
A342 4001A5921CYG002 280 $68 G4-7KITS Y
A343 249A4234AAG20 320 $68 G4-7KITS Y
A344 249A4234AAG03 360-400 $68 G4-7KITS Y
A345 249A4234AAG21 440 $68 G4-7KITS Y
A346 249A4234AAG07 500 $68 G4-7KITS Y

Low Profile Inpro/Seal® Kits – X$D ULTRA, ULTRA 841, ULTRA 661
Cat No. Part No. Frame List Price Price Symbol Norm Stk
A1001 4002B5914ANP001 140T - 145T $145 G4-7KITS N
A1002 4002B5914ANP002 182T - 184T $145 G4-7KITS Y
A1003 4002B5914ANP003 213T-215T $158 G4-7KITS Y
A1004 4002B5914ANP004 254T-256T $190 G4-7KITS Y
A1005 4002B5914ANP005 284T-286T, 284TS-286TS $246 G4-7KITS Y
A826 235A4575GE001 324T-326T $109 G4-7KITS Y
A1007 235A4575GS1 324TS-326TS $336 G4-7KITS Y
A828 235A4575GE003 364TS-449TS, 364T-365T $140 G4-7KITS Y
3.34
A830 235A4575GE005 404T-405T $459 G4-7KITS Y
A832 235A4575GE007 444T-449T $549 G4-7KITS Y
X$D ULTRA® Family - Kits

Space Heater Kits – X$D ULTRA, ULTRA 841, ULTRA 661

Cat No. Frame Volts List Price Price Symbol Norm Stk
A233 182-184 110-120 $107 G4-7KITS N
A239 182-184 220-240 $107 G4-7KITS N
A234 213-326 110-120 $111 G4-7KITS N
A235 213-326 220-240 $111 G4-7KITS Y
A236 213-326 440-480 $111 G4-7KITS N
A237 364-405 110-120 $188 G4-7KITS N
A238 364-405 200-208, 220-240 $188 G4-7KITS N
A240 364-405 440-480 $188 G4-7KITS N
A241 444-449 110-120 $203 G4-7KITS Y
A242 444-449 200-208, 220-240 $203 G4-7KITS N
A244 444-449 440-480 $203 G4-7KITS N
Includes insulation and strip heater.
No separate heater nameplate furnished. The existing motor nameplate is to be stamped with heater volts and watts.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 X$D ULTRA® Family
Kits and Accessories cont.

Thermostatically Controlled Space HeaterKits (Division II Applications) – X$D ULTRA, ULTRA 841, ULTRA 661
GE has developed and patented a thermostatically controlled space heater. These heaters operate with a maximum surface
temperature of 140 degrees C and are provided with a hermetically sealed thermostat so they do not spark in an end of life event.
In most cases when a motor is shut down, the space heaters are immediately turned on. As the motor may take many hours to
cool down, the heaters being automatically turned on can result in a cumulative heat that may result in temperatures that
approach the 80% Auto-Ignition Temperature (A.I.T.) limit. A thermostatically controlled heater will not allow the heater to
energize until the motor has sufficiently cooled down (below 140C thermostat reset temperature) thereby not allowing the
temperatures to exceed the stated AIT.

Cat No. Part No. Frame Voltage List Price Price Symbol Norm Stk
A284 235A4753BF1 182-184 110-120 $339 G4-7KITS Y
A285 235A4753BF2 182-184 220-240 $339 G4-7KITS Y
A286 235A4753BF4 182-184 440-480 $339 G4-7KITS Y
A287 235A4753BG1 213-286 110-120 $405 G4-7KITS Y
A288 235A4753BG2 213-286 220-240 $405 G4-7KITS Y
A289 235A4753BG3 213-286 440-480 $405 G4-7KITS Y
A290 235A4753BH1 324-405 110-120 $405 G4-7KITS Y
A291 235A4753BH2 324-405 220-240 $405 G4-7KITS Y
A292 235A4753BH3 324-405 440-480 $405 G4-7KITS Y
A293 235A4753BJ1 444-449 110-120 $480 G4-7KITS Y
A294 235A4753BJ2 444-449 220-240 $480 G4-7KITS Y
A295 235A4753BJ3 444-449 440-480 $480 G4-7KITS Y
A296 235A4753BK1 509-5013 110-120 $550 G4-7KITS Y
A297 235A4753BK2 509-5013 220-240 $550 G4-7KITS Y
A298 235A4753BK3 509-5013 440-480 $550 G4-7KITS Y 3.35

X$D ULTRA® Family - Kits

Sliding Bases for 215-364 Frame Motors
Bases are suitable for the indicated frame size and is suitable for the majority of floor-mounted, belt-connected motors. These
bases are not suitable for ceiling or side-wall mounting installations. The 213-215 frame size bases are closed frame construction
with two adjusting screws. The 254-364 frame size bases are open frame construction with two adjusting screws.

Frame Part No. Cat No. List Price Price Symbol Norm Stk
213 249A9598AA1 A100 $60 GO-1R Y
215 249A9598AA2 A101 $60 GO-1R Y
254 249A9598AA3 A102 $71 GO-1R Y
256 249A9598AA4 A103 $71 GO-1R Y
284 249A9598AA5 A104 $91 GO-1R Y
286 249A9598AA6 A105 $91 GO-1R Y
324 249A9598AA7 A106 $105 GO-1R Y
326 249A9598AA8 A107 $105 GO-1R Y
364 249A9598AA9 A108 $186 GO-1R Y

Thermostat Kit – X$D ULTRA, ULTRA 841, ULTRA 661

Cat No. Temperature Class Opening Temperature List Price Price Symbol Norm Stk
A337 F 155-165C $89 G4-7KITS N
Thermostat leads are 29" long with terminals.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 X$D ULTRA® Family
Checklist for Value

Complete Test per MG1 Part 12 IEEE Standard 112, Test Method B Single shielded bearings on both ends open towards the grease
on 2% of all production. Verification of compliance and routine test cavity allowing maximum opportunity for grease circulation within
report supplied with every X$D Ultra motor. the confines of the GE Six Star Bearing System.

Charged lube system with Polyurea grease decreases the potential 130,000 hour L10 direct connected and 50,000 hour L10a belted
for contaminants in the lubricant. bearing life increases up-time and decreases repair costs.

Dual mounting holes provide for application versatility and reduce Oversized gasketed conduit box reduces the possibility of moisture
inventory. in the conduit box.

Four point cast-in lifting lugs eliminate lost eye bolts and make Precision Plus balance to .04 ips results in smooth, reliable
mounting easier and safer. operation and extends bearing life.

X$D Ultra motors include the elements necessary to field install Cast iron bearing cap with gasket retains lubricant and protects
shaft-mounted encoders for closed loop drive applications. the interior of the motor and the bearing system from
contaminants.
All stock X$D Ultra motors can be UL listed for Division II locations.
New finned endshield for improved heat dissipation and long
Brass combination breather/drains allow condensation to drain bearing life.
from motor.
Non-sparking corrosion resistant fan is quiet and energy efficient.
Three year performance and mechanical warranty (36/42 month)
is standard. This comprehensive warranty program covers both Premium efficiency lowers annual energy cost and extends motor
mechanical and efficiency performance. life without any sacrifice in NEMA B performance.

Rugged cast iron frame, conduit box and fan cover are resistant to Increased air gap on 324 through 449 frames achieves higher
process industry environments for extended motor life. efficiencies without exceeding NEMA B starting currents.
3.36
Epoxyester paint system stands up to corrosive environments and GEGARD2000 insulation system is manufactured with Class H
meets the IEEE 841 paint requirements. materials and is designed to exceed the IGBT requirements of
NEMA MG1-31.
X$D ULTRA® Family

Rigid and recessed severe-duty shaft slinger provides bearing

system protection. Field modifiable to a non-contact rotating seal Extended grease fittings and grease filler tubes charged with
on the drive-end. Polyerea grease make maintenance safer and easier.

Corrosion resistant SAE Grade 5 hardware is rugged and designed ISO 1940 Grade 1.0 Precision Plus balance for low vibration.
for ease of the motor service.
Temperature resistant Polyurea bearing grease suitable for
Grease fittings and plugs provide relubrication access to extend temperatures of -40 to +130° C.
bearing life.
Fan covers on frames 324 through 449 are designed with axial
Embossed 316 stainless steel nameplate stamped with superior mounting bolts to ensure a more rugged installation.
operational and maintenance information.Permanently labeled,
non-wicking Class F leads make connections and installation easy. Grounding terminal in conduit box adds to safety during
installation and service.
Lead gasket and conduit box cover gasket prevent moisture and
contaminants from entering motor. Stator core centered in the frame enabling conversion to
F2 mounting.
Cast-in vibration pads provide five point vibration probe mounting
locations (four radial and one axial). Low temperature rise design increases bearing life.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Adjustable Speed Motor – A$D

Standard Features

HP Range 1.5-300
Poles 4
Voltage 460
Frequency 60 Hz
NEMA Design A
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration .055 IPS
Bearing Caps Both ends. 143-286: ODE is gasketed, 324-449: both ends are gasketed
Bearing Protection Recessed Slinger, Inpro Seal kit available
Bearing Type Ball
Centered Core Allows F1-F2 field conversion
Conduit Box Gasketed and rotatable, Fabricated Steel above 250 Amps, All other: Cast iron
Cooling 143-182: Non-Vent, 184-449: Totally Enclosed Fan Cooled, 364-449:
Blower Cooled also available.
DE Mounting 143-286: Nema C-face mount
Drains Brass T-drains
End Shield Cast Iron
Fan Non-Sparking Plastic or Bronze
Fan Cover Cast Iron
Fasteners SAE, Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 inches
Frame Material Cast Iron
Frame Size 143-449
Grease Polyurea
Ground Ground lug in Conduit Box
Insulation Class F (Class H materials with Class F leads)
Insulation System Non-Hygroscopic, Anti-Fungus, meets NEMA MG1-31 4.1
Inverter Capabilities Variable Torque inf:1, Constant Torque inf:1

Adjustable Speed Motor – A$D

L10 Bearing Life Direct Coupled: 130,000 hrs, Belted: 26,280 hrs, Belted L10a 50,000
Lifting Means 143-286: 4 Lugs cast into frame, 324-449: 2 Lugs cast into frame
Mounting F1
Mounting Holes 2 per foot
Nameplate Stainless Steel Includes Weight, Vibration Limit, Service Factor, Speed Range Constant Torque
and Constant HP
Paint Gray, Epoxyester
Relubrication Both ends, extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.0
Shaft TIR Meets IEEE 841, .001 in for shaft diameter 1.625 in and smaller, .0015 in for shaft diameter
greater than 1.625 in.
Tach Mounting ODE C-face provision for tach mounting. 143-184: 4.5" rabbet, 213-449: 8.5" rabbet
Temperature Rise 80°C @ 1.0 SF sine wave power, 105°C PWM power
Tests NEMA Routine Report including Vibration supplied with motor, IEEE 112
Thermal Protection 140-280, 2 NC Thermostats; 320-449, 3 NC Thermostats
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 12 months from date of purchase or 18 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Adjustable Speed Motor – A$D

Pricing
Volts: 230/460, 460
HP: 1.5-300
A$D Totally Enclosed – Infinite: 1 Constant Torque Speed Range
SF on Nom Price Norm Wt C Dim
HP RPM Volts Frame Drive Base Prot FLA Eff Cat No List Price Symbol Stk (lbs) (in) Notes
1.5 1800 230/460 143TC 1 Ftd Tstats 4.6/2.3 85.5 S2053 $724 G4-7AS N 43 14.82 55
2 1800 230/460 145TC 1 Ftd Tstats 5.8/2.9 85.5 S2054 $780 G4-7AS Y 43 14.82 55
3 1800 230/460 182TC 1 Ftd Tstats 7.8/3.9 85.5 S2055 $1,274 G4-7AS Y 76 15.39 55
5 1800 230/460 184TC 1 Ftd Tstats 12.8/6.4 85.5 S2056 $1,424 G4-7AS Y 101 17.78
7.5 1800 230/460 213TC 1 Ftd Tstats 18.6/9.3 91.7 S2057 $1,665 G4-7AS Y 200 22.36
10 1800 230/460 215TC 1 Ftd Tstats 25.0/12.5 91.7 S2058 $1,760 G4-7AS Y 220 22.36
15 1800 230/460 254TC 1 Ftd Tstats 37.6/18.8 92.4 S2059 $2,397 G4-7AS Y 315 27.68
20 1800 230/460 256TC 1 Ftd Tstats 51.2/25.6 93.0 S2060 $2,930 G4-7AS Y 350 27.68
25 1800 230/460 284TC 1 Ftd Tstats 58.8/29.4 94.1 S2061 $3,312 G4-7AS Y 460 33.64
30 1800 230/460 286TC 1 Ftd Tstats 70.2/35.1 94.1 S2062 $3,787 G4-7AS Y 510 33.64
40 1800 230/460 324T 1 Ftd Tstats 101.6/50.8 93.6 S2063 $4,128 G4-7AS N 690 37.38
50 1800 230/460 326T 1 Ftd Tstats 124.2/62.1 94.1 S2064 $4,666 G4-7AS N 740 37.38
60 1800 230/460 364T 1 Ftd Tstats 148.5/74.3 94.1 S2065 $6,014 G4-7AS N 1040 41.37 121
60 1800 230/460 364T 1 Ftd Tstats 134.4/67.2 94.1 S2073 $6,600 G4-7AS N 1060 41.37 40,121
75 1800 230/460 365T 1 Ftd Tstats 187.0/93.5 94.1 S2066 $6,813 G4-7AS N 1070 41.37 121
75 1800 230/460 365T 1 Ftd Tstats 168.8/84.4 94.5 S2074 $7,890 G4-7AS N 1070 41.37 40,121
100 1800 230/460 405T 1 Ftd Tstats 218.0/109.0 95.4 S2067 $9,219 G4-7AS N 1560 43.51 121
100 1800 460 405T 1 Ftd Tstats 106.5 95.8 S2075 $11,014 G4-7AS N 1560 43.51 40,121
125 1800 460 444T 1 Ftd Tstats 135.0 95.0 S2068 $11,988 G4-7AS N 2050 50.69 40,121
125 1800 460 405T 1 Ftd Tstats 133.3 95.8 S2076 $13,890 G4-7AS N 1560 43.51 40,121
150 1800 460 445T 1 Ftd Tstats 160.0 95.4 S2069 $13,863 G4-7AS N 2050 50.69 103,121
150 1800 460 445T 1 Ftd Tstats 160.3 95.8 S2077 $15,765 G4-7AS N 2050 50.87 40,103,121
200 1800 460 445T 1 Ftd Tstats 216.0 95.8 S2070 $16,764 G4-7AS N 2050 50.69 103,121
200 1800 460 445T 1 Ftd Tstats 213.8 95.8 S2078 $18,666 G4-7AS N 2050 50.87 40,103,121
250 1800 460 449T 1 Ftd Tstats 266.0 96.5 S2071 $20,917 G4-7AS N 2830 59.19 103,121
250 1800 460 449T 1 Ftd Tstats 268.2 96.2 S2079 $23,417 G4-7AS N 2870 59.38 40,103,121
300 1800 460 449T 1 Ftd Tstats 336.0 96.5 S2072 $23,837 G4-7AS N 3110 63.78 103,121
4.2 300 1800 460 449T 1 Ftd Tstats 304.3 96.5 S2080 $26,337 G4-7AS N 2890 59.38 40,103,121
Notes
Adjustable Speed Motor – A$D

40 TEBC - Totally Enclosed Blower Cooled

55 TENV Construction
103 Insulated ODE bearing and shaft ground brush on DE
121 Opposite drive end C-face and stub shaft

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Adjustable Speed Motor – A$D

Motor Dimensions

Dimensions are listed on pages 4.4 and 4.5.

Frames 143-182 Totally Enclosed Non-Ventilated (TENV) with Accessory Mounting Face

1/2"-13UNC-2B (4)
.83 MIN. FULL THD. AB C4
EQ. SPACED 45∞ OFF
C/L ON ÿ7.25 WHEN AC L N-W
COVER REMOVED
MOUNTING
P XN V
FACE
KEY

O AF
XL
D
G ÿU

SHAFT COVER
AA HOLE
J FOR CONDUIT K BS

E E H HOLE 2XF

A 2F BA

Frames 184-449 Totally Enclosed Fan Cooled (TEFC) with Accessory Mounting Face

AB C4

AC ACCESSORY L N-W
MOUNTING
P FACE XN V
KEY

AF
XL O
G
D
ÿU

AA HOLE
J FOR CONDUIT K BS
E E SEE ENLARGED 2XF
H HOLE
A DETAIL
2F BA
(COVER MUST
BE REMOVED) B 4.3

Adjustable Speed Motor – A$D

Frames 364-449 Totally Enclosed Blower Cooled (TEBC) with Accessory Mounting Face

AB C4
AIR INLET AC L

P YB
YC N-W

YH HOLE
(FAR SIDE)
ACCESSORY KEY .500 SQ
MOUNTING X 2.75 LONG
O
FACE
YA
AF
XL XN
D G
ÿU

AA HOLES K
J FOR CONDUIT
BS
E E H HOLE
2XF
A SEE ENLARGED 2F BA
DETAIL
(COVER MUST B
BE REMOVED)

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Adjustable Speed Motor – A$D

Motor Dimensions cont.

Dimensions correspond to figures on page 4.3.

TEFC Dimensions
Shaft Mounting25
Net Keyway
Wt. Key
Frame Lbs. W D Length N-W U19 V20 E H BA BS 2F 2XF A B C GD21 J K L O P
143TC 43 0.187 0.0935 1.38 2.13 0.88 2.12 2.75 0.37 2.75 2.50 - 4.00 6.88 5.88 14.82 3.50 0.40 1.39 2.32 7.31 7.25 7.34
145TC 43 0.187 0.0935 1.38 2.13 0.88 2.12 2.75 0.37 2.75 2.50 5.00 6.88 5.88 14.82 3.50 0.40 1.39 2.32 7.31 7.25 7.34
182TC 76 0.25 0.1250 1.75 2.75 1.12 2.50 3.75 0.41 2.75 2.75 - 4.50 8.68 6.64 18.46 4.50 0.53 1.54 2.58 9.45 9.25 9.50
184TC 101 0.25 0.1250 1.75 2.75 1.12 2.50 3.75 0.41 2.75 2.75 5.50 - 8.68 6.64 20.86 4.50 0.53 1.54 2.58 11.86 9.57 9.92
213TC 200 0.31 0.1560 2.38 3.38 1.38 3.12 4.25 0.42 3.50 3.50 - 5.50 9.60 8.00 25.50 5.25 0.61 1.47 2.82 14.37 11.00 11.37
215TC 220 0.31 0.1560 2.38 3.38 1.38 3.12 4.25 0.42 3.50 3.50 7.00 - 9.60 8.00 25.50 5.25 0.61 1.47 2.82 14.37 11.00 11.37
254TC 315 0.38 0.1900 2.88 4.00 1.62 3.75 5.00 0.53 4.25 5.00 - 5.28 11.20 11.30 30.82 6.25 0.71 1.52 3.93 17.07 12.88 13.25
256TC 350 0.38 0.1900 2.88 4.00 1.62 3.75 5.00 0.53 4.25 5.00 10.00 - 11.20 11.30 30.82 6.25 0.71 1.52 3.93 17.07 12.88 13.25
284TC 460 0.5 0.2500 3.25 4.62 1.88 4.38 5.50 0.53 4.75 5.50 - 9.50 12.40 12.80 33.64 7.00 0.80 1.75 4.12 18.76 14.29 14.50
286TC 510 0.5 0.2500 3.25 4.62 1.88 4.38 5.50 0.53 4.75 5.50 11.00 - 12.40 12.80 33.64 7.00 0.80 1.75 4.12 18.76 14.29 14.50
324T 685 0.5 0.1900 3.88 5.25 2.12 5.00 6.25 0.66 5.25 6.00 - 10.50 14.40 13.80 37.38 8.00 1.00 1.97 3.63 20.88 16.44 17.14
326T 740 0.5 0.1900 3.88 5.25 2.13 5.00 6.25 0.66 5.25 6.00 12.00 - 14.40 13.80 37.38 8.00 1.00 1.97 3.63 20.88 16.44 17.14
364T 965 0.5 0.2500 4.25 5.88 2.38 5.62 7.00 0.69 5.88 6.12 - 11.25 16.00 14.40 41.37 9.00 1.10 2.30 3.48 23.48 18.38 19.42
365T 1070 0.5 0.2500 4.25 5.88 2.38 5.62 7.00 0.69 5.88 6.12 12.25 - 16.00 14.40 41.37 9.00 1.10 2.30 3.48 23.48 18.38 19.42
405T 1560 0.75 0.3750 5.62 7.25 2.88 7.00 8.00 0.81 6.62 6.88 13.75 - 18.00 16.00 43.51 10.00 1.30 2.56 4.25 22.77 20.83 21.74
444T 2050 0.875 0.4400 6.88 8.50 3.38 8.25 9.00 0.81 8.25* 8.25 - 14.50 20.00 18.80 50.69 11.00 1.50 2.61 4.90 25.69 22.98 24.22
445T 2050 0.875 0.4400 6.88 8.50 3.38 8.25 9.00 0.81 8.25* 8.25 16.50 - 20.00 18.80 50.69 11.00 1.50 2.61 4.90 25.69 22.98 24.22
449T26 2830 0.875 0.4400 6.88 8.50 3.38 8.25 9.00 0.81 8.25* 12.50 25.00 - 20.00 27.30 55.44 11.00 1.50 2.61 8.91 29.94 22.98 24.22
449T 3110 0.875 0.4400 6.88 8.50 3.38 8.25 9.00 0.81 8.25* 12.50 25.00 - 20.00 27.30 63.78 11.00 1.50 2.61 8.91 47.04 22.98 24.22

TEBC Dimensions
Shaft Mounting25
Net Keyway
Wt. Key
Frame Lbs. W D Length N-W U19 V20 E H BA BS 2F 2XF A B C D21 G J K L O P
364T 965 0.500 0.250 2.00 5.88 2.38 5.62 7.00 0.69 5.88 6.12 - 11.25 16.00 14.40 41.37 9.00 1.10 2.30 3.48 23.38 18.38 19.42
4.4 365T 1025 0.500 0.250 2.00 5.88 2.38 5.62 7.00 0.69 5.88 6.12 12.30 - 16.00 14.40 41.37 9.00 1.10 2.30 3.48 23.38 18.38 19.42
404T 1410 0.500 0.250 2.75 7.25 2.88 7.00 8.00 0.81 6.62 6.88 - 12.25 18.00 16.00 43.51 10.00 1.30 2.56 4.25 22.77 20.38 21.74
Adjustable Speed Motor – A$D

405T 1600 0.500 0.250 2.75 7.25 2.88 7.00 8.00 0.81 6.62 6.88 13.80 - 18.00 16.00 43.51 10.00 1.30 2.56 4.25 22.77 20.38 21.74
444T 1750 0.620 0.310 3.00 8.50 3.38 8.25 9.00 0.81 7.50 8.25 - 14.50 20.00 18.80 50.69 11.00 1.50 2.61 4.90 25.69 22.98 24.22
445T 2000 0.620 0.310 3.00 8.50 3.38 8.25 9.00 0.81 7.50 8.25 16.50 - 20.00 18.80 50.69 11.00 1.50 2.61 4.90 25.69 22.98 24.22
449T26 2650 0.880 0.440 3.00 8.50 3.38 8.25 9.00 0.81 7.50 12.50 25.00 - 20.00 37.30 55.44 11.00 1.50 2.61 8.91 29.94 22.98 24.22

Notes
19 Shaft diameters 1.5 inches and smaller will come within the limits of +0.000 inch -0.0005 inch;
diameters 1.625 inches and larger +0.000 inch -0.001 inch
20 Dimension “V” represents length of straight part of shaft extension
21 Tolerance on “D” dimension will be: On frames 182T-362T +0.000 inch -0.032 inch.
On frames 364T-449T +0.000inch -0.060 inch

25 Motor feet have 2 holes = per foot allowing NEMA F-1 or F-2 assembly while maintaining critical NEMA dimensions.
26 Cast iron motors in 449 frame also have mounting holes meeting 447 frame dimensions.
39 See Accessory Mounting Face Outline.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Adjustable Speed Motor – A$D

Motor Dimensions cont.

Dimensions correspond to figures on page 4.3.

Conduit Box Dimensions

Normal Max. Fl Approx.
Frame HP40 Amps Volume AA BB AC23 AF XL XN
182-184 5 - 32 0.75 7.93 6.43 2.50 4.30 3.44
213-215 10 - 32 1.00 8.63 7.13 2.50 4.30 3.44
254-256 20 - 76 1.25 10.52 8.37 3.62 5.94 4.38
284-286 30 - 137 1.50 12.35 9.76 4.59 7.38 5.38
324-326 50 - 346 2.00 15.25 11.63 6.44 10.12 7.00
364-365 75 - 346 3.00 16.43 12.81 6.44 10.12 7.00
404-405 100 - 700 3.00 19.31 15.81 7.00 11.75 10.00
444-449 300 - 700 3.00 20.63 16.50 7.00 11.75 10.00
Notes
23 Insulated ODE bearing and shaft ground brush on DE
40 Conduit box size is determined by full load amps. Nominal horsepower is stated as a reference only.
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward,
downward or from either side.

Blower Dimensions
Frame YA YB YC YE YH
364-365 24.87 14.29 3.75 3.57 0.875
404-405 27.96 16.45 3.67 0.84 0.875
444-449 31.98 20.08 3.67 2.44 1.094
509-5013 35.55 20.08 3.67 2.44 1.094

C-Face Mounting
All Dimensions in inches
Key Key Key
NEMA Frame AH AJ AK U Width Thickness Length
143TC-145TC 2.12 5.88 4.50 0.875 0.19 0.19 1.38
182TC-184TC 2.62 7.25 8.50 1.125 0.25 0.25 1.75
213TC-215TC 3.12 7.25 8.50 1.375 0.31 0.31 2.38 4.5
254TC-256TC 3.75 7.25 8.50 1.625 0.38 0.38 2.88

Adjustable Speed Motor – A$D

284TC-286TC 4.38 9.00 10.50 1.875 0.50 0.50 3.25

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Adjustable Speed Motor – A$D

Kits and Accessories

C-Face Kits
Part No. Frame Poles Cat No. List Price Price Symbol Norm Stk
249A4321AMG01 324-326T 4-6 A735 $261 G6-7KITS N
249A4321AMG03 364-365T 4-6 A736 $439 G6-7KITS Y
249A4321AMG05 404-405T 4-6 A737 $575 G6-7KITS Y
249A4321AMG07 444-445T 4-6 A739 $575 G6-7KITS Y

Encoder Kits
Part No. Frame Brand Cat No. List Price Price Symbol Norm Stk
180 - 449 Avtron Contact Factory for Price and Availability
235A4985APG01 182 - 326 Dynapar HS35 A543 $1,027 G4-7KITS N
235A4985ANG01 182 - 326 Lakeshore SL85 A544 $1,842 G4-7KITS N
235A4985ARG01 364 - 449 Dynapar HS35 A542 $1,027 G4-7KITS N
235A4985ANG04 364 - 449 Lakeshore SL85 A545 $1,842 G4-7KITS N

Inpro-Seal® Kits
Part No. Frame Cat. No. List Price Price Symbol Norm Stk
4002B5914ANP001 140T - 145T A1001 $145 G4-7KITS N
4002B5914ANP002 182T - 184T A1002 $145 G4-7KITS Y
4002B5914ANP003 213T-215T A1003 $158 G4-7KITS Y
4002B5914ANP004 254T-256T A1004 $190 G4-7KITS Y
4002B5914ANP005 284T-286T A1005 $246 G4-7KITS Y
235A4575GE001 320T A826 $109 G4-7KITS Y
235A4575GE003 360T A828 $140 G4-7KITS Y
235A4575GE005 400T A830 $459 G4-7KITS Y
235A4575GE007 440T A832 $549 G4-7KITS N

4.6 Space Heater Kits

Part No. Frame Volts Cat No. List Price Price Symbol Norm Stk
Adjustable Speed Motor – A$D

153B1073BEG01 182-184 110-120 A233 $107 G4-7KITS N

153B1073BDG02 182-184 220-240 A239 $107 G4-7KITS N
153B1069AAG01 213-326 110-120 A234 $111 G4-7KITS N
153B1069AAG02 213-326 220-240 A235 $111 G4-7KITS Y
153B1069AAG03 213-326 440-480 A236 $111 G4-7KITS N
153B1069ANG01 364-405 110-120 A237 $188 G4-7KITS N
153B1069ANG05 364-405 200-208, 220-240 A238 $188 G4-7KITS N
128D6204AB1 364-405 440-480 A240 $188 G4-7KITS N
153B1069ANG02 444-449 110-120 A241 $203 G4-7KITS Y
153B1069ANG06 444-449 200-208, 220-240 A242 $203 G4-7KITS N
153B1069ANG04 444-449 440-480 A244 $203 G4-7KITS N

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW
3Q tr 08 A$D ULTRA®

Standard Features

HP Range 1.5-300
Poles 4
Voltage 230/460, 460
Frequency 60 Hz
NEMA Design A
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.055 IPS
Bearing Caps Both ends. 143-286: O.D.E. is gasketed, 324-449: both ends are gasketed
Bearing Protection Neoprene steel reinforced recessed slinger, non-contact labrynth seal kit available, insulated
O.D.E. bearing with shaft grounding brush 444-449 frame
Bearing Type Ball bearing, Roller bearing available as an option 360 frame and larger
Centered Core Allows F1-F2 field conversion
Conduit Box Gasketed and rotatable, Fabricated Steel above 250 Amps, All other: Cast iron
Cooling 143-182: Non-Vent, 184-449: Totally Enclosed Fan Cooled, 364-449:
Blower Cooled also available.
Drive End Mounting 143-286: Nema C-face mount
Drains Stainless Steel T-drains in lowest section of both endshields
End Shield Cast Iron
Fan Non-Sparking Plastic or Bronze
Fan Cover Cast Iron
Fasteners SAE, Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 inches
Frame Material Cast Iron
Frame Size 143-449
Grease Polyurea
Ground Ground lug in Conduit Box
Insulation Class F (Class H materials with Class F leads)
Insulation System GEGARD2000TM: Non-Hygroscopic, Anti-Fungus, exceeds NEMA MG1-31 4.7
Inverter Capabilities Variable Torque inf:1, Constant Torque inf:1, Constant HP to 1.5 times base speed
L10 Bearing Life Direct Coupled: 130,000 hrs, Belted: 26,280 hrs, Belted L10a 50,000
Lifting Means 4 lugs cast into frame
Mounting F1

A$D ULTRA®
Mounting Holes 1 per foot (324 frame), 2 per foot (all other frames)
Nameplate Stainless Steel Includes Weight, Vibration Limit, Service Factor, Speed Range Constant Torque
and Constant HP
Paint Gray, Epoxyester
Relubrication Both ends, extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.0
Shaft Total Indicator Meets IEEE 841, 0.001 in for shaft diameter 1.625 in and smaller, 0.0015 in for shaft diameter
Runout greater than 1.625 in.
Tach Mounting O.D.E. C-face provision for tach mounting. 143-184: 4.5" rabbet, 213-449: 8.5" rabbet
Temperature Rise 80°C @ 1.0 SF sine wave power, 105°C inverter power
Tests NEMA Routine Report including vibration supplied with motor, IEEE 112
Thermal Protection 140-280, 2 Normally Closed Thermostats; 320-449, 3 Nornally Closed Thermostats
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 36 months from date of purchase or 42 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 A$D ULTRA® N EW
3 Qtr 08

Pricing
Volts: 230/460, 460
HP: 1.5-300
A$D Totally Enclosed – Infinite: 1 Constant Torque Speed Range
SF on Nom Price C Dim
HP RPM Volts Frame Drive Base Prot FLA Eff Cat No List Price Symbol Norm Stk Wt (lbs) (in) Notes
1.5 1800 230/460 143TC 1.0 Ftd Tstats 4.6/2.3 85.5 M9300 Y 43 14.82 55
2 1800 230/460 145TC 1.0 Ftd Tstats 5.8/2.9 85.5 M9301 Y 43 14.82 55
3 1800 230/460 182TC 1.0 Ftd Tstats 7.8/3.9 85.5 M9302 Y 76 15.39 55
5 1800 230/460 184TC 1.0 Ftd Tstats 12.8/6.4 85.5 M9303 Y 101 17.78
7.5 1800 230/460 213TC 1.0 Ftd Tstats 18.6/9.3 91.7 M9304 Y 200 22.36
10 1800 230/460 215TC 1.0 Ftd Tstats 25.0/12.5 91.7 M9305 Y 220 22.36
15 1800 230/460 254TC 1.0 Ftd Tstats 37.6/18.8 92.4 M9306 Y 315 27.68
20 1800 230/460 256TC 1.0 Ftd Tstats 51.2/25.6 93.0 M9307 Y 350 27.68
25 1800 230/460 284TC 1.0 Ftd Tstats 58.8/29.4 94.1 M9308 Y 460 33.64
30 1800 230/460 286TC 1.0 Ftd Tstats 70.2/35.1 94.1 M9309 Y 510 33.64
40 1800 230/460 324T 1.0 Ftd Tstats 101.6/50.8 93.6 M9310 Y 690 37.38
50 1800 230/460 326T 1.0 Ftd Tstats 124.2/62.1 94.1 M9311 N 740 37.38
60 1800 230/460 364T 1.0 Ftd Tstats 148.5/74.3 94.1 M9312 Available 3 Qtr, Y 1040 41.37
2008. Please
60 1800 230/460 364T 1.0 Ftd Tstats 134.4/67.2 94.1 M9313 contact your sales Y 1060 41.37 40
75 1800 230/460 365T 1.0 Ftd Tstats 187.0/93.5 94.1 M9314 representative N 1070 41.37
for pricing
75 1800 230/460 365T 1.0 Ftd Tstats 168.8/84.4 94.5 M9315 information. N 1070 41.37 40
100 1800 230/460 405T 1.0 Ftd Tstats 218.0/109.0 95.4 M9316 N 1560 43.51
100 1800 460 405T 1.0 Ftd Tstats 106.5 95.8 M9317 N 1560 43.51 40
125 1800 460 444T 1.0 Ftd Tstats 135.0 95.0 M9318 Y 2050 50.69 103
125 1800 460 405T 1.0 Ftd Tstats 133.3 95.8 M9319 Y 1560 43.51 40
150 1800 460 445T 1.0 Ftd Tstats 160.0 95.4 M9320 N 2050 50.69 103
150 1800 460 445T 1.0 Ftd Tstats 160.3 95.8 M9321 N 2050 50.87 40,103
200 1800 460 445T 1.0 Ftd Tstats 216.0 95.8 M9322 N 2050 50.69 103
200 1800 460 445T 1.0 Ftd Tstats 213.8 95.8 M9323 N 2050 50.87 40,103
250 1800 460 449T 1.0 Ftd Tstats 266.0 96.5 M9324 N 2830 59.19 103
250 1800 460 449T 1.0 Ftd Tstats 268.2 96.2 M9325 N 2870 59.38 40,103
300 1800 460 449T 1.0 Ftd Tstats 336.0 96.5 M9326 N 3110 63.78 103
4.8 300 1800 460 449T 1.0 Ftd Tstats 304.3 96.5 M9327 N 2890 59.38 40,103
Notes:
40 TEBC - Totally Enclosed Blower Cooled
55 TENV - Totally Enclosed Non-Ventilated
103 Insulated O.D.E. bearing and shaft ground brush on DE
A$D ULTRA®

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Medium Voltage
Above NEMA (2300/4000 Volts)
Standard Features
5.1

HP Range 250 - 800 500 - 4000

Poles 2, 4 2, 4
Voltage 2300/4000 2300/4000
Efficiency Standard Standard
NEMA Design As noted 650% LRC; 60% LRT; 175% BDT; 1 x NEMA inertia
Altitude 1000 meters 1000 meters
Ambient 40 degree C 40 degree C
Balance/Vibration Standard per NEMA MG1 Standard per NEMA MG1
Bearing Caps Ball Bearing only Ball Bearing only
Bearing Temp Device 100 Platinum RTD both bearings 100 Platinum RTD both bearings (as optional)
Bearing Type Ball or Sleeve as noted Ball or sleeve as noted
Conduit Box 2500 cu in 6300 cu in
Constant Level Oilers Provided on sleeve bearings
Enclosure WPII WPII, TEAAC, TEFC
Cast iron for TEFC; On WPII and TEAAC: Cast iron for ball bear-
End Shield Cast iron
ings; Fabricated steel plates for sleeve bearings
Fasteners SAE Zinc-plated
Frame Material Cast iron Cast iron for TEFC; Fabricated steel plates for WPII and TEAAC
Frame Size 509 - 5011 8210 - 8313 / 7010 - 7011
Frequency 60 Hz 60 Hz
Ground Ground in conduit box and frame Ground in conduit box and frame
Insulation Class Class F Class F
Insulation System Form coil epoxy VPI Form coil epoxy VPI
Inverter Capabilities Consult Factory Consult Factory
Lifting Means Four (4) cast in lifting lugs Lifting lugs (four (4) for WPII and TEAAC); Two (two) for TEFC)
Lubrication Ball bearing Polyurea, Sleeve bearing oil Self-cooled grease lube Ball bearing, Sleeve oil-ring lube
Mounting Foot mounted F1 Foot mounted F1
Mounting Holes One per foot One per foot
Nameplate Stainless Steel Stainless Steel
Paint Epoxyester Gray Epoxy Priner + Polyurethane finish - Munsell 3.5N Dark Gray
Relubrication Yes, both ends Yes, both ends
Roller Bearing Field conversion available
Rotor Aluminum Aluminum or Copper as noted
Service Factor 1.15 1.0
Shaft Material ANSI 1045 ANSI 1045 or 4140 as noted
Thermostatically controlled space heaters, 115 volt,
Space Heater Standard temperature; 120V, 1-phase
200 watt. Leads to a Condulet
Stator Temp Device 100 platinum Stator RTD’s, leads to accessory box 100 platinum Stator RTD’s, leads to accessory box
TEFC Shaft Material ANSI 4140 1800 rpm only
Temperature Rise As noted Class B rise @ 1.0SF
Tests NEMA Routine NEMA Routine
Time Rating Continuous Continuous
Vertical Jack Screws Standard
12 months from date of purchase or 18 months 12 months from date of purchase or 18 months from
Warranty
from date of shipment, whichever comes first. date of shipment,

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Medium Voltage
Above NEMA (2300/4000 Volts)
Pricing and Kits
5.2
Weather Protected II
HP RPM Volts Frame SF FLA Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
400 3600 2300/4000 509LS 1.15 86.4/49.7 S3425 $35,979 G6-7DAN Y 3620 50.65 4,6
400 3600 2300/4000 509LS 1.15 86.4/49.7 S3402 $33,479 G6-7DAN Y 3620 50.65 6
400 1800 2300/4000 509L 1.15 86.4/49.7 S3403 $33,454 G6-7DAN Y 3620 56.90 6
450 3600 2300/4000 509LS 1.15 1800 S3426 $36,904 G6-7DAN Y 3620 50.65 4
450 3600 2300/4000 509LS 1.15 97.2/55.9 S3404 $34,404 G6-7DAN Y 3620 50.65
450 1800 2300/4000 509L 1.15 97.7/56.2 S3405 $34,264 G6-7DAN Y 3620 56.90
500 3600 2300/4000 509LS 1.15 108.2/62.2 S3427 $37,477 G6-7DAN Y 3620 50.65 4
500 3600 2300/4000 509LS 1.15 108.2/62.2 S3406 $34,977 G6-7DAN Y 3620 50.65
500 1800 2300/4000 509L 1.15 109.6/63.0 S3407 $24,296 G6-7DAN Y 3620 56.90
500 1800 2300/4000 5011L 1.15 107.3/61.7 S3408 $37,809 G6-7DAN Y 4710 64.90 6
600 3600 2300/4000 509LS 1.15 132.0/75.9 S3428 $39,186 G6-7DAN Y 3260 50.65 4, 133
600 3600 2300/4000 509LS 1.15 132.0/75.9 S3409 $36,686 G6-7DAN Y 3620 50.65 133
600 3600 2300/4000 5011LS 1.15 127.1/73.1 S3429 $42,541 G6-7DAN Y 4710 58.65 4, 133
600 1800 2300/4000 5011L 1.15 129.2/74.3 S3411 $41,259 G6-7DAN Y 4710 64.90 133
700 3600 2300/4000 5011LS 1.15 149.0/85.7 S3430 $46,155 G6-7DAN Y 4710 58.65 4, 133
700 1800 2300/4000 5011L 1.15 153.0/88.0 S3413 $43,009 G6-7DAN Y 4710 64.90 133
800 3600 2300/4000 5011LS 1.15 172.9/99.4 S3431 $48,659 G6-7DAN Y 4710 58.65 4, 133
Notes
4 Sleeve Bearing
6 NEMA Design A
133 Non-NEMA Electrical Design

Bearing Conversion Kit

Designed to convert drive end ball bearing to roller bearing with the recommended ISO roller bearing. For 509-5011 GE
frames (4, 6 and 8 pole only) stock motors. Roller bearing supplied. Contact factory for eligible models.

Cat No. Part No. Frame List Price Price Symbol Norm Stk
A927 249A4321AGG01 509-5011 $360 G6-7KITS N
Application of this kit requires load confirmation with factory.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Medium Voltage
Pegasus™ MHV - WPII
Pricing
5.3
Pegasus MHV - Weather Protected II
™

HP RPM Volts Frame FLA Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
800 1800 2300/4000 8210 181/104 P100 $100,211 G8-9PWII N 7500 76.50 128, 137
800 1800 2300/4000 8210 181/104 P101 $90,103 G8-9PWII N 7500 76.50 137
900 3600 2300/4000 8210 196/113 P102 $118,501 G8-9PWII N 7000 65.01 128, 137
900 3600 2300/4000 8210 196/113 P103 $108,393 G8-9PWII N 7000 65.01 137
900 1800 2300/4000 8210 201/116 P104 $103,933 G8-9PWII N 7500 76.50 128, 137
900 1800 2300/4000 8210 201/116 P105 $93,825 G8-9PWII N 7500 76.50 137
1000 3600 2300/4000 8212 217/125 P106 $109,523 G8-9PWII N 8500 75.01 137
1000 1800 2300/4000 8210 221/127 P107 $108,588 G8-9PWII N 7500 76.50 128, 137
1000 1800 2300/4000 8210 221/127 P108 $98,482 G8-9PWII N 7500 76.50 137
1250 3600 2300/4000 8212 272/156 P109 $112,912 G8-9PWII N 8500 75.01 137
1250 1800 2300/4000 8212 276/159 P110 $116,039 G8-9PWII N 9200 85.50 128, 137
1250 1800 2300/4000 8212 276/159 P111 $105,932 G8-9PWII N 9200 85.50 137
1500 3600 2300/4000 8212 334/192 P112 $118,563 G8-9PWII N 8500 75.01 137
1500 1800 2300/4000 8212 330/189 P113 $125,351 G8-9PWII N 9200 85.50 128, 137
1500 1800 2300/4000 8212 330/189 P114 $115,245 G8-9PWII N 9200 85.50 137
1750 3600 2300/4000 8213 382/220 P115 $155,397 G8-9PWII N 9300 82.50 114, 128, 137
1750 1800 2300/4000 8311 382/219 P116 $136,806 G8-9PWII N 12000 86.00 128
1750 1800 2300/4000 8311 382/219 P117 $124,678 G8-9PWII N 12000 86.00
2000 3600 2300/4000 8213 431/248 P118 $161,378 G8-9PWII N 9300 82.50 114, 128, 137
2000 1800 2300/4000 8311 446/257 P119 $143,638 G8-9PWII N 12000 86.00 128
2000 1800 2300/4000 8311 446/257 P120 $131,509 G8-9PWII N 12000 86.00
2250 3600 2300/4000 8213 484/279 P121 $170,017 G8-9PWII N 9300 82.50 114, 128, 137
2250 1800 2300/4000 8313 497/286 P122 $170,425 G8-9PWII N 16000 101.00 128
2250 1800 2300/4000 8313 497/286 P123 $157,398 G8-9PWII N 16000 101.00
2500 3600 2300/4000 8313 531/305 P124 $203,839 G8-9PWII N 13900 95.00 114, 128, 137
2500 1800 2300/4000 8313 549/316 P125 $171,892 G8-9PWII N 16000 101.00 128
2500 1800 2300/4000 8313 549/316 P126 $158,866 G8-9PWII N 16000 101.00
2750 1800 2300/4000 8313 602/346 P127 $177,764 G8-9PWII N 16000 101.00 128, 137
2750 1800 2300/4000 8313 602/346 P128 $164,738 G8-9PWII N 16000 101.00 137
3000 3600 2300/4000 8313 636/366 P129 $209,516 G8-9PWII N 13900 95.00 114, 128, 137
3000 1800 2300/4000 8313 656/377 P130 $186,572 G8-9PWII N 16000 101.00 128, 137
3000 1800 2300/4000 8313 656/377 P131 $173,545 G8-9PWII N 16000 101.00 137
3500 3600 2300/4000 8313 741/426 P132 $220,871 G8-9PWII N 13900 95.00 114, 128, 137
3500 1800 2300/4000 8313 763/439 P133 $196,847 G8-9PWII N 16000 101.00 128, 137
3500 1800 2300/4000 8313 763/439 P134 $183,821 G8-9PWII N 16000 101.00 137
4000 3600 2300/4000 8313 847/487 P135 $228,439 G8-9PWII N 13900 95.00 114, 128, 137
Notes
114 Fabricated Copper Bar Rotor
128 Split Sleeve Bearings
137 4140 shaft material

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Medium Voltage
Quantum™ LMV - TEFC
Pricing
5.4
Quantum™ LMV - TEFC
HP RPM Volts Frame FLA Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
900 3600 2300/4000 7010 192/111 Q100 $156,830 G8-9QT N 9700 119.00 128
900 1800 2300/4000 7010 199/112 Q101 $141,244 G8-9QT N 9500 133.50 128
900 1800 2300/4000 7010 199/112 Q102 $129,520 G8-9QT N 9500 121.50
1000 3600 2300/4000 7011 212/122 Q103 $175,454 G8-9QT N 11400 119.00 128
1000 1800 2300/4000 7010 217/126 Q104 $144,827 G8-9QT N 10100 133.50 128
1000 1800 2300/4000 7010 217/126 Q105 $133,103 G8-9QT N 10100 121.50
1250 3600 2300/4000 7011 264/152 Q106 $190,720 G8-9QT N 12500 119.00 128
1250 1800 2300/4000 7010 266/154 Q107 $156,772 G8-9QT N 11000 133.50 128
1250 1800 2300/4000 7010 266/154 Q108 $145,046 G8-9QT N 11000 121.50
1350 3600 2300/4000 7011 284/164 Q109 $204,474 G8-9QT N 13000 119.00 128
1350 1800 2300/4000 7011 290/167 Q110 $165,882 G8-9QT N 12100 133.50 128
1350 1800 2300/4000 7011 290/167 Q111 $153,754 G8-9QT N 12100 121.50
1500 3600 2300/4000 7011 318/184 Q112 $205,985 G8-9QT N 13600 119.00 128
1500 1800 2300/4000 7011 320/185 Q113 $167,515 G8-9QT N 12700 133.50 128
1500 1800 2300/4000 7011 320/185 Q114 $155,792 G8-9QT N 12700 121.50
1750 1800 2300/4000 7011 375/214 Q115 $208,756 G8-9QT N 14100 133.50 114, 128, 137
1750 1800 2300/4000 7011 375/214 Q116 $197,032 G8-9QT N 14100 121.50 114, 137
2000 1800 2300/4000 7011 430/245 Q117 $221,521 G8-9QT N 15000 133.50 114, 128, 137
2000 1800 2300/4000 7011 430/245 Q118 $209,797 G8-9QT N 15000 121.50 114, 137
Notes
114 Fabricated Copper Bar Rotor
128 Split Sleeve Bearings
137 4140 shaft material

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Medium Voltage
Pegasus™ MHV - TEAAC
Pricing
5.5
Pegasus MHV - TEAAC
™

HP RPM Volts Frame FLA Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
500 3600 2300/4000 8210 110/63 P200 $139,035 G8-9PTAC N 8100 83.26 128, 137
500 3600 2300/4000 8210 110/63 P201 $128,927 G8-9PTAC N 8100 83.26 137
600 3600 2300/4000 8210 132/76 P202 $140,136 G8-9PTAC N 8100 83.26 128, 137
600 3600 2300/4000 8210 132/76 P203 $130,030 G8-9PTAC N 8100 83.26 137
600 1800 2300/4000 8208 133/76 P204 $120,897 G8-9PTAC N 7000 90.50 128, 137
600 1800 2300/4000 8208 133/76 P205 $110,791 G8-9PTAC N 7000 90.50
700 3600 2300/4000 8210 153/88 P206 $141,240 G8-9PTAC N 8100 83.26 128, 137
700 3600 2300/4000 8210 153/88 P207 $131,134 G8-9PTAC N 8100 83.26 137
700 1800 2300/4000 8210 155/89 P208 $122,740 G8-9PTAC N 8750 101.00 128
700 1800 2300/4000 8210 155/89 P209 $112,634 G8-9PTAC N 8750 101.00
800 3600 2300/4000 8210 175/100 P210 $141,240 G8-9PTAC N 8100 83.26 128, 137
800 3600 2300/4000 8210 175/100 P211 $131,134 G8-9PTAC N 8100 83.26 137
800 1800 2300/4000 8210 177/102 P212 $124,123 G8-9PTAC N 8750 101.00 128
800 1800 2300/4000 8210 177/102 P213 $114,017 G8-9PTAC N 8750 101.00
900 3600 2300/4000 8212 197/114 P214 $156,830 G8-9PTAC N 9950 93.26 137
900 1800 2300/4000 8210 200/115 P215 $141,244 G8-9PTAC N 8750 101.00 128, 137
900 1800 2300/4000 8210 200/115 P216 $129,520 G8-9PTAC N 8750 101.00 137
1000 3600 2300/4000 8212 219/126 P217 $175,454 G8-9PTAC N 9950 93.26 137
1000 1800 2300/4000 8212 220/126 P218 $144,827 G8-9PTAC N 10500 101.00 128, 137
1000 1800 2300/4000 8212 220/126 P219 $133,103 G8-9PTAC N 10500 101.00 137
1250 3600 2300/4000 8212 271/156 P220 $190,720 G8-9PTAC N 9950 93.26 137
1250 1800 2300/4000 8212 273/157 P221 $156,772 G8-9PTAC N 10500 101.00 128, 137
1250 1800 2300/4000 8212 273/157 P222 $145,046 G8-9PTAC N 10500 101.00 137
1500 3600 2300/4000 8213 326/187 P223 $205,985 G8-9PTAC N 11500 102.00 114, 128, 137
1500 1800 2300/4000 8212 326/187 P224 $167,515 G8-9PTAC N 10500 101.00 128, 137
1500 1800 2300/4000 8212 326/187 P225 $155,792 G8-9PTAC N 10500 101.00 137
1750 3600 2300/4000 8213 380/218 P226 $174,407 G8-9PTAC N 11500 102.00 114, 128, 137
1750 1800 2300/4000 8311 393/226 P227 $208,756 G8-9PTAC N 13500 112.00 128
1750 1800 2300/4000 8311 393/226 P228 $197,032 G8-9PTAC N 13500 112.00
2000 3600 2300/4000 8213 433/249 P229 $178,023 G8-9PTAC N 12500 102.00 114, 128, 137
2000 1800 2300/4000 8313 444/255 P230 $221,521 G8-9PTAC N 17500 130.00 128
2000 1800 2300/4000 8313 444/255 P231 $209,797 G8-9PTAC N 17500 130.00
2250 3600 2300/4000 8313 483/278 P232 $218,111 G8-9PTAC N 13500 117.00 114, 128, 137
2250 1800 2300/4000 8313 500/287 P233 $179,625 G8-9PTAC N 17500 130.00 128
2250 1800 2300/4000 8313 500/287 P234 $166,596 G8-9PTAC N 17500 130.00
2500 3600 2300/4000 8313 535/308 P235 $226,383 G8-9PTAC N 13500 117.00 114, 128, 137
2500 1800 2300/4000 8313 547/315 P236 $186,974 G8-9PTAC N 17500 130.00 128
2500 1800 2300/4000 8313 547/315 P237 $173,947 G8-9PTAC N 17500 130.00
2750 1800 2300/4000 8313 601/346 P238 $194,323 G8-9PTAC N 17500 130.00 128, 137
2750 1800 2300/4000 8313 601/346 P239 $181,296 G8-9PTAC N 17500 130.00 137
3000 3600 2300/4000 8313 640/368 P240 $229,691 G8-9PTAC N 14000 117.00 114, 128, 137
3000 1800 2300/4000 8313 656/377 P241 $201,674 G8-9PTAC N 17500 130.00 128, 137
3000 1800 2300/4000 8313 656/377 P242 $188,647 G8-9PTAC N 17500 130.00 137
Notes
114 Fabricated Copper Bar Rotor
128 Split Sleeve Bearings
137 4140 shaft material

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Medium Voltage
Above NEMA (2300/4000 Volts)
Dimensions
5.6
Weather Protected II
500 Frame

Dimensions in Inches
Shaft Mounting
Approx. Keyway
Net Wt. Key
Frame In Lbs. Width Depth Length N-W U1 V2 BA D3 E F H A B C G J K L O P
509L 3300 1.000 0.500 10.0 12.00 3.875 11.75 8.5 12.5 10 14.0 1.06 26 32.6 56.90 1.1 5 6.5 22.40 45.26 42.2
509LS 3300 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 14.0 1.06 26 32.6 50.65 1.1 5 6.5 22.40 45.26 42.2
509LL 3300 0.875 0.437 5.0 6.75 3.375 6.50 8.5 12.5 10 14.0 1.06 26 32.6 51.65 1.1 5 6.5 22.40 45.26 42.2
5011L 4100 1.000 0.500 10.0 12.00 3.875 11.75 8.5 12.5 10 18.0 1.06 23 40.6 64.90 1.1 5 6.5 26.40 45.26 42.2
5011LS 4100 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 18.0 1.06 26 40.6 58.65 1.1 5 6.5 26.40 45.26 42.2
5011LL 4100 0.875 0.437 5.0 6.75 3.375 6.50 8.5 12.5 10 18.0 1.06 26 40.6 59.65 1.1 5 6.5 26.40 45.26 42.2
5013ST 5350 0.750 0.375 4.0 5.75 2.875 5.50 8.5 12.5 10 22.5 1.06 26 49.6 67.50 1.1 5 6.5 30.75 45.26 42.2
5013S 5350 1.000 0.500 5.5 7.75 3.875 7.50 8.5 12.5 10 22.5 1.06 26 49.6 69.50 1.1 5 6.5 30.75 45.26 42.2
5013LS 5350 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 22.5 1.06 26 49.6 67.50 1.1 5 6.5 30.75 45.26 42.2
1 Shaft tolerance is +0.000 inch -0.001 inch
2 “V” represents length of straight extension of shaft
3 Tolerance on “D” dimensions will be +0.000 inches -0.060 inch
4 Dimension to AA hole

Conduit Box Dimensions

Motors are depicted with representative conduit box. For specific dimensions or a
complete motor outline drawing contact your authorized GE outlet.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Standard Features

6.1

HP Range 5-300

Vertical Hollow Shaft WPI

Poles 2,4,6
Voltage 230/460, 460
Efficiency EPAct
Frequency 60 Hz (De-rated at 50 Hz and noted on the nameplate.)
NEMA Design A or B
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.15 in/sec max
Bearing Caps Yes
Bearing Protection Shaft Slinger
Bearing Type High Thrust
Conduit Box Cast Iron
Coupling Non-Reverse or Bolted
End Shield Cast Iron
Fasteners SAE
Frame Material Cast Iron
Frame Size 213-449
Grease/Oil All Guide and 213-286 Thrust Bearings: Shell Alvania R3, 324-445 Thrust Bearings: ISO 32, 150 SUS
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System Non-Hygroscopic, Anti-Fungus, Meets NEMA MG1-31 for variable frequency drives.
Lifting Means Yes
Mounting Vertical P-Base
Nameplate Stainless Steel
Paint Gray, Polyurethane
Relubrication Yes
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80ºC @ 1.0 SF
Tests NEMA Routine, IEEE 112
Time Rating Continuous
Top Hat Steel
Warranty 12 months from date of purchase or 18 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Pricing

Volts: 230/460, 460

HP: 5 - 300
* Motor coupling is required and priced separately on page 6.5.

FLA @ NEMA Thrust Nom List Price Norm Wt CD Dim AG Dim

HP RPM Volts Frame 460 Code Down LRA Eff Cat No. Price Symbol Stk (lbs) (in) (in) Notes
5 3600 230/460 L213TP10 6.5 H 1900 44 85.5 V3109 $1,008 G5-7VHSB Y 220 20.25 24.29
6.2 5 1800 230/460 L213TP10 67 G 2400 38 87.5 V3116 $998 G5-7VHSB Y 220 20.25 24.29
7.5 3600 230/460 L213TP10 9.5 G 1900 61 87.5 V3108 $1,086 G5-7VHSB Y 220 20.25 24.29
7.5 1800 230/460 L213TP10 9.7 G 2400 59 88.5 V3115 $1,030 G5-7VHSB Y 220 20.25 24.29
Vertical Hollow Shaft WPI

10 3600 230/460 L213TP10 13.0 H 1900 89 88.5 V3107 $1,174 G5-7VHSB Y 220 20.25 24.29
10 1800 230/460 L215TP10 13.0 G 2350 76 89.5 V3141 $1,174 G5-7VHSB Y 220 20.25 24.29
10 1200 230/460 L256TP10 13.5 G 3750 80 90.2 V3177 $1,770 G5-7VHSB Y 370 23.38 27.85
10 1200 230/460 L256TP12 13.5 G 3750 80 90.2 V3178 $1,770 G5-7VHSB Y 370 23.38 27.85
15 3600 230/460 L215TP10 19.0 H 1850 125 89.5 V3139 $1,380 G5-7VHSB Y 220 20.25 24.29
15 1800 230/460 L254TP10 19.5 G 3250 117 91.0 V3158 $1,419 G5-7VHSB Y 340 23.38 30.60
15 1200 230/460 L284TP12 19.0 G 3700 116 90.2 V3191 $1,934 G5-7VHSB Y 507 24.75 29.25
20 3600 230/460 L254TP10 24.0 G 2600 151 90.2 V3157 $1,515 G5-7VHSB Y 340 23.38 27.85
20 1800 230/460 L256TP10 26.0 G 3250 157 91.0 V3173 $1,633 G5-7VHSB Y 370 23.38 27.85
20 1800 230/460 L256TP12 26.0 G 3250 157 91.0 V3174 $1,633 G5-7VHSB Y 370 23.38 27.85
25 3600 230/460 L256TP10 29.0 H 2600 205 91.0 V3170 $1,734 G5-7VHSB Y 370 23.38 27.85
25 3600 230/460 L256TP12 29.0 H 2600 205 91.0 V3171 $1,734 G5-7VHSB Y 370 23.38 27.85
25 1800 230/460 L284TP12 32.5 F 3200 156 91.7 V3189 $1,832 G5-7VHSB Y 507 24.75 29.25
25 1800 230/460 L284TP16 32.5 F 3200 156 91.7 V3190 $1,832 G5-7VHSB Y 507 24.75 29.25
30 3600 230/460 L284TP12 35.5 G 2600 228 91.0 V3188 $1,770 G5-7VHSB Y 507 24.75 29.25
30 1800 230/460 L286TP12 36.5 G 3150 222 92.4 V3198 $2,074 G5-7VHSB Y 507 24.75 29.25
30 1800 230/460 L286TP16 36.5 G 3150 222 92.4 V3199 $2,074 G5-7VHSB Y 507 24.75 29.25
30 1200 230/460 L326TP16 38.0 G 6550 215 92.4 V3423 $2,785 G5-7VHSB Y 855 28.22 32.53
40 3600 230/460 L286TP12 47.5 G 2500 290 91.7 V3197 $2,350 G5-7VHSB Y 507 24.75 29.45
40 1800 230/460 L324TP12 48.5 G 5700 282 93.0 V3411 $2,180 G5-7VHSB Y 760 28.22 32.53
40 1800 230/460 L324TP16 48.5 G 5700 282 93.0 V3409 $2,180 G5-7VHSB Y 760 28.22 32.53
40 1800 460 PWS L324TP16 48.5 G 5700 282 93.0 V3410 $2,180 G5-7VHSB Y 760 28.22 32.53
40 1200 230/460 L364TP16 50.0 G 9450 300 93.0 V3435 $3,488 G5-7VHSB Y 1102 31.16 35.70
50 3600 230/460 L324TP12 59.5 H 4550 405 92.4 V3407 $2,725 G5-7VHSB Y 790 28.22 32.53
50 3600 230/460 L324TP16 59.5 H 4550 405 92.4 V3450 $2,725 G5-7VHSB Y 760 28.22 32.53
50 1800 230/460 L326TP12 61.0 G 5650 360 93.0 V3422 $2,857 G5-7VHSB Y 760 28.22 32.53
50 1800 230/460 L326TP16 61.0 G 5650 360 93.0 V3420 $2,857 G5-7VHSB Y 760 28.22 32.53
50 1800 460 PWS L326TP16 61.0 G 5650 360 93.0 V3421 $2,857 G5-7VHSB Y 760 28.22 32.53
60 3600 460 PWS L326TP16 75.0 H 4500 530 92.4 V3551 $3,179 G5-7VHSB Y 760 28.22 32.53
60 1800 230/460 L364TP12 76.0 G 8200 450 93.6 V3552 $3,444 G5-7VHSB Y 1102 31.16 35.70
60 1800 460 PWS L364TP12 76.0 G 8200 450 93.6 V3431 $3,444 G5-7VHSB Y 1102 31.16 35.70
60 1800 230/460 L364TP16 76.0 G 8200 450 93.6 V3429 $3,444 G5-7VHSB Y 1102 31.16 35.70
60 1800 460 PWS L364TP16 76.0 G 8200 450 93.6 V3430 $3,444 G5-7VHSB Y 1102 31.16 35.70
60 1200 460 PWS L404TP16 74.5 G 13850 443 93.6 V3553 $4,791 G5-7VHSB Y 1590 36.94 41.96
PWS following the voltage denotes motor is Part Winding Start

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Pricing cont.

Volts: 230/460, 460

HP: 5 - 300
* Motor coupling is required and priced separately on page 6.5.

FLA @ NEMA Thrust Nom List Price Norm Wt CD Dim AG Dim

HP RPM Volts Frame 460 Code Down LRA Eff Cat No. Price Symbol Stk (lbs) (in) (in) Notes
75 3600 460 PWS L364TP16 90.0 H 6500 645 93.0 V3428 $3,995 G5-7VHSB Y 1102 31.16 35.70
75 1800 230/460 L365TP12 93.0 G 8100 563 94.1 V3554 $4,050 G5-7VHSB Y 1102 31.16 35.70 6.3
75 1800 460 PWS L365TP12 93.0 G 8100 563 94.1 V3442 $4,050 G5-7VHSB Y 1102 31.16 35.70
75 1800 230/460 L365TP16 93.0 G 8100 563 94.1 V3440 $4,050 G5-7VHSB Y 1102 31.16 35.70

Vertical Hollow Shaft WPI

75 1800 460 PWS L365TP16 93.0 G 8100 563 94.1 V3441 $4,050 G5-7VHSB Y 1102 31.16 35.70
75 1200 460 PWS L405TP16 93.0 G 13750 570 93.6 V3555 $5,733 G5-7VHSB Y 1590 36.94 41.96
100 1800 230/460 L404TP16 128.0 G 11900 560 94.1 V3451 $5,325 G5-7VHSB Y 1590 36.94 41.96
100 1800 460 PWS L404TP16 128.0 G 11900 560 94.1 V3453 $5,325 G5-7VHSB Y 1590 36.94 41.96
100 1200 230/460 L444TP16 123.0 G 13600 735 94.1 V3556 $7,806 G5-7VHSB Y 2075 44.78 50.11
100 1200 460 PWS L444TP16 123.0 G 13600 735 94.1 V3468 $7,806 G5-7VHSB Y 2075 44.78 50.11
125 1800 460 PWS L405TP16 162.0 G 11700 930 94.5 V3456 $5,929 G5-7VHSB Y 1590 36.94 41.96
150 1800 460 PWS L444TP16 173.0 G 11700 1065 95.0 V3464 $7,360 G5-7VHSB Y 2075 44.78 50.11
150 1800 460 PWS L444TP20 173.0 G 11700 1065 95.0 V3466 $7,360 G5-7VHSB Y 2075 44.78 50.11
200 1800 460 PWS L445TP16 232.0 G 11500 1495 95.0 V3470 $9,962 G5-7VHSB Y 2260 44.78 50.11
200 1800 460 PWS L445TP20 232.0 G 11500 1495 95.0 V3483 $9,962 G5-7VHSB Y 2260 44.78 50.11
250 1800 460 PWS L447TP20 297.0 G 14100 2050 95.4 V3278 $12,006 G5-7VHSB Y 3000 44.78 50.00
300 1800 460 PWS L449TP20 362.0 G 13800 2760 95.4 V3279 $14,299 G5-7VHSB Y 3500 49.78 55.00
PWS following the voltage denotes motor is Part Winding Start

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Dimensions

6.4

Motor Dimensions (All dimensions in inches)

Vertical Hollow Shaft WPI

Frame Size AG AJ AK BB BC BD BE BF BV CD ED QA QC QN
L213TP10/L215TP10 24.29 9.13 8.25 0.22 0.25 10.00 0.75 0.44 8.14 20.25 4.01 14.17 1.125 1.000
L213TP12/L215TP12 24.29 9.13 8.25 0.22 0.12 12.00 0.75 0.44 8.14 20.25 4.01 14.17 1.375 1.250
L254TP10/L256TP10 27.85 9.13 8.25 0.22 0.12 10.00 0.98 0.44 9.41 23.38 4.50 17.72 1.375 1.250
L254TP12/L256TP12 27.85 9.13 8.25 0.22 0.12 12.00 0.98 0.44 9.41 23.38 4.50 17.72 1.375 1.250
L254TP16/L256TP16 27.85 14.75 13.50 0.22 0.12 16.00 0.98 0.44 9.41 23.38 4.50 17.72 1.375 1.250
L284TP10/L286TP10 29.25 9.13 8.25 0.22 0.31 10.00 0.98 0.44 10.19 24.75 4.50 20.71 1.375 1.250
L284TP12/L286TP12 29.25 9.13 8.25 0.22 0.31 12.00 0.98 0.44 10.19 24.75 4.50 20.71 1.375 1.250
L284TP16/L286TP16 29.25 9.13 13.50 0.22 0.31 16.50 0.98 0.69 10.19 24.75 4.50 20.71 1.375 1.250
L324TP12/L326TP12 32.53 9.13 8.25 0.28 0.25 12.00 0.98 0.44 13.44 28.22 4.21 22.36 1.875 1.750
L324TP16/L326TP16 32.53 14.75 13.50 0.28 0.25 16.50 0.98 0.69 13.40 28.22 4.21 22.36 1.875 1.750
L364TP12/L365TP12 35.70 9.13 8.25 0.28 0.25 12.00 0.98 0.44 16.12 31.16 4.52 24.80 1.875 1.750
L364TP16/L365TP16 35.70 14.75 13.50 0.28 0.25 16.50 0.98 0.69 16.12 31.16 4.52 24.80 1.875 1.750
L404TP16/L405TP16 41.96 14.75 13.50 0.28 0.25 16.50 0.98 0.69 15.68 36.94 5.00 27.87 2.000 1.938
L404TP20/L405TP20 41.96 14.75 13.50 0.28 0.25 20.00 0.98 0.69 15.68 36.94 5.00 27.87 2.000 1.938
L444TP16/L445TP16 50.11 14.75 13.50 0.28 0.28 16.50 1.16 0.69 21.83 44.78 5.00 31.40 2.000 1.938
L444TP20/L445TP20 50.11 14.75 13.50 0.28 0.28 20.50 1.16 0.69 21.83 44.78 5.00 31.40 2.000 1.938
L444TP24/L445TP24 50.11 14.75 13.50 0.28 0.28 24.00 1.16 0.69 21.83 44.78 5.00 31.40 2.000 1.938
L447TP20 50.00 14.75 13.50 0.28 0.28 20.00 1.16 0.69 27.80 44.78 5.14 31.40 2.625 2.501
L449TP20 55.00 14.75 13.50 0.28 0.28 20.00 1.16 0.69 27.80 49.75 5.14 31.40 2.625 2.501

Conduit Box Dimensions (All dimensions in inches)

Frame Size AA AB AC XL XN
L213TP10/L215TP10 1.00 9.30 7.20 6.80 2.60
L254TP10/L256TP10 1.50 10.97 8.46 7.76 5.67
L254TP12/L256TP12 1.50 10.97 8.46 7.76 5.67
L284TP12/L286TP12 1.50 14.60 10.83 9.20 8.11
L284TP16/L286TP16 1.50 14.60 10.83 9.20 8.11
L324TP12/L326TP12 1.50 14.68 11.85 8.38 8.11
L324TP16/L326TP16 1.50 14.68 11.85 8.38 8.11
L364TP12/L365TP12 2.50 15.78 12.91 8.38 8.11
L364TP16/L365TP16 2.50 15.78 12.91 8.38 8.11
L404TP16/L405TP16 2.50 20.90 16.06 15.75 10.55
L444TP16/L445TP16 2.50 21.65 16.81 16.62 11.26
L444TP20/L445TP20 2.50 21.65 16.81 16.62 11.26
L447TP20 3.50 21.65 16.81 16.62 11.26
L449TP20 3.50 21.65 16.81 16.62 11.26
Weights and dimensions are for estimating only.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Kits and Accessories
Coupling Specify size of coupling with order
Frame Cat. Price Norm Dimensions in inches
Price
Size No. Symbol Stk BX Depth EW XG BY BZ XM XR
Y8250 $112 G5-7KITS Y 0.751 0.109 0.188
Y8251 $112 G5-7KITS Y 0.876 0.109 0.188 10-32
1.75 1.375 0.39 1.65
210TP Y8253 $112 G5-7KITS Y 0.938 0.140 0.250 UNF
Y8254 $112 G5-7KITS Y 1.001 0.140 0.250
Y8313 $112 G5-7KITS Y Blank coupling must be machined to proper dimensions
Y8255 $117 G5-7KITS Y 0.751 0.109 0.188 6.5
10-32
Y8256 $117 G5-7KITS Y 0.876 0.109 0.188 UNF
Y8257 $117 G5-7KITS Y 1.001 0.140 0.250 1.75 1.375 0.39 1.65
250TP

Vertical Hollow Shaft WPI

Y8258 $117 G5-7KITS Y 1.188 0.140 0.250 1/4 -20
Y8259 $117 G5-7KITS Y 1.251 0.104 0.250 UNC
Y8314 $117 G5-7KITS Y Blank coupling must be machined to proper dimensions
Y8260 $120 G5-7KITS Y 0.751 0.109 0.188
10-32
Y8261 $120 G5-7KITS Y 0.876 0.109 0.188 UNF
Y8262 $120 G5-7KITS Y 1.001 0.140 0.250 1.75 1.375 0.39 1.85
280TP
Y8263 $120 G5-7KITS Y 1.188 0.140 0.250 1/4 -20
Y8264 $120 G5-7KITS Y 1.251 0.140 0.250 UNC
Y8315 $120 G5-7KITS Y Blank coupling must be machined to proper dimensions
10-32
Y8320 $488 G5-7KITS Y 1.001 0.140 0.250 1.375
UNF
Y8321 $488 G5-7KITS Y 1.188 0.140 0.250
320TP Y8322 $488 G5-7KITS Y 1.251 0.140 0.250 N/A 1.750 0.47 1.46
1/4 -20
360TP Y8323 $488 G5-7KITS Y 1.251 0.140 0.375
UNC
Y8324 $488 G5-7KITS Y 1.438 0.140 0.375
2.120
Y8325 $488 G5-7KITS Y 1.501 0.140 0.375
Y8326 $488 G5-7KITS Y Blank coupling must be machined to proper dimensions
Y8327 $563 G5-7KITS Y 1.188 0.140 0.250
1.750
Y8328 $563 G5-7KITS Y 1.251 0.140 0.375
Y8329 $563 G5-7KITS Y 1.438 0.140 0.375 1/4 -20
N/A 0.62 2.52
400TP Y8330 $563 G5-7KITS Y 1.501 0.140 0.375 UNC 2.120
Y8331 $563 G5-7KITS Y 1.688 0.203 0.375
2.500
Y8332 $563 G5-7KITS N 1.751 0.203 0.375
Y8333 $563 G5-7KITS Y Blank coupling must be machined to proper dimensions
Y8334 $600 G5-7KITS N 1.188 0.140 0.250
1.750
Y8335 $600 G5-7KITS Y 1.251 0.140 0.375
Y8336 $600 G5-7KITS N 1.438 0.140 0.375
1/4 -20 2.120
Y8337 $600 G5-7KITS Y 1.501 0.140 0.375 N/A UNC
0.62 2.31
440TP
Y8338 $600 G5-7KITS Y 1.688 0.203 0.375
Y8339 $600 G5-7KITS Y 1.751 0.203 0.375 2.500
Y8340 $600 G5-7KITS N 1.938 0.203 0.375
Y8341 $600 G5-7KITS Y Blank coupling must be machined to proper dimensions
Y8362 $750 G5-7KITS Y 1.438 0.375
0.168 2.125
Y8363 $750 G5-7KITS Y 1.501 0.375
1/4-20 0.547
Y8364 $750 G5-7KITS Y 1.688 0.375
0.171 UNC
Y8365 $750 G5-7KITS N 1.751 0.375 2.500
Y8366 $750 G5-7KITS Y 1.938 0.500
0.222
Y8367 $750 G5-7KITS Y 2.001 0.500
447TP Y8368 $750 G5-7KITS Y 2.063 0.500 N/A 2.22
0.224
449TP Y8369 $750 G5-7KITS N 2.126 0.500 0.673
Y8370 $750 G5-7KITS Y 2.188 0.500 3/8-16
0.226 3.250
Y8371 $750 G5-7KITS Y 2.251 0.500 UNC
Y8372 $750 G5-7KITS Y 2.376 0.275 0.500
Y8373 $750 G5-7KITS Y 2.438 0.625
0.277 0.797
Y8374 $750 G5-7KITS Y 2.501 0.625
Y8375 $750 G5-7KITS Y Blank coupling must be machined to proper dimensions

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Vertical
Value Line™ Vertical Hollow Shaft
Weather Protection I
Ball Style Non-Reverse Ratchet
Kits and Accessories cont.

Optional Stabilizer/Steady Bushing

Frame Price Dim. in inches

Size Cat. No. List Price Symbol A BX Norm Stk
Y8284 $73 G5-7KITS 1.76 1.000 Y
210TP/ Y8285 $73 G5-7KITS 1.76 0.937 Y
250TP Y8286 $73 G5-7KITS 1.76 0.875 Y
6.6 Y8287 $73 G5-7KITS 1.76 0.750 Y
Y8288 $73 G5-7KITS 1.76 1.250 Y
250TP
Y8289 $73 G5-7KITS 1.76 1.187 Y
Y8290 $71 G5-7KITS 2.17 1.250 Y
Vertical Hollow Shaft WPI

Y8291 $71 G5-7KITS 2.17 1.187 Y

280TP Y8292 $71 G5-7KITS 2.17 1.000 Y
Y8293 $71 G5-7KITS 2.17 0.875 Y
Y8294 $71 G5-7KITS 2.17 0.75 Y
Y8295 $90 G5-7KITS 2.36 1.500 Y
Y8296 $90 G5-7KITS 2.36 1.437 Y
Y8297 $90 G5-7KITS 2.36 1.250 Y
320TP
Y8298 $90 G5-7KITS 2.36 1.187 Y
Y8299 $90 G5-7KITS 2.36 1.126 Y
Y8301 $90 G5-7KITS 2.36 1.000 Y
Y8302 $90 G5-7KITS 2.56 1.500 N
Y8303 $90 G5-7KITS 2.56 1.437 Y
Y8304 $90 G5-7KITS 2.56 1.250 Y
360TP
Y8305 $90 G5-7KITS 2.56 1.187 Y
Y8306 $90 G5-7KITS 2.56 1.126 Y
Y8307 $90 G5-7KITS 2.56 1.000 Y
Y8308 $94 G5-7KITS 2.64 1.750 Y
Y8309 $94 G5-7KITS 2.64 1.687 Y
Y8310 $94 G5-7KITS 2.64 1.500 Y
400TP/
Y8311 $94 G5-7KITS 2.64 1.437 Y
440TP
Y8312 $94 G5-7KITS 2.64 1.250 Y
Y8360 $94 G5-7KITS 2.64 1.187 Y
Y8361 $94 G5-7KITS 2.64 1.000 Y
Y8383 $157 G5-7KITS 3.43 1.438 Y
Y8384 $157 G5-7KITS 3.43 1.501 Y
Y8385 $157 G5-7KITS 3.43 1.688 Y
Y8386 $157 G5-7KITS 3.43 1.751 N
Y8387 $157 G5-7KITS 3.43 1.938 Y
Y8388 $157 G5-7KITS 3.43 2.001 Y
447TP/
Y8389 $157 G5-7KITS 3.43 2.063 Y
449TP
Y8390 $157 G5-7KITS 3.43 2.126 N
Y8391 $157 G5-7KITS 3.43 2.188 Y
Y8392 $157 G5-7KITS 3.43 2.251 Y
Y8393 $157 G5-7KITS 3.43 2.376 Y
Y8394 $157 G5-7KITS 3.43 2.438 Y
Y8395 $157 G5-7KITS 3.43 2.501 Y

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Vertical
Solid Shaft Inline Pump
Standard Features

HP Range 3-40
6.7
Poles 2, 4
Voltage 230/460
Efficiency EPAct
Frequency 60 Hz (De-rated at 50 Hz and noted on the nameplate.)

Vertical Inlilne
NEMA Design A or B
Frame Size L182LP10-L324LP16
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors
Altitude 3300 ft
Ambient 40ºC
Balance/Vibration 0.15 in/sec max
Bearing Caps Yes
Bearing Protection Shaft Slinger
Bearing Type Guide Bearing: Deep Groove Ball Bearing; Thrust Bearing: Double Row Angular Contact Ball Bearing
Conduit Box Cast Iron
Coupling Non-Reverse or Bolted
End Shield Cast Iron
Fasteners SAE
Frame Material Cast Iron
Grease/Oil All Guide and 213-286 Thrust Bearings: Polyurea, 324-326 Thrust Bearings: Oil
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System Non-Hygroscopic, Anti-Fungus, Meets NEMA MG1-31 for variable frequency drives.
Inverter Capabilities INF:1 Variable torque
L10 Bearing Life 8760 hrs
Lifting Means Yes
Mounting Vertical P-Base
Mounting Holes Per NEMA
Nameplate Stainless Steel
Paint Gray Expoxyester
Relubrication Yes
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80ºC @ 1.0 SF
Tests NEMA Routine, IEEE 112
Time Rating Continuous
Top Hat Steel
Warranty 12 months from date of purchase, 18 months from date of shipment

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Vertical
Solid Shaft Inline Pump
Pricing

Three Phase - Totally Enclosed Fan Cooled - Severe Duty - Inline Pump
Volts: 230/460
HP: 3- 40
Down
Nom Catalog Multiplier Norm Thrust
HP RPM Volts NEMA Frame SF FLA @ NP Eff No List Price Symbol Stk WT (lbs) C Dim Notes
3 3600 230/460 L182LP10 1.15 7.8/3.9 87.5 V824 $1,029 G6-7VIL N 76 1014 18.18 CI
3 1800 230/460 L182LP10 1.15 7.8/3.9 89.5 V833 $1,029 G6-7VIL Y 76 1272 18.18 CI
5 3600 230/460 L184LP10 1.15 12.4/6.2 90.2 V825 $1,304 G6-7VIL Y 101 1014 18.18 CI
5 1800 230/460 L184LP10 1.15 12.8/6.4 89.5 V834 $1,118 G6-7VIL N 101 1272 18.18 CI
6.8
7.5 3600 230/460 L213LP10 1.15 17.2/8.6 90.2 V826 $1,453 G6-7VIL N 200 860 22.34 CI
7.5 1800 230/460 L213LP10 1.15 18.0/9.0 91.0 V835 $1,426 G6-7VIL Y 200 1075 22.34 CI
10 3600 230/460 L215LP10 1.15 22.4/11.2 91.0 V827 $1,604 G6-7VIL N 220 860 22.34 CI
10 1800 230/460 L215LP10 1.15 24.0/12.0 91.0 V836 $1,569 G6-7VIL Y 220 1075 22.34 CI
Vertical Inline

15 3600 230/460 L254LP10 1.15 34.6/17.3 91.7 V828 $1,814 G6-7VIL Y 315 1076 27.33 CI
15 1800 230/460 L254LP10 1.15 36.6/18.3 92.4 V837 $1,908 G6-7VIL N 315 1340 22.34 CI
20 3600 230/460 L256LP10 1.15 45.8/22.9 91.7 V829 $2,039 G6-7VIL Y 350 1076 27.33 CI
20 1800 230/460 L256LP10 1.15 48.0/24.0 92.4 V838 $2,123 G6-7VIL Y 350 1348 27.33 CI
25 3600 230/460 L284LP10 1.15 55.8/27.9 92.4 V830 $2,281 G6-7VIL Y 460 1316 31.66 CI
25 1800 230/460 L284LP10 1.15 58.2/29.1 93.6 V839 $2,418 G6-7VIL N 460 1639 31.66 CI
30 3600 230/460 L286LP10 1.15 67.2/33.6 92.4 V831 $2,460 G6-7VIL N 510 1316 31.66 CI
30 1800 230/460 L286LP10 1.15 69.0/34.5 93.6 V840 $2,662 G6-7VIL N 510 1639 31.66 CI
40 3600 230/460 L324LP16 1.15 98.8/49.4 93.0 V832 $4,710 G6-7VIL N 650 2329 41.07 CI, 92
40 1800 230/460 L324LP16 1.15 98.8/49.4 93.6 V841 $4,267 G6-7VIL Y 730 2883 41.07 CI, 92
Notes
CI Cast Iron
92 Oil lubrication both bearing

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Vertical
Solid Shaft Inline Pump
Dimensions

6.9

All Dimensions in Inches

Vertical Inline
High Thrust VP Shaft Inline LP Shaft AG
Frame U EU AH U EU AH WPI TEFC
L182/L184 1.125 0.875 2.75 1.125 0.875 2.75 14.69 15.67
L213/L215 1.125 0.875 2.75 1.625 1.250 2.75 16.55 23.60
L254/L256 1.125 0.875 2.75 1.625 1.250 2.75 20.93 28.25
L284/L286 1.125 0.875 2.74 2.125 1.750 4.50 23.00 30.50
L324/L326 1.625 1.250 4.50 2.125 1.750 4.50 36.93 36.99
L364/L365 1.625 1.250 4.50 2.125 1.750 4.50 40.28 40.88
L404/L405 1.625 1.250 4.50 2.125 1.750 4.50 45.30 46.56
L444/L445 2.125 1.750 4.50 2.125 1.750 4.50 42.86 53.40
L449 2.125 1.750 4.50 2.125 1.750 4.50 51.36 61.90
Notes
Inline motors are only available in TEFC construction.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

6.10

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW Fire Pump Motor
Standard Features

HP Range 5-200
Poles 2and 4
Voltage 230/460, 460 6.11
Efficiency EPAct through 200 HP
Frequency 60
NEMA Design B

Fire Pump Motor

Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft
Ambient 40C
Balance/Vibration 143-405: .150 in/sec max
Bearing Caps 284TS-286TS and 324-445
Bearing Type Ball, 143T-286T Shielded; 284TS-286TS and 324-445 Open
Conduit Box Stamped Steel, rotatable
End Shield Cast Iron
Fasteners Metric, ISO 8.8
Frame Material Cast Iron
Frame Size 184-445
Grease 143T-286T: Lithium, 284TS-286TS and 324-445: Polyuera
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System Non-Hygroscopic, Anti-Fungus, meets NEMA MG1-31
Inverter Capabilities N/A
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 25,000 hrs
Lifting Means 143-145: None, All others: Eye Bolt
Mounting F1
Mounting Holes 2 per foot
Nameplate Stainless Steel
Paint Gray, Polyurethane
Relubrication 284TS-286TS and 324-445
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80C @ 1.0SF
Tests NEMA Routine, IEE112B
Time Rating Continuous
Warranty 12 months from date of purchase or 18 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Fire Pump Motor NEW
Open Dripproof
Pricing
Volts: 230/460, 460
HP: 5-200
Cat Price Normally
HP RPM Volts Frame FLA Nom Eff No. List Price Symbol Stocked Wt (lbs) C Dim (in) Notes
5 3600 230/460 180T 12.0/6.2 85.5 S3616 $605 G4-7DEF Y 73 13.71 130
5 1800 230/460 184T 12.6/6.3 87.5 S3601 $585 G4-7DEF Y 104 13.53 124
7.5 3600 230/460 184T 17.4/8.7 87.5 S3617 $725 G4-7DEF Y 93 14.71 130
7.5 1800 230/460 213T 18.8/9.4 88.5 S3602 $719 G4-7DEF Y 128 15.85 124
10 3600 230/460 213T 24.4/12.2 88.5 S3618 $890 G4-7DEF Y 128 17.74 130
10 1800 230/460 215T 24.6/12.3 89.5 S3603 $855 G4-7DEF Y 180 17.38 124
6.12 15 3600 230/460 215T 35.6/17.8 89.5 S3619 $1,050 G4-7DEF Y 157 19.04 130
15 1800 230/460 254T 35.0/17.5 91.0 S3604 $1,045 G4-7DEF Y 260 20.67 124
20 3600 230/460 254T 45.4/22.7 90.2 S3620 $1,275 G4-7DEF Y 260 20.45 130
20 1800 230/460 256T 47.4/23.7 91.0 S3605 $1,271 G4-7DEF Y 310 22.40 124
Fire Pump Motor

25 3600 230/460 256T 56.4/28.2 91.0 S3621 $1,493 G4-7DEF Y 307 22.19 130
25 1800 230/460 284T 59.8/29.9 91.0 S3606 $1,491 G4-7DEF Y 394 23.82 124
30 3600 230/460 284T 68.7/34.3 91.0 S3622 $1,660 G4-7DEF Y 378 23.43 130
30 1800 230/460 286T 70.6/35.3 92.4 S3607 $1,655 G4-7DEF Y 436 25.32 124
40 3600 230/460 286T 90.5/45.2 91.7 S3623 $1,950 G4-7DEF Y 406 24.93 130
40 1800 230/460 324T 92.6/46.3 93.0 S3608 $1,925 G4-7DEF Y 575 26.26 124
50 3600 230/460 324T 113.2/56.6 92.4 S3624 $2,685 G4-7DEF Y 595 26.05 130
50 1800 230/460 326T 115.6/57.8 93.0 S3609 $2,232 G4-7DEF Y 575 27.76 124
60 3600 230/460 326T 135.8/67.9 93.0 S3625 $2,985 G4-7DEF Y 661 27.54 130
60 1800 230/460 364TS 140.4/70.2 93.6 S3610 $2,771 G4-7DEF Y 730 27.00 124
75 3600 230/460 364TS 165.8/82.9 93.0 S3626 $3,297 G4-7DEF Y 674 27.00 130
75 1800 230/460 365TS 173.4/86.7 94.1 S3611 $3,345 G4-7DEF Y 838 28.00 124
100 3600 230/460 365TS 220.1/110.0 93.0 S3627 $4,260 G4-7DEF Y 763 28.00 130
100 1800 230/460 404TS 228.0/114.0 94.1 S3612 $4,275 G4-7DEF Y 1045 30.10 124
125 3600 230/460 404TS 283.0/141.7 93.6 S3628 $5,048 G4-7DEF Y 1031 30.10 130
125 1800 230/460 405TS 278.0/139.0 94.5 S3613 $5,101 G4-7DEF Y 1225 31.60 124
150 3600 460 405TS 168.5 93.6 S3629 $6,350 G4-7DEF Y 1124 31.60 131
150 1800 460 444TS 167.0 95.0 S3614 $6,705 G4-7DEF Y 1430 33.95 125
200 3600 460 444TS 219.3 94.5 S3630 $9,350 G4-7DEF Y 1510 33.95 131
200 1800 460 445TS 220.0 95.0 S3615 $8,789 G4-7DEF Y 1610 35.95 125

Notes
124 Usable on 190/380V, 50Hz, same HP at 1.0 service factor
125 Usable on 380V, 50Hz, same HP at 1.0 service factor
130 Usable on 190/380V, 50Hz, next lower HP at 1.15 service factor
131 Usable on 380V, 50Hz, next lower HP at 1.15 service factor

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 NEW Fire Pump Motor
Open Dripproof
Dimensions

N MIN

V
KEY LENGTH

D 6.13

2E H HOLE 2F BA

Fire Pump Motor

NEMA Frame D 2E 2F BA H N Min. U V Min. Key Width Key Thickness Key Length
184T 4.50 7.50 5.50 2.75 0.41 Dia. 2.75 1.12 2.50 0.25 0.25 1.75
213T 5.25 8.50 5.50 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
215T 5.25 8.50 7.00 3.50 0.41 Dia. 3.38 1.38 3.12 0.31 0.31 2.38
254T 6.25 10.00 8.25 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
256T 6.25 10.00 10.00 4.25 0.53 Dia. 4.00 1.62 3.75 0.38 0.38 2.88
284T 7.00 11.00 9.50 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
286T 7.00 11.00 11.00 4.75 0.53 Dia. 4.62 1.88 4.38 0.50 0.50 3.25
324T 8.00 12.50 10.50 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
326T 8.00 12.50 12.00 5.25 0.66 Dia. 5.25 2.12 5.00 0.50 0.50 3.88
364TS 9.00 14.00 11.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
365TS 9.00 14.00 12.25 5.88 0.69 Dia. 3.75 1.88 3.50 0.50 0.50 2.00
404TS 10.00 16.00 12.25 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
405TS 10.00 16.00 13.75 6.62 0.81 Dia. 4.25 2.12 4.00 0.50 0.50 2.75
444TS 11.00 18.00 14.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00
445TS 11.00 18.00 16.50 7.50 0.81 Dia. 4.75 2.38 4.50 0.62 0.62 3.00

NOTE
“C” Dimension is overall length and is shown for each catalog number on rating pages. All dimensions in inches.
All dimensions are nominal. Request factory outlines for exact dimensions.

1. Motor base has two sets of holes at 3.00 and 5.00 inches.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

6.14

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 High Speed Pump Motor
CE Mark
(IP54 Enclosure)
Standard Features

HP Range 3-150
Poles 2
Voltage 230/460, 460
Efficiency EPAct through 200 HP
Frequency 60
NEMA Design A or B 6.15
Agency Approvals UL - Component and Insulation System Recognition, CSA - Motors and C-390
Altitude 3300 ft

High Speed Pump Motor

Ambient 40C
Balance/Vibration 143-405: .150 in/sec max
Bearing Caps 284TS-286TS and 324-445
Bearing Protection Shaft Slinger
Bearing Type Ball, 143T-286T Shielded; 284TS-286TS and 324-445 Open
Conduit Box Cast Iron, rotatable
End Shield Cast Iron
Fasteners Metric, ISO 8.8
Frame Material Cast Iron
Frame Size 182-445
Grease 143T-256T: Multemp SRL (Lithium base), 284-286 and 324-445: Polyurea
Ground Brass Bolt in Conduit Box
Insulation Class F
Insulation System Non-Hygroscopic, Anti-Fungus, meets NEMA MG1-31
Inverter Capabilities Variable Torque Loads
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 25,000 hrs
Lifting Means 143-145: None, All others: Eye Bolt
Mounting F1
Mounting Holes 1 per foot
Nameplate Stainless Steel
Paint (Blue RAL 5019) Capriblau
Relubrication 284TS-286TS and 324-445
Rotor Cast Aluminum
Service Factor 1.15
Temperature Rise 80C @ 1.0SF
Tests NEMA Routine, IEE112B
Thermal Protection 254T frame and larger have qty 2 - NC Class B thermostats
Time Rating Continuous
Warranty 12 months from date of purchase or 18 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 High Speed Pump Motor
CE Mark
(IP54 Enclosure)
Pricing

Volts: 230/460, 460

HP: 3- 150
Nom List Price Normally Wt C Dim
HP RPM Volts Frame FLA Cat No. Eff Price Symbol Stocked (lbs) (in) Notes
3 3600 230/460 182TCY 7.2/3.6 S2948 85.5 $481 G4-7TEZ Y 98 14.40 109, 110
5 3600 230/460 184TCY 11.8/5.9 S2949 87.5 $595 G4-7TEZ Y 106 15.40 109, 110
7.5 3600 230/460 213TCY 17.8/8.9 S2950 88.5 $743 G4-7TEZ Y 156 17.78 109, 110
10 3600 230/460 215TCY 23.2/11.6 S2951 89.5 $878 G4-7TEZ Y 183 19.28 109, 110
6.16 15 3600 230/460 254TCY 33.6/16.8 S2952 90.2 $1,132 G4-7TEZ Y 282 23.43 109, 110, 127
20 3600 230/460 256TCY 44.4/22.2 S2953 90.2 $1,473 G4-7TEZ Y 315 25.20 109, 110, 127
25 3600 230/460 284TSC 55.6/27.8 S2954 91.0 $2,114 G4-7TEZ Y 418 25.15 109, 127
High Speed Pump Motor

30 3600 230/460 286TSC 66.8/33.4 S2955 91.0 $2,257 G4-7TEZ Y 455 28.02 109, 127
40 3600 230/460 324TSC 89.2/44.6 S2941 91.7 $2,632 G4-7TEZ Y 802 30.32 109, 127
50 3600 230/460 326TSC 109.4/54.4 S2942 92.4 $3,059 G4-7TEZ Y 835 30.32 109, 127
60 3600 230/460 364TSC 133.4/66.7 S2943 93.0 $4,608 G4-7TEZ Y 955 32.68 109, 127
75 3600 230/460 365TSC 166.6/83.3 S2944 93.0 $5,511 G4-7TEZ Y 1012 32.68 109, 127
100 3600 230/460 404TSC 222/111 S2945 93.6 $7,128 G4-7TEZ Y 1259 35.63 109, 127
125 3600 460 405TSC 136.0 S2946 94.5 $9,327 G4-7TEZ Y 1623 41.75 126, 127
150 3600 460 444TSC 164.0 S2947 94.5 $12,063 G4-7TEZ Y 1722 41.75 126, 127
Notes
109 Usable on 200/400V, 50 Hz at 1.15SF and de-rated to next lower HP
110 Non-NEMA BA dimension
126 Usable on 400V, 50 Hz at 1.15SF and de-rated to next lower HP
127 Quantity 2 - N.C. Class B Thermostat

Kits and Accessories

Terminal Board Kits (available for all frame sizes)

Main motor leads are connected to the terminal board inside the main conduit box.

Price
Frame Part No. Cat No. List Price Symbol Norm Stk
182TC/184TC 227B1056AA-G01 A320 Contact Factory for price and availability
213TC/215TC * 227B1058AA-G02 A321 Contact Factory for price and availability
254TC/256TC ** 227B1058AA-G01 A322 Contact Factory for price and availability
284TSC/286TSC 227B1056AB-G01 A323 Contact Factory for price and availability
324TSC/326TSC 227B1056AC-G01 A324 Contact Factory for price and availability
364TSC/365TSC 227B1056AD-G01 A325 Contact Factory for price and availability
405TSC 227B1056AD-G02 A326 Contact Factory for price and availability
444TSC/445TSC 227B1056AD-G03 A327 Contact Factory for price and availability
* Kit includes Oversize Conduit Box
** Kit includes additional terminal board for thermostat leads

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 High Speed Pump Motor
CE Mark
(IP54 Enclosure)
Dimensions

AH
KEY

BF HOLE
1/4" MIN

45 ?

BD 6.17
AK AJ
D

High Speed Pump Motor

U

E E

2F BA N-W

Approx. Key
Nema Vol.
Frame HP (cubic in) Width Depth Length D E 2F BA H AH U N-W C BD AK AJ BF
182TCY 3 26 0.250 0.250 1.780 4.50 3.75 4.50 2.75 0.41 2.62 1.125 2.75 14.40 9.00 8.50 7.25 1/2-13 tap
184TCY 5 26 0.250 0.250 1.780 4.50 3.75 5.50 2.75 0.41 2.62 1.125 2.75 15.40 9.00 8.50 7.25 1/2-13 tap
213TCY 7.5 63 0.312 0.312 2.410 5.25 4.25 5.50 3.50 0.41 2.87 1.375 3.38 17.78 9.00 8.50 7.25 1/2-13 tap
215TCY 10 63 0.312 0.312 2.410 5.25 4.25 7.00 3.50 0.41 2.87 1.375 3.38 19.28 9.00 8.50 7.25 1/2-13 tap
254TCY 15 63 0.375 0.375 2.910 6.25 5.00 8.25 4.25 0.53 3.45 1.625 4.00 23.43 9.93 8.50 7.25 1/2-13 tap
256TCY 20 63 0.375 0.375 2.910 6.25 5.00 10.00 4.25 0.53 3.45 1.625 4.00 25.20 9.93 8.50 7.25 1/2-13 tap
284TSC 25 116 0.375 0.375 1.930 7.00 5.50 9.50 4.75 0.53 2.75 1.625 3.25 25.15 11.22 10.50 9.00 1/2-13 tap
286TSC 30 116 0.375 0.375 1.930 7.00 5.50 11.00 4.75 0.53 2.75 1.625 3.25 26.65 11.22 10.50 9.00 1/2-13 tap
324TSC 40 350 0.500 0.500 2.050 8.00 6.25 10.50 5.25 0.66 3.50 1.875 3.75 30.32 14.00 12.50 11.00 5/8-11 tap
326TSC 50 350 0.500 0.500 2.050 8.00 6.25 12.00 5.25 0.66 3.50 1.875 3.75 30.32 14.00 12.50 11.00 5/8-11 tap
364TSC 60 460 0.500 0.500 2.050 9.00 7.00 11.25 5.88 0.66 3.50 1.875 3.75 32.68 14.00 12.50 11.00 5/8-11 tap
365TSC 75 460 0.500 0.500 2.050 9.00 7.00 12.25 5.88 0.66 3.50 1.875 3.75 32.68 14.00 12.50 11.00 5/8-11 tap
405TSC 100 460 0.500 0.500 2.830 10.00 8.00 13.75 6.62 0.81 4.00 2.125 4.25 35.63 N/A 12.50 11.00 5/8-11 tap
444TSC 125 460 0.625 0.625 3.030 11.00 9.00 14.50 7.50 0.81 4.50 2.375 4.75 41.75 N/A 16.00 14.00 5/8-11 tap
445TSC 150 460 0.625 0.625 3.030 11.00 9.00 16.50 7.50 0.81 4.50 2.375 4.75 41.75 N/A 16.00 14.00 5/8-11 tap
NOTE
“C” Dimension is overall length and is shown for each catalog number on rating pages. All dimensions in inches.
All dimensions are nominal. Request factory outlines for exact dimensions.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

6.18

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Standard Features

Introduction
Designed to meet NEMA specifications, GE Industrial Systems complete line of DC motor offerings are available
to meet all of your DC motor needs. The Kinamatic line of motors featured in this publication is a result of many
years of research and development. Quality components and craftsmanship are designed to provide years of
dependable motor performance.

Frames
The rugged frame construction of Kinamatic motors is just one feature designed for optimum motor
performance in the most demanding industrial applications.

Bearings
Antifriction bearings permit mounting of standard CD320AT and below frame sizes at any angle and
CD365AT-CD508AT frames mounted vertical shaft down.

Insulation
Kinamatic DC motors have Class F insulation containing a number of components rated Class H, unless
otherwise specified.

The insulation system employs many proprietary materials and processes developed specifically for this line of
machines. The system was chosen to provide long life at rated loads and also to withstand the effects of
mechanical shock, vibration, and the contamination of many severe environments. The Class F insulation system
has been proven by laboratory tests and by many years of successful operation. 7.1

TIG Welding
Low maintenance, trouble free commutator riser joints are provided by TIG (Tungsten Inert Gas) welding

DC Motors – Kinamatic™
commutator risers to the armature coil.

The strong copper-to-copper connection eliminates the use of material with low melting temperatures and
greatly increases the motor's ability to withstand overloads.

Other benefits of TIG welding include excellent mechanical strength and overload capacity, no tin or lead
contaminants, and no throwing of solder. TIG welding is found on CD180AT and above frame sizes.

Motor Finish
Our standard motor or generator paint is a machine tool ANSI #49 grey, heavy duty acrylic enamel over a water
based primer. Polyurethane paint is available for waterproof motors.

Trec® Field Coils

Tape Reinforced Encapsulated Construction (TREC®) of all main field coils and commutating field coils is a process
which strengthens, seals, and bonds the coil to the pole to form a single unit that is highly resistant to
contamination, vibration, impact, and wear.

The TREC® coil is engineered to be elastic enough to withstand expansion and contraction due to temperature
differences. The TREC® coil is standard on frames CD365AT-CD5010AY and CD6000-CD6900.

Armature Treatment
Radiant Heat Process (RHP) – All armatures in frames CD180-500AT are treated with a solventless polyester
varnish, Radiant Heat Process. Armatures, in horizontal position, are rotated under radiant electric heaters. After
preheating, the armatures are dipped and rotated under heaters to cure the varnish. This process locks the resin
in place, filling the voids.

Vacuum pressure impregnation (VPI) – Armatures are given a vacuum pressure impregnation (VPI) treatment with
high temperature varnish. Armatures are placed into a vacuum vessel that pulls air from the armature. Resin is
then allowed into the vessel, and pressure is applied. The pressure pushes the resin into the void. The armature is
then drained and baked. Two VPI cycles ensure an even varnish coating and an excellent heat transfer path
while eliminating all air pockets.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™
Type-C Power Supply
Pricing

Base Mounted - GE CD180AT-CD500AT

Shunt Wound - Dripproof Fully Guarded - Self Ventilated
Armature Armature Price Norm C Dim
HP RPM Volts Field Volts Amps Field Amps Frame Cat No. List Price Symbol Stk Wt (lbs) (in) Notes
2 1750/2300 240 300/150 7.6 .35/.20 L182AT D587 $1,804 GO-2AS Y 83 15.30
3 1750/2300 240 300/150 11.0 .34/.23 186AT D403 $2,124 GO-2AS Y 105 16.80
3 1750/2300 500 300/150 5.1 .55/.30 186AT D588 $2,124 GO-2AS N 105 16.80
3 1750/2300 240 240/120 11.0 .44/.28 186ATC D404 $2,210 GO-2AS Y 102 16.80 75
5 1750/2300 240 300/150 18.0 .45/.27 L186AT D409 $2,612 GO-2AS Y 128 18.80
5 1750/2300 500 300/150 8.5 .72/.42 L186AT D407 $2,612 GO-2AS N 128 18.80
5 1750/2300 240 240/120 17.9 .57/.39 L186ATC D410 $2,698 GO-2AS N 128 18.80 75
7.5 1750/2300 240 300/150 26.5 .95/.52 189AT D417 $3,152 GO-2AS N 162 20.80
7.5 1750/2300 500 300/150 13.2 .78/.54 218AT D421 $3,152 GO-2AS Y 234 24.20
7.5 1750/2300 240 240/120 28.1 .98/.63 218ATC D422 $3,403 GO-2AS Y 243 24.20 75
10 1750/2300 240 300/150 36.6 1.12/.64 219AT D425 $3,592 GO-2AS Y 252 25.20
10 1750/2300 500 300/150 17.2 1.35/.88 219AT D423 $3,592 GO-2AS Y 252 25.20
10 1750/2300 240 240/120 36.6 1.40/.86 219ATC D427 $3,843 GO-2AS Y 252 25.20 75
15 1750/2300 240 300/150 56.0 1.30/.80 258AT D434 $4,321 GO-2AS Y 361 27.10
15 1750/2300 500 300/150 25.2 1.60/.88 258AT D432 $4,321 GO-2AS Y 361 27.10
15 1750/2300 240 240/120 55.1 1.67/.89 258ATC D435 $4,572 GO-2AS N 378 27.10 75
7.2 20 1750/2300 240 300/150 70.5 1.42/.95 259AT D441 $4,955 GO-2AS N 403 28.80
20 1750/2300 500 300/150 35.0 1.53/.83 259AT D437 $4,955 GO-2AS Y 403 28.80
25 1750/2300 240 300/150 91.0 1.47/.90 287AT D444 $6,118 GO-2AS Y 493 31.00
DC Motors – Kinamatic™

25 1750/2300 500 300/150 42.7 1.76/1.20 287AT D442 $6,118 GO-2AS Y 493 31.00
25 1150/2000 240 300/150 89.0 1.89/1.08 328AT D589 $7,950 GO-2AS N 769 35.40
30 1750/2300 240 300/150 107.0 1.56/1.11 288AT D448 $6,734 GO-2AS N 548 32.70
30 1750/2300 500 300/150 50.4 2.08/1.16 288AT D445 $6,734 GO-2AS Y 548 32.70
40 1750/2100 500 300/150 65.4 2.32/1.69 328AT D541 $7,922 GO-2AS N 769 35.40
40 1750/2100 500 300/150 65.4 2.32/1.69 328AT D542 $7,922 GO-2AS N 769 35.40 70
40 1150/2000 500 300/150 64.9 2.90/1.35 366AT D453 $10,542 GO-2AS N 860 35.90
50 1750/2100 500 300/150 83.7 2.32/1.70 328AT D449 $9,049 GO-2AS Y 769 35.40
50 1750/2100 500 300/150 83.7 2.32/1.70 328AT D450 $9,049 GO-2AS Y 769 35.40 70
50 1150/2000 500 300/150 80.0 2.50/1.32 368AT D543 $12,140 GO-2AS N 1020 38.90
60 1750/2100 500 300/150 97.4 3.00/2.30 366AT D544 $10,358 GO-2AS N 860 35.90
60 1150/2000 500 300/150 98.0 2.50/1.30 368AT D462 $13,872 GO-2AS N 1020 38.90
60 850/1700 500 300/150 99.0 3.00/1.30 407AT D590 $16,900 GO-2AS N 1300 40.10
75 1750/2100 500 300/150 122.0 3.06/2.30 366AT D455 $12,169 GO-2AS Y 860 35.90
75 1750/2100 500 300/150 122.0 3.06/2.30 366AT D456 $12,169 GO-2AS N 860 35.90 70
100 1750/2000 500 300/150 161.0 3.80/2.80 368AT D465 $15,266 GO-2AS N 1020 38.90
100 1750/2000 500 300/150 160.0 3.80/2.80 368AT D466 $15,266 GO-2AS N 1020 38.90 70
125 1750/2000 500 300/150 200.0 3.06/2.55 407AT D471 $18,079 GO-2AS Y 1300 40.10
150 1750/2000 500 300/150 238.0 3.80/3.30 409AT D476 $21,751 GO-2AS N 1600 44.60
150 1750/2000 500 300/150 238.0 3.80/3.30 409AT D477 $21,751 GO-2AS N 1600 44.60 70
200 1750/2000 500 300/150 319.0 4.00/3.25 504AT D480 $27,588 GO-2AS N 1900 45.70
250 1750/1900 500 300/150 394.0 8.00/6.68 506AT D547 $33,922 GO-2AS N 2290 49.70
300 1750/1900 500 300/150 473.0 8.00/6.83 506AT D486 $40,675 GO-2DS N 2290 49.70
Notes
70 F-2 assembly
75 C-Face Mounting

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™
Type-C Power Supply
Pricing cont.

Base Mounted - GE CD180AT-CD500AT

Shunt Wound - Dripproof Fully Guarded - Separately Ventilated
Armature Armature Price C Dim
HP RPM Volts Field Volts Amps Field Amps Frame Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
10 1750/2300 240 300/150 36.6 1.12/0.64 219AT D426 $3,592 GO-2AS N 252 25.20
10 1750/2300 500 300/150 17.2 1.35/0.88 219AT D424 $3,592 GO-2AS Y 252 25.20
15 1750/2300 500 300/150 25.2 1.60/0.88 258AT D433 $4,321 GO-2AS N 361 27.10
20 1750/2300 500 300/150 35.0 1.53/0.83 259AT D438 $4,955 GO-2AS N 403 28.80
20 1750/2300 500 300/150 35.0 1.53/0.83 259AT D439 $4,955 GO-2AS N 403 28.80 70
30 1750/2300 500 300/150 50.4 2.08/1.16 288AT D446 $6,136 GO-2AS N 548 32.70
40 1750/2100 500 300/150 67.0 2.03/1.32 327AT D548 $7,216 GO-2AS Y 691 33.40
40 1150/2000 500 300/150 70.2 2.30/1.01 328AT D609 $9,187 GO-2AS N 769 35.30
50 1750/2100 500 300/150 83.7 2.30/1.70 328AT D451 $8,240 GO-2AS Y 769 35.30
50 1150/2000 500 300/150 82.0 2.90/1.35 366AT D610 $10,577 GO-2AS N 860 35.90
60 1750/2100 500 300/150 97.0 2.40/1.60 L328AT D576 $9,430 GO-2AS Y 888 37.90
75 1750/2100 500 300/150 125.0 2.40/1.60 329AT D577 $11,077 GO-2AS Y 888 37.90
100 1750/2500 500 300/150 160.0 3.90/2.25 368AY D612 $16,514 GO-2AS N 1020 38.90 70,101,122
100 1750/2500 500 300/150 160.0 3.90/2.25 368AY D611 $16,514 GO-2AS N 1020 38.90 101,122
100 1750/2000 500 300/150 160.0 3.90/3.00 368AT D558 $13,892 GO-2AS N 1020 38.90
125 1750/2000 500 300/150 202.0 3.80/3.00 368AT D559 $16,450 GO-2AS N 1020 38.90
125 850/1700 500 300/150 203.0 3.70/1.72 506AT D613 $23,807 GO-2AS N 2290 49.70 7.3
150 1750/2000 500 300/150 242.0 4.00/3.37 407AT D560 $18,934 GO-2AS N 1300 40.10
150 1750/2000 500 300/150 242.0 4.00/3.37 407AY D614 $20,183 GO-2AS N 1300 40.60 101,122

DC Motors – Kinamatic™
150 1750/2000 500 300/150 242.0 4.00/3.37 407AY D592 $20,183 GO-2AS N 1300 40.60 70,101,122
150 850/1700 500 300/150 240.0 9.40/2.90 506AT D615 $26,933 GO-2AS N 2290 49.70
200 1750/2000 500 300/150 318.0 6.10/4.60 L409AY D593 $25,259 GO-2AS N 1650 48.60 70,101,122
200 1750/2000 500 300/150 318.0 6.10/4.60 L409AY D616 $25,259 GO-2AS N 1650 48.60 101,122
200 1750/2000 500 300/150 318.0 6.10/4.60 L409AT D574 $24,010 GO-2AS N 1650 48.10
250 1750/1900 500 300/150 400.0 4.40/3.90 504AY D594 $30,767 GO-2AS N 1900 46.80 70,101,122
250 1750/1900 500 300/150 400.0 4.40/3.90 504AY D617 $30,767 GO-2AS N 1900 46.80 101,122
250 1750/1900 500 300/150 400.0 4.30/3.87 504AT D575 $29,518 GO-2AS N 1900 45.70
250 1150/1700 500 300/150 401.0 6.50/3.48 506AT D618 $34,750 GO-2AS N 2290 49.70
300 1150/1600 500 300/150 480.0 6.40/4.00 508AT D619 $40,757 GO-2DS N 2810 54.70
400 1750/1900 500 300/150 629.0 6.42/5.50 508AT D489 $49,160 GO-2DS N 2810 54.70
500 1750/1900 500 300/150 781.0 8.10/6.80 5010AY D620 $65,720 GO-2DS N 4260 65.50 104
Notes
70 F-2 assembly
101 Oversized roller bearings
104 4 1/8" shaft diameter
122 Oversized shaft

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™
Type-C Power Supply
Pricing cont.

Base Mounted - GE CD180AT-CD500AT

Shunt Wound - Dripproof Fully Guarded - Blower Ventilated
Armature Armature Price C Dim
HP RPM Volts Field Volts Amps Field Amps Frame Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
7.5 1750/2300 240 300/150 26.5 0.95/0.52 189AT D418 $4,289 GO-2AS N 172 23.00
10 1750/2300 500 300/150 17.2 1.35/0.88 219AT D561 $4,729 GO-2AS N 272 25.20
15 1750/2300 500 300/150 25.2 1.60/0.88 258AT D562 $5,458 GO-2AS N 381 27.10
20 1750/2300 500 300/150 35.0 1.53/0.83 259AT D563 $6,092 GO-2AS N 423 28.80
20 1150/2000 500 300/150 33.9 1.98/0.94 327AT D650 $7,397 GO-2AS Y 752 33.40
25 1750/2300 500 300/150 42.7 1.76/1.20 287AT D564 $6,864 GO-2AS N 513 31.00
25 1150/2000 500 300/150 42.0 2.30/1.02 328AT D651 $8,440 GO-2AS N 830 35.30
30 1750/2300 500 300/150 50.4 2.08/1.16 288AT D565 $7,424 GO-2AS N 576 32.70
40 1750/2100 500 300/150 67.0 2.03/1.32 327AT D566 $8,649 GO-2AS N 752 33.40
50 1750/2100 500 300/150 82.0 2.30/1.70 328AT D567 $9,673 GO-2AS N 830 35.30
60 1750/2100 500 300/150 97.0 2.40/1.55 L328AT D578 $10,863 GO-2AS Y 949 37.90
60 1750/2100 500 300/150 97.2 3.40/2.38 365AT D652 $12,510 GO-2AS Y 815 33.70
60 1150/2000 500 300/150 97.0 4.00/1.78 368AT D654 $13,516 GO-2AS N 1085 38.90
75 1750/2100 500 300/150 125.0 2.40/1.60 329AT D579 $12,510 GO-2AS Y 949 37.90
75 1750/2100 500 300/150 125.0 2.40/1.60 329AT D655 $12,510 GO-2AS N 949 37.90 70
75 1750/2100 500 300/150 122.0 2.40/1.85 366AT D656 $13,748 GO-2AS Y 925 35.90
7.4 75 1750/2100 500 300/150 122.0 2.40/1.85 366AT D657 $13,748 GO-2AS N 925 35.90 70
75 1150/2000 500 300/150 123.0 3.80/1.80 368AT D658 $15,782 GO-2AS N 1085 38.90
100 1750/2000 500 300/150 160.0 3.90/3.00 368AT D467 $15,471 GO-2AS Y 1085 38.90
DC Motors – Kinamatic™

100 1150/2000 500 300/150 162.0 7.10/2.96 407AT D659 $18,933 GO-2AS N 1365 40.10
100 850/1700 500 300/150 614.0 6.00/2.40 409AT D660 $21,917 GO-2AS N 1665 44.60
125 1750/2000 500 300/150 202.0 3.80/3.00 368AT D468 $18,029 GO-2AS Y 1085 38.90
125 1150/2000 500 300/150 201.0 7.10/3.30 409AT D661 $21,917 GO-2AS N 1665 44.60
150 1750/2000 500 300/150 242.0 4.00/3.37 407AT D473 $20,513 GO-2AS Y 1365 40.10
150 1150/2000 500 300/150 244.0 7.29/3.54 409AT D662 $25,236 GO-2AS N 1665 44.60
200 1750/2000 500 300/150 318.0 6.10/4.60 L409AT D478 $25,863 GO-2AS Y 1720 48.00
200 1750/2000 500 300/150 318.0 6.10/4.60 L409AT D663 $25,863 GO-2AS N 1720 48.00 70
250 1750/1900 500 300/150 400.0 4.30/3.87 504AT D482 $31,371 GO-2AS Y 1982 45.70
250 1750/1900 500 300/150 400.0 4.30/3.87 504AT D664 $31,371 GO-2AS N 1982 45.70 70
300 850/1500 500 300/150 477.0 12.00/5.10 5010AY D490 $48,107 GO-2DS N 4343 65.50 17
400 1150/1500 500 300/150 631.0 8.20/5.50 5010AY D492 $60,809 GO-2DS N 4343 65.50 17
500 1150/1500 500 300/150 795.0 14.70/9.30 6058 D600 $76,964 GO-2DS N 5743 67.61
600 1750/1900 500 300/150 950.0 10.20/9.00 6063 D601 $99,367 GO-2DS N 6043 71.91
Notes
70 F-2 assembly
17 Shaft extension 4 1/8" diameter

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™
Type-C Power Supply
Pricing cont.

Base Mounted - GE CD180AT-CD500AT

Shunt Wound - Totally Enclosed
Armature Armature NEMA Norm Wt C Dim
HP RPM Volts Field Volts Amps Field Amps Frame Cat No. List Price Price Symbol Stk (lbs) (in) Notes
1 1750/2300 240 300/150 3.6 0.35/0.22 L182 D681 $2,073 GO-2AS N 83 15.30 55
1 1150/2000 240 240/120 3.7 0.53/0.21 L182 D680 $2,221 GO-2AS N 83 15.30 55
2 1750/2300 240 300/150 7.1 0.29/0.17 L186AT D553 $2,193 GO-2AS N 128 18.80 55
3 1750/2300 240 300/150 10.8 0.29/0.17 L186AT D530 $2,809 GO-2AS N 128 18.80 55
3 1750/2300 500 300/150 5.1 0.45/0.26 L186ATC D682 $3,282 GO-2AS Y 128 18.80 55, 77
5 1750/2300 240 300/150 17.6 0.38/0.24 189AT D408 $3,709 GO-2AS N 165 23.00 76
5 1750/2300 240 240/120 17.2 0.95/0.65 2110AT D684 $4,487 GO-2AS N 280 26.70 55
5 1750/2300 240 300/150 17.2 0.74/0.45 2110AT D683 $4,487 GO-2AS N 280 26.70 55
5 1750/2300 500 300/150 8.3 0.60/0.40 189AT D415 $3,709 GO-2AS N 165 23.00 76
5 1750/2300 500 300/150 8.2 0.76/0.52 2110AT D685 $4,487 GO-2AS Y 280 26.70 55
7.5 1750/2300 240 300/150 26.2 1.15/0.70 2110AT D430 $4,487 GO-2AS N 287 29.30 76
7.5 1750/2300 500 300/150 12.8 0.74/0.44 2110AT D429 $4,487 GO-2AS N 287 29.30 76
7.5 1750/2300 500 300/150 12.4 0.91/0.58 259AT D686 $5,446 GO-2AS N 403 28.90 55
10 1750/2300 240 300/150 34.3 0.88/0.55 259AT D440 $5,123 GO-2AS N 442 31.90
10 1750/2300 500 300/150 16.3 1.15/0.72 259AT D436 $5,123 GO-2AS N 442 31.90
15 1750/2300 240 300/150 51.7 0.98/0.68 288AT D568 $6,611 GO-2AS N 587 36.40
15 1750/2300 500 300/150 24.5 0.98/0.68 288AT D569 $6,611 GO-2AS N 587 36.40 7.5
20 1750/2300 240 300/150 68.5 1.24/0.86 327AT D570 $7,594 GO-2AS N 732 37.60
25 1750/2300 240 300/150 85.0 1.50/1.10 328AT D572 $8,893 GO-2AS N 812 39.50

DC Motors – Kinamatic™
30 1750/2300 240 300/150 103.0 1.80/1.30 366AT D460 $9,844 GO-2AS N 940 40.40
30 1750/2300 500 300/150 48.7 1.80/1.24 366AT D457 $9,844 GO-2AS N 940 40.40
40 1750/2100 240 300/150 136.0 0.95/0.76 368AT D469 $12,421 GO-2AS N 1100 43.40
40 1750/2100 500 300/150 64.6 1.49/1.20 368AT D463 $12,421 GO-2AS N 1100 43.40
50 1750/2100 500 150/300 80.7 1.49/1.20 409AT D554 $14,951 GO-2AS N 1680 49.40
75 1750/2100 500 300/150 120.0 1.50/1.25 409AT D474 $18,104 GO-2AS N 1680 49.40
Notes
55 TENV Construction
76 Accessory mounting faces not available for TEFC CD180AT and CD210AT frames
77 8 1/2" C-face rabbet

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™
Type-K Power Supply
Pricing
End Mounted
Permanent Magnet - Totally Enclosed
Price C Dim
HP RPM Volts Frame Base Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
3 1725 90 56C Bolt-On D273 $271 GO-1PM Y 19 10.42 55, 82
3 1725 180 56C Bolt-On D283 $281 GO-1PM N 19 10.42 55, 82
a 1725 90 56C Bolt-On D274 $376 GO-1PM Y 25 11.42 55, 82
a 1725 180 56C Bolt-On D284 $331 GO-1PM N 25 11.42 55, 82
2 2500 90 56C Bolt-On D285 $331 GO-1PM N 29 12.87 82
2 2500 180 56C Bolt-On D286 $321 GO-1PM N 29 12.87 82
2 1725 90 56C Bolt-On D275 $336 GO-1PM Y 29 12.87 82
2 1725 180 56C Bolt-On D276 $379 GO-1PM Y 29 12.87 82
: 2500 90 56C Bolt-On D287 $332 GO-1PM N 37 14.87 82
: 2500 180 56C Bolt-On D288 $345 GO-1PM N 37 14.87 82
: 1725 90 56C Bolt-On D277 $430 GO-1PM Y 39 14.87 82
: 1725 180 56C Bolt-On D278 $494 GO-1PM Y 43 14.87 82
1 2500 90 56C Bolt-On D289 $442 GO-1PM N 40 14.87 82
1 2500 180 146ATC NB D311 $1,439 GO-2PK3 N 67 15.60 85
1 2500 180 56C Bolt-On D290 $442 GO-1PM N 40 14.87 82
1 1725 90 56C Bolt-On D279 $624 GO-1PM Y 41 14.87 82
1 1725 180 56C Bolt-On D280 $624 GO-1PM Y 41 14.87 82
1 1150 180 148ATC NB D313 $1,448 GO-2PK3 N 77 16.90 85
1.5 2500 180 148ATC NB D314 $1,448 GO-2PK3 N 59 16.90 85
7.6 1.5 1725 180 148ATC NB D315 $1,208 GO-2PK3 Y 79 16.90 85
1.5 1150 180 1412ATC NB D316 $1,802 GO-2PK3 N 113 20.70 85
2 2500 180 148ATC NB D317 $1,448 GO-2PK3 N 78 16.90 85
DC Motors – Kinamatic™

2 1725 180 149ATC NB D318 $1,401 GO-2PK3 Y 88 18.00 85

2 1150 180 1412ATC NB D319 $1,956 GO-2PK3 Y 113 20.70 85
3 2500 180 1412ATC NB D320 $1,956 GO-2PK3 N 113 20.70 85
3 1725 180 1412ATC NB D321 $1,913 GO-2PK3 Y 115 20.70 85

Shunt Wound - Totally Enclosed

Armature Price
HP RPM Volts Field Volts Frame Base Cat No. List Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
3 1725 90 100 56C NB D115 $1,560 GO-1DC Y 24 11.20 55,85
a 1725 90 100 56C NB D167 $1,628 GO-1DC Y 29 11.94 55,85
2 1725 90 100 56C NB D116 $1,619 GO-1DC Y 41 13.87 55,85
2 1725 180 200 56C NB D169 $1,853 GO-1DC Y 42 13.87 55,85
: 1725 90 100 56C NB D117 $1,919 GO-1DC Y 52 15.94 85
: 1725 180 200 56C NB D135 $2,085 GO-1DC Y 55 15.94 85
1 2500/2750 180 200/100 146ATC NB D300 $1,038 GO-2SK3 N 55 15.60 85
1 1750/2050 180 200/100 146ATC NB D301 $1,062 GO-2SK3 Y 55 15.60 85
1 1725 180 200 56C NB D118 $1,838 GO-1DC Y 55 15.94 85
1 1150/1380 180 200/100 148ATC NB D302 $1,242 GO-2SK3 N 67 16.90 85
1.5 2500/2750 180 200/100 148ATC NB D303 $1,255 GO-2SK3 N 59 16.90 85
1.5 1750/2050 180 200/100 148ATC NB D304 $1,277 GO-2SK3 Y 67 20.70 85
1.5 1150/1380 180 200/100 1412ATC NB D305 $1,619 GO-2SK3 N 93 16.90 85
2 2500/2750 180 200/100 148ATC NB D306 $1,505 GO-2SK3 N 67 18.00 85
2 1750/2050 180 200/100 149ATC NB D307 $1,529 GO-2SK3 Y 77 20.70 85
2 1150/1380 180 200/100 1412ATC NB D308 $1,938 GO-2SK3 N 102 20.70 85
3 2500/2750 180 200/100 1412ATC NB D309 $1,938 GO-2SK3 N 102 20.70 85
3 1750/2050 180 200/100 1412ATC NB D310 $1,962 GO-2SK3 Y 102 20.70 85
Notes
55 TENV Construction
82 Base kit included unassembled with motor
85 Base kit available

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™
Type-K Power Supply
Pricing cont.

Base and End Mounted - NEMA 180-210 Frame

Shunt Wound - Dripproof
Armature Field Armature Price Norm Wt C Dim
HP RPM Volts Volts Amps Field Amps Frame Cat No. List Price Symbol Stk (lbs) (in) Notes
1 1750/2050 180 200/100 4.9 0.44/0.37 L182AT D585 $2,598 GO-2AS N 83 15.30
1 1750/2050 180 200/100 4.9 0.44/0.37 L182ACY D402 $2,684 GO-2AS N 80 15.30 78
1.5 1750/2050 180 200/100 7.3 0.44/0.37 L182ACY D536 $2,795 GO-2AS N 80 17.50 64, 78
2 1750/2050 180 200/100 9.4 0.59/0.39 186ACY D406 $2,906 GO-2AS N 102 16.80 78
2 1750/2050 180 200/100 9.4 0.59/0.39 186ATC D537 $2,906 GO-2AS N 102 16.80 77
3 1750/2050 180 200/100 14.4 0.59/0.39 186ATC D539 $2,824 GO-2AS Y 102 18.80 77
5 2500/2750 180 200/100 23.6 0.93/0.72 186AT D586 $2,631 GO-2AS N 105 16.80 64
5 1750/2050 180 200/100 24.1 0.75/0.54 L186ATC D413 $2,921 GO-2AS Y 128 18.80 64, 77
5 1750/2050 180 200/100 24.1 0.75/0.54 L186ATC D414 $4,058 GO-2AS N 128 18.80 77, 88
5 1750/2050 180 200/100 23.7 1.38/0.94 219ATC D428 $4,696 GO-2AS Y 261 25.20 77

7.7

Shunt Wound - Totally Enclosed

DC Motors – Kinamatic™
Armature Field Armature Price Norm Wt C Dim
HP RPM Volts Volts Amps Field Amps Frame Cat No. List Price Symbol Stk (lbs) (in) Notes
1 1750/2050 180 200/100 5.0 0.28/0.22 L182ATC D400 $2,649 GO-2AS N 80 15.30 55, 77
1 1750/2050 180 200/100 5.0 0.28/0.22 L182ACY D401 $2,649 GO-2AS N 80 15.30 55, 78
1.5 1750/2050 180 200/100 7.3 0.37/0.27 186ACY D405 $2,784 GO-2AS Y 102 16.80 55, 78
1.5 1750/2050 180 200/100 7.3 0.37/0.27 186ATC D540 $2,784 GO-2AS N 102 16.80 55, 77
2 1750/2050 180 200/100 9.5 0.48/0.37 L186ATC D411 $2,857 GO-2AS Y 128 18.80 55, 77
2 1750/2050 180 200/100 9.5 0.48/0.37 L186ACY D412 $2,857 GO-2AS Y 128 18.80 55, 78
3 1750/2050 180 200/100 13.9 0.63/0.46 189ACY D555 $2,994 GO-2AS N 160 20.80 55, 78
3 1750/2050 180 200/100 13.9 0.63/0.46 189ATC D419 $2,994 GO-2AS Y 160 80.80 55, 77
5 1750/2050 180 200/100 23.3 1.00/0.74 189ATC D420 $3,795 GO-2AS Y 160 20.80 58, 64, 76, 77
5 1750/2050 180 200/100 23.0 0.81/0.63 2110ATC D431 $5,497 GO-2AS Y 289 26.70 55, 77
5 1750/2050 180 200/100 23.3 1.00/0.74 189AT D583 $3,709 GO-2AS Y 162 20.80 58, 76, 64
5 1750/2050 180 200 23.0 0.80/0.60 2110ACY D584 $5,831 GO-2AS Y 389 8.50 55, 74, 77
Notes
55 TENV Construction
58 TEFC Construction
64 Suitable for constant torque to 60% of base speed
74 1.125" diameter shaft
76 Accessory mounting faces not available for TEFC CD180AT and CD210AT frames
77 8 1/2" C-face rabbet
78 4 1/2" C-face rabbet
88 Blower provided with filter

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Tachometers
PY Design
Pricing

AC Tachometer Generators – Totally Enclosed

Volts % GE List Price Norm Wt C Dim
RPM /1000RPM Ripple Frame Frame Bearings Base Rotation Cat No. Price Symbol Stk (lbs) (in) Notes
400-5000 20 NA 18 GE59 Ball WB Either or Reversing Service D246 $817 GO-7PTC Y 5 6.43 55
400-5000 28 NA 18 GE59 Ball FLG Either or Reversing Service D120 $681 GO-7PTC Y 5 6.00 55
400-5000 28 NA 18 GE59 Ball WB Either or Reversing Service D121 $681 GO-7PTC Y 4 6.00 55

7.8
DC Motors – Kinamatic™

DC Tachometer Generators – Totally Enclosed

Volts % GE List Price Norm Wt C Dim
RPM /1000RPM Ripple Frame Frame Bearings Base Rotation Cat No. Price Symbol Stk (lbs) (in) Notes
100-5000 50 0.50% 18 GE59 Ball FLG Either; Reversing Service to D123 $1,335 GO-7PTC N 7 7.47 55
2500RPM
100-5000 50 0.50% 18 GE59 Ball WB Either; Reversing Service to D125 $1,335 GO-7PTC N 7 7.59 55
2500RPM
100-5000 50 0.75% 18 GE59 Ball FLG Either; Reversing Service to D251 $1,635 GO-7PTC N 7 7.47 55
2500RPM
100-5000 50 1.00% 18 GE59 Ball FLG Either; Reversing Service to D252 $1,602 GO-7PTC N 7 7.47 55
5000RPM
100-2500 100 0.50% 18 GE59 Ball FLG Either or Reversing Service D122 $1,335 GO-7PTC N 8 7.47 55
100-2500 100 0.50% 18 GE59 Ball WB Either or Reversing Service D124 $1,335 GO-7PTC N 7 7.59 55
100-2500 100 0.75% 18 GE59 Ball FLG Either or Reversing Service D250 $1,635 GO-7PTC N 8 7.47 55
Notes
55 TENV Construction

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Tachometers
BC42 and BC46 Design
Pricing

DC Tachometer – Totally Enclosed Non-Ventilated

Volts NEMA
RPM /1000RPM GE Frame Frame Base Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
100-5000 50 42 56 Bolt-On D126 $1,901 GO-7PTC N 26 10.50 55
100-5000 50 46 56 Bolt-On D127 $2,994 GO-7PTC Y 36 11.72 55
100-5000 50 46 56C NB D130 $3,013 GO-7PTC Y 39 12.60 55
100-5000 50 42 56C NB D141 $1,923 GO-7PTC Y 29 10.50 55
100-5000 50 46 56C Bolt-On D144 $3,103 GO-7PTC Y 41 14.63 55, 22
100-3600 100 46 56 Bolt-On D128 $2,994 GO-7PTC Y 36 11.72 55
100-3600 100 46 56C NB D131 $3,013 GO-7PTC Y 39 12.60 55
100-3600 100 46 56C Bolt-On D132 $3,103 GO-7PTC Y 41 14.63 55, 22
100-3600 100 46 56 Bolt-On D139 $3,026 GO-7PTC Y 36 14.49 55, 22
100-2750 100 42 56 Bolt-On D136 $1,901 GO-7PTC Y 25 10.50 55
100-2750 100 42 56C NB D142 $1,923 GO-7PTC Y 29 10.50 55
100-2750 100 42 56C Bolt-On D143 $1,983 GO-7PTC Y 30 12.54 55, 22
100-1800 200 46 56C Bolt-On D133 $3,103 GO-7PTC Y 41 14.63 55, 22
100-1800 200 46 56 Bolt-On D138 $2,994 GO-7PTC Y 29 11.72 55
100-1800 200 46 56 Bolt-On D140 $3,026 GO-7PTC Y 36 14.49 55, 22
100-1375 200 42 56 Bolt-On D137 $1,901 GO-7PTC Y 26 10.50 55
100-5000 50 42 56C Bolt-On D149 $1,983 GO-7PTC Y 30 12.54 55, 22
Notes
22 Double shaft extension 1 7/8" long by 5/8" diameter each end
55 TENV Construction
7.9

DC Motors – Kinamatic™
DC Tachometer Generators – Explosion Proof
Class I, Group D; Class II, Group E, F, G
Volts NEMA
RPM /1000RPM GE Frame Frame Base Cat No. List Price Price Symbol Norm Stk Wt (lbs) C Dim (in) Notes
100-5000 50 18 56 WB D255 $2,182 GO-7PTC N 32 11.93 58
100-5000 50 18 56C NB D267 $2,195 GO-7PTC Y 38 11.88 58
100-2500 100 18 56 WB D256 $2,182 GO-7PTC Y 32 11.93 58
100-2500 100 18 56C NB D268 $2,195 GO-7PTC Y 38 11.88 58
Notes
58 TEFC Construction

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™
Low Voltage Battery Supply

End Mounted

Permanent Magnet - Totally Enclosed

NEMA Cat List C Dim
HP RPM Voltage Frame Base No. Price Price Symbol Norm Stk Wt (lbs) (in) Notes
3 1800 12 56C BOLT-ON D360 $316 GO-1PM Y 19 10.42 55
a 1800 12 56C BOLT-ON D361 $338 GO-1PM Y 25 11.42
a 1800 24 56C BOLT-ON D362 $325 GO-1PM Y 25 11.42
2 1800 12 56C BOLT-ON D363 $356 GO-1PM Y 29 12.87
2 1800 24 56C BOLT-ON D364 $343 GO-1PM Y 29 12.87
: 1800 12 56C BOLT-ON D365 $461 GO-1PM Y 36 14.90
: 1800 24 56C BOLT-ON D366 $433 GO-1PM Y 36 14.90
1 1800 24 56C BOLT-ON D367 $599 GO-1PM Y 41 14.90
Notes
55 TENV Construction

7.10
Dimensions
DC Motors – Kinamatic™

Frame C AG Key Length N YS N-W AH

56JA, 56HA 10.42 8.29 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56KA 11.42 9.29 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56KA 12.87 10.75 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56 PA, 56SA 14.87 12.75 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
All dimensions in inches

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™
MG Set Power Supply
Base Mounted - NEMA 56 Frame

Shunt or Compound Wound - Dripproof

Field NEMA List Price Wt C Dim
HP RPM Arm Volts Volts Frame Base Cat No. Price Symbol Norm Stk (lbs) (in) Notes
a 1725 115 115 56 WB D106 $1,388 GO-1DC Y 25 11.20
a 1725 NA 115 56 WB D109 $1,568 GO-1DC Y 26 11.20
2 1725 115 115 56 WB D107 $1,493 GO-1DC Y 28 12.00
2 1725 NA 115 56 WB D110 $1,845 GO-1DC Y 31 12.00

Shunt or Compound Wound - Dripproof

Field List Price Wt C Dim
HP RPM Arm Volts Volts NEMA Frame Base Cat No. Price Symbol Norm Stk (lbs) (in) Notes
3 1725 230 230 56 WB D111 $1,298 GO-1DC Y 23 10.80 55
3 1725 NA 230 56 WB D113 $1,418 GO-1DC Y 23 10.80 55
2 1725 230 230 56 WB D112 $1,673 GO-1DC Y 37 13.20 55
Notes
55 TENV Construction

7.11

DC Motors – Kinamatic™
Dimensions

Ref Frame Key Length C L

1 56K 1.51 1.49 13.19 6.03
2 56R 1.51 1.49 15.13 7.97
3 56N 1.51 1.49 13.94 6.78
4 56T 1.51 1.49 16.01 8.85
All dimensions in inches

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™
Totally Enclosed Fan Cooled
Motor Dimensions
Type CD, Dripproof Fully Guarded and Totally Enclosed Non-Ventilated, Frames L182AT to 189AT
COMMUTATOR END DRIVE END
FC 1 1
1.44 8.88 1.44
C
CONDUIT
HOLE 22.5∞
1.75 BS
2.39 R 5.20
.20
.75 NPT FOR
CONDUIT .14
2.25
KEY
1.50
.25 X .25 X 1.38 LG
KEY .1875 X .1875 3 2.00
.88 LONG
3 1.1250
ÿ
1.1245 R 4.92
8.93

.8750 4.50
ÿ
.8745 4 4.47 2

2.00
(4) HOLES 2F 2.76 1.50
3.75 .28
.4062 DIA.
B 7.50
MAX
8.90 MAX.

Approx Wk2 of Approx. Net.

Frame Arm. Lb. Ft.2 B C FC 2F BS Wt. (lbs)
L182AT 0.28 5.80 15.26 16.51 4.5 6.63 83
186AT 0.45 8.30 16.76 18.01 7.0 8.13 105
L186AT 0.67 8.30 18.76 20.01 7.0 10.13 128
7.12 189AT 0.77 11.56 20.76 22.01 10.0 12.13 162

1. Splashproof fully guarded machines will have additional covers, increasing the overall width at the
commutator-end and drive-end side air openings.
DC Motors – Kinamatic™

2. Dripproof, fully guarded vertical drive-end shaft down machines will have additional covers, increasing the
overall width and exceeding bottom feet at the commutator-end openings.

3. Represents minimum length of shaft available for hubs.

4. Air opening. For enclosure type and mounting position, see enclosure and mounting assembly. Totally
enclosed machines will not have openings or covers on drive-end.

The standard single shaft machine has the commutator end bearing bracket and shaft extension prepared to
accept accessories. For additional information, see 36C697103AA.

For blower ventilated, blower can only be mounted on side of motor because there is no air opening at the
top of the motor. The motor leads exit at the top of the motor.

Commutator-end shaft extension is furnished only when specifically ordered.

Shaft runout shall not exceed 0.002 inch total indicator reading.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded and Totally Enclosed Nonventilated, Frames L182ACY to 189ACY
4 1/2" Type C Face Mounting with Feet

COMMUTATOR END
C

AG 2.12
8.88 5.24 DRIVE
BV END COVER
22.5∞ .12
.70 .375-16 THREAD
1 .14 MAX. MINIMUM THREAD
CONDUIT ACCESSORY ENGAGEMENT .50; MAX
1.44 HOLE 1
MOUNTING BS 2.00 BOLT PENETRATION .62-
R 5.20 1.44 FACE (4) HOLES, EQUALLY
.75 NPT FOR 3 KEY
CONDUIT .1875 X .1875 X .88 LG SPACED

ÿ6.50
ÿ5.88
8.94 ÿ8.82
ÿ4.500 MAX.
2 4.497
R 4.92 .12
4
4.50 ÿ.8750
4.47 .8745
4

1.50 (4) HOLES

.38 2.00 .4062 DIA. .13
3.75
2F 2.75
7.50
B 2.25
8.90 MAX. MAX

Approx Wk2 of Approx. Net.

Frame Arm. Lb. Ft.2 B C 2F AG BS BV Wt. (lbs)
L182ACY 0.28 5.80 15.26 4.5 13.14 6.63 9.51 83
7.13
186ACY 0.45 8.30 16.76 7.0 14.64 8.13 11.01 105
L186ACY 0.67 8.30 18.76 7.0 16.64 10.13 13.01 128

DC Motors – Kinamatic™
189ACY 0.77 11.56 20.76 10.0 18.64 12.13 15.01 162
1. Splashproof fully guarded machines will have additional covers, increasing the overall width at
the commutator-end and drive-end side air openings.

2. Dripproof, fully guarded vertical drive-end shaft down machines will have additional covers,
increasing the overall width and exceeding bottom of mounting feet at the commutator-end
openings.

3. Represents minimum length of shaft available for hubs.

4. Air opening. For enclosure type and mounting position, see enclosure and mounting assembly.
Totally enclosed machines will not have openings or covers on drive-end.

Mounting face will be square and rabbet diameter concentric with shaft within .004 inch total
indicator reading. Shaft runout not to exceed .002 inch total indicator reading.

Feet will be supplied unless otherwise specified.

The standard single shaft machine has the commutator-end bearing bracket and shaft extension
prepared to accept accessories. For additional information, see 36C697103AA.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded & Totally Enclosed Nonventilated, Frames L182ATC to 189 ATC
8 1/2" Type C Face Mounting with Feet
COMMUTATOR END
C
AG 2.12
8.88 5.24 DRIVE
BV END COVER
22.5∞ .30
.70 .375-16 THREAD
MIN. MINIMUM THREAD
1
CONDUIT ACCESSORY ENGAGEMENT .50; MAX
1.44 HOLE 1
MOUNTING BS 2.00 BOLT PENETRATION .62-
R 5.20 1.44 FACE (4) HOLES, EQUALLY
.75 NPT FOR 3 KEY
CONDUIT .25 X .25 X 1.38 LG SPACED

ÿ8.50 ÿ5.88
8.94
ÿ8.82
2 MAX.
R 4.92 .12
4
4.50 ÿ1.1250
4.47 1.1245
4

1.50 (4) HOLES

.38 2.00 .4062 DIA. .13
3.75
2F 2.75
7.50
B 2.25
8.90 MAX. MAX

Approx Wk2 of
Frame Arm. Lb. Ft.2 B C FC 2F BS BV
L182ATC 0.28 5.80 15.26 16.51 4.5 6.63 9.51
186ATC 0.45 8.30 16.76 18.01 7.0 8.13 11.01

7.14 L186ATC 0.67 8.30 18.76 20.01 7.0 10.13 13.01

189ATC 0.77 11.56 20.76 22.01 10.0 12.13 15.01

1. Splashproof fully guarded machines will have additional covers, increasing the overall width at
DC Motors – Kinamatic™

the commutator-end and drive-end side air openings.

2. Dripproof, fully guarded vertical drive-end shaft down machines will have additional covers,
increasing the overall width and exceeding bottom of mounting feet at the commutator-end
openings.

3. Represents minimum length of shaft available for hubs.

4. Air opening. For enclosure type and mounting position, see enclosure and mounting assembly.
Totally enclosed machines will not have openings or covers on drive-end.

Mounting face will be square and rabbet diameter concentric with shaft within .004 inch total
indicator reading. Shaft runout not to exceed .002 inch total indicator reading.

Feet will be supplied unless otherwise specified.

The standard single shaft machine has the commutator-end bearing bracket and shaft extension
prepared to accept accessories. For additional information, see 36C697103AA.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded and Totally Enclosed Nonventilated, Frames L182ACY to 189ACY
4 1/2" Type C Face Mounting with Feet

COMMUTATOR END DRIVE END 9.94 DIA.

FC
8.88
C
CONDUIT
BS HOLE 22.5∞
2.39 R 5.20
1.75 .75 NPT FOR
CONDUIT .14

1.50 2.25
KEY
.25 X .25 X 1.38 LG
2.00
KEY .1875 X .1875
.88 LONG
1.1250
ÿ
1.1245
8.94

.8750 AIR 4.50

ÿ
.8745 OUT 4.47

AIR
IN
2.00
1.50
2F 2.75 3.75 .38
(4) HOLES
.4062 DIA.
B 7.50
MAX
8.90 MAX.

Approx Wk2 of Approx. Net.

Frame Arm. Lb. Ft.2 B C FC 2F BS Wt. (lbs)
L182ATC 0.28 5.80 17.45 19.47 4.5 6.63 83
7.15
186ATC 0.45 8.30 18.95 20.97 7.0 8.13 105
L186ATC 0.67 8.30 20.95 22.97 7.0 10.13 128

DC Motors – Kinamatic™
189ATC 0.77 11.56 22.95 24.97 10.0 12.13 165
1. Represents minimum length of shaft available for hubs.
For mounting position see enclosure and mounting assembly.
Shaft runout shall not exceed .002 inch total indicator reading.
Commutator end-shaft extension is furnished only when specifically ordered.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Totally Enclosed Fan Cooled, Frames L182ACY to 189ACY
4 1/2" Type C Face Mounting with Feet
COMMUTATOR END
C
AG
2.12
9.94 ÿ 8.88
BV
22.5∞ .12
.375-16 THREAD
.14 MAX. MINIMUM THREAD
CONDUIT ENGAGEMENT .50; MAX
HOLE BS 2.00 BOLT PENETRATION .62-
R 5.20 .75 NPT FOR 3 KEY (4) HOLES, EQUALLY
CONDUIT .1875 X .1875 X .88 LG SPACED

AIR IN

ÿ6.50
45∞

8.94 ÿ8.82
ÿ4.500 MAX.
4.497
.12
AIR
4.50 OUT ÿ.8750 ÿ5.88
4.47 .8745

1.50 2.00 (4) HOLES

.38 .4062 DIA. .13
3.75
2F 2.75
7.50
B 2.25
8.90 MAX. MAX

Approx Wk2 of Approx. Net.

Frame Arm. Lb. Ft.2 B C 2F AG BS BV Wt. (lbs)
L182ACY 0.28 5.80 17.45 4.5 15.33 6.63 9.51 83
7.16
186ACY 0.45 8.30 18.95 7.0 16.83 8.13 11.01 105
L186ACY 0.67 8.30 20.95 7.0 18.83 10.13 13.01 128
DC Motors – Kinamatic™

189ACY 0.77 11.56 22.95 10.0 20.83 12.13 15.01 165

1. Represents minimum length of shaft available for hubs.
For mounting position see enclosure and mounting assembly.
Mounting face will be square and rabbet diameter concentric with shaft within .004 inch total indicator.
Feet will be supplied unless otherwise specified.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded* Splashproof, Totally Enclosed Nonventilated,
Frames 218AT to 329AT with Feet
FC
COMMUTATOR END X2 P X2
C
AB

AC
.70 ACCESSORY N
MOUNTING FACE
FN N-W

XN
FV
V
0.20"

U U
XL
O
BS AIR AF
INLET D

AIR
FN-FW OUTLET
HOLE FOR
FW W AA CONDUIT G
K APPROX E J
AIR
INLET
2F BA H - HOLE 2E

B A

Drive End Key Commutator End Key Dimmensions in Inches

Approx Approx Wk2
Net Wt. of Arm Lb. Length Length
Frames (lbs) Ft.2 Width Thick ±.03 Width Thick ±.03 A Max B Max C D1 E 2F G H J K
218AT 234 1.35 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 11.56 24.22 5.25 4.25 10.0 0.50 0.4062 2.00 2.2
219AT 252 1.49 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 12.56 25.22 5.25 4.25 11.0 0.50 0.4062 2.00 2.2
2110AT 580 1.17 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 14.06 26.72 5.25 4.25 12.5 0.50 0.4062 2.00 2.2
258AT 361 2.91 0.3750 0.3750 2.25 0.3125 0.3125 1.50 12.40 14.06 27.14 6.25 5.00 12.5 0.62 0.5312 2.25 2.0
259AT 403 3.31 0.3750 0.3750 2.25 0.3125 0.3125 1.50 12.40 15.56 28.76 6.25 5.00 14.0 0.62 0.5312 2.25 2.0
287AT 493 4.67 0.5000 0.5000 2.25 0.3750 0.3750 2.00 13.88 14.16 30.98 7.00 5.50 12.5 0.64 0.5312 2.50 2.0
7.17
288AT 548 5.36 0.5000 0.5000 2.50 0.3750 0.3750 2.00 13.88 15.66 32.72 7.00 5.50 14.0 0.64 0.5312 2.50 2.0
327AT 691 8.45 0.5000 0.5000 2.50 0.5000 0.5000 2.25 15.88 15.96 33.44 8.00 6.25 14.0 0.75 0.6562 3.00 2.3

DC Motors – Kinamatic™
328AT 769 9.67 0.5000 0.5000 3.00 0.5000 0.5000 2.25 15.88 17.96 35.32 8.00 6.25 16.0 0.75 0.6562 3.00 2.3
329AT 888 11.4 0.5000 0.5000 3.00 0.5000 0.5000 2.25 15.88 19.96 37.94 8.00 6.25 18.0 0.75 0.6562 3.00 2.3

Dimensions in Inches
Frame AA=1.25 AA=2.00 AA=3.00
Size AB AC AF XL XN AB AC AF XL XN AB AC AF XL XN
210AT 9.62 7.56 3.62 5.94 4.38 11.48 8.92 4.62 7.38 5.38
Not Available
250AT 10.62 8.58 3.62 5.94 4.38 11.74 9.18 4.62 7.38 5.38
280AT 11.34 9.28 3.62 5.94 4.38 12.46 9.90 4.62 7.38 5.38 14.90 11.28 6.62 10.50 8.56
320AT Not Available 13.44 10.88 4.62 7.38 5.38 15.12 11.50 6.62 10.50 8.56

Dimensions in Inches
Frame N O P U4 V3 W N-W BA FC FN FU4 FV3 FW FN-FW BS XZ2
218AT 2.91 10.46 10.42 1.375 2.5 0.16 2.75 3.50 25.97 2.45 1.125 2.0 0.2 2.25 8.36 1.5
219AT 2.91 10.46 10.42 1.375 2.5 0.16 2.75 3.50 26.97 2.45 1.125 2.0 0.2 2.25 9.36 1.5
2110AT 2.91 10.46 10.42 1.375 2.5 0.16 2.75 3.50 28.47 2.45 1.125 2.0 0.2 2.25 10.87 1.5
258AT 3.41 12.46 12.42 1.625 3.0 0.16 3.25 4.25 29.39 2.95 1.375 2.5 0.2 2.75 9.65 1.5
259AT 3.41 12.46 12.42 1.625 3.0 0.16 3.25 4.25 31.01 2.95 1.375 2.5 0.2 2.75 11.26 1.5
287AT 3.91 13.94 13.88 1.875 3.5 0.16 3.75 4.75 33.75 3.45 1.625 3.0 0.2 3.25 10.89 1.5
288AT 3.91 13.94 13.88 1.875 3.5 0.16 3.75 4.75 35.47 3.45 1.625 3.0 0.2 3.25 12.62 1.5
327AT 4.41 15.94 15.88 2.125 4.0 0.16 4.25 5.25 36.69 3.95 1.875 3.5 0.2 3.75 11.80 1.5
328AT 4.41 15.94 15.88 2.125 4.0 0.16 4.25 5.25 38.57 3.95 1.875 3.5 0.2 3.75 13.68 1.5
329AT 4.41 15.94 15.88 2.125 4.0 0.16 4.25 5.25 41.19 3.95 1.875 3.5 0.2 3.75 16.30 1.5
* Dripproof, fully guarded machines can be used for wall or ceiling mounting. Assembly modifications must be made to maintain proper enclosure.
1. Dimension “D” Will not be exceeded. When exact dimension is required, shims up to .03 inch may be necessary where dimension “D” is 8 inches or less. When dimension “D” is over
8 inches, shims up to .06 may be necessary.
2. Splashproof machines will have additional covers, increasing the overall width at the commutator-end and drive-end side cover openings.
3. "V" represents minimum length of shaft available for hubs.
4. Shaft diameters 1.50 inches and smaller will come within the limits of +0.0000 inc -0.0005 inch. Diameters larger than 1.5 inches will come withing the limits of +0.0000 inch -0.0010 inch.
Shaft runout on diameters 1.625 inches and smaller shall not exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not exceed .003 inch indicator reading.

Conduit box will be assembled on the right hand side facing the commutator-end for motors and on the left hand side facing commutator-end for generators. Conduit box will be assembled
on opposite side of frame if so specified. Conduit box may be turned so that entrance may be made upward, downward from commutator-end or drive-end. Dimensions pertaining to
conduit boxes vary according to rating. Refer to GE Industrial Systems for dimensions. The standard single shaft maching has the commutator-end bearing bracket and shaft prepared to
accept accessories. For additional information, see 36C697103AA. Commutator-end shaft extension is furnished only when specifically ordered, and is prepared for accessory drive.
For shipping weight add 15% to net weight.
 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded* Splashproof, Totally Enclosed Nonventilated
Frames 218AT to 329AT with feet
FC BF TAP (4) HOLES
COMMUTATOR END EQUALLY SPACED
C
X2 P X2
.70 BV AH
AB
ACCESSORY
MOUNTING FACE BB AC
FN
MIN.
FV
XN
V
.20
AK
AJ
BD
FU U MAX.

XL O
W
AF
BS
AIR D
OUTLET

BC
FW HOLE FOR
K APPROX G
N-W AA CONDUIT
AIR E J
FN-FW BA H - HOLE
INLET 2F
N 2E

B A
AIR
OUTLET

Approx Approx Drive End Key Comm. End Key Dimensions in Inches
Net Wk2 of
Wt. Arm Lb. Lengt Length A B
Frames (lbs) Ft.2 Width Thick h ±.03 Width Thick ±.03 Max Max C D1 E 2F G H J K N O P U4 V3 W N-W
218ATC 234 1.35 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 11.56 24.22 5.25 4.25 10.0 0.50 0.4062 2.00 2.2 2.97 10.46 10.42 1.375 2.5 0.22 2.75
219ATC 261 1.49 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 12.56 25.22 5.25 4.25 11.0 0.50 0.4062 2.00 2.2 2.97 10.46 10.42 1.375 2.5 0.22 2.75
2110ATC 389 1.71 0.3125 0.3125 1.75 0.2500 0.2500 1.00 10.40 14.06 26.72 5.25 4.25 12.5 0.50 0.4062 2.00 2.2 2.97 10.46 10.42 1.375 2.5 0.22 2.75
258ATC 378 2.91 0.3750 0.3750 2.25 0.3125 0.3125 1.50 12.40 14.06 27.14 6.25 5.00 12.5 0.62 0.5312 2.25 2.0 3.47 12.46 12.42 1.625 3.0 0.22 3.25
7.18 259ATC 420 3.31 0.3750 0.3750 2.25 0.3125 0.3125 1.50 12.40 15.56 28.76 6.25 5.00 14.0 0.62 0.5312 2.25 2.0 3.47 12.46 12.42 1.625 3.0 0.22 3.25
287ATC 522 4.67 0.5000 0.5000 2.50 0.3750 0.3750 2.00 13.88 14.16 30.98 7.00 5.50 12.5 0.64 0.5312 2.50 2.0 3.97 13.94 13.88 1.875 3.5 0.22 3.75
288ATC 577 5.36 0.5000 0.5000 2.50 0.3750 0.3750 2.00 13.88 15.66 32.72 7.00 5.50 14.0 0.64 0.5312 2.50 2.0 3.97 13.94 13.88 1.875 3.5 0.22 3.75
DC Motors – Kinamatic™

327ATC 720 8.45 0.5000 0.5000 3.00 0.5000 0.5000 2.25 15.88 15.96 33.44 8.00 6.25 14.0 0.75 0.6562 3.00 2.3 4.47 15.94 15.88 2.125 4.0 0.22 4.25
328ATC 798 9.67 0.5000 0.5000 3.00 0.5000 0.5000 2.25 15.88 17.96 35.32 8.00 6.25 16.0 0.75 0.6562 3.00 2.3 4.47 15.94 15.88 2.125 4.0 0.22 4.25
329ATC 917 11.4 0.5000 0.5000 3.00 0.5000 0.5000 2.25 15.88 19.96 37.94 8.00 6.25 18.0 0.75 0.6562 3.00 2.3 4.47 15.94 15.88 2.125 4.0 0.22 4.25

Dimensions in Inches
Frame AA=1.25 AA=2.00 AA=3.00
Size AB AC AF XL XN AB AC AF XL XN AB AC AF XL XN
210ATC 9.62 7.56 3.62 5.94 4.38 11.48 8.92 4.62 7.38 5.38
Not Available
250ATC 10.62 8.56 3.62 5.94 4.38 11.74 9.18 4.62 7.38 5.38
280ATC 11.34 9.28 3.62 5.94 4.38 12.46 9.90 4.62 7.38 5.38 14.90 11.28 6.62 10.5 8.56
320ATC Not Available 13.44 10.88 4.62 7.38 5.38 15.12 11.50 6.62 10.5 8.56

Dimensions in Inches
BF
Frame BA BB Min FN FU4 BC Tap Depth FV3 FW FN-FW AH AJ AK ZA2 BD Max BV BS FC
218ATC 3.50 0.3 2.45 1.125 0.25 .500-13 1.00 2.0 0.2 2.25 1.125 7.25 8.5 1.5 9.00 12.11 8.36 25.97
219ATC 3.50 0.3 2.45 1.125 0.25 .500-13 1.00 2.0 0.2 2.25 1.125 7.25 8.5 1.5 9.00 13.11 9.36 26.97
2110ATC 3.50 0.3 2.45 1.125 0.25 .500-13 1.00 2.0 0.2 2.25 2.500 7.25 8.5 1.5 9.00 14.62 10.87 28.47
258ATC 4.25 0.3 2.95 1.375 0.24 .500-13 1.00 2.5 0.2 2.75 2.500 7.25 8.5 1.5 10.00 14.14 9.65 29.39
259ATC 4.25 0.3 2.95 1.375 0.24 .500-16 1.00 2.5 0.2 2.75 2.500 7.25 8.5 1.5 10.00 15.75 11.26 31.01
287ATC 4.75 0.3 3.45 1.625 0.24 .500-13 1.00 3.0 0.2 3.25 3.000 9.00 10.5 1.5 11.25 15.88 10.87 33.73
288ATC 4.75 0.3 3.45 1.625 0.24 .500-13 1.00 3.0 0.2 3.25 3.000 9.00 10.5 1.5 11.25 17.61 12.62 35.47
327ATC 5.25 0.3 3.95 1.875 0.24 .500-11 1.25 3.5 0.2 3.75 3.750 11.00 12.5 1.5 14.00 17.29 11.80 36.69
328ATC 5.25 0.3 3.95 1.875 0.24 .500-11 1.25 3.5 0.2 3.75 3.750 11.00 12.5 1.5 14.00 19.17 13.68 38.57
329ATC 5.25 0.3 3.95 1.875 0.24 .500-11 1.25 3.5 0.2 3.75 3.750 11.00 12.5 1.5 14.00 21.79 13.68 41.19
* Dripproof, fully guarded machines can be used for wall or ceiling mounting. Assembly modifications must be made to maintain proper enclosure.
1. Dimension “D” Will not be exceeded. When exact dimension is required, shims up to .03 inch may be necessary where dimension “D” is 8" or less. When dimension “D” is over 8", shims up to .06 may be necessary.
2. Splashproof machines will have additional covers, increasing the overall width at the commutator-end and drive-end side cover openings.
3. "V" represents minimum length of shaft available for hubs
4. Shaft diameters 1.50" and smaller will come within the limits of +0.0000–0.0005 inch. Diameters larger than 1.5" will come within the limits of +0.0000–0.0010 inch.
Shaft runout on diameters 1.625" and smaller shall not exceed .002" indicator reading. Diameters larger than 1.625" shall not exceed .003" indicator reading.
Conduit box will be assembled on the right hand side facing the commutator-end for motors and on the left hand side facing commutator-end for generators. Conduit box will be assembled on opposite side of
frame if so specified. Conduit box may be turned so that entrance may be made upward, downward from commutator-end or drive-end. Dimensions pertaining to conduit boxes vary according to rating.
Refer to GE Industrial Systems for dimensions. The standard single shaft maching has the commutator-end bearing bracket and shaft prepared to accept accessories. For additional information, see
36C697103AA.
Commutator-end shaft extension is furnished only when specifically ordered, and is prepared for accessory drive.
For shipping weight add 15% to net weight.
 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Totally Enclosed Fan Cooled, Frames 218AT to 2110AT with Feet
11.70 DIA.

FC 10.41

COMMUTATOR END KEY .3125 X .3125 X AB

C 1.75 LONG
2.45
2.91 AC
AIR
.20 OUT .15
2.25 2.75
2.00 2.50
KEY .25 X .25 X 1
XN
1
1.00 LONG

11.25

BS
AF
1.1250 5.25
ÿ1.3750 5.22
1.1245 1.3745

AIR
IN

5 2.20 APPROX. 3.50 HOLE FOR 4.25

3 AA CONDUIT .50 2.00
2F
.4062 DIA.
(4) HOLES 8.50
B
MAX. 10.40
MAX.

Approx Net.
Frame B C FC 2F BS Wt. (lbs.)
218AT 11.56 26.82 29.34 10.00 8.36 241
219AT 12.56 27.82 30.34 11.00 9.36 259
2110AT 14.06 29.32 31.84 12.50 10.87 287

7.19
Conduit Box Dimensions
AA AB AC AF XL XN

DC Motors – Kinamatic™
1.25 9.62 7.56 3.62 5.94 4.38
2 11.48 8.92 4.62 7.38 5.38

1. Represents minimum length of shaft available for hubs.

2. Machine can be used for wall or ceiling mounting.
3. Conduit box may be turned so that entrance can be made upward, downward, from commutator-end or drive-end,
providing mounting conditions permit. Conduit box will be assembled on opposite side of frame, if so specified.
Dimensions pertaining to conduit boxes vary according to rating.
4. Shaft runout shall no exceed 0.002 inch total indicator reading on drive-end.
5. Shroud is removable to permit access to handhole covers.
6. Commutator end-shaft extension is furnished only when specifically ordered.
7. For shipping weight, add 15% to net weight.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Totally Enclosed Fan Cooled, Frames 285AT to 328AT with Feet
FC
COMMUTATOR END
C
X2 P X2
.93
ACCESSORY MOUNTING FACE AB
N AC
.06
N-W
XN
V

.20

XL O

AF
FU BS D

FN-FW HOLE FOR

K APPROX BA
AA CONDUIT J G
E
FW H - HOLE
2F
2E
A
B

Approx Approx Wk2 Drive End Key Commutator End Key Dimmensions in Inches
Net Wt. of Arm Lb. Length Length
PG230
Frames (lbs) Ft.2 Width Thick ±.03 Width Thick ±.03 A Max B Max C D1 E 2F G H J K
258AT 397 3.17 0.375 0.375 2.25 0.3125 0.3125 1.50 12.40 14.06 30.32 6.25 5.00 12.5 0.62 0.5312 2.25 2.0
259AT 442 3.57 0.375 0.375 2.25 0.3125 0.3125 1.50 12.40 15.56 31.94 6.25 5.00 14.0 0.62 0.5312 2.25 2.0
287AT 532 5.09 0.500 0.500 2.50 0.3750 0.3750 2.00 13.88 14.16 34.66 7.00 5.50 12.5 0.64 0.5312 2.50 2.0
288AT 587 5.78 0.500 0.500 2.50 0.3750 0.3750 2.00 13.88 15.66 36.40 7.00 5.50 14.0 0.64 0.5312 2.50 2.0
7.20 327AT 732 9.20 0.500 0.500 3.00 0.5000 0.5000 2.25 15.88 15.96 37.62 8.00 6.25 14.0 0.75 0.6562 3.00 2.3
328AT 812 10.42 0.500 0.500 3.00 0.5000 0.5000 2.25 15.88 17.96 39.50 8.00 6.25 16.0 0.75 0.6562 3.00 2.3

Dimensions in Inches
DC Motors – Kinamatic™

Frame N O P U3 V2 W N-W BA FC FN FU3 FV2 FW FN-FW BS XP

258AT 3.41 12.75 13.00 1.625 3.0 0.16 3.25 4.25 32.64 3.25 1.375 2.5 0.5 2.75 9.65 12.42
259AT 3.41 12.75 13.00 1.625 3.0 0.16 3.25 4.25 34.26 3.25 1.375 2.5 0.5 2.75 11.26 12.42
287AT 3.91 14.25 14.52 1.875 3.5 0.16 3.75 4.75 37.48 3.75 1.625 3.0 0.5 3.25 10.89 13.88
288AT 3.91 14.25 14.52 1.875 3.5 0.16 3.75 4.75 39.22 3.75 1.625 3.0 0.5 3.25 12.62 13.88
327AT 4.41 16.25 16.52 2.125 4.0 0.16 4.25 5.25 40.94 4.25 1.875 3.5 0.5 3.75 11.80 15.88
328AT 4.41 16.25 16.52 2.125 4.0 0.16 4.25 5.25 42.82 4.25 1.875 3.5 0.5 3.75 13.68 15.88
Dimensions in Inches
Frame AA=1.25 AA=2.00 AA=3.00
Size AB AC AF XL XN AB AC AF XL XN AB AC AF XL XN
210AT 9.62 7.56 3.62 5.94 4.38 11.48 8.92 4.62 7.38 5.38
Not Available
250AT 10.62 8.56 3.62 5.94 4.38 11.74 9.18 4.62 7.38 5.38
280AT 11.34 9.28 3.62 5.94 4.38 12.46 9.90 4.62 7.38 5.38 14.90 11.28 6.62 10.5 8.56
320AT Not Available 13.44 10.88 4.62 7.38 5.38 15.12 11.50 6.62 10.5 8.56
1. Dimension "D" Will not be exceeded. When exact dimension is required, shims up to .03 inch may be necessary where dimension "D" is 8 inches or less.
When dimension “D” is over 8", shims up to .06 may be necessary.

2. "V" represents minimum length of shaft available for hubs.

Machine can be used for wall or ceiling mounting. Conduit box will be assembled on the right hand side facing the commutator-end for motors and on the
left hand side facing commutator-end for generators. Conduit box will be assembled on opposite side of frame if so specified. Conduit box may be turned
so that entrance may be made upward, downward from commutator-end or drive-end. Dimensions pertaining to conduit boxes vary according to rating.
Refer to GE Industrial Systems for dimensions.

3. Shaft diameters 1.50 inches and smaller will come within the limits of +0.0000 inch -0.0005 inch. Diameters larger than 1.5 inches will come within the
limits of +0.0000 inch -0.0010 inch.
Shaft runout on diameters 1.625 inches and smaller shall not exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not exceed .003
inch indicator reading.
Commutator-end shaft extension is furnished only when specifically ordered, and is prepared for accessory drive.
For shipping weight, add 15% to net weight.
When commutator-end shaft is not furnished, shaft and fan shroud on the commutator-end is prepared for shaft driven accessories. Refer to
36C697103BA for dimensions.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Dripproof Fully Guarded*, Splashproof, Totally Enclosed Nonventilated
Frames 365AT to 5010AY with Feet
FC
COMMUTATOR END X2 P X2
C
AB

AC
.70 ACCESSORY N
MOUNTING FACE
FN N-W

XN
FV
V
0.20"

U U
XL
O
BS AIR AF
INLET D

AIR
FN-FW OUTLET
HOLE FOR
FW W AA CONDUIT
K APPROX E J G
AIR
INLET
2F BA H - HOLE 2E

B A

Approx Approx Wk
2 Drive End Key Commutator End Key Dimmensions in Inches
Net Wt. of Arm Length Length
Frames (lbs) Lb. Ft. 2
Width Thick ±.03 Width Thick ±.03 A Max B Max C D1 E 2F G H J K N
365AT 750 15.61 0.625 0.625 3.50 0.500 0.500 3.00 17.92 14.16 33.70 9.0 7 12.25 0.74 0.8125 3.26 2.31 4.92
366AT 860 18.27 0.625 0.625 3.50 0.500 0.500 3.00 17.92 15.90 35.90 9.0 7 14.00 0.74 0.8125 3.26 2.31 4.92
368AT 1020 22.21 0.625 0.625 3.50 0.500 0.500 3.00 17.92 19.90 38.90 9.0 7 18.00 0.74 0.8125 3.26 2.31 4.92
407AT 1300 35.47 0.625 0.625 4.00 0.625 0.625 3.50 20.00 20.16 40.12 10.0 8 18.00 0.86 0.9375 4.00 2.38 5.42
L407AT 1350 35.54 0.625 0.625 4.00 0.625 0.625 3.50 20.00 20.16 43.52 10.0 8 18.00 0.86 0.9375 4.00 2.38 5.42
7.21
409AT 1600 43.81 0.625 0.625 4.00 0.625 0.625 3.50 20.00 24.16 44.62 10.0 8 22.00 0.86 0.9375 4.00 2.38 5.42
L409AT 1650 43.88 0.625 0.625 4.00 0.625 0.625 3.50 20.00 24.16 48.02 10.0 8 22.00 0.86 0.9375 4.00 2.38 5.42

DC Motors – Kinamatic™
504AT 1900 79.10 0.750 0.750 5.25 0.750 0.750 4.50 24.92 18.96 45.74 12.5 10 16.00 1.11 1.1875 4.50 3.00 6.67
L504AT 2070 79.15 0.750 0.750 5.25 0.750 0.750 4.50 24.92 18.96 47.50 12.5 10 16.00 1.11 1.1875 4.50 3.00 6.67
506AT 2290 98.76 0.750 0.750 5.25 0.750 0.750 4.50 24.92 22.96 49.74 12.5 10 20.00 1.11 1.1875 4.50 3.00 6.67
L506AT 2440 98.81 0.750 0.750 5.25 0.750 0.750 4.50 24.92 22.96 51.50 12.5 10 20.00 1.11 1.1875 4.50 3.00 6.67
508AT 2810 121.87 0.750 0.750 5.25 0.750 0.750 4.50 24.92 27.96 54.74 12.5 10 25.00 1.11 1.1875 4.50 3.00 6.67
L508AT 2970 122.92 0.750 0.750 5.25 0.750 0.750 4.50 24.92 27.96 56.50 12.5 10 25.00 1.11 1.1875 4.50 3.00 6.67
5010AY 4260 157.28 1.000 1.000 6.50 0.750 0.750 5.25 24.92 34.88 65.49 12.5 10 32.00 1.11 1.1875 4.50 3.00 8.42

Dimensions continued (For Conduit Box Dimensions, refer to publication GEP-387K, Page 124) BS
Frame AA= AA= AA= AA=
Size O P U3 V4 W N-W BA FC FN FU3 FV4 FW FN-FW 3" 4" (2) 4" Blank XZ2
365AT 17.91 17.90 2.375 4.50 0.17 4.75 5.875 37.45 4.45 2.125 4.00 0.2 4.25 9.02 9.02 6.64 - 0.25
366AT 17.91 17.90 2.375 4.50 0.17 4.75 5.875 39.65 4.45 2.125 4.00 0.2 4.25 11.22 11.22 8.84 - 0.25
368AT 17.91 17.90 2.375 4.50 0.17 4.75 5.875 32.65 4.45 2.125 4.00 0.2 4.25 14.22 14.22 11.84 - 0.25
407AT 20.15 20.38 2.625 5.00 0.17 5.25 6.625 44.37 4.95 2.375 4.50 0.2 4.75 15.18 15.18 12.80 12.80 -
L407AT 20.15 20.38 2.625 5.00 0.17 5.25 6.625 47.77 4.95 2.375 4.50 0.2 4.75 15.18 15.18 12.80 12.80 -
409AT 20.15 20.38 2.625 5.00 0.17 5.25 6.625 48.87 4.95 2.375 4.50 0.2 4.75 19.68 19.68 17.30 17.30 -
L409AT 20.15 20.38 2.625 5.00 0.17 5.25 6.625 52.27 4.95 2.375 4.50 0.2 4.75 19.68 19.68 17.30 17.30 -
504AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 50.99 5.95 2.875 5.50 0.2 5.75 - 13.26 10.88 10.88 -
L504AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 52.75 5.95 2.875 5.50 0.2 5.75 - - - 11.16 -
506AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 54.99 5.95 2.875 5.50 0.2 5.75 - 17.26 14.88 14.88 -
L506AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 56.75 5.95 2.875 5.50 0.2 5.75 - - - 15.16 -
508AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 59.99 5.95 2.875 5.50 0.2 5.75 - 22.26 19.88 19.88 -
L508AT 25.15 25.38 3.250 6.25 0.17 6.50 8.500 61.75 5.95 2.875 5.50 0.2 5.75 - - - 20.16 -
5010AY 25.17 25.38 4.125 8.00 0.17 8.25 8.500 71.49 6.70 3.250 6.25 0.2 6.50 - 31.26 28.88 28.88 -
* Dripproof, fully guarded machines can be used for wall or ceiling mounting. Assembly modifications must be made to maintain proper enclosure.
1. Splashproof machines will have additional covers, increasing the overall width at the commutator-end and drive-end side cover openings.
2. Dimension “D” will not be exceeded. When exact dimension is required, shims up tp .006 inch may be necessary.
3. Shaft diameters 1.50" and smaller will come within the limits of +0.0000 inch -0.0005 inch. Diameters larger than 1.5" will come within the limits of +0.0000 inch -0.0010 inch.
4. “V” represents minimum length of shaft available for hubs.

The standard single shaft machine has the commutator-end bearing bracket and shaft prepared to accept accessories. For additional information see 36C697103AA. Commutator-end
shaft extension is furnished only when specifically ordered, and is prepared for accessory drive. Conduit box will be assembled on the right hand side facing the commutator-end for
motors and on the left hand side facing commutator-end for generators. Conduit box will be assembled on opposite side of frame if so specified. Conduit box may be turned so that
entrance may be made upward, downward from commutator-end or drive-end. Dimensions pertaining to conduit boxes vary according to rating.
For shipping weight add 15% to net weight.
 DC Motors – Kinamatic™

Motor Dimensions cont.

Type CD, Totally Enclosed Fan Cooled
Frames 365AT to L409AT with Feet COMMUTATOR END
FC COMMUTATOR END
XP
C FC
P For Fig. 2 C
AB For Fig. 1
FW
0.93" SHAFT COVER FOR ACCESSORY MOUNTING FACE
AC SHAFT COVER FOR COMMUTATOR
FW FV AIR N-W
COMMUTATOR END EXTENSION OUTLET
END EXTENSION V
XN
FU
FU FV
O
XO
XL
D AE AIR AIR AF
INLET INLET N U
0.51" AD
0.51" AD W
G J HOLE(S) FOR K approx
H HOLE E AA CONDUIT SHAFT COVER FN-FW
FN-FW BS
2E NO COMMUTATOR
END EXTENSION FN 2E BA
A
B

Approx Commutator End

Drive End Key Dimmensions in Inches
Approx Wk2 of Key
See Fig Net Wt. Arm Lengt Length
Frames No. (lbs) Lb. Ft.2 Width Thick h ±.03 Width Thick ±.03 A Max B Max C D1 E 2F G H J K N
365AT 1 830 15.61 0.625 0.625 3.5 0.500 0.500 3.0 17.92 14.16 38.22 9.0 7.0 12.25 0.74 0.8125 3.26 2.31 4.92
366AT 1 940 18.27 0.625 0.625 3.5 0.500 0.500 3.0 17.92 15.90 40.42 9.0 7.0 14.00 0.74 0.8125 3.26 2.31 4.92
368AT 1 1100 22.21 0.625 0.625 3.5 0.500 0.500 3.0 17.92 19.90 43.42 9.0 7.0 18.00 0.74 0.8125 3.26 2.31 4.92
407AT 2 1380 35.47 0.625 0.625 4.0 0.625 0.625 3.5 20.00 20.16 44.90 10.0 8.0 18.00 0.86 0.9375 4.00 2.38 5.42
L407AT 2 1430 35.54 0.625 0.625 4.0 0.625 0.625 3.5 20.00 20.16 48.30 10.0 8.0 18.00 0.86 0.9375 4.00 2.38 5.42
7.22 409AT 2 1680 43.81 0.625 0.625 4.0 0.625 0.625 3.5 20.00 24.16 49.40 10.0 8.0 22.00 0.86 0.9375 4.00 2.38 5.42
L409AT 2 1730 43.88 0.625 0.625 4.0 0.625 0.625 3.5 20.00 24.16 52.80 10.0 8.0 22.00 0.86 0.9375 4.00 2.38 5.42
Dimensions continued (For Conduit Box Dimensions, refer to publication GEP-387K, Page 124) BS
DC Motors – Kinamatic™

Frame See Fig AA= AA= AA= AA=

Size No. O P U2 V3 W N-W BA FC FN FU2 FV3 FW FN-FW XO XP 3" 4" (2) 4" Blank
365AT 1 17.91 17.90 2.375 4.5 0.17 4.75 5.875 42.47 5.42 2.125 4.0 1.17 4.25 18.62 19.24 9.02 9.02 6.64 -
366AT 1 17.91 17.90 2.375 4.5 0.17 4.75 5.875 44.67 5.42 2.125 4.0 1.17 4.25 18.62 19.24 11.22 11.22 8.84 -
368AT 1 17.91 17.90 2.375 4.5 0.17 4.75 5.875 47.67 5.42 2.125 4.0 1.17 4.25 18.62 19.24 14.22 14.22 11.84 -
407AT 2 20.15 20.38 2.625 5.0 0.17 5.25 6.625 49.39 5.42 2.375 4.5 0.67 4.75 19.62 19.24 15.18 15.18 12.80 12.8
L407AT 2 20.15 20.38 2.625 5.0 0.17 5.25 6.625 52.79 5.42 2.375 4.5 0.67 4.75 19.62 19.24 15.18 15.18 12.80 12.8
409AT 2 20.15 20.38 2.625 5.0 0.17 5.25 6.625 53.89 5.42 2.375 4.5 0.67 4.75 19.62 19.24 19.68 19.68 17.30 17.3
L409AT 2 20.15 20.38 2.625 5.0 0.17 5.25 6.625 57.29 5.42 2.375 4.5 0.67 4.75 19.62 19.24 19.68 19.68 17.30 17.3

13.38 X 13.31
AA = Blank, Available Drill Space
Frame AB AE AF XL XN
360AT Not Available
400AT 24.76 12.95 6.75 13.5 13.5

Dimensions in Inches
AA = 3 AA = 4 AA= (2) 4
Frame AB AC AE AF XL XN AB AC AE AF XL XN AB AC AD AE AF XL XN
360AT 16.08 12.33 9.00 6.44 10.12 7 17.82 13.2 9.00 8.5 13.5 8.62 18.72 14.97 3 9.00 6.75 13.5 13.5
400AT 17.47 13.72 12.92 6.44 10.12 7 19.22 14.6 12.95 8.5 13.5 8.62 20.12 16.37 3 12.95 6.75 13.5 13.5
Machine can be used for wall or ceiling mounting.

1. Dimension "D" will not be exceeded. When exact dimension is required, shims up to .06 may be necessary.
2. Shaft diameters come within the limits of +0.0000 inch -0.0010 inch. Runout of shaft diameters shall not exceed 0.003 inch total indicator reading.
3. "V" represents minimum length of shaft available for hubs.
Commutator-end shaft extension is furnished only when specifically ordered, and is prepared for accessory drive.
When commutator-end shaft extension is not furnished, shaft and fan shroud on commutator-end is prepared for shaft driven accessories. Refer to 36C697103AA for dimensions.
Conduit box will be assembled on the right hand side facing the commutator-end for motors and on the left hand side facing commutator-end for generators. Conduit box will be
assembled on opposite side of frame if so specified. Conduit box may be turned so that entrance may be made upward, downward from commutator-end or drive-end. Dimensions
pertaining to conduit boxes vary according to rating.
For shipping weight add 15% to net weight.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 DC Motors – Kinamatic™

Kits and Accessories

K-3 Series
Tachometer Mounting Kits
PY Tachometer Mounting Kit
Catalog No. When used List Price Multiplier Symbol
A565 less Tach $370 GO-2SK3

Servo Tex® Tachometer Mounting Kit

Catalog No. When used List Price Multiplier Symbol
A569 with Tach (7.0V/1000 RPM) $973 GO-2SK3

Type CD
Blower Kits
Blower kits are designed for standard mounting on the motor commutator end and for addition only to Dripproof Fully Guarded (DPFG) or
Dripproof Fully Guarded - Separately Ventilated (DPFG-BV) motors. Blower motors are 230/460 Volts AC, 3 phase, 60 Hertz. To properly
mount blower kits on CD180AT frames, drilling and tapping three holes is required. For other applications, refer to factory.

Blower with Filter 7.23

Catalog No. Frame Size List Price Price Symbol

DC Motors – Kinamatic™ Kits

A688 CD218AT-CD2110AT $1,342 GO-2KITS
A689 CD258AT-CD259AT $1,250 GO-2KITS
A690 CD287AT-CD288AT $1,530 GO-2KITS
A691 CD327AT-CD328AT $1,805 GO-2KITS
A692 CD365AT-CD368AT $1,504 GO-2KITS
A693 CD407AT-CD409AT $1,517 GO-2KITS
A695 CD504AT-CD5010AY $3,024 GO-2KITS
A687 CDL182AT-CD188AT $1,337 GO-2KITS
A694 CDL407AT-CDL409AT $1,815 GO-2KITS

C-Face Endshield Kits

C-Face endshield kits are designed for mounting on the Fully Guarded or Totally Enclosed Non-Ventilated motors, but requires machine
disassembly by a qualified service facility.

Catalog No Frame Size List Price Price Symbol

A671 CD218AT-CD2110AT $425 GO-2KITS
A672 CD258AT-CD259AT $492 GO-2KITS
A674 CD287AT-CD288AT $730 GO-2KITS
A676 CD327AT-CD328AT $621 GO-2KITS
A670 CDL182AT-CD188AT (DP) $189 GO-2KITS

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 DC Motors – Kinamatic™

Kits and Accessories cont.

Lexon Covers
Two transparent covers are required to replace metal covers on the brush openings at the commutator. Each kit includes one cover.

Catalog No. Frame Size List Price Price Symbol

A677 CD218AT-CD2110AT $202 GO-2KITS
A678 CD258AT-CD259AT $219 GO-2KITS
A680 CD287AT-CD288AT $269 GO-2KITS
A682 CD327AT-CD328AT $336 GO-2KITS
A683 CD365AT-CD368AT $353 GO-2KITS
A683 CD407AT-CD409AT $353 GO-2KITS
A685 CD504AT-CD5010AY $386 GO-2KITS
A684 CDL407AT-CDL409AT $353 GO-2KITS

Tachometers
The Type AN enclosure provides a compact construction for medium accuracy speed-indicating or speed-regulating application. The AN series tachometers can be
furnished with either AC or digital output signal for speed regulation. For information on Type PY or Type BC tachometers, refer to the Tachometer Generator Section.

AN Series
Catalog No. Frame Size List Price Price Symbol
A647 CD182AT-CD328AT $2,382 GO-2KITS
A648 CD365AT-CD368AT $1,820 GO-2KITS
7.24 A649 CD407AT-CD409AT $2,604 GO-2KITS
A650 CD504AT-CD5010AY $2,604 GO-2KITS
DC Motors – Kinamatic™ Kits

Tachometer Mounting Kits

Tachometer mounting kits are design for mounting on the accessory commutator end shaft extension of Fully Guarded or Totally Enclosed Kinamatic motors, with
the exception of TEFC machines. Refer to factory for TEFC motors. This feature is optional on all CD180at frames. An accessory commutator end shaft extension is
supplied on all CD210at-CD500AT frame motors and will accept a tachometer kit only if the shaft extension is currently not is use. Note: Type BC and Type PY
tachometer must be ordered independently of the tachometer mounting kit.

Type BC Tachometer Mounting Kit

Catalog No. Frame Size List Price Price Symbol
A641 CD182AT-CD328AT $1,097 GO-2KITS
A642 CD365AT-CD368AT $978 GO-2KITS
A643 CD407AT-CD5010AY $1,008 GO-2KITS

Type PY Tachometer Mounting Kit

Catalog No. Frame Size List Price Price Symbol
A644 CD182AT-CD328AT $1,204 GO-2KITS
A645 CD365AT-CD368AT $1,303 GO-2KITS
A646 CD407AT-CD409AT $1,303 GO-2KITS
A686 CD504AT-CD5010AY $1,260 GO-2KITS

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Mill Duty DC Motors – MD800

Standard Features

Introduction
Auxiliary mill motors are specifically designed for mill, crane and hoist service. They may be used advantageously for any application which requires
a high ratio of peak to average load torques or where a motor is required to accelerate, decelerate or reverse rapidly under conditions of severe
duty-cycle operation. Armored motors are designed to meet the standards established by the Association of Iron and Steel Technology (AIST)

HP Range 5-250
Frame Size MD802 through MD818
Enclosures Totally Enclosed and Forced Ventilated
Speed Various
Voltage 230 Volt DC
Winding Series, Shunt, and Compound
Time Ratings Continuous, 30 min or 60 min
Frames Horizontally split steel frame w/ lifting lugs
Shaft Tapered and equal on DE and CE and replaceable without disturbing the windings
Ambient 40°C
Altitude 3300 ft 7.25
Insulation Class H
Temperature Rise 75 C rise by thermometer or 110 C rise by resistance
Bearing Type Single-width solid cylindrical roller bearing

DC Motors – MD800
Leads Exit frame F2 configuration (conduit box not standard)

Standard Type Product Offering

60 min, 75C Rise Totally Enclosed,
or Continuous, 75 C Rise 30 min 75C Rise Continuous Duty Cycle, 30% Time On,
Force-Ventilated Totally Enclosed 75C Rise, Totally Enclosed

Full-Load Speed, Full Load Speed

RPM (Approx.) RPM (Approx.) Full Load Speed RPM (Approx.)
Series Compound Shunt
Compound Adjustable
Frame HP Series or Shunt Speed HP Series Compound HP RPM HP RPM HP RPM
802A 5 900 1025 1025/2050 6.5 750 925 5.5 840 5 1080 5 1130
802B 7.5 800 900 900/1800 10 675 775 8 780 7.5 950 7.5 1000
802C 10 800 900 900/1800 13.5 675 775 10 800 9.5 940 9 1000
803 15 725 800 800/2000 19 620 725 15 725 14.5 840 14 880
804 20 650 725 725/1800 26 580 650 20 650 18.5 775 17 800
806 30 575 650 650/1950 39 500 600 30 575 28.5 690 25 715
808 50 525 575 575/1725 65 450 525 40 570 37.5 625 35 630
810 70 500 550 550/1650 90 440 500 60 550 52.5 615 45 600
812 100 475 515 515/1300 135 420 475 85 510 75 580 60 565
814 150 460 500 500/1250 200 400 460 115 515 110 565 85 560
816 200 450 480 480/1200 265 400 450 150 500 140 540 110 535
818 250 410 435 435/1100 325 360 400 185 485 165 490 130 470
More ratings and features are available.
For more information contact your local GE representative or call 1-800-541-7191

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Mill Duty DC Motors – MD800

Dimensions

7.26
DC Motors – MD800

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Appliance Motor
Standard Features

81mm Shaded Pole PSC 92mm Shaded Pole

HP range (watts) 1-35 2.3-16 16-50
Poles 4 4 4
Voltage <277vac <277vac <277vac
Efficiency 20+ 39+ 30+
Frequency 50,60,60/50 50,60,60/50 50,60,60/50
Agency Approvals UL, CSA UL, cURus UL, CSA
Alternate Mounting Single side pad Single side pad Tapped holes for shaft end
mounting
Ambient -20C to 70C -20C to 70C -20C to 70C
Base Mounting Std 3 tapped hole Std 3 tapped hole Resilient rings
Bearing Type Sleeve Sleeve Sleeve
Insulation B B B
Leads 26" Bare Wire Stripped 26" Bare Wire Stripped 12" ripcord leads
Motor Casing Aluminum Cast Iron Aluminum
Cast Iron Cast Iron
Protection Impedance or Overload Impedance or Overload Overload
Rotor Cast Aluminum Cast Aluminum Cast Aluminum
Shaft 1/4-20 threaded 1/4-20 threaded 1/4-20 threaded

8.1

Definite Purpose

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Appliance - Unit Bearing, GE 92mm
Pricing
GE 92mm, Shaded Pole - Open
Cat List Price
HP RPM Speeds Volts Base Rotation FLA No. Price Symbol Norm Stk Wt (lbs) Mfg. DIM C Dim (in) Notes
35M 1550 1 115 RR CCW 1.70 1441 $137 G3-1CON Y 7 AE4 6.40 4
35M 1550 1 115 RR CW 1.70 1431 $137 G3-1CON Y 6 AE4 6.40 4
35M 1550 1 208-230 RR CCW 0.87 1442 $140 G3-1CON N 9 AE4 6.40 4
35M 1550 1 208-230 RR CW 0.80 1432 $140 G3-1CON Y 7 AE4 6.40 4
1/20 1550 1 115 RR CCW 2.20 1341 $156 G3-1CON Y 9 AE8 7.10 4,93
1/20 1550 1 115 RR CW 2.20 1331 $156 G3-1CON Y 7 AE8 7.10 4,93
1/20 1550 1 230 RR CW 1.10 1336 $94 G3-1CON Y 9 AE8 6.80 4
1/20 1550 1 208-230 RR CCW 1.10 1342 $159 G3-1CON Y 7 AE8 7.10 4,93
1/20 1550 1 208-230 RR CW 1.10 1332 $159 G3-1CON Y 7 AE10 7.10 4,93
1/15 1550 1 208-230 RR CW 1.20 1232 $167 G3-1CON Y 7 AE8 7.10 4,84
Notes
4 Sleeve Bearing
84 Designed for 50 or 60 Hz operation
93 34" Motor leads

8.2
Definite Purpose

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Appliance - Unit Bearing, GE 81mm
Pricing
GE 81mm, Shaded Pole - Totally Enclosed - Aluminum Frame
Cat List Price Norm Wt Mfg C Dim
HP RPM Speeds Volts Base Rotation FLA No. Price Symbol Stk (lbs) Dim (in) Notes
2W 1550 1 115 Tap CW 0.25 5109 $22 G3-1CON Y 4 AC1 3.30 4,84
2W 1550 1 115 Tap CW 0.14 5108 $27 G3-1CON Y 2 AC1 3.30 4,84
2.5W 1000 1 115 Tap CW 0.30 5113 $28 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 115 Tap CCW 0.30 5214 $25 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 115 Tap CW 0.30 5213 $25 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 230 Tap CCW 0.20 5224 $27 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 230 Tap CW 0.20 5223 $27 G3-1CON Y 2 AC1 3.30 4,84
6W 1550 1 115 Tap CCW 0.40 5314 $27 G3-1CON Y 2 AC2 3.80 4,84
6W 1550 1 115 Tap CW 0.40 5313 $27 G3-1CON Y 2 AC2 3.80 4,84
9W 1550 1 115 Tap CCW 0.60 5414 $28 G3-1CON Y 2 AC2 3.80 4,84
9W 1550 1 115 Tap CW 0.60 5413 $28 G3-1CON Y 2 AC2 3.80 4,84
9W 1550 1 230 Tap CCW 0.30 5424 $30 G3-1CON Y 2 AC2 3.80 4,84
9W 1550 1 230 Tap CW 0.30 5423 $30 G3-1CON Y 2 AC2 3.80 4,84
16W 1550 1 115 Tap CCW 1.00 5814 $36 G3-1CON Y 3 AC3 4.00 4,84
16W 1550 1 115 Tap CW 1.00 5813 $36 G3-1CON Y 3 AC3 4.00 4,84
16W 1550 1 230 Tap CCW 0.50 5824 $38 G3-1CON Y 3 AC3 4.00 4,84
16W 1550 1 230 Tap CW 0.50 5823 $38 G3-1CON Y 3 AC3 4.00 4,84

Shaded Pole - Totally Enclosed - Cast Iron Frame

Cat List Price Norm Wt Mfg C Dim
HP RPM Speeds Volts Base Rotation FLA No. Price Symbol Stk (lbs) Dim (in) Notes
2.5W 1000 1 115 Tap CW 0.3 5111 $30 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 115 Tap CCW 0.3 5212 $28 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 115 Tap CW 0.3 5211 $28 G3-1CON Y 2 AC1 3.30 4,84
4W 1550 1 230 Tap CCW 0.2 5222 $30 G3-1CON Y 3 AC1 3.30 4,84
4W 1550 1 230 Tap CW 0.2 5221 $30 G3-1CON Y 3 AC1 3.30 4,84
6W 1550 1 115 Tap CCW 0.4 5312 $30 G3-1CON Y 4 AC2 3.80 4,84
6W 1550 1 115 Tap CW 0.4 5311 $30 G3-1CON Y 3 AC2 3.80 4,84
9W 1550 1 115 Tap CCW 0.6 5412 $31 G3-1CON Y 3 AC2 3.80 4,84
9W 1550 1 115 Tap CW 0.6 5411 $31 G3-1CON Y 3 AC2 3.80 4,84
9W 1550 1 230 Tap CCW 0.3 5422 $33 G3-1CON Y 3 AC2 3.80 4,84
9W 1550 1 230 Tap CW 0.3 5421 $33 G3-1CON Y 3 AC2 3.80 4,84
16W 1550 1 115 Tap CCW 1.0 5812 $42 G3-1CON Y 4 AC3 4.00 4,84 8.3
16W 1550 1 115 Tap CW 1.0 5811 $42 G3-1CON Y 4 AC3 4.00 4,84
16W 1550 1 230 Tap CCW 0.5 5822 $44 G3-1CON Y 6 AC3 4.00 4,84
16W 1550 1 230 Tap CW 0.5 5821 $44 G3-1CON Y 4 AC3 4.00 4,84

Definite Purpose
81mm - Permanent Split Capacitor
List Price Norm Wt Mfg C Dim
HP RPM Speed Volts Base Rotation FLA Cat No. Price Symbol Stk (lbs) Dim (in) Notes
5W 1550 1 115 Tap CW 0.2 5315 $34 G3-1CON Y 2 AC4 3.15 1,4,48
5W 1550 1 230 Tap CW 0.1 5325 $36 G3-1CON Y 2 AC4 3.15 1,4,48
5W 1550 1 115 Tap CCW 0.2 5335 $34 G3-1CON Y 2 AC4 3.15 1,4,48
5W 1550 1 230 Tap CCW 0.1 5345 $36 G3-1CON Y 2 AC4 3.15 1,4,48
9W 1550 1 115 Tap CW 0.3 5415 $40 G3-1CON Y 3 AC5 3.82 1,4,48
9W 1550 1 230 Tap CW 0.2 5425 $42 G3-1CON Y 3 AC5 3.82 1,4,48
9W 1550 1 115 Tap CCW 0.3 5435 $40 G3-1CON Y 3 AC5 3.82 1,4,48
9W 1550 1 230 Tap CCW 0.2 5445 $42 G3-1CON Y 3 AC5 3.82 1,4,48
16W 1550 1 115 Tap CW 0.6 5815 $45 G3-1CON Y 4 AC6 3.98 1,4,48
16W 1550 1 230 Tap CW 0.3 5825 $47 G3-1CON Y 4 AC6 3.98 1,4,48
16W 1550 1 115 Tap CCW 0.6 5835 $45 G3-1CON Y 4 AC6 3.98 1,4,48
16W 1550 1 230 Tap CCW 0.3 5845 $47 G3-1CON Y 4 AC6 3.98 1,4,48
Notes
1 Internally mounted Capacitor
4 Sleeve Bearing
84 Designed for 50 or 60 Hertz Operation

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Appliance - Unit Bearing, GE 81mm and GE 92mm
Dimensions

81mm
For Continuous air-over applications; mounting holes #8-36 tap.
Dimension in Inches
Dim. Ref. B C Shaft1
1 2.80 3.30 Threads
2 3.30 3.80 Threads
3 3.50 4.00 Threads
4 2.74 3.15 Threads
5 3.31 3.82 Threads
6 3.71 3.98 Threads
1. Threaded shaft is 1/4-20, 0.51/0.41 long.

92mm
Motor for Continuous air-over applications; lead-end mounting, 4 holes
#8-32 NC-2B tap on 2.84" bolt circle; resilient-ring diameter 1.75"
Dimensions in Inches
Dim. Ref. B C YO Dia. Max.
1 4.50 5.81 2
3.94
2 4.75 6.06 2
3.94
3 4.82 6.13 4.51 3.94
4 5.07 6.38 4.76 3.94
5 5.58 6.91 2
4.20
6 6.15 7.48 5.83 4.20
7 5.90 7.23 5.58 4.20
8 5.07 7.13 4.76 3.94
9 5.85 7.16 2
4.20
8.4 10 4.76 6.81 2
3.94
2. Motor does not have resilient rings.
Definite Purpose

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Farm Duty
Pricing

High Torque - Capacitor Start - Totally Enclosed Fan Cooled

Cat List Price Wt C Dim
HP RPM Volts Frame SF PROT Base FLA No. Price Symbol Norm Stk (lbs) (in) Notes
2 1800 230 182TZ 1.15 Man WB 11.0 F787 $476 G4-7FAZ N 79 17.01 CI
3 1800 230 184TZ 1.15 Man WB 15.5 F789 $518 G4-7FAZ N 95 18.26 CI
5 1800 230 184TZ 1.15 Man WB 22.0 F792 $601 G4-7FAZ Y 103 18.70 CI

Extra High Torque - Capacitor Start - Totally Enclosed Fan Cooled

Cat List Price Wt C Dim
HP RPM Volts Frame SF PROT Base FLA No. Price Symbol Norm Stk (lbs) (in) Notes
1 1800 115/230 143T 1.00 Man Ftd 14.0/7.0 F835 $350 G4-7FAZ N 48 15.80 CI
1 1800 115/230 143T 1.00 Man Ftd 14.0/7.0 F837 $267 G4-7FAZ N 42 15.05 CI
1.5 1800 115/230 145T 1.00 Man Ftd 22.0/11.0 F836 $365 G4-7FAZ N 65 15.80 CI
2 1800 230 182TZ 1.15 Man Ftd 14.0 F786 $495 G4-7FAZ N 77 17.01 15,CI
3 1800 230 184TZ 1.15 Man Ftd 21.0 F788 $561 G4-7FAZ N 92 18.26 16,CI
5 1800 230 215TZ 1.15 Man Ftd 22.6 F791 $765 G4-7FAZ N 143 21.60 14,CI
5 1800 230 184TZ 1.15 Man Ftd 30.0 F790 $665 G4-7FAZ N 103 18.70 12,CI
7.5 1800 230 215TZ 1.15 Man Ftd 36.0 F793 $1,000 G4-7FAZ Y 178 21.60 14,CI
7.5 1800 230 215TZ 1.15 Man Ftd 36.0 F798 $1,000 G4-7FAZ N 178 21.97 CI
10 1800 230 215TZ 1.00 Man Ftd 48.0 F795 $1,200 G4-7FAZ N 183 21.97 13,CI
10 1800 230 215TZ 1.00 Man Ftd 48.0 F794 $1,200 G4-7FAZ Y 183 21.60 14,CI

Notes
CI Cast Iron
12 Shaft extension 3 7/16" long by 1 1/8" diameter
13 Shaft extension 3 5/8" long by 1 3/8" diameter
14 Shaft extension 3 1/4" long by 1 1/8" diameter
15 Shaft extension 2 3/4" long by 7/8" diameter
16 Shaft extension 3" long by 1 1/8" diameter

Dimensions
8.5

Definite Purpose

Frame Key Length N-W V U E 2F A B BA AC D G J O P

143 1.38 1.88 - 6.25 2.44 3.00 6.28 5.00 2.75 4.53 3.50 0.16 1.53 7.13 7.26
145 1.38 2.25 2.2 - 2.75 5.00 6.70 5.90 2.25 4.92 3.50 0.35 - 7.45 7.87
182 1.78 2.75 2.7 1.125 3.75 4.50 8.80 5.90 2.75 5.99 4.50 0.65 1.75 9.20 9.40
184 2.00 3.00 2.7 1.125 3.75 5.50 8.80 6.90 2.75 5.99 4.50 0.65 1.75 9.20 9.40
215 1.50 3.25 3.17 1.125 4.25 7.00 9.85 8.35 3.50 7.75 5.25 0.70 1.75 10.63 10.75
All dimensions in inches.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Electric Vehicle - OEM Replacement
Pricing

10 Tooth Female Spline/Graziano and Kawasaki Axles (Club Car)

Torque Cat List Price Norm Wt C Dim
HP RPM Volts (oz-ft) Duty PROT Base FLA No. Price Symbol Stk (lbs) (in) Notes
3 2300 36 60.0 60 Min None FLG 75.0 D375 $465 GO-1GLF N 38 9.15
3.1 2190 48 60.0 60 Min None FLG 56.0 D376 $465 GO-1GLF N 50 10.55
3.5 3000 36 98.0 5 Min None FLG 90.0 D377 $511 GO-1GLF Y 38 9.15
3.5 3340 48 78.0 5 Min None FLG 58.7A/7.6F D391 $680 GO-1GLF Y 35 8.70 120
3.5 3775 48 78.0 5 Min None FLG 65.0A/5.0F D390 $680 GO-1GLF Y 35 8.70 120
3.75 3250 48 100.0 30 Min None FLG 69.0 D378 $511 GO-1GLF Y 38 9.45
4 4150 48 81.0 Cont None FLG 72.0 D379 $738 GO-1GLF N 50 10.72
4/5.5 4150/5700 36/48 81.0 Cont None FLG 105.0/105.0 D380 $919 GO-1GLF Y 60 11.12
5 2740 48 113.0 30 Min None FLG 89.0A/7.6F D388 $840 GO-1GLF Y 55 10.10 120
6.1 4600 36 112.0 60 Min None FLG 155.0 D392 $780 GO-1GLF Y 49 9.20
11.4 2280 48 150.0 5 Min None FLG 228.0 D395 $880 GO-1GLF Y 55 10.10

19 Tooth Female Spline/Dana H12 Axles (EZ-Go, Yahama, Columbia Par Car, and Melex)
Torque Cat List Price Norm Wt C Dim
HP RPM Volts (oz-ft) Duty PROT Base FLA No. Price Symbol Stk (lbs) (in) Notes
1.86 3300 36 47.4 30 Min None FLG 62.00 D381 $465 GO-1GLF N 38 8.44
2 2800 36 60.0 60 Min None FLG 50.00 D294 $475 GO-1GLF Y 38 8.44
2.5 3300 36 63.7 60 Min None FLG 72.00 D295 $510 GO-1GLF Y 43 9.20
2.5 3300 48 65.5 60 Min None FLG 47.00 D296 $510 GO-1GLF N 41 9.19
3.5 3000 36 98.0 5 Min None FLG 91.00 D382 $511 GO-1GLF Y 40 8.44
4 4400 36 76.4 30 Min None FLG 102.00 D297 $718 GO-1GLF Y 50 9.20
4 4400 48 76.4 60 Min None FLG 81.00 D298 $718 GO-1GLF N 43 9.20
4.3 3650 48 98.0 Cont None FLG 82.00A/10.00F D397 $800 GO-1GLF Y 54 10.20 120
4.3 3500 48 98.0 Cont None FLG 8.01A/14.20F D396 $800 GO-1GLF Y 53 10.20 120
6.1 5330 36 96.0 60 Min None FLG 157.00 D398 $760 GO-1GLF Y 45 9.60
8 1600 36 150.0 5 Min None FLG 226.00 D394 $880 GO-1GLF Y 55 10.20

8.6

Cushman Replacements
Torque Cat List Price Norm Wt C Dim
HP RPM Volts (oz-ft) Duty PROT Base FLA No. Price Symbol Stk (lbs) (in) Notes
Definite Purpose

4/3 4000/3000 48/36 84 60 Min None FLG 82.0/82.0 D384 $987 GO-1GLF Y 60 10.96 57
2/1.5 2800/1600 36/24 30 60 Min None FLG 50.0/59.0 D383 $579 GO-1GLF N 35 8.44

Taylor Dunn Replacements

Torque Cat List Price Norm Wt C Dim
HP RPM Volts (oz-ft) Duty PROT Base FLA No. Price Symbol Stk (lbs) (in) Notes
2/1.5 2800/1600 36/24 60 60 Min None FLG 50.0/59.0 D386 $579 GO-1GLF N 28 8.44 57
2/1.5 2800/1600 36/24 60 60 Min None SPL 50.0/59.0 D387 $590 GO-1GLF Y 40 11.90
10/3.5/2.2 1350/2900/1850 36/36/24 101.4 5/30/60 None SPL 320.0/95.0/95.0 D385 $964 GO-1GLF Y 62 13.05

Notes
57 Open construction
120 Shunt motors have armature and field amps shown, shunt motors have ODE mounted speed sensor.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Fork Truck / Scissor Lift Truck
Dimensions

Fork Truck AC Motors

S2-60 S3-20%
Frame Size RPM Length (in) Diameter (in)
HP Ft - lb HP Ft - lb
140 4100 5.0 6.4 7.5 9.6 13.9 6.3
180 2120 8.0 19.8 9.9 24.6 13.9 7.8
180 2120 6.3 15.6 8.4 20.8 13.1 7.8
180 2120 4.8 12.0 6.9 17.1 12.3 7.8
180 2120 3.5 8.7 5.4 13.4 11.5 7.8
210 2120 14.0 34.7 17.5 44.1 13.9 9.4
210 2120 11.2 27.7 14.9 37.1 13.1 9.4
210 2120 8.8 21.7 12.5 30.9 12.3 9.4
210 2120 6.5 15.8 10.0 24.6 11.5 9.4
250 1000 18.8 98.6 26.7 140.0 15.9 10.8
250 1000 17.1 89.7 23.0 121.0 15.1 10.8
250 1000 15.4 80.7 20.7 108.9 14.3 10.8
250 1000 13.6 71.7 18.4 96.7 13.5 10.8
250 1000 11.9 62.7 16.1 84.5 12.7 10.8

8.7

Definite Purpose

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Wash Down Duty
Pricing

Permanent Magnet DC - NEMA C-Face Mounting - Totally Enclosed

Price Wt C Dim
HP RPM Volts Frame SF PROT Base FLA Cat No. List Price Symbol Norm Stk (lbs) (in) Notes
1/4 1725 90 56C 1 None Bolt-On 3.0 D350 $ 354 GO-1PM N 19 10.42 55
1/4 1725 180 56C 1 None Bolt-On 1.4 D351 $ 354 GO-1PM N 19 10.42 55
1/3 1725 90 56C 1 None Bolt-On 3.5 D352 $ 372 GO-1PM N 25 11.42 55
1/3 1725 180 56C 1 None Bolt-On 1.8 D353 $ 372 GO-1PM N 25 11.42 55
1/2 1725 90 56C 1 None Bolt-On 5.5 D354 $ 420 GO-1PM Y 29 12.87
1/2 1725 180 56C 1 None Bolt-On 2.8 D355 $ 420 GO-1PM N 29 12.87
3/4 1725 90 56C 1 None Bolt-On 8.0 D356 $ 511 GO-1PM Y 42 14.87
3/4 1725 180 56C 1 None Bolt-On 4.0 D357 $ 511 GO-1PM N 39 14.87
1 1725 90 56C 1 None Bolt-On 9.5 D358 $ 634 GO-1PM Y 41 14.87
1 1725 180 56C 1 None Bolt-On 4.8 D359 $ 634 GO-1PM N 41 14.87
Notes
55 TENV construction

Dimensions

8.8
Definite Purpose

Frame C AG Key Length N YS N-W AH

56JA, 56HA 10.42 8.29 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56KA 11.42 9.29 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56KA 12.87 10.75 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
56 PA, 56SA 14.87 12.75 1.51 1.49 1.96 1.41 2.00 1.88 2.17 2.09
All dimensions in inches.

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Premium Efficient Explosion Proof
Standard Features

Div 1, Class I, Group C, D

Div 1, Class II, Group E, F, G
HP Rating 1.5-50
Poles 2,4,6,8
Voltage 230/460, 575
Efficiency Premium
Frequency 60 Hz
NEMA Design B
Agency Approvals NEMA MG1, Meets CSA-C390
Altitude Up to 3300ft at 40ºC
Ambient 40ºC
Balance/Vibration 0.15 in/sec
Bearing Caps Yes
Bearing Protection Shaft Slinger only Class II, Group E
Bearing Type Ball
Conduit Box Finned Cast Iron, ASTM A48, Class 25
Drains None
End Shield Finned Cast Iron, ASTM A48, Class 25
Fan Polypropylene Non-Sparking or Aluminum Alloy
Fan Cover Cast Iron - ASTM A48
Fasteners SAE Grade 5
Frame Material Finned Cast Iron, ASTM A48, Class 25
Frame Size 182T-326T
Grease Polyurea
Ground Inside Conduit Box
Insulation Class F
Insulation System Non-Hygroscopic, Anti-Fungus 8.9
L10 Bearing Life Direct Coupled: 65,000 hrs, Belted: 25,000 hrs
Lifting Means Lifting Lugs Cast Into Frame
Mounting F1

Definite Purpose
Mounting Holes Dual Mounting holes, Non-NEMA
Nameplate Stainless Steel AISI 202 or 302
Paint Epoxyester
Relubrication 1 Fitting and 1 Plug Each End
Rotor Cast Aluminum
Service Factor 1.0
Temperature Rise 105ºC Max (UL Limit), at rated load
Tests NEMA Routine
Time Rating Continuous
Warranty 24 months from date of purchase or 30 months from date of shipment, whichever occurs first

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Premium Efficient Explosion Proof
Pricing

Base Mounted-Class I, Group D; Class II, Groups F and G

Volts: 230/460, 575
HP: 1.5-50
NEMA Guar Cat List Price Norm Wt C Dim
HP RPM Volts Frame SF FLA Nom Eff Min Eff No. Price Symbol Stk (lbs) (in) Notes
1.5 1200 230/460 182T 1.15 4.8/2.4 87.5 86.5 E9601 $747 G6-7XP$ N 76 15.90
1.5 1200 575 182T 1.15 1.9 87.5 86.5 E9602 $747 G6-7XP$ N 76 15.90
2 1200 230/460 184T 1.15 6.4/3.2 86.5 85.5 E9603 $806 G6-7XP$ N 101 15.90
2 1200 575 184T 1.15 2.6 86.5 85.5 E9604 $806 G6-7XP$ N 101 15.90
3 3600 230/460 182T 1.15 8.0/4.0 87.5 86.5 E9605 $762 G6-7XP$ N 76 15.90
3 3600 575 182T 1.15 3.1 87.5 86.5 E9606 $762 G6-7XP$ N 76 15.90
3 1800 230/460 182T 1.15 7.8/3.9 89.5 88.5 E9607 $730 G6-7XP$ N 76 15.90
3 1800 575 182T 1.15 3.2 89.5 88.5 E9608 $730 G6-7XP$ N 76 15.90
3 1200 230/460 213T 1.15 8.8/4.4 89.5 88.5 E9678 $951 G6-7XP$ N 200 20.20
3 1200 575 213T 1.15 3.5 89.5 88.5 E9610 $951 G6-7XP$ N 200 20.20
5 3600 230/460 184T 1.15 14.4/7.2 87.5 86.5 E9611 $886 G6-7XP$ N 101 15.90
5 3600 575 184T 1.15 5.7 87.5 86.5 E9612 $886 G6-7XP$ N 101 15.90
5 1800 230/460 184T 1.15 13.2/6.6 88.5 87.5 E9613 $813 G6-7XP$ N 101 15.90
5 1800 575 184T 1.15 5.3 88.5 87.5 E9614 $813 G6-7XP$ N 101 15.90
5 1200 230/460 215T 1.15 14.4/7.2 89.5 88.5 E9679 $1,233 G6-7XP$ N 220 20.20
5 1200 575 215T 1.15 5.7 89.5 88.5 E9616 $1,233 G6-7XP$ N 220 20.20
7.5 3600 230/460 213T 1.15 17.2/8.6 90.2 89.5 E9661 $1,041 G6-7XP$ N 200 20.20
7.5 3600 575 213T 1.15 6.9 90.2 89.5 E9617 $1,041 G6-7XP$ N 200 20.20
7.5 1800 230/460 213T 1.15 18.0/9.0 91.0 90.2 E9669 $1,036 G6-7XP$ N 200 20.20
7.5 1800 575 213T 1.15 7.2 91.0 90.2 E9618 $1,036 G6-7XP$ N 200 20.20
7.5 1200 230/460 254T 1.15 20.2/10.1 91.0 90.2 E9680 $1,668 G6-7XP$ N 315 25.60
7.5 1200 575 254T 1.15 8.0 91.0 90.2 E9619 $1,668 G6-7XP$ N 315 25.60
10 3600 230/460 215T 1.15 22.4/11.2 91.0 90.2 E9662 $1,173 G6-7XP$ N 220 20.20
10 3600 575 215T 1.15 9.1 91.0 90.2 E9620 $1,173 G6-7XP$ N 220 20.20
10 1800 230/460 215T 1.15 24.0/12.0 91.0 90.2 E9671 $1,195 G6-7XP$ N 220 20.20
8.10
10 1800 575 215T 1.15 9.5 91.0 90.2 E9621 $1,195 G6-7XP$ N 220 20.20
10 1200 230/460 256T 1.15 26.2/13.1 91.0 90.2 E9686 $1,955 G6-7XP$ N 350 25.60
10 1200 575 256T 1.15 10.5 91.0 90.2 E9622 $1,955 G6-7XP$ N 350 25.60
Definite Purpose

15 3600 230/460 254T 1.15 35.2/17.6 91.7 91.0 E9663 $1,629 G6-7XP$ N 315 25.59
15 3600 575 254T 1.15 13.8 91.0 90.2 E9623 $1,629 G6-7XP$ N 315 25.60
15 1800 230/460 254T 1.15 36.6/18.3 92.4 91.7 E9672 $1,607 G6-7XP$ N 315 25.60
15 1800 575 254T 1.15 14.6 92.4 91.7 E9624 $1,607 G6-7XP$ N 315 25.60
15 1200 230/460 284T 1.15 36.8/18.4 91.0 90.2 E9682 $2,606 G6-7XP$ N 460 28.60
15 1200 575 284T 1.15 14.7 91.0 90.2 E9625 $2,606 G6-7XP$ N 460 28.60

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
Premium Efficient Explosion Proof
Pricing cont.

Base Mounted-Class I, Group D; Class II, Groups F and G

Volts: 230/460, 575
HP: 1.5-50
NEMA Guar Cat List Price Norm Wt C Dim
HP RPM Volts Frame SF FLA Nom Eff Min Eff No. Price Symbol Stk (lbs) (in) Notes
20 3600 230/460 256T 1.15 45.2/22.6 91.7 91.0 E9664 $1,928 G6-7XP$ N 350 25.60
20 3600 575 256T 1.15 18.1 91.7 91.0 E9626 $1,928 G6-7XP$ N 350 25.60
20 1800 230/460 256T 1.15 48.0/24.0 92.4 91.7 E9673 $1,910 G6-7XP$ N 350 25.60
20 1800 575 256T 1.15 19.2 92.4 91.7 E9627 $1,910 G6-7XP$ N 350 25.60
20 1200 230/460 286T 1.15 48.4/24.2 91.0 90.2 E9683 $3,064 G6-7XP$ N 510 28.60
20 1200 575 286T 1.15 19.4 91.0 90.2 E9628 $3,064 G6-7XP$ N 510 28.60
25 3600 230/460 284TS 1.15 55.6/27.8 92.4 91.7 E9665 $2,424 G6-7XP$ N 460 27.20
25 3600 575 284TS 1.15 22.4 92.4 91.7 E9629 $2,424 G6-7XP$ N 460 27.20
25 1800 230/460 284T 1.15 57.8/28.9 93.0 92.4 E9674 $2,338 G6-7XP$ N 460 28.60
25 1800 575 284T 1.15 23.1 93.0 92.4 E9630 $2,338 G6-7XP$ N 460 28.60
30 3600 230/460 286TS 1.15 67.2/33.6 92.4 91.7 E9666 $2,745 G6-7XP$ N 510 27.20
30 3600 575 286TS 1.15 26.9 92.4 91.7 E9631 $2,745 G6-7XP$ N 510 27.20
30 1800 230/460 286T 1.15 69.4/34.7 93.0 92.4 E9675 $2,635 G6-7XP$ N 510 28.60
30 1800 575 286T 1.15 27.8 93.0 92.4 E9632 $2,635 G6-7XP$ N 510 28.60
30 1200 230/460 326T 1.15 73.6/36.8 92.4 91.7 E9685 $4,361 G6-7XP$ N 730 32.00
40 1800 230/460 324T 1.15 98.8/49.4 94.1 93.6 E9676 $3,618 G6-7XP$ N 730 32.00
50 1800 230/460 326T 1.15 124.4/62.2 94.1 93.6 E9677 $4,262 G6-7XP$ N 740 32.00

8.11

Definite Purpose

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
Premium Efficient Explosion Proof
Dimensions

Cast Iron Construction/Frames 143-326, Type KS, 3-Phase/Dimensions – For Estimating Only
Dimensions in Inches
Approx.
Net Shaft Mounting (18)

Weight Key
Frame in lbs Width Depth Length N-W U(1) V E H BA BS 2F 2XF A B C D(3) G J K L O
143T 43 0.187 0.187 1.380 2.25 0.875 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
145T 50 0.187 0.187 1.380 2.25 0.875 2.12 2.75 0.39 2.25 2.25 5.00 4.00 6.88 5.88 13.42 3.50 0.40 1.39 2.32 6.42 7.25
182T 76 0.250 0.250 1.750 2.75 1.125 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
184T 101 0.250 0.250 1.750 2.75 1.125 2.50 3.75 0.46 2.75 2.75 5.50 4.50 8.68 6.64 15.91 4.50 0.46 1.54 2.58 7.66 9.25
213T 200 0.312 0.312 2.380 3.38 1.375 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
215T 220 0.312 0.312 2.380 3.38 1.375 3.12 4.25 0.46 3.50 3.50 7.00 5.50 9.60 8.00 20.15 5.25 0.57 1.47 3.12 9.77 10.43
254T 315 0.375 0.375 2.380 4.00 1.625 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
256T 350 0.375 0.375 2.880 4.00 1.625 3.76 5.00 0.58 4.25 5.00 10.00 8.25 11.20 11.30 25.29 6.25 0.65 1.52 3.93 12.34 12.50
284TS 460 0.375 0.375 1.880 3.25 1.625 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
284T 460 0.500 0.500 3.250 4.62 1.875 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
286TS 510 3.750 3.750 1.880 3.25 1.625 3.00 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 27.20 7.00 0.76 1.75 4.12 13.70 13.88
286T 510 0.500 0.500 3.250 4.62 1.875 4.38 5.50 0.58 4.76 5.50 11.00 9.50 12.40 12.80 28.58 7.00 0.76 1.75 4.12 13.70 13.88
324TS 685 0.500 0.500 2.000 3.75 1.875 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
324T 685 0.500 0.500 3.880 5.25 2.125 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 32.04 8.00 0.99 2.01 3.62 15.54 17.07
326TS 800 0.500 0.500 2.000 3.75 1.875 3.50 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 30.54 8.00 0.99 2.01 3.62 15.54 17.07
326T 800 0.500 0.500 3.880 5.25 2.125 5.00 6.25 0.67 5.25 6.00 12.00 10.50 14.40 13.80 32.04 8.00 0.99 2.01 3.62 15.54 17.07
8.12 1. Shaft diameters 1 1/2 inches and smaller will come within the limits of +0.000 inch, -0.0005 inch diameters 1 5/8 inches and larger +0.000 inch, -0.001 inch
3. Tolerance on “D” dimension for rigid base motors will be +0.000 inch, -0.060 inch. No tolerance has been est. for the “D” dimension of resilient mounted motors.
18. Motor feet have 2 holes per foot allowing NEMA F-1 or F-2 assembly while maintaining critical NEMA mounting dimensions.
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward, or from either side.
Weights shown are approximate shipping weights and should be used for estimating only.
Definite Purpose

Conduit Box Dimensions

Nominal Approx. Dimensions in Inches
Frame HP Vol. AA* AB AC AF XL XN
143-145 2 32 0.75 6.62 5.12 2.50 4.30 5.40
182-184 5 32 0.75 7.82 6.32 2.50 4.30 5.40
213-215 10 55 1.00 9.50 7.42 3.50 5.78 4.16
254-256 20 140 1.25 11.68 9.12 4.59 7.37 5.37
284-286 30 140 1.50 12.44 9.88 4.59 7.37 5.37
324-326 50 346 3.00 16.13 12.43 6.44 10.14 7.00
* A tapped NPT hole is provided for the conduit size listed in Column AA

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Definite Purpose
X$D® Severe Duty
Pricing
Volts: 230/460, 460, 575
HP: 20-200
Totally Enclosed Fan Cooled-Severe Duty X$D – Base Mounted
Nom Cat List Price C Dim
HP RPM Volts Frame SF FLA Eff No. Price Symbol Norm Stk Wt (lbs) (in) Notes
20 900 460 324T 1.15 27.2 89.5 E9748 $4,136 G6-7S$ N 710 32.02 CI
25 1200 230/460 324T 1.15 61.4/30.7 92.4 E9158 $3,096 G6-7S$ N 710 32.02 CI
25 1200 460 324T 1.15 30.7 92.4 E9119 $3,096 G6-7S$ N 710 32.02 CI
25 1200 575 324T 1.15 24.6 92.4 E9758 $3,096 G6-7S$ N 710 32.02 CI
25 900 460 326T 1.15 34.2 89.5 E9761 $4,887 G6-7S$ N 730 32.02 CI
30 1200 230/460 326T 1.15 73.6/36.8 92.4 E9161 $3,566 G6-7S$ N 730 32.02 CI
30 1200 460 326T 1.15 36.8 92.4 E9122 $3,566 G6-7S$ N 730 32.02 CI
30 1200 575 326T 1.15 29.5 92.4 E9834 $3,566 G6-7S$ N 730 32.02 CI
30 900 460 365T 1.15 39.2 93.0 E9767 $5,788 G6-7S$ N 1020 34.50 CI
40 3600 230/460 324TS 1.15 98.2/49.1 93.6 E9162 $2,938 G6-7S$ N 650 30.50 CI
40 3600 460 324TS 1.15 49.1 93.6 E996 $2,938 G6-7S$ N 650 30.50 CI
40 3600 460 324T 1.15 49.1 93.6 E9820 $2,938 G6-7S$ N 650 32.02 CI
40 3600 575 324TS 1.15 39.3 93.6 E9829 $2,938 G6-7S$ N 650 30.50 CI
40 1800 230/460 324T 1.15 98.8/49.4 94.1 E9163 $2,823 G6-7S$ N 730 32.02 CI
40 1800 460 324T 1.15 49.1 94.1 E9915 $2,823 G6-7S$ N 730 32.02 CI
40 1800 460 324TS 1.15 49.4 94.1 E9916 $2,823 G6-7S$ N 730 30.50 CI
40 1800 575 324T 1.15 39.6 94.1 E9768 $2,823 G6-7S$ N 730 32.02 CI
40 1200 460 364T 1.15 46.5 93.6 E9124 $4,833 G6-7S$ N 1070 34.50 CI
40 1200 575 364T 1.15 37.2 93.6 E9835 $4,833 G6-7S$ N 1070 34.50 CI
40 900 460 365T 1.15 52.6 93.0 E9770 $7,145 G6-7S$ N 1050 34.50 CI
40 900 575 365T 1.15 42.4 92.4 E9534 $7,145 G6-7S$ N 1050 34.50 CI
50 3600 230/460 326TS 1.15 119.0/59.5 93.6 E9164 $3,814 G6-7S$ N 680 30.50 CI
50 3600 460 326T 1.15 59.5 93.6 E9823 $3,814 G6-7S$ N 680 32.02 CI
50 3600 460 326TS 1.15 59.5 93.6 E997 $3,814 G6-7S$ N 680 30.50 CI
50 3600 575 326TS 1.15 44.1 92.4 E9587 $4,577 G6-7S$ N 700 30.50 CI
50 3600 575 326TS 1.15 47.6 93.6 E9839 $3,814 G6-7S$ N 680 30.50 CI
50 1800 230/460 326T 1.15 124.4/62.2 94.1 E9165 $3,467 G6-7S$ N 740 32.02 CI
50 1800 460 326T 1.15 62.2 94.1 E9917 $3,467 G6-7S$ N 740 32.02 CI 8.13
50 1800 460 326TS 1.15 62.2 94.1 E9918 $3,467 G6-7S$ N 740 30.50 CI
50 1800 575 326T 1.15 49.4 94.1 E9765 $3,467 G6-7S$ N 740 32.02 CI
50 1200 460 365T 1.15 58.5 93.6 E9126 $5,549 G6-7S$ N 1050 34.50 CI

Definite Purpose
50 1200 460 365TS 1.15 58.5 93.6 E9127 $5,549 G6-7S$ N 1050 32.40 CI
50 1200 575 365T 1.15 46.8 93.6 E9775 $5,549 G6-7S$ N 1050 34.50 CI
50 900 460 404T 1.15 59.9 93.0 E9773 $8,595 G6-7S$ N 1500 39.40 CI
50 900 575 404T 1.15 47.9 93.0 E9535 $8,595 G6-7S$ N 1500 39.40 CI
60 3600 460 364TS 1.15 69.5 94.5 E998 $5,017 G6-7S$ N 1000 39.40 CI
60 3600 575 364TS 1.15 55.6 94.5 E9847 $5,017 G6-7S$ N 1000 39.40 CI
60 1800 460 354T 1.15 71.5 94.5 E9919 $4,974 G6-7S$ N 1060 34.50 CI
60 1800 460 364TS 1.15 71.5 94.5 E9921 $4,974 G6-7S$ N 1060 39.40 CI
60 1800 575 364T 1.15 58.0 94.5 E9776 $4,974 G6-7S$ N 1060 34.50 CI
60 1200 460 404T 1.15 68.2 94.1 E9128 $6,502 G6-7S$ N 1530 39.40 CI
60 1200 575 404T 1.15 54.3 94.1 E9837 $6,502 G6-7S$ N 1530 39.40 CI
60 900 460 405T 1.15 71.9 93.0 E9778 $9,934 G6-7S$ N 1530 39.40 CI
60 900 575 405T 1.15 57.5 93.0 E9536 $9,934 G6-7S$ N 1530 39.40 CI
Notes
CI Cast Iron

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
X$D® Severe Duty
Pricing cont.
Volts: 230/460, 460, 575
HP: 20-200
Totally Enclosed Fan Cooled-Severe Duty X$D – Base Mounted
Price C Dim
HP RPM Volts Frame SF FLA Nom Eff Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
75 3600 460 365TS 1.15 88.5 94.5 E999 $6,300 G6-7S$ N 990 39.40 CI
75 3600 575 365TS 1.15 70.8 94.5 E9830 $6,300 G6-7S$ N 990 39.40 CI
75 1800 460 365T 1.15 91.5 94.1 E9922 $6,305 G6-7S$ N 1070 34.50 CI
75 1800 460 365TS 1.15 91.5 94.1 E9923 $6,305 G6-7S$ N 1070 39.40 CI
75 1800 575 365T 1.15 72.9 94.5 E9781 $6,305 G6-7S$ N 1070 34.50 CI
75 1200 460 405T 1.15 87.2 94.1 E9131 $7,655 G6-7S$ N 1490 39.40 CI
75 1200 460 405T 1.15 88.2 93.6 S2333 $6,496 G6-7S$ N 1450 39.40 CI
75 1200 575 405T 1.15 69.8 94.1 E9868 $7,655 G6-7S$ N 1490 39.40 CI
75 1200 575 405T 1.15 71.0 93.6 S2174 $6,496 G6-7S$ N 1450 39.40 CI
75 900 460 444T 1.15 89.9 94.1 E9780 $13,230 G6-7S$ N 1930 45.30 CI
75 900 575 444T 1.15 71.9 94.1 E9537 $13,230 G6-7S$ N 1980 45.30 CI
100 3600 460 405TS 1.15 110.0 94.5 E9510 $8,442 G6-7S$ N 1480 36.40 CI
100 3600 575 405TS 1.15 88.1 94.5 E9831 $8,442 G6-7S$ N 1480 36.40 CI
100 1800 460 405T 1.15 115.0 95.0 E9924 $7,790 G6-7S$ N 1540 39.40 CI
100 1800 460 450TS 1.15 115.0 95.0 E9925 $7,790 G6-7S$ N 1540 36.40 CI
100 1800 575 450TS 1.15 91.7 95.0 E9779 $7,790 G6-7S$ N 1540 39.40 CI
100 1200 575 444T 1.15 93.3 95.0 E9846 $10,462 G6-7S$ N 1920 45.30 CI
100 1200 460 444T 1.15 117.0 95.0 E9133 $10,462 G6-7S$ N 1920 45.30 CI
100 900 460 445T 1.15 120.0 94.1 E9782 $16,643 G6-7S$ N 2060 45.30 CI
125 3600 460 444TS 1.15 135.0 94.5 E9511 $11,035 G6-7S$ N 1990 41.60 CI
125 3600 575 444TS 1.15 108.0 94.5 E9538 $11,035 G6-7S$ N 1990 41.60 CI
125 1800 460 444T 1.15 138.0 95.4 E9926 $10,255 G6-7S$ N 2050 45.30 CI
125 1800 460 444TS 1.15 138.0 95.4 E9927 $10,255 G6-7S$ N 2050 41.60 CI
125 1800 575 444T 1.15 110.0 95.4 E9832 $10,255 G6-7S$ N 2050 45.30 CI
125 1200 460 445T 1.15 147.0 95.0 E9135 $12,850 G6-7S$ N 1960 45.30 CI
125 1200 575 445T 1.15 117.0 95.0 E9870 $12,850 G6-7S$ N 1960 45.30 CI
125 900 460 447T 1.15 153.0 94.1 E9784 $19,308 G6-7S$ N 2550 53.80 CI
8.14 150 3600 460 445TS 1.15 162.0 94.5 E9512 $13,257 G6-7S$ N 1990 41.60 CI
150 1800 460 445T 1.15 167.0 95.4 E9928 $11,922 G6-7S$ N 2050 45.30 CI
150 1800 460 445TS 1.15 166.0 95.4 E9929 $11,922 G6-7S$ N 2050 41.60 CI
150 1800 575 445T 1.15 133.0 95.4 E9854 $11,922 G6-7S$ N 2050 45.30 CI
Definite Purpose

150 1200 460 447T 1.15 171.0 95.4 E9137 $14,377 G6-7S$ N 2920 53.80 CI
150 1200 575 447T 1.15 137.0 95.4 E9869 $14,377 G6-7S$ N 2920 53.80 CI
200 3600 460 447TS 1.15 213.0 95.0 E9961 $16,770 G6-7S$ N 2580 50.06 CI
200 1800 460 447T 1.15 223.0 95.8 E9991 $14,501 G6-7S$ N 2520 53.80 CI
200 1800 460 447T 1.15 223.0 95.8 E9958 $14,501 G6-7S$ N 2520 53.80 CI
200 1800 575 447T 1.15 179.0 95.8 E9959 $14,501 G6-7S$ N 2520 53.80 CI
200 1200 460 449T 1.15 229.0 95.4 E9139 $17,600 G6-7S$ N 2920 53.80 CI
200 1200 460 449LL 1.15 229.0 95.4 E9141 $17,600 G6-7S$ N 2920 52.10 CI
200 1200 575 449T 1.15 184.0 95.4 E9845 $17,600 G6-7S$ N 2920 53.80 CI
250 3600 460 449TS 1.00 265.0 95.0 E9514 $21,150 G6-7S$ N 2620 50.06 CI
250 1800 460 449T 1.15 279.0 95.8 E9933 $18,192 G6-7S$ N 2660 53.80 CI
250 1800 460 449T 1.15 279.0 95.8 E9988 $18,192 G6-7S$ N 2660 53.80 CI
250 1800 575 449T 1.15 223.0 95.8 E9851 $18,192 G6-7S$ N 2660 53.80 CI
250 1800 575 449T 1.15 223.0 95.8 E9989 $18,192 G6-7S$ N 2660 53.80 CI
300 1800 460 449T 1.15 331.0 95.8 E9906 $19,113 G6-7S$ N 2890 53.80 CI
300 1800 460 449T 1.15 343.0 95.8 E9990 $19,113 G6-7S$ N 2890 53.80 CI
Notes
CI Cast Iron
www.gemotors.com Data subject to change without notice. GEP-500T 03/08.
 Definite Purpose
X$D® 841 - Severe Duty
Pricing
Volts: 460, 575
HP: 20-200
Totally Enclosed Fan Cooled-Severe Duty X$D 841 – Base Mounted
Price C Dim
HP RPM Volts Frame SF FLA Nom Eff Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
20 900 460 324T 1.15 27.2 89.5 E9441 $4,963 G6-7S$8 N 710 32.00 CI
20 900 575 324T 1.15 21.7 89.5 E9574 $4,963 G6-7S$8 N 710 32.00 CI
25 1200 460 324T 1.15 30.7 92.4 E9444 $3,715 G6-7S$8 N 710 32.00 CI
25 1200 575 324T 1.15 24.6 92.4 E9577 $3,715 G6-7S$8 N 710 32.00 CI
25 900 460 326T 1.15 34.2 89.5 E9445 $5,864 G6-7S$8 N 730 32.00 CI
25 900 575 326T 1.15 27.2 89.5 E9578 $5,864 G6-7S$8 N 730 32.00 CI
30 1200 460 326T 1.15 36.8 92.4 E9448 $4,279 G6-7S$8 N 730 32.00 CI
30 1200 575 326T 1.15 29.5 92.4 E9581 $4,279 G6-7S$8 N 730 32.00 CI
30 900 460 364T 1.15 39.2 93.0 E9449 $6,946 G6-7S$8 N 1020 34.50 CI
30 900 575 364T 1.15 31.6 93.0 E9582 $6,946 G6-7S$8 N 1020 34.50 CI
40 3600 460 324TS 1.15 49.1 93.6 E9450 $3,526 G6-7S$8 N 650 30.50 CI
40 3600 575 324TS 1.15 35.2 92.4 E9583 $3,526 G6-7S$8 N 680 30.50 CI
40 1800 460 324T 1.15 49.4 94.1 E9451 $3,388 G6-7S$8 N 730 32.00 CI
40 1800 575 324T 1.15 39.5 94.1 E9584 $3,388 G6-7S$8 N 730 32.00 CI
40 1200 460 364T 1.15 46.5 93.6 E9452 $5,800 G6-7S$8 N 1070 34.50 CI
40 1200 575 364T 1.15 37.4 93.6 E9585 $5,800 G6-7S$8 N 1050 34.50 CI
40 900 460 365T 1.15 52.6 93.0 E9453 $8,574 G6-7S$8 N 1050 34.50 CI
40 900 575 365T 1.15 42.4 92.4 E9586 $8,574 G6-7S$8 N 1050 34.50 CI
50 3600 460 326TS 1.15 59.5 93.6 E9454 $4,577 G6-7S$8 N 680 30.50 CI
50 1800 460 326T 1.15 62.5 93.6 E9455 $4,160 G6-7S$8 N 740 32.00 CI
50 1800 575 326T 1.15 49.7 93.6 E9588 $4,160 G6-7S$8 N 740 32.00 CI
50 1200 460 365T 1.15 58.5 93.6 E9456 $6,659 G6-7S$8 N 1050 34.50 CI
50 1200 575 365T 1.15 46.8 93.6 E9589 $6,659 G6-7S$8 N 1050 34.50 CI
50 900 460 404T 1.15 60.3 93.0 E9457 $10,142 G6-7S$8 N 1500 39.40 CI
50 900 575 404T 1.15 48.2 93.0 E9590 $10,142 G6-7S$8 N 1500 39.40 CI
60 3600 460 364TS 1.15 69.5 94.5 E9458 $6,271 G6-7S$8 N 1000 32.40 CI
60 3600 575 364TS 1.15 55.6 94.5 E9591 $6,271 G6-7S$8 N 1000 32.40 CI
60 1800 460 364T 1.15 72.8 94.1 E9459 $5,969 G6-7S$8 N 1060 34.50 CI
60 1800 575 364T 1.15 58.2 94.1 E9592 $5,969 G6-7S$8 N 1060 34.50 CI 8.15
60 1200 460 404T 1.15 68.2 94.1 E9460 $7,672 G6-7S$8 N 1530 39.40 CI
60 1200 575 404T 1.15 55.2 94.1 E9593 $7,672 G6-7S$8 N 1530 39.40 CI
60 900 460 405T 1.15 72.3 93.0 E9461 $11,722 G6-7S$8 N 1530 39.40 CI
60 900 575 405T 1.15 57.9 93.0 E9594 $11,722 G6-7S$8 N 1530 39.40 CI

Definite Purpose
75 3600 460 365TS 1.15 89.3 93.6 E9462 $7,875 G6-7S$8 N 990 32.40 CI
75 1800 460 365T 1.15 91.5 94.1 E9463 $7,566 G6-7S$8 N 1070 34.50 CI
75 1800 575 365T 1.15 73.2 94.1 E9596 $7,566 G6-7S$8 N 1070 34.50 CI
75 1200 460 405T 1.15 87.3 94.1 E9464 $9,033 G6-7S$8 N 1490 39.40 CI
75 1200 575 405T 1.15 69.8 94.1 E9597 $9,033 G6-7S$8 N 1490 39.40 CI
75 900 460 444T 1.15 89.8 94.1 E9465 $15,215 G6-7S$8 N 1980 45.30 CI
75 900 575 444T 1.15 71.9 94.1 E9598 $15,215 G6-7S$8 N 1980 45.30 CI
Notes
CI Cast Iron

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Definite Purpose
X$D® 841 - Severe Duty
Pricing cont.

Volts: 460, 575

HP: 20-200
Totally Enclosed Fan Cooled-Severe Duty X$D 841 – Base Mounted
Price C Dim
HP RPM Volts Frame SF FLA Nom Eff Cat No. List Price Symbol Norm Stk Wt (lbs) (in) Notes
100 3600 460 405TS 1.15 110.0 94.5 E9466 $10,553 G6-7S$8 N 1480 36.40 CI
100 1800 460 405T 1.15 115.0 95.0 E9467 $9,192 G6-7S$8 N 1540 39.40 CI
100 1800 575 405T 1.15 91.7 95.0 E9693 $9,192 G6-7S$8 N 1540 39.40 CI
100 1200 460 444T 1.15 117.0 95.0 E9468 $12,031 G6-7S$8 N 1920 45.30 CI
100 1200 575 444T 1.15 93.3 95.0 E9694 $12,031 G6-7S$8 N 1930 45.30 CI
100 900 460 445T 1.15 120.0 94.1 E9469 $19,139 G6-7S$8 N 2060 45.30 CI
100 900 575 445T 1.15 95.9 94.1 E9695 $19,139 G6-7S$8 N 2060 45.30 CI
125 3600 460 444TS 1.15 135.0 94.5 E9470 $13,794 G6-7S$8 N 1990 41.60 CI
125 1800 460 444T 1.15 139.0 95.4 E9471 $11,793 G6-7S$8 N 1990 45.30 CI
125 1800 575 444T 1.15 111.0 95.4 E9697 $11,793 G6-7S$8 N 1990 45.30 CI
125 1200 460 445T 1.15 147.0 95.0 E9472 $14,778 G6-7S$8 N 1960 45.30 CI
125 1200 575 445T 1.15 117.0 95.0 E9698 $14,778 G6-7S$8 N 1960 45.30 CI
125 900 460 447T 1.15 149.0 94.5 E9473 $21,818 G6-7S$8 N 2860 53.80 CI
125 900 575 447T 1.15 119.0 94.5 E9699 $21,818 G6-7S$8 N 2860 53.80 CI
150 3600 460 445TS 1.15 162.0 94.5 E9474 $16,571 G6-7S$8 N 1990 41.60 CI
150 1800 460 445T 1.15 167.0 95.4 E9475 $13,710 G6-7S$8 N 2050 45.30 CI
150 1800 575 445T 1.15 134.0 95.4 E9384 $13,710 G6-7S$8 N 2050 45.30 CI
150 1200 460 447T 1.15 171.0 95.4 E9476 $16,246 G6-7S$8 N 2920 53.80 CI
150 1200 575 447T 1.15 137.0 95.4 E9385 $16,246 G6-7S$8 N 2940 53.80 CI
200 3600 460 447TS 1.15 213.0 95.0 E9477 $20,963 G6-7S$8 N 2580 50.60 CI
200 1800 460 447T 1.15 221.0 95.8 E9478 $16,386 G6-7S$8 N 2690 53.80 CI
200 1800 575 447T 1.15 178.0 95.8 E9387 $16,386 G6-7S$8 N 2690 53.80 CI
Notes
CI Cast Iron

8.16
Definite Purpose

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Motor Modifications

GE Motors offers various modifications to standard stock product. The following pages contain the quote/order process
along with the specific modification. Modifications can only be made to motors which are in stock and available for sale.
Typically modifications can be completed in 5 day, however it is depended upon stock availability. Please refer to EBG+ 9.1
for pricing and availability.

QUOTE/ORDER PROCESS:

Motor Modifications
GE Motors Electronic Buyer’s Guide (EBG+) is located within EliteNet, which is a web-based tool providing our customers the
ability to check stock, quote, and order all AC NEMA frame products. EBG+/EliteNet can be accessed via www.gemotors.com 24
hrs a day 7 days per week.

MODIFICATION

Altitude F-2 Mounting:

After confirmation of design conformance the motor will All Motors 140-449 are capable of being converted from F1
have a new nameplate reflecting the capabilities. to F2.

Ambient Inpro Seal®:

After confirmation of design conformance the motor will This modification is available for X$D Ultra family of
have a new nameplate reflecting the capabilities. products along with E$P. Please define the type of seal
(standard or low profile).
Condulet elbow on Conduit Box:
A conduit elbow is attached to the main conduit box Mount Coupling (Vertical Motors):
allowing the accessory leads to exit through a separate GE Motors can install couplings and steady bushing for the
conduit than the main motor leads. Value Line Vertical Hollow Shaft (V3XXX) motors.

Division 2: Re-Rate (Frequency and/or Voltage):

After confirming suitability, the maximum and internal This modifications applies to all GE Motors 180-5013 frames.
temperatures are stamped on the nameplate so that the GE Motors can re-rate 60 to 50 Hz and or 460 to 380 volt
customer can use that information in applying the motor and 230 to 200 volts.
into a Division 2 environment. GE can also provide a certified
Division 2 nameplate. Space Heaters:
GE Motors can add space heaters (standard or
Drip Cover - Steel: thermostatically controlled) to all motor 180-5013 frames. A
When the motor is applied in a vertical shaft down standard space heater is attached to the end turn. The
application a steel drip cover is attached to the fan cover. space heater leads are brought to the main conduit box.

Encoder mounting: Space Heaters (Thermostatically Controlled):

An encoder is available to mount on any of the A$D motors. A special space heater suitable for IEEE 841 and Division 2
Please consult EBG+ for options. applications. The surface temperature of the space heater is
limited to 140C. The space heater leads are brought to the
Endshield - C-Face footed: main conduit box.
A C-face Kit end shield is installed on the motor. The BA
dimension for 250 and lower frames will be the standard Thermostats:
NEMA BA, and not the NEMA C-Face BA. On 280 and higher Thermostats can be installed on all stock motors. Please
frames, the BA dimension will conform to NEMA standards. specify “B - 130 degree C” or “F - 155 degree C” alarm and
either “Normally Open” or “Normally Closed”.
Endshield - D-Flange:
A D-Flange kit is installed on the motor and the frame can Voltage:
either retain the feet or converted to a “round-body” no feet. This is to convert from a dual voltage to a single voltage ie.
230/460 to 460 volt only. This modification includes a new
Endshield - Ground Bolt: nameplate to reflect the change in voltage.
This modification is available for X$D Ultra family of
products along with E$P. Winding Resistance Temperature Detectors (RTD’s):
This modification is available on all stock motors and is
installed on winding end turns (Six 100 ohm Platinum).

Winding Thermistor (set of three):

This modification is available on all stock motors and is
installed on winding end turns.

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

9.2

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 AC Motor Selection & Application Guide
Index
50 Hertz Operation............................................................................................. 5 Lubrication.............................................................................................................. 29
Altitude..................................................................................................................... 39 Model Number Nomenclature...................................................................... 33
Ambient................................................................................................................... 21 Mounting Configurations - NEMA................................................................ 27
Applications, Quick reference…………………………………………………..………..… 47 Mounting Configurations – IEC………………………………...…………..……........... 28
Balance, Dynamic............................................................................................... 28 Mounting Configurations Comparison – IEC / NEMA…....………………. 28
Bearing Life…………………………………………………………………………………………….…. 41 Multispeed Motors.............................................................................................. 42
Bearing lubrication…………………………………………………………………………………. 29 Oil Well Pumping Motors.................................................................................. 43
Bearing Systems, Horizontal.......................................................................... 29 Paint, Special………………………………………………………………………..………………….. 40
Bearing Thermal Protection............................................................................ 36 Paint, Standard….................................................................................................. 40
Brake …..................................................................................................................... 36 Plug reversal testing…………………………………………………………..…………………... 21
Cable Glands……………………………………………………………………………..……………… 34 Polyphase Motors, 1-500 Hp.......................................................................... 8
C-Face Mounting................................................................................................. 38 Polyphase Motors, 500 Hp & Up................................................................... 12
Close Coupled Pump Motor............................................................................. 41 Polyphase, Design Comparison.................................................................... 9
Conduit Box, Special........................................................................................... 37 Power Factor.......................................................................................................... 22
Connection, Winding.......................................................................................... 26 Power, Polyphase................................................................................................. 5
Cooling...................................................................................................................... 13 Power, Single-phase........................................................................................... 5
Corona Inception Voltage………………………………………..……………………………. 21 Premium Efficiency, per NEMA…………………………………….……………………… 18
Couplings, Half...................................................................................................... 37 Premium Efficiency, per IEC…………………………………………..……………………… 19 10.1
Current Transformers........................................................................................ 34 Screens..................................................................................................................... 40
Current, General.................................................................................................. 7 Service Factor........................................................................................................ 12

Selection & Application Guide

Current, Low Starting........................................................................................ 35 Shaft Seals………………………………………………………………………………..………………. 40
D Flange Mounting.............................................................................................. 38 Shaft Slinger……………………………………………………………………………………………… 39
Design A & B (Types K & KS)............................................................................ 8 Shafts, Special....................................................................................................... 38
Design C (Types KG & KGS).............................................................................. 8 Sheave, Limiting Dimensions......................................................................... 23
Design Comparison, Polyphase.................................................................... 8 Single-phase Power............................................................................................ 12
Design D (Type KR)............................................................................................... 8 Space Heaters……………………………………………………………..…………………………… 35
Design L (Type C).................................................................................................. 12 Speed........................................................................................................................ 5
Dowel Holes........................................................................................................... 37 Starting Connections......................................................................................... 26
Drip Covers............................................................................................................. 40 Starting Frequency............................................................................................. 16
Dual Voltage……………………………………………………………………...……………………… 2 Surge Protection.................................................................................................. 35
Duty Cycle Application...................................................................................... 14 TEAO Motors.......................................................................................................... 44
Dynamic Balance................................................................................................ 28 Temperature Rise, Standard………………………………....……………….……………. 13
Efficiency levels – IEC……………………………………………………………………………… 19 Temperature Rise, Special............................................................................... 35
Efficiency, Definition........................................................................................... 17 Terminals, Special................................................................................................ 35
Enclosure / Cooling Comparison of IEC / NEMA……………..………………. 27 Testing...................................................................................................................... 20
Enclosure, Materials........................................................................................... 27 Thermal Protection............................................................................................. 35
Enclosures……………………….................................................................................... 29 Thermostats, Thermistors, RTD…………………………………………...………………. 36
Endshields, Special……........................................................................................ 37 Torque comparison IEC / NEMA for LRT, PUT & BDT………………………. 11
Explosion-Proof Motors.................................................................................... 30 Torque, Breakdown............................................................................................. 6
Export Boxing........................................................................................................ 40 Torque, Definition................................................................................................ 6
Extra Severe-Duty Motors…............................................................................ 41 Torque, Locked-rotor.......................................................................................... 6
Frame Designation, IEC / NEMA Comparison………………..………………… 27 Torque, Pull-up...................................................................................................... 6
Frame, Non-standard........................................................................................ 38 Torque....................................................................................................................... 6
Frequency, Definition......................................................................................... 4 Type KC Motors (Design L)............................................................................... 12
Frequency, Dual................................................................................................... 5 Type KR Motors (Design D)............................................................................... 8
Frequency, Standards....................................................................................... 4 Types K, KE and KS Motors (Design A & B)............................................... 8
Frequency, Variation.......................................................................................... 5 Variable Frequency Operation...................................................................... 5
Grease Fittings...................................................................................................... 38 Vertical Jack Screws…………………………………………………………..………………….. 39
Grease, Special..................................................................................................... 41 Vibration Limits………………………………………………………………………………………… 28
Grounding............................................................................................................... 34 Vibration Switch / Probe………………………………………..……………………………… 39
Hardware................................................................................................................. 40 Voltage..................................................................................................................... 2
Hazardous Locations......................................................................................... 30 Voltage, Definition............................................................................................... 2
Hazrdous Locations, per ATEX…....………………………..…............……………….. 32 Voltage, Low Starting........................................................................................ 5
Horsepower............................................................................................................ 6 Voltage, Special.................................................................................................... 2
Inertia, Load........................................................................................................... 16 Voltage, Unbalance…......................................................................................... 5
Insulation Class.................................................................................................... 13 Voltage, Variation................................................................................................ 3
Leads, Special........................................................................................................ 35 Winding Connections & Starting…………………………………………...……………. 26
Load Calculation (Belt Drive)..………………………………………………………………. 25 Winding Treatment – Custom Polyseal……………………………………………… 32
Load Connection.................................................................................................. 22 Winding Treatment – Trickle Treat……………………………..……………………… 32
Load, High Inertia................................................................................................ 16 Winding Treatment- Vacuum Pressure Impregnated…………………… 32
Losses, General.................................................................................................... 17 Winding Treatment, Special........................................................................... 32
Losses, Types of.................................................................................................... 17 X$D Ultra: Features…………………………………………………………………...……………. 42

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
VOLTAGE
DEFINITION
The motor nameplate voltage is determined by the available power NOTE: Distribution system voltages vary from country to country;
supply, which must be known in order to properly select a motor for therefore, motor nameplate voltage should be selected for the
a given application. The nameplate voltage will normally be less country in which it will be operated. Though, generally it is observed
than the nominal distribution system voltage. of nominal voltages of 230V / 400V or 400V/690V.
Additionally references for ‘System voltages’ can be found out in
The distribution voltage is the same as the supply transformer volt- IEEE 141 and IEC 60038.
age rating; the utilization (motor nameplate) voltage is set at a
slightly lower level to allow for a voltage drop in the system be- SPECIAL VOLTAGES
tween the transformer and the motor leads. Special motor designs are required for nameplate voltages other
than those listed in Tables 1 and 2. Motors greater than 100 horse-
Some specifications still call for 220, 440 or 550 volt motors which power rated less than 345 volts will not be furnished without ap-
were the long accepted standards. However, modern distribution proval of the Company. Motors with nameplate voltages different
10.2 systems have transformers located adjacent to secondary unit than those listed in Tables 1 or 2
substations or load centers, plant wide power factor correction and
Table 2: Standard 50 hertz Nameplate Voltages
Selection & Application Guide

shorter power line runs. The result is a stiffer distribution system

which delivers higher voltage at the motor. The following motor Motor
nameplate voltages provide the best match to distribution system Nominal Distribution Nameplate
voltages and meet current motor design practices. System Voltage Voltage
Table 1: Standard 60 hertz Nameplate Voltages Below 125 Hp 125 Hp & Up
Polyphase 50 hertz
Motor 200 –
Nominal Distribution Nameplate 220 –
System Voltage Voltage 380 380
Below 125 Hp 125 Hp & Up See Note 400 400
Polyphase 60 hertz 415 415
208 200 – 550 550
240 230 – 690 690
480 460 460 Single-phase 60 hertz - 3300
600 575 575 120 110 –
2400 2300 2300 208 200 –
4160 4000 4000 240 220 –
Single-phase 60 hertz
120 115 – DUAL VOLTAGE MOTORS
208 200 – Polyphase and single-phase motors may be furnished as dual volt-
240 230 – age ratings under the following conditions:

1. Both voltages are standard for the particular rating as listed in

Tables 1 and 2.

2. The two voltages are in a ratio of either 1:2 or 1:√3 (e.g. 230/460,
60 Hz; 2300/4000, 60 Hz; or 220/380, 50 Hz).

3. Single-phase voltage ratios are 1:2 only.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
VOLTAGE AND FREQUENCY VARIATION The following conditions are likely to occur with variations in fre-
All motors are designed to operate successfully with limited voltage quency:
and frequency variations. However, voltage variation with rated fre-
quency must be limited to ±10% and frequency variations with A. Frequency greater than rated frequency normally improves
rated voltage must be limited to ±5%. The combined variation of power factor but decreases locked-rotor and maximum torque.
voltage and frequency must be limited to 10% (Subject to the sum This condition also increases speed, and therefore, friction and
of absolute value with frequency variation not exceeding ± 5% of windage losses.
rated value). Variations are expressed as deviation from motor B. Conversely, a decrease in frequency will usually lower power
nameplate values, not necessarily system nominal values. The al- factor and speed while increasing locked-rotor maximum
lowable ±10% voltage variation is based upon the assumption that torque and locked-rotor current
horsepower will not exceed nameplate rating and that motor tem-
perature may increase. For instance, a 230 volt motor operating at
207 volts (90% of rated) losses any service factor indicated on the
nameplate, and could run hotter than at rated voltage.

The following conditions are likely to occur with variations in volt-

10.3
age:

Selection & Application Guide

A. An increase or decrease in voltage may result in increased
heating at rated horsepower load. Under extended operation
this may accelerate insulation deterioration and shorten motor
insulation life.

B. An increase in voltage will usually result in a noticeable decrease

in power factor. Conversely, a decrease in voltage will result in
an increase in power factor.

C. Locked-rotor and breakdown torque will be proportional to the

square of the voltage. Therefore, a decrease in voltage will result
in a decrease in available torque.

D. An increase of 10% in voltage will result in a reduction of slip of

approximately 17%. A voltage reduction of 10% would increase
Figure 2: Performance variations with respect to Frequency Variation
slip by about 21%.

Figure 1: Performance Variations with respect to Voltage Variation.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
VOLTAGE UNBALANCE LOW STARTING VOLTAGE
Unbalanced line voltages applied to a polyphase motor result in un- Large motors may experience a considerable voltage drop at the
balanced currents in the stator windings. Even a small percentage motor terminals when started due to large inrush current values.
of voltage unbalance will result in a larger percentage of current Motors can be designed to compensate for this drop in voltage. For
unbalance, thus increasing temperature rise and possibly resulting example, motors in frames 143-5013 can be supplied for operation
in nuisance tripping. under low starting voltage conditions down to 65% of nameplate
rated voltage. The inertia referred to the motor shaft, the type of
Voltages should be as evenly balanced as can be read on a volt- load (constant or variable torque), and the expected voltage drop
meter. If voltages are unbalanced, the rated horsepower of the must be provided to allow evaluation of the application for each
motor should be derated, based upon the percent unbalance, as rating involved. In any case, motors designed for low starting volt-
shown in the following graph age may have higher than standard inrush current when started on
full rated voltage.

FREQUENCY
10.4 DEFINITION
Frequency can be defined as the number of complete alternations-
Selection & Application Guide

per-second of an alternating current

Figure 3: Voltage Unbalance Vs Derating factor

Percent voltage unbalance is calculated as follows:

Maximum Voltage Deviation
Percent Unbalance = 100 x From Average Voltage
Average Voltage Figure 4
For instance, a 100 horsepower, three-phase motor operating with
As shown in Figure 4 above, current is said to have been through
voltages of 598, 575 and 552 applied at the motor terminals,
one complete cycle when it has gone from zero to maximum, to
Average Voltage = (598+575+552)/3 =575V
minimum, and back to zero again. Frequency is the number of
Voltage deviation from average Voltage= Absolute (575 -598) = 23 V;
these complete cycles over the passage of time and is usually ex-
Absolute (575 -552) = 23 V; Absolute (575 -575) = 0 V
pressed as hertz (Hz): one hertz equals one cycle per second (cps).
Maximum deviation from average voltage = 23V
Predominant frequency in North America is 60 Hz.
%Unbalance = 100*23/575 = 4%

From figure 3, the rated output of 100 horsepower should be der- FREQUENCY STANDARDS
ated to approximately 82 Hp to reduce the possibility of damage to The predominant frequency in the United States is 60 hertz. How-
the motor. Motor operation above 5% voltage unbalance is not rec- ever, 50 hertz systems are common in other countries. Other sys-
ommended. tems such as 40 and 25 hertz, are isolated and relatively few in
number.
Unbalanced voltages will produce the following effects on perform-
ance characteristics:

Torques: Unbalanced voltage results in reduced locked-

rotor and breakdown torques for the application.
Full-Load Speed: Unbalanced voltage results in a slight reduction
of full-load speed.
Current: Locked-rotor current will be unbalanced to the same
degree that voltages are unbalanced but locked-rotor
KVA will increase only slightly. Full-load current at un
balanced voltage will be unbalanced in the order of six
to ten times the voltage unbalance.
Temperature Rise: A 3.5% voltage unbalance will cause an
approximate 25% increase in temperature rise.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
50 Hz OPERATION OF 60 Hz MOTORS POLYPHASE OR SINGLE-PHASE POWER
General Electric standard motors rated at 60 Hz may be success-
fully operated at 50 Hz at reduced voltage and horsepower as
shown in the following table:
DEFINITION
A power system can be either single-phase or polyphase. Figure 4
Table 3 illustrates single-phase power, which is most commonly found in
Motor Rated 50 hertz homes, rural areas and in small commercial establishments.
60 hertz Optional
Voltage Voltage Ratings (±5%) A polyphase power system consists of two or more alternating cur-
rents of equal frequency and amplitude but offset from each other
230 190 200 208 by a phase angle. Figure 5 illustrates a three-phase power system
460 380 400 415 having phases A, B and C. Each phase is offset by 120 degrees, 360
575 475 500 – degrees being the span of one complete cycle.
De-rate factor .85 .90 1.00

• Rated Hp at 50 Hz = Nameplate Hp x De-rate Factor

• Allowable voltage variation at de-rated Hp = ±5% 10.5

• Select motor overload protection for 60 Hz amps and 1.0

Selection & Application Guide

Service Factor
• Motor speed = 5/6 nameplate rated speed
• Service Factor = 1.0

60 Hz motors intended for use as shown above should be ordered

as 60 Hz motors with no reference to 50 Hz operation. A stick-on
label containing the information shown in Table 3 is available. Figure 5: Three-phase Power

DUAL FREQUENCY For motors, an advantage of three-phase power is simpler con-

struction which requires less maintenance. Also, a more powerful
Motors that require 50 and 60 Hz operation of the same motor are
machine can be built into a smaller frame and will generally oper-
non-NEMA defined motors and will be nameplated as such. When
ate at a higher efficiency than single-phase motors of the same rat-
this is a motor requirement, it must be specified with the order.
ing.
Some of our stock motors are nameplated 50/60Hz and others can
be re-rated; refer to technical support or EliteNet.
MOTOR OUTPUT RATING
VARIABLE FREQUENCY OPERATION
Motors are available for use on variable frequency inverters of vari- SPEED
ous types: The speed at which an induction motor operates is dependent upon
the input power frequency and the number of electromagnetic
1. VVI is a square wave inverter in which voltage and frequency poles for which the motor is wound. The higher the frequency, the
vary in proportion (constant volts per hertz). faster the motor runs. The more poles the motor has, the slower it
runs. The speed of the rotating magnetic field in the stator is called
2. PWI is a pulse width modulated inverter and the same as the synchronous speed. To determine the synchronous speed of an in-
VVI type except pulses are varied in time to simulate a sine wave. duction motor, the following equation is used:

3. CCI is a constant current inverter, which utilizes a square wave 60 x 2 x Frequency

Synchronous Speed (rpm) =
current supply as opposed to voltage. Number of Poles
Actual full-load speed (the speed at which an induction motor will
4. IGBT is a pulse width modulated inverter using a bipolar transis-
operate at nameplate rated load) will be less than synchronous
tor for higher switching speeds. This technology provides a cleaner
speed. The difference between synchronous speed and full-load
resolved sine wave on a carrier frequency above the audible range.
speed is called slip. Percent slip is defined as follows:
When applying a motor for use with a variable frequency drive, see
Synchronous Speed – Full Load Speed
section on special applications (For more details, refer to Page no: Percent Slip = X 100
37). Synchronous Speed
Induction motors are built having rated slip ranging from less than
5% to as much as 20%. A motor with a slip of less than 5% is called
a normal slip motor. Motors with a slip of 5% or more are used for
applications requiring high starting torque (conveyor) and/or higher
than normal slip (punch press) where, as the motor slows down, in-
creased torque allows for flywheel energy release.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
TORQUE & HORSEPOWER The following graph illustrates a typical speed torque curve for a
Torque and horsepower are two key motor characteristics that de- NEMA design B induction motor. An understanding of several points
termine the size of motor for an application. The difference between on this curve will aid in properly applying motors.
the two can be explained using a simple illustration of a shaft and
wrench.

10.6
Selection & Application Guide

Figure 6
Torque is merely a turning effort or force acting through a radius. In
Figure 6 on page 5, it takes one pound at the end of the one foot
wrench to turn the shaft at a steady rate. Therefore, the torque re-
quired is one pound times one foot, or one pound-foot. If the
wrench were turned twice as fast, the torque required would re-
main the same, provided it is turned at a steady rate. Figure 7: Speed Torque Curve

Horsepower, on the other hand, takes into account how fast the LOCKED-ROTOR TORQUE
shaft is turned. Turning the shaft rapidly requires more horsepower Locked-rotor torque (Breakaway Torque’ or ‘Starting Torque’) is the
than turning it slowly. Thus, horsepower is a measure of the rate at torque which the motor will develop at rest (for all angular positions
which work is done. By definition, the relationship between torque of the rotor) with rated voltage at rated frequency applied. It is also
and power is as follows: sometimes known as starting torque and is usually expressed as a
1 Horsepower = 33,000 lb-ft/minute percentage of full-load torque.
Or
1 Horsepower = 0.746 kilowatt PULL-UP TORQUE
1 kilowatt = 1000 N-m/Sec Pull-up (Pull-in) torque is the minimum torque developed during the
In the above example, the one pound force moves a distance of 1 period of acceleration from locked-rotor to the speed at which
foot x 2π x 1 pound, or 6.28 feet per revolution. To produce one breakdown torque occurs. For motors which do not have a definite
horsepower, the shaft would have to be turned at a rate of: breakdown torque (such as NEMA design D) pull-up torque is the
1 Hp x 33,000 lb-ft/min/Hp minimum torque developed up to rated full-load speed. It is usually
= 5252 RPM expressed as a percentage of full-load torque.
1 lb x 2π ft/revolution
From the above, an equation is derived for determining horsepower BREAKDOWN TORQUE
output from speed and torque in lb-ft. Breakdown (Maximum or Pull-out) torque is the maximum torque
RPM x 2π x Torque RPM x Torque the motor will develop with rated voltage applied at rated fre-
Hp = or Hp = quency without an abrupt drop in speed. Breakdown torque is usu-
33,000 5252 ally expressed as a percentage of full-load torque.
Or when output is in kW and Torque is in N-m;
FULL-LOAD TORQUE
RPM x 2π x Torque RPM x Torque
kW = or kW = Full-load torque is the torque necessary to produce rated horse-
60,000 9549 power at full-load speed. In pound-feet, it is equal to the rated
From this relationship: horsepower times 5252 divided by the full-load speed in RPM.
Hp x 5252
Full-Load torque in lb-ft = MOTOR CURRENT
Full load rpm
In addition to the relationship between speed and torque, the rela-
Or
tionship of motor current to these two values is an important appli-
kW x 9549 cation consideration. The speed/torque curve is repeated below
Full-Load torque in N-m =
Full load rpm with the current curve added to demonstrate a typical relationship.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Table 4: Locked-Rotor Current Code Letters
Letter Designation KVA per Hp*
A 0 – 3.15
B 3.15 – 3.55
C 3.55 – 4.0
D 4.0 – 4.5
E 4.5 – 5.0
F 5.0 – 5.6
G 5.6 – 6.3
H 6.3 – 7.1
J 7.1 – 8.0
K 8.0 – 9.0
L 9.0 – 10.0
M 10.0 – 11.2
N 11.2 – 12.5
P 12.5 – 14.0 10.7
R 14.0 – 16.0

Selection & Application Guide

S 16.0 – 18.0
T 18.0 – 20.0
U 20.0 – 22.4
Figure 8: Speed, Torque, Current Curve V 22.4 and up
Two important points on this current curve need to be examined:
*The locked-rotor kilovolt-ampere-per-horsepower range includes
FULL-LOAD CURRENT the lower figure up to, but not including, the higher figure. For ex-
The full-load current of an induction motor is the steady-state cur- ample, 3.14 is letter “A” and 3.15 is letter “B”.
rent taken from the power line when the motor is operating at full-
load torque with rated voltage and rated frequency applied. By manipulating the preceding equation for KVA/Hp for three-
phase motors the following equation can be derived for calculating
LOCKED-ROTOR CURRENT locked-rotor current:
Locked-rotor current is the steady-state current of a motor with the
1000 x Hp x Locked-Rotor KVA/Hp
rotor locked and with rated voltage applied at rated frequency. LRA =
NEMA has designated a set of code letters to define locked-rotor √3 x Volts
kilovolt-amperes-per-horsepower. This code letter appears on the
This equation can then be used to determine approximate starting
nameplate of all AC squirrel-cage induction motors. KVA per horse-
current of any particular motor. For instance, the approximate
power is calculated as follows:
starting current for a 7.5 Hp, 230 volt motor with a locked-rotor KVA
code letter G would be:
For three-phase motors:
1000 x 7.5 x 6.0
√3 x LR current (in amperes) x volts LRA = = 113 amps
KVA/Hp = √3 x 230
1000 x Hp
For single-phase motors: Operating a motor in a locked-rotor condition in excess of 20 sec-
onds can result in insulation failure due to the excessive heat gener-
LR current (in amperes) x volts ated in the stator. Figure 9 illustrates the maximum time a motor
KVA/Hp = may be operated at locked-rotor without injurious heating. This
1000 x Hp
graph assumes a NEMA design B motor with a class B or F temper-
ature rise.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
NEMA DESIGN C [1-200Hp]

Figure 11: Typical NEMA Design C Speed/Torque Curve

10.8
GE Types: KG, KGS
Starting Current: Low
Selection & Application Guide

Figure 9: Line Current Vs. Safe Stall

time for Standard Induction Motors. Starting Torque: High
Breakdown Torque: Normal
Motor protection, either inherent or at the motor control should be
Full-Load Slip: Low (less than 5%)
selected to limit stall time of the motor.
Hard-to-start loads such as plunger,
Applications:
POLYPHASE MOTORS, 1-500 Hp pumps, conveyors and compressors.
NEMA has designated several specific types of motors, each type
having unique speed/torque relationships. These designs are de-
NEMA DESIGN D [1-150Hp]
scribed below along with some typical applications for each. Fol-
lowing these descriptions is a summary of performance
characteristics.

NEMA DESIGN A & B [1-200Hp, (250Hp-500Hp, for 2 & 4

Pole only)]

Figure 12: Typical NEMA Design D Speed/Torque Curve

GE Types: KR
Starting Current: Low
Starting Torque: Very High
Figure 10: Typical NEMA Design A & B Speed/Torque Curve Breakdown Torque: Not Applicable
Full-Load Slip: High (5-8%; 8-13%)
GE Types: K, KE, KS
Design A - High to Medium The combination of high starting Torque
Starting Current: and high slip make Type KR Motors ideal for
(not defined by NEMA)
Applications: very high inertia loads and/or for consider-
Design B - Low able variations in load; e.g., punch presses,
Starting Torque: Normal shears, cranes, hoists & elevators.
Breakdown Torque: Normal
Full-Load Slip: Low (less than 5%)
Fans, blowers, pumps, machine tools, or
Applications: other uses with low starting torque require-
ments and essentially constant load.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
The following tables compare NEMA polyphase designs for several performance criteria.
Table 5. Comparison of Polyphase Designs

NEMA Design Starting Current Locked-Rotor Torque Breakdown Torque % Slip Applications

Broad applications including fans, blowers, pumps, ma-

A High to Medium Normal Normal Max 5%
chined tools.
Normal Starting torque for fans, blowers, rotary pumps,
B Low Normal Normal Max 5% unloaded compressors, some conveyors, metal cutting
machine tools, misc machinery. Constant load speed.
High Inertia starts such as large centrifugal blowers, fly-
wheels and crusher drums. Loaded starts such as piston
C Low High Normal Max 5%
pumps, compressors and conveyors. Constant load
speed.
Very high inertia and loaded starts. Choice of slip to
D Low Very High – – 10.9
match load.
5–8% 1) Punch presses, shears and forming machine tools.

Selection & Application Guide

8–13% 2) Cranes, Hoists, elevators and oil well pumping jacks.

LOCKED ROTOR TORQUE

Table 6: Minimum Locked Rotor Torque – NEMA, MG–1, Part 12 (% Full–Load Toque)
HP Design A and B (ref. NEMA table 12-2 Design C (ref. NEMA table 12-3) Design D
RPM @ 60 Hz 3600 1800 1200 900 720 600 514 1800 1200 900 1800 1200 900
RPM @ 50 Hz 3000 1500 1000 750 - - - 1500 1000 750 1500 1000 750
1 - 275 170 135 135 115 110 285 255 225 275 275 275
1.5 175 250 165 130 130 115 110 285 250 225 275 275 275
2 170 235 160 130 125 115 110 285 250 225 275 275 275
3 160 215 155 130 125 115 110 270 250 225 275 275 275
5 150 185 150 130 125 115 110 255 250 225 275 275 275
7.5 140 175 150 125 120 115 110 250 225 200 275 275 275
10 135 165 150 125 120 115 110 250 225 200 275 275 275
15 130 160 140 125 120 115 110 225 210 200 275 275 275
20 130 150 135 125 120 115 110 200 200 200 275 275 275
25 130 150 135 125 120 115 110 200 200 200 275 275 275
30 130 150 135 125 120 115 110 200 200 200 275 275 275
40 125 140 135 125 120 115 110 200 200 200 275 275 275
50 120 140 135 125 120 115 110 200 200 200 275 275 275
60 120 140 135 125 120 115 110 200 200 200 275 275 275
75 105 140 135 125 120 115 110 200 200 200 275 275 275
100 105 125 125 125 120 115 110 200 200 200 275 275 275
125 100 110 125 120 115 115 110 200 200 200 275 275 275
150 100 110 120 120 115 115 - 200 200 200 275 275 275
200 100 100 120 120 115 - - 200 200 200 - - -
250 70 80 100 100 - - - - - - - - -
300-350 70 80 100 - - - - - - - - -
400-500 70 80 - - - - - - - - - - -

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
PULL-UP TORQUE
The pull-up torque for NEMA design A, B and C motors are listed in Table 7 with rated voltage and frequency applied will not be less than the
following:
Table 7: Minimum Pull-up Torque - NEMA MG-1, Part 12 (% of full load torque)
HP Design A and B (reference NEMA Section: 12.40.1) Design C (ref. NEMA section: 12.40.2)
RPM @ 60 Hz 3600 1800 1200 900 720 600 514 1800 1200 900
RPM @ 50 Hz 3000 1500 1000 750 - - - 1500 1000 750
1 - 190 120 120 100 100 100 195 180 165
1.5 120 175 115 115 100 100 100 195 175 160
2 120 165 110 110 100 100 100 195 175 160
3 110 150 110 110 100 100 100 180 175 160
5 105 130 105 105 100 100 100 180 175 160
7.5 100 120 105 105 100 100 100 175 165 150
10 100 115 105 105 100 100 100 175 165 150
15 100 110 100 100 100 100 100 165 150 140
20 100 105 100 100 100 100 100 165 150 140
10.10 25 100 105 100 100 100 100 100 150 150 140
30 100 105 100 100 100 100 100 150 150 140
40 100 100 100 100 100 100 100 150 150 140
Selection & Application Guide

50 100 100 100 100 100 100 100 150 150 140
60 100 100 100 100 100 100 100 140 140 140
75 95 100 100 100 100 100 100 140 140 140
100 95 100 100 100 100 100 100 140 140 140
125 90 100 100 100 100 100 100 140 140 140
150 90 100 100 100 100 100 100 140 140 140
200 90 90 100 100 100 - - 140 140 140
250 65 75 90 90 - - - - - -
300-350 65 75 90 - - - - - - -
400-500 65 75 - - - - - - - -

BREAKDOWN TORQUE
Table 8: Minimum Breakdown Torque - NEMA MG-1, Part 12 (% of Full-Load Torque)
Design A and B (reference NEMA Section: 12.39.1) Design C (ref. NEMA section: 12.39.2)
RPM @ 60 Hz 3600 1800 1200 900 720 600 514 1800 1200 900
RPM @ 50 Hz 3000 1500 1000 750 - - - 1500 1000 750
1 - 300 265 215 200 200 200 200 225 200
1.5 250 280 250 210 200 200 200 200 225 200
2 240 270 240 210 200 200 200 200 225 200
3 230 250 230 205 200 200 200 200 225 200
5 215 225 215 205 200 200 200 200 200 200
7.5 200 215 205 200 200 200 200 200 190 190
10 200 200 200 200 200 200 200 200 190 190
15 200 200 200 200 200 200 200 200 190 190
20 200 200 200 200 200 200 200 200 190 190
25 200 200 200 200 200 200 200 190 190 190
30 200 200 200 200 200 200 200 190 190 190
40 200 200 200 200 200 200 200 190 190 190
50 200 200 200 200 200 200 200 190 190 190
60 200 200 200 200 200 200 200 190 190 190
75 200 200 200 200 200 200 200 190 190 190
100 200 200 200 200 200 200 200 190 190 190
125 200 200 200 200 200 200 200 190 190 190
150 200 200 200 200 200 200 - 190 190 190
200 200 200 200 200 200 - - 190 190 190
250 175 175 175 175 - - - - - -
300 175 175 175 - - - - - - -
300 175 175 175 - - - - - - -
400-500 175 175 - - - - - - - -

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Table 9: Comparison of IEC / NEMA Starting Characteristics for Normal Starting Torque Cage Motors
Number of Poles 2 4 6 8
Hp kW Tl Tu Tb Tl Tu Tb Tl Tu Tb Tl Tu Tb
3 2.2 170/160 100/100 200/230 180/215 120/150 200/250 160/155 110/110 190/230 140/130 100/100 180/205
5 3.7 160/150 110/105 200/215 170/185 120/130 200/225 150/150 110/105 190/215 130/130 100/100 180/205
7.5 5.5 150/140 100/100 200/200 160/175 110/120 200/215 150/150 110/105 190/205 130/125 100/100 180/200
10 7.5 150/135 100/100 200/200 160/165 110/115 200/200 150/150 110/105 180/200 135/125 100/100 170/200
15-20 11-15 140/130 100/100 200/200 150/150 110/105 200/200 140/135 100/100 180/200 120/125 90/100 170/200
25-30 18.5-22.5 130/130 90/100 190/200 140/150 100/105 190/200 140/135 100/100 180/200 120/125 90/100 170/200
40-50 30-37 120/120 90/100 190/200 130/140 100/100 190/200 130/135 100/100 180/200 120/125 90/100 170/200
60-75 45-56 110/105 80/95 180/200 120/140 90/100 180/200 120/135 90/100 170/200 110/125 80/100 170/200
100-125 75-93 100/100 70/90 180/200 110/110 80/100 180/200 110/125 80/100 170/200 100/120 70/100 160/200
10.11
150-200 110-150 90/100 70/90 170/200 100/100 80/90 170/200 100/120 80/100 170/200 90/120 70/100 160/200
250-300 186-220 80/70 60/65 170/175 90/80 70/70 170/175 90/100 70/90 160/175 90/60 70/60 160/175

Selection & Application Guide

350-500 260-370 75/70 60/65 160/175 75/80 60/70 160/175 75/60 60/60 160/175 75/60 60/60 160/175
600-800 450-600 65/60 50/60 160/175 65/60 50/60 160/175 65/60 50/60 160/175 65/60 50/60 160/175

Notes:
(1) First value indicates IEC and Second value indicates NEMA.
(2) Tl = Locked rotor torque, percentage of full-load torque.
(3) Tu = Pull-up Torque, percentage of full-load torque.
(4) Tb = Breakdown torque, percentage of full-load torque.
(5) Minimum values with no negative tolerance.
(6) IEC value applies to indicate horsepower (kilowatt) range. NEMA value corresponds to maximum horsepower and the torques for
the lower horsepower(s) are equal to or greater than the value shown.
(7) Where the horsepower’s are in scope, this table is for NEMA Designs A or B and IEC Design N.

Table 10: Comparison of IEC / NEMA Starting Characteristics for High Starting Torque Cage Motors

Number of Poles 4 6 8
Hp kW Tl Tu Tb Tl Tu Tb Tl Tu Tb
3 2.2 270/* 180/* 200/* 240/255 165/175 190/225 210/225 150/160 190/200
5 3.7 255/250 180/175 200/200 225/250 165/175 190/200 200/225 150/160 190/200
7.5-10 5.5-7.5 240/250 165/175 200/190 225/225 165/160 190/190 200/200 150/140 190/190
15 11 225/225 165/160 200/190 210/200 150/140 190/190 200/200 140/140 190/190
20 15 225/200 165/140 200/190 210/200 150/140 190/190 200/200 140/140 190/190
30 22.5 210/200 150/140 190/190 210/200 150/140 190/190 200/200 140/140 190/190
40-50 30-37 200/200 150/140 190/190 200/200 150/140 190/190 200/200 140/140 190/190
75-200 55-150 200/200 140/140 190/190 200/200 140/140 190/190 200/200 140/140 190/190

Notes:
(1) Please refer above Notes from (1) to (6)
(2) *Not defined in NEMA. Design B torques normally adequate for 3 Hp or less.
(3) This is table is for NEMA Design C and IEC Design H.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
POLYPHASE MOTORS LARGER THAN 500 Hp Breakdown torques developed by Design L motors are shown in the
following table:
Ratings larger than those listed in Tables 6, 7 and 8 are not covered
by NEMA design letters, but have minimum torques established by Table 12: Single-phase (Design L) Breakdown Torque in lb-ft
NEMA MG-1 as follows: (NEMA MG-1, Part 10)
Frequency (hertz)
Table 11: Motor Torque - NEMA MG-1, Part 20
60 50 60 50 60 50
Torque *Minimum % of Rated Full-Load Torque Synchronous Speed
Hp
3600 3000 1800 1500 1200 1000
Locked-Rotor 60
1 – – 5.16-6.8 6.19-8.2 6.9-9.2 *
Pull-up 60
1.5 3.6-4.6 4.3-5.5 6.8-10.1 8.2-12.1 9.2-13.8
Breakdown 175 2 4.6-6.0 5.5-7.2 10.1-13.0 12.1-15.6 13.8-18.0 *
* Higher values can be quoted for specific applications. 3 6.0-8.6 7.2-10.2 13.0-19.0 15.6-22.8 18.0-25.8 *
5 8.6-13.5 10.2-16.2 19.0-30.0 22.8-36.0 25.8-40.5 *
Locked-rotor current of these designs will normally not exceed 7.5 13.5-20.0 16.2-24.0 30.0-45.0 36.0-54.0 40.5-60.0 *
10.12 650% of full-load current, and will normally be within NEMA locked- 10 20.0-27.0 24.0-32.4 45.0-60.0 54.0-72.0 * *
rotor KVA limits for a code G or H motor. * No torque values have been established for these ratings
Selection & Application Guide

SINGLE-PHASE MOTORS Maximum locked-rotor currents for Design L, 60 Hz motors are

shown in the following table:
NEMA DESIGN L Table 13: Single-phase Maximum Locked-Rotor
Current in Amperes at 230 Volts - NEMA MG-1, Part 12
Hp amps
1 45
1.5 50
2 65
3 90
5 135
7.5 200
10 260

SERVICE FACTOR
Service factor is defined as the permissible amount of overload a
motor will handle within defined temperature limits. When voltage
and frequency are maintained at nameplate rated values, the
motor may be overloaded up to the horsepower obtained by multi-
Figure 13: Typical NEMA Design L Speed/Torque Curve plying the rated horsepower by the service factor shown on the
nameplate. However, locked-rotor torque, locked-rotor current and
A NEMA design L motor is a single-phase integral horsepower breakdown torque are unchanged. NEMA has defined service factor
motor designed to withstand full-voltage starting. The GE offering to values for standard polyphase dripproof, 60 Hz motors as shown in
meet design limits of design L is a type KC. Starting performance of the following table:
type KC motors is dependent upon an additional winding controlled
Table 14: Service Factor
by a centrifugal mechanism and switch. Upon energization of the
motor, both windings and the run winding of the motor are con- Synchronous Speed
Hp
nected to the line. As the motor comes up to speed, the centrifugal 3600 1800 1200 900 720 600 514
mechanism will actuate and open the switch, removing the start
provisions from the line. The RPM at which this occurs is known as 1 1.25 1.15* 1.15* 1.15* 1.0 1.0 1.0
“switch speed”. The motor will then operate at full-load with only 1.5 - 125 1.15* 1.15* 1.15* 1.15* 1.15* 1.15* 1.15*
the run windings connected. 150 1.15* 1.15* 1.15* 1.15* 1.15* 1.15* 1.0
200 1.15* 1.15* 1.15* 1.15* 1.15* 1.0 1.0
Over 200 1.0 1.0 1.0 1.0 1.0 1.0 1.0

* These service factors apply only to NEMA design

A, B and C motors

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
MOTOR TEMPERATURE 4. Ambient air density
A reduction in the ambient air density will result in a reduction of
A major consideration in both motor design and application is heat.
the rate of heat transfer from the motor. Therefore, total operating
Excessive heat will accelerate motor insulation deterioration and
temperature increases with altitude. Standard motors are suitable
cause premature insulation failure. Excessive heat may also cause
for operation up to 3300 feet; motors with service factor may be
a breakdown of bearing grease, thus damaging the bearing system
used at altitudes up to 9900 feet at 1.0 service factor.
of a motor.
INSULATION CLASS vs. TEMPERATURE
The total temperature a motor must withstand is the result of two
NEMA has classified insulation systems by their ability to provide
factors: external, or ambient temperature; and internal, or motor
suitable thermal endurance. The total temperature is the sum of
temperature rise. An understanding of how these components are
ambient temperature plus the motor’s temperature rise. The follow-
measured and expressed is important for proper motor application.
ing charts illustrate the maximum total motor temperature allowed
for each of the standard classes of insulation. An additional 10 de-
For a given application, the maximum sustained ambient tempera-
grees C measured temperature rise is permitted when tempera-
ture, measured in degrees Centigrade (Celsius), should be deter-
tures are measured by detectors embedded in the winding. Figures
mined. The ambient temperature is the temperature that the motor
14-17 illustrate the temperature rise limits established for various
sees. If the motor is in a housing or chamber, then the ambient 10.13
insulation classes per NEMA MG-1, Part 12.
temperature is the temperature inside the housing. Most motors are
designed to operate in a maximum ambient temperature of 40°C. If

Selection & Application Guide

NOTE: It has been observed that for every 10 C above rated in-
the ambient temperature exceeds 40°C, the motor may need to be
sulation temperature [i.e. for a class F insulation system if a
modified to compensate for the increase in total temperature.
motor runs at 165 C (exceeding the 155 C)], and then the insu-
lation life is cut to half. So, for every 10 C below the rated tem-
The temperature rise is the result of heat generated by motor losses
perature, the insulation life is doubled.
during operation. At no-load, friction in the bearings, core losses
(eddy current and hysteresis losses), and stator I2R losses con-
tribute to temperature rise; at full-load, additional losses which ENCLOSURE: DRIPPROOF OR TEFC
cause heating are rotor I2R losses and stray load losses. (NOTE: I = SERVICE FACTOR: 1.0
current in amps and R = resistance of the stator or rotor in ohms).

Motor current increases with an increase in load and under locked-

rotor, temperature rise will be significantly higher under these con-
ditions. Therefore, applications requiring frequent starting and/or
frequent overloads may require special motors to compensate for
the increase in total temperature.

MOTOR COOLING
The total temperature of a motor is greater than the surrounding
environment; heat generated during motor operation will be trans-
ferred to the ambient air. The rate of heat transfer affects the maxi-
mum load and/or the duty cycle of a specific motor design. Factors
affecting this rate of transfer are:

1. Motor enclosure
Different enclosures result in different airflow patterns which alter
the amount of ambient air in contact with the motor.

2. Frame surface area

Increasing the area of a motor enclosure in contact with the ambi-
ent air will increase the rate of heat transfer. General Electric motor
enclosures often are cast with many ribs to increase their surface Figure 14
area for cooler operation.

3. Airflow over motor

The velocity of air moving over the enclosure affects the rate of
heat transfer. Fans are provided on most totally-enclosed and some
open motors to increase the velocity of air over the external parts.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
ENCLOSURE: TENV DUTY CYCLE APPLICATIONS
SERVICE FACTOR: 1.0
INSULATION CLASS
TYPES OF DUTY
The duty cycle of a motor describes the energization/de-energiza-
tion, and load variations, with respect to time for any given applica-
tion. Duty cycle applications may be divided into three basic
classifications:

1. Continuous duty is a requirement of service that demands

operation at an essentially constant load for an indefinitely long
time. This is the most common duty classification and accounts
for approximately 90% of motor applications. To size a motor
for a specific application with this duty cycle classification,
select proper horsepower based upon continuous load.

10.14 2. Intermittent duty is a requirement of service that demands

operation for alternate intervals of load and no-load; or load
and rest; or load, no-load and rest; each interval of which is
Selection & Application Guide

definitely specified. Select a motor for these applications to

Figure 15 match the horsepower requirements under the loaded
ENCLOSURE: DRIPPROOF OR TEFC condition. In some instances, such as a hoist or elevator
SERVICE FACTOR: 1.15 application, savings in the purchase price of a motor may be
INSULATION CLASS possible by designing for the intermittent duty cycle. 30 or 60
minute motors are normally specified. Frequent starts, however,
can increase motor heating.

3. Varying duty is a requirement of service that demands

operation at loads and for intervals of time, which may be
subject to wide variation. For this classification of duty cycle, a
horsepower versus time curve will permit determination of the
peak horsepower required and a calculation of the root-mean-
square (RMS) horsepower will indicate the proper motor rating
from a heating standpoint. The following example
demonstrates the method for selecting a motor for a varying
duty cycle based upon peak horsepower and RMS horsepower
requirements assuming constant frequency.

Figure 16
ENCLOSURE: X$D Ultra®
SERVICE FACTOR: 1.0

Figure 18: Duty Cycle Calculations

Figure 17
* Note: 47 C is the weighted average temperature rise for X$D-
Ultra ® Motors, per Ecomagination Product Review (EPR –Rev 11-
29-2007).

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
To properly size a motor for the varying duty cycle described in the The motor must also be capable of carrying the peak horsepower
preceding horsepower versus time graph, a table should be made (torque) value from the duty cycle at 90% voltage. Since motor
as shown quantifying each part of the cycle. The first three columns breakdown torque is reduced by the voltage squared, the required
of this table list data from the graph, and the fourth column is de- breakdown torque (BDT) is determined by the equation:
rived by squaring the horsepower and multiplying by the time for

[ ]
each part of the cycle. Using this data, sum the periods of time and Peak-Load Hp X 100
(Hp)2t, and evolve the RMS horsepower as follows: %BDT = +20 (see note)
NP Hp X .92
Table 15
Part of Cycle Time Sec. (t) Required Hp (Hp)2t

[ ]
1 15 32 15,360 Peak-Load Hp X 123
2 40 74 219,040 = +20
3 30 27 21,870 NP Hp
4 5 32 5,120
5 148 66 644,688 NP Hp = Nameplate Rated Horsepower
6 200 27 145,800 %BDT = Percent Breakdown Torque
7 12 32 12,288 10.15
8 70 27 51,030 NOTE: Margin of 20% added to prevent inefficiencies of operation
too close to actual breakdown torque.

Selection & Application Guide

520 1,115,196

For example, with a 50 Hp motor at 1.15 SF:

∑ (Hp)2t %BDT = [74/50 x 123 + 20] = 202%

RMS Hp =
∑t For 60 Hp at 1.0 SF:

%BDT = [74/60 x 123 + 20] = 172%

RMS Hp = Root-Mean-Square Horsepower
Conclusion: Since the NEMA breakdown torque for a 50 Hp or 60 Hp
motor is 200%, the best choice for the application is the 60 Hp rat-
1,115,196 ing which only requires 172% at the peak-load horsepower.
RMS Hp = = 2,145 = 46.3 Hp
520

The load RMS horsepower is used to determine the required motor

thermal capability at constant speed. To allow for ±10% voltage
variation and the resulting additional motor heating, particularly at
peak loads and 90% voltage, a 10% allowance is added to the RMS
horsepower calculation:

Required Hp = RMS Hp x 1.10

= 46.3 x 1.10 = 50.9 Hp

The motor usable horsepower is determined by the nameplate Hp x

service factor and must be equal to or greater than the required
horsepower. In our example, there is a choice of either a 50 Hp
motor with a 1.15 service factor or a 60 Hp motor at a 1.0 service
factor. From a thermal viewpoint, either of these ratings is suitable
for the required load Hp of 50.9.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
Duty Cycles per IEC: second. Starting losses may be so low that the start cycle could be
Standardized coded duty cycles for use of purchaser to define the repeated several times per minute without overheating the winding.
expected or any equivalent loading condition, and which may be However, motor life can be limited by mechanical starting stresses.
used by the manufacturer in defining the rating. The basic duty When frequent starting is planned refer to NEMA MG-10.
types are:
S1 - Continuous Running duty HIGH INERTIA LOADS
S2 - Short time duty At the other extreme, the same motor connected to a high inertia
S3 - Intermittent periodic duty load (such as a large centrifugal blower) could burn out before get-
S4 - Intermittent periodic duty with starting ting up to full speed on the first start. Motor applications involving
S5 - Intermittent periodic duty with electric braking frequent starts or high load inertia must be carefully studied to ob-
S6 - Continuous operation periodic duty tain satisfactory operation and long motor life.
S7 - Continuous operation periodic duty with electric braking.
S8 - Continuous operation periodic duty with related load / The following table lists recommended maximum load inertias for
speed changes type K, KG, KS and KGS, 60 or 50 Hz, motors starting a fan or cen-
S9 - Duty with non-periodic load and speed variations trifugal pump load for two successive cold starts or one start from
S10- Duty with not more than 4 discrete values. rated load temperature. The cold starts should be possible within 10
10.16
seconds of each other at rated frequency and voltage, and permit-
STARTING LOAD INERTIA (WK2) ted by conventional control. It is recommended, however, that high
Selection & Application Guide

In any type of duty cycle operation, it is necessary to determine not inertia drives have thermal protection in the motor to prevent
only the horsepower requirements but the number of times the burnout from misapplication or excessive starting frequency.
motor will be started, the inertia of the driven machine, the type of
load (constant or variable torque) and the method of stopping the Table 16: Maximum Load Inertia NEMA MG-1, Parts 12 and 20
motor. Speed, RPM
Hp 3600 1800 1200 900 720 600 514
The inertia (WK2) of the rotating parts of the driven equipment af- Load WK
2
(Exclusive of Motor WK ) lb-ft
2 2

fects the acceleration time and motor heating during acceleration. 1 - 5.8 15 31 53 82 118
The heating of motor rotor and stator during frequent starting,
1.5 1.8 8.6 23 45 77 120 174
stopping, and/or reversals can become a design limitation.
2 2.4 11 30 60 102 158 228
If the motor is direct connected, the inertia supplied by the equip- 3 3.5 17 44 87 149 231 335
ment manufacturer may be used as is. If the motor is to drive the 5 5.7 27 71 142 242 375 544
equipment through a pulley or gear such that the driven equipment 7.5 8.3 39 104 208 356 551 798
is operating at a higher or lower speed than the motor, it is neces- 10 11 51 137 273 467 723 1048
sary to calculate the inertia referred to the motor shaft; that is, an 15 16 75 200 400 685 1061 1538
equivalent inertia based on the speed of the motor. 20 21 99 262 525 898 1393 2018
25 26 122 324 647 1108 1719 2491
WK2 (Referred to Motor Shaft) = 30 31 144 384 769 1316 2042 2959
40 40 189 503 1007 1725 2677 3881
RPM2 (Driven Equipment)
WK2 (Driven Equipment) x 50 49 232 620 1241 2127 3302 4788
RPM2 (Motor) 60 58 275 735 1473 2524 3819 5680
The method of stopping the motor is also taken into consideration 75 71 338 904 1814 3111 4831 7010
in a duty cycle calculation. For example, if the motor is allowed to 100 92 441 1181 2372 4070 6320 9180
coast to a stop or mechanical braking is used; the RMS horsepower 125 113 542 1452 2919 5010 7790 11310
calculation may be affected. Plug stopping or DC braking increases 150 133 640 1719 3456 5940 9230 -
motor heating considerably. Therefore, the method of stopping 200 172 831 2238 4508 7750 12060 -
must be part of the duty cycle data provided. 250 210 1017 2744 5540 9530 14830 -
300 246 1197 3239 6540 11270 - -
STARTING FREQUENCY 350 281 1373 3723 7530 - - -
A special kind of duty cycle is one in which a motor is required to 400 315 1546 4199 8500 - - -
perform repetitive starts with a given load and connected inertia.
450 349 1714 4666 9460 - - -
Motor selection must take into account the motor heating caused
500 381 1880 5130 - - - -
by starting frequency, load inertia and running load.
600 443 2202 6030 - - - -
A motor during acceleration draws about 6 times full-load current, 700 503 2514 - - - - -
so resistance losses during starting are up to 36 times (current 800 560 2815 - - - - -
squared) the losses at full-load. A motor operating on a low inertia
load (pump) may come up to speed very quickly, in less than one

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
EFFICIENCY Energy Policy Act (EPAct)
GE Motors has noted all EPAct items as “KE” in the model numbering
DEFINITION system. These models meet or exceed the EPAct law as stated in
Efficiency is an important application consideration. This is espe- this table.
cially true for applications having high hours of operation where Table 17: Nominal Efficiency Levels Covered by EPAct
cost of motor operation is many times the initial purchase price of
the motor. Enclosed Motors Open Motors
Motor
As shown below, efficiency is defined as watts output over watts Hp
6 pole 4 pole 2 pole 6 pole 4 pole 2 pole
input using 746 watts as the equivalent of one horsepower:
1 80.0 82.5 75.5 80.0 82.5 —
746 x Hp Output Watts Output 1.5 85.5 84.0 82.5 84.0 84.0 82.5
Efficiency = = 2 86.5 84.0 84.0 85.5 84.0 84.0
Watts Input Watts Input
3 87.5 87.5 85.5 86.5 86.5 84.0
This can also be expressed as the watts input minus the losses di- 5 87.5 87.5 87.5 87.5 87.5 85.5
vided by the watts input. 7.5 89.5 89.5 88.5 88.5 88.5 87.5 10.17
10 89.5 89.5 89.5 90.2 89.5 88.5
Input - Losses 15 90.2 91.0 90.2 90.2 91.0 89.5

Selection & Application Guide

Efficiency =
Input 20 90.2 91.0 90.2 91.0 91.0 90.2
25 91.7 92.4 91.0 91.7 91.7 91.0
The only way to improve efficiency is to reduce losses. Although 30 91.7 92.4 91.0 92.4 92.4 91.0
input power is readily measured, power out is difficult to measure 40 93.0 93.0 91.7 93.0 93.0 91.7
accurately. Therefore, precision equipment is required to determine 50 93.0 93.0 92.4 93.0 93.0 92.4
the efficiency and the losses in a motor. Standard test procedures 60 93.6 93.6 93.0 93.6 93.6 93.0
are defined to measure the individual components of loss sepa- 75 93.6 94.1 93.0 93.6 94.1 93.0
rately in order to improve the accuracy of efficiency determination. 100 94.1 94.5 93.6 94.1 94.1 93.0
125 94.1 94.5 94.5 94.1 94.5 93.6
DESCRIPTION OF MOTOR LOSSES 150 95.0 95.0 94.5 94.5 95.0 93.6
Typically, motor losses are categorized, first, as those which occur 200 95.0 95.0 95.0 94.5 95.0 94.5
while the motor is energized but operating at no-load; and, second,
those additional losses due to the output load. Specific losses are: The following motor products are currently exempt from U.S. and
Canadian legislation:
1. No-load losses • NEMA C and D Designs 200
a. Windage and friction • 575 Volt Multispeed Integral Brake Motors
b. Stator iron losses • Motors Above 200 or Below 1 Hp
c. Stator I2R losses • Single Phase
• Direct Current (DC)
2. Load Losses • Totally-Enclosed Air-Over
a. Stator I2R losses (due to increase in current under load) • Totally-Enclosed Non Vent
b. Rotor I2R • Close Coupled Pump (JM/JP) 50 Hertz
c. Stray load losses
The Canadian Energy Act parallels the U.S. law with some specific
The no-load losses and the conductor losses under load can be differences. The Canadian legislation includes:
measured separately; however, the stray load loss requires accu- • 200 and 575 Volt
rate input-output test equipment for determination. The stray-load • Integral Brake Motors
loss consists of losses due to harmonic currents and flux in the • 50 Hz Motors
motor. Factors affecting stray load losses include:

• Stator and rotor slot geometry

• Number of slots
• Air gap length
• Rotor slot insulation
• Manufacturing process

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
NEMA Premium Efficiency: GE’s X$D Ultra® family of products, offers ‘minimum guaranteed ef-
GE Motors has noted ‘NEMA Premium Efficiency’ items as “KS” in the ficiency’ at 1 band below the nominal value.
model numbering system. These models exceed or meet the NEMA
Premium Efficiency (except for special motors like Vertical High Quick comparison, of ‘1-band low’ & ‘2-band low’; for minimum
Thrust motors .etc) as stated in the table: guaranteed efficiency levels (Per NEMA).
Table 18: NEMA Premium Efficiency Nominal level; Table 19: Comparison of Minimum Guaranteed Efficiency Levels
reference Table 12-12NEMA (MG1-2006)
Minimum Guaranteed Minimum Guaranteed
Nominal Efficiency Nominal Efficiency
Enclosed Motors Open Motors Value Value
Motor 1-band 2-band 1-band 2-band
Hp
6 pole 4 pole 2 pole 6 pole 4 pole 2 pole 98.6 98.5 98.4 91.7 91.0 90.2
98.5 98.4 98.2 91.0 90.2 89.5
1 82.5 85.5 77.0 82.5 85.5 77.0 98.4 98.2 98.0 90.2 89.5 88.5
1.5 87.5 86.5 84.0 86.5 86.5 84.0 98.2 98.0 97.8 89.5 88.5 87.5
2 88.5 86.5 85.5 87.5 86.5 85.5 98.0 97.8 97.6 88.5 87.5 86.5
10.18
3 89.5 89.5 86.5 88.5 89.5 85.5 97.8 97.6 97.4 87.5 86.5 85.5
5 89.5 89.5 88.5 89.5 89.5 86.5 97.6 97.4 97.1 86.5 85.5 84.0
Selection & Application Guide

7.5 91.0 91.7 89.5 90.2 91.0 88.5 97.4 97.1 96.8 85.5 84.0 82.5
10 91.0 91.7 90.2 91.7 91.7 89.5 97.1 96..8 96.5 84.0 82.5 81.5
15 91.7 92.4 91.0 91.7 93.0 90.2 96.8 96.5 96.2 82.5 80.0 81.5
20 91.7 93.0 91.0 92.4 93.0 91.0 96.5 96.2 95.8 81.5 80.0 78.5
25 93.0 93.6 91.7 93.0 93.6 91.7 96.2 95.8 95.4 80.0 78.5 77.0
30 93.0 93.6 91.7 93.6 94.1 91.7 95.8 95.4 95.0 78.5 77.0 75.5
40 94.1 94.1 92.4 94.1 94.1 92.4 95.4 95.0 94.5 77.0 75.5 74.0
50 94.1 94.5 93.0 94.1 94.5 93.0 95.0 94.5 94.1 75.5 74.0 72.0
60 94.5 95.0 93.6 94.5 95.0 93.6 94.5 94.1 93.6 74.0 72.0 70.0
75 94.5 95.4 93.6 94.5 95.0 93.6 94.1 93.6 93.0 72.0 70.0 68.0
100 95.0 95.4 94.1 95.0 95.4 93.6 93.6 93.0 92.4 70.0 68.0 66.0
125 95.0 95.4 95.0 95.0 95.4 94.1 93.0 92.4 91.7 68.0 66.0 64.0
150 95.8 95.8 95.0 95.4 95.8 94.1 92.4 91.7 91.0 66.0 64.0 62.0
200 95.8 96.2 95.4 95.4 95.8 95.0
250 95.8 96.2 95.8 95.4 95.8 95.0

300 95.8 96.2 95.8 95.4 95.8 95.4

350 95.8 96.2 95.8 95.4 95.8 95.4
400 95.8 96.2 95.8 95.8 95.8 95.8
450 95.8 96.2 95.8 96.2 96.2 95.8
500 95.8 96.2 95.8 96.2 96.2 95.8

The “minimum guaranteed efficiency”, below nominal value:

1. Per NEMA is 2 bands –OR (as applicable)-
2. Per EPAct law requires the motor losses to be no more than
15% lower than nameplate. Referred to the federal registry
10 CFR Part 431, and section 431.24.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
IEC Efficiency levels: Table 21: Indicative Values (%) of IEC premium efficiency (IE3) for 50 Hz
Present Efficiency Norms (as on Oct – 2007): KW Hp 2-pole 4-pole 6-pole
Efficiency levels, defined by EU Eco-design of Energy-using Prod- 0.75 1.0 82.1 84.0 80.6
ucts Directive, are represented as follows: 1.1 1.5 83.8 85.3 82.4
1.5 2 85.1 86.3 83.8
EFF1 for their best in class efficiency levels. 2.2 3 86.4 87.5 85.4
EFF2 for their standard efficiency levels. 3 4 87.5 88.4 86.6
EFF3 lower level, for a family of motors that the Government 4 5.4 88.4 89.2 87.7
Regulations (EU in Europe) are encouraging 5.5 7.4 89.4 90.0 88.7
manufacturer’s and Motor users’ to discontinue. 7.5 10 90.3 90.8 89.7
11 15 91.2 91.7 90.8
Table 20: EFF1 / EFF2 / EFF3 efficiency level comparison (50 Hz) 15 20 91.9 92.3 91.6
% Efficiency 18.5 25 92.4 92.7 92.1
Motor rating 22 30 92.7 93.1 92.5
4 pole 2 pole 30 40 93.3 93.6 93.1
EFF1 EFF2 EFF1 EFF2 37 50 93.7 94.0 93.5
EFF3 EFF3 45 60 94.0 94.3 93.9 10.19
KW Hp Equal to Equal to Equal to Equal to
below below 55 74 94.3 94.5 94.2
or above or above or above or above
75 100 94.7 95.0 94.7

Selection & Application Guide

1.1 1.5 83.8 76.2 82.8 76.2 90 120 95.0 95.2 94.9
1.5 2 85.0 78.5 84.1 78.5 110 150 95.2 95.4 95.2
2.2 3 86.4 81.0 85.6 81.0 132 175 95.4 95.6 95.4
3 4 87.4 82.6 86.7 82.6 160 210 95.6 95.8 95.6
4 5.4 88.3 84.2 87.6 84.2 200 & above 265 & above 95.8 96.0 95.8
5.5 7.4 89.2 85.7 88.6 85.7
7.5 10 90.1 87.0 89.5 87.0 Table 22: Comparison of Efficiency Levels (Pre-EPact / Epact /
11 15 91.0 88.4 90.5 88.4 Premium), for 4-Pole Totally Enclosed Motors for 60Hz
15 20 91.8 89.4 91.3 89.4 Size (hp) Pre-EPAct1 EPAct2 NEMA Premium4
18.5 25 92.2 90.0 91.8 90.0
1 76.7 82.5 85.5
22 30 92.6 90.5 92.2 90.5
1.5 79.1 84.0 86.5
30 40 93.2 91.4 92.9 91.4 2 80.8 84.0 86.5
37 50 93.6 92.0 93.3 92.0 3 81.4 87.5 89.5
45 60 93.9 92.5 93.7 92.5 5 83.3 87.5 89.5
55 74 94.2 93.0 94.0 93.0 7.5 85.5 89.5 91.7
75 100 94.7 93.6 94.6 93.6 10 85.7 89.5 91.7
90 120 95.0 93.9 95.0 93.9 15 86.6 91.0 92.4
20 88.5 91.0 93.0
IEC & NEMA follows different methods for efficiency calculations, 25 89.3 92.4 93.6
please refer Table 23. 30 89.6 92.4 93.6
40 90.2 93.0 94.1
Proposed Efficiency Norms (as on Oct – 2007): 50 91.3 93.0 94.5
IEC is in the process of coming up with new sets of Efficiency levels, 60 91.8 93.6 95.0
for both 50 Hz & 60Hz, represented by: 75 91.7 94.1 95.4
Standard Efficiency; represented by – IE1. 100 92.3 94.5 95.4
High Efficiency; represented by – IE2. 125 92.2 94.5 95.4
Premium Efficiency; represented by – IE3. 150 93.0 95.0 95.8
Super Premium Efficiency; represented by – IE4, 200 93.5 95.0 96.2
Size (hp) Pre-EPAct1 EPAct2 NEMA Premium4
More information can be found out, when IEC publishes and re- 250 94.2 95.0 96.2
leases the IEC Standard IEC 60034-30. 300 94.4 95.4 96.2
350 94.6 95.4 96.2
Note: Table 21, indicates the Nominal values being proposed for 400 94.8 95.4 96.2
Premium Efficiency (IE3) levels. The values could get changed when 450 94.9 95.4 96.2
the standard is released, by IEC. 500 94.9 95.8 96.2
1. Pre-Epact: DOE's MotorMaster+ software version 4.00.01
(9/26/2003) "Average Standard Efficiency" motor defaults
2. EPAct: Energy Policy Act of 1992
3. Energy Efficient: NEMA MG 1-2003 Table 12-11
4. NEMA Premium: NEMA MG 1-2003 Table 12-12

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
SIMPLE PAYBACK CALCULATIONS: MOTOR TESTING
The most important factor to decide for replacement of a motor is Good motor application practice requires that uniform and mean-
the pay back period. ingful terminology be used to define efficiency values which are de-
A = per unit Load = (%Load / 100%) termined by accurate test procedures uniformly applied by the
B = Annual usage in terms of No. of hours motor manufacturers.
C = Electricity Cost per kWh in $
Testing to accurately determine the value of motor losses can be
If efficiency of the existing motor = (Effold) in % terms and time consuming and expensive. Also, wide variations in results can
Efficiency of the new motor = (Effnew) in % terms be experienced when different test methods are used. In order to

[ ] ]
100 100 maintain consistency, NEMA has established the following guide-
Savings = Hp x 0.746 x A x B x C x – lines:
(Effold) (Effnew)
Efficiency and losses shall be determined in accordance with the
Cost difference of Motor = (Cost for Premium Eff, Motor) – (Cost for latest revision of IEEE standard 112 or CSA C390. Polyphase squir-
Low Eff. Motor) rel-cage motors rated 1-500 Hp shall be tested by dynamometer.
Where “Cost for Low Eff. Motor” could be; an old running motor =0 The efficiency will be determined using segregated losses in which
10.20
Or Replacement for a failed motor = Cost of Competitor Motor stray load loss is obtained from a linear regression analysis to re-
duce the effect of random errors in the test measurements.
Selection & Application Guide

Pay back (in years) = (Cost difference of Motor) / (Savings)

This procedure focuses on stray load losses where the greatest
To illustrate the benefit Annual Savings for X$D Ultra, over competi- variance can occur from one motor to the next. It also clearly de-
tor motor (considering minimum guaranteed efficiencies- values fines the procedure and requires testing either at full operating tem-
from Table 19); under the following condition: perature or by making corrections for temperature differences.
Finally, the test method requires use of a dynamometer to provide
A = per unit load = 75%/100% = 0.75 the most accurate data as a basis for accuracy improvement and
B = Annual usage = 7200 hours stray load loss measurement.
C = Electricity cost per kWh= 0.09$
Hp = 20 Hp Motor efficiency is not an absolute or constant for all motors of the
Pole = 4 same design. Rather, the efficiencies of a large number of motors

[ ] ]
100 100 will fit a distribution as shown in Figure 19. Though Figure 19 illus-
Savings = 20 x 0.746 x 0.75 x 7200 x 0.09 x – trates a normal distribution, in reality the distribution need not be
91.7 92.4 normal.
Annual Savings = $ 59.90

To illustrate the Pay-back period, to replace a 15 year old running

20Hp 4-Pole motor with a Premium Efficiency motor, under the fol-
lowing operating conditions:

A = per unit load = 75%/100% = 0.75

B = Annual usage = 7300 hours
C = Electricity cost per kWh = 0.09$
If Cost for Premium Eff. Motor = X$D Ultra® Price = $ 1125.00

Refer the following Table 22 above; to compare & note the effi-
ciency level; from which we can arrive at:
Effold = 88.5%
Effnew = 93% The nominal efficiency which appears on the motor nameplate cor-

[ ] ]
100 100 responds to the nominal, or average expected efficiency on the
Savings = 20 x 0.746 x 0.75 x 7300 x 0.09 x – curve. The guaranteed minimum efficiency appearing on GE energy
88.5 93.0 efficient motor nameplates corresponds to the minimum, or guar-
Savings = $ 401.96 anteed on the curve.
Figure 19: Efficiency Distribution
Cost difference of Motor = $ 1125.00-0 = $ 1125.00

Payback in years = $1125.00 / $401.96

= 2.8 years.
A Pay-back Period less than 3 years, is recommended for replacement.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
It is to be noted that there is difference in calculation between Corona Inception Voltage (CIV)
NEMA & IEC, the same is illustrated by the table below: The CIV is the voltage at which partial discharges begin occurring
Table 23: Comparison of methodology for Efficiency calculation be- within small voids inherent in any insulation system, for random
tween IEC and NEMA winding which is fed by IGBT drive. When the voltage stress across
these voids reaches the CIV, a discharge of energy takes place.
Parameters IEC NEMA These partial discharges can cause degradation of the insulation
Standards IEC 60034-2 IEEE-112 Method B system through both chemical and mechanical erosion. Clearly, if a
Rotor I2R loss or No temperature Temperature correction motor is operating continuously at a level of voltage stress above
Slip Loss correction to Winding Temperature its CIV, insulation degradation occurs and eventually leads to motor
Stray load loss 0.5% of Input* Measured ** failure.
Input Measured Measured
Calculated by subtract- Calculated from meas- CIV can be controlled
Output 1. Externally by:
ing the losses from input ured Torque.
• Introducing power conditioning accessories like filters, reactors
* 0.5% of Input; for a Motor & isolation transformers.
0.5% of Output for a Generator • Restricting the distance (lead length), between the motor and
** Calculated Stray loss is smoothed by Regression Analysis; drive.
10.21
Output is corrected.

Selection & Application Guide

2. Internally by:
PLUG REVERSAL TESTING • Eliminating small air spaces where corona could develop.
This is an accelerated life test to evaluate the integrity of the con- • Making the space between conductors sufficiently long, so that
struction & materials for the insulation system of the motor. "Plug- a 2000 volt spike; cannot cause a partial discharge.
ging" is rapid braking of the motor brought about by suddenly • Advanced PWM control techniques are being developed to
reversing two of the three phases of the supply voltage while it is reduce the maximum spike voltage from 3 times to 2 times of
rotating in any direction. This "plugging" action subjects the motor DC voltage.
winding to severe electromagnetic forces and consequent mechan-
ical stresses. Effects of CIV, depend on construction & process adopted during
manufacturing; few are listed below:
The test consists of subjecting the motor to a several thousands of
plugging and reversals. At the end of the test, the motor must be 1. Winding: CIV improves if the beginning turn & ending turn are
operable and successfully pass the standard insulation inspection not in close proximity.
requirements and has exceeded the compiled historical data. Figure
20, shows the Plug-reversal historical data for a 4-pole motor. 2. Varnish & Resin: CIV improves with the increase in number of
‘dip & bake’ or ‘VPI’ system.

3. Phase Paper: Introduction of phase paper between the

different phases, improves CIV, which are a standard feature
for GE’s Poly-phase motors.

AMBIENT
As a standard offering the GE Motors are rated for maximum ambi-
ent of +40 C. For special ambient, refer page no: 32.

GE Stock X$D Ultra ® Motors, generally are rated for Dual Ambient,
as follows:
At ambient 40 deg. C, Class F with temperature rise limited to Class
B at 1.0 Service Factor & suitable for '1.15 Service Factor with Class
F rise'. Alternatively these motors are suitable for operation in a 65
deg. C ambient with Class F rise, at 1.0 Service Factor.
Figure 20: 4-pole GE Motor test results data for Minimum number
of Plug-reversals.

It is to be noted that for the subject test motor is equipped with spe-
cial grease and or bearings. If need arises, the Bearing system of
the test motor, is overhauled.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
POWER FACTOR There are two basic methods for improving the power factor of a
motor for a particular application:
In a sense, motors are electromagnets and power factor is a meas-
ure of the amount of magnetizing current required.
1. Purchase a motor with an inherently high power factor.
Power factor is an important consideration when selecting a motor
2. Install power factor correction capacitors. Capacitors draw
for a particular application since low power factor may result in
leading current as opposed to the lagging current drawn by induc-
power factor penalty charges from the utility company. Power
tion motors. Placing capacitors in parallel with the motor windings
companies must supply KVA but normally meters only kilowatts
will result in leading current offsetting some of the lagging current,
used, low motor power factor requires additional KVA with low re-
increasing power factor as shown in Figure 23:
turn on KW utilized; hence, power factor penalties.

Following is the equation for power factor in a three-phase system:

Watts Input
Amps =
√3 x Volts x PF
10.22
The equation below is a numerical method of expressing the phase
difference between voltage and current in a motor circuit. The cur-
Selection & Application Guide

rent in an induction motor lags the applied voltage, and only the
component that is in phase with the voltage varies with motor
power. The relationship expressed in the above equation can be
shown as a vector relationship in which the numerical expression is
actually the cosine of the angle L.

Figure 23: Power Factor Correction

For many applications the use of capacitors for power factor cor-
rection is the most economical method and one that also works at
Watts Input partial loads. Capacitors should be used to improve full-load power
PF = factor to approximately 95% maximum.
√3 x Volts x Amps

Figure 21 WARNING: IN NO CASE SHOULD POWER FACTOR IMPROVEMENT CA-

PACITORS BE APPLIED IN RATINGS EXCEEDING THE MAXIMUM SAFE
As seen from their relationship, line current required for a given VALUE SPECIFIED BY THE MOTOR MANUFACTURER. EXCESSIVE IM-
motor output varies inversely with power factor. Increasing power PROVEMENT MAY CAUSE OVER EXCITATION RESULTING IN HIGH
factor will reduce required line current, thus reducing voltage drop TRANSIENT VOLTAGES, CURRENTS AND TORQUES THAT CAN IN-
in power lines and transformers. CREASE SAFETY HAZARDS TO PERSON¬NEL AND CAUSE POSSIBLE
DAMAGE TO THE MOTOR OR TO THE DRIVEN EQUIPMENT.
The lagging current shown above is actually motor magnetizing
current, which is dependent upon motor design. This magnetizing
current is independent of motor load; i.e., just as much is required at
LOAD CONNECTION
no-load as at full-load. Thus power factor at partial loads is never as
high as at full-load, and at no-load power factor is essentially zero. TYPES OF CONNECTION
Two methods of mechanical connection of the motor to the driven
load are commonly used:

1. Direct Connection
Direct connection should always be considered where the required
load speed coincides with an available motor speed. The preferred
practice is to use a flexible coupling, which will allow a slight
amount of misalignment and minimize transmission of thrust to the
motor bearings. Axial thrust loads are commonly encountered
when a pump impeller or fan is mounted on the motor shaft. They
Figure 22 also occur in direct connected helical gear drives and when the
motor is mounted vertically or in an inclined position where any
weight other than the rotor is supported by the motor shaft. Refer
to Table 24 for recommended maximum axial thrust loads for hori-
zontal ball-bearing motors with typical bearing sizes.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
2. Belt, chain and gear drives Table 25: Limiting Sheave Dimensions for V-Belt Drive
When connecting a motor to its load with this type of drive, proper (Frames 182T – 449T)
selection is necessary to limit bearing loads within radial load ca-
V-belt Sheave (inches)**
pacities. Tables 25 and 25A provide recommended minimum V-belt
Horsepower at Conventional Narrow
sheave diameters for 60 and 50 Hz motors. Tables 24 and 24A indi- Frame
Sync Speed, RPM A, B, C, and D
cate the approximate radial forces corresponding to a belt tight- 3V, 5V, 8V sections***
sections ††
ened sufficiently to prevent slippage. Additional tension will Max
Max
Belt pull
Min. Pitch Min out- width
increase the radial force and decrease bearing life. For A-B-C-D-E 60 Hz 3600 1800 1200 900
dia
width
side dia. inches
(lbs)*
inches  *
belts, the center line of the pulley should not extend beyond the #

end of the shaft. For 3V-5V-8V belts, the centerline of the pulley 182T 3 3 1.5 1 2.4 5.25 2.4 2.75 155
182T 5 - - - 2.6 5.25 2.4 2.75 130
should not be any closer to the end of the shaft than 1/2 the V di-
184T - - 2 1.5 2.4 5.25 2.4 2.75 155
mension of the shaft.
184T 5 - - - 2.6 5.25 2.4 2.75 130
184T 7.5 5 - - 3.0 5.25 3.0 2.75 210
At times requests are made for parameters not labeled in these ta-
213T 7.5-10 7.5 3 2 3.0 6.5 3.0 3.38 310
bles. Belt and sheave manufacturers and their distributors typically 215T 10 - 5 3 3.0 6.5 3.0 3.38 310
provide a Load Analysis Data Sheet as a technical service. Regard- 215T 15 10 - - 3.0 6.5 3.8 3.38 355
10.23
less of who is asked, the following information is necessary. 254T 15 - 7.5 5 3.8 7.75 3.8 4.0 370
254T 20 15 - - 4.4 7.75 4.4 4.0 425
Table 24: Axial Thrust (pounds) for Horizontal Motors

Selection & Application Guide

256T 20-25 - 10 7.5 4.4 7.75 4.4 4.0 425
256T - 20 - - 4.6 7.75 4.4 4.0 565
3600 RPM 1800 RPM 1200 RPM 900 RPM
Frame 284T 30 - - - 4.4 9.0 4.4 4.58 425
Brg Thrust Brg Thrust Brg Thrust Brg Thrust 284T - - 15 10 4.6 9.0 4.4 4.58 625
182-184 6206 140 6206 165 6206 220 6206 245 284T - 25 - - 5.0 9.0 4.4 4.58 705

213-215 6307 250 6307 335 6307 375 6307 425 286T 30 - - - 4.4 9.0 4.4 4.58 425
286T 40 - - - 4.6 9.0 4.6 4.58 540
254-256 6309 405 6309 500 6309 670 6309 710
286T - 30 20 15 5.4 9.0 5.2 4.58 715
284-286 6310 460 6310 625 6310 770 6310 790
324T 40 - - - 4.6 10.25 4.6 5.25 540
324-326 6210 230 6210 290 6210 395 6210 325
324T - 40 25 20 6.0 10.25 6.0 5.25 825
364-365 6213 390 6213 485 6213 630 6213 635 324T 50 - - - 5.0 10.25 5.0 5.25 620
404-405 6313 375 6213 435 6213 590 6213 710 326T 50 - - - 5.0 10.25 5.0 5.25 620
444-445 6314 760 6314 1040 6314 1205 6314 1400 326T - 50 30 25 6.8 10.25 6.8 5.25 910
449 6314 705 6314 965 6314 1115 6314 1325 326T 60 - - - 5.4 10.25 5.4 5.25 690
509 6315 705 6318 1175 6318 1275 6318 1445 364T - - 40 30 6.8 11.5 6.8 5.88 1195
511 6315 680 6318 1030 6318 1290 6318 1260 364T 60 - - - 5.4 11.5 5.4 5.88 690
513 6315 620 6320 1265 6320 1360 6320 1450 364T - 60 - - 7.4 11.5 7.4 5.88 1005
365T - - 50 40 8.2 11.5 8.2 5.88 1210
NOTE: Table 24 assumes no external radial loading on the shaft. 365T - 75 - - 9.0 11.5 8.6 5.88 1080
Thrust values in Table 24 represent the maximum permissible to 404T - - 60 - 9.0 14.25 8.0 7.25 1395
provide a 25,000 hour L10 life in accordance with AFBMA calcula- 404T - - - 50 9.0 14.5 8.4 7.25 1475

tions. 404T - 100 - - 10.0 14.25 8.6 7.25 1440

405T - - 75 60 10.0 14.25 10.0 7.25 1485
405T - 100 - - 10.0 14.25 8.6 7.25 1440
405T - 125 - - 11.5 14.25 10.5 7.25 1475
444T - - 100 - 11.0 16.75 10.0 8.5 1770
444T - - - 75 10.5 16.75 9.5 8.5 1995
444T - 125 - - 11.0 16.75 9.5 8.5 1630
444T - 150 - - - - 10.5 8.5 1770
445T - - 125 - 12.5 16.75 12.0 8.5 1935
445T - - - 100 12.5 16.75 12.0 8.5 2065
445T - 150 - - - - 10.5 8.5 1770
445T - 200 - - - - 13.2 8.5 1875
445T - - 150 - - - 13.5 8.5 2065
449T - - 200 - - - 18.75 8.5 1980
449T - - - 150 - - 19.0 8.5 1955
449T - - - 200 - - 27.75 8.5 1785
449T - 250 - - - - 15.5 12.75 1995

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
*For the maximum speed of the drive components, see NEMA MG- Table 25A: Limiting Sheave Dimensions for V-Belt Drive
1-2006 Section 14.7.3. Typical 500 Frame Data
†For the assignment of horsepower and speed ratings to frames,
see NEMA Part 13. Dripproff
**Sheave dimensions are based on the following: Horsepower @ RPM Min. Sheeve Belt Pulls
Brg. Const.
a. Motor nameplate horsepower and speed 1800 1200 900 Dia. (in) (lbs)
b. Belt service factor of 1.6 with belts tightened to belt
- - 150 (1) 16.5 2200
manufacturers’ recommendations
c. Speed reduction of 5:1 - - 200 (2) 9 5500
d. Mounting of sheave on motor shaft in accordance with - - 250 (2) 17 3600
NEMA MG-1-2006 Section 14.7 - 250 - (2) 9 5200
e. Center-to-center distance between sheaves approximately - 300 - (2) 15 3700
equal to the diameter of the larger sheave 300 - - (2) 7.5 4900
f. Calculations based upon standards covered by the †† and
350 - - (2) 13.5 3200
*** footnotes, as applicable
TEFC Motors
10.24 The width of the sheave shall be not greater than that required to
- - 125 (1) 14.5 2100
transmit the indicated horsepower but in no case shall it be wider
than 2(N-W) - 0.25. - - 150 (1) 18 2100
Selection & Application Guide

- - - (2) 13 3800
*** As covered by Standard Specifications for Drives Using Narrow - 200 - (1) 18 2100
V-Belts (3V, 5V, and 8V). - 250 - (2) 15 3100
- 250* - (2) 10.5 4400
#The width of the sheave shall be not greater than that required to
250 - - (1) 17.5 1800
transmit the indicated horsepower but in no case shall it be wider
than (N-W). 300 - - (2) 9 4100
350 - - (2) 11.5 3800
††As covered by Engineering Standards Specifications for Drives
Using Multiple V-Belts (A, B, C, and D Cross Sections)
See 1.1, The Rubber Manufacturers Association. * for 5011L frame size.
(1) Deep groove ball-bearing construction
(2) Special shaft materials and roller-bearing construction.

NOTE: 1. Minimum bearing life, L10, for a given sheave diameter is

25,000 hours.
2. The recommended sheave diameters are based on a 5:1
speed reduction and a sheave center-to-center distance
approximately equal to the diameter of the larger sheave.

CAUTION: BELT SPEEDS IN EXCESS OF 6500 FEET PER MINUTE MAY

REQUIRE SPECIAL SELECTION OF DRIVE COMPONENTS. MOTOR USER
SHOULD GET SPECIFIC APPROVAL FROM BELT AND SHEAVE SUP-
PLIER FOR SUCH APPLICATIONS.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
LOAD CALCULATIONS
Belt Driven Application Analysis
Belt and Sheave Manufacturers and their Distributors typically provide a Load Analysis Data Output Sheet to the end user/OEM as a techni-
cal service. When requesting a quotation for GE Industrial Systems we suggest that the Load Analysis Data Output Sheet be provided in ad-
dition to this form for a complete motor shaft and bearing analysis.

10.25

Selection & Application Guide

End User:
Application Information (e.g. fan, pump, crusher):
Type of Driven Load (e.g. variable torque, constant torque, constant horsepower):

Motor Rating - Required

Horsepower: Frame size: Speed:
Motor Enclosure: Voltage:
Shaft Orientation (e.g. horizontal, vertical shaft up, vertical shaft down):

Belt Information - Required

Distance between face of motor endshield and center line of motor sheave width (L):
Inertia of driven load referred to the motor shaft (lb - ft2) (Required for centrifuge):

The following is not required when a Load Analysis Data Output Sheet is provided:
Option A
Motor sheave pitch diameter (Dm):
Driven sheave pitch diameter (Dl):
Center-to-center distance between sheaves (C-C):
Motor height vs. driven shaft (H):
Width of motor sheave (W):
Weight of motor sheave (lbs):
Belt service factor:
Belt Type (e.g. 5V, 3VX): Number of belts:

Option B
Radial Load/Belt Pull (lbs):

This page must be completed for:

a) 720 rpm and slower motors (10 or more poles)
b) 447T and larger frame sizes
c) Non-standard L10 values
d Customer requests

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
ELECTRICAL CONSTRUCTION 3. Autotransformer Starting
In contrast to part winding start, autotransformer starting uses the
complete motor winding but limits input voltage to reduce inrush
WINDING CONNECTIONS AND STARTING current. The most commonly furnished taps on autotransformer
The design of a motor’s windings and the pattern of connecting the starters are 50, 65 and 80% of full voltage and most also provide an
leads from these windings will determine voltage ratios for dual- adjustable timer for switching to full voltage after the motor has ac-
voltage motors and may also determine what starting options are celerated. No special motor winding is required.
available.
Table 26: Autotransformer Starter
Following is a brief description of some of the more popular starting
% Full Load Value
methods:
Voltage & Cur- Supply Line Cur- Motor Output
Transformer Tap
1. Full Voltage Starting rent at Motor rent Torque
This method is the least expensive from an initial cost standpoint 80% Tap 80 64* 64
and is the most commonly used starting method on smaller motors. 65% Tap 65 42* 42
While it results in the highest inrush current values, connections and 50% Tap 50 25* 25
10.26 starter operation are greatly simplified. All standard motors are de- * Autotransformer magnetizing current not included. Magnetizing
signed for full voltage (across-the-line) starting. current is usually less than 25 percent of motor full-load current.
Selection & Application Guide

4. Wye Start/Delta Run

This connection method allows a motor to be started at reduced
load with reduced phase voltage and, therefore, with reduced in-
rush current. Wye Delta starters may be furnished with either open
or closed transitions. Open transition, while generally lower in cost,
will produce higher transient current than a closed transition starter
at the transition from wye to delta.

Figure 24: Full Voltage Starting / Direct –On-Line (DOL) Starting

2. Part Winding Starting (PWS)

This method energizes only part of the total winding when the
motor is started and is suitable for pump, fan and compressor
loads. PWS will reduce inrush current, but the motor heating rate
will increase considerably. There are no standard performance re-
quirements for part winding starting and, therefore, a motor started
in this manner may fail to accelerate a high-inertia or constant
torque load. PWS usually requires special winding connections,
which must be specified at the time the motor is ordered.

Figure 26: Wye Start / Delta Run

Figure 25: Part Winding Start

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
MECHANICAL CONSTRUCTION DRAINS AND BREATHERS

Enclosed Motors (except explosion-proof)

FRAME DESIGNATION SYSTEM: Standard enclosed motor construction includes drain holes in the
For Footed machines, in NEMA the first 2 digits are taken & divided bottom of the motor. On X$D Ultra® severe-duty motors, special
by 4, the resultant value indicates the height of the shaft centre plugs designed to serve as both drains and breathers are inserted
from the ground in inches. into the drain holes. Available as an option is a sintered-metal
For a quick historical reference on how NEMA frame size, was re- breather and drain which acts as a one-way vent preventing en-
duced over the years can be found at Page no: 39 (on ANNEXURE B). trance of contami¬nants while allowing the moisture to drain out.
For example NEMA Frame 182; has a shaft center height of
18/4=4.5”. Explosion-Proof
Standard explosion-proof motors are furnished without drains or
For Foot-mounted machines, the IEC frame designation system breathers. Available as an option is the UL listed Crouse-Hinds
consists of the frame number that indicates the height of the shaft breather/drain which acts as a one-way vent, preventing the en-
centre from the ground in millimeters (mm). trance of contaminants while allowing moisture to drain out of the
For example IEC Frame 112S; has a shaft center height of 112 mm. motor. 10.27
In the Table 27: S, M & L are variations in B (i.e. equivalent to NEMA
2F) dimension; refer to IEC 60072-1 for more details. MOUNTING CONFIGURATIONS

Selection & Application Guide

The following diagrams illustrate the various mounting possibilities
Table 27: Comparison of NEMA & IEC Frame Designations
for “horizontal” motors in NEMA & IEC.
IEC 90S 90L 112S 112M 132S 132M 160M 160L 180M 180L
NEMA 143 145 182 184 213 215 254 256 284 286

IEC 200M 200L 225S 225M 250S 250M 280S 280M 315S 315M
NEMA 324 326 364 365 404 405 444 445 504 505
Additional quick references for major mounting dimension between
NEMA and IEC can be found on Page No: 29 (ANNEXURE A).

ENCLOSURE MATERIAL
Frame and endshield materials are listed below in Table 28.
Table 28
Frame Size Enclosure Frame & Endshield Material
143-449 TE Cast iron or rolled steel
143-449 DP, WPI Cast iron or rolled steel
509-5013 DP, TEFC, WPI, WPII Cast iron
182-5013 Explosion-proof Cast iron
143-5013 Severe-duty Cast iron
*TE : Totally enclosed machines like TENV, TEFC, TEAO, TEBC as ap-
plicable .
Table 29: Quick Comparison of NEMA & IEC Enclosure/Cooling
Designation
IEC Enclosures
NEMA Enclosures
Protection Cooling
DPFG Dripproof fully guarded, self ventilated IP-22 IC-01
ESV Piped Ventilation (Enclosed separately IP44 IC-37
ventilated, air ducted in and out)
TENV Totally enclosed non-ventilated IP44 IC-410
TEFC Totally enclosed fan cooled IP44 IC-411
TEAO Totally enclosed air over frame IP44 IC-416
TEBC Totally enclosed blower cooled IP44 IC-416

TENV-XP TENV, explosion proof

Not defined
TEFC-XP TEFC, explosion proof

Figure 27: NEMA Mounting

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
Table 30: Comparison of Mounting configurations between IEC &
NEMA
Arrangement NEMA MOUNTING IEC MOUNTING*
Floor Mounting F1,F2 IM B3/IM 1001
Ceiling Mounting C1,C2 IM B8/IM 1071
Wall Mounting, W2,W4 IM B6/ IM 1051
Shaft Horizontal W1,W3 IM B7/IM 1061
Wall Mounting, W6,W7 IM V5/IM 1011
Shaft Vertical W5,W8 IM V6/IM 1031
* Terminal box location as per IEC 60034-7 Refer section 3.5

DYNAMIC BALANCE
General Electric motors are dynamically balanced so that vibration,
as tested per NEMA standard MG-1-12.08, will be within the limits
stated below for standard balance. Motors balanced to either the
10.28
special or precision balance limits shown will be furnished at addi-
tional price when specified. Precision balance is a feature of the X$D
Selection & Application Guide

Ultra® severe-duty product line.

Table 31: Vibration Limits (182-5013 Frame)

Motors with two ball bearings

Vibration measured in Inches/Sec
RPM Standard Special Precision X$D-Ultra®
All speeds 0.15 0.075 0.055 0.04
Motors with one ball bearing and one roller bearing
Vibration measured in Inches (peak to peak)
RPM Standard Special Precision
3000-4000 0.0010 0.0005 0.0003
1500-2999 0.0015 0.0008 0.0004
1000-1499 0.0020 0.0010 0.0005
999 and slower 0.0025 0.0013 0.0007

Figure 28: IEC mounting

Motors may be furnished for any of the twelve mounting configura-

tions shown in Figure 23. Other than F1 and F2 mountings, end-
shields need to be rotated appropriately; to ensure guarding, drain
and grease inlet/outlet locations.

Unless otherwise specified, all horizontal motors will be furnished

for F1 mounting.

Vertical Mounting
Ball bearing motors in frames 326 and smaller mounted vertically
with shaft up or down can handle external thrust loads, in either di-
rection, not exceeding the thrust value shown in Table 24. Larger
motors require a special lubrication system which can be furnished
on request. Motors which are to be mounted vertically must be
specified shaft up or down to obtain a suitable bearing and lubrica-
tion system.

Figure 29: Shows the position of Cast-in Vibration Pads, on

Standard X$D Ultra® Motors

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Benefits of Lower vibration: Table 32: Re-lubrication Intervals
Machinery Vibration is significant contributor for equipment failure.
To build reliable equipment it is advisable to use motors with lower Relubrication interval
vibrations. GE’s X$D Ultra® Vibration at rated voltage and fre- Type of Typical Hp (yrs)
quency shall not exceed the limits of ‘0.04 inch per second’. Overall Service Examples Range
Horizontal Vertical
vibration as evaluated by NEMA MG 1-12.07. The design of the X$D
Easy Valves, door 1.0-7.5 10 9
Ultra® meets such stringent industry specifications for vibration as openers, portable
GM 7E-TA for T-frame motors. 10-40 7 3
floor sanders,
motor operating 50-150 4 1.5
Following can be the advantages of using motors with lower vibra- infrequently (one
200-350 3 9 Mo.
tion: hour per day)
• Longer bearing life 400-800 1 –
• Reduced damage to the shafts and rotor Standard Machine tools, air 1.0-7.5 7 3
• Fewer equipment break-down conditioning ap-
10-40 4 1
• Lower operational noise paratus, convey-
• Minimum power loss hence efficient operation of equipment ors, one or two 50-150 1.5 6 Mo.
shifts, garage 10.29
• Low energy costs 200-350 1 3 Mo
compressors, re-
• Minimum stress levels in the equipment structures frigeration ma- 400-800 6 Mo. –

Selection & Application Guide

For additional information, refer IEEE Paper PCIC-2003-12 chinery, laundry
machinery, oil
BEARING SYSTEMS well pumps,
wood working
machinery
Antifriction
All standard motors are equipped with “clean steel” Conrad deep- Severe Motors for fans, 1.0-7.5 4 1.5
groove-type ball bearings, sized for the loads to be expected in in- M-G sets, etc.
10-40 1.5 6 Mo.
dustrial applications. that run for 24
hours/365 days, 50-150 9 Mo. 3 Mo.
coal and mining
Sleeve-Type 200-350 6 Mo. 1.5 Mo.
machinery, mo-
Split-sleeve bearings are available for frames 509 through 5013 in tors subject to 400-800 3 Mo. –
dripproof and Weather Protected I and II enclosures. They should be severe vibration,
used for direct drive applications only. These bearings are mounted steel mill machin-
in the bottom and top halves of the split endshields. The top half ery
endshield is removable for bearing or winding inspection. Very Severe Dirty, vibrating 1.0-7.5 9 Mo. 6 Mo.
Solid sleeve bearings are available for frames 509 through 5013 to- applications,
10-40 4 Mo. 3 Mo.
tally-enclosed fan-cooled machines. Sleeve bearings are not avail- where end of
able on explosion-proof motors. shaft is hot 50-150 4 Mo. 2 Mo.
All sleeve bearings are equipped with oil reservoirs, ring oilers, sight (pumps and fans),
200-350 3 Mo. 1 Mo.
high ambient
gauges, level gauges and drain provisions. 400-800 2 Mo. –
temperatures

BEARING LUBRICATION
Ball bearing motors are shipped with sufficient grease for a long op- ENVIRONMENTAL CONSIDERATIONS
erating period. Re-lubrication at intervals consistent with the type of
service shown in the following table will provide longer bearing life. MOTOR ENCLOSURES
Excessive, too frequent lubrication or the use of non-compatible lu- The type of enclosure required is dependent upon the surrounding
brication may damage the motor. If the bearing grease cavity and atmosphere in which the motor is installed and the amount of me-
the bearing races have excessive grease to the point where the chanical protection and corrosion resistance required. The two gen-
grease stays packed around the bearing rotating elements, the eral classes of motor enclosure are open and totally-enclosed. An
bearing will actually run hotter. Follow re-lubrication type and use open machine is one having ventilating openings which permit pas-
procedures provided in the instructions shipped with motors. sage of external air over and around the winding of the motor. A to-
tally-enclosed machine is constructed to prevent the free exchange
of air between the inside and outside of the motor, but not suffi-
ciently enclosed to be termed air-tight.

Derivatives of these two basic enclosures are described below.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
Dripproof Piped Ventilation
Dripproof motors are designed to be internally ventilated by ambi- When motors are cooled by piping in outside air, the required air-
ent air, having ventilation openings constructed so that successful flow in cubic feet per minute (CFM) can be calculated from the
operation is not affected when drops of liquid or solid particles equation:

[ ] ]
strike the enclosure at any angle from 0 to 15 degrees downward
from vertical. Dripproof motors are typically used in relatively clean, 100
CFM= Hp -1 746x1.8
indoor applications. Eff %

Weather Protected Type I (WPI) 10

A weather protected type I machine is an open machine with its
ventilating passages so constructed as to minimize the entrance of This results in a 10 ºC air temperature rise.
rain, snow and airborne particles to the electric parts and having its
ventilating openings so constructed as to prevent the passage of a HAZARDOUS (CLASSIFIED) LOCATIONS
cylindrical rod 3/4-inch in diameter. Specially designed totally-enclosed motors are available for opera-
tion in the classes of hazardous atmospheres, as defined by Under-
10.30
Weather Protected Type II (WPII) writers Laboratories, the National Electrical Manufacturers
A weather protected type II machine shall have, in addition to the Association and the National Electrical Code. Two basic classes are:
enclosure defined for a weather protected type I machine, ventilat-
Selection & Application Guide

ing passages at both intake and discharge so arranged that high- Class I Explosion-Proof
velocity air and airborne particles blown into the machine by An explosion-proof motor is a totally-enclosed machine designed to
storms or high winds can be discharged without entering the inter- withstand an explosion of a specified gas or vapor which may
nal ventilating passages leading directly to the electric parts of the occur within it and to prevent the ignition of the specified gas or
machine itself. For motors in frames 143T through 449T, standard vapor surrounding the motor.
TEFC motors should be specified. Ratings built in frames 509 and
larger utilize dripproof frames with “top hat” mechanical construc- Class II Dust-Ignition Proof
tion to meet the above specifications. WPII motors have provisions
A dust-ignition proof motor is a totally-enclosed machine con-
for air filters.
structed in a manner which will exclude ignitable amounts of dust
or amounts which might affect performance or rating, and which
Totally-Enclosed will not permit arcs, sparks or heat generated inside the enclosure
Totally-enclosed motors are designed so that there is no free ex- to cause ignition of exterior accumulations or atmospheric suspen-
change of air between the inside and the outside of the enclosure, sion of a specific dust and/or in the vicinity of the enclosure.
but not sufficiently enclosed to be airtight. Totally-enclosed motors The various atmospheres defined within the two classes have been
may be of following types of construction. divided into groups dependent upon the explosive characteristics of
the materials. The class and group of service shall appear on the
1. TEFC (Totally-Enclosed Fan-Cooled) This type includes an motor nameplate along with an identification number which identi-
external fan mounted on the motor shaft. This fan is enclosed in fies a maximum operating temperature as shown in the following
a fan casing which both protects the fan and directs the output tabulations:
air over the motor frame for cooling. The airflow is dependent
on the shaft speed. Table 33: Hazardous Atmospheres
Class Group ID No. Atmosphere
2. TEAO (Totally-Enclosed Air-Over) This type is similar to TEFC de
I A T2A Acetylene
signs except that the cooling air being forced over the motor
I B T2A Hydrogen, manufactured gas
frame is provided by a fan which is not an integral part of the
I C T3C Ethyl ether vapor
motor. User should ensure the sufficient airflow as mentioned
I D T2A Gasoline, petroleum, naptha, alcohols,
on the nameplate.
acetone, lacquer solvents, natural gas
T2D*
3. TENV (Totally-Enclosed Non-Ventilated) This type of construction
II E T3B Metal Dust
does not require forced airflow over the motor frame for
II F T3B Carbon black, coal or coke dust
cooling.
II G T3B Grain Dust
4. TEBC (Totally-Enclosed Blower Cooled) is used in applications *T2A without thermostat/T2D with thermostat
where a separate mounted blower provides supplementary air
to cool the motor. Typical uses are in inverter drive application
with low frequency. The airflow is independent of the shaft
speed.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Table 34: Temperature Identification Numbers operation of machinery or equipment might cause such
Maximum Temperature explosive or ignitable mixtures to be produced, and might also
Identification No. provide a source of ignition through simultaneous failure of
Degrees C Degrees F
electric equipment, operation of protection devices, or from
450 842 T1 other causes; or (3) in which combustible dusts of an electrically
300 572 T2 conductive nature may be present. Division 1 locations always
280 536 T2A require the application of the appropriate dust-ignition proof
260 500 T2B motor.
230 446 T2C
215 419 T2D d) Class II, Division 2 – A Class II, Division 2 location is a location: (1)
200 392 T3 in which combustible dust will not normally be in suspension in
180 356 T3A the air in quantities sufficient to produce explosive or ignitable
165 329 T3B mixtures, and dust accumulations are normally insufficient to
160 320 T3C interfere with the normal operation of electrical equipment or
135 275 T4 other apparatus, or (2) dust may be in suspension in the air as a
120 248 T48 result of infrequent malfunctioning of handling or processing
100 212 T5 10.31
equipment, and dust accumulations resulting there from may
85 185 T6 be ignitable by abnormal operation or failure of electrical

Selection & Application Guide

NOTE: For motors having multiple UL labels, the lowest identification equipment or other apparatus. The National Electrical Code
number will apply. specifies Class II, Division 2 motors have no external openings
and comply with external surface temperature limits when
Divisions, Hazardous Location operating at full-load in free air. The surface temperature limits
The National Electrical Code has defined two distinct divisions vary with dust characteristics such as ignition temperature,
within each of the hazardous location classes: susceptibility to dehydration and potential for carbonization.
The controlling document is ANSI/NFPA 70; material
a) Class I, Division 1 – A Class I, Division 1 location is a location: (1) characteristics are detailed in NFPA 497M.
in which ignitable concentrations of flammable gases or vapors
exist under normal operating conditions; or (2) in which ignitable e) ATEX Zone 2, Group II, Category 3
concentrations of such gases or vapors may exist frequently be In all European Union Member States, the product which is
cause of repair or maintenance operations or because of intended for use in potentially explosive atmospheres will need
leakage; or (3) in which breakdown or faulty operation of to comply with the ATEX Directive 94/9/EC and the CE Marking
equipment or processes might release ignitable concentrations Directive. This product is governed by European standard
of flammable gases or vapors, and might also cause EN60079-15.
simultaneous failure of electric equipment. Division 1 locations
always require the use of explosion-proof construction motors. Equipment in this category is intended for use in areas in which
explosive atmospheres caused by gases, vapors, mists, or
b) Class I, Division 2 – A Class I, Division 2 location is a location: (1) air/dust mixtures are unlikely to occur or, if they do occur, are
in which volatile flammable liquids or flammable gases are likely to do so only infrequently and for a short period only.
handled, processed, or used, but in which the liquids, vapors, or
gases will normally be confined within closed containers or Equipment in this category ensures the requisite level of
closed systems from which they can escape only in case of protection during normal operation
accidental rupture or breakdown of such containers or systems,
or in case of abnormal operation of equipment; or (2) in which CAUTION: THE RESPONSIBILITY OF SPECIFYING THE PROPER CLASS,
ignitable concentrations of gases or vapors are normally GROUP AND DIVISION OF HAZARDOUS LOCATION RESIDES WITH
prevented by positive mechanical ventilation, and which might THE ULTIMATE USER AND THE INVOLVED REGULATORY AGENCY.
become hazardous through failure or abnormal operation of the
ventilating equipment; or (3) that is adjacent to a Class I, Division Motors for Hazardous (Explosive Gas) Atmosphere, per ATEX:
1 location, and to which ignitable concentrations of gases or IEC standards dealing with apparatus for use in explosive gas
vapors might occasionally be communicated. The National atmospheres are contained in a series of publication 79-0 through
Electrical Code allows the installation of non-explosion-proof 79-19 [24]. The rules for classification and application of motors
motors in Division 2 locations. in these areas differ considerably from United States standards
and practices. Some of the differences are noted in the following
c) Class II, Division 1 – A Class II, Division 1 location is a location: (1) summary.
in which combustible dust is in the air under normal operating
conditions in quantities sufficient to produce explosive or
ignitable mixtures; or (2) where mechanical failure or abnormal

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
Classification of Gases: Dip and Bake (Random Wound 320-5013)
IEC classifies apparatus in two broad groups as follows: In this process preheated winding is slowly dipped in the varnish or
Group 1: for application on coal mining, and resin. After certain time, the winding is removed from the varnish
Group 2: for application in other industries. tank, excess varnish is allowed to drip and cured.
Table 36: Quick winding treatment comparision
Group 2 is divided into categories 1,2 and 3.
for Random Wound motors
‘Category 1 equipment’ is intended for use in Zone O situations.
‘Category 2 equipment’ is intended for use in Zone 1 situations. Winding Dip & Bake Vacuum Trickle
‘Category 3 equipment’ is intended for use in Zone 2 situations. Treatment Pressure Treatment
Impregnation
Classification of Hazardous Areas Penetration Good Better Best
IEC divides the classification of hazardous areas into three zones
Advantages • Cost Best Penetra- • Faster
according to the degree of hazard, defined as follows.
Beneficial tion Process time
Zone 0 - A zone in which an explosive gas-air mixture is
• Low • Efficient
continuously present or present for long periods.
Investment Material
Zone 1 - A zone in which an explosive gas-air mixture is likely to
10.32 Usage
occur in normal operation.
Zone 2 - A zone in which an explosive gas-air mixture is not likely to Limitations • Unwanted • High ---
Selection & Application Guide

occur, and if it occurs it will only exist for a short time. Parts exposed Investment
to Varnish • Longer
Thus the following comparison table 35 applies: • Material Process time
Wastage
Table 35
ATEX UL / NEC
Abrasion Resistance (320-5013)
Group II, Zone 0 Not defined GE motors can be supplied with an abrasion resistant winding
Group II, Zone 1 Class I, Division 1 treatment which gives added protection from airborne particles.
Group II, Zone 2 Class I, Division 2
NOTE: IEC has established six temperature classes for the grouping
of gases relative to the ignition temperature - T1, T2, T3, T4, T5 & T6,
for the surface temperature values of this code please refer Table
34.

WINDING TREATMENT
Various winding treatment options and protective coatings are
available to provide additional protection in special or extreme ap-
plication and environmental conditions.

Custom Polyseal® Motors (Frames 444-5013)

These motors are available with vacuum pressure impregnated
windings which have been taped to hold additional varnish and to
increase their mechanical strength. Custom Polyseal® motors meet
NEMA MG-1-1.27.2 and are capable of an underwater submergence
test which includes a hipot and megger test.

Trickle Treat (Random Wound – 143-449 frames)

In this process while a 60 Hz current is passed through the winding.
This “pumps” the varnish into the windings resulting in better pene-
tration into the stator slots and an increase in varnish build.
Applying a current to the windings cures the varnish. This cures the
windings from the inside-out, rather than oven baking.

Vacuum Pressure Impregnation (449HO & 500 frames)

This process completely seals the windings against moisture and
harsh environment. It provides greater mechanical strength; that
lowers the vibration level. Machine lasts longer and requires less
maintenance.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
MODEL NUMBER NOMENCLATURE Table 37
The following nomenclature is the basis for the majority of GE inte- TENV or Explosion
DP TEFC WPII
gral-hp motor model numbers. The model number format shown TEAO Proof
below provides basic descriptive information as follows: Footed frame and no
customer mounting
Model: 5 K 215 A L 205 A E A B H C E
rabbets or auxiliary
Description: 1 2 3 4 5 6 7 8 devices such as brakes
1. The numeral “5” is used to designate rotating electrical ma- Round frame and no
chinery auxiliary devices such D F W G –
as brakes
2. Electrical Type Letters All others J K K R E
a. PolyPhase:

K NEMA designs A & B 5. Second form letter

KAF Adjustable frequency L Aluminum horizontal 10.33
KE NEMA design A & B complying with Federal Energy Act N Cast iron horizontal, all 500 frames and 449 Explosion
KG NEMA design C

Selection & Application Guide

proof.
KGS NEMA design C Energy Saver S Cast iron horizontal, 320-449 frame
KOF Oil well pump (for single horsepower – (obsolete)) T Cast iron vertical P-base 320-449 frame
KR NEMA design D, 5 to 8% slip or 8 to 13% slip AA Horizontal – 320-449 XSD-ULTRA
KS NEMA design A & B Energy Saver AB Horizontal Cast Iron Frame – 140-280 frame
KOW Triple horsepower, 5 to 8% slip, NEMA D AC Vertical Cast Iron Frame – 140-280 frame
KB Crusher duty, normal efficiency LW Aluminum Water Cooled Frame
KBS Crusher duty, Energy $aver SH Cast Iron Frame 449 High Output (449 HO)
KD Mill duty motors
6. Form numbers
b. Single-Phase:
For Horizontal , the form numbers are as below (Table 38):
KC Capacitor start and Capacitor Start/Capacitor Run Table 38
KCR Capacitor Start/Capacitor Run
3. NEMA frame size 2 pole 4 pole 6 pole
4. First form letter 101-199 201-299 301-399
a. Group 1. The following take precedence over all Group 2 let- 1001-199 2001-2999 3001-3999
ters (except explosion-proof) 5001-5999 6001-6999 7001-7999
L - Severe Duty non-X$D Type KS and KGS models 10001-19999 20001-29999 30001-39999
M Marine motors 8 pole 10 pole 12 pole
P Partial motors
S Severe-duty motors 401-499 501-599 601-699
X Horizontal X$D 841/Vertical 841 Motors 4001-4999 50001-59999 60001-69999
8001-8999
Note : Letters M, P and X all take precedence over the letters L and S 40001-49999
b. Group 2. Are shown in Table 37. 14 pole 16 pole
701-799 801-899
70001-79999 80001-89999

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
For Vertical motors, the form numbers are as below (Table 39): ELECTRICAL MODIFICATIONS
Table 39
CABLE GLANDS
Construction 2 pole 4 pole 6 pole Cable gland is used to provide weather proof of a single round
multi-conductor cable in to the motor conduit box. Customer must
101-199 201-299 301-399 supply cable outer diameter. Cable size is limited from .25 to 3.5
VSS-NT
1001-1999 2001-2999 3001-3999 inch Diameter for both unarmored and armored cable glands.
VSS-HT 5401-5699 6401-6699 7401-7699
VHS-HT 5001-5399 6001-6399 7001-7399 CURRENT TRANSFORMER
VSS-IL 5701-5999 6701-6999 7701-7999 It is sometimes desirable on larger motors to have current trans-
formers installed in the motor conduit box for operation of auxiliary
devices or sensing circuits. Motors in frames 509-5013 can be fur-
Construction 8 pole 10 pole 12 pole 14 pole 16 pole nished with single-secondary current transformers in the main or
neutral leads. These can include window-type transformers or bar-
401-499 type transformers to meet the specifications of the user or the con-
10.34 VSS-NT 4001- 501- 601- 701- 801- trol manufacturer and must be fully specified by the customer.
4999 599 699 799 899 Current transformers require an oversize conduit box which must
be included in the order.
Selection & Application Guide

8401-
VSS-HT
8699
8001- GROUNDING PROVISIONS
VHS-HT
8399 Special grounding provisions can be supplied in the conduit box or
8701- for mounting in the drive end endshield.
VSS-IL
8999 The special conduit box grounding provision consists of a brass
stud in place of one of the conduit box mounting screws. Also in-
VSS-NT : Vertical Solid shaft Normal thrust cluded are two jam nuts for mounting to an external ground lead.
VSS-HT : Vertical Solid shaft High Thrust Hardware for the endshield grounding option is shipped as a kit in-
VHS-HT : Vertical Hollow shaft High Thrust cluding a brass stud, nut and washer. The stud is assembled in
VSS-IL : Vertical Solid Shaft Inline place of one of the endshield bolts.

Multi-Speed motors form numbers are as below for both Hori- GROUNDING
zontal and vertical motors
901 – 999 1) Conduit box ground
9001 – 9999 X$D Ultra® and severe duty are provided with bronze grounding
90001 – 99999 stud inside conduit box. On Open motors Bronze ground stud is
b. Nameplate Voltage. The last digit in this series designates provided on request however customer can use one of the
input voltage for stock horizontal motors only. conduit box fixing bolts for grounding.
4 = 575 volts
5 = 230/460 volts 2) End shield Ground Bolt Kit
6 = 200 volts End shield ground bolt kits are available for 140 thru 500 frame
8 = 460 volts product except 449HO. These kits are not allowed for use on
Division I motors.
7. First suffix letter
Denotes interchangeable design change of the complete
3) Servit Post
motor. If the first suffix letter is present it will be A, B, C, D, D1,
Servit post is mounted on frame close to the base of the motor.
D2….or D99.
This option is not allowed on Division I motors. The frame
8. Second suffix letter ground wire is passed through a hole in the servit post by the
Denotes special item or thermal device end user.

4) Ground Pad
NEMA type ground pads on frame can be provided on request.
These ground pads consist of bronze bolt and copper washer
mounted on a spot face area located on conduit box side near
foot.
Table 40
Frames Max Full load amps Bolt size Qty
143-286 160 5/16”-18 UNC 1
143-286 250 3/8”-16 UNC 1
449 HO 1200 0.500-13 UNC 2
324-5013 600 0.500-13 UNC 1
324-5013 1200 0.500-13 UNC 2

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
LEADS, SPECIAL Surge capacitors & Lightning Arrestors are used to protect the
All motors are provided with standard leads of ample length for motor from voltage spikes on the power line. Surge capacitors are
easy connection in the conduit box to the power leads. Lead size available without surge arrestors. Surge arrestors are available only
and material are dependent upon the class of insulation system in with surge capacitors.
the motor and the current capacity required. Longer than standard
leads, are available on request. TEMPERATURE RISE, SPECIAL
NEMA has defined allowable winding temperature rise according to
SPACE HEATERS class of insulation and maximum ambient temperature. Where
Space heaters are used to prevent moisture condensation in the there are requirements for special low winding temperature rise,
motor when it is not running. They are generally mounted on the please contact the Company for review of the available options.
opposite connect end of the stator on the OD of the end turns.
GE space heater kits are designed to raise the temperature of the TERMINALS, SPECIAL
winding 6.5 to 9 degree C above the ambient with an initial rate of All motors, except as mentioned below are supplied with Ring termi-
rise of 3.5 degree C per hour. They are suitable for use on both sin- nal (illustrated in Figure 30:
gle phase AC and DC voltage supplies. Surface temperature during • Non-X$D Motors in Frames 140-280, will be supplied with lead
operation is approximately 200 deg C. wire stripped for connection to power leads. 10.35

Special Div II Space Heaters: GE Motors has developed and

Selection & Application Guide

patented a thermostatically controlled space heater. These heaters
are provided with a hermetically sealed thermostat so they only
operate with a maximum surface temperature of 140 degree C and
do not spark in an end of life event. In order to limit surface temper-
ature rise during operation, these heaters operate at watt densities
significantly lower than standard heaters. The thermostat limits the
maximum temperature resulting from motor residual temperature Figure 30: Ring Terminal
(occurring as a result of motor operation), ambient temperature, THERMAL PROTECTION - WINDING
and space heater temperature. During continued normal operation The following devices are applicable only to motors with class B or F
with a 40 degree C ambient, the surface temperature will remain insulation.
below the thermostat setting; which will increase the life of the
heater. The thermostat opening temperature might be exceeded Built-in protective devices to prevent motor overheating may be ei-
due to high ambient and/or motor residual temperatures. ther: (A) Line interrupting devices which open the power supply
when the motor overheats or (B) pilot devices. The latter open the
In most cases when a motor is shut down, the space heaters are holding coil circuits of a magnetic switch to take the motor off of
immediately turned on. As the motor may take many hours to cool the line, or energize alarm bells or warning lights. Motors taken off
down, the heaters being automatically turned on can result in a cu- line by pilot devices typically cannot be restarted until an operator
mulative heat that may result in temperatures that approach the recloses the magnetic starting switch.
80% Auto-Ignition Temperature or AIT limit. A thermostatically con-
trolled heater will not allow the heater to energize until the motor A. Line-Interrupting Devices – Current-Sensing Thermal Protec-
has sufficiently cooled down (below 140C thermostat reset temper- tors
ature) thereby not allowing the temperatures to exceed the stated These protectors sense both motor temperature and current
AIT. and offer inherent protection against all abnormal stalled and
running conditions. They are built into the motor conduit box
STARTING CURRENT, LOWER THAN STANDARD for auto¬matic* reset operation on three-phase dripproof mo-
The starting current code (KVA-per-horsepower) for polyphase 60 tors 182-184 frames and for both automatic* and manual
Hz motors in the integral-hp sizes is code G. Reducing the amount reset operation on single-phase motors 182-215 frame.
of starting current to code F limits or lower may require more mate- These protectors are not available on explosion-proof motors
rial, increased frame size or a combination of these factors. Starting or on two-winding multispeed motors.
torque and breakdown torque may also be reduced to less than
NEMA design B limits. *WARNING: A MOTOR WITH AUTOMATIC-RESET THERMAL PRO¬TEC-
TION SHOULD NEVER BE USED WHERE AN UNEXPECTED RESTART
MAY INJURE PERSONNEL OR DAMAGE PROPERTY.
SURGE PROTECTION
Surge Capacitors & Surge Arrestors (Lightning arrestors)
Surge protection capacitors and lightning arrestors can be supplied
on 500 frame motors as a package in an oversize conduit box for
mounting adjacent to the motor.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
B. Pilot Devices MECHANICAL MODIFICATIONS
(1) Thermostats
These protectors are not available on explosion-proof motors BEARING – TEMPERATURE DETECTORS
or on two-winding multispeed motors. BTD’s are used to measure the temperature of bearings; these are
precision, wire-wound resistors with a known temperature resist-
Thermostats are mounted on the stator winding and are tem- ance characteristic. In operation, the BTD is usually wired into a
perature-sensing only. They are available with normally open specific type of circuit (Wheatstone bridge). The output of this circuit
or normally closed contacts and only for automatic reset. can be used to drive a meter, which has been calibrated, in temper-
ature, or to operate a relay to sound an alarm or shut down the
Thermostats will protect the motor from high ambient temperature, ex- motor.
ceedingly long accelerating cycles (where the design is not rotor lim-
ited), repeated or excessive overloads and loss of ventilation. However, BTD’s are constructed using a fine, pure, metallic, spring-like wire
they do not give protection under stalled or locked-rotor conditions and surrounded by an insulator and enclosed in a metal sheath.
must be used with an external current-sensitive motor control for com- • 120 Ohm Nickel
plete motor protection. • 100 Ohm Platinum
10.36 • 10 Ohm Copper
Thermostats can be installed in all motor enclosures. They are
BEARING THERMOCOUPLE
Selection & Application Guide

not recommended for machines with nameplate voltages ex-

ceeding 600 volts. A thermocouple is constructed of two dissimilar wires joined at one
end and encased in a metal sheath that an electromotive force
Thermostats are suitable for the following pilot circuits: (EMF) is developed by the thermoelectric effects. Any given set of
thermocouple wires have a known "EMF vs. Temperature character-
Table 41
istic. The other end of each wire is connected to a meter or measur-
Power Supply Voltage Current
ing circuit. Heating the measuring junction of the thermocouple
AC 110-115 volts 6.0 amp produces a voltage that is greater than the voltage across the refer-
AC 220-230 volts 3.0 amp ence junction. The difference between the two voltages is propor-
AC 440-480 volts 1.5 amp tional to the difference in temperature and can be measured on a
AC 550 volts 1.2 amp voltmeter.
DC 115-125 volts 2.2 amp
DC 230-250 volts 1.1 amp Thermocouples are classified based on the materials used for joints,
DC 550 volts 0.4 amp example are
Iron Constantan - Type J
(2) Thermistors Chromel Constantan - Type E
Thermistors are small non-linear resistance devices placed in Copper Constantan - Type T
the stator windings. As the critical temperature is reached, the Chromel Alumel - Type K
resistance of the thermistors changes radically, causing oper-
ation of a control relay. Normally, 3 thermistors are furnished, BRAKES
one per phase. Thermistors may be furnished with or without a Brakes supplied mounted on motors will be disc-type, spring set
separate (greater than 600 nameplate volts) control relay. electrically released brakes manufactured by Stearns Electric Corp.
(3) Resistance Temperature Detectors at General Electric Company option. Brakes are available for motors
RTDs are precision wire-wound resistors with calibrated tem- in frames 143-445only.
perature-resistance characteristics. These devices are used in
conjunction with customer supplied instruments and are avail- Several factors must be considered when determining the correct
able in 10, 100 and 120 ohm designs. Normally six RTDs (2 per brake for a particular application.
phase) are furnished per motor, suitably distributed around the
circumference of the stator winding, located between coil sides Refer to General Electric, for ‘frames above 445’ and ‘Special brakes
and positioned to detect the highest slot temperature. like Drum-Shoe / Floor-mounted’.
RTD’s are constructed using a fine, pure, metallic, spring-like
wire surrounded by an insulator and enclosed in a metal
sheath.
• 120 Ohm Nickel
• 100 Ohm Platinum
• 10 Ohm Copper

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
1. Brake Torque CONDUIT BOX, SPECIAL
Standard conduit boxes met or exceed NEMA and NEC volumes and
As a general rule of thumb, the torque rating of a brake should, are adequate for connecting all necessary leads for power and any
as a minimum, match the full-load torque of the motor on incidental control circuits.
which it is mounted. This will provide ample torque if the brake
is used for holding and will also provide a stop in approxi- Available options for motors in frames 182 through 449 include
mately the same time as required for acceleration. Full-load extra 3/4 inch conduit hole for dripproof, TENV and TEFC motors,
torque can be calculated as follows: additional conduit box, waterproof conduit box and oversize box.
5252 x Hp Motors in frames 509-5013 are available with a 2500 cubic inch
Full-Load Torque=
Full-load Speed motor mounted box suitable for stress cone connections or for
mounting accessory equipment. This special box is furnished as
For applications involving high inertia load, fast stops or a stop
standard for all motors of 3000 volts and above. Three stand-off in-
within a given time limit, the brake should be selected on the
sulator-supported copper bar terminations for motor leads can be
basis of total inertia to be retarded. Brake rating may be calcu-
furnished if specified. An 11,000 and a 17,000 cubic inch motor
lated as follows:
mounted conduit box are available. In addition, a 44,000 cubic inch
10.37
WK2 x RPM floor mounted, conduit box is available to mount beside the motor
Torque= with conduit connection to the motor frame. This construction al-
308 x t

Selection & Application Guide

lows the customer to mount accessories such as current transform-
Where: ers, surge capacitors, lightning arrestors, etc.
WK2 = Load inertia in lb-ft2
COUPLINGS
RPM = Full-Load Speed in RPM
Motors are normally furnished without couplings; however, a one-
t = Time, in seconds, to stop
piece half coupling can be installed on the motor shaft at the fac-
tory providing it is balanced, finished machined and key-seated to
Standard brake torque ratings or continuous duty include: 6, 10, 15,
motor shaft dimensions. It must be shipped prepaid to the factory
25, 35, 50, 75, 105, 125, 175, 230, 330, 440, 550 lb-ft. If the calcu-
of motor manufacture before the start of production. Motors are
lated brake torque falls between the standard torque values, spec-
dynamically balanced prior to installing the half coupling and are
ify the next higher torque.
not rebalanced after coupling assembly.
2. Brake Voltage
Brakes are supplied for operation on the same voltage as the A vibration test with half-coupling installed will be performed and a
motor unless otherwise specified. In the case of dual voltage test report issued when this special service is requested by the cus-
motors, brake voltage will be the lower of the motor voltages, tomer and included in the quotation.
unless otherwise specified. Standard brake voltages are:
DOWEL HOLES IN FEET
60 hertz 200, 230, 460, 575 Volts
Dowel holes are furnished as standard on 500 frame motors as an
50 hertz 200, 220, 380, 415, 440, 550 Volts
alignment aid. One 1/2 inch hole is provided in each of the diago-
Stearns brakes are all single-phase. Dings brakes are single- nally opposite feet.
phase up to 9 lb-ft and three-phase in larger ratings.
ENDSHIELDS, SPECIAL
Brake leads are terminated at a conduit connection on the Horizontal motors are available with Type C face, and D flange end-
brake. shields, which have rabbets and bolt holes for mounting equipment
3. Brake Enclosure to the motor, or for overhanging the motor on a driven machine.
The Type C face endshield provides a male rabbet and tapped holes
Brakes are available in enclosures to match the needs of the for mounting bolts. This endshield is used for mounting small appa-
environment in which they will be operating. Standard enclo- ratus, such as pumps, to the motor. The Type D flange has a male
sure is for application on dripproof or totally-enclosed fan- rabbet, with holes in the flange for through bolts. This flange is pri-
cooled motors for indoor or semi-protected outdoor marily used on machine-tool gear boxes.
installations. Dust-tight, waterproof enclosure is suitable for
severe-duty and totally-enclosed motors used in conditions of
extreme moisture, abrasive or conductive dusts, acid or alkali
fumes or for outdoor installation.
4. Vertical Mounting Position
Brakes must be specially modified for vertical mounting. Spec-
ify if the motor will be above or below the brake.

Figure 31: Type C-Face

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
Table 42: C-Face Mounting Dimensions (inches) FRAME, NON-STANDARD
Dimensions in inches Requests are occasionally received to furnish motors in frame sizes
either larger or smaller than NEMA standard. If frame size larger
Face Rabbet
Bolt Circle Bolt Holes than standard is to be supplied the standard motor rating for that
NEMA Diameter Diameter
frame size will be furnished. If smaller than standard frame is re-
Frame BD AK AJ BF quired, please contact the Company for feasibility and terms.
Size
Tap Size Min. Depth
GREASE & RELIEF FITTINGS
182-184 8.50 8.50 7.25 .50-13 .75 Motors with regreasable bearing systems can be supplied with re-
213-215 8.68 8.50 7.25 .50-13 .88 grease fittings and automatic grease relief devices. Severe-duty
254-256 8.68 8.50 7.25 .50-13 .88 motors are supplied with extended hydraulic grease fittings and
plugs.
284-286 10.75 10.50 9.0 .50-13 .88
324-326 12.75 12.50 11.00 .625-11 1.06 SHAFTS, SPECIAL
364-365 13.00 12.50 11.00 .625-11 1.06 Motors are furnished with a single straight shaft with sled runner
10.38 keyway and a rectangular key. For motors in frames 182 through
404-405 1300 12.50 11.00 .625-11 1.06
449, a long shaft for V-belt drive is supplied for a majority of ratings
444-449 13.00 12.50 14.00 .625-11 1.06 and is denoted by the suffix “T” or “L” on the motor frame size. Two-
Selection & Application Guide

pole (3600 RPM) motors in frames 284 through 449 and certain
Note: Frame 182 through 326 have 4 holes; 364 and larger have 8 other 449 frame ratings are furnished with short shafts for direct
holes connection. These motors are denoted with the suffix “TS”, “LL” or
“LS” on the motor frame size. Standard double-end shaft extensions
are available for motors in frames 182 through 5011.
Special shaft designs are available including differences in dimen-
sions and/or materials as follows:
Length: Up to 10 inches longer than standard for motors in
frames 182-449.

Up to 13 inches longer than standard for motors in

frames 509-5013.

Longer than standard shafts are usually suitable for di-

Figure 32: Type D-Flange rect connection. Other drives such as belts or gearing
may require special bearings and should be referred to
Table 43: D-Flange Mounting Dimensions (inches) Company.
Keyway: Sled-runner, round end, or Woodruff #3 or #9
Dimensions in inches
Hole: Drilled radially or in the end of the shaft. Drilled and
NEMA Face Rabbet
Bolt Circle Bolt Holes tapped in the end of the shaft. Hole depth limited to
Frame Diameter Diameter
three times the hole diameter 26.
Size BD AK AJ BF
Steps: One or more reductions in shaft diameter.
182-184 11.00 9.00 10.00 .53
Threads: Class 2A right-hand thread of size appropriate to the
213-215 11.00 9.00 10.00 .53
shaft diameter.
254-256 14.00 11.00 12.50 .81
Squared: Milled flats on four sides of one step.
284-286 14.00 11.00 12.50 .81
Tapered: 1 1/4 or 1 1/2 inch per foot taper with threads, nut and
324-326 18.00 14.00 16.00 .81
lock washer.
364-365 18.00 14.00 16.00 .81
404-405 21.90 18.00 20.00 .81
444-449 21.94 18.00 20.00 .81

Note: Frames 182 through 365 have 4 holes. 404 and larger have 8
holes.

C-face and D-flange kits are available for field modification of stan-
dard motors by an Authorized GE Service center. These kits are pro-
vided as a convenience item. Conventional motors will not meet
NEMA BA dimensions and there is some loss in usable shaft length.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
SHAFT SLINGER ENVIRONMENTAL MODIFICATIONS
A Steel reinforced neoprene shaft slinger shaft slinger is an elas-
Care is needed in using motors that have a combination of unusual
tomer ring disc mounted on the shaft .it reduced the probability of
environmental conditions. For example, a motor with a requirement
the contamination of the bearing system when the shaft is rotating.
of high altitude plus high temperature and service factor may be
(Not available on explosion proof). Shaft slinger is standard on drive
available only in an oversized frame.
end for all SD motors and on both ends on X$D Ultra® motors (ex-
cept C-face and D-flange., for 140-280 frames).
ALTITUDE
The rating of standard motors assumes operation at sea level in a
TACHOMETER
40°C ambient. For purposes of standardization it is considered that
Tachometer and encoder are terms used for equipment that has an
there is no difference in motor operating temperature between sea
output signal indicating the motors speed. The degree of sophistica-
level and 3300 feet altitude.
tion is diverse - ranging from a DC voltage proportional to speed to
dual output frequency pulses up to a few thousand pulses per revo-
The cooling effect of ventilating air is a function of its density. The
lution (PPR) which can be used to indicate not only velocity, but also
atmospheric pressure and density at higher altitudes is reduced
acceleration and position when used in association with equipment
and the air cannot remove as much motor heat, causing the motor
to interpret the signals.
to run hotter. As a general guide, motor temperature rise increases 10.39
1% for every 330 feet above 3300 feet. To keep motor heating
TACHOMETER OR ENCODER MOUNTING PROVISION within safe limits at altitudes above 3300 feet, there are the follow-

Selection & Application Guide

For mounting C-face tachometer, motor is supplied with an 8.5” C- ing alternatives:
Face mounting on the opposite drive end with a stub shaft. Cus-
tomer to provide; the ‘stub shaft dimensions’, ‘manufacture’ & ‘style’ A. Supply a motor designed for standard sea level operation which
of device to be mounted, with order. can either be:
(1) Operated at less load (a motor with service factor rating of
For mounting tether tachometer motor supplied with opposite drive 1.15 or higher can be operated at altitudes up to 9000 feet with
end shaft extension and a hole drilled and tapped in the fan cover / a 1.0 service factor), or
endshield to secure the anti-rotation device. Customer to provide; (2) Operated in a lower ambient temperature per the following
‘detailed shaft dimensions’, ‘manufacturer’ and ‘type’ of the table 44:
tachometer device.
Table 44
VERTICAL JACK SCREWS If Ambient Maximum Altitude with Same
Vertical jackscrews are used during alignment of the motor and Temperature is: Service Factor is:
drive equipment. The jackscrew is used as an aid to insert the
30 ºC 6600 ft
proper shims. Vertical jackscrews are NOT intended as permanent
20 ºC 9900 ft
support of the motor. Proper shimming and bolting of the motor to
the base must be completed and tension removed from the It should be remembered that, although the outdoor ambient
jackscrews temperature at higher altitudes is low, motors probably will be
installed indoors in higher ambient temperatures.
VIBRATION DETECTION
Motors can be provided with Vibration switch or Vibration detection Motors applied per A(1) or A(2) above, will have no special
probes / Transmitters or with only provisions for vibration probes altitude or temperature data on the nameplate.

B. Supply a special motor designed for the required high altitude

VIBRATION SWITCH
operation, with appropriate data stamped on the nameplate.
Provided with ‘SPDT (or) DPDT Switch’ which disconnects the
motor power circuit; when the motor vibration level exceeds the
set vibration limit.
HIGH AMBIENT, POLYPHASE
Standard motors are designed so that the temperature rise pro-
duced within the motor, added to the standard 40°C ambient tem-
VIBRATION PROBES/TRANSMITTERS
perature, will not exceed the winding-insulation temperature limit. If
This transmits electrical signal (mA) proportional to velocity or
the ambient temperature exceeds 40°C:
displacement, directly to PLC or DCS or any other vibration
monitor.
A. The temperature rise produced in the motor must be offset by:
These are generally mounted on the endshields, above the bear-
(1) Reducing the load and consequent motor losses. A motor
ings. When it is not feasible to mount on the endshields, they can be
rated for a 40°C ambient temperature and operating in a 50°C
mounted on the frame, close to the endshields.
ambient, will, if rated 1.15 service factor, carry rated Hp with no
overload (1.0 SF) and, if rated 1.0 service factor, carry 90% of
rated Hp, or by…

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
(2) Applying a special motor design. PAINT

B. The temperature limit may be raised by the substitution of a Standard Finishes

higher-temperature insulation system, special grease and Motors are protected by a two coat paint system. The first coat is a
bearings. rust-inhibitive primer applied to protect the castings during storage
and manufacture. The second coat is a medium light gray or buff
Motors applied per A(1) above will not have special ambient temper- semi-gloss paint. Most commercially available paints are compati-
ature or service factor data on the nameplate. ble with the paint system described above. It is recommended that
the customer apply any finish coat over the motor paint in his plant
The choice between A(2) and B rests with the motor designer who when the driven equipment is painted.
also may have to use a frame size larger than is standard for the
rating. Explosion-proof motors may require frame sizes different Special Finishes
from the corresponding totally-enclosed motors.
Special paint like high solids polyurethane epoxy paint system (Cor-
rosion resistant epoxy) is used for salty atmosphere.
WARNING: THE MAXIMUM ALLOWABLE AMBIENT TEMPERATURE FOR
EXPLOSION-PROOF MACHINES IS 60°C.
10.40 It’s a 3 part paint process
1. Primer coat - Penetrating sealer
HIGH AMBIENT, SINGLE-PHASE 2. Intermediate coat – 2-part epoxy
Selection & Application Guide

For operation in ambient temperatures higher than 40°C, refer to 3. Finish coat Polyurethane topcoat with color
Company giving full details of the application.
Outside surface of TEFC ODE endshields and inside of fan cover are
LOW AMBIENT also coated, with at least one finish coat.
For operation in ambient temperatures of less than minus 40°C,
give full details of the application. Special low-temperature grease Dry film thickness (DFT) adds up to 10 mils.
and special steel shafts may be required.
SCREENS
DRIP COVERS (WALL OR VERTICAL MOUNTING)
Drip covers can be furnished on standard horizontal motors for Intake and Discharge Screens – Dripproof Guarded
added protection from dripping liquids and falling objects when the
Corrosion resistant screens can be furnished over the air- intake
motor is mounted in other than the normal horizontal position.
and discharge openings of dripproof motors. Dripproof motors
equipped with these screens conform to the “Dripproof Guarded”
If dripping liquids are present in the application, protective covers
definition appearing in NEMA MG-1, Part 1.
are recommended for dripproof construction motors mounted shaft
up or shaft down.
Rodent Screens – Rodent screens will be provided where required
as part of the dripproof guarded system and on specific request of
If motor is not nameplated for “W1-W8”, need to rotate the end-
the purchaser.
shield, to suitably locate the drain and plug.

EXPORT BOXING AND PACKING SHAFT SEALS ( LIP SEAL / NON-CONTACT LABYRINTH SEAL)
Export boxing and packing should be specified when a motor, and/
Non contact Labyrinth seals are metallic seals with rubber sealing
or spare parts, are to be furnished for export shipment.
rings, which provide protection against both dust and liquids.
GREASE, SPECIAL
Lip seal (contact type) consists of a spring loaded rubber circular
Motors designed for unusual environmental conditions or special
lip. The spring loaded lip prevents entry of dust and liquid objects in-
duty should have bearing grease selected for such service. The
side the motor.
most commonly encountered conditions requiring special lubri-
cants are extremely high or low operating ambients. The majority of
Either of the above seals is provided on request.
motor greases used by GE are suitable for operation at ambient
temperatures from minus 40 °C to plus 40 °C.

GE uses special grease for very low ambient of minus 54 C.

HARDWARE
Standard motor hardware has a plated protective coating suitable
for the corrosive atmospheres generally encountered. For ex-
tremely corrosive atmospheres, stainless steel hardware may be re-
quired, and should be specified.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
The following tabulation (Table 45) lists the sealing arrangement X$D Ultra® NEMA Premium® EXTRA SEVERE-DUTY MOTORS
where shafts emerge from the motor bearing housings.
Table 45: Shaft Seals Description:
The X$D Ultra® line of NEMA Premium® efficiency motors is de-
GE Motor Enclosure Motor Frame signed especially to operate in the rugged environments found in
182 509 the process industries such as chemical, petroleum, plastic, paper,
449 5011 metals and cement. These Extra Severe-Duty motors are well suited
Shaft Seal for a wide variety of applications including pumps, compressors,
fans, blowers, materials handling equipment and drives for special
Standard Dripproof F F process machinery – wherever premium efficiency, reliability and
Totally Enclosed F F long life are basic requirements of the application.
Severe-duty Enclosed S S
X$D Ultra ® S S Product Line:
Explosion-proof F* F* NEMA Design A and C
IEEE-841 L L (GE Types KS and KGS)
API-661 L Not Applicable Enclosure TEFC Extra Severe-Duty
10.41
Frames 143-449
F = Close running fit at both ends. Voltage 230, 460 or 575 Volts

Selection & Application Guide

S = Neoprene slinger steel reinforced DE only. Frequency and Phase 60 hertz, 3-phase
L= Non-contact Labyrinth seals. Ambient 40°C, 1.15 Service Factor
* Except Class II Group E motors which have non-sparking labyrinth 65°C, 1.0 Service Factor
seals. Ratings Available 1.5-250 Hp, 3600 RPM
1-250 Hp, 1800 RPM
0.75-200 Hp, 1200 RPM
SPECIAL AND DEFINITE PURPOSE APPLICATIONS 0.5-150 Hp, 900 RPM

CLOSE-COUPLED PUMP MOTORS BEARING LIFE

A Quick explanation of L10 & L10a Bearing life calculations:
Description:
These motors are designed to meet the requirements of motor L10 life is the basic rating life expressed in millions of revolutions or
mounted centrifugal pumps. number of operating hours at 90 % reliability.
The bearing life, in hours for 90% reliability, for anti-friction bearings
Product Line: expressed as:
NEMA Design B (GE Types K and KS)
Enclosure Dripproof or Totally-Enclosed Fan L10 = 1000000 * (C/P)n
Cooled 60*rpm
Frames 182-365 Where:
Voltage 200, 230, 460, 575 rpm = rotation speed
Frequency and Phase 60 hertz, 3-phase or single-phase C = bearing dynamic capacity
Ambient 40°C Dripproof, 1.15 Service Factor P = equivalent radial load
40°C TEFC, 1.15 Service Factor n = 3 for ball bearing and 10/3 for roller bearing
Ratings 1 through 60 Horsepower
L10a life is the rating life expressed in millions of revolutions or
Standard Features: number of operating hours considering life adjustment factors for
Motors feature a NEMA Type C-face endshield and a standardized reliability, material and operating conditions.
shaft extension on which the pump casing and impeller are
mounted. Machining is to close axial and radial tolerances. Motor L10a life = a1*a2*a3*L10
dimensions for this compact assembly are per the NEMA “JM” and Where a1= adjustment factor for reliability
“JP” standards established in conjunction with the pump industry. a2= adjustment factor for bearing materials
Standardization permits a high degree of interchangeability of a3= adjustment factor for bearing operating conditions in-
pump and motor sizes; special pump parts are held to a minimum. cluding adequacy of lubrication, cleanliness, temperature etc.
Generally a2 and a3 factors are combined and called as a23 -
Combined Life Adjustment Factor.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
X$D Ultra® Features: MULTI-SPEED MOTORS
As a result of careful reviewing of the special needs of the process
industries, motors in this product line include many unique features.
Description:
X$D™ motors have a bearing life (L10) of 130,000 hours for direct
Multispeed motors are applied where operation at two, three or four
connected loads and 26,280 hours for belted applications.
definite speeds is desired. The motors are classified as to the rela-
tion of full-load torques at rated speeds: i.e., constant torque, vari-
Lower motor temperature provides a cooler operating bearing sys-
able torque and constant horsepower.
tem which significantly increases grease life. The combination of
the better bearings and long life grease improves motor reliability
Product Line:
and reduces maintenance costs. Motors are equipped with re-
NEMA Design NEMA design does not apply for multi
greasable antifriction bearings with readily accessible inlet hy-
speed motors(GE Types K, KS)
draulic grease fittings and Allen head outlet plugs for convenient
Enclosure Dripproof or Totally-Enclosed,
relubrication.
Explosion-Proof Fan-Cooled
Frame 182-5011
Motors are dual-rated with a service factor of 1.15 in a 40°C ambi-
Voltage 200, 230, 460, 575
ent or 1.0 in a 65°C ambient. NEMA Premium® efficiency provides
10.42 Frequency and Phase 60 hertz, 3-phase
extra thermal margin, often allowing these motors to be used on
Ambient 40°C, Dripproof, 1.15 Service Factor;
adjustable speed drives without derating. The extra margin also
40°C, TEFC, 1.0 Service Factor
Selection & Application Guide

provides protection against momentary conditions of overloads,

Rating 1 through 800 horsepower
voltage fluctuations, single-phasing and stall. Thermal margin can
• One winding, two winding Variable
be utilized to meet the needs of duty cycle loads. X$D Ultra® mo-
torque, constant torque and
tors are available with NEMA design B (normal) or NEMA design C
constant horsepower
(high) starting torque.
2 speed, 3 speed, 4 speed
Cast iron frame and endshield construction is used for these totally-
Application:
enclosed fan-cooled motors. All external parts are protected by
Different speeds are obtained by switching electrical connections.
epoxy paint or equivalent. The stainless steel motor nameplate pro-
The speed on each connection has the constant speed characteris-
vides complete motor data including efficiency values and bearing
tic typical of single-speed induction motors. Multispeed motors may
numbers.
have a single re-connectible winding or two independent windings.
The conduit box is fully gasketed with a lead separator gasket, be-
It is possible to arrange a single winding so that it can be recon-
tween the box and motor frame and another between the cover
nected for a different number of poles (and speed) by suitable re-
and box. Further protection of internal parts is provided by an ex-
connection of the leads. However, such an arrangement will permit
ternal slinger on the motor shaft which helps prevent moisture from
only two speeds and the speeds must be in the ratio of two-to-one.
seeping along the shaft into the motor.
An alternate way of securing two speeds is to have two separate
Motors are built with a full class H insulation system (with class “F”
windings, each wound for a different number of poles and speed.
leads) using non-hygroscopic materials throughout to resist mois-
ture and help extend thermal endurance. Air gap surfaces are pro-
Such an arrangement means that one winding is not in use when
tected against corrosion.
the other is connected to the line; motor frame sizes usually are
larger in order to accommodate the idle winding. But the use of two
Safety features include a grounding stud in the conduit box plus
windings permits two speeds which are not in the ratio of two-to-
built-in 4 point cast-in lifting lugs for easy installation and mainte-
one. Speeds with a two-to-one ratio can be delivered by two-wind-
nance. All X$D Ultra® motors have CSA approval.
ing motors as well as by single-winding motors.

The choice between one winding and two winding motors is af-
fected by the speeds desired, the motor price, the control price,
wiring complexity and physical size. One winding motors have
lower prices than two winding motors but usually require more ex-
pensive controls.

A four-speed motor has two windings and each winding is arranged

for two speeds having a two-to-one ratio. If one of the two windings
is single speed, the motor has a total of three speeds. A motor with
three windings, which would permit speed combinations like 1800/
1200/720 RPM, is not a practical design.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Multispeed motors are classified by the relation of the full-load and stopping. Since the full-load current for high speed is different
torques at the two (or more) full-load speeds. from that for the lower speeds, separate independent thermal over-
load relays with correctly selected heaters are required in the con-
If the motor has the same full-load torque at both speeds, the trol to completely protect the motor on all speed connections.
motor is a constant torque motor. Since constant torque motors
have the same full-load torque at both speeds, the horsepower rat- An alternate is to specify multispeed motors equipped with heat-
ings for the two speeds are in the same ratio as the speeds. For ex- sensing protectors, built into the winding to positively prevent
ample, the low speed rating of a 10 Hp 1800/900 RPM constant burnouts caused by overloads, stalling, lack of ventilation, single-
torque motor is 5 Hp. phasing or unbalanced voltages regardless of speed, winding con-
nection or ambient temperature.
If the full-load torques are in the same ratio as the speeds, the
motor is a variable torque motor. The horsepower at the low speed, Multispeed motors are supplied for a single voltage. Motors larger
involving both reduced torques and speed, compares to the high than 365T frame are not furnished for voltages below 460 volts at
speed in ratio of the square of the speeds. Therefore, in the case of 60 hertz (380 volts at 50 hertz).
a 10 Hp 1800/900 RPM variable torque motor, the low speed horse-
power is 2 1/2 using the following equation: Multispeed motors may be started on any speed either on full volt-
10.43
age, or on reduced voltage by resistor, reactor or autotransformer

[ ]
RPM LOW 2
starters. They are not available for wye-delta or part winding starting.
Hp LOW = Hp Hi

Selection & Application Guide

RPM HI
OIL WELL PUMPING MOTORS
If the full-load torque value at the two speeds varies inversely to the
speed, the motor is designated constant horsepower. Description:
Type KOF or KOW motors have special performance characteristics
The horsepower listing of multispeed motors always applies to the particularly suited to the requirements of beam drives for oil well
highest speed. The horsepower ratings at the lower speeds are de- pumping.
termined by the particular speed and the motor’s torque classifica-
tion. Motor horsepower is a direct function of both torque and Product Line:
speed. NEMA Design D (GE Type KOF-Single Horsepower or
KOW-Triple Horsepower)
For each speed of a multispeed motor, the horsepower rating must Enclosure Dripproof Guarded or Totally-Enclosed
be equal to, or greater than, the horsepower required by the driven Fan-Cooled
load at each speed. Frame 213T through 449T
Voltage 460/796 at 1200 RPM; 230/460 at
Constant-torque motors are used on friction type loads, or where 900 RPM
the work being done is in direct proportion to the speed. Typical ex- Frequency and Phase 60 hz, 3-phase
amples of constant torque loads are conveyors, escalators and Ambient 40°C 1.0 Service Factor
positive displacement pumps or compressors. Rating 3 through 125 Hp

Variable torque motors are normally applied to fans centrifugal Standard Features:
blowers and centrifugal pumps which put a horsepower load on the The construction of the dripproof motors is mechanically strong
motor which varies as the cube of the speed. If the motor output is and resists corrosion. Rodent screens are standard on all ventilating
adequate for the high speed load, it is sure to have enough Hp at openings. The motors have a varnish system ideal for rugged out-
the lower speeds since the motor Hp reduces only as the square of door service in the oil fields for the optimum in mechanical protec-
the speed. tion. There is a Totally-Enclosed Fan-Cooled motor in all cast iron
IP55 enclosures with a 1.15 service factor.
Constant horsepower motors are applied on machines that must
handle a heavier weight or a greater cut (machine tools) on lower Electrically, the oil well pumping motor has high slip and high
speed than on high speed. For example, a metal-cutting lathe torque to assure lower kw-hr per barrel. Type KOF motors are de-
would use the high-speed connection for a light finish cut, but the signed to deliver ideal torque and slip characteristics at the high
low-speed connection for taking off large chips in a rough cut. voltage (460/ 796 volts) normally available from oil field distribution
systems.
Multispeed ratings may have lower starting torques than the corre-
sponding single speed ratings.

Multispeed motors are connected in various ways requiring special

control, whether manual or magnetic, for starting, changing speeds

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
TOTALLY-ENCLOSED AIR-OVER (TEAO)

Description: Product Line:

Totally-Enclosed Air-Over (TEAO) motors are specifically designed NEMA Design B (GE Types K, KS)
for fan and blower applications where the air being moved passes Enclosure Totally-Enclosed Air-Over
directly over the motor frame to cool the motor. Motor ratings can Frames 182-405
be selected based upon velocity of cooling air over the motor Voltage 200, 230, 460 or 575 Standard
frame. It is often possible to select a smaller frame for a given load Frequency & Phase 60 hertz, 3-phase
resulting in cost and space savings. Motor thrust capability ratings Ambient 40°C maximum
assume a fan mounted on the motor shaft. The motors can be belt Ratings See Table 46
connected to the fan or blower as long as an adequate velocity of
air flows directly over the motor. The totally-enclosed construction
prevents moisture, dust and other contaminants from entering the
motor from the air stream.

10.44
Table 46: Totally-Enclosed Air-Over Motor Application Data
Minimum Air Max. Minimum Air Max.
Selection & Application Guide

Max. Fan Max. Fan

Syn. RPM Hp Velocity Thrust Syn. RPM Hp Velocity Thrust
Wt. Lbs. Wt. Lbs.
(Ft/Min) Pounds (Ft/Min) Pounds
900 1.0 100 3600 30.0 1500
450 165
1200 1.5 100 1800 30.0 1200
375 540
900 1.5 100 1200 30.0 800
560 860
1200 2.0 100 900 30.0 800
900 2.0 200 250 250 3600 40.0 1900 600 215
3600 3.0 200 1800 40.0 1500 430 800
1800 3.0 200 1200 40.0 1000 680 1070
1200 3.0 250 250 250 900 40.0 800 830 1070
900 3.0 200 250 250 3600 50.0 1900 600 215
1800 50.0 1500 430 800
3600 5.0 200
1200 50.0 1000 680 1070
1800 5.0 200
900 50.0 1000 950 1200
1200 5.0 250 250 250
3600 60.0 2250 530 315
900 5.0 400 460 535
1800 60.0 1700 480 1070
3600 7.5 800 145 165
1200 60.0 1200 800 1200
1800 7.5 600 200 250
900 60.0 1000 950 1200
1200 7.5 500 375 535
900 7.5 400 460 535 3600 75.0 2250
3600 10.0 800 145 165 1800 75.0 1700
1800 10.0 600 200 250 1200 75.0 1200
1200 10.0 500 375 535 900 75.0 1200
900 10.0 500 500 690 3600 100.0 2500
1800 100.0 1875
3600 15.0 1250 340 125
1200 100.0 1400
1800 15.0 950 340 420
900 100.0 1200
1200 15.0 600 400 690
900 15.0 500 500 690 3600 125.0 2700
1800 125.0 2025
3600 20.0 1250 340 125
1200 125.0 1400
1800 20.0 950 340 420
900 125.0 1200
1200 20.0 600 750 400
900 20.0 700 390 860 3600 150.0 2700
1800 150.0 2025
3600 25.0 1500 450 165
1200 150.0 1400
1800 25.0 1200 375 540
900 150.0 1200
1200 25.0 800 560 860
900 25.0 700 390 860 3600 200.0 2700
1800 200.0 2025
1200 200.0 1400
3600 250.0 2700
1800 250.0 2025

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Selection:
The horsepower required by the fan should be determined based
on handling “standard” air at 70°F temperature with a density of
0.075 pounds per cubic foot.

Minimum air velocity in feet per minute listed in Table 46 must flow
directly over the motor frame for continuous operation at rated
horsepower.

The air velocity along the motor is affected by fan design factors
such as:
1. Fan hub dimensions relative to motor frame diameter.
2. Fan hub diameter relative to fan blade diameter.
3. Position of the motor in the air stream.
4. Method of mounting motor (feet, face, flange, etc.).
5. Characteristics of air flow (turbulent, laminar, etc.).
10.45

In view of these factors and other potential variables, the fan manu-

Selection & Application Guide

facturer has the ultimate responsibility for proper motor selection
and applications.

Thrust values in Table 46 assume maximum fan weight and repre-

sent the maximum permissible thrust to provide a 14 year average
bearing life and a 25,000 hour L10 life in accordance with AFBMA
bearing life calculations.

Fan weight shown is the maximum weight of a fan in “commercial

balance”, concentrated at the end of the motor shaft extension,
which is permissible for safe shaft and bearing loading. A fan has
commercial balance if its unbalance moment in ounce-inches (the
weight in ounces times the distance in inches from the axis of rota-
tion required to produce perfect balance) is numerically equal to, or
less than, one percent of the weight in pounds of 1200 RPM and
higher speed fans or five percent of the weight in pounds of lower
speed fans.

Vertical mounting applications (shaft up or down) should be referred

to Company to determine whether drive-end bearing should be
clamped.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
ADJUSTABLE SPEED INVERTER DUTY OPERATION X$D Ultra® GEGARD2000 incorporates Class H rated GE701 varnish,
which consists of 100% solids and has no solvents that evaporate
during the curing cycle.
PRODUCT
NEMA Design does not apply (GE Type KAF) With the use of a more sophisticated design GE Fuji has solved the
Enclosure: Open Dripproof or Totally-Enclosed spiking issue and offers drive products that keep the spike under
Frames: 143-5013 1000 volts and are compatible with older existing motors.

ADJUSTABLE SPEED DRIVE (A$D™) OPERATION Besides the motor insulation system, the application should con-
Most of today’s state-of-the-art inverter drives use IGBT technol- sider the shortest leads possible between the drive and motor (50 ft)
ogy. These drives solve the electrical noise problem of the older and make sure the motor has enough thermal capability to support
transistor units but can create significant issues for pre-IGBT motor the application at reduced speeds.
insulation life. The IGBT drive use frequencies that are above the au-
dible range and can cause significant rapid voltage spikes that may The point here is that being IGBT “Compatible” is not necessarily “In-
shorten motor insulation life. verter Duty”. Standard efficiency motors with appropriate IGBT
compatible insulation have as a primary design parameter cost not
10.46 Motor manufacturers, through the National Electrical Manufactur- variable speed loading capability. Many simple applications can be
ers Association (NEMA) technical section have defined IGBT drive served with these standard motors but all the parameters must be
Selection & Application Guide

output spike voltage as 3.1 times the motor nameplate voltage. considered. Some of the most significant are:

Example: NEMA MG-1-31 states 3.1 times the nameplate voltage or • Thermal stress for low frequency constant torque loads.
460 volts X 3.1 = 1425 minimal acceptable voltage spike @ .01 mi- • Low frequency performance - speed oscillation
crosecond rise time. • Lead length
Similarly for 575V; the voltage spike = 575 volts X 3.1 = 1783 V • System information feedback

Specific to this application, GE uses insulation system to withstand If any of these items are necessary or unknown the user should
spike voltages up to 2000V. consider the true Inverter Duty Motor.

A$D™/LOAD REQUIREMENT DATA SHEET

VARIABLE FREQUENCY OPERATION:

Design Point Hp@ RPM

Range (Min-Max) - RPM
Type Load Variable Torque Constant Torque
Above Design RPM Constant Hp CTq VTq

A$D Type: PWM (Pulse Width Modulated)

VSI (6 Step Voltage Inverter)
CSI (6 Step Current Inverter)

Make Model #
Fill out only the applicable requirements below:
Service Factor (sine wave) (A$D)
Temp Rise (sine wave) (A$D)
Overload (150% for 1 minute standard):
Overload (%) of the motor required at top speed:
Starting Torque (140% rated torque with 150% Rated Current Standard):

Is NEMA A Design acceptable if required to keep in NEMA frame?

(Will have higher inrush. May be undesirable if inverter bypass is required.)

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
Table 47: Quick reference of Industrial Applications for 3 Phase Induction Motors

Requirements
Applications Locked- Environment Standards GE Types
NEMA De- Starting Breakdown
Rotor % Slip
sign Current Torque
Torque
Normal starting torque, con- K, KE, KS
stant load (single) speed, NEMA MG1
High to X$D Ultra®
such as A Normal Normal Max 5% Non Hazardous
Medium KS-X$D Ultra®
• Fans IEEE-841
• Blowers 841
• Pumps DIV 1 UL/CSA K, KE, KS - XP
• Machined tools
• Unloaded compressors DIV 2 UL/CSA K, KE, KS
• Some conveyors Hazardous
• Metal cutting machine tools Zone 1 UL/CSA K, KE, KS - XP
B Low Normal Normal Max 5%
• Misc. machinery UL/CSA, ATEX, CE
Zone 2 K, KE, KS
MARK
10.47
Marine IEEE45 KS-X$D Ultra®
Constant load (single) speed KG, KGS,

Selection & Application Guide

Non Hazardous NEMA MG1
X$D Ultra® KGS
High inertia starts such as
• Large centrifugal blowers DIV 1 UL/CSA KG, KGS - XP
• Flywheels DIV 2 UL/CSA KG, KGS
• Crusher drums C Low High Normal Max 5% Hazardous Zone 1 UL/CSA KG, KGS - XP
Loaded starts such as UL/CSA, ATEX, CE
• Piston pumps Zone 2 KG, KGS
MARK
• Compressors
• Conveyors Marine IEEE45 KGS-X$D Ultra®
Very high inertia and loaded Non Hazardous NEMA MG1 KR
starts. Choice of slip to match
load. 5-8%
DIV 1 UL/CSA KR XP
• Punch presses
• Shears
DIV 2 UL/CSA KR
• Forming machine tools D Low Very High –
Hazardous
• Cranes Zone 1 UL/CSA KR XP
• Hoists 8-13%
• Elevators UL/CSA, ATEX, CE
Zone 2 KR
• Oil well pumping jacks MARK

Constant torque applications,

such as NEMA MG1 KAF/X$D Ultra®
• Agitators Non Hazardous
• Centrifuges KS-X$D Ultra®
IEEE-841
• Conveyors 841
• Extruders
• Feeders Application Not Not Application DIV 1 UL/CSA KAF
• Grinders –
• Kilns Driven Applicable Applicable Driven
• Mills DIV 2 UL/CSA KAF
• Mixers Hazardous*
• Presses Zone 1 UL/CSA KAF
• Saws
• Test Stands UL/CSA, ATEX, CE
Zone 2 KAF
• Tools MARK
High to ##Non Hazardous NEMA MG1, KS-X$D Ultra®
Cooling Tower Fans A or B Normal Normal Max 5%
medium Suitable for Div 2 API 661 661
Reciprocating Compressors High to NEMA MG1,
A or B Normal Normal Max 5% – 500 Frame
(High Speed) medium API 541 & API 547

K, KE, KS, KAF, KG, KGS, KR – Refer Model Nomenclature in Page 34.

* Refer to GE, for specific suitability requirements such as AIT, Gas Groups & Rating Details.
## Product offering limitation. Refer to GE for more information.

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
ANNEXURE A
TABLE 48: QUICK COMPARISON BETWEEN NEMA & IEC MOUNTING DIMENSIONS

Dimensions in reference above sketch stand for NEMA (IEC)

Frame Size D (H) 2E (A) 2F (B) BA (C) H (K) N-W (E) ØU (ØD)
IEC NEMA IEC NEMA IEC NEMA IEC NEMA IEC NEMA IEC NEMA IEC NEMA
10.48 IEC NEMA mm mm mm mm mm mm mm
mm mm mm mm mm mm mm
(inch) (inch) (inch) (inch) (inch) (inch) (inch)
88.9 139.7 101.6 57.2 8.6 57.15 22.225
Selection & Application Guide

90S 143 90 140 100 56 10 50 24

(3.5) (5.5) (4) (2.25) (0.34) (2.25) (0.875)
88.9 139.7 127 57.2 8.6 57.15 22.225
90L 145 90 140 125 56 10 50 24
(3.5) (5.5) (5) (2.25) (0.34) (2.25) (0.875)
114.3 190.5 114.3 69.9 10.4 69.85 28.575
112S 182 112 190 114 70 12 60 28
(4.5) (7.5) (4.5) (2.75) (0.41) (2.75) (1.125)
114.3 190.5 139.7 69.9 10.4 69.85 28.575
112M 184 112 190 140 70 12 60 28
(4.5) (7.5) (5.5) (2.75) (0.41) (2.75) (1.125)
133.4 215.9 139.7 88.9 10.4 85.852 34.925
132S 213 132 216 140 89 12 80 38
(5.25) (8.5) (5.5) (3.5) (0.41) (3.38) (1.375)
133.4 215.9 177.8 88.9 10.4 85.852 34.925
132M 215 132 216 178 89 12 80 38
(5.25) (8.5) (7) (3.5) (0.41) (3.38) (1.375)
158.8 254 209.6 108 13.5 101.6 41.275
160M 254 160 254 210 108 14.5 110 42
(6.25) (10) (8.25) (4.25) (0.53) (4) (1.625)
158.8 254 254 108 13.5 101.6 41.275
160L 256 160 254 254 108 14.5 110 42
(6.25) (10) (10) (4.25) (0.53) (4) (1.625)
177.8 279.4 241.3 120.6 13.5 117.348 47.625
180M 284 180 279 241 121 14.5 110 48
(7) (11) (9.5) (4.75) (0.53) (4.62) (1.875)
177.8 279.4 279.4 120.6 13.5 117.348 47.625
180L 286 180 279 279 121 14.5 110 48
(7) (11) (11) (4.75) (0.53) (4.62) (1.875)
203.2 317.5 266.7 133.4 16.8 133.35 53.975
200M 324 200 318 267 133 18.5 110 55
(8) (12.5) (10.5) (5.25) (0.66) (5.25) (2.125)
203.2 317.5 304.8 133.4 16.8 133.35 53.975
200L 326 200 318 305 133 18.5 110 55
(8) (12.5) (12) (5.25) (0.66) (5.25) (2.125)
228.6 355.6 285.6 149.4 16.8 149.352 60.325
225S 364 225 356 286 149 18.5 140 60
(9) (14) (11.25) (5.88) (0.66) (5.88) (2.375)
228.6 355.6 311.2 149.4 16.8 149.352 60.325
225M 365 225 356 311 149 18.5 140 60
(9) (14) (12.25) (5.88) (0.66) (5.88) (2.375)
254 406.4 311.2 168.1 20.6 184.15 73.025
250S 404 250 406 311 168 24 140 65
(10) (16) (12.25) (6.62) (0.81) (7.25) (2.875)
254 406.4 349.2 168.1 20.6 184.15 73.025
250M 405 250 406 349 168 24 140 65
(10) (16) (13.75) (6.62) (0.81) (7.25) (2.875)
279.4 457.2 368.3 190.5 20.6 215.9 85.725
280S 444 280 457 368 190 24 140 75
(11) (18) (14.5) (7.5) (0.81) (8.5) (3.375)
279.4 457.2 419.1 190.5 20.6 215.9 85.725
280M 445 280 457 419 190 24 140 75
(11) (18) (16.5) (7.5) (0.81) (8.5) (3.375)
317.5 508 406.4 215.9
315S 504 315 508 406 216 28 – – – – –
(12.5) (20) (16) (8.5)
317.5 508 457.2 215.9
315M 505 315 508 457 216 28 – – – – –
(12.5) (20) (18) (8.5)
Important Note: The shaft extension indicated above for NEMA pertains to ‘T-shaft extension’.

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
ANNEXURE B
HISTORY INDICATING THE FRAME SIZE REDUCTION, FOR NEMA AC MOTORS

Table 49 - OPEN DRIP-PROOF

THREE PHASE FRAME SIZES - GENERAL PURPOSE
RPM 3600 1800 1200 900
NEMA
1952 1964 1952 1964 1952 1964 1952 1964
Program Orig. Orig. Orig. Orig.
Rerate Rerate Rerate Rerate Rerate Rerate Rerate Rerate
HP
1 – – – 203 182 143T 204 184 145T 225 213 182T
1.5 203 182 143T 204 184 145T 224 184 182T 254 213 184T
2 204 184 145T 224 184 145T 225 213 184T 254 215 213T
3 224 184 145T 225 213 182T 254 215 213T 284 254U 215T
10.49
5 225 213 182T 254 215 184T 284 254U 215T 324 256U 254T
7.5 254 215 184T 284 254U 213T 324 256U 254T 326 284U 256T

Selection & Application Guide

10 284 254U 213T 324 256U 215T 326 284U 256T 364 286U 284T
15 324 256U 215T 326 284U 254T 364 324U 284T 365 326U 286T
20 326 284U 254T 364 286U 256T 365 326U 286T 404 364U 324T
25 364S 286U 256T 364 324U 284T 404 364U 324T 405 365U 326T
30 364S 324S 284TS 365 326U 286T 405 365U 326T 444 404U 364T
40 365S 326S 286TS 404 364U 324T 444 404U 364T 445 405U 365T
50 404S 364S 324TS 405S 365US 326T 445 405U 365T 504U 444U 404T
60 405S 365US 326TS 444S 404US 364T 504U 444U 404T 505 445U 405T
75 444S 404US 364TS 445S 405US 365T 505 445U 405T – – 444T
100 445S 405US 365TS 504S 444US 404T – – 444T – – 445T
125 504S 444US 404TS 505S 445US 405T – – 445T – – –
150 505S 445US 405TS – – 444T – – – – – –
200 – – 444TS – – 445T – – – – – –
250 – – 445TS – – – – – – – – –

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

 AC Motor Selection & Application Guide
ANNEXURE B
HISTORY INDICATING THE FRAME SIZE REDUCTION, FOR NEMA AC MOTORS

Table 50 - TOTALLY ENCLOSED FAN COOLED

THREE PHASE FRAME SIZES - GENERAL PURPOSE
RPM 3600 1800 1200 900
NEMA
1952 1964 1952 1964 1952 1964 1952 1964
Program Orig. Orig. Orig. Orig.
Rerate Rerate Rerate Rerate Rerate Rerate Rerate Rerate
HP
1 – – – 203 182 143T 204 184 145T 225 213 182T
1.5 203 182 143T 204 184 145T 224 184 182T 254 213 184T
2 204 184 145T 224 184 145T 225 213 184T 254 215 213T
3 224 184 182T 225 213 182T 254 215 213T 284 254U 215T
10.50
5 225 213 184T 254 215 184T 284 254U 215T 324 256U 254T
7.5 254 215 213T 284 254U 213T 324 256U 254T 326 284U 256T
Selection & Application Guide

10 284 254U 215T 324 256U 215T 326 284U 256T 364 286U 284T
15 324 256U 254T 326 284U 254T 364 324U 284T 365 326U 286T
20 326 286U 256T 364 286U 256T 365 326U 286T 404 364U 324T
25 365S 324U 284TS 365 324U 284T 404 364U 324T 405 365U 326T
30 404S 326S 286TS 404 326U 286T 405 365U 326T 444 404U 364T
40 405S 364US 324TS 405 364U 324T 444 404U 364T 445 405U 365T
50 444S 365US 326TS 444S 365US 326T 445 405U 365T 504U 444U 404T
60 445S 405US 364TS 445S 405US 364T 504U 444U 404T 505 445U 405T
75 504S 444US 365TS 504S 444US 365T 505 445U 405T – – 444T
100 505S 445US 405TS 505S 445US 405T – – 444T – – 445T
125 – – 444TS – – 444T – – 445T – – –
150 – – 445TS – – 445T – – – – – –

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 AC Motor Selection & Application Guide
REFERENCES
National Electrical Code® and NEC®, terms used throughout this
publication are Registered Trademarks of the National Fire
Protection Agency, Inc., Quincy Mass.

NEMA Standards Publication No: MG-1 –2006

National Electrical Manufacturers Association
2101 L Street, N. W.
Washington, DC 20037
United States.

IEC 60034-1, Edition 11.0 2004-04

INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Central Office
3, rue de Varembé
P.O. Box 131 10.51
CH - 1211 GENEVA 20
Switzerland

Selection & Application Guide

ELECTRICAL APPARATUS SERVICE ASSOCIATION, INC.
1331 Baur Blvd.,
St. Louis, MO 63132-1986
Phone: 001-314-993-2220
Fax: 001-314-993-1269
www.easa.com

NOTES:

Data subject to change without notice. GEP-500T 02/08. www.gemotors.com

10.52

www.gemotors.com Data subject to change without notice. GEP-500T 02/08.

 UL/CSA Motor Listings

The UL/CSA listings below are blanket file numbers. Refer to the Company for specific volume
and section numbers. Where multiple files are shown, refer to the company for specific model.

UL File Number CSA File Number

Product
GE Frame (Motors) Motor Insulation Explosion Motor Explosion Energy
Category Motors
Components System Proof Protectors Proof Efficiency
From W, T & J E46994 E25382 MC161838
E203455
APPLIANCE

(Impedance) &
81 MM & 92MM MC213705
E14133
E214391 (Overloads) NA NA
E47088
122MM E14133 NA
NA
BPA -34, 48 & 56
MC161850
BC56 & 48
BC--48-49 & 58-59 - - 48-
AU1851
DC & EV

56 PM
BT13 Series AU1840 NA
NA NA NA
BC-42-46 & BC 40-70 E25899
NA NA
BT13 Series E182709
CD12 Series E79538 E214391 NA
143-449 E25900
LR78387 &
INDUSTRIAL

182T-326T E47088 E37792 E125132 MC161841 MC161841 LR78388 &

LR109509
143-449 (CUL) E219304
188AT-2110 (DC) NA E29056 MC161841 NA
11.1

UL/CSA Motor Listings

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

11.2

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 GE Motors Terms and Conditions of Sale

All orders are subject to acceptance by the General Electric Company, acting solely through and on behalf of its GE
Consumer & Industrial – Motors business component (Seller). Acceptance by Seller of any order and sale of any product
or service by Seller are expressly conditioned upon Buyer’s assent to the terms and conditions contained herein. Seller
expressly objects to any additional or different terms proposed by Buyer and such terms shall not be binding upon Seller
unless specifically agreed in writing by Seller’s authorized representative.

1.0. QUOTATIONS AND PUBLISHED PRICES one year from such transfer or lease or eighteen months from shipment
Seller’s quotation automatically expires forty-five calendar days from the date by Seller, whichever occurs first.
issued unless otherwise specified in such quotation and is subject to 3.2 Seller does not warrant the products or any repaired or replacement parts
withdrawal by Seller’s notice within that period. Seller reserves the right to against normal wear and tear, including that due to environment or
unilaterally extend its quotation for up to six months. Prices shown on price operation, including excessive operation at or beyond peak capability,
lists and published materials are not unconditional offers to sell and are subject frequent starting, type of fuel, detrimental air inlet conditions or erosion,
to change without notice. corrosion or material deposits from fluids or products which have been
involved in an accident. The conditions of any tests shall be mutually
2.0. PAYMENTS AND FINANCIAL CONDITION agreed upon and Seller shall be notified of, and may be represented at, all
2.1 Except as otherwise specified herein and/or in Seller’s quotation, payment tests that may be made. The warranties and remedies set forth herein
terms are net 30 days from date of Seller’s invoice. Past due amounts are are conditioned upon (a) proper storage, installation, use and
subject to a late payment fee of 1.0% per calendar month or fraction maintenance, and conformance with any applicable recommendations of
thereof. Payment shall be made by electronic funds transfer or other Seller and (b) Buyer promptly notifying Seller of any defects and, if
method acceptable to Seller. Seller does not accept and Buyer shall not required, promptly making the product available for correction.
make payments in currency. 3.3 If any product or service fails to meet the foregoing warranties (except title),
2.2 Except as otherwise specified in Seller’s quotation, payment is due and Seller shall thereupon correct any such failure at its option, by (i) repairing
Seller may issue invoices for pro rata payments without setoff as any defective or damaged part or parts of the products, or (ii) making
shipments are made. If Seller consents to delay a shipment after available any necessary repaired or replacement parts or necessary service
completion of any product or if Buyer causes delay in a shipment, Seller that will be performed during normal working hours on a straight time basis.
may issue its invoice on the date when Seller is prepared to make Repaired or replaced products will be returned FCA Seller’s plant or other
shipment. In the event of any such delay, title shall pass and products Point of Shipment (INCOTERMS 2000) determined by Seller. Buyer shall pay
shall be held at Buyer’s risk and expense. If the cost to the Seller of in-bound and out-bound transportation charges and for services of any
production, delivery, or installation of such products is increased by kind, including removal of the defective or damaged part or parts,
reason of delays caused by the Buyer, such additional expense incurred installation of the repaired or replacement part or parts, or other services.
by the Seller shall be paid by the Buyer. Where a failure cannot be corrected by Seller’s reasonable efforts, the
2.3 Notwithstanding Sub-Articles 2.1 and 2.2, with respect to items having a parties will negotiate an equitable adjustment in price.
price equal to or greater than $250,000 USD, a 10% down payment shall 3.4 Sub-Article 3.3 sets forth the exclusive remedies for claims (except as to
be due and Seller may issue its invoice for such down payment at time of title) based on defect in or failure or nonconformity of products or
order placement with respect to each such item, with 90% payable in services, whether the claim is in contract, indemnity, warranty, tort (in-
progress payments in equal monthly payments, with the first progress cluding Seller’s negligence), strict liability or otherwise and however
payment due no later than one (1) month after receipt of the order and instituted. Upon the expiration of the warranty period, all such liability
the last progress payment due on the anniversary of the receipt of the shall terminate and Buyer shall have a reasonable time, within thirty days
order in the month in which Seller delivers the item. after the warranty period, to give written notice of any defects that
2.4 Any order for products by Buyer shall constitute a representation that appeared during the warranty period.
Buyer is solvent. In addition, upon Seller’s request, Buyer will furnish a 3.5 EXCEPT AS SET FORTH IN ARTICLE 4.0 “PATENTS,” THE FOREGOING
written representation concerning its solvency at any time prior to WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
shipment. WHETHER WRITTEN, ORAL, IMPLIED OR STATUTORY. NO IMPLIED
2.5 If Buyer’s financial condition at any time does not justify continuance of STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
the work to be performed by Seller hereunder on the agreed terms of PARTICULAR PURPOSE SHALL APPLY. SELLER DOES NOT WARRANT ANY
payment, or if Buyer fails to fulfill its payment obligations, Seller may PRODUCTS OR SERVICES OF OTHERS THAT BUYER HAS DESIGNATED.
require full or partial payment in advance before proceeding with any
further activities related to the products or services to be supplied. The 4.0 PATENTS
4.1 Subject to the provisions of this article, Seller warrants that products
12.1
Buyer shall compensate Seller for costs incurred related to said non-
fulfillment or financial condition and shall grant an extension of time for furnished hereunder, and any part thereof, shall be delivered free of any
Seller’s performance equal in duration to the period of non-fulfillment or rightful claim of any third party for infringement of any United States
financial condition. In the event of Buyer’s bankruptcy or insolvency or in patent. If notified promptly in writing and given authority, information

Terms and Conditions

the event any proceeding is brought against Buyer, voluntarily or and assistance, and contingent upon Buyer not taking any position
involuntarily, under the bankruptcy or any insolvency laws, Seller shall be adverse to Seller in connection with such claim, Seller shall defend, or may
entitled to cancel any agreement then outstanding at any time during the settle, at its expense, any suit or proceeding against Buyer so far as based
period allowed for filing claims against the estate and shall receive on a claimed infringement which would result in a breach of this warranty
reimbursement for its proper cancellation charges. Seller’s rights under and Seller shall pay all damages and costs awarded therein against Buyer
this article are in addition to all rights available to it at law or in equity. due to such breach. In case any product or part thereof is in such suit
2.6 At the request of the Seller, payments shall be made by an irrevocable held to constitute such an infringement and the use for the purpose
Letter of Credit established by the Buyer in favor of and acceptable to the intended of said product or part is enjoined, Seller shall, at its expense and
Seller and confirmed by a bank satisfactory to the Seller. Seller may option, either procure for Buyer the right to continue using said product or
make such request prior to Seller’s acceptance of Buyer’s order or on the part, or replace same with a non-infringing product or part, or modify
occurrence of the conditions described in Sub-Article 2.5 hereof. same so it becomes noninfringing, or remove the product and refund the
purchase price (less reasonable depreciation for any period of use) and
3.0 WARRANTIES any transportation costs separately paid by Buyer. The foregoing states
3.1 Seller warrants to Buyer that unless otherwise stated by Seller, any the entire liability of Seller for patent infringement by said products or any
products and/or any services furnished hereunder will be free from part thereof.
defects in material, workmanship and title and will be of the kind and 4.2 Sub-Article 4.1 shall not apply to any product or part specified by Buyer
quality specified in Seller’s written quotation. This warranty shall apply or manufactured to Buyer’s design, or to the use of any product furnished
only to failures to meet said warranties (excluding any defects in title) that hereunder in conjunction with any other product in a combination not
appear within one year from the date of shipment hereunder; provided, furnished by Seller as a part of this transaction. As to any such product,
however, that if Buyer, in the course of its regular and usual business, part, or use in such combination, Seller assumes no liability whatsoever
transfers title to or leases such products (including equipment for patent infringement and Buyer will hold Seller harmless against any
incorporating such products) to a third party, such period shall run until infringement claims arising therefrom.

Data subject to change without notice. GEP-973H (12/07). www.gemotors.com

 Terms and Conditions

5.0 DELIVERY, TITLE, AND RISK OF LOSS 7.0 CONFIDENTIALITY

5.1 Delivery dates are approximate and are based upon Seller’s prompt Any information, suggestions, or ideas transmitted by Buyer to Seller in
receipt of all necessary information from Buyer. Seller reserves the right connection with performance hereunder are not to be regarded as secret or
to adjust delivery dates based upon changes in its factory loading. Unless submitted in confidence except as may be otherwise provided in a writing
otherwise specified by Seller, delivery will be made to Buyer FCA Point of signed by a duly authorized representative of Seller.
Shipment (INCOTERMS 2000). Partial shipments are allowed. Title and risk
of loss or damage shall pass on delivery. 8.0 TAXES
5.2 Point of Shipment will be factory of origin, unless (a) the required product 8.1 In addition to any price specified herein, Buyer shall pay the gross
is available at a warehouse and can be more conveniently delivered from amount of any present or future sales, use, excise, value-added, business
such warehouse; in which case, Point of Shipment shall be such ware- transfer or other similar tax applicable to the price, sale or delivery of any
house or (b) Seller can more conveniently deliver the required product at products or services furnished hereunder or to their use by Seller or Buyer,
another location, in which case, Point of Shipment shall be such location. or Buyer shall furnish Seller evidence of exemption acceptable to the
Point of Shipment shall be determined in each case by Seller. taxing authorities. If any such taxes referred to in the preceding sentence
5.3 Seller will select the following as it deems necessary to deliver the product are included in the price, the prices shall be adjusted to reflect any
FCA Point of Shipment (INCOTERMS 2000): (1) method of transportation; (2) changes subsequent to the date of the proposal in such taxes including,
routing of shipment; (3) Point of Shipment; (4) choice of carrier; and (5) but not limited to, changes in the rate and amount. All amounts to be
timing of shipment. Routing of shipment may require the use of rail, truck, paid by the Buyer are payable as invoiced.
water or air transport. When, at Buyer’s request, shipment is other than 8.2 Any taxes (including income, sales, stamp and turnover or value-added
as selected by Seller with respect to items (1) through (5) above, all freight taxes), duties, fees, charges or assessments of any nature levied by any
and/or handling charges will be to Buyer’s account. In addition, any governmental authority in connection with this transaction, whether
expense incurred by Seller because of special delivery arrangements levied against Buyer, against Seller or its employees or against any of
requested by Buyer shall be billed to Buyer. Seller’s subcontractors or their employees, shall be the responsibility of
5.4 If shipment of the products or any part thereof is delayed by an act, the Buyer and shall be paid directly by the Buyer to the governmental
request or omission of the Buyer or due to an Excusable Delay, as defined authority concerned. If Seller or its subcontractors, or the employees of
herein, the Seller may place such products into storage (which may be at either, are required to pay any such levies and/or fines, penalties, or
the place of manufacture, Seller’s warehouse, or other Point of Shipment, assessments in the first instance, or as a result of Buyer’s failure to
or a third party storage provider) immediately upon the expiration of a comply with any applicable laws or regulations governing the payment of
two week period after the delivery date if Buyer has not, by that time, such levies by Buyer, the amount of any payments so made, plus the
provided sufficient information and taken the necessary actions to enable expense of currency conversion, shall be promptly reimbursed in US
Seller to deliver the products in accordance with the agreement. In such Dollars by Buyer upon submission of Seller’s invoices therefor.
event,
(i) Seller’s shipment obligation shall be deemed fulfilled and risk of loss 9.0 LIMITATIONS OF LIABILITIES, DISCLAIMER OF DAMAGES, AND
and damage shall pass to Buyer. INDEMNITIES
(ii) any amounts payable to Seller on delivery shall be payable upon
9.1 Subject to the other provisions of this article, Seller agrees to indemnify
presentation of Seller’s related invoices, and, upon payment, title
and save harmless Buyer from and against any loss, expense or claim
passes.
asserted by third parties for damage to third party tangible property, or
(iii) all expenses incurred by Seller, including, but not limited to, all
for bodily injury, or both, arising out of the performance of this
expenses of preparation and shipment into storage, handling,
agreement, to the extent such damage or injury is attributable to the
storage, inspection, preservation and insurance shall be for Buyer’s
negligence of Seller; provided that Buyer gives Seller prompt notice of any
account and shall be payable upon Seller’s presentation of related
such claim and all necessary information and assistance so that Seller, at
invoices.
its option, may defend or settle such claim and Buyer does not take any
adverse position in connection with such claim. In the event that any
12.2 6.0 EXCUSABLE DELAY such damage or injury is caused by the joint or concurrent negligence of
6.1 The Seller shall not be in breach of any of its obligations under this Seller and Buyer, the loss, expense or claim shall be borne by Seller and
contract where failure to perform or delay in performing any obligation is Buyer in proportion to their negligence.
due, wholly or in part, to (i) a cause beyond its reasonable control, (ii) an 9.2 Except as provided in Article 4.0, “Patents,” in no event, whether as a result
act of God, an act or omission of the Buyer or of any governmental of breach of contract, indemnity, warranty, tort (including Seller’s
Terms and Conditions

authority, governmental priorities, riots, strikes or other labor disputes, negligence), strict liability or otherwise, shall Seller’s liability to Buyer or its
fires, flood, sabotage, earthquake, storm, epidemic, or (iii) inability due to a insurers for any loss or damage arising out of, or resulting from this
cause beyond the Seller’s reasonable control to obtain necessary or agreement, or from its performance or breach, or from the products or
proper labor, materials, components, facilities, energy, fuel, transportation, services furnished hereunder, exceed the price of the specific product or
required instructions or information from the Buyer. The foregoing shall service which gives rise to the claim, and except as to title, any such
apply even though any such cause exists at the time of the order or liability shall terminate upon the expiration of the warranty period
occurs after the Seller’s performance of its obligations is delayed by specified in Article 3.0, “Warranties”. Any such claim of liability must be
another cause. timely commenced in a court of competent jurisdiction in accordance
6.2 The Seller will notify the Buyer promptly of any failure to perform or delay with the applicable statute of limitations and/or of repose, but in no event
in performing due to a cause set out in Sub-Article 6.1 and shall specify, later than one year from the termination of the warranty period.
as soon as practicable, when the obligation will be performed. Subject to 9.3 IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT,
Sub-Article 6.3, the time for performing the obligation shall be extended INDEMNITY, WARRANTY, TORT (INCLUDING SELLER’S NEGLIGENCE),
for the period lost due to such a cause. STRICT LIABILITY OR OTHERWISE, SHALL SELLER BE LIABLE FOR ANY
6.3 Where the period lost is at least 60 days and the parties have not agreed SPECIAL, CONSEQUENTIAL, INCIDENTAL OR PENAL DAMAGES
upon a revised basis for performing the obligation, including adjustment INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFIT OR REVENUES, LOSS
of the prices, then, either party may, upon 30 days written notice, OF USE OF THE PRODUCTS OR ANY ASSOCIATED EQUIPMENT, DAMAGE
terminate this contract whereupon the Buyer shall pay the Cancellation TO ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE
Charges determined in accordance with Sub-Article 13.0. PRODUCTS, FACILITIES, SERVICES OR REPLACEMENT POWER,

www.gemotors.com Data subject to change without notice. GEP-973H (12/07).

 Terms and Conditions

DOWNTIME COSTS, IN/OUT TRANSPORTATION CHARGES OR CLAIMS OF 12.0 PRICE ADJUSTMENT FOR SIGNIFICANT COST INCREASE
BUYER’S CUSTOMERS FOR SUCH DAMAGES. If the products or services 12.1 Prices shall be subject to adjustment by Seller to its standard prices
being provided by Seller will be furnished by Buyer to a third party by current at time of shipment or, at Seller’s option, price may be adjusted
contract or otherwise or relate to a contract between Buyer and a third where there is a “significant cost increase” in the aggregate cost of
party, Buyer shall obtain from such third party a provision affording Seller materials, components and labor between the time of Seller’s quote and
the protection of this article, except for Sub-Article 9.1. the time of delivery. A “significant cost increase” means a change in the
9.4 If Seller furnishes Buyer with advice or other assistance which concerns aggregate cost of the materials, components and labor from the date of
any product supplied hereunder or any system or equipment in which the proposal/quotation to the date of delivery by an amount equal to or
any such product may be installed and which is not required pursuant to greater than 2 percent (2%) as determined by Seller.
this agreement, the furnishing of such advice or assistance will not subject 12.2 Drawings:
Seller to any liability, whether in contract, indemnity, warranty, tort (i) If the Buyer requires that drawings be submitted for approval, the
(including Seller’s negligence), strict liability or otherwise. For the purposes Buyer must approve and return the drawings within sixty (60)
of Sub-Articles 9.2, 9.3, and 9.4 of this article, the term Seller includes calendar days of the Seller’s original email submission date with a
Seller’s subcontractors and suppliers. written notice calling for the immediate manufacturing release of the
products and shipment within the quoted manufacturing cycle time.
10.0 NO NUCLEAR USE (ii) In the event that Buyer for any reason does not comply with the
Products and Services sold by Seller are not intended for use in connection with condition in paragraph (i) above and/or shipment is delayed for any
any nuclear facility, application or activity without the written consent of Seller. reason not within the control of Seller, including, but not limited to,
Buyer warrants that it shall not use or permit others to use products or services lack of technical details, shipping information, commercial
purchased hereunder for such purposes, unless Seller agrees to the use in outstanding items, etc, the price shall be increased 1.5% for each full
writing. If Seller has reason to believe that Buyer or an intended subsequent calendar month or fraction thereof that shipment is delayed.
purchaser intends such use, in addition to any other legal or equitable rights of
Seller, Seller shall have the right to cancel this agreement and to recover the 13.0 CANCELLATION AND CANCELLATION CHARGES
cancellation charges set forth in Article 13.0 “CANCELLATION AND 13.1 The Buyer may cancel this agreement at any time upon written notice
CANCELLATION CHARGES.” If any such use occurs, Seller (and its parent, and payment to the Seller of the Cancellation Charges set forth below in
affiliates, suppliers and subcontractors) disclaims all liability for any nuclear or this article.
other damages, injury or contamination, and in addition to any other legal or 13.2 In the event that this agreement is canceled pursuant to Articles 2.0
equitable rights of Seller, Buyer shall indemnify and hold Seller (and its parent, PAYMENTS AND FINANCIAL CONDITION (by Seller for Buyer’s bankruptcy
affiliates, suppliers and subcontractors) harmless against any such liability. If or insolvency), 6.0 EXCUSABLE DELAY, 10.0 NO NUCLEAR USE (by Seller), or
Seller agrees in writing to any such use, the parties shall agree upon special this 13.0 Cancellation and Cancellation Charges, the cancellation charges
terms and conditions that provide Seller protections against nuclear liability payable by the Buyer to the Seller shall be calculated as follows:
and which are acceptable to Seller under the then current laws that apply. (i) Material, labor and indirect expenses committed or incurred to date
of cancellation;
11.0 GENERAL (ii) All costs incurred in the execution of the cancellation;
11.1 Any products delivered by Seller hereunder will be produced in (iii) Reasonable profit on (i) and (ii) hereinabove cited; and
compliance with the Fair Labor Standards Act of 1938, as amended and (iv) The greater of (a) 10% of the unbilled portion of the contract price,
applicable. Seller will comply with applicable federal, state and local laws and (b) all other expenses and costs incurred by the Seller reasonably
and regulations as of the date of any quotation which relate to (i) non- related to the cancellation.
segregated facilities and equal employment opportunity (including the 13.3 The cancellation charges shall be payable upon presentation of Seller’s
seven paragraphs appearing in Section 202 of Executive Order 11246, as invoice therefore.
amended), (ii) workers’ compensation, and (iii) the production in Seller’s
manufacturing facilities of products furnished hereunder. Price and, if 14.0 CHANGES
necessary, delivery will be equitably adjusted to compensate Seller for the 14.1 Buyer may change an agreement upon (a) written notice, (b) Seller’s 12.3
cost of compliance with any other laws or regulations. express written consent, and (c) payment to Seller of the change charges,
11.2 The delegation or assignment by Buyer of any or all of its duties or rights which shall include costs and expenses incurred for work and materials
hereunder without Seller’s prior written consent shall be void. unnecessary as a result of such changes and for work and materials
11.3 Any representation, warranty, course of dealing or trade usage not required to implement such changes.

Terms and Conditions

contained or referenced herein will not be binding on Seller. These Terms 14.2 The presentation by Buyer to Seller, following Seller’s proposal/quotation,
and Conditions of Sale contain the entire and only agreement between of additional or different information and/or instructions that materially
the Buyer and Seller respecting the terms and conditions and supersedes impact Seller’s cost and/or time to deliver products and/or services shall
and cancels all previous negotiations, agreements, commitments, comprise a proposed change. Buyer may make such change, subject to
representations and writings in respect thereto. These Terms and Sub-Article 14.1.
Conditions of Sale may not be amended, supplemented, changed or
modified in any manner, orally or otherwise, except by an instrument in 15.0 BUYER-FURNISHED ITEMS
writing of concurrent or subsequent date, signed by a duly authorized 15.1 If this agreement involves the purchase of a product in which Seller is to
representative of each party. incorporate a Buyer-furnished item or to which Seller is to mount a Buyer-
11.4 The validity, performance and all matters relating to the interpretation furnished item, Buyer shall make the Buyer-furnished item available, at
and effect of this agreement and any amendment hereto shall be Buyer’s cost, to Seller in accordance with Seller’s shipping instructions.
governed by the law of the State of New York, excluding its conflict of law 15.2 If Seller does not receive the Buyer-furnished item according to Seller’s
rules. The invalidity, in whole or part, of any of the articles in these Terms shipping instructions, Seller will continue to manufacture the product to
and Conditions of Sale will not affect the remainder of such article or any the extent possible.
other article. 15.3 If Seller does not receive the Buyer-furnished item according to Seller’s
11.5 The provisions of this agreement are for the benefit of the parties hereto shipping instructions and continuing the manufacture of the product
and not for any other person except as specifically provided herein. becomes impossible or impractical as a result and Buyer has not
11.6 The parties hereby expressly exclude the application of the United Nations requested shipment of the product without incorporation or mounting of
Convention on Contracts for the International Sale of Goods to this the Buyer-furnished item, Seller may bill Buyer the full price of the product
agreement. and place the product with a commercial storage provider immediately
upon the expiration of a two week period after the date on which Seller
gives notice to Buyer that continuing manufacture of the product is
impossible or impractical. In such event:

Data subject to change without notice. GEP-973H (12/07). www.gemotors.com

 Terms and Conditions

(i) Seller’s shipment obligation shall be deemed fulfilled and risk of loss 19.0 GOVERNMENT AUTHORIZATION
and damage shall pass to Buyer. 19.1 The party that arranges for export shipment (or Buyer’s designated export
(ii) any amounts payable to Seller on delivery shall be payable upon agent) shall be responsible for the timely application in its own name for
presentation of Seller’s related invoices, and, upon payment, title any required government export license. Buyer shall be responsible for
passes. timely obtaining and maintaining any required import license, exchange
(iii) all expenses incurred by Seller, including, but not limited to, all permit or any other governmental authorization. Buyer and Seller shall
expenses of preparation and shipment into storage, handling, assist each other when such help is reasonably possible. Seller shall not
storage, inspection, preservation and insurance shall be for Buyer’s be liable if any authorization of any government is delayed, denied,
account and shall be payable upon Seller’s presentation of related revoked, restricted or not renewed, and Buyer shall not be relieved
invoices. thereby of its obligations to pay Seller for its products or any other
15.4 Upon Seller’s receipt of the Buyer-furnished item, Buyer will arrange the charges which are the obligation of the Buyer hereunder.
transportation and shipment and return of the product to Seller’s factory 19.2 All shipments hereunder shall at all times be subject to US export control
to complete manufacturing. laws and regulations and any amendments thereto. Buyer agrees that it
15.5 Seller reserves the right to either rework or return Buyer-furnished items shall not make any disposition of US-origin products purchased from
that do not conform to applicable specifications when furnished by Buyer. Seller by way of trans-shipment, re-export, diversion or otherwise, other
If Seller elects to rework the item Buyer shall be responsible for the costs than in and to the ultimate country of destination specified on Buyer’s
of such rework. Upon Buyer’s approval, Seller will perform the rework and agreement or declared as the country of ultimate destination on Seller’s
invoice Buyer for such rework. invoices, except as said laws and regulations may expressly permit.

16.0 PACKING 20.0 SOFTWARE LICENSING AND WARRANTY

16.1 Prices are based on Seller’s standard packing and boxing for domestic US 20.1 Unless subject to a separate license or agreement, any software
shipment only. furnished hereunder whether separately or incorporated with supplied
16.2 Buyer shall be responsible for cost of packing and boxing other than hardware, including any subsequent updates, is furnished under the
Seller’s standard packing and boxing for domestic US shipment. Seller following terms and conditions.
may invoice Buyer for such costs as a separate and additional charge. (i) The software and any part thereof is designed to be used only on the
type product on which the software is first installed.
17.0 INSURANCE (ii) No exclusivity of use of the software is transferred to Buyer.
During the period between shipment (or if the product is installed by the Seller, (iii) Software and hardware documentation which is copyrighted by
from the time the product is turned over to the Buyer) and final payment for Seller shall not be copied in whole or in part, but additional copies of
the products, the Buyer will maintain sufficient insurance thereon in the name software and documentation in printed form may be obtained from
of the Seller against loss or damage from any cause to cover the unpaid Seller or its representatives at Seller’s then standard charges, subject
balance of the purchase price and failing to do so no loss or damage suffered to applicable import and export laws and regulations. Buyer agrees
during the aforesaid period shall relieve the Buyer from payment of the balance that any copyright, proprietary, trade secret or similar notices
of the purchase price or from any of the terms of this contract. During such appearing on and in software will be reproduced and included on
period, the Buyer will maintain the products and related materials delivered by and in any modifications and copies, in whole or in part, of software.
the Seller in good condition. (iv) The source code for software is not included unless specifically listed
as an item in Seller’s specification.
18.0 EXPORT AND IMPORT (v) On the occasion that third party licensed software is provided, it will
18.1 In the absence of an agreement to the contrary, the Buyer shall arrange be identified as such and the Buyer will be required to complete any
for (i) export shipment to Buyer’s country and (ii) marine warehouse-to- sublicense specified by the software licensor and provided by the
warehouse insurance (including war risk, if available). If the Seller Seller.
performs any, or all, of the aforementioned export shipment (vi) If a separate software license agreement is required by Seller, Buyer
12.4 arrangements, the Buyer shall pay Seller for all related fees and expenses, shall execute the software license agreement on or before
including, but not limited to, those covering preparation of consular installation, and the provisions of the separate software license
documents, consular fees, ocean freight, storage, insurance and Seller’s agreement shall supersede the foregoing sub-articles to the extent
then current fee for such services upon submission of Seller’s invoices they are inconsistent with such license.
therefor. 20.2 Article 3.0 “WARRANTY” shall not apply to software. The warranty for
Terms and Conditions

18.2 In performing any of the foregoing services, Seller shall comply with any software shall be as set out in a separate software warranty to be
reasonable instructions of Buyer or, in the absence thereof, shall act provided to Buyer by Seller.
according to its best judgment. In so acting on Buyer’s behalf, neither
Seller nor its agents shall be liable for fines or other charges due to 21.0 CONFORMANCE WITH REGULATIONS
incorrect declarations or for negligence or for any special, consequential, AND/OR STANDARDS
incidental, indirect or exemplary damages to Buyer resulting therefrom. The Seller takes reasonable steps to keep its products in conformance with
18.3 Buyer shall be the importer of record for any products sold hereunder and various recognized standards and such regulations as may affect its products;
shall be responsible for complying with all applicable laws relating to the however, the Seller recognizes that its products are used in many regulated
importation of the products (“Import Laws”). Without limiting the applications and that, from time to time, standards and regulations conflict
generality of the foregoing, Buyer shall pay any charges on importation of with each other. The Seller makes no promise or representation that its product
the products, except as may be otherwise expressly agreed to in writing will conform to any federal, state or local laws, ordinances, regulation, codes or
in the agreement by Seller, and shall make any arrangements and provide standards, except as particularly specified and agreed upon in a signed written
any documentation required by the applicable import laws with respect to agreement between Buyer and Seller and as indicated in the nameplate affixed
importation of such products. to the product. The Seller’s prices do not include the cost of any related
18.4 Buyer shall be the importer of record for any Buyer-furnished item sent to inspections or permits or inspection fees.
Seller to be used in the performance of this agreement and shall be
responsible for complying with applicable import laws applicable to such
Buyer-furnished item. Without limiting the generality of the foregoing,
Buyer shall pay any charges on importation of the Buyer-furnished item,
and shall make any arrangements and provide any documentation
required by applicable import laws with respect to importation of such
Buyer-furnished item.

www.gemotors.com Data subject to change without notice. GEP-973H (12/07).

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number 13.1
1232 5KSM92KFL3006S 7 $167 G3-1CON 8.2 A106 249A9598AA7 $105 GO-1R 1.22
1331 5KSM92KFL2011S 7 $156 G3-1CON 8.2 A106 249A9598AA7 $105 GO-1R 2.11
1332 5KSM92KFL2007S 7 $159 G3-1CON 8.2 A106 249A9598AA7 $105 GO-1R 3.35

Cross Reference Guide

1336 5KSM92KFL2008S 9 $94 G3-1CON 8.2 A107 249A9598AA8 $105 GO-1R 1.22
1341 5KSM92HFL2004S 9 $156 G3-1CON 8.2 A107 249A9598AA8 $105 GO-1R 2.11
1342 5KSM92KFL2012S 7 $159 G3-1CON 8.2 A107 249A9598AA8 $105 GO-1R 3.35
1431 5KSM92KFL2005S 6 $137 G3-1CON 8.2 A108 249A9598AA9 $186 GO-1R 1.22
1432 5KSM92KFL2009S 7 $140 G3-1CON 8.2 A108 249A9598AA9 $186 GO-1R 2.11
1441 5KSM92KFL2003S 7 $137 G3-1CON 8.2 A108 249A9598AA9 $186 GO-1R 3.35
1442 5KSM92KFL1009S 9 $140 G3-1CON 8.2 A233 153B1073BEG01 $107 G4-7KITS 1.22
5108 5KSM81FFL0068 2 $27 G3-1CON 8.3 A233 153B1073BEG01 $107 G4-7KITS 2.11
5109 5KSM81FFL0065 4 $22 G3-1CON 8.3 A233 153B1073BEG01 $107 G4-7KITS 3.34
5111 5KSM81HFL0007 2 $30 G3-1CON 8.3 A233 153B1073BEG01 $107 G4-7KITS 4.6
5113 5KSM81FFL0002 2 $28 G3-1CON 8.3 A234 153B1069AAG01 $111 G4-7KITS 1.22
5211 5KSM81HFL0008 2 $28 G3-1CON 8.3 A234 153B1069AAG01 $111 G4-7KITS 2.11
5212 5KSM81HFL0009 2 $28 G3-1CON 8.3 A234 153B1069AAG01 $111 G4-7KITS 3.34
5213 5KSM81FFL0003 2 $25 G3-1CON 8.3 A234 153B1069AAG01 $111 G4-7KITS 4.6
5214 5KSM81FFL0004 2 $25 G3-1CON 8.3 A235 153B1069AAG02 $111 G4-7KITS 1.22
5221 5KSM81HFL0010 3 $30 G3-1CON 8.3 A235 153B1069AAG02 $111 G4-7KITS 2.11
5222 5KSM81HFL0011 3 $30 G3-1CON 8.3 A235 153B1069AAG02 $111 G4-7KITS 3.34
5223 5KSM81FFL0005 2 $27 G3-1CON 8.3 A235 153B1069AAG02 $111 G4-7KITS 4.6
5224 5KSM81FFL0006 2 $27 G3-1CON 8.3 A236 153B1069AAG03 $111 G4-7KITS 1.22
5311 5KSM81HFL1007 3 $30 G3-1CON 8.3 A236 153B1069AAG03 $111 G4-7KITS 2.11
5312 5KSM81HFL1008 4 $30 G3-1CON 8.3 A236 153B1069AAG03 $111 G4-7KITS 3.34
5313 5KSM81FFL1002 2 $27 G3-1CON 8.3 A236 153B1069AAG03 $111 G4-7KITS 4.6
5314 5KSM81FFL1003 2 $27 G3-1CON 8.3 A237 153B1069ANG01 $188 G4-7KITS 1.22
5315 5KPM81HFL0095 2 $34 G3-1CON 8.3 A237 153B1069ANG01 $188 G4-7KITS 2.11
5325 5KPM81HFL0096 2 $36 G3-1CON 8.3 A237 153B1069ANG01 $188 G4-7KITS 3.34
5335 5KPM81HFL0097 2 $34 G3-1CON 8.3 A237 153B1069ANG01 $188 G4-7KITS 4.6
5345 5KPM81HFL0098 2 $36 G3-1CON 8.3 A238 153B1069ANG05 $188 G4-7KITS 1.22
5411 5KSM81HFL1001 3 $31 G3-1CON 8.3 A238 153B1069ANG05 $188 G4-7KITS 2.11
5412 5KSM81HFL1009 3 $31 G3-1CON 8.3 A238 153B1069ANG05 $188 G4-7KITS 3.34
5413 5KSM81FFL1000 2 $28 G3-1CON 8.3 A238 153B1069ANG05 $188 G4-7KITS 4.6
5414 5KSM81FFL1004 2 $28 G3-1CON 8.3 A239 153B1073BDG02 $107 G4-7KITS 1.22
5415 5KPM81HFL1086 3 $40 G3-1CON 8.3 A239 153B1073BDG02 $107 G4-7KITS 2.11
5421 5KSM81HFL1010 3 $33 G3-1CON 8.3 A239 153B1073BDG02 $107 G4-7KITS 3.34
5422 5KSM81HFL1011 3 $33 G3-1CON 8.3 A239 153B1073BDG02 $107 G4-7KITS 4.6
5423 5KSM81FFL1005 2 $30 G3-1CON 8.3 A240 153B1069ANG03 $188 G4-7KITS 1.22
5424 5KSM81FFL1006 2 $30 G3-1CON 8.3 A240 153B1069ANG03 $188 G4-7KITS 3.34
5425 5KPM81HFL1087 3 $42 G3-1CON 8.3 A240 153B1069ANG03 $188 G4-7KITS 4.6
5435 5KPM81HFL1088 3 $40 G3-1CON 8.3 A241 153B1069ANG02 $203 G4-7KITS 1.22
5445 5KPM81HFL1089 3 $42 G3-1CON 8.3 A241 153B1069ANG02 $203 G4-7KITS 2.11
5811 5KSM81HFL3004T 4 $42 G3-1CON 8.3 A241 153B1069ANG02 $203 G4-7KITS 3.34
5812 5KSM81HFL3005T 4 $42 G3-1CON 8.3 A241 153B1069ANG02 $203 G4-7KITS 4.6
5813 5KSM81FFL3000S 3 $36 G3-1CON 8.3 A242 153B1069ANG06 $203 G4-7KITS 1.22
5814 5KSM81FFL3001S 3 $36 G3-1CON 8.3 A242 153B1069ANG06 $203 G4-7KITS 2.11
5815 5KPM81HFL3046S 4 $45 G3-1CON 8.3 A242 153B1069ANG06 $203 G4-7KITS 3.34
5821 5KSM81HFL3006T 4 $44 G3-1CON 8.3 A242 153B1069ANG06 $203 G4-7KITS 4.6
5822 5KSM81HFL3007T 6 $44 G3-1CON 8.3 A244 153B1069ANG04 $203 G4-7KITS 1.22
5823 5KSM81FFL3002S 3 $38 G3-1CON 8.3 A244 153B1069ANG04 $203 G4-7KITS 2.11
5824 5KSM81FFL3003S 3 $38 G3-1CON 8.3 A244 153B1069ANG04 $203 G4-7KITS 3.34
5825 5KPM81HFL3047S 4 $47 G3-1CON 8.3 A244 153B1069ANG04 $203 G4-7KITS 4.6
5835 5KPM81HFL3048S 4 $45 G3-1CON 8.3 A249 CAT#A249 $188 G4-7KITS 2.11
5845 5KPM81HFL3049S 4 $47 G3-1CON 8.3 A268 249A9500ABPT4 $169 G4-7KITS 1.20
A100 249A9598AA1 $60 GO-1R 1.22 A269 249A9500ABPT6 $258 G4-7KITS 1.20
A100 249A9598AA1 $60 GO-1R 2.11 A270 249A9500ABPT5 $258 G4-7KITS 1.20
A100 249A9598AA1 $60 GO-1R 3.35 A272 249A9500AAPT21 $98 G4-7KITS 1.21
A101 249A9598AA2 $60 GO-1R 1.22 A274 249A9500AAPT22 $134 G4-7KITS 1.21
A101 249A9598AA2 $60 GO-1R 2.11 A280 249A9500AAPT23 $167 G4-7KITS 1.21
A101 249A9598AA2 $60 GO-1R 3.35 A281 249A9500AAPT24 $224 G4-7KITS 1.21
A102 249A9598AA3 $71 GO-1R 1.22 A282 249A9500AAPT6 $224 G4-7KITS 1.21
A102 249A9598AA3 $71 GO-1R 2.11 A283 249A9500AAPT25 $297 G4-7KITS 1.21
A102 249A9598AA3 $71 GO-1R 3.35 A284 235A4753BF1 $339 G4-7KITS 3.35
A103 249A9598AA4 $71 GO-1R 1.22 A285 235A4753BF2 $339 G4-7KITS 3.35
A103 249A9598AA4 $71 GO-1R 2.11 A286 235A4753BF4 $339 G4-7KITS 3.35
A103 249A9598AA4 $71 GO-1R 3.35 A287 235A4753BG1 $405 G4-7KITS 3.35
A104 249A9598AA5 $91 GO-1R 1.22 A288 235A4753BG2 $405 G4-7KITS 3.35
A104 249A9598AA5 $91 GO-1R 2.11 A289 235A4753BG3 $405 G4-7KITS 3.35
A104 249A9598AA5 $91 GO-1R 3.35 A290 235A4753BH1 $405 G4-7KITS 3.35
A105 249A9598AA6 $91 GO-1R 1.22 A291 235A4753BH2 $405 G4-7KITS 3.35
A105 249A9598AA6 $91 GO-1R 2.11 A292 235A4753BH3 $405 G4-7KITS 3.35
A105 249A9598AA6 $91 GO-1R 3.35 A293 235A4753BJ1 $480 G4-7KITS 3.35

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.2 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
A294 235A4753BJ2 $480 G4-7KITS 3.35 A763 249A4321AMG03 $561 G4-7KITS 3.33
A295 235A4753BJ3 $480 G4-7KITS 3.35 A764 249A4321AMG04 $561 G4-7KITS 2.10
Cross Reference Guide

A296 235A4753BK1 $550 G4-7KITS 3.35 A764 249A4321AMG04 $561 G4-7KITS 3.33
A297 235A4753BK2 $550 G4-7KITS 3.35 A765 249A4321AMG05 $590 G4-7KITS 2.10
A298 235A4753BK3 $550 G4-7KITS 3.35 A765 249A4321AMG05 $590 G4-7KITS 3.33
A300 249A4234ABG02 $158 G6-7KITS 1.22 A766 249A4321AMG06 $590 G4-7KITS 2.10
A300 249A4234ABG02 $158 G6-7KITS 2.11 A766 249A4321AMG06 $590 G4-7KITS 3.33
A301 249A4234ABG03 $158 G6-7KITS 1.22 A767 249A4321AMG07 $1,408 G4-7KITS 2.10
A301 249A4234ABG03 $158 G6-7KITS 2.11 A767 249A4321AMG07 $1,408 G4-7KITS 3.33
A320 227B1056AA-G01 6.16 A768 249A4321AMG08 $1,408 G4-7KITS 2.10
A321 227B1058AA-G02 6.16 A768 249A4321AMG08 $1,408 G4-7KITS 3.33
A322 227B1058AA-G01 6.16 A826 235A4575GE001 $109 G4-7KITS 3.34
A323 227B1056AB-G01 6.16 A826 235A4575GE001 $109 G4-7KITS 4.6
A324 227B1056AC-G01 6.16 A828 235A4575GE003 $140 G4-7KITS 3.34
A325 227B1056AD-G01 6.16 A828 235A4575GE003 $140 G4-7KITS 4.6
A326 227B1056AD-G02 6.16 A830 235A4575GE005 $459 G4-7KITS 3.34
A327 227B1056AD-G03 6.16 A830 235A4575GE005 $459 G4-7KITS 4.6
A337 153B1004ACG120 $89 G4-7KITS 1.22 A832 235A4575GE007 $549 G4-7KITS 3.34
A337 153B1004ACG120 $89 G4-7KITS 2.11 A832 235A4575GE007 $549 G4-7KITS 4.6
A337 153B1004ACG120 $89 G4-7KITS 3.36 A927 249A4321AGG01 $360 G6-7KITS 5.2
A340 4001A5921CYG006 $68 G4-7KITS 3.34 A991 249A4321ARG01 $608 G4-7KITS 3.33
A341 4001A5921CYG001 $68 G4-7KITS 3.34 A992 249A4321ARG02 $608 G4-7KITS 3.33
A342 4001A5921CYG002 $68 G4-7KITS 3.34 A993 249A4321ARG03 $1,028 G4-7KITS 3.33
A343 249A4234AAG20 $68 G4-7KITS 3.34 A994 249A4321ARG04 $1,028 G4-7KITS 3.33
A344 249A4234AAG03 $68 G4-7KITS 3.34 A995 249A4321ARG05 $1,400 G4-7KITS 3.33
A345 249A4234AAG21 $68 G4-7KITS 3.34 A996 249A4321ARG06 $1,400 G4-7KITS 3.33
A346 249A4234AAG07 $68 G4-7KITS 3.34 A997 249A4321ARG07 $1,457 G4-7KITS 3.33
A542 235A4985ARG01 $1,027 G4-7KITS 4.6 A998 249A4321ARG08 $1,679 G4-7KITS 3.33
A543 235A4985APG01 $1,027 G4-7KITS 4.6 A1001 4002B5914ANP001 $145 G4-7KITS 3.34
A544 235A4985ANG01 $1,842 G4-7KITS 4.6 A1001 4002B5914ANP001 $145 G4-7KITS 4.6
A545 235A4985ANG01 $1,842 G4-7KITS 4.6 A1002 4002B5914ANP002 $145 G4-7KITS 3.34
A565 893A690AAG01 $370 GO-2SK3 7.23 A1002 4002B5914ANP002 $145 G4-7KITS 4.6
A569 893A666AAG02 $973 GO-2SK3 7.23 A1003 4002B5914ANP003 $158 G4-7KITS 3.34
A641 36A167700AAG01 $1,097 GO-2KITS 7.24 A1003 4002B5914ANP003 $158 G4-7KITS 4.6
A642 36A167700BAG01 $978 GO-2KITS 7.24 A1004 4002B5914ANP004 $190 G4-7KITS 3.34
A643 36A167700CAG01 $1,008 GO-2KITS 7.24 A1004 4002B5914ANP004 $190 G4-7KITS 4.6
A644 36A167701AAG01 $1,204 GO-2KITS 7.24 A1005 4002B5914ANP005 $246 G4-7KITS 3.34
A645 36A167701BAG01 $1,303 GO-2KITS 7.24 A1005 4002B5914ANP005 $246 G4-7KITS 4.6
A646 36A167701CAG01 $1,303 GO-2KITS 7.24 A1007 235A4575GS1 $336 G4-7KITS 3.34
A647 36A167702AAG01 $2,382 GO-2KITS 7.24 A1021 249A9514AAG01 $441 G4-7KITS 1.21
A648 36A167702BAG01 $1,392 GO-2KITS 7.24 A1022 249A9514AAG02 $441 G4-7KITS 1.21
A649 36A167702CAG01 $2,604 GO-2KITS 7.24 A1023 249A9514AAG03 $450 G4-7KITS 1.21
A650 36A167702DAG01 $2,604 GO-2KITS 7.24 A1024 249A9514AAG04 $450 G4-7KITS 1.21
A670 36A172471AAG02 $189 GO-2KITS 7.23 A1025 249A9514AAG05 $483 G4-7KITS 1.21
A671 36A172472AAG01 $425 GO-2KITS 7.23 A1026 249A9514AAG06 $483 G4-7KITS 1.21
A672 36A172473AAG01 $492 GO-2KITS 7.23 A1027 249A9514AAG07 $595 G4-7KITS 1.21
A674 36A172474AAG01 $730 GO-2KITS 7.23 A1028 249A9514AAG08 $595 G4-7KITS 1.21
A676 36A172475AAG01 $621 GO-2KITS 7.23 A1050 249A9573AAG01 $258 G4-7KITS 1.20
A677 36A167802BAG02 $202 GO-2KITS 7.24 A1050 249A9573AAG01 $258 G4-7KITS 2.10
A678 36A167803BAG02 $219 GO-2KITS 7.24 A1051 249A9573AAG02 $418 G4-7KITS 1.20
A680 36A167804BAG02 $269 GO-2KITS 7.24 A1051 249A9573AAG02 $418 G4-7KITS 2.10
A682 36A167805BAG02 $336 GO-2KITS 7.24 A1052 249A9573AAG03 $539 G4-7KITS 1.20
A683 36A167806BAG02 $353 GO-2KITS 7.24 A1052 249A9573AAG03 $539 G4-7KITS 2.10
A684 36A167806BAG01 $353 GO-2KITS 7.24 A1053 249A9573AAG04 $539 G4-7KITS 1.20
A685 36A167809BAG01 $386 GO-2KITS 7.24 A1053 249A9573AAG04 $539 G4-7KITS 2.10
A686 36A167701CAG14 $1,260 GO-2KITS 7.24 A1054 249A9573AAG05 $725 G4-7KITS 1.20
A687 36A167741CBG01 $1,337 GO-2KITS 7.23 A1054 249A9573AAG05 $725 G4-7KITS 2.10
A688 36A167742ABG02 $1,342 GO-2KITS 7.23 A1055 249A9573AAG06 $857 G4-7KITS 1.20
A689 36A167743CBG02 $1,250 GO-2KITS 7.23 A1055 249A9573AAG06 $857 G4-7KITS 2.10
A690 36A167744ABG03 $1,530 GO-2KITS 7.23 A1056 249A9573AAG07 $857 G4-7KITS 1.20
A691 36A167745GBG10 $1,805 GO-2KITS 7.23 A1056 249A9573AAG07 $857 G4-7KITS 2.10
A692 36A167746GBG10 $1,504 GO-2KITS 7.23 A1057 249A9573AAG08 $857 G4-7KITS 1.20
A693 36A167747GBG10 $1,517 GO-2KITS 7.23 A1057 249A9573AAG08 $857 G4-7KITS 2.10
A694 36A167747GDG10 $1,815 GO-2KITS 7.23 A1058 249A9573AAG09 $82 G4-7KITS 1.20
A695 36A167749EBG34 $3,024 GO-2KITS 7.23 A1058 249A9573AAG09 $82 G4-7KITS 2.10
A735 249A4321ABG15 $261 G6-7KITS 4.6 A1059 249A9573AAG10 $112 G4-7KITS 1.20
A736 249A4321ABG16 $439 G6-7KITS 4.6 A1059 249A9573AAG10 $112 G4-7KITS 2.10
A737 249A4321ABG17 $575 G6-7KITS 4.6 A1060 249A9573AAG11 $138 G4-7KITS 1.20
A739 249A4321ABG19 $575 G6-7KITS 4.6 A1060 249A9573AAG11 $138 G4-7KITS 2.10
A761 249A4321AMG01 $261 G4-7KITS 3.33 A1061 249A9573AAG12 $160 G4-7KITS 1.20
A762 249A4321AMG02 $261 G4-7KITS 3.33 A1061 249A9573AAG12 $160 G4-7KITS 2.10
A763 249A4321AMG03 $561 G4-7KITS 2.10 A1062 249A9573AAG13 $835 G4-7KITS 1.20

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.3
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
A1062 249A9573AAG13 $835 G4-7KITS 2.10 D167 5BCD56ED307 29 $1,628 GO-1DC 7.6
A1063 249A9573AAG14 $835 G4-7KITS 1.20 D169 5BCD56ND91 42 $1,853 GO-1DC 7.6

Cross Reference Guide

A1063 249A9573AAG14 $835 G4-7KITS 2.10 D246 5PY59EY4 5 $818 GO-7PTC 7.8
A1064 249A9573ABG01 $98 G4-7KITS 1.21 D250 5PY59JY85 8 $1,635 GO-7PTC 7.8
A1064 249A9573ABG01 $98 G4-7KITS 2.10 D251 5PY59JY84 7 $1,635 GO-7PTC 7.8
A1065 249A9573ABG02 $134 G4-7KITS 1.21 D252 5PY59JY3 7 $1,602 GO-7PTC 7.8
A1065 249A9573ABG02 $134 G4-7KITS 2.10 D255 5BC42AE1003 32 $2,182 GO-7PTC 7.9
A1066 249A9573ABG03 $167 G4-7KITS 1.21 D256 5BC42AE1002 32 $2,182 GO-7PTC 7.9
A1066 249A9573ABG03 $167 G4-7KITS 2.10 D267 5BC42AE1008 38 $2,195 GO-7PTC 7.9
A1067 249A9573ABG04 $224 G4-7KITS 1.21 D268 5BC42AE1001 38 $2,195 GO-7PTC 7.9
A1067 249A9573ABG04 $224 G4-7KITS 2.10 D273 5BPA56HAG11 19 $271 GO-1PM 7.6
A1068 249A9573ABG05 $297 G4-7KITS 1.21 D274 5BPA56KAG19 25 $376 GO-1PM 7.6
A1068 249A9573ABG05 $297 G4-7KITS 2.10 D275 5BPA56KAG20 29 $336 GO-1PM 7.6
A1069 249A9573ABG06 $441 G4-7KITS 1.21 D276 5BPA56KAG21 29 $379 GO-1PM 7.6
A1069 249A9573ABG06 $441 G4-7KITS 2.10 D277 5BPA56NAG9 39 $430 GO-1PM 7.6
A1071 249A9500ABPT7 $418 G4-7KITS 1.20 D278 5BPA56NAG10 43 $494 GO-1PM 7.6
A1072 249A9500ABPT8 $418 G4-7KITS 1.20 D279 5BPA56RAG8 41 $624 GO-1PM 7.6
A1073 249A9500ABPT9 $539 G4-7KITS 1.20 D280 5BPA56RAG9 41 $624 GO-1PM 7.6
A1074 249A9500ABPT10 $539 G4-7KITS 1.20 D283 5BPA56HAG8 19 $281 GO-1PM 7.6
A1075 249A9500ABPT11 $785 G4-7KITS 1.20 D284 5BPA56KAG8 25 $331 GO-1PM 7.6
A1076 249A9500ABPT12 $785 G4-7KITS 1.20 D285 5BPA56KAG9 29 $331 GO-1PM 7.6
A1077 249A9500ABPT13 $857 G4-7KITS 1.20 D286 5BPA56KAG10 29 $321 GO-1PM 7.6
A1078 249A9500ABPT14 $857 G4-7KITS 1.20 D287 5BPA56NAG6 37 $332 GO-1PM 7.6
A1079 249A9500ABPT15 $993 G4-7KITS 1.20 D288 5BPA56NAG7 37 $345 GO-1PM 7.6
A1080 249A9500ABPT16 $993 G4-7KITS 1.20 D289 5BPA56RAG4 40 $442 GO-1PM 7.6
A1201 249A4267AD-G01 $105 G4-7KITS 3.30 D290 5BPA56RAG5 40 $442 GO-1PM 7.6
A1201 249A4267AD-G01 $105 G4-7KITS 3.34 D294 5BC58JBS6259 38 $475 GO-1GLF 8.6
A1202 249A4267AD-G02 $110 G4-7KITS 3.30 D295 5BC48JB1059 43 $510 GO-1GLF 8.6
A1202 249A4267AD-G02 $110 G4-7KITS 3.34 D296 5BC59JBS6258 41 $510 GO-1GLF 8.6
A1203 249A4267AD-G03 $125 G4-7KITS 3.30 D297 5BC48JB1061 50 $718 GO-1GLF 8.6
A1203 249A4267AD-G03 $125 G4-7KITS 3.34 D298 5BC48JB1062 43 $718 GO-1GLF 8.6
A1204 249A4267AD-G04 $136 G4-7KITS 3.30 D300 5CD122NE001 55 $1,038 GO-2SK3 7.6
A1204 249A4267AD-G04 $136 G4-7KITS 3.34 D301 5CD122HE001 55 $1,062 GO-2SK3 7.6
A1205 249A4267AD-G05 $155 G4-7KITS 3.30 D302 5CD123GE001 67 $1,242 GO-2SK3 7.6
A1205 249A4267AD-G05 $155 G4-7KITS 3.34 D303 5CD123UE001 59 $1,255 GO-2SK3 7.6
A1206 249A4267AD-G06 $173 G4-7KITS 3.30 D304 5CD123PE001 67 $1,277 GO-2SK3 7.6
A1206 249A4267AD-G06 $173 G4-7KITS 3.34 D305 5CD125TE001 93 $1,619 GO-2SK3 7.6
D106 5BCC56CD10 25 $1,388 GO-1DC 7.11 D306 5CD123UE002 67 $1,505 GO-2SK3 7.6
D107 5BCC56ED8 28 $1,493 GO-1DC 7.11 D307 5CD124TE001 77 $1,529 GO-2SK3 7.6
D109 5BCJ56CD9 26 $1,568 GO-1DC 7.11 D308 5CD125TE002 102 $1,938 GO-2SK3 7.6
D110 5BCJ56ED7 31 $1,845 GO-1DC 7.11 D309 5CD125YE001 102 $1,938 GO-2SK3 7.6
D111 5BCC56BD34 23 $1,298 GO-1DC 7.11 D310 5CD125WE001 102 $1,962 GO-2SK3 7.6
D112 5BCC56KD6 37 $1,673 GO-1DC 7.11 D311 5CD122NP001 67 $1,439 GO-2PK3 7.6
D113 5BCJ56BD34 23 $1,418 GO-1DC 7.11 D313 5CD123GP001 77 $1,448 GO-2PK3 7.6
D115 5BCD56CD247 24 $1,560 GO-1DC 7.6 D314 5CD123UP001 59 $1,448 GO-2PK3 7.6
D116 5BCD56ND88 41 $1,619 GO-1DC 7.6 D315 5CD123PP001 79 $1,208 GO-2PK3 7.6
D117 5BCD56RD397 52 $1,919 GO-1DC 7.6 D316 5CD125TP001 113 $1,802 GO-2PK3 7.6
D118 5BCD56RD398 55 $1,838 GO-1DC 7.6 D317 5CD123UP002 78 $1,448 GO-2PK3 7.6
D120 5PY59EY2 5 $681 GO-7PTC 7.8 D318 5CD124TP001 88 $1,401 GO-2PK3 7.6
D121 5PY59EY3 4 $681 GO-7PTC 7.8 D319 5CD125TP002 113 $1,956 GO-2PK3 7.6
D122 5PY59JY1 8 $1,335 GO-7PTC 7.8 D320 5CD125YP001 113 $1,956 GO-2PK3 7.6
D123 5PY59JY2 7 $1,335 GO-7PTC 7.8 D321 5CD125WP001 115 $1,913 GO-2PK3 7.6
D124 5PY59JY23 7 $1,335 GO-7PTC 7.8 D350 5BPA56HAG9 19 $354 GO-1PM 8.7
D125 5PY59JY24 7 $1,335 GO-7PTC 7.8 D351 5BPA56HAG10 19 $354 GO-1PM 8.7
D126 5BC42AB1729 26 $1,901 GO-7PTC 7.9 D352 5BPA56KAG15 25 $372 GO-1PM 8.7
D127 5BC46AB1570 36 $2,994 GO-7PTC 7.9 D353 5BPA56KAG16 25 $372 GO-1PM 8.7
D128 5BC46AB1571 36 $2,994 GO-7PTC 7.9 D354 5BPA56KAG17 29 $420 GO-1PM 8.7
D130 5BC46AB1590 39 $3,013 GO-7PTC 7.9 D355 5BPA56KAG18 29 $420 GO-1PM 8.7
D131 5BC46AB1591 39 $3,013 GO-7PTC 7.9 D356 5BPA56NAG11 42 $511 GO-1PM 8.7
D132 5BC46AB2014 41 $3,103 GO-7PTC 7.9 D357 5BPA56NAG12 39 $511 GO-1PM 8.7
D133 5BC46AB2082 41 $3,103 GO-7PTC 7.9 D358 5BPA56RAG10 41 $634 GO-1PM 8.7
D135 5BCD56RD418 55 $2,085 GO-1DC 7.6 D359 5BPA56RAG11 41 $634 GO-1PM 8.7
D136 5BC42AB1834 25 $1,901 GO-7PTC 7.9 D360 5BPA56HAG24 19 $316 GO-1PM 7.10
D137 5BC42AB1830 26 $1,901 GO-7PTC 7.9 D361 5BPA56KAG42 25 $338 GO-1PM 7.10
D138 5BC46AB1572 29 $2,994 GO-7PTC 7.9 D362 5BPA56KAG43 25 $325 GO-1PM 7.10
D139 5BC46AB1581 36 $3,026 GO-7PTC 7.9 D363 5BPA56KBF10 29 $356 GO-1PM 7.10
D140 5BC46AB1582 36 $3,026 GO-7PTC 7.9 D364 5BPA56KBF11 29 $343 GO-1PM 7.10
D141 5BC42AB1780 29 $1,923 GO-7PTC 7.9 D365 5BPA56PBF25 36 $461 GO-1PM 7.10
D142 5BC42AB1882 29 $1,923 GO-7PTC 7.9 D366 5BPA56NBF27 36 $433 GO-1PM 7.10
D143 5BC42AB2177 30 $1,983 GO-7PTC 7.9 D367 5BPA56PBF26 41 $599 GO-1PM 7.10
D144 5BC46AB2291 41 $3,103 GO-7PTC 7.9 D375 5BC58JBS6337 38 $465 GO-1GLF 8.6
D149 5BC42AB2195 30 $1,983 GO-7PTC 7.9 D376 5BC58JBS6338 50 $465 GO-1GLF 8.6

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.4 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
D377 5BC58JBS6334 38 $511 GO-1GLF 8.6 D455 5CD193PA065A129 860 $12,169 GO-2AS 7.2
D378 5BC58JBS6335 38 $511 GO-1GLF 8.6 D456 5CD193PA065A140 860 $12,169 GO-2AS 7.2
Cross Reference Guide

D379 5BC49JB1115 50 $738 GO-1GLF 8.6 D457 5CD193PA084A037 940 $9,844 GO-2AS 7.5
D380 5BC49JB3071 60 $919 GO-1GLF 8.6 D460 5CD193TA027A007 940 $9,844 GO-2AS 7.5
D381 5BC58JBS6339 38 $465 GO-1GLF 8.6 D462 5CD194NA067A051 1020 $13,872 GO-2AS 7.2
D382 5BC58JBS6342 40 $511 GO-1GLF 8.6 D463 5CD194RA060A028 1100 $12,421 GO-2AS 7.5
D383 5BC58JBS6340 35 $579 GO-1GLF 8.6 D465 5CD194SA081A067 1020 $15,266 GO-2AS 7.2
D384 5BC49JB2048 60 $987 GO-1GLF 8.6 D466 5CD194SA081A129 1020 $15,266 GO-2AS 7.2
D385 5BC49JB2049 62 $964 GO-1GLF 8.6 D467 5CD194SA082A418 1085 $15,471 GO-2AS 7.4
D386 5BC58JBS6341 28 $579 GO-1GLF 8.6 D468 5CD194SA082A315 1085 $18,029 GO-2AS 7.4
D387 5BC58JBS6344 40 $590 GO-1GLF 8.6 D469 5CD194UA035A008 1100 $12,421 GO-2AS 7.5
D388 5BC49JB1155 55 $840 GO-1GLF 8.6 D471 5CD203PA088A032 1300 $18,079 GO-2AS 7.2
D390 BC58JBS6381 35 $680 GO-1GLF 8.6 D473 5CD203PA097A176 1365 $20,513 GO-2AS 7.4
D391 BC58JBS6384 35 $680 GO-1GLF 8.6 D474 5CD204PA086A041 1680 $18,104 GO-2AS 7.5
D392 BC48JB3080 49 $780 GO-1GLF 8.6 D476 5CD204RA068A048 1600 $21,751 GO-2AS 7.2
D394 BC49JB1132 55 $880 GO-1GLF 8.6 D477 5CD204RA068A049 1600 $21,751 GO-2AS 7.2
D395 BC49JB1134 55 $880 GO-1GLF 8.6 D478 5CD204SA038A261 1720 $25,863 GO-2AS 7.4
D396 BC49JB1144 53 $800 GO-1GLF 8.6 D480 5CD222PA076B030 1900 $27,588 GO-2AS 7.2
D397 BC49JB1149 54 $800 GO-1GLF 8.6 D482 5CD222YA001B098 1982 $31,371 GO-2AS 7.4
D398 BC48JB3084 45 $760 GO-1GLF 8.6 D486 5CD223SA074B132 2290 $40,675 GO-2DS 7.2
D400 5CD142FC008B054 80 $2,649 GO-2AS 7.7 D489 5CD224TA033B079 2810 $49,160 GO-2DS 7.3
D401 5CD142FE012B025 80 $2,649 GO-2AS 7.7 D490 5CD226SA002B052 4343 $48,107 GO-2DS 7.4
D402 5CD142GE011B020 80 $2,684 GO-2AS 7.7 D492 5CD226TA001B048 4343 $60,809 GO-2DS 7.4
D403 5CD143JA014B026 105 $2,124 GO-2AS 7.2 D530 5CD144MA020B073 128 $2,809 GO-2AS 7.5
D404 5CD143JC014B012 102 $2,210 GO-2AS 7.2 D536 5CD142GE011B039 80 $2,795 GO-2AS 7.7
D405 5CD143LE007B021 102 $2,784 GO-2AS 7.7 D537 5CD143MC003B040 102 $2,906 GO-2AS 7.7
D406 5CD143ME003B021 102 $2,906 GO-2AS 7.7 D539 5CD143MC003B018 102 $2,824 GO-2AS 7.7
D407 5CD144FA002B020 128 $2,612 GO-2AS 7.2 D540 5CD143LC007B034 102 $2,784 GO-2AS 7.7
D408 5CD145SA011B018 165 $3,709 GO-2AS 7.5 D541 5CD184TA094B071 769 $7,922 GO-2AS 7.2
D409 5CD144PA002B055 128 $2,612 GO-2AS 7.2 D542 5CD184TA094B075 769 $7,922 GO-2AS 7.2
D410 5CD144PC016B013 128 $2,698 GO-2AS 7.2 D543 5CD194NA067A052 1020 $12,140 GO-2AS 7.2
D411 5CD144SC003B063 128 $2,857 GO-2AS 7.7 D544 5CD193PA065A160 860 $10,358 GO-2AS 7.2
D412 5CD144SE005B028 128 $2,857 GO-2AS 7.7 D547 5CD223SA074B133 2290 $33,922 GO-2AS 7.2
D413 5CD144UC005B037 128 $2,921 GO-2AS 7.7 D548 5CD183SA043B052 691 $7,216 GO-2AS 7.3
D414 5CD144UC023B030 128 $4,058 GO-2AS 7.7 D553 5CD144MA020B038 128 $2,193 GO-2AS 7.5
D415 5CD145GA002B016 165 $3,709 GO-2AS 7.5 D554 5CD204PA086A042 1680 $14,951 GO-2AS 7.5
D417 5CD145UA005B026 162 $3,152 GO-2AS 7.2 D555 5CD145VE005B008 160 $2,994 GO-2AS 7.7
D418 5CD145UA030B005 172 $4,289 GO-2AS 7.4 D558 5CD194SA082A247 1020 $13,892 GO-2AS 7.3
D419 5CD145VC005B055 160 $2,994 GO-2AS 7.7 D559 5CD194SA082A419 1020 $16,450 GO-2AS 7.3
D420 5CD145WC006B021 160 $3,795 GO-2AS 7.7 D560 5CD203PA097A225 1300 $18,934 GO-2AS 7.3
D421 5CD152GA017B014 234 $3,152 GO-2AS 7.2 D561 5CD153JA001B090 272 $4,729 GO-2AS 7.4
D422 5CD152NC025B015 243 $3,403 GO-2AS 7.2 D562 5CD163KA009A136 381 $5,458 GO-2AS 7.4
D423 5CD153JA001B023 252 $3,592 GO-2AS 7.2 D563 5CD164MA012A076 423 $6,092 GO-2AS 7.4
D424 5CD153JA001B106 252 $3,592 GO-2AS 7.3 D564 5CD173NA010A130 513 $6,864 GO-2AS 7.4
D425 5CD153RA039B003 252 $3,592 GO-2AS 7.2 D565 5CD174RA009A141 576 $7,424 GO-2AS 7.4
D426 5CD153RA039B039 252 $3,592 GO-2AS 7.3 D566 5CD183SA043B017 752 $8,649 GO-2AS 7.4
D427 5CD153RC027B015 252 $3,843 GO-2AS 7.2 D567 5CD184TA094B076 830 $9,673 GO-2AS 7.4
D428 5CD153TC024B001 261 $4,696 GO-2AS 7.7 D568 5CD174VA019A060 587 $6,611 GO-2AS 7.5
D429 5CD154KA026B004 287 $4,487 GO-2AS 7.5 D569 5CD174NA005A080 587 $6,611 GO-2AS 7.5
D430 5CD154TA007B005 287 $4,487 GO-2AS 7.5 D570 5CD183WA043B006 732 $7,594 GO-2AS 7.5
D431 5CD154ZC852B800 289 $5,497 GO-2AS 7.7 D572 5CD184YA064B004 812 $8,893 GO-2AS 7.5
D432 5CD163KA009A133 361 $4,321 GO-2AS 7.2 D574 5CD204SA038A265 1650 $24,010 GO-2AS 7.3
D433 5CD163KA009A134 361 $4,321 GO-2AS 7.3 D575 5CD222YA001B125 1900 $29,518 GO-2AS 7.3
D434 5CD163SA026A070 361 $4,321 GO-2AS 7.2 D576 5CD185VA811B802 769 $9,430 GO-2AS 7.3
D435 5CD163SC035A010 378 $4,572 GO-2AS 7.2 D577 5CD185VA012B003 888 $11,077 GO-2AS 7.3
D436 5CD164LA014A031 442 $5,123 GO-2AS 7.5 D578 5CD185VA811B803 830 $10,863 GO-2AS 7.4
D437 5CD164MA012A136 403 $4,955 GO-2AS 7.2 D579 5CD185VA012B001 949 $12,510 GO-2AS 7.4
D438 5CD164MA012A137 403 $4,955 GO-2AS 7.3 D583 5CD145WA009B020 162 $3,709 GO-2AS 7.7
D439 5CD164MA038A028 403 $4,955 GO-2AS 7.3 D584 5CD154ZC801B803 389 $5,831 GO-2AS 7.7
D440 5CD164TA009A034 442 $5,123 GO-2AS 7.5 D585 5CD142GA010B034 83 $2,598 GO-2AS 7.7
D441 5CD164UA023A109 403 $4,955 GO-2AS 7.2 D586 5CD143UA022B010 105 $2,631 GO-2AS 7.7
D442 5CD173NA010A114 493 $6,118 GO-2AS 7.2 D587 5CD142EA019B017 83 $1,804 GO-2AS 7.2
D444 5CD173VA018A079 493 $6,118 GO-2AS 7.2 D588 5CD143BA012B038 105 $2,124 GO-2AS 7.2
D445 5CD174RA009A197 548 $6,734 GO-2AS 7.2 D589 5CD184VA085B006 769 $7,950 GO-2AS 7.2
D446 5CD174RA009A257 548 $6,136 GO-2AS 7.3 D590 5CD203LA057A013 1300 $16,900 GO-2AS 7.2
D448 5CD174WA020A089 548 $6,734 GO-2AS 7.2 D592 5CD203PA108A034 1300 $20,183 GO-2AS 7.3
D449 5CD184TA094B068 769 $9,049 GO-2AS 7.2 D593 5CD204SA046A025 1650 $25,259 GO-2AS 7.3
D450 5CD184TA094B070 769 $9,049 GO-2AS 7.2 D594 5CD222YA006B022 1900 $30,767 GO-2AS 7.3
D451 5CD184TA094B069 769 $8,240 GO-2AS 7.3 D600 5CD604KA002C008 5743 $76,964 GO-2DS 7.4
D453 5CD193MA038A053 860 $10,542 GO-2AS 7.2 D601 5CD604LA001C015 6043 $99,367 GO-2DS 7.4

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.5
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
D609 5CD184PA021B018 769 $9,187 GO-2AS 7.3 E7012 5KS215ATE305 157 $643 G4-7D$Z1 2.2
D610 5CD185SA001B012 888 $10,577 GO-2AS 7.3 E7013 5KS254ATE305 260 $838 G4-7D$Z1 2.2

Cross Reference Guide

D611 5CD194SA109A051 1020 $16,514 GO-2AS 7.3 E7014 5KS256ATE305 310 $981 G4-7D$Z1 2.2
D612 5CD194SA109A072 1020 $16,514 GO-2AS 7.3 E7015 5KS284ATE305 394 $1,263 G4-7D$Z1 2.2
D613 5CD223MA051B038 290 $23,807 GO-2AS 7.3 E7017 5KS286ATE305 436 $1,549 G4-7D$Z1 2.2
D614 5CD203PA108A033 1300 $20,183 GO-2AS 7.3 E7019 5KS324ATE305 580 $1,838 G4-7D$Z1 2.2
D615 5CD223NA048B024 2290 $26,933 GO-2AS 7.3 E7022 5KS326ATE305 639 $2,103 G4-7D$Z1 2.3
D616 5CD204SA046A024 1650 $25,259 GO-2AS 7.3 E7024 5KS364ATE308 770 $3,091 G4-7D$Z1 2.3
D617 5CD222YA006B023 1900 $30,767 GO-2AS 7.3 E7026 5KS365ATE308 838 $3,610 G4-7D$Z1 2.3
D618 5CD223PA097B025 2290 $34,750 GO-2AS 7.3 E7029 5KS404ATE308 1090 $4,467 G4-7D$Z1 2.3
D619 5CD224RA090B076 2810 $40,757 GO-2DS 7.3 E7032 5KS405ATE308 1150 $5,316 G4-7D$Z1 2.3
D620 5CD226AA002B024 4260 $65,720 GO-2DS 7.3 E7034 5KS444ATE308 1494 $6,733 G4-7D$Z1 2.3
D650 5CD183MA033B020 752 $7,397 GO-2AS 7.4 E7036 5KS445ATE308 1715 $8,268 G4-7D$Z1 2.3
D651 5CD184NA054B019 830 $8,440 GO-2AS 7.4 E7254 5KS326ATE215 639 $2,066 G4-7D$Z1 2.3
D652 5CD192NA027A136 815 $12,510 GO-2AS 7.4 E7257 5KS404ATE215 1090 $4,167 G4-7D$Z1 2.3
D654 5CD194XA002A073 1085 $13,516 GO-2AS 7.4 E7259 5KS444ATE218 1494 $7,209 G4-7D$Z1 2.3
D655 5CD185VA012B002 949 $12,510 GO-2AS 7.4 E7272 5KS447ATE208 2100 $12,600 G4-7D$Z1 2.3
D656 5CD193PA094A243 925 $15,471 GO-2AS 7.4 E7273 5KS449ATE208 2150 $15,541 G4-7D$Z1 2.3
D657 5CD193PA094A244 925 $15,471 GO-2AS 7.4 E7310 5KS324ATE204 580 $1,772 G4-7D$Z1 2.3
D658 5CD194XA002A092 1085 $15,782 GO-2AS 7.4 E7320 5KS326ATE204 639 $2,066 G4-7D$Z1 2.3
D659 5CD203NA039A054 1365 $18,933 GO-2AS 7.4 E7330 5KS364ATE204 770 $2,684 G4-7D$Z1 2.3
D660 5CD204NA044A093 1665 $21,917 GO-2AS 7.4 E7340 5KS404ATE204 1090 $4,167 G4-7D$Z1 2.3
D661 5CD204PA107A104 1665 $21,917 GO-2AS 7.4 E7342 5KS405ATE218 1150 $4,992 G4-7D$Z1 2.3
D662 5CD204PA107A141 1665 $25,236 GO-2AS 7.4 E7360 5KS445ATE218 1715 $10,150 G4-7D$Z1 2.3
D663 5CD204SA038A260 1720 $25,863 GO-2AS 7.4 E7370 5KS447ATE218 2100 $12,600 G4-7D$Z1 2.3
D664 5CD222YA001B096 1982 $31,371 GO-2AS 7.4 E7381 5KS364ATE205 770 $2,684 G4-7D$Z1 2.3
D680 5CD142AA036B008 83 $2,221 GO-2AS 7.5 E7383 5KS364ATE215 770 $2,684 G4-7D$Z1 2.3
D681 5CD142DA036B024 83 $2,073 GO-2AS 7.5 E7391 5KS365ATE205 838 $3,269 G4-7D$Z1 2.3
D682 5CD144EC002B052 128 $3,282 GO-2AS 7.5 E7393 5KS365ATE215 838 $3,269 G4-7D$Z1 2.3
D683 5CD154SA016B023 280 $4,487 GO-2AS 7.5 E7401 5KS404ATE205 1090 $4,167 G4-7D$Z1 2.3
D684 5CD154SA045B001 280 $4,487 GO-2AS 7.5 E7501 5KS404ATE118 1092 $5,774 G4-7D$Z1 2.3
D685 5CD154JA015B024 280 $4,487 GO-2AS 7.5 E7502 5KS405ATE118 1194 $7,024 G4-7D$Z1 2.3
D686 5CD164LA041A026 403 $5,446 GO-2AS 7.5 E7503 5KS444ATE118 1590 $12,368 G4-7D$Z1 2.3
E707 5KS143ATE205 46 $222 G4-7D$Z1 2.2 E7504 5KS445ATE118 1800 $14,387 G4-7D$Z1 2.3
E708 5KS145ATE305 58 $285 G4-7D$Z1 2.2 E7635 5KS182ATE204 72 $277 G4-7D$Z1 2.2
E709 5KS143ATE105 46 $242 G4-7D$Z1 2.2 E7640 5KS213ATE204 157 $538 G4-7D$Z1 2.2
E710 5KS145ATE202 56 $242 G4-7D$Z1 2.2 E7643 5KS215ATE204 157 $650 G4-7D$Z1 2.2
E717 5KS145ATE102 58 $285 G4-7D$Z1 2.2 E7646 5KS254ATE204 260 $864 G4-7D$Z1 2.2
E718 5KS145ATE205 58 $267 G4-7D$Z1 2.2 E7649 5KS256ATE204 310 $1,055 G4-7D$Z1 2.2
E719 5KS145ATE105 60 $320 G4-7D$Z1 2.2 E7652 5KS284ATE204 394 $1,226 G4-7D$Z1 2.2
E720 5KS182ATE205 72 $277 G4-7D$Z1 2.2 E7654 5KS286ATE204 436 $1,425 G4-7D$Z1 2.3
E721 5KS182ATE105 72 $389 G4-7D$Z1 2.2 E7707 5KS182ATE305 72 $313 G4-7D$Z1 2.2
E722 5KS184ATE205 91 $389 G4-7D$Z1 2.2 E7710 5KS184ATE305 91 $402 G4-7D$Z1 2.2
E723 5KS184ATE105 91 $560 G4-7D$Z1 2.2 E7714 5KS182ATE206 72 $277 G4-7D$Z1 2.2
E730 5KS213ATE205 128 $538 G4-7D$Z1 2.2 E7716 5KS184ATE206 91 $389 G4-7D$Z1 2.2
E731 5KS215ATE205 157 $650 G4-7D$Z1 2.2 E7729 5KS213ATE206 128 $538 G4-7D$Z1 2.2
E732 5KS254ATE205 260 $864 G4-7D$Z1 2.2 E7734 5KS215ATE206 157 $650 G4-7D$Z1 2.2
E733 5KS256ATE205 310 $1,055 G4-7D$Z1 2.2 E7744 5KS254ATE206 260 $864 G4-7D$Z1 2.2
E734 5KS284ATE205 394 $1,226 G4-7D$Z1 2.2 E7754 5KS256ATE206 310 $1,055 G4-7D$Z1 2.2
E735 5KS286ATE205 436 $1,425 G4-7D$Z1 2.3 E7757 5KS284ATE206 394 $1,226 G4-7D$Z1 2.2
E736 5KS324ATE205 480 $1,772 G4-7D$Z1 2.3 E7763 5KS286ATE206 436 $1,425 G4-7D$Z1 2.3
E737 5KS326ATE205 639 $2,066 G4-7D$Z1 2.3 E7808 5KS184ATE204 91 $389 G4-7D$Z1 2.2
E741 5KS405ATE208 1150 $4,992 G4-7D$Z1 2.3 E7825 5KS365ATE204 838 $3,269 G4-7D$Z1 2.3
E742 5KS444ATE208 1494 $7,209 G4-7D$Z1 2.3 E7962 5KS447ATE308 2100 $9,166 G4-7D$Z1 2.3
E743 5KS445ATE208 1715 $10,150 G4-7D$Z1 2.3 E7963 5KS449ATE308 2150 $14,829 G4-7D$Z1 2.3
E750 5KS213ATE105 163 $665 G4-7D$Z1 2.2 E9119 5KS324SS308D16 710 $3,096 G6-7S$ 8.13
E751 5KS215ATE105 157 $842 G4-7D$Z1 2.2 E9122 5KS326SS308D15 730 $3,566 G6-7S$ 8.13
E752 5KS254ATE105 260 $993 G4-7D$Z1 2.2 E9124 5KS364SS308D15 1070 $4,833 G6-7S$ 8.13
E753 5KS256ATE105 310 $1,212 G4-7D$Z1 2.2 E9126 5KS365SS308D14 1050 $5,549 G6-7S$ 8.13
E754 5KS284ATE115 420 $1,446 G4-7D$Z1 2.3 E9127 5KS365SS318D8 1050 $5,549 G6-7S$ 8.13
E755 5KS286ATE115 445 $1,850 G4-7D$Z1 2.3 E9128 5KS404SS308D15 1530 $6,502 G6-7S$ 8.13
E756 5KS324ATE115 606 $2,199 G4-7D$Z1 2.3 E9131 5KS405SS308D14 1490 $7,655 G6-7S$ 8.14
E757 5KS326ATE115 692 $2,650 G4-7D$Z1 2.3 E9133 5KS444SS308D13 1920 $10,462 G6-7S$ 8.14
E758 5KS364ATE115 686 $3,533 G4-7D$Z1 2.3 E9135 5KS445SS308D13 1960 $12,850 G6-7S$ 8.14
E759 5KS365ATE115 812 $4,641 G4-7D$Z1 2.3 E9137 5KS447SS308D11 2920 $14,377 G6-7S$ 8.14
E996 5KS324SS118D26 650 $2,938 G6-7S$ 8.13 E9139 5KS449SS309D14 2920 $17,600 G6-7S$ 8.14
E997 5KS326SS118D24 680 $3,814 G6-7S$ 8.13 E9141 5KS449SS319D12 2920 $17,600 G6-7S$ 8.14
E998 5KS364SS118D24 1000 $5,017 G6-7S$ 8.13 E9158 5KS324SS305D16 710 $3,096 G6-7S$ 8.13
E999 5KS365SS118D25 990 $6,300 G6-7S$ 8.14 E9161 5KS326SS305D15 730 $3,566 G6-7S$ 8.13
E7011 5KS213ATE305 128 $514 G4-7D$Z1 2.2 E9162 5KS324SS115D26 650 $2,938 G6-7S$ 8.13

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.6 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
E9163 5KS324SS205D24 730 $2,823 G6-7S$ 8.13 E9602 5KS182CSP304 76 $747 G6-7XP$ 8.10
E9164 5KS326SS115D24 680 $3,814 G6-7S$ 8.13 E9603 5KS184CSP305 101 $806 G6-7XP$ 8.10
Cross Reference Guide

E9165 5KS326SS205D24 740 $3,467 G6-7S$ 8.13 E9604 5KS184CSP304 101 $806 G6-7XP$ 8.10
E9384 5KS445XS204D18 2050 $13,710 G6-7S$8 8.16 E9605 5KS182CSP105 76 $762 G6-7XP$ 8.10
E9385 5KS447XS304D16 2940 $16,246 G6-7S$8 8.16 E9606 5KS182CSP104 76 $762 G6-7XP$ 8.10
E9387 5KS447XS204D18 2690 $16,386 G6-7S$8 8.16 E9607 5KS182CSP205 76 $730 G6-7XP$ 8.10
E9441 5KS324XS408D17 710 $4,963 G6-7S$8 8.15 E9608 5KS182CSP204 76 $730 G6-7XP$ 8.10
E9444 5KS324XS308 710 $3,715 G6-7S$8 8.15 E9610 5KS213CSP304 200 $951 G6-7XP$ 8.10
E9445 5KS326XS408 730 $5,864 G6-7S$8 8.15 E9611 5KS 184CSP105 101 $886 G6-7XP$ 8.10
E9448 5KS326XS308 730 $4,279 G6-7S$8 8.15 E9612 5KS184CSP104 101 $886 G6-7XP$ 8.10
E9449 5KS364XS408 1020 $6,946 G6-7S$8 8.15 E9613 5KS184CSP205 101 $813 G6-7XP$ 8.10
E9450 5KS324XS118 650 $3,526 G6-7S$8 8.15 E9614 5KS184CSP204 101 $813 G6-7XP$ 8.10
E9451 5KS324XS208 730 $3,388 G6-7S$8 8.15 E9616 5KS215CSP304 220 $1,233 G6-7XP$ 8.10
E9452 5KS364XS308 1070 $5,800 G6-7S$8 8.15 E9617 5KS213CSP104 200 $1,041 G6-7XP$ 8.10
E9453 5KS365XS408 1050 $8,574 G6-7S$8 8.15 E9618 5KS213CSP204 200 $1,036 G6-7XP$ 8.10
E9454 5KS326XS118 680 $4,577 G6-7S$8 8.15 E9619 5KS254QRA6EA8 315 $1,668 G6-7XP$ 8.10
E9455 5KS326XS208 740 $4,160 G6-7S$8 8.15 E9620 5KS215CSP104 220 $1,173 G6-7XP$ 8.10
E9456 5KS365XS308 1050 $6,659 G6-7S$8 8.15 E9621 5KS215CSP204 220 $1,195 G6-7XP$ 8.10
E9457 5KS404XS408 1500 $10,142 G6-7S$8 8.15 E9622 5KS256CSP304 350 $1,955 G6-7XP$ 8.10
E9458 5KS364XS118 1000 $6,271 G6-7S$8 8.15 E9623 5KS254CSP104 315 $1,629 G6-7XP$ 8.10
E9459 5KS364XS208 1060 $5,969 G6-7S$8 8.15 E9624 5KS254CSP204 315 $1,607 G6-7XP$ 8.10
E9460 5KS404XS308 1530 $7,672 G6-7S$8 8.15 E9625 5KS284CSP304 460 $2,606 G6-7XP$ 8.10
E9461 5KS405XS408 1530 $11,722 G6-7S$8 8.15 E9626 5KS256CSP104 350 $1,928 G6-7XP$ 8.11
E9462 5KS365XS118 990 $7,875 G6-7S$8 8.15 E9627 5KS256CSP204 350 $1,910 G6-7XP$ 8.11
E9463 5KS365XS208 1070 $7,566 G6-7S$8 8.15 E9628 5KS286CSP304 510 $3,064 G6-7XP$ 8.11
E9464 5KS405XS308 1490 $9,033 G6-7S$8 8.15 E9629 5KS284CSP114 460 $2,424 G6-7XP$ 8.11
E9465 5KS444XS408 1980 $15,215 G6-7S$8 8.15 E9630 5KS284CSP204 460 $2,338 G6-7XP$ 8.11
E9466 5KS405XS118 1480 $10,553 G6-7S$8 8.16 E9631 5KS286CSP114 510 $2,745 G6-7XP$ 8.11
E9467 5KS405XS208 1540 $9,192 G6-7S$8 8.16 E9632 5KS286CSP204 510 $2,635 G6-7XP$ 8.11
E9468 5KS444XS308 1920 $12,031 G6-7S$8 8.16 E9661 5KS213CSP105 200 $1,041 G6-7XP$ 8.10
E9469 5KS445XS408 2060 $19,139 G6-7S$8 8.16 E9662 5KS215CSP105 220 $1,173 G6-7XP$ 8.10
E9470 5KS444XS118 1990 $13,794 G6-7S$8 8.16 E9663 5KS254CSP105 315 $1,629 G6-7XP$ 8.10
E9471 5KS444XS208 1990 $11,793 G6-7S$8 8.16 E9664 5KS256CSP105 350 $1,928 G6-7XP$ 8.11
E9472 5KS445XS308 1960 $14,778 G6-7S$8 8.16 E9665 5SK284CSP115 460 $2,424 G6-7XP$ 8.11
E9473 5KS447XS408 2860 $21,818 G6-7S$8 8.16 E9666 5KS286CSP115 510 $2,745 G6-7XP$ 8.11
E9474 5KS445XS118 1990 $16,571 G6-7S$8 8.16 E9669 5KS213CSP205 200 $1,036 G6-7XP$ 8.10
E9475 5KS445XS208 2050 $13,710 G6-7S$8 8.16 E9671 5KS215CSP205 220 $1,195 G6-7XP$ 8.10
E9476 5KS447XS308 2920 $16,246 G6-7S$8 8.16 E9672 5KS254CSP205 315 $1,607 G6-7XP$ 8.10
E9477 5KS447XS118 2580 $20,963 G6-7S$8 8.16 E9673 5KS256CSP205 350 $1,910 G6-7XP$ 8.11
E9478 5KS447XS208 2690 $16,386 G6-7S$8 8.16 E9674 5KS284CSP205 460 $2,338 G6-7XP$ 8.11
E9510 5KS405SS118D8 1480 $8,442 G6-7S$ 8.14 E9675 5KS286CSP205 510 $2,635 G6-7XP$ 8.11
E9511 5KS444SS118 1990 $11,035 G6-7S$ 8.14 E9676 5KS324CS205 730 $3,618 G6-7XP$ 8.11
E9512 5KS445SS118D8 1990 $13,257 G6-7S$ 8.14 E9677 5KS326CS205 740 $4,262 G6-7XP$ 8.11
E9514 5KS449SS118D8 2620 $21,150 G6-7S$ 8.14 E9678 5KS213CSP305 200 $951 G6-7XP$ 8.10
E9534 5KS365SS404D8 1050 $7,145 G6-7S$ 8.13 E9679 5KS215CSP305 220 $1,233 G6-7XP$ 8.10
E9535 5KS404SS404D8 1500 $8,595 G6-7S$ 8.13 E9680 5KS254CSP305 315 $1,668 G6-7XP$ 8.10
E9536 5KS405SS404D8 1530 $9,934 G6-7S$ 8.13 E9682 5KS284CSP305 460 $2,606 G6-7XP$ 8.10
E9537 5KS444SS404D8 1980 $13,230 G6-7S$ 8.14 E9683 5KS286CSP305 510 $3,064 G6-7XP$ 8.11
E9538 5KS444SS114D8 1990 $11,035 G6-7S$ 8.14 E9685 5KS326CSP305 730 $4,361 G6-7XP$ 8.11
E9574 5KS324XS404 710 $4,963 G6-7S$8 8.15 E9686 5KS256CSP305 350 $1,955 G6-7XP$ 8.10
E9577 5KS324XS304 710 $3,715 G6-7S$8 8.15 E9693 5KS405XS204 1540 $9,192 G6-7S$8 8.16
E9578 5KS326XS404 730 $5,864 G6-7S$8 8.15 E9694 5KS444XS304 1930 $12,031 G6-7S$8 8.16
E9581 5KS326XS304 730 $4,279 G6-7S$8 8.15 E9695 5KS445XS404 2060 $19,139 G6-7S$8 8.16
E9582 5KS364XS404 1020 $6,946 G6-7S$8 8.15 E9697 5KS444XS204 1990 $11,793 G6-7S$8 8.16
E9583 5KS324XS114 680 $3,526 G6-7S$8 8.15 E9698 5KS445XS304 1960 $14,778 G6-7S$8 8.16
E9584 5KS324XS204 730 $3,388 G6-7S$8 8.15 E9699 5KS447XS404 2860 $21,818 G6-7S$8 8.16
E9585 5KS364XS304 1050 $5,800 G6-7S$8 8.15 E9748 5KS324SS408D8 710 $4,136 G6-7S$ 8.13
E9586 5KS365XS404 1050 $8,574 G6-7S$8 8.15 E9758 5KS324SS304D8 710 $3,096 G6-7S$ 8.13
E9587 5KS326XS114 700 $4,577 G6-7S$ 8.13 E9761 5KS326SS408D8 730 $4,887 G6-7S$ 8.13
E9588 5KS326XS204 740 $4,160 G6-7S$8 8.15 E9765 5KS326SS204D20 740 $3,467 G6-7S$ 8.13
E9589 5KS365XS304 1050 $6,659 G6-7S$8 8.15 E9767 5KS364SS408D8 1020 $5,788 G6-7S$ 8.13
E9590 5KS404XS404 1500 $10,142 G6-7S$8 8.15 E9768 5KS324SS204D20 730 $2,823 G6-7S$ 8.13
E9591 5KS364XS114 1000 $6,271 G6-7S$8 8.15 E9770 5KS365SS408D8 1050 $7,145 G6-7S$ 8.13
E9592 5KS364XS204 1060 $5,969 G6-7S$8 8.15 E9773 5KS404SS408D8 1500 $8,595 G6-7S$ 8.13
E9593 5KS404XS304 1530 $7,672 G6-7S$8 8.15 E9775 5KS365SS304D8 1050 $5,549 G6-7S$ 8.13
E9594 5KS405XS404 1530 $11,722 G6-7S$8 8.15 E9776 5KS364SS204D20 1060 $4,974 G6-7S$ 8.13
E9596 5KS365XS204 1070 $7,566 G6-7S$8 8.15 E9778 5KS405SS408D8 1530 $9,934 G6-7S$ 8.13
E9597 5KS405XS304 1490 $9,033 G6-7S$8 8.15 E9779 5KS405SS204D8 1540 $7,790 G6-7S$ 8.14
E9598 5KS444XS404 1980 $15,215 G6-7S$8 8.15 E9780 5KS444SS408D8 1930 $13,230 G6-7S$ 8.14
E9601 5KS182CSP305 76 $747 G6-7XP$ 8.10 E9781 5KS365SS204D20 1070 $6,305 G6-7S$ 8.14

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.7
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
E9782 5KS445SS408D8 2060 $16,643 G6-7S$ 8.14 M460 5KS145SAA422 50 $901 G4-7U1 3.2
E9784 5KS447SS408D8 2550 $19,308 G6-7S$ 8.14 M462 5KS143SAA125 43 $618 G4-7U1 3.2

Cross Reference Guide

E9820 5KS324SS108D20 650 $2,938 G6-7S$ 8.13 M463 5KS143SAA126 43 $618 G4-7U1 3.2
E9823 5KS326SS108D20 680 $3,814 G6-7S$ 8.13 M464 5KS145SAA233 50 $621 G4-7U1 3.2
E9829 5KS324SS114D20 650 $2,938 G6-7S$ 8.13 M465 5KS143SAA127 43 $692 G4-7U1 3.2
E9830 5KS365SS114 990 $6,300 G6-7S$ 8.14 M475 5KS143SAA208 43 $559 G4-7U1 3.2
E9831 5KS405SS114 1480 $8,442 G6-7S$ 8.14 M476 5KS145SAA308 50 $693 G4-7U1 3.2
E9832 5KS444SS204D8 2050 $10,255 G6-7S$ 8.14 M477 5KS145SAA404 50 $901 G4-7U1 3.2
E9834 5KS326SS304D8 730 $3,566 G6-7S$ 8.13 M478 5KS143SAA266 43 $523 G4-7U1 3.8
E9835 5KS364SS304 1070 $4,833 G6-7S$ 8.13 M479 5KS145SAA230 50 $531 G4-7U1 3.8
E9837 5KS404SS304D8 1530 $6,502 G6-7S$ 8.13 M480 5KS143SAA305 43 $502 G4-7U1 3.2
E9839 5KS326SS114D20 680 $3,814 G6-7S$ 8.13 M481 5KS143SAA304 43 $502 G4-7U1 3.2
E9845 5KS449SS328D8 2920 $17,600 G6-7S$ 8.14 M482 5KS143SAA205 43 $430 G4-7U1 3.2
E9846 5KS444SS304D8 1920 $10,462 G6-7S$ 8.14 M483 5KS143SAA204 43 $430 G4-7U1 3.2
E9847 5KS364SS114D20 1000 $5,017 G6-7S$ 8.13 M484 5KS145SAA305 50 $533 G4-7U1 3.2
E9851 5KS449SS204D8 2660 $18,192 G6-7S$ 8.14 M485 5KS145SAA304 50 $533 G4-7U1 3.2
E9854 5KS445SS204D8 2050 $11,922 G6-7S$ 8.14 M486 5KS143SAA105 43 $499 G4-7U1 3.2
E9868 5KS405SS304 1490 $7,655 G6-7S$ 8.14 M487 5KS143SAA104 43 $499 G4-7U1 3.2
E9869 5KS447SS304D8 2920 $14,377 G6-7S$ 8.14 M488 5KS145SAA205 50 $526 G4-7U1 3.2
E9870 5KS445SS304D8 1960 $12,850 G6-7S$ 8.14 M489 5KS145SAA204 50 $526 G4-7U1 3.2
E9906 5KS449SS209D8 2890 $19,113 G6-7S$ 8.14 M490 5KS145SAA105 50 $532 G4-7U1 3.2
E9915 5KS324SS208 730 $2,823 G6-7S$ 8.13 M491 5KS145SAA104 50 $532 G4-7U1 3.2
E9916 5KS324SS218D20 730 $2,823 G6-7S$ 8.13 M492 5KS145SAA209 50 $478 G4-7U1 3.2
E9917 5KS326SS208D20 740 $3,467 G6-7S$ 8.13 M493 5KS145SAA210 50 $478 G4-7U1 3.2
E9918 5KS326SS218D20 740 $3,467 G6-7S$ 8.13 M494 5KS145SAA208 50 $526 G4-7U1 3.2
E9919 5KS364SS208D20 1060 $4,974 G6-7S$ 8.13 M496 5KS143SAA300 43 $555 G4-7U1 3.8
E9921 5KS364SS218D20 1060 $4,974 G6-7S$ 8.13 M497 5KS143SAA209 43 $483 G4-7U1 3.8
E9922 5KS365SS208 1070 $6,305 G6-7S$ 8.14 M498 5KS145SAA303 50 $586 G4-7U1 3.8
E9923 5KS365SS218D20 1070 $6,305 G6-7S$ 8.14 M499 5KS145SAA231 50 $531 G4-7U1 3.8
E9924 5KS405SS208 1540 $7,790 G6-7S$ 8.14 M500 5KS145SAA220 50 $579 G4-7U1 3.8
E9925 5KS405SS218D8 1540 $7,790 G6-7S$ 8.14 M520 5KS143XAA266 43 $763 G4-7UX1 3.22
E9926 5KS444SS208 2050 $10,255 G6-7S$ 8.14 M521 5KS145XAA230 50 $857 G4-7UX1 3.22
E9927 5KS444SS218D8 2050 $10,255 G6-7S$ 8.14 M526 5KS145XAA223 50 $981 G4-7UX1 3.22
E9928 5KS445SS208D8 2050 $11,922 G6-7S$ 8.14 M990 5KS213SAA108 200 $930 G4-7U1 3.3
E9929 5KS445SS218D8 2050 $11,922 G6-7S$ 8.14 M991 5KS215SAA108 220 $1,090 G4-7U1 3.4
E9933 5KS449SS208D8 2660 $18,192 G6-7S$ 8.14 M992 5KS254SAA108 315 $1,496 G4-7U1 3.4
E9958 5KS447SS208D8 2520 $14,501 G6-7S$ 8.14 M993 5KS256SAA108 350 $1,801 G4-7U1 3.4
E9959 5KS447SS204D8 2520 $14,501 G6-7S$ 8.14 M994 5KS284SAA118 460 $2,256 G4-7U1 3.4
E9961 5KS447SS118D8 2580 $16,770 G6-7S$ 8.14 M995 5KS286SAA118 510 $2,653 G4-7U1 3.5
E9988 KS449SS2210D8 2660 $18,192 G6-7S$ 8.14 M996 5KS324SAA118 670 $3,301 G4-7U1 3.5
E9989 KS449SS2211D8 2660 $18,192 G6-7S$ 8.14 M997 5KS326SAA118 700 $4,223 G4-7U1 3.5
E9990 KS449SS2212D8 2890 $19,113 G6-7S$ 8.14 M998 5KS364SAA118 940 $5,877 G4-7U 3.6
E9991 KS447SS280D8 2520 $14,501 G6-7S$ 8.14 M999 5KS365SAA118 970 $7,215 G4-7U 3.6
F786 5KC182BC213 77 $495 G4-7FAZ 8.5 M6621 5KS184XAA261 101 $1,315 G4-7UXHE 3.30
F787 5KC182BC214 79 $476 G4-7FAZ 8.5 M6622 5KS213XAA278 200 $1,710 G4-7UXHE 3.30
F788 5KC184BC217 92 $561 G4-7FAZ 8.5 M6623 5KS215XAA259 220 $1,789 G4-7UXHE 3.30
F789 5KC184BC214 95 $518 G4-7FAZ 8.5 M6624 5KS254XAA267 315 $2,122 G4-7UXHE 3.30
F790 5KC184BC218 103 $665 G4-7FAZ 8.5 M6625 5KS256XAA254 350 $2,439 G4-7UXHE 3.30
F791 5KC215BC214 143 $765 G4-7FAZ 8.5 M6626 5KS284XAA259 460 $2,842 G4-7UXHE 3.30
F792 5KC184BC219 103 $601 G4-7FAZ 8.5 M6627 5KS286XAA255 510 $3,250 G4-7UXHE 3.30
F793 5KC215BC215 178 $1,000 G4-7FAZ 8.5 M6628 5KS324XAA271 710 $4,465 G4-7UXHE 3.30
F794 5KC215BC219 183 $1,200 G4-7FAZ 8.5 M6629 5KS326XAA253 740 $5,029 G4-7UXHE 3.30
F795 5KC215BC217 183 $1,200 G4-7FAZ 8.5 M6630 5KS364XAA250W6 1020 $7,556 G4-7UXHE 3.30
F798 5KC215BC218 178 $1,000 G4-7FAZ 8.5 M6631 5KS364XAA249W8 1020 $7,556 G4-7UXHE 3.30
F835 5KC143BC201 48 $350 G4-7FAZ 8.5 M6632 5KS365XAA253W6 1090 $8,779 G4-7UXHE 3.30
F836 5KC145BC201 65 $365 G4-7FAZ 8.5 M6633 5KS365XAA254W8 1090 $8,779 G4-7UXHE 3.30
F837 5KC56BC201 42 $267 G4-7FAZ 8.5 M7700 5KS143STE105 52 $328 G4-7S$P 2.6
M240 5KS184SAA105 101 $712 G4-7U1 3.3 M7701 5KS143STE109 52 $365 G4-7S$P 2.6
M241 5KS182SAA205 76 $583 G4-7U1 3.3 M7702 5KS145STE105 52 $426 G4-7S$P 2.6
M242 5KS184SAA205 101 $684 G4-7U1 3.3 M7703 5KS182STE105 96 $479 G4-7S$P 2.6
M352 5KS143XAA208 43 $680 G4-7UX1 3.18 M7704 5KS184STE105 106 $593 G4-7S$P 2.6
M353 5KS143XAA204 43 $680 G4-7UX1 3.18 M7705 5KS213STE105 168 $717 G4-7S$P 2.6
M354 5KS143XAA308 43 $672 G4-7UX1 3.18 M7706 5KS215STE105 192 $838 G4-7S$P 2.6
M355 5KS143XAA304 43 $672 G4-7UX1 3.18 M7707 5KS254STE105 290 $1,151 G4-7S$P 2.6
M359 5KS145XAA208 50 $771 G4-7UX1 3.18 M7708 5KS256STE105 325 $1,426 G4-7S$P 2.6
M360 5KS145XAA204 50 $771 G4-7UX1 3.18 M7709 5KS284STE115 445 $1,637 G4-7S$P 2.6
M361 5KS145XAA211 50 $833 G4-7UX1 3.18 M7710 5KS286STE115 465 $1,911 G4-7S$P 2.6
M362 5KS145XAA210 50 $833 G4-7UX1 3.18 M7711 5KS324STE115 640 $2,452 G4-7S$P 2.6
M363 5KS145XAA308 50 $728 G4-7UX1 3.18 M7712 5KS324STE105 650 $2,452 G4-7S$P 2.6
M364 5KS145XAA304 50 $728 G4-7UX1 3.18 M7713 5KS326STE115 700 $3,173 G4-7S$P 2.6

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.8 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
M7714 5KS326STE105 710 $3,173 G4-7S$P 2.6 M8907 5KS143XAA125 43 $862 G4-7UX1 3.18
M7715 5KS182STE122 88 $505 G4-7S$P1 2.8 M8908 5KS143XAA126 43 $862 G4-7UX1 3.18
Cross Reference Guide

M7716 5KS184STE122 112 $620 G4-7S$P1 2.8 M8909 5KS182XAA207 76 $766 G4-7UX1 3.22
M7717 5KS213STE122 151 $810 G4-7S$P1 2.8 M8910 5KS184XAA202 101 $880 G4-7UX1 3.22
M7718 5KS215STE122 190 $966 G4-7S$P1 2.8 M8911 5KS213XAA200 200 $1,159 G4-7UX1 3.22
M7719 5KS254STE122 287 $1,250 G4-7S$P1 2.8 M8912 5KS215XAA203 220 $1,386 G4-7UX1 3.22
M7720 5KS256STE122 344 $1,640 G4-7S$P1 2.8 M8913 5KS254XAA200 315 $1,818 G4-7UX1 3.22
M7721 5KS284STE112 477 $1,950 G4-7S$P1 2.8 M8914 5KS256XAA200 350 $2,241 G4-7UX1 3.22
M7722 5KS286STE112 522 $2,300 G4-7S$P1 2.8 M8915 5KS284XAA200 460 $2,685 G4-7UX1 3.22
M7723 5KS143STE205 52 $332 G4-7S$P 2.6 M8916 5KS286XAA200 510 $3,091 G4-7UX1 3.22
M7724 5KS145STE209 58 $369 G4-7S$P 2.6 M8917 5KS365XAA114 1020 $8,174 G4-7UX 3.20
M7725 5KS145STE205 58 $406 G4-7S$P 2.6 M8918 5KS405XAA123 1530 $10,522 G4-7UX 3.21
M7726 5KS182STE205 96 $450 G4-7S$P 2.6 M8919 5KS444XAA122 1790 $13,446 G4-7UX 3.21
M7727 5KS184STE205 106 $425 G4-7S$P 2.6 M8920 5KS445XAA122 1930 $15,916 G4-7UX 3.21
M7728 5KS213STE205 168 $713 G4-7S$P 2.6 M8921 5KS284XAA300 460 $3,050 G4-7UX1 3.22
M7729 5KS215STE205 192 $859 G4-7S$P 2.6 M8922 5KS286XAA300 510 $3,679 G4-7UX1 3.22
M7730 5KS254STE205 290 $1,131 G4-7S$P 2.6 M8923 5KS284XAA100 460 $2,804 G4-7UX1 3.22
M7731 5KS256STE205 325 $1,409 G4-7S$P 2.6 M8924 5KS286XAA100 510 $3,243 G4-7UX1 3.22
M7732 5KS284STE205 430 $1,562 G4-7S$P 2.6 M8925 5KS182XAA100 76 $814 G4-7UX1 3.22
M7733 5KS286STE205 475 $1,760 G4-7S$P 2.6 M8926 5KS182XAA300 76 $789 G4-7UX1 3.22
M7734 5KS324STE205 650 $2,348 G4-7S$P 2.6 M8927 5KS184XAA100 101 $989 G4-7UX1 3.22
M7735 5KS324STE215 640 $2,348 G4-7S$P 2.6 M8928 5KS184XAA300 101 $871 G4-7UX1 3.22
M7736 5KS326STE205 710 $2,884 G4-7S$P 2.6 M8929 5KS213XAA101 200 $1,166 G4-7UX1 3.22
M7737 5KS326STE215 700 $2,884 G4-7S$P 2.6 M8931 5KS215XAA100 220 $1,347 G4-7UX1 3.22
M7738 5KS143STE222 50 $360 G4-7S$P1 2.8 M8932 5KS215XAA300 220 $1,430 G4-7UX1 3.22
M7739 5KS145STE222 61 $390 G4-7S$P1 2.8 M8933 5KS254XAA100 315 $1,845 G4-7UX1 3.22
M7740 5KS145STE229 64 $440 G4-7S$P1 2.8 M8934 5KS254XAA300 315 $1,898 G4-7UX1 3.22
M7741 5KS182STE222 92 $485 G4-7S$P1 2.8 M8935 5KS256XAA100 350 $2,258 G4-7UX1 3.22
M7742 5KS184STE222 117 $575 G4-7S$P1 2.8 M8936 5KS256XAA300 350 $2,292 G4-7UX1 3.22
M7743 5KS213STE222 155 $810 G4-7S$P1 2.8 M8937 5KS449XAA420 3150 $26,105 G4-7UX 3.21
M7744 5KS215STE222 203 $966 G4-7S$P1 2.8 M8938 5KS449XAA422 3120 $26,105 G4-7UX 3.21
M7745 5KS254STE222 285 $1,260 G4-7S$P1 2.8 M8939 5KS447XAA122 2560 $19,819 G4-7UX 3.21
M7746 5KS256STE222 329 $1,640 G4-7S$P1 2.8 M8940 5KS449XAA322 3070 $20,142 G4-7UX 3.21
M7747 5KS284STE222 482 $1,950 G4-7S$P1 2.8 M8941 5KS449XAA323 3070 $20,142 G4-7UX 3.21
M7748 5KS286STE222 508 $2,250 G4-7S$P1 2.8 M8942 5KS449XAA409 3120 $27,500 G4-7UX 3.21
M7749 5KS284STE105 445 $1,637 G4-7S$P 2.6 M8943 5KS449XAA123 2770 $25,052 G4-7UX 3.21
M7750 5KS286STE105 475 $1,911 G4-7S$P 2.6 M8944 5KS449XAA124 2770 $25,052 G4-7UX 3.21
M7907 5KS364LAA114A 930 $5,757 G4-7S$P 2.6 M8945 5KS449XAA224 2790 $20,436 G4-7UX 3.21
M7909 5KS364LAA118B 930 $5,757 G4-7S$P 2.6 M8946 5KS449XAA225 2790 $20,436 G4-7UX 3.21
M7910 5KS365LAA114A 970 $7,067 G4-7S$P 2.6 M8950 5KS324SAA404 649 $4,504 G4-7U1 3.4
M7912 5KS365LAA118B 970 $7,067 G4-7S$P 2.6 M8953 5KS445SAA420 2020 $19,025 G4-7U 3.6
M7913 5KS405LAA114B 1,420 $9,151 G4-7S$P 2.7 M8954 5KS447SAA420 2580 $21,185 G4-7U 3.6
M7914 5KS405LAA118C 1,420 $9,151 G4-7S$P 2.7 M8955 5KS445SAA121 1860 $14,674 G4-7U 3.7
M7915 5KS444LAA114B 1,780 $11,416 G4-7S$P 2.7 M8956 5KS449SAA420 3120 $23,102 G4-7U 3.7
M7916 5KS444LAA118C 1,780 $11,953 G4-7S$P 2.7 M8957 5KS447SAA120 2560 $18,577 G4-7U 3.7
M7917 5KS445LAA114A 1,810 $13,728 G4-7S$P 2.7 M8959 5KS449SAA122 2770 $23,935 G4-7U 3.7
M7918 5KS445LAA118B 1,830 $13,728 G4-7S$P 2.7 M8960 5KS449SAA123 2790 $29,681 G4-7U 3.7
M7919 5KS447LAA114B 2,420 $17,379 G4-7S$P 2.7 M8961 5KS449SAA124 2790 $29,681 G4-7U 3.7
M7920 5KS447LAA118C 2,420 $17,379 G4-7S$P 2.7 M8962 5KS449SAA223 3030 $22,654 G4-7U 3.7
M7921 5KS449LAA114A 2,580 $22,392 G4-7S$P 2.7 M8963 5KS449SAA301 3150 $24,120 G4-7U 3.7
M7922 5KS449LAA118B 2,580 $22,392 G4-7S$P 2.7 M8964 5KS324SAA152 670 $3,514 G4-7U1 3.8
M7929 5KS364LAA204A 990 $5,637 G4-7S$P 2.6 M8965 5KS324SAA2007 710 $3,485 G4-7U1 3.8
M7931 5KS364LAA208B 990 $5,637 G4-7S$P 2.6 M8966 5KS326SAA146 700 $4,436 G4-7U1 3.8
M7932 5KS365LAA204A 1,040 $6,834 G4-7S$P 2.6 M8967 5KS326SAA271 740 $4,109 G4-7U1 3.8
M7934 5KS365LAA208B 1,040 $6,834 G4-7S$P 2.6 M8971 5KS324XAA175 670 $4,389 G4-7UX1 3.22
M7935 5KS405LAA204A 1,450 $8,441 G4-7S$P 2.7 M8972 5KS324XAA279 710 $4,264 G4-7UX1 3.22
M7936 5KS405LAA208B 1,450 $8,441 G4-7S$P 2.7 M8973 5KS326XAA155 700 $5,311 G4-7UX1 3.22
M7937 5KS444LAA204A 1,860 $10,606 G4-7S$P 2.7 M8974 5KS326XAA263 740 $4,829 G4-7UX1 3.22
M7938 5KS444LAA208B 1,880 $10,606 G4-7S$P 2.7 M8975 5KS405XAA125 1530 $10,522 G4-7UX 3.21
M7939 5KS445LAA204A 1,990 $12,339 G4-7S$P 2.7 M8976 5KS444XAA124 1880 $13,446 G4-7UX 3.21
M7940 5KS445LAA208B 2,020 $12,339 G4-7S$P 2.7 M8977 5KS445XAA125 2000 $15,916 G4-7UX 3.21
M7941 5KS447LAA204B 2,560 $15,478 G4-7S$P 2.7 M8978 5KS447XAA124 2630 $19,819 G4-7UX 3.21
M7942 5KS447LAA208C 2,580 $15,478 G4-7S$P 2.7 M8979 5KS449XAA125 2770 $25,052 G4-7UX 3.21
M7943 5KS449LAA204A 2,660 $18,099 G4-7S$P 2.7 M8982 5KGS364SAA320 1000 $7,439 G4-7UC 3.9
M7944 5KS449LAA208B 2,660 $18,099 G4-7S$P 2.7 M8983 5KGS365SAA320 1030 $8,507 G4-7UC 3.9
M8901 5KS145XAA420 50 $1,108 G4-7UX1 3.18 M8984 5KGS404SAA320 1480 $9,999 G4-7UC 3.9
M8903 5KS143XAA121 43 $690 G4-7UX1 3.18 M8985 5KGS405SAA321 1530 $11,000 G4-7UC 3.9
M8904 5KS143XAA123 43 $690 G4-7UX1 3.18 M8986 5KGS444SAA320 1920 $14,854 G4-7UC 3.9
M8905 5KS143XAA122 43 $720 G4-7UX1 3.18 M8988 5KGS447SAA320 2700 $21,313 G4-7UC 3.9
M8906 5KS143XAA124 43 $720 G4-7UX1 3.18 M8989 5KGS449SAA321 3070 $23,639 G4-7UC 3.9

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.9
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
M8992 5KGS364SAA220 1030 $7,420 G4-7UC 3.9 M9321 5KAF445SAA221 2050 4.8
M8993 5KGS365SAA220 1090 $8,826 G4-7UC 3.9 M9322 5KAF445SAA220 2050 4.8

Cross Reference Guide

M8994 5KGS405SAA221 1500 $10,946 G4-7UC 3.9 M9323 5KAF445SAA221 2050 4.8
M8995 5KGS444SAA220 1970 $14,473 G4-7UC 3.9 M9324 5KAF449SAA221 2830 4.8
M8996 5KGS445SAA220 2060 $16,604 G4-7UC 3.9 M9325 5KAF449SAA222 2870 4.8
M8997 5KGS447SAA220 2700 $20,755 G4-7UC 3.9 M9326 5KAF449SAA223 3110 4.8
M8998 5KGS449SAA222 2980 $23,135 G4-7UC 3.9 M9327 5KAF449SAA224 2890 4.8
M8999 5KGS449SAA224 3100 $26,938 G4-7UC 3.9 M9384 5KS445XAA204 2060 $14,287 G4-7UX 3.21
M9111 5KS213SAA308 200 $820 G4-7U1 3.3 M9385 5KS447XAA304 2860 $18,108 G4-7UX 3.21
M9112 5KS215SAA308 220 $1,165 G4-7U1 3.3 M9387 5KS447XAA204 2800 $17,614 G4-7UX 3.21
M9113 5KS254SAA308 315 $1,547 G4-7U1 3.3 M9413 5KS182XAA408 76 $889 G4-7UX1 3.18
M9114 5KS256SAA308 350 $1,898 G4-7U1 3.4 M9414 5KS182XAA308 76 $697 G4-7UX1 3.18
M9115 5KS284SAA308 460 $2,525 G4-7U1 3.4 M9415 5KS184XAA408 101 $1,051 G4-7UX1 3.18
M9117 5KS286SAA308 510 $3,083 G4-7U1 3.4 M9416 5KS184XAA308 101 $779 G4-7UX1 3.18
M9119 5KS324SAA308 700 $3,668 G4-7U1 3.4 M9417 5KS213XAA408 200 $1,354 G4-7UX1 3.18
M9122 5KS326SAA308 730 $4,184 G4-7U1 3.5 M9418 5KS182XAA108 76 $718 G4-7UX1 3.18
M9124 5KS364SAA308 1030 $5,771 G4-7U 3.5 M9419 5KS182XAA208 76 $674 G4-7UX1 3.18
M9126 5KS365SAA308 1070 $6,700 G4-7U 3.5 M9420 5KS213XAA308 200 $950 G4-7UX1 3.18
M9128 5KS404SAA308 1480 $7,794 G4-7U 3.6 M9421 5KS215XAA408 220 $1,747 G4-7UX1 3.18
M9131 5KS405SAA308 1540 $8,664 G4-7U 3.6 M9422 5KS184XAA108 101 $889 G4-7UX1 3.19
M9133 5KS444SAA308 2060 $11,669 G4-7U 3.6 M9423 5KS184XAA208 101 $788 G4-7UX1 3.19
M9135 5KS445SAA308 2130 $14,057 G4-7U 3.6 M9424 5KS215XAA308 220 $1,338 G4-7UX1 3.19
M9137 5KS447SAA308 2860 $17,030 G4-7U 3.7 M9425 5KS254XAA408 315 $2,410 G4-7UX1 3.19
M9139 5KS449SAA309 3070 $19,053 G4-7U 3.7 M9426 5KS213XAA108 200 $1,074 G4-7UX1 3.19
M9141 5KS449SAA319 3070 $19,053 G4-7U 3.7 M9427 5KS213XAA208 200 $1,067 G4-7UX1 3.19
M9142 5KS213SAA305 200 $820 G4-7U1 3.3 M9428 5KS254XAA308 315 $1,778 G4-7UX1 3.19
M9143 5KS215SAA305 220 $1,165 G4-7U1 3.3 M9429 5KS256XAA408 350 $3,051 G4-7UX1 3.19
M9144 5KS213SAA105 200 $930 G4-7U1 3.3 M9430 5KS215XAA108 220 $1,255 G4-7UX1 3.19
M9145 5KS213SAA205 200 $924 G4-7U1 3.3 M9431 5KS215XAA208 220 $1,286 G4-7UX1 3.19
M9146 5KS254SAA305 315 $1,547 G4-7U1 3.3 M9432 5KS256XAA308 350 $2,173 G4-7UX1 3.19
M9147 5KS215SAA105 220 $1,090 G4-7U1 3.4 M9433 5KS284XAA408 460 $3,617 G4-7UX1 3.19
M9148 5KS215SAA205 220 $1,031 G4-7U1 3.4 M9434 5KS254XAA108 315 $1,725 G4-7UX1 3.19
M9149 5KS256SAA305 350 $1,898 G4-7U1 3.4 M9435 5KS254XAA208 315 $1,694 G4-7UX1 3.19
M9150 5KS254SAA105 315 $1,496 G4-7U1 3.4 M9436 5KS284XAA308 460 $2,882 G4-7UX1 3.19
M9151 5KS254SAA205 315 $1,418 G4-7U1 3.4 M9437 5KS286XAA408 510 $4,726 G4-7UX1 3.19
M9152 5KS284SAA305 460 $2,525 G4-7U1 3.4 M9438 5KS256XAA108 350 $2,135 G4-7UX1 3.19
M9153 5KS256SAA105 350 $1,801 G4-7U1 3.4 M9439 5KS256XAA208 350 $2,111 G4-7UX1 3.19
M9154 5KS256SAA205 350 $1,694 G4-7U1 3.4 M9440 5KS286XAA308 510 $3,512 G4-7UX1 3.19
M9155 5KS286SAA305 510 $3,083 G4-7U1 3.4 M9441 5KS324XAA408 670 $5,459 G4-7UX1 3.19
M9156 5KS284SAA115 460 $2,256 G4-7U1 3.4 M9442 5KS284XAA118 460 $2,632 G4-7UX1 3.20
M9157 5KS284SAA205 460 $2,162 G4-7U1 3.4 M9443 5KS284XAA208 460 $2,514 G4-7UX1 3.20
M9158 5KS324SAA305 679 $3,668 G4-7U1 3.4 M9444 5KS324XAA308 700 $4,446 G4-7UX1 3.20
M9159 5KS286SAA115 510 $2,653 G4-7U1 3.5 M9445 5KS326XAA408 710 $6,538 G4-7UX1 3.20
M9160 5KS286SAA205 510 $2,525 G4-7U1 3.5 M9446 5KS286XAA118 510 $3,073 G4-7UX1 3.20
M9161 5KS326SAA305 730 $4,184 G4-7U1 3.5 M9447 5KS286XAA208 510 $2,922 G4-7UX1 3.20
M9162 5KS324SAA115 670 $3,301 G4-7U1 3.5 M9448 5KS326XAA308 730 $4,962 G4-7UX1 3.20
M9163 5KS324SAA205 710 $3,272 G4-7U1 3.5 M9449 5KS364XAA408 1010 $8,073 G4-7UX 3.20
M9164 5KS326SAA115 700 $4,223 G4-7U1 3.5 M9450 5KS324XAA118 670 $4,176 G4-7UX1 3.20
M9165 5KS326SAA205 740 $3,836 G4-7U1 3.5 M9451 5KS324XAA208 710 $4,051 G4-7UX1 3.20
M9300 5KAF143SAB2174 43 4.8 M9452 5KS364XAA308 1030 $6,633 G4-7UX 3.20
M9301 5KAF145SAB2165 43 4.8 M9453 5KS365XAA408 1090 $9,958 G4-7UX 3.20
M9302 5KAF182SAB2207 76 4.8 M9454 5KS326XAA118 700 $5,098 G4-7UX1 3.20
M9303 5KAF184SAB2205 101 4.8 M9455 5KS326XAA208 740 $4,615 G4-7UX1 3.20
M9304 5KAF213SAB2216 200 4.8 M9456 5KS365XAA308 1070 $7,562 G4-7UX 3.20
M9305 5KAF215SAB2210 220 4.8 M9457 5KS404XAA408 1490 $12,015 G4-7UX 3.20
M9306 5KAF254SAB2215 315 4.8 M9458 5KS364XAA118 940 $6,837 G4-7UX 3.20
M9307 5KAF256SAB2196 350 4.8 M9459 5KS364XAA208 1020 $6,616 G4-7UX 3.20
M9308 5KAF284SAB2183 460 4.8 M9460 5KS404XAA308 1480 $8,830 G4-7UX 3.20
M9309 5KAF286SAB2182 510 4.8 M9461 5KS405XAA408 1570 $13,560 G4-7UX 3.20
M9310 5KAF324SAA2222 690 4.8 M9462 5KS365XAA118 1020 $8,174 G4-7UX 3.20
M9311 5KAF326SAA222 740 4.8 M9463 5KS365XAA208 1090 $7,839 G4-7UX 3.20
M9312 5KAF364SAA222 1040 4.8 M9464 5KS405XAA308 1540 $9,698 G4-7UX 3.20
M9313 5KAF364SAA223 1060 4.8 M9465 5KS444XAA408 1950 $16,966 G4-7UX 3.20
M9314 5KAF365SAA223 1070 4.8 M9466 5KS405XAA118 1530 $10,522 G4-7UX 3.21
M9315 5KAF365SAA224 1070 4.8 M9467 5KS405XAA208 1480 $9,651 G4-7UX 3.21
M9316 5KAF405SAA221 1560 4.8 M9468 5KS444XAA308 2060 $12,482 G4-7UX 3.21
M9317 5KAF405SAA220 1560 4.8 M9469 5KS445XAA408 2020 $21,498 G4-7UX 3.21
M9318 5KAF444SAA220 2050 4.8 M9470 5KS444XAA118 1790 $13,446 G4-7UX 3.21
M9319 5KAF405SAA221 1560 4.8 M9471 5KS444XAA208 1970 $12,434 G4-7UX 3.21
M9320 5KAF445SAA220 2050 4.8 M9472 5KS445XAA308 2130 $14,871 G4-7UX 3.21

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.10 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
M9473 5KS447XAA408 2580 $23,939 G4-7UX 3.21 M9698 5KS445XAA304 2130 $14,871 G4-7UX 3.21
M9474 5KS445XAA118 1930 $15,916 G4-7UX 3.21 M9699 5KS447XAA404 2580 $23,939 G4-7UX 3.21
Cross Reference Guide

M9475 5KS445XAA208 2090 $14,287 G4-7UX 3.21 M9702 5KS182SAA305 76 $604 G4-7U1 3.2
M9476 5KS447XAA308 2860 $18,108 G4-7UX 3.21 M9703 5KS182SAA304 76 $604 G4-7U1 3.2
M9477 5KS447XAA118 2560 $19,819 G4-7UX 3.21 M9704 5KS184SAA305 101 $675 G4-7U1 3.2
M9478 5KS447XAA208 2800 $17,614 G4-7UX 3.21 M9705 5KS213SAA408 200 $1,155 G4-7U1 3.2
M9482 5KS182XAA404 76 $889 G4-7UX1 3.18 M9706 5KS184SAA304 101 $675 G4-7U1 3.2
M9483 5KS182XAA304 76 $697 G4-7UX1 3.18 M9708 5KS215SAA408 220 $1,443 G4-7U1 3.3
M9485 5KS184XAA404 101 $1,051 G4-7UX1 3.18 M9711 5KS182SAA204 76 $583 G4-7U1 3.3
M9486 5KS184XAA304 101 $779 G4-7UX1 3.18 M9712 5KS213SAA304 200 $820 G4-7U1 3.3
M9487 5KS213XAA404 200 $1,354 G4-7UX1 3.18 M9713 5KS182SAA105 76 $600 G4-7U1 3.3
M9488 5KS182XAA104 76 $718 G4-7UX1 3.18 M9715 5KS182SAA104 76 $600 G4-7U1 3.3
M9489 5KS182XAA204 76 $674 G4-7UX1 3.18 M9717 5KS215SAA304 220 $1,165 G4-7U1 3.3
M9490 5KS213XAA304 200 $950 G4-7UX1 3.18 M9718 5KS184SAA204 101 $684 G4-7U1 3.3
M9491 5KS215XAA404 220 $1,747 G4-7UX1 3.18 M9719 5KS254SAA408 315 $1,917 G4-7U1 3.3
M9492 5KS184XAA104 101 $889 G4-7UX1 3.19 M9722 5KS184SAA104 101 $712 G4-7U1 3.3
M9493 5KS184XAA204 101 $788 G4-7UX1 3.19 M9724 5KS256SAA408 350 $2,423 G4-7U1 3.3
M9494 5KS215XAA304 220 $1,338 G4-7UX1 3.19 M9726 5KS254SAA304 315 $1,547 G4-7U1 3.3
M9495 5KS254XAA404 315 $2,410 G4-7UX1 3.19 M9728 5KS213SAA104 200 $930 G4-7U1 3.3
M9496 5KS213XAA104 200 $1,074 G4-7UX1 3.19 M9730 5KS213SAA204 200 $924 G4-7U1 3.3
M9497 5KS213XAA204 200 $1,067 G4-7UX1 3.19 M9733 5KS215SAA104 220 $1,090 G4-7U1 3.4
M9498 5KS254XAA304 315 $1,778 G4-7UX1 3.19 M9736 5KS284SAA408 460 $2,828 G4-7U1 3.4
M9499 5KS256XAA404 350 $3,051 G4-7UX1 3.19 M9737 5KS256SAA304 350 $1,898 G4-7U1 3.4
M9510 5KS405SAA118 1530 $9,342 G4-7U 3.6 M9738 5KS215SAA204 220 $1,031 G4-7U1 3.4
M9511 5KS444SAA118 1790 $12,203 G4-7U 3.6 M9741 5KS254SAA104 315 $1,496 G4-7U1 3.4
M9512 5KS445SAA118 1860 $14,674 G4-7U 3.7 M9742 5KS286SAA408 510 $3,684 G4-7U1 3.4
M9514 5KS449SAA118 2770 $23,935 G4-7U 3.7 M9745 5KS254SAA204 315 $1,418 G4-7U1 3.4
M9534 5KS365SAA404 1090 $8,096 G4-7U 3.5 M9746 5KS284SAA304 460 $2,525 G4-7U1 3.4
M9535 5KS404SAA404 1490 $9,769 G4-7U 3.5 M9748 5KS324SAA408 670 $4,504 G4-7U1 3.4
M9536 5KS405SAA404 1570 $12,000 G4-7U 3.6 M9749 5KS256SAA104 350 $1,801 G4-7U1 3.4
M9537 5KS444SAA404 1950 $15,015 G4-7U 3.6 M9751 5KS256SAA204 350 $1,694 G4-7U1 3.4
M9538 5KS444SAA114 1790 $12,203 G4-7U 3.6 M9755 5KS286SAA304 510 $3,083 G4-7U1 3.4
M9563 5KS215XAA104 220 $1,255 G4-7UX1 3.19 M9758 5KS324SAA304 700 $3,668 G4-7U1 3.4
M9564 5KS215XAA204 220 $1,286 G4-7UX1 3.19 M9759 5KS284SAA204 460 $2,162 G4-7U1 3.4
M9565 5KS256XAA304 350 $2,173 G4-7UX1 3.19 M9761 5KS326SAA408 710 $5,613 G4-7U1 3.4
M9566 5KS284XAA404 460 $3,617 G4-7UX1 3.19 M9762 5KS326SAA404 710 $5,613 G4-7U1 3.4
M9567 5KS254XAA104 315 $1,725 G4-7UX1 3.19 M9764 5KS286SAA204 510 $2,525 G4-7U1 3.5
M9568 5KS254XAA204 315 $1,694 G4-7UX1 3.19 M9765 5KS326SAA204 740 $3,836 G4-7U1 3.5
M9569 5KS284XAA304 460 $2,882 G4-7UX1 3.19 M9766 5KS364SAA404 1010 $6,564 G4-7U 3.5
M9570 5KS286XAA404 510 $4,726 G4-7UX1 3.19 M9767 5KS364SAA408 1010 $6,564 G4-7U 3.5
M9571 5KS256XAA104 350 $2,135 G4-7UX1 3.19 M9768 5KS324SAA204 710 $3,272 G4-7U1 3.5
M9572 5KS256XAA204 350 $2,111 G4-7UX1 3.19 M9770 5KS365SAA408 1090 $8,096 G4-7U 3.5
M9573 5KS286XAA304 510 $3,512 G4-7UX1 3.19 M9773 5KS404SAA408 1490 $9,769 G4-7U 3.5
M9574 5KS324XAA404D1 670 $5,459 G4-7UX1 3.19 M9775 5KS365SAA304 1070 $6,700 G4-7U 3.5
M9575 5KS284XAA114 460 $2,632 G4-7UX1 3.20 M9776 5KS364SAA204 1020 $5,755 G4-7U 3.6
M9576 5KS284XAA204 460 $2,514 G4-7UX1 3.20 M9778 5KS405SAA408 1570 $12,000 G4-7U 3.6
M9577 5KS324XAA304 700 $4,446 G4-7UX1 3.20 M9779 5KS405SAA204 1480 $8,617 G4-7U 3.6
M9578 5KS326XAA404 710 $6,538 G4-7UX1 3.20 M9780 5KS444SAA408 1950 $15,015 G4-7U 3.6
M9579 5KS286XAA114 510 $3,073 G4-7UX1 3.20 M9781 5KS365SAA204 1080 $6,977 G4-7U 3.6
M9580 5KS286XAA204 510 $2,922 G4-7UX1 3.20 M9782 5KS445SAA408 2020 $19,025 G4-7U 3.6
M9581 5KS326XAA304 730 $4,962 G4-7UX1 3.20 M9784 5KS447SAA408 2580 $21,185 G4-7U 3.6
M9582 5KS364XAA404 1010 $8,073 G4-7UX 3.20 M9785 5KS449SAA408 3150 $23,102 G4-7U 3.7
M9583 5KS324XAA114 670 $4,176 G4-7UX1 3.20 M9820 5KS324SAA108 670 $3,301 G4-7U1 3.5
M9584 5KS324XAA204 710 $4,051 G4-7UX1 3.20 M9823 5KS326SAA108 700 $4,223 G4-7U1 3.5
M9585 5KS364XAA304 1030 $6,633 G4-7UX 3.20 M9828 5KS286SAA114 510 $2,653 G4-7U1 3.5
M9586 5KS365XAA404 1090 $9,958 G4-7UX 3.20 M9829 5KS324SAA114 670 $3,301 G4-7U1 3.5
M9587 5KS326XAA114 700 $5,098 G4-7UX1 3.20 M9830 5KS365SAA114 970 $7,215 G4-7U 3.6
M9588 5KS326XAA204 740 $4,615 G4-7UX1 3.20 M9831 5KS405SAA114 1530 $9,342 G4-7U 3.6
M9589 5KS365XAA304 1070 $7,562 G4-7UX 3.20 M9832 5KS444SAA204 1970 $11,337 G4-7U 3.6
M9590 5KS404XAA404 1490 $12,015 G4-7UX 3.20 M9834 5KS326SAA304 730 $4,184 G4-7U1 3.5
M9591 5KS364XAA114 940 $6,837 G4-7UX 3.20 M9835 5KS364SAA304 1030 $5,771 G4-7U 3.5
M9592 5KS364XAA204 1020 $6,616 G4-7UX 3.20 M9837 5KS404SAA304 1480 $7,794 G4-7U 3.6
M9593 5KS404XAA304 1480 $8,830 G4-7UX 3.20 M9838 5KS284SAA114 460 $2,256 G4-7U1 3.4
M9594 5KS405XAA404 1570 $13,560 G4-7UX 3.20 M9839 5KS326SAA114 700 $4,223 G4-7U1 3.5
M9596 5KS365XAA204 1090 $7,839 G4-7UX 3.20 M9845 5KS449SAA328 3070 $19,053 G4-7U 3.7
M9597 5KS405XAA304 1540 $9,698 G4-7UX 3.20 M9846 5KS444SAA304 2060 $11,669 G4-7U 3.6
M9598 5KS444XAA404 1950 $16,966 G4-7UX 3.20 M9847 5KS364SAA114 940 $5,877 G4-7U 3.6
M9693 5KS405XAA204 1480 $9,651 G4-7UX 3.21 M9851 5KS449SAA204 2790 $19,347 G4-7U 3.7
M9695 5KS445XAA404 2020 $21,498 G4-7UX 3.21 M9854 5KS445SAA204 2060 $13,190 G4-7U 3.7
M9697 5KS444XAA204 1970 $12,434 G4-7UX 3.21 M9868 5KS405SAA304 1540 $8,664 G4-7U 3.6

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.11
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
M9869 5KS447SAA304 2860 $17,030 G4-7U 3.7 M9955 5KS256SAA100 350 $1,905 G4-7U1 3.8
M9870 5KS445SAA304 2130 $14,057 G4-7U 3.6 M9956 5KS256SAA300 350 $2,002 G4-7U1 3.8

Cross Reference Guide

M9871 5KS182SAA405 76 $819 G4-7U1 3.2 M9958 5KS447SAA208 2610 $16,545 G4-7U 3.7
M9872 5KS182SAA404 76 $819 G4-7U1 3.2 M9959 5KS447SAA204 2610 $16,545 G4-7U 3.7
M9873 5KS184SAA405 101 $967 G4-7U1 3.2 M9961 5KS447SAA118 2560 $18,577 G4-7U 3.7
M9874 5KS184SAA404 101 $967 G4-7U1 3.2 M9988 5KS449SAA201 3010 $19,347 G4-7U 3.7
M9875 5KS213SAA405 200 $1,155 G4-7U1 3.2 M9989 5KS449SAA202 3010 $19,347 G4-7U 3.7
M9876 5KS213SAA404 200 $1,155 G4-7U1 3.2 M9990 5KS449SAA212 2980 $22,654 G4-7U 3.7
M9877 5KS215SAA405 220 $1,443 G4-7U1 3.3 M9991 5KS447SAA201 2610 $16,545 G4-7U 3.7
M9878 5KS215SAA404 220 $1,443 G4-7U1 3.3 M9992 5KS405SAA140 1530 $9,342 64-7U 3.6
M9879 5KS254SAA405 315 $1,917 G4-7U1 3.3 M9993 5KS444SAA150 1790 $12,203 64-7U 3.6
M9880 5KS254SAA404 315 $1,917 G4-7U1 3.3 M9994 5KS445SAA149 1860 $14,674 64-7U 3.7
M9881 5KS256SAA405 350 $2,423 G4-7U1 3.3 M9995 5KS447SAA125 2560 $18,577 64-7U 3.7
M9882 5KS256SAA404 350 $2,423 G4-7U1 3.3 M9996 5KS449SAA146 2770 $23,935 G4-7U 3.7
M9883 5KS284SAA405 460 $2,828 G4-7U1 3.4 P100 Refer to factory 7500 $100,211 G8-9PWII 5.3
M9884 5KS284SAA404 460 $2,828 G4-7U1 3.4 P101 Refer to factory 7500 $90,103 G8-9PWII 5.3
M9885 5KS286SAA405 510 $3,684 G4-7U1 3.4 P102 Refer to factory 7000 $118,501 G8-9PWII 5.3
M9886 5KS286SAA404 510 $3,684 G4-7U1 3.4 P103 Refer to factory 7000 $108,393 G8-9PWII 5.3
M9887 5KS182SAA408 76 $819 G4-7U1 3.2 P104 Refer to factory 7500 $103,933 G8-9PWII 5.3
M9888 5KS184SAA408 101 $967 G4-7U1 3.2 P105 Refer to factory 7500 $93,825 G8-9PWII 5.3
M9889 5KS182SAA207 76 $663 G4-7U1 3.8 P106 Refer to factory 8500 $109,523 G8-9PWII 5.3
M9890 5KS184SAA202 101 $764 G4-7U1 3.8 P107 Refer to factory 7500 $108,588 G8-9PWII 5.3
M9891 5KS213SAA200 200 $1,004 G4-7U1 3.8 P108 Refer to factory 7500 $98,482 G8-9PWII 5.3
M9892 5KS215SAA203 220 $1,111 G4-7U1 3.8 P109 Refer to factory 8500 $112,912 G8-9PWII 5.3
M9893 5KS254SAA200 315 $1,522 G4-7U1 3.8 P110 Refer to factory 9200 $116,039 G8-9PWII 5.3
M9894 5KS256SAA200 350 $1,798 G4-7U1 3.8 P111 Refer to factory 9200 $105,932 G8-9PWII 5.3
M9895 5KS284SAA200 460 $2,309 G4-7U1 3.8 P112 Refer to factory 8500 $118,563 G8-9PWII 5.3
M9896 5KS286SAA200 510 $2,671 G4-7U1 3.8 P113 Refer to factory 9200 $125,351 G8-9PWII 5.3
M9901 5KS284SAA300 460 $2,672 G4-7U1 3.8 P114 Refer to factory 9200 $115,245 G8-9PWII 5.3
M9902 5KS286SAA300 510 $3,230 G4-7U1 3.8 P115 Refer to factory 9300 $155,397 G8-9PWII 5.3
M9903 5KS284SAA100 460 $2,403 G4-7U1 3.8 P116 Refer to factory 12000 $136,806 G8-9PWII 5.3
M9904 5KS286SAA100 510 $2,800 G4-7U1 3.8 P117 Refer to factory 12000 $124,678 G8-9PWII 5.3
M9906 5KS449SAA209 2980 $22,654 G4-7U 3.7 P118 Refer to factory 9300 $161,378 G8-9PWII 5.3
M9911 5KS213SAA208 200 $924 G4-7U1 3.3 P119 Refer to factory 12000 $143,638 G8-9PWII 5.3
M9912 5KS215SAA208 220 $1,031 G4-7U1 3.4 P120 Refer to factory 12000 $131,509 G8-9PWII 5.3
M9913 5KS254SAA208 315 $1,418 G4-7U1 3.4 P121 Refer to factory 9300 $170,017 G8-9PWII 5.3
M9914 5KS256SAA208 350 $1,694 G4-7U1 3.4 P122 Refer to factory 16000 $170,425 G8-9PWII 5.3
M9915 5KS324SAA208 710 $3,272 G4-7U1 3.5 P123 Refer to factory 16000 $157,398 G8-9PWII 5.3
M9916 5KS324SAA218 710 $3,272 G4-7U1 3.5 P124 Refer to factory 13900 $203,839 G8-9PWII 5.3
M9917 5KS326SAA208 740 $3,836 G4-7U1 3.5 P125 Refer to factory 16000 $171,892 G8-9PWII 5.3
M9918 5KS326SAA218 740 $3,836 G4-7U1 3.5 P126 Refer to factory 16000 $158,866 G8-9PWII 5.3
M9919 5KS364SAA208 1020 $5,755 G4-7U 3.6 P127 Refer to factory 16000 $177,764 G8-9PWII 5.3
M9921 5KS364SAA218 1020 $5,755 G4-7U 3.6 P128 Refer to factory 16000 $164,738 G8-9PWII 5.3
M9922 5KS365SAA208 1080 $6,977 G4-7U 3.6 P129 Refer to factory 13900 $209,516 G8-9PWII 5.3
M9923 5KS365SAA218 1080 $6,977 G4-7U 3.6 P130 Refer to factory 16000 $186,572 G8-9PWII 5.3
M9924 5KS405SAA208 1480 $8,617 G4-7U 3.6 P131 Refer to factory 16000 $173,545 G8-9PWII 5.3
M9925 5KS405SAA218 1480 $8,617 G4-7U 3.6 P132 Refer to factory 13900 $220,871 G8-9PWII 5.3
M9926 5KS444SAA208 1970 $11,337 G4-7U 3.6 P133 Refer to factory 16000 $196,847 G8-9PWII 5.3
M9927 5KS444SAA218 1970 $11,337 G4-7U 3.6 P134 Refer to factory 16000 $183,821 G8-9PWII 5.3
M9928 5KS445SAA208 2090 $13,190 G4-7U 3.7 P135 Refer to factory 13900 $228,439 G8-9PWII 5.3
M9929 5KS445SAA218 2090 $13,190 G4-7U 3.7 P200 Refer to factory 8100 $139,035 G8-9PTAC 5.5
M9933 5KS449SAA208 2790 $19,347 G4-7U 3.7 P201 Refer to factory 8100 $128,927 G8-9PTAC 5.5
M9935 5KS284SAA208 460 $2,162 G4-7U1 3.4 P202 Refer to factory 8100 $140,136 G8-9PTAC 5.5
M9937 5KS286SAA208 510 $2,525 G4-7U1 3.5 P203 Refer to factory 8100 $130,030 G8-9PTAC 5.5
M9939 5KS182SAA108 76 $600 G4-7U1 3.3 P204 Refer to factory 7000 $120,897 G8-9PTAC 5.5
M9940 5KS184SAA108 101 $712 G4-7U1 3.3 P205 Refer to factory 7000 $110,791 G8-9PTAC 5.5
M9941 5KS182SAA208 76 $583 G4-7U1 3.3 P206 Refer to factory 8100 $141,240 G8-9PTAC 5.5
M9942 5KS184SAA208 101 $684 G4-7U1 3.3 P207 Refer to factory 8100 $131,134 G8-9PTAC 5.5
M9943 5KS182SAA308 76 $604 G4-7U1 3.2 P208 Refer to factory 8750 $122,740 G8-9PTAC 5.5
M9944 5KS184SAA308 101 $675 G4-7U1 3.2 P209 Refer to factory 8750 $112,634 G8-9PTAC 5.5
M9945 5KS182SAA100 76 $680 G4-7U1 3.8 P210 Refer to factory 8100 $141,240 G8-9PTAC 5.5
M9946 5KS182SAA300 76 $684 G4-7U1 3.8 P211 Refer to factory 8100 $131,134 G8-9PTAC 5.5
M9947 5KS184SAA100 101 $792 G4-7U1 3.8 P212 Refer to factory 8750 $124,123 G8-9PTAC 5.5
M9948 5KS184SAA300 101 $755 G4-7U1 3.8 P213 Refer to factory 8750 $114,017 G8-9PTAC 5.5
M9949 5KS213SAA101 200 $1,010 G4-7U1 3.8 P214 Refer to factory 9950 $156,830 G8-9PTAC 5.5
M9950 5KS213SAA300 200 $900 G4-7U1 3.8 P215 Refer to factory 8750 $141,244 G8-9PTAC 5.5
M9951 5KS215SAA100 220 $1,170 G4-7U1 3.8 P216 Refer to factory 8750 $129,520 G8-9PTAC 5.5
M9952 5KS215SAA300 220 $1,245 G4-7U1 3.8 P217 Refer to factory 9950 $175,454 G8-9PTAC 5.5
M9953 5KS254SAA100 315 $1,905 G4-7U1 3.8 P218 Refer to factory 10500 $144,827 G8-9PTAC 5.5
M9954 5KS254SAA300 315 $1,651 G4-7U1 3.8 P219 Refer to factory 10500 $133,103 G8-9PTAC 5.5

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.12 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
P220 Refer to factory 9950 $190,720 G8-9PTAC 5.5 S234 5KE213BC305 139 $497 G4-7TEZ 1.8
P221 Refer to factory 10500 $156,772 G8-9PTAC 5.5 S235 5KE215BC104 183 $677 G4-7TEZ 1.9
Cross Reference Guide

P222 Refer to factory 10500 $145,046 G8-9PTAC 5.5 S236 5KE215BC105 183 $677 G4-7TEZ 1.9
P223 Refer to factory 11500 $205,985 G8-9PTAC 5.5 S237 5KE215BC204 189 $630 G4-7TEZ 1.9
P224 Refer to factory 10500 $167,515 G8-9PTAC 5.5 S238 5KE215BC205 189 $630 G4-7TEZ 1.9
P225 Refer to factory 10500 $155,792 G8-9PTAC 5.5 S239 5KE215BC206 189 $630 G4-7TEZ 1.9
P226 Refer to factory 11500 $174,407 G8-9PTAC 5.5 S240 5KE215BC304 165 $716 G4-7TEZ 1.8
P227 Refer to factory 13500 $208,756 G8-9PTAC 5.5 S241 5KE215BC305 165 $716 G4-7TEZ 1.8
P228 Refer to factory 13500 $197,032 G8-9PTAC 5.5 S242 5KE254BC104 282 $888 G4-7TEZ 1.9
P229 Refer to factory 12500 $178,023 G8-9PTAC 5.5 S243 5KE254BC105 282 $888 G4-7TEZ 1.9
P230 Refer to factory 17500 $221,521 G8-9PTAC 5.5 S244 5KE254BC204 288 $908 G4-7TEZ 1.9
P231 Refer to factory 17500 $209,797 G8-9PTAC 5.5 S245 5KE254BC205 288 $881 G4-7TEZ 1.9
P232 Refer to factory 13500 $218,111 G8-9PTAC 5.5 S246 5KE254BC206 288 $881 G4-7TEZ 1.9
P233 Refer to factory 17500 $179,625 G8-9PTAC 5.5 S247 5KE254BC304 257 $945 G4-7TEZ 1.9
P234 Refer to factory 17500 $166,596 G8-9PTAC 5.5 S248 5KE254BC305 257 $945 G4-7TEZ 1.9
P235 Refer to factory 13500 $226,383 G8-9PTAC 5.5 S249 5KE256BC104 315 $1,136 G4-7TEZ 1.9
P236 Refer to factory 17500 $186,974 G8-9PTAC 5.5 S250 5KE256BC105 315 $1,136 G4-7TEZ 1.9
P237 Refer to factory 17500 $173,947 G8-9PTAC 5.5 S251 5KE256BC204 332 $1,176 G4-7TEZ 1.9
P238 Refer to factory 17500 $194,323 G8-9PTAC 5.5 S252 5KE256BC205 332 $1,141 G4-7TEZ 1.9
P239 Refer to factory 17500 $181,296 G8-9PTAC 5.5 S253 5KE256BC206 332 $1,141 G4-7TEZ 1.9
P240 Refer to factory 14000 $229,691 G8-9PTAC 5.5 S254 5KE256BC304 295 $1,174 G4-7TEZ 1.9
P241 Refer to factory 17500 $201,674 G8-9PTAC 5.5 S255 5KE256BC305 295 $1,174 G4-7TEZ 1.9
P242 Refer to factory 17500 $188,647 G8-9PTAC 5.5 S256 5KE284BC115 418 $1,432 G4-7TEZ 1.10
PB14A 4001A5202AAG001 $72 G4-7KITS 3.33 S257 5KE284BC204 429 $1,366 G4-7TEZ 1.10
PB18A 4001A5202AAG002 $98 G4-7KITS 3.33 S258 5KE284BC205 429 $1,366 G4-7TEZ 1.10
PB21A 4001A5202AAG003 $125 G4-7KITS 3.33 S259 5KE284BC206 429 $1,366 G4-7TEZ 1.10
PB25A 4001A5202AAG004 $169 G4-7KITS 3.33 S260 5KE284BC304 414 $1,594 G4-7TEZ 1.9
PB28A 4001A5202AAG005 $224 G4-7KITS 3.33 S261 5KE284BC305 414 $1,594 G4-7TEZ 1.9
Q100 Refer to factory 9700 $156,830 G8-9QT 5.4 S262 5KE286BC115 455 $1,666 G4-7TEZ 1.10
Q101 Refer to factory 9500 $141,244 G8-9QT 5.4 S263 5KE286BC116 455 $1,666 G4-7TEZ 1.10
Q102 Refer to factory 9500 $129,520 G8-9QT 5.4 S264 5KE286BC204 475 $1,547 G4-7TEZ 1.10
Q103 Refer to factory 11400 $175,454 G8-9QT 5.4 S265 5KE286BC205 475 $1,547 G4-7TEZ 1.10
Q104 Refer to factory 10100 $144,827 G8-9QT 5.4 S266 5KE286BC206 475 $1,547 G4-7TEZ 1.10
Q105 Refer to factory 10100 $133,103 G8-9QT 5.4 S267 5KE286BC305 473 $1,881 G4-7TEZ 1.9
Q106 Refer to factory 12500 $190,720 G8-9QT 5.4 S268 5KE145FC202 57 $405 G4-7TECZ 1.12
Q107 Refer to factory 11000 $156,772 G8-9QT 5.4 S269 5KE145FC205 57 $425 G4-7TECZ 1.12
Q108 Refer to factory 11000 $145,046 G8-9QT 5.4 S270 5KE182FC205 95 $479 G4-7TECZ 1.12
Q109 Refer to factory 13000 $204,474 G8-9QT 5.4 S271 5KE184FC205 114 $539 G4-7TECZ 1.12
Q110 Refer to factory 12100 $165,882 G8-9QT 5.4 S272 5KE213FC205 167 $684 G4-7TECZ 1.12
Q111 Refer to factory 12100 $153,754 G8-9QT 5.4 S273 5KE215FC205 189 $804 G4-7TECZ 1.12
Q112 Refer to factory 13600 $205,985 G8-9QT 5.4 S274 5KE254FC205 288 $1,127 G4-7TECZ 1.12
Q113 Refer to factory 12700 $167,515 G8-9QT 5.4 S275 5KE256FC205 332 $1,395 G4-7TECZ 1.12
Q114 Refer to factory 12700 $155,792 G8-9QT 5.4 S276 5KE284FC205 429 $1,703 G4-7TECZ 1.13
Q115 Refer to factory 14100 $208,756 G8-9QT 5.4 S277 5KE286FC205 475 $1,960 G4-7TECZ 1.13
Q116 Refer to factory 14100 $197,032 G8-9QT 5.4 S278 5KE324BFC315 625 $2,312 G4-7TEZ 1.10
Q117 Refer to factory 15000 $221,521 G8-9QT 5.4 S279 5KE324BFC305 626 $2,312 G4-7TEZ 1.10
Q118 Refer to factory 15000 $209,797 G8-9QT 5.4 S280 5KE326BFC305 763 $2,709 G4-7TEZ 1.10
S209 5KE143FC205 53 $385 G4-7TECZ 1.12 S281 5KE324BFC115 788 $2,144 G4-7TEZ 1.10
S210 5KE143BC105 53 $282 G4-7TEZ 1.8 S282 5KE324BFC105 788 $2,144 G4-7TEZ 1.10
S211 5KE143BC205 53 $243 G4-7TEZ 1.8 S283 5KE324BFC205 776 $2,053 G4-7TEZ 1.10
S212 5KE143BC305 55 $315 G4-7TEZ 1.8 S284 5KE324BFC204 776 $2,053 G4-7TEZ 1.10
S213 5KE145BC105 57 $321 G4-7TEZ 1.8 S285 5KE364BFC305 932 $3,719 G4-7TEZ 1.10
S214 5KE145BC202 57 $262 G4-7TEZ 1.8 S286 5KE326BFC115 788 $2,774 G4-7TEZ 1.10
S215 5KE145BC205 57 $282 G4-7TEZ 1.8 S287 5KE326BFC105 788 $2,774 G4-7TEZ 1.10
S216 5KE145BC305 59 $315 G4-7TEZ 1.8 S288 5KE326BFC215 803 $2,521 G4-7TEZ 1.10
S217 5KE182BC204 95 $320 G4-7TEZ 1.8 S289 5KE326BFC205 803 $2,521 G4-7TEZ 1.10
S218 5KE182BC206 95 $320 G4-7TEZ 1.8 S290 5KE326BFC204 803 $2,521 G4-7TEZ 1.10
S219 5KE182BC205 95 $320 G4-7TEZ 1.8 S291 5KE365BFC305 933 $4,337 G4-7TEZ 1.10
S220 5KE182BC305 90 $339 G4-7TEZ 1.8 S292 5KE364BFC115 935 $3,751 G4-7TEZ 1.10
S221 5KE182BC105 90 $357 G4-7TEZ 1.8 S293 5KE364BFC215 928 $3,617 G4-7TEZ 1.10
S222 5KE184BC104 106 $442 G4-7TEZ 1.8 S295 5KE364BFC205 932 $3,617 G4-7TEZ 1.10
S223 5KE184BC204 114 $380 G4-7TEZ 1.8 S296 5KE364BFC204 932 $3,617 G4-7TEZ 1.10
S224 5KE184BC206 114 $380 G4-7TEZ 1.8 S297 5KE365BFC115 992 $4,581 G4-7TEZ 1.10
S225 5KE184BC205 115 $380 G4-7TEZ 1.8 S298 5KE365BFC205 1001 $4,584 G4-7TEZ 1.10
S226 5KE184BC305 101 $375 G4-7TEZ 1.8 S299 5KE365BFC204 1001 $4,584 G4-7TEZ 1.10
S227 5KE184BC105 106 $442 G4-7TEZ 1.8 S2053 5KAF143SAA2151 43 $724 G4-7AS 4.2
S228 5KE213BC104 156 $576 G4-7TEZ 1.9 S2054 5KAF145SAA2151 43 $780 G4-7AS 4.2
S229 5KE213BC105 156 $576 G4-7TEZ 1.9 S2055 5KAF182SAA2151 76 $980 G4-7AS 4.2
S230 5KE213BC204 167 $510 G4-7TEZ 1.9 S2056 5KAF184SAA2151 101 $1,095 G4-7AS 4.2
S231 5KE213BC205 167 $510 G4-7TEZ 1.9 S2057 5KAF213SAA2151 200 $1,281 G4-7AS 4.2
S232 5KE213BC206 167 $510 G4-7TEZ 1.9 S2058 5KAF215SAA2151 220 $1,531 G4-7AS 4.2
S233 5KE213BC304 139 $497 G4-7TEZ 1.8 S2059 5KAF254SAA2151 315 $1,844 G4-7AS 4.2

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.13
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
S2060 5KAF256SAA2151 350 $2,040 G4-7AS 4.2 S2524 5KE215AC104 180 $806 G4-7DEZ 1.3
S2061 5KAF284SAA2151 460 $2,548 G4-7AS 4.2 S2525 5KE215AC205 180 $590 G4-7DEZ 1.2

Cross Reference Guide

S2062 5KAF286SAA2151 510 $2,913 G4-7AS 4.2 S2526 5KE215AC204 180 $590 G4-7DEZ 1.2
S2063 5KAF324SS2150D20P 690 $3,772 G4-7AS 4.2 S2527 5KE215AC206 180 $590 G4-7DEZ 1.2
S2064 5KAF326SS2150D20P 740 $4,666 G4-7AS 4.2 S2528 5KE256AC305 260 $945 G4-7DEZ 1.2
S2065 5KAF364SS2150D20P 1040 $6,014 G4-7AS 4.2 S2529 5KE256AC304 260 $945 GO-7DEZ 1.2
S2066 5KAF365SS2150D20P 1070 $6,813 G4-7AS 4.2 S2530 5KE254AC105 233 $971 G4-7DEZ 1.3
S2067 5KAF405SS2150P 1560 $9,219 G4-7AS 4.2 S2531 5KE254AC104 233 $970 G4-7DEZ 1.3
S2068 5KAF444SS2150P 2050 $11,988 G4-7AS 4.2 S2532 5KE254AC205 246 $815 G4-7DEZ 1.3
S2069 5KAF445SS2150P 2050 $13,863 G4-7AS 4.2 S2533 5KE254AC204 246 $815 G4-7DEZ 1.3
S2070 5KAF445SS2151P 2050 $16,764 G4-7AS 4.2 S2534 5KE254AC206 246 $815 G4-7DEZ 1.3
S2071 5KAF449SS2150P 2830 $20,917 G4-7AS 4.2 S2535 5KE284AC305 343 $1,285 GO-7DEZ 1.3
S2072 5KAF449SSH2150P 3110 $23,837 G4-7AS 4.2 S2536 5KE284AC304 343 $1,285 GO-7DEZ 1.3
S2073 5KAF364SS2019D20P 1060 $6,600 G4-7AS 4.2 S2537 5KE256AC105 282 $1,186 G4-7DEZ 1.3
S2074 5KAF365SS2044D20P 1070 $7,890 G4-7AS 4.2 S2538 5KE256AC104 282 $1,185 G4-7DEZ 1.3
S2075 5KAF405SS2038P 1560 $11,014 G4-7AS 4.2 S2539 5KE256AC205 277 $1,033 G4-7DEZ 1.3
S2076 5KAF405SS2039P 1560 $13,890 G4-7AS 4.2 S2540 5KE256AC204 277 $1,033 G4-7DEZ 1.3
S2077 5KAF445SS2033P 2050 $15,765 G4-7AS 4.2 S2541 5KE256AC206 277 $1,033 G4-7DEZ 1.3
S2078 5KAF445SS2034P 2050 $18,666 G4-7AS 4.2 S2542 5KE286AC305 392 $1,625 GO-7DEZ 1.3
S2079 5KAF449SS2028P 2870 $23,417 G4-7AS 4.2 S2543 5KE284AC115 370 $1,396 GO-7DEZ 1.3
S2080 5KAF449SS2029P 2890 $26,337 G4-7AS 4.2 S2544 5KE284AC205 352 $1,155 G4-7DEZ 1.3
S2174 5KE405SS304 1450 $6,496 G6-7SE 8.14 S2545 5KE284AC204 352 $1,155 G4-7DEZ 1.3
S2210 5KE143KC105 53 $328 G4-7TECZ 1.12 S2547 5KE286AC115 440 $1,791 G4-7DEZ 1.3
S2211 5KE143KC205 53 $288 G4-7TECZ 1.12 S2549 5KE286AC205 407 $1,325 G4-7DEZ 1.3
S2213 5KE145KC105 62 $368 G4-7TECZ 1.12 S2550 5KE286AC204 407 $1,325 G4-7DEZ 1.3
S2214 5KE145KC202 62 $308 G4-7TECZ 1.12 S2552 5KE182AC104 88 $402 G4-7DEZ 1.2
S2215 5KE145KC205 62 $328 G4-7TECZ 1.12 S2601 5KE182CC305 97 $672 G5-7XPZ 1.18
S2216 5KE145KC305 62 $378 G4-7TECZ 1.12 S2603 5KE184CC305 112 $725 G5-7XPZ 1.18
S2219 5KE182KC205 95 $376 G4-7TECZ 1.12 S2605 5KE182CC105 101 $686 G5-7XPZ 1.18
S2221 5KE182KC105 95 $413 G4-7TECZ 1.12 S2606 5KE182CC205 106 $657 G5-7XPZ 1.18
S2225 5KE184KC205 114 $436 G4-7TECZ 1.12 S2608 5KE213CC305 185 $856 G5-7XPZ 1.18
S2227 5KE184KC105 106 $498 G4-7TECZ 1.12 S2610 5KE184CC105 121 $797 G5-7XPZ 1.18
S2229 5KE213KC105 156 $643 G4-7TECZ 1.12 S2611 5KE184CC205 123 $732 G5-7XPZ 1.18
S2231 5KE213KC205 167 $577 G4-7TECZ 1.12 S2613 5KE215CC305 216 $1,110 G5-7XPZ 1.18
S2236 5KE215KC105 183 $744 G4-7TECZ 1.12 S2615 5KE213CC105 189 $937 G5-7XPZ 1.18
S2238 5KE215KC205 189 $697 G4-7TECZ 1.12 S2616 5KE213CC205 187 $932 G5-7XPZ 1.18
S2243 5KE254KC105 282 $1,016 G4-7TECZ 1.12 S2618 5KE254CC305 308 $1,501 G5-7XPZ 1.18
S2245 5KE254KC205 288 $1,009 G4-7TECZ 1.12 S2620 5KE215CC105 213 $1,096 G5-7XPZ 1.18
S2250 5KE256KC105 315 $1,272 G4-7TECZ 1.12 S2621 5KE215CC205 216 $1,076 G5-7XPZ 1.18
S2252 5KE256KC205 332 $1,277 G4-7TECZ 1.12 S2623 5KE256CC305 359 $1,760 G5-7XPZ 1.18
S2256 5KE284KC115 418 $1,593 G4-7TECZ 1.13 S2625 5KE254CC105 330 $1,466 G5-7XPZ 1.18
S2258 5KE284KC205 429 $1,570 G4-7TECZ 1.13 S2626 5KE254CC205 339 $1,446 G5-7XPZ 1.18
S2262 5KE286KC115 455 $1,863 G4-7TECZ 1.13 S2628 5KE284CC305 436 $2,345 G5-7XPZ 1.18
S2265 5KE286KC205 475 $1,827 G4-7TECZ 1.13 S2630 5KE256CC105 367 $1,735 G5-7XPZ 1.18
S2333 5KE405SS308 1450 $6,496 G6-7SE 8.14 S2631 5KE256CC205 386 $1,719 G5-7XPZ 1.18
S2340 5KE324KFC205 803 $2,329 G4-7TECZ 1.13 S2633 5KE286CC305 517 $2,758 G5-7XPZ 1.18
S2341 5KE326KFC205 812 $2,849 G4-7TECZ 1.13 S2635 5KE284CC115 464 $2,182 G5-7XPZ 1.18
S2342 5KE364KFC205 959 $4,261 G4-7TECZ 1.13 S2636 5KE284CC205 488 $2,104 G5-7XPZ 1.18
S2343 5KE365KFC205 1019 $5,362 G4-7TECZ 1.13 S2638 5KE324CC305 682 $3,502 G5-7XPZ 1.18
S2501 5KE182AC305 88 $315 G4-7DEZ 1.2 S2640 5KE286CC115 502 $2,471 G5-7XPZ 1.18
S2502 5KE184AC305 97 $332 G4-7DEZ 1.2 S2641 5KE286CC205 570 $2,372 G5-7XPZ 1.18
S2503 5KE182AC105 88 $403 G4-7DEZ 1.2 S2643 5KE326CC305 744 $3,925 G5-7XPZ 1.18
S2504 5KE182AC205 81 $288 G4-7DEZ 1.2 S2644 5KE324CC115 691 $3,360 G5-7XPZ 1.18
S2505 5KE182AC204 81 $287 G4-7DEZ 1.2 S2645 5KE324CC205 717 $3,256 G5-7XPZ 1.18
S2506 5KE182AC206 81 $287 G4-7DEZ 1.2 S2647 5KE364CC305 871 $5,191 G5-7XPZ 1.18
S2507 5KE213AC305 132 $450 G4-7DEZ 1.2 S2648 5KE326CC115 770 $4,148 G5-7XPZ 1.18
S2508 5KE213AC304 132 $450 G4-7DEZ 1.2 S2649 5KE326CC205 783 $3,836 G5-7XPZ 1.18
S2509 5KE184AC105 101 $480 G4-7DEZ 1.2 S2651 5KE365CC305 928 $5,836 G5-7XPZ 1.18
S2510 5KE184AC104 101 $480 G4-7DEZ 1.2 S2653 5KE364CC115 816 $5,357 G5-7XPZ 1.18
S2511 5KE184AC205 99 $348 G4-7DEZ 1.2 S2654 5KE364CC205 911 $5,318 G5-7XPZ 1.18
S2512 5KE184AC204 99 $348 G4-7DEZ 1.2 S2656 5KE365CC115 997 $5,612 G5-7XPZ 1.18
S2513 5KE184AC206 99 $348 G4-7DEZ 1.2 S2657 5KE365CC205 997 $6,516 G5-7XPZ 1.18
S2514 5KE215AC305 158 $620 G4-7DEZ 1.2 S2790 5KE143BC204 53 $250 GO-7TEZ 1.8
S2515 5KE215AC304 158 $620 G4-7DEZ 1.2 S2791 5KE145BC204 57 $200 G4-7TEZ 1.8
S2516 5KE213AC105 156 $630 G4-7DEZ 1.2 S2792 5KE182BC104 90 $357 GO-7TEZ 1.8
S2517 5KE213AC104 156 $630 G4-7DEZ 1.2 S2793 5KE145BC207 57 $290 G4-7TEZ 1.8
S2518 5KE213AC205 152 $475 G4-7DEZ 1.2 S2801 5KE143AC204 49 $220 GO-7DEZ 1.2
S2519 5KE213AC204 152 $475 G4-7DEZ 1.2 S2802 5KE143AC205 49 $220 G4-7DEZ 1.2
S2520 5KE213AC206 152 $475 G4-7DEZ 1.2 S2803 5KE145AC104 62 $332 G4-7DEZ 1.2
S2521 5KE254AC305 211 $790 G4-7DEZ 1.2 S2804 5KE145AC105 62 $332 GO-7DEZ 1.2
S2522 5KE254AC304 211 $790 G4-7DEZ 1.2 S2805 5KE145AC201 57 $245 GO-7DEZ 1.2
S2523 5KE215AC105 180 $807 G4-7DEZ 1.3 S2806 5KE145AC202 57 $245 G4-7DEZ 1.2

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.14 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
S2807 5KE145AC204 59 $260 GO-7DEZ 1.2 S3539 5KE445AC308 1276 $7,815 G4-7DEZ 1.5
S2808 5KE145AC205 59 $260 G4-7DEZ 1.2 S3540 5KE405AC114 1005 $7,600 G4-7DEZ 1.5
Cross Reference Guide

S2941 5KE324KFC115 802 $2,632 G4-7TEZ 6.16 S3541 5KE405AC118 1005 $7,600 G4-7DEZ 1.5
S2942 5KE326KFC115 835 $3,059 G4-7TEZ 6.16 S3542 5KE444AC204 1320 $7,485 G4-7DEZ 1.5
S2943 5KE364KFC115 955 $4,608 G4-7TEZ 6.16 S3543 5KE444AC208 1320 $7,485 G4-7DEZ 1.5
S2944 5KE365KFC115 1012 $5,511 G4-7TEZ 6.16 S3544 5KE445AC320 1364 $9,145 G4-7DEZ 1.5
S2945 5KE405KFC115 1259 $7,128 G4-7TEZ 6.16 S3545 5KE445AC321 1364 $9,145 G4-7DEZ 1.5
S2946 5KE444KFC118 1623 $9,327 G4-7TEZ 6.16 S3546 5KE444AC114 1150 $11,485 G4-7DEZ 1.5
S2947 5KE445KFC118 1722 $12,063 G4-7TEZ 6.16 S3547 5KE444AC118 1150 $11,485 G4-7DEZ 1.5
S2948 5KE182KC107 98 $481 G4-7TEZ 6.16 S3548 5KE445AC204 1430 $10,094 G4-7DEZ 1.5
S2949 5KE184KC107 106 $595 G4-7TEZ 6.16 S3549 5KE445AC208 1430 $10,095 G4-7DEZ 1.5
S2950 5KE213KC107 156 $743 G4-7TEZ 6.16 S3550 5KE447AC320 1810 $14,550 G4-7DEZ 1.5
S2951 5KE215KC107 183 $878 G4-7TEZ 6.16 S3551 5KE447AC321 1810 $14,550 G4-7DEZ 1.5
S2952 5KE254KC107 282 $1,132 G4-7TEZ 6.16 S3552 5KE445AC114 1276 $14,244 G4-7DEZ 1.5
S2953 5KE256KC107 315 $1,473 G4-7TEZ 6.16 S3553 5KE445AC118 1276 $14,225 G4-7DEZ 1.5
S2954 5KE284KC117 418 $2,114 G4-7TEZ 6.16 S3554 5KE447AC204 1760 $12,150 G4-7DEZ 1.5
S2955 5KE286KC117 455 $2,257 G4-7TEZ 6.16 S3555 5KE447AC208 1760 $12,150 G4-7DEZ 1.5
S3402 5K509EN1304MRA3 3620 $29,811 G6-7DAN 5.2 S3556 5KE449AC320 2160 $16,500 G4-7DEZ 1.5
S3403 5K509EN2771MRA2 3620 $28,657 G6-7DAN 5.2 S3557 5KE449AC321 2160 $16,500 G4-7DEZ 1.5
S3404 5K509EN1304MRA2 3620 $31,489 G6-7DAN 5.2 S3558 5KE445AC120 1320 $17,363 G4-7DEZ 1.5
S3405 5K509EN2771MRA1 3620 $29,809 G6-7DAN 5.2 S3559 5KE445AC121 1320 $17,363 G4-7DEZ 1.5
S3406 5K509EN1304MRA1 3620 $33,137 G6-7DAN 5.2 S3560 5KE449AC204 1870 $15,985 G4-7DEZ 1.5
S3407 5K509EN2771M 3620 $30,880 G6-7DAN 5.2 S3561 5KE449AC208 1870 $15,985 G4-7DEZ 1.5
S3408 5K511EN2307MRA2 4710 $31,883 G6-7DAN 5.2 S3562 5KE447AC120 1590 $19,850 G4-7DEZ 1.5
S3409 5K509EN1304M 3620 $36,346 G6-7DAN 5.2 S3563 5KE447AC121 1590 $19,850 G4-7DEZ 1.5
S3411 5K511EN2307MRA1 4710 $33,932 G6-7DAN 5.2 S3564 5KE449AC120 1760 $20,280 G4-7DEZ 1.5
S3413 5K511EN2307M 4710 $35,805 G6-7DAN 5.2 S3565 5KE449AC121 1760 $20,580 G4-7DEZ 1.5
S3425 5K509EN1328MRA3 3620 $31,811 G6-7DAN 5.2 S3567 5KE324AC215 542 $1,687 G4-7DEZ 1.3
S3426 5K509EN1328MRA2 3620 $33,489 G6-7DAN 5.2 S3569 5KE326AC215 610 $1,965 G4-7DEZ 1.4
S3427 5K509EN1328MRA1 3620 $35,137 G6-7DAN 5.2 S3570 5KE364AC215 719 $2,780 G4-7DEZ 1.4
S3428 5K509EN1328M 3620 $38,346 G6-7DAN 5.2 S3571 5KE365AC215 796 $3,200 G4-7DEZ 1.4
S3429 5K511EN1081MRA2 4540 $41,008 G6-7DAN 5.2 S3572 5KE404AC215 981 $4,200 G4-7DEZ 1.4
S3430 5K511EN1081MRA1 4540 $42,315 G6-7DAN 5.2 S3573 5KE405AC218 1094 $5,125 G4-7DEZ 1.5
S3431 5K511EN1081M 4540 $45,375 G6-7DAN 5.2 S3574 5KE444AC218 1320 $7,485 G4-7DEZ 1.5
S3501 5KE324AC304 529 $1,700 G4-7DEZ 1.3 S3575 5KE445AC218 1430 $10,095 G4-7DEZ 1.5
S3502 5KE324AC305 544 $1,700 G4-7DEZ 1.3 S3601 5KE184ATF205 104 $585 G4-7DEF 6.12
S3503 5KE326AC304 573 $1,950 G4-7DEZ 1.3 S3602 5KE213ATF205 128 $719 G4-7DEF 6.12
S3504 5KE326AC305 573 $1,950 G4-7DEZ 1.3 S3603 5KE215ATF205 180 $855 G4-7DEF 6.12
S3505 5KE324AC204 542 $1,686 G4-7DEZ 1.3 S3604 5KE254ATF205 260 $1,045 G4-7DEF 6.12
S3506 5KE324AC205 542 $1,687 G4-7DEZ 1.3 S3605 5KE256ATF205 310 $1,271 G4-7DEF 6.12
S3507 5KE324AC206 542 $1,686 G4-7DEZ 1.3 S3606 5KE284ATF205 394 $1,491 G4-7DEF 6.12
S3508 5KE364AC304 726 $3,000 G4-7DEZ 1.3 S3607 5KE286ATF205 436 $1,655 G4-7DEF 6.12
S3509 5KE364AC308 726 $3,000 G4-7DEZ 1.3 S3608 5KE324ATF205 575 $1,925 G4-7DEF 6.12
S3510 5KE324AC114 535 $2,103 G4-7DEZ 1.4 S3609 5KE326ATF205 575 $2,232 G4-7DEF 6.12
S3511 5KE324AC115 535 $2,104 G4-7DEZ 1.4 S3610 5KE364ATF215 730 $2,771 G4-7DEF 6.12
S3512 5KE326AC204 610 $1,965 G4-7DEZ 1.4 S3611 5KE365ATF215 838 $3,345 G4-7DEF 6.12
S3513 5KE326AC205 610 $1,965 G4-7DEZ 1.4 S3612 5KE404ATF215 1045 $4,275 G4-7DEF 6.12
S3514 5KE365AC304 803 $3,455 G4-7DEZ 1.4 S3613 5KE405ATF215 1225 $5,101 G4-7DEF 6.12
S3515 5KE365AC308 803 $3,455 G4-7DEZ 1.4 S3614 5KE444ATF218 1430 $6,705 G4-7DEF 6.12
S3516 5KE326AC114 603 $2,730 G4-7DEZ 1.4 S3615 5KE445ATF218 1610 $8,789 G4-7DEF 6.12
S3517 5KE326AC115 603 $2,730 G4-7DEZ 1.4 S3616 5KE182ATF105 73 $605 G4-7DEF 6.12
S3518 5KE364AC204 719 $2,780 G4-7DEZ 1.4 S3617 5KE184ATF105 93 $725 G4-7DEF 6.12
S3519 5KE364AC205 719 $2,780 G4-7DEZ 1.4 S3618 5KE213ATF105 128 $890 G4-7DEF 6.12
S3520 5KE404AC304 970 $3,895 G4-7DEZ 1.4 S3619 5KE215ATF105 157 $1,050 G4-7DEF 6.12
S3521 5KE404AC308 970 $3,895 G4-7DEZ 1.4 S3620 5KE254ATF105 260 $1,275 G4-7DEF 6.12
S3522 5KE364AC114 695 $3,800 G4-7DEZ 1.4 S3621 5KE256ATF105 307 $1,483 G4-7DEF 6.12
S3523 5KE364AC115 695 $3,800 G4-7DEZ 1.4 S3622 5KE284ATF105 378 $1,660 G4-7DEF 6.12
S3524 5KE365AC204 796 $3,200 G4-7DEZ 1.4 S3623 5KE286ATF105 406 $1,950 G4-7DEF 6.12
S3525 5KE365AC205 796 $3,200 G4-7DEZ 1.4 S3624 5KE324ATF105 595 $2,685 G4-7DEF 6.12
S3526 5KE405AC304 1105 $4,930 G4-7DEZ 1.4 S3625 5KE326ATF105 661 $2,985 G4-7DEF 6.12
S3527 5KE405AC308 1105 $4,930 G4-7DEZ 1.4 S3626 5KE364ATF115 674 $3,297 G4-7DEF 6.12
S3528 5KE365AC114 757 $4,950 G4-7DEZ 1.4 S3627 5KE365ATF115 763 $4,260 G4-7DEF 6.12
S3529 5KE365AC115 757 $4,950 G4-7DEZ 1.4 S3628 5KE404ATF115 1031 $5,048 G4-7DEF 6.12
S3530 5KE404AC204 981 $4,200 G4-7DEZ 1.4 S3629 5KE405ATF115 1124 $6,350 G4-7DEF 6.12
S3531 5KE404AC205 981 $4,200 G4-7DEZ 1.4 S3630 5KE444ATF118 1510 $9,350 G4-7DEF 6.12
S3532 5KE444AC304 1166 $6,215 G4-7DEZ 1.4 S4116 5KE405SFC118 1259 $6,296 G4-7SEZ 1.10
S3533 5KE444AC308 1166 $6,215 G4-7DEZ 1.4 S4117 5KE405SFC208 1299 $5,810 G4-7SEZ 1.10
S3534 5KE404AC114 931 $6,200 G4-7DEZ 1.5 S4118 5KE444SFC308 1671 $8,400 G4-7SEZ 1.10
S3535 5KE404AC118 931 $6,200 G4-7DEZ 1.5 S4119 5KE444SFC208 1554 $7,648 G4-7SEZ 1.11
S3536 5KE405AC204 1094 $5,125 G4-7DEZ 1.5 S4120 5KE445SFC308 1775 $9,780 G4-7SEZ 1.11
S3537 5KE405AC208 1094 $5,125 G4-7DEZ 1.5 S4121 5KE445SFC118 1722 $9,886 G4-7SEZ 1.11
S3538 5KE445AC304 1276 $7,815 G4-7DEZ 1.5 S4122 5KE445SFC208 1739 $8,891 G4-7SEZ 1.11

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Catalog Number to Model Number

Wt List Price Page Wt List Price Page 13.15
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
S4123 5KE405SFC215 1299 $5,810 G4-7SEZ 1.10 S5243 5KE254KTE105 290 $1,016 G4-7TECZ 1.12
S4175 5KE405SFC114 1259 $6,296 G4-7SEZ 1.10 S5245 5KE254KTE205 260 $1,009 G4-7TECZ 1.12

Cross Reference Guide

S4176 5KE405SFC204 1299 $5,810 G4-7SEZ 1.10 S5250 5KE256KTE105 325 $1,272 G4-7TECZ 1.12
S4177 5KE444SFC304 1671 $8,400 G4-7SEZ 1.10 S5252 5KE256KTE205 290 $1,277 G4-7TECZ 1.12
S4178 5KE444SFC114 1623 $8,230 G4-7SEZ 1.11 S5256 5KE284KTE115 430 $1,593 G4-7TECZ 1.13
S4179 5KE444SFC204 1554 $7,648 G4-7SEZ 1.11 S5258 5KE284KTE205 430 $1,570 G4-7TECZ 1.13
S4180 5KE445SFC304 1775 $9,780 G4-7SEZ 1.11 S5262 5KE286KTE115 465 $1,863 G4-7TECZ 1.13
S4181 5KE445SFC114 1722 $9,886 G4-7SEZ 1.11 S5265 5KE286KTE205 455 $1,827 G4-7TECZ 1.13
S4182 5KE445SFC204 1739 $8,891 G4-7SEZ 1.11 S5506 5KE324ATE205 580 $1,687 G4-7DEZ 1.3
S4202 5KE145BTE105 52 $321 G4-7TEZ 1.8 S5511 5KE324ATE115 606 $2,104 G4-7DEZ 1.4
S4210 5KE143BTE105 50 $282 G4-7TEZ 1.8 S5513 5KE326ATE205 639 $1,965 G4-7DEZ 1.4
S4211 5KE143BTE205 50 $243 G4-7TEZ 1.8 S5517 5KE326ATE115 692 $2,730 G4-7DEZ 1.4
S4214 5KE145BTE202 56 $262 G4-7TEZ 1.8 S5519 5KE364ATE205 700 $2,780 G4-7DEZ 1.4
S4215 5KE145BTE205 56 $282 G4-7TEZ 1.8 S5523 5KE364ATE115 686 $3,800 G4-7DEZ 1.4
S4219 5KE182BTE205 80 $320 G4-7TEZ 1.8 S5525 5KE365ATE205 838 $3,200 G4-7DEZ 1.4
S4221 5KE182BTE105 78 $357 G4-7TEZ 1.8 S5529 5KE365ATE115 812 $4,950 G4-7DEZ 1.4
S4225 5KE184BTE205 95 $380 G4-7TEZ 1.8 S5531 5KE404ATE205 870 $4,200 G4-7DEZ 1.4
S4227 5KE184BTE105 92 $442 G4-7TEZ 1.8 S5535 5KE404ATE118 890 $6,200 G4-7DEZ 1.5
S4229 5KE213BTE105 138 $576 G4-7TEZ 1.9 S5537 5KE405ATE208 960 $5,125 G4-7DEZ 1.5
S4231 5KE213BTE205 140 $510 G4-7TEZ 1.9 S5541 5KE405ATE118 1150 $7,600 G4-7DEZ 1.5
S4236 5KE215BTE105 146 $677 G4-7TEZ 1.9 S5543 5KE444ATE208 1330 $7,485 G4-7DEZ 1.5
S4238 5KE215BTE205 152 $630 G4-7TEZ 1.9 S5547 5KE444ATE118 1310 $11,485 G4-7DEZ 1.5
S4243 5KE254BTE105 290 $888 G4-7TEZ 1.9 S5549 5KE445ATE208 1510 $10,095 G4-7DEZ 1.5
S4245 5KE254BTE205 260 $881 G4-7TEZ 1.9 S5553 5KE445ATE118 1480 $14,225 G4-7DEZ 1.5
S4250 5KE256BTE105 325 $1,136 G4-7TEZ 1.9 S5559 5KE445ATE121 1480 $17,363 G4-7DEZ 1.5
S4252 5KE256BTE205 290 $1,141 G4-7TEZ 1.9 S5563 5KE447ATE121 2100 $19,850 G4-7DEZ 1.5
S4256 5KE284BTE115 425 $1,432 G4-7TEZ 1.10 S5567 5KE324ATE215 606 $1,687 G4-7DEZ 1.3
S4258 5KE284BTE205 430 $1,366 G4-7TEZ 1.10 S5569 5KE326ATE215 692 $1,965 G4-7DEZ 1.4
S4262 5KE286BTE115 465 $1,666 G4-7TEZ 1.10 S5570 5KE364ATE215 686 $2,780 G4-7DEZ 1.4
S4265 5KE286BTE205 455 $1,547 G4-7TEZ 1.10 S5571 5KE365ATE215 812 $3,200 G4-7DEZ 1.4
S4334 5KE444SFC118 1623 $8,230 G4-7SEZ 1.11 S5572 5KE404ATE215 890 $4,200 G4-7DEZ 1.4
S4346 5KE405SFC115 1259 $6,296 G4-7SEZ 1.10 S5573 5KE405ATE218 1150 $5,125 G4-7DEZ 1.5
S4347 5KE405SFC205 1299 $5,810 G4-7SEZ 1.10 S5574 5KE444ATE218 1310 $7,485 G4-7DEZ 1.5
S4348 5KE444SFC218 1554 $7,648 G4-7SEZ 1.11 S5575 5KE445ATE218 1480 $10,095 G4-7DEZ 1.5
S4349 5KE445SFC218 1739 $8,891 G4-7SEZ 1.11 V824 5KS182SAE5705 76 $1,029 G6-7VIL 6.8
S4351 5KE449SAA308 2730 $14,800 G4-7SEZ 1.11 V825 5KS184SAE5705 101 $1,304 G6-7VIL 6.8
S4352 5KE447SAA208 2560 $10,814 G4-7SEZ 1.11 V826 5KS213SAE5705 200 $1,453 G6-7VIL 6.8
S4353 5KE449SAA208 2580 $13,567 G4-7SEZ 1.11 V827 5KS215SAE5705 220 $1,604 G6-7VIL 6.8
S4384 5KE447SAA114 2560 $12,506 G4-7SEZ 1.11 V828 5KS254SAE5705 315 $1,814 G6-7VIL 6.8
S4385 5KE447SAA204 2560 $10,814 G4-7SEZ 1.11 V829 5KS256SAC5705 350 $2,039 G6-7VIL 6.8
S4386 5KE449SAA304 2730 $14,800 G4-7SEZ 1.11 V830 5KS284SAE5705 460 $2,281 G6-7VIL 6.8
S4387 5KE447SAA120 2730 $12,506 G4-7SEZ 1.11 V831 5KS286SAE5705 510 $2,460 G6-7VIL 6.8
S4503 5KE182ATE105 85 $403 G4-7DEZ 1.2 V832 5KS324ST5711 650 $4,710 G6-7VIL 6.8
S4504 5KE182ATE205 91 $288 G4-7DEZ 1.2 V833 5KS182SAE6705 76 $1,029 G6-7VIL 6.8
S4509 5KE184ATE105 93 $480 G4-7DEZ 1.2 V834 5KS184SAE6705 101 $1,118 G6-7VIL 6.8
S4511 5KE184ATE205 93 $348 G4-7DEZ 1.2 V835 5KS213SAE6705 200 $1,426 G6-7VIL 6.8
S4516 5KE213ATE105 133 $630 G4-7DEZ 1.2 V836 5KS215SAE6705 220 $1,569 G6-7VIL 6.8
S4518 5KE213ATE205 137 $475 G4-7DEZ 1.2 V837 5KS254SAE6705 315 $1,908 G6-7VIL 6.8
S4523 5KE215ATE105 160 $807 G4-7DEZ 1.3 V838 5KS256SAE6705 350 $2,123 G6-7VIL 6.8
S4525 5KE215ATE205 163 $590 G4-7DEZ 1.2 V839 5KS284SAE6705 460 $2,418 G6-7VIL 6.8
S4530 5KE254ATE105 240 $971 G4-7DEZ 1.3 V840 5KS286SAE6705 510 $2,662 G6-7VIL 6.8
S4532 5KE254ATE205 240 $815 G4-7DEZ 1.3 V841 5KS324ST6711 730 $4,267 G6-7VIL 6.8
S4537 5KE256ATE105 307 $1,186 G4-7DEZ 1.3 V3107 5KE213DTT5005 220 $1,174 G5-7VHSB 6.2
S4539 5KE256ATE205 307 $1,033 G4-7DEZ 1.3 V3108 5KE213DTT5003 220 $1,086 G5-7VHSB 6.2
S4543 5KE284ATE115 390 $1,396 G4-7DEZ 1.3 V3109 5KE213DTT5002 220 $1,008 G5-7VHSB 6.2
S4544 5KE284ATE205 370 $1,155 G4-7DEZ 1.3 V3115 5KE213DTT6005 220 $1,030 G5-7VHSB 6.2
S4547 5KE286ATE115 410 $1,791 G4-7DEZ 1.3 V3116 5KE213DTT6002 220 $998 G5-7VHSB 6.2
S4549 5KE286ATE205 400 $1,325 G4-7DEZ 1.3 V3139 5KE215DTT5005 220 $1,380 G5-7VHSB 6.2
S4804 5KE145ATE105 52 $332 G4-7DEZ 1.2 V3141 5KE215DTT6005 220 $1,174 G5-7VHSB 6.2
S5210 5KE143KTE105 15 $328 G4-7TECZ 1.12 V3157 5KE254DTT5005 340 $1,515 G5-7VHSB 6.2
S5211 5KE143KTE205 50 $288 G4-7TECZ 1.12 V3158 5KE254DTT6005 340 $1,419 G5-7VHSB 6.2
S5213 5KE145KTE105 52 $368 G4-7TECZ 1.12 V3170 5KE256DTT5001 370 $1,734 G5-7VHSB 6.2
S5214 5KE145KTE202 56 $308 G4-7TECZ 1.12 V3171 5KE256DTT5005 370 $1,734 G5-7VHSB 6.2
S5215 5KE145KTE205 56 $328 G4-7TECZ 1.12 V3173 5KE256DTT6001 370 $1,633 G5-7VHSB 6.2
S5216 5KE145KTE305 56 $378 G4-7TECZ 1.12 V3174 5KE256DTT6005 370 $1,633 G5-7VHSB 6.2
S5219 5KE182KTE205 80 $376 G4-7TECZ 1.12 V3177 5KE256DTT7001 370 $1,770 G5-7VHSB 6.2
S5221 5KE182KTE105 78 $413 G4-7TECZ 1.12 V3178 5KE256DTT7005 370 $1,645 G5-7VHSB 6.2
S5225 5KE184KTE205 95 $436 G4-7TECZ 1.12 V3188 5KE284DTT5005 507 $1,770 G5-7VHSB 6.2
S5227 5KE184KTE105 92 $498 G4-7TECZ 1.12 V3189 5KE284DTT6005 507 $1,832 G5-7VHSB 6.2
S5229 5KE213KTE105 138 $643 G4-7TECZ 1.12 V3190 5KE284DTT6001 507 $1,832 G5-7VHSB 6.2
S5231 5KE213KTE205 140 $577 G4-7TECZ 1.12 V3191 5KE284DTT7005 507 $1,934 G5-7VHSB 6.2
S5236 5KE215KTE105 146 $744 G4-7TECZ 1.12 V3197 5KE286DTT5005 507 $2,350 G5-7VHSB 6.2
S5238 5KE215KTE205 152 $697 G4-7TECZ 1.12 V3198 5KE286DTT6005 507 $2,074 G5-7VHSB 6.2

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Catalog Number to Model Number

13.16 Wt List Price Page Wt List Price Page
Cat No. Model (lbs) Price Symbol Number Cat No. Model (lbs) Price Symbol Number
V3199 5KE286DTT6001 507 $2,074 G5-7VHSB 6.2 Y8312 249A9510AAG28 $94 G5-7KITS 6.6
V3407 5KE324DTT5002 790 $2,725 G5-7VHSB 6.2 Y8313 249A9513AA01 $112 G5-7KITS 6.5
Cross Reference Guide

V3409 5KE324DTT6003 760 $2,180 G5-7VHSB 6.2 Y8314 249A9513AA02 $117 G5-7KITS 6.5
V3410 5KE324DTT6007 760 $2,180 G5-7VHSB 6.2 Y8315 249A9513AA03 $120 G5-7KITS 6.5
V3411 5KE324DTT6002 760 $2,180 G5-7VHSB 6.2 Y8320 249A9515AAG1 $488 G5-7KITS 6.5
V3420 5KE326DTT6003 760 $2,857 G5-7VHSB 6.2 Y8321 249A9515AAG2 $488 G5-7KITS 6.5
V3421 5KE326DTT6007 760 $2,557 G5-7VHSB 6.2 Y8322 249A9515AAG3 $488 G5-7KITS 6.5
V3422 5KE326DTT6002 760 $2,857 G5-7VHSB 6.2 Y8323 249A9515AAG4 $488 G5-7KITS 6.5
V3423 5KE326DTT7002 885 $2,785 G5-7VHSB 6.2 Y8324 249A9515AAG5 $488 G5-7KITS 6.5
V3428 5KE364DTT5002 1102 $3,995 G5-7VHSB 6.2 Y8325 249A9515AAG6 $488 G5-7KITS 6.5
V3429 5KE364DTT6007 1102 $3,444 G5-7VHSB 6.2 Y8326 249A9513AAG7 $488 G5-7KITS 6.5
V3430 5KE364DTT6009 1102 $3,444 G5-7VHSB 6.2 Y8327 249A9515AAG8 $563 G5-7KITS 6.5
V3431 5KE364DTT6003 1102 $3,444 G5-7VHSB 6.2 Y8328 249A9515AAG9 $563 G5-7KITS 6.5
V3435 5KE364DTT7002 1102 $3,488 G5-7VHSB 6.2 Y8329 249A9515AAG10 $563 G5-7KITS 6.5
V3440 5KE365DTT6007 1102 $4,050 G5-7VHSB 6.3 Y8330 249A9515AAG11 $563 G5-7KITS 6.5
V3441 5KE365DTT6009 1102 $4,050 G5-7VHSB 6.3 Y8331 249A9515AAG12 $563 G5-7KITS 6.5
V3442 5KE365DTT6000 1102 $4,050 G5-7VHSB 6.3 Y8332 249A9515AAG13 $563 G5-7KITS 6.5
V3450 5KE324DTT5003 760 $2,725 G5-7VHSB 6.2 Y8333 249A9513AAG14 $563 G5-7KITS 6.5
V3451 5KE404DTT6002 1590 $5,325 G5-7VHSB 6.3 Y8334 249A9515AAG15 $600 G5-7KITS 6.5
V3453 5KE404DTT6003 1590 $5,325 G5-7VHSB 6.3 Y8335 249A9515AAG16 $600 G5-7KITS 6.5
V3456 5KE405DTT6002 1590 $5,929 G5-7VHSB 6.3 Y8336 249A9515AAG17 $600 G5-7KITS 6.5
V3464 5KE444DTT6003 2075 $7,360 G5-7VHSB 6.3 Y8337 249A9515AAG18 $600 G5-7KITS 6.5
V3466 5KE444DTT6002 2075 $7,360 G5-7VHSB 6.3 Y8338 249A9515AAG19 $600 G5-7KITS 6.5
V3468 5KE444DTT7009 2075 $7,806 G5-7VHSB 6.3 Y8339 249A9515AAG20 $600 G5-7KITS 6.5
V3470 5KE445DTT6003 2260 $9,962 G5-7VHSB 6.3 Y8340 249A9515AAG21 $600 G5-7KITS 6.5
V3483 5KE445DTT6002 2260 $9,962 G5-7VHSB 6.3 Y8341 249A9513AAG22 $600 G5-7KITS 6.5
V3551 5KE326DTT5002 760 $3,179 G5-7VHSB 6.2 Y8360 249A9510AAG29 $94 G5-7KITS 6.6
V3552 5KE364DTT6000 1102 $3,444 G5-7VHSB 6.2 Y8361 249A9510AAG30 $94 G5-7KITS 6.6
V3553 5KE404DTT7002 1590 $4,791 G5-7VHSB 6.2 Y8362 249A9515AAG23 $750 G5-7KITS 6.5
V3554 5KE365DTT6003 1102 $4,050 G5-7VHSB 6.3 Y8363 249A9515AAG24 $750 G5-7KITS 6.5
V3555 5KE405DTT7002 1590 $5,733 G5-7VHSB 6.3 Y8364 249A9515AAG25 $750 G5-7KITS 6.5
V3556 5KE444DTT7002 2075 $7,806 G5-7VHSB 6.3 Y8365 249A9515AAG26 $750 G5-7KITS 6.5
Y8250 249A9512AAG1 $112 G5-7KITS 6.5 Y8366 249A9515AAG27 $750 G5-7KITS 6.5
Y8251 249A9512AAG2 $112 G5-7KITS 6.5 Y8367 249A9515AAG28 $750 G5-7KITS 6.5
Y8253 249A9512AAG3 $112 G5-7KITS 6.5 Y8368 249A9515AAG29 $750 G5-7KITS 6.5
Y8254 249A9512AAG4 $112 G5-7KITS 6.5 Y8369 249A9515AAG30 $750 G5-7KITS 6.5
Y8255 249A9512AAG5 $117 G5-7KITS 6.5 Y8370 249A9515AAG31 $750 G5-7KITS 6.5
Y8256 249A9512AAG6 $117 G5-7KITS 6.5 Y8371 249A9515AAG32 $750 G5-7KITS 6.5
Y8257 249A9512AAG7 $117 G5-7KITS 6.5 Y8372 249A9515AAG33 $750 G5-7KITS 6.5
Y8258 249A9512AAG8 $117 G5-7KITS 6.5 Y8373 249A9515AAG34 $750 G5-7KITS 6.5
Y8259 249A9512AAG9 $117 G5-7KITS 6.5 Y8374 249A9515AAG35 $750 G5-7KITS 6.5
Y8260 249A9512AAG10 $120 G5-7KITS 6.5 Y8375 249A9513AAG36 $750 G5-7KITS 6.5
Y8261 249A9512AAG11 $120 G5-7KITS 6.5 Y8383 249A9510AAP31 $157 G5-7KITS 6.6
Y8262 249A9512AAG12 $120 G5-7KITS 6.5 Y8384 249A9510AAP32 $157 G5-7KITS 6.6
Y8263 249A9512AAG13 $120 G5-7KITS 6.5 Y8385 249A9510AAP33 $157 G5-7KITS 6.6
Y8264 249A9512AAG14 $120 G5-7KITS 6.5 Y8386 249A9510AAP34 $157 G5-7KITS 6.6
Y8284 249A9510AAG1 $73 G5-7KITS 6.6 Y8387 249A9510AAP35 $157 G5-7KITS 6.6
Y8285 249A9510AAG2 $73 G5-7KITS 6.6 Y8388 249A9510AAP36 $157 G5-7KITS 6.6
Y8286 249A9510AAG3 $73 G5-7KITS 6.6 Y8389 249A9510AAP37 $157 G5-7KITS 6.6
Y8287 249A9510AAG4 $73 G5-7KITS 6.6 Y8390 249A9510AAP38 $157 G5-7KITS 6.6
Y8288 249A9510AAG5 $73 G5-7KITS 6.6 Y8391 249A9510AAP39 $157 G5-7KITS 6.6
Y8289 249A9510AAG6 $73 G5-7KITS 6.6 Y8392 249A9510AAP40 $157 G5-7KITS 6.6
Y8290 249A9510AAG7 $71 G5-7KITS 6.6 Y8393 249A9510AAP41 $157 G5-7KITS 6.6
Y8291 249A9510AAG8 $71 G5-7KITS 6.6 Y8394 249A9510AAP42 $157 G5-7KITS 6.6
Y8292 249A9510AAG9 $71 G5-7KITS 6.6 Y8395 249A9510AAP43 $157 G5-7KITS 6.6
Y8293 249A9510AAG10 $71 G5-7KITS 6.6
Y8294 249A9510AAG11 $71 G5-7KITS 6.6
Y8295 249A9510AAG12 $90 G5-7KITS 6.6
Y8296 249A9510AAG13 $90 G5-7KITS 6.6
Y8297 249A9510AAG14 $90 G5-7KITS 6.6
Y8298 249A9510AAG15 $90 G5-7KITS 6.6
Y8299 249A9510AAG16 $90 G5-7KITS 6.6
Y8301 249A9510AAG17 $90 G5-7KITS 6.6
Y8302 249A9510AAG18 $90 G5-7KITS 6.6
Y8303 249A9510AAG19 $90 G5-7KITS 6.6
Y8304 249A9510AAG20 $90 G5-7KITS 6.6
Y8305 249A9510AAG21 $90 G5-7KITS 6.6
Y8306 249A9510AAG22 $90 G5-7KITS 6.6
Y8307 249A9510AAG23 $90 G5-7KITS 6.6
Y8308 249A9510AAG24 $94 G5-7KITS 6.6
Y8309 249A9510AAG25 $94 G5-7KITS 6.6
Y8310 249A9510AAG26 $94 G5-7KITS 6.6
Y8311 249A9510AAG27 $94 G5-7KITS 6.6

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.17
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
153B1004ACG120 A337 $89 G4-7KITS 1.22 235A4753BJ1 A293 $480 G4-7KITS 3.35
153B1004ACG120 A337 $89 G4-7KITS 2.11 235A4753BJ2 A294 $480 G4-7KITS 3.35

Cross Reference Guide

153B1004ACG120 A337 $89 G4-7KITS 3.36 235A4753BJ3 A295 $480 G4-7KITS 3.35
153B1069AAG01 A234 $111 G4-7KITS 1.22 235A4753BK1 A296 $550 G4-7KITS 3.35
153B1069AAG01 A234 $111 G4-7KITS 2.11 235A4753BK2 A297 $550 G4-7KITS 3.35
153B1069AAG01 A234 $111 G4-7KITS 3.34 235A4753BK3 A298 $550 G4-7KITS 3.35
153B1069AAG01 A234 $111 G4-7KITS 4.6 235A4985ANG01 A544 $1,842 G4-7KITS 4.6
153B1069AAG02 A235 $111 G4-7KITS 1.22 235A4985ANG01 A545 $1,842 G4-7KITS 4.6
153B1069AAG02 A235 $111 G4-7KITS 2.11 235A4985APG01 A543 $1,027 G4-7KITS 4.6
153B1069AAG02 A235 $111 G4-7KITS 3.34 235A4985ARG01 A542 $1,027 G4-7KITS 4.6
153B1069AAG02 A235 $111 G4-7KITS 4.6 249A4234AAG03 A344 $68 G4-7KITS 3.34
153B1069AAG03 A236 $111 G4-7KITS 1.22 249A4234AAG07 A346 $68 G4-7KITS 3.34
153B1069AAG03 A236 $111 G4-7KITS 2.11 249A4234AAG20 A343 $68 G4-7KITS 3.34
153B1069AAG03 A236 $111 G4-7KITS 3.34 249A4234AAG21 A345 $68 G4-7KITS 3.34
153B1069AAG03 A236 $111 G4-7KITS 4.6 249A4234ABG02 A300 $158 G6-7KITS 1.22
153B1069ANG01 A237 $188 G4-7KITS 1.22 249A4234ABG02 A300 $158 G6-7KITS 2.11
153B1069ANG01 A237 $188 G4-7KITS 2.11 249A4234ABG03 A301 $158 G6-7KITS 1.22
153B1069ANG01 A237 $188 G4-7KITS 3.34 249A4234ABG03 A301 $158 G6-7KITS 2.11
153B1069ANG01 A237 $188 G4-7KITS 4.6 249A4267AD-G01 A1201 $105 G4-7KITS 3.30
153B1069ANG02 A241 $203 G4-7KITS 1.22 249A4267AD-G01 A1201 $105 G4-7KITS 3.34
153B1069ANG02 A241 $203 G4-7KITS 2.11 249A4267AD-G02 A1202 $110 G4-7KITS 3.30
153B1069ANG02 A241 $203 G4-7KITS 3.34 249A4267AD-G02 A1202 $110 G4-7KITS 3.34
153B1069ANG02 A241 $203 G4-7KITS 4.6 249A4267AD-G03 A1203 $125 G4-7KITS 3.30
153B1069ANG03 A240 $188 G4-7KITS 1.22 249A4267AD-G03 A1203 $125 G4-7KITS 3.34
153B1069ANG03 A240 $188 G4-7KITS 3.34 249A4267AD-G04 A1204 $136 G4-7KITS 3.30
153B1069ANG03 A240 $188 G4-7KITS 4.6 249A4267AD-G04 A1204 $136 G4-7KITS 3.34
153B1069ANG04 A244 $203 G4-7KITS 1.22 249A4267AD-G05 A1205 $155 G4-7KITS 3.30
153B1069ANG04 A244 $203 G4-7KITS 2.11 249A4267AD-G05 A1205 $155 G4-7KITS 3.34
153B1069ANG04 A244 $203 G4-7KITS 3.34 249A4267AD-G06 A1206 $173 G4-7KITS 3.30
153B1069ANG04 A244 $203 G4-7KITS 4.6 249A4267AD-G06 A1206 $173 G4-7KITS 3.34
153B1069ANG05 A238 $188 G4-7KITS 1.22 249A4321ABG15 A735 $261 G6-7KITS 4.6
153B1069ANG05 A238 $188 G4-7KITS 2.11 249A4321ABG16 A736 $439 G6-7KITS 4.6
153B1069ANG05 A238 $188 G4-7KITS 3.34 249A4321ABG17 A737 $575 G6-7KITS 4.6
153B1069ANG05 A238 $188 G4-7KITS 4.6 249A4321ABG19 A739 $575 G6-7KITS 4.6
153B1069ANG06 A242 $203 G4-7KITS 1.22 249A4321AGG01 A927 $360 G6-7KITS 5.2
153B1069ANG06 A242 $203 G4-7KITS 2.11 249A4321AMG01 A761 $261 G4-7KITS 3.33
153B1069ANG06 A242 $203 G4-7KITS 3.34 249A4321AMG02 A762 $261 G4-7KITS 3.33
153B1069ANG06 A242 $203 G4-7KITS 4.6 249A4321AMG03 A763 $561 G4-7KITS 2.10
153B1073BDG02 A239 $107 G4-7KITS 1.22 249A4321AMG03 A763 $561 G4-7KITS 3.33
153B1073BDG02 A239 $107 G4-7KITS 2.11 249A4321AMG04 A764 $561 G4-7KITS 2.10
153B1073BDG02 A239 $107 G4-7KITS 3.34 249A4321AMG04 A764 $561 G4-7KITS 3.33
153B1073BDG02 A239 $107 G4-7KITS 4.6 249A4321AMG05 A765 $590 G4-7KITS 2.10
153B1073BEG01 A233 $107 G4-7KITS 1.22 249A4321AMG05 A765 $590 G4-7KITS 3.33
153B1073BEG01 A233 $107 G4-7KITS 2.11 249A4321AMG06 A766 $590 G4-7KITS 2.10
153B1073BEG01 A233 $107 G4-7KITS 3.34 249A4321AMG06 A766 $590 G4-7KITS 3.33
153B1073BEG01 A233 $107 G4-7KITS 4.6 249A4321AMG07 A767 $1,408 G4-7KITS 2.10
227B1056AA-G01 A320 6.16 249A4321AMG07 A767 $1,408 G4-7KITS 3.33
227B1056AB-G01 A323 6.16 249A4321AMG08 A768 $1,408 G4-7KITS 2.10
227B1056AC-G01 A324 6.16 249A4321AMG08 A768 $1,408 G4-7KITS 3.33
227B1056AD-G01 A325 6.16 249A4321ARG01 A991 $608 G4-7KITS 3.33
227B1056AD-G02 A326 6.16 249A4321ARG02 A992 $608 G4-7KITS 3.33
227B1056AD-G03 A327 6.16 249A4321ARG03 A993 $1,028 G4-7KITS 3.33
227B1058AA-G01 A322 6.16 249A4321ARG04 A994 $1,028 G4-7KITS 3.33
227B1058AA-G02 A321 6.16 249A4321ARG05 A995 $1,400 G4-7KITS 3.33
235A4575GE001 A826 $109 G4-7KITS 3.34 249A4321ARG06 A996 $1,400 G4-7KITS 3.33
235A4575GE001 A826 $109 G4-7KITS 4.6 249A4321ARG07 A997 $1,457 G4-7KITS 3.33
235A4575GE003 A828 $140 G4-7KITS 3.34 249A4321ARG08 A998 $1,679 G4-7KITS 3.33
235A4575GE003 A828 $140 G4-7KITS 4.6 249A9500AAPT21 A272 $98 G4-7KITS 1.21
235A4575GE005 A830 $459 G4-7KITS 3.34 249A9500AAPT22 A274 $134 G4-7KITS 1.21
235A4575GE005 A830 $459 G4-7KITS 4.6 249A9500AAPT23 A280 $167 G4-7KITS 1.21
235A4575GE007 A832 $549 G4-7KITS 3.34 249A9500AAPT24 A281 $224 G4-7KITS 1.21
235A4575GE007 A832 $549 G4-7KITS 4.6 249A9500AAPT25 A283 $297 G4-7KITS 1.21
235A4575GS1 A1007 $336 G4-7KITS 3.34 249A9500AAPT6 A282 $224 G4-7KITS 1.21
235A4753BF1 A284 $339 G4-7KITS 3.35 249A9500ABPT10 A1074 $539 G4-7KITS 1.20
235A4753BF2 A285 $339 G4-7KITS 3.35 249A9500ABPT11 A1075 $785 G4-7KITS 1.20
235A4753BF4 A286 $339 G4-7KITS 3.35 249A9500ABPT12 A1076 $785 G4-7KITS 1.20
235A4753BG1 A287 $405 G4-7KITS 3.35 249A9500ABPT13 A1077 $857 G4-7KITS 1.20
235A4753BG2 A288 $405 G4-7KITS 3.35 249A9500ABPT14 A1078 $857 G4-7KITS 1.20
235A4753BG3 A289 $405 G4-7KITS 3.35 249A9500ABPT15 A1079 $993 G4-7KITS 1.20
235A4753BH1 A290 $405 G4-7KITS 3.35 249A9500ABPT16 A1080 $993 G4-7KITS 1.20
235A4753BH2 A291 $405 G4-7KITS 3.35 249A9500ABPT4 A268 $169 G4-7KITS 1.20
235A4753BH3 A292 $405 G4-7KITS 3.35 249A9500ABPT5 A270 $258 G4-7KITS 1.20

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.18 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
249A9500ABPT6 A269 $258 G4-7KITS 1.20 249A9514AAG05 A1025 $483 G4-7KITS 1.21
249A9500ABPT7 A1071 $418 G4-7KITS 1.20 249A9514AAG06 A1026 $483 G4-7KITS 1.21
Cross Reference Guide

249A9500ABPT8 A1072 $418 G4-7KITS 1.20 249A9514AAG07 A1027 $595 G4-7KITS 1.21
249A9500ABPT9 A1073 $539 G4-7KITS 1.20 249A9514AAG08 A1028 $595 G4-7KITS 1.21
249A9510AAG1 Y8284 $73 G5-7KITS 6.6 249A9515AAG1 Y8320 $488 G5-7KITS 6.5
249A9510AAG10 Y8293 $71 G5-7KITS 6.6 249A9515AAG10 Y8329 $563 G5-7KITS 6.5
249A9510AAG11 Y8294 $71 G5-7KITS 6.6 249A9515AAG11 Y8330 $563 G5-7KITS 6.5
249A9510AAG12 Y8295 $90 G5-7KITS 6.6 249A9515AAG12 Y8331 $563 G5-7KITS 6.5
249A9510AAG13 Y8296 $90 G5-7KITS 6.6 249A9515AAG13 Y8332 $563 G5-7KITS 6.5
249A9510AAG14 Y8297 $90 G5-7KITS 6.6 249A9515AAG15 Y8334 $600 G5-7KITS 6.5
249A9510AAG15 Y8298 $90 G5-7KITS 6.6 249A9515AAG16 Y8335 $600 G5-7KITS 6.5
249A9510AAG16 Y8299 $90 G5-7KITS 6.6 249A9515AAG17 Y8336 $600 G5-7KITS 6.5
249A9510AAG17 Y8301 $90 G5-7KITS 6.6 249A9515AAG18 Y8337 $600 G5-7KITS 6.5
249A9510AAG18 Y8302 $90 G5-7KITS 6.6 249A9515AAG19 Y8338 $600 G5-7KITS 6.5
249A9510AAG19 Y8303 $90 G5-7KITS 6.6 249A9515AAG2 Y8321 $488 G5-7KITS 6.5
249A9510AAG2 Y8285 $73 G5-7KITS 6.6 249A9515AAG20 Y8339 $600 G5-7KITS 6.5
249A9510AAG20 Y8304 $90 G5-7KITS 6.6 249A9515AAG21 Y8340 $600 G5-7KITS 6.5
249A9510AAG21 Y8305 $90 G5-7KITS 6.6 249A9515AAG23 Y8362 $750 G5-7KITS 6.5
249A9510AAG22 Y8306 $90 G5-7KITS 6.6 249A9515AAG24 Y8363 $750 G5-7KITS 6.5
249A9510AAG23 Y8307 $90 G5-7KITS 6.6 249A9515AAG25 Y8364 $750 G5-7KITS 6.5
249A9510AAG24 Y8308 $94 G5-7KITS 6.6 249A9515AAG26 Y8365 $750 G5-7KITS 6.5
249A9510AAG25 Y8309 $94 G5-7KITS 6.6 249A9515AAG27 Y8366 $750 G5-7KITS 6.5
249A9510AAG26 Y8310 $94 G5-7KITS 6.6 249A9515AAG28 Y8367 $750 G5-7KITS 6.5
249A9510AAG27 Y8311 $94 G5-7KITS 6.6 249A9515AAG29 Y8368 $750 G5-7KITS 6.5
249A9510AAG28 Y8312 $94 G5-7KITS 6.6 249A9515AAG3 Y8322 $488 G5-7KITS 6.5
249A9510AAG29 Y8360 $94 G5-7KITS 6.6 249A9515AAG30 Y8369 $750 G5-7KITS 6.5
249A9510AAG3 Y8286 $73 G5-7KITS 6.6 249A9515AAG31 Y8370 $750 G5-7KITS 6.5
249A9510AAG30 Y8361 $94 G5-7KITS 6.6 249A9515AAG32 Y8371 $750 G5-7KITS 6.5
249A9510AAG4 Y8287 $73 G5-7KITS 6.6 249A9515AAG33 Y8372 $750 G5-7KITS 6.5
249A9510AAG5 Y8288 $73 G5-7KITS 6.6 249A9515AAG34 Y8373 $750 G5-7KITS 6.5
249A9510AAG6 Y8289 $73 G5-7KITS 6.6 249A9515AAG35 Y8374 $750 G5-7KITS 6.5
249A9510AAG7 Y8290 $71 G5-7KITS 6.6 249A9515AAG4 Y8323 $488 G5-7KITS 6.5
249A9510AAG8 Y8291 $71 G5-7KITS 6.6 249A9515AAG5 Y8324 $488 G5-7KITS 6.5
249A9510AAG9 Y8292 $71 G5-7KITS 6.6 249A9515AAG6 Y8325 $488 G5-7KITS 6.5
249A9510AAP31 Y8383 $157 G5-7KITS 6.6 249A9515AAG8 Y8327 $563 G5-7KITS 6.5
249A9510AAP32 Y8384 $157 G5-7KITS 6.6 249A9515AAG9 Y8328 $563 G5-7KITS 6.5
249A9510AAP33 Y8385 $157 G5-7KITS 6.6 249A9573AAG01 A1050 $258 G4-7KITS 1.20
249A9510AAP34 Y8386 $157 G5-7KITS 6.6 249A9573AAG01 A1050 $258 G4-7KITS 2.10
249A9510AAP35 Y8387 $157 G5-7KITS 6.6 249A9573AAG02 A1051 $418 G4-7KITS 1.20
249A9510AAP36 Y8388 $157 G5-7KITS 6.6 249A9573AAG02 A1051 $418 G4-7KITS 2.10
249A9510AAP37 Y8389 $157 G5-7KITS 6.6 249A9573AAG03 A1052 $539 G4-7KITS 1.20
249A9510AAP38 Y8390 $157 G5-7KITS 6.6 249A9573AAG03 A1052 $539 G4-7KITS 2.10
249A9510AAP39 Y8391 $157 G5-7KITS 6.6 249A9573AAG04 A1053 $539 G4-7KITS 1.20
249A9510AAP40 Y8392 $157 G5-7KITS 6.6 249A9573AAG04 A1053 $539 G4-7KITS 2.10
249A9510AAP41 Y8393 $157 G5-7KITS 6.6 249A9573AAG05 A1054 $725 G4-7KITS 1.20
249A9510AAP42 Y8394 $157 G5-7KITS 6.6 249A9573AAG05 A1054 $725 G4-7KITS 2.10
249A9510AAP43 Y8395 $157 G5-7KITS 6.6 249A9573AAG06 A1055 $857 G4-7KITS 1.20
249A9512AAG1 Y8250 $112 G5-7KITS 6.5 249A9573AAG06 A1055 $857 G4-7KITS 2.10
249A9512AAG10 Y8260 $120 G5-7KITS 6.5 249A9573AAG07 A1056 $857 G4-7KITS 1.20
249A9512AAG11 Y8261 $120 G5-7KITS 6.5 249A9573AAG07 A1056 $857 G4-7KITS 2.10
249A9512AAG12 Y8262 $120 G5-7KITS 6.5 249A9573AAG08 A1057 $857 G4-7KITS 1.20
249A9512AAG13 Y8263 $120 G5-7KITS 6.5 249A9573AAG08 A1057 $857 G4-7KITS 2.10
249A9512AAG14 Y8264 $120 G5-7KITS 6.5 249A9573AAG09 A1058 $82 G4-7KITS 1.20
249A9512AAG2 Y8251 $112 G5-7KITS 6.5 249A9573AAG09 A1058 $82 G4-7KITS 2.10
249A9512AAG3 Y8253 $112 G5-7KITS 6.5 249A9573AAG10 A1059 $112 G4-7KITS 1.20
249A9512AAG4 Y8254 $112 G5-7KITS 6.5 249A9573AAG10 A1059 $112 G4-7KITS 2.10
249A9512AAG5 Y8255 $117 G5-7KITS 6.5 249A9573AAG11 A1060 $138 G4-7KITS 1.20
249A9512AAG6 Y8256 $117 G5-7KITS 6.5 249A9573AAG11 A1060 $138 G4-7KITS 2.10
249A9512AAG7 Y8257 $117 G5-7KITS 6.5 249A9573AAG12 A1061 $160 G4-7KITS 1.20
249A9512AAG8 Y8258 $117 G5-7KITS 6.5 249A9573AAG12 A1061 $160 G4-7KITS 2.10
249A9512AAG9 Y8259 $117 G5-7KITS 6.5 249A9573AAG13 A1062 $835 G4-7KITS 1.20
249A9513AA01 Y8313 $112 G5-7KITS 6.5 249A9573AAG13 A1062 $835 G4-7KITS 2.10
249A9513AA02 Y8314 $117 G5-7KITS 6.5 249A9573AAG14 A1063 $835 G4-7KITS 1.20
249A9513AA03 Y8315 $120 G5-7KITS 6.5 249A9573AAG14 A1063 $835 G4-7KITS 2.10
249A9513AAG14 Y8333 $563 G5-7KITS 6.5 249A9573ABG01 A1064 $98 G4-7KITS 1.21
249A9513AAG22 Y8341 $600 G5-7KITS 6.5 249A9573ABG01 A1064 $98 G4-7KITS 2.10
249A9513AAG36 Y8375 $750 G5-7KITS 6.5 249A9573ABG02 A1065 $134 G4-7KITS 1.21
249A9513AAG7 Y8326 $488 G5-7KITS 6.5 249A9573ABG02 A1065 $134 G4-7KITS 2.10
249A9514AAG01 A1021 $441 G4-7KITS 1.21 249A9573ABG03 A1066 $167 G4-7KITS 1.21
249A9514AAG02 A1022 $441 G4-7KITS 1.21 249A9573ABG03 A1066 $167 G4-7KITS 2.10
249A9514AAG03 A1023 $450 G4-7KITS 1.21 249A9573ABG04 A1067 $224 G4-7KITS 1.21
249A9514AAG04 A1024 $450 G4-7KITS 1.21 249A9573ABG04 A1067 $224 G4-7KITS 2.10

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.19
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
249A9573ABG05 A1068 $297 G4-7KITS 1.21 4002B5914ANP001 A1001 $145 G4-7KITS 3.34
249A9573ABG05 A1068 $297 G4-7KITS 2.10 4002B5914ANP001 A1001 $145 G4-7KITS 4.6

Cross Reference Guide

249A9573ABG06 A1069 $441 G4-7KITS 1.21 4002B5914ANP002 A1002 $145 G4-7KITS 3.34
249A9573ABG06 A1069 $441 G4-7KITS 2.10 4002B5914ANP002 A1002 $145 G4-7KITS 4.6
249A9598AA1 A100 $60 GO-1R 1.22 4002B5914ANP003 A1003 $158 G4-7KITS 3.34
249A9598AA1 A100 $60 GO-1R 2.11 4002B5914ANP003 A1003 $158 G4-7KITS 4.6
249A9598AA1 A100 $60 GO-1R 3.35 4002B5914ANP004 A1004 $190 G4-7KITS 3.34
249A9598AA2 A101 $60 GO-1R 1.22 4002B5914ANP004 A1004 $190 G4-7KITS 4.6
249A9598AA2 A101 $60 GO-1R 2.11 4002B5914ANP005 A1005 $246 G4-7KITS 3.34
249A9598AA2 A101 $60 GO-1R 3.35 4002B5914ANP005 A1005 $246 G4-7KITS 4.6
249A9598AA3 A102 $71 GO-1R 1.22 5BC42AB1729 D126 26 $1,901 GO-7PTC 7.9
249A9598AA3 A102 $71 GO-1R 2.11 5BC42AB1780 D141 29 $1,923 GO-7PTC 7.9
249A9598AA3 A102 $71 GO-1R 3.35 5BC42AB1830 D137 26 $1,901 GO-7PTC 7.9
249A9598AA4 A103 $71 GO-1R 1.22 5BC42AB1834 D136 25 $1,901 GO-7PTC 7.9
249A9598AA4 A103 $71 GO-1R 2.11 5BC42AB1882 D142 29 $1,923 GO-7PTC 7.9
249A9598AA4 A103 $71 GO-1R 3.35 5BC42AB2177 D143 30 $1,983 GO-7PTC 7.9
249A9598AA5 A104 $91 GO-1R 1.22 5BC42AB2195 D149 30 $1,983 GO-7PTC 7.9
249A9598AA5 A104 $91 GO-1R 2.11 5BC42AE1001 D268 38 $2,195 GO-7PTC 7.9
249A9598AA5 A104 $91 GO-1R 3.35 5BC42AE1002 D256 32 $2,182 GO-7PTC 7.9
249A9598AA6 A105 $91 GO-1R 1.22 5BC42AE1003 D255 32 $2,182 GO-7PTC 7.9
249A9598AA6 A105 $91 GO-1R 2.11 5BC42AE1008 D267 38 $2,195 GO-7PTC 7.9
249A9598AA6 A105 $91 GO-1R 3.35 5BC46AB1570 D127 36 $2,994 GO-7PTC 7.9
249A9598AA7 A106 $105 GO-1R 1.22 5BC46AB1571 D128 36 $2,994 GO-7PTC 7.9
249A9598AA7 A106 $105 GO-1R 2.11 5BC46AB1572 D138 29 $2,994 GO-7PTC 7.9
249A9598AA7 A106 $105 GO-1R 3.35 5BC46AB1581 D139 36 $3,026 GO-7PTC 7.9
249A9598AA8 A107 $105 GO-1R 1.22 5BC46AB1582 D140 36 $3,026 GO-7PTC 7.9
249A9598AA8 A107 $105 GO-1R 2.11 5BC46AB1590 D130 39 $3,013 GO-7PTC 7.9
249A9598AA8 A107 $105 GO-1R 3.35 5BC46AB1591 D131 39 $3,013 GO-7PTC 7.9
249A9598AA9 A108 $186 GO-1R 1.22 5BC46AB2014 D132 41 $3,103 GO-7PTC 7.9
249A9598AA9 A108 $186 GO-1R 2.11 5BC46AB2082 D133 41 $3,103 GO-7PTC 7.9
249A9598AA9 A108 $186 GO-1R 3.35 5BC46AB2291 D144 41 $3,103 GO-7PTC 7.9
36A167702BAG01 A648 $1,392 GO-2KITS 7.24 5BC48JB1059 D295 43 $510 GO-1GLF 8.6
36A167741CBG01 A687 $1,337 GO-2KITS 7.23 5BC48JB1061 D297 50 $718 GO-1GLF 8.6
36A167742ABG02 A688 $1,342 GO-2KITS 7.23 5BC48JB1062 D298 43 $718 GO-1GLF 8.6
36A167743CBG02 A689 $1,250 GO-2KITS 7.23 5BC49JB1115 D379 50 $738 GO-1GLF 8.6
36A167744ABG03 A690 $1,530 GO-2KITS 7.23 5BC49JB1155 D388 55 $840 GO-1GLF 8.6
36A167745GBG10 A691 $1,805 GO-2KITS 7.23 5BC49JB2048 D384 60 $987 GO-1GLF 8.6
36A167746GBG10 A692 $1,504 GO-2KITS 7.23 5BC49JB2049 D385 62 $964 GO-1GLF 8.6
36A167747GBG10 A693 $1,517 GO-2KITS 7.23 5BC49JB3071 D380 60 $919 GO-1GLF 8.6
36A167747GDG10 A694 $1,815 GO-2KITS 7.23 5BC58JBS6259 D294 38 $475 GO-1GLF 8.6
36A167749EBG34 A695 $3,024 GO-2KITS 7.23 5BC58JBS6334 D377 38 $511 GO-1GLF 8.6
36A167700AAG01 A641 $1,097 GO-2KITS 7.24 5BC58JBS6335 D378 38 $511 GO-1GLF 8.6
36A167700BAG01 A642 $978 GO-2KITS 7.24 5BC58JBS6337 D375 38 $465 GO-1GLF 8.6
36A167700CAG01 A643 $1,008 GO-2KITS 7.24 5BC58JBS6338 D376 50 $465 GO-1GLF 8.6
36A167701AAG01 A644 $1,204 GO-2KITS 7.24 5BC58JBS6339 D381 38 $465 GO-1GLF 8.6
36A167701BAG01 A645 $1,303 GO-2KITS 7.24 5BC58JBS6340 D383 35 $579 GO-1GLF 8.6
36A167701CAG01 A646 $1,303 GO-2KITS 7.24 5BC58JBS6341 D386 28 $579 GO-1GLF 8.6
36A167701CAG14 A686 $1,260 GO-2KITS 7.24 5BC58JBS6342 D382 40 $511 GO-1GLF 8.6
36A167702AAG01 A647 $2,382 GO-2KITS 7.24 5BC58JBS6344 D387 40 $590 GO-1GLF 8.6
36A167702BAG01 A648 $1,392 GO-2KITS 7.24 5BC59JBS6258 D296 41 $510 GO-1GLF 8.6
36A167702CAG01 A649 $2,604 GO-2KITS 7.24 5BCC56BD34 D111 23 $1,298 GO-1DC 7.11
36A167702DAG01 A650 $2,604 GO-2KITS 7.24 5BCC56CD10 D106 25 $1,388 GO-1DC 7.11
36A167802BAG02 A677 $202 GO-2KITS 7.24 5BCC56ED8 D107 28 $1,493 GO-1DC 7.11
36A167803BAG02 A678 $219 GO-2KITS 7.24 5BCC56KD6 D112 37 $1,673 GO-1DC 7.11
36A167804BAG02 A680 $269 GO-2KITS 7.24 5BCD56CD247 D115 24 $1,560 GO-1DC 7.6
36A167805BAG02 A682 $336 GO-2KITS 7.24 5BCD56ED307 D167 29 $1,628 GO-1DC 7.6
36A167806BAG01 A684 $353 GO-2KITS 7.24 5BCD56ND88 D116 41 $1,619 GO-1DC 7.6
36A167806BAG02 A683 $353 GO-2KITS 7.24 5BCD56ND91 D169 42 $1,853 GO-1DC 7.6
36A167809BAG01 A685 $386 GO-2KITS 7.24 5BCD56RD397 D117 52 $1,919 GO-1DC 7.6
36A172471AAG02 A670 $189 GO-2KITS 7.23 5BCD56RD398 D118 55 $1,838 GO-1DC 7.6
36A172472AAG01 A671 $425 GO-2KITS 7.23 5BCD56RD418 D135 55 $2,085 GO-1DC 7.6
36A172473AAG01 A672 $492 GO-2KITS 7.23 5BCJ56BD34 D113 23 $1,418 GO-1DC 7.11
36A172474AAG01 A674 $730 GO-2KITS 7.23 5BCJ56CD9 D109 26 $1,568 GO-1DC 7.11
36A172475AAG01 A676 $621 GO-2KITS 7.23 5BCJ56ED7 D110 31 $1,845 GO-1DC 7.11
4001A5202AAG001 PB14A $72 G4-7KITS 3.33 5BPA56HAG10 D351 19 $354 GO-1PM 8.7
4001A5202AAG002 PB18A $98 G4-7KITS 3.33 5BPA56HAG11 D273 19 $271 GO-1PM 7.6
4001A5202AAG003 PB21A $125 G4-7KITS 3.33 5BPA56HAG24 D360 19 $316 GO-1PM 7.10
4001A5202AAG004 PB25A $169 G4-7KITS 3.33 5BPA56HAG8 D283 19 $281 GO-1PM 7.6
4001A5202AAG005 PB28A $224 G4-7KITS 3.33 5BPA56HAG9 D350 19 $354 GO-1PM 8.7
4001A5921CYG001 A341 $68 G4-7KITS 3.34 5BPA56KAG10 D286 29 $321 GO-1PM 7.6
4001A5921CYG002 A342 $68 G4-7KITS 3.34 5BPA56KAG15 D352 25 $372 GO-1PM 8.7
4001A5921CYG006 A340 $68 G4-7KITS 3.34 5BPA56KAG16 D353 25 $372 GO-1PM 8.7

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.20 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5BPA56KAG17 D354 29 $420 GO-1PM 8.7 5CD144UC005B037 D413 128 $2,921 GO-2AS 7.7
5BPA56KAG18 D355 29 $420 GO-1PM 8.7 5CD144UC023B030 D414 128 $4,058 GO-2AS 7.7
Cross Reference Guide

5BPA56KAG19 D274 25 $376 GO-1PM 7.6 5CD145GA002B016 D415 165 $3,709 GO-2AS 7.5
5BPA56KAG20 D275 29 $336 GO-1PM 7.6 5CD145SA011B018 D408 165 $3,709 GO-2AS 7.5
5BPA56KAG21 D276 29 $379 GO-1PM 7.6 5CD145UA005B026 D417 162 $3,152 GO-2AS 7.2
5BPA56KAG42 D361 25 $338 GO-1PM 7.10 5CD145UA030B005 D418 172 $4,289 GO-2AS 7.4
5BPA56KAG43 D362 25 $325 GO-1PM 7.10 5CD145VC005B055 D419 160 $2,994 GO-2AS 7.7
5BPA56KAG8 D284 25 $331 GO-1PM 7.6 5CD145VE005B008 D555 160 $2,994 GO-2AS 7.7
5BPA56KAG9 D285 29 $331 GO-1PM 7.6 5CD145WA009B020 D583 162 $3,709 GO-2AS 7.7
5BPA56KBF10 D363 29 $356 GO-1PM 7.10 5CD145WC006B021 D420 160 $3,795 GO-2AS 7.7
5BPA56KBF11 D364 29 $343 GO-1PM 7.10 5CD152GA017B014 D421 234 $3,152 GO-2AS 7.2
5BPA56NAG10 D278 43 $494 GO-1PM 7.6 5CD152NC025B015 D422 243 $3,403 GO-2AS 7.2
5BPA56NAG11 D356 42 $511 GO-1PM 8.7 5CD153JA001B023 D423 252 $3,592 GO-2AS 7.2
5BPA56NAG12 D357 39 $511 GO-1PM 8.7 5CD153JA001B090 D561 272 $4,729 GO-2AS 7.4
5BPA56NAG6 D287 37 $332 GO-1PM 7.6 5CD153JA001B106 D424 252 $3,592 GO-2AS 7.3
5BPA56NAG7 D288 37 $345 GO-1PM 7.6 5CD153RA039B003 D425 252 $3,592 GO-2AS 7.2
5BPA56NAG9 D277 39 $430 GO-1PM 7.6 5CD153RA039B039 D426 252 $3,592 GO-2AS 7.3
5BPA56NBF27 D366 36 $433 GO-1PM 7.10 5CD153RC027B015 D427 252 $3,843 GO-2AS 7.2
5BPA56PBF25 D365 36 $461 GO-1PM 7.10 5CD153TC024B001 D428 261 $4,696 GO-2AS 7.7
5BPA56PBF26 D367 41 $599 GO-1PM 7.10 5CD154JA015B024 D685 280 $4,487 GO-2AS 7.5
5BPA56RAG10 D358 41 $634 GO-1PM 8.7 5CD154KA026B004 D429 287 $4,487 GO-2AS 7.5
5BPA56RAG11 D359 41 $634 GO-1PM 8.7 5CD154SA016B023 D683 280 $4,487 GO-2AS 7.5
5BPA56RAG4 D289 40 $442 GO-1PM 7.6 5CD154SA045B001 D684 280 $4,487 GO-2AS 7.5
5BPA56RAG5 D290 40 $442 GO-1PM 7.6 5CD154TA007B005 D430 287 $4,487 GO-2AS 7.5
5BPA56RAG8 D279 41 $624 GO-1PM 7.6 5CD154ZC801B803 D584 389 $5,831 GO-2AS 7.7
5BPA56RAG9 D280 41 $624 GO-1PM 7.6 5CD154ZC852B800 D431 289 $5,497 GO-2AS 7.7
5CD122HE001 D301 55 $1,062 GO-2SK3 7.6 5CD163KA009A133 D432 361 $4,321 GO-2AS 7.2
5CD122NE001 D300 55 $1,038 GO-2SK3 7.6 5CD163KA009A134 D433 361 $4,321 GO-2AS 7.3
5CD122NP001 D311 67 $1,439 GO-2PK3 7.6 5CD163KA009A136 D562 381 $5,458 GO-2AS 7.4
5CD123GE001 D302 67 $1,242 GO-2SK3 7.6 5CD163SA026A070 D434 361 $4,321 GO-2AS 7.2
5CD123GP001 D313 77 $1,448 GO-2PK3 7.6 5CD163SC035A010 D435 378 $4,572 GO-2AS 7.2
5CD123PE001 D304 67 $1,277 GO-2SK3 7.6 5CD164LA014A031 D436 442 $5,123 GO-2AS 7.5
5CD123PP001 D315 79 $1,208 GO-2PK3 7.6 5CD164LA041A026 D686 403 $5,446 GO-2AS 7.5
5CD123UE001 D303 59 $1,255 GO-2SK3 7.6 5CD164MA012A076 D563 423 $6,092 GO-2AS 7.4
5CD123UE002 D306 67 $1,505 GO-2SK3 7.6 5CD164MA012A136 D437 403 $4,955 GO-2AS 7.2
5CD123UP001 D314 59 $1,448 GO-2PK3 7.6 5CD164MA012A137 D438 403 $4,955 GO-2AS 7.3
5CD123UP002 D317 78 $1,448 GO-2PK3 7.6 5CD164MA038A028 D439 403 $4,955 GO-2AS 7.3
5CD124TE001 D307 77 $1,529 GO-2SK3 7.6 5CD164TA009A034 D440 442 $5,123 GO-2AS 7.5
5CD124TP001 D318 88 $1,401 GO-2PK3 7.6 5CD164UA023A109 D441 403 $4,955 GO-2AS 7.2
5CD125TE001 D305 93 $1,619 GO-2SK3 7.6 5CD173NA010A114 D442 493 $6,118 GO-2AS 7.2
5CD125TE002 D308 102 $1,938 GO-2SK3 7.6 5CD173NA010A130 D564 513 $6,864 GO-2AS 7.4
5CD125TP001 D316 113 $1,802 GO-2PK3 7.6 5CD173VA018A079 D444 493 $6,118 GO-2AS 7.2
5CD125TP002 D319 113 $1,956 GO-2PK3 7.6 5CD174NA005A080 D569 587 $6,611 GO-2AS 7.5
5CD125WE001 D310 102 $1,962 GO-2SK3 7.6 5CD174RA009A141 D565 576 $7,424 GO-2AS 7.4
5CD125WP001 D321 115 $1,913 GO-2PK3 7.6 5CD174RA009A197 D445 548 $6,734 GO-2AS 7.2
5CD125YE001 D309 102 $1,938 GO-2SK3 7.6 5CD174RA009A257 D446 548 $6,136 GO-2AS 7.3
5CD125YP001 D320 113 $1,956 GO-2PK3 7.6 5CD174VA019A060 D568 587 $6,611 GO-2AS 7.5
5CD142AA036B008 D680 83 $2,221 GO-2AS 7.5 5CD174WA020A089 D448 548 $6,734 GO-2AS 7.2
5CD142DA036B024 D681 83 $2,073 GO-2AS 7.5 5CD183MA033B020 D650 752 $7,397 GO-2AS 7.4
5CD142EA019B017 D587 83 $1,804 GO-2AS 7.2 5CD183SA043B017 D566 752 $8,649 GO-2AS 7.4
5CD142FC008B054 D400 80 $2,649 GO-2AS 7.7 5CD183SA043B052 D548 691 $7,216 GO-2AS 7.3
5CD142FE012B025 D401 80 $2,649 GO-2AS 7.7 5CD183WA043B006 D570 732 $7,594 GO-2AS 7.5
5CD142GA010B034 D585 83 $2,598 GO-2AS 7.7 5CD184NA054B019 D651 830 $8,440 GO-2AS 7.4
5CD142GE011B020 D402 80 $2,684 GO-2AS 7.7 5CD184PA021B018 D609 769 $9,187 GO-2AS 7.3
5CD142GE011B039 D536 80 $2,795 GO-2AS 7.7 5CD184TA094B068 D449 769 $9,049 GO-2AS 7.2
5CD143BA012B038 D588 105 $2,124 GO-2AS 7.2 5CD184TA094B069 D451 769 $8,240 GO-2AS 7.3
5CD143JA014B026 D403 105 $2,124 GO-2AS 7.2 5CD184TA094B070 D450 769 $9,049 GO-2AS 7.2
5CD143JC014B012 D404 102 $2,210 GO-2AS 7.2 5CD184TA094B071 D541 769 $7,922 GO-2AS 7.2
5CD143LC007B034 D540 102 $2,784 GO-2AS 7.7 5CD184TA094B075 D542 769 $7,922 GO-2AS 7.2
5CD143LE007B021 D405 102 $2,784 GO-2AS 7.7 5CD184TA094B076 D567 830 $9,673 GO-2AS 7.4
5CD143MC003B018 D539 102 $2,824 GO-2AS 7.7 5CD184VA085B006 D589 769 $7,950 GO-2AS 7.2
5CD143MC003B040 D537 102 $2,906 GO-2AS 7.7 5CD184YA064B004 D572 812 $8,893 GO-2AS 7.5
5CD143ME003B021 D406 102 $2,906 GO-2AS 7.7 5CD185SA001B012 D610 888 $10,577 GO-2AS 7.3
5CD143UA022B010 D586 105 $2,631 GO-2AS 7.7 5CD185VA012B001 D579 949 $12,510 GO-2AS 7.4
5CD144EC002B052 D682 128 $3,282 GO-2AS 7.5 5CD185VA012B002 D655 949 $12,510 GO-2AS 7.4
5CD144FA002B020 D407 128 $2,612 GO-2AS 7.2 5CD185VA012B003 D577 888 $11,077 GO-2AS 7.3
5CD144MA020B038 D553 128 $2,193 GO-2AS 7.5 5CD185VA811B802 D576 769 $9,430 GO-2AS 7.3
5CD144MA020B073 D530 128 $2,809 GO-2AS 7.5 5CD185VA811B803 D578 830 $10,863 GO-2AS 7.4
5CD144PA002B055 D409 128 $2,612 GO-2AS 7.2 5CD192NA027A136 D652 815 $12,510 GO-2AS 7.4
5CD144PC016B013 D410 128 $2,698 GO-2AS 7.2 5CD193MA038A053 D453 860 $10,542 GO-2AS 7.2
5CD144SC003B063 D411 128 $2,857 GO-2AS 7.7 5CD193PA065A129 D455 860 $12,169 GO-2AS 7.2
5CD144SE005B028 D412 128 $2,857 GO-2AS 7.7 5CD193PA065A140 D456 860 $12,169 GO-2AS 7.2

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.21
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5CD193PA065A160 D544 860 $10,358 GO-2AS 7.2 5K511EN2307MRA2 S3408 4710 $31,883 G6-7DAN 5.2
5CD193PA084A037 D457 940 $9,844 GO-2AS 7.5 5KAF143SAA2151 S2053 43 $724 G4-7AS 4.2

Cross Reference Guide

5CD193PA094A243 D656 925 $15,471 GO-2AS 7.4 5KAF143SAB2174 M9300 43 4.8
5CD193PA094A244 D657 925 $15,471 GO-2AS 7.4 5KAF145SAA2151 S2054 43 $780 G4-7AS 4.2
5CD193TA027A007 D460 940 $9,844 GO-2AS 7.5 5KAF145SAB2165 M9301 43 4.8
5CD194NA067A051 D462 1020 $13,872 GO-2AS 7.2 5KAF182SAA2151 S2055 76 $980 G4-7AS 4.2
5CD194NA067A052 D543 1020 $12,140 GO-2AS 7.2 5KAF182SAB2207 M9302 76 4.8
5CD194RA060A028 D463 1100 $12,421 GO-2AS 7.5 5KAF184SAA2151 S2056 101 $1,095 G4-7AS 4.2
5CD194SA081A067 D465 1020 $15,266 GO-2AS 7.2 5KAF184SAB2205 M9303 101 4.8
5CD194SA081A129 D466 1020 $15,266 GO-2AS 7.2 5KAF213SAA2151 S2057 200 $1,281 G4-7AS 4.2
5CD194SA082A247 D558 1020 $13,892 GO-2AS 7.3 5KAF213SAB2216 M9304 200 4.8
5CD194SA082A315 D468 1085 $18,029 GO-2AS 7.4 5KAF215SAA2151 S2058 220 $1,531 G4-7AS 4.2
5CD194SA082A418 D467 1085 $15,471 GO-2AS 7.4 5KAF215SAB2210 M9305 220 4.8
5CD194SA082A419 D559 1020 $16,450 GO-2AS 7.3 5KAF254SAA2151 S2059 315 $1,844 G4-7AS 4.2
5CD194SA109A051 D611 1020 $16,514 GO-2AS 7.3 5KAF254SAB2215 M9306 315 4.8
5CD194SA109A072 D612 1020 $16,514 GO-2AS 7.3 5KAF256SAA2151 S2060 350 $2,040 G4-7AS 4.2
5CD194UA035A008 D469 1100 $12,421 GO-2AS 7.5 5KAF256SAB2196 M9307 350 4.8
5CD194XA002A073 D654 1085 $13,516 GO-2AS 7.4 5KAF284SAA2151 S2061 460 $2,548 G4-7AS 4.2
5CD194XA002A092 D658 1085 $15,782 GO-2AS 7.4 5KAF284SAB2183 M9308 460 4.8
5CD203LA057A013 D590 1300 $16,900 GO-2AS 7.2 5KAF286SAA2151 S2062 510 $2,913 G4-7AS 4.2
5CD203NA039A054 D659 1365 $18,933 GO-2AS 7.4 5KAF286SAB2182 M9309 510 4.8
5CD203PA088A032 D471 1300 $18,079 GO-2AS 7.2 5KAF324SAA2222 M9310 690 4.8
5CD203PA097A176 D473 1365 $20,513 GO-2AS 7.4 5KAF324SS2150D20P S2063 690 $3,772 G4-7AS 4.2
5CD203PA097A225 D560 1300 $18,934 GO-2AS 7.3 5KAF326SAA222 M9311 740 4.8
5CD203PA108A033 D614 1300 $20,183 GO-2AS 7.3 5KAF326SS2150D20P S2064 740 $4,666 G4-7AS 4.2
5CD203PA108A034 D592 1300 $20,183 GO-2AS 7.3 5KAF364SAA222 M9312 1040 4.8
5CD204NA044A093 D660 1665 $21,917 GO-2AS 7.4 5KAF364SAA223 M9313 1060 4.8
5CD204PA086A041 D474 1680 $18,104 GO-2AS 7.5 5KAF364SS2019D20P S2073 1060 $6,600 G4-7AS 4.2
5CD204PA086A042 D554 1680 $14,951 GO-2AS 7.5 5KAF364SS2150D20P S2065 1040 $6,014 G4-7AS 4.2
5CD204PA107A104 D661 1665 $21,917 GO-2AS 7.4 5KAF365SAA223 M9314 1070 4.8
5CD204PA107A141 D662 1665 $25,236 GO-2AS 7.4 5KAF365SAA224 M9315 1070 4.8
5CD204RA068A048 D476 1600 $21,751 GO-2AS 7.2 5KAF365SS2044D20P S2074 1070 $7,890 G4-7AS 4.2
5CD204RA068A049 D477 1600 $21,751 GO-2AS 7.2 5KAF365SS2150D20P S2066 1070 $6,813 G4-7AS 4.2
5CD204SA038A260 D663 1720 $25,863 GO-2AS 7.4 5KAF405SAA220 M9317 1560 4.8
5CD204SA038A261 D478 1720 $25,863 GO-2AS 7.4 5KAF405SAA221 M9316 1560 4.8
5CD204SA038A265 D574 1650 $24,010 GO-2AS 7.3 5KAF405SAA221 M9319 1560 4.8
5CD204SA046A024 D616 1650 $25,259 GO-2AS 7.3 5KAF405SS2038P S2075 1560 $11,014 G4-7AS 4.2
5CD204SA046A025 D593 1650 $25,259 GO-2AS 7.3 5KAF405SS2039P S2076 1560 $13,890 G4-7AS 4.2
5CD222PA076B030 D480 1900 $27,588 GO-2AS 7.2 5KAF405SS2150P S2067 1560 $9,219 G4-7AS 4.2
5CD222YA001B096 D664 1982 $31,371 GO-2AS 7.4 5KAF444SAA220 M9318 2050 4.8
5CD222YA001B098 D482 1982 $31,371 GO-2AS 7.4 5KAF444SS2150P S2068 2050 $11,988 G4-7AS 4.2
5CD222YA001B125 D575 1900 $29,518 GO-2AS 7.3 5KAF445SAA220 M9320 2050 4.8
5CD222YA006B022 D594 1900 $30,767 GO-2AS 7.3 5KAF445SAA220 M9322 2050 4.8
5CD222YA006B023 D617 1900 $30,767 GO-2AS 7.3 5KAF445SAA221 M9321 2050 4.8
5CD223MA051B038 D613 290 $23,807 GO-2AS 7.3 5KAF445SAA221 M9323 2050 4.8
5CD223NA048B024 D615 2290 $26,933 GO-2AS 7.3 5KAF445SS2033P S2077 2050 $15,765 G4-7AS 4.2
5CD223PA097B025 D618 2290 $34,750 GO-2AS 7.3 5KAF445SS2034P S2078 2050 $18,666 G4-7AS 4.2
5CD223SA074B132 D486 2290 $40,675 GO-2DS 7.2 5KAF445SS2150P S2069 2050 $13,863 G4-7AS 4.2
5CD223SA074B133 D547 2290 $33,922 GO-2AS 7.2 5KAF445SS2151P S2070 2050 $16,764 G4-7AS 4.2
5CD224RA090B076 D619 2810 $40,757 GO-2DS 7.3 5KAF449SAA221 M9324 2830 4.8
5CD224TA033B079 D489 2810 $49,160 GO-2DS 7.3 5KAF449SAA222 M9325 2870 4.8
5CD226AA002B024 D620 4260 $65,720 GO-2DS 7.3 5KAF449SAA223 M9326 3110 4.8
5CD226SA002B052 D490 4343 $48,107 GO-2DS 7.4 5KAF449SAA224 M9327 2890 4.8
5CD226TA001B048 D492 4343 $60,809 GO-2DS 7.4 5KAF449SS2028P S2079 2870 $23,417 G4-7AS 4.2
5CD604KA002C008 D600 5743 $76,964 GO-2DS 7.4 5KAF449SS2029P S2080 2890 $26,337 G4-7AS 4.2
5CD604LA001C015 D601 6043 $99,367 GO-2DS 7.4 5KAF449SS2150P S2071 2830 $20,917 G4-7AS 4.2
5K509EN1304M S3409 3620 $36,346 G6-7DAN 5.2 5KAF449SSH2150P S2072 3110 $23,837 G4-7AS 4.2
5K509EN1304MRA1 S3406 3620 $33,137 G6-7DAN 5.2 5KC143BC201 F835 48 $350 G4-7FAZ 8.5
5K509EN1304MRA2 S3404 3620 $31,489 G6-7DAN 5.2 5KC145BC201 F836 65 $365 G4-7FAZ 8.5
5K509EN1304MRA3 S3402 3620 $29,811 G6-7DAN 5.2 5KC182BC213 F786 77 $495 G4-7FAZ 8.5
5K509EN1328M S3428 3620 $38,346 G6-7DAN 5.2 5KC182BC214 F787 79 $476 G4-7FAZ 8.5
5K509EN1328MRA1 S3427 3620 $35,137 G6-7DAN 5.2 5KC184BC214 F789 95 $518 G4-7FAZ 8.5
5K509EN1328MRA2 S3426 3620 $33,489 G6-7DAN 5.2 5KC184BC217 F788 92 $561 G4-7FAZ 8.5
5K509EN1328MRA3 S3425 3620 $31,811 G6-7DAN 5.2 5KC184BC218 F790 103 $665 G4-7FAZ 8.5
5K509EN2771M S3407 3620 $30,880 G6-7DAN 5.2 5KC184BC219 F792 103 $601 G4-7FAZ 8.5
5K509EN2771MRA1 S3405 3620 $29,809 G6-7DAN 5.2 5KC215BC214 F791 143 $765 G4-7FAZ 8.5
5K509EN2771MRA2 S3403 3620 $28,657 G6-7DAN 5.2 5KC215BC215 F793 178 $1,000 G4-7FAZ 8.5
5K511EN1081M S3431 4540 $45,375 G6-7DAN 5.2 5KC215BC217 F795 183 $1,200 G4-7FAZ 8.5
5K511EN1081MRA1 S3430 4540 $42,315 G6-7DAN 5.2 5KC215BC218 F798 178 $1,000 G4-7FAZ 8.5
5K511EN1081MRA2 S3429 4540 $41,008 G6-7DAN 5.2 5KC215BC219 F794 183 $1,200 G4-7FAZ 8.5
5K511EN2307M S3413 4710 $35,805 G6-7DAN 5.2 5KC56BC201 F837 42 $267 G4-7FAZ 8.5
5K511EN2307MRA1 S3411 4710 $33,932 G6-7DAN 5.2 5KE143AC204 S2801 49 $220 GO-7DEZ 1.2

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.22 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KE143AC205 S2802 49 $220 G4-7DEZ 1.2 5KE184ATF105 S3617 93 $725 G4-7DEF 6.12
5KE143BC105 S210 53 $282 G4-7TEZ 1.8 5KE184ATF205 S3601 104 $585 G4-7DEF 6.12
Cross Reference Guide

5KE143BC204 S2790 53 $250 GO-7TEZ 1.8 5KE184BC104 S222 106 $442 G4-7TEZ 1.8
5KE143BC205 S211 53 $243 G4-7TEZ 1.8 5KE184BC105 S227 106 $442 G4-7TEZ 1.8
5KE143BC305 S212 55 $315 G4-7TEZ 1.8 5KE184BC204 S223 114 $380 G4-7TEZ 1.8
5KE143BTE105 S4210 50 $282 G4-7TEZ 1.8 5KE184BC205 S225 115 $380 G4-7TEZ 1.8
5KE143BTE205 S4211 50 $243 G4-7TEZ 1.8 5KE184BC206 S224 114 $380 G4-7TEZ 1.8
5KE143FC205 S209 53 $385 G4-7TECZ 1.12 5KE184BC305 S226 101 $375 G4-7TEZ 1.8
5KE143KC105 S2210 53 $328 G4-7TECZ 1.12 5KE184BTE105 S4227 92 $442 G4-7TEZ 1.8
5KE143KC205 S2211 53 $288 G4-7TECZ 1.12 5KE184BTE205 S4225 95 $380 G4-7TEZ 1.8
5KE143KTE105 S5210 15 $328 G4-7TECZ 1.12 5KE184CC105 S2610 121 $797 G5-7XPZ 1.18
5KE143KTE205 S5211 50 $288 G4-7TECZ 1.12 5KE184CC205 S2611 123 $732 G5-7XPZ 1.18
5KE145AC104 S2803 62 $332 G4-7DEZ 1.2 5KE184CC305 S2603 112 $725 G5-7XPZ 1.18
5KE145AC105 S2804 62 $332 GO-7DEZ 1.2 5KE184FC205 S271 114 $539 G4-7TECZ 1.12
5KE145AC201 S2805 57 $245 GO-7DEZ 1.2 5KE184KC105 S2227 106 $498 G4-7TECZ 1.12
5KE145AC202 S2806 57 $245 G4-7DEZ 1.2 5KE184KC107 S2949 106 $595 G4-7TEZ 6.16
5KE145AC204 S2807 59 $260 GO-7DEZ 1.2 5KE184KC205 S2225 114 $436 G4-7TECZ 1.12
5KE145AC205 S2808 59 $260 G4-7DEZ 1.2 5KE184KTE105 S5227 92 $498 G4-7TECZ 1.12
5KE145ATE105 S4804 52 $332 G4-7DEZ 1.2 5KE184KTE205 S5225 95 $436 G4-7TECZ 1.12
5KE145BC105 S213 57 $321 G4-7TEZ 1.8 5KE213AC104 S2517 156 $630 G4-7DEZ 1.2
5KE145BC202 S214 57 $262 G4-7TEZ 1.8 5KE213AC105 S2516 156 $630 G4-7DEZ 1.2
5KE145BC204 S2791 57 $200 G4-7TEZ 1.8 5KE213AC204 S2519 152 $475 G4-7DEZ 1.2
5KE145BC205 S215 57 $282 G4-7TEZ 1.8 5KE213AC205 S2518 152 $475 G4-7DEZ 1.2
5KE145BC207 S2793 57 $290 G4-7TEZ 1.8 5KE213AC206 S2520 152 $475 G4-7DEZ 1.2
5KE145BC305 S216 59 $315 G4-7TEZ 1.8 5KE213AC304 S2508 132 $450 G4-7DEZ 1.2
5KE145BTE105 S4202 52 $321 G4-7TEZ 1.8 5KE213AC305 S2507 132 $450 G4-7DEZ 1.2
5KE145BTE202 S4214 56 $262 G4-7TEZ 1.8 5KE213ATE105 S4516 133 $630 G4-7DEZ 1.2
5KE145BTE205 S4215 56 $282 G4-7TEZ 1.8 5KE213ATE205 S4518 137 $475 G4-7DEZ 1.2
5KE145FC202 S268 57 $405 G4-7TECZ 1.12 5KE213ATF105 S3618 128 $890 G4-7DEF 6.12
5KE145FC205 S269 57 $425 G4-7TECZ 1.12 5KE213ATF205 S3602 128 $719 G4-7DEF 6.12
5KE145KC105 S2213 62 $368 G4-7TECZ 1.12 5KE213BC104 S228 156 $576 G4-7TEZ 1.9
5KE145KC202 S2214 62 $308 G4-7TECZ 1.12 5KE213BC105 S229 156 $576 G4-7TEZ 1.9
5KE145KC205 S2215 62 $328 G4-7TECZ 1.12 5KE213BC204 S230 167 $510 G4-7TEZ 1.9
5KE145KC305 S2216 62 $378 G4-7TECZ 1.12 5KE213BC205 S231 167 $510 G4-7TEZ 1.9
5KE145KTE105 S5213 52 $368 G4-7TECZ 1.12 5KE213BC206 S232 167 $510 G4-7TEZ 1.9
5KE145KTE202 S5214 56 $308 G4-7TECZ 1.12 5KE213BC304 S233 139 $497 G4-7TEZ 1.8
5KE145KTE205 S5215 56 $328 G4-7TECZ 1.12 5KE213BC305 S234 139 $497 G4-7TEZ 1.8
5KE145KTE305 S5216 56 $378 G4-7TECZ 1.12 5KE213BTE105 S4229 138 $576 G4-7TEZ 1.9
5KE182AC104 S2552 88 $402 G4-7DEZ 1.2 5KE213BTE205 S4231 140 $510 G4-7TEZ 1.9
5KE182AC105 S2503 88 $403 G4-7DEZ 1.2 5KE213CC105 S2615 189 $937 G5-7XPZ 1.18
5KE182AC204 S2505 81 $287 G4-7DEZ 1.2 5KE213CC205 S2616 187 $932 G5-7XPZ 1.18
5KE182AC205 S2504 81 $288 G4-7DEZ 1.2 5KE213CC305 S2608 185 $856 G5-7XPZ 1.18
5KE182AC206 S2506 81 $287 G4-7DEZ 1.2 5KE213DTT5002 V3109 220 $1,008 G5-7VHSB 6.2
5KE182AC305 S2501 88 $315 G4-7DEZ 1.2 5KE213DTT5003 V3108 220 $1,086 G5-7VHSB 6.2
5KE182ATE105 S4503 85 $403 G4-7DEZ 1.2 5KE213DTT5005 V3107 220 $1,174 G5-7VHSB 6.2
5KE182ATE205 S4504 91 $288 G4-7DEZ 1.2 5KE213DTT6002 V3116 220 $998 G5-7VHSB 6.2
5KE182ATF105 S3616 73 $605 G4-7DEF 6.12 5KE213DTT6005 V3115 220 $1,030 G5-7VHSB 6.2
5KE182BC104 S2792 90 $357 GO-7TEZ 1.8 5KE213FC205 S272 167 $684 G4-7TECZ 1.12
5KE182BC105 S221 90 $357 G4-7TEZ 1.8 5KE213KC105 S2229 156 $643 G4-7TECZ 1.12
5KE182BC204 S217 95 $320 G4-7TEZ 1.8 5KE213KC107 S2950 156 $743 G4-7TEZ 6.16
5KE182BC205 S219 95 $320 G4-7TEZ 1.8 5KE213KC205 S2231 167 $577 G4-7TECZ 1.12
5KE182BC206 S218 95 $320 G4-7TEZ 1.8 5KE213KTE105 S5229 138 $643 G4-7TECZ 1.12
5KE182BC305 S220 90 $339 G4-7TEZ 1.8 5KE213KTE205 S5231 140 $577 G4-7TECZ 1.12
5KE182BTE105 S4221 78 $357 G4-7TEZ 1.8 5KE215AC104 S2524 180 $806 G4-7DEZ 1.3
5KE182BTE205 S4219 80 $320 G4-7TEZ 1.8 5KE215AC105 S2523 180 $807 G4-7DEZ 1.3
5KE182CC105 S2605 101 $686 G5-7XPZ 1.18 5KE215AC204 S2526 180 $590 G4-7DEZ 1.2
5KE182CC205 S2606 106 $657 G5-7XPZ 1.18 5KE215AC205 S2525 180 $590 G4-7DEZ 1.2
5KE182CC305 S2601 97 $672 G5-7XPZ 1.18 5KE215AC206 S2527 180 $590 G4-7DEZ 1.2
5KE182FC205 S270 95 $479 G4-7TECZ 1.12 5KE215AC304 S2515 158 $620 G4-7DEZ 1.2
5KE182KC105 S2221 95 $413 G4-7TECZ 1.12 5KE215AC305 S2514 158 $620 G4-7DEZ 1.2
5KE182KC107 S2948 98 $481 G4-7TEZ 6.16 5KE215ATE105 S4523 160 $807 G4-7DEZ 1.3
5KE182KC205 S2219 95 $376 G4-7TECZ 1.12 5KE215ATE205 S4525 163 $590 G4-7DEZ 1.2
5KE182KTE105 S5221 78 $413 G4-7TECZ 1.12 5KE215ATF105 S3619 157 $1,050 G4-7DEF 6.12
5KE182KTE205 S5219 80 $376 G4-7TECZ 1.12 5KE215ATF205 S3603 180 $855 G4-7DEF 6.12
5KE184AC104 S2510 101 $480 G4-7DEZ 1.2 5KE215BC104 S235 183 $677 G4-7TEZ 1.9
5KE184AC105 S2509 101 $480 G4-7DEZ 1.2 5KE215BC105 S236 183 $677 G4-7TEZ 1.9
5KE184AC204 S2512 99 $348 G4-7DEZ 1.2 5KE215BC204 S237 189 $630 G4-7TEZ 1.9
5KE184AC205 S2511 99 $348 G4-7DEZ 1.2 5KE215BC205 S238 189 $630 G4-7TEZ 1.9
5KE184AC206 S2513 99 $348 G4-7DEZ 1.2 5KE215BC206 S239 189 $630 G4-7TEZ 1.9
5KE184AC305 S2502 97 $332 G4-7DEZ 1.2 5KE215BC304 S240 165 $716 G4-7TEZ 1.8
5KE184ATE105 S4509 93 $480 G4-7DEZ 1.2 5KE215BC305 S241 165 $716 G4-7TEZ 1.8
5KE184ATE205 S4511 93 $348 G4-7DEZ 1.2 5KE215BTE105 S4236 146 $677 G4-7TEZ 1.9

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.23
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KE215BTE205 S4238 152 $630 G4-7TEZ 1.9 5KE256FC205 S275 332 $1,395 G4-7TECZ 1.12
5KE215CC105 S2620 213 $1,096 G5-7XPZ 1.18 5KE256KC105 S2250 315 $1,272 G4-7TECZ 1.12

Cross Reference Guide

5KE215CC205 S2621 216 $1,076 G5-7XPZ 1.18 5KE256KC107 S2953 315 $1,473 G4-7TEZ 6.16
5KE215CC305 S2613 216 $1,110 G5-7XPZ 1.18 5KE256KC205 S2252 332 $1,277 G4-7TECZ 1.12
5KE215DTT5005 V3139 220 $1,380 G5-7VHSB 6.2 5KE256KTE105 S5250 325 $1,272 G4-7TECZ 1.12
5KE215DTT6005 V3141 220 $1,174 G5-7VHSB 6.2 5KE256KTE205 S5252 290 $1,277 G4-7TECZ 1.12
5KE215FC205 S273 189 $804 G4-7TECZ 1.12 5KE284AC115 S2543 370 $1,396 GO-7DEZ 1.3
5KE215KC105 S2236 183 $744 G4-7TECZ 1.12 5KE284AC204 S2545 352 $1,155 G4-7DEZ 1.3
5KE215KC107 S2951 183 $878 G4-7TEZ 6.16 5KE284AC205 S2544 352 $1,155 G4-7DEZ 1.3
5KE215KC205 S2238 189 $697 G4-7TECZ 1.12 5KE284AC304 S2536 343 $1,285 GO-7DEZ 1.3
5KE215KTE105 S5236 146 $744 G4-7TECZ 1.12 5KE284AC305 S2535 343 $1,285 GO-7DEZ 1.3
5KE215KTE205 S5238 152 $697 G4-7TECZ 1.12 5KE284ATE115 S4543 390 $1,396 G4-7DEZ 1.3
5KE254AC104 S2531 233 $970 G4-7DEZ 1.3 5KE284ATE205 S4544 370 $1,155 G4-7DEZ 1.3
5KE254AC105 S2530 233 $971 G4-7DEZ 1.3 5KE284ATF105 S3622 378 $1,660 G4-7DEF 6.12
5KE254AC204 S2533 246 $815 G4-7DEZ 1.3 5KE284ATF205 S3606 394 $1,491 G4-7DEF 6.12
5KE254AC205 S2532 246 $815 G4-7DEZ 1.3 5KE284BC115 S256 418 $1,432 G4-7TEZ 1.10
5KE254AC206 S2534 246 $815 G4-7DEZ 1.3 5KE284BC204 S257 429 $1,366 G4-7TEZ 1.10
5KE254AC304 S2522 211 $790 G4-7DEZ 1.2 5KE284BC205 S258 429 $1,366 G4-7TEZ 1.10
5KE254AC305 S2521 211 $790 G4-7DEZ 1.2 5KE284BC206 S259 429 $1,366 G4-7TEZ 1.10
5KE254ATE105 S4530 240 $971 G4-7DEZ 1.3 5KE284BC304 S260 414 $1,594 G4-7TEZ 1.9
5KE254ATE205 S4532 240 $815 G4-7DEZ 1.3 5KE284BC305 S261 414 $1,594 G4-7TEZ 1.9
5KE254ATF105 S3620 260 $1,275 G4-7DEF 6.12 5KE284BTE115 S4256 425 $1,432 G4-7TEZ 1.10
5KE254ATF205 S3604 260 $1,045 G4-7DEF 6.12 5KE284BTE205 S4258 430 $1,366 G4-7TEZ 1.10
5KE254BC104 S242 282 $888 G4-7TEZ 1.9 5KE284CC115 S2635 464 $2,182 G5-7XPZ 1.18
5KE254BC105 S243 282 $888 G4-7TEZ 1.9 5KE284CC205 S2636 488 $2,104 G5-7XPZ 1.18
5KE254BC204 S244 288 $908 G4-7TEZ 1.9 5KE284CC305 S2628 436 $2,345 G5-7XPZ 1.18
5KE254BC205 S245 288 $881 G4-7TEZ 1.9 5KE284DTT5005 V3188 507 $1,770 G5-7VHSB 6.2
5KE254BC206 S246 288 $881 G4-7TEZ 1.9 5KE284DTT6001 V3190 507 $1,832 G5-7VHSB 6.2
5KE254BC304 S247 257 $945 G4-7TEZ 1.9 5KE284DTT6005 V3189 507 $1,832 G5-7VHSB 6.2
5KE254BC305 S248 257 $945 G4-7TEZ 1.9 5KE284DTT7005 V3191 507 $1,934 G5-7VHSB 6.2
5KE254BTE105 S4243 290 $888 G4-7TEZ 1.9 5KE284FC205 S276 429 $1,703 G4-7TECZ 1.13
5KE254BTE205 S4245 260 $881 G4-7TEZ 1.9 5KE284KC115 S2256 418 $1,593 G4-7TECZ 1.13
5KE254CC105 S2625 330 $1,466 G5-7XPZ 1.18 5KE284KC117 S2954 418 $2,114 G4-7TEZ 6.16
5KE254CC205 S2626 339 $1,446 G5-7XPZ 1.18 5KE284KC205 S2258 429 $1,570 G4-7TECZ 1.13
5KE254CC305 S2618 308 $1,501 G5-7XPZ 1.18 5KE284KTE115 S5256 430 $1,593 G4-7TECZ 1.13
5KE254DTT5005 V3157 340 $1,515 G5-7VHSB 6.2 5KE284KTE205 S5258 430 $1,570 G4-7TECZ 1.13
5KE254DTT6005 V3158 340 $1,419 G5-7VHSB 6.2 5KE286AC115 S2547 440 $1,791 G4-7DEZ 1.3
5KE254FC205 S274 288 $1,127 G4-7TECZ 1.12 5KE286AC204 S2550 407 $1,325 G4-7DEZ 1.3
5KE254KC105 S2243 282 $1,016 G4-7TECZ 1.12 5KE286AC205 S2549 407 $1,325 G4-7DEZ 1.3
5KE254KC107 S2952 282 $1,132 G4-7TEZ 6.16 5KE286AC305 S2542 392 $1,625 GO-7DEZ 1.3
5KE254KC205 S2245 288 $1,009 G4-7TECZ 1.12 5KE286ATE115 S4547 410 $1,791 G4-7DEZ 1.3
5KE254KTE105 S5243 290 $1,016 G4-7TECZ 1.12 5KE286ATE205 S4549 400 $1,325 G4-7DEZ 1.3
5KE254KTE205 S5245 260 $1,009 G4-7TECZ 1.12 5KE286ATF105 S3623 406 $1,950 G4-7DEF 6.12
5KE256AC104 S2538 282 $1,185 G4-7DEZ 1.3 5KE286ATF205 S3607 436 $1,655 G4-7DEF 6.12
5KE256AC105 S2537 282 $1,186 G4-7DEZ 1.3 5KE286BC115 S262 455 $1,666 G4-7TEZ 1.10
5KE256AC204 S2540 277 $1,033 G4-7DEZ 1.3 5KE286BC116 S263 455 $1,666 G4-7TEZ 1.10
5KE256AC205 S2539 277 $1,033 G4-7DEZ 1.3 5KE286BC204 S264 475 $1,547 G4-7TEZ 1.10
5KE256AC206 S2541 277 $1,033 G4-7DEZ 1.3 5KE286BC205 S265 475 $1,547 G4-7TEZ 1.10
5KE256AC304 S2529 260 $945 GO-7DEZ 1.2 5KE286BC206 S266 475 $1,547 G4-7TEZ 1.10
5KE256AC305 S2528 260 $945 G4-7DEZ 1.2 5KE286BC305 S267 473 $1,881 G4-7TEZ 1.9
5KE256ATE105 S4537 307 $1,186 G4-7DEZ 1.3 5KE286BTE115 S4262 465 $1,666 G4-7TEZ 1.10
5KE256ATE205 S4539 307 $1,033 G4-7DEZ 1.3 5KE286BTE205 S4265 455 $1,547 G4-7TEZ 1.10
5KE256ATF105 S3621 307 $1,483 G4-7DEF 6.12 5KE286CC115 S2640 502 $2,471 G5-7XPZ 1.18
5KE256ATF205 S3605 310 $1,271 G4-7DEF 6.12 5KE286CC205 S2641 570 $2,372 G5-7XPZ 1.18
5KE256BC104 S249 315 $1,136 G4-7TEZ 1.9 5KE286CC305 S2633 517 $2,758 G5-7XPZ 1.18
5KE256BC105 S250 315 $1,136 G4-7TEZ 1.9 5KE286DTT5005 V3197 507 $2,350 G5-7VHSB 6.2
5KE256BC204 S251 332 $1,176 G4-7TEZ 1.9 5KE286DTT6001 V3199 507 $2,074 G5-7VHSB 6.2
5KE256BC205 S252 332 $1,141 G4-7TEZ 1.9 5KE286DTT6005 V3198 507 $2,074 G5-7VHSB 6.2
5KE256BC206 S253 332 $1,141 G4-7TEZ 1.9 5KE286FC205 S277 475 $1,960 G4-7TECZ 1.13
5KE256BC304 S254 295 $1,174 G4-7TEZ 1.9 5KE286KC115 S2262 455 $1,863 G4-7TECZ 1.13
5KE256BC305 S255 295 $1,174 G4-7TEZ 1.9 5KE286KC117 S2955 455 $2,257 G4-7TEZ 6.16
5KE256BTE105 S4250 325 $1,136 G4-7TEZ 1.9 5KE286KC205 S2265 475 $1,827 G4-7TECZ 1.13
5KE256BTE205 S4252 290 $1,141 G4-7TEZ 1.9 5KE286KTE115 S5262 465 $1,863 G4-7TECZ 1.13
5KE256CC105 S2630 367 $1,735 G5-7XPZ 1.18 5KE286KTE205 S5265 455 $1,827 G4-7TECZ 1.13
5KE256CC205 S2631 386 $1,719 G5-7XPZ 1.18 5KE324AC114 S3510 535 $2,103 G4-7DEZ 1.4
5KE256CC305 S2623 359 $1,760 G5-7XPZ 1.18 5KE324AC115 S3511 535 $2,104 G4-7DEZ 1.4
5KE256DTT5001 V3170 370 $1,734 G5-7VHSB 6.2 5KE324AC204 S3505 542 $1,686 G4-7DEZ 1.3
5KE256DTT5005 V3171 370 $1,734 G5-7VHSB 6.2 5KE324AC205 S3506 542 $1,687 G4-7DEZ 1.3
5KE256DTT6001 V3173 370 $1,633 G5-7VHSB 6.2 5KE324AC206 S3507 542 $1,686 G4-7DEZ 1.3
5KE256DTT6005 V3174 370 $1,633 G5-7VHSB 6.2 5KE324AC215 S3567 542 $1,687 G4-7DEZ 1.3
5KE256DTT7001 V3177 370 $1,770 G5-7VHSB 6.2 5KE324AC304 S3501 529 $1,700 G4-7DEZ 1.3
5KE256DTT7005 V3178 370 $1,645 G5-7VHSB 6.2 5KE324AC305 S3502 544 $1,700 G4-7DEZ 1.3

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.24 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KE324ATE115 S5511 606 $2,104 G4-7DEZ 1.4 5KE364DTT6007 V3429 1102 $3,444 G5-7VHSB 6.2
5KE324ATE205 S5506 580 $1,687 G4-7DEZ 1.3 5KE364DTT6009 V3430 1102 $3,444 G5-7VHSB 6.2
Cross Reference Guide

5KE324ATE215 S5567 606 $1,687 G4-7DEZ 1.3 5KE364DTT7002 V3435 1102 $3,488 G5-7VHSB 6.2
5KE324ATF105 S3624 595 $2,685 G4-7DEF 6.12 5KE364KFC115 S2943 955 $4,608 G4-7TEZ 6.16
5KE324ATF205 S3608 575 $1,925 G4-7DEF 6.12 5KE364KFC205 S2342 959 $4,261 G4-7TECZ 1.13
5KE324BFC105 S282 788 $2,144 G4-7TEZ 1.10 5KE365AC114 S3528 757 $4,950 G4-7DEZ 1.4
5KE324BFC115 S281 788 $2,144 G4-7TEZ 1.10 5KE365AC115 S3529 757 $4,950 G4-7DEZ 1.4
5KE324BFC204 S284 776 $2,053 G4-7TEZ 1.10 5KE365AC204 S3524 796 $3,200 G4-7DEZ 1.4
5KE324BFC205 S283 776 $2,053 G4-7TEZ 1.10 5KE365AC205 S3525 796 $3,200 G4-7DEZ 1.4
5KE324BFC305 S279 626 $2,312 G4-7TEZ 1.10 5KE365AC215 S3571 796 $3,200 G4-7DEZ 1.4
5KE324BFC315 S278 625 $2,312 G4-7TEZ 1.10 5KE365AC304 S3514 803 $3,455 G4-7DEZ 1.4
5KE324CC115 S2644 691 $3,360 G5-7XPZ 1.18 5KE365AC308 S3515 803 $3,455 G4-7DEZ 1.4
5KE324CC205 S2645 717 $3,256 G5-7XPZ 1.18 5KE365ATE115 S5529 812 $4,950 G4-7DEZ 1.4
5KE324CC305 S2638 682 $3,502 G5-7XPZ 1.18 5KE365ATE205 S5525 838 $3,200 G4-7DEZ 1.4
5KE324DTT5002 V3407 790 $2,725 G5-7VHSB 6.2 5KE365ATE215 S5571 812 $3,200 G4-7DEZ 1.4
5KE324DTT5003 V3450 760 $2,725 G5-7VHSB 6.2 5KE365ATF115 S3627 763 $4,260 G4-7DEF 6.12
5KE324DTT6002 V3411 760 $2,180 G5-7VHSB 6.2 5KE365ATF215 S3611 838 $3,345 G4-7DEF 6.12
5KE324DTT6003 V3409 760 $2,180 G5-7VHSB 6.2 5KE365BFC115 S297 992 $4,581 G4-7TEZ 1.10
5KE324DTT6007 V3410 760 $2,180 G5-7VHSB 6.2 5KE365BFC204 S299 1001 $4,584 G4-7TEZ 1.10
5KE324KFC115 S2941 802 $2,632 G4-7TEZ 6.16 5KE365BFC205 S298 1001 $4,584 G4-7TEZ 1.10
5KE324KFC205 S2340 803 $2,329 G4-7TECZ 1.13 5KE365BFC305 S291 933 $4,337 G4-7TEZ 1.10
5KE326AC114 S3516 603 $2,730 G4-7DEZ 1.4 5KE365CC115 S2656 997 $5,612 G5-7XPZ 1.18
5KE326AC115 S3517 603 $2,730 G4-7DEZ 1.4 5KE365CC205 S2657 997 $6,516 G5-7XPZ 1.18
5KE326AC204 S3512 610 $1,965 G4-7DEZ 1.4 5KE365CC305 S2651 928 $5,836 G5-7XPZ 1.18
5KE326AC205 S3513 610 $1,965 G4-7DEZ 1.4 5KE365DTT6000 V3442 1102 $4,050 G5-7VHSB 6.3
5KE326AC215 S3569 610 $1,965 G4-7DEZ 1.4 5KE365DTT6003 V3554 1102 $4,050 G5-7VHSB 6.3
5KE326AC304 S3503 573 $1,950 G4-7DEZ 1.3 5KE365DTT6007 V3440 1102 $4,050 G5-7VHSB 6.3
5KE326AC305 S3504 573 $1,950 G4-7DEZ 1.3 5KE365DTT6009 V3441 1102 $4,050 G5-7VHSB 6.3
5KE326ATE115 S5517 692 $2,730 G4-7DEZ 1.4 5KE365KFC115 S2944 1012 $5,511 G4-7TEZ 6.16
5KE326ATE205 S5513 639 $1,965 G4-7DEZ 1.4 5KE365KFC205 S2343 1019 $5,362 G4-7TECZ 1.13
5KE326ATE215 S5569 692 $1,965 G4-7DEZ 1.4 5KE404AC114 S3534 931 $6,200 G4-7DEZ 1.5
5KE326ATF105 S3625 661 $2,985 G4-7DEF 6.12 5KE404AC118 S3535 931 $6,200 G4-7DEZ 1.5
5KE326ATF205 S3609 575 $2,232 G4-7DEF 6.12 5KE404AC204 S3530 981 $4,200 G4-7DEZ 1.4
5KE326BFC105 S287 788 $2,774 G4-7TEZ 1.10 5KE404AC205 S3531 981 $4,200 G4-7DEZ 1.4
5KE326BFC115 S286 788 $2,774 G4-7TEZ 1.10 5KE404AC215 S3572 981 $4,200 G4-7DEZ 1.4
5KE326BFC204 S290 803 $2,521 G4-7TEZ 1.10 5KE404AC304 S3520 970 $3,895 G4-7DEZ 1.4
5KE326BFC205 S289 803 $2,521 G4-7TEZ 1.10 5KE404AC308 S3521 970 $3,895 G4-7DEZ 1.4
5KE326BFC215 S288 803 $2,521 G4-7TEZ 1.10 5KE404ATE118 S5535 890 $6,200 G4-7DEZ 1.5
5KE326BFC305 S280 763 $2,709 G4-7TEZ 1.10 5KE404ATE205 S5531 870 $4,200 G4-7DEZ 1.4
5KE326CC115 S2648 770 $4,148 G5-7XPZ 1.18 5KE404ATE215 S5572 890 $4,200 G4-7DEZ 1.4
5KE326CC205 S2649 783 $3,836 G5-7XPZ 1.18 5KE404ATF115 S3628 1031 $5,048 G4-7DEF 6.12
5KE326CC305 S2643 744 $3,925 G5-7XPZ 1.18 5KE404ATF215 S3612 1045 $4,275 G4-7DEF 6.12
5KE326DTT5002 V3551 760 $3,179 G5-7VHSB 6.2 5KE404DTT6002 V3451 1590 $5,325 G5-7VHSB 6.3
5KE326DTT6002 V3422 760 $2,857 G5-7VHSB 6.2 5KE404DTT6003 V3453 1590 $5,325 G5-7VHSB 6.3
5KE326DTT6003 V3420 760 $2,857 G5-7VHSB 6.2 5KE404DTT7002 V3553 1590 $4,791 G5-7VHSB 6.2
5KE326DTT6007 V3421 760 $2,557 G5-7VHSB 6.2 5KE405AC114 S3540 1005 $7,600 G4-7DEZ 1.5
5KE326DTT7002 V3423 885 $2,785 G5-7VHSB 6.2 5KE405AC118 S3541 1005 $7,600 G4-7DEZ 1.5
5KE326KFC115 S2942 835 $3,059 G4-7TEZ 6.16 5KE405AC204 S3536 1094 $5,125 G4-7DEZ 1.5
5KE326KFC205 S2341 812 $2,849 G4-7TECZ 1.13 5KE405AC208 S3537 1094 $5,125 G4-7DEZ 1.5
5KE364AC114 S3522 695 $3,800 G4-7DEZ 1.4 5KE405AC218 S3573 1094 $5,125 G4-7DEZ 1.5
5KE364AC115 S3523 695 $3,800 G4-7DEZ 1.4 5KE405AC304 S3526 1105 $4,930 G4-7DEZ 1.4
5KE364AC204 S3518 719 $2,780 G4-7DEZ 1.4 5KE405AC308 S3527 1105 $4,930 G4-7DEZ 1.4
5KE364AC205 S3519 719 $2,780 G4-7DEZ 1.4 5KE405ATE118 S5541 1150 $7,600 G4-7DEZ 1.5
5KE364AC215 S3570 719 $2,780 G4-7DEZ 1.4 5KE405ATE208 S5537 960 $5,125 G4-7DEZ 1.5
5KE364AC304 S3508 726 $3,000 G4-7DEZ 1.3 5KE405ATE218 S5573 1150 $5,125 G4-7DEZ 1.5
5KE364AC308 S3509 726 $3,000 G4-7DEZ 1.3 5KE405ATF115 S3629 1124 $6,350 G4-7DEF 6.12
5KE364ATE115 S5523 686 $3,800 G4-7DEZ 1.4 5KE405ATF215 S3613 1225 $5,101 G4-7DEF 6.12
5KE364ATE205 S5519 700 $2,780 G4-7DEZ 1.4 5KE405DTT6002 V3456 1590 $5,929 G5-7VHSB 6.3
5KE364ATE215 S5570 686 $2,780 G4-7DEZ 1.4 5KE405DTT7002 V3555 1590 $5,733 G5-7VHSB 6.3
5KE364ATF115 S3626 674 $3,297 G4-7DEF 6.12 5KE405KFC115 S2945 1259 $7,128 G4-7TEZ 6.16
5KE364ATF215 S3610 730 $2,771 G4-7DEF 6.12 5KE405SFC114 S4175 1259 $6,296 G4-7SEZ 1.10
5KE364BFC115 S292 935 $3,751 G4-7TEZ 1.10 5KE405SFC115 S4346 1259 $6,296 G4-7SEZ 1.10
5KE364BFC204 S296 932 $3,617 G4-7TEZ 1.10 5KE405SFC118 S4116 1259 $6,296 G4-7SEZ 1.10
5KE364BFC205 S295 932 $3,617 G4-7TEZ 1.10 5KE405SFC204 S4176 1299 $5,810 G4-7SEZ 1.10
5KE364BFC215 S293 928 $3,617 G4-7TEZ 1.10 5KE405SFC205 S4347 1299 $5,810 G4-7SEZ 1.10
5KE364BFC305 S285 932 $3,719 G4-7TEZ 1.10 5KE405SFC208 S4117 1299 $5,810 G4-7SEZ 1.10
5KE364CC115 S2653 816 $5,357 G5-7XPZ 1.18 5KE405SFC215 S4123 1299 $5,810 G4-7SEZ 1.10
5KE364CC205 S2654 911 $5,318 G5-7XPZ 1.18 5KE405SS304 S2174 1450 $6,496 G6-7SE 8.14
5KE364CC305 S2647 871 $5,191 G5-7XPZ 1.18 5KE405SS308 S2333 1450 $6,496 G6-7SE 8.14
5KE364DTT5002 V3428 1102 $3,995 G5-7VHSB 6.2 5KE444AC114 S3546 1150 $11,485 G4-7DEZ 1.5
5KE364DTT6000 V3552 1102 $3,444 G5-7VHSB 6.2 5KE444AC118 S3547 1150 $11,485 G4-7DEZ 1.5
5KE364DTT6003 V3431 1102 $3,444 G5-7VHSB 6.2 5KE444AC204 S3542 1320 $7,485 G4-7DEZ 1.5

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.25
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KE444AC208 S3543 1320 $7,485 G4-7DEZ 1.5 5KGS404SAA320 M8984 1480 $9,999 G4-7UC 3.9
5KE444AC218 S3574 1320 $7,485 G4-7DEZ 1.5 5KGS405SAA221 M8994 1500 $10,946 G4-7UC 3.9

Cross Reference Guide

5KE444AC304 S3532 1166 $6,215 G4-7DEZ 1.4 5KGS405SAA321 M8985 1530 $11,000 G4-7UC 3.9
5KE444AC308 S3533 1166 $6,215 G4-7DEZ 1.4 5KGS444SAA220 M8995 1970 $14,473 G4-7UC 3.9
5KE444ATE118 S5547 1310 $11,485 G4-7DEZ 1.5 5KGS444SAA320 M8986 1920 $14,854 G4-7UC 3.9
5KE444ATE208 S5543 1330 $7,485 G4-7DEZ 1.5 5KGS445SAA220 M8996 2060 $16,604 G4-7UC 3.9
5KE444ATE218 S5574 1310 $7,485 G4-7DEZ 1.5 5KGS447SAA220 M8997 2700 $20,755 G4-7UC 3.9
5KE444ATF118 S3630 1510 $9,350 G4-7DEF 6.12 5KGS447SAA320 M8988 2700 $21,313 G4-7UC 3.9
5KE444ATF218 S3614 1430 $6,705 G4-7DEF 6.12 5KGS449SAA222 M8998 2980 $23,135 G4-7UC 3.9
5KE444DTT6002 V3466 2075 $7,360 G5-7VHSB 6.3 5KGS449SAA224 M8999 3100 $26,938 G4-7UC 3.9
5KE444DTT6003 V3464 2075 $7,360 G5-7VHSB 6.3 5KGS449SAA321 M8989 3070 $23,639 G4-7UC 3.9
5KE444DTT7002 V3556 2075 $7,806 G5-7VHSB 6.3 5KPM81HFL0095 5315 2 $34 G3-1CON 8.3
5KE444DTT7009 V3468 2075 $7,806 G5-7VHSB 6.3 5KPM81HFL0096 5325 2 $36 G3-1CON 8.3
5KE444KFC118 S2946 1623 $9,327 G4-7TEZ 6.16 5KPM81HFL0097 5335 2 $34 G3-1CON 8.3
5KE444SFC114 S4178 1623 $8,230 G4-7SEZ 1.11 5KPM81HFL0098 5345 2 $36 G3-1CON 8.3
5KE444SFC118 S4334 1623 $8,230 G4-7SEZ 1.11 5KPM81HFL1086 5415 3 $40 G3-1CON 8.3
5KE444SFC204 S4179 1554 $7,648 G4-7SEZ 1.11 5KPM81HFL1087 5425 3 $42 G3-1CON 8.3
5KE444SFC208 S4119 1554 $7,648 G4-7SEZ 1.11 5KPM81HFL1088 5435 3 $40 G3-1CON 8.3
5KE444SFC218 S4348 1554 $7,648 G4-7SEZ 1.11 5KPM81HFL1089 5445 3 $42 G3-1CON 8.3
5KE444SFC304 S4177 1671 $8,400 G4-7SEZ 1.10 5KPM81HFL3046S 5815 4 $45 G3-1CON 8.3
5KE444SFC308 S4118 1671 $8,400 G4-7SEZ 1.10 5KPM81HFL3047S 5825 4 $47 G3-1CON 8.3
5KE445AC114 S3552 1276 $14,244 G4-7DEZ 1.5 5KPM81HFL3048S 5835 4 $45 G3-1CON 8.3
5KE445AC118 S3553 1276 $14,225 G4-7DEZ 1.5 5KPM81HFL3049S 5845 4 $47 G3-1CON 8.3
5KE445AC120 S3558 1320 $17,363 G4-7DEZ 1.5 5KS 184CSP105 E9611 101 $886 G6-7XP$ 8.10
5KE445AC121 S3559 1320 $17,363 G4-7DEZ 1.5 5KS143ATE105 E709 46 $242 G4-7D$Z1 2.2
5KE445AC204 S3548 1430 $10,094 G4-7DEZ 1.5 5KS143ATE205 E707 46 $222 G4-7D$Z1 2.2
5KE445AC208 S3549 1430 $10,095 G4-7DEZ 1.5 5KS143SAA104 M487 43 $499 G4-7U1 3.2
5KE445AC218 S3575 1430 $10,095 G4-7DEZ 1.5 5KS143SAA105 M486 43 $499 G4-7U1 3.2
5KE445AC304 S3538 1276 $7,815 G4-7DEZ 1.5 5KS143SAA125 M462 43 $618 G4-7U1 3.2
5KE445AC308 S3539 1276 $7,815 G4-7DEZ 1.5 5KS143SAA126 M463 43 $618 G4-7U1 3.2
5KE445AC320 S3544 1364 $9,145 G4-7DEZ 1.5 5KS143SAA127 M465 43 $692 G4-7U1 3.2
5KE445AC321 S3545 1364 $9,145 G4-7DEZ 1.5 5KS143SAA204 M483 43 $430 G4-7U1 3.2
5KE445ATE118 S5553 1480 $14,225 G4-7DEZ 1.5 5KS143SAA205 M482 43 $430 G4-7U1 3.2
5KE445ATE121 S5559 1480 $17,363 G4-7DEZ 1.5 5KS143SAA208 M475 43 $559 G4-7U1 3.2
5KE445ATE208 S5549 1510 $10,095 G4-7DEZ 1.5 5KS143SAA209 M497 43 $483 G4-7U1 3.8
5KE445ATE218 S5575 1480 $10,095 G4-7DEZ 1.5 5KS143SAA266 M478 43 $523 G4-7U1 3.8
5KE445ATF218 S3615 1610 $8,789 G4-7DEF 6.12 5KS143SAA300 M496 43 $555 G4-7U1 3.8
5KE445DTT6002 V3483 2260 $9,962 G5-7VHSB 6.3 5KS143SAA304 M481 43 $502 G4-7U1 3.2
5KE445DTT6003 V3470 2260 $9,962 G5-7VHSB 6.3 5KS143SAA305 M480 43 $502 G4-7U1 3.2
5KE445KFC118 S2947 1722 $12,063 G4-7TEZ 6.16 5KS143STE105 M7700 52 $328 G4-7S$P 2.6
5KE445SFC114 S4181 1722 $9,886 G4-7SEZ 1.11 5KS143STE109 M7701 52 $365 G4-7S$P 2.6
5KE445SFC118 S4121 1722 $9,886 G4-7SEZ 1.11 5KS143STE205 M7723 52 $332 G4-7S$P 2.6
5KE445SFC204 S4182 1739 $8,891 G4-7SEZ 1.11 5KS143STE222 M7738 50 $360 G4-7S$P1 2.8
5KE445SFC208 S4122 1739 $8,891 G4-7SEZ 1.11 5KS143XAA121 M8903 43 $690 G4-7UX1 3.18
5KE445SFC218 S4349 1739 $8,891 G4-7SEZ 1.11 5KS143XAA122 M8905 43 $720 G4-7UX1 3.18
5KE445SFC304 S4180 1775 $9,780 G4-7SEZ 1.11 5KS143XAA123 M8904 43 $690 G4-7UX1 3.18
5KE445SFC308 S4120 1775 $9,780 G4-7SEZ 1.11 5KS143XAA124 M8906 43 $720 G4-7UX1 3.18
5KE447AC120 S3562 1590 $19,850 G4-7DEZ 1.5 5KS143XAA125 M8907 43 $862 G4-7UX1 3.18
5KE447AC121 S3563 1590 $19,850 G4-7DEZ 1.5 5KS143XAA126 M8908 43 $862 G4-7UX1 3.18
5KE447AC204 S3554 1760 $12,150 G4-7DEZ 1.5 5KS143XAA204 M353 43 $680 G4-7UX1 3.18
5KE447AC208 S3555 1760 $12,150 G4-7DEZ 1.5 5KS143XAA208 M352 43 $680 G4-7UX1 3.18
5KE447AC320 S3550 1810 $14,550 G4-7DEZ 1.5 5KS143XAA266 M520 43 $763 G4-7UX1 3.22
5KE447AC321 S3551 1810 $14,550 G4-7DEZ 1.5 5KS143XAA304 M355 43 $672 G4-7UX1 3.18
5KE447ATE121 S5563 2100 $19,850 G4-7DEZ 1.5 5KS143XAA308 M354 43 $672 G4-7UX1 3.18
5KE447SAA114 S4384 2560 $12,506 G4-7SEZ 1.11 5KS145ATE102 E717 58 $285 G4-7D$Z1 2.2
5KE447SAA120 S4387 2730 $12,506 G4-7SEZ 1.11 5KS145ATE105 E719 60 $320 G4-7D$Z1 2.2
5KE447SAA204 S4385 2560 $10,814 G4-7SEZ 1.11 5KS145ATE202 E710 56 $242 G4-7D$Z1 2.2
5KE447SAA208 S4352 2560 $10,814 G4-7SEZ 1.11 5KS145ATE205 E718 58 $267 G4-7D$Z1 2.2
5KE449AC120 S3564 1760 $20,280 G4-7DEZ 1.5 5KS145ATE305 E708 58 $285 G4-7D$Z1 2.2
5KE449AC121 S3565 1760 $20,580 G4-7DEZ 1.5 5KS145SAA104 M491 50 $532 G4-7U1 3.2
5KE449AC204 S3560 1870 $15,985 G4-7DEZ 1.5 5KS145SAA105 M490 50 $532 G4-7U1 3.2
5KE449AC208 S3561 1870 $15,985 G4-7DEZ 1.5 5KS145SAA204 M489 50 $526 G4-7U1 3.2
5KE449AC320 S3556 2160 $16,500 G4-7DEZ 1.5 5KS145SAA205 M488 50 $526 G4-7U1 3.2
5KE449AC321 S3557 2160 $16,500 G4-7DEZ 1.5 5KS145SAA208 M494 50 $526 G4-7U1 3.2
5KE449SAA208 S4353 2580 $13,567 G4-7SEZ 1.11 5KS145SAA209 M492 50 $478 G4-7U1 3.2
5KE449SAA304 S4386 2730 $14,800 G4-7SEZ 1.11 5KS145SAA210 M493 50 $478 G4-7U1 3.2
5KE449SAA308 S4351 2730 $14,800 G4-7SEZ 1.11 5KS145SAA220 M500 50 $579 G4-7U1 3.8
5KGS364SAA220 M8992 1030 $7,420 G4-7UC 3.9 5KS145SAA230 M479 50 $531 G4-7U1 3.8
5KGS364SAA320 M8982 1000 $7,439 G4-7UC 3.9 5KS145SAA231 M499 50 $531 G4-7U1 3.8
5KGS365SAA220 M8993 1090 $8,826 G4-7UC 3.9 5KS145SAA233 M464 50 $621 G4-7U1 3.2
5KGS365SAA320 M8983 1030 $8,507 G4-7UC 3.9 5KS145SAA303 M498 50 $586 G4-7U1 3.8

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.26 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS145SAA304 M485 50 $533 G4-7U1 3.2 5KS184SAA100 M9947 101 $792 G4-7U1 3.8
5KS145SAA305 M484 50 $533 G4-7U1 3.2 5KS184SAA104 M9722 101 $712 G4-7U1 3.3
Cross Reference Guide

5KS145SAA308 M476 50 $693 G4-7U1 3.2 5KS184SAA105 M240 101 $712 G4-7U1 3.3
5KS145SAA404 M477 50 $901 G4-7U1 3.2 5KS184SAA108 M9940 101 $712 G4-7U1 3.3
5KS145SAA422 M460 50 $901 G4-7U1 3.2 5KS184SAA202 M9890 101 $764 G4-7U1 3.8
5KS145STE105 M7702 52 $426 G4-7S$P 2.6 5KS184SAA204 M9718 101 $684 G4-7U1 3.3
5KS145STE205 M7725 58 $406 G4-7S$P 2.6 5KS184SAA205 M242 101 $684 G4-7U1 3.3
5KS145STE209 M7724 58 $369 G4-7S$P 2.6 5KS184SAA208 M9942 101 $684 G4-7U1 3.3
5KS145STE222 M7739 61 $390 G4-7S$P1 2.8 5KS184SAA300 M9948 101 $755 G4-7U1 3.8
5KS145STE229 M7740 64 $440 G4-7S$P1 2.8 5KS184SAA304 M9706 101 $675 G4-7U1 3.2
5KS145XAA204 M360 50 $771 G4-7UX1 3.18 5KS184SAA305 M9704 101 $675 G4-7U1 3.2
5KS145XAA208 M359 50 $771 G4-7UX1 3.18 5KS184SAA308 M9944 101 $675 G4-7U1 3.2
5KS145XAA210 M362 50 $833 G4-7UX1 3.18 5KS184SAA404 M9874 101 $967 G4-7U1 3.2
5KS145XAA211 M361 50 $833 G4-7UX1 3.18 5KS184SAA405 M9873 101 $967 G4-7U1 3.2
5KS145XAA223 M526 50 $981 G4-7UX1 3.22 5KS184SAA408 M9888 101 $967 G4-7U1 3.2
5KS145XAA230 M521 50 $857 G4-7UX1 3.22 5KS184SAE5705 V825 101 $1,304 G6-7VIL 6.8
5KS145XAA304 M364 50 $728 G4-7UX1 3.18 5KS184SAE6705 V834 101 $1,118 G6-7VIL 6.8
5KS145XAA308 M363 50 $728 G4-7UX1 3.18 5KS184STE105 M7704 106 $593 G4-7S$P 2.6
5KS145XAA420 M8901 50 $1,108 G4-7UX1 3.18 5KS184STE122 M7716 112 $620 G4-7S$P1 2.8
5KS182ATE105 E721 72 $389 G4-7D$Z1 2.2 5KS184STE205 M7727 106 $425 G4-7S$P 2.6
5KS182ATE204 E7635 72 $277 G4-7D$Z1 2.2 5KS184STE222 M7742 117 $575 G4-7S$P1 2.8
5KS182ATE205 E720 72 $277 G4-7D$Z1 2.2 5KS184XAA100 M8927 101 $989 G4-7UX1 3.22
5KS182ATE206 E7714 72 $277 G4-7D$Z1 2.2 5KS184XAA104 M9492 101 $889 G4-7UX1 3.19
5KS182ATE305 E7707 72 $313 G4-7D$Z1 2.2 5KS184XAA108 M9422 101 $889 G4-7UX1 3.19
5KS182CSP104 E9606 76 $762 G6-7XP$ 8.10 5KS184XAA202 M8910 101 $880 G4-7UX1 3.22
5KS182CSP105 E9605 76 $762 G6-7XP$ 8.10 5KS184XAA204 M9493 101 $788 G4-7UX1 3.19
5KS182CSP204 E9608 76 $730 G6-7XP$ 8.10 5KS184XAA208 M9423 101 $788 G4-7UX1 3.19
5KS182CSP205 E9607 76 $730 G6-7XP$ 8.10 5KS184XAA261 M6621 101 $1,315 G4-7UXHE 3.30
5KS182CSP304 E9602 76 $747 G6-7XP$ 8.10 5KS184XAA300 M8928 101 $871 G4-7UX1 3.22
5KS182CSP305 E9601 76 $747 G6-7XP$ 8.10 5KS184XAA304 M9486 101 $779 G4-7UX1 3.18
5KS182SAA100 M9945 76 $680 G4-7U1 3.8 5KS184XAA308 M9416 101 $779 G4-7UX1 3.18
5KS182SAA104 M9715 76 $600 G4-7U1 3.3 5KS184XAA404 M9485 101 $1,051 G4-7UX1 3.18
5KS182SAA105 M9713 76 $600 G4-7U1 3.3 5KS184XAA408 M9415 101 $1,051 G4-7UX1 3.18
5KS182SAA108 M9939 76 $600 G4-7U1 3.3 5KS213ATE105 E750 163 $665 G4-7D$Z1 2.2
5KS182SAA204 M9711 76 $583 G4-7U1 3.3 5KS213ATE204 E7640 157 $538 G4-7D$Z1 2.2
5KS182SAA205 M241 76 $583 G4-7U1 3.3 5KS213ATE205 E730 128 $538 G4-7D$Z1 2.2
5KS182SAA207 M9889 76 $663 G4-7U1 3.8 5KS213ATE206 E7729 128 $538 G4-7D$Z1 2.2
5KS182SAA208 M9941 76 $583 G4-7U1 3.3 5KS213ATE305 E7011 128 $514 G4-7D$Z1 2.2
5KS182SAA300 M9946 76 $684 G4-7U1 3.8 5KS213CSP104 E9617 200 $1,041 G6-7XP$ 8.10
5KS182SAA304 M9703 76 $604 G4-7U1 3.2 5KS213CSP105 E9661 200 $1,041 G6-7XP$ 8.10
5KS182SAA305 M9702 76 $604 G4-7U1 3.2 5KS213CSP204 E9618 200 $1,036 G6-7XP$ 8.10
5KS182SAA308 M9943 76 $604 G4-7U1 3.2 5KS213CSP205 E9669 200 $1,036 G6-7XP$ 8.10
5KS182SAA404 M9872 76 $819 G4-7U1 3.2 5KS213CSP304 E9610 200 $951 G6-7XP$ 8.10
5KS182SAA405 M9871 76 $819 G4-7U1 3.2 5KS213CSP305 E9678 200 $951 G6-7XP$ 8.10
5KS182SAA408 M9887 76 $819 G4-7U1 3.2 5KS213SAA101 M9949 200 $1,010 G4-7U1 3.8
5KS182SAE5705 V824 76 $1,029 G6-7VIL 6.8 5KS213SAA104 M9728 200 $930 G4-7U1 3.3
5KS182SAE6705 V833 76 $1,029 G6-7VIL 6.8 5KS213SAA105 M9144 200 $930 G4-7U1 3.3
5KS182STE105 M7703 96 $479 G4-7S$P 2.6 5KS213SAA108 M990 200 $930 G4-7U1 3.3
5KS182STE122 M7715 88 $505 G4-7S$P1 2.8 5KS213SAA200 M9891 200 $1,004 G4-7U1 3.8
5KS182STE205 M7726 96 $450 G4-7S$P 2.6 5KS213SAA204 M9730 200 $924 G4-7U1 3.3
5KS182STE222 M7741 92 $485 G4-7S$P1 2.8 5KS213SAA205 M9145 200 $924 G4-7U1 3.3
5KS182XAA100 M8925 76 $814 G4-7UX1 3.22 5KS213SAA208 M9911 200 $924 G4-7U1 3.3
5KS182XAA104 M9488 76 $718 G4-7UX1 3.18 5KS213SAA300 M9950 200 $900 G4-7U1 3.8
5KS182XAA108 M9418 76 $718 G4-7UX1 3.18 5KS213SAA304 M9712 200 $820 G4-7U1 3.3
5KS182XAA204 M9489 76 $674 G4-7UX1 3.18 5KS213SAA305 M9142 200 $820 G4-7U1 3.3
5KS182XAA207 M8909 76 $766 G4-7UX1 3.22 5KS213SAA308 M9111 200 $820 G4-7U1 3.3
5KS182XAA208 M9419 76 $674 G4-7UX1 3.18 5KS213SAA404 M9876 200 $1,155 G4-7U1 3.2
5KS182XAA300 M8926 76 $789 G4-7UX1 3.22 5KS213SAA405 M9875 200 $1,155 G4-7U1 3.2
5KS182XAA304 M9483 76 $697 G4-7UX1 3.18 5KS213SAA408 M9705 200 $1,155 G4-7U1 3.2
5KS182XAA308 M9414 76 $697 G4-7UX1 3.18 5KS213SAE5705 V826 200 $1,453 G6-7VIL 6.8
5KS182XAA404 M9482 76 $889 G4-7UX1 3.18 5KS213SAE6705 V835 200 $1,426 G6-7VIL 6.8
5KS182XAA408 M9413 76 $889 G4-7UX1 3.18 5KS213STE105 M7705 168 $717 G4-7S$P 2.6
5KS184ATE105 E723 91 $560 G4-7D$Z1 2.2 5KS213STE122 M7717 151 $810 G4-7S$P1 2.8
5KS184ATE204 E7808 91 $389 G4-7D$Z1 2.2 5KS213STE205 M7728 168 $713 G4-7S$P 2.6
5KS184ATE205 E722 91 $389 G4-7D$Z1 2.2 5KS213STE222 M7743 155 $810 G4-7S$P1 2.8
5KS184ATE206 E7716 91 $389 G4-7D$Z1 2.2 5KS213XAA101 M8929 200 $1,166 G4-7UX1 3.22
5KS184ATE305 E7710 91 $402 G4-7D$Z1 2.2 5KS213XAA104 M9496 200 $1,074 G4-7UX1 3.19
5KS184CSP104 E9612 101 $886 G6-7XP$ 8.10 5KS213XAA108 M9426 200 $1,074 G4-7UX1 3.19
5KS184CSP204 E9614 101 $813 G6-7XP$ 8.10 5KS213XAA200 M8911 200 $1,159 G4-7UX1 3.22
5KS184CSP205 E9613 101 $813 G6-7XP$ 8.10 5KS213XAA204 M9497 200 $1,067 G4-7UX1 3.19
5KS184CSP304 E9604 101 $806 G6-7XP$ 8.10 5KS213XAA208 M9427 200 $1,067 G4-7UX1 3.19
5KS184CSP305 E9603 101 $806 G6-7XP$ 8.10 5KS213XAA278 M6622 200 $1,710 G4-7UXHE 3.30

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.27
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS213XAA304 M9490 200 $950 G4-7UX1 3.18 5KS254SAA405 M9879 315 $1,917 G4-7U1 3.3
5KS213XAA308 M9420 200 $950 G4-7UX1 3.18 5KS254SAA408 M9719 315 $1,917 G4-7U1 3.3

Cross Reference Guide

5KS213XAA404 M9487 200 $1,354 G4-7UX1 3.18 5KS254SAE5705 V828 315 $1,814 G6-7VIL 6.8
5KS213XAA408 M9417 200 $1,354 G4-7UX1 3.18 5KS254SAE6705 V837 315 $1,908 G6-7VIL 6.8
5KS215ATE105 E751 157 $842 G4-7D$Z1 2.2 5KS254STE105 M7707 290 $1,151 G4-7S$P 2.6
5KS215ATE204 E7643 157 $650 G4-7D$Z1 2.2 5KS254STE122 M7719 287 $1,250 G4-7S$P1 2.8
5KS215ATE205 E731 157 $650 G4-7D$Z1 2.2 5KS254STE205 M7730 290 $1,131 G4-7S$P 2.6
5KS215ATE206 E7734 157 $650 G4-7D$Z1 2.2 5KS254STE222 M7745 285 $1,260 G4-7S$P1 2.8
5KS215ATE305 E7012 157 $643 G4-7D$Z1 2.2 5KS254XAA100 M8933 315 $1,845 G4-7UX1 3.22
5KS215CSP104 E9620 220 $1,173 G6-7XP$ 8.10 5KS254XAA104 M9567 315 $1,725 G4-7UX1 3.19
5KS215CSP105 E9662 220 $1,173 G6-7XP$ 8.10 5KS254XAA108 M9434 315 $1,725 G4-7UX1 3.19
5KS215CSP204 E9621 220 $1,195 G6-7XP$ 8.10 5KS254XAA200 M8913 315 $1,818 G4-7UX1 3.22
5KS215CSP205 E9671 220 $1,195 G6-7XP$ 8.10 5KS254XAA204 M9568 315 $1,694 G4-7UX1 3.19
5KS215CSP304 E9616 220 $1,233 G6-7XP$ 8.10 5KS254XAA208 M9435 315 $1,694 G4-7UX1 3.19
5KS215CSP305 E9679 220 $1,233 G6-7XP$ 8.10 5KS254XAA267 M6624 315 $2,122 G4-7UXHE 3.30
5KS215SAA100 M9951 220 $1,170 G4-7U1 3.8 5KS254XAA300 M8934 315 $1,898 G4-7UX1 3.22
5KS215SAA104 M9733 220 $1,090 G4-7U1 3.4 5KS254XAA304 M9498 315 $1,778 G4-7UX1 3.19
5KS215SAA105 M9147 220 $1,090 G4-7U1 3.4 5KS254XAA308 M9428 315 $1,778 G4-7UX1 3.19
5KS215SAA108 M991 220 $1,090 G4-7U1 3.4 5KS254XAA404 M9495 315 $2,410 G4-7UX1 3.19
5KS215SAA203 M9892 220 $1,111 G4-7U1 3.8 5KS254XAA408 M9425 315 $2,410 G4-7UX1 3.19
5KS215SAA204 M9738 220 $1,031 G4-7U1 3.4 5KS256ATE105 E753 310 $1,212 G4-7D$Z1 2.2
5KS215SAA205 M9148 220 $1,031 G4-7U1 3.4 5KS256ATE204 E7649 310 $1,055 G4-7D$Z1 2.2
5KS215SAA208 M9912 220 $1,031 G4-7U1 3.4 5KS256ATE205 E733 310 $1,055 G4-7D$Z1 2.2
5KS215SAA300 M9952 220 $1,245 G4-7U1 3.8 5KS256ATE206 E7754 310 $1,055 G4-7D$Z1 2.2
5KS215SAA304 M9717 220 $1,165 G4-7U1 3.3 5KS256ATE305 E7014 310 $981 G4-7D$Z1 2.2
5KS215SAA305 M9143 220 $1,165 G4-7U1 3.3 5KS256CSP104 E9626 350 $1,928 G6-7XP$ 8.11
5KS215SAA308 M9112 220 $1,165 G4-7U1 3.3 5KS256CSP105 E9664 350 $1,928 G6-7XP$ 8.11
5KS215SAA404 M9878 220 $1,443 G4-7U1 3.3 5KS256CSP204 E9627 350 $1,910 G6-7XP$ 8.11
5KS215SAA405 M9877 220 $1,443 G4-7U1 3.3 5KS256CSP205 E9673 350 $1,910 G6-7XP$ 8.11
5KS215SAA408 M9708 220 $1,443 G4-7U1 3.3 5KS256CSP304 E9622 350 $1,955 G6-7XP$ 8.10
5KS215SAE5705 V827 220 $1,604 G6-7VIL 6.8 5KS256CSP305 E9686 350 $1,955 G6-7XP$ 8.10
5KS215SAE6705 V836 220 $1,569 G6-7VIL 6.8 5KS256SAA100 M9955 350 $1,905 G4-7U1 3.8
5KS215STE105 M7706 192 $838 G4-7S$P 2.6 5KS256SAA104 M9749 350 $1,801 G4-7U1 3.4
5KS215STE122 M7718 190 $966 G4-7S$P1 2.8 5KS256SAA105 M9153 350 $1,801 G4-7U1 3.4
5KS215STE205 M7729 192 $859 G4-7S$P 2.6 5KS256SAA108 M993 350 $1,801 G4-7U1 3.4
5KS215STE222 M7744 203 $966 G4-7S$P1 2.8 5KS256SAA200 M9894 350 $1,798 G4-7U1 3.8
5KS215XAA100 M8931 220 $1,347 G4-7UX1 3.22 5KS256SAA204 M9751 350 $1,694 G4-7U1 3.4
5KS215XAA104 M9563 220 $1,255 G4-7UX1 3.19 5KS256SAA205 M9154 350 $1,694 G4-7U1 3.4
5KS215XAA108 M9430 220 $1,255 G4-7UX1 3.19 5KS256SAA208 M9914 350 $1,694 G4-7U1 3.4
5KS215XAA203 M8912 220 $1,386 G4-7UX1 3.22 5KS256SAA300 M9956 350 $2,002 G4-7U1 3.8
5KS215XAA204 M9564 220 $1,286 G4-7UX1 3.19 5KS256SAA304 M9737 350 $1,898 G4-7U1 3.4
5KS215XAA208 M9431 220 $1,286 G4-7UX1 3.19 5KS256SAA305 M9149 350 $1,898 G4-7U1 3.4
5KS215XAA259 M6623 220 $1,789 G4-7UXHE 3.30 5KS256SAA308 M9114 350 $1,898 G4-7U1 3.4
5KS215XAA300 M8932 220 $1,430 G4-7UX1 3.22 5KS256SAA404 M9882 350 $2,423 G4-7U1 3.3
5KS215XAA304 M9494 220 $1,338 G4-7UX1 3.19 5KS256SAA405 M9881 350 $2,423 G4-7U1 3.3
5KS215XAA308 M9424 220 $1,338 G4-7UX1 3.19 5KS256SAA408 M9724 350 $2,423 G4-7U1 3.3
5KS215XAA404 M9491 220 $1,747 G4-7UX1 3.18 5KS256SAC5705 V829 350 $2,039 G6-7VIL 6.8
5KS215XAA408 M9421 220 $1,747 G4-7UX1 3.18 5KS256SAE6705 V838 350 $2,123 G6-7VIL 6.8
5KS254ATE105 E752 260 $993 G4-7D$Z1 2.2 5KS256STE105 M7708 325 $1,426 G4-7S$P 2.6
5KS254ATE204 E7646 260 $864 G4-7D$Z1 2.2 5KS256STE122 M7720 344 $1,640 G4-7S$P1 2.8
5KS254ATE205 E732 260 $864 G4-7D$Z1 2.2 5KS256STE205 M7731 325 $1,409 G4-7S$P 2.6
5KS254ATE206 E7744 260 $864 G4-7D$Z1 2.2 5KS256STE222 M7746 329 $1,640 G4-7S$P1 2.8
5KS254ATE305 E7013 260 $838 G4-7D$Z1 2.2 5KS256XAA100 M8935 350 $2,258 G4-7UX1 3.22
5KS254CSP104 E9623 315 $1,629 G6-7XP$ 8.10 5KS256XAA104 M9571 350 $2,135 G4-7UX1 3.19
5KS254CSP105 E9663 315 $1,629 G6-7XP$ 8.10 5KS256XAA108 M9438 350 $2,135 G4-7UX1 3.19
5KS254CSP204 E9624 315 $1,607 G6-7XP$ 8.10 5KS256XAA200 M8914 350 $2,241 G4-7UX1 3.22
5KS254CSP205 E9672 315 $1,607 G6-7XP$ 8.10 5KS256XAA204 M9572 350 $2,111 G4-7UX1 3.19
5KS254CSP305 E9680 315 $1,668 G6-7XP$ 8.10 5KS256XAA208 M9439 350 $2,111 G4-7UX1 3.19
5KS254QRA6EA8 E9619 315 $1,668 G6-7XP$ 8.10 5KS256XAA254 M6625 350 $2,439 G4-7UXHE 3.30
5KS254SAA100 M9953 315 $1,905 G4-7U1 3.8 5KS256XAA300 M8936 350 $2,292 G4-7UX1 3.22
5KS254SAA104 M9741 315 $1,496 G4-7U1 3.4 5KS256XAA304 M9565 350 $2,173 G4-7UX1 3.19
5KS254SAA105 M9150 315 $1,496 G4-7U1 3.4 5KS256XAA308 M9432 350 $2,173 G4-7UX1 3.19
5KS254SAA108 M992 315 $1,496 G4-7U1 3.4 5KS256XAA404 M9499 350 $3,051 G4-7UX1 3.19
5KS254SAA200 M9893 315 $1,522 G4-7U1 3.8 5KS256XAA408 M9429 350 $3,051 G4-7UX1 3.19
5KS254SAA204 M9745 315 $1,418 G4-7U1 3.4 5KS284ATE115 E754 420 $1,446 G4-7D$Z1 2.3
5KS254SAA205 M9151 315 $1,418 G4-7U1 3.4 5KS284ATE204 E7652 394 $1,226 G4-7D$Z1 2.2
5KS254SAA208 M9913 315 $1,418 G4-7U1 3.4 5KS284ATE205 E734 394 $1,226 G4-7D$Z1 2.2
5KS254SAA300 M9954 315 $1,651 G4-7U1 3.8 5KS284ATE206 E7757 394 $1,226 G4-7D$Z1 2.2
5KS254SAA304 M9726 315 $1,547 G4-7U1 3.3 5KS284ATE305 E7015 394 $1,263 G4-7D$Z1 2.2
5KS254SAA305 M9146 315 $1,547 G4-7U1 3.3 5KS284CSP114 E9629 460 $2,424 G6-7XP$ 8.11
5KS254SAA308 M9113 315 $1,547 G4-7U1 3.3 5KS284CSP204 E9630 460 $2,338 G6-7XP$ 8.11
5KS254SAA404 M9880 315 $1,917 G4-7U1 3.3 5KS284CSP205 E9674 460 $2,338 G6-7XP$ 8.11

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.28 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS284CSP304 E9625 460 $2,606 G6-7XP$ 8.10 5KS286XAA200 M8916 510 $3,091 G4-7UX1 3.22
5KS284CSP305 E9682 460 $2,606 G6-7XP$ 8.10 5KS286XAA204 M9580 510 $2,922 G4-7UX1 3.20
Cross Reference Guide

5KS284SAA100 M9903 460 $2,403 G4-7U1 3.8 5KS286XAA208 M9447 510 $2,922 G4-7UX1 3.20
5KS284SAA114 M9838 460 $2,256 G4-7U1 3.4 5KS286XAA255 M6627 510 $3,250 G4-7UXHE 3.30
5KS284SAA115 M9156 460 $2,256 G4-7U1 3.4 5KS286XAA300 M8922 510 $3,679 G4-7UX1 3.22
5KS284SAA118 M994 460 $2,256 G4-7U1 3.4 5KS286XAA304 M9573 510 $3,512 G4-7UX1 3.19
5KS284SAA200 M9895 460 $2,309 G4-7U1 3.8 5KS286XAA308 M9440 510 $3,512 G4-7UX1 3.19
5KS284SAA204 M9759 460 $2,162 G4-7U1 3.4 5KS286XAA404 M9570 510 $4,726 G4-7UX1 3.19
5KS284SAA205 M9157 460 $2,162 G4-7U1 3.4 5KS286XAA408 M9437 510 $4,726 G4-7UX1 3.19
5KS284SAA208 M9935 460 $2,162 G4-7U1 3.4 5KS324ATE115 E756 606 $2,199 G4-7D$Z1 2.3
5KS284SAA300 M9901 460 $2,672 G4-7U1 3.8 5KS324ATE204 E7310 580 $1,772 G4-7D$Z1 2.3
5KS284SAA304 M9746 460 $2,525 G4-7U1 3.4 5KS324ATE205 E736 480 $1,772 G4-7D$Z1 2.3
5KS284SAA305 M9152 460 $2,525 G4-7U1 3.4 5KS324ATE305 E7019 580 $1,838 G4-7D$Z1 2.2
5KS284SAA308 M9115 460 $2,525 G4-7U1 3.4 5KS324CS205 E9676 730 $3,618 G6-7XP$ 8.11
5KS284SAA404 M9884 460 $2,828 G4-7U1 3.4 5KS324SAA108 M9820 670 $3,301 G4-7U1 3.5
5KS284SAA405 M9883 460 $2,828 G4-7U1 3.4 5KS324SAA114 M9829 670 $3,301 G4-7U1 3.5
5KS284SAA408 M9736 460 $2,828 G4-7U1 3.4 5KS324SAA115 M9162 670 $3,301 G4-7U1 3.5
5KS284SAE5705 V830 460 $2,281 G6-7VIL 6.8 5KS324SAA118 M996 670 $3,301 G4-7U1 3.5
5KS284SAE6705 V839 460 $2,418 G6-7VIL 6.8 5KS324SAA152 M8964 670 $3,514 G4-7U1 3.8
5KS284STE105 M7749 445 $1,637 G4-7S$P 2.6 5KS324SAA2007 M8965 710 $3,485 G4-7U1 3.8
5KS284STE112 M7721 477 $1,950 G4-7S$P1 2.8 5KS324SAA204 M9768 710 $3,272 G4-7U1 3.5
5KS284STE115 M7709 445 $1,637 G4-7S$P 2.6 5KS324SAA205 M9163 710 $3,272 G4-7U1 3.5
5KS284STE205 M7732 430 $1,562 G4-7S$P 2.6 5KS324SAA208 M9915 710 $3,272 G4-7U1 3.5
5KS284STE222 M7747 482 $1,950 G4-7S$P1 2.8 5KS324SAA218 M9916 710 $3,272 G4-7U1 3.5
5KS284XAA100 M8923 460 $2,804 G4-7UX1 3.22 5KS324SAA304 M9758 700 $3,668 G4-7U1 3.4
5KS284XAA114 M9575 460 $2,632 G4-7UX1 3.20 5KS324SAA305 M9158 679 $3,668 G4-7U1 3.4
5KS284XAA118 M9442 460 $2,632 G4-7UX1 3.20 5KS324SAA308 M9119 700 $3,668 G4-7U1 3.4
5KS284XAA200 M8915 460 $2,685 G4-7UX1 3.22 5KS324SAA404 M8950 649 $4,504 G4-7U1 3.4
5KS284XAA204 M9576 460 $2,514 G4-7UX1 3.20 5KS324SAA408 M9748 670 $4,504 G4-7U1 3.4
5KS284XAA208 M9443 460 $2,514 G4-7UX1 3.20 5KS324SS108D20 E9820 650 $2,938 G6-7S$ 8.13
5KS284XAA259 M6626 460 $2,842 G4-7UXHE 3.30 5KS324SS114D20 E9829 650 $2,938 G6-7S$ 8.13
5KS284XAA300 M8921 460 $3,050 G4-7UX1 3.22 5KS324SS115D26 E9162 650 $2,938 G6-7S$ 8.13
5KS284XAA304 M9569 460 $2,882 G4-7UX1 3.19 5KS324SS118D26 E996 650 $2,938 G6-7S$ 8.13
5KS284XAA308 M9436 460 $2,882 G4-7UX1 3.19 5KS324SS204D20 E9768 730 $2,823 G6-7S$ 8.13
5KS284XAA404 M9566 460 $3,617 G4-7UX1 3.19 5KS324SS205D24 E9163 730 $2,823 G6-7S$ 8.13
5KS284XAA408 M9433 460 $3,617 G4-7UX1 3.19 5KS324SS208 E9915 730 $2,823 G6-7S$ 8.13
5KS286ATE115 E755 445 $1,850 G4-7D$Z1 2.3 5KS324SS218D20 E9916 730 $2,823 G6-7S$ 8.13
5KS286ATE204 E7654 436 $1,425 G4-7D$Z1 2.3 5KS324SS304D8 E9758 710 $3,096 G6-7S$ 8.13
5KS286ATE205 E735 436 $1,425 G4-7D$Z1 2.3 5KS324SS305D16 E9158 710 $3,096 G6-7S$ 8.13
5KS286ATE206 E7763 436 $1,425 G4-7D$Z1 2.3 5KS324SS308D16 E9119 710 $3,096 G6-7S$ 8.13
5KS286ATE305 E7017 436 $1,549 G4-7D$Z1 2.2 5KS324SS408D8 E9748 710 $4,136 G6-7S$ 8.13
5KS286CSP114 E9631 510 $2,745 G6-7XP$ 8.11 5KS324ST5711 V832 650 $4,710 G6-7VIL 6.8
5KS286CSP115 E9666 510 $2,745 G6-7XP$ 8.11 5KS324ST6711 V841 730 $4,267 G6-7VIL 6.8
5KS286CSP204 E9632 510 $2,635 G6-7XP$ 8.11 5KS324STE105 M7712 650 $2,452 G4-7S$P 2.6
5KS286CSP205 E9675 510 $2,635 G6-7XP$ 8.11 5KS324STE115 M7711 640 $2,452 G4-7S$P 2.6
5KS286CSP304 E9628 510 $3,064 G6-7XP$ 8.11 5KS324STE205 M7734 650 $2,348 G4-7S$P 2.6
5KS286CSP305 E9683 510 $3,064 G6-7XP$ 8.11 5KS324STE215 M7735 640 $2,348 G4-7S$P 2.6
5KS286SAA100 M9904 510 $2,800 G4-7U1 3.8 5KS324XAA114 M9583 670 $4,176 G4-7UX1 3.20
5KS286SAA114 M9828 510 $2,653 G4-7U1 3.5 5KS324XAA118 M9450 670 $4,176 G4-7UX1 3.20
5KS286SAA115 M9159 510 $2,653 G4-7U1 3.5 5KS324XAA175 M8971 670 $4,389 G4-7UX1 3.22
5KS286SAA118 M995 510 $2,653 G4-7U1 3.5 5KS324XAA204 M9584 710 $4,051 G4-7UX1 3.20
5KS286SAA200 M9896 510 $2,671 G4-7U1 3.8 5KS324XAA208 M9451 710 $4,051 G4-7UX1 3.20
5KS286SAA204 M9764 510 $2,525 G4-7U1 3.5 5KS324XAA271 M6628 710 $4,465 G4-7UXHE 3.30
5KS286SAA205 M9160 510 $2,525 G4-7U1 3.5 5KS324XAA279 M8972 710 $4,264 G4-7UX1 3.22
5KS286SAA208 M9937 510 $2,525 G4-7U1 3.5 5KS324XAA304 M9577 700 $4,446 G4-7UX1 3.20
5KS286SAA300 M9902 510 $3,230 G4-7U1 3.8 5KS324XAA308 M9444 700 $4,446 G4-7UX1 3.20
5KS286SAA304 M9755 510 $3,083 G4-7U1 3.4 5KS324XAA404D1 M9574 670 $5,459 G4-7UX1 3.19
5KS286SAA305 M9155 510 $3,083 G4-7U1 3.4 5KS324XAA408 M9441 670 $5,459 G4-7UX1 3.19
5KS286SAA308 M9117 510 $3,083 G4-7U1 3.4 5KS324XS114 E9583 680 $3,526 G6-7S$8 8.15
5KS286SAA404 M9886 510 $3,684 G4-7U1 3.4 5KS324XS118 E9450 650 $3,526 G6-7S$8 8.15
5KS286SAA405 M9885 510 $3,684 G4-7U1 3.4 5KS324XS204 E9584 730 $3,388 G6-7S$8 8.15
5KS286SAA408 M9742 510 $3,684 G4-7U1 3.4 5KS324XS208 E9451 730 $3,388 G6-7S$8 8.15
5KS286SAE5705 V831 510 $2,460 G6-7VIL 6.8 5KS324XS304 E9577 710 $3,715 G6-7S$8 8.15
5KS286SAE6705 V840 510 $2,662 G6-7VIL 6.8 5KS324XS308 E9444 710 $3,715 G6-7S$8 8.15
5KS286STE105 M7750 475 $1,911 G4-7S$P 2.6 5KS324XS404 E9574 710 $4,963 G6-7S$8 8.15
5KS286STE112 M7722 522 $2,300 G4-7S$P1 2.8 5KS324XS408D17 E9441 710 $4,963 G6-7S$8 8.15
5KS286STE115 M7710 465 $1,911 G4-7S$P 2.6 5KS326ATE115 E757 692 $2,650 G4-7D$Z1 2.3
5KS286STE205 M7733 475 $1,760 G4-7S$P 2.6 5KS326ATE204 E7320 639 $2,066 G4-7D$Z1 2.3
5KS286STE222 M7748 508 $2,250 G4-7S$P1 2.8 5KS326ATE205 E737 639 $2,066 G4-7D$Z1 2.3
5KS286XAA100 M8924 510 $3,243 G4-7UX1 3.22 5KS326ATE215 E7254 639 $2,066 G4-7D$Z1 2.3
5KS286XAA114 M9579 510 $3,073 G4-7UX1 3.20 5KS326ATE305 E7022 639 $2,103 G4-7D$Z1 2.3
5KS286XAA118 M9446 510 $3,073 G4-7UX1 3.20 5KS326CS205 E9677 740 $4,262 G6-7XP$ 8.11

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.29
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS326CSP305 E9685 730 $4,361 G6-7XP$ 8.11 5KS364SS208D20 E9919 1060 $4,974 G6-7S$ 8.13
5KS326SAA108 M9823 700 $4,223 G4-7U1 3.5 5KS364SS218D20 E9921 1060 $4,974 G6-7S$ 8.13

Cross Reference Guide

5KS326SAA114 M9839 700 $4,223 G4-7U1 3.5 5KS364SS304 E9835 1070 $4,833 G6-7S$ 8.13
5KS326SAA115 M9164 700 $4,223 G4-7U1 3.5 5KS364SS308D15 E9124 1070 $4,833 G6-7S$ 8.13
5KS326SAA118 M997 700 $4,223 G4-7U1 3.5 5KS364SS408D8 E9767 1020 $5,788 G6-7S$ 8.13
5KS326SAA146 M8966 700 $4,436 G4-7U1 3.8 5KS364XAA114 M9591 940 $6,837 G4-7UX 3.20
5KS326SAA204 M9765 740 $3,836 G4-7U1 3.5 5KS364XAA118 M9458 940 $6,837 G4-7UX 3.20
5KS326SAA205 M9165 740 $3,836 G4-7U1 3.5 5KS364XAA204 M9592 1020 $6,616 G4-7UX 3.20
5KS326SAA208 M9917 740 $3,836 G4-7U1 3.5 5KS364XAA208 M9459 1020 $6,616 G4-7UX 3.20
5KS326SAA218 M9918 740 $3,836 G4-7U1 3.5 5KS364XAA249W8 M6631 1020 $7,556 G4-7UXHE 3.30
5KS326SAA271 M8967 740 $4,109 G4-7U1 3.8 5KS364XAA250W6 M6630 1020 $7,556 G4-7UXHE 3.30
5KS326SAA304 M9834 730 $4,184 G4-7U1 3.5 5KS364XAA304 M9585 1030 $6,633 G4-7UX 3.20
5KS326SAA305 M9161 730 $4,184 G4-7U1 3.5 5KS364XAA308 M9452 1030 $6,633 G4-7UX 3.20
5KS326SAA308 M9122 730 $4,184 G4-7U1 3.5 5KS364XAA404 M9582 1010 $8,073 G4-7UX 3.20
5KS326SAA404 M9762 710 $5,613 G4-7U1 3.4 5KS364XAA408 M9449 1010 $8,073 G4-7UX 3.20
5KS326SAA408 M9761 710 $5,613 G4-7U1 3.4 5KS364XS114 E9591 1000 $6,271 G6-7S$8 8.15
5KS326SS108D20 E9823 680 $3,814 G6-7S$ 8.13 5KS364XS118 E9458 1000 $6,271 G6-7S$8 8.15
5KS326SS114D20 E9839 680 $3,814 G6-7S$ 8.13 5KS364XS204 E9592 1060 $5,969 G6-7S$8 8.15
5KS326SS115D24 E9164 680 $3,814 G6-7S$ 8.13 5KS364XS208 E9459 1060 $5,969 G6-7S$8 8.15
5KS326SS118D24 E997 680 $3,814 G6-7S$ 8.13 5KS364XS304 E9585 1050 $5,800 G6-7S$8 8.15
5KS326SS204D20 E9765 740 $3,467 G6-7S$ 8.13 5KS364XS308 E9452 1070 $5,800 G6-7S$8 8.15
5KS326SS205D24 E9165 740 $3,467 G6-7S$ 8.13 5KS364XS404 E9582 1020 $6,946 G6-7S$8 8.15
5KS326SS208D20 E9917 740 $3,467 G6-7S$ 8.13 5KS364XS408 E9449 1020 $6,946 G6-7S$8 8.15
5KS326SS218D20 E9918 740 $3,467 G6-7S$ 8.13 5KS365ATE115 E759 812 $4,641 G4-7D$Z1 2.3
5KS326SS304D8 E9834 730 $3,566 G6-7S$ 8.13 5KS365ATE204 E7825 838 $3,269 G4-7D$Z1 2.3
5KS326SS305D15 E9161 730 $3,566 G6-7S$ 8.13 5KS365ATE205 E7391 838 $3,269 G4-7D$Z1 2.3
5KS326SS308D15 E9122 730 $3,566 G6-7S$ 8.13 5KS365ATE215 E7393 838 $3,269 G4-7D$Z1 2.3
5KS326SS408D8 E9761 730 $4,887 G6-7S$ 8.13 5KS365ATE308 E7026 838 $3,610 G4-7D$Z1 2.3
5KS326STE105 M7714 710 $3,173 G4-7S$P 2.6 5KS365LAA114A M7910 970 $7,067 G4-7S$P 2.6
5KS326STE115 M7713 700 $3,173 G4-7S$P 2.6 5KS365LAA118B M7912 970 $7,067 G4-7S$P 2.6
5KS326STE205 M7736 710 $2,884 G4-7S$P 2.6 5KS365LAA204A M7932 1,040 $6,834 G4-7S$P 2.6
5KS326STE215 M7737 700 $2,884 G4-7S$P 2.6 5KS365LAA208B M7934 1,040 $6,834 G4-7S$P 2.6
5KS326XAA114 M9587 700 $5,098 G4-7UX1 3.20 5KS365SAA114 M9830 970 $7,215 G4-7U 3.6
5KS326XAA118 M9454 700 $5,098 G4-7UX1 3.20 5KS365SAA118 M999 970 $7,215 G4-7U 3.6
5KS326XAA155 M8973 700 $5,311 G4-7UX1 3.22 5KS365SAA204 M9781 1080 $6,977 G4-7U 3.6
5KS326XAA204 M9588 740 $4,615 G4-7UX1 3.20 5KS365SAA208 M9922 1080 $6,977 G4-7U 3.6
5KS326XAA208 M9455 740 $4,615 G4-7UX1 3.20 5KS365SAA218 M9923 1080 $6,977 G4-7U 3.6
5KS326XAA253 M6629 740 $5,029 G4-7UXHE 3.30 5KS365SAA304 M9775 1070 $6,700 G4-7U 3.5
5KS326XAA263 M8974 740 $4,829 G4-7UX1 3.22 5KS365SAA308 M9126 1070 $6,700 G4-7U 3.5
5KS326XAA304 M9581 730 $4,962 G4-7UX1 3.20 5KS365SAA404 M9534 1090 $8,096 G4-7U 3.5
5KS326XAA308 M9448 730 $4,962 G4-7UX1 3.20 5KS365SAA408 M9770 1090 $8,096 G4-7U 3.5
5KS326XAA404 M9578 710 $6,538 G4-7UX1 3.20 5KS365SS114 E9830 990 $6,300 G6-7S$ 8.14
5KS326XAA408 M9445 710 $6,538 G4-7UX1 3.20 5KS365SS118D25 E999 990 $6,300 G6-7S$ 8.14
5KS326XS114 E9587 700 $4,577 G6-7S$ 8.13 5KS365SS204D20 E9781 1070 $6,305 G6-7S$ 8.14
5KS326XS118 E9454 680 $4,577 G6-7S$8 8.15 5KS365SS208 E9922 1070 $6,305 G6-7S$ 8.14
5KS326XS204 E9588 740 $4,160 G6-7S$8 8.15 5KS365SS218D20 E9923 1070 $6,305 G6-7S$ 8.14
5KS326XS208 E9455 740 $4,160 G6-7S$8 8.15 5KS365SS304D8 E9775 1050 $5,549 G6-7S$ 8.13
5KS326XS304 E9581 730 $4,279 G6-7S$8 8.15 5KS365SS308D14 E9126 1050 $5,549 G6-7S$ 8.13
5KS326XS308 E9448 730 $4,279 G6-7S$8 8.15 5KS365SS318D8 E9127 1050 $5,549 G6-7S$ 8.13
5KS326XS404 E9578 730 $5,864 G6-7S$8 8.15 5KS365SS404D8 E9534 1050 $7,145 G6-7S$ 8.13
5KS326XS408 E9445 730 $5,864 G6-7S$8 8.15 5KS365SS408D8 E9770 1050 $7,145 G6-7S$ 8.13
5KS364ATE115 E758 686 $3,533 G4-7D$Z1 2.3 5KS365XAA114 M8917 1020 $8,174 G4-7UX 3.20
5KS364ATE204 E7330 770 $2,684 G4-7D$Z1 2.3 5KS365XAA118 M9462 1020 $8,174 G4-7UX 3.20
5KS364ATE205 E7381 770 $2,684 G4-7D$Z1 2.3 5KS365XAA204 M9596 1090 $7,839 G4-7UX 3.20
5KS364ATE215 E7383 770 $2,684 G4-7D$Z1 2.3 5KS365XAA208 M9463 1090 $7,839 G4-7UX 3.20
5KS364ATE308 E7024 770 $3,091 G4-7D$Z1 2.3 5KS365XAA253W6 M6632 1090 $8,779 G4-7UXHE 3.30
5KS364LAA114A M7907 930 $5,757 G4-7S$P 2.6 5KS365XAA254W8 M6633 1090 $8,779 G4-7UXHE 3.30
5KS364LAA118B M7909 930 $5,757 G4-7S$P 2.6 5KS365XAA304 M9589 1070 $7,562 G4-7UX 3.20
5KS364LAA204A M7929 990 $5,637 G4-7S$P 2.6 5KS365XAA308 M9456 1070 $7,562 G4-7UX 3.20
5KS364LAA208B M7931 990 $5,637 G4-7S$P 2.6 5KS365XAA404 M9586 1090 $9,958 G4-7UX 3.20
5KS364SAA114 M9847 940 $5,877 G4-7U 3.6 5KS365XAA408 M9453 1090 $9,958 G4-7UX 3.20
5KS364SAA118 M998 940 $5,877 G4-7U 3.6 5KS365XS118 E9462 990 $7,875 G6-7S$8 8.15
5KS364SAA204 M9776 1020 $5,755 G4-7U 3.6 5KS365XS204 E9596 1070 $7,566 G6-7S$8 8.15
5KS364SAA208 M9919 1020 $5,755 G4-7U 3.6 5KS365XS208 E9463 1070 $7,566 G6-7S$8 8.15
5KS364SAA218 M9921 1020 $5,755 G4-7U 3.6 5KS365XS304 E9589 1050 $6,659 G6-7S$8 8.15
5KS364SAA304 M9835 1030 $5,771 G4-7U 3.5 5KS365XS308 E9456 1050 $6,659 G6-7S$8 8.15
5KS364SAA308 M9124 1030 $5,771 G4-7U 3.5 5KS365XS404 E9586 1050 $8,574 G6-7S$8 8.15
5KS364SAA404 M9766 1010 $6,564 G4-7U 3.5 5KS365XS408 E9453 1050 $8,574 G6-7S$8 8.15
5KS364SAA408 M9767 1010 $6,564 G4-7U 3.5 5KS404ATE118 E7501 1092 $5,774 G4-7D$Z1 2.3
5KS364SS114D20 E9847 1000 $5,017 G6-7S$ 8.13 5KS404ATE204 E7340 1090 $4,167 G4-7D$Z1 2.3
5KS364SS118D24 E998 1000 $5,017 G6-7S$ 8.13 5KS404ATE205 E7401 1090 $4,167 G4-7D$Z1 2.3
5KS364SS204D20 E9776 1060 $4,974 G6-7S$ 8.13 5KS404ATE215 E7257 1090 $4,167 G4-7D$Z1 2.3

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.30 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS404ATE308 E7029 1090 $4,467 G4-7D$Z1 2.3 5KS444SAA204 M9832 1970 $11,337 G4-7U 3.6
5KS404SAA304 M9837 1480 $7,794 G4-7U 3.6 5KS444SAA208 M9926 1970 $11,337 G4-7U 3.6
Cross Reference Guide

5KS404SAA308 M9128 1480 $7,794 G4-7U 3.6 5KS444SAA218 M9927 1970 $11,337 G4-7U 3.6
5KS404SAA404 M9535 1490 $9,769 G4-7U 3.5 5KS444SAA304 M9846 2060 $11,669 G4-7U 3.6
5KS404SAA408 M9773 1490 $9,769 G4-7U 3.5 5KS444SAA308 M9133 2060 $11,669 G4-7U 3.6
5KS404SS304D8 E9837 1530 $6,502 G6-7S$ 8.13 5KS444SAA404 M9537 1950 $15,015 G4-7U 3.6
5KS404SS308D15 E9128 1530 $6,502 G6-7S$ 8.13 5KS444SAA408 M9780 1950 $15,015 G4-7U 3.6
5KS404SS404D8 E9535 1500 $8,595 G6-7S$ 8.13 5KS444SS114D8 E9538 1990 $11,035 G6-7S$ 8.14
5KS404SS408D8 E9773 1500 $8,595 G6-7S$ 8.13 5KS444SS118 E9511 1990 $11,035 G6-7S$ 8.14
5KS404XAA304 M9593 1480 $8,830 G4-7UX 3.20 5KS444SS204D8 E9832 2050 $10,255 G6-7S$ 8.14
5KS404XAA308 M9460 1480 $8,830 G4-7UX 3.20 5KS444SS208 E9926 2050 $10,255 G6-7S$ 8.14
5KS404XAA404 M9590 1490 $12,015 G4-7UX 3.20 5KS444SS218D8 E9927 2050 $10,255 G6-7S$ 8.14
5KS404XAA408 M9457 1490 $12,015 G4-7UX 3.20 5KS444SS304D8 E9846 1920 $10,462 G6-7S$ 8.14
5KS404XS304 E9593 1530 $7,672 G6-7S$8 8.15 5KS444SS308D13 E9133 1920 $10,462 G6-7S$ 8.14
5KS404XS308 E9460 1530 $7,672 G6-7S$8 8.15 5KS444SS404D8 E9537 1980 $13,230 G6-7S$ 8.14
5KS404XS404 E9590 1500 $10,142 G6-7S$8 8.15 5KS444SS408D8 E9780 1930 $13,230 G6-7S$ 8.14
5KS404XS408 E9457 1500 $10,142 G6-7S$8 8.15 5KS444XAA118 M9470 1790 $13,446 G4-7UX 3.21
5KS405ATE118 E7502 1194 $7,024 G4-7D$Z1 2.3 5KS444XAA122 M8919 1790 $13,446 G4-7UX 3.21
5KS405ATE208 E741 1150 $4,992 G4-7D$Z1 2.3 5KS444XAA124 M8976 1880 $13,446 G4-7UX 3.21
5KS405ATE218 E7342 1150 $4,992 G4-7D$Z1 2.3 5KS444XAA204 M9697 1970 $12,434 G4-7UX 3.21
5KS405ATE308 E7032 1150 $5,316 G4-7D$Z1 2.3 5KS444XAA208 M9471 1970 $12,434 G4-7UX 3.21
5KS405LAA114B M7913 1,420 $9,151 G4-7S$P 2.7 5KS444XAA308 M9468 2060 $12,482 G4-7UX 3.21
5KS405LAA118C M7914 1,420 $9,151 G4-7S$P 2.7 5KS444XAA404 M9598 1950 $16,966 G4-7UX 3.20
5KS405LAA204A M7935 1,450 $8,441 G4-7S$P 2.7 5KS444XAA408 M9465 1950 $16,966 G4-7UX 3.20
5KS405LAA208B M7936 1,450 $8,441 G4-7S$P 2.7 5KS444XS118 E9470 1990 $13,794 G6-7S$8 8.16
5KS405SAA114 M9831 1530 $9,342 G4-7U 3.6 5KS444XS204 E9697 1990 $11,793 G6-7S$8 8.16
5KS405SAA118 M9510 1530 $9,342 G4-7U 3.6 5KS444XS208 E9471 1990 $11,793 G6-7S$8 8.16
5KS405SAA140 M9992 1530 $9,342 64-7U 3.6 5KS444XS304 E9694 1930 $12,031 G6-7S$8 8.16
5KS405SAA204 M9779 1480 $8,617 G4-7U 3.6 5KS444XS308 E9468 1920 $12,031 G6-7S$8 8.16
5KS405SAA208 M9924 1480 $8,617 G4-7U 3.6 5KS444XS404 E9598 1980 $15,215 G6-7S$8 8.15
5KS405SAA218 M9925 1480 $8,617 G4-7U 3.6 5KS444XS408 E9465 1980 $15,215 G6-7S$8 8.15
5KS405SAA304 M9868 1540 $8,664 G4-7U 3.6 5KS445ATE118 E7504 1800 $14,387 G4-7D$Z1 2.3
5KS405SAA308 M9131 1540 $8,664 G4-7U 3.6 5KS445ATE208 E743 1715 $10,150 G4-7D$Z1 2.3
5KS405SAA404 M9536 1570 $12,000 G4-7U 3.6 5KS445ATE218 E7360 1715 $10,150 G4-7D$Z1 2.3
5KS405SAA408 M9778 1570 $12,000 G4-7U 3.6 5KS445ATE308 E7036 1715 $8,268 G4-7D$Z1 2.3
5KS405SS114 E9831 1480 $8,442 G6-7S$ 8.14 5KS445LAA114A M7917 1,810 $13,728 G4-7S$P 2.7
5KS405SS118D8 E9510 1480 $8,442 G6-7S$ 8.14 5KS445LAA118B M7918 1,830 $13,728 G4-7S$P 2.7
5KS405SS204D8 E9779 1540 $7,790 G6-7S$ 8.14 5KS445LAA204A M7939 1,990 $12,339 G4-7S$P 2.7
5KS405SS208 E9924 1540 $7,790 G6-7S$ 8.14 5KS445LAA208B M7940 2,020 $12,339 G4-7S$P 2.7
5KS405SS218D8 E9925 1540 $7,790 G6-7S$ 8.14 5KS445SAA118 M9512 1860 $14,674 G4-7U 3.7
5KS405SS304 E9868 1490 $7,655 G6-7S$ 8.14 5KS445SAA121 M8955 1860 $14,674 G4-7U 3.7
5KS405SS308D14 E9131 1490 $7,655 G6-7S$ 8.14 5KS445SAA149 M9994 1860 $14,674 64-7U 3.7
5KS405SS404D8 E9536 1530 $9,934 G6-7S$ 8.13 5KS445SAA204 M9854 2060 $13,190 G4-7U 3.7
5KS405SS408D8 E9778 1530 $9,934 G6-7S$ 8.13 5KS445SAA208 M9928 2090 $13,190 G4-7U 3.7
5KS405XAA118 M9466 1530 $10,522 G4-7UX 3.21 5KS445SAA218 M9929 2090 $13,190 G4-7U 3.7
5KS405XAA123 M8918 1530 $10,522 G4-7UX 3.21 5KS445SAA304 M9870 2130 $14,057 G4-7U 3.6
5KS405XAA125 M8975 1530 $10,522 G4-7UX 3.21 5KS445SAA308 M9135 2130 $14,057 G4-7U 3.6
5KS405XAA204 M9693 1480 $9,651 G4-7UX 3.21 5KS445SAA408 M9782 2020 $19,025 G4-7U 3.6
5KS405XAA208 M9467 1480 $9,651 G4-7UX 3.21 5KS445SAA420 M8953 2020 $19,025 G4-7U 3.6
5KS405XAA304 M9597 1540 $9,698 G4-7UX 3.20 5KS445SS118D8 E9512 1990 $13,257 G6-7S$ 8.14
5KS405XAA308 M9464 1540 $9,698 G4-7UX 3.20 5KS445SS204D8 E9854 2050 $11,922 G6-7S$ 8.14
5KS405XAA404 M9594 1570 $13,560 G4-7UX 3.20 5KS445SS208D8 E9928 2050 $11,922 G6-7S$ 8.14
5KS405XAA408 M9461 1570 $13,560 G4-7UX 3.20 5KS445SS218D8 E9929 2050 $11,922 G6-7S$ 8.14
5KS405XS118 E9466 1480 $10,553 G6-7S$8 8.16 5KS445SS304D8 E9870 1960 $12,850 G6-7S$ 8.14
5KS405XS204 E9693 1540 $9,192 G6-7S$8 8.16 5KS445SS308D13 E9135 1960 $12,850 G6-7S$ 8.14
5KS405XS208 E9467 1540 $9,192 G6-7S$8 8.16 5KS445SS408D8 E9782 2060 $16,643 G6-7S$ 8.14
5KS405XS304 E9597 1490 $9,033 G6-7S$8 8.15 5KS445XAA118 M9474 1930 $15,916 G4-7UX 3.21
5KS405XS308 E9464 1490 $9,033 G6-7S$8 8.15 5KS445XAA122 M8920 1930 $15,916 G4-7UX 3.21
5KS405XS404 E9594 1530 $11,722 G6-7S$8 8.15 5KS445XAA125 M8977 2000 $15,916 G4-7UX 3.21
5KS405XS408 E9461 1530 $11,722 G6-7S$8 8.15 5KS445XAA204 M9384 2060 $14,287 G4-7UX 3.21
5KS444ATE118 E7503 1590 $12,368 G4-7D$Z1 2.3 5KS445XAA208 M9475 2090 $14,287 G4-7UX 3.21
5KS444ATE208 E742 1494 $7,209 G4-7D$Z1 2.3 5KS445XAA304 M9698 2130 $14,871 G4-7UX 3.21
5KS444ATE218 E7259 1494 $7,209 G4-7D$Z1 2.3 5KS445XAA308 M9472 2130 $14,871 G4-7UX 3.21
5KS444ATE308 E7034 1494 $6,733 G4-7D$Z1 2.3 5KS445XAA404 M9695 2020 $21,498 G4-7UX 3.21
5KS444LAA114B M7915 1,780 $11,416 G4-7S$P 2.7 5KS445XAA408 M9469 2020 $21,498 G4-7UX 3.21
5KS444LAA118C M7916 1,780 $11,953 G4-7S$P 2.7 5KS445XS118 E9474 1990 $16,571 G6-7S$8 8.16
5KS444LAA204A M7937 1,860 $10,606 G4-7S$P 2.7 5KS445XS204D18 E9384 2050 $13,710 G6-7S$8 8.16
5KS444LAA208B M7938 1,880 $10,606 G4-7S$P 2.7 5KS445XS208 E9475 2050 $13,710 G6-7S$8 8.16
5KS444SAA114 M9538 1790 $12,203 G4-7U 3.6 5KS445XS304 E9698 1960 $14,778 G6-7S$8 8.16
5KS444SAA118 M9511 1790 $12,203 G4-7U 3.6 5KS445XS308 E9472 1960 $14,778 G6-7S$8 8.16
5KS444SAA150 M9993 1790 $12,203 64-7U 3.6 5KS445XS404 E9695 2060 $19,139 G6-7S$8 8.16

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.

 Cross Reference Guide

Model Number to Catalog Number

Wt List Price Page Wt List Price Page 13.31
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
5KS445XS408 E9469 2060 $19,139 G6-7S$8 8.16 5KS449XAA123 M8943 2770 $25,052 G4-7UX 3.21
5KS447ATE208 E7272 2100 $12,600 G4-7D$Z1 2.3 5KS449XAA124 M8944 2770 $25,052 G4-7UX 3.21

Cross Reference Guide

5KS447ATE218 E7370 2100 $12,600 G4-7D$Z1 2.3 5KS449XAA125 M8979 2770 $25,052 G4-7UX 3.21
5KS447ATE308 E7962 2100 $9,166 G4-7D$Z1 2.3 5KS449XAA224 M8945 2790 $20,436 G4-7UX 3.21
5KS447LAA114B M7919 2,420 $17,379 G4-7S$P 2.7 5KS449XAA225 M8946 2790 $20,436 G4-7UX 3.21
5KS447LAA118C M7920 2,420 $17,379 G4-7S$P 2.7 5KS449XAA322 M8940 3070 $20,142 G4-7UX 3.21
5KS447LAA204B M7941 2,560 $15,478 G4-7S$P 2.7 5KS449XAA323 M8941 3070 $20,142 G4-7UX 3.21
5KS447LAA208C M7942 2,580 $15,478 G4-7S$P 2.7 5KS449XAA409 M8942 3120 $27,500 G4-7UX 3.21
5KS447SAA118 M9961 2560 $18,577 G4-7U 3.7 5KS449XAA420 M8937 3150 $26,105 G4-7UX 3.21
5KS447SAA120 M8957 2560 $18,577 G4-7U 3.7 5KS449XAA422 M8938 3120 $26,105 G4-7UX 3.21
5KS447SAA125 M9995 2560 $18,577 64-7U 3.7 5KSM81FFL0002 5113 2 $28 G3-1CON 8.3
5KS447SAA201 M9991 2610 $16,545 G4-7U 3.7 5KSM81FFL0003 5213 2 $25 G3-1CON 8.3
5KS447SAA204 M9959 2610 $16,545 G4-7U 3.7 5KSM81FFL0004 5214 2 $25 G3-1CON 8.3
5KS447SAA208 M9958 2610 $16,545 G4-7U 3.7 5KSM81FFL0005 5223 2 $27 G3-1CON 8.3
5KS447SAA304 M9869 2860 $17,030 G4-7U 3.7 5KSM81FFL0006 5224 2 $27 G3-1CON 8.3
5KS447SAA308 M9137 2860 $17,030 G4-7U 3.7 5KSM81FFL0065 5109 4 $22 G3-1CON 8.3
5KS447SAA408 M9784 2580 $21,185 G4-7U 3.6 5KSM81FFL0068 5108 2 $27 G3-1CON 8.3
5KS447SAA420 M8954 2580 $21,185 G4-7U 3.6 5KSM81FFL1000 5413 2 $28 G3-1CON 8.3
5KS447SS118D8 E9961 2580 $16,770 G6-7S$ 8.14 5KSM81FFL1002 5313 2 $27 G3-1CON 8.3
5KS447SS204D8 E9959 2520 $14,501 G6-7S$ 8.14 5KSM81FFL1003 5314 2 $27 G3-1CON 8.3
5KS447SS208D8 E9958 2520 $14,501 G6-7S$ 8.14 5KSM81FFL1004 5414 2 $28 G3-1CON 8.3
5KS447SS304D8 E9869 2920 $14,377 G6-7S$ 8.14 5KSM81FFL1005 5423 2 $30 G3-1CON 8.3
5KS447SS308D11 E9137 2920 $14,377 G6-7S$ 8.14 5KSM81FFL1006 5424 2 $30 G3-1CON 8.3
5KS447SS408D8 E9784 2550 $19,308 G6-7S$ 8.14 5KSM81FFL3000S 5813 3 $36 G3-1CON 8.3
5KS447XAA118 M9477 2560 $19,819 G4-7UX 3.21 5KSM81FFL3001S 5814 3 $36 G3-1CON 8.3
5KS447XAA122 M8939 2560 $19,819 G4-7UX 3.21 5KSM81FFL3002S 5823 3 $38 G3-1CON 8.3
5KS447XAA124 M8978 2630 $19,819 G4-7UX 3.21 5KSM81FFL3003S 5824 3 $38 G3-1CON 8.3
5KS447XAA204 M9387 2800 $17,614 G4-7UX 3.21 5KSM81HFL0007 5111 2 $30 G3-1CON 8.3
5KS447XAA208 M9478 2800 $17,614 G4-7UX 3.21 5KSM81HFL0008 5211 2 $28 G3-1CON 8.3
5KS447XAA304 M9385 2860 $18,108 G4-7UX 3.21 5KSM81HFL0009 5212 2 $28 G3-1CON 8.3
5KS447XAA308 M9476 2860 $18,108 G4-7UX 3.21 5KSM81HFL0010 5221 3 $30 G3-1CON 8.3
5KS447XAA404 M9699 2580 $23,939 G4-7UX 3.21 5KSM81HFL0011 5222 3 $30 G3-1CON 8.3
5KS447XAA408 M9473 2580 $23,939 G4-7UX 3.21 5KSM81HFL1001 5411 3 $31 G3-1CON 8.3
5KS447XS118 E9477 2580 $20,963 G6-7S$8 8.16 5KSM81HFL1007 5311 3 $30 G3-1CON 8.3
5KS447XS204D18 E9387 2690 $16,386 G6-7S$8 8.16 5KSM81HFL1008 5312 4 $30 G3-1CON 8.3
5KS447XS208 E9478 2690 $16,386 G6-7S$8 8.16 5KSM81HFL1009 5412 3 $31 G3-1CON 8.3
5KS447XS304D16 E9385 2940 $16,246 G6-7S$8 8.16 5KSM81HFL1010 5421 3 $33 G3-1CON 8.3
5KS447XS308 E9476 2920 $16,246 G6-7S$8 8.16 5KSM81HFL1011 5422 3 $33 G3-1CON 8.3
5KS447XS404 E9699 2860 $21,818 G6-7S$8 8.16 5KSM81HFL3004T 5811 4 $42 G3-1CON 8.3
5KS447XS408 E9473 2860 $21,818 G6-7S$8 8.16 5KSM81HFL3005T 5812 4 $42 G3-1CON 8.3
5KS449ATE208 E7273 2150 $15,541 G4-7D$Z1 2.3 5KSM81HFL3006T 5821 4 $44 G3-1CON 8.3
5KS449ATE308 E7963 2150 $14,829 G4-7D$Z1 2.3 5KSM81HFL3007T 5822 6 $44 G3-1CON 8.3
5KS449LAA114A M7921 2,580 $22,392 G4-7S$P 2.7 5KSM92HFL2004S 1341 9 $156 G3-1CON 8.2
5KS449LAA118B M7922 2,580 $22,392 G4-7S$P 2.7 5KSM92KFL1009S 1442 9 $140 G3-1CON 8.2
5KS449LAA204A M7943 2,660 $18,099 G4-7S$P 2.7 5KSM92KFL2003S 1441 7 $137 G3-1CON 8.2
5KS449LAA208B M7944 2,660 $18,099 G4-7S$P 2.7 5KSM92KFL2005S 1431 6 $137 G3-1CON 8.2
5KS449SAA118 M9514 2770 $23,935 G4-7U 3.7 5KSM92KFL2007S 1332 7 $159 G3-1CON 8.2
5KS449SAA122 M8959 2770 $23,935 G4-7U 3.7 5KSM92KFL2008S 1336 9 $94 G3-1CON 8.2
5KS449SAA123 M8960 2790 $29,681 G4-7U 3.7 5KSM92KFL2009S 1432 7 $140 G3-1CON 8.2
5KS449SAA124 M8961 2790 $29,681 G4-7U 3.7 5KSM92KFL2011S 1331 7 $156 G3-1CON 8.2
5KS449SAA146 M9996 2770 $23,935 G4-7U 3.7 5KSM92KFL2012S 1342 7 $159 G3-1CON 8.2
5KS449SAA201 M9988 3010 $19,347 G4-7U 3.7 5KSM92KFL3006S 1232 7 $167 G3-1CON 8.2
5KS449SAA202 M9989 3010 $19,347 G4-7U 3.7 5PY59EY2 D120 5 $681 GO-7PTC 7.8
5KS449SAA204 M9851 2790 $19,347 G4-7U 3.7 5PY59EY3 D121 4 $681 GO-7PTC 7.8
5KS449SAA208 M9933 2790 $19,347 G4-7U 3.7 5PY59EY4 D246 5 $818 GO-7PTC 7.8
5KS449SAA209 M9906 2980 $22,654 G4-7U 3.7 5PY59JY1 D122 8 $1,335 GO-7PTC 7.8
5KS449SAA212 M9990 2980 $22,654 G4-7U 3.7 5PY59JY2 D123 7 $1,335 GO-7PTC 7.8
5KS449SAA223 M8962 3030 $22,654 G4-7U 3.7 5PY59JY23 D124 7 $1,335 GO-7PTC 7.8
5KS449SAA301 M8963 3150 $24,120 G4-7U 3.7 5PY59JY24 D125 7 $1,335 GO-7PTC 7.8
5KS449SAA309 M9139 3070 $19,053 G4-7U 3.7 5PY59JY3 D252 7 $1,602 GO-7PTC 7.8
5KS449SAA319 M9141 3070 $19,053 G4-7U 3.7 5PY59JY84 D251 7 $1,635 GO-7PTC 7.8
5KS449SAA328 M9845 3070 $19,053 G4-7U 3.7 5PY59JY85 D250 8 $1,635 GO-7PTC 7.8
5KS449SAA408 M9785 3150 $23,102 G4-7U 3.7 5SK284CSP115 E9665 460 $2,424 G6-7XP$ 8.11
5KS449SAA420 M8956 3120 $23,102 G4-7U 3.7 893A666AAG02 A569 $973 GO-2SK3 7.23
5KS449SS118D8 E9514 2620 $21,150 G6-7S$ 8.14 893A690AAG01 A565 $370 GO-2SK3 7.23
5KS449SS204D8 E9851 2660 $18,192 G6-7S$ 8.14 BC48JB3080 D392 49 $780 GO-1GLF 8.6
5KS449SS208D8 E9933 2660 $18,192 G6-7S$ 8.14 BC48JB3084 D398 45 $760 GO-1GLF 8.6
5KS449SS209D8 E9906 2890 $19,113 G6-7S$ 8.14 BC49JB1132 D394 55 $880 GO-1GLF 8.6
5KS449SS309D14 E9139 2920 $17,600 G6-7S$ 8.14 BC49JB1134 D395 55 $880 GO-1GLF 8.6
5KS449SS319D12 E9141 2920 $17,600 G6-7S$ 8.14 BC49JB1144 D396 53 $800 GO-1GLF 8.6
5KS449SS328D8 E9845 2920 $17,600 G6-7S$ 8.14 BC49JB1149 D397 54 $800 GO-1GLF 8.6

Data subject to change without notice. GEP-500T 03/08. www.gemotors.com

 Cross Reference Guide

Model Number to Catalog Number

13.32 Wt List Price Page Wt List Price Page
Model Cat No. (lbs) Price Symbol Number Model Cat No. (lbs) Price Symbol Number
BC58JBS6381 D390 35 $680 GO-1GLF 8.6 Refer to factory P207 8100 $131,134 G8-9PTAC 5.5
BC58JBS6384 D391 35 $680 GO-1GLF 8.6 Refer to factory P208 8750 $122,740 G8-9PTAC 5.5
Cross Reference Guide

CAT#A249 A249 $188 G4-7KITS 2.11 Refer to factory P209 8750 $112,634 G8-9PTAC 5.5
CAT#A641 A641 $2,016 GO-2KITS 7.24 Refer to factory P210 8100 $141,240 G8-9PTAC 5.5
CAT#A642 A642 $2,215 GO-2KITS 7.24 Refer to factory P211 8100 $131,134 G8-9PTAC 5.5
CAT#A643 A643 $2,518 GO-2KITS 7.24 Refer to factory P212 8750 $124,123 G8-9PTAC 5.5
CAT#A644 A644 $2,417 GO-2KITS 7.24 Refer to factory P213 8750 $114,017 G8-9PTAC 5.5
CAT#A645 A645 $2,299 GO-2KITS 7.24 Refer to factory P214 9950 $156,830 G8-9PTAC 5.5
CAT#A646 A646 $2,643 GO-2KITS 7.24 Refer to factory P215 8750 $141,244 G8-9PTAC 5.5
CAT#A686 A686 $1,708 GO-2KITS 7.24 Refer to factory P216 8750 $129,520 G8-9PTAC 5.5
KS447SS280D8 E9991 2520 $14,501 G6-7S$ 8.14 Refer to factory P217 9950 $175,454 G8-9PTAC 5.5
KS449SS2210D8 E9988 2660 $18,192 G6-7S$ 8.14 Refer to factory P218 10500 $144,827 G8-9PTAC 5.5
KS449SS2211D8 E9989 2660 $18,192 G6-7S$ 8.14 Refer to factory P219 10500 $133,103 G8-9PTAC 5.5
KS449SS2212D8 E9990 2890 $19,113 G6-7S$ 8.14 Refer to factory P220 9950 $190,720 G8-9PTAC 5.5
Refer to factory P100 7500 $100,211 G8-9PWII 5.3 Refer to factory P221 10500 $156,772 G8-9PTAC 5.5
Refer to factory P101 7500 $90,103 G8-9PWII 5.3 Refer to factory P222 10500 $145,046 G8-9PTAC 5.5
Refer to factory P102 7000 $118,501 G8-9PWII 5.3 Refer to factory P223 11500 $205,985 G8-9PTAC 5.5
Refer to factory P103 7000 $108,393 G8-9PWII 5.3 Refer to factory P224 10500 $167,515 G8-9PTAC 5.5
Refer to factory P104 7500 $103,933 G8-9PWII 5.3 Refer to factory P225 10500 $155,792 G8-9PTAC 5.5
Refer to factory P105 7500 $93,825 G8-9PWII 5.3 Refer to factory P226 11500 $174,407 G8-9PTAC 5.5
Refer to factory P106 8500 $109,523 G8-9PWII 5.3 Refer to factory P227 13500 $208,756 G8-9PTAC 5.5
Refer to factory P107 7500 $108,588 G8-9PWII 5.3 Refer to factory P228 13500 $197,032 G8-9PTAC 5.5
Refer to factory P108 7500 $98,482 G8-9PWII 5.3 Refer to factory P229 12500 $178,023 G8-9PTAC 5.5
Refer to factory P109 8500 $112,912 G8-9PWII 5.3 Refer to factory P230 17500 $221,521 G8-9PTAC 5.5
Refer to factory P110 9200 $116,039 G8-9PWII 5.3 Refer to factory P231 17500 $209,797 G8-9PTAC 5.5
Refer to factory P111 9200 $105,932 G8-9PWII 5.3 Refer to factory P232 13500 $218,111 G8-9PTAC 5.5
Refer to factory P112 8500 $118,563 G8-9PWII 5.3 Refer to factory P233 17500 $179,625 G8-9PTAC 5.5
Refer to factory P113 9200 $125,351 G8-9PWII 5.3 Refer to factory P234 17500 $166,596 G8-9PTAC 5.5
Refer to factory P114 9200 $115,245 G8-9PWII 5.3 Refer to factory P235 13500 $226,383 G8-9PTAC 5.5
Refer to factory P115 9300 $155,397 G8-9PWII 5.3 Refer to factory P236 17500 $186,974 G8-9PTAC 5.5
Refer to factory P116 12000 $136,806 G8-9PWII 5.3 Refer to factory P237 17500 $173,947 G8-9PTAC 5.5
Refer to factory P117 12000 $124,678 G8-9PWII 5.3 Refer to factory P238 17500 $194,323 G8-9PTAC 5.5
Refer to factory P118 9300 $161,378 G8-9PWII 5.3 Refer to factory P239 17500 $181,296 G8-9PTAC 5.5
Refer to factory P119 12000 $143,638 G8-9PWII 5.3 Refer to factory P240 14000 $229,691 G8-9PTAC 5.5
Refer to factory P120 12000 $131,509 G8-9PWII 5.3 Refer to factory P241 17500 $201,674 G8-9PTAC 5.5
Refer to factory P121 9300 $170,017 G8-9PWII 5.3 Refer to factory P242 17500 $188,647 G8-9PTAC 5.5
Refer to factory P122 16000 $170,425 G8-9PWII 5.3 Refer to factory Q100 9700 $156,830 G8-9QT 5.4
Refer to factory P123 16000 $157,398 G8-9PWII 5.3 Refer to factory Q101 9500 $141,244 G8-9QT 5.4
Refer to factory P124 13900 $203,839 G8-9PWII 5.3 Refer to factory Q102 9500 $129,520 G8-9QT 5.4
Refer to factory P125 16000 $171,892 G8-9PWII 5.3 Refer to factory Q103 11400 $175,454 G8-9QT 5.4
Refer to factory P126 16000 $158,866 G8-9PWII 5.3 Refer to factory Q104 10100 $144,827 G8-9QT 5.4
Refer to factory P127 16000 $177,764 G8-9PWII 5.3 Refer to factory Q105 10100 $133,103 G8-9QT 5.4
Refer to factory P128 16000 $164,738 G8-9PWII 5.3 Refer to factory Q106 12500 $190,720 G8-9QT 5.4
Refer to factory P129 13900 $209,516 G8-9PWII 5.3 Refer to factory Q107 11000 $156,772 G8-9QT 5.4
Refer to factory P130 16000 $186,572 G8-9PWII 5.3 Refer to factory Q108 11000 $145,046 G8-9QT 5.4
Refer to factory P131 16000 $173,545 G8-9PWII 5.3 Refer to factory Q109 13000 $204,474 G8-9QT 5.4
Refer to factory P132 13900 $220,871 G8-9PWII 5.3 Refer to factory Q110 12100 $165,882 G8-9QT 5.4
Refer to factory P133 16000 $196,847 G8-9PWII 5.3 Refer to factory Q111 12100 $153,754 G8-9QT 5.4
Refer to factory P134 16000 $183,821 G8-9PWII 5.3 Refer to factory Q112 13600 $205,985 G8-9QT 5.4
Refer to factory P135 13900 $228,439 G8-9PWII 5.3 Refer to factory Q113 12700 $167,515 G8-9QT 5.4
Refer to factory P200 8100 $139,035 G8-9PTAC 5.5 Refer to factory Q114 12700 $155,792 G8-9QT 5.4
Refer to factory P201 8100 $128,927 G8-9PTAC 5.5 Refer to factory Q115 14100 $208,756 G8-9QT 5.4
Refer to factory P202 8100 $140,136 G8-9PTAC 5.5 Refer to factory Q116 14100 $197,032 G8-9QT 5.4
Refer to factory P203 8100 $130,030 G8-9PTAC 5.5 Refer to factory Q117 15000 $221,521 G8-9QT 5.4
Refer to factory P204 7000 $120,897 G8-9PTAC 5.5 Refer to factory Q118 15000 $209,797 G8-9QT 5.4
Refer to factory P205 7000 $110,791 G8-9PTAC 5.5
Refer to factory P206 8100 $141,240 G8-9PTAC 5.5

www.gemotors.com Data subject to change without notice. GEP-500T 03/08.