Residensi Adelia 2, B-22-15, Jalan Persiaran Bangi Avenue 2, Taman Bangi Avenue, 43000 Kajang Selangor .XLSX - Compressed
Residensi Adelia 2, B-22-15, Jalan Persiaran Bangi Avenue 2, Taman Bangi Avenue, 43000 Kajang Selangor .XLSX - Compressed
INSPECTION REPORTS
Defect 1
AREA W - Wall
CODE F-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 2
AREA W - Wall
CODE F-W-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA W - Wall
CODE H-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 2
AREA D - Door
CODE H-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA DF - Door frame
CODE H-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 4
AREA FT - Floor tiles
CODE H-FT-6
DEFECTS HT - Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 5
AREA FT - Floor tiles
CODE H-FT-CP
DEFECTS CP -Chipped
CORRECTIVE CP - The chipped tiles need to
change with the new one
ACTION
DONE / REMARKS
(By Contractor)
Defect 6
AREA W - Wall
CODE H-W-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 7
AREA FT - Floor tiles
CODE H-FT-F
DEFECTS F - Uneven filler
CORRECTIVE F - Need to apply the filler back
and make sure good finishing
ACTION
DONE / REMARKS
(By Contractor)
Defect 8
AREA C - Ceiling
CODE H-C-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA SD - Sliding door
CODE B-SD-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 2
AREA FT - Floor tiles
CODE B-FT-CP
DEFECTS CP -Chipped
CORRECTIVE CP - The chipped tiles need to
change with the new one
ACTION
DONE / REMARKS
(By Contractor)
Defect 3
AREA GL - Grille
CODE B-GL-D
DEFECTS D - Dented
CORRECTIVE D - Need to fix the dented part
ACTION
DONE / REMARKS
(By Contractor)
Defect 4
AREA W - Wall
CODE B-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 5
AREA GL - Grille
CODE B-G-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA KC - Kitchen cabinet
CODE K-KC-NA
DEFECTS NA - Not alligned
CORRECTIVE NA - Re-install and make sure it is
allign
ACTION
DONE / REMARKS
(By Contractor)
Defect 2
AREA W T - Wall tiles
CODE K-WT-CP
DEFECTS CP -Chipped
CORRECTIVE CP - The chipped tiles need to
change with the new one
ACTION
DONE / REMARKS
(By Contractor)
Defect 3
AREA WF - Window frame
CODE K-WF-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 4
AREA W T - Wall tiles
CODE K-WT-F
DEFECTS F - Uneven filler
CORRECTIVE F - Need to apply the filler back
and make sure good finishing
ACTION
DONE / REMARKS
(By Contractor)
Defect 5
AREA C - Ceiling
CODE K-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 6
AREA FT - Floor tiles
CODE K-FT-1
DEFECTS HT - Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA D - Door
CODE MB-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA DF - Door frame
CODE MB-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA FT - Floor tiles
CODE MB-FT-F
DEFECTS F - Uneven filler
CORRECTIVE F - Need to apply the filler back
and make sure good finishing
ACTION
DONE / REMARKS
(By Contractor)
Defect 4
AREA WF - Window frame
CODE MB-WF-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 5
AREA FT - Floor tiles
CODE MB-FT-2
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 6
AREA WW - Window
CODE MB-WW-ST
DEFECTS ST - Stuck
CORRECTIVE ST - Check what has caused it and
fix it
ACTION
DONE / REMARKS
(By Contractor)
Defect 7
AREA W - Wall
CODE MB-W-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 8
AREA W - Wall
CODE MB-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 9
AREA C - Ceiling
CODE MB-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 10
AREA C - Ceiling
CODE MB-C-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 11
AREA C - Ceiling
CODE MB-C-WM
DEFECTS WM - Watermark
CORRECTIVE WM - Check the source of leakage
and fix it. For water mark area
ACTION need to sand down and repaint
with the same coded colour
DONE / REMARKS
(By Contractor)
Defect 12
AREA AC - Air conditioner
CODE MB-AC-LABEL
DEFECTS LABEL - NOT COLD
CORRECTIVE Label - Recheck and fix the faulty
problems and ensure it is well
ACTION function.
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA D - Door
CODE TM-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA D - Door
CODE TM-D-CP
DEFECTS CP -Chipped
CORRECTIVE CP - Wood: Fill the chipped area
with wood filler sand down and
ACTION repaint with th coded colour or
change new
DONE / REMARKS
(By Contractor)
Defect 3
AREA DF - Door frame
CODE TM-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 4
AREA W T - Wall tiles
CODE TM-WT-8
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 5
AREA W T - Wall tiles
CODE TM-WT-CP
DEFECTS CP -Chipped
CORRECTIVE CP - The chipped tiles need to
change with the new one
ACTION
DONE / REMARKS
(By Contractor)
Defect 6
AREA STC - Stop cock
CODE TM-STC-L
DEFECTS L - Leaking
CORRECTIVE L - Check the source of leakage. If
the part is broken then need to
ACTION change and double test check.
DONE / REMARKS
(By Contractor)
Defect 7
AREA FTK - Flush tank
CODE TM-FTK-L
DEFECTS L - Leaking
CORRECTIVE L - Check the source of leakage. If
the part is broken then need to
ACTION change and double test check.
DONE / REMARKS
(By Contractor)
Defect 8
AREA C - Ceiling
CODE TM-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA D - Door
CODE B2-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA DF - Door frame
CODE B2-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA FT - Floor tiles
CODE B2-FT-8
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 4
AREA W - Wall
CODE B2-W-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 5
AREA W - Wall
CODE B2-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 6
AREA WF - Window frame
CODE B2-WF-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 7
AREA C - Ceiling
CODE B2-C-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 8
AREA C - Ceiling
CODE B2-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA DF - Door frame
CODE T2-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA D - Door
CODE T2-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA FTK - Flush tank
CODE T2-FTK-SK
DEFECTS SK - Shaky
CORRECTIVE SK - Shaky – Reinstall the fitting
and install back. Make sure its
ACTION tightened and firm
DONE / REMARKS
(By Contractor)
Defect 4
AREA WF - Window frame
CODE T2-WF-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 5
AREA W T - Wall tiles
CODE T2-WT-12
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 6
AREA C - Ceiling
CODE T2-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 7
AREA STC - Stop cock
CODE T2-STC-ST
DEFECTS ST - Stuck
CORRECTIVE ST - Check what has caused it and
fix it
ACTION
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA D - Door
CODE B3-D-CP
DEFECTS CP -Chipped
CORRECTIVE CP - Wood: Fill the chipped area
with wood filler
ACTION
DONE / REMARKS
(By Contractor)
Defect 2
AREA D - Door
CODE B3-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA DF - Door frame
CODE B3-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 4
AREA FT - Floor tiles
CODE B3-FT-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 5
AREA W - Wall
CODE B3-W-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 6
AREA WF - Window frame
CODE B3-WF-T
DEFECTS T - Stain
CORRECTIVE T - Remove the stain and clean the
affected area
ACTION
DONE / REMARKS
(By Contractor)
Defect 7
AREA C - Ceiling
CODE B3-C-C
DEFECTS C - Crack
CORRECTIVE C - Wall: Cut along the hairline
crack. Install fibre/wire mesh and
ACTION fill the area with skim filler. Sand
down the surface and repaint with
same colour code.
DONE / REMARKS
(By Contractor)
Defect 8
AREA C - Ceiling
CODE B3-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA DF - Door frame
CODE T3-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA D - Door
CODE T3-D-CP
DEFECTS CP -Chipped
CORRECTIVE CP - Wood: Fill the chipped area
with wood filler
ACTION
DONE / REMARKS
(By Contractor)
Defect 3
AREA D - Door
CODE T3-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 4
AREA W T - Wall tiles
CODE T3-WT-CP
DEFECTS CP -Chipped
CORRECTIVE CP - The chipped tiles need to
change with the new one
ACTION
DONE / REMARKS
(By Contractor)
Defect 5
AREA FT - Floor tiles
CODE T3-FT-2
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 6
AREA W T - Wall tiles
CODE T3-WT-13
DEFECTS Hollow tiles
CORRECTIVE HT - Refer no. on label for
quantity tiles defect. For hollow
ACTION tiles need to replace with a new
tile with same code. Make sure the
tile alignment is consistent and
tile adhesive is fully spread. Test
for tile hollowness.
DONE / REMARKS
(By Contractor)
Defect 7
AREA C - Ceiling
CODE T3-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 8
AREA FTK - Flush tank
CODE T3-FTK-L
DEFECTS L - Leaking
CORRECTIVE L - Check the source of leakage. If
the part is broken then need to
ACTION change and double test check.
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES
Defect 1
AREA D - Door
CODE Y-D-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 2
AREA DF - Door frame
CODE Y-DF-P
DEFECTS P - Uneven painted
CORRECTIVE P - For uneven painted. Need to
re-paint with the same coded
ACTION colour and make sure the same
tone
DONE / REMARKS
(By Contractor)
Defect 3
AREA W - Wall
CODE Y-W-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
Defect 4
AREA C - Ceiling
CODE Y-C-S
DEFECTS S - Uneven skim/plaster
CORRECTIVE S - Apply skim coat and sand the
affected area. Repaint with the
ACTION same colour code. Make sure
surface is smooth and even
DONE / REMARKS
(By Contractor)
VIEW PICTURES
VIEW PICTURES