Scribd
Upload
31 views

C Dac Ecam

Uploaded by

francismburu448
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views

C Dac Ecam

Uploaded by

francismburu448
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

© TVETCDACC 2024

071305T4EIN
ELECTRICAL INSTALLATION LEVEL 5
ENG/OS/EI/CC/04/5
Prepare and Interpret Technical Drawing
July/August 2024
Time: 3 Hours

TVET CURRICULUM DEVELOPMENT, ASSESSMENT AND CERTIFICATION


COUNCIL (TVET CDACC)om
.c
et
tv

WRITTEN ASSESSMENT
sy
ea

3 HOURS

INSTRUCTIONS TO CANDIDATE:
1. This paper consists of TWO sections: A and B
2. Answer ALL questions in sections A and any THREE questions in section B on the
answer booklet provided.
3. Marks for each question are indicated in the brackets.
4. Do not write on the question paper
5. Answer all questions in English.

This paper consists SIX (6) printed pages.


Candidate should check the question paper to ascertain that all pages are
printed as indicated and that no questions are missing.

Page 1 of 6
© TVETCDACC 2024

SECTION A [40 MARKS]


Answer ALL questions in this section
1. On the drawing paper provided, draw the border line, a title block and on it ,hand –print
the following;
i. Your name;
ii. Index number;
iii. Centre name;
iv. Paper name. [4 marks]
2. Hand- print in bold form and in capital each of the following;
i. Letters A to K;
ii. Numbers 0-9 [6 marks]
3. Draw an involute to a square of sides 20mm. [4 marks]
4. Make a free-hand sketches of the following tools and accessories;
om
i. Cartridge fuse
.c
et
tv

ii. Ball pein hammer


sy
ea

iii. Pliers [6 marks]


5. Fig. 1 shows a front elevation and a plan of a shaped block in first angle projection. Copy
the given views and draw the end elevation. [5 marks]

Page 2 of 6
© TVETCDACC 2024

6. Draw the Electrical symbols for the following electrical components:


i. Loud speaker
ii. Triode valve
iii. Lighting point [3 marks]
7. Construct a rectangle whose diagonal is 56mm and one side is 35mm. [5 marks]
8. State three properties that are modified by the dimension style manager. [3 marks]
9. Make a free hand sketch of a T-Square [2 marks]
10. Outline two rules as used in Technical drawing [2 marks]

om
.c
et
tv
sy
ea

Page 3 of 6
© TVETCDACC 2024

SECTION B [60 MARKS]


Answer any three questions in this section
11. Fig. 1 shows a model jet plane aerial view. Reproduce and print the figure as indicated
using computer aided drafting program (CAD). Attach the print out to your answer
booklet. [20 marks]

om
.c
et
tv
sy
ea

12. Fig 3 shows orthographic views of an object in third angle projection. Draw the full-scale
isometric view and insert all the dimension. (20 marks)
All fillets (4) = R14
All chamfers are 45o /15mm by 15mm

Page 4 of 6
© TVETCDACC 2024

Figure 3
13. Fig 4 shows a pictorial view of an object; om
.c
et
tv
sy
ea

Draw the following views in First angle projection;

Page 5 of 6
© TVETCDACC 2024

a) Front elevation in the direction of arrow A;


b) End elevation in the direction of arrow B
c) The plan p.

Insert any six major dimensions. [20 marks]

14. (a) Fig. 5 shows a wheel, 50mm diameter with a point on its periphery. If the wheel rolls
without slipping along a straight line while remaining in the same plane, plot the path of
P for one complete revolution of the wheel. [12 marks]

om
.c
et
tv
sy
ea

(b) Construct a common tangent to two circles of diameters 70mm and 50mm
respectively and centers 90mm apart. [8 marks]

THIS IS THE LAST PRINTED PAGE

Page 6 of 6

You might also like