Tangent Galvanometer

Moving Magnet Galvanometer (Pivoted Type)

Tangent galvanometer:

Principle: Based on the principle of tangents law in magnetism we need two uniform magnetic fields
at right angle to each other in which a magnetic needle is kept free to rotate. One of the two fields is
earth’s horizontal component of magnetic field along N‐S direction and the other magnetic field
along E‐W direction is produced by passingg the current n to be measured through u a circulara coil. A
o the needle the curre nt can be
compass box is keptt at the cen tre of the coil. From the deflection of
calculated.
e

A compass box mounted

u on the spindle is kept exactly ata the centree of the circular coil kept with its
plane vertical.
e A non conducting circular coils having different no of turns 50,100,200
0e & 500 all kept
mounted from one another. One n end of all the coils are connectedd to a common t terminal C at the
base while
h the other end of all are connected to four separate terminals. The vertical frame carrying
the coils can be rotated about a vertical axis passing through
o n
the centre. The instrument is supported
on levelling screws.

Theory: Since the direction of the magnetic field due to the current through the coil should be along
E‐W and magnetic field due to the circular coil carrying current is along its axis hence the plane of
the coil should be placed along N‐S direction.
 Tangent Galvanometer
Let n = no. of turns in the coil
A = the area of the plane of the coil
a = the mean radius of the circular
coil i = current flowing through the
coil
B H = the horizontal component along earths magnetic field
θ = the deflection of the compass needle
By applying tangent law :
F = B H tan θ → (1)

The magnetic field at the centre due to the circular coil carrying current is

μ 0 ni
F= → (2)
2 a
From equation (1) and equation (2)
μ 0 = B tan θ
H

ni
2 a
2 BH a
i= tan
θ μ 0n
Putting K μ 0n
= 2aB H
i = K tan θ → (3)

Thusby measuringthe angleof deflectionof the compassneedlethecurrentflowingthrough ht e

coil
can be calculated.
Thus we see that the proportional error is
Sensitivity : i = Ktanθ → (4) minimum when sin2θ is maximum
The proportional erroris definedas
di
i
Differentiating equation(4) we
2
get di = Ksec θdθ → (5) π
i.e. sin2 θ = 1 = sin
di Ksec2θdθ 2
∴ = π
i Ktanθ 2θ =
2
di dθ π
= θ =
i 2 sinθ 4
cos θ ×
cosθ
di
= 2dθ
i 2 sinθ cosθ
di 2dθ Thus the readingof a tangentgalvanometer
=
i sin 2θ 0
is most accurate when the reading is 45
 THE TANGENT GALVANOMETER

I. THEORY

The purpose of this experiment is to measure the horizontal and vertical components of
the earth's magnetic field. We will accomplish this by using a tangent galvanometer, an
instrument which preceded the modern ammeter. The tangent galvanometer was
originally designed to measure an unknown current by comparing the magnetic field
produced by that current with the earth's magnetic field. Using an ammeter together with
a tangent galvanometer, we can compute the earth's magnetic field.

The magnetic field at the center of a coil of N circular turns, each of radius R and
carrying a current I, has a magnitude
μ NI
Bc = 0
2R

in which μo is the permeability of free space.

Let such a coil be oriented in the vertical plane, with its central axis normal to the
horizontal component BEx of the earth's magnetic field BE. Refer to the diagram in
section IV. BE must then lie in the plane of the coil. When a current exists in the coil,
the resultant magnetic field at the center of the coil is the vector sum of Bc and BE.
r r r
B=Bc +BE
r
Since Bc lies entirely in the horizontal plane, the horizontal component of B is the vector
r r
sum of Bc and the horizontal component of Be .

r r r
B x =B c + B E x

r r
Let θ be the angle between B E and B . From the diagram, we see that

Bc = BEx tan θ
 We see from this equation that a graph of the magnetic field strength of the coils, Bc,
versus tan θ should yield a straight line with slope BEx. Also, the graph must go through
the origin, since θ is zero when Bc is zero. Because the graph must go through the origin,
the usual Least Squares equation for slope is not the most accurate one to use. We will
instead use the Modified Least Squares formula which gives the slope of the best fit line
constrained to pass through the origin.

In this experiment we will also measure the dip angle φ, defined as the angle between BE
and the horizontal plane. Then, having obtained the horizontal component of the earth's
field from the slope of the graph described above, and having measured the dip angle, we
can find the vertical component of the earth's field, and the magnitude of the field itself,
by simple trigonometry.

The tangent galvanometer consists of a horizontal test compass mounted at the center of a
vertical coil. The compass, in turn, consists of a non-magnetic pointer attached to a small
magnetized disk. With no current in the coil, the apparatus is oriented so that the
compass reads zero. The North and South poles of the magnetized disk will then lie in
the plane of the coil, with the North pole pointing toward BEx. After current is turned on,
the North pole will rotate through an angle θ and point toward Bx. The pointer, which
originally read zero, will now read θ.

II. LABORATORY PROCEDURE

CAUTION: Do not tilt the tangent galvanometer excessively, as the glass plate may fall out
and break.
1. Place the tangent galvanometer on an inverted wooden box to raise it above the ferrous
metal of the laboratory table. Remove all ferrous metal (such as certain mechanical
pencils) from the immediate vicinity of the tangent galvanometer. Turn the thumbscrew
to free the pointer, but do not raise the pointer so high that it pushes against the glass
plate. Orient the instrument so that the pointer reads zero. If the pointer is bent, each end
should be equally close to zero.
2. Place the circular level on top of the glass plate. Level the tangent galvanometer by
rotating one or more feet. Remove the level some distance from the instrument. If
necessary, rotate the box to re-zero the pointer.
3. Refer to the circuit diagram in section IV. Set the VOLTAGE and CURRENT control
knobs on the triple-output power supply to zero (full counter-clockwise position). Use a
banana plug lead to connect the positive terminal of the ammeter to the positive terminal
of the power supply (red banana jack). Connect the negative terminal of the ammeter
(0.1-A range) to a clip on the wiring board. Connect the 50 turn binding post of the
tangent galvanometer to the same wiring board clip. Connect the common binding post
of the tangent galvanometer (the post with no number next to it) to another clip of the
wiring board. Connect one fixed terminal of the 50 Ω resistor to the same clip. Use a
banana plug lead to connect the other fixed terminal of the 50 Ω resistor to the negative
terminal of the power supply (black banana jack). Set the ammeter (with its internal
magnet) some distance from the tangent galvanometer.
4. Turn the power supply on and rotate the CURRENT control knob to its far counter-
clockwise position. While observing the ammeter, adjust the VOLTAGE control knob
 o
until that the tangent galvanometer reads 20 . If the ammeter reading fluctuates
o o
noticeably, tighten all connections. Record the current. Repeat for angles of 30 , 40 and
o
50 . Change the ammeter range, if necessary, to keep it on scale.
5. Reverse the direction of the current through the coil (NOT THROUGH THE
AMMETER) and repeat.
6. Change to the 5 turn binding post of the tangent galvanometer and the 1-A range of the
ammeter. Replace the 50 Ω resistor by the 5 Ω resistor. Repeat steps 4 and 5.
7. Lock the pointer, but do not move the tangent galvanometer.
8. The dip compass reads correctly only if its (horizontal) axis of rotation is perpendicular to
the horizontal component of the earth's magnetic field. To accomplish this, sight parallel
to the coil of the tangent galvanometer at a fixed object on the other side of the room.
Remove the tangent galvanometer from the box and replace it by the dip compass. Align
the dip compass so that its protractor is parallel to the plane previously occupied by the
coil, using your sighted reference point. Move the tangent galvanometer some distance
away so that its magnetized disk does not affect the dip compass. Record the dip angle
between the horizontal plane and the earth's magnetic field.
9. Use outside calipers and a meter stick to measure the outside diameter of the coil.
Measure the actual windings, not the metal frame.
10. Measuring the inside diameter of the windings is a bit more difficult, because the
compass is in the way. Also, we must compensate for the thickness of the metal frame.
Measure and record the thickness of the metal which makes up the frame. Using the
calipers as outside calipers, open them until they span the inside diameter of the metal
frame. Place them on the meter stick; read and record the distance. Finally, add two
metal thicknesses to the distance, to obtain the inside diameter of the windings.

III. CALCULATIONS

1. Calculate the average coil radius.

2. Average each pair of currents, measured for the same number of turns and for the same
angle of the pointer. Make a table containing the quantities: number of turns, angle,
current, and magnetic field strength of the coils (in μT). Show the calculation of the
magnetic field strength in one case.
3. Average the two values of the magnetic field strength of the coils for each angle. List the
results in a table containing the quantities angle, tan θ, and magnetic field strength of the
coils.
4. Plot a graph of magnetic field strength versus tan θ. Use a straightedge to draw the line
that best-fits the data points and passes through the origin.
5. Use the Modified Least Squares formula to calculate the slope of your graph. The
formula can be found in the Introduction of this Lab Manual.
6. What is the horizontal component, BEx, of the earth's magnetic field, in μT, at the location
of the apparatus?
7. What is the vertical component of the earth's field at the same location?
8. What is the magnitude of the earth's resultant magnetic field at the same location?
IV. DIAGRAMS

Front
View

Top
View

Circu
it