Bulletin No.

: 23-NA-046
Service Bulletin Date: April, 2023

TECHNICAL
Subject: Power Windows and/or Mirrors Inoperative, Power Seat Movement Inoperative and/or
Moving On Its Own, Side Object Detection Inoperative and/or Unwanted Activation,
Power Door Lock Cycle Inoperative, Keyless Entry Inoperative - DTC B3125, B3130
and/or B3135 Set

This bulletin replaces PIT5608E. Please discard PIT5608E.

Model Year: VIN:

Brand: Model: Engine: Transmission:
from to from to
Chevrolet Equinox
2023
GMC Terrain 2018
Holden Equinox 2020

North America, Middle East, Israel, Palestine, Argentina (Mercosur), Brazil (Mercosur),
Involved Region or Country
GM Korea Company, Thailand (ASEAN), Australia/New Zealand, Egypt
Some customers may comment that:
• Power door locks inoperative
• Keyless entry inoperative
• Power windows and power mirror inoperative
• Power seats inoperative and/or moving on its own
Condition • Side object detection inoperative and/or unwanted activation
Some technicians may find one or more of the following DTCs set in the Body Control
Module (BCM):
• B3125
• B3130
• B3135
This condition may be caused by one or more of the following:
• Damage or displaced foam connector seal.
Cause
• Water leaking past the body plug(s) located in the “A” hinge pillar above door harness
to body connectors X500 and/or X600 causing corrosion in the connector.

Copyright 2023 General Motors LLC. All Rights Reserved.

Page 2 April, 2023 Bulletin No.: 23-NA-046

Check the condition of the following connectors and the mating body harness for signs of
water intrusion. Refer to Inline Harness Connector End Views in SI.
• X500 Front Side Door, Door Wiring Harness - Driver to Body Wiring Harness
• X600 Front Side Door, Door Wiring Harness - Passenger to Body Wiring Harness
• X700 Rear Side Door, Door Wiring Harness - Left Rear to Body Wiring Harness
• X800 Rear Side Door, Door Wiring Harness - Right Rear to Body Wiring Harness

Correction

6298254

There are adhesive-backed foam seals at the X500/X600 connector locations on the
lower “A” hinge pillars.
– If the foam seal (1) is distorted, damaged or missing, replace the seal.

Important: Service agents must comply with all

International, Federal, State, Provincial, and/or
Local laws applicable to the activities it performs
under this bulletin, including but not limited to
handling, deploying, preparing, classifying,
packaging, marking, labeling, and shipping
dangerous goods. In the event of a conflict between
the procedures set forth in this bulletin and the
laws that apply to your dealership, you must follow
those applicable laws.

Service Procedure
Check the terminals on both sides of connector for
signs of corrosion.
⇒ For repairing the wiring. Refer to Wire to Wire
Repair in SI.

6298256

Evaluate the body plug(s) located in the “A” hinge pillar

above door harness to body connectors X500 and/or
X600, are seated and sealing properly.
Bulletin No.: 23-NA-046 April, 2023 Page 3

Parts Information
Causal Description Part Qty
Part Number
X SEAL-FRT S/D
DR WRG HARN 23487135 As Required
HOLE OPG
X PLUG, BODY H/
PLR OTR PNL
25883487 As Required
HOLE
(DIA 31MM)

Warranty Information
For vehicles repaired under the Bumper-to-Bumper
coverage (Canada Base Warranty coverage), use the
following labor operation. Reference the Applicable
Warranties section of Investigate Vehicle History (IVH)
for coverage information.

Labor Operation Description Labor Time

2086118* Inspect Door Pass-Through Connectors for Water Intrusion 0.5 hr
Add Replace SEAL-FRT S/D DR WRG HARN HOLE OPG 0.2 hr
Add Replacing Body Side Outer Panel Plugs 0.2 hr
Use the Published Labor
5430902 Wire-to-Wire Repair
Operations Time
*This is a unique Labor Operation for Bulletin use only.

Version 1
Modified Released April 17, 2023

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these
technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper WE SUPPORT VOLUNTARY
service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a
job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your TECHNICIAN
vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the CERTIFICATION
information.