Digimatic Indicators

ABSOLUTE Digimatic Indicator ID-C

SERIES 543 — Peak-Value Hold Type

Functions • Run-out /MAX-MIN Hold function enables • By using the parameter setup kit (optional)
• Peak detection (MAX/MIN) GO/NG judgment*1 for peak or difference
• Runout (MAX - MIN) Hold and the dedicated software, the functions
Note: P eak detection values. and the parameters can be configured using
1) Sampling rate: 50 readings/s • Five buttons, status icons, and clear button a computer.
2) Capturing speed: 50 µm/s (max.)
• Zeroset (INC system) indications allow for easy operation of a wide • Equipped with a data output port that enables
• Preset function (ABS system) variety of functions. incorporation into measurement networking
• Measuring direction switching • Wide LCD and new analog bar graph are and statistical process control systems. (Refer
• Tolerance judgment
(3 pairs of ABS, INC memory function) now standard on all models. to page A-3)
• Resolution selection • The ABS (absolute) scale restores the last *1 Tolerance judgment results cannot be output.
• Simple calculation f(x) =Ax origin position*2 automatically when the *2 Refer to “Origin Setting of Digimatic Indicators” on page
• Analog bar resolution selection F-25.
• Key lock indicator is turned on, and realizes high
• in/mm conversion (inch/mm type) reliability by eliminating over-speed errors.
• Display hold (when no external device is connected)
• Data output
• External PC setting input
• Display rotation (330°)
• Low battery voltage alarm display
• Error alarm display
Optional Accessories
• Lifting
Lifting lever 21EZA198
Lifting knob 21EZA105
• SPC Cable:
905338 (1 m)
9 05409 (2 m)
• USB Input Tool Direct (2 m) : 06AFM380F
• Input Tool Series
IT-020U (USB Keyboard Signal Conversion Type):
264-020
IT-007R (RS-232C Communication Conversion Type):
264-007
• Connecting Cables for U-WAVE-T (160 mm):
02AZD790F
For foot switch: 02AZE140F
• Digimatic Mini-Processor DP-1VA LOGGER: 264-505
• Parameter setup kit: 21EZA313
Note: P arameter setting software (can be downloaded
for free from the Mitutoyo website) is also required.

543-300-10/543-300B-10

Parameter setup kit SPECIFICATIONS

Metric ISO/ JIS type ASME/ ANSI / AGD type
Parameter setting software Maximum permissible error (mm) Measuring
Order No. Range Resolution Battery life Net mass
(w / lug, flat back) (mm) (mm) Hysteresis Repeatability force Power supply (normal use)*2 (g)
MPEE*1 MPL (N)
MPEH MPER
543-300-10 0.001 / 180
12.7 0.01 0.003 0.002 0.002 1.5 or less CR2032×1 pc. Approx. 1 year
543-300B-10*3 (selectable) 170

Inch / Metric
Maximum permissible error Measuring
Order No. Battery life Net mass
Range Resolution Hysteresis Repeatability force Power supply (normal use)*2 (g)
(w / lug, flat back) MPEE*1
MPEH MPER MPL (N)
543-301-10 0.00005 / 180
543-301B-10*3 0.5 in / 0.0001 / 170
±0.00010 in 0.00010 in 0.00010 in
0.0005 in, 1.5 or less CR2032×1 pc. Approx. 1 year
543-302-10 12.7 mm
0.001 / 0.01 mm
/0.003 mm / 0.002 mm / 0.002 mm 195 F
543-302B-10*3 (selectable) 170
*1 Error of indication for the total measuring range
*2 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only.
*3 Flat back

Mitutoyo reserves the right to change any or all aspects of any product specification, including prices, designs and service content, without notice. F-10
 Digimatic Indicators

DIMENSIONS

ISO/JIS ø10.9 28.6 20 Unit: mm

Type
50.1

ø54
ø59.4

ø6.
5
46.5
54.4

0
ø8-0.009
16.8

ø4.8 Ball contact (ø3)

901312
(threaded: M2.5×0.45)
21.2
13.3

7.3

7.6

ø 0.43
ASME/ANSI/AGD 1.13 3/4 Unit: in
Type
1.97

1/4
ø 2.13
ø 2.34

ø1
/4
1.74
2.00

0.59

0
ø0.375 -0.0012
ø 0.19
Ball contact (ø 0.12)
0.79
0.52

21BZB005
(thread: No. 4-48UNF)
0.30
1/4

F-11 Mitutoyo reserves the right to change any or all aspects of any product specification, including prices, designs and service content, without notice.