TO INDEX

J1 LIGHTING

LIGHTING ---------------------------------------- J1 - 1 ROOM LAMP BULB-------------------------- J1 - 22

INSTRUCTIONS FOR SERVICE REMOVAL AND INSTALLATION ------ J1 - 22
OPERATION ---------------------------------- J1 - 1 ROOM LAMP BULB
ARTICLES TO BE PREPARED ---------- J1 - 1 (LUGGAGE ROOM LAMP)----------------- J1 - 23
BASIC CHECK AND ADJUSTMENT --- J1 - 1 REMOVAL AND INSTALLATION ------ J1 - 23 J1
FUNCTION CHECK------------------------- J1 - 5 HEADLAMP DIMMER SWITCH AY------ J1 - 24
UNIT CHECK --------------------------------- J1 - 5 REMOVAL AND INSTALLATION ------ J1 - 24
HEADLAMP AY --------------------------------- J1 - 8
REMOVAL AND INSTALLATION -------- J1 - 8
FRONT FOG LAMP AY ----------------------- J1 - 9
REMOVAL AND INSTALLATION -------- J1 - 9
SIDE TURN SIGNAL LAMP AY ----------- J1 - 11
REMOVAL AND INSTALLATION------- J1 - 11
REAR COMBINATION LAMP AY --------- J1 - 12
REMOVAL AND INSTALLATION ------ J1 - 12
HIGH MOUNTED STOP LAMP AY ------ J1 - 13
REMOVAL AND INSTALLATION ------ J1 - 13
LICENSE PLATE LAMP AY ---------------- J1 - 14
REMOVAL AND INSTALLATION ------ J1 - 14
ROOM LAMP AY
(FRONT MAP LAMP) ------------------------ J1 - 15
REMOVAL AND INSTALLATION ------ J1 - 15
ROOM LAMP AY------------------------------ J1 - 16
REMOVAL AND INSTALLATION ------ J1 - 16
ROOM LAMP AY
(LUGGAGE ROOM LAMP)----------------- J1 - 17
REMOVAL AND INSTALLATION ------ J1 - 17
HEADLAMP BULB---------------------------- J1 - 18
REMOVAL AND INSTALLATION ------ J1 - 18
CLEARANCE LAMP BULB----------------- J1 - 19
REMOVAL AND INSTALLATION ------ J1 - 19
FRONT TURN SIGNAL LAMP BULB --- J1 - 20
REMOVAL AND INSTALLATION ------ J1 - 20
FRONT FOG LAMP BULB ----------------- J1 - 21
REMOVAL AND INSTALLATION ------ J1 - 21
SIDE TURN SIGNAL LAMP BULB------- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
TAIL AND STOP LAMP BULB------------- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
REAR TURN SIGNAL LAMP BULB ----- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
BACK UP LAMP BULB---------------------- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
REAR FOG LAMP BULB ------------------- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
HIGH MOUNTED STOP LAMP BULB -- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
LICENSE PLATE LAMP BULB ------------ J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
ROOM LAMP BULB
(FRONT MAP LAMP BULB) --------------- J1 - 22
REMOVAL AND INSTALLATION ------ J1 - 22
J1–1
1 LIGHTING
1-1 INSTRUCTIONS FOR SERVICE OPERATION
1-1-1 ITEMS TO BE OBSERVED DURING REPLACEMENT OF EACH LAMP
1.Halogen lamps become very high temperature while they are operated. When grease etc gets to the
bulb surface, the bulb life will be shortened. Therefore, hold the flange section during the replacement.
Do not allow your hand to touch the glass section.
2.If your hand should touch the bulb, degrease the affected section using alcohol etc. and proceed to
assemble it to the lamp.
3.In the case of halogen lamps, the pressure inside the glass bulb is very high. Hence, if the bulb is
dropped or hit or scratched, it is prone to be broken and the glass be scattered around.
4.If the bulb is left in a detached state for a prolonged period of time, there are possibilities that dirt or
humidity gets to the lens. Therefore, when the bulb is to be replaced, first prepare a new bulb and then
start to replace it.
5.The bulb should be replaced by a bulb with the same wattage.
6.Improper installation of the socket will cause the lens to be misted or allow water to be admitted. After
completion of the bulb replacement, make sure to install the socket correctly.
1-2 ARTICLES TO BE PREPARED
Instrument
Electrical Tester

1-3 BASIC CHECK AND ADJUSTMENT

1-3-1 HEADLAMP PHOTOMETRIC AXIS ADJUSTMENT
(1) Operation prior to photometric axis adjustment
1.Adjust the tire air inflation pressure to the specified value.
2.Seat one person at the Driver's seat.
3.Replenish oils to the specified levels. Fill gasoline to the full capacity.
4.Mount the tools, jack and spare tire at the specified positions.
5.Rock the vehicle in the up-and-down direction as well as in the right-and-left direction so that the sus-
pension may bed well.
6.Set the engine speed to a level of 1500 rpm or more. (If the engine speed is too low, the lamp termi-
nal voltage drops, thus making it difficult to recognize the cut-off line.
NOTE
• Cut-off line: Boundary line between the bright zone and dark zone in the low beam.

7.In the case of motor vehicles equipped with a headlamp levelling switch, set the levelling switch to the
zero position.
 J1–2
(2) Photometric axis adjustment
1.Adjust the photometric axis of the low beam according to
For right-and-left direction adjustment
the instruction manual of the headlamp tester to be used.

Inside
vehicle

For up-and-down direction adjustment

T11H5001ET16

Reference range of cut-off line elbow points

Range from 1.0% to 1.5% below the horizontal line that passes through the lamp center (Ref-
Vertical position
erence position: 1.2% below)
Range between 1.7 % right and left from the vertical line that passes through the lamp center:
Horizontal position
(Reference position: On the vertical line that passes through the lamp center)

1.7 1.7

Center of the headlamp

Cut off line

(Reference position)
1.0
1.2 Elbow point
1.5

:Reference range of Elbow points

C13H5001S16

Unit : %
NOTE
• Elbow point: Point where the cut-off line is articulated

1-3-2 FRONT FOG LAMP PHOTOMETRIC AXIS ADJUSTMENT

(1) Operation prior to photometric axis adjustment
1.Turn over the shield S/A, fender splash, front RH/LH to such an extent that the photometric axis adjust-
ment can be done.
Refer to Page I1-24.

2.Adjust the tire air inflation pressure to the specified value.

3.Set the engine speed to a level of 1500 rpm or more.
J1–3
(2) Photometric axis adjustment
1.Prepare a screen for the adjustment use as indicated in the figure.

H11H5009S16

2.Place the screen normally at a distance of three meters ahead of the lamp. Align line H with the cen-
ter of the front fog lamp.
• This normal placing can be carried out easily when a screen is affixed to the lens of the headlamp
tester.

3.Turn ON the front fog lamp. Perform adjustment in such a

way that the light distribution comes in the shaded section
on the screen.
NOTE
• Perform the adjustment by turning the aiming screw in UP
the tightened direction. (When performing the adjust-
ment in the loosening direction, first loosen the screw,
then turn it in the tightened direction.)
• There is no screw for the right-and-left direction adjust-
ment. For up-and-down
• The figure shows the right side front fog lamp. direction adjustment

T11H5502ET16
 J1–4
1-3-3 MANUAL HEADLAMP LEVELING OPERETION CHECK
1.Perform the photometric axis adjustment for the headlamp.
Refer to Page J1-1.

2.Place the screen normally at a distance of three meters ahead of the lamp.
NOTE
• This normal placing can be carried out easily when a screen is affixed to the lens of the headlamp
tester.

3.Turn the headlamp leveling switch 0-1-2-3-4-5. At this time, check the vertical movement amount on
the photometric axis.
Headlamp leveling switch
Position Movement amount (mm)
0(1 30
1(2 30
2(3 30
3(4 30
4(5 30

1-3-4 OPERATION CHECK OF LIGHTING DEVICES

1.Visually check the operation of lamps, etc. provided on the vehicle surface.
(1) Headlamp(Hi-Lo change)
(2) Clearance lamp
(3) Tail lamp
(4) Stop lamp
(5) Back-up lamp
(6) License plate lamp
(7) Turn signal lamp
(8) Hazard lamp
(9) Fog lamp
SPECIFIED VALUE: Illuminates or flashes normally.

2.Visually check the operation of the room lamp.

SPECIFIED VALUE: Illuminates normally.

1-3-5 CHECK OF LIGHTING DEVICE FOR INSTALLING CONDITION

1.Shake the lamps, etc. by hand and check the installing condition.
SPECIFIED VALUE: There should be no excessive play.

2.Check that the lens or reflector of the lamp has no damage such as discoloration and crack. Also
check that they are not smeared and that no water has been admitted in the lamp.
SPECIFIED VALUE: There should be no discoloration nor cracks.
SPECIFIED VALUE: There should be no contamination nor admission of water.
J1–5
1-4 FUNCTION CHECK
1-4-1 HEADLAMP LEVELING SWITCH
(1) Voltage test
1.With the connector connected, operate the headlamp lev-
2 1
eling switch. At this time, working from the back of the
connector, check the voltage between the connector ter- 6 5 4 3
minals using an electrical tester.
Specified value
Voltage T11H5504T10
Switch
Terminal No. (At time of battery
position
voltage of 12 V)
0 4(LH) and 5(RH) ( 2(GND) 10.4 ( 11.2V
1 4(LH) and 5(RH) ( 2(GND) 9.2 ( 9.9V
2 4(LH) and 5(RH) ( 2(GND) 7.9 ( 8.6V
3 4(LH) and 5(RH) ( 2(GND) 6.6 ( 7.3V
4 4(LH) and 5(RH) ( 2(GND) 5.3 ( 6.0V
5 4(LH) and 5(RH) ( 2(GND) 4.0 ( 4.8V

1-5 UNIT CHECK

1-5-1 HEADLAMP DIMMER SWITCH(VEHICLE WHERE IT
IS INSTALLED AT THE RIGHT SIDE THE COLUMN)
1.Check continuity between terminals in each state. 4 3 2 1
Light control switch 13 12 11 10 9 8 7 6 5
Switch condition Terminal No. Standard
TAIL 5(8 Continuity exists.
HEAD 5 ( 8, 6 ( 7 Continuity exists.
M21H6006T10
Headlamp dimmer switch
Switch condition Terminal No. Standard
FLASH 6(7(9 Continuity exists.
LOW BEAM 7 ( 10 Continuity exists.
HIGH BEAM 7(9 Continuity exists.

Turn signal switch

Switch condition Terminal No. Standard
RIGHT 12 ( 13 Continuity exists.
LEFT 11 ( 12 Continuity exists.

Front fog lamp switch

Switch condition Terminal No. Standard
ON 1(3 Continuity exists.
 J1–6
1-5-2 HEADLAMP DIMMER SWITCH(VEHICLE WHERE IT
IS INSTALLED AT THE LEFT SIDE OF THE CUL-
UMN)
1.Check continuity between terminals in each state.
4 3 2 1
Light control switch
Switch condition Terminal No. Standard
13 12 11 10 9 8 7 6 5
TAIL 10 ( 13 Continuity exists.
HEAD 10 ( 13, 11 ( 12 Continuity exists.

Headlamp dimmer switch M21H6006T10

Switch condition Terminal No. Standard
FLASH 9 ( 11 ( 12 Continuity exists.
LOW BEAM 8 ( 11 Continuity exists.
HIGH BEAM 9 ( 11 Continuity exists.

Turn signal switch

Switch condition Terminal No. Standard
RIGHT 6(7 Continuity exists.
LEFT 5(6 Continuity exists.

Front fog lamp switch

Switch condition Terminal No. Standard
ON 2(4 Continuity exists.

Rear fog lamp switch

Switch condition Terminal No. Standard
ON 3(4 Continuity exists.

Front fog lamp switch ' Rear fog lamp switch

Switch condition Terminal No. Standard
ON(Front fog lamp) 2(4 Continuity exists.
OFF(Front fog lamp
switch ' Rear fog 2 ( 3( 4 Continuity exists.
lamp switch)

1-5-3 HAZARD SWITCH(HEATER CONTROL AY )

1.Check continuity between terminals when the hazard
switch is turned ON.
Switch condition Terminal No. Standard
ON 2(3 Continuity exists. 10 9 8 7 6 5 4 3 2 1

T11H5002T10

1-5-4 COURTESY SWITCH

1.Check the continuity between the switch connector termi-
nal and the switch body.
Switch condition Standard
When free Continuity exists.
When pushed No continuity exists.

C11H5027T10
J1–7
1-5-5 STOP LAMP SWITCH
1.Check continuity between the switch connector terminals.
Switch condition Standard
When free Continuity exists.
When pushed No continuity exists. 2 1

M21C7079T10

1-5-6 HEADLAMP RELAY

1.Check continuity between the respective terminals of the
connector.
1
Terminal No. Standard 4 1

1(4 No continuity exists. 3 2

2(3 Continuity exists. 2 3
4

2.Apply the battery voltage between the terminals 2 and 3.

T11H5004T10
At this time, check continuity between the terminals 1 and
4.
SPECIFIED VALUE: Continuity exists.
1-5-7 FOG LAMP RELAY
1.Check continuity between the respective terminals of the
connector. 4 2
4
Terminal No. Standard 2
2(4 No continuity exists.
1 3
1(3 Continuity exists. 3 1

2.Apply the battery voltage between the terminals 1 and 3.

M21H5081T10
At this time, check continuity between the terminals 2 and
4.
SPECIFIED VALUE: Continuity exists.
 J1–8
2 HEADLAMP AY
2-1 REMOVAL AND INSTALLATION
2-1-1 OPERATION BEFORE REMOVAL
1.Remove the front bumper cover.
Refer to Page I2-2.

2-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

S
a

T11H5501S16

(2) Removal and installation procedures

1 a Headlamp Ay, RH/LH

2-1-3 OPERATION AFTER INSTALLATION

1.Install the front bumper cover.
Refer to Page I2-2.

2.Perform the photometric axis adjustment for the headlamp.

Refer to Page J1-1.
J1–9
3 FRONT FOG LAMP AY
3-1 REMOVAL AND INSTALLATION
3-1-1 OPERATION BEFORE REMOVAL
1.Remove the front bumper cover.
Refer to Page I2-4.

3-1-2 REMOVAL AND INSTALLATION PROCEDURES

3-1-3 ARTICLES TO BE PREPARED
Lubricant,adhesive,others
Protective tape

(1) Components

T11H5503S16

(2) Removal and installation procedures

j 1 a Lamp Ay,fog (RH/LH)

3-1-4 POINTS OF REMOVAL Housing boss

(1) Lamp Ay, fog, RH/LH

1.Perform operations from the back of the bumper.
2.Hold the claw of the aiming gear grommet.
3.Disengage the housing boss at the both sides of the lamp
Ay from the bumper and push out the lamp Ay.

Aiming gear grommet

T11H5507ET16
 J1–10
3-1-5 OPERATION AFTER INSTALLATION
1.Install the front bumper cover.
Refer to Page I2-4.

2.Perform the photometric axis adjustment for the front fog lamp.
Refer to Page J1-2.
J1–11
4 SIDE TURN SIGNAL LAMP AY
4-1 REMOVAL AND INSTALLATION
4-1-1 REMOVAL AND INSTALLATION PROCEDURES
(1) Components

T11H5006S16

(2) Removal and installation procedures

j 1 a Lamp Ay, side turn signal(RH/LH)
2 b Socket
3 c Bulb

4-1-2 POINTS OF REMOVAL

(1) Lamp Ay, side turn signal, RH/LH
1.Removes the lamp Ay by pushing it toward the rear of the
vehicle.

Front

T11H5020T16
 J1–12
5 REAR COMBINATION LAMP AY
5-1 REMOVAL AND INSTALLATION
5-1-1 OPERATION BEFORE REMOVAL
1.Remove the rear deck trim cover.
Refer to Page I2-48.

2.Remove the rear RH/LH quarter trim panel Ay.

Refer to Page I2-48.

5-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

B
b

f
c

d
e

T11H5007S16

(2) Removal and installation procedures

j 1 a Lamp Ay, rear combination, RH/LH 6 f Harness Ay
2 b Bulb ( Tail & stop lamp)
3 c Bulb ( Rear turn signal lamp)
4 d Bulb ( Back up lamp)
5 e Bulb ( Rear fog lamp)

5-1-3 POINTS OF REMOVAL

(1) Lamp Ay, rear combination, RH/LH
1.Remove the two(2) mounting bolts, and then release the
stud pin from the grommet (two locations) to disassemble
the lamp Ay.

T11H5028T10

5-1-4 OPERATION AFTER INSTALLATION

1.Remove the rear RH/LH quarter trim panel Ay.
Refer to Page I2-48.

2.Install the rear deck trim cover.

Refer to Page I2-48.
J1–13
6 HIGH MOUNTED STOP LAMP AY
6-1 REMOVAL AND INSTALLATION
6-1-1 REMOVAL AND INSTALLATION PROCEDURES
(1) Components

S
S

T11H5008S16

(2) Removal and installation procedures

j 1 a Cover, center stop lamp
2 b Lamp Ay, stop center
3 c Socket
4 d Bulb

6-1-2 POINTS OF REMOVAL

(1) Cover, center stop lamp
1.Slide the cover toward the rear of the lamp Ay to release
and remove from the lamp Ay.

T11H5021T16
 J1–14
7 LICENSE PLATE LAMP AY
7-1 REMOVAL AND INSTALLATION
7-1-1 REMOVAL AND INSTALLATION PROCEDURES
(1) Components
b

c
a

T11H5016S16

(2) Removal and installation procedures

j 1 a Lamp Ay, license plate
2 b Socket
3 c Bulb
4 d Lens, license plate lamp

7-1-2 POINTS OF REMOVAL

(1) Lamp Ay, license plate
1.Remove the lamp Ay, while pressing down the deflecting Pawl section Deflection section
portion.

T11H5023ET10
J1–15
8 ROOM LAMP AY
8-1 REMOVAL AND INSTALLATION
8-1-1 ARTICLES TO BE PREPARED
Lubricant,adhesive,others
Protective tape

8-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

b
b

c
c

T11H5010S20

(2) Removal and installation procedures

j 1 a Lamp Ay, map
2 b Socket
3 c Bulb

8-1-3 POINTS OF REMOVAL

(1) Lamp Ay, map
1.Remove by disengaging the pawls (at four points), using a
flat screwdriver wrapped with a protective tape.

:Pawl position

T11H5024ET10
 J1–16
9 ROOM LAMP AY
9-1 REMOVAL AND INSTALLATION
9-1-1 REMOVAL AND INSTALLATION PROCEDURES
(1) Components

S
a c
S

H11H5022S16

(2) Removal and installation procedures

1 b Lens, dome lamp
2 c Bulb
3 a Lamp Ay, dome
J1–17
10 ROOM LAMP AY
10-1 REMOVAL AND INSTALLATION
10-1-1 ARTICLES TO BE PREPARED
Lubricant,adhesive,others
Protective tape

10-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

b
a

T11H5011S16

(2) Removal and installation procedures

j 1 a Lamp Ay, dome
2 b Bulb

10-1-3 POINTS OF REMOVAL

(1) Lamp Ay, dome
1.Using a flat (() screw driver wound with a protective tape,
release.

Front

T11H5025ET10
 J1–18
11 HEADLAMP BULB
11-1 REMOVAL AND INSTALLATION
11-1-1 REMOVAL AND INSTALLATION PROCEDURES
(1) Components

T11H5012S16

(2) Removal and installation procedures

1 a Cover, headlamp
2 b Bulb(Headlamp)
J1–19
12 CLEARANCE LAMP BULB
12-1 REMOVAL AND INSTALLATION
12-1-1 OPERATION BEFORE REMOVAL
1.Turn over the RH/LH front fender liner (front RH/LH fender splash shield S/A in the case of the aero
specification vehicles) to provide a space to remove the bulb.
NOTE
• For easier operation, the steering wheel may be kept
in a turned state during this operation, thus providing
extra work space.
Refer to Page I1-24.

T11H5026T16

12-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components
a

T11H5014S16

(2) Removal and installation procedures

1 a Socket ( Clearance lamp)
2 b Bulb ( Clearance lamp)

12-1-3 OPERATION AFTER INSTALLATION

1.Return the RH/LH front fender liner (front RH/LH fender splash shield S/A in the case of the aero spec-
ification vehicles) to the original state.
Refer to Page I1-24.
 J1–20
13 FRONT TURN SIGNAL LAMP BULB
13-1 REMOVAL AND INSTALLATION
13-1-1 OPERATION BEFORE REMOVAL
1.Turn over the LH front fender liner (front LH fender splash shield S/A in the case of the aero specifica-
tion vehicles) to provide a space to disengage the socket. (When replacing the LH side bulb)
Refer to Page I1-24.

NOTE
• The RH bulb can be replaced from the engine com-
partment.
• For easier operation, the steering wheel may be kept
in a turned state during this operation, thus providing
extra work space.

13-1-2 REMOVAL AND INSTALLATION PROCEDURES T11H5026T16

(1) Components

T11H5015S16

(2) Removal and installation procedures

1 a Socket ( Front turn signal lamp)
2 b Bulb ( Front turn signal lamp)

13-1-3 OPERATION AFTER INSTALLATION

1.Return the LH front fender liner (front LH fender splash shield S/A in the case of the aero specification
vehicles) to the original state.(When replacing the LH side bulb)
Refer to Page I1-24.
J1–21
14 FRONT FOG LAMP BULB
14-1 REMOVAL AND INSTALLATION
14-1-1 OPERATION BEFORE REMOVAL
1.Turn over the front RH/LH fender splash shield S/A to pro-
vide a space to remove the bulb.
NOTE
• The space for the work can be easily obtained if the
operation is performed with the steering wheel held in
a turned state.
Refer to Page I1-24.

B11H5010T16

14-1-2 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

T11H5505S16

(2) Removal and installation procedures

1 a Bulb( Front fog lamp)

14-1-3 OPERATION AFTER INSTALLATION

1.Return the front RH/LH fender splash shield S/A to the original state.
Refer to Page I1-24.

2.Perform the photometric axis adjustment for the front fog lamp.
 J1–22
15 SIDE TURN SIGNAL LAMP BULB
15-1 REMOVAL AND INSTALLATION
Refer to Page J1-11.

16 TAIL AND STOP LAMP BULB

16-1 REMOVAL AND INSTALLATION
Refer to Page J1-12.

17 REAR TURN SIGNAL LAMP BULB

17-1 REMOVAL AND INSTALLATION
Refer to Page J1-12.

18 BACK UP LAMP BULB

18-1 REMOVAL AND INSTALLATION
Refer to Page J1-12.

19 REAR FOG LAMP BULB

19-1 REMOVAL AND INSTALLATION
Refer to Page J1-12.

20 HIGH MOUNTED STOP LAMP BULB

20-1 REMOVAL AND INSTALLATION
Refer to Page J1-13.

21 LICENSE PLATE LAMP BULB

21-1 REMOVAL AND INSTALLATION
Refer to Page J1-14.

22 ROOM LAMP BULB(FRONT MAP LAMP BULB)

22-1 REMOVAL AND INSTALLATION
To replace the bulb, remove the map lamp Ay, and then remove the bulb from the back side of the lamp
Ay.
CAUTION
• It is important to remove the bulb from the backside of the lamp Ay, to prevent damage to the
switch that may occur if the lens is removed.

Refer to Page J1-15.

23 ROOM LAMP BULB

23-1 REMOVAL AND INSTALLATION
Refer to Page J1-16.
J1–23
24 ROOM LAMP BULB(LUGGAGE ROOM LAMP BULB)
24-1 REMOVAL AND INSTALLATION
Refer to Page J1-17.
 J1–24
25 HEADLAMP DIMMER SWITCH AY
25-1 REMOVAL AND INSTALLATION
25-1-1 ARTICLES TO BE PREPARED
Lubricant,adhesive,others
Protective tape

25-1-2 OPERATION BEFORE REMOVAL

1.Remove the lower steering column cover.
Refer to Page G1-5.

2.Remove the upper steering column cover.

Refer to Page G1-5.

25-1-3 REMOVAL AND INSTALLATION PROCEDURES

(1) Components

L21H6065S20

(2) Removal and installation procedures

j 1 a Switch Ay, headlamp dimmer

25-1-4 POINTS OF REMOVAL

(1) Switch Ay, headlamp dimmer
1.Using a flat (() screwdriver wound with a protective tape, release the fitting of the the claw.
25-1-5 OPERATION AFTER INSTALLATION
1.Install the upper steering column cover.
Refer to Page G1-5.

2.Install the lower steering column cover.

Refer to Page G1-5.

TO INDEX TO NEXT SECTION