SAFETY PRECAUTIONS

5345
Technical Service Data
SERVICE WARNING SAFETY CHECKS — FIRE AND SHOCK HAZARD
Only qualified service technicians who are familiar with safety checks Cold Leakage Checks for Receivers with Isolated Ground
AKAI

SET 5345
Model CFT27918X (Chassis KS3A)
and guidelines should perform service work. Before replacing parts,
disconnect power source to protect electrostatically sensitive parts. Do Unplug the AC cord, connect a jumper across the plug prongs, and turn
not attempt to modify any circuit unless so recommended by the the power switch on (if applicable). Use an ohmmeter to measure the
INDEX
manufacturer. When servicing the receiver, use an isolation transformer resistance between the jumped AC plug and any exposed metal cabinet
between the line cord and power receptacle. parts such as antenna screw heads, control shafts, or handle brackets.

SERVICING THE HIGH VOLTAGE AND CRT

Exposed metal parts with a return path should measure between 1M High Voltage Shutdown Test ................... 1
ohms and 5.2M ohms. Parts without a return path must measure infinity. Important Parts Information .................... 4
Hot Leakage Current Check
Use EXTREME CAUTION when servicing the high voltage circuits. To Miscellaneous Adjustments .................... 1
discharge static high voltage, connect a 10K ohms resistor in series with a Parts List .................................................. 4
test lead between the receiver ground and CRT anode lead. DO NOT lift Plug the AC cord directly into an AC outlet. DO NOT use an isolation
transformer. Use a 1500 ohms, 10W resistor in parallel with a .15µF
Placement Chart ...................................... 1
the CRT by the neck. Always wear shatterproof goggles when handling
the CRT to protect eyes in case of implosion. capacitor to connect between any exposed metal parts on the receiver and Safety Precautions ................................... 1

X-RAY RADIATION AND HIGH VOLTAGE LIMITS

a good earth ground. (See figure below.) Use an AC voltmeter with at Schematic Component Location ............. 1
least 5000 ohms per volt sensitivity to measure the voltage across the Schematic Notes ...................................... 2
Be aware of the instructions and procedures covering X-ray radiation. In resistor. Check all exposed metal parts and measure voltage at each point.
Voltage measurements should not exceed .75VAC, 500µA. Any value
Schematics
solid-state receivers and monitors, the CRT is the only potential source of
X-rays. Keep an accurate high voltage meter available at all times. Check exceeding this limit constitutes a potential shock hazard and must be Audio ................................................ 1
meter calibration periodically. Whenever servicing a receiver, check the corrected. If the AC plug is not polarized, reverse the AC plug and repeat Power Supply ................................... 2
high voltage at various brightness levels to be sure it is regulating exposed metal part voltage measurement at each point. System Control ................................. 2
properly. Keep high voltage at rated value, NO HIGHER. Excessive high Television ......................................... 2
voltage may cause X-ray radiation or failure of associated components.

5345
Test Equipment ........................................ 4

5345
2
DO NOT depend on protection circuits to keep voltage at rated value.
When troubleshooting a receiver with excessive high voltage, avoid close Tuner Information ................................... 1
contact with the CRT. DO NOT operate the receiver longer than

MODEL CFT27918X (CHASSIS KS3A)

necessary. To locate the cause of excessive high voltage, use a variable
AC transformer to regulate voltage. In present receivers, many electrical
and mechanical components have safety related characteristics which are
not detectable by visual inspection. Such components are identified by a
# on both the schematic and the parts list. For SAFETY, use only
equivalent replacement parts when replacing these components. Representative Model
GENERAL GUIDELINES
Essential coverage
for servicing a television receiver...
Perform a final SAFETY CHECK before returning receiver to customer.
Check repaired area for poorly soldered connections, and check entire

• Schematics
circuit board for solder splashes. Check board wiring for pinched wires or
wires contacting any high wattage resistors. Check that all control knobs,
shields, covers, grounds, and mounting hardware have been replaced. Be
sure to replace all insulators and restore proper lead dress.

• Component locations
• Parts list
Coverage includes these additional models and chassis:

Models Chassis
CFT27918X/SMS KS3A

The listing of any available replacement part herein in no case constitutes a recommendation, warranty, or guarantee by
SAMS Technical Publishing, LLC as to the quality and suitability of such replacement part. The numbers of the listed parts
have been compiled from information furnished to SAMS Technical Publishing, LLC by the manufacturers of the specific
type of replacement part listed.

Reproduction or use, without express permission, of editorial or pictorial content, in any manner, is prohibited. No patent
liability is assumed with respect to the use of the information contained herein.

© 2008 SAMS Technical Publishing, LLC

9850 E. 30th St.
Indianapolis IN 46229
For a Complete List of Manuals,
www.samswebsite.com

Printed in the United States of America 5 4 3 2 1

Page 1 SET 5345
07PF03464
!IBCGC|05345V Visit www.samswebsite.com

FEBRUARY 2008 SET 5345

AKAI
Page 1 SET 5345
TUNER INFORMATION TEST EQUIPMENT
TUNER VOLTAGE CHART TUNER TERMINAL GUIDE
Test equipment listed by participating manufacturer illustrates typical or
equivalent equipment used by Sams engineers to obtain measurements.
Pin VHF Low Band VHF High Band UHF Band This equipment is compatible with most types used by field service
technicians.
(1) AGC 2.6V 2.5V 2.9V
(2) NC 0V 0V 0V Equipment Sencore No.
(3) ID 0V 0V 0V (1)
(4) SCL 2.0V 2.0V 2.0V Oscilloscope SC3100
(2) Generators
(5) SDA 2.0V 2.0V 2.0V
(6) +5V 4.9V 4.9V 4.9V RGB CM2125
(3) Multiburst Signal VG91
(7) 33V 33.0V 33.0V 33.0V
(8) NC 0V 0V 0V Color Bar VG91
(4)
(9) IF 0V 0V 0V TV Stereo VG91
(11) SIF 2.0V 2.0V 2.0V (5) Digital VOM SC3100
(12) AFT .9V 2.0V 1.9V Frequency Meter SC3100
(13) CVBS .9V .9V 1.0V (6) Hi-Voltage Probe HP200
Accessory Probes TP212
NOTE: VHF Low Band voltages taken on channel 2. (7) Isolation Transformer PR570
VHF High Band voltages taken on channel 7. Capacitance Analyzer LC102
UHF Band voltages taken on channel 14. (8) CRT Analyzer CR7000
AC Leakage Tester PR570
(9) Inductance Analyzer LC102
Flyback Yoke Tester TVA92
Field Strength Meter SL753
Transistor Tester TF46
(11) Horizontal Analyzer HA-2500
Video Analyzer VG91, TVA92
(12)

(13)
 SET 5345 Page 1
MISCELLANEOUS ADJUSTMENTS
BASIC ADJUSTMENTS DISPLAY WHITE BALANCE Item Value Notes Item Value Notes

Turn receiver on and tune in an active station. There is a hole below the TV button Operate the receiver for 15 minutes. Tune in a white pattern. Access the service DEFLECTION OPTION
on the remote. Insert the point of a paper clip into the hole and press once. To mode, select VIDEO ADJUST 1. Select RED DRIVE item from the menu. Press the H BOW 0 Fixed do not adjust. SYSTEM CT(EN+SP+FR) -
access the service mode, turn receiver off and press the mute, 1, 8, and 2 buttons on volume up or down button to set data to a point where the screen is yellow in color. H ANGLE 0 ACS (CT, CTA) ON -
the remote. The basic adjustments display items will appear on the screen. Select BLUE DRIVE item from the menu. Press the volume up or down button to H DSCC 1 Fixed do not adjust. SOUND Stereo -
If the factory remote control is used turn the set on, press display button, then set the data values to obtain white screen. Set brightness for a visible raster. V SHIFT -27 Adjust for proper vertical size. CRT 4:3 -
factory button on the remote. The basic adjustments will be displayed as shown Alternately adjust data value of service items RED CUT OFF and BLUE CUT OFF V AMP -17 Adjust for proper vertical centering. AV MODE 2RCA+S -
below. After selecting the item desired by pressing the channel up or down button. until a good gray scale with normal white is obtained. Set the data values for V SLOPE -3 Adjust for proper vertical linearity. AUDIO MUTE ON -
Pressing the volume up or down button will change the value. To select a different normal color level. Use the red and blue drive to adjust high-light, and the red and V SC -13 Fixed do not adjust. X-RAY ON -
adjust mode after selecting or adjusting an item, press the menu button, to exit the blue cut off to adjust low-light. Repeat the process if necessary. H EW 71 VIDEO MUTE OFF -
adjust mode and save changes press the power button when in the main menu. H TRAPEZIUM -50 TILT CONTROL OFF
PURITY H PARABOLA 10 GAME+DEMO(CN) OFF
SERVICE H SYMMETRY 13 Fixed do not adjust. LNA OFF
NOTE: Operate the receiver for 15 minutes to allow warm-up of CRT. Use a H CORNER -13 PIP OFF
DEFLECTION degaussing coil to demagnetize the CRT. H SHIFT 20 V CHIP (CT, CTA) ON
VIDEO ADJUST 1
BLUE SCREEN OFF
VIDEO ADJUST 2 Set contrast to maximum. Set brightness and color to minimum. Tune in a green
VIDEO ADJUST 1 AKB OFF
VIDEO ADJUST 3 raster. Loosen the clamp screw and slide the deflection yoke back. Loosen the
RED CUT OFF 127 AUTO POWER ON OFF
OPTION (01 01 88 09) retainer screw. Adjust purity tabs to center the vertical green band. Slide the
GREEN CUT OFF 127 Fixed do not adjust. HOTEL -
RESET deflection yoke forward to produce a uniform green screen. Tighten the clamp and
G2-ADJUST retainer screws. BLUE CUT OFF 127
RED DRIVE 127 OPTION BYTE 01 01 88 09 These are hexa check
OTHERS
CONVERGENCE GREEN DRIVE 127 Fixed do not adjust. sum data value of the
VDP VERSION : Y
BLUE DRIVE 127 E2PROM, displayed
NOTE: Spread the two tabs of each set of magnets equally and opposite to SUB BRIGHT 100 on the service mode
HIGH VOLTAGE CHECK converge vertically, and rotate both tabs in the same direction to converge SUB CONTRAST 52 menu by the item of
horizontally. Since the four and six pole magnets interact, repeat the adjustment SUB COLOR 50 Fixed do not adjust. OPTION.
Tune in a picture. Set brightness, color, and picture to minimum. Connect a high until center convergence is correct. SUB TINT 70 Fixed do not adjust.
voltage probe to the CRT anode. The high voltage should read between 28kV and BCL THRSHOLD 58 Fixed do not adjust. RESET
30kV. Tune in a crosshatch pattern. Remove rubber wedges between the deflection yoke BCL GAIN 8 Fixed do not adjust. After the service adjustments are completed, Do not select RESET in the service
and CRT. Tilt deflection yoke up or down to converge the vertical lines at the top BCL TIME 10 Fixed do not adjust. mode menu. Press power button to save the new data values.
B+ CHECK and bottom of the screen and the horizontal lines at the left and right sides of the DVD SUB TINT Fixed do not adjust.
screen. Tilt the deflection yoke left or right to converge the horizontal lines at the N. YC DELAY 3 -
Turn receiver on and tune in an active station. Set picture and brightness to normal. OTHERS
top and bottom of the screen and the vertical lines at the left and right sides of the
Check the voltage at the cathode of D802, it should be 130V ±1V. VSU 105 -
screen. Repeat convergence procedure if necessary to obtain the best overall
VIDEO ADJUST 2 VSU2 0 -
convergence. Replace rubber wedges.
SCREEN ADJUST B STRETCH - BTHR 50 Fixed do not adjust. H QEW 0 -
B STRETCH - BTLT 8 Fixed do not adjust. H ZOOM PARABOLA 8 -
Tune in a color bar pattern. Access the service mode. Select G2-ADJUST. Set the CRT NECK ASSEMBLY B STRETCH - BAM 4 Fixed do not adjust. H 16:9 PARABOLA -18 -
data values as follow: CORING 31 Fixed do not adjust. DVD TINT CONTROL 0 -
CLAMP SCREW NTSC COMB FILTER 1 - PAL V SHIFT -29 -
IBRM = 200 ; WDRV = 35 ; CDL = 200 ; COL RGB = 120 120 120.
PURITY MAGNETS RGB BRIGHT 45 Fixed do not adjust. PAL H SHIFT 18 -
Turn the screen control on the high voltage transformer until the data value of item RGB CONTRAST 15 Fixed do not adjust. MELIDY VOLUME 7 -
FOUR-POLE MAGNETS
MRC RGB is about 127. Press menu button to return to service mode. Select EHT TIME 0 Fixed do not adjust.
SIX-POLE MAGNETS
VIDEO ADJUST 1, adjust the data value of red and blue cut off by one point up or EHT VERTICAL 60 Fixed do not adjust. G2 - ADJUST
RETAINER SCREW
down then restore the old value if necessary. Save the changes. DTI CORING 0 Fixed do not adjust. IBRM 195 -
DTI GAIN 1 Fixed do not adjust. WDRV 35 -
SUB BRIGHTNESS DTI BAND 1 Fixed do not adjust. CDL 170 -
COL 130 -
Tune in a picture. Access the service mode, select VIDEO ADJUST 1. Select SUB VIDEO ADJUST 3
BRIGHT item from the menu. Press the volume up or down button to set data to a
CRT PEAK THRESHOLD 255 Fixed do not adjust. VDP Version
point where highlights are just visible. SOFT LIMIT SLOPE B 4 Fixed do not adjust. VDP Version B Check the version
HARD LIMIT 255 Fixed do not adjust. mode Y, or B from
SUB CONTRAST MODULATION ON/OFF 0 Fixed do not adjust. IC201S on unit
Tune in a picture. Access the service mode, select VIDEO ADJUST 1. Select SUB A TILT POINT 0 Fixed do not adjust. number.
CONTRAST item from the menu. Press the volume up or down button to set data B TILT POINT 114 Fixed do not adjust. VDD3130 Y, or
to obtain the best contrast on the picture. GAIN 1 (VIDEO) 31 Fixed do not adjust. VDD3112 B, or
DELAY 1 (VIDEO) 3 Fixed do not adjust. VDD3108 B.
PEAK VIDEO REF 0 Fixed do not adjust. NOTE:
PEAK VIDEO GAIN 0 Fixed do not adjust. It is important to record the data values before making any changes, in case the set
LIMIT VALUE 74 Fixed do not adjust. won’t operate in a normal way, refer to the old data values.
VELOCITY DELAY 7 Fixed do not adjust.
VELOCITY CORING 10 Fixed do not adjust.
ACC REF 20 Fixed do not adjust.
ACCR 21 Fixed do not adjust.
 AKAI
MODEL CFT27918X (CHASSIS KS3A)
SET 5345 Page 1
PHILIPS MODEL 32PT5441/37 (CHASSIS L04.1UAA)
Page 2 SET 5345
SET 5345 Page 2
Page 2 SET 5345
PHILIPS MODEL 32PT5441/37 (CHASSIS L04.1UAA)
 AKAI
MODEL CFT27918X (CHASSIS KS3A)
SET 5345 Page 2
PHILIPS MODEL 32PT5441/37 (CHASSIS L04.1UAA)
Page 3 SET 5345
 SET 5345 Page 3

Important Parts Information

n Parts not listed in the parts list are commonly available at your local electronics
parts retailer.
n The parts listed here are those not usually available from a well-stocked supply cabinet or
bin.
n On the parts lists, safety items are marked with a # to remind you that only exact
replacements are recommended for these items.
n When ordering parts, state the model number, part number, and description.

Obtaining Parts

Many of these parts are available from your local Sams authorized distributor or the
manufacturer of the equipment. Call Sams for the name of your nearest distributor:
800-428-7267
Page 3 SET 5345 SET 5345 Page 3
PHILIPS MODEL 32PT5441/37 (CHASSIS L04.1UAA)
SCHEMATIC COMPONENT LOCATION GUIDE
C103 A2 C307 C43 C603 C48 C814 A37 CF02 C26 D414 E7 DZ602 B48 JA701 A45 L801 B36 QF02 C26 R251 E3 R512 B30 R720 A6 R920 D18 RG01 E26
C104 A2 C308 D6 C604 D18 C816 A39 CF03 D26 D502 D31 DZ603 B48 JA701 A8 L802 B36 QF03 C27 R252 E3 R513 B30 R721 A9 R921 A18 RG02 E26
C105 A2 C401 D41 C605 D45 C817 B37 CF04 C27 D507 B31 DZ801 D35 JA701 B4 L803 B36 QF04 D28 R301 D3 R515 A31 R722 A9 R922 E20 RG03 E26
C106 A2 C402 C43 C607 A48 C818 B37 CF05 D27 D508 C31 DZ802 C35 JA701 B45 L804 A37 QF05 C28 R302 D4 R517 D31 R723 B10 R923 E21 RG04 D26
C113 B1 C403 B43 C608 A48 C819 B37 CF06 C27 D509 D31 DZ803 C34 JA701 B45 L806 B36 QG01 E27 R303 D6 R518 D42 R802 B34 R924 D18 RG05 E27
C115 D46 C404 C44 C610 A48 C820 B39 CF07 D28 D510 C31 DZ804 B43 JA701 C45 L807 B37 QG02 E27 R304 D4 R519 E32 R803 B34 R925 A20 RG06 E28
C116 D46 C405 E7 C611 A48 C821 D36 CF08 D28 D511 A31 DZ805 D36 JA702 A6 L808 A39 QG03 E28 R305 D7 R521 D29 R804 B34 R927 B20 RG07 E28
C201 C5 C406 E8 C612 A48 C822 E37 CG01 D44 D512 B31 DZ806 D36 JA702 A9 L809 C33 QR01S D23 R306 D7 R522 D29 R805 A36 R928 B22 RG08 E27
C202 C5 C407 E6 C613 A48 C823 E38 CG02 E28 D601 C50 DZ808 C35 JA702 A9 L901 D39 QR02S D22 R309 D5 R526 D42 R806 A36 R929 A22 RL801S A35
C205 C5 C408 E6 C617 C50 C824 D38 CG03 E26 D602 D18 DZ901 A17 JR01 B4 L902 D20 QS01 A8 R310 D5 R527 D42 R807 C36 R930 A23 RL801S B34
C206 D40 C409 E7 C620 B50 C825 E40 CG04 B44 D801 B34 DZ902 E21 JR01 B45 L903 D39 QS02 A8 R313 D3 R538 C32 R808 C36 R931 A21 RM901 A17
C207 D40 C410 A40 C621 B50 C826 E40 CR01S D23 D802 A37 DZ905 B2 JR01 C45 L904 D39 QS03 B7 R314 D4 R539 B31 R809 C35 R932 B21 RP802S B34
C208 B27 C411 E14 C626 C46 C827 E38 CR02S D23 D803 C35 DZ906 E21 L102 A2 L905 D19 R102 A1 R315 D3 R542 B29 R810 C35 R933 B22 RR01S D23
C210 E40 C412 E4 C627 C46 C829 D38 CR03S D22 D804 C36 DZ907 E20 L103 A2 L907 E22 R103 A1 R401 B42 R543 D29 R811 C35 R934 B23 RR02S D23
C212 D1 C413 B44 C628 C46 C831 C40 CR04S D20 D805 B37 DZF01 B43 L201 C5 L908 D19 R105 B2 R402 B42 R544 C29 R812 D38 R935 B20 RR03S D23
C213 D3 C414 D44 C629 C46 C832 C39 CS01 A4 D806 E37 DZF02 B43 L201 D39 L909 E19 R106 B2 R403 D43 R546 D27 R813 C35 R936 E20 RR04S D23
C214 C7 C415 E12 C630 B48 C833 D36 CS02 A4 D807 B37 DZG501 D43 L202 C7 LC801S B35 R202 C6 R404 E5 R601 D46 R816 D35 R937 B20 RR05S D22

AKAI
C215 C7 C416 E13 C631 B48 C835 E38 CS03 A4 D808 B34 DZG502 E26 L204 E39 LD901 E20 R203 B9 R405 A32 R602 D46 R817 D35 R938 D20 RR06S D22
C216 C7 C418 C44 C632 B48 C837 B38 CS04 B4 D810 C40 DZR01S D23 L207 C1 LF01 D28 R204 B9 R409 E4 R603 C48 R818 D36 R939 A17 RR07S D23
C217 C7 C419 E12 C634 B49 C838 B39 CS05 B6 D811 C39 FA802S C37 L208 B2 LF02 B43 R205 E2 R410 E4 R604 D46 R819 D36 R940 D21 RR08S D22
C218 B10 C420 D10 C635 E45 C839 B40 CS06 A7 D816 E37 FA803S B37 L209 A3 LF04 D28 R206 E2 R411 E14 R605 D46 R820 D36 R941 D21 RR09S D20
C219 B9 C421 A41 C636 E46 C840 C38 CS07 C40 D901 E19 FP801S A33 L210 B6 LF05 C28 R207 C11 R412 E5 R606 D45 R821 D36 R942 E20 RR10S D21
C220 B9 C422 A42 C637 C46 C841 E37 CS08 C40 D902 D19 HIC201 D12 L212 A3 LS01 C40 R208 C11 R413 E8 R607 A48 R822 E37 R943 A21 RR430S E11

MODEL CFT27918X (CHASSIS KS3A)

C221 B11 C423 E8 C638 C46 C901 B19 CW901 A20 D903 C19 HIC202 A12 L301 E5 LX801S A34 R209 C11 R414 E14 R608 A48 R823 E37 R945 C20 RS01 A4
C222 B11 C424 E8 C639 B46 C902 B18 CW901 C22 D904 D19 HIC203 C12 L302 D7 LX802S A35 R210 C11 R415 E13 R612 C46 R824 E37 R946 C20 RS02 A7
C223 B11 C425 D8 C640 B46 C903 D18 CX801S A34 D905 A18 HIC204 B12 L303 D7 NT802S A35 R212 B6 R417 E13 R613 C46 R825 C35 R947 E20 RS03 A8
C224 D3 C426 D8 C641 A46 C904 A17 CX802S A34 D906 C49 IC202 D39 L401 E5 P800 A33 R213 E3 R418 E14 R614 C46 R827 E38 R948 E21 RS04 A7
C225 D2 C427 D8 C642 A46 C905 A18 CY802S C33 D907 E39 IC301 D5 L403 E7 PC801S D35 R214 C7 R420 E12 R615 B46 R828 C38 R949 B20 RS05 A8
C228 C6 C429 D9 C643 B46 C907 D40 D201 C11 D801S A36 IC401 C13 L405 E8 PT801S A35 R215 C7 R421 E12 R616 A46 R829 B38 RF02 D25 RS06 B7
C229 C6 C501 B29 C644 B46 C908 A21 D202 C6 DF01 D27 IC401 E13 L406 E11 Q201 C7 R216 C7 R422 C43 R617 B46 R831 C39 RF03 D26 RS07 B8
C230 E40 C502 B30 C645 E48 C909 D19 D203 D2 DF02 C28 IC501 B30 L407 E6 Q202 B27 R223 C10 R423 E13 R620 C50 R832 B34 RF04 C26 RS10 B4
C231 E40 C503 B31 C646 E48 C910 B20 D204 D2 DF03 D28 IC502 C30 L408 E8 Q203 B27 R224 C9 R424 C42 R621 A48 R833 B33 RF05 D26 RS11 B4
C232 B4 C505 C30 C647 A46 C911 A20 D205 D1 DF04 C27 IC503 A30 L410 E7 Q204 E3 R225 C9 R425 C41 R622 A48 R835 A39 RF06 D26 RY802S C33
C233 B5 C506 C31 C649 B48 C912 E20 D206 D1 DG01 E27 IC601 A47 L412 E14 Q401 E6 R226 C10 R426 E8 R627 C50 R836 A39 RF07 C26 SP1 A52
C234 B3 C507 A29 C652 B48 C913 D40 D207 E5 DR01S D23 IC602 B51 L501 A42 Q402 E4 R228 E4 R428 E12 R628 C50 R901 E20 RF08 C26 SP2 A52
C235 B3 C508 A30 C654 E48 C914 D40 D208 B27 DY D8 IC802 E39 L503 B30 Q404 E14 R231 B9 R429 E11 R629 C49 R903 D21 RF09 D28 SVM D29
C236 B8 C509 A31 C656 E46 C915 E40 D209 C28 DZ201 C10 IC803 B39 L504 C30 Q502 C29 R232 B9 R432 E12 R701 A11 R904 D20 RF10 D27 SW901 B18
C237 C6 C510 A44 C657 E46 C916 E40 D210 A28 DZ202 D4 IC804 C39 L505 A30 Q503 D29 R234 C10 R433 E6 R702 A11 R905 A19 RF11 C27 SW902 B18
C244 B3 C511 D31 C701 B6 C917 D39 D211 B28 DZ203 B26 IC901 A19 L601 B48 Q504 B29 R235 B10 R434 B38 R703 A11 R906 C20 RF12 C28 SW903 B18
C245 B6 C512 D44 C702 A3 C918 D40 D301 D5 DZ2903 C18 IC902 E21 L604 B49 Q601 C49 R236 B13 R436 D7 R704 A10 R907 C21 RF13 D28 SW904 B17
C248 C2 C513 E31 C703 A3 C919 E22 D401 C41 DZ2904 C18 IC903 D39 L605 C46 Q802 B33 R237 C13 R439 E12 R705 B4 R908 C20 RF14 D28 SW905 B17
C250 B4 C514 B44 C709 A7 C920 E22 D402 C43 DZ302 C43 IC904 D18 L606 B46 Q901 B18 R238 A13 R501 B29 R706 B11 R909 C21 RF15 C28 SW906 B17
C251 A9 C515 D44 C710 A9 C921 D40 D403 D42 DZ303 C43 IC201S B4 L607 A46 Q902 A21 R241 B2 R502 C30 R707 B11 R910 C18 RF16 C28 T401 E5
C252 A9 C516 D29 C711 A9 C922 E39 D404 E14 DZ304 D7 IC201S B9 L608 B46 Q903 A22 R242 C3 R503 B30 R708 B11 R911 B18 RF17 D28 T444S D10
C253 A9 C518 D43 C803 A36 C410A E14 D405 E13 DZ305 D7 IC201S D1 L609 B48 Q904 A21 R243 B28 R504 C31 R709 A8 R912 C19 RF18 E43 T801S A37
C254 A9 C519 D43 C804 B35 CA02 C45 D406 B38 DZ306 D7 IC801S B35 L705 C46 Q905 A22 R244 B27 R505 B31 R711 A3 R913 B18 RF19 D27 TG01 E28
C301 D4 C520 D43 C805 A36 CA03 B45 D407 E12 DZ401 E14 ICG01 E26 L706 C46 Q906 B20 R245 B26 R506 C29 R712 A3 R914 B19 RF20 B43 TU01S A2
C302 D5 C521 D43 C807 C36 CF10 D28 D408 E6 DZ402 E6 ICG01 E27 L709 A3 Q908 B21 R246 B26 R507 D30 R715 C17 R915 B18 RF21 B43 V999 C32
C303 C5 C522 D43 C808 C34 CF11 C28 D409 D9 DZ503 D42 ICS01 A4 L710 A3 Q909 C20 R247 C25 R508 C30 R716 C17 R916 B18 RF22 B43 VP801S B33
C304 D6 C523 D43 C809 C35 CF12 C29 D411 A41 DZ504 D42 J412 E7 L712 A6 Q910 C20 R248 C9 R509 D31 R717 C17 R917 B17 RF23 C27 VX801S A33
C305 D7 C526 D44 C810 C35 CF14 E44 D412 D9 DZ505 D43 J901 B50 L713 A9 Q911 B23 R249 C9 R510 C31 R718 C17 R918 B17 RF24 D28 X201 D2
C306 D4 C601 C48 C811 C35 CF01 C26 D413 D8 DZ601 C48 JA701 A3 L714 A9 QF01 D26 R250 C9 R511 A29 R719 B5 R919 C18 RF25 D28 X601 E46
X901 A20

SET 5345 Page 3

Page 4 SET 5345
PARTS LIST
Item No. Type No. Mfr. Part No. Notes Item No. Type No. Mfr. Part No. Notes

D201, 02 1N4148 0401-000005 - DZ305 UZ39BSB 0403-001221 -

D203 Thru DZ306 TZP33A 0403-000700 -
D206 RB441Q 0404-000156 - DZ401 MTZJ15C 0403-001325 -
D207 1N4148 0401-000005 - DZ402 1N4148 0401-000005 -
# D208 1N4148 0401-000005 - DZ503 MTZJ12B 0403-001211 -
D209, 10, 11 1N4148 0401-000005 - DZ504, 05 MTZJ15C 0403-001325 -
D301 TVR10G 0402-000546 - DZ601 MTZJ5.6B 0403-000508 -
# D401 RU20A 0402-000540 - DZ602 MTZJ9.1B 0403-000720 -
D402 RG10V 0402-000534 - DZ603 MTZJ5.6B 0403-000508 -
D403 1N4004 0402-000132 - DZ801 MTZJ8.2B 0403-001322 -
D404 RU20A 0402-000540 - DZ802 MTZJ5.6B 0403-000508 -
D405 1R5GU41 0402-000493 - DZ803 MTZJ30D 0403-001167 -
D406, 07 1N4004 0402-000132 - DZ804 TZP33A 0403-000700 -
D408 1R5GU41 0402-000493 - DZ805 KA431LZ 1203-001217 -
D409 RU20A 0402-000540 - DZ806 MTZJ5.6B 0403-000508 -
D411 TVR10G 0402-000546 - DZ808 MTZJ7.5B 0403-000719 -
D412 RGP15G 0402-000010 - DZ901, 02 MTZJ5.6B 0403-000508 -
D413 RH1A 0402-000537 - DZ905 Thru
D414 - - - DZ907 MTZJ5.6B 0403-000508 -
D502 1N4004 0402-000132 - DZ2903, 04 MTZJ5.6B 0403-000508 -
D507 Thru DZG501, 02 - - -
D512 ERB43-04SV1 0402-001105 - DZF01, 02 MA2560 0403-001039 -
D601, 02 1N4148 0401-000005 - # DZR01S MTCJ6.8C 0403-001321 -
D801 1N5397GP 0402-001111 - HIC201 Thru
# D801S GSIB650 0402-001399 - HIC204 DRGB001A AA13-00093A -
D802 FMG-26S - - # IC201S VDP3130Y-B2 1204-001812 -
D803 TVR10G 0402-000546 - # IC301 LA7845 1204-000517 -
# D804 1N4148 0401-000005 - # IC401 393 1202-000103 -
D805, 06, 07 FML-G12S - - # IC501, 02, 03 TDA6101Q AA61-10060A -
D808, 10, 11 1N4004 0402-000132 - # IC601 MSP3451G-PO-A2 1204-001737 -
D816 TVR10G 0402-000546 - # IC602 TDA7297 1201-001064 -
D901 Thru # IC801S KA3S1265RD AA13-00101A -
D905 RB441Q 0404-000156 - # IC802 KA78R05 - -
D906 1N4148 0401-000005 - # IC803 KA78R08 1203-001697 -
D907 1N4004 0402-000132 - # IC804 KA7806 1203-000284 -
DF01 1N4148 0401-000005 - # IC901 SIM-408A3 AA09-00243A -
DF02, 03 ERB43-04SV1 0402-001105 - # IC902 24WC16 1103-001177 -
DF04 1N4148 0401-000005 - # IC903 78RM33 1203-001944 -
DG01 1N4148 0401-000005 - # IC904 KIA7025AP 1203-001943 -
DR01S RG10V 0402-000534 - ICG01 MC4558C 1201-000191 -
DZ201, 02 MTZJ5.6B 0403-000508 - # ICS01 TEA6425 1001-001114 -
DZ203 MTZJ6.8C 0403-001321 - LD901 SL-255D AA96-00461A -
DZ302, 03, 04 MTZJ24B 0403-001329 - # PC801S TR130 0604-001038 -
 SET 5345 Page 4
PARTS LIST continued
Item No. Type No. Mfr. Part No. Notes Item No. Function/Rating Mfr. Part No. Notes
Q201 Thru # CY802S .0033 20% 400VAC 2201-000446 -
Q204 KSC815 0501-000389 - # DY Yoke AA27-00083A -
Q401 C5802D - - F801A, B Fuse Holder 3602-000114 For FP801S
Q402 KSC2073-H2 0502-001007 - # FA802S Fuse 3601-001086 5Amp, 125V, Fast Acting
Q404 IRF620 0505-000156 - # FA803S Fuse 3601-001086 5Amp, 125V, Fast Acting
Q502, 03, 04 KSA539 0501-000283 - Fuse 3601-001228 10Amp, 125V, Fast Acting
Q601 KSC815 0501-000389 - # FP801S Fuse 3601-001012 4Amp, 250V, Slow Blow
Q701 KSC815 0501-000389 - J412 Ferrite Bead 3301-000287 -
Q802 KSC2331-Y 0501-000369 - J901 Ferrite Bead 3301-000287 -
Q901 Thru JA701 Jack 3722-001031 Assembly
Q906 KSC815 0501-000389 - JA702 Jack 3722-001423 Assembly
Q908 KSC815 0501-000389 - JR01 Jack 3722-001031 Assembly
Q909, 10 2N7000 0505-000109 - L102 22µH 2701-000159 -
Q911 KSC815 0501-000389 - L103 10µH 2701-000115 -
QF01, 02 KSC815 0501-000389 - L201, 02 10µH 2701-000114 -
QF03 KSC2331-Y 0501-000369 - L203 10µH - -
# QF04 2SC2344-D 0502-000153 - L204, 06 4.7µH 2701-000184 -
# QF05 2SA1011-D 0502-000131 - L207 Ferrite Bead 3301-000287 -
# QR01S KSA539-Y 0501-000283 - L208, 09, 10, 12 3.3µH 2701-000168 -
# QR02S KSC815 0501-000389 - L301 10µH 2701-000114 -
QS01, 02, 03 KSC815 0501-000389 - L302, 03 Ferrite Bead 3301-000287 -
L403 Horizontal Linearity AA27-00099A -
Item No. Function/Rating Mfr. Part No. Notes L405 Horizontal Width AA27-00096A -
C224, 25 5pF ±.5pF 50V NPO 2201- 002031 - L406 10µH 2701-000114 -
C303 15pF 5% 500V NPO 2201-002103 - L407 Filter 2901-000297 -
C405 .0077 3% 1.6kV 2306-000330 - L408 Horizontal Width AA27-00103A -
C406 .0012 5% 1.6kV 2306-000322 - L410, 12 Ferrite Bead 3301-000287 -
C407 680pF 5% 1.6kV 2301-001338 - L501 33µH 2701-000178 -
C501, 07 15pF 5% NPO 2201-000247 - L503, 04 Ferrite Bead 2901-000297 -
C513 .01 20% 3kV 2201-002063 - L505, 06 Ferrite Bead 3301-000287 -
C612, 13 1µF 20% 50V NP 2401-001914 - L601 10µH 2702-001094 -
C626, 28 4.7µF 20% 50V NP 2401-001989 - L604 3.9µH 2701-000169 -
C654 56pF 5% 50V NPO 2201-000611 - L605 Thru
C656, 57 1pF ±.25pF 50V NPO 2201-000304 - L608 33µH 2701-000177 -
# C803 470µF 20% 250V 2401-001386 - L609 - 2701-000297 -
# C804, 05 .0022 20% 250VAC 2201-000332 - L701, 02, 05, 06 33µH 2701-000177 -
C814 270pF 10% 2kV 2201-000406 - L709, 10 3.3µH 2701-000168 -
C910, 11 30pF 5% 50V NPO 2201-000980 - L711 10µH 2701-000114 -
# CR01S 470pF 10% 500V 2201-000556 - L712, 13, 14 - - -
# CR02S, 03S 10µF 20% 16V 2401-002235 - L801 Ferrite Bead 3301-001223 -
# CR04S .47 5% 63V 2305-000412 - L802, 03, 04 Ferrite Bead 3301-000287 -
CW901 100pF 20% 50V X 4 Network 2503-000156 - L806 Ferrite Bead 3301-001223 -
# CX801S, 02S .22 20% 250VAC 2306-000318 - L807 Ferrite Bead 2901-000297 -
 PARTS LIST continued
Item No. Function/Rating Mfr. Part No. Notes Item No. Function/Rating Mfr. Part No. Notes
L808 24µH AA27-00098A - # RR03S 20K 5% 1/8W 2001-000009 -
L809 Ferrite Bead 3301-000287 - 43.2K 1% 1/2W 2004-001897 -
L901 10µH 2702-001094 - # RR04S 62K 5% 1/8W 2001-000908 -
L902 4.7µH 2701-000184 - # RR05S 9100 5% 1/8W 2001-001015 -
L903, 04 10µH 2702-001094 - 20K 1% 1/2W 2004-000531 -
L907 10µH 2701-000114 - # RR06S 8200 5% 1/8W 2001-000977 -
L908, 09 47µH 2701-000191 - # RR07S 10K 5% 1/8W 2001-000290 -
# LC801S Degaussing AA27-20002Q - # RR08S 1000 5% 1/8W 2001-000429 -
LF01 Ferrite Bead 3301-000287 - # RR09S 470 5% 1/8W 2001-000780 -
LF02 100µH 2701-000112 - # RR10S 10K 5% 1/8W 2001-000290 -
LF04, 05 Ferrite Bead 2901-000297 - # RR430S 1000 5% 1/2W 2001-001088 -
LS01 10µH 2701-000114 - # RY802S 4.7M 5% 1/2W 2002-001013 -
# LX801S, 02S Line Filter AA29-00012A - SG501 Thru
# NT802S NTC 1404-001045 - SG504 Spark Gap AA27-00084A -
# P800 Line Cord AA39-10007Y AC, Polarized SP1, 2 Speaker 3001-001115 8 Ohms, 15W
# PT801S PTC 1404-000002 - SVM SVM - -
R212 10K 1% 1/8W 2004-000218 - SW901 Switch 3404-000244 Menu
R301 3900 1% 1/2W 2004-004048 - SW902 Switch 3404-000244 Volume Down
R302 20K 1% 1/2W 2004-000531 - SW903 Switch 3404-000244 Volume Up
R304 .47 5% 2W Fusible 2008-000018 - SW904 Switch 3404-000244 Channel Down
R313 6800 1% 1/8W 2004-001137 - SW905 Switch 3404-000244 Channel Up
R314 35.7K 1% 1/2W 2004-001986 - SW906 Switch 3404-001004 Power
R315 62K 1% 1/8W 2004-004970 - # T401 Horizontal Drive AA26-50001L -
R405 .68 5% 2W Fusible 2008-000254 - # T444S (1) Horizontal Output AA26-00105A -
R413 .47 10% 2W Fusible 2008-001018 - # T801S Switching AA26-00046A -
R415 6800 1% 1/2W 2004-001402 - # TU01S Tuner AA40-00074A TCPN3081PA09A(B)
R417 13K 1% 1/2W 2004-001382 - # V999 CRT AA03-00360A A68QCP891X100(M)
R420 6800 1% 1/2W 2004-001402 - # VA999 Socket 3704-001114 CRT
R424, 25 .47 10% 2W Fusible 2008-001018 - # VP801S Varistor 1405-000152 -
R526 2700 1% 1/8W 2004-000500 - X201 Crystal 2801-003432 20.25MHz
R527 1000 1% 1/8W 2004-000433 - X601 Crystal 2801-003903 18.432MHz
R807 120 5% 5W 2006-001083 - X901 Crystal 2801-003728 6MHz
R811 91K 1% 1/2W 2004-001408 - PC Board AA97-01677A CRT
R819 2490 1% 1/2W 2004-001983 - PC Board AA41-00345A Side AV
R821 133K 1% 1/2W 2004-001891 - PC Board AA94-07051A Main
R827 .1 10% 2W Fusible 2008-000284 - PC Board AA98-00126A Switch
R828 1 5% 2W Fusible 2008-000266 - Transmitter AA59-00141G Remote, TM58
R829 5.6 5% 2W Fusible 2008-001029 -
# RL801S Relay 3501-001040 Degaussing # For SAFETY use only equivalent replacement part.
RM901 Receiver AA59-60001U Remote (1) Screen and focus controls are part of T444S.
# RP802S 1.8M 5% 1/2W 2002-001010 -
# RR01S 1 5% 1W Fusible 2008-000264 -
# RR02S 43K 5% 1/8W 2001-000766 -

Page 4 SET 5345

 AKAI
MODEL CFT27918X (CHASSIS KS3A)
AKAI MODEL CFT27918X (CHASSIS KS3A) SET 5345 Page 4